GENERAL NOTES:

1. LOCATION OF ALL MECHANICAL, ELECTRICAL, PLUMBING AND FIRE PROTECTION

EQUIPMENT/ SYSTEMS ARE NOT YET FINAL. ALL PROVISIONS SHOWN ON THE
DRAWING ARE SUBJECT TO CHANGE UPON FINALIZATION OF MEPFS DESIGN.
2. KITCHEN LAYOUT ARE NOT YET FINAL. KINDLY REFER TO KITCHEN CONSULTANT
ON ALL DRAWINGS AND SPECIFICATIONS REFLECTED ON DRAWING.

J H G 3. VERIFY ALL STRUCTURAL ITEMS TO STRUCTURAL ENGINEER BEFORE

PROCEEDING ANY WORK ON SITE.
4. ACOUSTIC PROPERTIES ARE NOT YET FINAL. KINDLY REFER TO ACOUSTIC
CONSULTANT ON ALL DRAWINGS AND SPECIFICATIONS REFLECTED ON DRAWING.
FLOOR PLAN NOTES:
1 1. VERIFY AND COORDINATE ALL DIMENSIONS AND ALL EXTERIOR DOOR AND
WINDOW LOCATIONS WITH ARCHITECT'S DRAWINGS.

REFER TO SETTING OUT PLAN 2 OF 3

2. REFER TO DOOR TAGGING PLAN AS REFLECTED ON FLOOR PLAN AND DOOR
00-25066 SCHEDULE FOR ALL INTERIOR DOORS INFORMATION.
3. COORDINATE ALL SERVICE EQUIPMENT AND REQUIREMENTS WITH CONSULTANTS.
3 4. ALL PARTITIONS TO BE ADEQUATELY BRACED IN COMPLIANCE WITH THE
REQUIREMENTS OF ALL APPLICABLE SEISMIC AND BUILDING CODES.
L7-48111 5. CONTRACTOR TO PROVIDE ADEQUATE WOOD BLOCKING AS REQUIRED FOR
D10 INSTALLATION AND MOUNTING OF MILLWORKS, ACCESSORIES AND OTHER

5' EOWD10
NECESSARY INSTALLATIONS AS INDICATED ON DRAWINGS.
6. DIMENSIONS ARE TAKEN FROM THE FINISHED FACE OF WALLS. DIMENSIONS
LOCATING DOORS BY EDGE ARE TO THE INSIDE EDGE OF JAMB, UNLESS
OTHERWISE NOTED.
7. PROVIDE WATER- RESISTANT SUBSTRATE AT ALL SURFACES TO BE EXPOSED TO
WATER AND/ OR TO RECEIVE CERAMIC TILE.
8. CONTRACTOR TO VERIFY SETTING-OUT OF FINISHES ON DRAWINGS AND ON SITE

50

150
WITH DESIGNER (ARCHITECT/INTERIOR) PRIOR TO FINAL LAYING OUT OF FINISHES.
1250 1200 860 1180 1180 1180 1180 1180 860 1180 1180 480 800 1080 1180 860 1095 1195 860 1190 9. CONTRACTOR TO SUBMIT SAMPLE/S OF ALL HARDWARE, ACCESSORIES AND
FINISHES AS SPECIFIED FOR APPROVAL PRIOR TO FULL-PURCHASING.
18040 2000 10. CONTRACTOR TO SUBMIT SHOP DRAWINGS FOR ITEMS NOT SHOWN IN THE
DRAWING SET AND IS REQUIRED TO BE DONE AT SITE TO COMPLETE THE WORKS
FOR APPROVAL PRIOR TO IMPLEMENTATION ON SITE.
11. CONTRACTOR TO VERIFY AND MARK ON SITE THE SETTING-OUT FOR ALL TOILET
D10 1 FIXTURES. TO VERIFY MANUFACTURER'S INSTALLATION REQUIREMENTS AND

