0% found this document useful (0 votes)
51 views

Quiz (Fluid) PDB Sir

Uploaded by

Aryan Singh
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
51 views

Quiz (Fluid) PDB Sir

Uploaded by

Aryan Singh
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

QUIZ (FLUID)

1. The length of needle floating on the surface of water is 1.5 cm. The force in addition to its weight required to
lift the needle from water surface will be (surface tension of water = 7.5 N/cm) :–
(A) 22.5 N (B) 2.25 N (C) 0.25 N (D) 225 N

2. The ring of radius 1m is lying on the surface of liquid. It is lifted from the liquid surface by a force of 4 Newtons
in such a way that the liquid film in it remains intact. The surface tension of liquid will be :–
1 1 1 1
(A) N/ m (B) N/ m (C) N/ m (D) N/ m
2  3 4

3. The radius of a soap bubble is r. The surface tension of soap solution is T. Keeping temperature constant, the radius
of the soap bubble is doubled, the energy necessary for this will be :–
(A) 24  r2 T (B) 8  r2 T (C) 12  r2 T (D) 16  r2 T

4. A liquid drop of diameter D breaks into 27 tiny drops. The resultant change in energy is :–
(A) 2TD2 (B) 4 TD2 (C) TD2 (D) None of these

5. The adjoining diagram shows three soap bubbles A, B and C prepared by blowing the capillary tube fitted with stop
cocks S, S1, S2 and S3 with stop cock S closed and stop cocks S1, S2 and S3 opened :–

CA

S1 S3 S2
S
A
A B

(A) B will start collapsing with volumes of A and C increasing


(B) C will start collapsing with volumes of A and B increasing
(C) C and A will both start collapsing with the volume of B increasing
(D) Volumes of A, B and C will become equal at equilibrium

6. Pressures inside two soap bubbles are 1.01 and 1.02 atmospheres. Ratio between their volumes is :–
(A) 102 : 101 (B) (102)3 : (101)3 (C) 8 : 1 (D) 2 : 1

7. An air bubble is lying just below the surface of water. The surface tension of water is 70 × 10–3 Nm–1 and atmospheric
pressure is 1.013 × 105 Nm–2. If the radius of bubble is 1 mm, then the pressure inside the bubble will be :–
(A) 1.0270 × 105 Pa (B) 1.0160 × 105 Pa (C) 1.0144 × 105 Pa (D) 1.0131 × 105 Pa

8. Two soap bubbles each of radius r are touching each other. The radius of curvature of the common surface will be:
(A) infinite (B) 2r (C) r (D) r/2

9. A soap bubble in vacuum has a radius of 3 cm and another soap bubble in vacuum has a radius of 4 cm. If the two
bubbles coalesce under isothermal condition, then the radius of the new bubble is :–
(A) 2.3 cm (B) 4.5 cm (C) 5 cm (D) 7 cm

10. Shape of meniscus for a liquid of zero angle of contact is :–


(A) Plane (B) Parabolic (C) Hemi–spherical (D) Cylindrical
11. If a water drop is kept between two glass plates, then its shape is :–

(A) (B) (C) (D) None the these

12. If a wax coated capillary tube is dipped in water, then water in it will –
(A) Rise up (B) Depress
(C) Sometimes rise and sometimes fall (D) Rise up and come out as a fountain

13. Water rises to a height h in a capillary at the surface of earth. On the surface of the moon the height of water column
in the same capillary will be :–
1
(A) 6h (B) h (C) h (D) zero
6

14. Two capillary tubes of same diameter are put vertically one each in two liquids whose relative densities are 0.8 and
0.6 and surface tensions are 60 dyne/cm and 50 dyne/cm respectively. Ratio of heights of liquids in the two tubes
h1
h 2 is :–

10 3 10 9
(A) (B) (C) (D)
9 10 3 10

15. In a capillary tube experiment, a vertical 30 cm long capillary tube is dipped in water. The water rises up to a height
of 10 cm due to capillary action. If this experiment is conducted in a freely falling elevator, the length of the water
column becomes :–
(A) 10 cm (B) 20 cm (C) 30 cm (D) Zero

16. Water rises to a height of 16.3 cm in a capillary of height 18 cm above the water level. If the tube is cut at a height
of 12 cm :–
(A) Water will come as a fountain from the capillary tube
(B) The height of the water in the capillary will be 12 cm
(C) The height of the water in the capillary will be 16.3 cm
(D) Water will flow down in it's arms
17. The height to which water rises in a capillary will be :–
(A) Maximum at 4° C (B) Maximum at 0° C (C) Minimum at 0° C (D) Minimum at 4° C

18. Water rises in a capillary upto a height h. If now this capillary is tilted by an angle of 45°, then the length of the
water column in the capillary becomes :–
h h
(A) 2h (B) (C) (D) h 2
2 2
19. If a capillary of radius r is dipped in water, the height of water that rises in it is h and its mass is M. If the radius
of the capillary is doubled the mass of water that rises in the capillary will be :–
M
(A) 4M (B) 2M (C) M (D)
2

