nRF52840

Product Specification
v1.9

4413_417 v1.9 / 2024-02-15

Feature list
Features:
®
• Bluetooth 5, IEEE 802.15.4-2006, 2.4 GHz transceiver • Flexible power management

• -95 dBm sensitivity in 1 Mbps Bluetooth low energy mode • 1.7 V to 5.5 V supply voltage range

• -103 dBm sensitivity in 125 kbps Bluetooth low energy mode (long range) • On-chip DC/DC and LDO regulators with automated low

• -20 to +8 dBm TX power, configurable in 4 dB steps current modes

• On-air compatible with nRF52, nRF51, nRF24L, and nRF24AP Series devices • 1.8 V to 3.3 V regulated supply for external components

• Supported data rates: • Automated peripheral power management

• Fast wake-up using 64 MHz internal oscillator

• Bluetooth 5 – 2 Mbps, 1 Mbps, 500 kbps, and 125 kbps
• 0.4 µA at 3 V in System OFF mode, no RAM retention
• IEEE 802.15.4-2006 – 250 kbps
• 1.5 µA at 3 V in System ON mode, no RAM retention, wake on
• Proprietary 2.4 GHz – 2 Mbps, 1 Mbps
RTC
• Single-ended antenna output (on-chip balun)
• 1 MB flash and 256 kB RAM
• 128-bit AES/ECB/CCM/AAR co-processor (on-the-fly packet encryption)
• Advanced on-chip interfaces
• 4.8 mA peak current in TX (0 dBm)

• 4.6 mA peak current in RX • USB 2.0 full speed (12 Mbps) controller

• RSSI (1 dB resolution) • QSPI 32 MHz interface

•
® ®
Arm Cortex -M4 32-bit processor with FPU, 64 MHz • High-speed 32 MHz SPI

® • Type 2 near field communication (NFC-A) tag with wake-on

• 212 EEMBC CoreMark score running from flash memory
field
• 52 µA/MHz running CoreMark from flash memory
• Touch-to-pair support
• Watchpoint and trace debug modules (DWT, ETM, and ITM)
• Programmable peripheral interconnect (PPI)
• Serial wire debug (SWD)
• 48 general purpose I/O pins
• Rich set of security features
® ™ • EasyDMA automated data transfer between memory and
• Arm TrustZone CryptoCell 310 security subsystem
peripherals
• NIST SP800-90A and SP800-90B compliant random number generator • Nordic SoftDevice ready with support for concurrent multiprotocol
• AES-128 – ECB, CBC, CMAC/CBC-MAC, CTR, CCM/CCM* • 12-bit, 200 ksps ADC – 8 configurable channels with
• Chacha20/Poly1305 AEAD supporting 128- and 256-bit key size programmable gain
• SHA-1 and SHA-2 up to 256 bit • 64 level comparator
• Keyed-hash message authentication code (HMAC) • 15 level low-power comparator with wake-up from System OFF
• RSA up to 2048-bit key size mode

• SRP up to 3072-bit key size • Temperature sensor

• ECC support for most used curves, including P-256 (secp256r1) and • Four 4 channel pulse width modulator (PWM) units with EasyDMA
Ed25519/Curve25519 • Audio peripherals – I2S, digital microphone interface (PDM)
• Application key management using derived key model • Five 32-bit timers with counter mode
• Secure boot ready • Up to four SPI masters/three SPI slaves with EasyDMA

• Flash access control list (ACL) • Up to two I2C compatible two-wire master/slave

• Root-of-trust (RoT) • Two UART (CTS/RTS) with EasyDMA

• Debug control and configuration • Quadrature decoder (QDEC)

• Access port protection (CTRL-AP) • Three real-time counters (RTC)

• Secure erase • Single crystal operation

• Package variants
™
• aQFN73 package, 7 x 7 mm

• QFN48 package, 6 x 6 mm

• WLCSP package, 3.544 x 3.607 mm

4413_417 v1.9 ii
 Feature list

Applications:
• Advanced computer peripherals and I/O devices • Internet of things (IoT)

• Mouse • Smart home sensors and controllers

• Keyboard • Industrial IoT sensors and controllers

• Multi-touch trackpad • Interactive entertainment devices

• Advanced wearable devices • Remote controls

• Health/fitness sensors and monitoring devices • Gaming controllers

• Wireless payment enabled devices

4413_417 v1.9 iii

Contents
Feature list. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

1 Revision history. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2 About this document. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

2.1 Document status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.2 Peripheral chapters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.2.1 Peripheral naming conventions. . . . . . . . . . . . . . . . . . . . . . . . . 16
2.3 Register tables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.3.1 Fields and values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.3.2 Permissions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.4 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.4.1 DUMMY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

3 Block diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

4 Core components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
4.1 CPU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
4.1.1 Floating point interrupt. . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
4.1.2 CPU and support module configuration. . . . . . . . . . . . . . . . . . . . . 20
4.1.3 Electrical specification. . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4.2 Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4.2.1 RAM - Random access memory. . . . . . . . . . . . . . . . . . . . . . . . 22
4.2.2 Flash - Non-volatile memory. . . . . . . . . . . . . . . . . . . . . . . . . . 22
4.2.3 Memory map. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
4.2.4 Instantiation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.3 NVMC — Non-volatile memory controller. . . . . . . . . . . . . . . . . . . . . . 25
4.3.1 Writing to flash. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4.3.2 Erasing a page in flash. . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
4.3.3 Writing to user information configuration registers (UICR). . . . . . . . . . . . . . 26
4.3.4 Erasing user information configuration registers (UICR). . . . . . . . . . . . . . . 26
4.3.5 Erase all. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
4.3.6 Access port protection behavior. . . . . . . . . . . . . . . . . . . . . . . . 26
4.3.7 Partial erase of a page in flash. . . . . . . . . . . . . . . . . . . . . . . . . 27
4.3.8 Cache. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
4.3.9 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
4.3.10 Electrical specification. . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
4.4 FICR — Factory information configuration registers. . . . . . . . . . . . . . . . . . 32
4.4.1 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
4.5 UICR — User information configuration registers. . . . . . . . . . . . . . . . . . . 46
4.5.1 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
4.6 EasyDMA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
4.6.1 EasyDMA error handling. . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
4.6.2 EasyDMA array list. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
4.7 AHB multilayer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
4.8 Debug and trace. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
4.8.1 DAP - Debug access port. . . . . . . . . . . . . . . . . . . . . . . . . . . 67
4.8.2 Access port protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
4.8.3 CTRL-AP - Control access port. . . . . . . . . . . . . . . . . . . . . . . . . 70
4.8.4 Debug Interface mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

4413_417 v1.9 iv
 4.8.5 Real-time debug. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
4.8.6 Trace. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

5 Power and clock management. . . . . . . . . . . . . . . . . . . . . . . . 74

5.1 Power management unit (PMU). . . . . . . . . . . . . . . . . . . . . . . . . . 74
5.2 Current consumption. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
5.2.1 Electrical specification. . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
5.3 POWER — Power supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
5.3.1 Main supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
5.3.2 USB supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
5.3.3 System OFF mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
5.3.4 System ON mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
5.3.5 RAM power control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
5.3.6 Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
5.3.7 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
5.3.8 Electrical specification. . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
5.4 CLOCK — Clock control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
5.4.1 HFCLK controller. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
5.4.2 LFCLK controller. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
5.4.3 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
5.4.4 Electrical specification. . . . . . . . . . . . . . . . . . . . . . . . . . . . 169

6 Peripherals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
6.1 Peripheral interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
6.1.1 Peripheral ID. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
6.1.2 Peripherals with shared ID. . . . . . . . . . . . . . . . . . . . . . . . . . 173
6.1.3 Peripheral registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
6.1.4 Bit set and clear. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
6.1.5 Tasks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
6.1.6 Events. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
6.1.7 Shortcuts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
6.1.8 Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
6.2 AAR — Accelerated address resolver. . . . . . . . . . . . . . . . . . . . . . . . 175
6.2.1 EasyDMA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
6.2.2 Resolving a resolvable address. . . . . . . . . . . . . . . . . . . . . . . . 175
6.2.3 Example. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
6.2.4 IRK data structure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
6.2.5 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
6.2.6 Electrical specification. . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
6.3 ACL — Access control lists. . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
6.3.1 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
6.4 CCM — AES CCM mode encryption. . . . . . . . . . . . . . . . . . . . . . . . 191
6.4.1 Keystream generation. . . . . . . . . . . . . . . . . . . . . . . . . . . . 192
6.4.2 Encryption. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192
6.4.3 Decryption. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193
6.4.4 AES CCM and RADIO concurrent operation. . . . . . . . . . . . . . . . . . . 194
6.4.5 Encrypting packets on-the-fly in radio transmit mode. . . . . . . . . . . . . . . 194
6.4.6 Decrypting packets on-the-fly in RADIO receive mode. . . . . . . . . . . . . . . 195
6.4.7 CCM data structure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
6.4.8 EasyDMA and ERROR event. . . . . . . . . . . . . . . . . . . . . . . . . . 197
6.4.9 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197
6.4.10 Electrical specification. . . . . . . . . . . . . . . . . . . . . . . . . . . 204
6.5 COMP — Comparator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204

