Erection

SL ITEM DESCRIPTION QTY UNIT

RATE AMOUNT
A HV INSTALLATION

SUPPLY AND INSTALLATION OF SUB-STATION EQUIPMENT

The rates under this section shall also include:

This schedule of Quantities shall be read in conjuction with the technical specification,
1
General & Special conditions as well as all tender drawings.

2 Supporting rigid frame work.

3 All fixing accessories such as foundation bolts, nuts and bolts etc as required.

4 Touching up all damaged paint with approved paint shade.

5 Rubber mats shall be provided in front and back of the HT switchgear as per IS 15652-2006.

All control cabling including termination between transformer and HT switchgear as

6
required.

Interlocking shall be provided between transformer door and HT breaker panel. When
7
transformer door
open respective SF6 breaker shall be tripped.

9 All protection relays shall be microprocessor based.

10 Provision shall be made for all HT breakers to be hooked up with BAS for status indication.

A HV INSTALLATION

I SUPPLY AND INSTALLATION OF SUB-STATION EQUIPMENT

Supply,installation, testing and commissioning of RMU Panel consisting of 11 KV 1250A LBS

1 with Fuse of 2 Nos. incoming and 1 no. outgoing 1250 Amps 18.4 KA for 1 sec. VCB as per 1 Nos 6,000.00 6,000.00
feeder details given in the specification and single line diagram. (As per RAPDRP)

2 Electricity Board Metering Panel (11 KV) 1 Nos 2,500.00 2,500.00

Design, fabrication assembling, wiring, supply, installation, testing and commissioning of

cubicle type 11 KV metering panel fabricated out of 14 gauge CRCA sheet steel, free
standing floor readable dust and vermin proof outdoor type (Degree of protection for
enclosure shall be IP-55) with arrangement for sealing the covers and doors, reinforcement
of suitable size angle iron, channel T section or flats wherever necessary. Cable gland plate
shall be provided on bottom of the metering panel. Panel shall be treated with all anti
crossing process before power coating. Approval shall be taken from Local electricity board
inform of shop drawing before fabrication. Metering panel shall comprises of the following:

Trivector meter of SECURE make or approved equal by Local Electricity Board of accuracy
class 0.2
Metering cubicle as described above.

Dual Ratio 5 Amps Secondry CT of suitable burden but not less than 15 VA accuracy Class
0.5

1 of 39
 Erection
SL ITEM DESCRIPTION QTY UNIT
RATE AMOUNT
The potential transformer shall be as specified below:
Ratio : 11000/ V3/ 110/ V3/ 110 V
V A Burdan : 100 V A for 100/V3 and 110 V winding
Class : CL –1 for both the windings.
Basic Insulation level : Same as mentioned for VCB in clause -6.
Over voltage factor : 1.2 Continuous
Single phase PT’S shall be used and shall be connected in Star/ Star.

CT/ PT shall be of approved make and design of Local Electricity Board.

3 Electricity Board Metering Panel (11 KV)-CHECK METER 1 Nos 2,500.00 2,500.00

Design, fabrication assembling, wiring, supply, installation, testing and commissioning of

cubicle type 11 KV metering panel fabricated out of 14 gauge CRCA sheet steel, free
standing floor readable dust and vermin proof outdoor type (Degree of protection for
enclosure shall be IP-55) with arrangement for sealing the covers and doors, reinforcement
of suitable size angle iron, channel T section or flats wherever necessary. Cable gland plate
shall be provided on bottom of the metering panel. Panel shall be treated with all anti
crossing process before power coating. Approval shall be taken from Local electricity board
inform of shop drawing before fabrication. Metering panel shall comprises of the following:

Trivector meter of SECURE make or approved equal by Local Electricity Board of accuracy
class 0.2
Metering cubicle as described above.

Dual Ratio 5 Amps Secondry CT of suitable burden but not less than 15 VA accuracy Class
0.5

The potential transformer shall be as specified below:

Ratio : 11000/ V3/ 110/ V3/ 110 V
V A Burdan : 100 V A for 100/V3 and 110 V winding
Class : CL –1 for both the windings.
Basic Insulation level : Same as mentioned for VCB in clause -6.
Over voltage factor : 1.2 Continuous
Single phase PT’S shall be used and shall be connected in Star/ Star.

CT/ PT shall be of approved make and design of Local Electricity Board.

Supply,installation, testing and commissioning of HT Panel consistinf of 1250 Amps 11 KV

4 HT VCB of 1 Nos. incoming and 2 nos. outgoing 1250 Amps LBS with Fuse as per feeder 1 Nos 6,500.00 6,500.00
details given in the specification and single line diagram.

Supply, installation, testing and commissioning of 11 / 0.433 KV compact package sub

station comprising 11 KV 1250 A VCB breaker as incomer cum outgoing with metering &
protection 2500 KVA 11 / 0.433 KV Dry type transformer & LT panel consisting of 1 no.
5 2 Set 15,000.00 30,000.00
4000 A 4 Pole manually operated fixed type air circuit breaker. All ACB shall have
Microprocessor based release unit. Package sub-station shall be complete as per
specification.

Supply, installation, testing and commissioning of 200 AH capacity 24 volts DC hermetically

6 3 Set 1,600.00 4,800.00
sealed maintenance free lead acid batteries duly charged.

Supply, installation, testing and commissioning of battery charger unit with provisions of
7 Boost Charing, and Float charging. Suitable for 240 V single phase + 10% AC, 50 Hz power 3 Set 2,100.00 6,300.00
supply as per specifications.

Supply and fixing in position the approved “Shock Treatment Charts” written in English and
8 4 No. 80.00 320.00
Local Language. These charts shall be framed in teak wood frame and covered with glass.

9 Supply and fixing in position the fire extinguishers carbon-di-odide type 2.5 Kgs capacity. 4 No. 80.00 320.00

2 of 39
 Erection
SL ITEM DESCRIPTION QTY UNIT
RATE AMOUNT
Supply and fixing in position the best quality Danger Boards of approved shape and size as
10 4 No. 40.00 160.00
specified by Local Electricity Authorities written in English & Local Languages.

Supply and fixing in position 1000 mm wide rubber matting of 11KV grade as per electricity
11 50 RM 50.00 2,500.00
rules.

Supply of fire buckets 5 nos. in each set duly filled with fine sand and fixed on an angle iron
12 frame as per requirement of local authorities. Fire buckets shall be painted red from 3 Sets 500.00 1,500.00
outside and white from inside with additional handle at the bottom.

Supply and fixing in position the approved single line diagram framed in 1000 x 800 mm size
13 3 No. 100.00 300.00
glass frame in the sub station.

14 Supply of first aid box of approved make as per specification. 5 No. 100.00 500.00

15 Supply of tool kit with 1 pair 11 KV rubber hand gloves of approved make. 2 No. - -
TOTAL CARRIED TO SUMMARY 64,200.00

B HT CABLES & LT CONTROL CABLES

The rates under this section shall also include the following:

This schedule of Quantities shall be read in conjuction with the technical specification,
1
General & Special conditions as well as all tender drawings.

2 Providing and fixing approved cable supports and grouting the same as required.

3 Effecting proper connections at terminations.

Ensuring that provision is left in buildings and trenches as the work proceeds, for
4
incorporating of cable
supports at a later date.

5 Providing all, fixing accessories such as clamping devices, nuts and bolts etc.

6 Clamping to supports where laid in trenches.

7 Providing proper supports for cable terminals as called for.

8 Wherever cables cross walls provide proper sleeves at the time of civil work.

B HT CABLES & LT CONTROL CABLES

Supplying and laying following size 11 KV grade XLPE aluminium conductor armoured
1
cables laid over MS supports in existing trenches.
3 C x 300 sq.mm 11 KV XLPE cable (between metering panel room to HT panel and HT
1.1 RM 94.00 -
panel to transformers).

3 C x 240 sq.mm 11 KV XLPE cable (between metering panel room to HT panel and HT
1.2 220 RM 80.00 17,600.00
panel to transformers).

3 C x 185 sq.mm 11 KV XLPE cable (between metering panel room to HT panel and HT
1.3 RM 70.00 -
panel to transformers).

Supplying and making cable end terminations for the following size of 11KV grade, XLPE
2 aluminium conductor armoured cable including termination kit complete heat shrinkable
sleeve etc.

2.1 3 C x 300 sq.mm 11 KV XLPE cable Nos. 2,500.00 -

2.2 3 C x 240 sq.mm 11 KV XLPE cable 12 Nos. 2,500.00 30,000.00

2.3 3 C x 185 sq.mm 11 KV XLPE cable Nos. 2,200.00 -

3 of 39
 Erection
SL ITEM DESCRIPTION QTY UNIT
RATE AMOUNT

3 Supplying, laying GI sleeves of following sizes:

3.1 150 mm dia RM 150.00 -

Supplying and laying of following 1100 volts grade PVC insulated sheathed copper
4 conductor armoured control cables in existing trenches cables trays, clamped on wall with
suitable saddles, fixing bolts, including testing and commissioning.

4.1 12 Core 2.5 sq mm PVC insulated copper conductor armoured control cables 50 RM 18.00 900.00

Cable end termination of the following PVC insulated sheathed aluminium conductor
5 armoured cables of 1100 volt grade including supplying and fixing of crimping lugs. Double
compression glands with earthing provision and cable sockets

5.1 12 Core 2.5 sq.mm Control cable 4 Nos. 104.00 416.00

TOTAL CARRIED TO SUMMARY 48,916.00

E. EARTHING INSTALLATION (FOR POWER DISTRIBUTION SYSTEMS,

LIFTS, LT PANELS,UPS SYSTEM & EPABX

Rates shall also include the following :

This schedule of Quantities shall be read in conjuction with the technical specification,
1
General & Special conditions as well as all tender drawings.

2 All fixing accessories such as saddles, screws rawl plugs etc.

Jointing by rivetting and brazing after rivetting in case of copper and welding / bolting in
case
3 of GI earthing.

4 Cutting chases / holes and making good the same wherever required.

5 Effecting adequate and proper interconnections.

6 Use of copper thimbles.

7 Earthing system shall comply to IS:3043-1987.

8 All earthing pits shall be interconnected.

All equipment motors, DB’s, panels to be connected on both ends (double earthing) with
suitable
9 strip / wires.

10 Soil resistingly test shall be conducted of the area where earth pits are to be located.

E. EARTHING INSTALLATION (FOR POWER DISTRIBUTION SYSTEMS & UPS SYSTEM

Supply and fixing of following bare copper /GI tapes / wires including all necessary fixing
1
accessories and effecting connections as per specifications.

1.1 50 x 10 mm thick GI tape. 75 RM 55.00 4,125.00

1.2 50 x 6 mm thick GI tape. 1067 RM 40.00 42,680.00

1.3 32 x 6 mm thick GI tape. RM 35.00 -

1.4 25 x 3 mm thick GI tape. RM 28.00 -

1.5 50 x 6 mm thick CU tape. 374 RM 50.00 18,700.00

4 of 39
 Erection
SL ITEM DESCRIPTION QTY UNIT
RATE AMOUNT

1.6 8 SWG GI wire RM 6.00 -

6 Maintenance free earthing electrode / chemical earthing (Alternate-II)

Providing and laying of 14.35 mm dia and 3 meter length.copper bonded earth rod in 150
mm dia. in an augured hole in ground , surrounded by ground enhancement material as per
specification. Inspection chamber shall be of 400 x 500 mm with concrete base CI manhole
cover with frame painted with bitumastic paint. 2 Nos. of 50 x 6 mm cross section & 300
6.1 mm long copper strip to be clamped with copper claded rod electrode have sufficient nos ( 29 Nos. 4,000.00 116,000.00
But not less than 4 Nos.) of 10 mm dia. GI nuts & bolts for connection to the equipment /
interconnection to the other pits to form equi-potential bonding .The pH value of ground
enhance material shall be 6.9 to 7.2 of 1000gm / lit @ 20 deg.c.The minimum 30 Kg of
ground enhancement material shall provided for each electrode.

Providing earthing stations at locations as called for including providing and laying 600 x
600 x 3.15 mm thick tinned copper electrode with 2 Nos 50 x 6 mm thick copper strip,
from earth electrode to inspection chamber,50 mm dia medium class G I pipe CI /
chequered plate funnel with 20 gauge G I wire mesh, masonry chamber 1000 x 500 mm
Nos. 4,500.00 -
with concrete base, CI chequered plate manhole cover with frame and bitumastic paint
and packing of mixture of charcoal and common salt around plate electrode complete
with digging of pit upto permanent misture level but not less than 3 metres and back filling
as required.

Supply and installation of 50 x 6 mm Cu busbar mounted on insulators and having 6 nos.

holes for terminating single core 35 Sq.mm flexible cable with the entire assembly enclosed
7 Nos. 4,500.00 -
in 1.6 mm thick MS enclosure of approved make, design & painted with approved paint
shade. (for UPS/low volt earthing and installed in electrical shaft).

