UNIT-2

Highway Alignment and Engineering Survey (4 hrs)

2.1 Highway Alignment
2.1.1 Jntroduction
2.1.2 Requirements ofHighway Alignment
2.1.3 Factors Controlling Highway Alignment
2.2 Engineering Survey for highway alignment
2.2.1Engineering Survey: Map Study, Reconnaissance, Preliminary and Detailed Survey

2.1.1 Introduction:

The position of the center line of the highway in the ground is called highway alignment. Highway
alignment includes horizontal alignment and vertical alignment. The projection of highway
alignment in horizontal plane is called horizontal alignment and the projection in vertical plane is
known as vertical alignment. Alignment must be selected in such a way that the overall cost during
construction, operation and maintenance is minimum. Road design outputs are in the form of
following drawings:

2.1.2 Requirements of Highway Alignment:

The ideal alignment must have the following requirements:

• Safe (S)
• Easy (E)
• Short (S)
• Economical (E)
• Comfort (C)
The requirements can be memorized as SESEC.

Safe: The alignment need to be safe during construction, operation and maintenance especially at
slopes, embankments and cutting.

Easy: The construction materials if present at the place of construction makes the construction
easier. Similarly, it should be easy during the operation of vehicles with easy gradients and curves.

Short: The distance between the initial and final point ne e d to be short so as to re duce the
construction cost.
Economical: The alignment should be economical during construction, operation, and maintenance. However, if
the construction turned out to be economical, the gradient may not be easy which in turns increases the cost of
operation and maintenance. Similarly, if the vehicle operation is taken under consideration and is made
economical, the construction cost becomes higher as the gradient and curves need to be easy.
Comfort: The alignment should be fixed such that it provides comfort to the drivers and the passengers.

Highway Alignment and Engineering Survey Er. Rakesh Pandit

 2

2.1.3 Factors Controlling Highway Alignment:

a) Governmental Requirement: As the road project needs a large investment,

the government should be clear about the requirement of the road (when, what, how and
why to construct).

b) Obligatory Poi nts: Obligatory points determine the highway alignment. They are
further divided into positive obligatory points and negative obligatory
points.
i) Posi ti ve Obligatory Poi nts: These are those points through which the alignment
should pass.

• Existing Road: The alignment should be fixed such that the newly constructed road
should link to the existing road. It reduces the cost of construction.
• Intermediate Town: If there is the possibility of C
a straight road between point A and B and there
lies the intermediate town at C as shown, then the
road need to link the intermediate town reducing A . B

the change in highway alignment. ·

• Bridge site/Existing Bridge: The road linking with the bridge '
li
__·__ --·•:
'
_
I

must not be curved and to include the bridge in the road portion, [ · __
�____ .-- · 1
the highway alignment may be changed. .
---____,,--
• Mountain: When the road has to cross a row of hills, mountain pass may be the suitable
alternative.

i i ) Negati ve Obligatory Poi nts: These are those points through which the alignment
should not pass.

• Valleys, ponds, and marshy land need to be avoided.

• Religious places are linked up with the human sentiment so cannot be destroyed for
fixing the road alignment.
• Costly structures present in the way of alignment should be considered and the road
alignment should be fixed such that it won't destroy those costly structures as the value
of compensation for such structures will be more.
• Conservation areas and restricted zones.
• Densely populated area.
• The road should not be within the boundary of the country.

Highway Alignm ent and Engmeenng Survey Er. Rakesh Pandit

 3

c) Traffic (Type, amount and flow pattern):

The alignment should be according to the traffic amount and flow pattern. The number of
lanes can be determined as:
Number oflanes = Traffic Volume/ Traffic Capacity.
d) Geological Condition:
Geologically stable hill slope must be considered while selecting the highway alignment.
e) Geometric Design:
Various factors regarding geometric design as the radius ofcurve, sight distance, gradient
determines the highway alignment.
f) Availability of construction materials and labor:
The construction works become easier and economical when the construction materials are near
the place ofhighway alignment.
f) Economy:
The construction, operation, and maintenance work should be economical. So, highway
alignment is selected keeping these things in mind.

g)Other Considerations:
Drainage: The alignment needs to be fixed such that the number of cross drainage
structures are less.
Political: Alignment need to be within the allocated territory.
Monotony: Setting the straight alignment leads to monotonous driving. So a small bend is
provided to make the driver aware and alert. The roads are designed as forgiving roads.

