STRUCTURAL ANALYSIS

AND
DESIGN REPORT

CONCEPCION
RESIDENCE

Location: 3252 SUPA ST., U.P.S.-2, PARAÑAQUE CITY

Owner: MR. AND MRS. CONCEPCION
I. PROJECT DETAILS

Project Name : CONCEPCION RESIDENCE

Location : 3252 SUPA ST., U.P.S.-2, PARAÑAQUE CITY

Occupancy Category : STANDARD OCCUPANCY STRUCTURE

Building Structural System : Moment Resisting Frame Systems – Special Reinforced Concrete MF’s

II. REFERENCE CODE AND STANDARDS

- National Structural Code of the Philippines
- National Building Code of the Philippines

III. MATERIAL SPECIFICATIONS

Concrete – reinforced concrete design shall be in accordance with NSCP 2015. The specified minimum
compressive strength of the concrete by cylinder test at 28days age shall be as follows:
Foundation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 20.7MPa (3000PSI)
Beams - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 20.7MPa (3000PSI)
Columns - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 20.7MPa (3000PSI)
Suspended Slab - - - - - - - - - - - - - - - - - - - - - - - - - - - 20.7MPa (3000PSI)
Slab on Grade - - - - - - - - - - - - - - - - - - - - - - - - - - - - 20.7MPa (3000PSI)
Lean Concrete - - - - - - - - - - - - - - - - - - - - - - - - - - - - -10.0MPa (1450PSI)

Reinforcing Steel – minimum yield strength of reinforcing bar shall be as follows:

16mmØ and smaller reinforcing bar - - - - - - - - - - - - - - 276MPa (Grade 40)

20mmØ and bigger reinforcing bar - - - - - - - - - - - - - - - 414MPa (Grade 60)

Structural Steel – All structural steel such as wide flange, angles, channels, pipes and plates shall conform to
ASTM A36 or equivalent with minimum yield strength of 248MPa.

Weld – Welding electrode shall be E70XX, minimum welding 6mm. Fu = 480MPa

Anchor Bolt – Anchor Bolt shall conform to ASTM 325 or equivalent. Anchor bolt shall be designed for maximum
tensile stress of 140MPa on the tensile stress area of the bolt.
IV. DESIGN LOAD CRITERIA

Dead Loads (DL) – consist of the weight of all materials of construction incorporated into the building or other
structure, including but not limited to walls, floors, roofs, ceilings, stairways, finishes, cladding and other similarly
incorporated architectural and structural items, and fixed service equipment, including the weight of cranes.
Live Loads (LL) – shall be the maximum loads expected by the intended use or occupancy but in no case shall
be less than the loads required by this section.
Roof Live Loads (LL) – shall be designed for the unit live loads, Lr, set forth in Table 205-3. The live loads shall
be assumed to act vertically upon the projected area on a horizontal plane.
Earthquake Loads (EQX & EQZ), section 208
V. LOAD COMBINATIONS
LOAD COMBINATION FOR DESIGN
LOAD COMB 7 1.4DL
LOAD COMB 8 1.2DL + 1.6LL
LOAD COMB 9 1.2DL + 1.0LL
LOAD COMB 10 1.53DL + 1.0LL + 1.25EQX
LOAD COMB 11 1.53DL + 1.0LL + 1.25EQZ
LOAD COMB 12 1.53DL + 1.0LL - 1.25EQX
LOAD COMB 13 1.53DL + 1.0LL - 1.25EQZ
LOAD COMB 14 0.9DL + 1.0EQX
LOAD COMB 15 0.9DL + 1.0EQX
LOAD COMB 16 0.9DL - 1.0EQZ
LOAD COMB 17 0.9DL - 1.0EQZ
LOAD COMB 18 0.57DL + 1.25EQX
LOAD COMB 19 0.57DL + 1.25EQX
LOAD COMB 20 0.57DL - 1.25EQZ
LOAD COMB 21 0.57DL - 1.25EQZ

LOAD COMBINATION FOR DRIFT CHECK

LOAD COMB 8 1.2DL + 1.6LL
LOAD COMB 9 1.2DL + 1.0LL
LOAD COMB 10 1.53DL + 1.0LL + 1.25EQX
LOAD COMB 11 1.53DL + 1.0LL + 1.25EQZ
LOAD COMB 12 1.53DL + 1.0LL - 1.25EQX
LOAD COMB 13 1.53DL + 1.0LL - 1.25EQZ
LOAD COMB 14 0.9DL + 1.0EQX
LOAD COMB 15 0.9DL + 1.0EQX
LOAD COMB 16 0.9DL - 1.0EQZ
LOAD COMB 17 0.9DL - 1.0EQZ
LOAD COMB 18 0.57DL + 1.25EQX
LOAD COMB 19 0.57DL + 1.25EQX
LOAD COMB 20 0.57DL - 1.25EQZ
LOAD COMB 21 0.57DL - 1.25EQZ

LOAD COMBINATION FOR DEFLECTION CHECK

LOAD COMB 6 1.4DL
LOAD COMB 7 1.2DL + 1.6LL
VI. GEOMETRY

3D STRUCTURAL RENDERED VIEW

STRUCTURAL GEOMETRIC MODEL VIEW

VII. LOAD CALCULATION

Dead Load
1) Selfweight
Steel unit weight = 76.82 kN/m3
Concrete unit weight = 23.60 kN/m3

2) Member Load (21.20 kN/m3) Weight (kPa) height(m)

150mm CHB = 2.63 + 0.24(2) = 3.11 2.7 8.4 kN-m
150mm CHB = 2.63 + 0.24(2) = 3.11 2.6 8.1 kN-m
100mm CHB = 2.5 + 0.24(2) = 2.98 2.7 8 kN-m
100mm CHB = 2.5 + 0.24(2) = 2.98 2.6 7.7 kN-m

Tie
Floor Load Units 2ND FLOOR ROOF Bea
ms
SLAB (100MM THK) kN/m2 2.40 -
FLOOR FINISH kN/m2 0.77 -
TOPPINGS kN/m2 0.60 -
CEILING kN/m2 0.10 0.10
DUCTING/MEPF kN/m2 0.20 0.20
ROOFING SHEET kN/m2 - 0.10
ROOF RAMING kN/m2 - 0.41
PARTITION WALL kN/m2 0.50 - 0
4.57 0.81
VIII. STAAD OUTPUT ANALYSIS
 Friday, 17 May 2024 3:35 pm

PAGE NO. 1

****************************************************
* *
* STAAD.Pro CONNECT Edition *
* Version 22.00.00.15 *
* Proprietary Program of *
* Bentley Systems, Inc. *
* Date= MAY 17, 2024 *
* Time= 15:35:53 *
* *
* Licensed to: only @ ::LAVTeam:: (R) *
****************************************************

1. STAAD SPACE DXF IMPORT OF DRAWING1.DXF

INPUT FILE: C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.STD
2. START JOB INFORMATION
3. ENGINEER DATE 17-MAY-24
4. END JOB INFORMATION
5. INPUT WIDTH 79
6. UNIT METER KN
7. JOINT COORDINATES
8. 1 0 0 -10.7; 2 0 0 -7.15; 3 0 0 -2.77518; 4 0 0 0; 5 0 3.45 -10.7
9. 6 0 3.45 -7.15; 7 0 3.45 -2.77518; 8 0 3.45 0; 9 2.95 0 -10.7
10. 11 2.95 0 -2.78345; 12 2.95 0 0.000115897; 13 2.95 3.45 -10.7
11. 14 2.95 3.45 -7.15; 15 2.95 3.45 -2.78345; 16 2.95 3.45 0.000115897
12. 17 5.7 0 -10.7; 18 5.7 0 -7.15; 20 5.7 3.45 -10.7; 21 5.7 3.45 -7.15
13. 22 5.7 3.45 -2.79116; 23 5.825 0 0.000228848; 24 5.825 3.45 0.000228848
14. 25 8.63403 0 -10.7; 26 8.63403 3.45 -10.7; 27 8.85 0 -2.8
15. 28 8.85 0 0.000347692; 29 8.85 3.45 -2.8; 30 8.85 3.45 0.000347692
16. 31 9.64586 0 -7.15; 32 9.64586 3.45 -7.15; 33 10.8841 0 -2.8057
17. 34 10.8841 3.45 -2.8057; 35 11.6839 0 0.000459028; 36 11.6839 3.45 0.000459028
18. 38 2.95 3.45 0.525116; 39 5.825 3.45 0.525229; 40 8.85 3.45 0.525348
19. 41 8.85 3.45 -7.15; 43 8.85 3.45 -4.375; 45 10.4355 3.45 -4.37944
20. 46 0 3.45 -11.625; 47 2.95 3.45 -11.625; 48 5.7 3.45 -11.775
21. 49 2.95 3.45 -11.775; 50 5.7 3.45 -3.26616; 51 8.85 3.45 -3.275
22. 53 5.825 3.45 -2.79151; 54 5.7 3.45 -4.36616; 55 0 6.45 -10.7; 56 0 6.45 -7.15
23. 57 0 6.45 -2.77518; 58 0 6.45 0; 59 2.95 6.45 -10.7; 60 2.95 6.45 -7.15
24. 61 2.95 6.45 -2.78345; 62 2.95 6.45 0.000115897; 63 5.7 6.45 -10.7
25. 64 5.7 6.45 -7.15; 65 8.63403 6.45 -10.7; 66 8.85 6.45 -2.8
26. 67 8.85 6.45 0.000347692; 68 9.64586 6.45 -7.15; 69 10.8841 6.45 -2.8057
27. 70 11.6839 6.45 0.000459028; 71 5.825 6.45 0.525229; 72 2.95 6.45 0.525116
28. 73 8.85 6.45 0.525348; 74 8.85 6.45 -7.15; 75 2.95 6.45 -4.16388
29. 77 8.85 6.45 -4.16365
30. MEMBER INCIDENCES
31. 1 1 5; 2 2 6; 3 3 7; 4 4 8; 5 5 6; 6 6 7; 7 7 8; 8 13 5; 9 6 14; 10 7 15
32. 11 8 16; 12 9 13; 14 11 15; 15 12 16; 16 13 14; 17 14 15; 18 15 16; 19 20 13
33. 20 14 21; 21 15 22; 22 16 24; 23 17 20; 24 18 21; 26 20 21; 27 21 54; 28 23 24
34. 29 26 20; 30 22 53; 31 24 30; 32 21 41; 33 25 26; 34 27 29; 35 28 30; 37 32 26
35. 38 31 32; 40 32 45; 41 30 36; 42 33 34; 43 36 34; 44 35 36; 46 16 38; 47 24 39
36. 48 30 40; 49 38 39; 50 39 40; 51 41 32; 53 41 43; 54 43 51; 55 43 45; 56 45 34
37. 57 5 46; 58 13 47; 59 47 46; 60 48 49; 61 20 48; 62 47 49; 63 50 22; 65 50 51
38. 67 53 29; 68 53 24; 69 54 50; 70 54 43; 71 29 30; 72 51 29; 73 29 34; 74 5 55

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 1 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 2

39. 75 6 56; 76 7 57; 77 8 58; 78 13 59; 80 15 61; 81 16 62; 82 20 63; 83 21 64

40. 84 26 65; 85 29 66; 86 30 67; 87 32 68; 88 34 69; 89 36 70; 90 39 71; 91 55 59
41. 92 59 63; 93 63 65; 94 65 68; 95 68 69; 96 69 70; 97 55 56; 98 56 57; 99 57 58
42. 100 58 62; 101 56 60; 102 60 64; 103 64 74; 104 57 61; 105 60 75; 106 61 62
43. 107 66 67; 108 62 72; 109 67 73; 110 72 71; 111 71 73; 112 74 68; 113 74 77
44. 114 75 61; 115 75 77; 116 77 66; 117 63 64
45. START GROUP DEFINITION
46. FLOOR
47. _2F_2W 5 TO 11 16 TO 22 26 27 29 TO 32 37 40 51 53 55 63 67 TO 71
48. _2F_1W 8 19 30 57 TO 63 65 67 72
49. _ROOF 91 TO 94 97 TO 117
50. END GROUP DEFINITION
51. DEFINE MATERIAL START
52. ISOTROPIC CONCRETE
53. E 2.17185E+07
54. POISSON 0.17
55. DENSITY 23.5616
56. ALPHA 1E-05
57. DAMP 0.05
58. TYPE CONCRETE
59. STRENGTH FCU 27579
60. END DEFINE MATERIAL
61. MEMBER PROPERTY AMERICAN
62. 1 TO 4 12 14 15 23 24 28 33 TO 35 38 42 44 74 TO 78 80 TO 88 -
63. 89 PRIS YD 0.25 ZD 0.4
64. 9 10 20 21 30 32 51 67 PRIS YD 0.45 ZD 0.2
65. 5 TO 8 11 16 TO 19 22 26 27 29 31 37 40 43 46 TO 50 53 54 56 TO 58 61 TO 63 -
66. 68 69 71 72 90 101 TO 103 105 TO 116 PRIS YD 0.4 ZD 0.2
67. 41 55 59 60 65 70 73 91 TO 100 104 117 PRIS YD 0.3 ZD 0.2
68. CONSTANTS
69. BETA 90 MEMB 4 23 77 82
70. BETA 195.911 MEMB 33 38 42 44 84 87 TO 89
71. MATERIAL CONCRETE ALL
72. MEMBER CRACKED
73. 1 TO 4 12 14 15 23 24 28 33 TO 35 38 42 44 74 TO 78 80 TO 89 -
74. 90 REDUCTION RIY 0.700000 RIZ 0.700000
75. 5 TO 11 16 TO 22 26 27 29 TO 32 37 40 41 43 46 TO 51 53 TO 63 65 67 TO 73 -
76. 91 TO 117 REDUCTION RIY 0.350000 RIZ 0.350000
77. MEMBER RELEASE
78. 49 50 55 59 60 65 70 115 START MZ
79. 49 50 55 59 60 65 70 115 END MZ
80. SUPPORTS
81. 1 TO 4 9 11 12 17 18 23 25 27 28 31 33 35 FIXED
82. DEFINE REFERENCE LOADS
83. LOAD R1 LOADTYPE DEAD TITLE REF DEAD LOAD
84. SELFWEIGHT Y 1
85. FLOOR LOAD
86. _2F_2W FLOAD 4.57 GY
87. ONEWAY LOAD
88. _2F_1W ONE 4.07 GY
89. MEMBER LOAD
90. 5 TO 7 11 29 37 40 43 46 48 TO 50 56 UNI GY 8.4
91. 16 18 26 71 UNI GY 8.05
92. FLOOR LOAD
93. _ROOF FLOAD 0.81 GY
94. MEMBER LOAD

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 2 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 3

95. 94 TO 99 UNI GY 3.732

96. LOAD R2 LOADTYPE LIVE TITLE REF LIVE LOAD
97. FLOOR LOAD
98. _2F_2W FLOAD 1.9 GY
99. ONEWAY LOAD
100. _2F_1W ONE 1.9 GY
101. FLOOR LOAD
102. _ROOF FLOAD 0.6 GY
103. END DEFINE REFERENCE LOADS

*** NOTE: NEITHER "MASS" NOR "GRAVITY" REFERENCE LOADTYPE IS PRESENT.

MASS MODEL IS FORMED BY COMBINING ALL "DEAD" AND "LIVE" (IF ANY) REFERENCE LOADTYPES.

*** NOTE: MASS MODEL FORMED WILL BE USED IN SEISMIC/RESPONSE/TIME HISTORY LOADING, IF ANY.
IF MASS MODEL IS SEPARATELY PROVIDED IN INDIVIDUAL LOADING, THE GENERATED MASS
WILL BE REPLACED BY THE MASS PROVIDED IN INDIVIDUAL LOADING.

104. FLOOR DIAPHRAGM

105. DIA 1 TYPE RIG HEI 3.45 JOINT 5 TO 8 13 TO 16 20 TO 22 24 26 29 30 32 34 36 -
106. 38 TO 41 43 45 TO 51 53 54
107. DIA 2 TYPE RIG HEI 6.45 JOINT 55 TO 75 77
108. CHECK SOFT STORY ASCE7

FLOOR DIAPHRAGM

************************************************************************************

FLOOR DIAPHRAGM UNIT - KN METE

--------------- ----------------

NO. TYPE FL. LEVEL FL. WT CENTRE OF MASS MASTER JOINT NO.
X Z

1 RIGID 3.450 1378.72 4.844 -5.197 78

2 RIGID 6.450 402.42 4.944 -5.081 79

************************************************************************************

109. DEFINE UBC LOAD

110. ZONE 0.4 I 1 RWX 8.5 RWZ 8.5 STYP 4 CT 0.0731 NA 1 NV 1
111. REFERENCE LOAD Y

*** NOTE: SEISMIC WEIGHT TABLE IS PRESENT.THIS WEIGHT TABLE

WILL BE CONSIDERED IN STATIC SEISMIC ANALYSIS.

112. R1 1.0
113. LOAD 1 LOADTYPE SEISMIC TITLE EQ+X
114. UBC LOAD X 1 DEC 1 ACC 0.05
115. PERFORM ANALYSIS

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 3 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 4

P R O B L E M S T A T I S T I C S
-----------------------------------

NUMBER OF JOINTS 72 NUMBER OF MEMBERS 108

NUMBER OF PLATES 0 NUMBER OF SOLIDS 0
NUMBER OF SURFACES 0 NUMBER OF SUPPORTS 16

Using 64-bit analysis engine.

SOLVER USED IS THE OUT-OF-CORE BASIC SOLVER

ORIGINAL/FINAL BAND-WIDTH= 44/ 14/ 172 DOF

TOTAL PRIMARY LOAD CASES = 1, TOTAL DEGREES OF FREEDOM = 174
TOTAL LOAD COMBINATION CASES = 0 SO FAR.
SIZE OF STIFFNESS MATRIX = 30 DOUBLE KILO-WORDS
REQRD/AVAIL. DISK SPACE = 12.5/ 372304.1 MB

SOFT STORY CHECK

VERTICAL STRUCTURAL IRREGULARITIES : SOFT STORY CHECK - ASCE/SEI 7-05

-------- ---------- --------------

STORY FL. LEVEL IN METE S T A T U S

----- ----------------- --------------------
X Z

1 3.45 OK OK
2 6.45 OK OK

NOTE : NO SOFT STOREY IS DETECTED.

***********************************************************
* *
* X DIRECTION : Ta = 0.296 Tb = 0.475 Tuser = 0.000 *
* T = 0.296, LOAD FACTOR = 1.000 *
* UBC TYPE = 97 *
* UBC FACTOR V = 0.1294 x 1594.50 = 206.35 KN *
* *
***********************************************************

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 4 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 5

************************************************************************

***NOTE: SEISMIC LOAD IS ACTING AT CENTER OF MASS FOR RIGID DIAPHRAGM.

TORSION FROM STATIC ECCENTRICITY (esi) IS INCLUDED IN ANALYSIS.
DYNAMIC ECCENTRICITY APPLIED = DEC - 1

LOAD NO.: 1 DIRECTION : X UNIT - METE

STORY LEVEL DYN. ECC. (dec) ACC. ECC. (aec) DESIGN ECC.
----- ----- --------------- --------------- ---------------
X Z X Z X Z
dec + aec dec + aec

1 3.45 0.00 0.00 0.58 0.62 0.00 0.62

2 6.45 0.00 0.00 0.58 0.56 0.00 0.56

************************************************************************

116. CHANGE
117. LOAD 2 LOADTYPE SEISMIC TITLE EQ+Z
118. UBC LOAD Z 1 DEC 1 ACC 0.05
119. PERFORM ANALYSIS

SOFT STORY CHECK

VERTICAL STRUCTURAL IRREGULARITIES : SOFT STORY CHECK - ASCE/SEI 7-05

-------- ---------- --------------

STORY FL. LEVEL IN METE S T A T U S

----- ----------------- --------------------
X Z

1 3.45 OK OK
2 6.45 OK OK

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 5 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 6

NOTE : NO SOFT STOREY IS DETECTED.

***********************************************************
* *
* Z DIRECTION : Ta = 0.296 Tb = 0.395 Tuser = 0.000 *
* T = 0.296, LOAD FACTOR = 1.000 *
* UBC TYPE = 97 *
* UBC FACTOR V = 0.1294 x 1594.50 = 206.35 KN *
* *
***********************************************************

************************************************************************

***NOTE: SEISMIC LOAD IS ACTING AT CENTER OF MASS FOR RIGID DIAPHRAGM.

TORSION FROM STATIC ECCENTRICITY (esi) IS INCLUDED IN ANALYSIS.
DYNAMIC ECCENTRICITY APPLIED = DEC - 1

LOAD NO.: 2 DIRECTION : Z UNIT - METE

STORY LEVEL DYN. ECC. (dec) ACC. ECC. (aec) DESIGN ECC.
----- ----- --------------- --------------- ---------------
X Z X Z X Z
dec + aec dec + aec

1 3.45 0.00 0.00 0.58 0.62 0.58 0.00

2 6.45 0.00 0.00 0.58 0.56 0.58 0.00

************************************************************************

120. CHANGE
121. LOAD 3 LOADTYPE SEISMIC TITLE EQ-X
122. UBC LOAD X -1 DEC 1 ACC 0.05
123. PERFORM ANALYSIS

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 6 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 7

SOFT STORY CHECK

VERTICAL STRUCTURAL IRREGULARITIES : SOFT STORY CHECK - ASCE/SEI 7-05

-------- ---------- --------------

STORY FL. LEVEL IN METE S T A T U S

----- ----------------- --------------------
X Z

1 3.45 OK OK
2 6.45 OK OK

NOTE : NO SOFT STOREY IS DETECTED.

***********************************************************
* *
* X DIRECTION : Ta = 0.296 Tb = 0.475 Tuser = 0.000 *
* T = 0.296, LOAD FACTOR = -1.000 *
* UBC TYPE = 97 *
* UBC FACTOR V = 0.1294 x 1594.50 = 206.35 KN *
* *
***********************************************************

************************************************************************

***NOTE: SEISMIC LOAD IS ACTING AT CENTER OF MASS FOR RIGID DIAPHRAGM.

TORSION FROM STATIC ECCENTRICITY (esi) IS INCLUDED IN ANALYSIS.
DYNAMIC ECCENTRICITY APPLIED = DEC - 1

LOAD NO.: 3 DIRECTION : X UNIT - METE

STORY LEVEL DYN. ECC. (dec) ACC. ECC. (aec) DESIGN ECC.
----- ----- --------------- --------------- ---------------
X Z X Z X Z
dec + aec dec + aec

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 7 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 8

1 3.45 0.00 0.00 0.58 0.62 0.00 0.62

2 6.45 0.00 0.00 0.58 0.56 0.00 0.56

************************************************************************

124. CHANGE
125. LOAD 4 LOADTYPE SEISMIC TITLE EQ-Z
126. UBC LOAD Z -1 DEC 1 ACC 0.05
127. PERFORM ANALYSIS

SOFT STORY CHECK

VERTICAL STRUCTURAL IRREGULARITIES : SOFT STORY CHECK - ASCE/SEI 7-05

-------- ---------- --------------

STORY FL. LEVEL IN METE S T A T U S

----- ----------------- --------------------
X Z

1 3.45 OK OK
2 6.45 OK OK

NOTE : NO SOFT STOREY IS DETECTED.

***********************************************************
* *
* Z DIRECTION : Ta = 0.296 Tb = 0.395 Tuser = 0.000 *
* T = 0.296, LOAD FACTOR = -1.000 *
* UBC TYPE = 97 *
* UBC FACTOR V = 0.1294 x 1594.50 = 206.35 KN *
* *
***********************************************************

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 8 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 9

************************************************************************

***NOTE: SEISMIC LOAD IS ACTING AT CENTER OF MASS FOR RIGID DIAPHRAGM.

TORSION FROM STATIC ECCENTRICITY (esi) IS INCLUDED IN ANALYSIS.
DYNAMIC ECCENTRICITY APPLIED = DEC - 1

LOAD NO.: 4 DIRECTION : Z UNIT - METE

STORY LEVEL DYN. ECC. (dec) ACC. ECC. (aec) DESIGN ECC.
----- ----- --------------- --------------- ---------------
X Z X Z X Z
dec + aec dec + aec

1 3.45 0.00 0.00 0.58 0.62 0.58 0.00

2 6.45 0.00 0.00 0.58 0.56 0.58 0.00

************************************************************************

128. CHANGE
129. LOAD 5 LOADTYPE DEAD TITLE DL
130. REFERENCE LOAD
131. R1 -1.0
132. LOAD 6 LOADTYPE LIVE TITLE LL
133. REFERENCE LOAD
134. R2 -1.0
135. LOAD COMB 7 ULC, 1.4 DEAD
136. 5 1.4
137. LOAD COMB 8 ULC, 1.2 DEAD + 1.6 LIVE
138. 5 1.2 6 1.6
139. LOAD COMB 11 ULC, 1.2 DEAD + 0.5 LIVE + 1 SEISMIC (X)
140. 5 1.2 6 0.5 1 1.0
141. LOAD COMB 12 ULC, 1.2 DEAD + 0.5 LIVE + 1 SEISMIC (Z)
142. 5 1.2 6 0.5 2 1.0
143. LOAD COMB 13 ULC, 1.2 DEAD + 0.5 LIVE + 1 SEISMIC (-X)
144. 5 1.2 6 0.5 3 1.0
145. LOAD COMB 14 ULC, 1.2 DEAD + 0.5 LIVE + 1 SEISMIC (-Z)
146. 5 1.2 6 0.5 4 1.0
147. LOAD COMB 15 ULC, 0.9 DEAD + 1 SEISMIC (X)
148. 5 0.9 1 1.0
149. LOAD COMB 16 ULC, 0.9 DEAD + 1 SEISMIC X)
150. 5 0.9 2 1.0
151. LOAD COMB 17 ULC, 0.9 DEAD + 1 SEISMIC (-X)
152. 5 0.9 3 1.0
153. LOAD COMB 18 ULC, 0.9 DEAD + 1 SEISMIC (-Z)
154. 5 0.9 4 1.0

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 9 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 10

155. PERFORM ANALYSIS

SOFT STORY CHECK

VERTICAL STRUCTURAL IRREGULARITIES : SOFT STORY CHECK - ASCE/SEI 7-05

-------- ---------- --------------

STORY FL. LEVEL IN METE S T A T U S

----- ----------------- --------------------
X Z

1 3.45 OK OK
2 6.45 OK OK

NOTE : NO SOFT STOREY IS DETECTED.

156. LOAD LIST 7 8 11 TO 18

157. PRINT STORY DRIFT 0.004200
STORY DRIFT 0.004200

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 10 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 11

STORY HEIGHT LOAD AVG. DISP(CM ) DRIFT(CM ) RATIO STATUS

------------------------------------------------------------------------------------------
(METE) X Z X Z

BASE= 0.00 ALLOW. DRIFT = L / 238

1 0.00 7 0.0000 0.0000 0.0000 0.0000 L /999999 PASS

8 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
11 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
12 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
13 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
14 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
15 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
16 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
17 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
18 0.0000 0.0000 0.0000 0.0000 L /999999 PASS

2 3.45 7 0.0118 0.0131 0.0118 0.0131 L / 26296 PASS

8 0.0139 0.0057 0.0139 0.0057 L / 24800 PASS
11 0.6860 -0.0173 0.6860 0.0173 L / 503 PASS
12 -0.0204 0.4610 0.0204 0.4610 L / 748 PASS
13 -0.6622 0.0456 0.6622 0.0456 L / 521 PASS
14 0.0442 -0.4327 0.0442 0.4327 L / 797 PASS
15 0.6823 -0.0183 0.6823 0.0183 L / 505 PASS

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 11 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 12

16 -0.0242 0.4599 0.0242 0.4599 L / 750 PASS

17 -0.6659 0.0446 0.6659 0.0446 L / 518 PASS
18 0.0405 -0.4338 0.0405 0.4338 L / 795 PASS

3 6.45 7 0.0285 0.0167 0.0167 0.0035 L / 17983 PASS

8 0.0353 -0.0022 0.0214 0.0079 L / 14021 PASS
11 1.1392 -0.0390 0.4533 0.0217 L / 662 PASS
12 -0.0236 0.8241 0.0032 0.3632 L / 826 PASS
13 -1.0768 0.0699 0.4145 0.0242 L / 723 PASS
14 0.0861 -0.7933 0.0419 0.3605 L / 832 PASS
15 1.1297 -0.0374 0.4475 0.0191 L / 670 PASS
16 -0.0331 0.8257 0.0090 0.3658 L / 820 PASS
17 -1.0863 0.0714 0.4203 0.0269 L / 714 PASS
18 0.0766 -0.7917 0.0362 0.3579 L / 838 PASS
158. PRINT DIA CR
DIA CR

************************************************************

CENTRE OF RIGIDITY UNIT - METE

------------------ -----------

DIAPHRAM FL. LEVEL X-COORDINATE Z-COORDINATE

1 3.450 5.394 -5.256

2 6.450 5.386 -5.354

************************************************************

159. START CONCRETE DESIGN

CONCRETE DESIGN
160. CODE ACI 2011
161. FC 20700 ALL
162. FYMAIN 276000 ALL
163. FYSEC 230000 ALL
164. REINF 0 MEMB 1 TO 4 12 14 15 23 24 28 33 TO 35 38 42 44 74 TO 78 80 TO 90
165. TRACK 2 ALL
166. END CONCRETE DESIGN
167. PRINT MEMBER FORCES GLOBAL LIST ALL
MEMBER FORCES GLOBAL ALL

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 12 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 13

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

1 7 1 1.54 96.08 1.87 1.57 -0.02 -1.66

5 -1.54 -84.70 -1.87 4.90 0.02 -3.66
8 1 1.86 96.63 1.96 1.94 -0.02 -1.99
5 -1.86 -86.87 -1.96 4.84 0.02 -4.44
11 1 -7.72 72.74 0.92 -0.31 -0.40 17.10
5 7.72 -62.99 -0.92 3.47 0.40 9.53
12 1 3.22 75.92 -13.74 -33.83 -0.52 -5.07
5 -3.22 -66.16 13.74 -13.59 0.52 -6.03
13 1 12.12 100.80 -0.42 -3.11 -0.22 -23.16
5 -12.12 -91.04 0.42 1.66 0.22 -18.66
14 1 1.16 97.62 14.30 30.52 -0.09 -0.94
5 -1.16 -87.87 -14.30 18.82 0.09 -3.06
15 1 -8.22 47.69 0.40 -0.83 -0.40 17.63
5 8.22 -40.38 -0.40 2.22 0.40 10.72
16 1 2.72 50.87 -14.26 -34.35 -0.52 -4.54
5 -2.72 -43.55 14.26 -14.83 0.52 -4.84
17 1 11.62 75.75 -0.93 -3.63 -0.22 -22.63
5 -11.62 -68.44 0.93 0.42 0.22 -17.47
18 1 0.66 72.58 13.79 30.00 -0.09 -0.41
5 -0.66 -65.26 -13.79 17.58 0.09 -1.87

2 7 2 9.21 209.45 0.75 0.29 -0.02 -10.40

6 -9.21 -198.07 -0.75 2.29 0.02 -21.38
8 2 10.81 219.25 1.01 0.85 -0.02 -12.20
6 -10.81 -209.49 -1.01 2.62 0.02 -25.10
11 2 -0.69 183.74 -0.15 -1.52 -0.40 9.61
6 0.69 -173.98 0.15 1.01 0.40 -7.23
12 2 9.91 197.82 -17.56 -38.16 -0.52 -12.00
6 -9.91 -188.07 17.56 -22.43 0.52 -22.17
13 2 18.80 201.35 -1.69 -4.55 -0.22 -30.49
6 -18.80 -191.60 1.69 -1.28 0.22 -34.37
14 2 8.19 187.27 15.80 32.22 -0.09 -8.86
6 -8.19 -177.52 -15.80 22.28 0.09 -19.40
15 2 -3.58 126.44 -0.42 -1.77 -0.40 12.87
6 3.58 -119.13 0.42 0.31 0.40 -0.53
16 2 7.02 140.53 -17.84 -38.41 -0.52 -8.75
6 -7.02 -133.21 17.84 -23.12 0.52 -15.47
17 2 15.91 144.06 -1.97 -4.80 -0.22 -27.23
6 -15.91 -136.74 1.97 -1.98 0.22 -27.67
18 2 5.31 129.97 15.52 31.97 -0.09 -5.60
6 -5.31 -122.66 -15.52 21.58 0.09 -12.70

3 7 3 0.74 140.43 -3.19 -4.18 -0.02 -0.67

7 -0.74 -129.05 3.19 -6.83 0.02 -1.89

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 13 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 14

