12/5/2016 Generator Protection Explained

30th March 2014 Generator Protection Explained

Generator Protection

[http://2.bp.blogspot.com/­
OXWt9oM9kJ8/UcaiuCjHp4I/AAAAAAAACaA/HlKpsSPD1zw/s1600/8.jpg]
GENERATOR AND ITS PROTECTION

The core of an electrical power system is the generator. There are power units based on steam, gas, naphtha,
water power, diesel engine drive and wind mills. The range of size extends from a few hundred KVA (or even less) for
engine­driven and hydro sets up to turbine driven sets exceeding 500MVA in rating.

Small and medium sized sets may be directly connected to the distribution system. A larger unit is usually
associated with an individual transformer, transmission system. No switchgear is provided between the generator
and transformer may be tapped off the interconnection for the supply of power to auxiliary plant. Provision of a
breaker in between Generator and Transformer makes it possible to draw power for the auxiliaries through the UAT
from the EHV bus, even when machine is not in service. Typical arrangements are given in figure............

Protection of 6.6 KV system in generating stations:

Major Thermal Stations auxiliaries are fed from 6.6 KV bus which is connected by a 220/6.6KV Station
Transformers and Generation voltage/6.6 KV Unit Auxiliary Transformers.

Station Transformers:
The vector group of these transformers is Star­Delta i.e. the 6.6 KV system is delta connected Or The vector
group of these transformers is Star­Star with the 6.6KV side grounded through a high resistance.
Unit Auxilary Transformers :
The vector group of these transformers is Delta – Star (ungrounded Star on 6.6KV System).Any earth fault on
the 6.6 KV system cannot be seen by any E/L relay (since the 6.6 KV system is delta connected or high resistance
grounded or ungrounded Star).However 3­O/L relays are provided on the 6.6KV side of the Station Transformers and
http://powerplantpro.blogspot.in/2014/03/generator­protection­explained.html 1/9
12/5/2016 Generator Protection Explained

Unit Auxilary Transformers . An open­delta voltage of the 6.6 KV bus PT is connected to an over voltage relay with a
very low setting. Any earth fault on the 6.6 KV system will cause the presence of open­delta voltage and make the
voltage relay operate which is connected to give alarm. The faulty 6.6 KV feeder can be identified by tripping the 6.6
KV outlets one after the other.

Generator Protection – Various Functions

Generating units are the source of the power system and their security against any adverse conditions is
most important in the system. The generator protection must ensure a fast and selective detection of any fault in
order to minimize their dangerous effects.

Protection of passive elements like transmission lines and transformers is relatively simple which involves
isolation of faulty element from the system, whereas protection of generators involves tripping of generator field
breaker, generator breaker and turbine.
Generator Protections are broadly classified into three types.

CLASS – A :­ This covers all electrical protections for faults within the generating unit in which generator field breaker,
generator breaker and turbine should be tripped.

CLASS – B:­ This covers all mechanical protections of the turbine in which turbine will be tripped first and following
this generator will trip on reverse power / low forward power protections.
CLASS – C:­ This covers electrical protection for faults in the system in which generator will be unloaded by tripping
of generator breaker only. The unit will come to house load operation and the UAT will be in
service. Various protections of this class are:
i) 220 KV (HV side of Generator Transformer) busbar protection.
ii) Generator Transformer HV side breaker pole discrepancy.
iii) Generator negative phase sequence protection
iv) Generator Transformer over current / Earth fault protection
v) Reverse power protection without turbine trip.

[http://1.bp.blogspot.com/­ygd5AXAkGL0/UcamR­
0JEuI/AAAAAAAACaQ/3LR7hMkQ0jw/s1600/8.jpg]
1) Generator Differential Protection (87 G): ­
It is unit type protection, covering the stator winding for phase to phase faults due to breakdown of insulation between
stator phase windings. This relay is not sensitive for single line to earth faults as the earth fault current is limited due
to the high neutral earthing resistance.
http://powerplantpro.blogspot.in/2014/03/generator­protection­explained.html 2/9
12/5/2016 Generator Protection Explained

If CTs of identical ratios are used on neutral and line side of generator, an operating current setting of 20% it can be
adopted. It is instantaneous in operation and it trips the generator breaker (Class – A) to eliminate the system in –
feed to the fault along with field breaker and turbines.