Special Consideration in Hill Roads:

• Stability: The road should be aligned with the hill side that is stable. Excessive cutting and
filling may effect on their stability.
• Drainage: Adequate drainage facility need to be provided across the road and the number
ofcross drainage structures need to be less during construction.
• Geometric Standards: Geometric design parameters also effect on the construction of
roads. Minimizing steep gradient, hairpin bends and needless rise and fall.
• Resisting Length: The ineffective rise and excessive fall should be minimum.

2.2 Engineering Survey for highway alignment:

• Map Study
• Reconnaissance
• Preliminary Survey
• Detailed Survey

Highway Alignment and Engineering Survey Er. Rakesh Pandit

 4

a) Map Study:
The study of the topographical map is done to find out the possible routes of the road.
Following information are obtained from the map study:
• Alignment avoiding valley, ponds, lakes.
• When the road has to cross a row of hills, mountain pass may be the suitable alternative.
• Approximate location of the bridge site.

b) Reconnaissance Survey:
Simple Survey Instruments are used in the reconnaissance procedure.
Following are the information obtained from the reconnaissance survey:

• Valley, pond, lakes and other features that were not present in the topographical map.
• A number of cross drainage structures, High Flood Level (HFL), Natural Ground Level.
• Values of the gradient, the length of gradients and radius of the circular curve.
• Soil type along the routes from field identification tests and observation of the geological
features.
• Sources of construction materials.

c) Preliminary Survey:
Sophisticated Survey Instruments are used during the preliminary survey.
Objective of the Preliminary Survey are listed below:
• To collect necessary physical information and details of topography, drainage, and soil.
• To compare different proposal in view of the requirement of good alignment.
• To estimate the quantity of earthwork.
• To finalize the best alignment.

Methods of Preliminary Survey:

• Conventional Approach
• Modem Rapid Approach

Conventional Method:
The procedure for the conventional approach are listed below:
• Traverse: The traverse is run from the starting point to the end point by setting out various
control points. Both primary traverse and secondary traverse may need to be run.
• Levelling work: The levelling work is carried out along the centre line or the proposed
road. The levelling work is used to estimate the volume of the earthwork. Both L-section
and X-section are carried out.
• Topographical features: All geographical and man-made features are survey and plotted
which are along the traverse and for a certain width on either side.

Highway Alignment and Engineering Survey Er. Rakesh Pandit

 5

• Drainage Studies and Hydrological data: The number of cross drainage structures are
estimated during the preliminary survey.
• Soil Survey: The soil survey is conducted in working out details of earthwork, slope, and
stability of materials, subsoil and surface drainage requirements and the type of the
pavement requirements.
• Material Survey: The location of construction materials need to be known.
• Traffic Survey: Survey regarding the number of lanes, roadway width, and pavement
design need to be done.
• Determination of final centre line: After completion of all the above mention steps and
calculating the amount of earthwork, the final centre line is determined.

Modern rapid approach:

The procedure of the Modem rapid approach are listed below as:
• Taking aerial photographs with required lateral and longitudinal overlaps.
• These photographs are then examined under stereoscopes and control points are selected
for the establishment of the traverse.
• The spot levels and contour lines may be obtained from the stereo - pair observations.
• Photointerpretation method is used to grab information on the geological features, soil
conditions, drainage requirement, etc.

d) Final location and Detailed Survey:

Final Location:
The alignment finalized at the design office after preliminary survey is to be first
located on the field by establishing the center line. Details survey should be carried out
for collecting the information necessary for the preparation of plans and construction
details for the highway project location.
Details survey:
• Temporary Bench Marks (TBM) are fixed at all under pass structures and drainage
structures.
• Levels along the final centre line should be taken with great importance as these data are
required for vertical alignment, earth work calculation, and drainage details.
• A detailed survey is carried out to enable drawing the soil profile up to the depth of 1.5-
3m below the Ground Line and twice the height of the finished embankment in the case of
the high embankment.
• The data during the detailed survey should be elaborated and completed for the preparation
of the plans, designing, and estimation of the project.

Highway Alignment and Engineering Survey Er. Rakesh Pandit