AJA Hi5-Fiber Manual v2.3
AJA Hi5-Fiber Manual v2.3
Hi5-Fiber
Mini-Converter
Version 2.3
Published October 20, 2023
Notices
Trademarks
AJA® and Because it matters.® are registered trademarks of AJA Video Systems, Inc.
for use with most AJA products. AJA™ is a trademark of AJA Video Systems, Inc. for
use with recorder, router, software and camera products. Because it matters.™ is a
trademark of AJA Video Systems, Inc. for use with camera products.
CION®, Corvid Ultra®, lo®, Ki Pro®, KONA®, KUMO®, ROI® and T-Tap® are registered
trademarks of AJA Video Systems, Inc.
AJA Control Room™, KiStor™, Science of the Beautiful™, TruScale™, TruZoom™,
V2Analog™ and V2Digital™ are trademarks of AJA Video Systems, Inc.
All other trademarks are the property of their respective owners.
Copyright
Copyright © 2023 AJA Video Systems, Inc. All rights reserved. All information in
this manual is subject to change without notice. No part of the document may be
reproduced or transmitted in any form, or by any means, electronic or mechanical,
including photocopying or recording, without the express written permission of AJA
Video Systems, Inc.
Contents
Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Copyright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Contacting AJA Technical Support or Sales . . . . . . . . . . . . . . . . . . . . . . . 2
Chapter 1 – Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
I/O Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Lock LED Status Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
User Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Mini-Config Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Chapter 2 – Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
USB Control and Setup—Using AJA Mini-Config . . . . . . . . . . . . . . . . . . . 7
Acquiring Mini-Config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installing Mini-Config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Running Mini-Config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Operating Mini-Config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Tabbed Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Input Tab Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Output Tab Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Audio Tab Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Update Tab Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Software Update Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Info Tab Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Appendix A – Specifications . . . . . . . . . . . . . . . . . . . . . . . . 17
Hi5-Fiber Tech Specs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Chapter 1 – Introduction
Overview
The Hi5-Fiber converts 3G, HD, and SD-SDI over single mode 1310 nm fiber optic
cable (ST-style connection) to HDMI for driving HDMI monitors. Embedded 8
channel SDI audio is supported in the HDMI output allowing a convenient single
cable audio/video connection. The Hi5-Fiber provides 2 channel RCA style audio
outputs for separate audio monitoring if needed.
Features
• SDI over Fiber to HDMI (see "Specifications" on page 17 for a complete list of
supported inputs).
• Full HDMI support including 10-bit video and 8 channels of embedded audio
• Supports single mode 1310 nm fiber optic cable with ST receiver
• Additional 2 Channel RCA jack audio output (selectable channel pairs)
• HDMI cable supplied
• Uses universal input +5V power supply AJA model DWP-U-R1 (included)
• USB configuration port.
Block Diagram
Figure 1. Hi5-Fiber Converter, Simplified Block Diagram
Optical
Fiber Optical
ST Input Receiver
(3G-SDI)
USB Port
(connect to MiniConfig Control
Audio Audio 2-Channel
PC or Mac) Analog Audio
Delay D/A
Monitor Output
I/O Connections
Figure 2. Hi5-Fiber Converter Connections
HDMI
Output
Fiber Connector
Input
Connector
Signal
Presence
Lock LED
2 Channel
USB Unbalanced
Port Analog Audio
Out (RCA Jacks)
Power
LED
DC
Power
Input
User Controls
Mini-Config Control
Automatic input format detection configures the unit automatically to match
input and output video parameters. In most cases, manual configuration is not
necessary. Advanced Mini-Config control supports color space and bit depth
adjustments, and audio channel selection.
Configuration set via Mini-Config is stored in the Hi5-Fiber unit through
subsequent power cycles.
Installation
Typically, Hi5-Fiber installation consists of the following steps:
1. Ensure the converter is disconnected from power.
2. Connect video equipment to the Fiber ST connector and HDMI connector
3. Connect audio equipment to RCA connectors (optional)
4. Apply power to the converter (AJA power supply included).
5. The converter will now run using the default factory settings. If you wish to
alter the factory settings, you’ll need to:
• Install the AJA Mini-Config software on your computer
• Attach the converter via USB
• Make your changes using Mini-Config setup screens.
