om PRELIMINARY

.c
4U
et
he
aS
at : General
TO
.DDATE : Sep. 13, 2002
w
w
w
SAMSUNG
SAMSUNGTFT-LCD
MODEL
TFT-LCD
om
MODEL NO.
NO. :: LTN154X1-L02
.c
LTN154X1-L02

4U
et
he
NOTE :

a S
at
.D
w
The information described in this SPEC is preliminary and can be changed without prior notice.

w
w m
o
APPROVED BY : .c
4U
PREPARED BY : Application Engineering 1 Group e t
h e
aS
SAMSUNG ELECTRONICS CO., LTD.
at
.D
w
Doc.No. LTN154X1-L02 Rev.No w
04-P00-G-020725 Page 1 / 24
w
 CONTENTS PRELIMINARY

Record Of Revision -------------------( 3 )

General Description -------------------( 4 )

1. Absolute Maximum Ratings -------------------( 5 )

1.1 Absolute Ratings of Environment
1.2 Electrical Absolute Maximum Ratings

2. Optical Characteristics -------------------( 7 )

3. Electrical Characteristics - - - - - - - - - - - - - - - - - - - ( 11 )
3.1 TFT LCD Module
3.2 Back Light Unit

4. Block Diagram - - - - - - - - - - - - - - - - - - - ( 14 )
4.1 TFT LCD Module
4.2 Back Light Unit

5. Input Terminal Pin Assignment - - - - - - - - - - - - - - - - - - - ( 15 )

5.1 Input Signal & Power
5.2 LVDS Interface:Transmitter
5.3 Back Light Unit
5.4 Timing Diagrams of LVDS for Transmission
5.5 Input Signals, Basic Display Colors and Gray Scale of Each Color.
5.6 Pixel Format

6. Interface Timing - - - - - - - - - - - - - - - - - - - ( 20 )
6.1 Timing Parameters(DE MODE)
6.2 Timing Diagrams of interface Signal (DE MODE)
6.3 Power ON/OFF Sequence

7. Outline Dimension - - - - - - - - - - - - - - - - - - - ( 22 )

8. General Precaution - - - - - - - - - - - - - - - - - - - ( 23 )

Doc.No. LTN154X1-L02 Rev.No 04-P00-G-020725 Page 2 / 24

 REVISION
REVISIONHISTORY
HISTORY PRELIMINARY

Date Rev.No. Page Summary

Jul.25.2002. P00 ALL LTN154X1-L02model was first issued

Doc.No. LTN154X1-L02 Rev.No 04-P00-G-020725 Page 3 / 24

 GENERAL DESCRIPTION PRELIMINARY

DESCRIPTION
LTN154X1 is a color active matrix TFT (Thin Film Transistor) liquid crystal display (LCD)
that uses amorphous silicon TFT as a switching devices. This model is composed of a TFT
LCD panel, a driver circuit, a back-light system. The resolution of a 15.4 ″ contains
1280 x 800 pixels and can display up to 262,144colors. 6 o'clock direction
is the optimum viewing angle.

FEATURES
• Thin and light weight
• High contrast ratio, high aperture structure
• Super Wide Viewing Angle
• Fast Response Time
• Wide XGA (1280x800 pixels) resolution
• Low power consumption
• Single CCFL
• DE(Data enable) only mode
• 3.3V LVDS Interface
• Onboard EEDID chip

APPLICATIONS
• Notebook PC and desktop monitors
• Display terminals for AV application products
• Monitors for Industrial machine
• If the usage of this product is not for PC application, but for others, please contact SEC

GENERAL INFORMATION

ITEM SPECIFICATION UNIT NOTE

Display area 331.2max(H) x 207.0max(V) (15.4″ diagonal ) mm

Driver element a-Si TFT active matrix

Display colors 262,144

Number of pixel 1280 X RGB(3) X 800 pixels

Pixel arrangement RGB vertical stripe

Pixel pitch 0.25875(H) x 0.25875 (V) mm

Display Mode Normally white

Surface treatment HAZE (25), HARD-COATING (3H)