TOTAL CARRIED TO SUMMARY 181,505.00

A. CIRCUIT CUM POINT WIRING

The rates for all point wiring items shall also include supplying and fixing of the following:

This schedule of Quantities shall be read in conjuction with the technical specification,
1
General & Special conditions as well as all tender drawings.

Conduits, conduit supporting structural members including spacers, clamps etc, bushes
2
and other fittings as well as
deeper JB with PVC connectors.

3 Approved GI saddles and grouting the same for exposed conduit work.

4 1.6 mm thick Outlet boxes and junction box.

5 All fixing accessories such as clips, brass screws etc.

Qoated rate for MCB controlled primary point shall include all the materials and works
6
necessary including circuit length from MCB DB upto 1st switch board.

Embedding conduits and accessories in walls and floors etc. during construction and / or
7 cutting chases (with chase cutting machine) and making good the same as necessary in
the case of concealed conduit work.

8 Switch, socket outlet and necessary blank plates wherever required.

PVC insulated copper conductor stranded flexible PVC insulated wire of Green colour or
9
Green colour
with yellow band for earthing of fixtures, outlet boxes and third pin of socket outlet.

10 Repainting of conduits, outlet boxes and junction boxes where ever damaged.

5 of 39
 Erection
SL ITEM DESCRIPTION QTY UNIT
RATE AMOUNT
11 All wires shall be IS approved, 1100 volt grade, stranded flexible PVC insulated, FRLS wires.

All sockets shall be shuttered type with earth terminal. All sockets for UPS system shall be
12
provided with distinct RED dot on the socket for easy identification.

Suitable rating of plugs top shall also be provided within the quoted rates for all industrial
13
type and splash proof
socket outlets.

14 Separate neutral and earthing wire shall be provided for each circuit.

15 Lighting and power circuit to be kept separate.

PVC conduits shall be used for embeded conduiting where as GI conduits shall be used for
16
surface conduiting
in places with saline & humid climate where as MS conduits shall be used for surface
conduiting in places with
dry climate.

A. CIRCUIT CUM POINT WIRING

Common Area + Toilet area

Wiring of following light points with 1.5 sq.mm PVC insulated copper conductor 1100 volts
grade stranded flexible FRLS wires in embeded 25mm dia. heavy duty FRLS PVC conduit as
per IS 9537 part-3 or surface mounted 25 mm dia 16 gauge GI conduit including providing
1
and fixing of 6 amps single pole rocker operated flush mounted switches of approved
quality colour make and design in 1.6 mm thick GI box and earthing of fixture and the
outlet box with 1.5 Sq.mm PVC insulated copper conductor stranded flexible FRLS wire.

MCB controlled Primary point (from DB to switch board & from DB to 1st Light point-Avg
1.1 1098 Pt 720.00 790,560.00
length 30 mtr)

MCB controlled Secondary point ( from light point to light point - cost of switch & board
1.2 2675 Pt 288.00 770,400.00
NOT included-Avg length 12 mtr)

Primary point with switch ( from switch board to first point - cost of switch & board
1.3 665 Pt 275.00 182,875.00
included- Avg length 10 mtr)

Secondary point without switch & Borad ( from light point to light point - cost of switch &
1.4 761 Pt 120.00 91,320.00
board NOT included-Avg length 5 mtr)

Secondary point (from switch board to switch board looping- cost of switch & board NOT
1.5 124 Pt 190.00 23,560.00
included)

Wiring for following 250 volt single phase and neutral 6 amps switch socket outlet with
2.5 sq.mm PVC insulated copper conductor 1100 volts grade stranded flexible FRLS wires in
embeded 25mm dia. heavy duty FRLS PVC conduit as per IS 9537 part-3 or surface
2 mounted 25 mm dia 16 gauge GI conduit, including providing and fixing of 6 amps switch
and 6A 3 pin socket of approved make colour and design in 1.6 mm thick GI box with grid
plate and earthing of third pin of the socket outlet and the GI box with 2.5 Sq.mm PVC
insulated copper conductor stranded flexible FRLS wire.(Avg length 30 mtr)

2.1 Maximum 2 nos. of 6A switch socket in one circuit 42 Pt 750.00 31,500.00

Wiring for 250 volts single phase and neutral 6/16 amps switch and socket outlet with
2.5 sq.mm PVC insulated copper conductor 1100 volts grade stranded flexible FRLS wires
in embeded 25mm dia. heavy duty FRLS PVC conduit as per IS 9537 part-3 or surface
3 mounted 25 mm dia 16 gauge GI conduit, including providing and fixing of 16 amps switch
and 5 pin socket of approved make and design in 1.6 mm thick GI boxes with grid plates
and earthing the third pin of socket outlet with 2.5 Sq. mm PVC insulated copper
conductor stranded flexible FRLS wire. (Avg length 30 mtr)

6 of 39
 Erection
SL ITEM DESCRIPTION QTY UNIT
RATE AMOUNT

3.1 Maximum 1 nos. of 6/16A switch socket in one circuit 12 Pts. 750.00 9,000.00

3.2 Maximum 2 nos. of 6/16A switch socket in one circuit 90 Pts. 800.00 72,000.00

Wiring for Exhaust fan point with 2.5 sq. mm. Insulated copper conductor 1100 volts grade
stranded flexible FRLS wires of approved make in 25mm dia. 2mm thick embeded PVC
conduit or surface mounted 25 mm dia 16 gauge GI conduit including providing and fixing of
4 6 amps flush mounted switch at the normal switch level in 2 mm thick GI box and 6 amps 3 20 Pts. 300.00 6,000.00
pin flush mounted socket outlet near exhaust fan and earthing of exhaust fan through the
third pin of the socket outlet and GI box with 2.5 sq. mm. PVC insulated copper
conductor strande flexible FRLS wire.

LIFT SHAFT (LIFT VENDOR SCOPE)

Supply, installation & wiring of 230 V bulk head lamp with on/off switch for Lift shafts with
3C x 2.5 sq.mm YWY cable in 32 mm dia MS surface mounted conduits including providing
5 and fixing bulk head light, 6A switch with earth wire. For costal area GI conduit accessories
shall be considered where as for non costal areas MS conduits & accessories shall be
considered. (Exclude cost of bulk head fitting)

5.1 10 Nos.Bulk head lamps with switch on one circuit 36 Pts 870.00 31,320.00

Wiring for following 250 volts single phase and neutral 6 amps switched socket outlet for lift
shafts with 3C x 2.5 Sqmm YWY cable in surface mounted 32 mm dia 16 gauge GI conduit
6 including providing and fixing of 16 amps 3 pin switched socket of approved make and
design in 2 mm thick GI boxes with grid plates and earthing of third pin of socket outlet
and GI box

6.1 10 Nos. 6 amps switched socket outlet on one circuit 36 Pts. 890.00 32,040.00

7.0 PVC pipes

Supply and laying of 2 mm thick rigid FRLS PVC conduits in concealed conduit system using
conduit accessories like junction boxes, collars, bends, elbows, binding wires, etc.

7.1 25 mm dia conduit Mtrs 19.00 -

7.2 20 mm dia conduit Mtrs 17.00 -

TOTAL CARRIED TO SUMMARY 2,040,575.00

B. CABLES, MAINS AND SUB MAINS

The rate shall also include the following :

This schedule of Quantities shall be read in conjuction with the technical specification,
1
General & Special conditions as well as all tender drawings.

Cable supporting structural members including spacers, clamps etc, bushes and other
2
fittings

3 Providing all fixing accessories such as clamping devices nuts, bolts and screws.

4 Wherever the cables are of aluminium and bus bars of copper bimetallic lugs shall be used.

5 All cable shall be laid with one diameter gap.

6 All cables shall be IS approved.

7 Double compression glands

Fire retardent paint one meter on both side of wall penetration and at termination as per
8
specifications.

7 of 39
 Erection
SL ITEM DESCRIPTION QTY UNIT
RATE AMOUNT

9 Burried LT cables to be laid atleast 750 mm below ground.

B. CABLES, MAINS, SUB MAINS AND CABLE TRAYS

Supplying & laying of following 1100 volt grade XLPE insulated PVC inner sheathed and
FRLS PVC outer sheathed aluminium conductor armoured cables as per specification in
1
existing trenches, cable trays, ducts, clamped to wall with suitable clamps including, saddles
fixing bolts, connecting testing and commissioning.

1.1 3.1/2 core 400 sq. mm 36 RM 90.00 3,240.00

1.2 3.1/2 core 300 sq. mm 5436 RM 70.00 380,520.00

1.3 3.1/2 core 240 sq. mm. 90 RM 60.00 5,400.00

1.4 3.1/2 core 185 sq. mm 1630 RM 55.00 89,650.00

1.5 3.1/2 core 150 sq. mm 2610 RM 45.00 117,450.00

1.6 3.1/2 core 120 sq.mm 412 RM 42.00 17,304.00

1.7 3.1/2 core 95 sq. mm 980 RM 40.00 39,200.00

1.8 3.1/2 core 70 sq. mm 235 RM 35.00 8,225.00

1.9 3.1/2 core 50 sq. mm 4987 RM 32.00 159,584.00

2.10 3.1/2 core 35 sq. mm 295 RM 30.00 8,850.00

2.11 3.1/2 core 25 sq. mm 784 RM 27.00 21,168.00

Supplying & laying of following 1100 volt grade XLPE insulated FRLS PVC outer sheathed
copper conductor armoured cable as per specification in existing trenches, cable trays
2
ducts , clamped to wall with suitable clamps, including fixing bolts, connecting testing and
commissioning.

2.1 4 core 16 sq.mm 874 RM 24.00 20,976.00

2.2 4 core 10 sq.mm 520 RM 22.00 11,440.00

2.3 4 core 6 sq.mm 2215 RM 19.00 42,085.00

2.4 4 core 4 sq.mm 4295 RM 14.00 60,130.00

2.5 4 core 2.5 sq.mm RM 10.00 -

2.6 2 core 6 sq.mm RM 14.00 -

2.7 2 core 4 sq.mm RM 11.00 -

Providing Mains Wiring from Meter panel panel to DB using copper conductor PVC
insulated FR wires in rigid PVC conduits of 32 mm and 1.8mm wall thickness ISI mark,
3 concealed in wall & ceiling with necessary boxes/pull boxes complete with continuous
earthing up to main switchboard from the Distribution board using PVC insulated green
color copper earth-wire.
3.1 4 x 6 sq.mm + 1 x 4 sq mm copper wire RM 27.00 -

3.2 2 x 6 sq.mm +1 x 4sq mm copper wire RM 17.00 -

3.3 2 x 4 sq.mm +1 x 2.5 sq mm copper wire 1895 RM 15.00 28,425.00

3.1 4 x 4 sq.mm +1 x 2.5 sq mm copper wire 1265 RM 24.00 30,360.00

8 of 39
 Erection
SL ITEM DESCRIPTION QTY UNIT
RATE AMOUNT
Cable end termination of the following XLPE insulated FRLS PVC outer sheathed
4 aluminium/copper conductor armoured cables of 1100 volt grade including supplying and
fixing of bimettalic crimping lugs, double compression glands with earthing.

4.1 3.1/2 core 400 sq. mm.Aluminium Cable 2 Nos. 450.00 900.00

4.2 3.1/2 core 300 sq. mm.Aluminium Cable 96 Nos. 350.00 33,600.00

4.3 3.1/2 core 240 sq. mm. Aluminium Cable 6 Nos. 300.00 1,800.00

4.4 3.1/2 core 185 sq. mm. Aluminium Cable 30 Nos. 250.00 7,500.00

4.5 3.1/2 core 150 sq. mm. Aluminium Cable 98 Nos. 220.00 21,560.00

4.6 3.1/2 core 120 sq. mm. Aluminium Cable 20 Nos. 180.00 3,600.00

4.7 3.1/2 core 95 sq. mm. Aluminium Cable 18 Nos. 150.00 2,700.00

4.8 3.1/2 core 70 sq. mm. Aluminium Cable 4 Nos. 130.00 520.00

4.9 3.5 core 50 sq. mm Aluminium Cable 42 Nos. 110.00 4,620.00

4.10 3.5 core 35 sq. mm Aluminium Cable 6 Nos. 100.00 600.00

4.11 3.5 core 25 sq. mm Aluminium Cable 16 Nos. 80.00 1,280.00

4.12 4 core 16 sq. mm copper cable 18 Nos. 80.00 1,440.00

4.13 4 core 10 sq. mm copper cable 12 Nos. 75.00 900.00

4.14 4 core 6 sq. mm copper cable 56 Nos. 70.00 3,920.00

4.15 4 core 4 sq. mm copper cable 92 Nos. 64.00 5,888.00

4.16 4 core 2.5 sq.mm copper cable Nos. 50.00 -

4.17 2 core 6 sq.mm copper cable Nos. 38.00 -

4.18 2 x 4 sq.mm +1 x 2.5 sq mm copper wire 166 Nos. 24.00 3,984.00

Supply and fixing of factory fabricated GI ladder type cable trays, with radial bends,
5
suspenders and supports as per specification and of the following sizes.

