P/N:0000000000

UT673A/UT675A Battery Tester Tests below are based on 12V, 60Ah, CCA580A:
Overview 1. Battery test
UT673A/UT675A battery tester, with its leading-edge conductivity test technology, UT673A

accurately and rapidly helps users to measure the cold cranking amps capability of the Charge
Battery Crank
vehicle starting battery, healthy state of the battery itself, detect the common fault of
vehicle starting and charging system, which helps repair vehicle quickly. Data Setting About

UT675A
Safety information
Battery Charge
Please carefully read this manual and follow the warning and safety information before Crank

use. Data Print Setting

To avoid fire and overcurrent, please read all rated values and symbol descriptions
1. Make sure engine is off. 2. Connect to the correct polarity. 3. Select “Battery”
before use.
Do not open the case cover. Do not turn on the tester if its cover or front panel is open.
Do not touch the connectors and components if the tester is powered on. SET RATING

STANDARD
NORMAL BAT. CCA
Please contact the authorized repair personnel to detect, repair, maintain the tester AGM BATTERY DIN
TYPE 580 A
if you find any fault on it. EFB BATTERY JIS
Do not use in humid, explosive or inflammable environment. GEL BATTERY CCA
EN
Keep the tester surface clean and dry. Keep it well-ventilated.
4. Select “NORMAL BAT” 5. Select standard,CCA for example. 6. Set rated capacity of battery.
Product introduction UT673A
Interface TESTING GOOD BATTERY
SOH 75% 495A
UT673A Battery Charge
Crank SOC 100% 12.8V
1) Battery: Battery test.
2) Crank: Vehicle Cranking system test. R= 3.35mΩ
3) Charge: Vehicle Charging system test. Data Setting About
7. Press ENTER to start the test. 8. Display test result.
4) Data: The last test result can be viewed.
5) Setting: Language setting.
6) About: View the system information. UT675A Battery Test results

UT675A Description Interpretation

1) Battery: Battery test. The battery is in The performance of storage battery is good,
Battery Crank Charge
2) Crank: Vehicle Cranking system test. good condition. please continue using the battery.
3) Charge: Vehicle Charging system test.
The battery is in Because the voltage of storage battery is lower
4) Data: The last test result can be viewed or upload. Data Print Setting than 12.3V, so the performance of storage
5) Print: Print test data. good condition,
please charge battery is good, please continue using the
6) Setting: Language and time setting, view the system information. storage battery after it is fully charged.
the battery.
Feature Because the battery voltage is lower than 12V, so please
1) Applicable to 12V battery testing and 12V/24V vehicle cranking/charging system test. retest after it is fully charged. Incorrect reading may occur
Retest after charging
2) Measurement standard and range: if the battery is not fully charged. Please replace the battery
if “Retest after charging” displays again after charging.
Measurement Measurement Measurement Measurement
standard range standard range Replace the battery Replace the storage battery.

CCA 100-2000 DIN 100-1400 The battery is in bad

condition, replace Battery inside is damaged, replace the storage battery.
BCI 100-2000 IEC 100-1400 the battery.
CA 100-2000 EN 100-2000
1) Battery capacity (SOC): The percentage of remaining battery capacity,
MCA 100-2000 SAE 100-2000 Remaining capacity
SOC= Actual capacity ×100%.
JIS 26A17—245H52 Ah 30-200Ah
3) Working temperature: -20°C—50°C. 2) Battery voltage (VOLTAGE): The voltage value of storage battery (Unit: V).
3) Battery life (SOH): State of health of battery storage,
4) Special test clip: Double-conductor Kelvin clip.
5) Case material: Acid-resistant ABS plastic. Actual capacity
SOH= ×100%.
6) Measurement range of battery: 30Ah—200Ah. Nominal capacity
7) Measurement range of voltage: 7V—16V. 4) The measured cold-start current: The measured cold-start current of tester.
8) Portable. 5) Nominal cold-start current: Nominal cold-start current of storage battery
6) Internal resistance of battery (R): The measured internal resistance of storage battery.
Example for selecting standard
Battery NOTE: For low-capacity battery (For example, the vehicle is shut down for a long
Battery identification Standard parameter Remark time, the battery is not charged in time, the battery power is significantly lost
because the vehicle door is not closed.), the tester may prompt you to “Replace
12V/60Ah/CCA 500A CCA 500 12V battery, the capacity is 60Ah, battery” during actual measurement, please consult the storage battery factory
the cold-start current is 500A. and charge the battery according to the designated method, and then retest.
300A EN EN 300 The standard value is 300A.
2. Cranking test
12V battery, the capacity is 60Ah,
12V 250Ah 60Ah DIN DIN 250A
the standard value is 250A. UT673A

