About Us . . .

Since 1895, Smooth-On has been helping people like you

discover material possibilities. Smooth-On rubbers, plastics, foams and other
materials are used around the world to turn ideas into three dimensional reality.
This catalog offers a glimpse of what people
have created with these materials and will
hopefully inspire you to take the next step.

With hundreds of products to choose

from and the best technical support
available anywhere, we can help bring
your creation to life or get your project
up and running quickly.

Find Material Answers

for Your Project…
Smooth-On’s 380,000 ft2 (35,303 m2) facility in Macungie, PA
makes hundreds of materials that ship around the world.
Thousands of people visit smooth-on.com
everyday to view our videos and How-To
galleries. Step-by-step instructions will
help you understand how these materials
can work for your project.

You Are Never Alone…

Our world famous technical help is
available by e-mail or telephone. When
you call, you will talk to technicians that
have experience using these materials and
can guide you through your project.
The Smooth-On factory houses two of the largest silicone mixing
vessels in North America (1,500 gallons / 5,678 liters), each powered by
3 x 100 horsepower motors and high-shear mixing blades. ™
Hands-On Training…

Smooth-On offers two-day mold making and casting seminars that host people
from all over the world. Our training methods combine slides, videos, hands-on
demonstrations and discussions. Students use our materials to make their own
molds and castings and gain an unparalleled learning experience.

5600 Lower Macungie Road, Macungie, PA 18062 | Tel: 610.252.5800 | www.smooth-on.com

1
Table of Contents
03 Tin-Cure Silicone Rubbers

06 Platinum-Cure Silicone Rubbers

10 Specialty Silicones

12 Lifecasting Materials

15 Silicone Accessories

17 Polyurethane Rubbers

22 Polysulfide Rubbers

23 Polyurethane Plastics

31 Polyurethane Foams

33 Polyurethane Accessories

37 Laminating & Surface Coat Epoxies

39 Castable Epoxies

40 Epoxy Putties

43 Adhesives

45 Sprayable Silicone Rubbers & Foams

46 Sprayable Urethane Plastics & Rubbers

47 Polymer Modified Gypsum & Concrete Systems

49 Sealers & Release Agents

50 Mold Making & Casting Equipment

51 Skin FX & Starter Kits

53 Latex Rubbers

54 Clays

55 Material Specification Charts

66 Seminars

2
Tin-Cure Silicone Rubber
Mold Max Series ™
High Tear Strength, Low Cost, Versatile
Mold Max™ silicones are used around the world for a
variety of industrial and art-related applications
including architectural restoration, prototype
model development, reproducing sculpture,
creating special effects and themed environments.
Maximum Versatility – Mold Max™ silicones are
available in different Shore hardnesses and can be
poured or brushed onto almost any surface. They
capture the finest detail from any original model and
reproduce that detail perfectly in any casting. They can
be softened or thickened to customize the silicone for
your project.
Maximum Durability –
Mold Max™ silicones feature
high tear strength and are ideal for
production casting of wax (candle
making, wax foundry patterns)
gypsum plasters, concrete, urethane,
polyester and epoxy resins, low
temperature melt metal alloys and more.
Maximum Last-ability – featuring
Smooth-On’s exclusive “Libra” catalyst, molds Mold Max™ 14 NV has a high tear
made with Mold Max™ silicones will last for strength and does not require vacuum
years in your mold library. degassing. Liquid rubber pours
easily and flows well
over any surface.

Mold Max™ 25 used to create a Mold Max™ 40 used to make prototype

two-part mold for duplicating an pieces. This medium hardness silicone
industrial wheel. yields accurate castings
every time.

Mold Max™ 20 used

for a polyester lay-up
Mold Max™ 30 to make simple silicone molds to cast to make large scale
and paint foam replicas of props like shop tools. architectural elements.

3 Learn more at: www.smooth-on.com

 Tin-Cure Silicone Rubber

Mold Max™ 60 features high heat

resistance for casting metal
alloys such as tin, pewter,
etc. - up to 560°F / 294°C. Mold Max™ STROKE™
is convenient and cost
effective. It self thickens and
holds a vertical surface for
making detailed brush-on molds.

1. MIX

2. POUR
Mold Max™ 10 3. DEMOLD
∙ 10A Durometer
Mold Max™ 14NV & 29NV
∙ 14A & 29A Durometer
∙ No Vacuum Required
Mold Max™ 20
∙ 20A Durometer
Mold Max™ 25
∙ 25A Durometer Mold Max™ - eXtra Low Shrinkage II
Mold Max™ 30 Long term dimensional stability and
∙ 30A Durometer resistance to chemically harsh resins makes
Mold Max™ 40 XLS™ a favorite with prototype shops.
∙ 40A Durometer
Mold Max™ 60
∙ 60A Durometer
∙ Heat Resistant Up to 560˚F/294˚C
Mold Max™ STROKE
∙ 30A Durometer
∙ Brushable Mold Max™ 25 has a
Mold Max™ XLS™ II relatively low initial viscosity
∙ 30A Durometer for easier mixing, vacuuming
∙ ResinShrinkage
Low and pouring.
∙ Resistant

Learn more at: www.smooth-on.com 4

Tin-Cure Silicone Rubber
Mold Max™ T Series
Translucent For Easy Color Pigmenting
Mold Max™ 10T, 15T & 27T silicones are water white
translucent tin-cure silicone rubber compounds that have
exceptional tear strength, working properties and library life.
Mold Max™ T translucent rubbers are ideal for creating
animatronic skins and special effects using Silc Pig™ silicone pigments.
Mold Max™ 10T, 15T & 27T silicones can be thickened with
THI-VEX™ additive for brush-on applications.

Mold Max™ 10T 10A Durometer

Mold Max™ 15T 15A Durometer
Mold Max™ 27T 27A Durometer

Mold Max™ 27T silicone is used for

an animatronic dinosaur skin in a
themed restaurant in Florida.

OOMOO™ Silicones
It doesn’t get any easier!
Perfect for beginners, hobbyists and craft makers,
OOMOO™ silicones are easy to use and inexpensive.
They don’t require special equipment to process and
are ideal for making one-piece or two-piece block
molds.
OOMOO™ molds are good for fast prototyping and
model making, creating resin jewelry and home
hobby projects.

OOMOO™ 30 used OOMOO™ 25

to mold custom candles ∙ 25A Durometer
as seen on ∙ 1575 minute pot life
“The Martha Stewart Show.” ∙ minute demold time
OOMOO™ 30
∙ 30A Durometer
∙ 306 hour
minute pot life
∙ demold time

5 Learn more at: www.smooth-on.com

 Platinum-Cure Silicone
Mold Star Series ™
1A:1B Mix By Volume, Low Viscosity Silicones
Mold Star™ silicones are easy-to-use and feature relatively low
viscosity, meaning vacuum degassing is not required. Mold Star™ No Scale
No Vacuum
cures to a strong rubber that has good tear resistance and exhibits
very low, long-term shrinkage. Molds made with Mold Star™
silicones will last a long time in your mold library and are good
for casting wax, gypsum, resins, and other materials.
Required!
Mold Star™ Series
Mold Star™ 15 SLOW 15A Durometer
Mold Star™ 16 FAST 16A Durometer
Mold Star™ 30 30A Durometer

Mold Star™ Translucent Series Mold Star™ 30

is a durable, low viscosity silicone
Mold Star™ 14T 14A Durometer that reproduces exact detail from
Mold Star™ 19T 19A Durometer the original!
Mold Star™ 20T 20A Durometer
Mold Star™ 31T 30A Durometer

Mold Star™ 16 Fast

is also available in 400 ml cartridges.
See dispensing guns on page 50.
Mold Star™ 20T
is translucent and offers a great
fast-curing soft silicone option.

Rebound™ Series
Self-Thickening Brush-On Silicone Rubber
Rebound™ 25 and 40 are easy-to-use platinum-cure silicone
rubbers that self-thicken for making brush-on molds of almost any
model. Rebound™ can be applied with a brush or spatula to vertical
surfaces and cures with negligible shrinkage to a soft, flexible rubber.

Rebound™ 25 25A Durometer

Rebound™ 40 40A Durometer

SOFT, HIGH
Create strong, durable production molds for
casting wax, gypsum, concrete or resins. TEAR STRENGTH
Learn more at: www.smooth-on.com 6
Platinum-Cure Silicone
Smooth-Sil™ Series
Archival, Minimum Long-Term Shrinkage
Smooth-Sil™ silicones are ideal for making production molds of any configuration,
large or small. Urethane resins, urethane foams, epoxies, polyester resins, wax and
low-melt metal alloys can be cast into Smooth-Sil™
without application of release agent.
Smooth-Sil™ 933 FR 33A Durometer
Smooth-Sil™ 936 is the perfect choice for creating • Flame Rated
GFRC architectural elements. It is both chemical Smooth-Sil™ 936 36A Durometer
and abrasion resistant. With virtually no shrinkage, • Lower Viscosity
Smooth-Sil™ 936 molds produce identical castings Smooth-Sil™ 940* 40A Durometer Smooth-Sil™ 945 offers
time after time. the convenience of a 1A:1B
Smooth-Sil™ 945 45A Durometer
by volume mix ratio and a
Smooth-Sil™ 950* 50A Durometer fast 6 hour cure time.
Smooth-Sil™ 960* 60A Durometer
*Suitable for food grade applications

Smooth-Sil™ 950 is ideal for applications where precise

Smooth-Sil™ 940, 950 & 960 meet FDA compliance for food dimensional reproduction is required. Firm yet flexible,
grade applications, making them suitable for baking molds and Smooth-Sil™ 950 also reflects fingerprint detail for the most
trays, ice trays, for casting butter, candy or chocolate and other accurate casting possible.
applications used to produce food.

SORTA-Clear Series ™
Translucent Silicone Rubber
SORTA-Clear™ 12, 18, 37 and 40 are premium water white
translucent silicones that cure at room temperature. They feature exceptional tear and
tensile strength. Rubber clarity is especially useful when extracting models via cutting.
SORTA-Clear™ rubber is ideal for making prototypes, jewelry or other molds of any
configuration where model visibility is important. SORTA-Clear™ 18, 37 and 40 are
also food safe and used to make custom chocolates,
candy, cakes & more.

18
Sorta Clear™ le for
it a b
molds are su stings and 1 
production cad use!
repeate

3 

SORTA-Clear™ 12 12A Durometer

SORTA-Clear™ 18* 18A Durometer
SORTA-Clear™ 37* 37A Durometer
SORTA-Clear™ 40* 40A Durometer
2  4
*Suitable for food grade applications
7
 Platinum-Cure Silicone
Dragon Skin Series ™
Soft, Strong, Flexible, Stretchy... Incredible!
Dragon Skin™ is known around the world as the most versatile
silicone available anywhere. Available in 2A,10A, 15A, 20A, or 30A Shore
hardness, Dragon Skin™ silicones are easy to use and can be colored with
Silc Pig™ color pigments or painted with the Psycho Paint™ system.
Dragon Skin™ silicones are used to make lasting lifelike skin and monster
effects for animatronics. They are perfect for making stretchy “glove molds”
of models with deep undercuts for casting resin, plaster, etc.
Because of their extreme flexibility and wear resistance, Dragon Skin™
silicones are used extensively for coating fabric, shock absorption
and other industrial applications.

Dragon Skin™ 10 NV
requires no vacuum degassing!
Easily make glove molds that
Dragon Skin™ are soft and stretchy.
mermaid suit with
Cast Magic™ and
Silc Pig™ colorants.

Dragon Skin™ 10
is perfect for durable,
stretchy, long lasting masks.

Incredibly
Elastic
Dragon Skin™ 10 10A Durometer Dragon Skin™ 15 15A Durometer
• vailable in Slow, Medium,
A Fast, & Very Fast Dragon Skin™ 20 20A Durometer
Dragon Skin™ FX-Pro™ Dragon Skin™ 10 AF 10A Durometer Dragon Skin™ 30
is specifically designed for creating silicone
makeup appliances and skin effects.
• nti Fungal
A
Dragon Skin™ FX-Pro™
30A Durometer
2A Durometer
Dragon Skin™ 10NV 10A Durometer
• No Vacuum required
Learn more at: www.smooth-on.com 8
Platinum-Cure Silicone
Ecoflex Series ™
Soft, Softer, Softest...
Extreme Flexibility and Performance
Ecoflex™ Super-Soft rubbers are “sister”
silicones to our Dragon Skin™ series.
Available in Shore hardnesses down to a 000-34,
Ecoflex™ silicones are extraordinarily soft, strong,
durable and offer tremendous wear resistance.

Ecoflex™ 00-30 mask and gloves Like Dragon Skin™, these rubbers are easy to
painted with Psycho Paint™ by use and can be vibrantly colored with Silc Pig™ or Ecoflex™ 00-30 Ecoflex™ 00-31
Composite FX. painted with Psycho Paint™. Ecoflex™ Super-Soft Near Clear™
silicones are used for creating incredible skin effects, monster masks and special effects
appliances. They are also used extensively for medical cushioning applications, including
making orthotic and orthopedic appliances, and for coating fabric.

Ecoflex™ Gel 000-35 Durometer

Ecoflex™ Gel 2 000-34 Durometer
Ecoflex™ 00-10 00-10 Durometer
Ecoflex™ 00-20 00-20 Durometer
Ecoflex™ 00-20 Fast 00-20 Durometer
Ecoflex™ 00-30 00-30 Durometer
Ecoflex™ 00-31 Near Clear™
00-31 Durometer
Heel pads made of
Ecoflex™ 00-33 AF Anti Fungal Ecoflex™ silicone provide
00-33 Durometer excellent comfort and
Ecoflex™ 00-35 Fast 00-35 Durometer shock absorption.
Ecoflex™ 00-45 Near Clear™ Ecoflex™ 00-50 is used
00-45 Durometer to fabricate silicone socket
liners for prosthetic limbs.
Ecoflex™ 00-50 00-50 Durometer
Ecoflex™ 5* 5A Durometer
* Available in Cartridge Only

Soma Foama™
Soma Foama™ 15 and 25 are soft, flexible
silicone foams that can be poured into a
mold or over other surfaces when lighter
weight castings are required.
Soma Foama™ is used for a variety of
industrial and special effects applications
including making foam filled appliances,
padding/seat cushioning, and orthopedics.

Soama Foama™ 15 15 lb/ft³

Soma Foama™ produces
Soama Foama™ 25 25 lb/ft³ lightweight, flexible castings.

9 Learn more at: www.smooth-on.com

 Specialty Silicone
Encapso K ™
Water Clear Encapsulation / Display Rubber
Encapso™ K is a perfectly clear
encapsulation rubber that looks just
like water. Unlike chemically harsh
resins normally used for encapsulation,
Encapso™ K is safe and non-toxic.
Perfect for creating artificial floral
displays, water pond effects, etc.

l a t e A l m ost
Encapsu hing!
Anyt
Safe & Non-Toxic!
A convincing drink display piece used to advertise
at a tropical bar in Mexico - helps sell drinks and
the prop lasts for years!

Rubber Glass ™
Water Clear Silicone Rubber Compound
Rubber Glass™ is a solid, water clear rubber that can be easily broken
or “crumbled” into pieces that look exactly like broken glass, ice or Ice That
diamonds. Vibrant colors are possible by adding Silc Pig™ colorants D o e s n ’t
M e lt !
or Silc Pig™ Electric color pigments. Rubber Glass™ is used to
create a variety of special effects and model effects.

Rubber Glass™ ice effect was used instead of real ice to solve the
problem of replacing melting ice during an 8 hour photo shoot to
make a magazine ad.

Solaris ™
Clear Silicone Encapsulating Rubber
Solaris™ is a low viscosity, clear silicone
designed to protect electronic components
and other assemblies against shock, vibration,
moisture, ozone, dust, chemicals and other
environmental hazards. The optical clarity of
Solaris™ makes it suitable for potting solar
cells for maximum light transmission or
electronic assemblies where component
identification is necessary.
P ro te c t
Learn more at: www.smooth-on.com
E le c tr ic a l C o m p o n e n ts !
10
Specialty Silicone
EZ-Brush Vac Bag Silicone ™
Brushable Platinum Silicone Rubber
EZ-Brush™ Vac Bag Silicone was developed especially for making high
performance, reusable vacuum bags. Compared to vacuum bagging
films, EZ-Brush™ is much faster at delivering production-ready vacuum
bags, and offers tremendous time and labor savings.

Boat Production In Overdrive

Finished parts are delivered in a fraction
of the time using Vac Bag Silicone vs.
conventional bagging materials.
EZ-Brush™ Vac Bag silicone can also be
used for fast, large scale brush-on molds.

Equinox ™
Silicone Putty
Equinox™ silicone putty products can be mixed and applied by
hand to a variety of surfaces. Shrinkage is low and cured rubber
is exceptionally strong (very high tensile strength). Applications
include making fast mold impressions from almost any surface,
equine hoof repair, jewelry making and more. Equinox™ rubbers
are also food safe* and used to make custom chocolates, candy,
cakes and more.
Equinox™ 35 Fast 35A Durometer
Equinox™ 38 Medium 38A Durometer
Equinox™ 40 Slow 40A Durometer
Equinox™ silicone putty is perfect for making molds
*
Refer to Technical Bulletin for more details on-site when other methods can’t be used.

Mold Making On The Fly . . .

PoYo™ Putty 40
PoYo™ Putty 40 mold making putty is mixed
by hand and can be applied anywhere, anytime.
PoYo™ Putty 40 can be pressed onto almost any
surface and can be used to make fast molds for
casting resin, wax, etc.
No Mess, No Waste.
11 Learn more at: www.smooth-on.com
 Lifecasting Materials
Body Double Silicone ™
Apply
Easily
Releases
“Apply to Skin” Platinum Silicone Rubber From
Body Hair
Body Double™ Fast Set and Standard Set
have become Hollywood favorites for
capturing and reproducing faces, hands,
and other body parts.
Body Double™ SILK releases from
closely cropped hair-covered skin
without a release agent. Skin Safe
SILK is compatible with original
Body Double™ Standard and Fast
and captures perfect detail. Perfect
Unlike alginates, Body Double™ molds will Copy!
last for many castings of almost any material
including plaster, Matrix™ NEO, wax, resins
(Smooth-Cast™ urethanes, polyester, etc.),
low-temperature melt metal alloys, etc.
Body Double™ SILK easily releases from
Body Double™ silicone can closely cropped hair-covered skin.
capture details down to a fingerprint.

Patent Pending

Alja-Safe™ ™& Alja-Safe™ Breeze

Acrobat Liquid Alginate
Crystalline-Silica Free
Powder Alginates
Crystalline-Silica Free No Powder - No Dust!

Alja-Safe™ is easy to use, cures quickly, and is Alja-Safe™ Breeze is a liquid

much less expensive than silicone. Acrobat™ alginate which blends easily
is a “non-sag” fiber reinforced alginate, perfect with water, creating a unique,
for making molds of the face and torso. Both skin-safe moldmaking material.
reproduce fine detail and make an excellent Alja-Safe™ Breeze is perfect
“single use” mold. You can cast plaster, for making single-use pourable
Matrix Dryve™, platinum-cure silicone, molds of hands, feet and other
or Smooth-Cast™ 300Q urethane resin body parts. It captures excellent
into the mold to make detail, giving you an accurate
a reproduction. reproduction of your original.

Alja-Safe™ is used to create a prop arm Alja-Safe™ Breeze

that looks just like the real thing. offers significantly less bubble
entrapment vs. powder alginates
and is virtually bubble free.

Acrobat™ is thicker and holds a vertical surface - great for molds of the face.
Learn more at: www.smooth-on.com 12
Lifecasting Materials

FaceGel™ 590
Thicker - Holds Vertical Surface
Accu-Cast™ FaceGel™ 590 alginate is an easy to use alginate mold material that is ideal
for making layup molds used to reproduce fine details of a face. FaceGel™ 590 has
extra thickener which allows it to hold a vertical surface
well with minimal slump, and makes an excellent
temporary lifecasting mold. FaceGel™ 590 has a
set time of 5 minutes when mixed with water
that has a temperature of 90°F / 32°C.

BabyGel™ 2
Fast - Changes Color when Curing
BabyGel™ 2 alginate is a fast
HandGel 570 Fine Details
™ curing, skin safe alginate mold
material that is ideal for making
accurate reproductions of your
HandGel™ 570 alginate is an easy to use baby’s / child’s hand or foot.
alginate mold material that is ideal for making BabyGel™ 2 is unique because
poured molds used to reproduce fine detail of when it is mixed with water at
the hands, feet and other body 80°F / 27°C, it visually changes
parts using a large container or color from pink to gray as it
bucket. HandGel™ 570 makes an cures. This visual indicator makes it
excellent temporary lifecasting easy to determine when to insert
mold and has a set time the baby’s / child’s hand or foot
of about 5 minutes into the mold gel. Mold will cure in
when mixed with water about 3 minutes.
that has a temperature
of 70°F / 21°C.