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

8 3 0.93 139.25 -3.05 -3.75 -0.02 -0.86

7 -0.93 -129.50 3.05 -6.77 0.02 -2.36
11 3 -10.48 106.15 -3.77 -5.63 -0.40 21.50
7 10.48 -96.39 3.77 -7.38 0.40 14.66
12 3 0.72 116.08 -20.89 -41.94 -0.52 -0.60
7 -0.72 -106.32 20.89 -30.14 0.52 -1.87
13 3 11.28 143.49 -5.24 -8.59 -0.22 -21.50
7 -11.28 -133.74 5.24 -9.51 0.22 -17.40
14 3 0.09 133.55 11.95 27.85 -0.09 0.57
7 -0.09 -123.80 -11.95 13.37 0.09 -0.88
15 3 -10.73 70.15 -2.99 -4.68 -0.40 21.73
7 10.73 -62.84 2.99 -5.63 0.40 15.30
16 3 0.46 80.08 -20.11 -40.99 -0.52 -0.36
7 -0.46 -72.77 20.11 -28.38 0.52 -1.24
17 3 11.02 107.50 -4.46 -7.64 -0.22 -21.27
7 -11.02 -100.19 4.46 -7.76 0.22 -16.76
18 3 -0.16 97.56 12.73 28.80 -0.09 0.81
7 0.16 -90.25 -12.73 15.12 0.09 -0.25

4 7 4 2.27 86.58 -1.60 -2.05 -0.02 -2.06

8 -2.27 -75.20 1.60 -3.48 0.02 -5.78
8 4 2.16 81.11 -1.53 -1.86 -0.02 -1.88
8 -2.16 -71.35 1.53 -3.41 0.02 -5.59
11 4 -21.32 57.86 -1.84 -2.63 -0.40 49.65
8 21.32 -48.10 1.84 -3.71 0.40 23.91
12 4 0.58 93.81 -9.38 -17.85 -0.52 1.35
8 -0.58 -84.06 9.38 -14.51 0.52 -3.36
13 4 22.50 95.35 -2.48 -3.87 -0.22 -46.94
8 -22.50 -85.60 2.48 -4.70 0.22 -30.69
14 4 0.66 59.40 5.08 11.40 -0.09 1.24
8 -0.66 -49.64 -5.08 6.14 0.09 -3.52
15 4 -21.88 37.15 -1.45 -2.16 -0.40 50.12
8 21.88 -29.83 1.45 -2.83 0.40 25.35
16 4 0.03 73.10 -8.99 -17.38 -0.52 1.83
8 -0.03 -65.79 8.99 -13.63 0.52 -1.93
17 4 21.95 74.64 -2.09 -3.40 -0.22 -46.46
8 -21.95 -67.33 2.09 -3.82 0.22 -29.25
18 4 0.11 38.69 5.48 11.87 -0.09 1.72
8 -0.11 -31.37 -5.48 7.02 0.09 -2.08

5 7 5 -0.00 34.01 0.00 -19.69 -0.00 3.74

6 0.00 36.69 0.00 24.45 -0.00 -3.74
8 5 -0.00 33.86 0.00 -20.40 0.00 4.36
6 0.00 36.05 0.00 24.29 -0.00 -4.36
11 5 0.00 30.08 0.00 -17.00 -0.00 3.87
6 -0.00 33.42 0.00 22.92 -0.00 -3.87

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 14 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 15

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

12 5 -0.00 20.49 0.00 0.65 0.00 3.84

6 0.00 43.01 0.00 39.32 0.00 -3.84
13 5 -0.00 29.48 0.00 -15.89 0.00 3.49
6 0.00 34.02 0.00 23.94 -0.00 -3.49
14 5 0.00 39.08 0.00 -33.56 -0.00 3.52
6 -0.00 24.42 0.00 7.54 -0.00 -3.52
15 5 0.00 21.33 0.00 -11.68 -0.00 2.71
6 -0.00 24.12 0.00 16.64 -0.00 -2.71
16 5 -0.00 11.74 0.00 5.97 -0.00 2.68
6 0.00 33.71 0.00 33.04 0.00 -2.68
17 5 -0.00 20.73 0.00 -10.57 0.00 2.33
6 0.00 24.72 0.00 17.66 -0.00 -2.33
18 5 0.00 30.32 0.00 -28.24 -0.00 2.35
6 -0.00 15.12 0.00 1.26 -0.00 -2.35

6 7 6 -0.00 41.83 0.00 -31.68 -0.00 -3.30

7 0.00 41.80 0.00 31.62 -0.00 3.30
8 6 -0.00 40.87 0.00 -31.75 -0.00 -3.86
7 0.00 40.62 0.00 31.21 -0.00 3.86
11 6 -0.00 37.07 0.00 -27.81 -0.00 -3.39
7 0.00 37.68 0.00 29.16 -0.00 3.39
12 6 -0.00 31.32 0.00 -15.28 -0.00 -3.01
7 0.00 43.43 0.00 41.79 -0.00 3.01
13 6 -0.00 36.77 0.00 -27.16 -0.00 -2.70
7 0.00 37.98 0.00 29.83 -0.00 2.70
14 6 -0.00 42.52 0.00 -39.69 -0.00 -3.08
7 0.00 32.23 0.00 17.19 -0.00 3.08
15 6 -0.00 26.54 0.00 -19.58 -0.00 -2.36
7 0.00 27.22 0.00 21.10 -0.00 2.36
16 6 -0.00 20.79 0.00 -7.06 -0.00 -1.98
7 0.00 32.97 0.00 33.73 -0.00 1.98
17 6 -0.00 26.24 0.00 -18.94 -0.00 -1.67
7 0.00 27.53 0.00 21.77 -0.00 1.67
18 6 -0.00 31.99 0.00 -31.47 -0.00 -2.05
7 0.00 21.77 0.00 9.13 -0.00 2.05

7 7 7 0.00 29.47 0.00 -16.86 0.00 0.12

8 -0.00 23.59 0.00 8.71 0.00 -0.12
8 7 0.00 29.13 0.00 -17.28 0.00 -0.02
8 -0.00 22.58 0.00 8.20 0.00 0.02
11 7 0.00 25.75 0.00 -14.31 0.00 1.72
8 -0.00 21.67 0.00 8.65 0.00 -1.72
12 7 0.00 12.83 0.00 4.18 0.00 0.30
8 -0.00 34.60 0.00 26.04 0.00 -0.30
13 7 -0.00 24.98 0.00 -13.19 -0.00 -1.20
8 0.00 22.45 0.00 9.69 -0.00 1.20

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 15 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 16

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

14 7 0.00 37.91 0.00 -31.69 -0.00 0.21

8 -0.00 9.51 0.00 -7.71 0.00 -0.21
15 7 0.00 18.23 0.00 -9.81 0.00 1.73
8 -0.00 15.88 0.00 6.56 0.00 -1.73
16 7 0.00 5.30 0.00 8.68 0.00 0.32
8 -0.00 28.81 0.00 23.94 0.00 -0.32
17 7 -0.00 17.46 0.00 -8.69 -0.00 -1.18
8 0.00 16.66 0.00 7.59 -0.00 1.18
18 7 0.00 30.39 0.00 -27.20 -0.00 0.23
8 -0.00 3.72 0.00 -9.81 0.00 -0.23

8 7 13 0.00 16.37 -0.00 1.50 -0.00 -9.05

5 0.00 13.11 0.00 -1.50 -0.00 4.24
8 13 0.00 20.05 -0.00 1.74 -0.00 -11.25
5 0.00 15.98 0.00 -1.74 -0.00 5.26
11 13 0.00 25.87 -0.00 1.26 0.00 -21.83
5 0.00 2.76 0.00 -1.26 0.00 -12.26
12 13 0.00 14.03 -0.00 1.29 -0.00 -6.34
5 0.00 14.60 0.00 -1.29 0.00 7.20
13 13 0.00 4.43 -0.00 1.31 0.00 6.14
5 0.00 24.20 0.00 -1.31 -0.00 23.02
14 13 0.00 16.28 -0.00 1.28 -0.00 -9.36
5 0.00 12.35 0.00 -1.28 -0.00 3.56
15 13 0.00 20.48 -0.00 0.79 0.00 -18.80
5 0.00 -1.53 0.00 -0.79 0.00 -13.67
16 13 0.00 8.64 -0.00 0.83 -0.00 -3.31
5 0.00 10.31 0.00 -0.83 0.00 5.78
17 13 0.00 -0.96 -0.00 0.85 0.00 9.17
5 0.00 19.91 0.00 -0.85 -0.00 21.60
18 13 0.00 10.89 -0.00 0.82 -0.00 -6.32
5 0.00 8.06 0.00 -0.82 -0.00 2.14

9 7 6 0.00 58.53 0.00 -0.18 -0.00 55.71

14 0.00 -15.23 -0.00 0.18 -0.00 53.10
8 6 0.00 69.78 0.00 -0.91 -0.00 65.96
14 0.00 -16.25 -0.00 0.91 -0.00 60.91
11 6 0.00 50.33 -0.00 -0.26 0.00 37.59
14 0.00 -8.09 0.00 0.26 0.00 48.58
12 6 0.00 57.59 -0.00 3.37 0.00 55.76
14 0.00 -15.35 0.00 -3.37 -0.00 51.82
13 6 0.00 62.62 0.00 0.07 -0.00 70.14
14 0.00 -20.37 -0.00 -0.07 -0.00 52.27
14 6 0.00 55.36 0.00 -3.56 -0.00 51.97
14 0.00 -13.12 -0.00 3.56 -0.00 49.02
15 6 0.00 31.66 -0.00 0.02 0.00 19.96
14 0.00 -3.83 0.00 -0.02 0.00 32.38

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 16 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 17

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

16 6 0.00 38.92 -0.00 3.64 0.00 38.13

14 0.00 -11.09 0.00 -3.64 -0.00 35.63
17 6 0.00 43.95 0.00 0.34 -0.00 52.51
14 0.00 -16.11 -0.00 -0.34 -0.00 36.08
18 6 0.00 36.69 0.00 -3.28 -0.00 34.34
14 0.00 -8.85 -0.00 3.28 -0.00 32.83

10 7 7 0.00 11.96 0.00 0.50 -0.00 1.73

15 -0.00 30.54 -0.00 -0.57 -0.00 -29.11
8 7 0.00 15.01 0.00 0.81 -0.00 2.70
15 -0.00 37.44 -0.00 -0.90 -0.00 -35.75
11 7 0.00 -3.26 -0.00 0.70 -0.00 -22.19
15 -0.00 44.69 0.00 -0.90 -0.00 -48.51
12 7 0.00 11.91 -0.00 0.73 -0.00 1.86
15 -0.00 29.52 0.00 -0.81 0.00 -27.82
13 7 -0.00 25.76 0.00 0.66 -0.00 24.37
15 0.00 15.68 -0.00 -0.61 -0.00 -9.48
14 7 0.00 10.59 0.00 0.63 -0.00 0.32
15 -0.00 30.84 -0.00 -0.71 -0.00 -30.17
15 7 0.00 -7.31 -0.00 0.48 -0.00 -22.94
15 -0.00 34.63 0.00 -0.65 -0.00 -38.89
16 7 0.00 7.86 -0.00 0.51 -0.00 1.11
15 -0.00 19.46 0.00 -0.56 0.00 -18.20
17 7 -0.00 21.70 0.00 0.43 -0.00 23.62
15 0.00 5.61 -0.00 -0.36 -0.00 0.13
18 7 0.00 6.54 0.00 0.40 -0.00 -0.43
15 -0.00 20.78 -0.00 -0.46 -0.00 -20.56

11 7 8 0.00 27.17 0.00 -0.68 0.00 12.27

16 -0.00 28.42 -0.00 0.68 0.00 -14.10
8 8 0.00 26.05 0.00 -0.54 0.00 11.88
16 -0.00 27.83 -0.00 0.54 0.00 -14.48
11 8 0.00 9.19 0.00 -0.44 0.00 -14.05
16 -0.00 40.41 -0.00 0.44 0.00 -32.01
12 8 0.00 23.34 0.00 -1.28 0.00 9.54
16 -0.00 26.25 -0.00 1.28 0.00 -13.83
13 8 0.00 37.26 0.00 -0.57 0.00 32.83
16 -0.00 12.33 -0.00 0.57 0.00 3.95
14 8 0.00 23.11 0.00 0.28 0.00 9.25
16 -0.00 26.49 -0.00 -0.28 0.00 -14.23
15 8 0.00 2.50 0.00 -0.31 0.00 -17.10
16 -0.00 33.24 -0.00 0.31 0.00 -28.23
16 8 0.00 16.66 0.00 -1.15 0.00 6.48
16 -0.00 19.08 -0.00 1.15 0.00 -10.05
17 8 0.00 30.58 0.00 -0.43 0.00 29.77
16 -0.00 5.16 -0.00 0.43 0.00 7.72

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 17 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 18

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

18 8 0.00 16.42 0.00 0.41 0.00 6.20

16 -0.00 19.31 -0.00 -0.41 0.00 -10.46

12 7 9 -0.56 139.38 8.47 9.12 -0.02 0.74

13 0.56 -128.00 -8.47 20.10 0.02 1.18
8 9 -0.65 153.23 9.57 10.63 -0.02 0.89
13 0.65 -143.48 -9.57 22.39 0.02 1.36
11 9 -12.20 128.17 8.35 9.31 -0.40 22.22
13 12.20 -118.41 -8.35 19.50 0.40 19.86
12 9 1.58 126.11 -5.54 -22.98 -0.52 -3.21
13 -1.58 -116.35 5.54 3.86 0.52 -2.26
13 9 12.89 131.92 6.37 5.26 -0.22 -24.04
13 -12.89 -122.16 -6.37 16.73 0.22 -20.43
14 9 -0.92 133.98 20.29 37.60 -0.09 1.44
13 0.92 -124.22 -20.29 32.41 0.09 1.74
15 9 -12.03 87.75 5.81 6.48 -0.40 21.99
13 12.03 -80.43 -5.81 13.58 0.40 19.50
16 9 1.76 85.69 -8.08 -25.81 -0.52 -3.44
13 -1.76 -78.37 8.08 -2.06 0.52 -2.62
17 9 13.06 91.50 3.84 2.42 -0.22 -24.27
13 -13.06 -84.18 -3.84 10.81 0.22 -20.79
18 9 -0.75 93.56 17.76 34.76 -0.09 1.21
13 0.75 -86.24 -17.76 26.49 0.09 1.38

14 7 11 3.66 214.13 -4.89 -6.04 -0.02 -4.00

15 -3.66 -202.75 4.89 -10.84 0.02 -8.61
8 11 4.51 250.78 -5.90 -6.93 -0.02 -4.96
15 -4.51 -241.03 5.90 -13.43 0.02 -10.61
11 11 -9.60 220.72 -4.58 -5.37 -0.40 20.49
15 9.60 -210.97 4.58 -10.44 0.40 12.64
12 11 3.30 184.01 -20.96 -40.49 -0.52 -3.55
15 -3.30 -174.26 20.96 -31.84 0.52 -7.82
13 11 15.96 187.99 -6.31 -9.14 -0.22 -26.86
15 -15.96 -178.24 6.31 -12.64 0.22 -28.20
14 11 3.08 224.70 10.10 26.03 -0.09 -2.84
15 -3.08 -214.95 -10.10 8.82 0.09 -7.77
15 11 -10.82 153.82 -3.00 -3.53 -0.40 21.83
15 10.82 -146.51 3.00 -6.82 0.40 15.49
16 11 2.08 117.11 -19.38 -38.64 -0.52 -2.22
15 -2.08 -109.80 19.38 -28.23 0.52 -4.96
17 11 14.75 121.10 -4.73 -7.30 -0.22 -25.53
15 -14.75 -113.78 4.73 -9.02 0.22 -25.35
18 11 1.86 157.80 11.68 27.87 -0.09 -1.51
15 -1.86 -150.49 -11.68 12.43 0.09 -4.91

15 7 12 -0.95 134.54 -1.00 -1.63 -0.02 1.29

16 0.95 -123.16 1.00 -1.83 0.02 1.99

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 18 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 19

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

8 12 -0.79 130.17 -1.40 -1.82 -0.02 1.13

16 0.79 -120.42 1.40 -3.01 0.02 1.60
11 12 -14.25 123.71 -0.73 -1.00 -0.40 26.25
16 14.25 -113.96 0.73 -1.52 0.40 22.93
12 12 -1.68 144.30 -15.48 -34.26 -0.52 2.71
16 1.68 -134.55 15.48 -19.16 0.52 3.09
13 12 10.99 118.37 -2.70 -5.04 -0.22 -20.93
16 -10.99 -108.62 2.70 -4.28 0.22 -16.97
14 12 -1.56 97.79 12.08 28.28 -0.09 2.56
16 1.56 -88.03 -12.08 13.41 0.09 2.82
15 12 -14.06 90.24 -0.35 -0.52 -0.40 25.97
16 14.06 -82.92 0.35 -0.68 0.40 22.54
16 12 -1.48 110.83 -15.10 -33.78 -0.52 2.42
16 1.48 -103.51 15.10 -18.31 0.52 2.69
17 12 11.18 84.90 -2.32 -4.56 -0.22 -21.21
16 -11.18 -77.58 2.32 -3.44 0.22 -17.36
18 12 -1.37 64.32 12.47 28.76 -0.09 2.28
16 1.37 -57.00 -12.47 14.25 0.09 2.43

16 7 13 -0.00 60.71 0.00 -56.80 -0.00 -0.86

14 0.00 27.39 0.00 -2.35 -0.00 0.86
8 13 -0.00 65.91 0.00 -63.94 0.00 -1.02
14 0.00 27.99 0.00 -3.38 -0.00 1.02
11 13 0.00 56.88 0.00 -54.38 -0.00 -2.78
14 -0.00 24.38 0.00 -3.30 -0.00 2.78
12 13 -0.00 52.10 0.00 -42.19 0.00 -0.53
14 0.00 29.16 0.00 1.47 0.00 0.53
13 13 -0.00 55.50 0.00 -51.56 0.00 1.36
14 0.00 25.76 0.00 -1.23 -0.00 -1.36
14 13 0.00 60.28 0.00 -63.76 -0.00 -0.89
14 -0.00 20.98 0.00 -6.01 -0.00 0.89
15 13 0.00 39.53 0.00 -37.44 -0.00 -2.51
14 -0.00 17.10 0.00 -2.37 -0.00 2.51
16 13 -0.00 34.75 0.00 -25.25 -0.00 -0.26
14 0.00 21.88 0.00 2.40 0.00 0.26
17 13 -0.00 38.15 0.00 -34.63 0.00 1.63
14 0.00 18.48 0.00 -0.30 -0.00 -1.63
18 13 0.00 42.93 0.00 -46.82 -0.00 -0.61
14 -0.00 13.70 0.00 -5.08 -0.00 0.61

17 7 14 -0.00 14.84 0.00 2.49 -0.00 2.40

15 0.00 36.49 0.00 44.76 -0.00 -2.40
8 14 -0.00 18.52 0.00 2.42 -0.00 2.91
15 0.00 44.40 0.00 54.08 -0.00 -2.91
11 14 -0.00 14.25 0.00 2.92 -0.00 4.12
15 0.00 35.66 0.00 43.83 -0.00 -4.12

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 19 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 20

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

12 14 -0.00 11.84 0.00 5.63 -0.00 2.20

15 0.00 38.07 0.00 51.64 -0.00 -2.20
13 14 -0.00 14.61 0.00 1.78 -0.00 0.57
15 0.00 35.30 0.00 43.40 -0.00 -0.57
14 14 -0.00 17.02 0.00 -0.93 -0.00 2.49
15 0.00 32.89 0.00 35.59 -0.00 -2.49
15 14 -0.00 9.26 0.00 2.30 -0.00 3.34
15 0.00 23.74 0.00 29.33 -0.00 -3.34
16 14 -0.00 6.85 0.00 5.01 -0.00 1.42
15 0.00 26.15 0.00 37.14 -0.00 -1.42
17 14 -0.00 9.62 0.00 1.16 -0.00 -0.21
15 0.00 23.38 0.00 28.89 -0.00 0.21
18 14 -0.00 12.03 0.00 -1.55 -0.00 1.71
15 0.00 20.97 0.00 21.09 -0.00 -1.71

18 7 15 -0.00 34.38 0.00 -20.51 -0.00 -2.82

16 0.00 30.27 0.00 14.79 -0.00 2.82
8 15 -0.00 37.05 0.00 -23.47 -0.00 -3.26
16 0.00 30.69 0.00 14.62 -0.00 3.26
11 15 0.00 31.88 0.00 -19.53 -0.00 -2.41
16 -0.00 27.39 0.00 13.27 -0.00 2.41
12 15 -0.00 16.91 0.00 0.83 -0.00 -2.47
16 0.00 42.36 0.00 34.58 -0.00 2.47
13 15 -0.00 30.57 0.00 -17.64 -0.00 -2.82
16 0.00 28.69 0.00 15.02 0.00 2.82
14 15 -0.00 45.55 0.00 -38.00 -0.00 -2.76
16 0.00 13.72 0.00 -6.30 0.00 2.76
15 15 0.00 22.14 0.00 -13.29 -0.00 -1.55
16 -0.00 19.42 0.00 9.49 -0.00 1.55
16 15 -0.00 7.17 0.00 7.07 -0.00 -1.61
16 0.00 34.39 0.00 30.81 -0.00 1.61
17 15 -0.00 20.84 0.00 -11.40 -0.00 -1.95
16 0.00 20.72 0.00 11.24 0.00 1.95
18 15 -0.00 35.81 0.00 -31.77 -0.00 -1.89
16 0.00 5.75 0.00 -10.08 0.00 1.89

19 7 20 0.00 14.33 0.00 -0.64 -0.00 -8.41

13 0.00 13.44 0.00 0.64 0.00 7.19
8 20 0.00 17.37 -0.00 -0.80 -0.00 -9.93
13 0.00 16.67 0.00 0.80 0.00 8.97
11 20 0.00 25.58 -0.00 -0.82 -0.00 -26.07
13 0.00 1.43 0.00 0.82 -0.00 -7.12
12 20 0.00 11.69 -0.00 -1.65 0.00 -4.71
13 0.00 15.32 0.00 1.65 0.00 9.70
13 20 0.00 0.35 -0.00 -0.75 -0.00 12.75
13 0.00 26.66 0.00 0.75 -0.00 23.43

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 20 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 21

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

14 20 0.00 14.24 0.00 0.09 0.00 -8.63

13 0.00 12.76 -0.00 -0.09 0.00 6.59
15 20 0.00 20.91 -0.00 -0.60 -0.00 -23.42
13 0.00 -3.06 0.00 0.60 -0.00 -9.54
16 20 0.00 7.02 -0.00 -1.43 0.00 -2.05
13 0.00 10.83 0.00 1.43 0.00 7.29
17 20 0.00 -4.31 0.00 -0.53 -0.00 15.40
13 0.00 22.17 0.00 0.53 -0.00 21.01
18 20 0.00 9.58 0.00 0.30 0.00 -5.98
13 0.00 8.27 -0.00 -0.30 0.00 4.18

20 7 14 0.00 -27.00 0.00 -0.32 0.00 -56.35

21 0.00 66.45 -0.00 0.32 0.00 -72.14
8 14 0.00 -30.26 0.00 0.05 0.00 -64.84
21 0.00 78.94 -0.00 -0.05 0.00 -85.32
11 14 0.00 -30.54 0.00 0.13 0.00 -55.48
21 0.00 69.00 -0.00 -0.13 -0.00 -81.39
12 14 0.00 -25.65 0.00 -3.73 -0.00 -54.56
21 0.00 64.11 -0.00 3.73 -0.00 -68.87
13 14 0.00 -19.99 -0.00 -0.48 -0.00 -51.48
21 0.00 58.45 0.00 0.48 0.00 -56.38
14 14 0.00 -24.88 -0.00 3.38 0.00 -52.40
21 0.00 63.34 0.00 -3.38 0.00 -68.90
15 14 0.00 -22.53 0.00 0.09 0.00 -38.24
21 0.00 47.89 -0.00 -0.09 -0.00 -58.59
16 14 0.00 -17.64 0.00 -3.77 -0.00 -37.31
21 0.00 43.00 -0.00 3.77 -0.00 -46.07
17 14 0.00 -11.98 -0.00 -0.52 -0.00 -34.23
21 0.00 37.34 0.00 0.52 0.00 -33.59
18 14 0.00 -16.87 -0.00 3.34 0.00 -35.16
21 0.00 42.23 0.00 -3.34 0.00 -46.11

21 7 15 -0.00 50.59 -0.00 3.87 0.00 50.31

22 0.00 -10.46 0.00 -3.63 0.00 34.39
8 15 -0.00 61.85 -0.00 4.37 0.00 61.43
22 0.00 -12.27 0.00 -4.09 0.00 41.50
11 15 -0.00 44.91 0.00 3.49 -0.00 38.70
22 0.00 -5.77 -0.00 -3.29 -0.00 31.75
12 15 0.00 47.82 -0.00 7.40 0.00 47.04
22 -0.00 -8.68 0.00 -7.18 0.00 31.41
13 15 0.00 53.12 -0.00 4.08 -0.00 58.35
22 -0.00 -13.98 0.00 -3.82 0.00 34.67
14 15 -0.00 50.21 0.00 0.17 0.00 50.02
22 0.00 -11.07 -0.00 0.07 0.00 35.00
15 15 -0.00 28.29 0.00 2.33 -0.00 22.20
22 0.00 -2.50 -0.00 -2.21 -0.00 20.62

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 21 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 22

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

16 15 0.00 31.20 -0.00 6.24 0.00 30.54

22 -0.00 -5.41 0.00 -6.10 0.00 20.29
17 15 0.00 36.50 -0.00 2.92 -0.00 41.85
22 -0.00 -10.70 0.00 -2.74 0.00 23.54
18 15 -0.00 33.59 0.00 -0.99 0.00 33.52
22 0.00 -7.80 -0.00 1.15 0.00 23.88

22 7 16 0.00 10.61 0.00 0.47 0.00 6.90

24 -0.00 9.80 -0.00 -0.47 0.00 -5.74
8 16 0.00 11.93 0.00 0.93 0.00 7.41
24 -0.00 11.65 -0.00 -0.93 0.00 -7.01
11 16 0.00 0.27 0.00 0.82 0.00 -7.61
24 -0.00 19.12 -0.00 -0.82 0.00 -19.47
12 16 0.00 9.32 0.00 0.59 0.00 5.48
24 -0.00 10.07 -0.00 -0.59 0.00 -6.55
13 16 0.00 18.43 0.00 0.62 0.00 18.59
24 -0.00 0.97 -0.00 -0.62 0.00 6.51
14 16 0.00 9.38 0.00 0.85 0.00 5.50
24 -0.00 10.01 -0.00 -0.85 0.00 -6.41
15 16 0.00 -2.89 0.00 0.55 0.00 -9.56
24 -0.00 16.00 -0.00 -0.55 0.00 -17.59
16 16 0.00 6.16 0.00 0.32 0.00 3.53
24 -0.00 6.96 -0.00 -0.32 0.00 -4.67
17 16 0.00 15.27 0.00 0.36 0.00 16.64
24 -0.00 -2.15 -0.00 -0.36 0.00 8.40
18 16 0.00 6.22 0.00 0.58 0.00 3.56
24 -0.00 6.90 -0.00 -0.58 0.00 -4.53

23 7 17 1.08 131.90 2.38 2.55 -0.02 -0.96

20 -1.08 -120.52 -2.38 5.64 0.02 -2.79
8 17 0.78 138.19 2.55 2.85 -0.02 -0.53
20 -0.78 -128.44 -2.55 5.96 0.02 -2.18
11 17 -22.02 120.41 2.75 3.51 -0.40 46.16
20 22.02 -110.65 -2.75 5.98 0.40 29.81
12 17 5.05 110.80 -3.87 -10.39 -0.52 -9.30
20 -5.05 -101.05 3.87 -2.97 0.52 -8.12
13 17 27.24 121.65 1.74 1.46 -0.22 -54.71
20 -27.24 -111.89 -1.74 4.55 0.22 -39.29
14 17 0.11 131.25 8.36 15.36 -0.09 0.87
20 -0.11 -121.50 -8.36 13.50 0.09 -1.24
15 17 -22.21 84.29 2.08 2.75 -0.40 46.27
20 22.21 -76.97 -2.08 4.42 0.40 30.35
16 17 4.86 74.69 -4.54 -11.14 -0.52 -9.18
20 -4.86 -67.37 4.54 -4.53 0.52 -7.59
17 17 27.06 85.53 1.07 0.71 -0.22 -54.59
20 -27.06 -78.21 -1.07 2.99 0.22 -38.75

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 22 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 23

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

18 17 -0.08 95.13 7.69 14.60 -0.09 0.98

20 0.08 -87.82 -7.69 11.94 0.09 -0.70

24 7 18 -5.16 252.07 2.73 2.67 -0.02 6.04

21 5.16 -240.69 -2.73 6.74 0.02 11.76
8 18 -5.93 291.66 4.36 4.77 -0.02 6.95
21 5.93 -281.90 -4.36 10.27 0.02 13.50
11 18 -16.71 233.22 4.22 5.72 -0.40 27.94
21 16.71 -223.46 -4.22 8.84 0.40 29.71
12 18 -4.03 246.91 -12.10 -28.99 -0.52 3.95
21 4.03 -237.15 12.10 -12.76 0.52 9.97
13 18 7.47 246.37 1.88 0.76 -0.22 -17.53
21 -7.47 -236.61 -1.88 5.70 0.22 -8.24
14 18 -5.22 232.67 18.19 35.47 -0.09 6.49
21 5.22 -222.92 -18.19 27.29 0.09 11.51
15 18 -15.13 155.58 3.00 4.37 -0.40 26.09
21 15.13 -148.26 -3.00 5.99 0.40 26.12
16 18 -2.46 169.27 -13.32 -30.34 -0.52 2.10
21 2.46 -161.95 13.32 -15.60 0.52 6.38
17 18 9.04 168.73 0.66 -0.58 -0.22 -19.38
21 -9.04 -161.41 -0.66 2.86 0.22 -11.83
18 18 -3.64 155.03 16.98 34.12 -0.09 4.64
21 3.64 -147.72 -16.98 24.45 0.09 7.92

26 7 20 -0.00 40.39 0.00 -21.87 -0.00 -2.68

21 0.00 47.79 0.00 34.43 -0.00 2.68
8 20 -0.00 42.89 0.00 -24.14 0.00 -3.00
21 0.00 51.14 0.00 38.03 -0.00 3.00
11 20 0.00 37.78 0.00 -21.42 -0.00 -3.40
21 -0.00 43.57 0.00 31.12 -0.00 3.40
12 20 -0.00 29.49 0.00 -6.79 0.00 -2.32
21 0.00 51.86 0.00 45.92 0.00 2.32
13 20 -0.00 36.71 0.00 -19.57 0.00 -1.36
21 0.00 44.64 0.00 33.06 -0.00 1.36
14 20 0.00 45.00 0.00 -34.20 -0.00 -2.44
21 -0.00 36.35 0.00 18.26 -0.00 2.44
15 20 0.00 26.54 0.00 -15.05 -0.00 -2.61
21 -0.00 30.15 0.00 21.08 -0.00 2.61
16 20 -0.00 18.25 0.00 -0.42 -0.00 -1.53
21 0.00 38.44 0.00 35.88 0.00 1.53
17 20 -0.00 25.47 0.00 -13.20 0.00 -0.57
21 0.00 31.22 0.00 23.02 -0.00 0.57
18 20 0.00 33.77 0.00 -27.83 -0.00 -1.65
21 -0.00 22.92 0.00 8.22 -0.00 1.65

27 7 21 0.00 40.81 0.00 -45.83 0.00 2.38

54 -0.00 -5.27 0.00 -23.80 -0.00 -2.38

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 23 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 24

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

8 21 0.00 49.47 0.00 -55.45 0.00 2.74

54 -0.00 -5.62 0.00 -28.56 -0.00 -2.74
11 21 0.00 39.61 0.00 -44.80 0.00 0.56
54 -0.00 -4.97 0.00 -22.77 0.00 -0.56
12 21 -0.00 36.56 0.00 -35.98 -0.00 2.40
54 0.00 -1.92 0.00 -23.13 -0.00 -2.40
13 21 0.00 39.45 0.00 -43.99 0.00 4.01
54 -0.00 -4.80 0.00 -23.13 -0.00 -4.01
14 21 0.00 42.49 0.00 -52.81 0.00 2.17
54 -0.00 -7.85 0.00 -22.77 0.00 -2.17
15 21 0.00 26.33 0.00 -29.93 0.00 -0.17
54 -0.00 -3.49 0.00 -15.12 0.00 0.17
16 21 -0.00 23.29 0.00 -21.10 -0.00 1.67
54 0.00 -0.45 0.00 -15.48 -0.00 -1.67
17 21 0.00 26.17 0.00 -29.12 0.00 3.28
54 -0.00 -3.33 0.00 -15.48 -0.00 -3.28
18 21 0.00 29.21 0.00 -37.94 0.00 1.44
54 -0.00 -6.37 0.00 -15.12 0.00 -1.44