2000

1800
2 PREPARATIONS NEEDED FOR PROPER INSTALLATION OF ALL FIXTURES.
12. REFER TO ACOUSTIC CONSULTANT'S DRAWING PACKAGE FOR SOUND INSULATION
EOWD10 L7-48110 L7-48111 RATING AND SPECIFICATION.
13. REFER TO DOOR SCHEDULE FOR ALL INTERIOR DOOR INFORMATION.
14. VERIFY AT JOBSITE ALL DIMENSIONS PRIOR TO CONSTRUCTION.
15. CONTRACTOR TO VERIFY TERMINATIONS ON SITE WITH THE DESIGNER.
245 1200 1200 145 1000 525 1200 1200 1200 1200 1200 425 2000 675 1170 1210 2680 1255 735 1200 1200 735 16. REPORT TO INTERIOR DESIGNER ANY INCONSISTENCIES AND CONFLICTS FOUND
AT JOBSITE PRIOR TO ADJUSTMENT ON DESIGN AND DETAILS IN DRAWINGS (IF
D10

150
ANY).

50
FLOOR FINISH NOTES:
1. ALL WALL FINISHES ARE INDICATED ON ELEVATION DRAWINGS.
2. THIS PLAN INDICATES THE TYPES OF FINISHES. FLOOR FINISHES TO CONTINUE TO
TOE KICK OR BASE OF MILLWORK. REFER TO DETAILS INDICATED FOR ADDITIONAL
D9A SD04 INFORMATION.
3. ALL FINISH MATERIALS PROVIDED MUST COMPLY WITH THE REQUIREMENTS OF
APPLICABLE CODES, RULES, REGULATIONS, LAWS, ORDINANCES, ETC. AS
REQUIRED BY THE PUBLIC AUTHORITIES.
EOSD9 4. ALL STONE AND TILE FINISHES INSTALLED AT FLOOR SURFACES ARE TO MEET OR

5 EXCEED SLIP COEFFICIENT RATIO AS REQUIRED BY CODE.

5. ALL FLOOR FINISHES TO BE INSTALLED IN ACCORDANCE WITH MANUFACTURERS
SPECIFICATIONS FOR THE PARTICULAR APPLICATION INDICATED ON DRAWINGS.
6. VERIFY FLOOR LEVEL CHANGES, CONTRACTOR TO LEVEL SUB FLOOR AS
REQUIRED FOR PROPER INSTALLATION OF FLOOR FINISH MATERIAL.
7. CONTRACTOR TO SUBMIT SAMPLES OF ALL FINISHES FOR WRITTEN APPROVAL
4 4 PRIOR TO INSTALLATION. INSPECT ALL MATERIALS FOR DEFECTS PRIOR TO
INSTALLATION.
8. THE PURPOSE OF THIS DRAWING IS FOR CONTRACTOR'S REFERENCE WITH
FIRE DOOR SIGN BY L7 EXECUTIVE OFFICES CORRIDOR MALE RESTROOM SIGN BY
REGARDS TO SURFACE PREPARATION (DEPRESSIONS) PRIOR TO HANDOVER.
9. CONTRACTOR'S SHALL PROVIDE REQUIRED LEVELING FILLS AND GROUTS TO
SIGNAGE CONSULTANT 1 SETTING OUT PLAN PART 1 OF 3 SIGNAGE CONSULTANT
RENDER ALL FLOOR FINISH TO FLOOR FINISH TRANSITION LEVEL.
10. REFER TO ARCHITECTURAL DRAWINGS FOR ALL FINISH FLOOR LINE.
11. REFER TO ARCHITECTURAL/ STRUCTURAL FOR ANY TOILET & KITCHEN SLAB
L7-48100 SCALE 1:50 (A1) / 1:100 (A3) DEPRESSION.
AUXILLARY PLAN NOTES:
1. POWER/ DATA RECEPTACLES TO BE MOUNTED AT 300mm ABOVE FINISHED FLOOR TO
CENTERLINE IF COVER PLATE MOUNTED HORIZONTAL UNLESS OTHERWISE INDICATED ON
DRAWINGS. VERIFY ORIENTATION WITH ELEVATIONS AND CONFIRM CODE REQUIREMENTS.
4 4 NOTIFY DESIGNER OF ANY DISCREPANCIES.