BodyGel™ 880
Large Surface Coverage
BodyGel™ 880 alginate is an easy to use alginate mold
material that is an ideal choice for making molds which
require coverage over a broad surface area of the body
such as torsos or full body molds. BodyGel™ 880 makes an
excellent temporary lifecasting mold and has a set time of approximately
8 minutes when mixed with water that has a temperature of 80°F / 27°C.

13 Learn more at: www.accu-cast.us

13
 Lifecasting Materials
BabyGel™ 2
• 2 minute pot life
• 3 minute demold time
• water temp - 80°F / 27°C
370-SD™ Prosthetics & Orthotics BodyGel™ 880
• 5 minute pot life
Accu-Cast™ 370-SD™ alginate is a fast curing, firm alginate
• 8 minute demold time
mold material that is ideal for socket duplication in the creation
of prosthetics and orthotics. This firm alginate can be poured • water temp - 80°F / 27°C
into a prosthetic socket to assist in the fitment of artificial FaceGel™ 590
limbs. 370-SD™ has a set time of about 3 minutes when mixed • 3.5 minute pot life
with water that has a temperature of 70°F / 21°C. • 5 minute demold time
• water temp - 90°F / 32°C
HandGel™ 570
• 3.5 minute pot life
• 5 minute demold time
LIFECASTING KITS • water temp - 70°F / 21°C
Our kits are the fastest way we know to 370-SD™
get you started. We have a full range of kits • 32 minute
minute pot life
including Baby/Child Hand, Adult Hand, • demold time
Family Hand, Face, Head and Full Torso • water temp - 70°F / 21°C
Casting. Replacement Alginates, LiquiStone™
Fun Silicone™
and Plaster Bandages are available. Kits
contain everything you’ll need - except • 6 minute pot life
water. Everything is pre-measured, • 30 minute demold time
and our exclusive “Mix-In-The-Bag” LiquiStone™
technique makes cleanup a snap. • 153 hours
minute pot life
• demold time

FUN Silicone
Accu-Cast™ FUN Silicone™ is a soft
™
silicone rubber made especially for casting
into alginate molds to make flexible, exact
rubber reproductions of body parts.
FUN Silicone™ is easy to use and cures to a
strong rubber that is tear resistant and exhibits
very low long term shrinkage. Fully cured silicone LiquiStone™
rubber is certified skin safe. Parts made with
FUN Silicone™ will last a long time and are easy Easy To Use Casting Gypsum
to clean (dishwasher safe). An infinite number Accu-Cast™ LiquiStone™ is an easy to use gypsum
of color effects can be achieved by adding cement that can be cast into Accu-Cast™ alginate molds for
Silc Pig™ silicone pigments reproducing human body parts for lifecasting. LiquiStone™
or Cast Magic™ has a convenient mix ratio of 2 parts powder to 1 part
powders. water by volume and will have a working time of about
15 minutes. Castings can be demolded in about 3 hours.
LiquiStone™ can be cast solid, or can be laid up by hand
(thicker consistency required). Fully cured castings can be
machined, sanded, primed and painted.
You can cast LiquiStone™ gypsum cement, plaster,
duoMatrix™ NEO (polymer modified gypsum) or
Smooth-Cast™ 300Q ultra-fast urethane resin into
alginate molds to make reproductions.

Learn more at: www.accu-cast.us 14

Silicone Accessories
For Use With Tin-Cure
Silicones Only
Fast Cat™ 30
Used in place of (or in combination with) Mold Max™ 30 regular
Part B catalyst, Fast Cat™ 30 will reduce the demold time from
overnight to as little as 30 minutes.

Fast Cat™ 30 can accelerate Accel-T ™

is a one-component additive that will reduce the cure time of Smooth-On
Mold Max™ 30 so that it
will cure over frozen models! tin-cure silicone rubber compounds from overnight to a few hours in
proportion to the amount added.

For Use With Platinum-Cure Silicones Only

Psycho Paint ™
is a translucent clear silicone paint base developed to help special effects and prosthetic
artisans, doll makers, etc. easily create painted-on color effects for their silicone creations
with Silc Pig™ color pigments.
Psycho Paint™ iused to easily create
SLIDE STD™
Liquid Surface Tension Diffuser
painted-on color effects for their creative
platinum silicone designs.
greatly reduces surface tension when
added to platinum cure silicone.

Skin Tite ™
is a skin safe silicone used to create
fast wounds, scars and skin effects
appliances directly on the skin. It can also
be used to adhere silicone appliances or Derma-tac™ &
silicone masks to the skin.
Derma-tac™ Remover
Derma-tac™ is a pressure sensitive adhesive
designed for temporarily adhering silicone and
latex makeup prosthetic appliances to the skin.
Derma‑tac™ Remover is an easy-to-use one
component liquid that will dissolve Derma‑tac™
and aid in removing appliances from the skin.

Plat-Cat ™
Cure Accelerator
reduces the cure time of Smooth-On platinum silicones without
significantly affecting the ultimate physical properties.

Slacker ™
Tactile Mutator
is a liquid additive
used to ‘deaden’ the SLO-JO ™
Cure Retarder
extends the pot life (working time) of Smooth-On
silicone, making it
more flesh-like. platinum silicones and Soma Foama™ silicone foam
without affecting the ultimate physical properties.

15 Learn more at: www.smooth-on.com

 Silicone Accessories
For Use With
ALL Silicones
™
Silicone Pigments
are used for coloring all Smooth-On silicones. Create mind blowing skin
effects when used with Psycho Paint™ or Skin Tite™. Silc Pig™ pigments are
concentrated colorants that offer excellent dispersion and consistent color.

Red Yellow Blue Green Cyan Purple

PMS 186C PMS 107C PMS 2757C PMS 3292C PMS 631C PMS 2627C
Silc-Pig™ pigments are mixed with
Psycho Paint™ and applied with an
airbrush to paint the finishing touches
Blood Dark Flesh Med. Flesh Light Flesh Brown Black White on an Ecoflex™ silicone mask.
PMS 7421C PMS 469C PMS 479C PMS 488C PMS 4625C PMS BLACK PMS WHITE

™
Electric
Fluorescent Silicone Pigments
Electric
Pink
Electric
Green
Electric
Blue
Pantone values are approximate. PMS 812C PMS 802C PMS 300C
Allow more ultraviolet light from the cured silicone to
become visible to your eye vs. castings made with standard
Silc-Pig™ pigments. Castings appear brighter in ambient
light and appear to glow under UV light (black light). Electric Electric Electric
Orange Yellow Purple
PMS 1655C PMS 809C PMS 2405C

Si-Tac™ Adhesive FOR TEXTILES THI-VEX™ Silicone Thickener

is a liquid additive that thickens most Smooth-On mold
Si-Tac™ is a two-part pourable liquid silicone
adhesive that is applied to natural or synthetic making silicones making it easier to fill in undercuts or to
fabric/clothing for the purpose of keeping apply to vertical and inverted surfaces. Different viscosities
sports or leisure wear in place during exercise. can be attained by varying the amount of THI-VEX™ added.
Garments will not shift or fall. Si-Tac™ adhesive is very strong,
sweat resistant and lasts through many laundering cycles. Inhibit X™
is a single component, low-viscosity liquid that provides
• Customizable to Your • Resists Laundry Cycling an added measure of protection against cure inhibition
Specifications • Solvent Free, Non-Irritating when pouring platinum silicone rubbers over many
• Economical • Sweat Resistant surfaces including sulfur clay, instant adhesives, tapes,
• Control Rate of Cure with Heat • Highly UV-Resistant wood surfaces, some plastics, SLA resins and others.
• Colorless & Non-Staining • High Temp Resistance &
• Highly Stretchable Low Temp Flexibility Silicone Thinner™
is a non-reactive silicone fluid that will lower the mixed
viscosity of Smooth-On silicones.
STAYS IN
PLACE!
NOVOCS™ GLOSS & MATTE SILICONE SOLVENTS
are low viscosity solvents that evaporate quickly. They
will lower viscosity of Smooth-On silicone rubbers and
contain no VOC’s. They are particularly useful in thinning
down Psycho Paint™ silicone paint base to apply via
brush or airbrush to cured platinum silicone rubber.

Two Si-Tac™ silicone beads are delivered to APHIX™ Silicone Adhesion Promoter
a garment surface in a wave pattern. The garment will temporarily adhere most surgical tapes, bandages,
is then passed through a heat tunnel to cure the dressings, etc. to silicone rubber surfaces including
silicone in under 60 seconds. training mannequins, devices, etc.
Learn more at: www.smooth-on.com 16
Polyurethane Rubber
VytaFlex™ 60 rubber is dispensed from the
EZ-Mix™ Machine over a prepared model.
VytaFlex™ Series
Made Especially for Casting Concrete
VytaFlex™ mold rubbers have been used in the production of
concrete castings for over 20 years. This mold rubber is specially
formulated using Smooth-On’s exclusive “V-Polymer” technology for
casting pigmented/colored concrete. Molds made
with VytaFlex™ rubber offer superior abrasion resistance
and durability. They yield castings that are dimensionally
precise and color accurate every time. VytaFlex™ is
available in 10A, 20A, 30A, 40A, 50A and
60A Shore hardnesses.

VytaFlex™ liners are

positioned on the
casting deck. Form
walls are built around
the perimeter and for VytaFlex™ rubbers
window knockouts. are widely used to
create molds for
casting stone veneer

Rebar is positioned over

the form and concrete
is cast. A layer of
insulation is sandwiched
between two layers of
reinforced concrete.
VytaFlex™ 10 10A Durometer
∙ 3024 minute pot life
∙ hour demold time
VytaFlex™ 20 20A Durometer
∙ 3016 minute pot life
∙ hour demold time
VytaFlex™ 30 30A Durometer
∙ 3016 minute pot life
∙ hour demold time
VytaFlex™ 40 40A Durometer
∙ 3016 minute pot life
∙ hour demold time
The panels are sandblasted and stored in VytaFlex™ 45 45A Durometer
Slaw Precast’s yard prior to installation. ∙ 3016 minute pot life
∙ hour demold time
VytaFlex™ 50 50A Durometer
More than 230
∙ 6016 minute pot life
insulated concrete
panels were made ∙ hour demold time
by Slaw Precast, VytaFlex™ 60 60A Durometer
cast into custom ∙ 6016 minute pot life
VytaFlex™ 60 ∙ hour demold time
formliners.

17 Learn more at: www.smooth-on.com

 Polyurethane Rubber
ReoFlex Series ™
For Casting Plaster, Wax, Resins & More
ReoFlex™ Series urethane rubbers offer superior physical and performance
properties for production casting of wax, plasters, and resins. ReoFlex™
urethanes are available in 10A, 20A, 30A, 40A, 50A and 60A Shore hardnesses.

ReoFlex™ mold rubber picks up all

the intricate detail from this wall
plaque and ceiling medallion.

ReoFlex™ 20 20A Durometer

∙30 minute pot life
∙16 hour demold time
ReoFlex™ 30 30A Durometer
∙ 3016 minute
Easy
pot life
∙ hour demold time
ReoFlex™ 40 40A Durometer
∙ 3016 minute
to
pot life
∙ hour demold time

Use!
ReoFlex™ 50 50A Durometer ReoFlex™ rubbers are
∙ 5016 minute pot life widely used to cast wax
∙ hour demold time for candlemaking.
ReoFlex™ 60 60A Durometer
∙ 5016 minute pot life
∙ hour demold time

Formlastic 48 and 60 ™
Formlastic™ 48 and 60 filled urethane rubbers are used to make molds
for production casting of concrete. They feature low viscosity for easy
mixing / pouring and cure with minimal bubble
entrapment. Mix ratio is 1A:1B by volume, and the
rubbers cure in 24 hours to an ultimate Shore
hardness of either Shore 48A or 60A.

Cured rubber is dimensionally stable (low shrinkage), offers good

wear resistance and will render color accurate concrete castings.

Learn more at: www.smooth-on.com 18

Polyurethane Rubber
PMC Series ™
PMC -121/30 (Wet or Dry)
™

& PMC™-121/50
PMC™-121/30 Wet or Dry are longtime
favorites of artists, candlemakers and those
casting plasters. The wet version contains a
PMC™-121/50 built-in release agent to aid in demolding hard
Large architectural mold. plasters and concrete. The dry version does not
exude an oil and can be used for casting waxes,
liquid plastics, gypsum plasters, etc.
PMC™-121/50 is a “wet-only” version with
similar properties to PMC™-121/30 but has
a higher Shore Hardness (50A durometer).

Aura Ceramics of Easton, PA used PMC™-121/50 to

create detailed plaster reproductions of tiki dolls.

PMC™-744
PMC™-744 has been used for years by mold making
professionals to cast wax, plaster, concrete, resins,
etc. It is excellent for making molds that are strong,
durable and dimensionally stable.

Beeskep II uses PMC™- 744 for their

candlemaking business. The case
molds above are strong, durable and
dimensionally stable, yielding
predictable results with each use.
PMC™-744 ceramic bunny case mold.

PMC™ -121/30 Dry 30A Durometer PMC™-746

∙ 3016 minute pot life PMC™-746 was developed to
∙ hour demold time make molds for casting gypsum
PMC™ -121/30 Wet 30A Durometer plasters. Because of its durability
∙ 3016 minute pot life and moisture resistant properties
∙ hour demold time it is also used by zoos and
PMC™ -121/50 Wet 50A Durometer museums for a variety of mold
∙ 3016 minute pot life making, display and exhibit
∙ hour demold time applications. Other applications
include making plaster block
PMC™ -744 44A Durometer
∙ 1516 minute pot life molds, reproducing ornamental
∙ hour demold time plaster for architectural
restoration and resin casting.
PMC™ -746 60A Durometer
∙ 1516 minute pot life PMC™-746 molds are used for casting heavily filled polyester furniture elements
∙ hour demold time at Union City Mirror in New Jersey.

19 Learn more at: www.smooth-on.com

 Polyurethane Rubber
PMC Series ™
PMC™ 790 is used for this tough and

PMC -770, 780 & 790

™ abrasion resistant stamping pad that makes
beautiful european fan designs in concrete.
The PMC™ line of hard urethane rubbers is used for an endless
variety of industrial casting applications. Available in Shore 70A,
80A and 90A durometers, they are dimensionally stable and
feature exceptional physical properties, including high impact
resistance and tensile strength.
These rubbers offer extra long working times for pouring large
or complicated forms. Superior abrasion resistance makes these
urethanes the perfect choice for making molds for casting concrete
and making ball mill liners.
They are also used to make industrial rollers and belts, rubber mechanical
parts (such as gaskets, wheels, and pullies) and vibration/shock pads. They
are also used to stamp concrete indoors or out to beautify courtyards,
pool decks, driveways, stairways, patios and more.

Compat™ 45 PMC™-780 is used to create wear resistant bushings.

Non-Inhibiting Urethane Rubber

Compat™ 45 is a unique urethane rubber which will not inhibit the
cure of most Smooth-On platinum or tin cure silicone rubbers. It has
a mix ratio of 1A:1B by volume (85A:100B by weight), a low viscosity for
easy mixing and pouring and cures with minimal bubble entrapment.
Cured rubber is dimensionally stable (low shrinkage), offers good wear
resistance and an excellent library life.
Compat™ 45 can be used for a variety of applications including making
molds to cast silicone prop body parts, animatronic skins and medical
trainers; as well as for making rubber masters which can be molded using
platinum or tin silicone without
inhibition concerns. PMC™-770 70A Durometer
∙ 3016minute pot life
∙ hour demold time
Important: Do not use Ecoflex™ Gel, Ecoflex™ 00-10, Ecoflex™ Near Clear, Encapso-K, PMC™-780 DRY 80A Durometer
Rubber Glass™, Solaris™ or Sorta-Clear™ 12 or 37 with this product. They are not ∙ 2548 minute pot life
compatible and inhibition will result. ∙ hour demold time
PMC™-780 WET 80A Durometer
∙ 2548 minute pot life

Econ 60 & 80 ™
Econ™ 60 & 80 are lower cost rubbers compared to our
∙ hour demold time
PMC™-790
∙ 48 hour demold time
∙
20 minute pot life
90A Durometer

popular PMC™ Series. They are mixed 1A:1B by volume,

possess a relatively low viscosity, no odor, and cure Compat™ 45 45A Durometer
∙ 2516 minute pot life
quickly. They do have lower physical properties
compared to the ∙ hour demold time
PMC™ Series Econ™ 60 60A Durometer
rubbers, but ∙ 64 minute pot life
are suitable ∙ hour demold time
for many industrial Econ™ 80 80A Durometer
applications, including making ∙ 6 hour demold time
13 minute pot life
highly impact resistant prototype parts, fast ∙
concrete stamping pads and fast pour-in-place
gaskets for equipment. Econ™ 60 & 80 are both good
choices for making economical
concrete stamping pads.
Learn more at: www.smooth-on.com 20
Polyurethane Rubber
Brush-On Series ™
Ideal for Vertical or Inverted Surfaces
Smooth-On’s Brush-On™ urethane mold rubbers are known for having high
tear strength and exceptional abrasion resistance, making them a favorite of
concrete casters around the world.
Available in 35A, 40A, 50A or 60A durometer, these are “paste-liquid” systems
that are easy to use and hold vertical or inverted surfaces without sagging.
Rubber cures with minimal shrinkage and molds last a long time for
production casting of concrete, gypsum, wax and other materials.

VERSATILE – DID YOU KNOW?

MJM Studios applied Brush-On™ 40 on-site to create Brush-On™ rubbers are also
the architectural mold used to restore the arch atop used for a variety of industrial
New York City’s landmark Bellevue Hospital. applications including making wear
and water resistant coatings for fabric
and other surfaces, and as flexible
adhesives for bonding like and
unlike surfaces.

Brush-On™ 50 was center stage during

Chicago’s Garfield Park Field House
restoration. 17’ x 11’ GFRC dome panels
were cast from the molds below. Adding SO-Strong™ colorant
to every other layer aids in
differentiating between coats
so you are sure to achieve an
even coverage.

Brush-On™ 35 35A Durometer

∙ 2016 minute pot life
∙ hour demold time
Brush-On™ 40 40A Durometer
∙ 2016 minute pot life
∙ hour demold time
Brush-On™ 50 50A Durometer
∙ 2016 minute pot life
∙ hour demold time
Brush-On™ 60 60A Durometer
∙ 2016 minute pot life
∙ hour demold time
EZ-Mix™ 40 40A Durometer
∙ 1816 minute pot life
∙ hour demold time Brush-On™ 60 was used
to create the highly
detailed mold for this

EZ-Mix™ 40
boy scout statuette from
Maslyn Studios.

EZ-Mix™ 40 is a very easy to mix

“liquid-liquid” urethane rubber that
is great for beginners. EZ-Mix™
rubber is a favorite with sculptors and
is good for casting wax or gypsum.

21 Learn more at: www.smooth-on.com

 Polyurethane & Polysulfide
Clear Flex Series ™
Rubber
Water Clear, Flexible and UV Resistant
Clear Flex™ are tough rubbers that are water white clear and used for
applications including encapsulation, making prototype parts, props and
special effects. Choose between a flexible 30A and 50A, or a semi-rigid 95A.
All are UV resistant and are easily color pigmented for a variety of effects.

Clear Flex™ 30 is a product that

is flexible, and does not contain
mercury or phthalates.

Casino themed Clear Flex™ 30 30A Durometer

objects were ∙ 1516 minute pot life
encapsulated inside this ∙ MERCURY FREE time
hour demold
Clear Flex™ 95 elevator
hand railing bumper.
∙
Clear Flex™ 50 50A Durometer
∙ 2516 minute pot life
∙ hour demold time
Clear Flex™ 95 95A Durometer
Clear Flex™ 50 is used to ∙ 2516 minute pot life
encapsulate reflective materials in a free-spinning ∙ hour demold time
head on TopGun fishing lures. Fish cannot resist!

FMC™ 200
∙
∙
50 minute pot life
20A Durometer
FMC Polysulfide
™
16 hour demold time
FMC™ 201 15A Durometer
Time Tested FMC™ Polysulfide
∙ 16 hour demold time
50 minute pot life Used by artists and industry for over 70 years,
∙ FMC™ Polysulfide rubbers are soft and very
FMC™ 205 12A Durometer strong, perfect for making molds of originals
∙ 9016 minute pot life with deep undercuts. They can be applied
∙ hour demold time to wet models or sulfur based clays without
inhibition. Molds last for years
in your mold library.