4413_417 v1.9 v
 6.5.1 Differential mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206
6.5.2 Single-ended mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207
6.5.3 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208
6.5.4 Electrical specification. . . . . . . . . . . . . . . . . . . . . . . . . . . . 215
6.6 CRYPTOCELL — Arm TrustZone CryptoCell 310. . . . . . . . . . . . . . . . . . . . 216
6.6.1 Usage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
6.6.2 Always-on (AO) power domain. . . . . . . . . . . . . . . . . . . . . . . . 217
6.6.3 Life cycle state (LCS). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
6.6.4 Cryptographic key selection. . . . . . . . . . . . . . . . . . . . . . . . . . 218
6.6.5 Direct memory access (DMA). . . . . . . . . . . . . . . . . . . . . . . . . 218
6.6.6 Standards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219
6.6.7 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220
6.6.8 Host interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220
6.7 ECB — AES electronic codebook mode encryption. . . . . . . . . . . . . . . . . . 223
6.7.1 Shared resources. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223
6.7.2 EasyDMA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224
6.7.3 ECB data structure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224
6.7.4 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224
6.7.5 Electrical specification. . . . . . . . . . . . . . . . . . . . . . . . . . . . 227
6.8 EGU — Event generator unit. . . . . . . . . . . . . . . . . . . . . . . . . . . 227
6.8.1 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227
6.8.2 Electrical specification. . . . . . . . . . . . . . . . . . . . . . . . . . . . 240
6.9 GPIO — General purpose input/output. . . . . . . . . . . . . . . . . . . . . . . 240
6.9.1 Pin configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241
6.9.2 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243
6.9.3 Electrical specification. . . . . . . . . . . . . . . . . . . . . . . . . . . . 289
6.10 GPIOTE — GPIO tasks and events. . . . . . . . . . . . . . . . . . . . . . . . 290
6.10.1 Pin events and tasks. . . . . . . . . . . . . . . . . . . . . . . . . . . . 290
6.10.2 Port event. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291
6.10.3 Tasks and events pin configuration. . . . . . . . . . . . . . . . . . . . . . 291
6.10.4 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 292
6.11 I2S — Inter-IC sound interface. . . . . . . . . . . . . . . . . . . . . . . . . . 310
6.11.1 Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 310
6.11.2 Transmitting and receiving. . . . . . . . . . . . . . . . . . . . . . . . . . 310
6.11.3 Left right clock (LRCK). . . . . . . . . . . . . . . . . . . . . . . . . . . 311
6.11.4 Serial clock (SCK). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 311
6.11.5 Master clock (MCK). . . . . . . . . . . . . . . . . . . . . . . . . . . . 312
6.11.6 Width, alignment and format. . . . . . . . . . . . . . . . . . . . . . . . 313
6.11.7 EasyDMA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 314
6.11.8 Module operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 316
6.11.9 Pin configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 318
6.11.10 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319
6.11.11 Electrical specification. . . . . . . . . . . . . . . . . . . . . . . . . . . 328
6.12 LPCOMP — Low-power comparator. . . . . . . . . . . . . . . . . . . . . . . 329
6.12.1 Shared resources. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 330
6.12.2 Pin configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 330
6.12.3 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 331
6.12.4 Electrical specification. . . . . . . . . . . . . . . . . . . . . . . . . . . 337
6.13 MWU — Memory watch unit. . . . . . . . . . . . . . . . . . . . . . . . . . 337
6.13.1 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 338
6.14 NFCT — Near field communication tag. . . . . . . . . . . . . . . . . . . . . . 370
6.14.1 Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 371
6.14.2 Operating states. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 373
6.14.3 Pin configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 374

4413_417 v1.9 vi
 6.14.4 EasyDMA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 374
6.14.5 Frame assembler. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375
6.14.6 Frame disassembler. . . . . . . . . . . . . . . . . . . . . . . . . . . . 376
6.14.7 Frame timing controller. . . . . . . . . . . . . . . . . . . . . . . . . . . 377
6.14.8 Collision resolution. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 378
6.14.9 Antenna interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 379
6.14.10 NFCT antenna recommendations. . . . . . . . . . . . . . . . . . . . . . 379
6.14.11 Battery protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . 380
6.14.12 References. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 380
6.14.13 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 380
6.14.14 Electrical specification. . . . . . . . . . . . . . . . . . . . . . . . . . . 398
6.15 PDM — Pulse density modulation interface. . . . . . . . . . . . . . . . . . . . 399
6.15.1 Master clock generator. . . . . . . . . . . . . . . . . . . . . . . . . . . 400
6.15.2 Module operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400
6.15.3 Decimation filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400
6.15.4 EasyDMA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400
6.15.5 Hardware example. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 401
6.15.6 Pin configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 402
6.15.7 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 403
6.15.8 Electrical specification. . . . . . . . . . . . . . . . . . . . . . . . . . . 409
6.16 PPI — Programmable peripheral interconnect. . . . . . . . . . . . . . . . . . . 410
6.16.1 Pre-programmed channels. . . . . . . . . . . . . . . . . . . . . . . . . . 411
6.16.2 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 412
6.17 PWM — Pulse width modulation. . . . . . . . . . . . . . . . . . . . . . . . . 460
6.17.1 Wave counter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 461
6.17.2 Decoder with EasyDMA. . . . . . . . . . . . . . . . . . . . . . . . . . . 464
6.17.3 Limitations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 471
6.17.4 Pin configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 471
6.17.5 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 472
6.18 QDEC — Quadrature decoder. . . . . . . . . . . . . . . . . . . . . . . . . . 484
6.18.1 Sampling and decoding. . . . . . . . . . . . . . . . . . . . . . . . . . . 485
6.18.2 LED output. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 485
6.18.3 Debounce filters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 486
6.18.4 Accumulators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 486
6.18.5 Output/input pins. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 487
6.18.6 Pin configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 487
6.18.7 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 487
6.18.8 Electrical specification. . . . . . . . . . . . . . . . . . . . . . . . . . . 498
6.19 QSPI — Quad serial peripheral interface. . . . . . . . . . . . . . . . . . . . . . 498
6.19.1 Configuring peripheral. . . . . . . . . . . . . . . . . . . . . . . . . . . 498
6.19.2 Write operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 499
6.19.3 Read operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 499
6.19.4 Erase operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 499
6.19.5 Execute in place. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 499
6.19.6 Sending custom instructions. . . . . . . . . . . . . . . . . . . . . . . . . 500
6.19.7 Deep power-down mode. . . . . . . . . . . . . . . . . . . . . . . . . . 501
6.19.8 Instruction set. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 501
6.19.9 Interface description. . . . . . . . . . . . . . . . . . . . . . . . . . . . 501
6.19.10 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 506
6.19.11 Electrical specification. . . . . . . . . . . . . . . . . . . . . . . . . . . 518
6.20 RADIO — 2.4 GHz radio. . . . . . . . . . . . . . . . . . . . . . . . . . . . 518
6.20.1 Packet configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . 519
6.20.2 Address configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . 520
6.20.3 Data whitening. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 521

4413_417 v1.9 vii

 6.20.4 CRC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 521
6.20.5 Radio states. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 522
6.20.6 Transmit sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 522
6.20.7 Receive sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 524
6.20.8 Received signal strength indicator (RSSI). . . . . . . . . . . . . . . . . . . . 525
6.20.9 Interframe spacing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 525
6.20.10 Device address match. . . . . . . . . . . . . . . . . . . . . . . . . . . 526
6.20.11 Bit counter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 527
6.20.12 IEEE 802.15.4 operation. . . . . . . . . . . . . . . . . . . . . . . . . . 527
6.20.13 EasyDMA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 535
6.20.14 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 536
6.20.15 Electrical specification. . . . . . . . . . . . . . . . . . . . . . . . . . . 569
6.21 RNG — Random number generator. . . . . . . . . . . . . . . . . . . . . . . . 575
6.21.1 Bias correction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 576
6.21.2 Speed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 576
6.21.3 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 576
6.21.4 Electrical specification. . . . . . . . . . . . . . . . . . . . . . . . . . . 578
6.22 RTC — Real-time counter. . . . . . . . . . . . . . . . . . . . . . . . . . . . 578
6.22.1 Clock source. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 579
6.22.2 Resolution versus overflow and the PRESCALER. . . . . . . . . . . . . . . . . 579
6.22.3 COUNTER register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 580
6.22.4 Overflow features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 580
6.22.5 TICK event. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 580
6.22.6 Event control feature. . . . . . . . . . . . . . . . . . . . . . . . . . . . 581
6.22.7 Compare feature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 581
6.22.8 TASK and EVENT jitter/delay. . . . . . . . . . . . . . . . . . . . . . . . . 583
6.22.9 Reading the COUNTER register. . . . . . . . . . . . . . . . . . . . . . . . 585
6.22.10 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 586
6.23 SAADC — Successive approximation analog-to-digital converter. . . . . . . . . . . . 594
6.23.1 Channel and input configuration. . . . . . . . . . . . . . . . . . . . . . . 594
6.23.2 Operation modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 596
6.23.3 Digital output. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 598
6.23.4 EasyDMA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 598
6.23.5 Event monitoring using limits. . . . . . . . . . . . . . . . . . . . . . . . 599
6.23.6 Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 600
6.23.7 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 600
6.23.8 Electrical specification. . . . . . . . . . . . . . . . . . . . . . . . . . . 633
6.24 SPI — Serial peripheral interface master. . . . . . . . . . . . . . . . . . . . . . 634
6.24.1 Functional description. . . . . . . . . . . . . . . . . . . . . . . . . . . 634
6.24.2 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 637
6.24.3 Electrical specification. . . . . . . . . . . . . . . . . . . . . . . . . . . 641
6.25 SPIM — Serial peripheral interface master with EasyDMA. . . . . . . . . . . . . . 642
6.25.1 SPI master transaction sequence. . . . . . . . . . . . . . . . . . . . . . . 643
6.25.2 D/CX functionality. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 644
6.25.3 Pin configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 645
6.25.4 EasyDMA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 645
6.25.5 Low power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 646
6.25.6 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 646
6.25.7 Electrical specification. . . . . . . . . . . . . . . . . . . . . . . . . . . 658
6.26 SPIS — Serial peripheral interface slave with EasyDMA. . . . . . . . . . . . . . . . 659
6.26.1 Shared resources. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 659
6.26.2 EasyDMA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 660
6.26.3 SPI slave operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 660
6.26.4 Pin configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 662