For all machines of ratings 10 MVA and above, this protection shall be provided.

[http://3.bp.blogspot.com/­pqkySaNmDmc/UcanTiU9znI/AAAAAAAACac/irQYlYMk_r0/s1600/9.jpeg]
2) Generator – Transformer Differential Protection (87T):­
This is similar to Generator Differential Protection, which covers from the generator terminals upto the HV
breaker of generator transformer. . Sometimes this relay is not provided where Generator and Generator
Transformer Overall Differential relay (87O) is provided. 87G & 87T functions should have the features of through
fault restraint, magnetising inrush restraint.

3) Generator & Generator Transformer Overall Differential Protection (87O):

Besides generator differential and generator transformer differential, an overall differential relay can be provided
between generator neutral side CTs and generator transformer Hv side CTs (and HV side CTs of UAT if provided)
covering both generator and generator transformer. The principle of operation of above relay is similar to any
differential relay and it is also termed as unit differential relay.

4) Backup impedance Protection (21G):­

This operates for phase faults in the unit, in the HV yard or in the adjacent transmission lines, with a suitable
time delay. It operates as a backup when the corresponding main protection fails.

http://powerplantpro.blogspot.in/2014/03/generator­protection­explained.html 3/9
12/5/2016 Generator Protection Explained

[http://2.bp.blogspot.com/­
mZKdLE5ohAk/UcaoNkV48LI/AAAAAAAACao/dXe71Vc7cfQ/s1600/images.jpg]

5) Voltage restrained overcurrent protection (51 / 27 G):­

This will operate when the fault current from the generator terminals becomes low due to excitation system
characteristic with under voltage criteria.
It operates as a backup protection for system faults with suitable time delay.

6) Negative phase sequence protection (46 G):­

It safeguards the generator rotor against over heating caused by the induced double frequency (100 Hz)
currents when negative phase sequence currents are present in the stator. The negative phase sequence
current(I2) can appear due to unbalanced single phase loads or transmission line unsymmetrical faults
It should be set according the Negative Phase Sequence capability of the generator
I2**2 xt = 30 for Thermal Units
= 40 for Hydro Units
Alarm stage can be set at 50% of continuous withstand capability of the machine with a time delay of 3 to 5
Sec.

7) Generator overloads protection (51G);­

It is used as an additional check of the stator winding temperature high protection. The relay can be
connected
For alarm with a setting of 110% .
For trip with a setting of 125% with due time delay

8) Generator Stator Earth Fault Protection (64G):­

The high neutral earthing resistance arrangement limits the generator earth fault current, minimising the
damage to core laminations. Although a single phase earth fault is not critical, it requires clearance within a
short time due to:
i) It may develop into a phase to phase fault
ii) If a second earth fault occurs the current is not longer limited by the earthing resistor.
iii) Fire may result from earth fault arc.

http://powerplantpro.blogspot.in/2014/03/generator­protection­explained.html 4/9
12/5/2016 Generator Protection Explained

[http://2.bp.blogspot.com/­
_4NqZER1hvU/Ucaq2SzKzGI/AAAAAAAACbA/zNYTW0ngdiA/s1600/2.JPG]
a) 95% stator earth fault protection (64G1)
It is an over voltage relay monitoring the voltage developed across the secondary of the neutral grounding
transformer in case of ground faults. It covers generator, LV winding of generator transformer and HV winding of
UAT. A pickup voltage setting of 5% is adopted with a time delay setting of about 1.0 Sec. For all machines of ratings
10 MVA and above this shall be provided.

b) 100% stator earth fault protection (64G2);­

This is a 3rd harmonic U/V relay. It protects 100% of stator winding.During the machine running condition
there will be certain third harmonic voltage at neutral side of the generator.This 3rd harmonic voltage will come down
when a stator earth fault occurs causing this relay to operate. This shall have voltage check or current check unit, to
prevent faulty operation of the relay at generator stand still or during the machine running down period.