G F E
2. POWER/ DATA RECEPTACLES ABOVE COUNTERS TO BE MOUNTED AT 150mm ABOVE
FINISHED COUNTERTOP TO CENTERLINE OF COVER PLATE, TYPICAL UNLESS OTHERWISE
NOTED.
REFER TO SETTING OUT PLAN 1 OF 3

REFER TO SETTING OUT PLAN 3 OF 3

3. ALL FLOOR BOXES TO BE FULLY RECESSED WITH METAL FLUSH BOX COVER. COVER FINISH
DIRECTIONAL SIGN BY BRC EXEC. OFFICE SIGN TO BE SELECTED BY DESIGNER.
4 4. ALL WORK SHALL BE PERFORMED IN COMPLIANCE WITH THE REQUIREMENTS OF
SIGNAGE CONSULTANT BY SIGNAGE CONSULTANT APPLICABLE CODES, RULES, REGULATIONS, LAWS, ORDINANCES, ETC. AS REQUIRED BY
THE PUBLIC AUTHORITIES. IN THE EVENT OF A CONFLICT THE MOST STRINGENT
REQUIREMENT SHALL GOVERN.
5145 1500 4390 3110 5. ELECTRICAL CONTRACTOR SHALL COORDINATE WITH ALL OTHER TRADES THE
INSTALLATION OF ELECTRICAL FIXTURES AND SYSTEMS.
6. WHERE TELEPHONE, DATA AND/ OR ELECTRICAL RECEPTACLES APPEAR BACK-
TO-BACK,JUNCTION BOXES SHALL BE STAGGERED TO REDUCE NOISE TRANSMISSION
THROUGH PARTITION.
7. VERIFY IN FIELD THAT NO CONFLICTS EXIST WHICH WOULD PROHIBIT THE LOCATION OF
D1 ANY AND ALL MECHANICAL, ELECTRICAL, TELEPHONE, LIGHTING, PLUMBING, AND

5' EOWD1
SPRINKLER EQUIPMENT (INCLUSIVE OF ALL PIPING, DUCTWORK AND CONDUIT) AND THAT
ALL REQUIRED CLEARANCES FOR INSTALLATION AND MAINTENANCE OF ABOVE EQUIPMENT
IS PROVIDED.
8. PAINTED SWITCH AND/ OR OUTLET COVER PLATES,SPEAKERS, FIRE EXTINGUISHER
CABINETS, ELECTRICAL PANELS AND ACCESS PANELS TOO BE SHOPFINISHED. FACTORY
PAINT FINISH TO MATCH COLOR SELECTED BY DESIGNER.
9. ALL ELECTRICAL SWITCH & OUTLET RECEPTACLES PLEASE REFER TO FF&E LIST OF
SPECIFICATIONS.
860 1190 1190 1190 1190 1190 1190 1190 860 1055 1055 1055 860 955 955 955 955 1085 625 650 1160 1045 FF&E NOTES:
1. FOR ALL ROUGH CARPENTRY AND BLOCKING, INSTALL FIRE- RETARDANT TREATED WOOD
20950 2000 AS REQUIRED TO COMPLY WITH THE REQUIREMENTS OF APPLICABLE CODES, RULES,
REGULATIONS, LAWS, ORDINANCES, ETC. AS REQUIRES BY THE PUBLIC AUTHORITIES.
2. COORDINATE INSTALLATION OF IN-WALL STEEL ANCHORAGES, GROUNDS AND
1 2 LIFT DIRECTORY SIGN BY 4 4 MISCELLANEOUS BLOCKING WITH OTHER CONTRACTORS TO DETERMINE PRECISE
LOCATIONS.
L7-48110 L7-48111 SIGNAGE CONSULTANT 3. MILLWORK CONTRACTOR SHALL OBTAIN AND VERIFY ALL FIELD MEASUREMENTS AND
CONDITIONS AFFECTING HIS/ HER WORK AND SHALL BE RESPONSIBLE FOR ALL DETAILS
AND DIMENSIONS ASSURING PRECISION FITTING AND PROPER ASSEMBLY OF HIS/ HER
58290 PRODUCTS.
4. WORK SHALL BE ACCURATELY SET PLUMB, LEVEL AND SECURE FASTENED TIGHTLY AND
1200 1200 735 1150 1200 410 1000 290 1250 975 1005 600 2700 600 1165 1115 1065 1000 650 1160 775 1200 775 1160 570 ACCURATELY TO ADJACENT SURFACES, AND SECURELY ANCHORED IN POSITION INDICATED
ON DRAWINGS AND APPROVED SHOP DRAWINGS.
D9 NOTE: 5. REPAIR, REPLACE OR OTHERWISE MAKE GOOD ALL DAMAGE INCURRED TO PRE-FINISHED

