INTERNATIONAL ISO

STANDARD 5752

Third edition
2021-06

Metal valves for use in flanged pipe

systems — Face-to-face and centre-to-
face dimensions
Appareils de robinetterie métalliques utilisés dans les tuyauteries à
brides — Dimensions face-à-face et face-à-axe

iTeh STANDARD PREVIEW

(standards.iteh.ai)
ISO 5752:2021
https://standards.iteh.ai/catalog/standards/sist/26fe0ef8-5318-449c-a04f-
229848df05b8/iso-5752-2021

Reference number
ISO 5752:2021(E)

© ISO 2021
ISO 5752:2021(E)

iTeh STANDARD PREVIEW

(standards.iteh.ai)
ISO 5752:2021
https://standards.iteh.ai/catalog/standards/sist/26fe0ef8-5318-449c-a04f-
229848df05b8/iso-5752-2021

COPYRIGHT PROTECTED DOCUMENT

© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: [email protected]
Website: www.iso.org
Published in Switzerland

ii © ISO 2021 – All rights reserved

 ISO 5752:2021(E)

Contents Page

Foreword ........................................................................................................................................................................................................................................ iv
Introduction..................................................................................................................................................................................................................................v
1 Scope ................................................................................................................................................................................................................................. 1
2 Normative references ...................................................................................................................................................................................... 1
3 Terms and definitions ..................................................................................................................................................................................... 1
4 Dimensions and tolerances ....................................................................................................................................................................... 2
Annex A (normative) Additional length for valves with ring joint flange ...................................................................27
Annex B (informative) Relationship between DN and NPS.........................................................................................................29
Annex C (informative) Origin of basic series.............................................................................................................................................30
Bibliography ............................................................................................................................................................................................................................. 34

iTeh STANDARD PREVIEW

(standards.iteh.ai)
ISO 5752:2021
https://standards.iteh.ai/catalog/standards/sist/26fe0ef8-5318-449c-a04f-
229848df05b8/iso-5752-2021

© ISO 2021 – All rights reserved iii

ISO 5752:2021(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
iTeh STANDARD PREVIEW
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/
iso/foreword.html. (standards.iteh.ai)
This document was prepared by Technical Committee ISO/TC 153, Valves.
ISO 5752:2021
This third edition cancels and replaces the second edition (ISO 5752:1982), which has been technically
https://standards.iteh.ai/catalog/standards/sist/26fe0ef8-5318-449c-a04f-
revised. 229848df05b8/iso-5752-2021
The main changes compared to the previous edition are as follows:
— extension to PN 63; PN 100; PN 160; PN 250; PN 320; PN 400; deletion of PN 1; PN 1,6; PN 4;
— extension to Class 900; Class 1 500; Class 2 500;
— addition of DN 1 050; deletion of DN 550;
— deletion of Table 1 (Isobaric) and Table 10 (copper alloy);
— update of the basic series in Table 1;
— update of the face-to-face and centre-to-face dimensions in Tables 2 to 19;
— addition of an informative Annex B giving the relationship between DN and NPS;
— addition of an informative Annex C giving the origin of each basic series.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.

iv © ISO 2021 – All rights reserved

 ISO 5752:2021(E)

Introduction
The aim of this document is to establish face-to-face and centre-to-face dimensions for metal valves
to permit a degree of dimensional interchangeability. They are intended to be used in valve product
standards.
Although the tables of face-to-face dimensions in this document represent a considerable rationalization
of international practices, it has not been possible to reduce these to a single series of dimensions for
the various types of valves. Alternatives have been included. For convenience these have been called
short, medium and long, but these terms are not used in a descriptive sense.
The pressure/temperature ratings for the different types of valves are those to be specified for the type
of valves and materials used.
The principle of establishing dimensions in this document is that, first, there exists an ISO industrial
valve standard covering that product, in its size and pressure rating, and second, certain valve types
are of significant international demand and their use justifies inclusion in this document.

iTeh STANDARD PREVIEW

(standards.iteh.ai)
ISO 5752:2021
https://standards.iteh.ai/catalog/standards/sist/26fe0ef8-5318-449c-a04f-
229848df05b8/iso-5752-2021

© ISO 2021 – All rights reserved v

 iTeh STANDARD PREVIEW
(standards.iteh.ai)
ISO 5752:2021
https://standards.iteh.ai/catalog/standards/sist/26fe0ef8-5318-449c-a04f-
229848df05b8/iso-5752-2021
INTERNATIONAL STANDARD ISO 5752:2021(E)