9) Loss of Excitation (40G):­

In case of loss of excitation, the generator goes out of synchronism and starts running asynchronously at a speed
higher than the system, absorbing reactive power from the system. Under these conditions, the stator end regions
and part of the rotor get over heated.
This protection shall have:
i) Mho characteristic lying in 3rd and 4th quadrants of impedance diagram with adjustable reach and offset.
ii) An under voltage and / or overcurrent relay as additional check.
iii) A timer with adjustable range of 1­10 Sseconds.
Recommended Settings:­
­ Diameter of Mho circle =Xd
­ Off set of Mho circuit from the origin = xd1/2
­ Time delay = 1 Sec.
­ Under voltage relay = 110 – 115% of
generator rated current

10) Low Forward Power Relay (37G):­

In thermal machines, when the steam flow through turbine is interrupted by closing the ESVs or the governor
valves, the remaining steam in the turbine generates (low) power and the machine enters to motoring conditions
http://powerplantpro.blogspot.in/2014/03/generator­protection­explained.html 5/9
12/5/2016 Generator Protection Explained

drawing power from the system. This protection detects low forward power conditions of the generator and trips
generator breaker after a time delay, avoiding motoring of generator
The low forward power relay will be provided with ‘turbine trip’ interlock in thermal machines. A setting of 0.5%
of rated active power of generator with a time delay of 2.0 Sec. shall be adopted.

11) Reverse Power relay (32G):­

Reverse power protection shall be used for all types of generators. When the input to the turbine is interrupted
the machine enters into motoring condition drawing power from the system. Reverse power relay protects the
generators from motoring condition. In thermal machines, reverse power condition appears subsequent to low
forward power condition.
For reverse power relay, a setting of 0.5% of rated active power of generator with 2 stage timer as given below.
i) Stage – I: ­ With turbine trip interlock, a time delay of 2 Sec. shall be adopted.
ii) Stage – II:­ Without ‘ turbine trip’ interlock, a time delay of about 20 Sec. can be adopted to avoid
unnecessary tripping of unit during system disturbance causing sudden rise in frequency or power
swing conditions.
12) Rotor earth fault protection: ­
This protection shall be provided for machines of all sizes. This protection shall be connected for alarm and
the operator may take the machine at the earliest opportunity after the first earth fault has occurred. This
protection will have a sensitive voltage function operating on bridge measurement basis with auxiliary equipment. It
will have two levels, one for alarm and one for trip. The settings adopted in general are:
i) For alarm : 25 KJ Ohm, 1.0 Sec.
ii) For trip : 5 K Ohm, 0.5 Sec.

[http://3.bp.blogspot.com/­
AxZTnbHqyYw/UcasaH5Y3pI/AAAAAAAACbU/bJdK1w3uaLQ/s1600/3.JPG]
A
[http://3.bp.blogspot.com/­AxZTnbHqyYw/UcasaH5Y3pI/AAAAAAAACbU/bJdK1w3uaLQ/s1600/3.JPG]modern generating
unit is a complex system comprising the generator stator winding and associated transformer and unit
transformer, the rotor with its field winding and exciters, and the turbine and its associated condenser
and boiler complete with auxiliary fans and pumps. Faults of many kinds can occur within this system
for which diverse protection applied will be governed by economic considerations, taking into account
the value of the machine and its importance to the power system as a whole

http://powerplantpro.blogspot.in/2014/03/generator­protection­explained.html 6/9
12/5/2016 Generator Protection Explained

13) Pole Slip Relay (98 G):