28 7 23 -0.03 132.54 -2.89 -3.70 -0.02 0.24

24 0.03 -121.15 2.89 -6.26 0.02 -0.13
8 23 -0.05 137.82 -5.23 -6.12 -0.02 0.28
24 0.05 -128.06 5.23 -11.94 0.02 -0.11
11 23 -13.54 119.66 -2.22 -1.54 -0.40 25.44
24 13.54 -109.91 2.22 -6.13 0.40 21.29
12 23 -0.86 125.80 -15.42 -32.70 -0.52 1.77
24 0.86 -116.05 15.42 -20.52 0.52 1.19
13 23 11.84 122.50 -4.24 -6.15 -0.22 -21.91
24 -11.84 -112.74 4.24 -8.47 0.22 -18.95
14 23 -0.82 116.36 8.96 25.00 -0.09 1.71
24 0.82 -106.60 -8.96 5.91 0.09 1.11
15 23 -13.53 83.69 -0.74 0.17 -0.40 25.36
24 13.53 -76.38 0.74 -2.73 0.40 21.32
16 23 -0.84 89.84 -13.94 -30.98 -0.52 1.69
24 0.84 -82.52 13.94 -17.12 0.52 1.21
17 23 11.86 86.53 -2.76 -4.43 -0.22 -21.98
24 -11.86 -79.21 2.76 -5.08 0.22 -18.92
18 23 -0.80 80.39 10.44 26.71 -0.09 1.64
24 0.80 -73.07 -10.44 9.31 0.09 1.14

29 7 26 0.00 29.09 0.00 -0.39 -0.00 -12.06

20 0.00 30.64 -0.00 0.39 -0.00 15.88
8 26 0.00 29.17 0.00 -0.43 -0.00 -12.43
20 0.00 30.32 -0.00 0.43 -0.00 16.17
11 26 0.00 39.36 -0.00 -0.52 -0.00 -29.84
20 0.00 14.43 0.00 0.52 -0.00 -5.18

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 24 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 25

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

12 26 0.00 23.60 0.00 -0.04 -0.00 -7.07

20 0.00 30.19 -0.00 0.04 0.00 18.28
13 26 0.00 11.19 0.00 -0.56 0.00 10.66
20 0.00 42.59 -0.00 0.56 0.00 36.96
14 26 0.00 26.96 -0.00 -1.04 0.00 -12.13
20 0.00 26.83 0.00 1.04 -0.00 13.49
15 26 0.00 31.80 -0.00 -0.41 -0.00 -26.60
20 0.00 6.59 0.00 0.41 -0.00 -9.38
16 26 0.00 16.04 0.00 0.07 -0.00 -3.83
20 0.00 22.35 -0.00 -0.07 0.00 14.08
17 26 0.00 3.63 0.00 -0.44 0.00 13.89
20 0.00 34.76 -0.00 0.44 0.00 32.76
18 26 0.00 19.40 -0.00 -0.92 0.00 -8.89
20 0.00 18.99 0.00 0.92 -0.00 9.29

30 7 22 0.00 -8.80 -0.00 5.71 0.00 -32.00

53 -0.00 9.39 0.00 -5.71 0.00 30.86
8 22 0.00 -9.98 -0.00 6.48 0.00 -38.75
53 -0.00 10.59 0.00 -6.48 0.00 37.46
11 22 -0.00 -12.43 0.00 5.27 -0.00 -31.18
53 0.00 12.97 -0.00 -5.27 -0.00 29.60
12 22 0.00 -12.56 0.00 6.00 -0.00 -29.01
53 -0.00 13.10 -0.00 -6.00 -0.00 27.41
13 22 -0.00 -4.38 -0.00 5.76 0.00 -30.65
53 0.00 4.92 0.00 -5.76 0.00 30.07
14 22 0.00 -4.25 0.00 5.03 -0.00 -32.82
53 -0.00 4.79 -0.00 -5.03 0.00 32.26
15 22 -0.00 -9.78 0.00 3.55 -0.00 -20.79
53 0.00 10.16 -0.00 -3.55 -0.00 19.54
16 22 0.00 -9.91 0.00 4.28 -0.00 -18.62
53 -0.00 10.29 -0.00 -4.28 -0.00 17.35
17 22 -0.00 -1.74 -0.00 4.04 0.00 -20.26
53 0.00 2.11 0.00 -4.04 0.00 20.02
18 22 0.00 -1.60 0.00 3.31 -0.00 -22.43
53 -0.00 1.98 -0.00 -3.31 0.00 22.20

31 7 24 -0.00 11.23 -0.00 -0.55 -0.00 6.24

30 0.00 10.28 0.00 0.55 -0.00 -4.81
8 24 -0.00 13.12 -0.00 -1.03 -0.00 7.52
30 0.00 11.74 0.00 1.03 -0.00 -5.43
11 24 -0.00 0.53 -0.00 -0.41 -0.00 -8.58
30 0.00 19.91 0.00 0.41 -0.00 -20.73
12 24 -0.00 10.09 -0.00 -0.21 -0.00 5.16
30 0.00 10.36 0.00 0.21 -0.00 -5.57
13 24 -0.00 19.60 -0.00 -0.58 -0.00 18.73
30 0.00 0.85 0.00 0.58 -0.00 9.62

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 25 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 26

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

14 24 -0.00 10.05 -0.00 -0.79 -0.00 5.00

30 0.00 10.40 0.00 0.79 -0.00 -5.53
15 24 -0.00 -2.97 -0.00 -0.12 -0.00 -10.60
30 0.00 16.80 0.00 0.12 -0.00 -19.29
16 24 -0.00 6.59 -0.00 0.08 -0.00 3.14
30 0.00 7.24 0.00 -0.08 -0.00 -4.13
17 24 -0.00 16.10 -0.00 -0.29 -0.00 16.72
30 0.00 -2.27 0.00 0.29 -0.00 11.06
18 24 -0.00 6.55 -0.00 -0.50 -0.00 2.98
30 0.00 7.28 0.00 0.50 -0.00 -4.09

32 7 21 0.00 36.25 0.00 -2.03 0.00 40.02

41 0.00 6.86 -0.00 2.03 -0.00 10.20
8 21 0.00 43.88 0.00 -2.23 -0.00 47.98
41 0.00 9.12 -0.00 2.23 -0.00 11.99
11 21 0.00 26.03 -0.00 -2.13 0.00 22.19
41 0.00 15.94 0.00 2.13 0.00 -2.35
12 21 0.00 35.81 0.00 -0.33 -0.00 40.32
41 0.00 6.17 -0.00 0.33 -0.00 10.31
13 21 0.00 44.60 0.00 -1.53 0.00 55.87
41 0.00 -2.63 -0.00 1.53 0.00 22.46
14 21 0.00 34.82 -0.00 -3.34 -0.00 37.74
41 0.00 7.15 0.00 3.34 -0.00 9.79
15 21 0.00 14.26 -0.00 -1.55 0.00 9.34
41 0.00 13.46 0.00 1.55 0.00 -5.55
16 21 0.00 24.04 0.00 0.26 -0.00 27.47
41 0.00 3.68 -0.00 -0.26 -0.00 7.11
17 21 0.00 32.83 0.00 -0.95 0.00 43.02
41 0.00 -5.11 -0.00 0.95 0.00 19.26
18 21 0.00 23.05 -0.00 -2.75 -0.00 24.89
41 0.00 4.67 0.00 2.75 -0.00 6.59

33 7 25 -1.49 105.84 3.44 3.52 -0.02 1.89

26 1.49 -94.46 -3.44 8.34 0.02 3.25
8 25 -1.52 103.20 3.66 3.99 -0.02 1.92
26 1.52 -93.45 -3.66 8.64 0.02 3.31
11 25 -11.65 110.12 1.80 0.68 -0.40 22.22
26 11.65 -100.36 -1.80 5.53 0.40 17.97
12 25 -1.37 82.40 -7.08 -20.56 -0.52 2.19
26 1.37 -72.64 7.08 -3.86 0.52 2.52
13 25 10.87 78.18 6.71 10.73 -0.22 -22.68
26 -10.87 -68.42 -6.71 12.40 0.22 -14.83
14 25 0.55 105.89 15.54 31.89 -0.09 -2.59
26 -0.55 -96.14 -15.54 21.71 0.09 0.68
15 25 -11.26 83.54 0.84 -0.38 -0.40 21.72
26 11.26 -76.22 -0.84 3.27 0.40 17.11

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 26 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 27

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

16 25 -0.97 55.82 -8.04 -21.62 -0.52 1.69

26 0.97 -48.50 8.04 -6.11 0.52 1.66
17 25 11.27 51.59 5.75 9.68 -0.22 -23.18
26 -11.27 -44.28 -5.75 10.15 0.22 -15.69
18 25 0.95 79.31 14.58 30.83 -0.09 -3.09
26 -0.95 -71.99 -14.58 19.46 0.09 -0.18

34 7 27 -5.47 151.52 -2.70 -3.42 -0.02 6.44

29 5.47 -140.14 2.70 -5.90 0.02 12.45
8 27 -6.68 166.65 -3.15 -3.69 -0.02 7.85
29 6.68 -156.90 3.15 -7.17 0.02 15.20
11 27 -17.50 135.08 0.05 2.25 -0.40 29.53
29 17.50 -125.32 -0.05 -2.07 0.40 30.86
12 27 -5.07 126.17 -16.01 -31.78 -0.52 6.02
29 5.07 -116.41 16.01 -23.45 0.52 11.48
13 27 6.15 148.92 -3.10 -4.18 -0.22 -15.64
29 -6.15 -139.17 3.10 -6.52 0.22 -5.58
14 27 -6.27 157.85 12.91 29.77 -0.09 7.85
29 6.27 -148.10 -12.91 14.78 0.09 13.78
15 27 -15.71 91.12 0.89 3.22 -0.40 27.42
29 15.71 -83.80 -0.89 -0.14 0.40 26.78
16 27 -3.28 82.21 -15.17 -30.82 -0.52 3.92
29 3.28 -74.89 15.17 -21.52 0.52 7.40
17 27 7.94 104.96 -2.27 -3.22 -0.22 -17.75
29 -7.94 -97.65 2.27 -4.60 0.22 -9.66
18 27 -4.47 113.89 13.75 30.74 -0.09 5.74
29 4.47 -106.57 -13.75 16.70 0.09 9.69

35 7 28 -1.15 101.38 -0.32 -0.72 -0.02 1.52

30 1.15 -90.00 0.32 -0.40 0.02 2.46
8 28 -1.43 94.77 -0.59 -0.78 -0.02 1.86
30 1.43 -85.02 0.59 -1.24 0.02 3.07
11 28 -13.46 95.07 1.66 4.08 -0.40 25.34
30 13.46 -85.31 -1.66 1.65 0.40 21.09
12 28 -1.82 110.15 -11.82 -27.03 -0.52 2.87
30 1.82 -100.40 11.82 -13.75 0.52 3.40
13 28 9.69 82.34 -0.51 -1.24 -0.22 -19.44
30 -9.69 -72.59 0.51 -0.51 0.22 -13.98
14 28 -1.93 67.26 12.93 29.79 -0.09 2.98
30 1.93 -57.50 -12.93 14.82 0.09 3.67
15 28 -13.07 70.88 1.83 4.28 -0.40 24.84
30 13.07 -63.56 -1.83 2.02 0.40 20.27
16 28 -1.43 85.97 -11.65 -26.82 -0.52 2.37
30 1.43 -78.65 11.65 -13.38 0.52 2.58
17 28 10.07 58.16 -0.34 -1.03 -0.22 -19.94
30 -10.07 -50.84 0.34 -0.14 0.22 -14.80

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 27 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 28

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

18 28 -1.54 43.07 13.10 30.00 -0.09 2.48

30 1.54 -35.76 -13.10 15.18 0.09 2.84

37 7 32 -0.00 37.09 -0.00 24.96 -0.00 -6.95

26 0.00 35.74 0.00 -20.13 -0.00 5.57
8 32 -0.00 36.08 -0.00 24.70 -0.00 -6.59
26 0.00 35.69 0.00 -20.77 -0.00 5.47
11 32 0.00 34.33 0.00 24.46 0.00 -6.99
26 -0.00 31.02 -0.00 -16.15 -0.00 4.62
12 32 0.00 39.67 0.00 33.48 0.00 -9.66
26 -0.00 25.68 -0.00 -6.21 0.00 1.89
13 32 -0.00 30.66 -0.00 18.15 -0.00 -4.87
26 0.00 34.68 0.00 -22.84 -0.00 6.21
14 32 -0.00 25.33 -0.00 9.14 -0.00 -2.20
26 0.00 40.01 0.00 -32.77 0.00 8.94
15 32 0.00 25.04 0.00 18.08 0.00 -5.30
26 -0.00 21.78 -0.00 -10.74 -0.00 3.21
16 32 0.00 30.38 0.00 27.10 0.00 -7.97
26 -0.00 16.44 -0.00 -0.80 0.00 0.48
17 32 -0.00 21.38 -0.00 11.77 -0.00 -3.18
26 0.00 25.44 0.00 -17.42 -0.00 4.80
18 32 -0.00 16.04 -0.00 2.76 -0.00 -0.52
26 0.00 30.78 0.00 -27.35 0.00 7.53

38 7 31 -2.45 178.95 1.53 1.36 -0.02 3.02

32 2.45 -167.57 -1.53 3.91 0.02 5.44
8 31 -3.08 178.99 1.73 1.81 -0.02 3.73
32 3.08 -169.23 -1.73 4.16 0.02 6.89
11 31 -13.12 176.85 0.10 -1.09 -0.40 24.46
32 13.12 -167.09 -0.10 1.43 0.40 20.82
12 31 -3.50 158.57 -10.72 -24.49 -0.52 5.34
32 3.50 -148.81 10.72 -12.50 0.52 6.72
13 31 9.32 145.40 5.53 9.49 -0.22 -20.60
32 -9.32 -135.65 -5.53 9.58 0.22 -11.54
14 31 -0.33 163.68 16.29 32.79 -0.09 -1.44
32 0.33 -153.93 -16.29 23.43 0.09 2.59
15 31 -12.29 130.50 -0.36 -1.58 -0.40 23.46
32 12.29 -123.19 0.36 0.34 0.40 18.95
16 31 -2.66 112.22 -11.18 -24.98 -0.52 4.34
32 2.66 -104.90 11.18 -13.59 0.52 4.85
17 31 10.15 99.06 5.07 9.00 -0.22 -21.60
32 -10.15 -91.74 -5.07 8.50 0.22 -13.41
18 31 0.50 117.34 15.84 32.30 -0.09 -2.45
32 -0.50 -110.02 -15.84 22.34 0.09 0.73

40 7 32 0.00 38.11 0.00 -27.54 -0.00 9.13

45 -0.00 8.85 -0.00 -12.99 -0.00 2.42

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 28 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 29

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

8 32 0.00 35.32 0.00 -25.79 -0.00 9.00

45 -0.00 7.53 -0.00 -12.68 -0.00 1.97
11 32 0.00 32.33 0.00 -22.11 0.00 7.94
45 -0.00 8.73 -0.00 -10.58 0.00 1.38
12 32 -0.00 29.58 -0.00 -15.77 -0.00 5.83
45 0.00 11.48 0.00 -9.27 -0.00 1.31
13 32 -0.00 35.47 -0.00 -28.13 0.00 9.21
45 0.00 5.59 0.00 -13.24 -0.00 2.58
14 32 0.00 38.22 0.00 -34.46 -0.00 11.32
45 -0.00 2.84 -0.00 -14.54 -0.00 2.65
15 32 0.00 23.34 0.00 -15.52 0.00 5.62
45 -0.00 6.85 -0.00 -7.31 0.00 0.89
16 32 -0.00 20.58 -0.00 -9.19 -0.00 3.50
45 0.00 9.61 0.00 -6.01 -0.00 0.83
17 32 -0.00 26.47 -0.00 -21.55 0.00 6.88
45 0.00 3.71 0.00 -9.97 -0.00 2.10
18 32 0.00 29.23 0.00 -27.88 -0.00 9.00
45 -0.00 0.96 -0.00 -11.27 -0.00 2.16

41 7 30 0.00 3.21 0.00 0.20 0.00 2.14

36 -0.00 2.39 -0.00 -0.20 0.00 -0.97
8 30 0.00 2.89 0.00 0.11 0.00 2.16
36 -0.00 1.92 -0.00 -0.11 0.00 -0.79
11 30 0.00 -4.53 0.00 0.30 0.00 -7.67
36 -0.00 9.34 -0.00 -0.30 0.00 -11.99
12 30 0.00 2.47 0.00 0.34 0.00 1.41
36 -0.00 2.34 -0.00 -0.34 0.00 -1.22
13 30 0.00 9.20 0.00 0.20 0.00 10.33
36 -0.00 -4.39 -0.00 -0.20 0.00 8.92
14 30 0.00 2.20 0.00 0.16 0.00 1.25
36 -0.00 2.61 -0.00 -0.16 0.00 -1.84
15 30 0.00 -5.26 0.00 0.28 0.00 -8.23
36 -0.00 8.87 -0.00 -0.28 0.00 -11.80
16 30 0.00 1.74 0.00 0.31 0.00 0.85
36 -0.00 1.86 -0.00 -0.31 0.00 -1.03
17 30 0.00 8.47 0.00 0.18 0.00 9.77
36 -0.00 -4.86 -0.00 -0.18 0.00 9.12
18 30 0.00 1.47 0.00 0.14 0.00 0.69
36 -0.00 2.14 -0.00 -0.14 0.00 -1.65

42 7 33 -0.55 104.20 -2.94 -3.71 -0.02 0.87

34 0.55 -92.82 2.94 -6.44 0.02 1.03
8 33 -0.39 89.19 -2.71 -3.23 -0.02 0.68
34 0.39 -79.44 2.71 -6.11 0.02 0.68
11 33 -11.07 100.30 -4.07 -5.63 -0.40 22.78
34 11.07 -90.54 4.07 -8.40 0.40 15.41

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 29 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 30

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

12 33 -2.84 80.94 -14.29 -28.29 -0.52 5.47

34 2.84 -71.19 14.29 -21.01 0.52 4.32
13 33 10.14 80.75 1.87 5.44 -0.22 -21.17
34 -10.14 -71.00 -1.87 1.02 0.22 -13.82
14 33 1.91 100.11 12.04 27.99 -0.09 -3.86
34 -1.91 -90.35 -12.04 13.54 0.09 -2.74
15 33 -10.98 78.01 -3.38 -4.82 -0.40 22.61
34 10.98 -70.69 3.38 -6.83 0.40 15.26
16 33 -2.74 58.65 -13.60 -27.48 -0.52 5.30
34 2.74 -51.33 13.60 -19.45 0.52 4.17
17 33 10.24 58.46 2.56 6.25 -0.22 -21.34
34 -10.24 -51.15 -2.56 2.59 0.22 -13.98
18 33 2.01 77.82 12.73 28.80 -0.09 -4.03
34 -2.01 -70.50 -12.73 15.10 0.09 -2.89

43 7 36 -0.00 19.46 -0.00 8.07 0.00 -2.02

34 0.00 22.55 0.00 -12.40 0.00 3.25
8 36 -0.00 16.37 -0.00 6.57 0.00 -1.56
34 0.00 19.64 0.00 -11.15 0.00 2.87
11 36 -0.00 18.54 -0.00 9.51 0.00 -2.97
34 0.00 17.48 0.00 -8.02 0.00 2.55
12 36 -0.00 26.60 -0.00 21.19 0.00 -5.99
34 0.00 9.42 0.00 2.92 0.00 -0.89
13 36 -0.00 12.54 -0.00 0.98 0.00 0.20
34 0.00 23.47 0.00 -16.33 0.00 4.18
14 36 -0.00 4.48 -0.00 -10.69 0.00 3.21
34 0.00 31.53 0.00 -27.26 0.00 7.61
15 36 -0.00 14.46 -0.00 7.89 0.00 -2.59
34 0.00 12.55 0.00 -5.20 0.00 1.83
16 36 -0.00 22.52 -0.00 19.57 0.00 -5.61
34 0.00 4.49 0.00 5.74 0.00 -1.61
17 36 -0.00 8.46 -0.00 -0.64 0.00 0.58
34 0.00 18.55 0.00 -13.51 0.00 3.46
18 36 -0.00 0.41 -0.00 -12.31 0.00 3.59
34 0.00 26.60 0.00 -24.44 0.00 6.89

44 7 35 -0.69 53.33 -1.61 -2.19 -0.02 1.06

36 0.69 -41.95 1.61 -3.38 0.02 1.32
8 35 -0.55 45.19 -1.29 -1.61 -0.02 0.89
36 0.55 -35.43 1.29 -2.83 0.02 1.02
11 35 -10.99 55.47 -2.49 -3.72 -0.40 23.14
36 10.99 -45.72 2.49 -4.87 0.40 14.79
12 35 -3.19 59.45 -11.47 -24.92 -0.52 6.45
36 3.19 -49.70 11.47 -14.64 0.52 4.56
13 35 9.09 33.85 2.60 6.34 -0.22 -19.72
36 -9.09 -24.10 -2.60 2.63 0.22 -11.64

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 30 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 31

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

14 35 1.30 29.86 11.52 27.43 -0.09 -3.06

36 -1.30 -20.11 -11.52 12.30 0.09 -1.43
15 35 -10.86 44.21 -2.17 -3.33 -0.40 22.91
36 10.86 -36.89 2.17 -4.17 0.40 14.55
16 35 -3.06 48.19 -11.15 -24.53 -0.52 6.23
36 3.06 -40.87 11.15 -13.94 0.52 4.31
17 35 9.23 22.59 2.92 6.73 -0.22 -19.94
36 -9.23 -15.27 -2.92 3.33 0.22 -11.88
18 35 1.44 18.60 11.83 27.82 -0.09 -3.29
36 -1.44 -11.28 -11.83 13.00 0.09 -1.68

46 7 16 -0.00 28.26 0.00 -13.38 -0.00 -0.00

38 0.00 -20.70 0.00 0.53 -0.00 0.00
8 16 -0.00 24.22 0.00 -11.33 -0.00 -0.00
38 0.00 -17.74 0.00 0.32 -0.00 0.00
11 16 -0.00 24.22 0.00 -11.21 -0.00 -0.00
38 0.00 -17.74 0.00 0.19 -0.00 0.00
12 16 0.00 24.22 0.00 -11.35 -0.00 -0.00
38 -0.00 -17.74 0.00 0.34 -0.00 0.00
13 16 0.00 24.22 0.00 -11.39 0.00 -0.00
38 -0.00 -17.74 0.00 0.37 0.00 0.00
14 16 0.00 24.22 0.00 -11.25 0.00 -0.00
38 -0.00 -17.74 0.00 0.23 0.00 0.00
15 16 -0.00 18.17 0.00 -8.38 -0.00 -0.00
38 0.00 -13.31 0.00 0.12 -0.00 0.00
16 16 0.00 18.17 0.00 -8.53 -0.00 -0.00
38 -0.00 -13.31 0.00 0.26 -0.00 0.00
17 16 0.00 18.17 0.00 -8.57 0.00 -0.00
38 -0.00 -13.31 0.00 0.30 0.00 0.00
18 16 0.00 18.17 0.00 -8.42 0.00 -0.00
38 -0.00 -13.31 0.00 0.16 0.00 0.00

47 7 24 -0.00 66.20 0.00 -30.46 -0.00 -0.04

39 0.00 -64.81 0.00 -3.93 -0.00 0.04
8 24 -0.00 62.76 0.00 -30.09 -0.00 0.00
39 0.00 -61.58 0.00 -2.55 -0.00 -0.00
11 24 -0.00 58.30 0.00 -27.23 -0.00 9.82
39 0.00 -57.12 0.00 -3.07 0.00 -9.82
12 24 0.00 57.70 0.00 -26.65 0.00 0.71
39 -0.00 -56.52 0.00 -3.34 0.00 -0.71
13 24 0.00 58.93 0.00 -27.47 0.00 -8.40
39 -0.00 -57.74 0.00 -3.15 0.00 8.40
14 24 -0.00 59.53 0.00 -28.06 -0.00 0.76
39 0.00 -58.34 0.00 -2.88 -0.00 -0.76
15 24 -0.00 42.24 0.00 -19.46 -0.00 9.82
39 0.00 -41.35 0.00 -2.48 0.00 -9.82

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 31 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 32

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

16 24 0.00 41.64 0.00 -18.87 0.00 0.70

39 -0.00 -40.75 0.00 -2.75 0.00 -0.70
17 24 0.00 42.86 0.00 -19.70 0.00 -8.40
39 -0.00 -41.97 0.00 -2.57 0.00 8.40
18 24 -0.00 43.46 0.00 -20.29 -0.00 0.75
39 0.00 -42.57 0.00 -2.30 -0.00 -0.75

48 7 30 -0.00 29.34 0.00 -13.80 -0.00 -0.00

40 0.00 -21.78 0.00 0.39 -0.00 0.00
8 30 -0.00 25.15 0.00 -11.65 -0.00 -0.00
40 0.00 -18.67 0.00 0.15 -0.00 0.00
11 30 -0.00 25.15 0.00 -11.97 -0.00 -0.00
40 0.00 -18.67 0.00 0.47 -0.00 0.00
12 30 -0.00 25.15 0.00 -12.10 -0.00 -0.00
40 0.00 -18.67 0.00 0.60 -0.00 0.00
13 30 -0.00 25.15 0.00 -11.84 -0.00 -0.00
40 0.00 -18.67 0.00 0.33 -0.00 0.00
14 30 -0.00 25.15 0.00 -11.71 -0.00 -0.00
40 0.00 -18.67 0.00 0.21 -0.00 0.00
15 30 -0.00 18.86 0.00 -9.07 -0.00 -0.00
40 0.00 -14.00 0.00 0.45 -0.00 0.00
16 30 -0.00 18.86 0.00 -9.19 -0.00 -0.00
40 0.00 -14.00 0.00 0.57 -0.00 0.00
17 30 -0.00 18.86 0.00 -8.93 -0.00 -0.00
40 0.00 -14.00 0.00 0.31 -0.00 0.00
18 30 -0.00 18.86 0.00 -8.81 -0.00 -0.00
40 0.00 -14.00 0.00 0.18 -0.00 0.00

49 7 38 0.00 20.70 0.00 -0.53 0.00 -0.00

39 -0.00 20.70 -0.00 0.53 0.00 0.00
8 38 0.00 17.74 0.00 -0.32 0.00 -0.00
39 -0.00 17.74 -0.00 0.32 0.00 0.00
11 38 0.00 17.74 0.00 -0.19 0.00 -0.00
39 -0.00 17.74 -0.00 0.19 0.00 0.00
12 38 0.00 17.74 0.00 -0.34 0.00 -0.00
39 -0.00 17.74 -0.00 0.34 0.00 0.00
13 38 0.00 17.74 0.00 -0.37 0.00 -0.00
39 -0.00 17.74 -0.00 0.37 0.00 0.00
14 38 0.00 17.74 0.00 -0.23 0.00 -0.00
39 -0.00 17.74 -0.00 0.23 0.00 0.00
15 38 0.00 13.31 0.00 -0.12 0.00 -0.00
39 -0.00 13.31 -0.00 0.12 0.00 0.00
16 38 0.00 13.31 0.00 -0.26 0.00 -0.00
39 -0.00 13.31 -0.00 0.26 0.00 0.00
17 38 0.00 13.31 0.00 -0.30 0.00 -0.00
39 -0.00 13.31 -0.00 0.30 0.00 0.00

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 32 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 33

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

18 38 0.00 13.31 0.00 -0.16 0.00 -0.00

39 -0.00 13.31 -0.00 0.16 0.00 0.00

50 7 39 -0.00 21.78 -0.00 0.39 -0.00 0.00

40 0.00 21.78 0.00 -0.39 -0.00 -0.00
8 39 -0.00 18.67 -0.00 0.15 -0.00 0.00
40 0.00 18.67 0.00 -0.15 -0.00 -0.00
11 39 -0.00 18.67 -0.00 0.47 -0.00 0.00
40 0.00 18.67 0.00 -0.47 -0.00 -0.00
12 39 -0.00 18.67 -0.00 0.60 -0.00 0.00
40 0.00 18.67 0.00 -0.60 -0.00 -0.00
13 39 -0.00 18.67 -0.00 0.33 -0.00 0.00
40 0.00 18.67 0.00 -0.33 -0.00 -0.00
14 39 -0.00 18.67 -0.00 0.21 -0.00 0.00
40 0.00 18.67 0.00 -0.21 -0.00 -0.00
15 39 -0.00 14.00 -0.00 0.45 -0.00 0.00
40 0.00 14.00 0.00 -0.45 -0.00 -0.00
16 39 -0.00 14.00 -0.00 0.57 -0.00 0.00
40 0.00 14.00 0.00 -0.57 -0.00 -0.00
17 39 -0.00 14.00 -0.00 0.31 -0.00 0.00
40 0.00 14.00 0.00 -0.31 -0.00 -0.00
18 39 -0.00 14.00 -0.00 0.18 -0.00 0.00
40 0.00 14.00 0.00 -0.18 -0.00 -0.00

51 7 41 0.00 -27.28 -0.00 8.22 0.00 -9.35

32 0.00 35.11 0.00 -8.22 0.00 -15.40
8 41 0.00 -33.46 -0.00 10.16 0.00 -11.01
32 0.00 42.76 0.00 -10.16 0.00 -19.21
11 41 0.00 -36.97 -0.00 9.99 -0.00 1.96
32 0.00 44.50 0.00 -9.99 0.00 -34.29
12 41 0.00 -22.56 -0.00 3.25 0.00 -9.59
32 0.00 30.08 0.00 -3.25 0.00 -11.28
13 41 0.00 -16.06 0.00 7.02 -0.00 -20.55
32 0.00 23.58 -0.00 -7.02 -0.00 4.86
14 41 0.00 -30.48 -0.00 13.75 0.00 -9.01
32 0.00 38.00 0.00 -13.75 0.00 -18.16
15 41 0.00 -27.98 -0.00 7.25 -0.00 4.90
32 0.00 33.01 0.00 -7.25 0.00 -29.12
16 41 0.00 -13.56 -0.00 0.52 0.00 -6.65
32 0.00 18.60 0.00 -0.52 0.00 -6.10
17 41 0.00 -7.07 0.00 4.28 -0.00 -17.61
32 0.00 12.10 -0.00 -4.28 -0.00 10.04
18 41 0.00 -21.48 -0.00 11.02 0.00 -6.07
32 0.00 26.51 0.00 -11.02 0.00 -12.98

53 7 41 -0.00 20.42 0.00 -10.25 0.00 -0.85

43 0.00 6.37 0.00 -9.53 0.00 0.85

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 33 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 34

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

8 41 -0.00 24.33 0.00 -12.39 0.00 -0.97

43 0.00 7.88 0.00 -10.83 0.00 0.97
11 41 0.00 21.03 0.00 -12.12 -0.00 0.40
43 -0.00 4.82 0.00 -10.66 0.00 -0.40
12 41 -0.00 16.39 0.00 -3.58 -0.00 -0.72
43 0.00 9.46 0.00 -6.33 -0.00 0.72
13 41 0.00 18.69 0.00 -8.55 0.00 -1.90
43 -0.00 7.17 0.00 -7.72 0.00 1.90
14 41 -0.00 23.33 0.00 -17.09 0.00 -0.78
43 0.00 2.53 0.00 -12.06 0.00 0.78
15 41 0.00 14.52 0.00 -8.80 -0.00 0.66
43 -0.00 2.70 0.00 -7.79 0.00 -0.66
16 41 -0.00 9.88 0.00 -0.26 -0.00 -0.46
43 0.00 7.34 0.00 -3.45 -0.00 0.46
17 41 0.00 12.18 0.00 -5.23 0.00 -1.64
43 -0.00 5.05 0.00 -4.85 0.00 1.64
18 41 -0.00 16.81 0.00 -13.77 0.00 -0.52
43 0.00 0.41 0.00 -9.18 0.00 0.52

54 7 43 -0.00 -21.42 0.00 13.01 -0.00 -0.86

51 0.00 24.32 0.00 12.15 -0.00 0.86
8 43 -0.00 -25.70 0.00 15.58 -0.00 -0.99
51 0.00 28.19 0.00 14.06 -0.00 0.99
11 43 -0.00 -19.26 0.00 12.72 -0.00 0.39
51 0.00 21.75 0.00 9.83 -0.00 -0.39
12 43 -0.00 -23.90 0.00 9.55 0.00 -0.73
51 0.00 26.38 0.00 18.11 0.00 0.73
13 43 0.00 -21.60 0.00 12.75 -0.00 -1.92
51 -0.00 24.09 0.00 12.38 0.00 1.92
14 43 -0.00 -16.96 0.00 15.92 -0.00 -0.79
51 0.00 19.45 0.00 4.11 -0.00 0.79
15 43 -0.00 -12.37 0.00 8.55 -0.00 0.65
51 0.00 14.24 0.00 6.08 -0.00 -0.65
16 43 -0.00 -17.01 0.00 5.38 0.00 -0.47
51 0.00 18.88 0.00 14.36 0.00 0.47
17 43 0.00 -14.72 0.00 8.58 -0.00 -1.65
51 -0.00 16.59 0.00 8.64 0.00 1.65
18 43 0.00 -10.08 0.00 11.75 -0.00 -0.53
51 -0.00 11.95 0.00 0.36 -0.00 0.53