Metal valves for use in flanged pipe systems — Face-to-face

and centre-to-face dimensions

1 Scope
This document specifies the basic series of face-to-face (FTF) and centre-to-face (CTF) dimensions for
two-way metal valves of the gate, globe, diaphragm, ball, plug, butterfly design types used as isolating
and check valves in flanged pipe systems. Each basic series of face-to-face and centre-to-face dimensions
can be used as required with flanges of mating dimensions conforming to the equivalent EN or ASME
flange series.
This document covers valves with the following PN, Class, DN and NPS values:
— PN 2,5; PN 6; PN 10; PN 16; PN 25; PN 40; PN 63; PN 100; PN 160; PN 250; PN 320; PN 400;
— Class 125; Class 150; Class 250; Class 300; Class 600; Class 900; Class 1 500; Class 2 500;
— DN 10; DN 15; DN 20; DN 25; DN 32; DN 40; DN 50; DN 65; DN 80; DN 100; DN 125; DN 150; DN 200;
DN 250; DN 300; DN 350; DN 400; DN 450; DN 500; DN 600; DN 650; DN 700; DN 750; DN 800;
DN 900; DN 1 000; DN 1 050; DN 1 200; DN 1 400; DN 1 600; DN 1 800; DN 2 000;
iTeh STANDARD PREVIEW
— corresponding to nominal sizes NPS: ⅜; ½; ¾; 1; 1 ¼; 1 ½; 2; 2 ½; 3; 4; 5; 6; 8; 10; 12; 14; 16; 18; 20;
24; 26; 28; 30; 32; 36; 40; 42; 48; 56; 64; 72; 80.
(standards.iteh.ai)
NOTE See Annex B for the relationship between DN and NPS.
ISO 5752:2021
https://standards.iteh.ai/catalog/standards/sist/26fe0ef8-5318-449c-a04f-
2 Normative references 229848df05b8/iso-5752-2021
There are no normative references in this document.

3 Terms and definitions

For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp
— IEC Electropedia: available at http://www.electropedia.org/
3.1
DN
NPS
nominal size
alphanumeric designation of size for components of a pipework system, which is used for reference
purposes, comprising the letters DN or NPS followed by a dimensionless number which is indirectly
related to the physical size, (in millimetres for DN and in inches for NPS), of the bore or outside diameter
of the end connections
Note 1 to entry: The number following DN or NPS does not represent a measurable value and is not used for
calculation purposes except where specified in a product standard.

[SOURCE: ISO 6708:1995, 2.1, modified — The terms "nominal size" and "NPS" have been added, "NPS"
has been integrated into the definition and the Note 2 to entry has been deleted.]

© ISO 2021 – All rights reserved 1

ISO 5752:2021(E)

3.2
PN
Class
nominal pressure
numerical designation relating to pressure that is a convenient rounded number for reference purposes,
and which comprises the letters “PN” or “Class” followed by the appropriate reference number
Note 1 to entry: It is intended that all equipment of the same nominal size (DN or NPS) (3.1) designated by the
same PN number or Class number shall have compatible mating dimensions.

Note 2 to entry: The maximum allowable pressure depends on materials, design and working temperature, and is
to be selected from the tables of pressure/temperature ratings given in the appropriate standards.

[SOURCE: ISO 7268:1983, Clause 2, modified — The terms "nominal pressure" and “Class” have been
added, and “Class” has been integrated into the definition.]
3.3
face-to-face dimension
FTF
<straight pattern valves> distance between the two planes perpendicular to the valve axis located at
the extremities of the body end ports
Note 1 to entry: Dimensions are expressed in millimetres.

Note 2 to entry: See Figures 1 to 5 and Figure A.1.

3.4
centre-to-face dimension
iTeh STANDARD PREVIEW
CTF (standards.iteh.ai)
<angle pattern valves> distance, between the plane located at the extremity of either body end port and
perpendicular to its axis and the other body end port axis
ISO 5752:2021
https://standards.iteh.ai/catalog/standards/sist/26fe0ef8-5318-449c-a04f-
Note 1 to entry: Dimensions are expressed in millimetres.
229848df05b8/iso-5752-2021
Note 2 to entry: See Figures 1 to 5 and Figure A.1.