Doc.No. LTN154X1-L02 Rev.No 04-P00-G-020725 Page 4 / 24

 PRELIMINARY
Mechanical Information

ITEM MIN. TYP. MAX. NOTE

Horizontal (H) 343.5 344.0 344.5

Module Vertical (V) 221.5 222.0 222.5 LCD module only
size
Thickness (T) - - 6.5

Weight (g) - - 610 PMMA

1. ABSOLUTE MAXIMUM RATINGS

1.1 ENVIRONMENTAL ABSOLUTE RATINGS

ITEM SYMBOL MIN. MAX. UNIT NOTE

Storage temperature TSTG -25 65 °C (1)

Operating temperature (1)

(Temperature of glass surface) TOPR 0 50 °C

Shock ( Non-operating ) Snop - 220 G (2),(4)

Vibration (Non-operating) Vnop - 1. 5 G (3),(4)

Note (1) Temperature and relative humidity range are shown in the figure below.
90 % RH Max. ( 40°C ≥ Ta)
Maximum wet - bulb temperature at 39°C or less. (Ta > 40°C) No condensation.
Relative Humidity ( %RH)
100
90

80

60
Operating Range
40

20

5
Storage Range
0
-40 -20 0 20 40 60 80

Temperature (OC)

(2) 220G, 2ms, Half sine wave, one time for ±X, ±Y, ±Z axis
(3) 10 ~ 300 ~ 10 Hz, Sweep rate 10min, 30min for X, Y,Z axis
(4) At testing Vibration and Shock, the fixture in holding the Module to be tested have to be
hard and rigid enough so that the Module would not be twisted or bent by the fixture.

Doc.No. LTN154X1-L02 Rev.No 04-P00-G-020725 Page 5 / 24

 PRELIMINARY
1.2 ELECTRICAL ABSOLUTE RATINGS

(1) TFT LCD MODULE VDD =3.3, Vss=GND= 0V

ITEM SYMBOL MIN. MAX. UNIT NOTE

Power Supply Voltage VDD Vss -0.3 3.8 V (1)

Logic Input Voltage VIN Vss -0.3 VDD+0.3 V (1)

NOTE (1) Within Ta = 25 ± 2 °C

(2) BACK-LIGHT UNIT

Ta = 25 ± 2 °C

ITEM SYMBOL MIN. MAX. UNIT. NOTE

Lamp current IL 2.0 7.0 mArms (1)

Lamp frequency FL 50 80 KHz (1)

NOTE (1) Permanent damage to the device may occur if maximum values are exceeded.
Functional operation should be restricted to the conditions described under Normal Operating
Conditions.

Doc.No. LTN154X1-L02 Rev.No 04-P00-G-020725 Page 6 / 24

2. OPTICAL CHARACTERISTICS PRELIMINARY
The following items are measured under stable conditions. The optical characteristics
should be measured in a dark room or equivalent state with the methods shown in Note (7).
Measuring equipment : TOPCON BM-5A
* Ta = 25 ± 2°C , VDD=3.3V, fv= 60Hz, fDCLK=68.9MHz, IL = 6.0mA

ITEM SYMBOL CONDITION MIN. TYP. MAX. UNIT NOTE

Contrast Ratio - 300 -

CR (1), (2), (7)
(5 Points)
φ = 0,
Response Rising TR - 10 15
msec (1), (3)
Time at Ta θ = 0
Falling TF - 15 20

Average Luminance 170 185 (4)

YL,AVE - cd/m2
of White (5 Points) at 6.0mA

RX (0.550) (0.580) (0.610)

Red
RY (0.310) (0.340) (0.370)

GX (0.280) (0.310) (0.340)

Green
Color
GY (0.520) (0.550) (0.580)
Chromaticity PR650
( CIE ) BX (0.125) (0.155) (0.185)
Blue
BY (0.125) (0.155) (0.185)
WX 0.283 0.313 0.343
White
WY
0.299 0.329 0.359

θR - 65 -
Hor.
θL CR( at - 65 -
Viewing center point) Degrees (1)
Angle φH ≥ 10 - 50 -
Ver.
φL - 50 -