• This process is detailed in "USB Control and Setup—Using AJA Mini-Config" on
page 7.
Chapter 2 – Operation
Acquiring Mini-Config
AJA’s Mini-Config application is available for download from the AJA website.
To download the latest Mini-Config package, which includes the Mini-Config
application, Mini-Converter firmware, and documentation, go to:
https://www.aja.com/products/mini-config-software
Select either the Windows or Mac icon to download the desired version.
Mini-Converter Documentation
Included with the Mini-Config package is a complete set of documentation for
all Mini-Converters supported by Mini-Config. A .PDF of the Installation and
Operation Guide for the currently connected Mini-Converter can be accessed from
the Mini-Config UI via the Help/Manual drop-down menu.
Documentation for all AJA Mini-Converters that use Mini-Config can also be
accessed directly in the Mini-Config download package Documentation folder,
and via the Documentation icon available on the Mac installer.
Documentation (and firmware) included with the Mini-Config application are the
versions available at the time of distribution. However, Mini-Converter software,
firmware and documentation are updated regularly, so newer versions may exist.
To download the latest documentation for an individual Mini-Converter, go to:
https://www.aja.com/family/mini-converters
and navigate to the Support webpage of that Mini-Converter.
Installing Mini-Config
PC Installation
NOTE: If you have an older version of Mini-Config software installed on your PC, AJA
recommends uninstalling the older version before installing the current version.
To install Mini-Config on a Windows PC:
1. Download the application from the AJA website (select the Windows icon
on the Mini-Config Support web page).
2. Open the AJA_MiniConfig.zip file
3. Double-click on the MiniInstaller.msi file.
4. A Setup Wizard will guide you through the installation.
5. Click Next to begin. Answer the questions in the subsequent dialogs. When
finished, an AJA Mini-Config shortcut will be installed on the desktop, and
you will be able to locate the Mini-Config application in the AJA folder in
the Programs listing.
NOTE: If the same version of the Mini-Config application already exists on the PC, a
different Setup Wizard appears.
With this screen you can Repair (reinstall) or Remove (uninstall) Mini-Config on
the PC.
Mac Installation
NOTE: Intel and Apple Silicon (M1/M2) based CPUs are supported for use with AJA Mini-
Config software.
Running Mini-Config
Connect the Mini-Converter to the PC or Mac via the supplied USB cable. Connect
the external power supply (supplied) to the Mini-Converter.
PC Startup
To run Mini-Config on a PC, double-click on the AJA Mini-Config icon on your
desktop, or open the AJA folder in the program list and click on the AJA Mini-
Config application located inside the Mini-Config folder.
Figure 6. Mini-Config PC Startup icon and Folder Location
Mac Startup
To run Mini-Config on a Mac, open the Applications folder and locate the AJA
Mini-Config application. Double-click the application to launch it.
Saving Setups
A File drop down menu on the Mini-Config application bar (similar for Mac and
PC) allows you to save the current state of the Mini-Converter to a preset file for
later recall.
Using this feature you can set up the converter for different applications, storing
each configuration (Save Preset As...) with a unique name for easy recall (Open
Preset...).
A Revert to Factory Settings menu item similarly allows you to change the
settings back to AJA’s factory defaults.
Operating Mini-Config
The Mini-Config application provides a graphic interface for viewing settings
and updating software. It consists of an information area at the top that shows
the available Mini-Converters attached to the computer via USB, with a graphical
rendering of the selected Mini-Converter showing all the connectors and their
current state.
Colored text next to the connectors indicates the signal type and what the Mini-
Converter is doing:
• Blue text indicates the values automatically selected
• Black text indicates values that you have manually selected
• Red text indicates the Mini-Converter is not detecting a signal, or cannot
operate with the current user settings.
NOTE: Even if no output device is detected, the SDI connector text still shows the signal it
is outputting.
NOTE: Configuration settings in red will change based on the attached output device as
well as input signals. For improved accuracy and reliability, you should configure
the Mini-Converter only when the target output device is attached and input
signals are supplied at the inputs.