Gypsum segments are

cast into polysulfide
molds, then assembled to
make steel molds used to
make production tires.

FMC™ rubber was used to mold an 8 ft. (2.4 m) clay model of a horse based on
Leonardo DaVinci’s drawings and chronicled in National Geographic Magazine.
Learn more at: www.smooth-on.com 22
Polyurethane Plastic
Smooth-Cast Series ™
General Purpose Casting Resins
Smooth-Cast™ 300 Series - Bright White
Smooth Cast™ 300 Series liquid plastics are
ultra-low viscosity casting resins that yield
castings that are bright white and virtually
bubble free. Vacuum degassing is not necessary.
They offer the convenience of a 1A:1B by volume mix
ratio. Fully cured castings are tough, durable, machinable
and paintable. They resist moisture and mild solvents.
Applications for Smooth-Cast™ 300 Series plastics
include reproducing small to medium size sculptures, Production
making prototype models, and special effects props. Ready

Fast-Setting, Durable,and
Perfectly Detailed

Smooth-Cast™ 300Q
∙ 304 - second pot life
∙ 5 minute demold time
Smooth-Cast™ 300 Easy to Paint & Finish
∙ 310minute pot life
∙ minute demold time
Smooth-Cast™ 305
∙ 730minute pot life
∙ minute demold time Smooth-Cast™ 320 Series
Smooth-Cast™ 310
∙ 153 --420hour
minute pot life
Off-White
∙ demold time The Smooth-Cast™ 320 Series liquid plastics are
Smooth-Cast™ 320 “sister” products to our popular Smooth-Cast™
∙ 310minute pot life 300 Series but cure off-white. They are
∙ minute demold time easier to color using SO-Strong™, UVO™ or
Ignite™ colorants.
Smooth-Cast™ 321
∙ 730- minute
9 minute pot life Smooth-Cast™ 320 Series resins also readily
∙ demold time accept fillers (such as URE-FIL™ 3, 5, 7, 15, 17
Perfectly
Detailed
Smooth-Cast™ 322 and 19). Fully cured castings are tough, durable,
∙ 102 - -420hourminute pot life machinable and paintable. They resist moisture
∙ demold time and mild solvents. Applications for Smooth-Cast™
320 Series resins include reproducing small to
medium size sculptures,
making prototype
models, special effects
props, decorative
jewelry and
taxidermy (bones,
antlers, teeth, etc.).

Smooth-Cast™ 320 Woodgrain Effect Created Using

Bear Skull Smooth Cast 320™ with
URE-FIL™ 5 and SO-Strong™ Brown

23 Learn more at: www.smooth-on.com

 Polyurethane Plastic
Smooth-Cast Series ™
Cast Magic™
General Purpose Casting Resins Powders

Smooth-Cast™ 325 Series - ColorMatch™

Smooth-Cast™ ColorMatch™ plastics are urethane resins that were
developed specifically for adding color pigments and fillers to achieve
a true color representation or filler effect. The ColorMatch™ Series is
formulated to be “color neutral.” Small amounts of SO-Strong™, UVO™
or Ignite™ colorants will yield accurate, vivid colors from cured castings.
Because of its neutral color, the ColorMatch™ Series is ideal for creating Cold
marble and woodgrain casting effects, or duplicating the look of real Cold Cast
t
metal by adding bronze, brass or other metal powders. Ca st Marble Effec Metal
Effect

EASIEST TO COLOR Smooth-Cast™ 325

∙ 2.5 minute pot life
∙ 10 minute demold time
Smooth-Cast™ 326
∙ 760- minute
9 minute pot life
∙ demold time

Smooth-Cast™ 327
∙ 102 - -420hourminute pot life
∙ demold time

Smooth-Cast™ ONYX™ - Deep Black

Smooth-Cast™ ONYX™ is a mercury-free urethane resins that lve
r per m nze ss
cure quickly at room temperature to a deep black, solid plastic. l/Si Cop minu Bro Bra
Nicke Alu
ONYX™ has an ultimate shore hardness of 80D and offers higher
physical properties and higher heat resistance vs. other general
purpose resins. Applications
Smooth-Cast™ ONYX™ FAST include reproducing
∙2.5 minute pot life sculpture, making prototypes
∙10 - 15 minute demold time and potting/encapsulation.
Because ONYX™ is a fast
Smooth-Cast™ ONYX™ SLOW curing resin and becomes
∙5 minute pot life hard quickly, it is also great for
∙90 minute demold time doing fast cold cast bronze,
Smooth-Cast™ ONYX™ is combined with different metal
brass, copper, nickel/silver and powders to achieve a realistic metal finish.
other metals.

Fast Cure
Low Viscosity

Deep
Black
Color

Learn more at: www.smooth-on.com 24

Polyurethane Plastic
Smooth-Cast™
Smooth-Cast Series ™
semi-rigid resins
are available General Purpose Casting Resins
in different
hardnesses.
Smooth-Cast™ Semi-Rigid Resins
Smooth-Cast™ 45D, 57D, 60D, 61D, 65D and
66D are low-cost urethane casting resins that
cure quickly to semi-rigid plastics that offer
excellent impact resistance. These plastics are
easy to use (mix ratio is 1A:1B by volume) and
have low viscosities for minimal bubble
entrapment. Vibrant colors are possible by
adding SO-Strong™, UVO™ or Ignite™ colorants.
These semi-rigid plastics will really take a beating and offer exceptional abrasion Smooth-Cast™ 57D
resistance. They are good for making high-impact resistance tools, prototypes, etc. can really take
a beating!

Smooth-Cast™ Semi-Rigid Resin ‘Shore D’ Hardness Comparison:

45D 57D, 60D & 61D 65D & 66D 70D (for comparison)
Softer, Bendable Some Flexibility Semi-Rigid Rigid, Not Flexible

Smooth-Cast™ 45D
∙ 530minute pot life
∙ minute demold time
Smooth-Cast™ 57D
∙ 3 minute pot life
Smooth-Cast™ 65D
∙ 30 minute demold time Smooth-Cast™ 65D is unique among the semi-rigid resins.
Smooth-Cast™ 60D It has a gradual cure profile making it ideal for rotational
∙ 530minute pot life casting applications. It can be cast hollow or filled with foam for
∙ minute demold time lightweight reinforcement.
Smooth-Cast™ 61D
∙ 760minute pot life
∙ minute demold time
Smooth-Cast™ 65D
Smooth-Cast™ 65D
∙ 2.5 minute pot life
boulders weigh less than
∙ 10-15 minute demold time 8 lbs / 3.6 kg!

Smooth-Cast™ 66D
∙ 760minute pot life
∙ minute demold time
Dozens of Smooth-Cast™ 65D
boulders were cast to launch
the JEEP® model at the
New York Auto Show.

25 Learn more at: www.smooth-on.com

 Polyurethane Plastic
Smooth-Cast Series ™
Smooth-Cast™ 380 tool used
to cast a electronics
General Purpose Casting Resins utility housing.

Smooth-Cast™ Tooling Resins

Smooth-Cast™ 380 and 385 are mineral filled urethane casting resins that are very hard and
durable. They also cure with low shrinkage. Smooth-Cast™ 380 features ultra high density
and very low cost. Smooth-Cast™ 385 has high compressive and flexural strength.
Fully cured castings are tough, machinable and paintable. Tooling resins are ideal
for making industrial parts, foundry patterns, vacuum forming molds, and some
ceramic applications.

Smooth-Cast™ 385 master molds can be used to cast

silicone rubber production molds.
Rigid Smooth-Cast™ 385
Propeller Model

Feather Lite™ - It Floats In Water!

Feather Lite™ is a heavily filled, low-density
urethane casting resin. Cured plastic is lightweight
(it floats in water!) and can be carved, machined,
sanded, etc. Feather Lite™ can be pigmented with
SO-Strong™ and UVO™ colorants and finished castings can
be painted. Feather Lite™ yields more plastic per pound/kg. than
other resins, lowering the cost per casting.

Feather Lite™
ventriloquist
puppets
are easy to
handle.

6 ft (1.8 m) long Feather Lite™

flying fish on display at the
Atlantic City Convention Center.
Feather Lite™
fishing lures that float!

Learn more at: www.smooth-on.com 26

Polyurethane Plastic
TASK Series™
High Performance Casting Resins
TASK™ Series plastics are a line of urethane casting resins that offer superior
physical properties compared to our popular Smooth-Cast™ line of general
purpose casting resins. TASK™ plastics feature mix ratios by volume (pbv)
or weight (pbw), low viscosities, high tensile and flexural strength, as well as
high flexural modulus.

TASK™ 2 & TASK™ 3 - Low viscosity, fast cure resins made especially
for rapid prototyping environments.
TASK™ 4 - With exceptional flexural strength, TASK™ 4 plastic
was developed to be unbreakable when cast in ultra thin-wall
sections - as thin as a sheet of paper.
TASK™ 5 & TASK™ 6 - Time tested economy performance resins.
TASK™ 7 Flame Out™ - Low viscosity, fast set resin that
meets UL 94 V-O requirements for flame resistance.
TASK™ 8 - Heat resistant urethane plastic that can withstand
temperatures up to 263°F/129°C.
TASK™ 9 ColorMatch™ - Readily accepts color pigments
and yields parts with extraordinary tensile strength.

TASK™ 2 was used to create

prototype oversized remote
controls used for consumer
testing prior to final production.

TASK™ 4 has
been a regular fixture of
prototype shops around the world
for over 50 years, helping bring TASK™ 9 ColorMatch
design concepts to market. resin is pigmented to create
color-coded paper spool caps
for a Manhattan print house.

Assembly fixtures
cast in TASK™ 8 are
heat-resistant up to
263°F/129°C.

TASK™ 7 Flame Out™

meets UL 94 V-O requirements. It self
extinguishes once the flame is removed. Learn more at: www.smooth-on.com
27
 Polyurethane Plastic
TASK Series ™
TASK™ 18 resin is very
High Performance Casting Resins rigid. It is used to make
large vacuum form
molds for making
TASK™ 11 - Semi-rigid resin originally developed for high impact custom communications
tooling (drop hammer punch). It also offers good abrasion and satellite covers for
chemical resistance. Lucent Technologies.
TASK™ 12 - Semi-rigid urethane tooling resin that offers
extraordinary handling strength and impact resistance. Used for a
variety of industrial applications including making prototype models,
high impact parts and tools.
TASK™ 13 & TASK™ 14 - High impact resistance, low cost, semi-rigid,
black plastics are used for a variety of industrial applications including
fast mold making, prototyping, durable miniatures, black-colored props
and special effects.
TASK™ 15 - Exhibits exceptional impact strength when
cast in thin-wall sections. TASK™ 15 features a gradual cure

HPerIfGorHmaEnRce
TASK™ 2 & 3
profile, making it ideal for rotational casting applications. H
low
∙
 igh strength,
viscosity
TASK™ 16 - Fast-setting Shore 80A/30D industrial urethane
that offers very high tear strength, impact resistance and
TASK™ 4
wear resistance. TASK™ 16 can also be rotationally cast for
lightweight foam filled castings.
V ∙
 ery strong in
thin-walled sections
TASK™ 18 - Relatively low viscosity aluminum filled
Highly impact resistant urethane resin that was developed specifically for TASK™ 5 & 6
TASK™ 15 is used for rotational making short run vacuum forming molds.
casting mannequin bodies that
∙
Lowest cost performance plastics anywhere

are durable, hollow and can take TASK™ 21 - Described by many as having similar TASK™ 7
a beating. performance and mechanical characteristics to ABS ∙
UL 94 V-0 Flame rated - fire resistant
plastic, with high compressive and flexural strength as
well as good shock absorbance. TASK™ 8
∙ High heat resistant urethane plastic
TASK™ 21 video phone TASK™ 9
prototype housing has ∙ COLORMATCH™ neutral amber for
similar performance color matching and pigmenting

ormance
properties to ABS plastic.
TASK™ 11 (Formerly C-1509)
P e r f
∙ Semi-rigid resin - good for dry food contact
TASK™ 13 & 14 (Formerly C-1515, C-1520)
∙ Black semi-rigid urethane casting resins
TASK™ 15
∙ Ideal for machine rotocasting
∙ High impact resistance
Semi-rigid TASK™ 13 used for the
controller housing for the Laser Rack™
performance power lifting monitor.
TASK™ 16
∙ Fast-setting semi-rigid resin
∙ High impact & abrasion resistance
HIGHER
TASK™ 16 is quick TASK™ 18 (Formerly C-1508)
setting, easily pigmented
and can be used to cast parts, props, ∙ Aluminum filled mass casting resin
etc. that are flexible and highly impact TASK™ 21
resistant. ∙ High compressive and flexural

Pressure resistant and shark proof

∙ strength - compares to ABS plastic
TASK™ 11 used to house deep ocean
signal transponders for US Navy.

Learn more at: www.smooth-on.com 28

Specialty Polyurethane
Plastic Crystal Clear Series ™
Water Clear & UV Resistant
Crystal Clear™ resins are unique water clear plastics that have been
used for years to create spectacular large scale display castings (10 tons
and larger), prototype models, lenses, ice effects for movie special effects
and much more. There are different working time/demold time formulas to
choose from depending on requirements. Impactful color effects are made
with SO-Strong™, UVO™ or Ignite™ colorants.

Crystal Clear™ 200 Crystal Clear™

∙ 161/2”hour cure time
resin used to cast
∙ - 3” (0.16 cm - 1.25 cm) thick 8 ft. (2.4m) tall Buddha
that resides high on
Crystal Clear™ 202 a hilltop overlooking Highly detailed David
∙ 901/16”minute cure time Hong Kong. bust created with 8 ft. (2.4m) tall colored
∙ - 1/2” (1.25 cm - 7.5 cm) thick Crystal Clear™ resin. Crystal Clear™ 220 Christmas lights outside
Radio City Music Hall in New York City.
Crystal Clear™ 204
∙ 483” -hour
SMASH!™ Breakaway Plastic
cure time
∙ 6” (7.5 cm - 15.25 cm) thick
Crystal Clear™ 206
∙ 7Greater
day cure time SMASH!™ Plastic is a urethane liquid plastic designed to shatter/crumble
∙ than 6” (15.25 cm) thick on impact (“breakaway glass”). SMASH!™ is water clear and, once fully cured,
shatters like glass. It can be cast solid in thin sections to make window panes or
Crystal Clear™ 220 rotationally cast to form hollow bottles, jars or other glass-like objects to be used
∙ MUST BE HEAT CURED as breakable props for film and stage productions.
∙ Harder - easier to polish
Crystal Clear™ 222 Over six tons of SMASH!™ Plastic were used in the James Bond film, ‘Die Another Day,’
∙ Mercury Free including a scene where 007 drives his Aston Martin through huge
∙ MUST BE PRESSURE CAST ice palace doors made of SMASH!™ Plastic.
∙ MUST BE POST CURED SMASH!™
Plastic is
fe”
“Actor-Sa

Simply
SMASH! -ing!
™

Die Another Day © 2002 Damjaq, United

Artists Corporation. All rights reserved.

29 Learn more at: www.smooth-on.com

 Specialty Polyurethane
KX Flex ™
Plastic
Fast Setting Urethane Casting Elastomers
KX Flex™ 60 and 90 urethanes are fast setting two-component systems that
cure quickly to semi-rigid plastics that are very tough and impact resistant.
Cured plastic is off-white when cured and these products are very easy to color using
SO-Strong™, UVO™ or IGNITE™ colorants.
KX Flex™ 60 60A durometer Make It Fast – Make It Tough: They are used for a
∙ ∙
2.5 minute pot life 20 minute handling variety of applications including making fast-cure molds,
fast model duplication, prototypes, durable miniatures,
KX Flex™ 90 90A durometer props and special effects.
∙ 2.5 minute pot life ∙ 20 minute handling

Simpact ™
Ultra Tough
Simpact™ 60A, 80A & 85A are low odor, fast-setting urethanes that offer
very high tear strength, impact resistance and wear resistance. They are
phthalate-free, mercury-free and MOCA-free. Cured urethanes have
exceptional performance characteristics and dimensional stability.
Simpact™ 60A, 80A & 85A can be colored with SO-Strong™,
UVO™ or Ignite™ colorants. They are suitable for making
impact resistant props, prototypes and display pieces.
Simpact™ urethanes are on the border between being a rubber
and a plastic. This attributes to their toughness and durability, and
makes them a favorite among aquarium customers.

Plasti-Paste™ II Plasti-Paste II,

™

Trowelable Plastic Paste Fully Paintable!

Plasti-Paste™ II is a low-cost fiber-filled resin that holds a vertical surface without
sagging and cures to a strong, durable and lightweight plastic. Developed
originally as a mother mold material, this plastic can also be used for
creating themed environments or special effects.
Cured plastic can be sanded, machined and
painted with acrylic enamel paints.

Shell Shock™ Plasti-Paste™ II holds a vertical

surface without sagging for making
lightweight mother molds.
Brushable Liquid Plastic
Shell Shock™ FAST and SLOW are thixotropic plastics
that self-thicken when mixed and can be brushed onto
a variety of surfaces or into rubber molds. Material cures Shell Shock™ Fast
∙ 3Fullminute pot life
at room temperature with minimum shrinkage to a hard,
durable plastic. Fully cured castings are rigid and can be ∙ cure 1 hour
sanded, primed and painted. Shell Shock™ is ideal for Shell Shock™ Slow
making fast, lightweight rigid molds for creating silicone ∙ 8Fullminute pot life
appliances and effects. ∙ cure 5 hours

Shell Shock™ rigid molds are used to create film-quality silicone masks.
Learn more at: www.smooth-on.com 30
Expanding Foams
FOAM-iT! Series ™
FOAM-iT!™ expanding foams are easy to use and cure rigid and strong.
They can be used as a lightweight casting material, backfill material for
encapsulation or to make hollow castings. You can color them with
SO-Strong™, UVO™ or Ignite™ colorants for a variety of art/craft,
industrial or special effects applications.
FOAM-iT!TM 5 and
Cast Magic BronzonkerTM powder
TM

produces a finished lightweight

casting in a matter of minutes
for a custom look.

Cast custom block of

FOAM-iT™ 8 is used as a
FOAM-iT!™ 26 machinable modeling board.

FOAM-iT!™ 15

FOAM-iT!™ 10

FOAM-iT!™ 8

FOAM-iT!™ 5
8 fluid ounces
(237ml) of liquid FOAM-iT!™ 4 BLACK
material was
poured for each FOAM-iT!™ 4
foam example
displaying the
volumetric rate FOAM-iT!™ 3
of expansion.

Expansion Rate Pot Life Expansion Rate Pot Life

FOAM-iT!™ 3 • 18 Times • 1 minute FOAM-iT!™ 10 • 6 Times • 1.5 minute
FOAM-iT!™ 4 • 14 Times • 1.5 minute FOAM-iT!™ 10 SLOW • 6 Times • 3.5 minute
FOAM-iT!™ 4 Black • 14 Times • 1.5 minute FOAM-iT!™ 15 • 4 Times • 1.5 minute
FOAM-iT!™ 5 • 10 Times • 1.5 minute FOAM-iT!™ 26 • 2 Times • 1.5 minute
FOAM-iT!™ 8 • 8 Times • 1.5 minute

31 Learn more at: www.smooth-on.com

 Expanding Foams
FlexFoam-iT! Series ™
FlexFoam-iT!™ expanding foams cure flexible and durable. They are
lightweight, versatile and easy to use. They can be used for padding/
cushion material, gasket material, or to make props and special effects.
Vibrant colors can be achieved by adding color pigments.
Incredibly realistic cinder blocks created using
FlexFoam-iT!™ X and SO-Strong™ tints.

FlexFoam-iT!™ 25

FL AM E
!
R ATED FlexFoam-iT!™ 23 FR

FlexFoam-iT!™17

TUFF !
STUFF FlexFoam-iT!™ 15

FlexFoam-iT!™ 14

FlexFoam-iT!™ X

PILLOTW
SO F ! FlexFoam-iT!™ VIII

FL AMDE!
R ATE FlexFoam-iT!™ 7 FR

PILLOTW
SO F ! FlexFoam-iT!™ 6
FlexFoam-iT!™
is used for realistic
FlexFoam-iT!™ V and lightweight
cosplay props.
TUFF
S T U F F! FlexFoam-iT!™ IV

FlexFoam-iT!™ III
Need a Silicone Foam?
Find Soma Foama™ on pg. 9!
Expansion Rate Pot Life Expansion Rate Pot Life
FlexFoam-iT!™ 3 • 15 Times • 35 second FlexFoam-iT!™ X • 6 Times • 50 second
FlexFoam-iT!™ IV • 13 Times • 30 second FlexFoam-iT!™ 14 • 4 Times • 60 second
FlexFoam-iT!™ V • 11 Times • 50 second FlexFoam-iT!™ 15 • 4 Times • 2 minute
FlexFoam-iT!™ 6 • 10 Times • 35 second FlexFoam-iT!™ 17 • 3.5 Times • 60 second
FlexFoam-iT!™ 7FR • 8 Times • 35 second FlexFoam-iT!™ 23FR • 2 Times • 90 second
FlexFoam-iT!™ VIII • 7 Times • 35 second FlexFoam-iT!™ 25 • 2 Times • 90 second
Learn more at: www.smooth-on.com 32
Polyurethane Accessories
SO-Strong™ Colorants
can be added to any Smooth-On liquid
urethane rubber, urethane plastic or
urethane foam. Choose from 12 colors
or mix them to create custom colors
in order to produce the desired
effect for your castings. SO‑Strong™
colorants can be combined with
Metal powders, URE‑FIL™ fillers, or
Cast Magic™ powders to create Castings Stay
amazing effects. Translucent!