4413_417 v1.9 viii

 6.26.5 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 663
6.26.6 Electrical specification. . . . . . . . . . . . . . . . . . . . . . . . . . . 671
6.27 SWI — Software interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . 673
6.27.1 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 673
6.28 TEMP — Temperature sensor. . . . . . . . . . . . . . . . . . . . . . . . . . 673
6.28.1 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 673
6.28.2 Electrical specification. . . . . . . . . . . . . . . . . . . . . . . . . . . 679
6.29 TWI — I2C compatible two-wire interface. . . . . . . . . . . . . . . . . . . . . 680
6.29.1 Functional description. . . . . . . . . . . . . . . . . . . . . . . . . . . 680
6.29.2 Master mode pin configuration. . . . . . . . . . . . . . . . . . . . . . . . 680
6.29.3 Shared resources. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 681
6.29.4 Master write sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . 681
6.29.5 Master read sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . 682
6.29.6 Master repeated start sequence. . . . . . . . . . . . . . . . . . . . . . . 683
6.29.7 Low power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 684
6.29.8 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 684
6.29.9 Electrical specification. . . . . . . . . . . . . . . . . . . . . . . . . . . 692
6.30 TIMER — Timer/counter. . . . . . . . . . . . . . . . . . . . . . . . . . . . 692
6.30.1 Capture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 694
6.30.2 Compare. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 694
6.30.3 Task delays. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 694
6.30.4 Task priority. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 694
6.30.5 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 694
6.31 TWIM — I2C compatible two-wire interface master with EasyDMA. . . . . . . . . . . 704
6.31.1 EasyDMA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 706
6.31.2 Master write sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . 706
6.31.3 Master read sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . 707
6.31.4 Master repeated start sequence. . . . . . . . . . . . . . . . . . . . . . . 708
6.31.5 Low power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 709
6.31.6 Master mode pin configuration. . . . . . . . . . . . . . . . . . . . . . . . 709
6.31.7 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 709
6.31.8 Electrical specification. . . . . . . . . . . . . . . . . . . . . . . . . . . 720
6.31.9 Pullup resistor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 721
6.32 TWIS — I2C compatible two-wire interface slave with EasyDMA. . . . . . . . . . . . 721
6.32.1 EasyDMA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 723
6.32.2 TWI slave responding to a read command. . . . . . . . . . . . . . . . . . . 723
6.32.3 TWI slave responding to a write command. . . . . . . . . . . . . . . . . . . 725
6.32.4 Master repeated start sequence. . . . . . . . . . . . . . . . . . . . . . . 726
6.32.5 Terminating an ongoing TWI transaction. . . . . . . . . . . . . . . . . . . . 726
6.32.6 Low power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 727
6.32.7 Slave mode pin configuration. . . . . . . . . . . . . . . . . . . . . . . . 727
6.32.8 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 727
6.32.9 Electrical specification. . . . . . . . . . . . . . . . . . . . . . . . . . . 738
6.33 UART — Universal asynchronous receiver/transmitter. . . . . . . . . . . . . . . . 738
6.33.1 Functional description. . . . . . . . . . . . . . . . . . . . . . . . . . . 738
6.33.2 Pin configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 739
6.33.3 Shared resources. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 739
6.33.4 Transmission. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 739
6.33.5 Reception. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 740
6.33.6 Suspending the UART. . . . . . . . . . . . . . . . . . . . . . . . . . . . 741
6.33.7 Error conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 741
6.33.8 Using the UART without flow control. . . . . . . . . . . . . . . . . . . . . 741
6.33.9 Parity and stop bit configuration. . . . . . . . . . . . . . . . . . . . . . . 741
6.33.10 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 741

4413_417 v1.9 ix
 6.33.11 Electrical specification. . . . . . . . . . . . . . . . . . . . . . . . . . . 750
6.34 UARTE — Universal asynchronous receiver/transmitter with EasyDMA. . . . . . . . . 750
6.34.1 EasyDMA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 751
6.34.2 Transmission. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 751
6.34.3 Reception. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 752
6.34.4 Error conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 754
6.34.5 Using the UARTE without flow control. . . . . . . . . . . . . . . . . . . . . 754
6.34.6 Parity and stop bit configuration. . . . . . . . . . . . . . . . . . . . . . . 754
6.34.7 Low power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 754
6.34.8 Pin configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 755
6.34.9 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 755
6.34.10 Electrical specification. . . . . . . . . . . . . . . . . . . . . . . . . . . 768
6.35 USBD — Universal serial bus device. . . . . . . . . . . . . . . . . . . . . . . 768
6.35.1 USB device states. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 769
6.35.2 USB terminology. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 770
6.35.3 USB pins. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 771
6.35.4 USBD power-up sequence. . . . . . . . . . . . . . . . . . . . . . . . . . 771
6.35.5 USB pull-up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 772
6.35.6 USB reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 772
6.35.7 USB suspend and resume. . . . . . . . . . . . . . . . . . . . . . . . . . 773
6.35.8 EasyDMA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 774
6.35.9 Control transfers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 775
6.35.10 Bulk and interrupt transactions. . . . . . . . . . . . . . . . . . . . . . . 778
6.35.11 Isochronous transactions. . . . . . . . . . . . . . . . . . . . . . . . . . 780
6.35.12 USB register access limitations. . . . . . . . . . . . . . . . . . . . . . . 783
6.35.13 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 783
6.35.14 Electrical specification. . . . . . . . . . . . . . . . . . . . . . . . . . . 837
6.36 WDT — Watchdog timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . 837
6.36.1 Reload criteria. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 838
6.36.2 Temporarily pausing the watchdog. . . . . . . . . . . . . . . . . . . . . . 838
6.36.3 Watchdog reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 838
6.36.4 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 838
6.36.5 Electrical specification. . . . . . . . . . . . . . . . . . . . . . . . . . . 844

7 Hardware and layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 845

7.1 Pin assignments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 845
7.1.1 aQFN73 ball assignments. . . . . . . . . . . . . . . . . . . . . . . . . . . 845
7.1.2 QFN48 pin assignments. . . . . . . . . . . . . . . . . . . . . . . . . . . 848
7.1.3 WLCSP ball assignments. . . . . . . . . . . . . . . . . . . . . . . . . . . 850
7.2 Mechanical specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . 854
7.2.1 aQFN73 7 x 7 mm package. . . . . . . . . . . . . . . . . . . . . . . . . . 854
7.2.2 QFN48 6 x 6 mm package. . . . . . . . . . . . . . . . . . . . . . . . . . 855
7.2.3 WLCSP 3.544 x 3.607 mm package. . . . . . . . . . . . . . . . . . . . . . . 856
7.3 Reference circuitry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 856
7.3.1 Circuit configuration no. 1 for QIAA aQFN73. . . . . . . . . . . . . . . . . . . 858
7.3.2 Circuit configuration no. 2 for QIAA aQFN73. . . . . . . . . . . . . . . . . . . 860
7.3.3 Circuit configuration no. 3 for QIAA aQFN73. . . . . . . . . . . . . . . . . . . 862
7.3.4 Circuit configuration no. 4 for QIAA aQFN73. . . . . . . . . . . . . . . . . . . 864
7.3.5 Circuit configuration no. 5 for QIAA aQFN73. . . . . . . . . . . . . . . . . . . 866
7.3.6 Circuit configuration no. 6 for QIAA aQFN73. . . . . . . . . . . . . . . . . . . 868
7.3.7 Circuit configuration no. 7 for QIAA aQFN73. . . . . . . . . . . . . . . . . . . 870
7.3.8 Circuit configuration no. 1 for QFAA QFN48. . . . . . . . . . . . . . . . . . . 872
7.3.9 Circuit configuration no. 1 for CKAA WLCSP. . . . . . . . . . . . . . . . . . . 874
7.3.10 Circuit configuration no. 2 for CKAA WLCSP. . . . . . . . . . . . . . . . . . . 876

4413_417 v1.9 x
 7.3.11 Circuit configuration no. 3 for CKAA WLCSP. . . . . . . . . . . . . . . . . . . 878
7.3.12 Circuit configuration no. 4 for CKAA WLCSP. . . . . . . . . . . . . . . . . . . 880
7.3.13 Circuit configuration no. 5 for CKAA WLCSP. . . . . . . . . . . . . . . . . . . 882
7.3.14 Circuit configuration no. 6 for CKAA WLCSP. . . . . . . . . . . . . . . . . . . 884
7.3.15 PCB guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 886
7.3.16 PCB layout example. . . . . . . . . . . . . . . . . . . . . . . . . . . . 887
7.3.17 PMIC support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 888
7.4 Package thermal characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . 889
7.5 Package Variation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 889
7.5.1 QFN48. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 889

8 Recommended operating conditions. . . . . . . . . . . . . . . . . . . . 890

8.1 WLCSP light sensitivity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 890

9 Absolute maximum ratings. . . . . . . . . . . . . . . . . . . . . . . . . 891

10 Ordering information. . . . . . . . . . . . . . . . . . . . . . . . . . . . 893

10.1 Device marking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 893
10.2 Box labels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 893
10.3 Order code. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 894
10.4 Code ranges and values. . . . . . . . . . . . . . . . . . . . . . . . . . . . 895
10.5 Product options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 896

11 Legal notices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 898

4413_417 v1.9 xi
1 Revision history
Date Version Description
February 2024 1.9 The following content has been added or updated:
• Added content in the following chapters:
• Pin assignments – Recommended usage for pin
P0.18 as QSPI CSN for WLCSP package
• RADIO – Parameters PACP,R, IEEE 802.15.4 and PACP,A, IEEE
802.15.4
• SAADC – Sections Shared Resources, and Operation
Modes
• SPI, TWI, and UART – RXD register description
• Updated content in the following chapters:
• FICR – INFO.VARIANTS and INFO.PART
• NVMC – Removed deprecated registers ERASEPCR1
and ERASEPCR0
• Ordering information – MOQ for the nRF52840-
QFAA-F-R7 device
• PWM – Example and images in Wave Counter
section
• SAADC – Removed tACQ parameters
• SPIS – Electrical parameters tSPIS,VSO, tSPIS,HSO,
tSPIS,SUSI, and tSPIS,HSI. Removed deprecated registers
• About this document – Permissions table
• Reference circuitry – Circuit configuration no. 1 for
QFAA QFN48 package
• Editorial changes