5.1 1000 mm wide 80 RM 150.00 12,000.00

5.2 750 mm wide RM 100.00 -

5.3 600 mm wide RM 90.00 -

5.4 450 mm wide RM 80.00 -

Supply and fixing of perforated type factory fabricated GI cable trays of the following sizes
6
including providing GI suspenders and supports as per specifications..

6.1 750 mm wide 135 RM 110.00 14,850.00

6.2 600 mm wide 120 RM 100.00 12,000.00

6.3 450 mm wide 1452 RM 86.00 124,872.00

6.4 300 mm wide 110 RM 73.00 8,030.00

6.5 150 mm wide 1527 RM 49.00 74,823.00

6.6 100 mm wide 50 RM 45.00 2,250.00

9 of 39
 Erection
SL ITEM DESCRIPTION QTY UNIT
RATE AMOUNT
TOTAL CARRIED TO SUMMARY 1,387,644.00

A DISTRIBUTION BOARDS

Design, fabrication, assembling, supply, installation, testing and commissioning of Main LT

panel, Main Distribution Panels, Sub Distribution panels and Final Distribution panels
suitable for 415 V, 3 phase, 50 Hz, 4 wire power supply system.

Panels shall be fabricated out of 2 mm thick CRCA sheet steel in cubical formation,
compartmentalized in Form 3b Construction, floor mounted, free standing and shall be dust
and vermin proof. 3 mm thick cable gland plate, shall be provided both at the top and the
bottom of the panel.

Final distribution panels shall be fabricated out of 1.6 mm thick CRCA sheet steel and shall
be wall mounted. All large panels shall be provided with lifting hooks. Distribution panels
shall be fabricated in accordance with the specifications.

Note :
1.All switchgear feeders shall be with BMS compatible. Additional NO/NC shall be
required for status monitoring and remore tripping arrangement.
2. All energy meters shall be with BMS compatible with required latest communication
mode.
3.Energy meters and necessory metering arrangement shall be such that it will be easily
comunicable with BMS software protocall.
4. Electrical contractor/ panel builder shall be closely design the panel in closely
communication with BMS team.

1 Main LT Panel
(For Transformer supply)
A. Section – I

A 4000Amps FP rating Auto Transfer Switch as per specification.

Metering for Grid side & DG side supply.
Phase indicating light through 415 /110 V PT, Primary / Secondary of PT's shall be protected
i.
by 2 amps MCB’s.

3 Nos. 96 x 96 sq.mm 0-4000 / 5 amps CTR digital ammeter with 3 nos 4000. / 5 amps, 15
ii
VA Class I CT’s.

96 x 96 mm sq. 0-500 Volt digital voltmeter with selector switch through 415 V / Ö3 :
iii
110 V /Ö3 PT’s, Primary and Secondary of PT’s shall be protected by 2 amp TP MCB’s

iv Load Manager conserve EM 6400 with KWH reading for Grid supply

v 3 nos 4000. / 5 amps, 15 VA Class I CT’s.

B. Incoming Air Circuit Breaker `A’

4000 amps TPN electrically operated fully drawout type air circuit breaker with built in
microprocessor based release unit for protection and measurment as per specification and
with following accessories :

i. Phase indicating light through 230 V, shall be protected by 2 amps SP MCB's.

ii. Breaker ON / OFF / TRIP indicating lights with control MCB’s.

iii. Under voltage release

iv. 24 V DC Shunt trip coil

v Under voltage relay with timer (27)

vi. Over voltage relay with timer (59)

vii. Breaker control switch

10 of 39
 Erection
SL ITEM DESCRIPTION QTY UNIT
RATE AMOUNT

3 Nos. 96 x 96 sq.mm 0-4000 / 5 amps CTR digital ammeter with 3 nos 4000. / 5 amps, 15
viii
VA Class I CT’s.

96 x 96 mm sq. 0-500 Volt digital voltmeter with selector switch through 415 V / Ö3 :
ix.
110 V /Ö3 PT’s, Primary and Secondary of PT’s shall be protected by 2 amp TP MCB’s

Class – C, 20KA, TVSS surge arrestor(Lines to Neutral) & (Neutral to Earth) suitable for 3
x
phases, 4 wire.

C. Bus Bars

6300 amps 4 pole (65 KA) Aluminium bus bars with colour coded heat shrinkable insulating
sleeves

D. Outgoing

4000. amps FP electrically operated fully drawout type air circuit breaker with ON/OFF/TRIP
i. indicating lamps with MCB’s and microprocessor based release for protection & indication
as per specification.

1000. amps FP electrically operated fully drawout type air circuit breaker with ON/OFF/TRIP
ii indicating lamps with MCB’s and microprocessor based release for protection & indication
as per specification.

iii 630. amps TPN MCCB

iv 630. amps TPN MCCB (Spear)

4000. amps FP electrically operated fully drawout type air circuit breaker with ON/OFF/TRIP
v indicating lamps with MCB’s and microprocessor based release for protection & indication
as per specification.(Spear with compartment only)

E Bus Coupler : Breaker `C’

4000 amps TPN electrically operated fully drawout type air circuit breaker with ON / OFF /
TRIP indicating lamps with control MCB’s, shunt trip, breaker control switch etc.

Section-II
(For transformer supply)
K 4000Amps FP rating Auto Transfer Switch as per specification.
Metering for Grid side & DG side supply.
Phase indicating light through 415 /110 V PT, Primary / Secondary of PT's shall be protected
i.
by 2 amps MCB’s.

3 Nos. 96 x 96 sq.mm 0-4000 / 5 amps CTR digital ammeter with 3 nos 4000. / 5 amps, 15
ii
VA Class I CT’s.

96 x 96 mm sq. 0-500 Volt digital voltmeter with selector switch through 415 V / Ö3 :
iii
110 V /Ö3 PT’s, Primary and Secondary of PT’s shall be protected by 2 amp TP MCB’s

iv Load Manager conserve EM 6400 with KWH reading for Grid supply

v 3 nos 4000. / 5 amps, 15 VA Class I CT’s.

L Incoming Air Circuit Breaker ‘B’

4000 amps FP electrically operated fully drawout type air circuit breaker with built in
microprocessor based release unit for protection & measurment as per specification and
with following accessories :

i. Phase indicating light through 230 V, shall be protected by 2 amps SP MCB's.

ii. Breaker ON / OFF / TRIP indicating lights with control MCB’s

11 of 39
 Erection
SL ITEM DESCRIPTION QTY UNIT
RATE AMOUNT
iii. Under voltage release

iv. 24 V DC Shunt trip coil.

v Under voltage relay with timer (27)

vi. Over voltage relay with timer (59)

vii. Breaker control switch

3 Nos. 96 x 96 sq.mm 0-1250 / 5 amps CTR digital ammeter with 3 Nos.1250. / 5 amps 15
viii
VA CL:1 CT’s

0-500 Volt digital voltmeter with selector switch 96 x 96 mm sq. through 415 V / √3 : 110
ix.
V /√3 PT’s, Primary and Secondary of PT’s shall be protected by 2 amp TP MCB’s

Class – C, 20KA, TVSS surge arrestor(Lines to Neutral) & (Neutral to Earth) suitable for 3
x
phases, 4 wire.

M Bus Bars

6300 amps 4 pole (65 KA) Aluminium bus bars with colour coded heat shrinkable insulating
sleeves

N Outgoing

4000. amps FP electrically operated fully drawout type air circuit breaker with ON/OFF/TRIP
i. indicating lamps with MCB’s and microprocessor based release for protection & indication
as per specification.

1250. amps FP electrically operated fully drawout type air circuit breaker with ON/OFF/TRIP
ii indicating lamps with MCB’s and microprocessor based release for protection & indication
as per specification.

iii 630. amps TPN,50kA, MCCB

iv 630. amps TPN,50kA, MCCB (Spear)

4000. amps FP electrically operated fully drawout type air circuit breaker with ON/OFF/TRIP
v indicating lamps with MCB’s and microprocessor based release for protection & indication
as per specification.(Spear with compartment only)

Notes :

i. All outgoing feeders shall have suitable range of followings (except capacitor feeders)

a. Digital Dual source meter with RS 485/ as per BMS requirement.

b. Digital electronic ammeter with selector switch and 3 Nos. CT’s.

c. Phase indicating light through 230 V, shall be protected by 2 amps SP MCB's.

d. 4. Nos. 630. / 5, 15 VA CT’s shall be provided for APFCR

ii. All breakers shall be electrically/ mechanically interlocked as per schematic diagram.

iii. All MCCB’s shall be suitable for 50. KA (ICS) breaking capacity.

iv. All ACB's shall be suitable for …50kA( Icu=Ics=Icw for 1 sec.)

v. 415 / 110 V suitable rating control transformer shall be provided for aux. Control supply

Wiring with space heater, thermostat and control MCB’s shall be provided all vertical
vi.
sections of main LT panel.

12 of 39
 Erection
SL ITEM DESCRIPTION QTY UNIT
RATE AMOUNT

All outgoing MCCB’s feeders shall be provided with built-in microprocessor release unit
vii.
with earth fault protection and time delay.

viii. All incoming as well as outgoing feeders shall have pad locking facility.

ix. suitable danger board shall be provided.

x. All bus bar section / backside panels shall have pad locking facility and hinged type door.

Main LT Panel as described above. 1 27,500.00 27,500.00

2 Main Common Area Panel

A Incoming

1000. amps, FP electrically operated fully drawout type air circuit breaker with
ON/OFF/TRIP indicating lamps with MCB’s and microprocessor based release for protection
& indication as per specification.

i. Phase indicating light through 230 V, shall be protected by 2 amps SP MCB's.

ii. Breaker ON / OFF / TRIP indicating lights with control MCB’s.

iii. Under voltage release

iv. 24 V DC Shunt trip coil

v Under voltage relay with timer (27)

vi. Over voltage relay with timer (59)

vii. Breaker control switch

3 Nos. 96 x 96 sq.mm 0-1000 / 5 amps CTR digital ammeter with 3 Nos.1000 / 5 amps 15 VA
viii
CL:1 CT’s

0-500 Volt digital voltmeter with selector switch 96 x 96 mm sq. through 415 V / √3 : 110
ix
V /√3 PT’s, Primary and Secondary of PT’s shall be protected by 2 amp TP MCB’s

Class – C, 20KA, TVSS surge arrestor(Lines to Neutral) & (Neutral to Earth) suitable for 3
x
phases, 4 wire.

B Bus Bars

1250. amps 4 pole (50 KA) Aluminium bus bars with colour coded heat shrinkable insulating
i
sleeves

C Outgoing

i 320. amps TPN 36kA MCCB

ii 250. amps FP 25kA MCCB

iii 200. amps TPN 25kA MCCB

iv 160. amps TPN 16kA MCCB

Dual source Load Manager (All Load Managers to have parameters like KW, KVA, A, V,
PF,KVAR, Active & Reactive component of power, as required & desired to complete the
v
system.) with KWH reading for Grid supply. Digital energy meter shall be as per BMS
comunication requirement.

Spare MCCB’s for the following :

vi 320. amps TPN MCCB

13 of 39
 Erection
SL ITEM DESCRIPTION QTY UNIT
RATE AMOUNT

vii 200. amps TPN MCCB

viii 160. amps TPN MCCB

ix 100. amps TPN MCCB

Main Common Area Panel described as above 1 4,400.00 4,400.00

3 Main Fire Emergency Panel

A 1250Amps FP rating Auto Transfer Switch as per specification.

Metering for Grid side & DG side supply.
Phase indicating light through 415 /110 V PT, Primary / Secondary of PT's shall be protected
i.
by 2 amps MCB’s.

3 Nos. 96 x 96 sq.mm 0-1250 / 5 amps CTR digital ammeter with 3 nos 1250 / 5 amps, 15 VA
ii
Class I CT’s.

96 x 96 mm sq. 0-500 Volt digital voltmeter with selector switch through 415 V / Ö3 :
iii
110 V /Ö3 PT’s, Primary and Secondary of PT’s shall be protected by 2 amp TP MCB’s

iv Load Manager conserve EM 6400 with KWH reading for Grid supply

B Incoming
1250. amps 4 pole electrically operated fully drawout type air circuit breaker with
ON/OFF/TRIP indicating lamps with MCB’s and microprocessor based release for protection
& indication as per specification.

i. Phase indicating light through 230 V, shall be protected by 2 amps SP MCB's.

ii. Breaker ON / OFF / TRIP indicating lights with control MCB’s.

iii. Under voltage release

iv. 24 V DC Shunt trip coil

v Under voltage relay with timer (27)

vi. Over voltage relay with timer (59)

vii. Breaker control switch

3 Nos. 96 x 96 sq.mm 0-1250 / 5 amps CTR digital ammeter with 3 Nos.1250 / 5 amps 15 VA
viii
CL:1 CT’s

0-500 Volt digital voltmeter with selector switch 96 x 96 mm sq. through 415 V / √3 : 110
ix
V /√3 PT’s, Primary and Secondary of PT’s shall be protected by 2 amp TP MCB’s

Class – C, 20KA, TVSS surge arrestor(Lines to Neutral) & (Neutral to Earth) suitable for 3
x
phases, 4 wire.

