Digital Motor Protection Relay

REPM DIGITAL
Series Meta - MEC
 Digital
Motor Protection Relay
General digital type motor protection relays using MCU(Micro Controller Unit)
-Real time processing and high precision

Multiple protection
Protection DMP�-S DMP�-SZ DMP�-SI DMP�-SE DMP�-SEZ DMP�-SEI DMP�-T DMP�-TZ DMP�-TI DMP�-TE DMP�-TEZ DMP�-TEI
Wiring Screw type Tunnel type
Panel mount Unit type Extension type Unit type Extension type
Over current
Under current
Stsll
Lock
Phase failure
Revers phase
Asymmetry
Grount fault
Short circuit

Install the Unit /Extension type in one body

The display part may be seperated from the body
You can check the values and the causes of the
fauit without opening the distrioution panel door

�Fig. (D-EMPR in the MCC unit)

Both screw type and tunnel type

wirings are available in a DMP-E
Type D-EMPR
Simply detach the screw terminal, you can use it by
the tunnel type reiay

Standard: IEC60947-1, IEC60947-4-1, IEC60947-5-1,

UL508, KSC4504
Certification & approval: CE, UL, cUL, Lloyd register,
Korea legister, KS, ISO 14001,
ISO 9001(Including proceedings)
2
 M e t a - M E C S E R I E S

Display the causes of the fault and the values

Prompt A/S by looking the LED panel which
displays the causes of the fauit and the values

3phase digital ampere-meter function

(Digital ampere-meter)
Additional ampere-meter is not needed
Motor load rate(%)
Easy to check the motor
load condition

R phase current value S phase current value T phase current value

Selectable either the inverse time or definite time

characteristics

Defiinite time characteristics Inverse time characteristics

Applicable to the inverter contol circuit

LG DMPR has high performance under the
harmonic noise and can be used in the
Inverter control circuit (20~200Hz)

Elegant design
High class product image
by the elegant design

3
 Specifications of D-EMPR
Digital E M P R

DMP�-S DMP�-T DMP�-SE DMP�-TE

Model No. DMP06-S DMP60-S DMP06-T DMP60-T DMP06-SE DMP60-SE DMP06-TE DMP60-TE
Wiring Screw type Tunnel type Screw type Tunnel type
Panel mount Unit Extension(Note1)
Operation time Select either reverse time characteristics or definate time characteristics
Protection Over current According to the setting time
Phase failure 3 sec.
Reverse phase Within 0.1 sec.
Asymmetry 5 sec.
Stall 5 sec.
Lock Within 0.5 sec.
Under current 3 sec.
Ground fault Within 0.05~1 sec. Selectable (0.05~1.0sec)
Short circuit (Note2) Within 50ms
Alarm Variable (60~110% of the setting current)
Current setting range (A) 0.5�6 5�60 0.5�6 5�60 0.5�6 5�60 0.5�6 5�60
Motor capacity 220�240V 0.09�0.75 1.1�11 0.09�0.75 1.1�11 0.09�0.75 1.1�11 0.09�0.75 1.1�11
(kW) 380�440V 0.12�1.5 2.2�22 0.09�1.5 2.2�22 0.09�1.5 2.2�22 0.09�1.5 2.2�22
Time setting Definate Delay in starting 0�60sec
range (sec) time Delay in operating 0�30sec
Inverse time 0�60sec
Reset Manual reset
Tolerance Current ±5%
Time ±5%(or ±0.5sec)
Operating power (Note3) Voltage AC 190~250V
Frequency 60Hz (50Hz)
Aux. contact OL 2-SPST 3A/250Vac Resistive load
AL SPST 3A/250Vac Resistive load
Insulation resistance Over DC 500V 100㏁
Surge impulse voltage(IEC1000-4-5) 1.2×50㎲ 6kV (Apply standard wave form)
Fast transient burst(IEC1000-4-4) 2.5kV/5min
Environment Temperature Operation -25�70℃
Storage -30�80℃
Humidity 30�90% RH (No freezing)
Display 7-Segment 3 phase current, cause of a fault
Bar-Graph 60�110% of real load current
Mounting type 35mm Din-rail/Panel

Note1) In extension type, the digital EMPR is calibrated with combining the display past and mainbody so, please cautious not to
combine the display part and main body with different part No.
Note2) Instantaneous short circuit protection is optional
Note3) Operational voltage of AC 110V and 50Hz is optional