December 2023 1.8 The following content has been added:

• Reference circuitry – PMIC support section

November 2021 1.7 The following content has been added or updated:
• Absolute maximum ratings – Updated aQFN73 ESD
CDM maximum value according to PCN162

November 2021 1.6 The following content has been added or updated:
• Ordering information – Build codes Dxx not
recommended for new designs
• Editorial changes

September 2021 1.5 The following content has been added or updated:
• Mechanical specifications – Updated aQFN73
mechanical specification according to PCN148

June 2021 1.4 The following content has been added or updated:

4413_417 v1.9 12
 Revision history

Date Version Description

• Added information for the QFN48 package variant in
• Absolute maximum ratings
• FICR
• Ordering information
• Package variation
• Reference circuitry
• Mechanical specifications
• Pin assignments
• POWER
• Package thermal characteristics – Added QFN48 and
WLCSP thermal resistance and updated aQFN73 with
JEDEC PCB numbers

April 2021 1.3 The following content has been added or updated:
• UICR – Added value HwDisabled to APPROTECT register.
• Debug and trace – Added description of APPROTECT
functionality for devices where APPROTECT is
controlled by hardware and software. Added peripheral
APPROTECT with necessary registers to control
APPROTECT for devices where APPROTECT is controlled
by hardware and software.
• GPIO – Added missing NFC parameters CPAD_NFC and
INFC_LEAK.
• Pin assignments – Added note that DEC5 is not
connected for aQFN73, and WLCSP build codes Fxx and
later.
• Mechanical specifications – Corrected min/max values
of WLCSP D and E dimensions.
• Reference circuitry – Updated aQFN73 and WLCSP
reference circuitry with note on DEC5.
• Ordering information – Updated box labels. Added new
product options.

January 2021 1.2 The following content has been added or updated:
• Updated minimum valid value for EasyDMA MAXCNT
and AMOUNT registers in SPIM, SPIS, TWIM, TWIS, and
UARTE.
• FICR – Added nRF52820 value to INFO.PART register.
Added size of packages to package description. Updated
INFO.VARIANT device variants. Removed reset value
for register TRNG90B.STARTUP and all TEMP module
calibration registers.
• UICR – Updated reference to the VEXTDIF parameter in
the REGOUT0 register.
• NVMC – Updated reset value of register READYNEXT.
Updated registers ERASEPAGE, ERASEALL, ERASEUICR,
ERASEPARTIAL, IHIT, and IMISS.
• POWER – Added Wake from System OFF reset source
for the WDT. Added parameter RSOURCE,VBUSVDDH.

4413_417 v1.9 13
 Revision history

Date Version Description

Renamed parameters to clarify REG0 in the Electrical
Specification. Updated value of parameter RSOURCE,VBUS
to 6 Ω.
• CLOCK – Added parameter VAMP,IN,XO,LOW.
• Current consumption – Added USBD current
measurements. Updated values in Electrical
Specification - Sleep.
• ACL – Added clarification for the maximum protected
region size being limited to half the flash.
• LPCOMP – Added clarification about not disabling
LPCOMP in the same write as COMP is enabled.
• QSPI – Added clarification about XIP region being read
only.
• RADIO – Added EVENTS_SYNC.
• SPIS – Updated parameter tSPIS,HCSN.
• SPIM – Updated parameter tSPIM,CSK.
• TWIM – Updated tTWIM,HD_STA parameter. Clarified use
of SUSPEND and RESUME tasks.
• USBD – Updated the ENABLE register functionality
description. Moved current measurements from the
electrical specification section to CURRENT.
• Mechanical specifications – Added tolerances for D and
E dimensions for WLCSP and aQFN73 packages.
• Reference circuitry – Corrected links. Corrected tables
in WLCSP package Configurations 1 to 6. Added a new
reference design with 4 component RF-match for the
QIAA aQFN73 package. Updated recommended value
for USB serial resistor.
• Package thermal characteristics – Added aQFN73
thermal resistance.
• Ordering information – Corrected WLCSP ball count.
• Absolute maximum ratings – Added footnote on HTOL
supply. Increased Flash memory retention to 10 years at
85°C.
• Recommended operating conditions – Added
parameter TJ and WLCSP package light sensitivity
section.
• Editorial changes.

February 2019 1.1 The following content has been added or updated:
• Added information for the WLCSP package variant in
Pin assignments, Mechanical specifications, Reference
circuitry, FICR, Absolute maximum ratings, and Ordering
information.
• Reference circuitry – Updated RF-Match in aQFN73
reference circuitry for all configurations. Added optional
4.7 Ω resistor to USB supply.
• UICR – Removed NRFFW[13] and NRFFW[14] registers.
• CPU on page 20 – Corrected value of parameter
CMFLASH/mA.

4413_417 v1.9 14
 Revision history

Date Version Description

• POWER – Clarified range of voltages in both Normal and
High voltage modes.
• CLOCK – Corrected value of parameter PD_LFXO to a less
restrictive value.
• EasyDMA – Added section about EasyDMA error
handling. Corrected example code in section EasyDMA
array list.
• NVMC – Added note about the necessity to halt
the CPU before issuing NVMC commands from the
debugger.
• ACL – Corrected register access to ReadWriteOnce
(RWO) for some registers.
• I2S – Removed invalid values from register MCKFREQ,
see parameter fMCK. Fixed figure for Memory mapping
for 8-bit stereo.
• SAADC – Corrected description of functionality of
SAMPLE task.
• SPIS – Exposed the LIST register. Corrected SPI modes
table.
• TWIS – Exposed the LIST register.
• UART – Added STOP bit configuration description.
• RADIO – Added equations to convert from HW RSSI
to 802.15.4 range and dBm. Clarified RSSI timing.
Clarified that TX ramp up time is affected by RU field
in MODECNF0. Added IEEE 802.15.4 radio timing
parameters to the electrical specifications. Added
sensitivity parameter for 2 Mbit NRF mode.
• USBD – Pointed that isochronous transfers have to be
finished before the next SOF event, or the result of the
transfer is undefined.
• Legal notices on page 898 – Updated text and image.

March 2018 1.0 First release

4413_417 v1.9 15
2 About this document
This document is organized into chapters that are based on the modules and peripherals available in the
IC.

2.1 Document status

The document status reflects the level of maturity of the document.

Document name Description

Objective Product Specification (OPS) Applies to document versions up to 1.0.
This document contains target specifications for
product development.

Product Specification (PS) Applies to document versions 1.0 and higher.

This document contains final product
specifications. Nordic Semiconductor ASA reserves
the right to make changes at any time without
notice in order to improve design and supply the
best possible product.

Table 1: Defined document names

2.2 Peripheral chapters

The chapters describing peripherals include the following information:
• A detailed functional description of the peripheral.
• The register configuration for the peripheral.
• The electrical specification tables, containing performance data which apply for the operating
conditions described in Recommended operating conditions on page 890.

2.2.1 Peripheral naming conventions

Every peripheral has a unique capitalized name or an abbreviation of its name, e.g. TIMER, used for
identification and reference.
This name is used in chapter headings and references, and it will appear in the Arm Cortex Microcontroller
Software Interface Standard (CMSIS) hardware abstraction layer to identify the peripheral.
The peripheral instance name, which is different from the peripheral name, is constructed using the
peripheral name followed by a numbered postfix, starting with 0, for example, TIMER0. A postfix is
normally only used if a peripheral can be instantiated more than once. The peripheral instance name is
also used in the CMSIS to identify the peripheral instance.

4413_417 v1.9 16
 About this document

2.3 Register tables

Individual registers are described using register tables. These tables are built up of two sections. The first
three colored rows describe the position and size of the different fields in the register. The following rows
describe the fields in more detail.

2.3.1 Fields and values

The Id (Field Id) row specifies the bits that belong to the different fields in the register. If a field has
enumerated values, then every value will be identified with a unique value id in the Value ID column.
A blank space means that the field is reserved and read as undefined, and it also must be written as 0
to secure forward compatibility. If a register is divided into more than one field, a unique field name is
specified for each field in the Field column. The Value ID may be omitted in the single-bit bit fields when
values can be substituted with a Boolean type enumerator range, e.g. true/false, disable(d)/enable(d), on/
off, and so on.
Values are usually provided as decimal or hexadecimal. Hexadecimal values have a 0x prefix, decimal
values have no prefix.
The Value column can be populated in the following ways:
• Individual enumerated values, for example 1, 3, 9.
• Range of values, e.g. [0..4], indicating all values from and including 0 and 4.
• Implicit values. If no values are indicated in the Value column, all bit combinations are supported, or
alternatively the field's translation and limitations are described in the text instead.
If two or more fields are closely related, the Value ID, Value, and Description may be omitted for all but
the first field. Subsequent fields will indicate inheritance with '..'.
A feature marked Deprecated should not be used for new designs.

2.3.2 Permissions
Different fields in a register might have different access permissions enforced by hardware.
The access permission for each register field is documented in the Access column in the following ways:

Access Description Hardware behavior

R Read-only Field can only be read. A write will be ignored.
W Write-only Field can only be written. A read will return an undefined value.
RW Read-write Field can be read and written multiple times.
W1 Write-once Field can only be written once per reset. Any subsequent write will be ignored. A read will return an undefined value.
RW1 Read-write-once Field can be read multiple times, but only written once per reset. Any subsequent write will be ignored.
W0C Write 0 to clear Field can be read multiple times. A zero clears (set to zero) the corresponding bit in the register. Bits set to one are ignored.
W1C Write 1 to clear Field can be read multiple times. A one clears (set to zero) the corresponding bit in the register. Bits set to zero are ignored.
W1S Write 1 to set Field can be read multiple times. A one sets the corresponding bit in the register. Bits set to zero are ignored.
RME Read Modify External When read, a side effect occurs.