C Bus Bars

1250. amps 4 pole (50 KA) Aluminium bus bars with colour coded heat shrinkable insulating
i
sleeves

D Outgoing

i 630. amps TPN 36kA MCCB

ii 400. amps TPN 36kA MCCB

iii 200. amps TPN 25kA MCCB

iv 160. amps TPN 16kA MCCB

14 of 39
 Erection
SL ITEM DESCRIPTION QTY UNIT
RATE AMOUNT

iv 100. amps TPN 16kA MCCB

v 63. amps TPN 16kA MCCB

Spare MCCB’s for the following :

vi 200. amps TPN MCCB

vii 100. amps TPN MCCB

viii 63. amps TPN MCCB

Main Fire Emergecy Panel described as above 1 6,000.00 6,000.00

4 Main Plumbing Panel

A Incoming
200amps TPN MCCB with following accessories:

0-500 volts digital electronic volt meter with selector switch through 415 V / √3 : 110 V / √3
i.
PT, primary and secondary of PT shall be protected by 2 amps TP MCB's.

0-200 Amps digital electronic ammeter with selector switch and 200/5 amps 15 VA, CL 1
ii.
CTs .

iii. Phase indicating light through 230 V, shall be protected by 2 amps SP MCB's.

iv Load Manager conserve EM 6400 with KWH reading for Grid supply

B Bus Bars

i 250 amps TPN Aluminium bus bars with coloured heat shrinkable insulated sleeve.

C Outgoing

i 125 amps TPN 161kA MCCB

ii 40 amps TPN 10kA MCB

iii 25 amps TP 10kA MCB

iv 25 amps DP 10kA MCB

v 40 amps TPN 10kA MCB ( spare )

vi 25 amps TP 10kA MCB ( spare )

Dual source Load Manager (All Load Managers to have parameters like KW, KVA, A, V,
PF,KVAR, Active & Reactive component of power, as required & desired to complete the
vii
system.) with KWH reading for Grid supply. Digital energy meter shall be as per BMS
comunication requirement.

Main Plumbing Panel As described above 1 1,880.00 1,880.00

5 Main HVAC & Exhaust Panel

A Incoming

320 amps TPN MCCB with following accessories:

0-500 volts digital electronic volt meter with selector switch through 415 V / √3 : 110 V / √3
i.
PT, primary and secondary of PT shall be protected by 2 amps TP MCB's.

15 of 39
 Erection
SL ITEM DESCRIPTION QTY UNIT
RATE AMOUNT
0-320 Amps digital electronic ammeter with selector switch and 320/5 amps 15 VA, CL 1
ii.
CTs .

iii. Phase indicating light through 230 V, shall be protected by 2 amps SP MCB's.

B Bus Bars

i 400 amps FP Aluminium bus bars with coloured heat shrinkable insulated sleeve.

C Outgoing

i 125 amps TPN 16kA MCCB

ii 100 amps TPN 16kA MCCB

iii 63 amps TPN 10kA MCB

iv 25 amps TPN 10kA MCB

v 16 amps TPN 10kA MCB

vi 100 amps TPN 16kA MCCB ( spare )

vii 16 amps TP 10kA MCB ( spare )

Main HVAC & Exhaust Panel As described above 1 3,200.00 3,200.00

6 Elevator Panel-01

A Incoming
320amps TPN MCCB with following accessories:

0-500 volts digital electronic volt meter with selector switch through 415 V / √3 : 110 V / √3
i.
PT, primary and secondary of PT shall be protected by 2 amps TP MCB's.

0-320 Amps digital electronic ammeter with selector switch and 320/5 amps 15 VA, CL 1
ii.
CTs .

iii. Phase indicating light through 230 V, shall be protected by 2 amps SP MCB's.

Class – C, 20KA, TVSS surge arrestor(Lines to Neutral) & (Neutral to Earth) suitable for 3
iv
phases, 4 wire.

B Bus Bars

i 400 amps TPN Aluminium bus bars with coloured heat shrinkable insulated sleeve.

C Outgoing

i 100 amps TP MCCB

ii 100 amps TP MCCB ( spare )

Elevator Panel-01 As described above 1 3,000.00 3,000.00

7 MAIN COMM. AREA LTG.+POWER PANEL(ZONE-1-2)

A Incoming

160 amps TPN MCCB with following accessories:

0-500 volts digital electronic volt meter with selector switch through 415 V / √3 : 110 V / √3
i.
PT, primary and secondary of PT shall be protected by 2 amps TP MCB's.

16 of 39
 Erection
SL ITEM DESCRIPTION QTY UNIT
RATE AMOUNT
0-160 Amps digital electronic ammeter with selector switch and 160/5 amps 15 VA, CL 1
ii.
CTs .

iii. Phase indicating light through 230 V, shall be protected by 2 amps SP MCB's.

B Bus Bars

i 200 amps TPN Aluminium bus bars with coloured heat shrinkable insulated sleeve.

C Outgoing

i 25 amps TPN 10kA MCB

ii 25 amps DP 10kA MCB

iii 25 amps TPN 10kA MCB ( spare )

iv 25 amps DP 10kA MCB ( spare )

MAIN COMM. AREA LTG.+POWER PANEL As described above 2 1,550.00 3,100.00

8 Elevator Panel-02

A Incoming

400amps TPN MCCB with following accessories:

0-500 volts digital electronic volt meter with selector switch through 415 V / √3 : 110 V / √3
i.
PT, primary and secondary of PT shall be protected by 2 amps TP MCB's.

0-400 Amps digital electronic ammeter with selector switch and 400/5 amps 15 VA, CL 1
ii.
CTs .

iii. Phase indicating light through 230 V, shall be protected by 2 amps SP MCB's.

Class – C, 20KA, TVSS surge arrestor(Lines to Neutral) & (Neutral to Earth) suitable for 3
iv
phases, 4 wire.

B Bus Bars

i 500 amps TPN Aluminium bus bars with coloured heat shrinkable insulated sleeve.

C Outgoing

i 100 amps TPN 16kA MCCB

ii 100 amps TPN 16kA MCCB ( spare )

Elevator Panel-02 As described above 1 1,600.00 1,600.00

9 TERRACE- VENTILATION PANEL

A Incoming

200 amps TPN 16kA MCCB with following accessories:

0-500 volts digital electronic volt meter with selector switch through 415 V / √3 : 110 V / √3
i.
PT, primary and secondary of PT shall be protected by 2 amps TP MCB's.

0-200 Amps digital electronic ammeter with selector switch and 200/5 amps 15 VA, CL 1
ii.
CTs .

iii. Phase indicating light through 230 V, shall be protected by 2 amps SP MCB's.

17 of 39
 Erection
SL ITEM DESCRIPTION QTY UNIT
RATE AMOUNT
B Bus Bars

i 250 amps TPN Aluminium bus bars with coloured heat shrinkable insulated sleeve.

C Outgoing

i 63 amps TPN 10kA MCB

ii 40 amps TPN 10kA MCB

iii 25 amps TPN 10kA MCB

iv 16 amps TPN 10kA MCB

v 63 amps TPN 10kA MCB ( spare )

iv 25 amps TPN 10kA MCB ( spare )

TERRACE- VENTILATION PANEL As described above 1 1,870.00 1,870.00

10 PODIUM EMERGENCY VENTILATION PANEL

A Incoming

200amps TPN MCCB with following accessories:

0-500 volts digital electronic volt meter with selector switch through 415 V / √3 : 110 V / √3
i.
PT, primary and secondary of PT shall be protected by 2 amps TP MCB's.

0-200 Amps digital electronic ammeter with selector switch and 200/5 amps 15 VA, CL 1
ii.
CTs .

iii. Phase indicating light through 230 V, shall be protected by 2 amps SP MCB's.

B Bus Bars

i 250 amps TPN Aluminium bus bars with coloured heat shrinkable insulated sleeve.

C Outgoing

i 40 amps TPN MCB

ii 40 amps TPN MCB ( spare )

PODIUM EMERGENCY VENTILATION PANEL As described above 1 1,870.00 1,870.00

11 LT-HT VENTILATION PANEL

A Incoming

63 amps TPN MCCB with following accessories:

0-500 volts digital electronic volt meter with selector switch through 415 V / √3 : 110 V / √3
i.
PT, primary and secondary of PT shall be protected by 2 amps TP MCB's.

ii. 0-63 Amps digital electronic ammeter with selector switch and 63/5 amps 15 VA, CL 1 CTs .

iii. Phase indicating light through 230 V, shall be protected by 2 amps SP MCB's.

B Bus Bars

i 63 amps TPN Aluminium bus bars with coloured heat shrinkable insulated sleeve.

18 of 39
 Erection
SL ITEM DESCRIPTION QTY UNIT
RATE AMOUNT

C Outgoing

i 25 amps TPN MCB

ii 25 amps DP MCB

iii 25 amps TPN MCB ( spare )

LT-HT VENTILATION PANEL As described above 1 1,530.00 1,530.00

12 MAIN COMM. EMER. LTG PANEL

A Incoming

63amps TPN MCCB with following accessories:

0-500 volts digital electronic volt meter with selector switch through 415 V / √3 : 110 V / √3
i.
PT, primary and secondary of PT shall be protected by 2 amps TP MCB's.

ii. 0-63 Amps digital electronic ammeter with selector switch and 63/5 amps 15 VA, CL 1 CTs .

iii. Phase indicating light through 230 V, shall be protected by 2 amps SP MCB's.

B Bus Bars

i 63 amps TPN Aluminium bus bars with coloured heat shrinkable insulated sleeve.

C Outgoing

i 25 amps TPN MCB

ii 25 amps DP MCB

iii 25 amps TPN MCB ( spare )

iv 25 amps DP MCB ( spare )

MAIN COMM. EMER. LTG PANEL As described above 1 1,870.00 1,870.00

13 Ground Floor Panel-1

A Incoming

250 amps TPN MCCB with following accessories:

0-500 volts digital electronic volt meter with selector switch through 415 V / √3 : 110 V / √3
i.
PT, primary and secondary of PT shall be protected by 2 amps TP MCB's.

0-250. Amps digital electronic ammeter with selector switch and 250/5 amps 15 VA, CL 1
ii.
CTs .

iii. Phase indicating light through 230 V, shall be protected by 2 amps SP MCB's.

B Bus Bars

320 amps TPN Aluminium bus bars with colour coded heat shrinkable insulating sleeves

C Outgoing

i. 63 amps TPN MCCB

ii 63 amps TPN MCCB (Spare)

19 of 39
 Erection
SL ITEM DESCRIPTION QTY UNIT
RATE AMOUNT

Dual source Load Manager (All Load Managers to have parameters like KW, KVA, A, V,
PF,KVAR, Active & Reactive component of power, as required & desired to complete the
iii
system.) with KWH reading for Grid supply. Digital energy meter shall be as per BMS
comunication requirement.

Ground Floor Panel-1 As described above 1 5,000.00 5,000.00

14 Ground Floor Panel-2

A Incoming

250 amps TPN MCCB with following accessories:

0-500 volts digital electronic volt meter with selector switch through 415 V / √3 : 110 V / √3
i.
PT, primary and secondary of PT shall be protected by 2 amps TP MCB's.

0-250. Amps digital electronic ammeter with selector switch and 250/5 amps 15 VA, CL 1
ii.
CTs .

iii. Phase indicating light through 230 V, shall be protected by 2 amps SP MCB's.

B Bus Bars

320 amps TPN Aluminium bus bars with colour coded heat shrinkable insulating sleeves

C Outgoing

i. 200 amps TPN 16kA MCCB

ii 100 amps TPN 16kA MCCB

iii 200 amps TPN 16kA MCCB (Spare)

iv 100 amps TPN 16kA MCCB (Spare)

Dual source Load Manager (All Load Managers to have parameters like KW, KVA, A, V,
PF,KVAR, Active & Reactive component of power, as required & desired to complete the
v
system.) with KWH reading for Grid supply. Digital energy meter shall be as per BMS
comunication requirement.

Ground Floor Panel-2 As described above 1 3,950.00 3,950.00

15 Office Meter Panel(1st & 2nd floor) -1

A Incoming

320 amps TPN MCCB with following accessories:

0-500 volts digital electronic volt meter with selector switch through 415 V / √3 : 110 V / √3
i.
PT, primary and secondary of PT shall be protected by 2 amps TP MCB's.

0-320. Amps digital electronic ammeter with selector switch and 320/5 amps 15 VA, CL 1
ii.
CTs .

iii. Phase indicating light through 230 V, shall be protected by 2 amps SP MCB's.

B Bus Bars

400 amps TPN Aluminium bus bars with colour coded heat shrinkable insulating sleeves

C Outgoing

i. 200 amps TPN 16kA MCCB

20 of 39
 Erection
SL ITEM DESCRIPTION QTY UNIT
RATE AMOUNT

ii 160 amps TPN 16kA MCCB

iii 200 amps TPN MCCB (Spare)

iv 160 amps TPN MCCB (Spare)

Dual source Load Manager (All Load Managers to have parameters like KW, KVA, A, V,
PF,KVAR, Active & Reactive component of power, as required & desired to complete the
v
system.) with KWH reading for Grid supply. Digital energy meter shall be as per BMS
comunication requirement.