55 7 43 -0.00 4.92 0.00 -0.46 0.00 0.00

45 0.00 4.47 -0.00 0.46 -0.00 -0.00
8 43 -0.00 5.81 0.00 -1.18 0.00 0.00
45 0.00 5.21 -0.00 1.18 -0.00 -0.00
11 43 -0.00 4.72 0.00 0.73 -0.00 -0.00
45 0.00 4.26 -0.00 -0.73 -0.00 0.00

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 34 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 35

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

12 43 -0.00 4.72 -0.00 -0.64 0.00 0.00

45 0.00 4.26 0.00 0.64 0.00 -0.00
13 43 -0.00 4.72 0.00 -2.04 -0.00 0.01
45 0.00 4.26 -0.00 2.04 -0.00 -0.01
14 43 -0.00 4.72 0.00 -0.67 0.00 0.00
45 0.00 4.26 -0.00 0.67 -0.00 -0.00
15 43 -0.00 3.17 0.00 1.07 -0.00 -0.00
45 0.00 2.87 -0.00 -1.07 -0.00 0.00
16 43 -0.00 3.17 -0.00 -0.29 0.00 0.00
45 0.00 2.87 0.00 0.29 0.00 -0.00
17 43 -0.00 3.17 0.00 -1.69 -0.00 0.00
45 0.00 2.87 -0.00 1.69 -0.00 -0.00
18 43 -0.00 3.17 0.00 -0.33 0.00 0.00
45 0.00 2.87 -0.00 0.33 -0.00 -0.00

56 7 45 0.00 -13.32 -0.00 12.53 -0.00 -2.42

34 -0.00 36.88 0.00 26.97 -0.00 -8.84
8 45 0.00 -12.74 -0.00 11.50 -0.00 -1.96
34 -0.00 32.94 0.00 24.44 -0.00 -8.28
11 45 -0.00 -12.99 -0.00 11.31 -0.00 -1.38
34 0.00 33.19 0.00 25.03 -0.00 -8.98
12 45 0.00 -15.75 -0.00 8.63 -0.00 -1.31
34 -0.00 35.94 0.00 32.04 0.00 -10.28
13 45 -0.00 -9.86 -0.00 11.20 -0.00 -2.58
34 0.00 30.05 0.00 20.20 -0.00 -6.37
14 45 -0.00 -7.10 0.00 13.87 0.00 -2.65
34 0.00 27.30 -0.00 13.20 -0.00 -5.07
15 45 -0.00 -9.72 -0.00 8.38 -0.00 -0.89
34 0.00 24.87 0.00 18.83 -0.00 -6.87
16 45 0.00 -12.48 -0.00 5.71 -0.00 -0.83
34 -0.00 27.63 0.00 25.85 0.00 -8.17
17 45 -0.00 -6.59 -0.00 8.28 -0.00 -2.09
34 0.00 21.74 0.00 14.01 -0.00 -4.26
18 45 -0.00 -3.83 0.00 10.95 0.00 -2.16
34 0.00 18.98 -0.00 7.00 -0.00 -2.96

57 7 5 0.00 9.25 0.00 7.25 -0.00 0.00

46 -0.00 -6.81 0.00 0.17 -0.00 0.00
8 5 0.00 10.00 0.00 8.09 -0.00 0.00
46 -0.00 -7.91 0.00 0.19 -0.00 0.00
11 5 -0.00 8.57 0.00 6.89 0.00 0.00
46 0.00 -6.48 0.00 0.07 0.00 0.00
12 5 0.00 8.57 0.00 6.92 -0.00 0.00
46 -0.00 -6.48 0.00 0.04 -0.00 0.00
13 5 -0.00 8.57 0.00 6.86 0.00 0.00
46 0.00 -6.48 0.00 0.10 0.00 0.00

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 35 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 36

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

14 5 0.00 8.57 0.00 6.83 -0.00 0.00

46 -0.00 -6.48 0.00 0.13 -0.00 0.00
15 5 -0.00 5.94 0.00 4.75 0.00 0.00
46 0.00 -4.38 0.00 0.02 0.00 0.00
16 5 0.00 5.94 0.00 4.79 -0.00 0.00
46 -0.00 -4.38 0.00 -0.01 -0.00 0.00
17 5 -0.00 5.94 0.00 4.72 0.00 0.00
46 0.00 -4.38 0.00 0.05 0.00 0.00
18 5 0.00 5.94 0.00 4.69 -0.00 0.00
46 -0.00 -4.38 0.00 0.08 -0.00 0.00

58 7 13 0.00 16.58 0.00 15.31 -0.00 -0.00

47 -0.00 -14.13 0.00 -1.11 -0.00 0.00
8 13 0.00 18.53 0.00 17.49 -0.00 -0.00
47 -0.00 -16.44 0.00 -1.32 -0.00 0.00
11 13 -0.00 15.56 0.00 14.49 0.00 0.00
47 0.00 -13.47 0.00 -1.07 0.00 -0.00
12 13 0.00 15.56 0.00 14.84 -0.00 -0.00
47 -0.00 -13.47 0.00 -1.42 -0.00 0.00
13 13 -0.00 15.56 0.00 14.49 0.00 -0.00
47 0.00 -13.47 0.00 -1.07 0.00 0.00
14 13 0.00 15.56 0.00 14.14 -0.00 -0.00
47 -0.00 -13.47 0.00 -0.72 -0.00 0.00
15 13 -0.00 10.66 0.00 9.85 0.00 0.00
47 0.00 -9.09 0.00 -0.72 0.00 -0.00
16 13 0.00 10.66 0.00 10.20 -0.00 -0.00
47 -0.00 -9.09 0.00 -1.07 -0.00 0.00
17 13 -0.00 10.66 0.00 9.84 0.00 -0.00
47 0.00 -9.09 0.00 -0.71 0.00 0.00
18 13 0.00 10.66 0.00 9.49 -0.00 -0.00
47 -0.00 -9.09 0.00 -0.36 -0.00 0.00

59 7 47 0.00 6.81 -0.00 0.17 -0.00 0.00

46 0.00 6.81 0.00 -0.17 -0.00 0.00
8 47 0.00 7.91 -0.00 0.19 -0.00 0.00
46 0.00 7.91 0.00 -0.19 -0.00 0.00
11 47 0.00 6.48 -0.00 0.07 -0.00 0.00
46 0.00 6.48 0.00 -0.07 -0.00 0.00
12 47 0.00 6.48 -0.00 0.04 -0.00 0.00
46 0.00 6.48 0.00 -0.04 -0.00 0.00
13 47 0.00 6.48 -0.00 0.10 -0.00 0.00
46 0.00 6.48 0.00 -0.10 -0.00 0.00
14 47 0.00 6.48 -0.00 0.13 0.00 0.00
46 0.00 6.48 0.00 -0.13 -0.00 0.00
15 47 0.00 4.38 -0.00 0.02 -0.00 0.00
46 0.00 4.38 0.00 -0.02 -0.00 0.00

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 36 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 37

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

16 47 0.00 4.38 -0.00 -0.01 -0.00 0.00

46 0.00 4.38 0.00 0.01 -0.00 0.00
17 47 0.00 4.38 -0.00 0.05 -0.00 0.00
46 0.00 4.38 0.00 -0.05 -0.00 0.00
18 47 0.00 4.38 -0.00 0.08 0.00 0.00
46 0.00 4.38 0.00 -0.08 -0.00 0.00

60 7 48 0.00 6.93 0.00 0.13 0.00 0.00

49 0.00 6.93 -0.00 -0.13 0.00 0.00
8 48 0.00 8.19 0.00 0.13 0.00 0.00
49 0.00 8.19 -0.00 -0.13 0.00 0.00
11 48 0.00 6.64 0.00 0.02 -0.00 0.00
49 0.00 6.64 -0.00 -0.02 -0.00 0.00
12 48 0.00 6.64 0.00 -0.36 0.00 0.00
49 0.00 6.64 -0.00 0.36 0.00 0.00
13 48 0.00 6.64 -0.00 0.06 0.00 0.00
49 0.00 6.64 0.00 -0.06 0.00 0.00
14 48 0.00 6.64 0.00 0.44 0.00 0.00
49 0.00 6.64 -0.00 -0.44 0.00 0.00
15 48 0.00 4.46 0.00 -0.01 -0.00 0.00
49 0.00 4.46 -0.00 0.01 -0.00 0.00
16 48 0.00 4.46 0.00 -0.39 0.00 0.00
49 0.00 4.46 -0.00 0.39 0.00 0.00
17 48 0.00 4.46 -0.00 0.02 0.00 0.00
49 0.00 4.46 0.00 -0.02 0.00 0.00
18 48 0.00 4.46 0.00 0.40 0.00 0.00
49 0.00 4.46 -0.00 -0.40 0.00 0.00

61 7 20 0.00 9.77 0.00 9.11 -0.00 0.00

48 -0.00 -6.93 0.00 -0.13 -0.00 0.00
8 20 0.00 10.62 0.00 10.24 -0.00 0.00
48 -0.00 -8.19 0.00 -0.13 -0.00 0.00
11 20 0.00 9.08 0.00 8.47 -0.00 0.00
48 -0.00 -6.64 0.00 -0.02 -0.00 0.00
12 20 0.00 9.08 0.00 8.09 -0.00 0.00
48 -0.00 -6.64 0.00 0.36 -0.00 0.00
13 20 0.00 9.08 0.00 8.51 -0.00 0.00
48 -0.00 -6.64 0.00 -0.06 -0.00 0.00
14 20 0.00 9.08 0.00 8.89 -0.00 0.00
48 -0.00 -6.64 0.00 -0.44 -0.00 0.00
15 20 0.00 6.28 0.00 5.76 -0.00 0.00
48 -0.00 -4.46 0.00 0.01 -0.00 0.00
16 20 0.00 6.28 0.00 5.38 -0.00 0.00
48 -0.00 -4.46 0.00 0.39 -0.00 0.00
17 20 0.00 6.28 0.00 5.79 -0.00 0.00
48 -0.00 -4.46 0.00 -0.02 -0.00 0.00

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 37 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 38

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

18 20 0.00 6.28 0.00 6.18 -0.00 0.00

48 -0.00 -4.46 0.00 -0.40 -0.00 0.00

62 7 47 0.00 7.33 0.00 0.94 -0.00 0.00

49 -0.00 -6.93 0.00 0.13 -0.00 0.00
8 47 0.00 8.53 0.00 1.12 -0.00 0.00
49 -0.00 -8.19 0.00 0.13 -0.00 0.00
11 47 0.00 6.98 0.00 1.00 -0.00 0.00
49 -0.00 -6.64 0.00 0.02 -0.00 0.00
12 47 0.00 6.98 0.00 1.38 -0.00 0.00
49 -0.00 -6.64 0.00 -0.36 -0.00 0.00
13 47 0.00 6.98 0.00 0.97 -0.00 0.00
49 -0.00 -6.64 0.00 0.06 -0.00 0.00
14 47 0.00 6.98 0.00 0.58 -0.00 0.00
49 -0.00 -6.64 0.00 0.44 -0.00 0.00
15 47 0.00 4.71 0.00 0.70 -0.00 0.00
49 -0.00 -4.46 0.00 -0.01 -0.00 0.00
16 47 0.00 4.71 0.00 1.08 -0.00 0.00
49 -0.00 -4.46 0.00 -0.39 -0.00 0.00
17 47 0.00 4.71 0.00 0.66 -0.00 0.00
49 -0.00 -4.46 0.00 0.02 -0.00 0.00
18 47 0.00 4.71 0.00 0.28 -0.00 0.00
49 -0.00 -4.46 0.00 0.40 -0.00 0.00

63 7 50 0.00 -17.55 0.00 10.85 0.00 2.39

22 -0.00 19.26 0.00 -2.07 0.00 -2.39
8 50 0.00 -20.57 0.00 12.61 0.00 2.75
22 -0.00 22.25 0.00 -2.39 0.00 -2.75
11 50 0.00 -16.67 0.00 10.30 0.00 0.57
22 -0.00 18.20 0.00 -1.98 0.00 -0.57
12 50 0.00 -19.71 0.00 8.58 0.00 2.40
22 -0.00 21.24 0.00 1.18 0.00 -2.40
13 50 0.00 -16.83 0.00 10.33 -0.00 4.02
22 -0.00 18.36 0.00 -1.94 0.00 -4.02
14 50 -0.00 -13.79 0.00 12.04 0.00 2.18
22 0.00 15.32 0.00 -5.09 0.00 -2.18
15 50 0.00 -11.18 0.00 6.94 0.00 -0.17
22 -0.00 12.28 0.00 -1.34 0.00 0.17
16 50 0.00 -14.22 0.00 5.22 0.00 1.67
22 -0.00 15.32 0.00 1.82 0.00 -1.67
17 50 0.00 -11.34 0.00 6.97 -0.00 3.28
22 -0.00 12.44 0.00 -1.30 0.00 -3.28
18 50 -0.00 -8.30 0.00 8.68 0.00 1.45
22 0.00 9.40 0.00 -4.46 0.00 -1.45

65 7 50 -0.00 5.25 0.00 0.05 -0.00 -0.00

51 0.00 5.25 -0.00 -0.05 -0.00 0.00

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 38 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 39

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

8 50 -0.00 5.64 0.00 0.07 -0.00 -0.00

51 0.00 5.64 -0.00 -0.07 -0.00 0.00
11 50 0.00 4.85 -0.00 0.13 -0.00 -0.00
51 -0.00 4.85 0.00 -0.13 -0.00 0.00
12 50 -0.00 4.85 0.00 -0.94 -0.00 0.00
51 0.00 4.85 -0.00 0.94 -0.00 -0.00
13 50 0.00 4.85 -0.00 0.08 -0.00 -0.00
51 -0.00 4.85 0.00 -0.08 -0.00 0.00
14 50 -0.00 4.85 0.00 1.15 0.00 -0.00
51 0.00 4.85 -0.00 -1.15 0.00 0.00
15 50 0.00 3.37 -0.00 0.11 -0.00 -0.00
51 -0.00 3.37 0.00 -0.11 -0.00 0.00
16 50 -0.00 3.37 0.00 -0.96 -0.00 0.00
51 0.00 3.37 -0.00 0.96 -0.00 -0.00
17 50 0.00 3.37 -0.00 0.06 -0.00 -0.00
51 -0.00 3.37 0.00 -0.06 -0.00 0.00
18 50 -0.00 3.37 0.00 1.13 0.00 -0.00
51 0.00 3.37 -0.00 -1.13 0.00 0.00

67 7 53 0.00 -9.17 0.00 -4.22 -0.00 -31.19

29 -0.00 35.77 -0.00 4.03 -0.00 -36.79
8 53 0.00 -11.48 0.00 -4.86 -0.00 -37.87
29 -0.00 42.90 -0.00 4.63 -0.00 -44.40
11 53 -0.00 -13.83 0.00 -3.54 0.00 -32.66
29 0.00 39.32 -0.00 3.31 0.00 -47.74
12 53 0.00 -7.72 0.00 -6.85 -0.00 -27.91
29 -0.00 33.22 -0.00 6.68 0.00 -34.02
13 53 -0.00 -4.48 0.00 -4.12 -0.00 -27.97
29 0.00 29.97 -0.00 3.98 -0.00 -24.16
14 53 -0.00 -10.58 -0.00 -0.81 0.00 -32.71
29 0.00 36.08 0.00 0.62 0.00 -37.87
15 53 -0.00 -10.73 0.00 -2.25 0.00 -22.50
29 0.00 27.83 -0.00 2.08 0.00 -35.84
16 53 0.00 -4.63 0.00 -5.56 -0.00 -17.75
29 -0.00 21.73 -0.00 5.45 0.00 -22.12
17 53 -0.00 -1.38 0.00 -2.83 -0.00 -17.80
29 0.00 18.48 -0.00 2.75 -0.00 -12.25
18 53 -0.00 -7.49 -0.00 0.48 0.00 -22.55
29 0.00 24.59 0.00 -0.61 0.00 -25.97

68 7 53 0.00 -0.22 0.00 9.93 0.00 0.33

24 -0.00 33.93 0.00 37.74 0.00 -0.33
8 53 0.00 0.89 0.00 11.34 0.00 0.41
24 -0.00 40.53 0.00 43.99 0.00 -0.41
11 53 0.00 0.86 0.00 8.81 0.00 3.06
24 -0.00 31.95 0.00 34.59 0.00 -3.06

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 39 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 40

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

12 53 0.00 -5.38 0.00 12.85 0.00 0.50

24 -0.00 38.19 0.00 47.96 0.00 -0.50
13 53 0.00 -0.44 0.00 9.88 0.00 -2.10
24 -0.00 33.25 0.00 37.15 0.00 2.10
14 53 0.00 5.79 0.00 5.84 0.00 0.46
24 -0.00 27.02 0.00 23.79 0.00 -0.46
15 53 0.00 0.57 0.00 5.80 0.00 2.95
24 -0.00 21.10 0.00 22.87 0.00 -2.95
16 53 0.00 -5.67 0.00 9.84 0.00 0.39
24 -0.00 27.34 0.00 36.24 0.00 -0.39
17 53 0.00 -0.73 0.00 6.87 0.00 -2.21
24 -0.00 22.41 0.00 25.43 0.00 2.21
18 53 0.00 5.50 0.00 2.83 0.00 0.35
24 -0.00 16.17 0.00 12.06 0.00 -0.35

69 7 54 -0.00 -4.84 0.00 20.78 -0.00 2.39

50 0.00 12.30 0.00 -10.90 -0.00 -2.39
8 54 -0.00 -6.37 0.00 24.99 -0.00 2.75
50 0.00 14.93 0.00 -12.68 -0.00 -2.75
11 54 -0.00 -4.74 0.00 19.98 -0.00 0.56
50 0.00 11.81 0.00 -10.42 -0.00 -0.56
12 54 -0.00 -7.78 0.00 20.54 0.00 2.40
50 0.00 14.85 0.00 -7.64 0.00 -2.40
13 54 0.00 -4.90 0.00 20.14 -0.00 4.01
50 -0.00 11.97 0.00 -10.41 0.00 -4.01
14 54 -0.00 -1.86 0.00 19.58 -0.00 2.18
50 0.00 8.93 0.00 -13.19 -0.00 -2.18
15 54 -0.00 -3.01 0.00 13.28 -0.00 -0.17
50 0.00 7.81 0.00 -7.04 -0.00 0.17
16 54 -0.00 -6.05 0.00 13.85 0.00 1.67
50 0.00 10.85 0.00 -4.26 0.00 -1.67
17 54 0.00 -3.17 0.00 13.45 -0.00 3.28
50 -0.00 7.97 0.00 -7.03 0.00 -3.28
18 54 -0.00 -0.13 0.00 12.88 -0.00 1.45
50 0.00 4.93 0.00 -9.81 -0.00 -1.45

70 7 54 -0.00 10.11 -0.00 3.02 -0.00 -0.01

43 0.00 10.12 0.00 -3.02 -0.00 0.01
8 54 0.00 11.99 -0.00 3.57 -0.00 -0.01
43 -0.00 12.01 0.00 -3.57 -0.00 0.01
11 54 0.00 9.71 -0.00 2.79 -0.00 -0.01
43 -0.00 9.72 0.00 -2.79 -0.00 0.01
12 54 0.00 9.71 0.00 2.58 0.00 -0.01
43 -0.00 9.72 -0.00 -2.58 0.00 0.01
13 54 0.00 9.71 -0.00 2.99 -0.00 -0.01
43 -0.00 9.72 0.00 -2.99 -0.00 0.01

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 40 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 41

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

14 54 -0.00 9.71 0.00 3.19 0.00 -0.01

43 0.00 9.72 -0.00 -3.19 0.00 0.01
15 54 0.00 6.50 -0.00 1.83 -0.00 -0.01
43 -0.00 6.51 0.00 -1.83 -0.00 0.01
16 54 0.00 6.50 0.00 1.63 0.00 -0.00
43 -0.00 6.51 -0.00 -1.63 0.00 0.00
17 54 0.00 6.50 -0.00 2.04 -0.00 -0.01
43 -0.00 6.51 0.00 -2.04 -0.00 0.01
18 54 -0.00 6.50 0.00 2.24 0.00 -0.01
43 0.00 6.51 -0.00 -2.24 0.00 0.01

71 7 29 -0.00 27.01 0.00 -14.81 -0.00 2.68

30 0.00 25.48 0.00 12.66 0.00 -2.68
8 29 0.00 27.25 0.00 -15.97 -0.00 3.25
30 -0.00 24.17 0.00 11.64 0.00 -3.25
11 29 0.00 26.71 0.00 -16.74 0.00 2.95
30 -0.00 20.29 0.00 7.74 -0.00 -2.95
12 29 -0.00 12.19 0.00 2.84 0.00 2.60
30 0.00 34.81 0.00 28.82 0.00 -2.60
13 29 0.00 23.87 0.00 -13.05 0.00 2.43
30 -0.00 23.13 0.00 12.00 0.00 -2.43
14 29 0.00 38.39 0.00 -32.62 0.00 2.77
30 -0.00 8.62 0.00 -9.07 0.00 -2.77
15 29 0.00 19.64 0.00 -12.54 0.00 2.08
30 -0.00 14.10 0.00 4.78 -0.00 -2.08
16 29 -0.00 5.12 0.00 7.04 0.00 1.73
30 0.00 28.62 0.00 25.86 0.00 -1.73
17 29 0.00 16.80 0.00 -8.85 0.00 1.56
30 -0.00 16.94 0.00 9.04 0.00 -1.56
18 29 0.00 31.32 0.00 -28.42 0.00 1.90
30 -0.00 2.43 0.00 -12.03 0.00 -1.90

72 7 51 0.00 -29.57 0.00 -12.09 0.00 -0.86

29 -0.00 30.83 0.00 26.44 -0.00 0.86
8 51 0.00 -33.82 0.00 -13.99 0.00 -0.99
29 -0.00 34.90 0.00 30.31 -0.00 0.99
11 51 0.00 -26.60 0.00 -9.70 -0.00 0.39
29 -0.00 27.67 0.00 22.59 -0.00 -0.39
12 51 0.00 -31.24 0.00 -19.05 0.00 -0.73
29 -0.00 32.31 0.00 34.14 -0.00 0.73
13 51 0.00 -28.95 0.00 -12.30 0.00 -1.92
29 -0.00 30.02 0.00 26.31 -0.00 1.92
14 51 0.00 -24.31 0.00 -2.96 -0.00 -0.80
29 -0.00 25.38 0.00 14.76 0.00 0.80
15 51 0.00 -17.61 0.00 -5.98 -0.00 0.65
29 -0.00 18.42 0.00 14.53 -0.00 -0.65

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 41 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 42

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

16 51 0.00 -22.25 0.00 -15.32 0.00 -0.47

29 -0.00 23.06 0.00 26.08 0.00 0.47
17 51 0.00 -19.96 0.00 -8.58 0.00 -1.65
29 -0.00 20.77 0.00 18.25 -0.00 1.65
18 51 0.00 -15.32 0.00 0.76 -0.00 -0.53
29 -0.00 16.13 0.00 6.71 0.00 0.53

73 7 29 -0.00 7.69 0.00 0.11 -0.00 8.76

34 0.00 -3.67 -0.00 -0.08 -0.00 2.79
8 29 -0.00 8.41 0.00 -0.03 -0.00 10.25
34 0.00 -4.96 -0.00 0.07 -0.00 3.35
11 29 0.00 -5.05 -0.00 0.31 -0.00 -3.08
34 -0.00 8.50 0.00 -0.35 -0.00 -10.71
12 29 -0.00 7.26 -0.00 0.14 0.00 8.19
34 0.00 -3.81 0.00 -0.11 0.00 3.08
13 29 -0.00 18.52 0.00 -0.03 -0.00 19.04
34 0.00 -15.07 -0.00 0.12 -0.00 15.12
14 29 0.00 6.21 -0.00 0.14 0.00 7.77
34 -0.00 -2.76 0.00 -0.11 0.00 1.34
15 29 0.00 -7.27 -0.00 0.32 -0.00 -5.82
34 -0.00 9.86 0.00 -0.37 -0.00 -11.60
16 29 -0.00 5.05 -0.00 0.15 0.00 5.46
34 0.00 -2.46 0.00 -0.13 0.00 2.18
17 29 -0.00 16.30 0.00 -0.01 -0.00 16.31
34 0.00 -13.72 -0.00 0.10 -0.00 14.22
18 29 0.00 3.99 -0.00 0.15 0.00 5.04
34 -0.00 -1.40 0.00 -0.14 0.00 0.45

74 7 5 2.29 28.34 5.54 9.04 -0.01 -4.32

55 -2.29 -18.44 -5.54 7.58 0.01 -2.55
8 5 2.77 27.03 5.62 9.21 0.00 -5.19
55 -2.77 -18.55 -5.62 7.65 -0.00 -3.11
11 5 -0.53 21.57 4.76 7.90 -0.36 -1.14
55 0.53 -13.09 -4.76 6.39 0.36 2.73
12 5 2.86 22.49 2.73 7.30 -0.39 -5.02
55 -2.86 -14.01 -2.73 0.89 0.39 -3.57
13 5 5.49 28.79 5.01 8.68 -0.11 -7.86
55 -5.49 -20.30 -5.01 6.34 0.11 -8.61
14 5 2.12 27.86 7.00 9.18 -0.08 -4.02
55 -2.12 -19.38 -7.00 11.82 0.08 -2.33
15 5 -1.27 14.64 3.30 5.50 -0.36 0.25
55 1.27 -8.28 -3.30 4.41 0.36 3.56
16 5 2.12 15.56 1.27 4.91 -0.40 -3.63
55 -2.12 -9.20 -1.27 -1.10 0.40 -2.73
17 5 4.75 21.86 3.55 6.28 -0.11 -6.47
55 -4.75 -15.49 -3.55 4.35 0.11 -7.77

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 42 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 43

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

18 5 1.37 20.93 5.54 6.79 -0.08 -2.63

55 -1.37 -14.57 -5.54 9.84 0.08 -1.49

75 7 6 15.03 61.01 3.10 5.12 -0.01 -27.28

56 -15.03 -51.12 -3.10 4.19 0.01 -17.81
8 6 18.30 62.80 3.42 5.75 0.00 -32.64
56 -18.30 -54.32 -3.42 4.50 -0.00 -22.26
11 6 11.44 53.16 2.39 4.13 -0.36 -23.12
56 -11.44 -44.68 -2.39 3.05 0.36 -11.21
12 6 14.68 56.14 -4.48 -4.97 -0.39 -26.73
56 -14.68 -47.66 4.48 -8.48 0.39 -17.32
13 6 17.84 58.19 2.44 4.43 -0.11 -29.58
56 -17.84 -49.71 -2.44 2.89 0.11 -23.93
14 6 14.60 55.21 9.27 13.43 -0.08 -25.98
56 -14.60 -46.73 -9.27 14.37 0.08 -17.82
15 6 6.53 36.80 1.49 2.60 -0.36 -14.38
56 -6.53 -30.44 -1.49 1.87 0.36 -5.21
16 6 9.77 39.79 -5.38 -6.49 -0.40 -17.99
56 -9.77 -33.43 5.38 -9.66 0.40 -11.32
17 6 12.92 41.83 1.54 2.91 -0.11 -20.84
56 -12.92 -35.47 -1.54 1.71 0.11 -17.93
18 6 9.69 38.86 8.37 11.91 -0.08 -17.24
56 -9.69 -32.49 -8.37 13.19 0.08 -11.82

76 7 7 2.18 45.82 -5.23 -8.42 -0.01 -3.26

57 -2.18 -35.92 5.23 -7.28 0.01 -3.27
8 7 2.86 44.74 -4.93 -7.96 0.00 -4.18
57 -2.86 -36.26 4.93 -6.82 -0.00 -4.40
11 7 -1.97 36.22 -5.12 -8.17 -0.36 2.43
57 1.97 -27.73 5.12 -7.19 0.36 3.49
12 7 2.17 38.16 -11.69 -16.57 -0.39 -3.30
57 -2.17 -29.68 11.69 -18.49 0.39 -3.20
13 7 6.04 45.03 -5.08 -7.79 -0.11 -8.47
57 -6.04 -36.54 5.08 -7.46 0.11 -9.63
14 7 1.89 43.07 1.44 0.51 -0.08 -2.73
57 -1.89 -34.59 -1.44 3.80 0.08 -2.93
15 7 -2.75 24.69 -3.86 -6.14 -0.36 3.56
57 2.75 -18.33 3.86 -5.45 0.36 4.69
16 7 1.39 26.63 -10.43 -14.53 -0.40 -2.17
57 -1.39 -20.27 10.43 -16.75 0.40 -2.01
17 7 5.26 33.50 -3.82 -5.75 -0.11 -7.34
57 -5.26 -27.14 3.82 -5.72 0.11 -8.43
18 7 1.11 31.54 2.70 2.55 -0.08 -1.60
57 -1.11 -25.18 -2.70 5.54 0.08 -1.73

77 7 8 2.95 24.44 -2.84 -4.55 -0.01 -6.37

58 -2.95 -14.54 2.84 -3.96 0.01 -2.50

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 43 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 44

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

8 8 3.06 22.72 -2.63 -4.25 0.00 -6.31

58 -3.06 -14.24 2.63 -3.63 -0.00 -2.86
11 8 1.04 17.25 -2.84 -4.50 -0.36 -8.15
58 -1.04 -8.76 2.84 -4.01 0.36 5.02
12 8 2.56 26.11 -6.85 -10.25 -0.39 -5.87
58 -2.56 -17.63 6.85 -10.31 0.39 -1.82
13 8 4.01 25.89 -2.81 -4.42 -0.11 -3.33
58 -4.01 -17.40 2.81 -4.01 0.11 -8.70
14 8 2.45 17.02 1.19 1.29 -0.08 -5.52
58 -2.45 -8.54 -1.19 2.28 0.08 -1.83
15 8 0.24 11.45 -2.17 -3.42 -0.36 -6.52
58 -0.24 -5.09 2.17 -3.08 0.36 5.78
16 8 1.77 20.32 -6.19 -9.17 -0.40 -4.24
58 -1.77 -13.96 6.19 -9.39 0.40 -1.06
17 8 3.21 20.09 -2.14 -3.33 -0.11 -1.70
58 -3.21 -13.73 2.14 -3.09 0.11 -7.94
18 8 1.65 11.23 1.86 2.38 -0.08 -3.89
58 -1.65 -4.87 -1.86 3.20 0.08 -1.07

78 7 13 -0.80 20.91 6.94 19.24 -0.01 1.55

59 0.80 -11.01 -6.94 1.56 0.01 0.84
8 13 -1.03 22.32 7.79 21.53 0.00 1.94
59 1.03 -13.83 -7.79 1.85 -0.00 1.15
11 13 -7.61 18.67 6.61 18.31 -0.36 11.88
59 7.61 -10.19 -6.61 1.53 0.36 10.94
12 13 0.58 19.35 7.13 20.54 -0.39 -0.57
59 -0.58 -10.86 -7.13 0.84 0.39 -1.18
13 13 7.12 20.02 6.57 18.28 -0.11 -10.50
59 -7.12 -11.53 -6.57 1.43 0.11 -10.85
14 13 -1.05 19.34 6.04 16.01 -0.08 1.91
59 1.05 -10.86 -6.04 2.12 0.08 1.24
15 13 -7.33 12.82 4.55 12.62 -0.36 11.35
59 7.33 -6.46 -4.55 1.03 0.36 10.63
16 13 0.86 13.49 5.07 14.85 -0.40 -1.09
59 -0.86 -7.13 -5.07 0.35 0.40 -1.49
17 13 7.40 14.16 4.51 12.59 -0.11 -11.02
59 -7.40 -7.80 -4.51 0.94 0.11 -11.17
18 13 -0.77 13.49 3.98 10.32 -0.08 1.38
59 0.77 -7.13 -3.98 1.62 0.08 0.92

80 7 15 2.39 50.75 -11.21 -16.72 -0.01 -7.36

61 -2.39 -40.86 11.21 -16.90 0.01 0.20
8 15 2.80 60.28 -13.77 -20.65 0.00 -8.91
61 -2.80 -51.80 13.77 -20.65 -0.00 0.51
11 15 -4.44 53.82 -10.91 -16.46 -0.36 3.70
61 4.44 -45.34 10.91 -16.28 0.36 9.62

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 44 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 45

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

12 15 2.15 41.93 -20.19 -27.23 -0.39 -6.73

61 -2.15 -33.45 20.19 -33.33 0.39 0.27
13 15 8.60 43.57 -11.40 -16.59 -0.11 -17.28
61 -8.60 -35.08 11.40 -17.61 0.11 -8.53
14 15 2.00 55.45 -2.15 -5.86 -0.08 -6.83
61 -2.00 -46.97 2.15 -0.58 0.08 0.83
15 15 -5.19 37.70 -7.21 -10.90 -0.36 6.09
61 5.19 -31.34 7.21 -10.73 0.36 9.47
16 15 1.41 25.81 -16.48 -21.67 -0.40 -4.34
61 -1.41 -19.45 16.48 -27.78 0.40 0.12
17 15 7.86 27.45 -7.70 -11.03 -0.11 -14.89
61 -7.86 -21.08 7.70 -12.06 0.11 -8.67
18 15 1.25 39.33 1.56 -0.30 -0.08 -4.44
61 -1.25 -32.97 -1.56 4.97 0.08 0.68