Blue Yellow Green Orange Purple Red

PMS 300C PMS 102C PMS 336C PMS 021C PMS 2603C PMS 200C

Light Medium Dark White Brown Black

Flesh Flesh Flesh PMS WhiteC PMS 483C PMS BlackC
PMS 148C PMS 479C PMS 469C Available in a 9-pack Color Sampler.
Note: Pantone values are approximate.

Ignite™ Fluorescent Pigments

Ignite™ pigments make
Pigments That Resist Ultra Violet Light castings come alive.
The fluorescent or “glow”
UVO™ Colorants effect is maximized under
are highly black light.
concentrated;
offering excellent
dispersion and Magenta Orange White
consistent color.
A very small Green Purple Pink
amount will Yellow
Yellow Red Blue
color a large
amount of
liquid epoxy
or urethane.

Available in a
9-pack Color Sampler.

Available in a 9-pack Color Sampler.

33 Learn more at: www.smooth-on.com

 Polyurethane Accessories
CASTING FX
UreCoat
™
Indestructable Urethane Rubber Coating
Bonds To Many Surfaces Creating A Tough, Long Lasting, Flexible Coating!
Urethane Rubber • Latex Rubber • Metal • Resins • Foams • Wood • Fabrics etc...
UreCoat™ is a two-component liquid urethane that can be
applied in thin layers to surfaces with a brush. A small amount
goes a long way. Rubber cures to a strong, tough and flexible
coating that will bend and flex with any substrate.

UreCoat Matting Powder System

™ Coating can be colored for
unique painting effects.
Eliminates surface gloss/shine permanently because it is a coating created using
UreCoat™ that you can brush on or spray onto surfaces. It is a little complicated
thgiL lamroN to use and involves first mixing solvent (acetone or alcohol) with matting powder.
Cured UreCoat™ will bend Next, mix UreCoat™ (A+B) in the proper proportions in a separate container.
and flex with any substrate.
Finally, combine all components and mix thoroughly.

Metal Powders For Cold Casting

“Cold-Casting” is a term used to describe the process of mixing metal
powder with a resin and applying the mixture into a mold. Metal Powder
+ Resin produces a finished casting that gives the appearance and feel of
solid metal at a fraction of the cost of real metal.

Bronze

Brass Nickel/Silver
Aluminum Copper

Cast Magic™ Powders

Cast Magic™ Powders are the fastest way to make metal and glitter effects.
Create spectacular casting effects in a matter of minutes!
Create different color effects • Blueberry Pie • Marshmallow Cream
with each Cast Magic™! • Boysenberry • Metallic Green
• Bronzonker • Mustard Shimmer
• Cherry Fizz • Pearly Blue
Smooth Cast™ Smooth Cast™
ONYX™ 300
• Copper Tone • Pearly Green
Boysenberry
• Fish Scale Gold • Pig Iron Cast Magic™ Pig Iron and
• Flamus Red • Red Devil Smooth-Cast™ ONYX™ resin
• Gold Finger • Silver Bullet are used to create a luster and
rs • Gold Rush • Silver Ghost shine similar to real metal.
Cast Magic™ Powde trong™ • Grape Soda • Steel Blue
Combined With So -S
or UVO™ Colorants Ca
n Create • Magenta Pop • Teal Dream
ts!
Dazzling Effec

Learn more at: www.smooth-on.com 34

Polyurethane Accessories
Fillers & Additives
Quarry Tone™ Granite FX Filler Powders 10
Vari
Chooations to
se Fr
om!

Specially blended powders that can be added to some Smooth-Cast™ liquid

plastics or liquid rubbers to create realistic stone effects in finished castings.
There are 10 granite effect powders to choose from, each with its own particle
size and color. Quarry Tone™ Powders are the fastest way to create realistic granite and stone effects in minutes!

PHOSPHORESCENT POWDERS
AVAILABLE IN:
Cryptolyte™ UV Glow Additive
Purple Passion, Blue/Green, Cryptolyte™ causes castings
Mint Green,
Gre en, Electric Yellow, Creamsicle, to glow bright blue under a
Flamingo Pink, Bold Blue & Yellow/Green focused ultra violet light.

Phosphorescent Powders for Making “Glow In The Dark” Castings

Glow Worm™ powders can Normal
Light
be added to Smooth-On
liquid plastics, rubbers and
foams to create castings that
glow in the dark after being
charged with light.
Glow Worm™ powders will
glow in the dark at least
10 times longer than other
glow powders. UV (Black)
Light

XTEND-IT™ Dry gas blanket designed to extend the shelf life of

unused moisture sensitive polyurethane products.

Kick-iT!™ Designed to accelerate the cure time of liquid

urethane rubber products.

SO-FLEX™ II Softening agent that lowers the cured durometer

of Smooth-On urethane rubbers.

SO-CURE™ Accelerates the cure time of liquid urethane plastic

products to allow for faster demolding of castings.

Sun Devil™ Slows color change and physical degradation due to

UV exposure of many Smooth-On urethane products.

35 Learn more at: www.smooth-on.com

 Polyurethane Accessories
Fillers & Additives
URE-FIL™ fillers disperse easily in Smooth-On materials. Some
fillers are designed for cost-savings, others are designed for specific casting
effects or improved physical properties.

URE-FIL™ 3
is added to
reduce cost.

URE-FIL™ 5 is
added to resin to
URE-FIL™ 15 produce wood effects.
is added to
reduce weight.

URE-FIL™ 3 is a ceramic filler that will give plastic castings a ceramic or porcelain-like finish.
URE-FIL™ 7
URE-FIL™ 5 is a lightweight filler that is your best choice for achieving a wood effect with plastics. is added to resin to
produce amazing
marble effects.
URE-FIL™ 7 provides dimensional stability, economy & improved flame resistance.

URE-FIL™ 9 is a lightweight filler that can be added to urethane as a thickener for brush-on applications.

URE-FIL™ 11 is a fiber-based filler that can be added to all Smooth-On products to thicken for brush-on applications.

URE-FIL™ 15 micro-balloons that can be added to Smooth-On urethane plastics to create very light weight castings.

URE-FIL™ 17 are small grain aluminum pellets (400 micron).

URE-FIL 17 URE-FIL 19 Smaller grain pellets will settle into areas of detail better, reducing voids
between particles.

URE-FIL™ 19 are pure aluminum pellet fillers (1200 micron) used with
liquid epoxy and urethane resins to improve thermal conductivity,
Actual Size dimensional stability, reduce shrinkage in large mass castings, etc.

URE-FIL™ 19 large grain

aluminum pellets are used
to make resin jewelry.

36
Laminating &
Surface Coat EpoxAmite Series ™
Epoxies Laminating System
The EpoxAmite™ Epoxy Laminating System is an
easy-to-use liquid epoxy system formulated for
a wide variety of fabrication applications. The
EpoxAmite™ Laminating System is unfilled, low in
viscosity, odorless and cures at room temperature.
Cured epoxy displays exceptional physical and
performance properties. It can be sanded, shaped,

Three s
machined, drilled, tapped and painted.

Speed Mix

The EpoxAmite™ Epoxy Laminating System can be used with

reinforcements such as S-Glass, E-Glass, Kevlar and carbon fibers for lay-up
applications or composite parts. EpoxAmite™ can also be mixed with fillers
such as URE-FIL™ 9 for gel coat applications. URE-FIL™ 3, URE-FIL™ 7 and
other fillers can be added for fairing, filleting or bonding applications.

EpoxAmite™ 101 Fast

∙ 116-8minute pot life Apply
∙ hour demold time
EpoxAmite™ 102 Medium
∙ 22 minute pot life
∙ 10-15 hour demold time
EpoxAmite™ 103 Slow
∙ 55
∙
minute pot life EpoxAcoat Series ™
24 hour demold time
EpoxAmite™ HT
Surface Coat System
∙ 60 minute pot life
EpoxAcoat™ is a thixotropic epoxy
∙ 24 hour demold time gel coat that is widely used for hand
EpoxAmite™ WHITE 101 Fast laminating/tooling applications.
∙ 20 minute pot life It is a tough & strong surface coat
∙ 10-15 hour demold time resin that cures at room temperature
EpoxAmite™ WHITE 102 Medium and offers exceptional abrasion
∙ 62 minute pot life resistance. EpoxAcoat™
∙ 20-24 hour demold time is easy to use, wets out
EpoxAcoat™ RED well over a variety of
∙ 20 minute pot life surfaces and will coat
∙ 16 hour demold time vertical surfaces
EpoxAcoat™ GREY without sagging.
∙ 20 minute pot life It is designed to
∙ 16 hour demold time complement
and work
EpoxAcoat™ NEUTRAL
∙ 20 minute pot life well with our
∙ 16 hour demold time EpoxAmite™
Laminating Ultratough EpoxAcoat™ RED
EpoxAcoat™ WHITE tool is ready to make composite
System (used
∙ 20 minute pot life parts for motorcycles.
∙ 16 hours demold time as a backup for
making tools, patterns,
EpoxAcoat™ HT fixtures, etc.).
∙ 40 minute pot life
∙ 24 hours demold time

37 Learn more at: www.smooth-on.com

 Laminating &
XTC-3D ™
Surface Coat
High Performance 3D Print Coating Epoxies
XTC-3D™ is a protective coating for smoothing and finishing
3D printed parts. Coating self-levels and wets out uniformly
without leaving brush strokes. XTC-3D™ cures to a hard,
impact resistant coating that can be sanded, primed and
painted. It works with PLA, ABS, LayWOO, powder printed
parts and other rigid media. XTC-3D™ does not contain
VOC’s, phthalates or phosphates.
XTC-3D™ fills in striations
and eliminates 90% of
post finishing work.

EPSILON™ & Epsilon™ PRO

EPS Foam Coating Epoxy
XTC-3D™
EPSILON™ is a two-part thixotropic epoxy coating that self
∙ 103.5minute pot life
thickens for brushing onto a variety of surfaces without
sagging. This product was developed for fabricators that
∙ hour cure time
regularly coat EPS foam. Cured material is easily EPSILON™ w/ 101 Fast
sanded, primed and painted. When ∙ 1516 minute pot life
applying to vertical surfaces, EPSILON™ ∙ hour cure time
wets out uniformly. Only 2 layers EPSILON™ w/ 102 Medium
minimum are required to build ∙ 30 minute pot life
an adequate thickness and ∙ 24 hour cure time
provide an impact resistant Epsilon™ PRO
coating. Epsilon™ PRO is ∙ 22 minute pot life
semi-rigid, offering better ∙ 16 hour cure time
impact resistance. Tarbender™
∙ 45 minute pot life
∙ 16 hour cure time

Tarbender™
High Gloss Coating and Encapsulant
Tarbender™ is a UV resistant clear liquid epoxy that can be poured over a variety of
surfaces to provide a strong, high gloss coating. Parts A and B mix together and flow
easily. Tarbender™ epoxy cures at room temperature and offers high impact resistance.
Tarbender™ is an excellent wood bar top coating and can also
be poured over plaster, concrete, foam, fabrics, etc. You can use
Tarbender™ to encapsulate 3-D objects or
coat flat objects, paper and more.

Tarbender™ is ideal
for encapsulating objects.

Learn more at: www.smooth-on.com 38

Castable Epoxies
EpoxAcast Series ™
Castable epoxies are used for a variety of industrial
EpoxAcast™ 650 is used for applications. They are easy to use, contain no VOC’s and are
encapsulating sensitive
electronics. solvent-free. Compared to Smooth-Cast™ or TASK™ urethane plastics,
EpoxAcast™ epoxies are generally harder, have higher compression
strength as well as higher heat and abrasion resistance. They are also widely used
for electrical encapsulation and bonding applications.

EpoxAcast 650 Mineral Filled

A mineral filled general purpose casting epoxy that is
low-cost and versatile. It features a low mixed viscosity for
minimal bubble entrapment. Choose Fast, Medium or Slow catalyst
to fit your project. You can also use HT Hardener to give your castings
higher heat resistance. EpoxAcast™ 650 is used for making hard dies
for metal stamping as well as patterns and fixtures. It is also used
for electrical encapsulation to extend the life cycle and enhance the
performance of potted electronic devices. Available in off-white and black.
EpoxAcast™ 650’s high compressive strength makes it ideal for making stamping dies
that withstand 20 tons of pressure for production pressing of copper metal ornaments.

EpoxAcast 655 Aluminum Filled

An aluminum filled casting epoxy that is dimensionally stable
even when mass cast. It is thermally conductive and fully
machineable when cured. Choose Fast, Medium or Slow
catalyst to fit your project. You can also use HT Hardener
to give your castings higher heat resistance.
EpoxAcast™ 655 is used for making vacuum
forming dies, injection molds, foundry patterns
and tooling fixtures. EpoxAcast™ 655 is commonly
used for vacuum forming dies.
EpoxAcast™ 650 Fast
∙ 20 minute pot life
∙ 1 hour demold time EpoxAcast 670 HT High Temp EpoxAcast™ 670 HT is used to make
prototype high heat injection molds.
EpoxAcast™ 655 Fast EpoxAcast™ 670 HT offers exceptional high
∙ 30 minute pot life temperature resistance to 350°F / 177°C and
∙ 3 hour demold time low shrinkage. It is used for making high
EpoxAcast™ 670 HT temp resistant industrial parts and tooling,
∙ 324hour pot life high-speed hard rollers, prototype injection
∙ MUST BEdemold
hour time molds, vacuum forming dies and fixtures.
∙ HEAT CURED
EpoxAcast™ 690
∙ 524hour pot life
∙ hour demold time EpoxAcast 690 & 692
EpoxAcast™ 692
∙ 12 hour72pothourlifedemold time Clear Castable Epoxy
∙ A clear casting epoxy that is ideal for making clear
jewelry/beads or replacement lenses for kit cars,
etc. Color with with UVO™ or IGNITE™ colorants
or add Cast Magic™ powders for different effects.
Also suitable for making prototype parts.

“River” table is created using

EpoxAcast™ 692 for deep pour EpoxAcast™ 690 is perfect
castings up to 2 inches. for resin jewelry craft.

39 Learn more at: www.smooth-on.com

 Epoxy Putties
Free Form ™ ™
Black & Fire Safe Epoxy Putties
are mix-by-hand putties that are used to create textured and highly detailed
display pieces. Both Habitat™ Epoxy Putties are solvent-free and contain no
VOC’s. They cure to a very hard, heat resistant material that is easily painted.
Habitat™ Epoxy Putties are suitable for interior and exterior use. They are
certified ‘aquarium safe’ and are used by aquariums to create hyper-realistic
coral and other aquarium displays. Habitat™ Epoxy Putties are also used for
general sculpting and theming applications. Free Form™ Habitat™ Fire Safe™
is flame rated (E84, Class A).

Use with Habitat™ Folding Powder –

fold powder into epoxy putty to thicken and reduce
stickiness; making the epoxy easier to handle.
Free Form™ Habitat™ is also an excellent repair cement
and bonds permanently to itself, PVC, Plexiglas® (acrylic),
wood, many metals, plastics and foams.
This automobile-sized iguana was created
with Free Form™ Habitat™ Fire Safe™ over a
Once applied, Habitat™ Epoxy Putty can be stamped with a silicone rubber stamp foam core by Stephen Kesler, TUSK Sculpture
to create patterns with intricate detail over a large surface area.

Free Form ™ ™
Flex FR Free Form™ Habitat™ Black
∙ 60
Flame Rated Flexible Epoxy Putty minute pot life
∙ 16 hour demold time
Free Form™ Habitat™ Flex FR is a semi-rigid version of the very rigid Habitat™ Free Form™ Habitat™ Fire Safe™
products and has some flexibility ∙ 90 minute pot life
when cured depending on thickness ∙ 16 hour demold time
and configuration. This product is Free Form™ Habitat™ Flex FR
certified flame resistant to the highest ∙ 90 minute pot life
testing standard (E84, Class A) and is ∙ 24 hour demold time
the only semi-rigid epoxy of its kind to Habitat Cast N Coat™
have this rating. ∙ 85 minute pot life
∙ 16 hour demold time

Cast N Coat™
Flame Rated Castable and Brushable Epoxy
is a heavily filled, pourable epoxy that can also be
thickened with Habitat™ Folding Powder for
brushing or troweling onto vertical surfaces. It
certifies to the highest flame rating (E84, Class A),
making it especially suited for public space fabrication
applications. Like other Habitat™ epoxies, it is safe
to be used in aquariums or in proximity to animals/
reptiles (zoo fabrication). Habitat Cast N Coat™
bonds to a variety of materials and can be applied as a fire rated,
protective/decorative coating to a variety of surfaces including
EPS foam. It cures to a durable plastic that can be machined,
sanded, painted, etc.

Learn more at: www.smooth-on.com 40

Epoxy Putties
Free Form AIR ™
Lightweight Epoxy Putty
Free Form™ AIR is suitable for an infinite variety of industrial
and art-related applications. This low-odor, low shrinkage
putty is unique, inexpensive and easy to use. Use to make rigid
support shells or mother molds, as a filleting material in epoxy
tooling, or in between layers of EpoxAmite™ and fiberglass
cloth, carbon or other fiber for making lightweight composites.
Free Form™ AIR HT is capable of withstanding
400°F / 204°C (post cure required) for use in
laminating and tooling applications.
Free Form™ AIR Fire Safe was
developed for theming
1. MIX companies that require fire
rated materials for making
public space theming
elements. It certifies to
the highest flame rating
available (E84, Class A). It
2. PRESS INTO THE MOLD has a higher density overall
and is a drier formulation
TM
that requires more effort to Free Form
Brand X
combine parts A and B. AIR Fire Safe

Free Form™ AIR FAST cures in minutes to a hard, strong and

extremely lightweight epoxy. Used at room temperature,
3. DEMOLD working time is 6 minutes in a 60 gram mass (2 oz) and
handling time is 30 minutes (tack-free, hard surface).

4. COLOR WITH ACRYLIC PAINTS

Free Form™ AIR

∙ pot life varies by mass*
∙ 24 hour full cure
Free Form™ AIR Fire Safe
∙ pot life varies by mass*
∙ 24 hour full cure
Free Form™ AIR HT
∙ pot life varies by mass*
∙ 16 hour full cure Free Form™ AIR FAST used
to seam 3D printed helmet
Free Form™ AIR FAST
∙ pot life varies by mass*
∙ 24 hour full cure
*See Technical Bulletin For More Information

The Mandalorian Helmet: DamaskProps 12/29/2019 - www.thingiverse.com/DamaskProps

License: The Mandalorian Helmet by Damask Props is licensed under the
Creative Commons - Attribution - Non-Commercial - No Derivatives license.

41 Learn more at: www.smooth-on.com

 Epoxy Putty &
Free Form SCULPT ™
Accessories
Epoxy Sculpting Putty
is a sculptable epoxy clay that
requires no firing and will
self-cure in a short time to an
extremely hard and durable Free Form™
state with virtually no shrinkage.
Free Form™ SCULPT is 30% lighter
than similar products and holds vertical
Detailer
is a low viscosity liquid
surfaces better. It has an ultra fine particle that makes adding details
size that gives the user the ability to sculpt and effects to the surface
finer detail with better precision using tools of Free Form™ SCULPT
or shaping by hand. epoxy putty easy.
Free Form™ SCULPT
∙ pot life varies by mass

Plasti-Paste™ EPOXY ∙ 24 hour full cure

Plasti-Paste™ EPOXY
∙ 40 minute pot life
Fiber Filled Trowelable Epoxy ∙ 16 hour demold time

Designed for vertical surface application,

Plasti‑Paste™ EPOXY is fiber filled and
can be used as a "mother mold" material
to reinforce rubber molds. This resin is
also a powerful adhesive and can be used
as a repair material for a variety of industrial
applications. Cured plastic can be sanded,
machined and pigmented. Plasti‑Paste™
EPOXY can be painted with acrylic enamel paints.