Table 2: Register field permission schemes

4413_417 v1.9 17
 About this document

2.4 Registers
Register overview

Register Offset Description

DUMMY 0x514 Example of a register controlling a dummy feature

2.4.1 DUMMY
Address offset: 0x514
Example of a register controlling a dummy feature

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID I H G F E D D D C C C B A A

Reset 0x00050002 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
A RW FIELD0 Example of a read-write field with several enumerated values
Disabled 0 The example feature is disabled
NormalMode 1 The example feature is enabled in normal mode
ExtendedMode 2 The example feature is enabled along with extra functionality
B RW FIELD1 Example of a deprecated read-write field

This field is deprecated.

Disabled 0 The override feature is disabled
Enabled 1 The override feature is enabled
C RW FIELD2 Example of a read-write field with a valid range of values
ValidRange [2..7] Example of allowed values for this field
D RW FIELD3 Example of a read-write field with no restriction on the values
E R FIELD4 Example of a read-only field
F W FIELD5 Example of a write-only field
G RW FIELD6 Example of a write-one-to-clear field
W1C
H RW FIELD7 Example of a write-zero-to-clear field
W0C
I RW FIELD8 Example of a field that causes a side effect when read
RME

4413_417 v1.9 18
3 Block diagram
This block diagram illustrates the overall system. Arrows with white heads indicate signals that share
physical pins with other signals.

nRF52840
P0.0 – P0.31
RAM0 RAM1 RAM2 RAM3 RAM4 RAM5 RAM6 RAM7 RAM8 GPIO
P1.0 – P1.15

slave

slave

slave

slave

slave

slave

slave

slave

slave

slave
TP TPIU

SWCLK
SW-DP
SWDIO

CTRL-AP AHB multilayer

slave

slave
master

slave

slave

slave
AHB-AP ETM I-Cache

CPU AHB TO APB CODE

FICR UICR
BRIDGE
ARM
CORTEX-M4

NVIC SysTick NVMC

RNG
nRESET POWER
RTC [0..2]
TIMER [0..4]
WDT TEMP

PPI ECB
XC1 master EasyDMA
XC2
CLOCK P0.0 – P0.31 CCM
XL1
P1.0 – P1.15
XL2 master EasyDMA

ANT RADIO AAR

master EasyDMA
EasyDMA master
VBUS
D+ USBD CryptoCell
D-
EasyDMA master master DMA

NFC2 SCK
APB0

NFCT
NFC1 SPIM [0..3] MOSI
EasyDMA master MISO
P0.0 – P0.31 master EasyDMA
P1.0 – P1.15 GPIOTE
COMP SCL
TWIS [0..1]
SDA
LPCOMP master EasyDMA

AIN0 – AIN7 SAADC SCL

TWIM [0..1]
SDA
EasyDMA master master EasyDMA
LED IO0
A IO1
QDEC IO2
B QSPI IO3
SCK
OUT0 – OUT3 PWM [0..3] CSN
EasyDMA master master EasyDMA

MCK RTS
LRCK CTS
UARTE [0..1]
SCL I2S TXD
SDOUT RXD
SDIN master EasyDMA
EasyDMA master
CSN
CLK MISO
PDM SPIS [0..2]
DIN MOSI
SCK
EasyDMA master
master EasyDMA

Figure 1: Block diagram

4413_417 v1.9 19
4 Core components

4.1 CPU
The Arm Cortex-M4 processor with floating-point unit (FPU) has a 32-bit instruction set (Thumb®-2
technology) that implements a superset of 16- and 32-bit instructions to maximize code density and
performance.
This processor implements the following features that enable energy-efficient arithmetic and high-
performance signal processing.
• Digital signal processing (DSP) instructions
• Single-cycle multiply and accumulate (MAC) instructions
• Hardware divide
• 8- and 16-bit single instruction multiple data (SIMD) instructions
• Single-precision floating-point unit (FPU)
The Arm Cortex Microcontroller Software Interface Standard (CMSIS) hardware abstraction layer for the
Arm Cortex processor series is implemented and available for the M4 CPU.
Real-time execution is highly deterministic in thread mode, to and from sleep modes, and when handling
events at configurable priority levels via the nested vectored interrupt controller (NVIC).
Executing code from flash memory will have a wait state penalty on the nRF52 Series. An instruction cache
can be enabled to minimize flash wait states when fetching instructions. For more information on cache,
see Cache on page 27. The Electrical specification on page 21 shows CPU performance parameters
including wait states in different modes, CPU current and efficiency, and processing power and efficiency
based on the CoreMark benchmark.
The Arm system timer (SysTick) is present on nRF52840. The SysTick's clock will only tick when the CPU is
running or when the system is in debug interface mode.

4.1.1 Floating point interrupt

The floating point unit (FPU) may generate exceptions when used due to e.g. overflow or underflow, which
in turn will trigger the FPU interrupt.
See Instantiation on page 24 for more information about the exceptions triggering the FPU interrupt.
To clear the IRQ (interrupt request) line when an exception has occurred, the relevant exception bit within
the floating-point status and control register (FPSCR) needs to be cleared. For more information about the
FPSCR or other FPU registers, see Cortex-M4 Devices Generic User Guide.

4.1.2 CPU and support module configuration

The Arm Cortex-M4 processor has a number of CPU options and support modules implemented on the IC.

4413_417 v1.9 20
 Core components

Option / Module Description Implemented

Core options
NVIC Nested vector interrupt controller 48 vectors
PRIORITIES Priority bits 3
WIC Wakeup interrupt controller NO
Endianness Memory system endianness Little endian
Bit-banding Bit banded memory NO
DWT Data watchpoint and trace YES
SysTick System tick timer YES
Modules
MPU Memory protection unit YES
FPU Floating-point unit YES
DAP Debug access port YES
ETM Embedded trace macrocell YES
ITM Instrumentation trace macrocell YES
TPIU Trace port interface unit YES
ETB Embedded trace buffer NO
FPB Flash patch and breakpoint unit YES
®
HTM AMBA AHB trace macrocell NO

4.1.3 Electrical specification

4.1.3.1 CPU performance
The CPU clock speed is 64 MHz. Current and efficiency data is taken when in System ON and the CPU is
executing the CoreMark benchmark. It includes power regulator and clock base currents. All other blocks
are IDLE.

Symbol Description Min. Typ. Max. Units

WFLASH CPU wait states, running CoreMark from flash, cache disabled 2
WFLASHCACHE CPU wait states, running CoreMark from flash, cache enabled 3
WRAM CPU wait states, running CoreMark from RAM 0
CMFLASH CoreMark, running CoreMark from flash, cache enabled 212 CoreMark
CMFLASH/MHz CoreMark per MHz, running CoreMark from flash, cache enabled 3.3 CoreMark/
MHz
CMFLASH/mA CoreMark per mA, running CoreMark from flash, cache enabled, DCDC 3V 64 CoreMark/mA

4.2 Memory
The nRF52840 contains 1024 kB of flash memory and 256 kB of RAM that can be used for code and data
storage.
The CPU and peripherals with EasyDMA can access memory via the AHB multilayer interconnect. In
additon, peripherals are accessed by the CPU via the AHB multilayer interconnect, as shown in the
following figure.

4413_417 v1.9 21
 Core components

Data RAM Code RAM

System ICODE / DCODE

Section 5 0x2003 8000 0x0083 8000

Section 4 0x2003 0000 0x0083 0000
RAM8 Section 3 0x2002 8000 0x0082 8000
AHB slave Section 2
APB 0x2002 0000 0x0082 0000
AHB2APB Section 1 0x2001 8000 0x0081 8000
CPU Section 0 0x2001 0000 0x0081 0000
RAM7 Section 1
ARM Cortex-M4 0x2000 F000 0x0080 F000
AHB slave Section 0
Peripheral Peripheral 0x2000 E000 0x0080 E000
RAM6 Section 1 0x2000 D000 0x0080 D000
AHB slave Section 0
EasyDMA EasyDMA 0x2000 C000 0x0080 C000
Section 1

System bus
RAM5 0x2000 B000 0x0080 B000

DCODE

ICODE
AHB slave Section 0 0x2000 A000 0x0080 A000
DMA bus

DMA bus
RAM4 Section 1 0x2000 9000 0x0080 9000
AHB slave Section 0 0x2000 8000 0x0080 8000
RAM3 Section 1
0x2000 7000 0x0080 7000
AHB slave Section 0 0x2000 6000 0x0080 6000
RAM2 Section 1 0x2000 5000 0x0080 5000
AHB slave Section 0 0x2000 4000 0x0080 4000
RAM1 Section 1 0x2000 3000 0x0080 3000
AHB slave Section 0 0x2000 2000 0x0080 2000
RAM0 Section 1 0x2000 1000 0x0080 1000
AHB slave Section 0 0x2000 0000 0x0080 0000

Flash
ICODE/DCODE
Page 255
0x000F F000

I-Cache
slave
AHB
ICODE Page 3..254

NVMC
0x0000 3000
AHB Page 2
DCODE 0x0000 2000

slave
AHB
Page 1 0x0000 1000
AHB multilayer interconnect Page 0 0x0000 0000

Figure 2: Memory layout

See AHB multilayer on page 65 and EasyDMA on page 62 for more information about the AHB
multilayer interconnect and EasyDMA.
The same physical RAM is mapped to both the Data RAM region and the Code RAM region. It is up to the
application to partition the RAM within these regions so that one does not corrupt the other.

