SCHEDULE OF LOADS FOR PANEL BOARD LEGEND & SYMBOLS

i 1 p SIZE OF PVC
CKT. LOAD DESCRIPTION VA LOAD VOLTS AMPERE CKT. BREAKER SIZE & TYPE OF COPPER CONDUCTOR
CONDUIT SERVICE ENTRANCE
h
FIRE EXIT 1 LIGHTING, 14PCS X 25W/PC 350 230 1.52 15 A 2-2.0MM² THHN + 1-2.0MM² THHN GROUND WIRE 20mm DIA.
c k PANEL BOARD
c
Sghi
J
2 LIGHTING, 11PCS X 25W/PC 275 230 1.2 15 A 2-2.0MM² THHN + 1-2.0MM² THHN GROUND WIRE 20mm DIA.
Sj Sk l CONV. OUTLET, 1500W/CKT 1500 230 6.52 20 A 20mm DIA.
b Sl 3 2-3.5MM² THHN + 1-3.5MM² THHN GROUND WIRE CIRCUIT BREAKER
FIRE EXIT

h LP Snop
4 CONV. OUTLET, 1500W/CKT 1500 230 6.52 20 A 2-3.5MM² THHN + 1-3.5MM² THHN GROUND WIRE 20mm DIA.
1 CIRCUIT HOMERUN
n p 5 SPARE 1000 230 4.35 20 A 20mm DIA.
d 2-3.5MM² THHN + 1-3.5MM² THHN GROUND WIRE
a a
6 SPARE 1000 230 4.35 20 A 2-3.5MM² THHN + 1-3.5MM² THHN GROUND WIRE 20mm DIA. LIGHTING OUTLET
g Sabc Sdef
TOTAL
Sm 5625 230 40 A 2-8.0MM² THHN + 1-5.5MM² THHN GROUND WIRE 20mm DIA.
2 S(3W) 3-WAY SWITCH
g f e f e m
FIRE EXIT SERVICE-ENTRANCE & FEEDER CALCULATION FOR PANEL BOARD:
o DUPLEX CONVENIENCE OUTLET
p VA LOAD = 350+275+1500+1500+1000+1000 = 5625 VA
I T = 5625 VA / 230 V x 0.80 DEMAND FACTOR = 19.57 A DUPLEX CONVENIENCE OUTLET,
o USE: 2-8.0MM² THHN + 1-5.5MM² THHN CU. IN 20 MM DIA. PVC WITH 40AT CIRCUIT BREAKER PROTECTION WP WEATHER -PROOF
FIRE EXIT
SPECIAL-PURPOSE OUTLET
LIGHTING LAYOUT PLAN USE: 2-8.0MM² THHN CU. FOR MAIN FEEDER
(AIRCON OR ELECTRIC RANGE)

SCALE 1:60 M 230V, 1-PH, 60-HZ + 1-5.5MM² THHN CU. FOR GROUNDING ELECTRODE CONDUCTOR
SPST SWITCH (LETTER INDICATE
S IDENTIFICATION & QYT. OF SWITCHES)
M
SERVICE DISCONNECT

SERVICE-ENTRANCE GROUND
PANEL BOARD
SPECIFICATIONS & GENERAL NOTES:
FIRE EXTINGUISHER

WP 1. ALL ELECTRICAL WORKS HEREIN SHALL BE DONE IN ACCORDANCE WITH THE LATEST EDITION OF THE
PHILIPPINE ELECTRICAL CODE (PEC), GUIDELINES & REGULATIONS OF THE OFFICE OF THE BUILDING
WP FIRE EXIT OFFICIAL (OBO/EE), AND SERVICE-ENTRANCE REQUIREMENT OF THE ELECTRIC POWER UTILITY COMPANY
3 L.O. L.O. (ANTECO).
2. ELECTRIC SERVICE TO THE BUILDING SHALL BE 230-VOLT, 60-HERTZ, SINGLE-PHASE, 2- WIRE.
4
3. TYPE OF WIRING SHALL BE RSC, EMT, OR PVC CONDUIT FOR SERVICE ENTRANCE AND PVC CONDUIT
FIRE EXIT

FOR BRANCH CIRCUITS.

C.O. C.O. 4. THE CONTRACTOR SHALL VERIFY AND ORIENT THE ACTUAL LOCATION OF SERVICE- ENTRANCE FOR
CONNECTION TO THE POWER SUPPLY.
5. ALL SERVICE-ENTRANCE EQUIPMENT, SWITCHES, PANEL BOARDS, CABINETS, MOTOR CASING, AND ALL
NON-CURRENT CARRYING METAL PARTS SHALL BE PROPERLY GROUNDED AND BONDED.
SPARE SPARE 6. ALL ELECTRICAL WORKS SHALL BE SUPPORTED INDEPENDENTLY AND NOT ON INSTALLATION OF THE
WP
OTHER TRADES. EXPOSED CONDUIT AND POWER CABLE RUNS SHALL BE INSTALLED PARALLEL TO OR
FIRE EXIT PERPENDICULAR WITH BUILDING LINE AND SUPPORTED BY CONDUIT CLAMPS OR BRACKETS.
TO GROUND 7. RECEPTACLES FOR GENERAL USE SHALL BE DUPLEX 15 A 250 VAC.
8. LIGHT SWITCHES MINIMUM RATING SHALL BE 15 A 250 VAC.
9. ALL MATERIAL TO BE USE SHALL BE BRAND NEW AND HAVE A "P.S." MARK.
10. MOUNTING HEIGHT ARE THE FF:
FIRE EXIT
A. LIGHT SWITCHES - 1.37M ABOVE FLOOR FINISH
B. CONVENIENCE OUTLETS - 0.30M ABOVE FLOOR FINISH, UNLESS SPECIFIED

POWER LAYOUT PLAN ONE-LINE DIAGRAM C. TELEPHONE OUTLETS

D. PANEL BOARD
-
-
0.30M ABOVE FLOOR FININSH
1.80M FROM FLOOR FINISH TO TOP OF PANEL
SCALE NTS
SCALE 1:60 M

11. ALL WORKS SHALL BE DONE UNDER THE DIRECT SUPERVISION OF A DULY LICENSED ELECTRICAL
ENGINEER (PEE/REE) OR A REGISTERED MASTER ELECTRICIAN (RME).
PRC NO : 0003605
PREPARED BY: PROJECT TITLE: APPROVED BY: SHEET CONTENT: REVISION: SHEET NO:
DATE ISSUED : 01/04/2023

HERMIE M. TACOGDOY ISSUED AT : SAN JOSE, ANTIQUE

PROPOSED ONE - STOREY
MALOU OBIDA AS SHOWN E
PROFESSIONAL ELECTRICAL ENGINEER VALIDITY : 11/13/2025 RESIDENTIAL BUILDING
1
PTR NO : 1128221 OWNER
I CERTIFY THAT THIS WORK WAS PREPARED BY ME
OR DONE UNDER MY DIRECT SUPERVISION TIN NO : 924-626-355 LOCATION: ASLUMAN HAMTIC, ANTIQUE