Flexer™Epoxy Flexibilizer
Flexer™ Epoxy Flexibilizer is a clear, low viscosity liquid additive
that will lower the durometer (Shore hardness) of some
Smooth-On casting and laminating epoxies. When added to the
epoxy system in the proper proportion, the cured epoxy will
be softer and, in some cases, can be made semi-rigid. Flexer™
will lower the viscosity of the epoxy system, improves wetting
capability (for laminating) and filler load capacity.

Epic ™
Epoxy Thinner E-POX-EE™
Epic™ Epoxy Thinner is a clear, water-like liquid that will
lower the viscosity of Smooth-On casting and laminating
epoxies. Epic™ will also aid in reducing bubble entrapment.
KLEENER
E-POX-EE KLEENER™ is a unique
Epic™ IS NOT A SOLVENT, is not hazardous and contains industrial hand cleaner made especially
no VOC’s or phthalates. Solvents that are commonly used to for removing unreacted liquid epoxy,
thin epoxies cause shrinkage. Epic™ is 100% reactive fluid, polyester, urethanes and other resins
does not evaporate and does not cause shrinkage. from the skin. It will also remove liquid
Lowers the Viscosity of Epoxies for: paint, lacquer and grease.
• Laminating • Casting • Infusion
Learn more at: www.smooth-on.com 42
Adhesives
Metalset™ A4 Metalset A4 ™
specified by all branches
of the U.S. military. Metal-Filled Epoxy Adhesive
A powerful metal-filled epoxy that bonds to porous
or non-porous surfaces and can be applied to vertical
surfaces without sagging. Cured epoxy can be
machined, sanded, etc. Metalset™ A4 has been used
for years by all branches of the U.S. Military.

Super Instant™ Rapid Epoxy Adhesive

A two component, clear amber adhesive
designed to provide rapid bonding. Curing
takes place quickly enough to permit handling
in 5 to 10 minutes at room temperature.
Super Instant™ adheres to metals such as
steel, aluminum and brass; and to wood, Super Instant™ Epoxy is also
glass, masonry and many hard plastics. available in 200ml cartridges.
See dispensing gun on page 50.

MT-13 ™
Premium Epoxy Adhesive
is a two-component, premium industrial epoxy for
applications requiring maximum holding power and
water resistance. MT-13™ is widely used by the
boating industry for assembly and general repair.

EA-40 ™
Epoxy Adhesive and Laminating Resin
A low viscosity epoxy that can be used for assembly and repair
applications. Bow makers know EA-40™ as an easy to use, reliable
laminating resin.
EA-40™ is used worldwide for creating
strong, flexible, and lasting custom bows.

PC-3 ™
Laboratory Tabletop Epoxy Adhesive
Black tabletop cement is a general purpose epoxy designed to
permanently bond and caulk sections of laboratory tabletops.

43 Learn more at: www.smooth-on.com

 Adhesives
URE-BOND
URE-B OND II ™
Flexible Urethane Adhesive
URE-BOND™ II is a premium performance urethane
adhesive that offers a strong flexible bond between
many different surfaces. URE-BOND™ II is ideal
for adhering polyurethane rubber to many types of
substrates (such as plaster, wood, cement, stone) and Ure-BOND™ II
non-porous materials (such as glass, hard plastics and a is being used to repair a
variety of metals). tear in a urethane mold.

URE-BOND™ 90
Urethane Adhesive
A two component, slightly expanding urethane adhesive that offers a strong,
rigid bond between many different surfaces. It is often used to bond segments of
tooling board as well as other porous and non-porous, rigid substrates.
URE-BOND™ 90 is used to adhere tooling
board pieces together to be cut as one.

URE-BOND™ 90 has allowed

scrap pieces of tooling boards to
be used to create an original model
which has a smooth and precise finish.
A scraper is used to spread the material evenly.

Black Panther™ 85
Flexible Black Urethane Adhesive
A two-component, fast curing liquid adhesive for repairing holes,
tears and splits in steel / fabric corded rubber conveyor belts,
providing high wear and abrasion resistance.

It also provides a strong,
Black Panther™ 85 flexible bond between a variety
is mixed 1:1 by of substrates including plaster,
volume and is poured wood, cement, stone, glass, hard
into the torn area. plastics and a variety of metals.
A scraper is used to level
Black Panther™ 85
over the torn area . Material is left to cure for 2.5 hrs.
and the belt is returned to service.

Sil-Poxy ™

Available in
Silicone Adhesive
convenient single Sil-Poxy™ is a one-component adhesive made specifically for bonding
application size! tin or platinum cured silicone rubber to silicone rubber and other substrates.

Learn more at: www.smooth-on.com 44

Sprayable Materials
EZ~Spray Silicone 20 & 22 ™
EZ~Spray™ Silicone 20 and 22 are platinum-cure silicones that
cure quickly to a soft rubber with high elongation and tear strength.
EZ~Spray™ Silicone 20 can be sprayed through the EZ~Spray™ Jr. spray
system. Both EZ~Spray™ Silicone 20 and 22 can be sprayed through other
spray systems. They cure with negligible shrinkage to strong, durable mold
rubbers good for production casting of polyester, epoxy or urethane resins,
gypsum, concrete and other materials.
EZ~Spray™ Silicone 20 and 22 are ideal for making fast, reusable vacuum
1. E Z~Spray™ Silicone 20 is
bags for producing composite parts.

g & R e s in In f usio n!
g in
t for Vacuum Bag
sprayed on the tool.

Per fec

2. The cured bag is removed. Resin gel coat 3. The bag is repositioned and resin is drawn 4. The cured composite car seat is removed
and glass are applied to the tool. in, saturating the glass. and ready for installation.

EZ~Brush™ Vac Bag

Brushable Version on page 11

EZ~Spray™ 35
EZ~Spray™ 35 silicone cures in one
hour with negligible shrinkage to
a durable mold rubber good for
production casting resins, foams,
plaster and other materials.

Silicone liners made with EZ~Spray™ 35 for repairing hundreds of grocery store refrigeration units.

EZ~Spray™ Rigid & Flexible Foams

EZ~Spray™ Rigid and Flexible Foams are
a polyurethane foam compound that can
be conveniently sprayed using Smooth-On’s
Sp eakers EZ~Spray™ Jr. spray system.
or EZ~Spray™ Foam cures quickly to a strong,
o

lightweight and impact resistant 8 lb. (approx.)

Foam Outd

rigid foam.
EZ~Spray™ FlexFoam cures quickly to a strong,
lightweight 7lb. (approx.) flexible foam.
Both can be painted and used for a variety of
special effects and industrial applications.

45 Learn more at: www.smooth-on.com

 Sprayable Materials
EZ~Spray StyroCoat ™ ™
Sprayable Plastic Foam Coating
Flame rated EZ~Spray™ StyroCoat™ plastic is
formulated to coat EPS foam economically. Dispensed
through Smooth-On’s EZ~Spray™ Jr. spray system,
the plastic cures in about 2 seconds and can be
applied to vertical surfaces without running off.
Cured plastic is lightweight, impact resistant
and can be sanded for priming and painting.
StyroCoat™ can also be sprayed into a rubber
mold to make fast, impact resistant castings.
StyroCoat™ plastic is used for theme design/
fabrication applications and making
movie/theater sets.

StyroCoat™ coated
foam pieces created
for the “Give Kids the StyroCoat™ coated
World” charity theme foam sculpture used for a
park, Kissimmee, FL. Broadway production of “Dracula.”

EZ~Spray 45 Urethane Rubber and

™

EZ~Spray Plastic
™
EZ~Spray™ 45 is a polyurethane rubber that
can be sprayed for making fast molds of large
surface areas. It cures overnight with negligible
shrinkage and is suitable for casting a variety EZ~Spray™ Plastic used
of materials. to create a mother mold/
EZ~Spray™ Plastic can be sprayed support shell.
over a rubber mold to create
“mother molds” or support
shells with high impact
resistance. Cured plastic
is lightweight, tough and
durable.

EZ~Spray™ Plastic can also

be sprayed into the mold to
Hyde Park Mouldings sculpted create the finished piece.
and cast several 7 ft. tall
(2.1 m) concrete fountains.
EZ~Spray™ 45
produced a flexible mold in a
matter of hours.

Learn more at: www.smooth-on.com 46

Polymer Modified Gypsum

Forton VF-812 ™
Forton™ VF-812 is a specially formulated, all
acrylic co-polymer which cross-links with a dry
melamine resin to make Forton™ MG moisture
resistant and UV stable. FMG™ is a unique
combination of high-strength alpha
hemihydrate gypsum with water-based
polymer chemistry that is reinforced
with “E” glass fiber. FMG™ is the first
technology to make gypsum an exterior
product, when painted or sealed, and
is certified as meeting the ASTM E-84,
Class A (or 1) flame rating for building
materials.

Sculptor Clay Williams uses

Forton™ MG and aluminum powder
to quickly make lightweight,
durable castings.

duoMatrix™-G
duoMatrix™-G is a polymer additive system for alpha gypsums that greatly
enhances physical properties. Castings are stronger, lighter, weather resistant
and can be demolded four times faster. Its versatility
allows adding of metal powders and other fillers to
simulate the look of metal, stone and other facades.
duoMatrix™-G can also be pigmented and painted.

duoMatrix™ NEO
An easy-to-use version of duoMatrix™-G, the dry
duoMatrix™-G is strong
and lightweight.

components of NEO (Part A) are “pre-measured” for

easy mixing with liquid latex (Part B). Easy two-to-one
by volume mix ratio means no scale is
required. NEO can be used to make
Matrix Dryve ™
lightweight pieces that are very strong
and water-resistant. NEO is also flame
Dry Polymer Modified Gypsum
resistant; meeting the ASTM E-84, Matrix Dryve™ is an “all-powder” alternative to
Class A (or 1) flame rating for our original duoMatrix™ NEO powder/liquid
building materials. system. Dryve™ is easy to use and can be cast
solid, slush cast, rotationally cast, laid up by
hand with chopped glass fiber or sprayed.
Fully cured pieces are strong, water-resistant
and can be painted, sanded, machined and
more. Dryve™ certifies to the highest flame
duoMatrix ™ castings are
weather resistant rating (ASTM E-84, Class A), making it suitable
and durable. for building materials.

47 Learn more at: www.smooth-on.com

 Polymer Modified Concrete

VF-774 Additive For GFRC

Forton™ VF-774 is an all acrylic thermoplastic co-polymer emulsion
that significantly improves long-term physical properties of glass
fiber reinforced concrete (GFRC) and complies with PCI MNL 128,
Recommended Practice, Appendix L for curing admixtures used in
GFRC. Forton™ VF-774 also eliminates the 7-day wet cure required
to achieve the maximum strengths of the GFRC matrix at 28 days.

Additional Benefits of Forton™ VF-774 include:

• Reduces crazing and drying shrinkage cracks
• Improved workability of the mix at low water/cement ratios Forton™ VF-774 enhanced architectural elements created
• Reduces moisture absorption by Willis Construction for the Citrus Tower Corporate Plaza
• UV stable in Riverside, California.
• U
 niform distribution of pigments for
batch to batch color consistency.

COMPLIANT &
SUPPORTED
WITH 20
YEARS OF
Forton™ Enhanced GFRC offers faster turnaround, lower labor TEST DATA
costs and endless design possibilities.

duoMatrix -C ™
duoMatrix™-C is a polymer additive for concrete that greatly enhances physical
and performance characteristics. duoMatrix™-C greatly reduces water/salt
absorption and virtually eliminates microcracks. Freeze/thaw, chemical
and UV resistance are also enhanced, and duoMatrix™-C also
eliminates the usual 7-day post cure.

duoMatrix™-C produces architectural items that stand

up to the most extreme environmental conditions.
Learn more at: www.smooth-on.com 48
Sealers &
Release Agents Sealers
SuperSeal™ Economical, low viscosity, fast-drying sealing agent
Liquid Sealer for a variety of surfaces that can be easily washed off.
Sonite™ Soft paste wax used to seal highly porous surfaces such as concrete.
Wax Will aid in releasing mold rubber from a variety of surfaces.
Ease Release™
Liquid wax designed to seal with minimal wax build-up.
2831
Convenient, economical liquid that seals porous surfaces
One Step™
and releases urethane rubber in a single step.

Release Agents
In & Out™ II
Concrete Release Agent
A water soluble release agent that aids
in releasing concrete or gypsum plaster
castings from Smooth-On rubber molds.
Mann release agents cover many applications. Aerosol and In & Out™ II provides a clean, positive
non-aerosol, solvent based or water based; made especially release and does not interfere with or
for mold making and casting. affect surface detail and helps minimize
air bubbles in finished castings.
Releases silicone from silicone.
Ease Release™
Used with silicones, urethanes, & resins.
200
A truly unique release agent.
Ease Release™
300
Used with urethane elastomers & epoxy.
AquaCon™
Ease Release™ Used with EPDM, urethane
400 & synthetic elastomers. Concrete Release Agent
Ease Release™ PTFE Teflon® based dry film mold release
AquaCon™ is a water based
500 & dry lubricant.
concrete release agent that
Ease Release™ Used with thermoplastics, melamine aids in releasing concrete
700 & polystyrene resins. castings from Smooth-On
rubber molds and other
Ease Release™ Used with urethane elastomers surfaces such as melamine,
2300 & epoxy (high viscosity). metal and non-porous
Ease Release™ Solvent-based soap release for (sealed) wood. It provides a
2310 urethane elastomers. clean, positive release, does
not interfere with color or
Ease Release™ surface detail and helps
Wax based release for urethane foam.
2831 minimize bug holes
and air bubbles in
Ease Release™ Heavy duty release for production finished castings.
2910 casting of urethane elastomers. Using AquaCon™ Without AquaCon™

Universal™ Mold Release

Made for mold making Kwikee™ Sprayer
and casting with urethane An economical alternative to aerosols
rubber and plastic. for dispensing liquid release agents and
sealing agents, the Kwikee™ Sprayer
delivers sealing agent or release agent
in a fine mist.

49 Learn more at: www.smooth-on.com

 14” (35.56 cm)
Equipment
Vacuum Chambers
Vacuum Chambers are used for removing air from
high viscosity materials like silicone rubber before pouring.

15” (38.1 cm)

They are also ideal for vacuum degassing liquid plastics such
as Crystal Clear™ plastic for making bubble free castings. The
vacuum chamber is made from tough aluminum and the lid is
made from shatter resistant acrylic. It can accommodate up to a
5 gallon pail. Vacuum pump not included.

12.5” (31.75 cm)

Pressure Chambers
Pressure Chambers are used for pressure casting liquid
rubber and liquid plastics. Pressure casting resins is
optimal for creating castings that are truly bubble free.
Recommended pressure for pressure casting is 60 psi.
Maximum pressure is 80 psi.
Compressor not included.

15.25”
(38.74 cm)
EZ~Spray™ Jr. Gun
EZ~Spray™ Jr. Gun is a versatile, convenient and easy-to-use spray
system for spraying 1,500 ml cartridges of EZ~Spray™ mold making 1,500 ml
and casting materials for large projects. Additional static mixers are cartridges
available. Compressor not included. (750 ml each)

Dispensing Guns
The 400 ml Dispensing Gun is available in both a manual and electric version. They
both force parts A & B through a static mixing tube by squeezing the handle of the
manual gun or pulling the trigger on the electric gun. The electric gun is excellent for
frequent molders and larger projects. Mold Star™ 16 FAST, Body Double™, Dragon
Skin™, Ecoflex™ are available, and other 400 ml cartridges can be used.
The 200 ml Dispensing Gun is available in a manual version only.
Super Instant™ Epoxy and other 200 ml cartridges can be used.

Turbine Mixer Reike Spout Valve Mixing Containers

Adapter Kit Mixing Containers with graduated
markings. Available in 16 oz., 32 oz.,
64 oz., and 165 oz. sizes.
Packaged in cases of 10, 50 or
100 containers.
165 oz.
64 oz.
32 oz.
Turbine Mixer has a 16 oz.
simple design, yet
does a better job of Designed to fit snugly inside the
mixing rubbers, plastics, and Reike brand pour spout which
foams than any mixer we’ve tried. comes equipped with all 5 gallon
It also mixes powder-based buckets of Smooth-On material.
Alja-Safe™ alginate and The kit permits the pail to be stored
Matrix™ NEO with fiber better, on its side for more accurate and
and is easy to clean. convenient pouring.
Learn more at: www.smooth-on.com 50
Kits
Skin FX Kits & Accessories
Create Realistic On-Skin Effects Quickly & Easily
Used By Hollywood Pros The # 1 Choice of Medical Simulation & EMS
Professionals Around The World
Ultimate Ultimate
Zombie Kit™ Wound Kit™ S ki
S il icn T it e ®
one
Ulti
mat
It 's
Ea sy
Skin
eW
To
ULTIMA Tite ® Gath
er yo
M ak
eY
oun
TE Z OSilicone ur su ou

1
From
rO

d Ki
pplie

Step
Kit:
It's Ea •Skin w nO
MB •Thi-V Tite ® s
sy To Ma n-

I E Kit Sk in

t
•Silc ex ®
ke Your •Ru Pig ® W ou
STEP
bb
Own •Mixin er Gla
nd s ST
On-Sk
ss ®
•Mixin g Stic
BY Mea In M
in Ef fec B EP
g Cu ks
ps sure in
ts In STEP out ut es
ST Y

2
Gathe
Minu before r you Skin ! EP

Step
Measu tes! which you r sup Tite ®
re out plie
are start. We s and
Skin Tite

Step 1
not
includ recomread the
® ed. mend Tec
hnical
Thick wearin
g vin Bulletins
en Sk yl glo

3
in Tite ® ves,

Step
Dispen
Adjus se a
you t the small am

es
want amou ou
to cre nt dep nt of
Add skin

Includ-Step
Dispense ate. end Skin Tite
color and the amo equal parts ing
Step 2

on the ® (1A
mix tho to creat unt dependinof Skin Tite ® Add size :1B by vol

es
roughl
e. g on the (1A:1B by
volum skin of the um
size of
co

4
Add wounde).
y the woun e). Adju lor an

Includ-Step
d you wantst the a few dro

Step
Add Thi seconSkin Tite ® ps of dm
-Vex® thic ds. . Thi
Mater Mix ma -Vex ® ix th
Step 3

kener ial wil terial silicon orou

ghly

y
l thic throro e thic
Appl

Step-B ide
ken ken
as it ughly for er to
y Sk is mix severathicken
in

5
ed.
Add Silc
color canPig ® Flesh pigm
Tite ® l

Step
to sk Add

Step-B ide
adding be adjusted ent to Skin in an
other Silc to matc Tite ® AdjusSilc Pig ®
Pig ® pigm h anyone'smixture. The d sc add tment “Flesh”
ents. skin color flesh
by
ulpt itional s in pig
small the fles ment
Apply Add a few amou htone to Ski

Gu
Skin Tite ® Skin Tite ® drops of Thi-V nts can n
of Silc be Tite ® mix
Allo
Step 4

to skin for sever . (8 drops were ex ®silicone

w Sk Pig ® made by ture.
and scu al secon added thick
here). Mixener to thick in Ti pigme add

6
ds. Mate Spread
lpt rial will en
thicken material thoro the wound mix ® te nts. ing

Gu

Step
Apply as it is mixe ughly ed
shape, mater wou
Skin Tite ® d. makin ial on
g the to skin.
nd to
Step 5

to skin Mix edg Scu cure

and scu Skin es hig lpt the
lpt Tite her
than material

7
® cen
with ter. into

Step
Spread
wound mixed material bloo
face withshapes and "peeonto skin. d pi Allow
popsicle ling flesh Sculpt the gmen Skin
Tite ®
stick). " (pull mate
material rial into t to cur
away from e for
Mix Ski Apply
mate Appl at lea
n Tite® help creat rial to uppe y bl
st 6
minu
Step 6

with bla e the illusi r cheek ood tes.

8
cure 5 While
ck pigme min. on of sunk bones and
bridg Add Skin mixt

Step
en eyes.
nt Allow e of nose to Silc Tite
Pig ® ® is cur ure
Add dep
material
to “Bloo ing
d” pig , Dispen
to wo
th to wo ment se und
Step 7

and Skin Tite

und usin mix ®
g dark thorou (1A:1B
color ghly. pbv).

While Spread
prev
Skin Tite ® iously appl to add the
thoroughl(1A:1B pbv) ied Skin Tite ® color mixed

To learn more about creating on-skin

y. . Add Silc is curin and mater
Pig ® Black g, dispense textur ial into
e.