4.2.1 RAM - Random access memory

The RAM interface is divided into nine RAM AHB slaves.
RAM AHB slaves 0 to 7 are connected to two 4 kB RAM sections each, while RAM AHB slave 8 is connected
to six 32 kB sections, as shown in Memory layout on page 22.
Each RAM section has separate power control for System ON and System OFF mode operation, which is
configured via RAM register (see the POWER — Power supply on page 80).

4.2.2 Flash - Non-volatile memory

The CPU can read from flash memory an unlimited number of times, but is restricted in how it writes to
flash and the number of writes and erases it can perform.
Writing to flash memory is managed by the non-volatile memory controller (NVMC), see NVMC — Non-
volatile memory controller on page 25.
Flash memory is divided into 256 pages of 4 kB each that can be accessed by the CPU via the ICODE and
DCODE buses as shown in Memory layout on page 22.

4.2.3 Memory map

The complete memory map for the nRF52840 is shown in the following figure. As described in Memory on
page 21, Code RAM and Data RAM are the same physical RAM.

4413_417 v1.9 22
 Core components

System address map Address map

0xFFFFFFFF

Device
Private peripheral bus
0xE0000000 0xE0000000

Device

0xC0000000

Device

0xA0000000

RAM

0x80000000

RAM

0x60000000
AHB peripherals
Peripheral 0x50000000
APB peripherals
0x40000000 0x40000000

SRAM
Data RAM
0x20000000 0x20000000
XIP 0x19FFFFFF
Code 0x12000000
UICR 0x10001000
FICR 0x10000000
0x00000000
Code RAM 0x00800000
Flash 0x00000000

Figure 3: Memory map

4413_417 v1.9 23
 Core components

4.2.4 Instantiation

ID Base address Instance Description

0 0x40000000 APPROTECT APPROTECT control
0 0x40000000 CLOCK Clock control
0 0x40000000 POWER Power control
0 0x50000000 GPIO General purpose input and output

This instance is deprecated.

0 0x50000000 P0 General purpose input and output, port 0
0 0x50000300 P1 General purpose input and output, port 1
1 0x40001000 RADIO 2.4 GHz radio
2 0x40002000 UART0 Universal asynchronous receiver/transmitter

This instance is deprecated.

2 0x40002000 UARTE0 Universal asynchronous receiver/transmitter with EasyDMA, unit 0
3 0x40003000 SPI0 SPI master 0

This instance is deprecated.

3 0x40003000 SPIM0 SPI master 0
3 0x40003000 SPIS0 SPI slave 0
3 0x40003000 TWI0 Two-wire interface master 0

This instance is deprecated.

3 0x40003000 TWIM0 Two-wire interface master 0
3 0x40003000 TWIS0 Two-wire interface slave 0
4 0x40004000 SPI1 SPI master 1

This instance is deprecated.

4 0x40004000 SPIM1 SPI master 1
4 0x40004000 SPIS1 SPI slave 1
4 0x40004000 TWI1 Two-wire interface master 1

This instance is deprecated.

4 0x40004000 TWIM1 Two-wire interface master 1
4 0x40004000 TWIS1 Two-wire interface slave 1
5 0x40005000 NFCT Near field communication tag
6 0x40006000 GPIOTE GPIO tasks and events
7 0x40007000 SAADC Analog to digital converter
8 0x40008000 TIMER0 Timer 0
9 0x40009000 TIMER1 Timer 1
10 0x4000A000 TIMER2 Timer 2
11 0x4000B000 RTC0 Real-time counter 0
12 0x4000C000 TEMP Temperature sensor
13 0x4000D000 RNG Random number generator
14 0x4000E000 ECB AES electronic code book (ECB) mode block encryption
15 0x4000F000 AAR Accelerated address resolver
15 0x4000F000 CCM AES counter with CBC-MAC (CCM) mode block encryption
16 0x40010000 WDT Watchdog timer
17 0x40011000 RTC1 Real-time counter 1
18 0x40012000 QDEC Quadrature decoder
19 0x40013000 COMP General purpose comparator
19 0x40013000 LPCOMP Low power comparator
20 0x40014000 EGU0 Event generator unit 0
20 0x40014000 SWI0 Software interrupt 0
21 0x40015000 EGU1 Event generator unit 1
21 0x40015000 SWI1 Software interrupt 1

4413_417 v1.9 24
 Core components

ID Base address Instance Description

22 0x40016000 EGU2 Event generator unit 2
22 0x40016000 SWI2 Software interrupt 2
23 0x40017000 EGU3 Event generator unit 3
23 0x40017000 SWI3 Software interrupt 3
24 0x40018000 EGU4 Event generator unit 4
24 0x40018000 SWI4 Software interrupt 4
25 0x40019000 EGU5 Event generator unit 5
25 0x40019000 SWI5 Software interrupt 5
26 0x4001A000 TIMER3 Timer 3
27 0x4001B000 TIMER4 Timer 4
28 0x4001C000 PWM0 Pulse width modulation unit 0
29 0x4001D000 PDM Pulse Density modulation (digital microphone) interface
30 0x4001E000 ACL Access control lists
30 0x4001E000 NVMC Non-volatile memory controller
31 0x4001F000 PPI Programmable peripheral interconnect
32 0x40020000 MWU Memory watch unit
33 0x40021000 PWM1 Pulse width modulation unit 1
34 0x40022000 PWM2 Pulse width modulation unit 2
35 0x40023000 SPI2 SPI master 2

This instance is deprecated.

35 0x40023000 SPIM2 SPI master 2
35 0x40023000 SPIS2 SPI slave 2
36 0x40024000 RTC2 Real-time counter 2
37 0x40025000 I2S Inter-IC sound interface
38 0x40026000 FPU FPU interrupt
39 0x40027000 USBD Universal serial bus device
40 0x40028000 UARTE1 Universal asynchronous receiver/transmitter with EasyDMA, unit 1
41 0x40029000 QSPI External memory interface
42 0x5002A000 CC_HOST_RGF Host platform interface
42 0x5002A000 CRYPTOCELL CRYPTOCELL control interface
45 0x4002D000 PWM3 Pulse width modulation unit 3
47 0x4002F000 SPIM3 SPI master 3
N/A 0x10000000 FICR Factory information configuration
N/A 0x10001000 UICR User information configuration

Table 3: Instantiation table

4.3 NVMC — Non-volatile memory controller

The non-volatile memory controller (NVMC) is used for writing and erasing of the internal flash memory
and the UICR (user information configuration registers).
The CONFIG on page 28 is used to enable the NVMC for writing (CONFIG.WEN = Wen) and erasing
(CONFIG.WEN = Een).
The CPU must be halted before initiating a NVMC operation from the debug system.

4.3.1 Writing to flash

When write is enabled, full 32-bit words can be written to word-aligned addresses in flash memory.
As illustrated in Memory on page 21, the flash is divided into multiple pages. The same 32-bit word in
flash memory can only be written n WRITE number of times before a page erase must be performed.

4413_417 v1.9 25
 Core components

The NVMC is only able to write 0 to bits in flash memory that are erased (set to 1). It cannot rewrite a bit
back to 1. Only full 32-bit words can be written to flash memory using the NVMC interface. To write less
than 32 bits, write the data as a full 32-bit word and set all the bits that should remain unchanged in the
word to 1. The restriction on the number of writes (nWRITE) still applies in this case.
Only word-aligned writes are allowed. Byte or half-word-aligned writes will result in a hard fault.
The time it takes to write a word to flash is specified by tWRITE. The CPU is halted if the CPU executes code
from the flash while the NVMC is writing to the flash.
NVM writing time can be reduced by using READYNEXT. If this status bit is set to 1, code can perform
the next data write to the flash. This write will be buffered and will be taken into account as soon as the
ongoing write operation is completed.

4.3.2 Erasing a page in flash

When erase is enabled, the flash memory can be erased page by page using the ERASEPAGE on page
29.
After erasing a flash page, all bits in the page are set to 1. The time it takes to erase a page is specified
by tERASEPAGE. The CPU is halted if the CPU executes code from the flash while the NVMC is writing to the
flash.
See Partial erase of a page in flash on page 27 for information on dividing the page erase time into
shorter chunks.

4.3.3 Writing to user information configuration registers (UICR)

User information configuration registers (UICR) are written in the same way as flash. After UICR has been
written, the new UICR configuration will only take effect after a reset.
UICR can only be written nWRITE number of times before an erase must be performed using ERASEUICR on
page 29 or ERASEALL on page 29. The time it takes to write a word to UICR is specified by tWRITE.
The CPU is halted if the CPU executes code from the flash while the NVMC is writing to the UICR.

4.3.4 Erasing user information configuration registers (UICR)

When erase is enabled, UICR can be erased using the ERASEUICR on page 29.
After erasing UICR, all bits in UICR are set to 1. The time it takes to erase UICR is specified by tERASEPAGE.
The CPU is halted if the CPU executes code from the flash while the NVMC performs the erase operation.

4.3.5 Erase all

When erase is enabled, flash and UICR can be erased completely in one operation by using the ERASEALL
on page 29. This operation will not erase the factory information configuration registers (FICR).
The time it takes to perform an ERASEALL command is specified by tERASEALL. The CPU is halted if the CPU
executes code from the flash while the NVMC performs the erase operation.

4.3.6 Access port protection behavior

When access port protection is enabled, parts of the NVMC functionality will be blocked in order to
prevent intentional or unintentional erase of UICR.