20. Calculate the force required to separate the glass plate of area 10 –2 m 2 with a film of water
0.05 mm thick [surface tension of water is 70 × 10–3 N/m] :–
(A) 25 N (B) 20 N (C) 14 N (D) 28 N
21. A vessel, whose bottom has round holes with diameter of 0.1 mm, is filled with water. The maximum height to which
the water can be filled without leakage is :– (S.T. of water = 75 dyne/cm, g = 1000 cm/s2)
(A) 100 cm (B) 75 cm (C) 50 cm (D) 30 cm

22. A crown made of gold and copper weights 210 g in air and 198 g in water. The weight of gold in crown is:–[Given
: Density of gold = 19.3 g/cm3 and Density of copper = 8.5 g/cm3]
(A) 93 g (B) 100 g (C) 150 g (D) 193 g

23. To what height h should a cylindrical vessel of diameter d be filled with a liquid so that the total force on the vertical
surface of the vessel be equal to the force on the bottom :–
(A) h = d (B) h = 2d (C) h = 3d (D) h = d/2

24. Two vessels A and B have the same base area and contain water to the same height, but the mass of water in A
is four times that in B. The ratio of the liquid thrust at the base of A to that at the base of B is :–

(A) 4 : 1 (B) 2 : 1 (C) 1 : 1 (D) 16 : 1

25. Water stands upto a height h behind the vertical wall of a dam. What is the net horizontal force pushing the dam
down by the stream, if width of the dam is  ? (   density of water) :–

h 2 g h 2 g h g


(A) 2h g (B) (C) (D)
2 4 4

26. A U–tube is partially filled with water. Oil which does not mix with water is next poured into one side, until water
rises by 25 cm on the other side. If the density of the oil is 0.8 g/cc, the oil level will stand higher than the water
level by :–
(A) 6.25 cm (B) 12.50 cm (C) 18.75 cm (D) 25.00 cm

27. The side of glass aquarium is 1 m high and 2 m long. When the aquarium is filled to the top with water, what is
the total force against the side–
(A) 980 × 103 N (B) 9.8 × 103 N (C) 0.98 × 103 N (D) 0.098 × 103 N

28. The gauge pressure of 3 105 N/m2 must be maintained in the main water pipes of a city. How much work must
be done to pump 50,000 m3 of water at a pressure of 1.0  105 N/m2–
(A) 1011 J (B) 1010 J (C) 109 J (D) 108 J

29. The barometric pressure and height on the earth are 105 Pa and 760 mm respectively. If it is taken to moon, then
barometric height will be :–
(A) 76 mm (B) 126.6 mm (C) Zero (D) 760 mm

30. When a large bubble rises from the bottom of a lake to the surface, its radius doubles. If atmospheric pressure is
equal to that of column of water height H, then the depth of lake is :–
(A) H (B) 2H (C) 7H (D) 8H
31. A body floats in a liquid contained in a beaker. The whole system is shown in figure
falling under gravity. The upthrust on the body due to liquid is :–
(A) zero
(B) equal to weight of liquid displaced
(C) equal to weight of the body in air
(D) equal to the weight of the immersed body.

32. A boat having a length of 3 metre and breadth 2 metre is floating on a lake. The boat sinks by one cm when a man
gets on it. The mass of the man is
(A) 60 kg (B) 62 kg (C) 72 kg (D) 128 kg

33. A body of volume 100 c.c. is immersed completely in water contained in a jar. The weight of water and the jar before
immersion of the body was 700g wt. After immersion weight of water and jar will be
(A) 700 g wt (B) 800 g wt (C) 500 g wt (D) 100 g wt

34. The total weight of a piece of wood is 6 kg In the floating state in water its 1/3part remains inside the water. On
this floating solid, what maximum weight is to be put such that the whole of the piece of wood is to be drowned
in the water :–
(A) 12 kg (B) 10 kg (C) 14 kg (D) 15 kg

35. A sample of metal weights 210 grams in air, 180 grams in water and 120 grams in an unknown liquid. Then:–
(A) the density of metal is 3 g/cm3
(B) the density of metal is 7 g/cm3
(C) density of metal is 4 times the density of the unknown liquid
(D) the metal will float in water

36. A wooden cube first floats inside water when a 200 g mass is placed on it. When the mass is removed the cube
is 2 cm above water level. The side of cube is :–
(A) 5 cm (B) 10 cm (C) 15 cm (D) 20 cm

37. A piece of ice with a stone frozen in it on water is kept in a beaker. The level of water when ice completely melts–
(A) Increase (B) Decrease (C) Remain the same (D) None of these

38. A rectangular block is 5 cm 5cm  10 cm. The block is floating in water with 5 cm side vertical. If it floats with
10 cm side vertical, what change will occur in the level of water :–
(A) No change (B) It will rise
(C) It will fall (D) It may rise or fall depending on the density of block.