Office Meter Panel(1st & 2nd floor) -1 As described above 2 3,950.00 7,900.00

16 Office Meter Panel(1st & 2nd floor) -2

A Incoming

320 amps TPN MCCB with following accessories:

0-500 volts digital electronic volt meter with selector switch through 415 V / √3 : 110 V / √3
i.
PT, primary and secondary of PT shall be protected by 2 amps TP MCB's.

0-320. Amps digital electronic ammeter with selector switch and 320/5 amps 15 VA, CL 1
ii.
CTs .

iii. Phase indicating light through 230 V, shall be protected by 2 amps SP MCB's.

B Bus Bars

400 amps TPN Aluminium bus bars with colour coded heat shrinkable insulating sleeves

C Outgoing

i. 250 amps TPN 16kA MCCB

ii 125 amps TPN 16kA MCCB

iii 250 amps TPN MCCB (Spare)

iv 125 amps TPN MCCB (Spare)

Dual source Load Manager (All Load Managers to have parameters like KW, KVA, A, V,
PF,KVAR, Active & Reactive component of power, as required & desired to complete the
v
system.) with KWH reading for Grid supply. Digital energy meter shall be as per BMS
comunication requirement.

Office Meter Panel(1st & 2nd floor) -2 As described above 2 3,950.00 7,900.00

17 Office Meter Panel (3rd,4th,7th & 8th floor) -1

A Incoming

400 amps TPN MCCB with following accessories:

0-500 volts digital electronic volt meter with selector switch through 415 V / √3 : 110 V / √3
i.
PT, primary and secondary of PT shall be protected by 2 amps TP MCB's.

0-400. Amps digital electronic ammeter with selector switch and 400/5 amps 15 VA, CL 1
ii.
CTs .

iii. Phase indicating light through 230 V, shall be protected by 2 amps SP MCB's.

B Bus Bars

21 of 39
 Erection
SL ITEM DESCRIPTION QTY UNIT
RATE AMOUNT
500 amps TPN Aluminium bus bars with colour coded heat shrinkable insulating sleeves

C Outgoing

i. 250 amps TPN 16kA MCCB

ii 200 amps TPN 16kA MCCB

iii 250 amps TPN MCCB (Spare)

iv 200 amps TPN MCCB (Spare)

Dual source Load Manager (All Load Managers to have parameters like KW, KVA, A, V,
PF,KVAR, Active & Reactive component of power, as required & desired to complete the
v
system.) with KWH reading for Grid supply. Digital energy meter shall be as per BMS
comunication requirement.

Office Meter Panel (3rd,4th,7th & 8th floor) -1 As described above 4 3,950.00 15,800.00

18 Office Meter Panel (3rd,5th,9th & 8th floor) -2

A Incoming

400 amps TPN MCCB with following accessories:

0-500 volts digital electronic volt meter with selector switch through 415 V / √3 : 110 V / √3
i.
PT, primary and secondary of PT shall be protected by 2 amps TP MCB's.

0-400. Amps digital electronic ammeter with selector switch and 400/5 amps 15 VA, CL 1
ii.
CTs .

iii. Phase indicating light through 230 V, shall be protected by 2 amps SP MCB's.

B Bus Bars

500 amps TPN Aluminium bus bars with colour coded heat shrinkable insulating sleeves

C Outgoing

i. 250 amps TPN 16kA MCCB

ii 200 amps TPN 16kA MCCB

iii 250 amps TPN MCCB (Spare)

iv 200 amps TPN MCCB (Spare)

Dual source Load Manager (All Load Managers to have parameters like KW, KVA, A, V,
PF,KVAR, Active & Reactive component of power, as required & desired to complete the
v
system.) with KWH reading for Grid supply. Digital energy meter shall be as per BMS
comunication requirement.

Office Meter Panel (3rd,4th,7th & 8th floor) -2 As described above 4 3,500.00 14,000.00

19 Office Meter Panel (5th,6th & 9th floor) -1

A Incoming

400 amps TPN MCCB with following accessories:

0-500 volts digital electronic volt meter with selector switch through 415 V / √3 : 110 V / √3
i.
PT, primary and secondary of PT shall be protected by 2 amps TP MCB's.

22 of 39
 Erection
SL ITEM DESCRIPTION QTY UNIT
RATE AMOUNT
0-400. Amps digital electronic ammeter with selector switch and 400/5 amps 15 VA, CL 1
ii.
CTs .

iii. Phase indicating light through 230 V, shall be protected by 2 amps SP MCB's.

B Bus Bars

500 amps TPN Aluminium bus bars with colour coded heat shrinkable insulating sleeves

C Outgoing

i. 250 amps TPN 16kA MCCB

ii 200 amps TPN 16kA MCCB

iii 250 amps TPN MCCB (Spare)

iv 200 amps TPN MCCB (Spare)

Dual source Load Manager (All Load Managers to have parameters like KW, KVA, A, V,
PF,KVAR, Active & Reactive component of power, as required & desired to complete the
v
system.) with KWH reading for Grid supply. Digital energy meter shall be as per BMS
comunication requirement.

Office Meter Panel (5th,6th & 9th floor) -1 As described above 3 3,950.00 11,850.00

20 Office Meter Panel (5th,6th& 9th floor)-2

A Incoming

400 amps TPN MCCB with following accessories:

0-500 volts digital electronic volt meter with selector switch through 415 V / √3 : 110 V / √3
i.
PT, primary and secondary of PT shall be protected by 2 amps TP MCB's.

0-400. Amps digital electronic ammeter with selector switch and 400/5 amps 15 VA, CL 1
ii.
CTs .

iii. Phase indicating light through 230 V, shall be protected by 2 amps SP MCB's.

B Bus Bars

500 amps TPN Aluminium bus bars with colour coded heat shrinkable insulating sleeves

C Outgoing

i. 200 amps TPN 16kA MCCB

ii 200 amps TPN MCCB (Spare)

Dual source Load Manager (All Load Managers to have parameters like KW, KVA, A, V,
PF,KVAR, Active & Reactive component of power, as required & desired to complete the
iii
system.) with KWH reading for Grid supply. Digital energy meter shall be as per BMS
comunication requirement.

Office Meter Panel (5th,6th & 9th floor) -2 As described above 3 3,950.00 11,850.00

21 Office Meter Panel (10th floor) -1

A Incoming

400 amps TPN MCCB with following accessories:

23 of 39
 Erection
SL ITEM DESCRIPTION QTY UNIT
RATE AMOUNT
0-500 volts digital electronic volt meter with selector switch through 415 V / √3 : 110 V / √3
i.
PT, primary and secondary of PT shall be protected by 2 amps TP MCB's.

0-400. Amps digital electronic ammeter with selector switch and 400/5 amps 15 VA, CL 1
ii.
CTs .

iii. Phase indicating light through 230 V, shall be protected by 2 amps SP MCB's.

B Bus Bars

500 amps TPN Aluminium bus bars with colour coded heat shrinkable insulating sleeves

C Outgoing

i. 250 amps TPN 25 kA MCCB

ii 160 amps TPN 16kA MCCB

iii 250 amps TPN MCCB (Spare)

iv 160 amps TPN MCCB (Spare)

Dual source Load Manager (All Load Managers to have parameters like KW, KVA, A, V,
PF,KVAR, Active & Reactive component of power, as required & desired to complete the
v
system.) with KWH reading for Grid supply. Digital energy meter shall be as per BMS
comunication requirement.

Office Meter Panel ( 10th floor) -1 As described above 1 3,950.00 3,950.00

22 Office Meter Panel (10th floor) -2

A Incoming

400 amps TPN MCCB with following accessories:

0-500 volts digital electronic volt meter with selector switch through 415 V / √3 : 110 V / √3
i.
PT, primary and secondary of PT shall be protected by 2 amps TP MCB's.

0-400. Amps digital electronic ammeter with selector switch and 400/5 amps 15 VA, CL 1
ii.
CTs .

iii. Phase indicating light through 230 V, shall be protected by 2 amps SP MCB's.

B Bus Bars

500 amps TPN Aluminium bus bars with colour coded heat shrinkable insulating sleeves

C Outgoing

i. 200 amps TPN 16kA MCCB

ii 160 amps TPN 16kA MCCB

iii 200 amps TPN MCCB (Spare)

iv 160 amps TPN MCCB (Spare)

Dual source Load Manager (All Load Managers to have parameters like KW, KVA, A, V,
PF,KVAR, Active & Reactive component of power, as required & desired to complete the
v
system.) with KWH reading for Grid supply. Digital energy meter shall be as per BMS
comunication requirement.

Office Meter Panel ( 10th floor) -2 As described above 1 3,950.00 3,950.00

24 of 39
 Erection
SL ITEM DESCRIPTION QTY UNIT
RATE AMOUNT

23 CONTROL PANEL FOR FIRE PUMPS IN PUMP ROOM

Supply, installation, testing & commissioning of panel for Electrical motor driven pumps.

INCOMING:
1000. amps 4 pole electrically operated fully drawout type air circuit breaker with
ON/OFF/TRIP indicating lamps with MCB’s and microprocessor based release for protection
& indication as per specification.
BUSBAR:
1000 Amps, Al Busbars continuous duty,FP with heat shrinkable sleeves, supported on
SMC supports Of 50 KA design.
ON,OFF,TRIP Indication Lamps -3 No's - 1 set
LED Type R - Y - B Phase Indicating Lamps -3 No's - 1 set
2A, MCB's - 2 Nos.
0-1000 Amps Ammeter with selector switch - 1 set
1 No. 0-500V Voltmeter with selector switch-1 set
CT of ratio 1000/5A accuracy class 0.5 - 1 No.
OUTGOING:
FOR MAIN PUMPS - 2 NOS.
Star delta Starter Suitable for Rating of Pumps. Contactor to submit Coordination chart of
the proposed make. Contractor to consider on size higher for Starter- 2 Nos.
Auto manual selector switch - 2 Nos.

FEEDER FOR JOCKEY PUMPS - 1 NO.

DOL Starter Suitable for Rating of Pumps. Contactor to submit Coordination chart of the
proposed make. Contractor to consider on size higher for Starter - 1 Nos.

FEEDER FOR BOOSTER PUMPS

DOL Starter Suitable for Rating of Pumps. Contactor to submit Coordination chart of the
proposed make. Contractor to consider on size higher for Starter - 1 Nos.
Push Button on Ground Floor for Emergency Start of the Booster Pump.
Required control cable from the Booster Pump Starter Panel to the Push button Station on
Ground Floor.
Starter Selection to be as Type 2 Co-ordination Charts. Vendor to consider the size of the
breakers, contactors, relays as per the selected make and submit the selection chart for
approval to consultants.
Also panel shall have sufficient NO/NC contacts for extending the status (Annunciation) of
fire pumps to the Fire Alarm Panel and also have relevant provisions for FAS/ BMS
interlocking.

CONTROL PANEL FOR FIRE PUMPS As described above 1

25 Bus Duct (In sandwich Construction)

Design, manufacturer, supply, installation, testing and commissioning of 4000. amps rating
(50 KA for 1 Sec)busduct in sandwich construction of aluminium bus bars with expansion
i
joints, (IP52). Bus duct shall be conforming to fully type tested with relevent testing agency.
Bus duct shall be conforming to IEC-61439-6.

Fire barriers including necessary supports and louvers for ventilation, fabricated out of
extruded aluminium/ GI sheet painted with approved paint shade as per specification
including 2 Nos. of 50x6 mm copper earthing conductor through out the length of the bus
duct. (Phase sequence shall be matched).( end connection of each length should be copper
tips )

4000.. amps 4 pole bus ducts from Main LT Panel to Rising main including 90 deg bends &
a 530 RM 1,950.00 1,033,500.00
flanges to connect LT panel.

b Flexible end connection on LT panel side of 4000A 12 No. 750.00 9,000.00

Supply, installation, testing and commissioning of tap off boxes made out of 14 gauge CRCA
sheet steel in case of Air Insulated Rising Mains & extruded Aluminium/ GI sheet duly
26
painted in case of sandwich type Rising Mains mounted on the rising mains including
providing of following MCCB’s.