4413_417 v1.9 26
 Core components

CTRL-AP ERASEALL NVMC ERASEPAGE NVMC ERASEPAGE NVMC ERASEALL NVMC ERASEUICR
PARTIAL

APPROTECT
Disabled Allowed Allowed Allowed Allowed Allowed
Enabled Allowed Allowed Allowed Allowed Blocked

Table 4: NVMC Protection

4.3.7 Partial erase of a page in flash

Partial erase is a feature in the NVMC to split a page erase time into shorter chunks to prevent longer CPU
stalls in time-critical applications. Partial erase is only applicable to the code area in flash memory and
does not work with UICR.
When erase is enabled, the partial erase of a flash page can be started by writing to ERASEPAGEPARTIAL
on page 30. The duration of a partial erase can be configured in ERASEPAGEPARTIALCFG on page
30. A flash page is erased when its erase time reaches tERASEPAGE. Use ERASEPAGEPARTIAL N number
of times so that N * ERASEPAGEPARTIALCFG ≥ tERASEPAGE, where N * ERASEPAGEPARTIALCFG gives the
cumulative (total) erase time. Every time the cumulative erase time reaches tERASEPAGE, it counts as one
erase cycle.
After the erase is complete, all bits in the page are set to 1. The CPU is halted if the CPU executes code
from the flash while the NVMC performs the partial erase operation.
The bits in the page are undefined if the flash page erase is incomplete, i.e. if a partial erase has started
but the total erase time is less than tERASEPAGE.

4.3.8 Cache
An instruction cache (I-Cache) can be enabled for the ICODE bus in the NVMC.
A cache hit is an instruction fetch from the cache, and it has a 0 wait-state delay. The number of wait-
states for a cache miss, where the instruction is not available in the cache and needs to be fetched from
flash, is shown in CPU on page 20.
Enabling the cache can increase CPU performance and reduce power consumption by reducing the
number of wait cycles and the number of flash accesses. This will depend on the cache hit rate. Cache will
use some current when enabled. If the reduction in average current due to reduced flash accesses is larger
than the cache power requirement, the average current to execute the program code will decrease.
When disabled, the cache does not use current and does not retain its content.
It is possible to enable cache profiling to analyze the performance of the cache for your program using
the ICACHECNF register. When profiling is enabled, the IHIT and IMISS registers are incremented for every
instruction cache hit or miss, respectively. The hit and miss profiling registers do not wrap around after
reaching the maximum value. If the maximum value is reached, consider profiling for a shorter duration to
get correct numbers.

4.3.9 Registers
Instances

Instance Base address Description

NVMC 0x4001E000 Non-volatile memory controller

4413_417 v1.9 27
 Core components

Register overview

Register Offset Description

READY 0x400 Ready flag
READYNEXT 0x408 Ready flag
CONFIG 0x504 Configuration register
ERASEPAGE 0x508 Register for erasing a page in code area
ERASEALL 0x50C Register for erasing all non-volatile user memory
ERASEUICR 0x514 Register for erasing user information configuration registers
ERASEPAGEPARTIAL 0x518 Register for partial erase of a page in code area
ERASEPAGEPARTIALCFG 0x51C Register for partial erase configuration
ICACHECNF 0x540 I-code cache configuration register
IHIT 0x548 I-code cache hit counter
IMISS 0x54C I-code cache miss counter

4.3.9.1 READY
Address offset: 0x400
Ready flag

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000001 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
ID R/W Field Value ID Value Description
A R READY NVMC is ready or busy
Busy 0 NVMC is busy (on-going write or erase operation)
Ready 1 NVMC is ready

4.3.9.2 READYNEXT
Address offset: 0x408
Ready flag

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000001 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
ID R/W Field Value ID Value Description
A R READYNEXT NVMC can accept a new write operation
Busy 0 NVMC cannot accept any write operation
Ready 1 NVMC is ready

4.3.9.3 CONFIG
Address offset: 0x504
Configuration register

4413_417 v1.9 28
 Core components

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW WEN Program memory access mode. It is strongly recommended to only activate
erase and write modes when they are actively used.

Enabling write or erase will invalidate the cache and keep it invalidated.
Ren 0 Read only access
Wen 1 Write enabled
Een 2 Erase enabled

4.3.9.4 ERASEPAGE
Address offset: 0x508
Register for erasing a page in code area

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W ERASEPAGE Register for starting erase of a page in code area

The value is the address to the page to be erased. (Addresses of first word
in page). The erase must be enabled using CONFIG.WEN before the page
can be erased. Attempts to erase pages that are outside the code area may
result in undesirable behavior, e.g. the wrong page may be erased.

4.3.9.5 ERASEALL
Address offset: 0x50C
Register for erasing all non-volatile user memory

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W ERASEALL Erase all non-volatile memory including UICR registers. The erase must be
enabled using CONFIG.WEN before the non-volatile memory can be erased.
NoOperation 0 No operation
Erase 1 Start chip erase

4.3.9.6 ERASEUICR
Address offset: 0x514
Register for erasing user information configuration registers

4413_417 v1.9 29
 Core components

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W ERASEUICR Register starting erase of all user information configuration registers. The
erase must be enabled using CONFIG.WEN before the UICR can be erased.
NoOperation 0 No operation
Erase 1 Start erase of UICR

4.3.9.7 ERASEPAGEPARTIAL
Address offset: 0x518
Register for partial erase of a page in code area

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W ERASEPAGEPARTIAL Register for starting partial erase of a page in code area

The value is the address to the page to be partially erased (address of the
first word in page). The erase must be enabled using CONFIG.WEN before
every erase page partial and disabled using CONFIG.WEN after every erase
page partial. Attempts to erase pages that are outside the code area may
result in undesirable behavior, e.g. the wrong page may be erased.

4.3.9.8 ERASEPAGEPARTIALCFG
Address offset: 0x51C
Register for partial erase configuration

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x0000000A 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 0
ID R/W Field Value ID Value Description
A RW DURATION Duration of the partial erase in milliseconds

The user must ensure that the total erase time is long enough for a
complete erase of the flash page.

4.3.9.9 ICACHECNF
Address offset: 0x540
I-code cache configuration register

4413_417 v1.9 30
 Core components

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW CACHEEN Cache enable
Disabled 0 Disable cache. Invalidates all cache entries.
Enabled 1 Enable cache
B RW CACHEPROFEN Cache profiling enable
Disabled 0 Disable cache profiling
Enabled 1 Enable cache profiling

4.3.9.10 IHIT
Address offset: 0x548
I-code cache hit counter

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW HITS Number of cache hits.

Register is writable, but only to '0'.

4.3.9.11 IMISS
Address offset: 0x54C
I-code cache miss counter

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW MISSES Number of cache misses.

Register is writable, but only to '0'.

4.3.10 Electrical specification

4.3.10.1 Flash programming

Symbol Description Min. Typ. Max. Units

nWRITE Number of times a 32-bit word can be written before erase 2
nENDURANCE Erase cycles per page 10000
tWRITE Time to write one 32-bit word 411 µs

tERASEPAGE Time to erase one page 85 1 ms

tERASEALL Time to erase all flash 1691 ms

tERASEPAGEPARTIAL,acc Accuracy of the partial page erase duration. Total execution time for one 1.051
partial page erase is defined as ERASEPAGEPARTIALCFG * tERASEPAGEPARTIAL,acc.

1
Applies when HFXO is used. Timing varies according to HFINT accuracy when HFINT is used.

4413_417 v1.9 31
 Core components

4.3.10.2 Cache size

Symbol Description Min. Typ. Max. Units

SizeICODE I-Code cache size 2048 Bytes

4.4 FICR — Factory information configuration registers

Factory information configuration registers (FICR) are pre-programmed in factory and cannot be erased by
the user. These registers contain chip-specific information and configuration.

4.4.1 Registers
Instances

Instance Base address Description

FICR 0x10000000 Factory information configuration

Register overview

Register Offset Description

CODEPAGESIZE 0x010 Code memory page size
CODESIZE 0x014 Code memory size
DEVICEID[0] 0x060 Device identifier
DEVICEID[1] 0x064 Device identifier
ER[0] 0x080 Encryption root, word 0
ER[1] 0x084 Encryption root, word 1
ER[2] 0x088 Encryption root, word 2
ER[3] 0x08C Encryption root, word 3
IR[0] 0x090 Identity Root, word 0
IR[1] 0x094 Identity Root, word 1
IR[2] 0x098 Identity Root, word 2
IR[3] 0x09C Identity Root, word 3
DEVICEADDRTYPE 0x0A0 Device address type
DEVICEADDR[0] 0x0A4 Device address 0
DEVICEADDR[1] 0x0A8 Device address 1
INFO.PART 0x100 Part code
INFO.VARIANT 0x104 Build code, last two letters of Package Variant and first two characters of Build Code, encoded in
ASCII.
INFO.PACKAGE 0x108 Package option
INFO.RAM 0x10C RAM variant
INFO.FLASH 0x110 Flash variant
PRODTEST[0] 0x350 Production test signature 0
PRODTEST[1] 0x354 Production test signature 1
PRODTEST[2] 0x358 Production test signature 2
TEMP.A0 0x404 Slope definition A0
TEMP.A1 0x408 Slope definition A1
TEMP.A2 0x40C Slope definition A2
TEMP.A3 0x410 Slope definition A3
TEMP.A4 0x414 Slope definition A4
TEMP.A5 0x418 Slope definition A5

4413_417 v1.9 32
 Core components

Register Offset Description

TEMP.B0 0x41C Y-intercept B0
TEMP.B1 0x420 Y-intercept B1
TEMP.B2 0x424 Y-intercept B2
TEMP.B3 0x428 Y-intercept B3
TEMP.B4 0x42C Y-intercept B4
TEMP.B5 0x430 Y-intercept B5
TEMP.T0 0x434 Segment end T0
TEMP.T1 0x438 Segment end T1
TEMP.T2 0x43C Segment end T2
TEMP.T3 0x440 Segment end T3
TEMP.T4 0x444 Segment end T4
NFC.TAGHEADER0 0x450 Default header for NFC tag. Software can read these values to populate NFCID1_3RD_LAST,
NFCID1_2ND_LAST, and NFCID1_LAST.
NFC.TAGHEADER1 0x454 Default header for NFC tag. Software can read these values to populate NFCID1_3RD_LAST,
NFCID1_2ND_LAST, and NFCID1_LAST.
NFC.TAGHEADER2 0x458 Default header for NFC tag. Software can read these values to populate NFCID1_3RD_LAST,
NFCID1_2ND_LAST, and NFCID1_LAST.
NFC.TAGHEADER3 0x45C Default header for NFC tag. Software can read these values to populate NFCID1_3RD_LAST,
NFCID1_2ND_LAST, and NFCID1_LAST.
TRNG90B.BYTES 0xC00 Amount of bytes for the required entropy bits
TRNG90B.RCCUTOFF 0xC04 Repetition counter cutoff
TRNG90B.APCUTOFF 0xC08 Adaptive proportion cutoff
TRNG90B.STARTUP 0xC0C Amount of bytes for the startup tests
TRNG90B.ROSC1 0xC10 Sample count for ring oscillator 1
TRNG90B.ROSC2 0xC14 Sample count for ring oscillator 2
TRNG90B.ROSC3 0xC18 Sample count for ring oscillator 3
TRNG90B.ROSC4 0xC1C Sample count for ring oscillator 4