To learn more about creating realistic on-skin

pigment more the
and mix cen
Apply ter of
black pigm the
depth. ente wound
Allow
Skin Tite ® d Skin Tite®
to cure to woun
for 5 minu ds to simu
tes. late

Zombie effects and to watch video wounds and to watch video tutorials showing the process,
tutorials showing the process, please visit www.smooth-on.com/woundkit
please visit www.smooth-on.com/zombiekit

Ultimate Blood™ Kit

The most realistic and versatile
liquid blood system available anywhere. It perfectly simulates human
blood in how it looks and flows. Ultimate Blood™ is ideal for creating
special effects, medical training and simulation, moulage or any
project in need of highest quality theatrical blood. You can
also change the viscosity of Ultimate Blood™
on the fly, and change color quickly
with color additives.

You have
ultimate control with
Ultimate Blood™
Please visit make it thicker, thinner
www.smooth-on.com/bloodkit and change color.
to learn more
about creating
realistic
blood effects.

To learn more
about creating skin effects
using our materials, visit our ever-expanding
Special Effects Makeup Tutorial Playlist:
www.smooth-on.com/skinfx
51 Learn more at: www.smooth-on.com
 Kits
Starter Kits
Starter Kits are a great way to introduce anyone to the world of mold making and casting! Print and online video
instructions take you step-by-step through the process. Great for inventors, artists, candle makers, students, arts &
crafts enthusiasts, and more!

POURABLE STARTER KIT:

The Pourable Silicone Starter Kit comes with everything you need to make
your first one or two piece block mold. Step-by-step instructions will guide
you through the process and best of all, the materials for making a mold in
which rubber is poured over your small model are included in the kit.
Includes:
• Trial Kit OOMOO™ 30 Molding Rubber
• Trial Kit Smooth-Cast™ 300 Casting Resin
Includes
• 2 oz. SuperSeal™ Sealing Agent A HOW-TO BOOKLET!
• Ease Release™ 205 Release Agent
• Quick Start Guide

LIFECASTING STARTER KIT:

This kit includes everything you need to make a mold of a
hand. Step-by-step instructions will guide you through the
process making it easy and fun to make a lifecast of anyone’s
hand! In no time you will have a perfect lifecasting which
will “freeze time” and create a long lasting memento.
Includes:
• Alja-Safe™ Molding Gel
• Casting Plaster
• Quick Start Guide

BODY DOUBLE™ STANDARD SET STARTER KIT:

Body Double™ is a long lasting platinum-cure silicone rubber that can be applied directly
to the skin to make molds of the face, hands and other body parts. The rubber cures
quickly and will reproduce perfect detail from any original model – far better detail
than any alginate! Starter Kit contains all supplies needed to
make a mold and support shell of a moderately sized
area of the body.
Includes:
• Body Double™ Silicone
• 2 Rolls of 4” Width Bandages
• Body Double™ Release Cream
• Mixing Sticks and Containers

FORTON ™
MG STARTER KIT:
Polymer Additive System for Alpha Gypsums
Forton™ MG is a unique combination of high-strength alpha hemi-hydrate
gypsum with water based polymer chemistry that is reinforced with “E” glass
fiber. Forton™ MG can be used for restoration and replication of natural façade
materials, architectural ornamentation, decorative arts casting, flower pots,
cold cast metal elements and sculpture. FMG can be slush cast (hollow), hand
laid-up, sprayed through the proper equipment or poured for solid casts.
Includes:
• 7 lbs VF-812 • 1 lbs MF-415
• 10 lbs FGR-95 • 22 grams Hardener
• 1 lb Chopped E-Glass
Learn more at: www.smooth-on.com 52
Latex
VERTICAL S
APPLICATION
Latex Know-How...
For Over 80 Years. HX-974™ is applied in
layers to make a mold of
an owl statue.
Holden’s Latex™ liquid latex mold making materials are good
for a variety of applications, including: Ornamental Concrete,
Brick Veneer, Stone Veneer, Candle Making, Mask Making and
Architectural Restoration.

HX-80™ Brushable Mold Making Latex Captures

is a vulcanizable, low viscosity latex featuring high
wear resistance and low shrinkage for concrete casting. Perfect Detail!
Best for making molds of 2-dimensional flat pieces for
architectural or decorative objects.

HX-407™ Pourable Mask Making Latex

is a pre-vulcanized, pourable latex that forms a thick
durable skin when poured into a gypsum mold and
allowed to “dwell” before spilling out to build layers.

HX-974™ High Viscosity Mold Making Latex HX-974™ makes

durable glove molds.
is a developed vulcanizable, high viscosity latex made
especially for vertical surface applications. With a
higher viscosity than HX-80™, this product is ideal for
making glove molds. The HX-974™ mold is
used to make a casting.
HX-200™ Coating/Dipping Latex
is a pre-vulcanized, low viscosity liquid that is Molds made with latex are highly elastic
widely used for different types of dipping/coating and exhibit good wear resistance when
applications and is good for making thin, stretchy casting abrasive materials like concrete.
skins. Sometimes referred to as ”balloon” latex.

HX-807™ Brushable Skin & Prop Latex Accessory Products from Holden’s:
is a pre-vulcanized, brushable latex that is suitable
for coating a variety of surfaces. Perfect for making • FabTone™ Latex Colorants
latex masks, skins and props. High viscosity allows • HX-Ceco Powder Latex Thickener ™
you to control thickness.
• HX-Barrier Coat™
HX-Injection Medium™ Latex • HX-Stiffening Agent™
is a low viscosity latex used for medical and
veterinarian training. Available in BLUE or RED, • HX-Castor Oil™ & more!
latex is injected into cadaver blood vessels to make
arteries and veins visible, aiding in identification.

HX-Body Latex™
is a premium grade Natural Liquid Latex
product for painting directly onto the
body to create a variety of skin effects
including paint-on clothing and costume effects.

HX-Cosmetic Latex™
is a natural latex compound that can be
used to create blemishes, burns, cuts,
wounds, wrinkles and similar skin effects.

53 Learn more at: www.holdenslatex.com

 Clays

The Finest Name in Modeling Clays

Sulfur-Free Fine Art Sculpting Clays
NSP™ holds exceptional surface details and is somewhat
waxier and tougher than other Chavant products. NSP™
can be melted and poured at approximately 205°F / 96°C.
Le Beau Touché™ is an extremely smooth sculpting fine
art plasteline with exceptional adhesive quality. The HTR
formula is suggested for use where working environments Industrial Design
are expected to reach 90°F / 32°C.
Modeling clay remains an industry
Sculptex™ is a non-drying modeling clay that is non- standard for three-dimensional
contaminating. It holds excellent detail and is great for design studies. The material perfectly
precision sculpting, prototyping and model making. complements modern CAD-CAM
Clayette™ modeling clay is non-hardening, odor free and processes and allows for quick surface
flexible without being sticky. It has a very smooth silky modifications.
surface texture. It is produced in a natural off-white color.
Monu-Melt™ brings all of the qualities of Clayette™ into
a formula that can be melted and applied to a CNC foam
armature by brush. Monu-Melt™ will not oxidize and can be
left out or heated and cooled repeatedly without any
significant change. This product can be melted at 180°F / 82°C.
Prima Plastilina™ is a premium-grade, smooth-working,
oil-based modeling clay that never hardens or changes
with air exposure. It has a medium tackiness with a
neutral, non-offensive odor and a natural tan color.
AUTOSTYLE & Y2 Klay are sulfur free,
Jolly King™ Plasteline offers the finest quality in an lightweight, low odor, and deaired.
economical plasteline. The wax base, which is used in
more costly plastelines, produces a smooth, pliable, CM-50, J-525 & CM-70 are sulfur
non-drying modeling material. based, hard, and available as deaired
or non-deaired.
Castilene™ models like clay and works like wax. It is
lightweight, compatible with silicones and other rubbers,
and can be melted and poured at about 180°F / 82°C. Ballistics Clay
Fill-It™ is a non-drying, wax-based clay with excellent
adhesive and feathering characteristics. It is used by mold
makers to seal mold boxes, build dams, set parting lines/ was established as a
shims and repair cracks. ballistic testing clay
in 1977. Since then,
Sulfur-Based Modeling Clays it has been adopted
by military and
Roma Plastilina™ sulfur-based modeling clay has been law enforcement
used by fine art sculptors since the 1950’s. agencies for
Professional Plasteline™ is a superior, sulfur based, evaluating body
silky smooth modeling clay. The material is soft, armor and helmets throughout the
permanently pliable, reusable and requires no heating. world. The clay is reliable, reusable
and easy to use.
Formulated in the 1920’s. DaVinci™ is an original Italian ROMA PLASTILINA™ No. 1 is specified
Plastilina. Normal temperature ranges do not affect this by National Institute of Justice (NIJ)
unique, wax-free, sculpting clay which has a non-sticky, Standard 0101.07 and ASTM E3004
smooth feel. for ballistics testing.
Learn more at: www.chavant.com 54
55
TECHNICAL

93
71
40
2

°C
e
n

s
)
24

o
.
ge

y
23
24
22
6
th
-41

e
/23

ati
ka

sit
D-
D-
D-
D-
D

./lb

F
r

°
ng r
n

Lif
d
r
i

3
CHARTS

co
n

r
. In e

re
lo

lu
ec

xR
x
or
r

TM
TM
TM
TM %
/in

r
o

u
ST

A:B
Mi
Mi
Vis ed
AS
Po
AS
Cu
@ 7 Tim
Sh
Ha e A
AS nes
Sp
Vo ific
(C m
Die
St Tea
A
El
at gatio
AS eak
Sh
(in
Co
Product Name
Mold Max™ 10 100:10 pbw 15,000 cps 45 min. 24 hrs. 10A 24.1 100 pli 529% 0.001 Light Pink
Mold Max™ 10T 100:10 pbw 14,000 cps 45 min. 24 hrs. 10A 25.4 87 pli 586% 0.0025 Translucent
Mold Max™ 14 NV 100:10 pbw 7,500 cps 40 min. 4 hrs. 14A 24.7 87 pli 600% 0.002 White
Mold Max™ 15T 100:10 pbw 20,000 cps 45 min. 24 hrs. 15A 25.6 94 pli 600% 0.002 Translucent
Mold Max™ 20 100:10 pbw 25,000 cps 45 min. 24 hrs. 20A 23.5 110 pli 512% 0.001 Light Pink
Mold Max™ 25 100:5 pbw 25,000 cps 60 min. 24 hrs. 25A 23.5 130 pli 375% 0.001 Purple
Mold Max™ 27T 100:10 pbw 30,000 cps 45 min. 24 hrs. 27A 25.0 110 pli 400% 0.002 Translucent
Silicone Rubber

Mold Max™ 29NV 100:10 pbw 10,000 cps 40 min. 6 hrs. 29A 23.7 96 pli 361% 0.002 Yellow
Mold Max™ 30 100:10 pbw 25,000 cps 45 min. 24 hrs. 30A 23.5 125 pli 300% 0.002 Pink

Tin-Cure Silicone Rubber

Mold Max™ XLS™ II 100:10 pbw 30,000 cps 40 min. 24 hrs. 30A 22.7 110 pli 375% 0.001 Blue
Mold Max™ 40 100:10 pbw 45,000 cps 45 min. 24 hrs. 40A 24.3 120 pli 250% 0.004 Mint Green
Mold Max™ 60 100:3 pbw 20,000 cps 40 min. 24 hrs. 60A 19.1 63 pli 132% 0.0015 Red
Mold Max™ STROKE™ 100:10 pbw Brushable 30-45 min. 16 hrs. 30A 23.5 125 pli 300% 0.002 White
OOMOO™ 25 1:1 pbv 4,250 cps 15 min. 75 min. 25A 20.6 40 pli 250% 0.0025 Light Blue
OOMOO™ 30 1:1 pbv 4,250 cps 30 min. 6 hrs. 30A 20.6 40 pli 250% 0.0025 Lavender
PoYo™ Putty 40 20:1 pbv Putty 3-5 min. 30 min. 40A 21.3 85 pli 250% 0.003 Light Pink
Body Double™ Standard Set 1:1 pbv Brushable 5 min. 20 min. 25A 23.7 N/A 500% <0.001 Purple
Body Double™ Fast Set 1:1 pbv Brushable 90 sec. 7 min. 25A 23.7 N/A 500% <0.001 Aqua Green
Body Double™ SILK 1:1 pbv Brushable 6 min. 20 min. 25A 30.4 N/A N/A <0.001 Green
Dragon Skin™ FX-Pro 1:1 pbv 18,000 cps 12 min. 40 min. 2A 25.0 61 pli 763% <0.001 Translucent
Dragon Skin™ 10 Very Fast 1:1 pbv 23,000 cps 4 min. 30 min. 10A 25.8 102 pli 1000% <0.001 Translucent
Dragon Skin™ 10 Fast 1:1 pbv 23,000 cps 8 min. 75 min. 10A 25.8 102 pli 1000% <0.001 Translucent
Dragon Skin™ 10 Medium 1:1 pbv 23,000 cps 20 min. 5 hrs. 10A 25.8 102 pli 1000% <0.001 Translucent
Dragon Skin™ 10 Slow 1:1 pbv 23,000 cps 45 min. 7 hrs. 10A 25.8 102 pli 1000% <0.001 Translucent
Water White
Dragon Skin™ 10 NV 1:1 pbv 6,000 cps 15 min. 75 min. 10A 25.8 90 pli 663% <0.001
Translucent
Dragon Skin™ 10 AF 1:1 pbv 23,000 cps 20 min. 5 hrs. 10A 25.8 102 pli 1000% <0.001 Translucent
Dragon Skin™ 15 1:1 pbv 21,000 cps 40 min. 7 hrs. 15A 25.8 112 pli 771% <0.001 Translucent
Dragon Skin™ 20 1:1 pbv 20,000 cps 25 min. 4 hrs. 20A 25.6 120 pli 620% <0.001 Translucent
Dragon Skin™ 30 1:1 pbv 20,000 cps 45 min. 16 hrs. 30A 25.7 108 pli 364% <0.001 Translucent
Ecoflex™ Gel 1:1 pbv 9,300 cps 15 min. 2 hrs. 000-35 28.0 N/A 1000% <0.001 Translucent

Platinum-Cure Silicone Rubber

Ecoflex™ Gel 2 1:1 pbv 5,000 cps 20 min. 50 min. 000-34 26.4 N/A 1000% <0.001 Translucent
Ecoflex™ 00-10 1:1 pbv 14,000 cps 30 min. 4 hrs. 00-10 26.6 22 pli 800% <0.001 Translucent
Ecoflex™ 00-20 1:1 pbv 3,000 cps 30 min. 4 hrs. 00-20 26.0 30 pli 845% <0.001 Translucent
Ecoflex™ 00-20 FAST 1:1 pbv 3,000 cps 20 min. 1 hr. 00-20 26.0 30 pli 845% <0.001 Translucent
Ecoflex™ 00-30 1:1 pbv 3,000 cps 45 min. 4 hrs. 00-30 26.0 38 pli 900% <0.001 Translucent
Ecoflex™ 00-31 Near Clear™ Water Clear
1:1 pbv 3,000 cps 40 min. 4 hrs. 00-31 26.0 38 pli 900% <0.001 Translucent
 C

93
71
2
e

°
n

24

o
y
ss

23
24
2
6
41

me
ag

e
/23

ati
g
k

sit
D-
D-
D-
D-
D-

Ti
r

./

ne
)

°F

R
B

Lif
d
r
lo

co
en r

r
n

re
ec 240

x
l

or
rin

. In

TM
TM
TM
TM th
B
TM %
/in

ix
73

i s
S
Co

A:B
M
Mi
AS
Po
AS
Cu
Sh
Ha e A
AS
Sp
Die lb.)
Str Tea
A
Sh

V ed
Vo ific

@
Elo
at gatio
AS eak
(in

(Cu ume
Product Name
Off-White
Ecoflex™ 00-33 AF 1:1 pbv 3,000 cps 45 min. 4 hrs. 00-33 26.0 38 pli 900% <0.001 Translucent
Off-White
Ecoflex™ 00-35 FAST 1:1 pbv 3,500 cps 2.5 min. 5 min. 00-35 26.0 38 pli 900% <0.001 Translucent
Water Clear
Ecoflex™ 00-45 Near Clear™ 1:1 pbv 2,000 cps 45 min. 4 hrs. 00-45 26.2 50 pli 980% <0.001
Translucent
Ecoflex™ 00-50 1:1 pbv 8,000 cps 18 min. 3 hrs. 00-50 25.9 50 pli 980% <0.001 Translucent
Ecoflex™ 5 (Cartridge Only) 1:1 pbv 13,000 cps 1 min. 5 min. 5A 25.8 75 pli 1000% <0.001 Translucent
Encapso™ K 1:1 pbv 150 cps 120 min. 16 hrs. 33A 28.6 N/A N/A <0.001 Clear
Equinox™ 35 FAST 1:1 pbv Putty 1 min. 7 min. 35A 22.2 140 pli 430% 0.001 Light Purple
Equinox™ 38 MEDIUM 1:1 pbv Putty 4 min. 30 min. 38A 22.2 140 pli 430% 0.001 Light Purple
Silicone Rubber cont.

Equinox™ 40 SLOW 1:1 pbv Putty 30 min. 5 hrs. 40A 22.2 140 pli 430% 0.001 Light Purple
EZ~Brush™ Vac Bag Silicone 1:1 pbv 20,000 cps 30 min. 3.5 hrs. 20A 25.7 102 pli Translucent
364% <0.001 Green

Platinum-Cure Silicone Rubber

Translucent
EZ~Spray™ Silicone 20 1:1 pbv 11,000 cps 3 min. 20 min. 20A 25.6 100 pli 470% <0.001 Green
Translucent
EZ~Spray™ Silicone 22 1:1 pbv 11,000 cps 5 min. 45 min. 22A 25.6 102 pli 450% <0.001 Green
EZ~Spray™ 35 1:1 pbv Sprayable 1.5 min. 1 hr. 35A 24.1 92 pli 415% <0.001 Purple
Mold Star™ 14T 1:1 pbv 11,000 cps 3 min. 9 min. 14A 25.6 90 pli 490% <0.001 Translucent
Mold Star™ 15 SLOW 1:1 pbv 12,500 cps 50 min. 4 hrs. 15A 23.5 88 pli 440% <0.001 Green
Mold Star™ 16 FAST 1:1 pbv 12,500 cps 6 min. 30 min. 16A 23.5 88 pli 440% <0.001 Blue-Green
Mold Star™ 19T 1:1 pbv 11,000 cps 3 min. 12 min. 19A 25.6 90 pli 470% <0.001 Translucent
Mold Star™ 20T 1:1 pbv 11,000 cps 6 min. 30 min. 20A 25.6 90 pli 470% <0.001 Translucent
Mold Star™ 30 1:1 pbv 12,500 cps 45 min. 6 hrs. 30A 24.7 88 pli 339% <0.001 Blue
Mold Star™ 31T 1:1 pbv 11,000 cps 5 min. 23 min. 30A 25.6 90 pli 400% <0.001 Translucent
Rebound™ 25 1:1 pbv Brushable 20 min. 6 hrs. 25A 23.5 102 pli 690% <0.001 Orange
Rebound™ 40 1:1 pbv Brushable 20 min. 6 hrs. 40A 23.5 106 pli 324% <0.001 Green
Rubber Glass™ 1:1 pbv 150 cps 120 min. 16 hrs. 33A 28.6 N/A N/A <0.001 Clear
Smooth-Sil™ 933 Flame Out™ 1:1 pbv 40,000 cps 45 mins. 6 hrs. 33A 19.5 50 pli 433% <0.001 White
Smooth-Sil™ 936 100:10 pbw 21,000 cps 60 min. 24 hrs. 36A 22.9 110 pli 500% <0.001 Blue
Smooth-Sil™ 940 100:10 pbw 35,000 cps 30 min. 24 hrs. 40A 23.4 100 pli 300% <0.001 Pink
Smooth-Sil™ 945 1:1 pbv 30,000 cps 25 min. 6 hrs. 45A 22.3 120 pli 320% <0.001 Purple
Smooth-Sil™ 950 100:10 pbw 35,000 cps 45 min. 18 hrs. 50A 22.3 155 pli 320% <0.001 Blue
Smooth-Sil™ 960 100:10 pbw 30,000 cps 45 min. 16 hrs. 60A 22.2 110 pli 270% <0.001 Green
Water Clear
SORTA-Clear™ 12 1:1 pbv 6,000 cps 40 min. 12 hrs. 12A 25.9 80 pli 590% <0.001
Translucent
SORTA-Clear™ 18 100:10 pbw 21,000 cps 60 min. 24 hrs. 18A 25.6 80 pli 545% <0.001 Translucent
SORTA-Clear™ 37 1:1 pbv 35,000 cps 25 min. 4 hrs. 37A 25.6 105 pli 400% <0.001 Translucent
SORTA-Clear™ 40 100:10 pbw 35,000 cps 60 min. 16 hrs. 40A 25.6 120 pli 400% <0.001 Translucent

52
56
57

°C
TECHNICAL

93
71
2

24
24

o
.)