39. A wooden block of volume 1000 cm3 is suspended from a spring balance. Its weight is 12 N in air. It is suspended
in water such that half of the block is below the surface of water. The reading of spring balance is :–
(A) 10 N (B) 9 N (C) 8 N (D) 7 N
40. A boat carrying a number of large stones is floating in a water tank. What will happen to the water level if the stones
are unloaded into the water :–
(A) Rise (B) Fall
(C) Remain unchanged (D) Rise till half the number of stones are unloaded and then begin to fall

41. Streamline motion is that motion in which there is:–


(A) Only longitudinal velocity gradient (B) Only radial velocity gradient
(C) Longitudinal as well as radial velocity gradient (D) Neither longitudinal nor radial velocity gradient

42. An aeroplane of mass 3 × 104 kg and total wing area of 120 m2 is in a level flight at some height. The difference
in pressure between the upper and lower surfaces of its wings in kilo pascal is (g=10m/s2 ) :–
(A) 2.5 (B) 5.0 (C) 10.0 (D) 12.5
43. One end of a horizontal pipe is closed with the help of a valve and the reading of a barometer attached to the pipe
is 3 × 10 5 pascal. When the value in the pipe is opened then the reading of barometer falls to
105 pascal. The velocity of water flowing through the pipe will be in m/s :–
(A) 0.2 (B) 2 (C) 20 (D) 200

44. 16 cm3 of water flows per second through a capillary tube of radius a cm and of length  cm when connected to
a pressure head of h cm of water. If a tube of the same length and radius a/2 cm is connected to the same pressure
head, the quantity of water flowing through the tube per second will be:–
(A) 16 cm3 (B) 4cm3 (C) 1 cm3 (D) 8 cm3

45. A tank of height 5 m is full of water. There is a hole of cross sectional area 1 cm2 in its bottom. The initial volume
of water that will come out from this hole per second is :–
(A) 10–3 m3/s (B) 10–4 m3/s (C) 10 m3/s (D) 10–2 m3/s

46. In the figure below is shown the flow of liquid through a horizontal pipe. Three tubes A, B and C are connected
to the pipe. The radii of the tubes, A, B and C at the junction are respectively 2 cm, 1 cm. and 2 cm. It can be said
that the :–

A C
B

(A) Height of the liquid in the tube A is maximum


(B) Height of the liquid in the tubes A and B is the same
(C) Height of the liquid in all the three tubes is the same
(D) Height of the liquid in the tubes A and C is the same

47. The diagram (figure) shows a venturimeter, through which water is flowing. The speed of water at X is 2 cm/
s. The speed of water at Y (taking g = 1000 cm/s2) is :–

5.1mm

x
y

(A) 23 cm/s (B) 32 cm/s (C) 101 cm/s (D) 1024 cm/s

48. Water contained in a tank flows through an orifice of a diameter 2 cm, under a constant pressure difference of 10
cm of water column. The rate of flow of water through the orifice is:–
(A) 44 cc/s (B) 4.4 cc/s (C) 444 cc/s (D) 4400 cc/s
49. More viscous oil is used in summer than in winter in motors due to :–
(A) Rise in temperature in summer, the viscosity of oil decreases
(B) Rise in temperature in summer, viscosity of oil increases
(C) Surface tension of oil increases
(D) Surface tension of oil decreases
50. With increase in temperature, the viscosity of :–
(A) Gases decreases and liquid increases (B) Gases increases and liquid decreases
(C) Both gases and liquid increases (D) Both gases and liquid decreases
51. A rain drop of radius 0.3 mm has a terminal velocity in air 1m/s. The viscosity of air is 18 × 10–5 poise. The viscous
force on it is :–
(A) 101.73 × 10–4 dyne (B) 101.73 × 10–5 dyne
–5
(C) 16.95 × 10 dyne (D) 16.95 × 10–4 dyne
52. Two liquids of densities d1 and d2 are flowing in identical capillaries under same pressure difference. If t1 and t2
are the time taken for the flow of equal quantities of liquids, then the ratio of coefficients of viscosities of liquids
must be :–

d1 d 2 d1 t1 d1 t 2  d 1 t1 
(A) t t (B) d t (C) d t (D)  d t 
1 2 2 2 2 1 2 2

53. The velocity of falling rain drop attain limited value because of :–
(A) Surface tension (B) Upthrust due to air
(C) Viscous force exerted by air (D) Air current

54. The rate of flow of liquid through a capillary tube, in an experiment to determine the viscosity of the liquid, increases
:–
(A) When the pressure of the tube is increased (B) When the length of the tube is increased
(C) When the radius of the tube is decreased (D) None of the above

55. A copper ball of radius 'r' travels with a uniform speed 'v' in a viscous fluid. If the ball is changed with another
ball of radius '2r', then new uniform speed will be :–
(A) v (B) 2v (C) 4v (D) 8v

56. Two drops of equal radius are falling through air with a steady velocity of 5cm/sec. If the two drops coalesce, then
its terminal velocity will be :–
1 1 1 2
(A) 4 3  5 cm / s (B) 4 3 cm/s (C) 5 3  4 cm / s (D) 4 3  5 cm / s

You might also like