Screens are virtually the same on both PC and Mac, with subtle differences that
reflect the general look of the platform environment.
Figure 7. Example Mini-Config Screen
Each connector is
labeled with the
signals currently
detected or
manually selected.
Firmware Version
and Serial Number
Tabbed Screens
Status Message
NOTE: The LOCK LED indicates valid input video by color. Off is no signal, green is SD
video, red is HD video, amber is 3G video.
Selecting a Mini-Converter with the pulldown menu causes this application to
connect to the selected converter. The graphic of Mini-Converter and text below
it provides:
• Type of converter
• Firmware version
• Serial number of the unit.
A status field at the bottom of the screen shows if your application is connected
and communicating with the Mini-Converter.
When configuring the Mini-Converter, select it from the top pulldown, view the
current settings and change any values. Making a change communicates that
new value to the Mini-Converter’s non-volatile memory.
Tabbed Screens
The Tabs delineate control screens with groups of controls for each type of task to
be performed. The controls for the actual configuration parameters are specific
to each Mini-Converter type. When you Click on any of the tab buttons, the pane
below the tabs will change to match your tab selection. Any changes you make
are immediately applied and will be saved, overwriting previous settings.
Click on the Input tab to view and make changes to the converter’s input settings.
Color Space - Selects the Input Video Color Space. Choose Auto, 422 YCbCr, or
444 RGB, or 444 YCbCr. Choosing “Auto” will automatically select color mode
based on the input video parameters and the payload ID.
RGB Range - Selects the Input Video Color Range. Choose SMPTE or Full range.
NOTE: The RGB range setting effects input range only when in RGB mode. YCbCr inputs
are always SMPTE levels.
Bit Depth - Selects the input video bit depth. Choose Auto, 8-bit, 10-bit, or 12-bit.
Choosing “Auto” automatically selects the bit depth based on the input video
parameters and payload ID.
Video Format - Selects the Input Video Format. Choose from Auto, Progressive
(P), Interlaced, or PsF (progressive segmented frame). Choosing “Auto”
automatically selects the format based on the input video parameters and the
payload ID.
3G-B Mode - Selects the 3G level B Video Mode. Choose from the following:
• Auto - automatically selects the format based on the input video parameters.
• Dual Link - select this when your 3G signal is carrying 444 information or 12 bit
data.
NOTE: The following two settings only apply to 3G-B video in Dual Stream mode.
• 1 x HD DS1 - use only Data Stream 1 as a single video .
• 1 x HD DS2 - use only Data Stream 2 as a single video.
Click on the Output tab to view and make changes to the Hi5-Fiber Output
settings.
Color Space - Selects the desired output video format. Choose from the
following:
• Auto - selects the video format based on the input video and the attached
device’s capabilities.
• 4:2:2 YCbCr
• 4:4:4 RGB
• 4:4:4 YCbCr
Bit Depth - Choose from Auto, 8-bit, 10-bit, or 12-bit. Choosing “Auto”
automatically selects the bit depth based on the input video and the attached
device’s capabilities.
RGB Range - Choose Auto, SMPTE or Full. Choosing “Auto” automatically selects
the output color range setting.
NOTE: The RGB range setting effects output range only when in RGB mode. YCbCr
outputs are always SMPTE levels.
2K Crop - Choose Auto, Off, or On. Provides the option of center cutting 2Kx1080
video signals to make 1920x1080. This has no effect when input video is 1920
pixels per line.
Color Dithering - Choose Off or On.
HDMI/DVI - Choose Auto, HDMI, or DVI. When DVI is selected, any audio signals
present are not passed. Choosing “Auto” automatically selects the output
mode based on the attached device’s capabilities.
Click on the Audio tab to view and make changes to the Hi5-Fiber audio settings.
When using the DVI video protocol no audio is output, since that protocol is video
only.
Input Source - Choose which embedded audio channels are routed to the HDMI
output. Eight channels are routed at a time. You can choose Ch 1-8 or Ch 9-16
from the SDI input.