81 7 16 -1.27 25.61 -0.32 -0.73 -0.01 2.39

62 1.27 -15.71 0.32 -0.22 0.01 1.42
8 16 -1.32 25.75 -0.75 -1.75 0.00 2.22
62 1.32 -17.27 0.75 -0.50 -0.00 1.73
11 16 -9.38 21.66 -1.31 -1.80 -0.36 14.28
62 9.38 -13.18 1.31 -2.14 0.36 13.86
12 16 -1.56 32.39 -6.10 -5.95 -0.39 2.79
62 1.56 -23.91 6.10 -12.36 0.39 1.89
13 16 5.91 24.94 -0.05 -0.53 -0.11 -8.38
62 -5.91 -16.46 0.05 0.40 0.11 -9.34
14 16 -1.94 14.23 4.72 3.57 -0.08 3.15
62 1.94 -5.74 -4.72 10.59 0.08 2.67
15 16 -9.03 14.99 -1.10 -1.29 -0.36 13.71
62 9.03 -8.62 1.10 -2.00 0.36 13.40
16 16 -1.22 25.72 -5.88 -5.44 -0.40 2.23
62 1.22 -19.36 5.88 -12.21 0.40 1.42
17 16 6.25 18.27 0.17 -0.02 -0.11 -8.94
62 -6.25 -11.91 -0.17 0.54 0.11 -9.80
18 16 -1.59 7.55 4.94 4.08 -0.08 2.58
62 1.59 -1.19 -4.94 10.73 0.08 2.20

82 7 20 0.57 25.39 3.90 7.37 -0.01 -1.99

63 -0.57 -15.49 -3.90 4.33 0.01 0.30
8 20 0.12 27.23 4.63 8.31 0.00 -1.06
63 -0.12 -18.75 -4.63 5.59 -0.00 0.69
11 20 -5.71 23.79 3.97 7.27 -0.36 4.84
63 5.71 -15.31 -3.97 4.66 0.36 12.30
12 20 1.75 20.61 1.04 3.28 -0.39 -3.13
63 -1.75 -12.13 -1.04 -0.17 0.39 -2.12
13 20 7.52 23.16 3.57 6.70 -0.11 -9.06
63 -7.52 -14.68 -3.57 4.01 0.11 -13.51

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 45 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 46

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

14 20 0.10 26.34 6.51 10.69 -0.08 -1.19

63 -0.10 -17.86 -6.51 8.83 0.08 0.88
15 20 -5.72 16.64 2.74 5.07 -0.36 5.06
63 5.72 -10.28 -2.74 3.14 0.36 12.10
16 20 1.74 13.46 -0.20 1.08 -0.40 -2.91
63 -1.74 -7.10 0.20 -1.68 0.40 -2.33
17 20 7.52 16.01 2.33 4.50 -0.11 -8.84
63 -7.52 -9.65 -2.33 2.50 0.11 -13.71
18 20 0.09 19.19 5.27 8.49 -0.08 -0.96
63 -0.09 -12.83 -5.27 7.32 0.08 0.68

83 7 21 -8.50 49.39 1.87 6.37 -0.01 15.30

64 8.50 -39.49 -1.87 -0.76 0.01 10.20
8 21 -10.27 58.47 2.81 9.43 0.00 18.10
64 10.27 -49.99 -2.81 -1.01 -0.00 12.70
11 21 -15.99 45.26 2.32 7.10 -0.36 25.53
64 15.99 -36.78 -2.32 -0.15 0.36 22.45
12 21 -7.43 48.81 -3.23 -0.60 -0.39 13.86
64 7.43 -40.33 3.23 -9.11 0.39 8.43
13 21 -0.12 49.48 1.65 6.27 -0.11 3.39
64 0.12 -41.00 -1.65 -1.33 0.11 -3.03
14 21 -8.67 45.93 7.20 13.98 -0.08 15.05
64 8.67 -37.44 -7.20 7.63 0.08 10.97
15 21 -13.24 29.63 1.54 4.50 -0.36 20.70
64 13.24 -23.27 -1.54 0.13 0.36 19.03
16 21 -4.68 33.19 -4.01 -3.20 -0.40 9.02
64 4.68 -26.83 4.01 -8.83 0.40 5.01
17 21 2.63 33.85 0.87 3.67 -0.11 -1.45
64 -2.63 -27.49 -0.87 -1.05 0.11 -6.46
18 21 -5.92 30.30 6.42 11.37 -0.08 10.21
64 5.92 -23.94 -6.42 7.90 0.08 7.55

84 7 26 -1.36 29.63 6.97 12.19 -0.01 3.24

65 1.36 -19.74 -6.97 8.72 0.01 0.83
8 26 -1.67 28.59 7.15 12.57 0.00 3.64
65 1.67 -20.10 -7.15 8.89 -0.00 1.36
11 26 -4.69 29.99 6.21 11.14 -0.36 7.25
65 4.69 -21.50 -6.21 7.48 0.36 6.83
12 26 -1.11 23.37 4.62 10.11 -0.39 2.66
65 1.11 -14.88 -4.62 3.76 0.39 0.68
13 26 2.74 22.55 6.70 10.99 -0.11 -2.03
65 -2.74 -14.07 -6.70 9.12 0.11 -6.19
14 26 -0.81 29.16 8.31 12.09 -0.08 2.51
65 0.81 -20.68 -8.31 12.86 0.08 -0.07
15 26 -4.24 22.64 4.35 7.87 -0.36 6.29
65 4.24 -16.28 -4.35 5.17 0.36 6.45

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 46 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 47

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

16 26 -0.67 16.02 2.76 6.84 -0.40 1.70

65 0.67 -9.66 -2.76 1.45 0.40 0.30
17 26 3.19 15.20 4.84 7.71 -0.11 -3.00
65 -3.19 -8.84 -4.84 6.81 0.11 -6.58
18 26 -0.36 21.82 6.45 8.81 -0.08 1.54
65 0.36 -15.46 -6.45 10.54 0.08 -0.46

85 7 29 -4.86 38.84 -7.03 -9.87 -0.01 12.04

66 4.86 -28.95 7.03 -11.22 0.01 2.55
8 29 -5.92 43.43 -8.26 -11.77 0.00 14.71
66 5.92 -34.95 8.26 -13.00 -0.00 3.05
11 29 -7.61 36.67 -5.07 -7.41 -0.36 17.41
66 7.61 -28.19 5.07 -7.81 0.36 5.41
12 29 -4.45 31.42 -15.54 -20.35 -0.39 11.02
66 4.45 -22.94 15.54 -26.27 0.39 2.34
13 29 -1.99 36.78 -7.49 -10.69 -0.11 6.35
66 1.99 -28.30 7.49 -11.78 0.11 -0.38
14 29 -5.15 42.04 3.01 2.32 -0.08 12.75
66 5.15 -33.56 -3.01 6.71 0.08 2.70
15 29 -6.02 25.18 -2.87 -4.26 -0.36 13.46
66 6.02 -18.82 2.87 -4.35 0.36 4.60
16 29 -2.86 19.93 -13.34 -17.20 -0.40 7.06
66 2.86 -13.57 13.34 -22.81 0.40 1.52
17 29 -0.40 25.29 -5.29 -7.54 -0.11 2.39
66 0.40 -18.93 5.29 -8.32 0.11 -1.20
18 29 -3.56 30.55 5.21 5.47 -0.08 8.80
66 3.56 -24.19 -5.21 10.17 0.08 1.88

86 7 30 -1.51 21.68 0.53 0.78 -0.01 2.90

67 1.51 -11.79 -0.53 0.79 0.01 1.64
8 30 -1.70 21.07 0.31 0.12 0.00 3.46
67 1.70 -12.58 -0.31 0.80 -0.00 1.66
11 30 -6.40 24.49 2.14 1.87 -0.36 10.25
67 6.40 -16.01 -2.14 4.56 0.36 8.95
12 30 -1.95 27.61 -4.20 -3.52 -0.39 3.36
67 1.95 -19.13 4.20 -9.09 0.39 2.49
13 30 2.78 14.26 -0.65 -0.44 -0.11 -3.54
67 -2.78 -5.78 0.65 -1.52 0.11 -4.81
14 30 -1.69 11.14 5.73 5.01 -0.08 3.39
67 1.69 -2.66 -5.73 12.17 0.08 1.68
15 30 -5.95 19.07 2.07 1.87 -0.36 9.33
67 5.95 -12.71 -2.07 4.35 0.36 8.52
16 30 -1.50 22.19 -4.27 -3.52 -0.40 2.44
67 1.50 -15.83 4.27 -9.29 0.40 2.06
17 30 3.24 8.84 -0.72 -0.44 -0.11 -4.47
67 -3.24 -2.48 0.72 -1.72 0.11 -5.24

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 47 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 48

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

18 30 -1.24 5.72 5.66 5.02 -0.08 2.46

67 1.24 0.64 -5.66 11.96 0.08 1.25

87 7 32 -4.68 57.26 4.23 6.89 -0.01 7.78

68 4.68 -47.37 -4.23 5.80 0.01 6.27
8 32 -5.94 55.07 4.27 7.10 0.00 9.91
68 5.94 -46.58 -4.27 5.71 -0.00 7.92
11 32 -8.73 55.94 3.73 6.21 -0.36 12.53
68 8.73 -47.45 -3.73 4.98 0.36 13.65
12 32 -5.07 49.49 -2.31 -1.95 -0.39 8.40
68 5.07 -41.01 2.31 -4.99 0.39 6.81
13 32 -0.12 45.93 4.85 7.42 -0.11 2.35
68 0.12 -37.45 -4.85 7.14 0.11 -2.00
14 32 -3.76 52.38 10.93 15.65 -0.08 6.45
68 3.76 -43.90 -10.93 17.16 0.08 4.83
15 32 -7.12 41.80 2.62 4.36 -0.36 9.85
68 7.12 -35.43 -2.62 3.51 0.36 11.52
16 32 -3.46 35.35 -3.42 -3.80 -0.40 5.72
68 3.46 -28.99 3.42 -6.47 0.40 4.67
17 32 1.49 31.79 3.75 5.57 -0.11 -0.33
68 -1.49 -25.43 -3.75 5.67 0.11 -4.14
18 32 -2.16 38.24 9.83 13.80 -0.08 3.77
68 2.16 -31.88 -9.83 15.68 0.08 2.69

88 7 34 -1.26 37.05 -4.79 -8.06 -0.01 1.77

69 1.26 -27.16 4.79 -6.32 0.01 2.02
8 34 -1.05 31.82 -4.17 -7.24 0.00 1.38
69 1.05 -23.34 4.17 -5.28 -0.00 1.76
11 34 -1.47 31.37 -4.98 -8.26 -0.36 1.72
69 1.47 -22.89 4.98 -6.69 0.36 2.68
12 34 -2.57 29.64 -9.11 -13.84 -0.39 3.77
69 2.57 -21.16 9.11 -13.51 0.39 3.94
13 34 -0.44 32.54 -2.57 -5.02 -0.11 0.90
69 0.44 -24.06 2.57 -2.69 0.11 0.41
14 34 0.67 34.29 1.60 0.64 -0.08 -1.15
69 -0.67 -25.80 -1.60 4.16 0.08 -0.85
15 34 -1.21 23.41 -3.93 -6.43 -0.36 1.38
69 1.21 -17.05 3.93 -5.37 0.36 2.24
16 34 -2.31 21.68 -8.07 -12.01 -0.40 3.43
69 2.31 -15.32 8.07 -12.20 0.40 3.50
17 34 -0.18 24.58 -1.52 -3.19 -0.11 0.56
69 0.18 -18.22 1.52 -1.38 0.11 -0.03
18 34 0.93 26.33 2.65 2.47 -0.08 -1.48
69 -0.93 -19.97 -2.65 5.47 0.08 -1.29

89 7 36 -1.02 20.09 -2.98 -4.49 -0.01 1.67

70 1.02 -10.19 2.98 -4.46 0.01 1.38

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 48 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 49

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

8 36 -0.83 17.14 -2.44 -3.62 0.00 1.33

70 0.83 -8.66 2.44 -3.69 -0.00 1.17
11 36 -0.57 17.84 -3.00 -4.33 -0.36 0.17
70 0.57 -9.36 3.00 -4.67 0.36 1.54
12 36 -1.79 20.77 -5.01 -6.21 -0.39 2.65
70 1.79 -12.28 5.01 -8.81 0.39 2.74
13 36 -1.08 15.95 -1.81 -3.41 -0.11 2.52
70 1.08 -7.46 1.81 -2.01 0.11 0.72
14 36 0.14 13.01 0.24 -1.45 -0.08 0.06
70 -0.14 -4.53 -0.24 2.16 0.08 -0.49
15 36 -0.36 13.56 -2.40 -3.44 -0.36 -0.16
70 0.36 -7.20 2.40 -3.75 0.36 1.25
16 36 -1.59 16.48 -4.40 -5.32 -0.40 2.32
70 1.59 -10.12 4.40 -7.90 0.40 2.44
17 36 -0.87 11.67 -1.21 -2.52 -0.11 2.19
70 0.87 -5.30 1.21 -1.10 0.11 0.42
18 36 0.35 8.73 0.84 -0.56 -0.08 -0.27
70 -0.35 -2.37 -0.84 3.07 0.08 -0.78

90 7 39 -0.14 22.33 1.33 3.01 -0.01 -0.04

71 0.14 -14.42 -1.33 0.97 0.01 0.46
8 39 -0.17 25.17 0.95 2.08 0.00 0.00
71 0.17 -18.38 -0.95 0.77 -0.00 0.52
11 39 -9.80 20.71 1.10 2.40 -0.21 9.82
71 9.80 -13.92 -1.10 0.89 0.21 19.59
12 39 -0.83 20.11 0.78 2.41 -0.23 0.71
71 0.83 -13.32 -0.78 -0.06 0.23 1.78
13 39 8.11 21.33 1.07 2.44 -0.06 -8.40
71 -8.11 -14.55 -1.07 0.75 0.06 -15.93
14 39 -0.89 21.93 1.38 2.44 -0.05 0.76
71 0.89 -15.14 -1.38 1.70 0.05 1.93
15 39 -9.76 14.04 0.87 1.91 -0.21 9.82
71 9.76 -8.95 -0.87 0.70 0.21 19.45
16 39 -0.78 13.44 0.56 1.92 -0.23 0.70
71 0.78 -8.35 -0.56 -0.24 0.23 1.64
17 39 8.16 14.66 0.84 1.95 -0.06 -8.40
71 -8.16 -9.57 -0.84 0.56 0.06 -16.07
18 39 -0.85 15.26 1.15 1.95 -0.05 0.75
71 0.85 -10.17 -1.15 1.51 0.05 1.79

91 7 55 0.00 4.11 0.00 0.81 -0.00 1.94

59 0.00 5.88 -0.00 -0.81 -0.00 -2.97
8 55 0.00 4.63 0.00 0.87 -0.00 2.25
59 0.00 7.45 -0.00 -0.87 -0.00 -3.72
11 55 0.00 0.48 0.00 0.86 -0.00 -3.34
59 0.00 9.18 -0.00 -0.86 -0.00 -7.72

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 49 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 50

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

12 55 0.00 4.59 -0.00 0.62 -0.00 2.96

59 0.00 5.07 0.00 -0.62 -0.00 -1.90
13 55 0.00 7.80 0.00 0.74 -0.00 7.86
59 0.00 1.86 -0.00 -0.74 0.00 2.67
14 55 0.00 3.70 0.00 0.99 0.00 1.58
59 0.00 5.96 -0.00 -0.99 -0.00 -3.14
15 55 0.00 -0.74 0.00 0.64 -0.00 -3.93
59 0.00 7.17 -0.00 -0.64 -0.00 -6.72
16 55 0.00 3.36 -0.00 0.40 -0.00 2.36
59 0.00 3.06 0.00 -0.40 -0.00 -0.89
17 55 0.00 6.57 0.00 0.52 -0.00 7.26
59 0.00 -0.15 -0.00 -0.52 0.00 3.68
18 55 0.00 2.47 0.00 0.76 0.00 0.98
59 0.00 3.95 -0.00 -0.76 -0.00 -2.14

92 7 59 0.00 5.13 -0.00 -0.75 -0.00 2.13

63 0.00 4.06 0.00 0.75 -0.00 -2.06
8 59 0.00 6.39 0.00 -0.98 -0.00 2.57
63 0.00 4.67 -0.00 0.98 -0.00 -2.59
11 59 0.00 1.01 -0.00 -0.66 -0.00 -3.22
63 0.00 7.86 0.00 0.66 -0.00 -7.77
12 59 0.00 5.79 0.00 -0.22 -0.00 3.07
63 0.00 3.08 -0.00 0.22 0.00 -0.90
13 59 0.00 9.67 0.00 -0.69 -0.00 8.18
63 0.00 -0.80 -0.00 0.69 0.00 4.65
14 59 0.00 4.90 -0.00 -1.13 0.00 1.90
63 0.00 3.97 0.00 1.13 0.00 -2.19
15 59 0.00 -0.71 -0.00 -0.40 -0.00 -3.91
63 0.00 6.62 0.00 0.40 -0.00 -7.07
16 59 0.00 4.07 0.00 0.05 -0.00 2.38
63 0.00 1.84 -0.00 -0.05 0.00 -0.21
17 59 0.00 7.95 0.00 -0.42 -0.00 7.49
63 0.00 -2.04 -0.00 0.42 0.00 5.35
18 59 0.00 3.18 -0.00 -0.86 0.00 1.22
63 0.00 2.73 0.00 0.86 0.00 -1.49

93 7 63 0.00 4.09 0.00 -0.07 -0.00 2.09

65 0.00 4.81 -0.00 0.07 -0.00 -2.88
8 63 0.00 4.63 0.00 0.06 -0.00 2.40
65 0.00 5.62 -0.00 -0.06 -0.00 -3.38
11 63 0.00 -0.04 0.00 0.07 -0.00 -3.75
65 0.00 8.49 -0.00 -0.07 -0.00 -8.45
12 63 0.00 4.67 -0.00 -0.07 0.00 3.16
65 0.00 3.78 0.00 0.07 0.00 -1.55
13 63 0.00 8.38 0.00 0.02 -0.00 8.63
65 0.00 0.08 -0.00 -0.02 -0.00 3.85

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 50 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 51

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

14 63 0.00 3.68 -0.00 0.16 -0.00 1.74

65 0.00 4.77 0.00 -0.16 -0.00 -3.03
15 63 0.00 -1.27 0.00 0.05 -0.00 -4.39
65 0.00 6.99 -0.00 -0.05 -0.00 -7.55
16 63 0.00 3.44 -0.00 -0.10 0.00 2.53
65 0.00 2.28 0.00 0.10 0.00 -0.65
17 63 0.00 7.15 0.00 -0.01 -0.00 8.00
65 0.00 -1.42 -0.00 0.01 -0.00 4.75
18 63 0.00 2.45 -0.00 0.14 -0.00 1.10
65 0.00 3.27 0.00 -0.14 -0.00 -2.12

94 7 65 0.00 14.92 -0.00 -8.80 0.00 2.05

68 -0.00 15.16 0.00 9.63 0.00 -2.29
8 65 -0.00 14.48 -0.00 -8.83 0.00 2.02
68 0.00 14.25 0.00 9.15 0.00 -2.11
11 65 -0.00 13.01 -0.00 -7.41 0.00 1.62
68 0.00 13.69 0.00 9.09 0.00 -2.10
12 65 -0.00 11.10 -0.00 -3.84 0.00 0.87
68 0.00 15.60 0.00 12.31 0.00 -3.29
13 65 -0.00 13.99 -0.00 -9.10 0.00 2.34
68 0.00 12.71 0.00 7.32 -0.00 -1.83
14 65 -0.00 15.91 -0.00 -12.69 -0.00 3.10
68 0.00 10.79 0.00 4.09 0.00 -0.65
15 65 -0.00 9.29 -0.00 -5.12 0.00 1.10
68 0.00 10.05 0.00 6.75 0.00 -1.57
16 65 0.00 7.37 -0.00 -1.55 0.00 0.35
68 -0.00 11.96 0.00 9.97 0.00 -2.75
17 65 0.00 10.27 -0.00 -6.82 0.00 1.82
68 -0.00 9.07 0.00 4.97 -0.00 -1.30
18 65 -0.00 12.19 0.00 -10.40 -0.00 2.58
68 0.00 7.15 -0.00 1.74 0.00 -0.11

95 7 68 0.00 16.21 -0.00 -11.41 0.00 3.58

69 -0.00 16.33 0.00 11.67 0.00 -3.65
8 68 0.00 13.91 -0.00 -9.81 -0.00 3.17
69 -0.00 13.98 0.00 9.95 0.00 -3.21
11 68 0.00 13.66 0.00 -9.11 -0.00 3.58
69 -0.00 14.24 -0.00 10.36 -0.00 -3.94
12 68 0.00 12.47 0.00 -6.72 -0.00 2.23
69 -0.00 15.42 -0.00 13.13 -0.00 -4.06
13 68 0.00 14.39 0.00 -10.95 -0.00 2.91
69 -0.00 13.51 -0.00 9.04 0.00 -2.36
14 68 -0.00 15.58 -0.00 -13.34 0.00 4.26
69 0.00 12.32 0.00 6.26 0.00 -2.24
15 68 0.00 10.18 0.00 -6.65 -0.00 2.78
69 -0.00 10.74 -0.00 7.88 -0.00 -3.13

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 51 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 52

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

16 68 0.00 8.99 0.00 -4.27 -0.00 1.43

69 -0.00 11.93 -0.00 10.65 -0.00 -3.25
17 68 0.00 10.91 0.00 -8.49 -0.00 2.11
69 -0.00 10.01 -0.00 6.55 0.00 -1.56
18 68 -0.00 12.10 -0.00 -10.89 0.00 3.47
69 0.00 8.82 0.00 3.77 0.00 -1.44

96 7 69 0.00 10.83 0.00 -5.35 0.00 1.63

70 -0.00 10.19 -0.00 4.46 0.00 -1.38
8 69 0.00 9.36 0.00 -4.67 0.00 1.45
70 -0.00 8.66 -0.00 3.69 0.00 -1.17
11 69 0.00 8.66 0.00 -3.67 0.00 1.25
70 -0.00 9.36 -0.00 4.67 0.00 -1.54
12 69 0.00 5.73 0.00 0.38 0.00 0.12
70 -0.00 12.28 -0.00 8.81 0.00 -2.74
13 69 0.00 10.55 0.00 -6.34 0.00 1.95
70 -0.00 7.46 -0.00 2.01 0.00 -0.72
14 69 0.00 13.49 0.00 -10.41 0.00 3.10
70 -0.00 4.53 -0.00 -2.16 0.00 0.49
15 69 0.00 6.31 0.00 -2.50 0.00 0.89
70 -0.00 7.20 -0.00 3.75 0.00 -1.25
16 69 0.00 3.39 0.00 1.55 0.00 -0.25
70 -0.00 10.12 -0.00 7.90 0.00 -2.44
17 69 0.00 8.21 0.00 -5.17 0.00 1.58
70 -0.00 5.30 -0.00 1.10 0.00 -0.42
18 69 0.00 11.14 0.00 -9.24 0.00 2.73
70 -0.00 2.37 -0.00 -3.07 0.00 0.78

97 7 55 0.00 14.33 0.00 -8.39 0.00 0.61

56 -0.00 14.82 0.00 9.25 -0.00 -0.61
8 55 -0.00 13.92 0.00 -8.52 -0.00 0.86
56 0.00 14.09 0.00 8.82 -0.00 -0.86
11 55 0.00 12.61 0.00 -7.26 0.00 0.61
56 -0.00 13.32 0.00 8.53 -0.00 -0.61
12 55 0.00 9.42 0.00 -1.51 -0.00 0.61
56 -0.00 16.51 0.00 14.10 -0.00 -0.61
13 55 0.00 12.50 0.00 -7.08 0.00 0.75
56 -0.00 13.43 0.00 8.72 -0.00 -0.75
14 55 -0.00 15.68 0.00 -12.81 -0.00 0.75
56 0.00 10.25 0.00 3.17 -0.00 -0.75
15 55 0.00 9.02 0.00 -5.05 0.00 0.37
56 -0.00 9.71 0.00 6.27 -0.00 -0.37
16 55 0.00 5.84 0.00 0.70 -0.00 0.38
56 -0.00 12.90 0.00 11.84 -0.00 -0.38
17 55 0.00 8.92 0.00 -4.87 0.00 0.51
56 -0.00 9.82 0.00 6.46 -0.00 -0.51

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 52 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 53

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

18 55 -0.00 12.10 0.00 -10.60 -0.00 0.51

56 0.00 6.64 0.00 0.91 -0.00 -0.51

98 7 56 -0.00 17.57 0.00 -12.92 -0.00 -0.33

57 0.00 17.61 0.00 13.02 -0.00 0.33
8 56 -0.00 16.67 0.00 -12.62 -0.00 -0.48
57 0.00 16.57 0.00 12.41 -0.00 0.48
11 56 -0.00 15.42 0.00 -11.26 -0.00 -0.13
57 0.00 15.69 0.00 11.85 -0.00 0.13
12 56 -0.00 13.41 0.00 -6.85 -0.00 -0.17
57 0.00 17.71 0.00 16.25 -0.00 0.17
13 56 -0.00 15.39 0.00 -11.17 -0.00 -0.45
57 0.00 15.73 0.00 11.92 -0.00 0.45
14 56 -0.00 17.39 0.00 -15.57 -0.00 -0.40
57 0.00 13.72 0.00 7.54 -0.00 0.40
15 56 -0.00 11.16 0.00 -8.01 -0.00 0.01
57 0.00 11.46 0.00 8.67 -0.00 -0.01
16 56 -0.00 9.14 0.00 -3.60 -0.00 -0.04
57 0.00 13.47 0.00 13.07 -0.00 0.04
17 56 -0.00 11.12 0.00 -7.92 -0.00 -0.31
57 0.00 11.49 0.00 8.74 -0.00 0.31
18 56 -0.00 13.13 0.00 -12.32 -0.00 -0.27
57 0.00 9.49 0.00 4.36 -0.00 0.27

99 7 57 0.00 11.84 0.00 -6.16 0.00 -0.37

58 -0.00 10.48 0.00 4.28 0.00 0.37
8 57 0.00 11.35 0.00 -6.16 0.00 -0.48
58 -0.00 9.75 0.00 3.94 0.00 0.48
11 57 -0.00 10.25 0.00 -5.16 0.00 -0.11
58 0.00 9.49 0.00 4.11 0.00 0.11
12 57 0.00 5.61 0.00 1.37 0.00 -0.25
58 -0.00 14.13 0.00 10.45 0.00 0.25
13 57 0.00 10.09 0.00 -4.96 -0.00 -0.49
58 -0.00 9.65 0.00 4.36 0.00 0.49
14 57 0.00 14.71 0.00 -11.47 0.00 -0.35
58 -0.00 5.03 0.00 -1.96 0.00 0.35
15 57 -0.00 7.34 0.00 -3.56 0.00 0.02
58 0.00 7.01 0.00 3.11 0.00 -0.02
16 57 0.00 2.70 0.00 2.97 0.00 -0.12
58 -0.00 11.65 0.00 9.45 0.00 0.12
17 57 0.00 7.18 0.00 -3.36 -0.00 -0.36
58 -0.00 7.17 0.00 3.35 0.00 0.36
18 57 0.00 11.80 0.00 -9.88 0.00 -0.22
58 -0.00 2.54 0.00 -2.96 0.00 0.22

100 7 58 0.00 4.06 0.00 -0.33 0.00 2.12

62 -0.00 4.10 -0.00 0.33 0.00 -2.18

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 53 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 54

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

8 58 0.00 4.49 0.00 -0.31 0.00 2.38

62 -0.00 4.47 -0.00 0.31 0.00 -2.35
11 58 0.00 -0.73 0.00 -0.11 0.00 -5.14
62 -0.00 8.34 -0.00 0.11 0.00 -8.24
12 58 0.00 3.50 0.00 -0.14 0.00 1.57
62 -0.00 4.11 -0.00 0.14 0.00 -2.47
13 58 0.00 7.75 0.00 -0.35 0.00 8.21
62 -0.00 -0.14 -0.00 0.35 0.00 3.43
14 58 0.00 3.51 0.00 -0.31 0.00 1.48
62 -0.00 4.10 -0.00 0.31 0.00 -2.36
15 58 0.00 -1.92 0.00 -0.03 0.00 -5.77
62 -0.00 7.16 -0.00 0.03 0.00 -7.62
16 58 0.00 2.31 0.00 -0.06 0.00 0.94
62 -0.00 2.93 -0.00 0.06 0.00 -1.85
17 58 0.00 6.56 0.00 -0.27 0.00 7.58
62 -0.00 -1.32 -0.00 0.27 0.00 4.05
18 58 0.00 2.32 0.00 -0.23 0.00 0.85
62 -0.00 2.93 -0.00 0.23 0.00 -1.74

101 7 56 0.00 18.74 -0.00 -0.52 -0.00 18.75

60 0.00 -3.15 0.00 0.52 -0.00 15.10
8 56 0.00 23.56 -0.00 -0.70 -0.00 23.60
60 0.00 -3.59 0.00 0.70 -0.00 19.12
11 56 0.00 15.93 0.00 -0.32 -0.00 11.95
60 0.00 -0.50 -0.00 0.32 -0.00 14.06
12 56 0.00 17.74 0.00 1.23 0.00 18.11
60 0.00 -2.31 -0.00 -1.23 0.00 13.24
13 56 0.00 20.90 -0.00 -0.44 0.00 25.12
60 0.00 -5.47 0.00 0.44 0.00 15.53
14 56 0.00 19.09 0.00 -1.98 -0.00 18.97
60 0.00 -3.66 -0.00 1.98 -0.00 16.35
15 56 0.00 9.57 0.00 -0.13 -0.00 5.58
60 0.00 0.45 -0.00 0.13 -0.00 8.89
16 56 0.00 11.38 0.00 1.42 0.00 11.74
60 0.00 -1.36 -0.00 -1.42 0.00 8.07
17 56 0.00 14.54 -0.00 -0.25 0.00 18.75
60 0.00 -4.51 0.00 0.25 0.00 10.36
18 56 0.00 12.73 0.00 -1.79 -0.00 12.60
60 0.00 -2.70 -0.00 1.79 -0.00 11.18

102 7 60 0.00 -5.86 -0.00 1.26 0.00 -14.81

64 0.00 20.26 0.00 -1.26 0.00 -21.39
8 60 0.00 -7.27 -0.00 1.65 0.00 -18.75
64 0.00 25.66 0.00 -1.65 0.00 -27.02
11 60 0.00 -8.10 -0.00 1.35 0.00 -15.71
64 0.00 22.33 0.00 -1.35 0.00 -26.45

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 54 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 55

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

12 60 0.00 -4.40 -0.00 -0.51 -0.00 -12.91

64 0.00 18.63 0.00 0.51 -0.00 -19.09
13 60 0.00 -3.19 -0.00 1.23 0.00 -13.38
64 0.00 17.42 0.00 -1.23 0.00 -15.30
14 60 0.00 -6.89 -0.00 3.09 0.00 -16.18
64 0.00 21.12 0.00 -3.09 0.00 -22.65
15 60 0.00 -6.14 -0.00 0.90 0.00 -10.65
64 0.00 15.40 0.00 -0.90 0.00 -19.15
16 60 0.00 -2.44 -0.00 -0.95 -0.00 -7.84
64 0.00 11.70 0.00 0.95 -0.00 -11.79
17 60 0.00 -1.24 -0.00 0.78 0.00 -8.31
64 0.00 10.49 0.00 -0.78 0.00 -8.00
18 60 0.00 -4.93 -0.00 2.64 0.00 -11.11
64 0.00 14.18 0.00 -2.64 0.00 -15.36

103 7 64 0.00 12.49 0.00 -1.82 0.00 10.86

74 0.00 3.39 -0.00 1.82 0.00 2.81
8 64 0.00 15.74 0.00 -2.28 0.00 13.82
74 0.00 4.29 -0.00 2.28 0.00 3.08
11 64 0.00 8.00 0.00 -1.94 0.00 3.22
74 0.00 7.62 -0.00 1.94 0.00 -3.37
12 64 0.00 12.14 0.00 -0.44 -0.00 10.52
74 0.00 3.47 -0.00 0.44 -0.00 2.39
13 64 0.00 16.74 0.00 -1.56 -0.00 18.55
74 0.00 -1.12 -0.00 1.56 -0.00 8.83
14 64 0.00 12.60 0.00 -3.06 -0.00 11.26
74 0.00 3.02 -0.00 3.06 -0.00 3.07
15 64 0.00 3.75 0.00 -1.32 0.00 -0.52
74 0.00 6.46 -0.00 1.32 0.00 -4.18
16 64 0.00 7.90 0.00 0.17 -0.00 6.78
74 0.00 2.32 -0.00 -0.17 -0.00 1.58
17 64 0.00 12.49 0.00 -0.95 -0.00 14.81
74 0.00 -2.28 -0.00 0.95 -0.00 8.02
18 64 0.00 8.35 0.00 -2.44 -0.00 7.52
74 0.00 1.86 -0.00 2.44 -0.00 2.26