23
ss

23
24
2
6
41

ty
/
e

e
a

/lb

ati
gth

si
D-
D-
D-
D-
D-

ne
)
r

CT

Lif
nk

d
In.

3°
r

M
M
CHARTS

co
n

en ar

r
.

re
lo

lu
/in ge

ec

xR
x
or
ri

TM
TM
TM %

e
r
o

ST
ST
t
(in

A:B
Mi
Mi
Vis ed
AS
Po
AS
Cu
Tim
@ 7e
Sh
Ha e A
A
Sp
Vo ific
(Cu me
D
S
A
El
at gatio
AS eak
Sh
Co
Product Name
Brush-On™ 35 1:1 pbv Brushable 20 min. 16 hrs. 35A 21.5 57 pli 1,000% <0.001 Grey-Green
Brush-On™ 40 1:1 pbv Brushable 20 min. 16 hrs. 40A 23.7 60 pli 1,000% <0.001 Off-White
Brush-On™ 50 1:1 pbv Brushable 20 min. 16 hrs. 50A 23.7 80 pli 400% <0.001 Off-White
Brush-On™ 60 1:1 pbv Brushable 20 min. 16 hrs. 60A 23.5 80 pli 400% <0.001 Off-White
Clear Flex™ 30 1:1 pbv 750 cps 15 min. 16 hrs. 30A 26.9 54 pli 675% 0.002 Clear
Clear Flex™ 50 1:2 pbw 250 cps 25 min. 16 hrs. 50A 26.8 25 pli 500% 0.0015 Clear
Clear Flex™ 95 1:1.5 pbw 250 cps 25 min. 16 hrs. 95A 26.8 200 pli 175% 0.0028 Clear
Econ™ 60 1:1 pbv 1,400 cps 6 min. 16 hrs. 60A 26.7 85 pli 500% <0.001 Amber Translucent
Urethane Rubber

Econ™ 80 1:1 pbv 1,200 cps 13 min. 24 hrs. 80A 26.2 77 pli 127% 0.0014 Translucent
EZ-Mix™ 40 1:1 pbv Brushable 18 min. 16 hrs. 40A 27.0 67 pli 577% <0.001 Grey
EZ~Spray™ 45 1:1 pbv Sprayable 20 min. 16 hrs. 45A 27.0 100 pli 375% <0.001 Light Blue
Formlastic™ 48 1:1 pbv 3000 cps 25 min. 24 hrs. 48A 24.3 98 pli 1250% 0.001 Off-White
Formlastic™ 60 1:1 pbv 3000 cps 40 min. 24 hrs. 60A 24.3 146 pli 1000% 0.001 Off-White
KX Flex™ 60 1:1 pbv 800 cps 2.5 min. 24 hrs. 60A 24.1 N/A 125% 0.005 Off-White
KX Flex™ 90 100A:120B pbw 800 cps 2.5 min. 24 hrs. 90A 24.1 N/A 125% 0.005 Off-White
PMC™-121/30 1:1 pbv 1,800 cps 30 min. 16 hrs. 30A 26.7 75 pli 1,000% <0.001 Clear Amber
PMC™-121/50 1:1 pbv 1,400 cps 30 min. 16 hrs. 50A 26.7 85 pli 500% <0.001 Clear Amber
PMC™-724 1:10 pbw 4,000 cps 20 min. 16 hrs. 40A 20.1 90 pli 700% <0.001 Off-White
PMC™-726 1:10 pbw 3,000 cps 25 min. 16 hrs. 60A 20.4 100 pli 400% <0.001 Light Tan
PMC™-744 2:1 pbv 3,400 cps 15 min. 16 hrs. 44A 27.5 90 pli 400% <0.001 Beige
PMC™-746 2:1 pbv 1,200 cps 15 min. 16 hrs. 60A 26.9 100 pli 650% <0.001 Amber to Blue
PMC™-770 2:1 pbw 3,000 cps 30 min. 16 hrs. 70A 26.5 200 pli 750% <0.001 Light Amber
PMC™-780 2:1 pbv 2,000 cps 25 min. 48 hrs. 80A 27.2 200 pli 750% <0.001 Light Amber
PMC™-790 2:1 pbv 3,000 cps 20 min. 48 hrs. 90A 25.9 300 pli 550% <0.001 Clear Amber
ReoFlex™ 20 1:1 pbv 1,800 cps 30 min. 16 hrs. 20A 27.3 60 pli 1,000% <0.001 Off-White
ReoFlex™ 30 1:1 pbv 1,500 cps 30 min. 16 hrs. 30A 27.5 82 pli 1,000% <0.001 Off-White

KEEP OUT OF REACH OF CHILDREN. WARNING: Known to the state of CA to

ReoFlex™ 40 1:1 pbv 1,500 cps 30 min. 16 hrs. 40A 27.2 85 pli 1,000% <0.001 Off-White

cause cancer, birth defects or other reproductive harm. www.P65Warnings.co.gov

ReoFlex™ 50 1:1 pbv 2,000 cps 50 min. 16 hrs. 50A 27.4 120 pli 435% <0.001 Off-White
ReoFlex™ 60 1:1 pbv 1,800 cps 50 min. 16 hrs. 60A 26.7 132 pli 581% <0.001 Off-White
VytaFlex™ 10 1:1 pbv 3,100 cps 30 min. 24 hrs. 10A 27.9 38 pli 1,000% <0.001 Off-White
VytaFlex™ 20 1:1 pbv 1,000 cps 30 min. 16 hrs. 20A 27.7 60 pli 1,000% <0.001 Clear Amber
VytaFlex™ 30 1:1 pbv 1,800 cps 30 min. 16 hrs. 30A 27.3 78 pli 1,000% <0.001 Off-White
VytaFlex™ 40 1:1 pbv 2,000 cps 30 min. 16 hrs. 40A 26.9 82 pli 660% <0.001 Off-White
VytaFlex™ 45 1:1 pbv 2,000 cps 30 min. 16 hrs. 45A 26.4 100 pli 900% <0.001 Off-White
VytaFlex™ 50 1:1 pbv 2,000 cps 60 min. 16 hrs. 50A 26.7 102 pli 400% <0.001 Off-White
VytaFlex™ 60 1:1 pbv 2,000 cps 60 min. 16 hrs. 60A 26.6 136 pli 480% <0.001 Off-White
 )

2
12

°C
°C

93
71
8
66

D-4

s
e

o
23
23

23
24
63
6
25

ty
TM

/
/

e
S

ati
F
A

si
D-
D-
D
D-
D-

./l
r

† A 38

Lif
n

t†
t

sile e

3°
3° e

M
M

co
n
r
. In e

re
lo

xR
x
or
ri

B ti

TM
TM
TM ak %n
TM
/in

s
cep
cep D-

i
ST
ST
S

A:B
Mi
Mi
V ed
AS
Po
A
Ha
Tim dling
@ 7e
Cu
@ 7 Tim
Sh
Ha e D
AS nes
Sp -2240
Voecific
(C lum
Ult b.)
Tenimat
A
(Ex
Elo STM D-
at nga 412)
A re o
(Ex
Sh
(in kag
AS )
Co
Product Name
Crystal Clear™ 200 100:90 pbw 600 cps 20 min. - 16 hrs. 80D 26.7 2,500 psi 10% 0.001 Clear
Crystal Clear™ 202 100:90 pbw 600 cps 9 min. - 90 min. 80D 26.7 3,500 psi 10% 0.0125 Clear
Crystal Clear™ 204 100:90 pbw 600 cps 2 hrs. - 48 hrs. 80D 26.7 3,500 psi 10% 0.002 Clear
Crystal Clear™ 206 100:90 pbw 600 cps 4.5 hrs. - 7 days 80D 26.7 2,500 psi 10% 0.002 Clear
Crystal Clear™ 220 100:75 pbw 675 cps 22 min. - overnight 85D 25.9 8,190 psi 12% 0.0173 Clear
Crystal Clear™ 221 100:75 pbw 675 cps 75 min. - overnight 85D 25.9 8,190 psi 12% 0.0173 Clear
Urethane Plastic

Crystal Clear™ 222 MF 100:75 pbw 800 cps 20 min. - 16 hrs 83D 25.9 8,990 psi 6.3% 0.0135 Clear
EZ~Spray™ StyroCoat™ 1:1 pbv Variable 2 sec. - 60 min. 80D 24.7 3,170 psi 20% 0.015 Off-White
EZ~Spray™ Plastic 1:1 pbv Variable 2 sec. - 3 hrs. 75D 25.0 2,650 psi 10% 0.016 Off-White
Feather Lite™ 1:1 pbv 410 cps 8.5 min. - 2 hrs. 58D 41.3 2,160 psi 1.6% 0.003 Beige
Plasti-Paste™ 1:3 pbv Paste 8-10 min. 90 min 24 hrs. 70D 23.9 1,600 psi 1.5% 0.005 Off-White
Plasti-Paste™ II 1:2 pbv Paste 10 min. 90 min. 24 hrs. 70D 27.73 2,150 psi 1.14% 0.005 Off-White
Shell Shock™ FAST 1:4 pbv 3,000 cps 3 min - 60 min. 85D 17.3 3,100 psi 0.4% 0.0006 Beige
Shell Shock™ SLOW 1:4 pbv 3,000 cps 8 min - 5 hrs. 85D 17.3 3,100 psi 0.4% 0.0006 Beige
Simpact™ 60A 1:1 pbv 1,100 cps 4 min. 2 hrs. 48 hrs. 60A 25.7 990 psi† 400% 0.007 White

KEEP OUT OF REACH OF CHILDREN. WARNING: Known to the state of CA to

†
Simpact™ 80A 100:60 pbw 2,000 cps 15 min. 4 hrs. 48 hrs. 80A 25.4 2,295 psi 164% 0.007 Amber

cause cancer, birth defects or other reproductive harm. www.P65Warnings.co.gov

Simpact™ 85A 85:100 pbw 1,100 cps 4 min. 2 hrs. 48 hrs. 85A 25.4 1,573 psi† 164% 0.007 Off-White
SMASH!™ Plastic 1:1 pbv 900 cps 5 min. 90 min. 16 hrs. 80D 26.7 N/A N/A 0.0001 Clear
Smooth-Cast™ 45D 1:1 pbv 250 cps 5 min. - 30 min. 45D 25.2 1,560 psi 100% 0.007 Translucent White
Smooth-Cast™ 57D 1:1 pbv 300 cps 3 min. - 30 min. 57D 26.4 2,420 psi 100% 0.012 Translucent White
Smooth-Cast™ 60D 1:1 pbv 430 cps 5 min. - 30 min. 60D 26.4 2,420 psi 100% 0.012 Translucent White
Smooth-Cast™ 61D 1:1 pbv 430 cps 7 min. - 60 min. 61D 26.4 2,420 psi 100% 0.012 Translucent White
Smooth-Cast™ 65D 1:1 pbv 120 cps 2.5 min. - 10-15 min. 65D 26.4 2,400 psi 20% 0.01 White
Smooth-Cast™ 66D 1:1 pbv 120 cps 7 min. - 60 min. 66D 26.4 2,400 psi 20% 0.01 Grey
Smooth-Cast™ 300Q 1:1 pbv 80 cps 30 sec. - 4-5 min. 70D 26.4 3,000 psi 5% 0.01 White
Smooth-Cast™ 300 1:1 pbv 80 cps 3 min. - 10 min. 70D 26.4 3,000 psi 5% 0.01 White
Smooth-Cast™ 305 1:1 pbv 80 cps 7 min. - 30 min. 70D 26.4 3,000 psi 7.5% 0.0065 White
Smooth-Cast™ 310 1:1 pbv 80 cps 15-20 min. - 3-4 hrs. 70D 26.4 3,000 psi 7.5% 0.0065 White

58
59
TECHNICAL

ty
n
CHARTS

si
2
n/i

1
°C
°C

co
93
7
8
66 )

e
e (i

o
23
24
63
25
g

/23
/23

Vis
e
ate

F
F

ati
D-
D-
D-
D-
ka

°
°
r

Lif
sile
m

3
3

M
M
M

n
. In e

re
lo

xR
xed
o
rin

n
B ion

TM ss
TM
TM

ST
ST
ST ak %

Sh
Ha re D

A:B
Mi
Mi
A
Po
A
Ha
Tim dling
@ 7e
Cu
@ 7 Tim
AS dne
Sp D-224
Voecific 0
(Culum
Ul ./lb.)
T
AS
Elo D-638
at ngat
A re
Sh
AS
Co
Product Name
Smooth-Cast™ 320 1:1 pbv 80 cps 3 min. - 10 min. 70D 26.4 3,000 psi 10% 0.01 Off-White
Smooth-Cast™ 321 1:1 pbv 80 cps 7-9 min. - 30 min. 70D 26.4 3,000 psi 8% 0.007 Off-White
Smooth-Cast™ 322 1:1 pbv 80 cps 10-20 min. - 2-4 hrs. 70D 26.4 3,000 psi 8% 0.007 Off-White
Smooth-Cast™ 325 1:1 pbv 100 cps 2.5 min. - 10 min. 72D 25.9 3,170 psi 10% 0.01 Clear Amber
Smooth-Cast™ 326 1:1 pbv 100 cps 7-9 min. - 60 min. 72D 25.9 3,170 psi 10% 0.0075 Clear Amber
Smooth-Cast™ 327 1:1 pbv 100 cps 10-20 min. - 2-4 hrs. 72D 25.9 3,170 psi 10% 0.0075 Clear Amber
Smooth-Cast™ ONYX™ FAST 1:1 pbv 100 cps 2.5 min. - 10-15 min. 80D 27.7 5,840 psi 4% 0.01 Black
Smooth-Cast™ ONYX™ SLOW 1:1 pbv 100 cps 5 min. - 90 min. 80D 27.7 7,660 psi 3% 0.012 Black
Urethane Plastic Cont.

Smooth-Cast™ 380 1:1 pbv 1,140 cps 6 min. - 60 min. 82D 15.9 3,550 psi 1.43% 0.0025 Tan
Smooth-Cast™ 385 1:5 pbw 3,000 cps 20 min. - 2 hrs. 85D 17.3 3,100 psi 1% 0.0006 Beige
TASK™ 2 1:1 pbv 150 cps 7 min. - 60 min. 80D 24.7 6,650 psi 6% 0.005 White
TASK™ 3 1:1 pbv 150 cps 20 min. - 90 min. 80D 24.7 6,650 psi 6% 0.0025 White
TASK™ 4 100:100 pbw 250 cps 20 min. - 16 hrs. 83D 23.9 6,500 psi 4% 0.0035 Ivory
TASK™ 5 1:1 pbv 600 cps 3 min. 15 min. 24 hrs. 77D 25.2 4,530 psi 5% 0.007 Tan
TASK™ 6 1:1 pbv 800 cps 7 min. 75 min. 24 hrs. 75D 25.9 5,200 psi 4% 0.0031 Tan

KEEP OUT OF REACH OF CHILDREN. WARNING: Known to the state of CA to

cause cancer, birth defects or other reproductive harm. www.P65Warnings.co.gov
TASK™ 7 Flame Out™ 1:1 pbv 200 cps 2.5 min. - 10 min. 73D 23.1 3,390 psi 15.1% 0.0111 White
TASK™ 8 1:1 pbv 100 cps 2.5 min. - 10-15 min. 80D 25.4 5,840 psi 4% 0.01 Off-White
TASK™ 9 1:1 pbv 300 cps 7 min. - 60 min. 85D 24.3 7,800 psi 6% 0.009 Clear Amber
TASK™ 11 100:100 pbw 2,000 cps 20 min. - 16 hrs. 60D 24.7 2,500 psi Translucent
100% 0.0024 White
TASK™ 13 100:120 pbw 800 cps 3 min. - 20 min. 50D 24.1 1,800 psi 125% 0.005 Black
TASK™ 14 100:120 pbw 800 cps 10 min. - 45 min. 50D 24.1 1,800 psi 125% 0.0035 Black
TASK™ 15 75:100 pbw 600 cps 6 min. - 60 min. 75D 24.7 2,720 psi 20% 0.0042 Opaque White
TASK™ 16 1:2 pbw 1,400 cps 6 min 90 min. 24 hrs. 30D 25.6 2,264 psi† 233% 0.0025 Light Yellow
TASK™ 18 26:100 pbw 4,400 cps 20 min. - 16 hrs. 88D 17.6 3,250 psi 1% 0.0006 Metal Gray
TASK™ 21 2:1 pbv 500 cps 6 min. - 60 min. 75D 25.9 5,500 psi 7.5% 0.0058 White
Task™ 23 FAST 100:60 pbw 3,500 cps 4 min. - 2 hrs. 63D 26 3,800 psi 400% 0.001 Neutral
Task™ 24 SLOW 100:60 pbw 3,500 cps 20 min. - 4 hrs. 65D 26 4,280 psi 400% 0.001 Neutral
 93
71

o
.)

y
23
24
on

e
ub

ati
ot

sit
D-
D-
./lb
r

nsi c

R
Lif
e
e
a
Fo ic

co
m

nd
. In e
lo

lu
p

ec

x
lu
s./C

TM
TM
p

ix
s
u

A:B
M
Mi
V ed
AS
Po
AS
Ha
Tim ling
De
Tim old
Sp
Vo ific
(C m
Ap
Vo rox.
Ex meri
Lb
Co
Product Name
FOAM-iT!™ 3 1:1 pbv 200 cps 1 min. 20 min. 2 hrs. 504 18 times 3 lb/ft3 Beige
3
FOAM-iT!™ 4 1:1 pbv 300 cps 1.5 min. 20 min. 2 hrs. 420 14 times 4 lb/ft Beige
FOAM-iT!™ 4 BLACK 1:1 pbv 300 cps 1.5 min. 20 min. 2 hrs. 420 14 times 4 lb/ft3 Black
3
FOAM-iT!™ 5 1:1 pbv 300 cps 1.5 min. 20 min. 2 hrs. 315 10 times 5 lb/ft Beige

Rigid
FOAM-iT!™ 8 2:1 pbw 300 cps 1.5 min. 20 min. 2 hrs. 194 8 times 8 lb/ft3 Off White

Rigid
3
FOAM-iT!™ 10 1:1 pbv 400 cps 1.5 min. 20 min. 2 hrs. 157 6 times 10 lb/ft Beige
FOAM-iT!™ 10 SLOW 1:1 pbv 400 cps 3.5 min. 1 hr. 4 hrs. 157 6 times 10 lb/ft3 Beige
3
FOAM-iT!™ 15 1:1 pbv 500 cps 1.5 min. 20 min. 2 hrs. 105 4 times 15 lb/ft Beige
FOAM-iT!™ 26 1:1 pbv 500 cps 1.5 min. 20 min. 2 hrs. 60 2 times 26 lb/ft3 White
3
EZ~Spray™ Foam 1:1 pbv 400 cps 13 sec. 10 min. 10 min. 144 7 times 8 lb/ft Tan
Urethane Expanding Foams

FlexFoam-iT!™ III 1:2 pbv 1,000 cps 35 sec. 25 min. 2 hrs. 504 15 times 3 lb/ft3 White

KEEP OUT OF REACH OF CHILDREN. WARNING: Known to the state of CA to

3

cause cancer, birth defects or other reproductive harm. www.P65Warnings.co.gov

FlexFoam-iT!™ IV Tuff Stuff 80:100 pbw 1,000 cps 30 sec. 45 min. 2 hrs. 420 13 times 5 lb/ft White
FlexFoam-iT!™ V 1:1 pbv 1,000 cps 50 sec. 45 min. 2 hrs. 315 11 times 5 lb/ft3 White
3
FlexFoam-iT!™ 6 Pillow Soft 1:1 pbv 1,000 cps 35 sec. 60 min. 2 hrs. 280 10 times 5 lb/ft White

Flexible
FlexFoam-iT!™ 7 FR 1:1 pbv 1,000 cps 35 sec. 60 min. 2 hrs. 229 8 times 7 lb/ft3 White