Output Channel Count - Choose Auto, 2 of 8 channels or 8-channel embedded
audio. Choosing “Auto” automatically selects the audio channels based on the
attached device’s capabilities.
Analog Audio Select - Permits selecting the pair of audio channels to be sent
to the analog audio RCA connectors. The audio pairs routed depend on the
Input Source (1-8 or 9-16) setting above. Choose Ch 1-2 (or 9-10), through Ch
7-8 (or 15-16).
Audio Offset In Frames - Permits time shifting the embedded audio in
relationship to the video (for example, to correct for lip sync problems), in
1/16 of a frame increments. Range is from 0 video frame to +7 video frames.
The actual time duration of delay will vary depending on the frame rate of the
format being converted.
NOTE: One frame of delay is automatically added when the input video is PsF.
Use this Update screen to view the software version currently installed on the
converter or install new software.
NOTE: When discussing Mini-Converters, “Firmware” is software that will be stored in
the Mini-Converter’s non-volatile memory and used when it is powered up. This
is something different than the Mini-Config application software. The version
numbers shown in the Update screen refer only to the firmware.
Installed - This field shows the version of the firmware currently installed inside
the Mini-Converter.
Desired - This field shows the version of firmware embedded in the Mini-Config
application which you can install into the Mini-Converter by clicking the
Update button.
Update - This button initiates a software update operation loading the “Desired”
version of firmware into the Mini-Converter’s non-volatile memory.
Progress - This indicator bar shows the progress of firmware installation.
This screen provides basic information about the Mini-Converter. This information
is mostly useful when calling AJA Support for service or technical support.
Name - This field allows you to give your Mini-Converter a name. This can be
useful if you have several Mini-Converters attached to a Mac/PC via USB
so you can distinguish between them easily (especially if they’re the same
model).
Type - This is the factory set model name of the Mini-Converter.
Assembly - This is the factory assembly number.
NOTE: Some newly manufactured Mini-Converters may not be backwards compatible
with older firmware and Mini-Config versions. It is highly recommended that
you update the firmware to avoid any potential issues. Please check the current
Release Notes to confirm that the Assembly number is compatible with any older
firmware or Mini-Config versions.
Serial Number - This is the factory set unique serial number of your Mini-
Converter. If you ever call AJA for customer support, you will need to reference
this number.
Set Name - This button saves the information entered in the Name field.
Appendix A – Specifications
Hi5-Fiber Tech Specs
Video Formats
• (2K) 2K x 1080p 23.98, 24, 25, 29.97, 30, 50, 59.94, 60
• (2K) 2K x 1080PsF* 23.98, 24, 25, 29.97, 30
• (HD) 1080i 50, 59.94, 60
• (HD) 1080p 23.98, 24, 25, 29.97, 30, 50, 59.94, 60
• (HD) 1080PsF* 23.98, 24, 25, 29.97, 30
• (HD) 720p 50, 59.94, 60
• (SD) 625i
• (SD) 525i
*NOTE: converts to progressive
Video Inputs
• Single mode optical fiber, ST connector supporting SMPTE-259/292/424 HD/
SD-SDI
Video Outputs
• HDMI with embedded audio up to 8-Channels (selectable by Mini-Config)
• 12-bit
• 10-bit YCbCr 4:2:2
• 8-bit RGB 4:4:4
Audio Input
• SDI embedded audio, select from 16-Channels
Audio Output
• 2-Channel RCA style (-10dBu nominal)
Size (w x d x h)
• 4.6" x 2.4" x 1.0" (116.84 x 60.96 x 25.4 mm)
Weight
• 0.4 lb (0.2 kg)
Power
• Uses AJA power supply model DWP-U-R1, included with purchase
• 100-240V, 50/60 Hz universal input
• +5V DC regulated, 3W
Environment
• Safe Operating Temperature: 0 to 40 C (32 to 104 F)
• Safe Storage Temperature (Power OFF): -40 to 60 C (-40 to 140 F)
• Operating Relative Humidity: 10-90% noncondensing
• Operating Altitude: <3,000 meters (<10,000 feet)
FCC Caution
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Declaration of Conformity
Marking by these symbols indicates compliance with the Essential Requirements
of the EMC Directive of the European Union 2014/30/EU.