13 Points
δL - - 1.8 (5),(6),(7)
White Variation

Doc.No. LTN154X1-L02 Rev.No 04-P00-G-020725 Page 7 / 24

 PRELIMINARY
Note 1) Definition of Viewing Angle :
Normal Line
φ = 0o, θ = 0o

θL
θR
φL φH 12 O’clock
θ L =90o x y direction
φ H = 90o

6 O’ clock y’ x’
direction
θR =90o
φ L= 90o

Luminance of all pixel white

Note 2) Definition of Contrast Ratio (CR) =
Luminance of all pixel dark

CR1 + CR2 + CR3 + CR4 + CR5

CR =
5

POINTS : 1 , 22 , 3 , 4 , 5 at FIGURE OF NOTE 6)

Note 3) Definition of Response time :

Display data White(TFT OFF) Black(TFT ON) White(TFT OFF)

TR TF
100%
Optical
90%
Response

10%
0%
Time

Doc.No. LTN154X1-L02 Rev.No 04-P00-G-020725 Page 8 / 24

 PRELIMINARY

Note 4) Definition of Average Luminance of White : measure the luminance of white at 5 points.

320 640 960

Average Luminance of White ( Y L,AVE )

1 2 200
YL1 + YL2 + YL3 + YL4 + YL5
Y L,AVE =
5 400
5

3 4 600

Note 5) The luminance uniformity of 13 points is defined by dividing the maximum luminance values
by the minimum test point luminance

13 Points Max Luminance (13 pts, 1~13)

Luminance Uniformity =
Min Luminance (13 pts, 1~13)

Note 6) Luminance uniformity measurement performed at the 13 points and 5 points as defined
in the drawing below.

320 640 960

VIEW AREA
6 7 8
10mm
1 2 200

9 5 10 400 : test point

3 4 600
10mm
11 12 13

10mm 10mm

Doc.No. LTN154X1-L02 Rev.No 04-P00-G-020725 Page 9 / 24

 PRELIMINARY

Note 7) After stabilizing and leaving the panel alone at a given temperature for 30 minutes, the measurement
should be executed. Measurement should be executed in a stable, windless,and dark room.
30 minutes after lighting the back-light. This should be measured in the center of screen.
Lamp current : 6.0 mA
Environment condition : Ta = 25 ± 2 °C

Photodetector
( TOPCON BM-5A)

o
Field = 2
40 cm

TFT-LCD module LCD panel

Center of the screen

Optical characteristics measurement setup

Doc.No. LTN154X1-L02 Rev.No 04-P00-G-020725 Page 10 / 24

3. ELECTRICAL CHARACTERISTICS PRELIMINARY
3.1 TFT LCD MODULE
Ta = 25 ± 2°C

ITEM SYMBOL MIN TYP MAX UNIT NOTE

Voltage of Power Supply VDD 3.0 3.3 3.6 V

Differential Input High VIH - - +100 mV

Voltage for LVDS (1)
Receiver Threshold Low VIL -100 - - mV

Vsync Frequency fv - 60 - Hz

Hsync Frequency fH - 48.96 - KHz

Main Frequency fDCLK - 68.9 - MHz

Rush Current IRUSH - - (1.5) A (4)

White - TBD - mA (2),(3)*a

Electric Circuit
Power Mosaic IDD - TBD - mA (2),(3)*b
Consumption Maximum
- TBD TBD mA (2),(3)*c
Pattern

Note (1) Condition : VCM=+1.2V(Common mode Voltage)

(2) fV=60Hz, fDCLK = 68.9 MHz, Vdd = 3.3V , DC Current.
(3) Power dissipation check pattern