104 7 57 0.00 6.48 0.00 0.43 -0.00 3.31

61 -0.00 5.34 -0.00 -0.42 -0.00 -1.62
8 57 0.00 8.34 -0.00 0.58 -0.00 4.40
61 -0.00 6.86 0.00 -0.57 -0.00 -2.21
11 57 0.00 1.79 -0.00 0.50 -0.00 -3.50
61 -0.00 9.92 0.00 -0.53 -0.00 -8.48
12 57 0.00 6.36 -0.00 0.87 -0.00 3.28
61 -0.00 5.35 0.00 -0.86 -0.00 -1.79
13 57 0.00 10.73 -0.00 0.50 0.00 9.68
61 -0.00 0.99 0.00 -0.46 -0.00 4.69

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 55 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 56

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

14 57 -0.00 6.15 0.00 0.14 -0.00 2.88

61 0.00 5.56 -0.00 -0.13 -0.00 -2.01
15 57 0.00 -0.47 -0.00 0.34 -0.00 -4.70
61 -0.00 8.06 0.00 -0.38 -0.00 -7.88
16 57 0.00 4.10 -0.00 0.71 -0.00 2.08
61 -0.00 3.50 0.00 -0.71 -0.00 -1.19
17 57 0.00 8.47 -0.00 0.34 0.00 8.48
61 -0.00 -0.87 0.00 -0.30 -0.00 5.30
18 57 -0.00 3.89 0.00 -0.02 -0.00 1.69
61 0.00 3.70 -0.00 0.02 -0.00 -1.40

105 7 60 0.00 9.00 0.00 -1.78 0.00 -0.30

75 0.00 4.33 0.00 -6.30 0.00 0.30
8 60 0.00 10.86 0.00 -2.35 0.00 -0.38
75 -0.00 5.18 0.00 -7.99 0.00 0.38
11 60 0.00 8.60 0.00 -1.67 -0.00 1.65
75 -0.00 4.27 0.00 -6.03 -0.00 -1.65
12 60 0.00 6.71 0.00 1.73 0.00 -0.33
75 -0.00 6.15 0.00 -3.79 0.00 0.33
13 60 -0.00 8.66 0.00 -1.67 -0.00 -2.15
75 0.00 4.21 0.00 -6.21 -0.00 2.15
14 60 0.00 10.54 0.00 -5.06 0.00 -0.17
75 -0.00 2.32 0.00 -8.44 0.00 0.17
15 60 0.00 5.69 0.00 -1.03 -0.00 1.76
75 -0.00 2.88 0.00 -3.87 -0.00 -1.76
16 60 0.00 3.80 0.00 2.37 0.00 -0.23
75 0.00 4.77 0.00 -1.64 0.00 0.23
17 60 -0.00 5.75 0.00 -1.03 -0.00 -2.05
75 0.00 2.82 0.00 -4.05 -0.00 2.05
18 60 0.00 7.63 0.00 -4.42 0.00 -0.07
75 -0.00 0.94 0.00 -6.28 0.00 0.07

106 7 61 0.00 9.49 0.00 -7.49 0.00 1.12

62 -0.00 5.17 0.00 2.38 0.00 -1.12
8 61 -0.00 12.47 0.00 -9.88 0.00 1.32
62 0.00 6.30 0.00 2.83 -0.00 -1.32
11 61 0.00 9.84 0.00 -7.73 0.00 0.52
62 -0.00 4.68 0.00 1.57 0.00 -0.52
12 61 0.00 0.63 0.00 4.56 -0.00 1.19
62 -0.00 13.88 0.00 14.91 -0.00 -1.19
13 61 -0.00 8.58 0.00 -6.44 -0.00 1.68
62 0.00 5.94 0.00 3.79 -0.00 -1.68
14 61 -0.00 17.77 0.00 -18.71 -0.00 1.01
62 0.00 -3.26 0.00 -9.53 -0.00 -1.01
15 61 0.00 6.45 0.00 -5.05 0.00 0.16
62 -0.00 2.98 0.00 0.81 0.00 -0.16

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 56 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 57

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

16 61 0.00 -2.76 0.00 7.25 -0.00 0.83

62 -0.00 12.19 0.00 14.15 0.00 -0.83
17 61 -0.00 5.19 0.00 -3.76 -0.00 1.32
62 0.00 4.24 0.00 3.03 -0.00 -1.32
18 61 -0.00 14.38 0.00 -16.03 -0.00 0.65
62 0.00 -4.95 0.00 -10.29 -0.00 -0.65

107 7 66 -0.00 7.88 0.00 -5.88 -0.00 -1.11

67 0.00 4.53 0.00 2.10 -0.00 1.11
8 66 -0.00 9.79 0.00 -7.32 -0.00 -1.28
67 0.00 5.10 0.00 2.31 -0.00 1.28
11 66 -0.00 8.55 0.00 -7.13 -0.00 -1.97
67 0.00 3.42 0.00 0.97 -0.00 1.97
12 66 -0.00 0.28 0.00 4.29 0.00 -0.98
67 0.00 11.69 0.00 12.71 0.00 0.98
13 66 0.00 7.65 0.00 -5.50 -0.00 -0.08
67 -0.00 4.32 0.00 1.85 -0.00 0.08
14 66 0.00 15.94 0.00 -16.95 -0.00 -1.06
67 -0.00 -3.97 0.00 -9.92 -0.00 1.06
15 66 -0.00 5.91 0.00 -5.16 -0.00 -1.63
67 0.00 2.07 0.00 0.36 -0.00 1.63
16 66 -0.00 -2.36 0.00 6.26 0.00 -0.64
67 0.00 10.34 0.00 12.10 0.00 0.64
17 66 0.00 5.01 0.00 -3.53 -0.00 0.26
67 -0.00 2.97 0.00 1.24 -0.00 -0.26
18 66 0.00 13.30 0.00 -14.97 0.00 -0.72
67 -0.00 -5.32 0.00 -10.53 -0.00 0.72

108 7 62 -0.00 6.44 0.00 -2.49 -0.00 1.88

72 0.00 -4.89 0.00 -0.47 -0.00 -1.88
8 62 -0.00 6.50 0.00 -2.65 -0.00 1.94
72 0.00 -5.04 0.00 -0.36 -0.00 -1.94
11 62 0.00 0.16 0.00 0.47 0.00 -5.10
72 -0.00 1.20 0.00 -0.18 0.00 5.10
12 62 0.00 5.92 0.00 -2.69 -0.00 1.77
72 -0.00 -4.55 0.00 -0.04 -0.00 -1.77
13 62 0.00 10.67 0.00 -4.53 0.00 7.59
72 -0.00 -9.30 0.00 -0.69 0.00 -7.59
14 62 0.00 4.90 0.00 -1.36 0.00 0.70
72 -0.00 -3.54 0.00 -0.84 0.00 -0.70
15 62 0.00 -1.52 0.00 1.16 0.00 -5.61
72 -0.00 2.51 0.00 -0.09 0.00 5.61
16 62 0.00 4.23 0.00 -2.00 -0.00 1.26
72 -0.00 -3.24 0.00 0.05 -0.00 -1.26
17 62 0.00 8.98 0.00 -3.84 0.00 7.08
72 -0.00 -7.99 0.00 -0.61 0.00 -7.08

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 57 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 58

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

18 62 0.00 3.21 0.00 -0.67 0.00 0.19

72 -0.00 -2.22 0.00 -0.75 0.00 -0.19

109 7 67 -0.00 7.25 0.00 -2.89 -0.00 -2.75

73 0.00 -5.71 0.00 -0.50 -0.00 2.75
8 67 -0.00 7.48 0.00 -3.11 -0.00 -2.94
73 0.00 -6.03 0.00 -0.41 -0.00 2.94
11 67 -0.00 12.59 0.00 -5.53 -0.00 -10.92
73 0.00 -11.23 0.00 -0.71 -0.00 10.92
12 67 -0.00 7.44 0.00 -3.62 -0.00 -3.47
73 0.00 -6.07 0.00 0.09 -0.00 3.47
13 67 -0.00 1.46 0.00 -0.34 -0.00 4.73
73 0.00 -0.10 0.00 -0.06 -0.00 -4.73
14 67 -0.00 6.63 0.00 -2.25 -0.00 -2.74
73 0.00 -5.27 0.00 -0.86 -0.00 2.74
15 67 -0.00 10.64 0.00 -4.71 -0.00 -10.15
73 0.00 -9.65 0.00 -0.61 -0.00 10.15
16 67 -0.00 5.49 0.00 -2.81 -0.00 -2.70
73 0.00 -4.50 0.00 0.20 -0.00 2.70
17 67 -0.00 -0.49 0.00 0.48 -0.00 5.50
73 0.00 1.48 0.00 0.04 -0.00 -5.50
18 67 -0.00 4.68 0.00 -1.43 -0.00 -1.97
73 0.00 -3.69 0.00 -0.76 -0.00 1.97

110 7 72 0.00 4.89 0.00 0.47 0.00 1.88

71 -0.00 7.22 -0.00 -0.47 0.00 -3.18
8 72 0.00 5.04 0.00 0.36 0.00 1.94
71 -0.00 9.17 -0.00 -0.36 0.00 -4.39
11 72 0.00 -1.20 0.00 0.18 0.00 -5.10
71 -0.00 12.78 -0.00 -0.18 0.00 -12.70
12 72 0.00 4.55 0.00 0.04 0.00 1.77
71 -0.00 7.03 -0.00 -0.04 0.00 -3.03
13 72 0.00 9.30 0.00 0.69 0.00 7.59
71 -0.00 2.28 -0.00 -0.69 0.00 4.81
14 72 0.00 3.54 0.00 0.84 0.00 0.70
71 -0.00 8.04 -0.00 -0.84 0.00 -4.88
15 72 0.00 -2.51 0.00 0.09 0.00 -5.61
71 -0.00 10.30 -0.00 -0.09 0.00 -11.49
16 72 0.00 3.24 0.00 -0.05 0.00 1.26
71 -0.00 4.55 -0.00 0.05 0.00 -1.83
17 72 0.00 7.99 0.00 0.61 0.00 7.08
71 -0.00 -0.20 -0.00 -0.61 0.00 6.01
18 72 0.00 2.22 0.00 0.75 0.00 0.19
71 -0.00 5.56 -0.00 -0.75 0.00 -3.68

111 7 71 -0.00 7.20 -0.00 -0.50 -0.00 2.72

73 0.00 5.71 0.00 0.50 -0.00 -2.75

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 58 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 59

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

8 71 -0.00 9.21 -0.00 -0.41 -0.00 3.88

73 0.00 6.03 0.00 0.41 -0.00 -2.94
11 71 -0.00 1.14 -0.00 -0.71 -0.00 -6.89
73 0.00 11.23 0.00 0.71 -0.00 -10.92
12 71 -0.00 6.29 -0.00 0.09 -0.00 1.25
73 0.00 6.07 0.00 -0.09 -0.00 -3.47
13 71 -0.00 12.27 -0.00 -0.06 -0.00 11.12
73 0.00 0.10 0.00 0.06 -0.00 4.73
14 71 -0.00 7.10 -0.00 -0.86 -0.00 2.96
73 0.00 5.27 0.00 0.86 -0.00 -2.74
15 71 -0.00 -1.35 -0.00 -0.61 -0.00 -7.95
73 0.00 9.65 0.00 0.61 -0.00 -10.15
16 71 -0.00 3.80 -0.00 0.20 -0.00 0.19
73 0.00 4.50 0.00 -0.20 -0.00 -2.70
17 71 -0.00 9.78 -0.00 0.04 -0.00 10.06
73 0.00 -1.48 0.00 -0.04 -0.00 5.50
18 71 -0.00 4.61 -0.00 -0.76 -0.00 1.89
73 0.00 3.69 0.00 0.76 -0.00 -1.97

112 7 74 0.00 -13.63 0.00 4.02 -0.00 -4.26

68 0.00 16.00 -0.00 -4.02 -0.00 -7.57
8 74 0.00 -16.15 -0.00 5.06 0.00 -4.85
68 0.00 18.42 0.00 -5.06 0.00 -8.97
11 74 0.00 -18.00 0.00 4.97 -0.00 -0.07
68 0.00 20.11 -0.00 -4.97 -0.00 -15.13
12 74 0.00 -10.83 -0.00 0.60 0.00 -3.74
68 0.00 12.93 0.00 -0.60 -0.00 -5.75
13 74 0.00 -8.24 0.00 3.52 0.00 -8.37
68 0.00 10.35 -0.00 -3.52 -0.00 0.93
14 74 0.00 -15.42 0.00 7.90 0.00 -4.70
68 0.00 17.53 -0.00 -7.90 0.00 -8.45
15 74 0.00 -13.68 0.00 3.60 -0.00 1.21
68 0.00 15.21 -0.00 -3.60 -0.00 -12.73
16 74 0.00 -6.51 -0.00 -0.77 0.00 -2.46
68 0.00 8.03 0.00 0.77 -0.00 -3.35
17 74 0.00 -3.93 0.00 2.15 -0.00 -7.08
68 0.00 5.45 -0.00 -2.15 -0.00 3.33
18 74 0.00 -11.10 0.00 6.53 0.00 -3.42
68 0.00 12.63 -0.00 -6.53 0.00 -6.05

113 7 74 0.00 10.24 0.00 -5.84 0.00 1.44

77 -0.00 0.17 0.00 -9.19 0.00 -1.44
8 74 0.00 11.86 0.00 -7.34 0.00 1.77
77 -0.00 -0.80 0.00 -11.57 0.00 -1.77
11 74 -0.00 10.38 0.00 -6.91 -0.00 3.45
77 0.00 -0.79 0.00 -9.76 -0.00 -3.45

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 59 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 60

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

12 74 0.00 7.35 0.00 -1.04 0.00 1.35

77 -0.00 2.24 0.00 -6.60 0.00 -1.35
13 74 -0.00 9.37 0.00 -5.08 -0.00 -0.46
77 0.00 0.23 0.00 -8.57 0.00 0.46
14 74 0.00 12.40 0.00 -10.96 0.00 1.63
77 -0.00 -2.81 0.00 -11.74 0.00 -1.63
15 74 -0.00 7.22 0.00 -4.92 -0.00 2.97
77 0.00 -0.53 0.00 -6.64 -0.00 -2.97
16 74 0.00 4.19 0.00 0.94 0.00 0.88
77 -0.00 2.50 0.00 -3.47 0.00 -0.88
17 74 -0.00 6.21 0.00 -3.10 -0.00 -0.94
77 0.00 0.49 0.00 -5.44 0.00 0.94
18 74 0.00 9.24 0.00 -8.98 0.00 1.16
77 -0.00 -2.55 0.00 -8.62 0.00 -1.16

114 7 75 0.00 -20.57 0.00 7.27 -0.00 -0.30

61 -0.00 26.02 0.00 24.81 0.00 0.30
8 75 0.00 -26.27 0.00 9.31 0.00 -0.38
61 -0.00 32.47 0.00 31.10 0.00 0.38
11 75 -0.00 -20.43 0.00 7.13 -0.00 1.65
61 0.00 25.58 0.00 24.54 -0.00 -1.65
12 75 0.00 -22.31 0.00 4.64 0.00 -0.33
61 -0.00 27.47 0.00 29.63 0.00 0.33
13 75 -0.00 -20.37 0.00 7.08 0.00 -2.15
61 0.00 25.52 0.00 24.51 0.00 2.15
14 75 0.00 -18.48 0.00 9.56 -0.00 -0.17
61 -0.00 23.64 0.00 19.42 -0.00 0.17
15 75 -0.00 -13.32 0.00 4.61 -0.00 1.76
61 0.00 16.83 0.00 16.15 -0.00 -1.76
16 75 0.00 -15.21 0.00 2.12 0.00 -0.23
61 -0.00 18.71 0.00 21.24 0.00 0.23
17 75 -0.00 -13.26 0.00 4.56 0.00 -2.05
61 0.00 16.77 0.00 16.12 0.00 2.05
18 75 0.00 -11.38 0.00 7.04 -0.00 -0.07
61 -0.00 14.88 0.00 11.03 -0.00 0.07

115 7 75 -0.00 16.24 -0.00 -0.97 0.00 -0.00

77 0.00 16.24 0.00 0.97 0.00 0.00
8 75 -0.00 21.08 -0.00 -1.32 0.00 -0.00
77 0.00 21.08 0.00 1.32 0.00 0.00
11 75 -0.00 16.16 -0.00 -1.10 0.00 -0.00
77 0.00 16.16 0.00 1.10 0.00 0.00
12 75 -0.00 16.16 -0.00 -0.84 0.00 -0.00
77 0.00 16.16 0.00 0.84 0.00 0.00
13 75 -0.00 16.16 -0.00 -0.87 0.00 -0.00
77 0.00 16.16 0.00 0.87 0.00 0.00

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 60 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 61

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

14 75 -0.00 16.16 -0.00 -1.12 0.00 -0.00

77 0.00 16.16 0.00 1.12 0.00 0.00
15 75 -0.00 10.44 -0.00 -0.74 0.00 -0.00
77 0.00 10.44 0.00 0.74 0.00 0.00
16 75 -0.00 10.44 -0.00 -0.48 0.00 -0.00
77 0.00 10.44 0.00 0.48 0.00 0.00
17 75 -0.00 10.44 -0.00 -0.50 0.00 -0.00
77 0.00 10.44 0.00 0.50 0.00 0.00
18 75 -0.00 10.44 -0.00 -0.76 0.00 -0.00
77 0.00 10.44 0.00 0.76 0.00 0.00

116 7 77 -0.00 -16.42 0.00 8.22 -0.00 1.44

66 0.00 21.07 0.00 17.10 -0.00 -1.44
8 77 -0.00 -20.28 0.00 10.25 -0.00 1.77
66 0.00 25.16 0.00 20.32 -0.00 -1.77
11 77 0.00 -15.37 0.00 8.66 -0.00 3.45
66 -0.00 19.64 0.00 14.94 -0.00 -3.45
12 77 -0.00 -18.40 0.00 5.75 -0.00 1.35
66 0.00 22.67 0.00 21.98 -0.00 -1.35
13 77 -0.00 -16.39 0.00 7.70 -0.00 -0.46
66 0.00 20.65 0.00 17.28 -0.00 0.46
14 77 -0.00 -13.35 0.00 10.62 0.00 1.63
66 0.00 17.62 0.00 10.23 -0.00 -1.63
15 77 0.00 -9.92 0.00 5.90 -0.00 2.97
66 -0.00 12.91 0.00 9.51 -0.00 -2.97
16 77 -0.00 -12.94 0.00 2.99 -0.00 0.88
66 0.00 15.93 0.00 16.54 0.00 -0.88
17 77 -0.00 -10.93 0.00 4.94 -0.00 -0.94
66 0.00 13.92 0.00 11.85 -0.00 0.94
18 77 -0.00 -7.90 0.00 7.85 0.00 1.16
66 0.00 10.89 0.00 4.80 -0.00 -1.16

117 7 63 0.00 7.34 0.00 -5.01 0.00 -0.33

64 -0.00 6.74 0.00 3.84 -0.00 0.33
8 63 -0.00 9.45 0.00 -6.63 -0.00 -0.51
64 0.00 8.60 0.00 4.94 -0.00 0.51
11 63 0.00 7.49 0.00 -5.39 0.00 -0.78
64 -0.00 6.45 0.00 3.44 -0.00 0.78
12 63 0.00 4.39 0.00 0.02 -0.00 -0.14
64 -0.00 9.56 0.00 9.04 -0.00 0.14
13 63 0.00 7.11 0.00 -4.72 0.00 0.22
64 -0.00 6.84 0.00 4.12 -0.00 -0.22
14 63 -0.00 10.21 0.00 -10.13 -0.00 -0.43
64 0.00 3.73 0.00 -1.48 -0.00 0.43
15 63 0.00 4.93 0.00 -3.58 0.00 -0.64
64 -0.00 4.13 0.00 2.10 -0.00 0.64

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 61 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 62

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE (GLOBAL)

MEMBER LOAD JT FX FY FZ MX MY MZ

16 63 0.00 1.82 0.00 1.83 -0.00 0.01

64 -0.00 7.23 0.00 7.70 -0.00 -0.01
17 63 0.00 4.55 0.00 -2.91 0.00 0.36
64 -0.00 4.51 0.00 2.78 -0.00 -0.36
18 63 -0.00 7.65 0.00 -8.32 -0.00 -0.29
64 0.00 1.41 0.00 -2.82 -0.00 0.29

************** END OF LATEST ANALYSIS RESULT **************

168. FINISH

*********** END OF THE STAAD.Pro RUN ***********

**** DATE= MAY 17,2024 TIME= 15:35:55 ****

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 62 of 63
 Friday, 17 May 2024 3:35 pm

DXF IMPORT OF DRAWING1.DXF -- PAGE NO. 63

************************************************************
* For technical assistance on STAAD.Pro, please visit *
* http://www.bentley.com/en/support/ *
* *
* Details about additional assistance from *
* Bentley and Partners can be found at program menu *
* Help->Technical Support *
* *
* Copyright (c) 1997-2017 Bentley Systems, Inc. *
* http://www.bentley.com *
************************************************************

C:\Users\user\Desktop\francis\SIDELINE\JOSHUA~1\CONCEP~1\Structure1.anl Page 63 of 63
 SEISMIC ANALYSIS
Design Parameters
No. of Storey 2
Soil Profile Type = D
Seimic Zone = 0.4
Rwx = 8.5 Numerical Coefficient for Structural Systems
Rwz = 8.5 Numerical Coefficient for Structural Systems
Na = 1.2 Near Source Factor (see table)
Nv = 1.6 Near Source Factor (see table)
Ct = 0.0731
hn = 7.1
I= 1 Importance Factor
W = 1594.50 Total Weight of Dead Loads
Ca = 0.44 Seismic Coefficient (see table)
Cv = 0.64 Seismic Coefficient (see table)
Ta = Cthn3/4 0.31795
5% Accidental
T = 1.3*Ta < Tb 0.41334 Structural Period for Design Dim. of Building Along Torsion
Level X Z X Z
Design of Base Shear
V = Cv IW/RT = 377.593 kN Total Design Base Shear
Vmax = 2.5CaIW/R = 206.347 kN Total Design Base Shear Shall not Exceed
Vmin1 = 0.11*CaIW = 77.1738 kN Total Design Base Shear Shall not be less than
Vmin2 = 0.8ZNv IW/R 96.0452 kN Total Design Base Shear Shall not be less than ROOF 11.662 13.776 0.5831 0.6888
Governing Base Shear (V) 206.347 kN 2FL 11.662 13.776 0.5831 0.6888

Ft = - Ft = 0.07TV < 0.25V i f T i s more tha n 0.7s ec, Ft = 0 i f T i s l es s tha n 0.7s ec

Floor Level Center of Rigidity Center of Mass W/ 5% Accidental Torsion

X Z X Z +X -X +Z -Z

ROOF 5.386 5.354 4.9440 5.081 0.14 -1.025 0.42 -0.96

2FL 5.394 5.256 4.844 5.197 0.03 -1.133 0.63 -0.75

Fx (kN)
Fx (kN)
Torsion-Z Torsion-X
Floor Level hi (m) Wi (kN) Wihi Storey eX (m) ez(m)
(kN-m) (kN-m)
Shear

69.470
6 ROOF 6 402.42 2414.52 69.47 1.03 -71.21 0.96 -66.82
136.87
3.45 2FL 3.45 1378.72 4757.00 136.87 1.13 -1.13 0.75 -102.35

SUM 1781.14 7171.52 206.34

IX. DESIGN OF STRUCTURAL
MEMBERS
 DESIGN OF SLAB
PROJECT NAME : CONCEPCION RESIDENCE PREPARED BY : FSL
SUBJECT : S-2 DATE : 18/11/2023

Lx ( SECTION ALONG Lx
LONGER )
10mm bar @ 150 mm O.C. (A) 10mm bar @ 150 mm O.C. (B)
TB_(D)

BB_(E)
Ly (SHORTER)

BB_(F)

TB_(A) 10mm bar @ 300 mm O.C. (E)

TB_(B)

SECTION ALONG Ly
TB_(C)

10mm bar @ 150 mm O.C. (C) 10mm bar @ 150 mm O.C. (D)

10mm bar @ 300 mm O.C. (F)

PLAN

SLAB SLAB REINFORCEMENT ALONG LENGTH Lx REINFORCEMENT ALONG LENGTH Ly

THICKNESS, t REINFORCEMENT CONTINUOUS END DISCONTINUOS END CONTINUOUS END DISCONTINUOS END

TOP BAR (TB) 10mm bar @ 150 mm O.C. ----- 10mm bar @ 150 mm O.C. -----
100 mm
BOT. BAR (BB) 10mm bar @ 300 mm O.C. 10mm bar @ 300 mm O.C.

SLAB GEOMETRY TWO-WAY SLAB LOADINGS:

Slab Edge Condition Case No. = 2.0 Finishings WFIN = 1.67 kPa
Clear Span along X Lx = 4.4 m Miscellaneous WMISC = 0.50 kPa
Clear Span along Y Ly = 3.2 m Superimposed Live WLL = 1.90 kPa
Slab thickness t = 100 mm Percent LL Sustained LL% = 25%
Clear Cover cc = 25 mm Long Term Deflection Duration = 60 month

MATERIAL PROPERTIES :
MOMENT COEFFICIENTS Concrete Comp. Strength f'c = 21.0 MPa
Positive Coeff. Negative Coeff. Steel Yield Strength fy = 230.0 MPa
Dead Cs = 0.030 DL + LL Cs = 0.074 Modulus of Elasticity Ec = 21538 MPa
Cl = 0.007 DL + LL Cl = 0.027 Modulus of Elasticity Es = 200000 MPa
Live Cs = 0.049 BEAM DATA
Cl = M = C W L2
0.012 MARK B1 (LEFT) B2 (RIGHT) B3 (TOP) B4 (BELOW)
RATIO Width, b 200 200 200 200
m = LS / LL b = LL / LS Depth, d 400 400 400 400
= 0.70 = 1.38 Note : Beam Sizes to be used for minimum slab thickness
comuptation

FLEXURE DESIGN
BEAMS SLAB
Ecb Ib/EcsIs
Slab Clear Spans: MARK Inertia, Ib MARK Inertia, IS
Shorter Span LS = 3.15 m BL 1066.67 SL 362.50 2.94
Longer Span LL = 4.35 m BR 1066.67 SR 362.50 2.94
BU 1066.67 SU 262.50 4.06
Minimum Slab Thickness Required BB 1066.67 SB 262.50 4.06
if Two-way Slab Note : All values are in x10 6 mm 4 S 14.01
tm in = LL ( 0.8+ fy /1400 )/(36 + a)
= 86.62 mm a fm = S ( Ecb Ib / Ecs Is ) / 4
or 90.0 mm = 3.50 > 2.0
if One-way Slab For Two-way slab
tm in = (0.40+fy/700) LS / 28 a = 5b ( afm - 0.20) if a fm < 2.0 & >0.22
= 81.96 mm = 9b if a fm > 2.0
Then : For One-way Slab
tm in = 90.00 mm < tprov (OK!!!) if fy = 420MPa, then (0.40+fy/700) = 1.0
Loadings Factored Loads
Deadload LF
Slab Weight Ws = 2.35 kPa WuDEAD = 1.20 x WDL = 5.43 kPa
Finishings WF = 1.67 kPa WuLIVE = 1.60 x WLL = 3.04 kPa
Miscellaneous WM = 0.50 kPa WuTOT = Wu(DL+LL) = 8.47 kPa
Total Deadload WDL = WS + W F + WM
= 4.52 kPa
Liveload
WLL = 1.90 kPa

Reinforcment Calculation :

Along Length Lx ( Longer Direction ) d = 60.0 mm b = 1000.0 mm

2
Positive Moment +Mu = Cl WuTOT Lx = 1.41 kN-m ( For Bottom Bar )

Rn = Mu / (0.90 b d2) = 0.43 kN-m

Steel Ratio r = [1-(1- 2Rn/0.85f'c) 1/2] (0.85f'c/fy) = 0.0019 < r min = 0.0020

Steel Area As = rbd = 120.0 mm 2

Max. Spacing (smaller of)
Max. Spacing Req'd s = Ab / As ( b ) = 650 mm > 3t= 300 mm
> or 450 mm

2
Negative Moment - Mu = Cl WuTOT Ly = 4.33 kN-m ( For Top Bar )

Rn = Mu / (0.90 b d2) = 1.34

Steel Ratio r = [1-(1- 2Rn/0.85f'c) 1/2] (0.85f'c/fy) = 0.0060 > r min = 0.0020

Steel Area As = rbd = 362.5 mm 2

Max. Spacing (smaller of)
Max. Spacing Req'd s = Ab / As ( b ) = 200.0 mm < 3t= 300 mm
< or 450 mm

Along Length Ly (Shorter Direction ) d = 70.0 mm b = 1000.0 mm

2
Positive Moment +Mu Cs WuTOT Ly = 3.09 kN-m ( For Bottom Bar )

Rn = Mu / (0.90 b d2) = 0.70

1/2
Steel Ratio r = [1-(1- 2Rn/0.85f'c) ] (0.85f'c/fy) = 0.0031 > r min = 0.0020

Steel Area As = rbd = 217.90 mm 2

Max. Spacing (smaller of)
Max. Spacing Req'd s = Ab / As ( b ) = 350 mm > 3t= 300 mm
< or 450 mm

2
Negative Moment - Mu Cs WuTOT Ly = 6.22 kN-m ( For Top Bar )

Rn = Mu / (0.90 b d2) = 1.41

Steel Ratio r = [1-(1- 2Rn/0.85f'c) 1/2] (0.85f'c/fy) = 0.0064 > r min = 0.0020

Steel Area As = rbd = 447.59 mm 2

Max. Spacing (smaller of)
Max. Spacing Req'd s = Ab / As ( b ) = 175 mm < 3t= 300 mm
< or 450 mm
DEFLECTION CHECK ( LONG-TERM )

Modular Ratio n = Es/Ec = 9.29

Rupture Strength fr = 0.70 (f'c)1/2 = 3.21 MPa

Dead Load
Along Length Lx
1 MDX Lx2 MDx = WDL ( Lx )2 Cl
D DLX =
16 Ec Ieff = 0.599 kN-m
= 0.395 mm
Along Length Ly Average Deflection
1 MDY Ly
2
MDY =
2
WDL ( Ly ) Cs D DL = (D DLX + D DLY ) / 2
D DLY =
16 Ec Ieff = 1.347 kN-m = 0.430 mm
= 0.465 mm

Live Load
Along Length Lx
3 ML Lx2 MLX = WLL ( Lx )2 Cl
D LLX =
32 Ec Ieff = 0.431 kN-m
= 0.426 mm
Along Length Ly Average Deflection
3 ML Ly
2
MLY =
2
WLL ( Ly ) Cs D DL = ( D LLX + D LLY ) / 2
D LLY =
32 Ec Ieff = 0.924 kN-m = 0.453 mm
= 0.479 mm

Moment due to Dead and Live

MDL + LL = Max ( MDX+MLX , MDY+MLY )
= 2.27 kN-m
Sustained Moment
Msustained = Max ( MDX+(LL%)MLX , MDY+(LL%)MLY )
= 1.58 kN-m

Neutral Axis b kd2 + nAs kd + nAs d kd = 20.74 mm

Cracked Moment of Inertia, Icr

Icr = (b*kd3/3 + nAs (b/s) (d - kd)2
6 4
= 12.50 x10 mm
Gross Moment of Inertia, Igross
3
Igross = b t /12
= 83.33 x10 6 mm 4
Cracked Moment, Mcr
Mcr = fr Ig / (t/2)
= 5.35 kN-m

A. DEADLOAD only
MDY/Mcr = 0.25
Effective Moment of Inertia, Ie
Ie = Ig
= 83.33 x10 6 mm 4
D i(D) = 0.43 mm
B. SUSTAINED LOAD
Msus/Mcr = 0.30
Ie = Ig
= 83.33 x10 6 mm 4
D i(SUS) = 1.58 mm
C. DEADLOAD + LIVELOAD
Mdl+ll/Mcr = 0.42
Ie = Ig
= 83.33 x10 6 mm 4
D i(DL+LL) = 2.27 mm
D. LONG-TERM DEFLECTION
e = 2.00 ( Time-dependent Coefficient )
l = e / ( 1 + 50r' )
= 1.71

D i(LL) = D i(DL+LL) - D i(DL) = 1.84 mm

l D i(SUS) = D i(SUS) ( 1+l ) = 4.27 mm

D i(TOT) = Di(LL) + lD(SUS)

= 6.11 mm < L / 240 = 13.13 mm ( OK!!! )
PROJECT NAME : CONCEPCION RESIDENCE PREPARED BY : FSL
SUBJECT : S-1 DATE : 18/11/2023

Lx ( SECTION ALONG Lx
LONGER )
10mm bar @ 300 mm O.C. (A) 10mm bar @ 300 mm O.C. (B)

TB_(D)
Ly (SHORTER)

BB_(E)
10mm bar @ 300 mm O.C. (E)
BB_(F)

TB_(A) TB_(B)
TB_(C)

SECTION ALONG Ly
10mm bar @ 300 mm O.C. (C) 10mm bar @ 300 mm O.C. (D)

10mm bar @ 300 mm O.C. (F)

PLAN

SLAB SLAB REINFORCEMENT ALONG LENGTH Lx REINFORCEMENT ALONG LENGTH Ly

THICKNESS, t REINFORCEMENT CONTINUOUS END DISCONTINUOS END CONTINUOUS END DISCONTINUOS END

TOP BAR (TB) 10mm bar @ 300 mm O.C. ----- 10mm bar @ 300 mm O.C. -----
100 mm
BOT. BAR (BB) 10mm bar @ 300 mm O.C. 10mm bar @ 300 mm O.C.