4
 Setting M e t a - M E C S E R I E S

Digital E M P R

Before operating a motor, set the D-EMPR as follows

1. C h e c k t h e o p e r a t i o n o f t h e T e s t / R e s e t b u t t o n R phase Digital display

� Check the operation when it is tripped S phase Bar graph

1) Check the wiring method (Refer to P13~14) T phase

2) Press the Test/Reset button and then test is Display button
displayed on the LED and the DMPR is tripped Test/Reset button

3) Press the Test/Reset button again and then

it is reset FUNC button Sel button
Note) In order to avoid the trip fault, the push
operation of Test/Reset is not avaiable Current knob Time knob
when a motor is rotating

2. Shift the mode by pressing the FUNC key and then select the values by press the Sel key
� You can finish the setting by pressing the Sel key in the Sto mode
� To protect the operation under the motor rotating, setting is allowed only in the test mode
FUNC Sel Functions Note
Inverse or definite time Default is inverse time
characteristics characteristics
Set the O-time For D-time setting,
(Definite time only) use the time knod
Reverse phasse protection Default is ”Off”

Under current protection Default is ”Off”Note1)

Alarm function Default is ”Off”

(With pre-alarm function)
Stall function Default is ”Off”

Lock function Default is ”Off”

Note2)
CT ratio Default is 1:1

Phase failure Default is ”On”

Store

Note1) Set the under current value from above 350mA

Note2) Do not change the CT ratio in 60 type (Dafault is 10:1)
1) Fist shift to the test mode by press the ”Test/Reset”button and then set the functions
by press the ”FUNC”button
2) Each time you press the ”FUNC”button, the function mode switches from 1.CHA mode to Sto mode.
When the mode that you want to change is displayed, push the ”Sel”button to select the value you want.
After you select the value, press the ”FUNC”button to finish the settings and it displays the next mode
3) If no button is pressed in the selection mode, it remains in that mode
4) If you select the inverse time characteristics it skips the mode 2 (Definite O-time) and go to the
mode 3 (Reverse phase)

5
 Setting
Digital E M P R

Alam signal (Alert function)

5) 5. Alt is the alert setting mode. It displays the load rate 5.A Lt AL(07-08) contact operation
of the current setting value by the bar LED (60~110%)
- If the current is higher than the setting value, the bar 1
LED is swieched on and off and the AL relay(07-08) make On
0
close and open in 1sec interval unitl the EMPR is tripped
(Pre-alarm function) 1
- If the 5. Alt mode is set to off, the AL relay make close 0
after the EMPR is tripped (Normal open contact) Off
6) To finish the settings you have to press the ”Sel”button Normal Alarm Trip
in the Sto mode Alert setting Trip setting
value value

3. Adijust the operating time by the time knod

▶ Inverse time characteristics

1) Select the inverse time in the 1. CHA mode, the default operating time is 600% of the rated current
2) The setting range of the operating time is 0~60sec. Set the time by considering the motor start time
3) When it is over the setting time, the EMPR operate in accord with the hot curve
▶ Definite time characteristics
1) Select the definite in the 1. CHA mode, it is operated by the definite time characteristics
2) D-time means the time that delays the operating time when the motor is starting
3) The setting range of the operating time is 0~60sec. Set the time by considering the motor start time
4) Set the O-time at the setting mode 2. dEF and the range is 0~30sec

4. Adjust the operating current by the current knob

1) Set the operating current based on the rated current that is discribed in the name plate.
Gennerally set the 110~115% of the real load current in the normal load condition
2) There ara 2 CT types according to the current range (0.6 / 60). When you use the external CT you can see
the real current by set the CT ratio (In 60CT type the defaut CT ration is 10:1)
3) You can easily set the current value by refer to the load rate which is displayed on the bar-graph
(Approx. 90% load rate)

6
 M e t a - M E C S E R I E S

5. Check the setting state by the display key

1) In normal condition it display the maximum
current among the three phase current
2) Each time you press the ”Display”button
you can see the current and values as PIG X
3) If no button is pressed for 3~4 seconds. it
returned to the normal condition R phase current

Set the O-time to 10sec S phase current

(Display only in definite time)

Normal condition

Set the D-time to 10sec T phase current

(Set the motor starting time)