*a) White Pattern *b)Mosaic Pattern

VIEW AREA

Display Brightest Gray Level

Display Darkest Gray Level

Doc.No. LTN154X1-L02 Rev.No 04-P00-G-020725 Page 11 / 24

 PRELIMINARY
*c) Maximum Power pattern : 1dot inversion

(4) Rush current measurement condition

3.3V M1
2SK1059
VDD ( LCD INPUT)
FUSE
R1 C1
47K 1uF

R2
CONTROL SIGNAL M2
(HIGH to LOW) 2SK1399
1K

12V
R3 C2

C3 47K
10000pF
1uF

VDD rising time is 470us

3.3V
0.9VDD

0.1VDD
GND
470us

Doc.No. LTN154X1-L02 Rev.No 04-P00-G-020725 Page 12 / 24

 3.2 BACK-LIGHT UNIT
PRELIMINARY
The backlight system is an edge - lighting type with a single CCFT ( Cold Cathode Fluorescent Tube ).
The characteristics of a single lamp are shown in the following tables.

INVERTER : SIC 130T(SEMCO, fL=60KHz)

Ta = 25 ± 2°C

ITEM SYMB MIN TYP MAX UNIT NOTE

Lamp Current IL (3.0) - (6.0) mArms (1)

Lamp Voltage VL - TBD - Vrms IL=6.0mA

Frequency fL (50) (60) (65) KHz (2)

(3)
Power Consumption PL - TBD - W
IL=6.0mA
Operating Life Time Hr 10000 - - Hr (4)

- - TBD Vrms 25°C

Startup Voltage VS
- - TBD Vrms 0°C

Lamp Startup Time VS - - 0.5 sec (5)

Note) The waveform of the inverter output voltage must be area symmetric and the design of the
inverter must have specifications for the modularized lamp.
The performance of the back-light, for example life time or brightness, is much influenced by the
characteristics of the DC-AC inverter for the lamp. So all the parameters of an inverter should be carefully
designed so as not to produce too much leakage current from high-voltage output of the inverter.
When you design or order the inverter, please make sure that a poor lighting caused by the mismatch of
the back-light and the inverter(miss lighting, flicker, etc.) never occur. When you confirm it, the module
should be operated in the same condition as it is installed in your instrument.

Note (1) Lamp current is measured with a high frequency current meter as shown below.

HOT : Pink
1
LCD COLD : WHITE INVERTER
MODULE 2 A SIC 130T
No 2 Pin is VLOW .

(2) Lamp frequency may produce interference with horizontal synchronous frequency and this
may cause line flow on the display. Therefore lamp frequency should be detached from the
horizontal synchronous frequency and its harmonics as far as possible in order to avoid interference.

(3) refer to IL X VL to calculate.

(4) Life time (Hr) of a lamp can be defined as the time in which it continues to operate under the
condition Ta = 25 ± 2°C and IL = 6.0 mArms until one of the following event occurs.
1. When the brightness becomes 50% or lower than it’s original.
2. When the Effective ignition length becomes 80% or lower than it’s original value.
(Effective ignition length is defined as an area that has less than 70% brightness compared to
the brightness in the center point.)

(5) The voltage above this value should be applied to the lamp for more than 1 second to startup
Otherwise the lamp may not be turned on.

Doc.No. LTN154X1-L02 Rev.No 04-P00-G-020725 Page 13 / 24

 PRELIMINARY
4. BLOCK DIAGRAM

4.1 TFT LCD Module

LVDS RSDS
User- LVDS Receiver &
Connector Timing Controller
Source
Driver
ICs 15.4”WXGA
TFT-LCD Panel

DC-DC Gamma
Converter Generator

VCOM
Video Signal Generator
Control Signal
VCOM
Gamma
DVDD SOURCE PCB
AVDD Gate Driver ICs
Von/Voff

4.2 BACKLIGHT UNIT

Reflector

1 HOT (PINK)
LAMP

2 COLD(WHITE)

Note) The output of the inverter may change according to the material of the reflector.