Recycling Notice
This symbol on the product or its packaging indicates that this product
must not be disposed of with your other household waste. Instead, it is your
responsibility to dispose of your waste equipment by handing it over to a
designated collection point for the recycling of waste electrical and electronic
equipment. The separate collection and recycling of your waste equipment
at the time of disposal will help conserve natural resources and ensure that
it is recycled in a manner that protects human health and the environment.
For more information about where you can drop off your waste for recycling,
please contact your local authority, or where you purchased your product.
This is a Class A product based on the standard of the VCCI Council (VCCI V-3/2011
to 2015). If this equipment is used in a domestic environment, radio interference
may occur, in which case, the user may be required to take corrective actions.
Warning! Do not use this device near water and clean only with a dry cloth.
Avertissement! N'utilisez pas cet appareil près de l'eau et nettoyez-le seulement
avec un tissu sec.
Warnung! Das Gerät nicht in der Nähe von Wasser verwenden und nur mit einem
trockenen Tuch säubern.
¡Advertencia! No utilice este dispositivo cerca del agua y límpielo solamente con
un paño seco.
Aviso! Não utilize este dispositivo perto da água e limpe-o somente com um pano
seco.
Avviso! Non utilizzare questo dispositivo vicino all'acqua e pulirlo soltanto con un
panno asciutto.
Warning! Do not block any ventilation openings. Install in accordance with the
manufacturer's instructions.
Avertissement! Ne bloquez aucune ouverture de ventilation. Suivez les
instructions du fabricant lors de l'installation.
Warnung! Die Lüftungsöffnungen dürfen nicht blockiert werden. Nur gemäß den
Anweisungen des Herstellers installieren.
¡Advertencia! No bloquee ninguna de las aberturas de la ventilación. Instale de
acuerdo con las instrucciones del fabricante.
Aviso! Não obstrua nenhuma das aberturas de ventilação. Instale de acordo com as
instruções do fabricante.
Avviso! Non ostruire le aperture di ventilazione. Installare in conformità con le
istruzioni del fornitore.
Warning! Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
Avertissement! N'installez pas l'appareil près d'une source de chaleur telle que des
radiateurs, des bouches d'air de chauffage, des fourneaux ou d'autres appareils
(amplificateurs compris) qui produisent de la chaleur.
Warnung! Nicht in der Nähe von Wärmequellen wie Heizkörpern, Heizregistern,
Öfen oder anderen Wärme erzeugenden Geräten (einschließlich Verstärkern)
aufstellen.
¡Advertencia! No instale cerca de fuentes de calor tales como radiadores, registros
de calor, estufas u otros aparatos (incluidos amplificadores) que generan calor.
Aviso! Não instale perto de nenhuma fonte de calor tal como radiadores, saídas
de calor, fogões ou outros aparelhos (incluindo amplificadores) que produzam
calor.
Avviso! Non installare vicino a fonti di calore come termosifoni, diffusori di aria
calda, stufe o altri apparecchi (amplificatori compresi) che emettono calore.
Warning! Since the Mains plug is used as the disconnection for the device, it must
remain readily accessible and operable.
Avertissement! Puisque la prise principale est utilisée pour débrancher l'appareil,
elle doit rester aisément accessible et fonctionnelle.
Warnung! Da der Netzstecker als Trennvorrichtung dient, muss er stets zugänglich
und funktionsfähig sein.
¡Advertencia! Puesto que el enchufe de la red eléctrica se utiliza como dispositivo
de desconexión, debe seguir siendo fácilmente accesible y operable.
Aviso! Dado que a ficha principal é utilizada como a desconexão para o dispositivo,
esta deve manter-se prontamente acessível e funcional.
Avviso! Poiché il cavo di alimentazione viene usato come dispositivo di
sconnessione, deve rimane prontamente accessibile e operabile.
Warning! Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the device.
Avertissement! Protégez le cordon d'alimentation pour que l'on ne marche
pas dessus ou qu'on le pince, en particulier au niveau des prises mâles, des
réceptacles de convenance, et à l'endroit où il sort de l'appareil.