The pole slipping relay is designed to protect synchronous generators against the possibility of
the machine running unstable region of the ‘power angle curve’ which would result in power
oscillations and pole slip. Pole slipping of generators with respect to the system leading to an
increase in rotor angular position beyond the generator transient stability limits. Some of the
causes for pole slipping are as follows.
i) Large network disturbance
ii) Faults on the network close to the generator.
iii) Loss of generator field.
iv) Operating the generator in an excessive under excited mode.
v) Loss of evacuation.
Setting recommendations:­
a) If the source of oscillation lies between generator/transformer unit, the machine has to be
isolated from the network after the first slip.
Forward reach of relay characteristics shall cover generator/generator transformer. Tripping in this zone shall be
in the first pole slip. The reach of this zone is =0.7x d’
b) If the source of oscillation lies outside the unit in the network, the generator should not be
switched off until several pole slips have recurred.

14) Generator Under Frequency Protection (81 G):

The Under Frequency Protection:
­ Prevents the steam turbine and generator from exceeding the permissible operating time at
reduced frequencies.
­ Ensures that the generating unit is separated from the network at a preset value of frequency.
­ Prevent overfluxing (v/f) of the generator (large overfluxing for short times).
The stator under frequency relay measures the frequency of the stator terminal voltage.
Setting Recommendations:­
For Alarm : 48.0 Hz, 2.0 Sec. time delay.
For Trip : 47.5 Hz, 1.0 Sec. (or)
As recommended by Generator Manufacturers.

15) Generator Over voltage Protection (59 G):

An over voltage on the terminals of the generator can damage the insulator of the generator,
bus ducting, breakers, generator transformer and auxiliary equipment. Hence over voltage
protection should be provided for machines of all sizes.
Settings recommendations:­
Stage­I : Over voltage pickup = 1.15 x Un
Time delay = 10 Sec.

State­II : Over voltage pickup = 1.3 x Un

Time delay = 0.5 Sec.

16) Standby Earth Fault Protection (51 NGT)

This relay monitors the current in the generator transformer neutral. It can detect earth faults in
the Transformer HV side or in the adjacent network.

http://powerplantpro.blogspot.in/2014/03/generator­protection­explained.html 7/9
12/5/2016 Generator Protection Explained

Setting recommendations:­
As this relay pickup for faults in the system, it has to be time graded with the transmission lines
emanating from that generating station. Normally IDMT relay is provided
Operating Current Setting = 20% In
Operating Time = 1.5 to 2.0 Sec.
(or)
Greater than (max.) Zone­3 time of adjacent
Transmission Lines.
The following hazards require consideration.
a) Stator insulation faults
b) Overload
c) Overvoltage
d) Unbalanced loading
e) Rotor faults
f) Loss of excitation
g) Loss of synchronism
h) Failure of prime mover
i) Low vacuum
j) Lubrication oil failure
k) Loss of boiler firing
l) Overspeeding
m) Rotor distortion
n) Difference in expansion between rotating and stationary parts
o) Excessive vibration
Small capacity induction generators also are in service, mostly mini hydel and windmills of
capacity of 200KW to 2000KW, which depend on the system for excitation. Their protection
requirements are very simple such as overcurrent relays.
The protective relays generally used for the synchronous generators are listed at in the
following page.
Instead of independent relays for each function, microprocessor based numerical relay,
which can take care of the entire Generator protections the latest entry.

PROTECTIVE SCHEMES FOR VARIOUS GENERATORS

http://powerplantpro.blogspot.in/2014/03/generator­protection­explained.html 8/9
12/5/2016 Generator Protection Explained

[http://4.bp.blogspot.com/­
Ea39QBivvyY/UcbkXuRSAsI/AAAAAAAACdg/PN1tx9iCPVQ/s1600/2.jpg]

Posted 30th March 2014 by Irfan Akhtar

0 Add a comment

Enter your comment...

Comment as: Unknown (Google) Sign out

Publish Preview Notify me

http://powerplantpro.blogspot.in/2014/03/generator­protection­explained.html 9/9