Doc.No. LTN154X1-L02 Rev.No 04-P00-G-020725 Page 14 / 24

5. INPUT TERMINAL PIN ASSIGNMENT
PRELIMINARY
5.1. Input Display Signal & Power (Input Connector : JAE, FI-XB30SL-HF10)

PIN# SYMBOL FUNCTION POLARITY REMARK

1 VSS Ground
2 VDD Power Supply, 3.3 V (typical )
3 VDD Power Supply, 3.3 V (typical)
4 V EEDID DDC 3.3V power
5 NC No connect
6 Clk EEDID DDC Clock
7 DATA EEDID DDC Data
8 RxIN0- LVDS differential data input Negative R0-R5, G0
9 RxIN0+ LVDS differential data input Positive
10 VSS Ground
11 RxIN1- LVDS differential data input Negative G1-G5,
12 RxIN1+ LVDS differential data input Positive B0-B1

13 VSS Ground
14 RxIN2- LVDS differential data input Negative B2-B5,
15 RxIN2+ LVDS differential data input Positive HS,VS,DE

16 VSS Ground
17 ClkIN- LVDS differential clock input Negative
18 ClkIN+ LVDS differential clock input Positive
19 VSS Ground
20 NC No connect
21 NC No connect
22 NC No connect
23 NC No connect
24 NC No connect
25 NC No connect
26 NC No connect
27 NC No connect
28 NC No connect
29 NC No connect
30 NC No connect

Doc.No. LTN154X1-L02 Rev.No 04-P00-G-020725 Page 15 / 24

 PRELIMINARY
5.2 LVDS Interface

Transmitter SN75LVDS86 or Compatible

Pin No. Name RGB Signal Pin No. Name RGB Signal

44 TxIN0 R0 12 TxIN11 G5

45 TxIN1 R1 13 TxIN12 B0

47 TxIN2 R2 15 TxIN13 B1

48 TxIN3 R3 16 TxIN14 B2

1 TxIN4 R4 18 TxIN15 B3

3 TxIN5 R5 19 TxIN16 B4

4 TxIN6 G0 20 TxIN17 B5

6 TxIN7 G1 22 TxIN18 Hsync

7 TxIN8 G2 23 TxIN19 Vsync

9 TxIN9 G3 25 TxIN20 DE

10 TxIN10 G4 26 TxCLK IN Clock

Graphics controller SN75LVDS86 or LXD01813

18-bit RED0 Compatible (LVDS+I/F IC)
TxIN0 -
RED1 TxIN1 TxOUT0- 8 RxIN0-
RED2 TxIN2 100Ω
RED3 TxIN3 - RxIN0+
TxOUT0+ 9
RED4 TxIN4
RED5 TxIN5 -
GREEN0 TxIN6 TxOUT1- 11 RxIN1-
GREEN1 TxIN7 100Ω
GREEN2 TxIN8 TxOUT1+ - RxIN1+
12
GREEN3 TxIN9
GREEN4 TxIN10
TxIN11 -
GREEN5 TxOUT2- 14 RxIN2-
BLUE0 TxIN12 100Ω
BLUE1 TxIN13
TxOUT2+
- RxIN2+
BLUE2 TxIN14 15
BLUE3 TxIN15
BLUE4 TxIN16 TxCLKOUT- - RxCLKIN-
17
BLUE5 TxIN17
Hsync TxIN18 100Ω RxCLKIN+
Vsync TxIN19 TxCLKOUT+ -
18
Enable TxIN20
CLOCK TxClkIN