Warnung! Vermeiden Sie, dass auf das Netzkabel getreten oder das Kabel geknickt
wird, insbesondere an den Steckern, den Steckdosen und am Kabelausgang am
Gerät.
¡Advertencia! Proteja el cable de corriente para que no se le pise ni apriete, en
especial cerca del enchufe, los receptáculos de conveniencia y el punto del que
salen del equipo.
Aviso! Proteja o cabo de alimentação de ser pisado ou de ser comprimido
particularmente nas fichas, em tomadas de parede de conveniência e no ponto
de onde sai do dispositivo.
Avviso! Proteggere il cavo di alimentazione in modo che nessuno ci cammini sopra
e che non venga schiacciato soprattutto in corrispondenza delle spine e del
punto in cui esce dal dispositivo.
Warning! Unplug this device during lightning storms or when unused for long
periods of time.
Avertissement! Débranchez cet appareil pendant les orages avec éclairsou s'il est
inutilisé pendant de longues périodes.
Warnung! Das Gerät ist bei Gewitterstürmen oder wenn es über lange Zeiträume
ungenutzt bleibt vom Netz zu trennen.
¡Advertencia! Desenchufe este dispositivo durante tormentas eléctricas o cuando
no se lo utilice por largos periodos del tiempo.
Aviso! Desconecte este dispositivo da tomada durante trovoadas ou quando não é
utilizado durante longos períodos de tempo.
Avviso! Utilizzare soltanto i collegamenti e gli accessori specificati e/o venduti dal
produttore, quali il treppiedi e l'esoscheletro.
Warning! Do not open the chassis. There are no user-serviceable parts inside.
Opening the chassis will void the warranty unless performed by an AJA service
center or licensed facility.
Avertissement! Ne pas ouvrir le châssis. Aucun élément à l’intérieur du châssis
ne peut être réparé par l’utilisateur. La garantie sera annulée si le châssis est
ouvert par toute autre personne qu’un technicien d’un centre de service ou d’un
établissement agréé AJA.
Warnung! Öffnen Sie das Gehäuse nicht. Keine der Geräteteile können vom
Benutzer gewartet werden. Durch das Öffnen des Gehäuses wird die Garantie
hinfällig, es sei denn, solche Wartungsarbeiten werden in einem AJA-Service-
Center oder einem lizenzierten Betrieb vorgenommen.
¡Advertencia! No abra el chasis. El interior no contiene piezas reparables por el
usuario. El abrir el chasis anulará la garantía a menos que se lo haga en un centro
de servicio AJA o en un local autorizado.
Advertência! Não abra o chassi. Não há internamente nenhuma peça que permita
manutenção pelo usuário. Abrir o chassi anula a garantia, a menos que a abertura
seja realizada por uma central de serviços da AJA ou por um local autorizado.
Avvertenza! Non aprire lo chassis. All’interno non ci sono parti riparabili
dall’utente. L’apertura dello chassis invaliderà la garanzia se non viene effettuata
da un centro ufficiale o autorizzato AJA.
Warning! Disconnect the external AC power supply line cord(s) from the mains
power before moving the unit.
Avertissement! Retirez le ou les cordons d’alimentation en CA de la source
d’alimentation principale lorsque vous déplacez l’appareil.
Warnung! Trennen Sie die Wechselstrom-Versorgungskabel vom Netzstrom, bevor
Sie das Gerät verschieben.
¡Advertencia! Cuando mueva la unidad desenchufe de la red eléctrica el/los
cable(s) de la fuente de alimentación CA tipo brick.
Advertência! Remova os cabos CA de alimentação brick da rede elétrica ao mover
a unidade.
Avvertenza! Scollegare il cavo dell’alimentatore quando si sposta l’unità.
Warning! Only use attachments and accessories specified and/or sold by the
manufacturer.
Avertissement! Utilisez seulement les attaches et accessoires spécifiés et/ou
vendus par le fabricant.
Warnung! Verwenden Sie nur Zusatzgeräte und Zubehör angegeben und / oder
verkauft wurde durch den Hersteller.