100

100
WOODWORK DURING HANDLING AND INSTALLATION.
- FOR ALL ELECTRICAL SWITCHING, REFER TO 6. ADJUST DOORS, DRAWERS AND ALL HARDWARE FOR PROPER OPERATION AND CLEAN ALL
CABINET SURFACES, INSIDE AND OUTSIDE.
ELECTRICAL AND LIGHTING CONSULTANT 7. SHOP DRAWINGS OF ALL MILLWORK ITEMS TO BE SUBMITTED TO DESIGNER FOR WRITTEN
EOWD7 SD03B - MEPF REFERENCE DATED MAY 2021
APPROVAL PRIOR TO FABRICATION.
8. STAINED CABINET AND DOOR FINISHES ARE TO BE SHOP- FINISHED UNLESS OTHERWISE
NOTED.
- MEPF & ELV LOCATIONS FOR COORDINATION WITH 9. ALL LOOSE FURNITURE REFLECTED HEREIN ARE REPRESENTATION ONLY AND ARE NOT
MEPF & ELV CONSULTANTS PART OF THE BASE BUILDING CONTRACT. THIS WILL BE PART OF THE INTERIOR FIT-OUT

5 - REFER TO ARCHITECTURAL FOR THE FINAL WALL

TYPES AND DESIGNATION PLAN
CONTRACTOR'S SCOPE.
10. FOR MATERIAL CODES & SYMBOLS PLEASE REFER TO FF&E LIST OF SPECIFICATIONS.
11. VERIFY AT JOBSITE ALL DIMENSIONS PRIOR TO CONSTRUCTION.
12. REPORT TO INTERIOR DESIGNER ANY INCONSISTENCIES AND CONFLICTS FOUND AT
JOBSITE PRIOR TO ADJUSTMENT ON DESIGN AND DETAILS IN DRAWINGS (IF ANY).
- FOR THE KITCHEN LAYOUT & LOCATION OF REFLECTED CEILING NOTES:
4 KITCHEN EQUIPMENTS, REFER TO KITCHEN 1. LOCATIONS OF ALL HVACS GRILLES, SMOKE DETECTORS, SPRINKLERS, FIRE ALARMS,
SECURITY CAMERAS, SPEAKERS, ETC. BY CONSULTANTS ARE TO BE COORDINATED WITH
CONSULTANT. DESIGNER.
2. EXIT SIGNS AND ILLUMINATIONS TO CONFORM IN COMPLIANCE WITH THE REQUIREMENTS