12V battery, the capacity is 60Ah, Battery Crank Charge

check JIS CODE conversion table

26A19R 12V 60Ah JIS# 200 Data Setting About
and find that 26A19R corresponds
UT675A
to 220A for CCA.
Battery Crank Charge
12V battery, the capacity is 60Ah,
check JIS CODE conversion table Data Print Setting
26A19RMF 12V 60Ah JIS# 220 and find that 26A19R corresponds 1. Make sure engine is off. 2. Connect to the correct polarity. 3. Select “Crank”
to 220A for MF CCA.
CRANKING TEST CRANKING TEST
If the standard is not found,
12V/60Ah AH 60Ah estimate CCA value according to START ENGINE RPM DETECTED
the battery capacity.

Operation instruction
4. Enter the interfaceof 5. Start engine. 6. Engine RPM is detected.
1. Connect the red and black clips of tester to the measured battery, red is positive, starting engine.
black is negative, the tester screen will display startup interface. If the battery voltage
is lower than 7.0V, the test will become abnormal. TESTING CRANKING NORMAL
2. According to the prompts, press up and down button to select: CRANKING 11.34V
UT673A: ① Battery test, ② Cranking test, ③ Charging test, ④ View test results, TIME 243ms
⑤ System setting, ⑥ About.
UT675A: ① Battery test, ② Cranking test, ③ Charging test, ④ View test results,
7. Automatically enter the test. 8. Display test result.
⑤ Print test result, ⑥ Setting.
Test results b. Press up or down button to adjust Month, then press ENTER to confirm this adjustment
and enter date adjustment.
Decision Interpretation c. Press up or down button to adjust DATE, then press ENTER to confirm this adjustment
Starting voltage is normal. The starting voltage is higher than 9.6V. and enter hour adjustment.
d. Press up or down button to adjust HOUR, then press ENTER to confirm this adjustment
Starting voltage is low. The starting voltage is lower than 9.6V.
and minute adjustment.
e. Press up or down button to adjust MINUTE, then press ENTER until “OK” is displayed.
3. Charging test After finishing the adjustment, the tester will go back to main interface. When adjusting
the time, the time character will flash. By pressing and holding the button, the character
UT673A will increase or decrease continuously.
Battery Crank Charge NOTE: Make sure the button is pressed for more than one second when adjusting time.
After entering time setting, pressing return button is disabled because the system time
Setting About
Data is protected, users need to set Year/Month/Day/Hour/Minute or press return button 5
UT675A
times to return.
Battery Crank Charge

Setting
Specification
Data Print

1. Make sure engine is off. 2. Connect to the correct polarity. 3. Select “Charge” Model UT673A UT675A
Applicable battery 12V cranking lead acid battery
CHARGING TEST RIPPLE TEST Ordinary lead acid battery, AGM flat plate battery,
START ENGINE Battery type
AGM spiral battery, GEL battery, EFB battery.
PRESS ENTER TO
5mV 12.65V
Battery capacity 3~250AH
CONTINUE

Battery standard CCA:40~2000; BCI:40~2000; CA:40~2000; MCA:

4. Enter the interface
of starting engine. 5. Start engine. 6. Start ripple test. 40~2000; JIS:26A17~245H52; DIN:40~1400; IEC:
and range
40~1400; EN:40~2000;SAE:40~2000; AH:3~250 AH
LOADED TESTING INCREASE RPM TO CHARGING NORMAL
Voltage range 7~16V DC
2500 R/MIN AND LOADED 14.26V
*** KEEP IT 5 SECONDS
PRESS ENTER TO
UNLOADED
RIPPLE
12.65V
5mV
Test method
AH rapid measurement
Four-terminal kelvin test lead

Overvoltage protection
8. According to the prompt, Step
on accelerator to increase the
7. Start loaded testing
engine speed to 2500 R/Min and
9. Display test result. Prevent counter voltage
hold for 5 seconds.
A prompt of poor contact

Test results: Internal resistance measurement

Battery life
Decision Interpretation
Remaining battery capacity
Charging system is normal, the output
Charging voltage is normal. Cranking test 12/24V cranking system test
voltage of engine is 13.5V~14.7V.
Charging test 12/24V charging system test
Charging system is under-voltage,
Charging voltage is low.
the voltage is lower than 13.5V. USB data transfer /
The voltage of charging system is higher Printing function /
Charging voltage is high.
than that of vehicle voltage stabilizer. LCD LCD (128*64 black and white lattice)
Generator voltage output is not detected. Language Chinese and English
No voltage output.
Check if the connector and generator belt is normal.
General
Test via current waveform, for example, the diode is
Diode test. Temperature 0°C~50°C
damaged due to high ripple voltage of diode.
Working
environment Relative Operating: below +35°C, ≤90%
View test result humidity Non-operating: +35°C~+40°C, ≤60%
a) For UT673A, ENTER to view the last test result of Battery test, Cranking and Net weight 264g 413g
Charging system test. (excluding batteries)
b) For UT675A, ENTER to view and export the last test result of Battery test, Cranking Product dimension
(excluding test leads) 76mm*22mm*142mm 95mm*47mm*183mm
and Charging system test. Connect the computer to export the last test result via
serial port and print the result. Packing box dimension 175mm*45mm*320mm 285mm*90mm*230mm
Note: Please find the application software on our website by searching UT675A and
search under Docs & Software section.
https://www.uni-trend.com.cn/index.php?m=content&
Accessories
c=index&a=show&catid=515&id=882 UT673A UT675A
Tester host: 1 piece Tester host: 1 piece
User manual: 1 piece User manual: 1 piece
Velcro strap: 1 piece USB cable: 1 piece
Printing paper: 3 pieces
About (Applicable to UT673A) Cloth bag: 1 piece
ENTER to view system information.
Print test result (Applicable to UT675A)
ENTER to print the last test result of Battery test, Cranking and Charging system test. Maintenance
Note: The normal working voltage of the printer is 10~16V. 1. Do not put or store the tester in the place where its LCD is exposed to direct sunlight
for a long time. No sprays, liquids or solvents are allowed on the tester or fixtures.
Setting 2. Please clean the dust on the tester with soft cloth. Do not scratch the protection
ENTER to select language (English or Chinese). screen of LCD. Wipe the tester with a damp but non-dripping soft cloth. Never use
any corrosive chemical detergents.
Function
ENTER to enter setting page. Warning: Before the tester is powered on, please make sure it is completely dry to
avoid short circuit caused by moisture.
Language selection
User can select desired language as needed. After entering language selection page,
press ENTER to select English or Chinese.
Time adjustment (Applicable to UT675A)
User can adjust or correct the system time, time sequence adjustment (Year/Month/Day
/Hour/Minute) does not affect the setting of date and time format.
a. Press up or down button to adjust the last two digits of the YEAR, then press ENTER
to confirm this adjustment and enter month adjustment.