¡Advertencia! Utilice solamente los accesorios y conexiones especificados y/o
vendidos por el fabricante.
Aviso! Utilize apenas equipamentos/acessórios especificados e/ou vendidos pelo
fabricante.
Avviso! Utilizzare soltanto i collegamenti e gli accessori specificati e/o venduti dal
produttore.
Warning! AJA models that contain Class 1 Laser products use active fiber-optic
cables that emit radiation invisible to the human eye. Do not look directly at the
end of an active fiber-optic cable or the fiber connector.
Avertissement! Les modèles AJA contenant des produits laser de classe 1 utilisent
des câbles à fibres optiques actives qui émettent un rayonnement invisible à
l'œil humain. Ne regardez pas directement l'extrémité d'un câble à fibre optique
CLASS 1
LASER actif ou le connecteur de fibre.
PRODUCT
Warnung! AJA-Modelle, die Laserprodukte der Klasse 1 enthalten, verwenden
aktive Glasfaserkabel, die für das menschliche Auge unsichtbare Strahlung
aussenden. Schauen Sie nicht direkt auf das Ende eines aktiven Glasfaserkabels
oder den Glasfaserstecker.
¡Advertencia! Los modelos AJA que contienen productos láser de Clase 1 utilizan
cables de fibra óptica activos que emiten radiación invisible para el ojo humano.
No mire directamente al extremo de un cable de fibra óptica activo ni al
conector de fibra.
Advertência! Os modelos AJA que contêm produtos Laser Classe 1 utilizam cabos
de fibra óptica ativa que emitem radiação invisível ao olho humano. Não olhe
diretamente para a extremidade de um cabo de fibra óptica ativo ou para o
conector de fibra.
Avvertenza! I modelli AJA che contengono prodotti laser di Classe 1 utilizzano
cavi in fibra ottica attivi che emettono radiazioni invisibili all'occhio umano. Non
guardare direttamente l'estremità di un cavo in fibra ottica attivo o il connettore
in fibra.
Limitation of Liability
Under no circumstances shall AJA video BE LIABLE IN ANY WAY FOR ANY LOST,
CORRUPTED OR DESTROYED DATA, FOOTAGE OR WORK, OR FOR ANY OTHER
INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOST PROFITS,
OR FOR ANY THIRD PARTY CLAIM, IN CONNECTION WITH THE PRODUCT, WHETHER
RESULTING FROM DEFECTS IN THE PRODUCT, SOFTWARE OR HARDWARE FAILURE,
OR ANY OTHER CAUSE WHATSOEVER, EVEN IF AJA VIDEO HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. AJA VIDEO’S LIABILITY IN CONNECTION WITH THE
PRODUCT SHALL UNDER NO CIRCUMSTANCES EXCEED THE PURCHASE PRICE PAID
FOR THE PRODUCT. The foregoing limitations apply even if any remedy set forth in
this LIMITED WARRANTY fails of its essential purpose. SOME JURISDICTIONS DO NOT
ALLOW THE LIMITATION OF LIABILITY FOR PERSONAL INJURY, OR OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO SOME OR ALL OF THE TERMS OF THIS PARAGRAPH
MAY NOT APPLY TO YOU.
Index
Symbols R
2K Crop RGB Range
Output 13 Input 12
Output 13
A Running Mini-Config 9
AJA Support 2
Analog Audio Select S
RCA Connectors 14 Saving Setups 10
Audio Offset In Frames 14 SDI Over Fiber 4
Audio Tab Screen 14 Software Update Procedure 15
B U
Bit Depth Update Tab Screen 15
Input 12
Output 13 V
Video Format
C Input 12
Color Dithering
Output 13
Color Space
Input 12
Output 13
D
Documentation
Downloading 7
F
Fiber ST Connector 4, 5
H
HDMI/DVI
Output 13
I
Info Tab Screen 16
Input Source
Audio 14
Input Tab Screen 12
Installing Mini-Config 7
M
Mini-Config
Acquiring 7
Screen Description 11
Startup on Mac 10
Mini-Converter Documentation 7
O
Operating Mini-Config 10
Output Channel Count
Audio 14
Output Tab Screen 13