FEMALE RESTROOM SIGN - FOR FINAL SIGNAGE LOCATION, REFER TO OF APPLICABLE CODES, RULES, REGULATIONS, LAWS, ORDINANCES,ETC. AS REQUIRED BY
THE PUBLIC AUTHORITIES. IN THE EVENT OF A CONFLICT THE MOST STRINGENT
SIGNAGE CONSULTANT. REQUIREMENTS SHALL APPLY.
BY SIGNAGE CONSULTANT - FIRE-RETARDANT-TREATED PANELING: PANELS 3. PAINTED SPRINKLER COVER PLATES, SPEAKERS, LIGHT FIXTURE TRIM RINGS, FIRE
L7 EXECUTIVE OFFICES CORRIDOR EXTINGUISHER CABINETS, ELECTRICAL PANELS AND ACCESS PANELS TO BE SHOP-
FINISHED, FACTORY PAINT FINISH TO MATCH COLOR SELECTED BY THE DESIGNER.
SHALL CONSIST OF WOOD VENEER AND
2 SETTING OUT PLAN PART 2 OF 3 4 FIRE-RETARDANT; MEDIUM-DENSITY FIREBOARD
4. PAINT ALL DUCTWORK BLACK BEHIND DIFFUSER GRILLES, TYPICAL UNLESS OTHERWISE
NOTED.
5. ALL PAINT SHALL BE APPLIED IN ACCORDANCE WITH MANUFACTURERS RECOMMENDATION
L7-48100 SCALE 1:50 (A1) / 1:100 (A3) (MDF). PANELS SHALL HAVE A FLAME-SPREAD INDEX FOR THAT PARTICULAR SURFACE. TWO- COAT MINIMUM APPLICATION REQUIRED, UNLESS
OTHERWISE NOTED.
SOLAIRE EXEC. OFFICE OF 25 OR LESS AND A SMOKE-DEVELOPED INDEX OF 6. COORDINATE ALL A/V EQUIPMENT LOCATIONS AND REQUIREMENTS WITH A/V CONSULTANT.
7. ELECTRICAL/ MECHANICAL DRAWING PROVIDED ARE FOR THE PLACEMENT AND/ OR
4 450 OR LESS AS PER ASTM E84, AND BE LISTED AND
REFER TO SETTING OUT PLAN 2 OF 4

SIGN BY SIGNAGE GENERAL ARRANGEMENT OF FIXTURES, OUTLETS, ETC. AS RELATED TO THE DESIGN
LABELED BY A TESTING AND INSPECTING AGENCY INTENT. ALL REQUIRED ENGINEERING AND/ OR CALCULATIONS TO BE PERFORMED BY

E 1 D CONSULTANT
C ACCEPTABLE TO AUTHORITIES HAVING
JURISDICTION.
OTHERS, UNLESS OTHERWISE NOTED.
8. REFER TO REFLECTED CEILING PLAN FOR INSTALLATION LOCATIONS OF ALL CEILING
MOUNTED DECORATIVE LIGHT FIXTURES.
9. REFER TO ELECTRICAL, HVAC AND FIRE PROTECTION DRAWINGS FOR SWITCHING, EXIT
00-25066 SIGNS, EMERGENCY LIGHTING, DUCT, GRILLE, DIFFUSER LOCATIONS AND COORDINATION
4 OF SPRINKLER HEAD LOCATIONS. ANY CONFLICT WITH LIGHTING FIXTURE LOCATIONS

L7-48111
L7 KEY PLAN SHALL BE BROUGHT TO THE ATTENTION OF THE OWNER AND COORDINATE.
10. INTERIOR DESIGN (ID) CEILING PLANS ARE INTENDED TO SHOW CEILING FINISHES AND
PROFILES ONLY.
11. SEE INTERIOR DESIGN (ID) FLOOR PLANS FOR LOCATION OF ADDITIONAL DECORATIVE
D1
5'
LIGHTING NOT SHOWN ON CEILING PLANS (I.E. STAIR LIGHTS, AISLE LIGHTS). ALSO
4 5 5' 6 INDICATED ON FLOOR PLAN ARE SPECIAL OUTLET LOCATIONS REQUIRED FOR PLUG-IN
FLOOR AND TABLE LAMPS. (COORDINATE WITH ELECTRICAL DRAWINGS, ID FURNISHINGS
EOWD1 PLANS AND DECORATIVE LIGHT FIXTURES AND CATALOGUE CUTS).
12. THE PURPOSE OF THIS DRAWING IS FOR CONTRACTOR'S REFERENCE FOR DECORATIVE
L LIGHT FIXTURE AND ACCESSORIES (CHANDELIER) POSITIONS/ LOCATIONS FOR NECESSARY
SUPPORT SYSTEM PROVISIONS.

