Scribd
Upload
33 views6 pages

Implement Pump - Assemble (UENR1353)

Uploaded by

Mahmoud Samer
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
33 views6 pages

Implement Pump - Assemble (UENR1353)

Uploaded by

Mahmoud Samer
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

Implement Pump - Assemble (UENR1353)

SMCS - 5084 i04397961

Assembly Procedure
PIP
Table 1
Required Tools
-
202 1018
Tool Part Number Description 4
05: 07/0 735
Qty
/ 1
A 1P-0510 Driver Group
3 1

UE 1:12+ 8
1. Inspect the O-ring seals for wear and for damage. Replace the components with new components,

N
© 2 R13 03:00
if necessary. Make sure that the components are clean. Apply clean oil to the surfaces of the
components during assembly.

024 53
Note: The internal components of the piston pump are machined to fine tolerances. Take care to

Cat
protect the surfaces of these components during the maintenance procedure.

erp
illa
rI nc.

Illustration 1 g00710299

2. Install screws (40) and install bearings (41). Apply 7M-7456 Bearing Mount Compound to the
screws. Tighten the screws to a torque of 4 ± 0.4 N·m (35 ± 4 lb in).

3. Install two seals (39), two retaining rings, and bearing cup (38) in the housing.

Illustration 2 g00710298
4. Raise the temperature of bearing (36) to 135 °C (275 °F) and install the bearing on shaft (34).

5. Install two stops (37) on swashplate (35).

6. Install shaft (34) in the housing.

7. Install swashplate (35) in the housing.

Illustration 3 g00686177

Illustration 4 g00686179

Personal injury can result from being struck by parts propelled


by a released spring force.

Make sure to wear all necessary protective equipment.

Follow the recommended procedure and use all recommended


tooling to release the spring force.

8. Use Tooling (A) and a suitable press in order to assemble barrel (27). Compress spring (31) until
Tooling (A) is below the groove for retaining ring (33). Install the retaining ring and slowly release
the compression on the spring.
Illustration 5 g00686175
9. Install nine pistons (28) and slipper retainer (29) in the barrel in the original locations.

10. Install barrel (27), pistons (28), and slipper retainer (29) as a unit in the housing.

Illustration 6 g00630341

11. Install bearing (25) and spacer (26) in each side.

12. Install two allen head screws (24) in each side. Tighten the screws to a torque of 33 ± 3 N·m
(24 ± 2 lb ft).

Illustration 7 g00686104

13. Install plug (22) and O-ring seal (23) in the pump housing.
Illustration 8 g00630342
14. Install O-ring seal (21) on the cover.

15. Install three screws (19) and cover (20) on the pump housing. Tighten the screws to a torque of
8.5 ± 1 N·m (75 ± 9 lb in).

Illustration 9 g02576457

16. Install valve plate (13), shims (12), and bearing cone (11). Use shims in order to obtain end play of
0.010 mm to .100 mm (0.0004 inch to .0040 inch).

17. Install a new gasket (17) and pins (14) on the face of the housing.

18. Install piston (15) in the implement pump.

19. Install bias piston (16) and spring (18) in the implement pump.

Illustration 10 g02576456
20. Install the O-ring seals on the rods.

21. Install rods (6) and (5). Apply 9S-3263 Thread Lock Compound on threads and tighten to a torque
of 79 ± 4 N·m (60 ± 3 lb ft).

22. Install the following components in the head: seat (9), spring (8) and poppet (7).

23. If necessary, install pin (10) and the cup in the head.

Illustration 11 g00630320

24. Install six allen head screws (3) and head (4) on the piston pump. Tighten the four small screws to
a torque of 115 ± 12 N·m (85 ± 9 lb ft). Tighten the two large screws to a torque of 285 ± 30 N·m
(210 ± 22 lb ft).

Illustration 12 g00707880

25. Assemble compensator valve (2).


Reference: Refer to Disassembly and Assembly, Compensator Valve - Assemble in this module.

26. Install four allen head screws (1) and compensator valve (2) on the implement pump. Tighten the
four screws to a torque of 34 ± 3 N·m (25 ± 2 lb ft).

End By:

a. Install the implement pump in the machine. See the procedure in Disassembly and Assembly,
Implement Pump - Install .
PIP-10181735
2024/07/08
05:30:48+03:00
i01022311
© 2024 Caterpillar Inc.

You might also like