4 Dimensions and tolerances

The basic series of FTF and CTF dimensions, expressed in millimetres, shall be as given in Table 1.
Table 1 is a summary of the dimensions in Tables 2 to 19 giving the origin of each series and should be
referred to when considering valve types not covered by this document. Each particular column does
not necessarily include all the values of the relevant basic series. See Annex C for information as to the
origin of each basic series.
Tables 17 and 18 cover butterfly check or wafer check valves which are retained in the piping by bolting
that spans the two adjacent flanges, however these valves may alternately be furnished with full end
flanges. Check valves shown as ‘long pattern’ shall be furnished with full end flanges only.
The face-to-face and centre-to-face dimensions, as appropriate for the types of valves covered by this
document, shall be in accordance with Tables 2 to 19, and the tolerances shall be in accordance with
Tables 20 and 21. Annex A includes additional information on face-to-face and centre-to-face dimensions
where ring joint facing is used and shall be followed.
Tolerances on FTF and CTF dimensions as shown in Figure 1 are given in Table 20. Both tolerances shall
be fulfilled.

2 © ISO 2021 – All rights reserved

 ISO 5752:2021(E)

Key
a face-to-face (FTF)
b centre-to-face (CTF)

Figure 1 — Face to face and centre to face dimensions

iTeh STANDARD PREVIEW

(standards.iteh.ai)
ISO 5752:2021
https://standards.iteh.ai/catalog/standards/sist/26fe0ef8-5318-449c-a04f-
229848df05b8/iso-5752-2021

a) flat face b) raised face

Key
a face-to-face (FTF)

Figure 2 — Flanged valves PN and Class designated (flat and raised faces)

© ISO 2021 – All rights reserved 3

ISO 5752:2021(E)

a) b) c) d) e) f)
Key
a face-to-face (FTF)

Figure 3 — Flanged valves PN designated (other types)

Class 150 and Class 300 Class 600 and above

iTeh STANDARD PREVIEW
(standards.iteh.ai)
ISO 5752:2021
https://standards.iteh.ai/catalog/standards/sist/26fe0ef8-5318-449c-a04f-
a) Large or small male face
229848df05b8/iso-5752-2021

b) Large or small female face

c) Large or small tongue

4 © ISO 2021 – All rights reserved

 ISO 5752:2021(E)

Class 150 and Class 300 Class 600 and above

d) Large or small groove

Key
a for dimensions, see Tables 2 to 19
b face-to-face (FTF)
c centre-to-face (CTF)
e height

NOTE For height e, see appropriate flange standard.

Figure 4 — Flanged valves Class designated (other types)

iTeh STANDARD PREVIEW

End flange seating surfaces shall be parallel or perpendicular. Tolerances “c” on parallel or perpendicular
surfaces as shown in Figure 5 are given in Table 21.
(standards.iteh.ai)
ISO 5752:2021
https://standards.iteh.ai/catalog/standards/sist/26fe0ef8-5318-449c-a04f-
229848df05b8/iso-5752-2021

Figure 5 — Tolerances on parallelism and perpendicularity

© ISO 2021 – All rights reserved 5

6
Table 1 — Dimensions of basic series (1-24)
Dimensions in millimetres
Nominal size Basic series DN
DN NPS 1 2 3 4 5 7 8a 9a 10 11a 12 13 14 15 16 17 18 19 20 21 24a
10 ⅜ 210 102 — — 105 102 51 — 115 — — – — — — — 10
15 ½ 210 165 105 57 — 115 — — — 15
ISO 5752:2021(E)

130 108 90 130 80

20 ¾ 150 117 152 117 115 117 — 120 — — 152 152 25 117 b 20
130 108 140 108 90 108 130 140 80 140 108 b 83

25 1 160 127 165 216 127 100 115 127 70 — 125 120 — 165 100 165 25 216 c 25
230 190 95 64 130 90 95