25 of 39
 Erection
SL ITEM DESCRIPTION QTY UNIT
RATE AMOUNT

a 400 amps TPN Pole MCCB of 36 KA (Ics). 16 No. 634.00 10,144.00

b 320 amps TPN Pole MCCB of 36 KA (Ics). 4 No. 525.00 2,100.00

c 250 amps TPN Pole MCCB of 36 KA (Ics). 2 No. 450.00 900.00

Supply, Installation, Testing & Commissioning of Circuit Breakers enclosed in a fabricated

27 Powder Coated G.I. OR MS enclosure as per specifications complete with all necessary
accessories required to complete the job including structural supports.

a 400 amps TPN Pole MCCB of 36 KA (Ics). with MS Enclosure No. 434.00 -

b 320 amps TPN Pole MCCB of 36 KA (Ics). with MS Enclosure No. 325.00 -

a 250 amps TPN Pole MCCB of 25 KA (Ics). with MS Enclosure 14 No. 265.00 3,710.00

b 200 amps TPN Pole MCCB of 16 KA (Ics). with MS Enclosure 20 No. 180.00 3,600.00

c 160 amps TPN Pole MCCB of 16 KA (Ics). with MS Enclosure 4 No. 180.00 720.00

d 125 amps TPN Pole MCCB of 16 KA (Ics). with MS Enclosure 3 No. 135.00 405.00

e 100 amps TPN Pole MCCB of 16 KA (Ics). with MS Enclosure 4 No. 90.00 360.00

f 63 amps TPN Pole MCCB of 16 KA (Ics). with MS Enclosure 6 No. 90.00 540.00

g 63 amps TPN Pole MCB of 10 KA (Ics). with MS Enclosure 4 No. 90.00 360.00

h 40 amps TPN Pole MCB of 10 KA (Ics). with MS Enclosure 13 No. 90.00 1,170.00

40 amps TPN Pole MCB of 10 KA (Ics). with MS Enclosure & star-delta Starter Suitable for
i 3 No. 90.00 270.00
Rating of Pumps. Contactor to submit Coordination chart of the proposed make.

j 25 amps TPN Pole MCB of 10 KA (Ics). with MS Enclosure 22 No. 90.00 1,980.00

25 amps TPN Pole MCB of 10 KA (Ics). with MS Enclosure & DOL Starter Suitable for Rating
k 2 No. 90.00 180.00
of Pumps. Contactor to submit Coordination chart of the proposed make.

l 16 amps TPN Pole MCB of 10 KA (Ics). with MS Enclosure 6 No. 90.00 540.00

Supply, installation, testing and commissioning of Auto Transfer Switch with encloser out of
28
14 gauge CRCA sheet steel providing of following ATS’s.

400Amps FP rating Auto Transfer Switch/ Contactor Logic for change over as per
a NO. 3,200.00 -
specification.

320Amps FP rating Auto Transfer Switch/ Contactor Logic for change over as per
b NO. 3,000.00 -
specification.

250Amps FP rating Auto Transfer Switch/ Contactor Logic for change over as per
c NO. 2,400.00 -
specification.

29 FINAL DISTRIBUTION BOARDS

Supply, installation, testing and commissioning of the following FDB's fabricated out of 1.6
mm thick CRCA sheet steel , double door construction, powder coated with approved
shade and partitions to segregate phases. Approved lockable covers with padlocking
arrangement for each phase, recessed in wall or surface mounted final distribution boards
of the following description:

26 of 39
 Erection
SL ITEM DESCRIPTION QTY UNIT
RATE AMOUNT
Class - C (For SPN final distribution boards) (lines to Neutral) (Neutral to earth) suitable for
1 Phase as per specification and Class - C (For TPN final distribution boards) (lines to
Neutral) (Neutral to earth) suitable for 3 Phase as per specification

1 12 WAY VTPN DB - TERRACE HVAC VTPN DB

A Incoming
125 amps TPN Pole MCCB of 16 KA (Ics).

B Outgoing
i 32 amps TP MCB with following accessories:

ii 25 amps TP MCB with following accessories:

iii 32 amps TP MCB with following accessories:

iv 25 amps TP MCB with following accessories:

All MCB's shall be of …10.. KA (Ics) breaking capacity.

VTPN 12 WAY DB - TERRACE HVAC VTPN DB As described above 1 1,100.00 1,100.00

2 SUB ELEVATOR DB
A Incoming
63 amps TPN Pole MCCB of 16 KA (Ics).

B Outgoing
i 63 amps FP ELCB,300mA with following accessories:

ii 16 amps SP MCB with following accessories:

iii 10 amps SP MCB with following accessories:

All MCB's shall be of …10.. KA (Ics) breaking capacity.

SUB ELEVATOR DB As described above 18 1,000.00 18,000.00

3 12 WAY TPN LDB1 & LDB2-BASEMENT 1,2, LG & Ground Floor

A Incoming
25 amps TPN MCB with following accessories:

B SUB Incoming
25 amps DP RCCB, 30mA -
25A, DP Contactor with (0-24 Hr) timer

C Outgoing
i 10. amps SP MCB

ii 10. amps SP MCB (Spare)

All MCCB's shall be of …10.. KA (Ics) breaking capacity.

12 WAY TPN LDB1 & LDB2-BASEMENT 1,2,LG Floor As described above 8 1,100.00 8,800.00

4 8 WAY TPN STAIRCASE DB

A Incoming
25 amps TPN MCB with following accessories:

B SUB Incoming
25 amps DP RCCB, 30mA -
25A, FP Contactor with (0-24 Hr) timer

C Outgoing
i 10. amps SP MCB

ii 10. amps SP MCB (Spare)

All MCB's shall be of …10.. KA (Ics) breaking capacity.

27 of 39
 Erection
SL ITEM DESCRIPTION QTY UNIT
RATE AMOUNT

8 WAY TPN STAIRCASE DB As described above 1 1,000.00 1,000.00

5 8 WAY TPN STAIRCASE EDB

A Incoming
25 amps TPN MCB with following accessories:

B SUB Incoming
25 amps DP RCCB, 30mA -
25A, FP Contactor with (0-24 Hr) timer

C Outgoing
i 10. amps SP MCB

ii 10. amps SP MCB (Spare)

All MCB's shall be of …10.. KA (Ics) breaking capacity.

8 WAY TPN STAIRCASE EDB As described above 1 1,000.00 1,000.00

6 12 WAY TPN LIFT LOBBY DB (BASEMENT-2 TO P6 FLOOR)

A Incoming
25 amps TPN MCB with following accessories:

B SUB Incoming
25 amps DP RCCB, 30mA -
25A, DP Contactor with (0-24 Hr) timer

C Outgoing
i 10. amps SP MCB

ii 10. amps SP MCB (Spare)

All MCB's shall be of …10.. KA (Ics) breaking capacity.

12 WAY TPN LIFT LOBBY DB (BASEMENT-2 TO P6 FLOOR) As described above 1 1,100.00 1,100.00

7 8 WAY TPN LDB3 Ground floor

A Incoming
25 amps TPN MCB with following accessories:

B SUB Incoming
25 amps DP RCCB, 30mA -

C Outgoing
i 16. amps SP MCB

ii 10. amps SP MCB

All MCB's shall be of …10.. KA (Ics) breaking capacity.

8 WAY TPN LDB3 Ground floor As described above 1 950.00 950.00

8 12 WAY TPN LDB1 & LDB2-Podiums-1,2,3,4,5,6,7

A Incoming
25 amps TPN MCB with following accessories:

B SUB Incoming
25 amps DP RCCB, 30mA -
25A, DP Contactor with (0-24 Hr) timer

C Outgoing
i 10. amps SP MCB

All MCB's shall be of …10.. KA (Ics) breaking capacity.

12 WAY TPN LDB1 & LDB2 - Podiums - 1,2,3,4,5,6,7 As described above 14 1,100.00 15,400.00

28 of 39
 Erection
SL ITEM DESCRIPTION QTY UNIT
RATE AMOUNT
9 12 WAY TPN LDB1 & LDB3-1st to 5th Lift Lobby & passage
A Incoming
25 amps TPN MCB with following accessories:

B SUB Incoming
25 amps DP RCCB, 30mA -
25A, DP Contactor with (0-24 Hr) timer

C Outgoing
i 10. amps SP MCB

All MCB's shall be of …10.. KA (Ics) breaking capacity.

12 WAY TPN LDB1 & LDB3-1st to 5th Lift Lobby & passage As described above 2 1,100.00 2,200.00

10 12 WAY TPN LDB2 & LDB4-6th to 10th common Area

A Incoming
25 amps TPN MCB with following accessories:

B SUB Incoming
25 amps DP RCCB, 30mA -
25A, DP Contactor with (0-24 Hr) timer

C Outgoing
i 10. amps SP MCB

All MCB's shall be of …10.. KA (Ics) breaking capacity.

12 WAY TPN LDB2 & LDB4- 12 WAY 6th to 10th common Area As described above 2 1,100.00 2,200.00

11 8 WAY TPN - LDB6 PARKING AREA (PMC UNDER) Lower Ground

A Incoming
25 amps FP RCBO, 30mA - following accessories:

B SUB Incoming
25 amps DP RCCB, 30mA -

C Outgoing
i 10. amps SP MCB

All MCB's shall be of …10.. KA (Ics) breaking capacity.

8 WAY TPN -LDB6 PARKING AREA (PMC UNDER) Lower Ground As described above 1 950.00 950.00

12 8 WAY TPN - LDB1 Terrace Floor

A Incoming
25 amps FP RCBO, 30mA - following accessories:

C Outgoing
i 16. amps SP MCB

ii 10. amps SP MCB

All MCB's shall be of …10.. KA (Ics) breaking capacity.

8 WAY TPN - LDB1 Terrace Floor As described above 1 1,000.00 1,000.00

13 8 WAY SPN LDB3 & LDB4 BASEMENT 2, Lower Ground & LDB3 Ground floor
A Incoming
40 amps DP RCBO,30mA with following accessories:

B Outgoing
i 16. amps SP MCB

ii 10. amps SP MCB

29 of 39
 Erection
SL ITEM DESCRIPTION QTY UNIT
RATE AMOUNT
All MCB's shall be of …10.. KA (Ics) breaking capacity.

8 WAY SPN LDB3 & LDB4 BASEMENT 2, Lower Ground & LDB3 Ground floor As described
5 900.00 4,500.00
above

14 12 WAY SPN LDB3 & LDB4 BASEMENT 1 & LDB4 Ground floor
A Incoming
40 amps DP RCBO,30mA with following accessories:

B Outgoing
i 16. amps SP MCB

ii 10. amps SP MCB

All MCB's shall be of …10.. KA (Ics) breaking capacity.

12 WAY SPN LDB3 & LDB4 - BASEMENT 1 LDB4 Ground floor As described above 3 900.00 2,700.00

15 SPN 8 WAY LDB1 & LDB2-Office Floor(1st to 10th)

A Incoming
25 amps DP RCBO with following accessories:

B Outgoing
i 16. amps SP MCB

ii 10. amps SP MCB

All MCB's shall be of …10.. KA (Ics) breaking capacity.

SPN 8 WAY LDB1 & LDB2-Office Floor(1st to 10th) As described above 20 700.00 14,000.00

16 8 WAY SPN LDB3 & LDB4 Podiums-1,2,3,4,5,6,7

A Incoming
25 amps DP RCBO,30mA with following accessories:

B Outgoing
i 16. amps SP MCB

ii 10. amps SP MCB

All MCCB's shall be of …10.. KA (Ics) breaking capacity.

8 WAY SPN LDB3 Podiums-1,2,3,4,5,6,7 As described above 14 700.00 9,800.00

17 12 WAY SPN ELDB1 & ELDB2 BASEMENT 1, 2 & ELDB2 Ground Floor
A Incoming
16 amps DP RCBO with following accessories:

B Outgoing
i 10. amps SP MCB

All MCB's shall be of …10.. KA (Ics) breaking capacity.

12 WAY SPN ELDB1 & ELDB2-BASEMENT 1, 2, LG As described above 3 950.00 2,850.00

18 8 WAY SPN ELDB1 & ELDB3 LG & ELDB1 GF

A Incoming
40 amps DP RCBO,30mA with following accessories:

B Outgoing
i 16. amps SP MCB

ii 10. amps SP MCB

All MCCB's shall be of …10.. KA (Ics) breaking capacity.

8 WAY SPN ELDB1 & ELDB3 LG & ELDB1 GF As described above 3 700.00 2,100.00

30 of 39
 Erection
SL ITEM DESCRIPTION QTY UNIT
RATE AMOUNT
19 12 WAY SPN LIFT LOBBY EDB2 BASEMENT-2 TO P6 FLOOR
A Incoming
16 amps DP RCBO with following accessories:

B Outgoing
i 10. amps SP MCB

All MCB's shall be of …10.. KA (Ics) breaking capacity.

12 WAY SPN LIFT LOBBY EDB2 BASEMENT-2 TO P6 FLOOR As described above 1 700.00 700.00

20 6 WAY SPN ELDB4 Lower Ground

Incoming
25 amps DP RCBO,30mA with following accessories:

Outgoing
10. amps SP MCB

All MCB's shall be of …10.. KA (Ics) breaking capacity.

6 WAY SPN ELDB4 Lower Ground As described above 1 700.00 700.00

21 8 WAY SPN ELDB1 & ELDB2 -PODIUM 1,2,3,4,5,6 & 7

A Incoming
16 amps DP RCBO with following accessories:

B Outgoing
i 10. amps SP MCB

All MCB's shall be of …10.. KA (Ics) breaking capacity.