Doc.No. LTN154X1-L02 Rev.No 04-P00-G-020725 Page 16 / 24

 PRELIMINARY
5.3 BACK LIGHT UNIT

Connector : JST BHSR - 02VS -1

Mating Connector : JST SM02B-BHSS-1

Pin NO. Symbol Color Function

1 HOT PINK High Voltage

2 COLD WHITE Low Voltage

5.4 Timing Diagrams of LVDS For Transmission

T
TxCLK OUT
RxCLK IN

T/7

Rx IN2 RxOUT20 RxOUT19 RxOUT18 RxOUT17 RxOUT16 RxOUT15 RxOUT14

DE Vsync Hsync B5 B4 B3 B2

Rx IN1 RxOUT13 RxOUT12 RxOUT11 RxOUT10 RxOUT9 RxOUT8 RxOUT7

B1 B0 G5 G4 G3 G2 G1

RxIN0 RxOUT6 RxOUT5 RxOUT4 RxOUT3 RxOUT2 RxOUT1 RxOUT0

G0 R5 R4 R3 R2 R1 R0

Doc.No. LTN154X1-L02 Rev.No 04-P00-G-020725 Page 17 / 24

 PRELIMINARY
5.5 Input Signal,Basic Display Colors and Gray Scale of Each Colors

DA TA S IGNA L G RA Y
CO LOR DISP LAY RE D G RE E N BLUE S CA LE
LEVEL
R0 R1 R2 R3 R4 R5 G 0 G 1 G 2 G 3 G 4 G 5 B 0 B 1 B 2 B 3 B 4 B 5
B L ACK 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 -
B L UE 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 -
GREEN 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 -
B A S IC CYAN 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 -
CO LOR RE D 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 -
MAGENTA 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 -
Y E LLOW 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 -
W HITE 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -
B L ACK 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R0

DA RK 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R1

G RA Y ↑ 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R2
S CA LE : : : : : : : : : : : : : : : : : :
R3 ~R6 0
OF : : : : : : : : : : : : : : : : : :
RE D ↓ 1 0 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 R6 1
L IGHT 0 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 R6 2
RE D 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 R6 3
B L ACK 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 G0

DA RK 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 G1

G RA Y ↑ 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 G2
S CA LE : : : : : : : : : : : : : : : : : :
G 3 ~G 60
OF : : : : : : : : : : : : : : : : : :
G RE E N ↓ 0 0 0 0 0 0 1 0 1 1 1 1 0 0 0 0 0 0 G61
L IGHT
0 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 G62
G RE E N 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 G63
B L ACK 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 B0
0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 B1
DA RK
G RA Y ↑ 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 B2
S CA LE : : : : : : : : : : : : : : : : : :
B 3 ~B 60
OF : : : : : : : : : : : : : : : : : :
B L UE ↓ 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 1 1 1 B61
L IGHT
0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 B62
B L UE 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 B63

Note
(1) Definition of Gray : Rn : Red Gray, Gn : Green Gray, Bn : Blue Gray (n = Gray level)
(2) Input Signal : 0 = Low level voltage, 1 = High level voltage

Doc.No. LTN154X1-L02 Rev.No 04-P00-G-020725 Page 18 / 24

 5.6 PIXEL FORMAT
PRELIMINARY

Pixel 1 Pixel 1280

Line 1 R G B R G B R G B R G B

LTN154X1-L02

Line 800 R G B R G B R G B R G B

Doc.No. LTN154X1-L02 Rev.No 04-P00-G-020725 Page 19 / 24

 PRELIMINARY
6. INTERFACE TIMING
6.1 Timing Parameters

Signal Item Symbol Min Typ Max Unit

Frame Frequency Cycle TV (804) 816 (900) lines

Vertical Active Display

TVD - 800 - lines
Display Term Period
One Line
Cycle TH (1368) 1408 (1800) clocks
Scanning Time
Horizontal Active Display
THD - 1280 - clocks
Display Term Period

6.2 Timing diagrams of interface signal

TV

TVD

DE

TH

DCLK
TC
THD

DE

DATA Valid display data ( 1280 pixel)

SIGNALS

Doc.No. LTN154X1-L02 Rev.No 04-P00-G-020725 Page 20 / 24

 6.3 Power ON/OFF Sequence
PRELIMINARY
: To prevent a latch-up or DC operation of the LCD module, the power on/off sequence
should be as the diagram below.

Power Supply 0.9 VDD 0.9 VDD

VDD 0.1 VDD
0.1 VDD
0V

0 < T1 ≤ 10 msec T1
0 < T2 ≤ 50 msec T3
0 < T3 ≤ 50 msec T2 T4
400ms ≤ T4
Signals VALID
0V

Power On Power Off

Back-light
200 msec ≤ T5 50% 50%
200 msec < T6

T5 T6

Power ON/OFF Sequence

T1 : Vdd rising time from 10% to 90%

T2 : The time from Vdd to valid data at power ON.
T3 : The time from valid data off to Vdd off at power Off.
T4 : Vdd off time for Windows restart
T5 : The time from valid data to B/L enable at power ON.
T6 : The time from valid data off to B/L disable at power Off.