32 1¼ 260 76 165 — — 32
230 140 108

40 1½ 200 260 165 165 165 121 40

180 140 178 229 146 105 130 140 130 140 178 110 178 33 229 d 114

50 2 216 102 250 216 267 50

190 241 159 115 130 83 106 140 240 33 190 120 190 33 241 e

65 2½ 216 222 112 170 270 165 65

230 300 178 292 190 125 150 203 203 108 150 43 135 216 43 146

80 3 121 80
290 340 190 241 330 216 145 170 108 46 241 165 241 46 292

100 4 52 216 100

310 380 203 283 356 254 155 190 241 241 114 180 280 64 283 185 283 46 318 178

125 5 500 70 — 56 125

350 430 229 305 432 305 175 215 292 146 305 127 190 300 64 305 229 305 356

150 6 550 267 76 — 56 150

400 254 381 508 356 200 250 330 g 178 356 140 200 325 381 381 400 254

200 8 600 650 660 502 — 60 200

480 403 559 406 225 275 356 h 203 394 140 210 350 403 403 444 279

250 10 775 — 622 165 250 — 622 250

292 419 521 275 325 495 248 457 152 230 400 89 419 533 f 330

300 12 502 — 610 500 — 502 711 300

ISO 5752:2021
730 330 457 787 635 325 311 533 450 114 568 457 68 394

350 14 762 — — 550 127 762 — 572 — 350

850 900 356 838 749 375 698 349 178 270 114 648 78 419

229848df05b8/iso-5752-2021
400 16 — 762 600 — 610 102 — 400
980 1 025 381 889 425 787 394 686 190 290 78 838

450 18 — 500 — 650 152 — 660 — 450

(standards.iteh.ai)
1 100 1 150 406 838 991 475 575 864 i 457 216 310 140 838 864

500 20 — — 700 — 700 152 — 711 127 1 016 — 500

1 200 1 275 432 914 1 092 978 483 864 222 330 914 114 978

600 24 — — — — — — 600
1 250 1 400 457 991 1 194 978 914 229 350
iTeh STANDARD PREVIEW 991
1 450 1 650 508 1 143 1 397 1 295 1 067 267 390 800 178 1 143 787 154 1 346

https://standards.iteh.ai/catalog/standards/sist/26fe0ef8-5318-449c-a04f-
NOTE See informative Annex C for the origin of the basic series.
a CTF dimensions for angle pattern valves.
b For swing check valve only. For globe valve use152 for DN15 and 178 for DN20.
c For swing check valve only. For globe valve use 203.
d For swing check valve only. For globe valve use 216.
e For swing check valve only. For globe valve use 229.
f For swing check valve only. For globe valve use 559.
g For swing check valve only. For globe valve use 356.
h For swing check valve only. For globe valve use 406.

© ISO 2021 – All rights reserved

i For swing check valve only. For globe valve use 914.
 Table 1 (continued)
Nominal size Basic series DN
DN NPS 1 2 3 4 5 7 8a 9a 10 11a 12 13 14 15 16 17 18 19 20 21 24a
650 26 — — — — — — — — — — — — — — 650
700 28 1 650 — — — — — — — — 165 — 700
559 1 245 1 448 1 295 1 143 1 245 1 346

750 30 1 750 — — — — — — — — — — 750

610 1 346 1 549 1 448 292 430 900 229 1 346 1 499

800 32 — — — — 1 676 — — — — — 800

610 1 397 1 651 1 524 1 295 950 230 1 397 190 1 594

900 36 2 050 — — — — — — — — 900

© ISO 2021 – All rights reserved

1 850 660 1 524 1 778 318 470 1 000 241 1 524 190 1 778

1 000 40 2 250 — — — — — — — — — — — — 216 — — 1 000

711 1 727 2 083 1 956 1 600 330 510 1 100 241 1 727 203 2 083

1 050 42 — — — — — — — — — — — — — — — — — — — — — 1 050
813 410 550 1 200 300

1 200 48 — — — — — — — — — — — — — — — — — 1 200
1 400 56 — — — — — — — — — — — — — — — — — — 1 400
470 630 350 254

1 600 64 — — — — — — — — — — — — — — — — — — 1 600
530 710 390

1 800 72 — — — — — — — — — — — — — — — — — — 1 800
600 790 440

2 000 80 — — — — — — — — — — — — — — — — — — 2 000
670 870 490
760 950 540

ISO 5752:2021
NOTE See informative Annex C for the origin of the basic series.
a CTF dimensions for angle pattern valves.

229848df05b8/iso-5752-2021
b For swing check valve only. For globe valve use152 for DN15 and 178 for DN20.
c For swing check valve only. For globe valve use 203.

(standards.iteh.ai)
d For swing check valve only. For globe valve use 216.
e For swing check valve only. For globe valve use 229.
f For swing check valve only. For globe valve use 559.
g For swing check valve only. For globe valve use 356.
h For swing check valve only. For globe valve use 406.
iTeh STANDARD PREVIEW
i For swing check valve only. For globe valve use 914.

https://standards.iteh.ai/catalog/standards/sist/26fe0ef8-5318-449c-a04f-
ISO 5752:2021(E)