5A setting

6. Check the causes of the fault by look at the display part

� The causes of the fault is switched on and off for 0.5sec interval. If you press the ”Display”button at this time,
display you can see the values and the causes of the fault

Turn on
Overload

ex)
Under current Reverse phase
Turn
on& off

Phase fail Ground fault

Stall Short circuit

Lock
7
 Dimensions
Digital E M P R

Type Dimensions Mounting dimensions

※Aux. contact wire size

:below 8［mm2］
※Torque : 0.5N

DMP�-S
DMP�-SZ

DMP�-SE
DMP�-SEZ

Panel mounting

Panel cutting size

8
 M e t a - M E C S E R I E S

Type Dimensions Mounting dimensions

※Wire size to penetrate a CT

:below 22［mm2］

DMP�-T
DMP�-TZ

DMP�-TE
DMP�-TEZ

Panel mounting

Panel cutting size

Note1) In extension type, the digital EMPR is calibrated with combining the display unit and mainbody
so, pleose cauyious not to combine the display unit and mainbody with different part No.
Note2)The 07-08 contacts ara the ZCT input terminal (Digital EMPR with ground fault function)
9
 DMP-S/SE/T/TE
Digital E M P R

DMP-S/SE/ T / TE
Over-current/Under current/Phase failure/Asymmetry
Stall/Lock/Instantaneous short circuit protection
�Unit type or extension type is available
- Extension type:Remotely mounts the display unit
on the panel surface
�3 phase ampere meter function:Check the 3 phase
current and setting value by press the display button
�Select the inverse time or definite time
�Easy to operate:Set the most function by the operation
button and knod
�Display the causes of the fault and the values
�Alarm setting:Load ratio is displayed up to setting current
�Instantaneous current function is option

Protect function
Over current Depend on setting time Selectable the inverse/definite
Phase loss Within 3seconds Over 70% of the rate of unbalance
Phase unbalance Within 5seconds Over 50% of the rate of unbalance
Phase reverse Within 0.1seconds Function enable
Stall Within 5seconds Over 180% of the setting current
Lock Within 0.5seconds Setting 200~900% of rated current
Under current Within 3seconds Setting 30~70% of rated current
Instantaneous current (Note1) Within 50seconds Setting 300~1800% of rated current
☞ Lock protection is operated after setting D-time in case of definite time type

Function selection
FUNC Sel Description
1. CHA Inv/dEF Operating characteristics setting(Inverse/definite time type)
2. dEF 0�30(S) Setting the operating time(In definite type)
3. r.P oFF/on Phase reverse enable
4. Und oFF/30�70(%) Under current enable and setting
5 . A lt oFF/60�110(%) Alerting enable and setting
6. S t l oFF/on Stall enable
7. Loc oFF/200�900(%) Lock enable and setting
8. Ct 1�120 CT ratio setting
9. P.F on/oFF Phase fault enable
Sto Sto Store
☞ 2.dEF is only displayed when dEF is selected in a 1.CHA mode

Ratings
Model D M P � -S DMP � -SE D M P � -T DMP �-TE
Type Wiring method Screw Tunnel
Panel mount Unit Extension Unit Extension
Operating characteristics Inverse/definite type
Alerting function Variable between 60 and 110%
Current range(A) DMP06-� 0.5�6
DMP60-� 5~60
Setting time Definite Delay(D-T) 0�60seconds
Operating(O-T) 0�30seconds
Inverse 0�60seconds
Reset type Manual reset
Operating voltage Voltage AC 190~250V
Frequency 60Hz (50Hz)
Aux. contacts OL 2-SPST(95~98) 3A/250Vac resistive load
AL SPST(07-08) 3A/250Vac resistive load
Indicate 7-segment 3-phase current value, fault cause
Bar-LED arrys Load ratio (60~110%)
Mounting 35mm Din-rail/Panel
10 Note) Instantaneous current protection function is option
 M e t a - M E C S E R I E S

Wiring method 1 Phase motorNote2)

Operational
power

Note1)

External CT combination

Note1) In is more effective to install the lead-phase capacitor close to a motor in the load side than to install in the line side
11
Note2) Please turn off the reverse phase function when it is used for 1 phase motor
 DMP-SZ/SEZ/TZ/TEZ
Digital E M P R

