www.middleeast.

weber

weberoof SPF
Waterproofing & thermal insulation roofing system

THERMAL IMPERMEABILITY SOLAR

INSULATION REFLECTANCE
 ROOFING SYSTEM COMPARISON
weberdry 116 FX-SP (White)

weberoof SPF INVERTED ROOF BUILT UP SINGLE-PLY MEMBRANE

weber jointseal PU MC (IRMA)

What is
Energy & • Lower roof temperatures • Indoor comfort and environment more • Indoor comfort and environment
sustainability • Lower heating and cooling costs difficult to achieve more difficult to achieve
• No thermal bridges • Loss of thermal insulating properties • Build-up temperature

weberoof SPF?
• Highest R-value insulation with age as the insulation is not • Thermal bridges
• Reflects solar radiation completely covered and protected
• Improve individual comfort from exposure to water and
weberfloor rapid environmental conditions
• Thermal bridges
It is a fully bonded long-lasting weberdry roof
roofing system, combining high weber filler board PE Weather • Closed cell foam which resists • Joints and seams can allow water • Lots of seams
energy performance and low impact water penetration migration • Frequent ponding
maintenance cost, to insulate and Geotextile white PP • High wind uplift resistance • Drain design is difficult and impact • Leaks difficult to locate
waterproof flat and low slope roofs. weberdry SPF 45
waterproofing property of system • Drain and slope design is difficult
and impact waterproofing property
of system

Concrete slab

Installation • Fast installation • Costly • Not conforms to irregular

• Lower labor cost • More labor needed substrate shapes
The weberoof SPF is built up of different layers combined to form a perfect roofing system, that consists of • Fully adhere to many different • Not conforms to irregular substrate • Seams and terminations are
a two-component spray applied polyurethane foam weberdry SPF 45, protected with a UV resistant substrates shapes potential leakage points
protective coating weberdry roof, followed by a filter layer of Geotextile white PP, covered with screed to slope • Self flashing system • Lots of terminations and flashings
• Fully mechanized installation
BOB

weberfloor rapid casted in bays using weber filer board PE, finally covered and protected by a cement based procedures
acrylic coating weberdry 116 FX-SP white with a solar reflective index value SRI> 78.
The multi-layer system provides waterproofing, thermal insulation and finishing in one solution.
Repair & • Low maintenance • Difficult to inspect and repair • Difficult to inspect and repair
maintenance • Multiple recoating at intervals • Costly
NO. MATERIAL MATERIAL DESCRIPTION possible

Two-component spray applied polyurethane foam to produce rigid foam with closed cells,
1 weberdry SPF 45
density 44-48 kg/m3

2 weberdry roof Mono component acrylic based waterproof coating for roof

3 Geotextile white PP Polypropylene geotextile 125 g/m2

4 weberfloor rapid Rapid drying, shrinkage controlled semi-dry floor screed

5 weber filler board PE Polyethylene filler board

6 weber jointseal PU MC One component polyurethane sealant and adhesive

7 weberdry 116 FX-SP (White) Two-component flexible cement based acrylic waterproof coating

THERMAL CONDUCTIVITY & U-VALUE

The building’s roof components have different thermal properties that interact together to define the heat
transfer with the external environment. One of these properties is the thermal conductivity, also called
lambda (W/m.K), which defines the heat transmitted in a unit time through a unit thickness of the material.
A low thermal conductivity indicates a good thermal insulating material.
A thermal insulating system is characterized by its thermal transmittance or U-value.

Benefits
MATERIAL λ: THERMAL COND. THICKNESS R: THERMAL RESISTANCE
(W/m K) (mm) (m2K/W)

RSe (exterior surface thermal resistance) 0.0380

Quick and easy insulated, waterproofed roof
weberdry 116 FX-SP (White) 0.190 1.2 0.0063 Insulating properties meeting local and international green building requirements
weberfloor rapid 1.400 70.0 0.0500 Joint free thermal insulation and waterproofing system
Single submittal and approval for the entire system
weberdry roof 0.190 1.2 0.0063
Fully bonded multilayer waterproofing
weberdry SPF 0.025 170.0 6.8000 Roof tiles not required
Reinforced concrete 1.900 150.0 0.0789 Lower energy consumption due to better insulation
Low maintenance & easy repair
RSi (interior surface thermal resistance) 0.2058
Topcoat EPD certified in accordance with EN 15804 and ISO 14025
7.1854
Total Total 392.4 Topcoat with an SRI > 78 to prevent heat island effect on roof
(Inc. external and internal resistance)
Quality controlled application of the system through authorized applicators certified by DCL
U-value 0.14 W/m2K
SAINT-GOBAIN UNITED ARAB EMIRATES
Masdar City
P.O. Box 96082
Abu Dhabi
United Arab Emirates
www.saint-gobain-emme.com Saint-Gobain
UAE