Flexible
3
FlexFoam-iT!™ VIII Pillow Soft 1:2 pbv 1,000 cps 35 sec. 25 min. 2 hrs. 194 8 times 8 lb/ft White
FlexFoam-iT!™ X 1:1 pbv 1,000 cps 50 sec. 45 min. 2 hrs. 157 6 times 10 lb/ft3 White
3
FlexFoam-iT!™ 14 1:2 pbv 1,000 cps 60 sec. 45 min. 2 hrs. 114 4 times 14 lb/ft White
FlexFoam-iT!™ 15 Tuff Stuff 1:2 pbv 1,000 cps 2 min 90 min 4 hrs 115 4 times 15 lb/ft3 White
3
FlexFoam-iT!™ 17 1:2 pbv 1,000 cps 60 sec. 30 min. 2 hrs. 93 3.5 times 17 lb/ft White
FlexFoam-iT!™ 23 FR 85:100 pbw 1,000 cps 90 sec. 60 min. 2 hrs. 68 2 times 23 lb/ft3 White
3
FlexFoam-iT!™ 25 1:2 pbw 1,000 cps 90 sec. 25 min. 2 hrs. 63 2 times 25 lb/ft White
EZ~Spray™ FlexFoam 1:1 pbv 1,000 cps 10 sec. 10 min. 15 min. 252 7 times 7 lb/ft3 White
Silicone Expanding Foams
Soma Foama™ 15 2:1 pbv 10,000 cps 30 sec. 20 min. 1 hr. 115 4 times 15 lb/ft3 White
3
Soma Foama™ 25 1:1 pbv 10,000 cps 90 sec. 20 min. 1 hr. 69 2-3 times 25 lb/ft White

60
61
TECHNICAL
CHARTS

r
8
-

si
si

o
38
3
95 i
95

ss
tio

ty
.)

ne
ate

ati
si
D6
D6
D6
D6 psi

Tim
ne

e
r

./lb

Lif
c
sile

d
M
M h-p
M

im
d

co
r

re
lo

xR
xe
l
e
m
m

. In e
n
TM
T
T

ard
l
u

u
ST

C
Ha

H
Mi
Mi
Vis d
Po

A:B
Sp
Vo ific
(C um
U
T
AS
Te
Elo sile
A nga
Co
Str pres
AS ngt ve
Co
Mo pres
AS ulus ve
Co

Product Name
EpoxAcast™ 650 101 Fast 100A:12B pbw 7,000 cps 20 min. 1.0 hr. 93B 18.22 6,000 psi 0.42% 16,350 psi 142,600 psi Off-White

EpoxAcast™ 650 102 Medium 100A:13B pbw 7,000 cps 90 min. 4.0 hrs. 93B 18.22 6,000 psi 0.42% 16,350 psi 142,600 psi Off-White

EpoxAcast™ 650 103 Slow 100A:14B pbw 7,000 cps 3.5 hrs. 24 hrs. 93B 18.22 6,000 psi 0.42% 16,350 psi 142,600 psi Off-White

EpoxAcast™ 650 HT High Temp 100A:10B pbw 5,000 cps 3.0 hrs. 24 hrs.* 93B 18.22 6,900 psi 0.82% 15,980 psi 134,400 psi Off-White
Casting Epoxies

EpoxAcast™ 650 BLACK 101 Fast 100A:12B pbw 7,000 cps 20 min. 1.0 hr. 93B 18.22 6,000 psi 0.42% 16,350 psi 142,600 psi Black

EpoxAcast™ 650 BLACK 102 Medium 100A:13B pbw 7,000 cps 90 min. 4.0 hrs. 93B 18.22 6,000 psi 0.42% 16,350 psi 142,600 psi Black

EpoxAcast™ 650 BLACK 103 Slow 100A:14B pbw 7,000 cps 3.5 hrs. 24 hrs. 93B 18.22 6,000 psi 0.42% 16,350 psi 142,600 psi Black

EpoxAcast™ 650 BLACK HT High Temp 100A:10B pbw 5,000 cps 3.0 hrs. 24 hrs.* 93B 18.22 6,900 psi 0.82% 15,980 psi 134,400 psi Black

EpoxAcast™ 655 101 Fast 100A:10B pbw 23,000 cps 30 min. 3.0 hrs. 90D 16.7 4,810 psi 0.54% 12,500 psi 125,500 psi Grey

EpoxAcast™ 655 102 Medium 100A:11B pbw 23,000 cps 75 min. 9.0 hrs. 90D 16.7 4,810 psi 0.54% 12,500 psi 125,500 psi Grey

EpoxAcast™ 655 103 Slow 100A:12B pbw 23,000 cps 3.5 hrs. 24 hrs. 90D 16.7 4,810 psi 0.54% 12,500 psi 125,500 psi Grey

EpoxAcast™ 655 HT HT High Temp 100A:8B pbw 12,000 cps 4.0 hrs. 24 hrs.* 90D 16.5 6,000 psi 0.50% 15,700 psi 270,000 psi Grey

EpoxAcast™ 670 HT HT High Temp 100A:16B pbw 6,000 cps 3.0 hrs. 24 hrs.* 90D 24.1 4,500 psi 0.65% 13,000 psi 101,400 psi Beige

EpoxAcast™ 690 N/A 100A:30B pbw 280 cps 5.0 hrs. 24 hrs. 80D 25.0 6,630 psi 1.8% 9,610 psi 91,300 psi Clear

EpoxAcast™ 692 N/A 100A:40B pbw 370 cps 12 hrs 72 hrs. 80D 25.7 4,585 psi 3.1% 5,777 psi 82,000 psi Clear

KEEP OUT OF REACH OF CHILDREN. WARNING: Known to the state of CA to * 24 Hours followed by Heat cure for 2 hrs at 175°F/80°C followed by 3 hrs at 300°F/150°C
cause cancer, birth defects or other reproductive harm. www.P65Warnings.co.gov B
Barcol 935 Hardness (ASTM D2240)
D
Shore D Hardness (ASTM D2240)
 )
40
n

o
22
.)

ty
e
tio

D-
/lb

ati
r

ga

osi
Lif
e
e
In.

r
s

c
TM ss
n

re
lo

xR
x
o

in
lu
ec

s
o

A:B
Mi
Mi
Vi ed
Po
Th
Wo Film
Tim king
Cu
Tim
Sh
Ha re D
(ASrdne
Sp
Vo ific
(Cu me
Ten
El ile
Co
Product Name
EpoxAmite™ 101 FAST 4:1 pbv 1,000 cps 11 min. 30 min. 6-8 hrs. 84D 24.5 2.45% Clear Yellow
EpoxAmite™ 102 MEDIUM 3:1 pbv 650 cps 22 min. 90 min. 10-15 hrs. 80D 25.0 3.15% Clear Yellow
EpoxAmite™ 103 SLOW 3:1 pbv 650 cps 55 min. 180 min. 20-24 hrs. 80D 25.2 2.63% Clear Yellow
EpoxAmite™ HT 100A:33B pbw 650 cps 60 min. 180 min. 24 hrs. 80D 25.2 2.3% Clear
EpoxAmite™ White 101 FAST 100A:20B pbw 3,400 cps 20 min. 45 min. 10-15 hrs. 83D 22.2 0.8% White
EpoxAmite™ White 102 MEDIUM 100A:23B pbw 2,800 cps 62 min. 120 min. 20-24 hrs. 85D 22.5 1.2% White
Red, Grey,
EpoxAcoat™ RED/GREY/WHITE/NEUTRAL 5:1 pbv Light Paste 20 min. 40 min. 16 hrs. 85D 19.4 N/A White or Neutral
EpoxAcoat™ HT 100A:188 pbw Light Paste 40 min. 75 min. 4 hrs.* 85D N/A N/A Dark Red
EPSILON™ + 101 Hardener 100A:20B pbw Variable 15 min. 45 min. 16 hrs. 75D 23.9 N/A Beige
EPSILON™ + 102 Hardener 100A:25B pbw Variable 30 min. 120 min. 24 hrs. 75D 24.3 N/A Beige
Epsilon™ PRO 2:1 pbv 4,000 cps 22 min. 35 min. 16 hrs. 65D 25.0 N/A Clear Amber
Habitat Cast N Coat™ 1:1 pbv 13,500 cps 85 min N/A 16 hrs. 85D 18.35 N/A Tan
Laminating/Coating Epoxies

Plasti-Paste™ EPOXY 2:1 pbv Paste 40 min. 60 min.** 16 hrs. 80D 27.73 N/A Off White
Tarbender™ 2:1 pbv 1100 cps 45 min. 2 hrs. 16 hrs. 75D 25.4 N/A Clear
XTC-3D™ 2:1 pbv* 350 cps 10 min.* 20 min. 2 hrs.* 80D 25.1 N/A Clear*
*See Technical Bulletin For More Information
**Recoat Time
) 0
8)

24

e
n

o
2
.)
64

*
ss

ty
D-
D-

ati
si
./lb

Tim

ife
r

R
M
e
t

co
TM

. In e

re
lo

tL

x
fl

o
a

lu
e
m

ix
s
ST
u

i
u

A:B
M
Mi
V ed
Po
C
Sh
Ha re D
(A rdne
Sp
Vo ific
(C m
He
De
Te ctio
(AS p
Co

Product Name
Free Form™ AIR 1:1 pbv Dough 30 - 120 min. 24 hrs. 50D 61.6 140°F/60°C Grey
Free Form™ AIR FAST 1:1 pbv Dough 6 - 10 min. 24 hrs. 60D 61.6 145°F/63°C Grey
Free Form™ AIR Fire Safe 1:1 pbv Dough 30 - 120 min. 24 hrs. 73D 34.6 140°F/60°C Grey
Free Form™ AIR HT 2:1 pbv Dough 150 min. 16 hrs. 55D 54.31 400°F/204°C Grey
160°F/74°C
Free Form™ Habitat™ Black 1:1 pbv Dough 60 min. 16 hrs. 85D 17.3 Black
212°F/100°C**
Epoxy Putties

160°F/74°C
Free Form™ Habitat™ Fire Safe™ 1:1 pbv Dough 90 min. 16 hrs. 85D 17.3 Neutral
212°F/100°C**
160°F/74°C
Free Form™ Habitat™ Flex FR 1:1 pbv Dough 90 min. 24 hrs. 45D 17.9 Light Brown
212°F/100°C**
Free Form™ SCULPT 1:1 pbv Putty 1.5 hrs. @ 1 lb. 24 hrs. 80D 20.73 N/A Grey
*Depnding on mass
**If post cured according to heat post curing schedule
KEEP OUT OF REACH OF CHILDREN. WARNING: Known to the state of CA to
cause cancer, birth defects or other reproductive harm. www.P65Warnings.co.gov 62
63
TECHNICAL
CHARTS

o
.)
th

e
)

/lb

ati
ra
gth

it
r

ng

Lif
e
s

In.
./ft 3y
e

m
.
xu
lo

lu
e
en l

t
ns
s
r

ix R
t r

M
Po
De
Tim old
Sp
Vo cific
(Cu me
De
(l
Ten
St ile
Fle
S
Co

Product Name
100 parts gypsum
+ 50 parts C-1 Latex 3,300 - 5,500 7,500 - 9,800 Bright
duoMatrix™-G 45 - 60 min.* 90 - 120 min.* 17.45 99
+ 10 parts C-2 Resin psi psi White
+ 0.5 Parts C-3 Hardner

100 parts A (powder) : 50

Drill Mixed: Drill Mixed: 3,300 - 5,500 7,500 - 9,800
duoMatrix™ NEO parts B (liquid) 17.45 99 White
30 min.* 90 min.* psi psi
by weight or volume

100 parts powder :

duoMatrix™ Systems

27 parts water by weight Drill Mixed: Drill Mixed: 3,300 - 5,500 7,500 - 9,800
Matrix Dryve™ 17.45 99 White
3parts powder : 1 part water 20 min.* 90 min.* psi psi
by volume
Pre-Mix Spray Up
Type I
100 parts 100 parts
Cement
Sand 80 parts 100 parts Up to
duoMatrix™-C 45 - 90 min. 16 hrs. N/A 100 - 130 Up to 900 psi White
5,000 psi
Matrix™-C 15 parts 15 parts
Water 23 parts 23 parts
A-R Glass 6 parts 10 parts

*Depending on mass and environmental temperature

 d
d
e

l
si

el

o
-p

.)
Yie
l Yi
h

e
)
e
t

/lb e
ate
ate

ati
l
r
g
r

Lif
e
u
u

si
s
m

In. olum
im
i

./ft 3

m
.
ci
x
x
lo

xR
n
m
en siv

t
t

l( bs sit y

Mi
Po
De
Tim old
De
Spe
(Cu fic V
Ten
Ten
U ile
Fle
Fle
Ul ral
Co
Str pres
Co

Product Name
Pre-Mix Spray Up
Pre-Mix Pre-Mix Pre-Mix Pre-Mix Pre-Mix Pre-Mix
Type I Cement 100 parts 100 parts 15.7
110 - 130 600 - 600 - 700 - 1,450 - 6,000 -
Sand 85 parts 100 parts - 13.3
Forton™ VF-774 900 psi 1,000 psi 1,200 psi 2,000 psi 9,000 psi
12 - 16
GFRC Additive VF-774 10-12 parts 12-14 parts Variable Variable
hrs.
(51% Solids) Water 24-27 parts 24-27 parts Spray-Up Spray-Up Spray-Up Spray-Up Spray-Up Spray-Up
14.4
Plasticizer 4-8 oz 4-8 oz 120 - 140 700 - 1,000 - 900 - 2,000 - 7,000 -
- 12.3
1,000 psi 1,600 psi 1,500 psi 3,500 psi 12,000 psi
A-R Glass 3% pbw 5% pbw

Forton™ VF-812 100 parts gypsum

FORTON™ Systems

Alpha Gypsum + 50 parts VF-812 Polymer 60 - 90 1,200 - 3,500 - 1,800 - 3,500 - 6,000 - Bright
20 - 30 min.* 95 - 100 17.45
Modifier + 10 parts MF-415 Resin min.* 1,400 psi 5,100 psi 2,900 psi 9,400 psi 9,000 psi White
(50% Solids) + 0.48 Parts Hardner

*Depending on mass and environmental temperature

KEEP OUT OF REACH OF CHILDREN. WARNING: Known to the state of CA to

cause cancer, birth defects or other reproductive harm. www.P65Warnings.co.gov
64
 65
TECHNICAL

°C

71
e

o
.)

24
e
/23
/lb

ati
CHARTS

D-
F
r

R
Lif
In.

3
.

re
lo

lu
ec

t
TM

ix
A:B
M
Po
AS
Cu
@ 7 Tim
Sp
Vo ific
(Cu me
Co
Product Name
3 parts water (70°F/21°C) : 2 parts powder by volume
Accu-Cast™ 370-SD™ 2 min. 3 min. 26.0 Off-White
4 parts water (70°F/21°C) : 1 part powder by weight
1 part water (80°F/27°C) : 1 part powder by volume Pink to
Accu-Cast™ BabyGel™ 2 2 min. 3 min. 26.0
4 parts water (80°F/27°C) : 1 part powder by weight Light Grey
Alginate

1 part water (80°F/27°C) : 1 part powder by volume

Accu-Cast™ BodyGel™ 880 5 min. 8 min. 26.0 Off-White
3 parts water (80° F/27° C) : 1 part powder by weight
3 parts water (90°F/32°C) : 2 parts powder by volume
Accu-Cast™ FaceGel™ 590 3.5 min. 5 min. 26.0 Tan
4 parts water (90°F/32°C) : 1 partpowder by weight

3 part water (70°F/21°C) : 2 parts powder by volume

Accu-Cast™ HandGel™ 570 3.5 min. 5 min. 26.0 Off-White
4 parts water (70°F/21°C) : 1 part powder by weight

1 part water (70°F/21°C) : 1.5 parts powder by volume White to Pink

Accu-Cast™ Phase 2™ Gel 1.5 min. 2.5 min.
2.5 parts water (70°F/21°C) : 1 part powder by weight to White

Alja-Safe™ 1 part water (80°F/27°C) : 1 part Alja-Safe™ powder by volume 5 min. 8 min. 26.0 Light Purple

Alja-Safe™ Acrobat 1 part water (80°F/27°C) : 1 part Acrobat powder by volume 5 min. 8 min. 26.0 Off-White

Alja-Safe™ Breeze 5 parts water (80°F/27°C) : 1 part liquid by volume 3 min. 8 min. 26.0 Blue

it

Kit
rK G

er Set
e

t
t
c
m
o
u

n
r
r
rt
r
i
im
im

u
™
™

dy
m

rto

Bo
Do
Sta ble™
Sta dard
Fo
Sta n™ M
Lif
Sta astin
Kit er
Po
Sta rable
Kit ter
Ult
Blo ate
Kit d ™
Ult
Wo ate
Kit nd
Ult
Zo ate
Kit bie

Find Complete Technical Bulletins & Material

• Body Double™ • 7 lbs VF-812 • Alja-Safe™ • How-To Booklet • Ultimate Blood™ Base • Step-By-Step • Step-By-Step
Silicone Molding Gel How-To Guide How-To Guide

Safety Data Sheets (SDS) at: www.smooth-on.com

• 1 lbs MF-415 • OOMOO™ 30 • Ultimate Blood™ Thinner
• 2 Rolls of • 10 lbs FGR-95 • Casting Plaster Molding Rubber • Ultimate Blood™ Thixo • Skin Tite™ Silicone • Thi-Vex™
4” Width Bandages • • Smooth-Cast™ 300 • Thi-Vex™ Thickening Agent
• 22 grams Hardener Quick Start Guide • Ultimate Blood™ Blue Tint Thickening Agent
• Body Double™ Casting Resin • Skin Tite™ Silicone
Release Cream • 1 lb Chopped • Ultimate Blood™ Red Tint • Silc Pig™ Pigment
• SuperSeal™ • Silc Pig™ Pigment
Starter Kits

E-Glass • Ultimate Blood™ Yellow Tint

• Mixing Sticks & Sealing Agent • Rubber Glass™ • Makeup Pallette
Containers • Ease Release™ 205 • Mixing Sticks & Cups Cured Disks
• Rubber Glass™
Release Agent • Mixing Sticks & Cups Cured Disks
• Quick Start Guide • Zombie Teeth
• Mixing Sticks & Cups
Seminars & Master Class Series
Introduction to
Mold Making, Casting,
Materials and More

Thousands of people from all over the world

have attended Smooth-On’s two day training seminars.
seminars .
Introduction to Mold Making, Limited Class Sizes for More Than Just
Casting and More Maximum Learning Experience Mold Making and Casting
Slides, videos and hands-on You are never without someone We will show you a world
demonstration introduce you to guide you. Whether you are a of material possibilities and
to the basics of mold making beginner or seasoned user of how these materials can be
and casting, in an easy-to- these materials, you will be used for hundreds of
understand format. Attendees inspired and understand why applications you never
make their own molds and many seminar graduates thought were possible.
castings over the 2-day period. describe our classes as a
”life changing experience“.

Presentations / Demonstrations
1- DAY MASTER CLASSES
Smooth-On’s ‘Master Class Series’ showcases artists that are
known by the art community and who are willing to share their
accumulated knowledge, skills and experience with others. Learn
from their unique perspectives in the spirit of exchanging ideas
and information related to their craft.

Black Widow
Sculpture
Tom Kuebler Adam Nelson Bill Doran by Tom Kuebler

Past Master Class artists include Tom Kuebler, Adam Nelson and Bill Doran. Check our schedule online for more information.
WATCH
LEARN On You

DO
Phoner

WATCH VIDEO LIBRARY

LEARN On Your
Tablet
SMOOTH-ON.COM/TUTORIALS
• AQUARIUMS & ZOOS

DO
• ARCHITECTURAL RESTORATION
• BUDDY
B
 UDDY RHODES™
CONCRETE PRODUCTS
•  CANDLE MAKING
• CONCRETE
C
 ONCRETE MOLD MAKING
AND CASTING
• COSPLAY
• ENCAPSULATION & DISPLAY
• FOOD SAFE MOLD MAKING
• HOME CRAFTS & HOBBIES
• INDUSTRIAL
On Your • LARGE SCALE APPLICATIONS
Computer • LIFE CASTING
• MAKEUP FX
• MEDICAL SIMULATION
• MOLD MAKING
• ORTHOTICS & PROSTHETICS
• PROP MAKING
youtube.com/smoothoninc • PROTOTYPING / INVENTING
facebook.com/smoothon
• SCULPTURE & ART CASTING
• SPECIAL EFFECTS
twitter.com/smoothon • SPRAYABLE MATERIALS
• TAXIDERMY
instagram.com/smoothon • THEMED ENVIRONMENTS
• VACUUM BAGGING
tiktok.com/@smoothon • WOODWORKING
• WOUND SIMULATIONS
5600 Lower Macungie Road, Macungie PA 18062 | Tel: 610.252.5800 | Fax: 610.252.6200 | www.smooth-on.com
7149-11200-0822