DMP-SZ/SEZ/ TZ/ TEZ

Over-current/Under current/Phase failure/Asymmetry
Stall/Lock/Ground-fault
�Unit type or extension type is available
- Extension type:Remotely mounts the display unit
on the panel surface
�3 phase ampere meter function:Check the 3 phase
current and setting value by press the display button
�Select the inverse time or definite time
�Easy to operate:Set the most function by the operation
button and knod
�Display the causes of the fault and the values
�Ground fault protect function is added

Protect function
Over current Depend on setting time Selectable the inverse/definite
Phase loss Within 3seconds Over 70% of the rate of unbalance
Phase unbalance Within 5seconds Over 50% of the rate of unbalance
Phase reverse Within 0.1seconds Function enable
Stall Within 5seconds Over 180% of the setting current
Lock Within 0.5seconds Setting 200~900% of rated current
Under current Within 3seconds Setting 30~70% of rated current
G r o u n d f a u l t (Note1)
Selectable Grounded current setting by dip s/w
0.05~1.0seconds (100~2500mA)
☞ Lock protection is operated after setting D-time in case of definite time type

Function selection
FUNC Sel Description
1. CHA Inv/dEF Operating characteristics setting(Inverse/definite time type)
2. dEF 0�30(S) Setting the operating time(In definite type)
3. r.P oFF/on Phase reverse enable
4. Und oFF/30�70(%) Under current enable and setting
5. g-F oFF/0.05�1.0(S) Ground fault enable and setting
6. S t l oFF/on Stall enable
7. Loc oFF/200�900(%) Lock enable and setting
8. Ct 1�120 CT ratio setting
9. P.F on/oFF Phase fault enable
Sto Sto Store
☞ 2.dEF is only displayed when dEF is selected in a 1.CHA mode ※ 2.dEF : Refer to page 10
☞ Ground fault sensitive current selection : Refer to page 15

Ratings
Model DMP� -SZ DMP� -SEZ DMP �- T Z DMP� -TEZ
Type Wiring method Screw Tunnel
Panel mount Unit Extension Unit Extension
Operating characteristics Inverse/definite type
Alerting function Variable between 60 and 110%
Current range(A) DMP06-� 0.5�6
DMP60-� 5~60
Setting time Definite Delay(D-T) 0�60seconds
Operating(O-T) 0�30seconds
Inverse 0�60seconds
Reset type Manual reset
Operating voltage voltage AC 190~250V
Frequency 60Hz (50Hz)
ZCT input (07-08) 200mA/110mV
Aux. contacts OL 2-SPST(95~98) 3A/250Vac resistive load
AL SPST(07-08) 3A/250Vac resistive load
Indicate 7-segment 3-phase current value, fault cause
Bar-LED arrays Load ratio (60~110%)
Mounting 35mm Din-rail/Panel
12
 M e t a - M E C S E R I E S

Wiring method

External CT combination

13
 Characteristics curve
Digital E M P R

Definite time characteristics

14
 Ordering M e t a - M E C S E R I E S

Digital E M P R

DMP06 - SEZ 220

Current setting range Wiring method Type Option Operational power

06 0.5~6A S Screw - Unit Z Ground fault 220 AC220V
60 5~60A T Tunnel E Extension I Short circuit 110 AC110V

�The standard length of a extension cable is 1m,

2m, 4m cable is optional
�For ground fault protection, ZCT (30�,50�,65�,80�)made by
LG is optionally required

1) Detach the screw terminal

Remove the 3 screws either in the line side or

the load side and pull out the bus bsr.
If you remove the screw terminal, you can
use it as a tunnel type digital EMPR,
assemble it to the opposite sequence

2) Select the ground fault sensitive current

Sensitive current Dip s/w

(mA) 1 2 3 4
100 � � � �
200 1 � � �
500 � 1 � �
1000 � � 1 �
1500 � � � 1
2000 � � 1 1
2500 1 1 1 1

Note) High sensitive current(30~300mA)

is optional

15
 2001-11

LG constantly endeavors to improve � HEAD OFFICE

the products, so that information in LG Twin Towers W19F, 20, Yoido-Dong, Youngdungpo-gu,
this catalog is subject to be changed
Seoul 150-721, Korea
without prior notice.
Tel:(82)2-3777-4900~4910 Fax:(82)2-3777-4879
� http://www.lgis.com

DMPR 2001 / Nov. 2001 Printed in Korea STAFF