SPN 8 WAY ELDB1 & ELDB2 -PODIUM 1,2,3,4,5,6 & 7 As described above 14 700.00 9,800.00

22 12 WAY SPN ELDB-1 For (1st to10th) Floor

A Incoming
25 amps DP RCBO with following accessories:

B Outgoing
i 10. amps SP MCB

ii 20 amps SP MCB

All MCB's shall be of …10.. KA (Ics) breaking capacity.

SPN 12 WAY ELDB-1 For (1st to10th) floor As described above 5 700.00 3,500.00

TOTAL CARRIED TO SUMMARY 1,317,799.00

D. CAPACITOR BANKS WITH DETUNED FILTER IN AUTOMATIC CONTROL UNITS

The rates for the capacitor bank panels apart from the switches and instruments shall also
include
the following :

1 Supporting rigid steel framework.

2 Cubicle type, 14 gauge CRCA sheet steel enclosed.

3 Complete with interconnections and distribution bus bars.

4 Proper bonding to earth.

5 Providing cable clamps/supports within panels cable alley.

The breaking capacity of MCCB’s/ ACB's are mentioned panel wise. MCCB’s/ ACB's shall
6
be
with thermal magnetic releases.

31 of 39
 Erection
SL ITEM DESCRIPTION QTY UNIT
RATE AMOUNT
Rubber mats shall be provided in front of all panels and the back where they are accessable
7
from
the back as per IS 15652-2006.

Automatic capacitor control panels shall be powder coated with Siemens Grey RAL 7032 of
8
IS-5.

9 Enclosure of all capacitor control panel shall be as per IS 13947-1993.

10 All MCCB / ACB shall be provided with operating mechanism for door interlock.

Current density of aluminium shall be 1 sq mm for 1.0 amps for rated current of bus bars
11
current
density of copper shall be 1 sq.mm for 1.25 amps of rated current of bus bars.

12 TPN MCCB shall means 3 pole MCCB with adequate size of neutral link.

13 All copper bus bars shall be factory tinned.

14 Tinned copper / GI earth bus shall be provided through out the length of each panel.

15 All hinged door shall be earthed through 2.5 sq.mm tinned braided copper wire.

16 All PT’s / Control transformer shall be provided with centre tap earth secondary.

17 All incoming and outgoing feeders have Pad locking facility.

18 All bus bars section / backside panels shall have pad locking facility and hinged type doors.

19 All steps of capacitor unit shall be connected with super fast electronic fuse.

20 All capacitor unit shall be connected with fast discharge resistances.

21 All capacitor unit shall be switched by means of thyristor switching module.

22 All capacitor shall be connected in series with 5.67% detuned filter.

23 Capacitor rating shall be suitably increased considering filter.

D. CAPACITOR BANKS WITH DETUNED FILTER IN AUTOMATIC CONTROL UNITS

Design, fabrication, assembling, wiring, supply, installation, testing and commissioning of

Automatic control panels with low loss APP type capacitors, fabricated out of 14 gauge
CRCA sheet steel in cubicle compartmentised, free standing, floor mounted, dust and
vermin proof with reinforcement of suitable size, angle iron, channel, ‘T’ sections and /
or flats wherever necessary. Cable gland plates shall be provided on top as well as at the
bottom of the panels. Panels shall be treated with all anticorrosive process before powder
coating as per specifications and final approved shade. 2 Nos. earthing terminals shall be
provided for all distrtibution panels. Panels shall be suitable for 415V, 3 phase, 4 wire, 50
HZ supply system. Lifting hooks shall also be provided in case of large panels. Approval
shall be taken for each panel in the form of shop drawings before fabrication. Galvanised
hardwares with zinc passivation shall be used in fabrication of panels. The system shall be
provided with

It shall provide rated 25/20/10/5 KVAR in suitable nos. of steps & of suitable rating of
capacitors ( 12steps for above 360 kVAR bank), as per specification. The panel shall also
comply with following :

630 Amps TP Manual drawout type MCCB incomer with 50_KA breaking capacity to be
1
provided :

32 of 39
 Erection
SL ITEM DESCRIPTION QTY UNIT
RATE AMOUNT

Microprocessor APFC controller shall continuously monitor all three phases and displays
various Electrical Parameters like voltage, input current, capacitive current, KVA
demand,KW, Power Factor, self diagnostic error code indication with printout facility of the
2
above with RS 232C port. Controller should mounted on the front side of the panel. It shall
have data logging for minimum 2 months, it shall provide thyristor output for maximum 16
stages.

3 Fast response time of ‘ON’ capacitors 20-60 miliseconds.

MCCBs of the proper rating to be used for grouping the capacitor banks. Capacitor shall be
4
connected with fast discharge resistances.

5 Thyristor having suitable capacity to carry expected current continuosly.

Necessary control and firing card with proper wiring and lugs of the required rating to be
6
provided.

7 Heavy duty exhaust fans to be provided for cooling Thyristors.

8 LED indication for number of capacitor banks ‘ON’.

9 LED indication of Power Factor lagging or leading.

Auto/manual selector switch with necessary wiring to operate APFC panel in manual mode
10
bypassing APFC relay.

11 The APFC system shall be provided with following :

Protections :

a. Over voltage.

b. Voltage imbalance.

Over temperature-system should be in standby mode and automatically restart after above
c.
condition restored.

d. Total Harmonic Distortion

11 7% of series reactor having linearity as (2.08). €In with L=0.95Ln

Capacitor Units shall have 480 V and rating shall be suitably increased considering reactors
12
into account.

Capacitor automatic control panel (350 KVAR)

as described above. 4 Sets 5,000.00 20,000.00
TOTAL CARRIED TO SUMMARY 20,000.00

E. EARTHING INSTALLATION (FOR POWER DISTRIBUTION SYSTEMS,

LIFTS, LT PANELS,UPS SYSTEM & EPABX

Rates shall also include the following :

This schedule of Quantities shall be read in conjuction with the technical specification,
1
General & Special conditions as well as all tender drawings.

2 All fixing accessories such as saddles, screws rawl plugs etc.

Jointing by rivetting and brazing after rivetting in case of copper and welding / bolting in
case
3 of GI earthing.

4 Cutting chases / holes and making good the same wherever required.

5 Effecting adequate and proper interconnections.

6 Use of copper thimbles.

33 of 39
 Erection
SL ITEM DESCRIPTION QTY UNIT
RATE AMOUNT

7 Earthing system shall comply to IS:3043-1987.

8 All earthing pits shall be interconnected.

All equipment motors, DB’s, panels to be connected on both ends (double earthing) with
suitable
9 strip / wires.

10 Soil resistingly test shall be conducted of the area where earth pits are to be located.

E. EARTHING INSTALLATION (FOR POWER DISTRIBUTION SYSTEMS & UPS SYSTEM

Supply and fixing of following bare copper /GI tapes / wires including all necessary fixing
1
accessories and effecting connections as per specifications.

1.1 50 x 10 mm thick GI tape. 30 RM 50.00 1,500.00

1.2 50 x 6 mm thick GI tape. 286 RM 44.00 12,584.00

1.3 32 x 6 mm thick GI tape. 205 RM 34.00 6,970.00

1.4 25 x 3 mm thick GI tape. 5760 RM 25.00 144,000.00

1.5 50 x 6 mm thick CU tape. RM 50.00 -

1.6 8 SWG GI wire 850 RM 4.00 3,400.00

6 Maintenance free earthing electrode / chemical earthing (Alternate-II)

Providing and laying of 14.35 mm dia and 3 meter length.copper bonded earth rod in 150
mm dia. in an augured hole in ground , surrounded by ground enhancement material as per
specification. Inspection chamber shall be of 400 x 500 mm with concrete base CI manhole
cover with frame painted with bitumastic paint. 2 Nos. of 50 x 6 mm cross section & 300
6.1 mm long copper strip to be clamped with copper claded rod electrode have sufficient nos ( 46 Nos. 4,500.00 207,000.00
But not less than 4 Nos.) of 10 mm dia. GI nuts & bolts for connection to the equipment /
interconnection to the other pits to form equi-potential bonding .The pH value of ground
enhance material shall be 6.9 to 7.2 of 1000gm / lit @ 20 deg.c.The minimum 30 Kg of
ground enhancement material shall provided for each electrode.

Providing earthing stations at locations as called for including providing and laying 600 x
600 x 3.15 mm thick tinned copper electrode with 2 Nos 50 x 6 mm thick copper strip,
from earth electrode to inspection chamber,50 mm dia medium class G I pipe CI /
chequered plate funnel with 20 gauge G I wire mesh, masonry chamber 1000 x 500 mm
Nos. 4,000.00 -
with concrete base, CI chequered plate manhole cover with frame and bitumastic paint
and packing of mixture of charcoal and common salt around plate electrode complete
with digging of pit upto permanent misture level but not less than 3 metres and back filling
as required.

Supply and installation of 50 x 6 mm Cu busbar mounted on insulators and having 6 nos.

holes for terminating single core 35 Sq.mm flexible cable with the entire assembly enclosed
7 Nos. 350.00 -
in 1.6 mm thick MS enclosure of approved make, design & painted with approved paint
shade. (for UPS/low volt earthing and installed in electrical shaft).

TOTAL CARRIED TO SUMMARY 375,454.00

F. LIGHTNING PROTECTION SYSTEM

Rates shall also include the following :

This schedule of Quantities shall be read in conjuction with the technical specification,
1
General & Special conditions as well as all tender drawings.

2 All fixing accessories such as brass saddles, brass screws rawl plugs etc.

34 of 39
 Erection
SL ITEM DESCRIPTION QTY UNIT
RATE AMOUNT

Jointing by rivetting and brazing after rivetting in case of copper and by welding / bolting
3
in case of GI.

4 Cutting chases, holes and making good the same wherever required.

5 Effecting adequate and proper interconnections.

6 Use of copper thimbles.

7 Lightning protection system shall comply to IS 62305

8 All earthing pits shall be interconnected.

F. LIGHTNING PROTECTION SYSTEMS

SUPPLY, INSTALLATION, TESTING AND COMISSIONING OF LIGHTENING PROTECTION

SYSTEM
Air Terminal
Supply of 8 mm Aluminum Round Conductor complete as specified in drawing & Meets the
1 requirements of DIN EN 50164-2 (VDE 0185 part 202) & VDE 0185-305 (IS/IEC 980 Mtr 18.00 17,640.00
62305) , OBO Type No. RD 8/ALU (5021 28 6)

Supply of Roof conductor holder for parapet- Polyamide Conductor holder:

With M8 female thread or diameter 7mm, M8 Screw to connect the conductor holder.
2 396 Nos 35.00 13,860.00
Weather and temperature resistant from -35 to +90 degree Celsius tested. Conductor
holder @ 1 meter distance OBO Type No. 177 30 M8(5207 46 0 )

Polyamide roof cable holder for flat roof:

DIN 48829 Form B1. Closed form with bottom. Filling weight 1Kg (frost-resistant concrete).
3 518 Nos 35.00 18,130.00
Sleeve from polyethylene, black @ 1 meter distance. OBO Type No. 165 MBG-8 ( 5218
69 1 )
Vertical air terminal with accessories:Providing of Air terminals as per IS-IEC -62305 part-3
16mm rod tapered to 10 mm aluminium rod :
4 4 Nos 180.00 720.00
Meets the technical specification according to DIN EN 50164- 2 (VDE 0815 part 202).
Meets the requirement of VDE0185/305(IS/IEC 62305)

3Mtr Airterminal: semi-hard (E-AlMgSiO5 corresponds to DIN 48801) Suitable for high wind
5 load. OBO Type No. 101 VL3000 ( 5401 98 9 ). 4 Nos 54.00 216.00

Accessories : System consist of Fang Fix with base and clamp, on the top air terminal is
erected. OBO Type No. F- FIX 16 ( 5403 20 0 ).
Fang fix clamp made of SS, lightning tested for 100 KA 10/350 micro sec waveform.
6 4 Nos 135.00 540.00
16 KG stone of 365 mm diameter, high level of stability. Quick and easy mounting of
interception rod using anchors. Concrete, frost-resistant, can be stacked.OBO Type No. F-
FIX S16 ( 5403 22 7 )

Providing of cross universal connector: For T and cross connection, to route vertical down
conductor /mesh formation made of hot dipped galvanised iron with necessary screws etc
7 55 Nos 70.00 3,850.00
as required. Installed with 4 hexagonal bolts M8*25 with M8 hexagonal nuts . OBO Type
No.251 8- 10 ( 5312 03 5 )
Providing of expansion piece with connector: For equalising temperature related length
changes. Necessary on conductors length over 20 meters. For round conductor Rd 8/ALU.
8 39 Nos 40.00 1,560.00
OBO Type No. 172 AR ( 5218 92 6 )

Connector: For T cross and parallel connectors. Quick installation using hexagonal bolt
M10X30 high-grade hot dip galvanised. Conforms to the requirements according to DIN
9 78 Nos 40.00 3,120.00
VDE 0185-305 (IS-IEC 62305)(2nos/expansion piece ). OBO Type No. 249 8-10 ST ( 5311 50 0
)
Providing of Bridging cable: From flexible CU cable of
16mm2 with black colur coating, chlorinated India rubber
10 mixture .Exclusively used for indoor & outdoor application to 10 Nos 40.00 400.00
make continuity at terminals.OBO Type No. 853 300 ( 5331
01 3)