SLAB GEOMETRY ONE-WAY SLAB LOADINGS:

Slab Edge Condition Case No. = 2.0 Finishings WFIN = 1.67 kPa
Clear Span along X Lx = 3.0 m Miscellaneous WMISC = 0.50 kPa
Clear Span along Y Ly = 0.9 m Superimposed Live WLL = 1.90 kPa
Slab thickness t = 100 mm Percent LL Sustained LL% = 25%
Clear Cover cc = 25 mm Long Term Deflection Duration = 60 month

MATERIAL PROPERTIES :
MOMENT COEFFICIENTS Concrete Comp. Strength f'c = 20.7 MPa
Positive Coeff. Negative Coeff. Steel Yield Strength fy = 230.0 MPa
Dead Cs = 0.042 DL + LL Cs = 0.083 Modulus of Elasticity Ec = 21384 MPa
Cl = 0.000 DL + LL Cl = 0.000 Modulus of Elasticity Es = 200000 MPa
Live Cs = 0.042 2
BEAM DATA
Cl = M=CWL
0.000 MARK B1 (LEFT) B2 (RIGHT) B3 (TOP) B4 (BELOW)
RATIO Width, b 200 200 200 200
m = LS / LL b = LL / LS Depth, d 400 400 400 400
= 0.30 = 3.28 Note : Beam Sizes to be used for minimum slab thickness
comuptation

FLEXURE DESIGN
BEAMS SLAB
Ecb Ib/EcsIs
Slab Clear Spans: MARK Inertia, Ib MARK Inertia, IS
Shorter Span LS = 0.90 m BL 1066.67 SL 245.83 4.34
Longer Span LL = 2.95 m BR 1066.67 SR 245.83 4.34
BU 1066.67 SU 75.00 14.22
Minimum Slab Thickness Required BB 1066.67 SB 75.00 14.22
if Two-way Slab Note : All values are in x10 6 mm 4 S 37.12
tm in = LL ( 0.8+ fy /1400 )/(36 + a)
= 43.43 mm a fm = S ( Ecb Ib / Ecs Is ) / 4
or 90.0 mm = 9.28 > 2.0
if One-way Slab For Two-way slab
tm in = (0.40+fy/700) LS / 28 a = 5b ( afm - 0.20) if a fm < 2.0 & >0.22
= 23.42 mm = 9b if a fm > 2.0
Then : For One-way Slab
tm in = 23.42 mm < tprov (OK!!!) if fy = 420MPa, then (0.40+fy/700) = 1.0
Loadings Factored Loads
Deadload LF
Slab Weight Ws = 2.35 kPa WuDEAD = 1.20 x WDL = 5.43 kPa
Finishings WF = 1.67 kPa WuLIVE = 1.60 x WLL = 3.04 kPa
Miscellaneous WM = 0.50 kPa WuTOT = Wu(DL+LL) = 8.47 kPa
Total Deadload WDL = WS + W F + WM
= 4.52 kPa
Liveload
WLL = 1.90 kPa

Reinforcment Calculation :

Along Length Lx ( Longer Direction ) d = 60.0 mm b = 1000.0 mm

2
Positive Moment +Mu = Cl WuTOT Lx = 0.00 kN-m ( For Bottom Bar )

Rn = Mu / (0.90 b d2) = 0.00 kN-m

Steel Ratio r = [1-(1- 2Rn/0.85f'c) 1/2] (0.85f'c/fy) = 0.0000 < r min = 0.0020

Steel Area As = rbd = 120.0 mm 2

Max. Spacing (smaller of)
Max. Spacing Req'd s = Ab / As ( b ) = 650 mm > 3t= 300 mm
> or 450 mm

2
Negative Moment - Mu = Cl WuTOT Ly = 0.00 kN-m ( For Top Bar )

Rn = Mu / (0.90 b d2) = 0.00

Steel Ratio r = [1-(1- 2Rn/0.85f'c) 1/2] (0.85f'c/fy) = 0.0000 < r min = 0.0020

Steel Area As = rbd = 120.0 mm 2

Max. Spacing (smaller of)
Max. Spacing Req'd s = Ab / As ( b ) = 650.0 mm > 3t= 300 mm
> or 450 mm

Along Length Ly (Shorter Direction ) d = 70.0 mm b = 1000.0 mm

2
Positive Moment +Mu Cs WuTOT Ly = 0.29 kN-m ( For Bottom Bar )

Rn = Mu / (0.90 b d2) = 0.06

1/2
Steel Ratio r = [1-(1- 2Rn/0.85f'c) ] (0.85f'c/fy) = 0.0003 < r min = 0.0020

Steel Area As = rbd = 140.00 mm 2

Max. Spacing (smaller of)
Max. Spacing Req'd s = Ab / As ( b ) = 550 mm > 3t= 300 mm
> or 450 mm

2
Negative Moment - Mu Cs WuTOT Ly = 0.57 kN-m ( For Top Bar )

Rn = Mu / (0.90 b d2) = 0.13

Steel Ratio r = [1-(1- 2Rn/0.85f'c) 1/2] (0.85f'c/fy) = 0.0006 < r min = 0.0020

Steel Area As = rbd = 140.00 mm 2

Max. Spacing (smaller of)
Max. Spacing Req'd s = Ab / As ( b ) = 550 mm > 3t= 300 mm
> or 450 mm
DEFLECTION CHECK ( LONG-TERM )

Modular Ratio n = Es/Ec = 9.35

Rupture Strength fr = 0.70 (f'c)1/2 = 3.18 MPa

Dead Load
Along Length Lx
1 MDX Lx2 MDx = WDL ( Lx )2 Cl
D DLX =
16 Ec Ieff = 0.000 kN-m
= 0.000 mm
Along Length Ly Average Deflection
1 MDY Ly
2
MDY =
2
WDL ( Ly ) Cs D DL = (D DLX + D DLY ) / 2
D DLY =
16 Ec Ieff = 0.153 kN-m = 0.002 mm
= 0.004 mm

Live Load
Along Length Lx
3 ML Lx2 MLX = WLL ( Lx )2 Cl
D LLX =
32 Ec Ieff = 0.000 kN-m
= 0.000 mm
Along Length Ly Average Deflection
3 ML Ly
2
MLY =
2
WLL ( Ly ) Cs D DL = ( D LLX + D LLY ) / 2
D LLY =
32 Ec Ieff = 0.064 kN-m = 0.001 mm
= 0.003 mm

Moment due to Dead and Live

MDL + LL = Max ( MDX+MLX , MDY+MLY )
= 0.22 kN-m
Sustained Moment
Msustained = Max ( MDX+(LL%)MLX , MDY+(LL%)MLY )
= 0.17 kN-m

Neutral Axis b kd2 + nAs kd + nAs d kd = 15.56 mm

Cracked Moment of Inertia, Icr

Icr = (b*kd3/3 + nAs (b/s) (d - kd)2
6 4
= 7.24 x10 mm
Gross Moment of Inertia, Igross
3
Igross = b t /12
= 83.33 x10 6 mm 4
Cracked Moment, Mcr
Mcr = fr Ig / (t/2)
= 5.31 kN-m

A. DEADLOAD only
MDY/Mcr = 0.03
Effective Moment of Inertia, Ie
Ie = Ig
= 83.33 x10 6 mm 4
D i(D) = 0.00 mm
B. SUSTAINED LOAD
Msus/Mcr = 0.03
Ie = Ig
= 83.33 x10 6 mm 4
D i(SUS) = 0.17 mm
C. DEADLOAD + LIVELOAD
Mdl+ll/Mcr = 0.04
Ie = Ig
= 83.33 x10 6 mm 4
D i(DL+LL) = 0.22 mm
D. LONG-TERM DEFLECTION
e = 2.00 ( Time-dependent Coefficient )
l = e / ( 1 + 50r' )
= 1.80

D i(LL) = D i(DL+LL) - D i(DL) = 0.21 mm

l D i(SUS) = D i(SUS) ( 1+l ) = 0.47 mm

D i(TOT) = Di(LL) + lD(SUS)

= 0.69 mm < L / 240 = 3.75 mm ( OK!!! )
 DESIGN OF BEAMS
REINFORCED CONCRETE BEAM
RB-1
Input Parameters :
Sup Mid
Standard Specs Moment Capacity Top Bot Shear Capacity
fc' = 21 Mpa Tension Bar, Dt = 3 3 bw = 200 mm fyt = 230
fy = 275 Mpa Tension Bar 2-L, Nb = 0 0 h = 300 mm Av = 2
b₁ = .85 Compression Bar, Dc = 2 2 Sb = 10 mm Stirrups Bar Ø
Es = 200 Gpa Main Bar dia, D = 16 Cc = 40 mm, Clear Covering
Moment, Mu = 16.2 15.5
CONDITION : Val = 0.65+0.25 (Ԑt - Ԑty/0.005 - Ԑty) S
Ø = 0.65 , Ԑt ≤ Ԑty 3-16mmØ
Val , Ԑty ˂ Ԑt ˂ 0.005 -- -- --
U
0.90 , Ԑt ≥ 0.005 P
Location of d' & dt; Support Midspan P
As1 = π D² Db /4 = 603.19 603.19 O
2L, As2 = π D² Nb /4 = 0.00 0.00
y = (As 1 y1+As 2 y2)/As = 0.00 0.00 2-16mmØ
R
d' = Cc + Sb + (D/2) + y = 58.00 58.00 T
dt = h - d' = 242.00 242.00
CHECKING : εt ≥ 0.004, Support Midspan
Cma x = 600 d t / fsmin +600 = 103.7 103.71 M
ama x = β1 Cmax = 88.2 88.16 2-16mmØ
I
Asma x = 0.85f'c a max b w / fy = 1144.44 1144.44
a = (As fy- As' fy)/0.85 fc' b = 46.46 46.46 D
C= a/β1 = 54.66 54.66 S
fs' = 600 (C-d')/C = -36.62 -36.62 P
fs' = Compression Bars = Not Yield Not Yield -- -- --
3-16mmØ
A
fs = 600 (dt-C)/C = 2056.26 2056.26
fs = Tension Bars = Yield Yield N
BEAM MOMENT CAPACITY; Ø = 0.9 CHECK SHEAR; Ø = 0.75
As fy = 0.85fc' β1 C bw + As' fs'; Where, fs' = (600 C-d'/C) Vc = 0.17 √fc' bw dt = 38 < 75.00
Support Midspan Vsmax = 0.67 √fc' bw dt = 149 KN
C= by quadratic = 56.66 56.66 Vs = (Vu/Ø ) - Vc = 62.29 < 148.60
a= β1 C = 48.16 48.16 Section is Adequate
fs' = 600 (C-d')/C = -14.19 -14.19 Av = 2 (π Sb²/4)= 157.1
fs = 600 (dt-C)/C = 1962.65 1962.65 Vs ≤ 0.33√f'c bw d, d/2
Max S, w/c
Mn =Cc[d t -(a/2)] + Cs (d t -d')= 36.42 36.42 or 600mm otherwise
ever is
SUPPORT, ØMn = 32.78 > 16.20 Pass!
lesser,mm
Vs > 0.33√f'c bw d,
MIDSPAN, ØMn = 32.78 > 15.45 Pass! d/4 or 300mm

Therefore use 200x300with 5-16mmØ @ support and 5-16mmØ @ midspan Main Bars (Grade 40);
10mmØ 2 leg-stirrups: Sp. at 2@50, 10@60 and rest 200 O.C
 REINFORCED CONCRETE BEAM
RB-2
Input Parameters :
Sup Mid
Standard Specs Moment Capacity Top Bot Shear Capacity
fc' = 21 Mpa Tension Bar, Dt = 2 2 bw = 200 mm fyt = 230
fy = 275 Mpa Tension Bar 2-L, Nb = 2 2 h = 400 mm Av = 2
b₁ = .85 Compression Bar, Dc = 2 2 Sb = 10 mm Stirrups Bar Ø
Es = 200 Gpa Main Bar dia, D = 16 Cc = 40 mm, Clear Covering
Moment, Mu = 31.2 36.9
CONDITION : Val = 0.65+0.25 (Ԑt - Ԑty/0.005 - Ԑty) S
Ø = 0.65 , Ԑt ≤ Ԑty 2-16mmØ
Val , Ԑty ˂ Ԑt ˂ 0.005 2-16mmØ
U
0.90 , Ԑt ≥ 0.005 P
Location of d' & dt; Support Midspan P
As1 = π D² Db /4 = 402.12 402.12 O
2L, As2 = π D² Nb /4 = 402.12 402.12
y = (As 1 y1+As 2 y2)/As = 30.00 30.00 2-16mmØ
R
d' = Cc + Sb + (D/2) + y = 88.00 88.00 T
dt = h - d' = 312.00 312.00
CHECKING : εt ≥ 0.004, Support Midspan
Cma x = 600 d t / fsmin +600 = 133.7 133.71 M
ama x = β1 Cmax = 113.7 113.66 2-16mmØ
I
Asma x = 0.85f'c a max b w / fy = 1475.48 1475.48
a = (As fy- As' fy)/0.85 fc' b = 61.95 61.95 D
C= a/β1 = 72.88 72.88 S
fs' = 600 (C-d')/C = -124.43 -124.43 P
fs' = Compression Bars = Not Yield Not Yield 2-16mmØ
2-16mmØ
A
fs = 600 (dt-C)/C = 1968.45 1968.45
fs = Tension Bars = Yield Yield N
BEAM MOMENT CAPACITY; Ø = 0.9 CHECK SHEAR; Ø = 0.75
As fy = 0.85fc' β1 C bw + As' fs'; Where, fs' = (600 C-d'/C) Vc = 0.17 √fc' bw dt = 49 < 75.00
Support Midspan Vsmax = 0.67 √fc' bw dt = 192 KN
C= by quadratic = 80.40 80.40 Vs = (Vu/Ø ) - Vc = 51.39 < 191.59
a= β1 C = 68.34 68.34 Section is Adequate
fs' = 600 (C-d')/C = -56.68 -56.68 Av = 2 (π Sb²/4)= 157.1
fs = 600 (dt-C)/C = 1728.24 1728.24 Vs ≤ 0.33√f'c bw d, d/2
Max S, w/c
Mn =Cc[d t -(a/2)] + Cs (d t -d')= 62.68 62.68 or 600mm otherwise
ever is
SUPPORT, ØMn = 56.41 > 31.17 Pass!
lesser,mm
Vs > 0.33√f'c bw d,
MIDSPAN, ØMn = 56.41 > 36.88 Pass! d/4 or 300mm

Therefore use 200x400with 6-16mmØ @ support and 6-16mmØ @ midspan Main Bars (Grade 40);
10mmØ 2 leg-stirrups: Sp. at 2@50, 10@70 and rest 200 O.C
 REINFORCED CONCRETE BEAM
B-1
Input Parameters :
Sup Mid
Standard Specs Moment Capacity Top Bot Shear Capacity
fc' = 21 Mpa Tension Bar, Dt = 3 3 bw = 200 mm fyt = 230
fy = 275 Mpa Tension Bar 2-L, Nb = 3 3 h = 450 mm Av = 2
b₁ = .85 Compression Bar, Dc = 3 3 Sb = 10 mm Stirrups Bar Ø
Es = 200 Gpa Main Bar dia, D = 16 Cc = 40 mm, Clear Covering
Moment, Mu = 85.4 71.7
CONDITION : Val = 0.65+0.25 (Ԑt - Ԑty/0.005 - Ԑty) S
Ø = 0.65 , Ԑt ≤ Ԑty 3-16mmØ
Val , Ԑty ˂ Ԑt ˂ 0.005 3-16mmØ
U
0.90 , Ԑt ≥ 0.005 P
Location of d' & dt; Support Midspan P
As1 = π D² Db /4 = 603.19 603.19 O
2L, As2 = π D² Nb /4 = 603.19 603.19
y = (As 1 y1+As 2 y2)/As = 30.00 30.00 3-16mmØ
R
d' = Cc + Sb + (D/2) + y = 88.00 88.00 T
dt = h - d' = 362.00 362.00
CHECKING : εt ≥ 0.004, Support Midspan
Cma x = 600 d t / fsmin +600 = 155.1 155.14 M
ama x = β1 Cmax = 131.9 131.87 3-16mmØ
I
Asma x = 0.85f'c a max b w / fy = 1711.93 1711.93
a = (As fy- As' fy)/0.85 fc' b = 92.93 92.93 D
C= a/β1 = 109.33 109.33 S
fs' = 600 (C-d')/C = 117.04 117.04 P
fs' = Compression Bars = Not Yield Not Yield 3-16mmØ
3-16mmØ
A
fs = 600 (dt-C)/C = 1386.70 1386.70
fs = Tension Bars = Yield Yield N
BEAM MOMENT CAPACITY; Ø = 0.9 CHECK SHEAR; Ø = 0.75
As fy = 0.85fc' β1 C bw + As' fs'; Where, fs' = (600 C-d'/C) Vc = 0.17 √fc' bw dt = 56 < 75.00
Support Midspan Vsmax = 0.67 √fc' bw dt = 222 KN
C= by quadratic = 97.65 97.65 Vs = (Vu/Ø ) - Vc = 43.60 < 222.29
a= β1 C = 83.01 83.01 Section is Adequate
fs' = 600 (C-d')/C = 59.32 59.32 Av = 2 (π Sb²/4)= 157.1
fs = 600 (dt-C)/C = 1624.18 1624.18 Vs ≤ 0.33√f'c bw d, d/2
Max S, w/c
Mn =Cc[d t -(a/2)] + Cs (d t -d')= 104.78 104.78 or 600mm otherwise
ever is
SUPPORT, ØMn = 94.30 > 85.39 Pass!
lesser,mm
Vs > 0.33√f'c bw d,
MIDSPAN, ØMn = 94.30 > 71.70 Pass! d/4 or 300mm

Therefore use 200x450with 8-16mmØ @ support and 8-16mmØ @ midspan Main Bars (Grade 40);
10mmØ 2 leg-stirrups: Sp. at 2@50, 10@90 and rest 200 O.C
 REINFORCED CONCRETE BEAM
B-2
Input Parameters :
Sup Mid
Standard Specs Moment Capacity Top Bot Shear Capacity
fc' = 21 Mpa Tension Bar, Dt = 3 3 bw = 200 mm fyt = 230
fy = 275 Mpa Tension Bar 2-L, Nb = 2 2 h = 400 mm Av = 2
b₁ = .85 Compression Bar, Dc = 3 3 Sb = 10 mm Stirrups Bar Ø
Es = 200 Gpa Main Bar dia, D = 16 Cc = 40 mm, Clear Covering
Moment, Mu = 54.2 64.1
CONDITION : Val = 0.65+0.25 (Ԑt - Ԑty/0.005 - Ԑty) S
Ø = 0.65 , Ԑt ≤ Ԑty 3-16mmØ
Val , Ԑty ˂ Ԑt ˂ 0.005 2-16mmØ
U
0.90 , Ԑt ≥ 0.005 P
Location of d' & dt; Support Midspan P
As1 = π D² Db /4 = 603.19 603.19 O
2L, As2 = π D² Nb /4 = 402.12 402.12
y = (As 1 y1+As 2 y2)/As = 24.00 24.00 3-16mmØ
R
d' = Cc + Sb + (D/2) + y = 82.00 82.00 T
dt = h - d' = 318.00 318.00
CHECKING : εt ≥ 0.004, Support Midspan
Cma x = 600 d t / fsmin +600 = 136.3 136.29 M
ama x = β1 Cmax = 115.8 115.84 3-16mmØ
I
Asma x = 0.85f'c a max b w / fy = 1503.85 1503.85
a = (As fy- As' fy)/0.85 fc' b = 77.44 77.44 D
C= a/β1 = 91.11 91.11 S
fs' = 600 (C-d')/C = 59.97 59.97 P
fs' = Compression Bars = Not Yield Not Yield 2-16mmØ
3-16mmØ
A
fs = 600 (dt-C)/C = 1494.27 1494.27
fs = Tension Bars = Yield Yield N
BEAM MOMENT CAPACITY; Ø = 0.9 CHECK SHEAR; Ø = 0.75
As fy = 0.85fc' β1 C bw + As' fs'; Where, fs' = (600 C-d'/C) Vc = 0.17 √fc' bw dt = 50 < 75.00
Support Midspan Vsmax = 0.67 √fc' bw dt = 195 KN
C= by quadratic = 85.75 85.75 Vs = (Vu/Ø ) - Vc = 50.45 < 195.27
a= β1 C = 72.88 72.88 Section is Adequate
fs' = 600 (C-d')/C = 26.22 26.22 Av = 2 (π Sb²/4)= 157.1
fs = 600 (dt-C)/C = 1625.15 1625.15 Vs ≤ 0.33√f'c bw d, d/2
Max S, w/c
Mn =Cc[d t -(a/2)] + Cs (d t -d')= 76.99 76.99 or 600mm otherwise
ever is
SUPPORT, ØMn = 69.29 > 54.20 Pass!
lesser,mm
Vs > 0.33√f'c bw d,
MIDSPAN, ØMn = 69.29 > 64.06 Pass! d/4 or 300mm

Therefore use 200x400with 7-16mmØ @ support and 7-16mmØ @ midspan Main Bars (Grade 40);
10mmØ 2 leg-stirrups: Sp. at 2@50, 10@70 and rest 200 O.C
 REINFORCED CONCRETE BEAM
B-3
Input Parameters :
Sup Mid
Standard Specs Moment Capacity Top Bot Shear Capacity
fc' = 21 Mpa Tension Bar, Dt = 2 2 bw = 200 mm fyt = 230
fy = 275 Mpa Tension Bar 2-L, Nb = 2 2 h = 400 mm Av = 2
b₁ = .85 Compression Bar, Dc = 2 2 Sb = 10 mm Stirrups Bar Ø
Es = 200 Gpa Main Bar dia, D = 16 Cc = 40 mm, Clear Covering
Moment, Mu = 46.8 38.9
CONDITION : Val = 0.65+0.25 (Ԑt - Ԑty/0.005 - Ԑty) S
Ø = 0.65 , Ԑt ≤ Ԑty 2-16mmØ
Val , Ԑty ˂ Ԑt ˂ 0.005 2-16mmØ
U
0.90 , Ԑt ≥ 0.005 P
Location of d' & dt; Support Midspan P
As1 = π D² Db /4 = 402.12 402.12 O
2L, As2 = π D² Nb /4 = 402.12 402.12
y = (As 1 y1+As 2 y2)/As = 30.00 30.00 2-16mmØ
R
d' = Cc + Sb + (D/2) + y = 88.00 88.00 T
dt = h - d' = 312.00 312.00
CHECKING : εt ≥ 0.004, Support Midspan
Cma x = 600 d t / fsmin +600 = 133.7 133.71 M
ama x = β1 Cmax = 113.7 113.66 2-16mmØ
I
Asma x = 0.85f'c a max b w / fy = 1475.48 1475.48
a = (As fy- As' fy)/0.85 fc' b = 61.95 61.95 D
C= a/β1 = 72.88 72.88 S
fs' = 600 (C-d')/C = -124.43 -124.43 P
fs' = Compression Bars = Not Yield Not Yield 2-16mmØ
2-16mmØ
A
fs = 600 (dt-C)/C = 1968.45 1968.45
fs = Tension Bars = Yield Yield N
BEAM MOMENT CAPACITY; Ø = 0.9 CHECK SHEAR; Ø = 0.75
As fy = 0.85fc' β1 C bw + As' fs'; Where, fs' = (600 C-d'/C) Vc = 0.17 √fc' bw dt = 49 < 75.00
Support Midspan Vsmax = 0.67 √fc' bw dt = 192 KN
C= by quadratic = 80.40 80.40 Vs = (Vu/Ø ) - Vc = 51.39 < 191.59
a= β1 C = 68.34 68.34 Section is Adequate
fs' = 600 (C-d')/C = -56.68 -56.68 Av = 2 (π Sb²/4)= 157.1
fs = 600 (dt-C)/C = 1728.24 1728.24 Vs ≤ 0.33√f'c bw d, d/2
Max S, w/c
Mn =Cc[d t -(a/2)] + Cs (d t -d')= 62.68 62.68 or 600mm otherwise
ever is
SUPPORT, ØMn = 56.41 > 46.85 Pass!
lesser,mm
Vs > 0.33√f'c bw d,
MIDSPAN, ØMn = 56.41 > 38.94 Pass! d/4 or 300mm

Therefore use 200x400with 6-16mmØ @ support and 6-16mmØ @ midspan Main Bars (Grade 40);
10mmØ 2 leg-stirrups: Sp. at 2@50, 10@70 and rest 200 O.C
 REINFORCED CONCRETE BEAM
B-4
Input Parameters :
Sup Mid
Standard Specs Moment Capacity Top Bot Shear Capacity
fc' = 21 Mpa Tension Bar, Dt = 2 2 bw = 200 mm fyt = 230
fy = 275 Mpa Tension Bar 2-L, Nb = 0 0 h = 300 mm Av = 2
b₁ = .85 Compression Bar, Dc = 2 2 Sb = 10 mm Stirrups Bar Ø
Es = 200 Gpa Main Bar dia, D = 16 Cc = 40 mm, Clear Covering
Moment, Mu = 16.6 20.4
CONDITION : Val = 0.65+0.25 (Ԑt - Ԑty/0.005 - Ԑty) S
Ø = 0.65 , Ԑt ≤ Ԑty 2-16mmØ
Val , Ԑty ˂ Ԑt ˂ 0.005 -- -- --
U
0.90 , Ԑt ≥ 0.005 P
Location of d' & dt; Support Midspan P
As1 = π D² Db /4 = 402.12 402.12 O
2L, As2 = π D² Nb /4 = 0.00 0.00
y = (As 1 y1+As 2 y2)/As = 0.00 0.00 2-16mmØ
R
d' = Cc + Sb + (D/2) + y = 58.00 58.00 T
dt = h - d' = 242.00 242.00
CHECKING : εt ≥ 0.004, Support Midspan
Cma x = 600 d t / fsmin +600 = 103.7 103.71 M
ama x = β1 Cmax = 88.2 88.16 2-16mmØ
I
Asma x = 0.85f'c a max b w / fy = 1144.44 1144.44
a = (As fy- As' fy)/0.85 fc' b = 30.98 30.98 D
C= a/β1 = 36.44 36.44 S
fs' = 600 (C-d')/C = -354.94 -354.94 P
fs' = Compression Bars = Not Yield Not Yield -- -- --
2-16mmØ
A
fs = 600 (dt-C)/C = 3384.38 3384.38
fs = Tension Bars = Yield Yield N
BEAM MOMENT CAPACITY; Ø = 0.9 CHECK SHEAR; Ø = 0.75
As fy = 0.85fc' β1 C bw + As' fs'; Where, fs' = (600 C-d'/C) Vc = 0.17 √fc' bw dt = 38 < 75.00
Support Midspan Vsmax = 0.67 √fc' bw dt = 149 KN
C= by quadratic = 49.76 49.76 Vs = (Vu/Ø ) - Vc = 62.29 < 148.60
a= β1 C = 42.30 42.30 Section is Adequate
fs' = 600 (C-d')/C = -99.31 -99.31 Av = 2 (π Sb²/4)= 157.1
fs = 600 (dt-C)/C = 2317.83 2317.83 Vs ≤ 0.33√f'c bw d, d/2
Max S, w/c
Mn =Cc[d t -(a/2)] + Cs (d t -d')= 26.00 26.00 or 600mm otherwise
ever is
SUPPORT, ØMn = 23.40 > 16.63 Pass!
lesser,mm
Vs > 0.33√f'c bw d,
MIDSPAN, ØMn = 23.40 > 20.42 Pass! d/4 or 300mm

Therefore use 200x300with 4-16mmØ @ support and 4-16mmØ @ midspan Main Bars (Grade 40);
10mmØ 2 leg-stirrups: Sp. at 2@50, 10@60 and rest 200 O.C
 DESIGN OF COLUMNS
REINFORCED CONCRETE COLUMN
C1
Des i gn Pa ra meters :
Ma i n Ba rs Loc -Z As t
h = 400 mm d' = 40 mm fs 1 = 2 - 360.00 402.12
b = 250 mm Ma i n ba rs = 16 mm Ø fs 2 = 2 - 253.33 402.12
fc' = 21 Mpa Mux = 34.366 KNm fs 3 = 0 - 253.33 0
fy = 275 Mpa Pu = 291.657 KN fs 4 = 2 - 146.67 402.12
b₁ = 0.85 Es con = 600 Mpa fs 5 = 2 - 40.00 402.12
Es = 200 Gpa Shea r pa ra meters

Defining Condition; Nvh = 2 , l a tera l ti es l eg

0.65 , Ԑt ≤ Ԑty if fs > fy, use fy Nvb = 4 , l a tera l ti es l eg
Ø = Va l , Ԑty ˂ Ԑt ˂ 0.005 fyt = 230 Mpa , l a tera l ti es
0.90 , Ԑt ≥ 0.005 Ti es , Td = 10 mm Ø
Val = Use 0.65 in transition Region
MAXIMUM AXIAL CAPACITY Ag = 100000 NSCP 422.4.2.2
Pcn = 0.8 [0.85 fc' (Ag-As ) + fy As ] = 1,758.90 kN
Ø = 0.65 , Pcu = Ø Pcn = 1,143.28 kN
BALANCE CONDITION CAPACITY, Ø = 0.65 COMPRESSION CONTROLLED CAPACITY, Ø = .65
Ԑy = fy / Es = 0.00138 Ԑt = -0.002
Cb = Ԑc d/Ԑc + Ԑy = 246.86 mm Ct =Es con d/(Es con-Es Ԑ t) = 216.00 mm
ab = βC = 209.83 mm at = βC = 183.60 mm
from s tra i n di a gra m As [fy or fs ] from s tra i n di a gra m As [fy or fs ]
fs 1 = 600(d-C)/C = 275.00 T1 = 110.58 KN, Tens i on fs 1 = 600(d-C)/C = 400.00 T1 = 110.58 KN, T
fs 2 = 600(C-Z 2 )/C = -15.74 C2 = -6.33 KN, Tens i on fs 2 = 600(C-Z 2 )/C = -103.70 C2 = -41.70 KN, T
fs 3 = 600(C-Z 3 )/C = 0.00 C3 = 0.00 KN, fs 3 = 600(C-Z 3 )/C = 0.00 C3 = 0.00 KN,
fs 4 = 600(C-Z 4 )/C = 243.52 C4 = 97.92 KN, Compres s i on fs 4 = 600(C-Z 4 )/C = 192.59 C4 = 77.45 KN, C
fs 5 = 600(C-Z 5 )/C = 502.78 C5 = 110.58 KN, Compres s i on fs 5 = 600(C-Z 5 )/C = 488.89 C5 = 110.58 KN, C
Cc = .85 f'c a b = 936.36 KN Cc = .85 f'c a b = 819.315 KN
[∑Fv = 0], Pbn =C2+C3+C4+C5+Cc - T = 1028.0 KN [∑Fv = 0], Pbn =C2+C3+C4+C5+Cc - T = 855.1 KN
[∑MT = 0], fi nd e = x-z, z= 160.00 mm [∑MT = 0], fi nd e = x-z, z = 160 mm
PbnX = C 2 X 2 +C 3 X 3 +C 4 X 4 +C 5 X 5 +C c X c PbnX = C 2 X 2 +C 3 X 3 +C 4 X 4 +C 5 X 5 +C c X c
eb = 126.45 mm ØPb = 668.2 KN et = 96.99 mm ØPt = 555.79 KN
Mb = 129.98 KNm ØMb = 84.49 KNm Mt = 53.91 KNm ØMt = 35.04 KNm
ECCENTRICALLY LOADED SECTION CAPACITY, Ø = .65 CHECK SHEAR, Øv = 0.75
due to a ppl i ed l oa d, ex = 117.83 Vc = 0.17[1+(Pu/14Ag)] √fc' b dt = 84.72 79.07 KN
[∑Fv = 0], Pbn =C2 +C3 +C4 +C5 +Cc -T Av = π Td² Nv / 4 = 157.1 314.2 mm²
[∑MT = 0], PbnX =C2X2+C3X3+C4X4+C5X5+CcXc S max, min (16db, 48dties and least col dimension)
C= 255.10 mm a = 216.84 mm 16 db = 256 mm
fs 1 =600(d-C)/C = 246.73 T1 = 99.21 KN, Tens i on 48 dti es = 480 mm
fs 2 =
600(C-Z 2 )/C = 4.16 C2 = 1.67 KN, Compres s i on Lea s t Col umn di mens i on = 250 mm
fs 3 =
600(C-Z 3 )/C = 0.00 C3 = 0.00 KN,
fs 4 =
600(C-Z 4 )/C = 255.04 C4 = 102.56 KN, Compres s i on
fs 5 =
600(C-Z 5 )/C = 505.92 C5 = 110.58 KN, Compres s i on
Cc = .85 f'c a b = 967.63
Pnx = 1083.22 ØPn = 704.09 KN > 291.66 Pa s s !
Mnx = 127.64 ØMn = 82.96 KNm > 34.37 Pa s s !