200
13. SEE INTERIOR ELEVATIONS FOR LOCATION AND MOUNTING HEIGHTS OF WALL MOUNTED
1085 625 650 1160 1045 1045 1045 1045 1160 1045 1045 1045 1045 1160 1380 FIXTURES. SEE DETAILS FOR SPECIAL LIGHT FIXTURE MOUNTING CONDITIONS.

2000 14000
K 14. CONTRACTOR TO PROVIDE SHOP DRAWINGS FOR ALL CASEWORKS FOR MOCKING-UP.
15. PROVIDE ADEQUATE BLOCKING CEILING AND/ OR WALL TO SUPPORT CEILING MOUNTED
DECORATIVE LIGHT FIXTURES AND ARTWORKS.
200 900 200 16. CEILING SERVICE ACCESS TO PLS. REFER TO MEPF LAYOUT (SUBJECT FOR DESIGNER'S

2 D4 J APPROVAL).
1 17. REFER TO LIGHTING CONSULTANT DRAWINGS FOR ALL LIGHTING REQUIREMENTS,

1700
SPECIFICATIONS AND DETAILS.
L7-48110 L7-48111 18. REFER TO LIGHTING CONSULTANT'S DRAWINGS FOR FIXTURE TYPE AND LOCATION OF ALL
EOWD4 H ARCHITECTURAL FUNCTIONAL LIGHTING.
19. REFER TO M&E CONSULTANT'S DRAWINGS FOR AIR CONDITIONING SYSTEM.
20. REFER TO ACOUSTIC CONSULTANT FOR CEILING INSULATION AND STC/ NRC RATING FOR
ADEQUATE DETAIL.
650 1160 775 1200 775 1160 570 2000 650 1160 980 980 990 1160 550 1000 980 905 1300 G 21. ALL CEILING HEIGHTS TO BE VERIFY ON SITE.
22. VERIFY AT JOBSITE ALL DIMENSIONS PRIOR TO CONSTRUCTION.
D10 D9

200
23. CONTRACTOR TO VERIFY TERMINATIONS ON SITE WITH THE DESIGNER.
24. CONTRACTOR TO PROVIDE MARKING OF LIGHT POINTS POSITION FOR DESIGNER'S
F APPROVAL BEFORE INSTALLATION.
25. REPORT TO INTERIOR DESIGNER ANY INCONSISTENCIES AND CONFLICTS FOUND AT
JOBSITE PRIOR TO ADJUSTMENT ON DESIGN AND DETAILS IN DRAWINGS (IF ANY).
SD04B EOSD9A E FOR CONSTRUCTION DRAWING
This Drawing is the property of CASAS+ARCHITECTS and is not to be reproduced or copied in whole
or in part. It is only to be used for the project and site specifically identified herein and is not to be used
D on other projects. It is to be returned upon request.