NOTE.
(1) The supply voltage of the external system for the module input should be the same
as the definition of VDD.
(2) Apply the lamp voltage within the LCD operation range. When the back-light turns on
before the LCD operation or the LCD turns off before the back-light turns off, the
display may momentarily become white.
(3) In case of VDD = off level, please keep the level of input signals on the low or keep
a high impedance.
(4) T4 should be measured after the module has been fully discharged between power
off and on period.
(5) Interface signal shall not be kept at high impedance when the power is on.

Doc.No. LTN154X1-L02 Rev.No 04-P00-G-020725 Page 21 / 24

 8. GENERAL PRECAUTIONS PRELIMINARY

1. Handling

(a) When the module is assembled, It should be attached to the system firmly
using every mounting holes. Be careful not to twist and bend the modules.

(b) Refrain from strong mechanical shock and / or any force to the module. In addition to
damage, this may cause improper operation or damage to the module and CCFT back-light.

(c) Note that polarizers are very fragile and could be easily damaged. Do not press or scratch
the surface harder than a HB pencil lead.

(d) Wipe off water droplets or oil immediately. If you leave the droplets for a long time,
Staining and discoloration may occur.

(e) If the surface of the polarizer is dirty, clean it using some absorbent cotton or soft cloth.

(f) The desirable cleaners are water, IPA(Isoprophyl Alcohol) or Hexane.

Do not use Ketone type materials(ex. Acetone), Ethyl alcohol, Toluene, Ethyl acid or Methyl
chloride. It might permanent damage to the polarizer due to chemical reaction.

(g) If the liquid crystal material leaks from the panel, it should be kept away from the eyes or
mouth . In case of contact with hands, legs or clothes, it must be washed away thoroughly
with soap.

(h) Protect the module from static , it may cause damage to the C-MOS Gate Array IC.

(i) Use fingerstalls with soft gloves in order to keep display clean during the incoming
inspection and assembly process.

(j) Do not disassemble the module.

(k) Do not pull or fold the lamp wire.

(l) Do not adjust the variable resistor which is located on the back side.

(m) Protection film for polarizer on the module shall be slowly peeled off just before use so
that the electrostatic charge can be minimized.

(n) Pins of I/F connector shall not be touched directly with bare hands.

Doc.No. LTN154X1-L02 Rev.No 04-P00-G-020725 Page 23 / 24

2. STORAGE
PRELIMINARY

(a) Do not leave the module in high temperature, and high humidity for a long time.
It is highly recommended to store the module with temperature from 0 to 35 °C and
relative humidity of less than 70%.

(b) Do not store the TFT-LCD module in direct sunlight.

(c) The module shall be stored in a dark place. It is prohibited to apply sunlight or fluorescent
light during the store.

3. OPERATION

(a) Do not connect,disconnect the module in the “ Power On” condition.

(b) Power supply should always be turned on/off by following item 6.3
“ Power on/off sequence “.

(c) Module has high frequency circuits. Sufficient suppression to the electromagnetic
interference shall be done by system manufacturers. Grounding and shielding methods
may be important to minimize the interference.

(d) The cable between the back-light connector and its inverter power supply shall be a
minimized length and be connected directly . The longer cable between the back-light
and the inverter may cause lower luminance of lamp(CCFT) and may require higher
startup voltage(Vs).

4. OTHERS

(a) Ultra-violet ray filter is necessary for outdoor operation.

(b) Avoid condensation of water. It may result in improper operation or disconnection

of electrode.

(c) Do not exceed the absolute maximum rating value. ( the supply voltage variation, input
voltage variation, variation in part contents and environmental temperature, so on)
Otherwise the module may be damaged.

(d) If the module displays the same pattern continuously for a long period of time,it can be
the situation when the image “sticks” to the screen.

(e) This module has its circuitry PCB’s on the rear side and should be handled carefully in
order not to be stressed.

Doc.No. LTN154X1-L02 Rev.No 04-P00-G-020725 Page 24 / 24