Therefore use, 400x250mm 8-16mm Ø longitudinal bars (GRADE 40) with 10mm Ø lateral ties space at,
2@50, 10@60mm , and Rest 200mm O.C, BOTH ENDS.
 REINFORCED CONCRETE COLUMN
PC-1
Des i gn Pa ra meters :
Ma i n Ba rs Loc -Z As t
h = 400 mm d' = 40 mm fs 1 = 2 - 360.00 402.12
b = 200 mm Ma i n ba rs = 16 mm Ø fs 2 = 0 - 360.00 0
fc' = 21 Mpa Mux = 19.45 KNm fs 3 = 2 - 200.00 402.12
fy = 275 Mpa Pu = 25.166 KN fs 4 = 0 - 200.00 0
b₁ = 0.85 Es con = 600 Mpa fs 5 = 2 - 40.00 402.12
Es = 200 Gpa Shea r pa ra meters

Defining Condition; Nvh = 2 , l a tera l ti es l eg

0.65 , Ԑt ≤ Ԑty if fs > fy, use fy Nvb = 3 , l a tera l ti es l eg
Ø = Va l , Ԑty ˂ Ԑt ˂ 0.005 fyt = 230 Mpa , l a tera l ti es
0.90 , Ԑt ≥ 0.005 Ti es , Td = 10 mm Ø
Val = Use 0.65 in transition Region
MAXIMUM AXIAL CAPACITY Ag = 80000 NSCP 422.4.2.2
Pcn = 0.8 [0.85 fc' (Ag-As ) + fy As ] = 1,390.57 kN
Ø = 0.65 , Pcu = Ø Pcn = 903.87 kN
BALANCE CONDITION CAPACITY, Ø = 0.65 TENSION CONTROLLED CAPACITY, Ø = .90
Ԑy = fy / Es = 0.00138 Ԑt = -0.005
Cb = Ԑc d/Ԑc + Ԑy = 246.86 mm Ct =Es con d/(Es con-Es Ԑ t) = 135.00 mm
ab = βC = 209.83 mm at = β C = 114.75 mm
from s tra i n di a gra m As [fy or fs ] from s tra i n di a gra m As [fy or fs ]
fs 1 = 600(d-C)/C = 275.00 T1 = 110.58 KN, Tens i on fs 1 = 600(d-C)/C = 1000.00 T1 = 110.58 KN, T
fs 2 = 600(C-Z 2 )/C = 0.00 C2 = 0.00 KN, fs 2 = 600(C-Z 2 )/C = 0.00 C2 = 0.00 KN,
fs 3 = 600(C-Z 3 )/C = 113.89 C3 = 45.80 KN, Compres s i on fs 3 = 600(C-Z 3 )/C = -288.89 C3 = -110.58 KN, T
fs 4 = 600(C-Z 4 )/C = 0.00 C4 = 0.00 KN, fs 4 = 600(C-Z 4 )/C = 0.00 C4 = 0.00 KN,
fs 5 = 600(C-Z 5 )/C = 502.78 C5 = 110.58 KN, Compres s i on fs 5 = 600(C-Z 5 )/C = 422.22 C5 = 110.58 KN, C
Cc = .85 f'c a b = 749.088 KN Cc = .85 f'c a b = 409.658 KN
[∑Fv = 0], Pbn =C2+C3+C4+C5+Cc - T = 794.9 KN [∑Fv = 0], Pbn =C2+C3+C4+C5+Cc - T = 299.1 KN
[∑MT = 0], fi nd e = x-z, z= 160.00 mm [∑MT = 0], fi nd e = x-z, z = 160 mm
PbnX = C 2 X 2 +C 3 X 3 +C 4 X 4 +C 5 X 5 +C c X c PbnX = C 2 X 2 +C 3 X 3 +C 4 X 4 +C 5 X 5 +C c X c
eb = 134.13 mm ØPb = 516.7 KN et = 254.52 mm ØPt = 269.17 KN
Mb = 106.61 KNm ØMb = 69.30 KNm Mt = 68.51 KNm ØMt = 61.66 KNm
ECCENTRICALLY LOADED SECTION CAPACITY, Ø = .90 CHECK SHEAR, Øv = 0.75
due to a ppl i ed l oa d, ex = 772.87 Vc = 0.17[1+(Pu/14Ag)] √fc' b dt = 57.35 50.98 KN
[∑Fv = 0], Pbn =C2 +C3 +C4 +C5 +Cc -T Av = π Td² Nv / 4 = 157.1 235.6 mm²
[∑MT = 0], PbnX =C2X2+C3X3+C4X4+C5X5+CcXc S max, min (16db, 48dties and least col dimension)
C= 69.16 mm a= 58.79 mm 16 db = 256 mm
fs 1 = 600(d-C)/C = 2523.19 T1 = 110.58 KN, Tens i on 48 dti es = 480 mm
fs 2 = 600(C-Z 2 )/C = 0.00 C2 = 0.00 KN, Lea s t Col umn di mens i on = 200 mm
fs 3 = 600(C-Z 3 )/C = -1135.11 C3 = 110.58 KN, Tens i on
fs 4 = 600(C-Z 4 )/C = 0.00 C4 = 0.00 KN,
fs 5 = 600(C-Z 5 )/C = 252.98 C5 = 101.73 KN, Compres s i on
Cc = .85 f'c a b = 209.87
Pnx = 90.43 ØPn = 81.38 KN > 25.17 Pa s s !
Mnx = 69.89 ØMn = 62.90 KNm > 19.45 Pa s s !

Therefore use, 400x200mm 6-16mm Ø longitudinal bars (GRADE 40) with 10mm Ø lateral ties space at,
2@50, 10@50mm , and Rest 200mm O.C, BOTH ENDS.
 DESIGN OF FOOTING TIE BEAM
REINFORCED CONCRETE BEAM
FTB-1
Input Parameters :
Sup Mid
Standard Specs Moment Capacity Top Bot Shear Capacity
fc' = 21 Mpa Tension Bar, Dt = 2 2 bw = 200 mm fyt = 230
fy = 275 Mpa Tension Bar 2-L, Nb = 2 2 h = 400 mm Av = 2
b₁ = .85 Compression Bar, Dc = 2 2 Sb = 10 mm Stirrups Bar Ø
Es = 200 Gpa Main Bar dia, D = 16 Cc = 40 mm, Clear Covering
Moment, Mu = 55.1 45.6
CONDITION : Val = 0.65+0.25 (Ԑt - Ԑty/0.005 - Ԑty)
S
Ø = 0.65 , Ԑt ≤ Ԑty 2-16mmØ
Val , Ԑty ˂ Ԑt ˂ 0.005 2-16mmØ U
0.90 , Ԑt ≥ 0.005 P
Location of d' & dt; Support Midspan P
As1 = π D² Db /4 = 402.12 402.12 O
2L, As2 = π D² Nb /4 = 402.12 402.12
R
y = (As1 y1+As2 y2)/As = 30.00 30.00 2-16mmØ
d' = Cc + Sb + (D/2) + y = 88.00 88.00
T
dt = h - d' = 312.00 312.00
CHECKING : εt ≥ 0.004, Support Midspan
Cmax = 600 d t / fsmin +600 = 133.7 133.71
M
amax = β1 Cmax = 113.7 113.66 2-16mmØ
Asmax = 0.85f'c a max b w / fy = 1475.48 1475.48 I
a =(As fy- As' fy)/0.85 fc' b = 61.95 61.95 D
C= a/β1 = 72.88 72.88 S
fs' = 600 (C-d')/C = -124.43 -124.43 P
fs' = Compression Bars = Not Yield Not Yield 2-16mmØ
A
fs = 600 (dt-C)/C = 1968.45 1968.45 2-16mmØ
fs = Tension Bars = Yield Yield
N
BEAM MOMENT CAPACITY; Ø = 0.9 CHECK SHEAR; Ø = 0.75
As fy =0.85fc' β1 C bw + As' fs'; Where, fs' = (600 C-d'/C) Vc = 0.17 √fc' bw dt = 49 < 75.00
Support Midspan Vsmax = 0.67 √fc' bw dt = 192 KN
C= by quadratic = 80.40 80.40 Vs = (Vu/Ø ) - Vc = 51.39 < 191.59
a= β1 C = 68.34 68.34 Section is Adequate
fs' = 600 (C-d')/C = -56.68 -56.68 Av = 2 (π Sb²/4)= 157.1
fs = 600 (dt-C)/C = 1728.24 1728.24 Vs ≤ 0.33√f'c bw d, d/2
Max S, w/c
Mn =Cc[d t -(a/2)] + Cs (d t -d')= 62.68 62.68 or 600mm otherwise
ever is
SUPPORT, ØMn = 56.41 > 55.12 Pass! Vs > 0.33√f'c bw d,
lesser,mm
MIDSPAN, ØMn = 56.41 > 45.59 Pass! d/4 or 300mm

Therefore use 200x400with 6-16mmØ @ support and 6-16mmØ @ midspan Main Bars (Grade 40);
10mmØ 2 leg-stirrups: Sp. at 2@50, 10@70 and rest 150 O.C
 DESIGN OF ISOLATED FOOTINGS
PROJECT NAME : CONCEPCION RESIDENCE PREPARED BY : FSL
SUBJECT : F1

Lx P
P
NGL NGL

dsoil dsoil
Lz h Vx Vz
X-AXIS
b t
t

Z-AXIS
qsoil qsoil
PLAN VIEW SECTION ALONG X-AXIS SECTION ALONG Z-AXIS
`
PARAMETERS :
FOOTING SIZE COLUMN SIZE
Length Lx = 1.80 m Length h = 400 mm
Width Lz = 1.80 m Width b = 250 mm
Thickness t = 350 mm

SOIL PROPERTIES : MATERIAL STRENGTH :

Soil Bearing capacity : qall = 144.00 kPa ( Gross ) Concrete Strength f'c = 21.0 MPa
Soil Overburden Depth dsoil = 1.50 m Reinf. Steel Yield Strength fy = 276.0 MPa
Soil Unit Weight g soil = 18.1 kN/m 3
Water Table dw = 0.0 m

PRIMARY LOADS :
Axial, P Axial, T Mom, MX Mom, MZ Shear, V x Shear, V z
LOAD TYPE
( kN ) ( kN ) (kN-m) (kN-m) (kN) (kN)
Dead 228.41 - 0.00 0.00 2.64 4.94
Live 48.14 - 0.00 0.00 0.64 0.31
P
Roof Live 0.00 - 0.00 0.00 0.00 0.00 Vx
Vz X-AXIS
Seismic, EQX 25.63 25.33 0.00 0.00 27.74 2.18
Seismic, EQZ 7.43 7.14 0.00 0.00 4.15 23.24
Z-AXIS
Wind, WX 1.26 1.26 0.00 0.00 11.52 0.14
Wind, WZ 4.27 4.27 0.00 0.00 1.46 13.76
Surcharge, Ws 2 kPa kPa Note : Mx & Mz are Moments are due to column eccentricity

Footing Wt. = g conc ( Lx ) ( Lz ) ( t ) Surcharge = Ws ( Lx ) ( Lz )

= 26.69 kN = 7.78 kN
Soil Overrburden = g soil ( Lx ) ( Lz ) ( d soil )
= 87.97 kN

LOAD COMBINATION FACTORS ( SERVICE )

LOAD COMB
D L RL EQX EQZ WX WZ
CASE
LC1 1.00 1.00 1.00 -D + L + RL
LC2 1.00 1.00 0.71 -D + L + EQx/1.40
LC3 1.00 1.00 0.71 -D + L + EQz/1.40
LC4 1.00 0.75 0.75 0.54 -D + 0.75L + 0.75RL + 0.75EQx/1.40
LC5 1.00 0.75 0.75 0.54 -D + 0.75L + 0.75RL + 0.75EQz/1.40
LC6 0.60 0.71 -D + EQx/1.40
LC7 0.60 0.71 -D + EQz/1.40
LC8 1.00 0.75 0.75 0.45 -D + 0.75L + 0.75RL + 0.75(0.60Wx)
LC9 1.00 0.75 0.75 0.45 -D + 0.75L + 0.75RL + 0.75(0.60Wz)
LC10 1.00 1.00 0.60 -D + L + 0.60Wx
LC11 1.00 1.00 0.60 -D + L + 0.60Wz
LC12 0.60 0.60 -0.60D + 0.60Wx
LC13 0.60 0.60 -0.60D + 0.60Wz
 LOAD COMBINATION FACTORS ( STRENGTH )
LOAD COMB
D L RL EQX EQZ WX WZ
CASE
LC1 1.40 -1.40D
LC2 1.20 0.50 1.60 -1.20D + 0.50L + 1.60RL
LC3 1.20 1.60 0.50 -1.20D + 1.60L + 0.50RL
LC3 1.00 0.50 1.00 -1.20D + 0.50RL + 1.0EQx
LC4 1.00 0.50 1.00 -1.20D + 0.50RL + 1.0EQz
LC5 0.90 1.00 -0.90D + 1.0EQx
LC6 0.90 1.00 -0.90D + 1.0EQz
LC7 1.20 1.60 0.50 -1.20D + 1.60RL + 0.50Wx
LC8 1.20 1.60 0.50 -1.20D + 1.60RL + 0.50Wz
LC9 1.20 0.50 0.50 1.00 -1.20D + 0.50L + 0.50RL + 1.0Wx
LC10 1.20 0.50 0.50 1.00 -1.20D + 0.50L + 0.50RL + 1.0Wz
LC11 0.90 1.00 -0.90D + 1.0Wx
LC12 0.90 1.00 -0.90D + 1.0Wz

BEARING PRESSURE CHECK

P
COMBINATIONS_WITH DEAD AND LIVE -D + L + RL
Forces :
P = 398.98 kN mx = Lx/2 - ex = - mm dsoil
Mx = 0.00 kN-m ex = 0.00 mm < Lx / 6 Vx
Mz = 0.00 kN-m mz = Lz/2 - ez = - mm
Ix = 0.875 m
4
ez = 0.00 mm < Lx / 6
t
Iz = 0.875 m4
Soil Pressure : qs
qs = P/A + Mx (c) / Ix + Mz (c) / Iz = 123.14 kPa < qallow ( OK!!! )

COMBINATIONS_WITH SEISMIC LOAD -D + L + EQx/1.40

Forces :
P = 417.29 kN mx = Lx/2 - ex = - mm
Mx = 0.00 kN-m ex = 0.00 mm < Lx / 6
Mz = 0.00 kN-m mz = Lz/2 - ez = - mm
Ix = 0.875 m4 ez = 0.00 mm < Lx / 6
Iz = 0.875 m4
Soil Pressure :
qs = P/A + Mx c / Ix + Mz c / Iz = 128.79 kPa < qallow ( OK!!! )

COMBINATIONS_WITH WIND LOAD -D + L + 0.60Wz

Forces :
P = 401.54 kN mx = Lx/2 - ex = - mm
Mx = 0.00 kN-m ex = 0.00 mm < Lx / 6
Mz = 0.00 kN-m mz = Lz/2 - ez = - mm
Ix = 0.875 m4 ez = 0.00 mm < Lx / 6
Iz = 0.875 m4
Soil Pressure :
qs = P/A + Mx c / Ix + Mz c / Iz = 123.93 kPa < qallow ( OK!!! )

OVERTURNING CHECK
p
OVERTURNNG & RESISTING MOMENTS X-DIR Z-DIR X
OVERTURNING MOMENTS, OM Seismic,EQ
Seismic ( M / 1.40 ) OMEQ = 0.00 0.00 kN-m Wind, W
OM
Wind ( M / 1.60 ) OMW = 0.00 0.00 kN-m
RIGHTING MOMENTS, RM
Footing Weight RM1 = 24.02 24.02 kN-m
Deadload RM2 = 205.57 205.57 kN-m RM
Soil Overburden RM3 = 79.17 79.17 kN-m
Total Righting Moment RMTOT = 308.76 308.76 kN-m
R = RMTOT / OMTOT = --- ---
---- ----
REMARKS
---- ----
SLIDING CHECK
Soil Unit Weight gs oi l = 18.1 kN/m
3
Coeff. of Friction m = 0.30
Angle of Int. Friction f = 30.0 deg.
ka = (1 - sinf )/( 1 + sinf) = 0.333 ( Active Pressure Coefficient )
kp = 1 / ka = 3.00 ( Passive Pressure Coefficient )
WTOT
WTOT = 343.07 kN ( W DEAD + W SOIL + W FTG )
PPAS1 = 1/2 [ kp g L(ds )2 ] Seismic,EQ
= 24.44 kN ( Soil Passive pressure @ Pedestal_Along X-dir )
= 15.27 kN ( Soil Passive pressure @ Pedestal_Along Z-dir ) Wind, W
PPAS2 = 1/2[ kp g (ds + (ds + t)] ( L ) ( t )
NGL
= 57.30 kN ( Soil Passive pressure @ Footing_Along X-dir ) PPAS1
= 57.30 kN ( Soil Passive pressure @ Footing_Along X-dir ) PPAS2
FRESIST = 184.65 kN (P PAS1 +P PAS2 +W TOT x m )_Along X-dir
175.49 kN (P PAS1 +P PAS2 +W TOT x m )_Along Z-dir
FSLIDING = 19.41 kN ( Max 0.60F W or 0.707F E _Serviceability_Along X-dir ) WTOT ( m )
16.27 kN ( Max 0.60F W or 0.707F E _Serviceability_Along Z-dir )
Ratio, FRESIST/FSLIDING
RSL @ X-dir = FRESIST/FSLIDING = 9.51 > 1.50 ( OK!!! )
RSL @ Z-dir = FRESIST/FSLIDING = 10.79 > 1.50 ( OK!!! )

UPLIFT CHECK
Total Resisting Force, P down
Pdown = 343.07 kN ( W DEAD + W SOIL + W FTG )
Uplift Force, P up
Pup = Pwa ter + ( Max. of TEQ / 1.40 or TW/1.60 )
= 18.09 kN

Ratio, P DOWN/PUP
RUP = PDOWN/PUP = 18.97 > 1.50 ( OK!!! )

FLEXURE AND SHEAR DESIGN

A. FLEXURE DESIGN

ALONG LENGTH, Lx P
qux = P/A
= 153.714 kPa m = ---- mm
d = t - cc - fBOT /2 X = Lx
= 267.0 mm = 1.80 m Mux
Muma x = qux(Lz)(Lx/2-b/2)^2/2
t
= 83.09 kN-m y = ---- kPa
> r min ( Pressure @ Support Face )
r = 2.662E-03 qumax
< r max
X
Use r : 0.0027
Using : 16 bar
No. Of Bars : 7.0 pcs ( Minimum Required) Along X - Dir.
ALONG LENGTH, Lz

P
quZ = P/A
= 153.714 kPa m = ---- mm
d = t - cc - fBOT1 - fBOT 2/2 X = Lz
= 251.0 mm = 1.80 m Muz
Muma x = qux(Lx)(Lz/2-h/2)^2/2
= 67.79 kN-m y = ---- kPa t
> r min ( Pressure @ Support Face )
r = 2.453E-03 qumax
< r max
Use r : 0.0025 X
Using : 16 bar
No. Of Bars : 7.0 pcs ( Minimum Required) Along Z - Dir.
B. SHEAR DESIGN
LINE OF SHEAR
(PUNCHING
Punching Shear Force, Vp u
Lx
Vpu = Maximum P u -1.20D + 1.60L + 0.50RL
= 351.11 kN (for Vn 1 to Vn 3 _Punching Shear)

One-way Shear Force, Vu yx = 0.00 kPa

Vux = qux (Lz) [(Lx-b)/2-d] yz = ---- kPa
Lz
= 140.56 kN ( for Vn 4 _One-way Shear )
Vuz = quz (Lx) [(Lz-h)/2-d]
= 124.23

LINE OF SHEAR
Punching Shear Capacity (ONE-WAY)

( 1 + (2)/ b )/6 f'c

0.50
Vn1 = bo d = 1086.51 kN
( a s d/b o + 2 )/12 f'c
0.50
Vn2 = bo d = 1571.85 kN
Vn3 = f'c
0.50
bo d/3 = 965.79 kN
PLAN
where:
b = 1.6 as = 40
bo = 2368.00 mm

Vn = Smaller of ( Vn 1 , Vn 2 , Vn 3 ) = 965.79 kN
LINE OF SHEAR
fVn = 0.75 ( Vn ) = 724.34 kN > Vpu ( OK!!! ) (ONE-WAY)

t
One-way Shear Capacity
0.50
Vn4 = f'c bw d/6 = 367.06 kN
qsoil
LINE OF SHEAR…
fVn = 0.75 ( Vn4 ) = 275.30 kN > Vu ( OK!!! )

SECTION
PROJECT NAME : CONCEPCION RESIDENCE PREPARED BY : FSL
SUBJECT : F2

P P
Lx NGL
NGL

dsoil dsoil
Vx Vz
Lz h
X-AXIS
b t t

Z-AXIS qsoil
qsoil
PLAN VIEW SECTION ALONG X-AXIS SECTION ALONG Z-AXIS
`
PARAMETERS :
FOOTING SIZE COLUMN SIZE
Length Lx = 1.50 m Length h = 400 mm
Width Lz = 1.50 m Width b = 250 mm
Thickness t = 300 mm

SOIL PROPERTIES : MATERIAL STRENGTH :

Soil Bearing capacity : qall = 144.00 kPa ( Gross ) Concrete Strength f'c = 21.0 MPa
Soil Overburden Depth dsoil = 1.50 m Reinf. Steel Yield Strength fy = 276.0 MPa
Soil Unit Weight g soil = 18.1 kN/m 3
Water Table dw = 0.0 m

PRIMARY LOADS :
Axial, P Axial, T Mom, MX Mom, MZ Shear, V x Shear, Vz
LOAD TYPE
( kN ) ( kN ) (kN-m) (kN-m) (kN) (kN)
Dead 158.31 - 0.00 0.00 0.08 6.36
Live 18.13 - 0.00 0.00 0.00 0.52
P
Roof Live 0.00 - 0.00 0.00 0.00 0.00 Vx
Vz X-AXIS
Seismic, EQX 14.43 12.25 0.00 0.00 36.06 2.86
Seismic, EQZ 18.84 16.93 0.00 0.00 2.98 15.32
Z-AXIS
Wind, WX 1.26 1.26 0.00 0.00 11.52 0.14
Wind, WZ 4.27 4.27 0.00 0.00 1.46 13.76
Surcharge, Ws 2 kPa kPa Note : Mx & Mz are Moments are due to column eccentricity

Footing Wt. = g conc ( Lx ) ( Lz ) ( t ) Surcharge = Ws ( Lx ) ( Lz )

= 15.89 kN = 5.40 kN
Soil Overrburden = g soil ( Lx ) ( Lz ) ( d soil )
= 61.09 kN

LOAD COMBINATION FACTORS ( SERVICE )

LOAD COMB
D L RL EQX EQZ WX WZ
CASE
LC1 1.00 1.00 1.00 -D + L + RL
LC2 1.00 1.00 0.71 -D + L + EQx/1.40
LC3 1.00 1.00 0.71 -D + L + EQz/1.40
LC4 1.00 0.75 0.75 0.54 -D + 0.75L + 0.75RL + 0.75EQx/1.40
LC5 1.00 0.75 0.75 0.54 -D + 0.75L + 0.75RL + 0.75EQz/1.40
LC6 0.60 0.71 -D + EQx/1.40
LC7 0.60 0.71 -D + EQz/1.40
LC8 1.00 0.75 0.75 0.45 -D + 0.75L + 0.75RL + 0.75(0.60Wx)
LC9 1.00 0.75 0.75 0.45 -D + 0.75L + 0.75RL + 0.75(0.60Wz)
LC10 1.00 1.00 0.60 -D + L + 0.60Wx
LC11 1.00 1.00 0.60 -D + L + 0.60Wz
LC12 0.60 0.60 -0.60D + 0.60Wx
LC13 0.60 0.60 -0.60D + 0.60Wz
 LOAD COMBINATION FACTORS ( STRENGTH )
LOAD COMB
D L RL EQX EQZ WX WZ
CASE
LC1 1.40 -1.40D
LC2 1.20 0.50 1.60 -1.20D + 0.50L + 1.60RL
LC3 1.20 1.60 0.50 -1.20D + 1.60L + 0.50RL
LC3 1.00 0.50 1.00 -1.20D + 0.50RL + 1.0EQx
LC4 1.00 0.50 1.00 -1.20D + 0.50RL + 1.0EQz
LC5 0.90 1.00 -0.90D + 1.0EQx
LC6 0.90 1.00 -0.90D + 1.0EQz
LC7 1.20 1.60 0.50 -1.20D + 1.60RL + 0.50Wx
LC8 1.20 1.60 0.50 -1.20D + 1.60RL + 0.50Wz
LC9 1.20 0.50 0.50 1.00 -1.20D + 0.50L + 0.50RL + 1.0Wx
LC10 1.20 0.50 0.50 1.00 -1.20D + 0.50L + 0.50RL + 1.0Wz
LC11 0.90 1.00 -0.90D + 1.0Wx
LC12 0.90 1.00 -0.90D + 1.0Wz

BEARING PRESSURE CHECK P

COMBINATIONS_WITH DEAD AND LIVE -D + L + RL

Forces :
P = 258.81 kN mx = Lx/2 - ex = - mm
dsoil
Vx
Mx = 0.00 kN-m ex = 0.00 mm < Lx / 6
Mz = 0.00 kN-m mz = Lz/2 - ez = - mm t
4
Ix = 0.422 m ez = 0.00 mm < Lx / 6
Iz = 0.422 m4
qs
Soil Pressure :
qs = P/A + Mx (c) / Ix + Mz (c) / Iz = 115.03 kPa < qallow ( OK!!! )

COMBINATIONS_WITH SEISMIC LOAD -D + L + EQz/1.40

Forces :
P = 272.27 kN mx = Lx/2 - ex = - mm
Mx = 0.00 kN-m ex = 0.00 mm < Lx / 6
Mz = 0.00 kN-m mz = Lz/2 - ez = - mm
Ix = 0.422 m4 ez = 0.00 mm < Lx / 6
Iz = 0.422 m4
Soil Pressure :
qs = P/A + Mx c / Ix + Mz c / Iz = 121.01 kPa < qallow ( OK!!! )

COMBINATIONS_WITH WIND LOAD -D + L + 0.60Wz

Forces :
P = 261.37 kN mx = Lx/2 - ex = - mm
Mx = 0.00 kN-m ex = 0.00 mm < Lx / 6
Mz = 0.00 kN-m mz = Lz/2 - ez = - mm
Ix = 0.422 m4 ez = 0.00 mm < Lx / 6
Iz = 0.422 m4
Soil Pressure :
qs = P/A + Mx c / Ix + Mz c / Iz = 116.17 kPa < qallow ( OK!!! )

OVERTURNING CHECK
p
OVERTURNNG & RESISTING MOMENTS X-DIR Z-DIR X
OVERTURNING MOMENTS, OM Seismic,EQ
Seismic ( M / 1.40 ) OMEQ = 0.00 0.00 kN-m Wind, W
OM
Wind ( M / 1.60 ) OMW = 0.00 0.00 kN-m
RIGHTING MOMENTS, RM
Footing Weight RM1 = 11.92 11.92 kN-m
Deadload RM2 = 118.73 118.73 kN-m RM
Soil Overburden RM3 = 45.82 45.82 kN-m
Total Righting Moment RMTOT = 176.46 176.46 kN-m
R = RMTOT / OMTOT = --- ---
---- ----
REMARKS
---- ----
SLIDING CHECK
Soil Unit Weight gs oi l = 18.1 kN/m 3 Coeff. of Friction m = 0.30
Angle of Int. Friction f = 30.0 deg.
ka = (1 - sinf )/( 1 + sinf) = 0.333 ( Active Pressure Coefficient )
kp = 1 / ka = 3.00 ( Passive Pressure Coefficient )
WTOT
WTOT = 235.29 kN ( W DEAD + W SOIL + W FTG )
PPAS1 = 1/2 [ kp g L(ds )2 ] Seismic,EQ
= 24.44 kN ( Soil Passive pressure @ Pedestal_Along X-dir )
= 15.27 kN ( Soil Passive pressure @ Pedestal_Along Z-dir ) Wind, W
PPAS2 = 1/2[ kp g (ds + (ds + t)] ( L ) ( t )
NGL
= 40.32 kN ( Soil Passive pressure @ Footing_Along X-dir ) PPAS1
= 40.32 kN ( Soil Passive pressure @ Footing_Along X-dir ) PPAS2
FRESIST = 135.34 kN (P PAS1 +P PAS2 +W TOT x m )_Along X-dir
126.18 kN (P PAS1 +P PAS2 +W TOT x m )_Along Z-dir
FSLIDING = 25.24 kN ( Max 0.60F W or 0.707F E _Serviceability_Along X-dir ) WTOT ( m )
10.73 kN ( Max 0.60F W or 0.707F E _Serviceability_Along Z-dir )
Ratio, FRESIST/FSLIDING
RSL @ X-dir = FRESIST/FSLIDING = 5.36 > 1.50 ( OK!!! )
RSL @ Z-dir = FRESIST/FSLIDING = 11.76 > 1.50 ( OK!!! )

UPLIFT CHECK
Total Resisting Force, P down
Pdown = 235.29 kN ( W DEAD + W SOIL + W FTG )
Uplift Force, P up
Pup = Pwa ter + ( Max. of TEQ / 1.40 or TW/1.60 )
= 12.09 kN

Ratio, P DOWN/PUP
RUP = PDOWN/PUP = 19.46 > 1.50 ( OK!!! )

FLEXURE AND SHEAR DESIGN

A. FLEXURE DESIGN

ALONG LENGTH, Lx P
qux = P/A
= 149.760 kPa m = ---- mm
d = t - cc - fBOT /2 X = Lx
= 217.0 mm = 1.50 m Mux
Muma x = qux(Lz)(Lx/2-b/2)^2/2
= 43.88 kN-m y = ---- kPa t
> r min ( Pressure @ Support Face )
r = 2.551E-03
< r max
qumax
Use r : 0.0026
Using : 16 bar X
No. Of Bars : 6.0 pcs ( Minimum Required) Along X - Dir.
ALONG LENGTH, Lz
P
quZ = P/A
= 149.760 kPa m = ---- mm
d = t - cc - fBOT1 - fBOT 2/2 X = Lz
= 201.0 mm = 1.50 m
Muz
Muma x = qux(Lx)(Lz/2-h/2)^2/2
= 33.98 kN-m y = ---- kPa
> r min ( Pressure @ Support Face )
t
r = 2.298E-03
< r max
Use r : 0.0023 qumax
Using : 16 bar X
No. Of Bars : 6.0 pcs ( Minimum Required) Along Z - Dir.
B. SHEAR DESIGN
LINE OF SHEAR
(PUNCHING
Punching Shear Force, Vp u Lx
Vpu = Maximum P u -1.40D
= 221.63 kN (for Vn 1 to Vn 3 _Punching Shear)

One-way Shear Force, Vu yx = 0.00 kPa

Vux = qux (Lz) [(Lx-b)/2-d] yz = ---- kPa
= 91.65 kN ( for Vn 4 _One-way Shear ) Lz
Vuz = quz (Lx) [(Lz-h)/2-d]
= 78.40

Punching Shear Capacity LINE OF SHEAR

(ONE-WAY)

Vn1 = ( 1 + (2)/ b )/6 f'c 0.50 bo d = 808.46 kN

Vn2 = ( a s d/b o + 2 )/12 f'c 0.50 bo d = 1078.61 kN
Vn3 = f'c
0.50
bo d/3 = 718.63 kN
PLAN
where:
b = 1.6 as = 40
bo = 2168.00 mm

Vn = Smaller of ( Vn 1 , Vn 2 , Vn 3 ) = 718.63 kN

LINE OF SHEAR
fVn = 0.75 ( Vn ) = 538.98 kN > Vpu ( OK!!! ) (ONE-WAY)

t
One-way Shear Capacity
0.50
Vn4 = f'c bw d/6 = 248.60 kN
qsoil
LINE OF SHEAR…
fVn = 0.75 ( Vn4 ) = 186.45 kN > Vu ( OK!!! )

SECTION