5 4 SOLN-CR-SUR-NP-0032 DECEMBER 20, 2021

C 3 SOLN-CR-SUR-NP-0029 SEPT 30, 2021
2 SOLN-CR-PBD-BA101-0054 AUGUST 10, 2021
AUGUST 10, 2021
SL/FL-03

B 2 SOLN-CR-SUR-NP-0010
AUGUST 10, 2021
2 SOLN-CR-SUR-NP-0009
2 SOLN-CR-SUR-NP-0011 AUGUST 10, 2021
N
L7 EXECUTIVE OFFICES CORRIDOR 2 SOLN-CR-SUR-NP-0006 AUGUST 10, 2021
1 CLARIFICATION APRIL 30, 2021
3 SETTING OUT PLAN PART 3 OF 3 0
REV NO
CONSTRUCTION DRAWING
DESCRIPTION
MARCH 2021
DATE
L7-48100 SCALE 1:50 (A1) / 1:100 (A3)
ISSUE STATUS:
0 1 2 5 10

SCALE 1:200 METERS

ISSUED FOR CONSTRUCTION
ARCHITECT STRUCTURAL CONSULTANT MEPF CONSULTANT ARCHITECTURAL CONSULTANT INTERIOR DESIGN CONSULTANT QUANTITY SURVEYOR RELEVANT CONSULTANT PROJECT OWNER DRAWING TITLE
REG. NO. 5411
L7 EXECUTIVE OFFICES
CORRIDOR
TIN 146-555-136
SETTING OUT PLAN

PTR 8857200 www.habitusdesigngroup.com

SOLAIRE NORTH PROJECT NO.: SCALE: 1:25 (A1)1:50 (A3) DRAWN: CAS
JOSE A. SY SURESTE PROPERTIES INC.
DRAWING NO.: REV No.
FORSSPAC AEDAS PTE LTD
CARMELO T. CASAS ISSUED ON 01/06/2022 SY^2 + ASSOCIATES, INC. STRUCTURAL ENGINEER No. 117, 2nd Flr, Prince Bldg, The Metropolis Tower 2,
HABITUS SOLN-CD-ID-CAS-L7-48100 4
9801 Kamagong St., cor. Rada Street, Legaspi Village, 11 North Buona Vista Drive,
Baticulin St., Makati City REG. NO. 22404 TIN 123-489-697 Makati, Philippines REG. NO. TIN #12-07, Singapore 138589 228 Pasong Tamo Ext.
E: [email protected] T: +65 6734 4733 (Chino Roces Ave.) Level 5, Tower 6789, Ayala Avenue, ALL MEASUREMENTS ARE TO BE VERIFIED ON SITE BY CONTRACTOR. ALL DISCREPANCIES ARE TO BE IMMEDIATELY REPORTED TO
Penthouse, Paseo Center, 8757 Paseo De Roxas PTR NO. 7333196 DATE 01-03-19 T:+632 310 5130 PTR NO. DATE ARCHITECTS & PROJECT MANAGERS. CONTRACTORS ARE TO PREPARE & SUBMIT SHOP DRAWINGS TO ARCHITECTS PRIOR TO
ISSUED AT MAKATI CITY T: 893-4157 / 896-9760 F:+65 67346233 Makati Metro Manila Philippines Barangay Bel-Air, Makati,
Avenue, Salcedo Village, Makati City F:+632 310 5134 1, ASEAN AVENUE, ENTERTAINMENT CITY, TAMBO, PARAÑAQUE CITY, PHILIPPINES
COMMENCEMENT OF WORKS. THIS DRAWING, ACTING AS INSTRUMENT OF SERVICE, IS THE PROPERTY OF CASAS+ARCHITECTS, INC.
/ 896-9755 PLACE MAKATI CITY PLACE www.aedas.com T: +63 920 974 4852 1226 Metro Manila, Philippines EDSA, VERTIS NORTH, QUEZON CITY, PHILIPPINES & CANNOT BE REPRODUCED WITHOUT THEIR WRITTEN CONSENT. REPUBLIC ACT No. 9266
M:+63 928 500 4727
GENERAL NOTE: DO NOT SCALE FROM DRAWING. USE MARKED DIMENSIONS. TO BE READ IN CONJUNCTION WITH ALL OTHER CONSULTANT'S DRAWINGS. THE ARCHITECT TO BE IMMEDIATELY NOTIFIED OF ANY DISCREPANCIES. COPYRIGHT ON THE DRAWING RETAINED BY THE ARCHITECT.