Down Conductor

35 of 39
 Erection
SL ITEM DESCRIPTION QTY UNIT
RATE AMOUNT
Supply of 8 mm Aluminum Round Conductor complete as specified in drawing & Meets the
11 requirements of DIN EN 50164-2 (VDE 0185 part 202) & VDE 0185-305 (IS/IEC 1570 Mtr 18.00 28,260.00
62305) , OBO Type No. RD 8/ALU (5021 28 6 )

Supply of Roof conductor holder for parapet- Polyamide Conductor holder:

With M8 female thread or diameter 7mm, M8 Screw to connect the conductor holder.
12 1570 Nos 35.00 54,950.00
Weather and temperature resistant from -35 to +90 degree Celsius tested. Conductor
holder @ 1 meter distance OBO Type No. 177 30 M8 (5207 46 0 )

Supply of Test Joint (Folding Clamp) suitable to connect 8mm round conductor and max by
13 30x3 mm GI strip as specified in drawing and directed by Engineer OBO Type No. 271 8-10 22 Nos 40.00 880.00
( 5317 40 1 )

Lightnig counter - To count no of lightning strike & it can record the date and time of the
14 1 Nos 350.00 350.00
lightning incident also tested as per IEC 62561-6. OBO Type No. LSC I+II ( 5091 72 2 )
Earthing

Supply of Galvanised Steel Flat 30X3 mm thickness from earth electrode directly in ground
as required. Flat conductor shall be of Hot Dipped & Cross sectional area of 90mm square
According to DIN EN 50164-2 (VDE 0185 part 202) Meets the requirement of
15 480 Mtr 27.00 12,960.00
VDE0185/305(IS-IEC 62305) Zinc coating: 500 g/m square (Approx:70 micron coating)
Should be tested and used exclusively for lightning protection earthing system and ring
equipotential bonding. OBO Type No. 5052 DIN 30X3 ( 5019 34 4 )

Providing of Cross connector for Flat: Suitable for 30mm Galvanised steel strip. Installed
16 37 Nos 70.00 2,590.00
with 4 nos of hexagonal plate. OBO Type No. 255 FL30 FT (5314 53 4 )
Providing of flat conductor holder suitable for FL 30. Installed with 2 hexagonal bolts.OBO
17 Type No. 166 LS 70 ( 5226 57 22 Nos 40.00 880.00
0)

Providing of Plastic Corrosion Protection strip: Approx 1.1 mm thick. Width 50mm. Made of
18 2 Nos 27.00 54.00
petrolatum- coated chemical fibre fabric. OBO Type No.356 50 ( 2360 05 5 )
19 Supply of UL Listed & CPRI tested maintenance free ,Low carbon copper coated earth rod of 11 Nos 315.00 3,465.00
20 3 metre electrode having diameter of 14.2 mm with copper coating thickness of 250micron 11 Nos 180.00 1,980.00
21 tested as per IEC 62561-2 ( OBO Type No. 14 3000 CCER)& is provided with universal clamp 11 Nos 135.00 1,485.00
22 made of SS to connect rod with flat conductor ( OBO Type No. 14 25 RTC) . Earth 11 Nos 18.00 198.00

TOTAL CARRIED TO SUMMARY 168,088

G. SUPPLY OF LIGHTING FIXTURES

This schedule of Quantities shall be read in conjuction with the technical specification,
1
General & Special conditions as well as all tender drawings.

The rates shall include all components that may be required to make the supply complete in
2
all respects such as :

a. Including All lamps, accessories & electronic ballast unless otherwise specified.

b. Internal wiring between accessories.

c. Earthing terminal.

d. Complete provision for installation.

G. SUPPLY OF LIGHTING FIXTURES

Supply of the following lighting fixtures with all fixing accessories etc. as required.

1X18W LED Single Luminaire Ceiling Mounted Surface tube Light Fixture (Philips or
1 1690 No.
Equivalent as confirmed by Client/Architect)

36 of 39
 Erection
SL ITEM DESCRIPTION QTY UNIT
RATE AMOUNT
1X18W LED Single Luminaire Ceiling Mounted Surface tube Light Fixture (Philips or
2 5 No.
Equivalent as confirmed by Client/Architect)

1X15W LED Single Luminaire Ceiling Mounted Surface Down Light Fixture (Philips or
3 1103 No.
Equivalent as confirmed by Client/Architect)

1X11W LED Single Luminaire Ceiling Mounted Surface Down Light Fixture (Philips or
4 520 No.
Equivalent as confirmed by Client/Architect)

1X13W LED Single Luminaire wall (Terrace)Mounted Light Fixture (Philips or Equivalent as
5 60 No.
confirmed by Client/Architect)

1X13W LED Single Luminaire wall Mounted Ramp Light Fixture (Philips or Equivalent as
6 180 No.
confirmed by Client/Architect)

1X28W LED Single Luminaire Ceiling Mounted Surface tube Light Fixture (Philips or
7 155 No.
Equivalent as confirmed by Client/Architect)

9W LED Luminarire Wall Mounted Mirror Light Fixture (Philips or Equivalent as confirmed
8 140 No.
by Client/Architect)

Bulk head lighting fixtures Philips make FXC 101 or approved equal in quality and design 9
9 360 No.
watt CFL lamps.

TOTAL CARRIED TO SUMMARY

H. INSTALLATION OF LIGHTING FIXTURES

This schedule of Quantities shall be read in conjuction with the technical specification,
1
General & Special conditions as well as all tender drawings.

The rates shall include all components that may be required to make the supply complete in
2
all respects such as :

a. Suitable length of GI down rod, hanger and connecting wires where called for..

b. Wires for connecting the fixtures to the point through connector block.

c. All metal blocks to serve as base of fixtures..

d. Bonding with earth wires..

3 Drilling holes in supports wherever required.

Fixing clamps, GI bolts and nuts, brass screws, saddles, rawl bolts and other fixing
4
accessories as required.

5 Testing of all fixtures & fans before and after installation.

H. INSTALLATION OF LIGHTING FIXTURES

Installation of the following lighting fixtures with all fixing accessories etc. as required.

1X18W LED Single Luminaire Ceiling Mounted Surface tube Light Fixture (Philips or
1 1690 No. 120.00 202,800.00
Equivalent as confirmed by Client/Architect)

2X18W LED Single Luminaire Ceiling Mounted Surface tube Light Fixture (Philips or
2 5 No. 120.00 600.00
Equivalent as confirmed by Client/Architect)

1X15W LED Single Luminaire Ceiling Mounted Surface Down Light Fixture (Philips or
3 1103 No. 100.00 110,300.00
Equivalent as confirmed by Client/Architect)

1X11W LED Single Luminaire Ceiling Mounted Surface Down Light Fixture (Philips or
4 520 No. 95.00 49,400.00
Equivalent as confirmed by Client/Architect)

37 of 39
 Erection
SL ITEM DESCRIPTION QTY UNIT
RATE AMOUNT
1X13W LED Single Luminaire wall (Terrace)Mounted Light Fixture (Philips or Equivalent as
5 60 No. 100.00 6,000.00
confirmed by Client/Architect)

1X13W LED Single Luminaire wall Mounted Ramp Light Fixture (Philips or Equivalent as
6 180 No. 100.00 18,000.00
confirmed by Client/Architect)

1X28W LED Single Luminaire Ceiling Mounted Surface tube Light Fixture (Philips or
7 155 No. 120.00 18,600.00
Equivalent as confirmed by Client/Architect)

9W LED Luminarire Wall Mounted Mirror Light Fixture (Philips or Equivalent as confirmed
8 140 No. 70.00 9,800.00
by Client/Architect)

Bulk head lighting fixtures Philips make FXC 101 or approved equal in quality and design 9
9 360 No. 120.00 43,200.00
watt CFL lamps.

TOTAL CARRIED TO SUMMARY 458,700

A CABLING AND INSTALLATION OF LIGHTING FIXTURE

FOR EXTERNAL / LANDSCAPE LIGHTING

INSTALLATION OF LIGHTING FIXTURES

Rate for installation of fixtures shall also include the following:

This schedule of Quantities shall be read in conjuction with the technical specification,
1
General & Special conditions as well as all tender drawings.

2 All component that may be required to make the installation complete in all respects.

a. Suitable length of connecting wires.

b. Connecting wires to the point through connection block.

c. Bonding to earth wires.

3 Drilling holes in supports wherever required.

Fixing clamps, GI bolts and nuts / brass screws, saddles, rawl bolts and other fixing
4
accessories as required.

5 Painting with enamel paint of clamps and other fixing accessories.

Suitable size junction boxes with connector block for loop in loop out where ever
6
applicable.

7 Testing of all fixture and after installation.

CABLING AND INSTALLATION OF LIGHTING FIXTURE FOR EXTERNAL / LANDSCAPE

A.
LIGHTING

Supply installing, testing and commissioning of the following lighting fixtures and poles
1
including excavation and back filling, foundation of pole, base plate as required.

lighting fixture with 60 watts LED Light including, capacitor a cast aluminium adapter Single
1.1 piece Street light with side reflectors with internal starter and with all necessary 21 No. 150.00 3,150.00
accessories.

Supply, laying, testing and commissioning of following size PVC insulated sheathed copper
conductor 1100 V grade armoured cable as per specification including excavation of earth,
2
300 mm thick and all around the cable, brick protection refilling, watering and ramming or
providing to earth etc. complete.

2.1 4C x 4 sq.mm 400 RM 124.00 49,600.00

38 of 39
 Erection
SL ITEM DESCRIPTION QTY UNIT
RATE AMOUNT
Making end termination of following size PVC insulated sheathed copper conductor 1100 V
3 grade armoured cable including cost of crimping lugs, sockets, double compression glands
with earthing facility etc. complete.

3.1 4C x 4 sq.mm 42 No. 40.00 1,680.00

Supplying and fixing of following bare GI tapes including all necessary fixing accessories
4
and effecting connections.

4.1 25 x 3 mm GI earthing strip 3500 RM 25.00 87,500.00

5 Supply & installation of 7.8 M high MS decorative poles (6 M above & 1.8 M below ground) 21 Nos. 3,150.00 66,150.00

Providing, installation, testing and commissining of 200 x 150 x 125 mm polycarbonate

weather proof (IP-55) junction box recessed in wall or surface mounted as required for
6 21 Nos. 135.00 2,835.00
housing of 1 no. 10 amps SP MCB’s suitable size of terminal blocks complete. Suitable
length of GI pipe upto junction box shall also be provided for laying of cables.

Wiring with 2 x 2.5 sq. mm. PVC insulated copper conductor 1100 V in 16 gauge 25 mm dia
GI conduit including connecting at terminals of lighting fixtures complete. The cost shall
7 140 RM 17.00 2,380.00
include supply and installation of conduit pipe, chasing of wall and making good. (
From Pole junction box to lamp)

Supply, installation, testing and commissioning of the following FDB's fabricated out of 1.6
mm thick CRCA sheet steel , double door construction, powder coated with approved
8 shade and partitions to segregate phases. Approved lockable covers with padlocking
arrangement for each phase, recessed in wall or surface mounted final distribution boards
of the following description:

8.1 External Lighting DB-1 (for Street Lighting with IP-55 )

Incomer : 1no. 16A FP MCB isolator with 16A 4P insulated copper busbars,plus 1 No. 16
amps TP Contactor controlled through 0-24 hour timer
Out going : 3 Nos. 16A DP RCCB, 30 mA,6 Nos. 10 amps SP MCB 1 Nos. 1,200.00 1,200.00

Providing and laying earth electrode system comprising of 80 mm dia concentric GI pipe,
with 2 Nos 50 x 6 mm GI. strips from electrode to inspection chamber, 50 mm dia medium
class GI pipe, CI funnel with 20 gauge GI wire mesh, masonry chamber C I heavy duty /
9 chequered plate manhole cover with frame painted with bitumastic paint and packing 4 Nos. 3,000.00 12,000.00
with special compound in rocky soil around electrode including digging or boring of pit
upto permanent moisture level and as per soil condition but not less than 3 meters and
back filling as required.for external lighting.

TOTAL CARRIED TO SUMMARY 226,495.00

I. INVERTER SYSTEM

Supply,installation, testing and commissioning of following Inverter having input 3 phase

(415 V + 10%) output 3 phase (415 V + 10%) with sealed maintenance free batteries
including suitable size of 14 gauge MS battery rack suitably painted. The rate shall be
1
inclusive of supporting rigid framework, all cabling between units, all fixing accessories
such as foundation bolts, nuts & bolts etc as required. Refer technical specifications for
details.

20 KVA Offline inverter input 3 phase (415 V + 10%) output 3 phase (415 V + 10%) with
1.1 1 Set 3,200.00 3,200.00
sealed maintenance free batteries suitable for 30 minutes backup

TOTAL CARRIED TO SUMMARY 3,200

39 of 39