4.4.1.1 CODEPAGESIZE
Address offset: 0x010
Code memory page size

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R CODEPAGESIZE Code memory page size

4.4.1.2 CODESIZE
Address offset: 0x014
Code memory size

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R CODESIZE Code memory size in number of pages

Total code space is: CODEPAGESIZE * CODESIZE

4413_417 v1.9 33
 Core components

4.4.1.3 DEVICEID[0]
Address offset: 0x060
Device identifier

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R DEVICEID 64 bit unique device identifier

DEVICEID[0] contains the least significant bits of the device identifier.

DEVICEID[1] contains the most significant bits of the device identifier.

4.4.1.4 DEVICEID[1]
Address offset: 0x064
Device identifier

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R DEVICEID 64 bit unique device identifier

DEVICEID[0] contains the least significant bits of the device identifier.

DEVICEID[1] contains the most significant bits of the device identifier.

4.4.1.5 ER[0]
Address offset: 0x080
Encryption root, word 0

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R ER Encryption root, word 0

4.4.1.6 ER[1]
Address offset: 0x084
Encryption root, word 1

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R ER Encryption root, word 1

4.4.1.7 ER[2]
Address offset: 0x088

4413_417 v1.9 34
 Core components

Encryption root, word 2

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A
Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R ER Encryption root, word 2

4.4.1.8 ER[3]
Address offset: 0x08C
Encryption root, word 3

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R ER Encryption root, word 3

4.4.1.9 IR[0]
Address offset: 0x090
Identity Root, word 0

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R IR Identity Root, word 0

4.4.1.10 IR[1]
Address offset: 0x094
Identity Root, word 1

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R IR Identity Root, word 1

4.4.1.11 IR[2]
Address offset: 0x098
Identity Root, word 2

4413_417 v1.9 35
 Core components

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R IR Identity Root, word 2

4.4.1.12 IR[3]
Address offset: 0x09C
Identity Root, word 3

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R IR Identity Root, word 3

4.4.1.13 DEVICEADDRTYPE
Address offset: 0x0A0
Device address type

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R DEVICEADDRTYPE Device address type
Public 0 Public address
Random 1 Random address

4.4.1.14 DEVICEADDR[0]
Address offset: 0x0A4
Device address 0

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R DEVICEADDR 48 bit device address

DEVICEADDR[0] contains the least significant bits of the device address.

DEVICEADDR[1] contains the most significant bits of the device address.
Only bits [15:0] of DEVICEADDR[1] are used.

4.4.1.15 DEVICEADDR[1]
Address offset: 0x0A8
Device address 1

4413_417 v1.9 36
 Core components

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R DEVICEADDR 48 bit device address

DEVICEADDR[0] contains the least significant bits of the device address.

DEVICEADDR[1] contains the most significant bits of the device address.
Only bits [15:0] of DEVICEADDR[1] are used.

4.4.1.16 INFO
Device info

4.4.1.16.1 INFO.PART
Address offset: 0x100
Part code

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00052840 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 0 1 0 1 0 0 0 0 1 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R PART Part code
N52840 0x52840 nRF52840
Unspecified 0xFFFFFFFF Unspecified

4.4.1.16.2 INFO.VARIANT
Address offset: 0x104
Build code, last two letters of Package Variant and first two characters of Build Code, encoded in ASCII.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R VARIANT For valid values see SoC revisions and variants.

4.4.1.16.3 INFO.PACKAGE
Address offset: 0x108
Package option

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R PACKAGE Package option
QI 0x2004 QIxx - 7x7 73-pin aQFN
QF 0x2000 QFxx - 6x6 48-pin QFN
CK 0x2005 CKxx - 3.544 x 3.607 WLCSP
Unspecified 0xFFFFFFFF Unspecified

4413_417 v1.9 37
 Core components

4.4.1.16.4 INFO.RAM
Address offset: 0x10C
RAM variant

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R RAM RAM variant
K16 0x10 16 kB RAM
K32 0x20 32 kB RAM
K64 0x40 64 kB RAM
K128 0x80 128 kB RAM
K256 0x100 256 kB RAM
Unspecified 0xFFFFFFFF Unspecified

4.4.1.16.5 INFO.FLASH
Address offset: 0x110
Flash variant

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R FLASH Flash variant
K128 0x80 128 kB FLASH
K256 0x100 256 kB FLASH
K512 0x200 512 kB FLASH
K1024 0x400 1 MB FLASH
K2048 0x800 2 MB FLASH
Unspecified 0xFFFFFFFF Unspecified

4.4.1.17 PRODTEST[0]
Address offset: 0x350
Production test signature 0

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R PRODTEST Production test signature 0
Done 0xBB42319F Production tests done
NotDone 0xFFFFFFFF Production tests not done

4.4.1.18 PRODTEST[1]
Address offset: 0x354
Production test signature 1

4413_417 v1.9 38
 Core components

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R PRODTEST Production test signature 1
Done 0xBB42319F Production tests done
NotDone 0xFFFFFFFF Production tests not done

4.4.1.19 PRODTEST[2]
Address offset: 0x358
Production test signature 2

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R PRODTEST Production test signature 2
Done 0xBB42319F Production tests done
NotDone 0xFFFFFFFF Production tests not done

4.4.1.20 TEMP
Registers storing factory TEMP module linearization coefficients

4.4.1.20.1 TEMP.A0
Address offset: 0x404
Slope definition A0

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R A A (slope definition) register.

4.4.1.20.2 TEMP.A1
Address offset: 0x408
Slope definition A1

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R A A (slope definition) register.

4.4.1.20.3 TEMP.A2
Address offset: 0x40C
Slope definition A2

4413_417 v1.9 39
 Core components

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R A A (slope definition) register.

4.4.1.20.4 TEMP.A3
Address offset: 0x410
Slope definition A3

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R A A (slope definition) register.

4.4.1.20.5 TEMP.A4
Address offset: 0x414
Slope definition A4

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R A A (slope definition) register.

4.4.1.20.6 TEMP.A5
Address offset: 0x418
Slope definition A5

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R A A (slope definition) register.

4.4.1.20.7 TEMP.B0
Address offset: 0x41C
Y-intercept B0

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R B B (y-intercept)

4413_417 v1.9 40
 Core components

4.4.1.20.8 TEMP.B1
Address offset: 0x420
Y-intercept B1

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R B B (y-intercept)

4.4.1.20.9 TEMP.B2
Address offset: 0x424
Y-intercept B2

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R B B (y-intercept)

4.4.1.20.10 TEMP.B3
Address offset: 0x428
Y-intercept B3

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R B B (y-intercept)

4.4.1.20.11 TEMP.B4
Address offset: 0x42C
Y-intercept B4

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R B B (y-intercept)

4.4.1.20.12 TEMP.B5
Address offset: 0x430
Y-intercept B5

4413_417 v1.9 41
 Core components

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R B B (y-intercept)

4.4.1.20.13 TEMP.T0
Address offset: 0x434
Segment end T0

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R T T (segment end) register

4.4.1.20.14 TEMP.T1
Address offset: 0x438
Segment end T1

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R T T (segment end) register

4.4.1.20.15 TEMP.T2
Address offset: 0x43C
Segment end T2

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R T T (segment end) register

4.4.1.20.16 TEMP.T3
Address offset: 0x440
Segment end T3

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R T T (segment end) register

4413_417 v1.9 42
 Core components

4.4.1.20.17 TEMP.T4
Address offset: 0x444
Segment end T4

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R T T (segment end) register

4.4.1.21 NFC.TAGHEADER0
Address offset: 0x450
Default header for NFC tag. Software can read these values to populate NFCID1_3RD_LAST,
NFCID1_2ND_LAST, and NFCID1_LAST.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID D D D D D D D D C C C C C C C C B B B B B B B B A A A A A A A A

Reset 0xFFFFFF5F 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 1 0 1 1 1 1 1
ID R/W Field Value ID Value Description
A R MFGID Default Manufacturer ID: Nordic Semiconductor ASA has ICM 0x5F
B R UD1 Unique identifier byte 1
C R UD2 Unique identifier byte 2
D R UD3 Unique identifier byte 3

4.4.1.22 NFC.TAGHEADER1
Address offset: 0x454
Default header for NFC tag. Software can read these values to populate NFCID1_3RD_LAST,
NFCID1_2ND_LAST, and NFCID1_LAST.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID D D D D D D D D C C C C C C C C B B B B B B B B A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R UD4 Unique identifier byte 4
B R UD5 Unique identifier byte 5
C R UD6 Unique identifier byte 6
D R UD7 Unique identifier byte 7

4.4.1.23 NFC.TAGHEADER2
Address offset: 0x458
Default header for NFC tag. Software can read these values to populate NFCID1_3RD_LAST,
NFCID1_2ND_LAST, and NFCID1_LAST.

4413_417 v1.9 43
 Core components

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID D D D D D D D D C C C C C C C C B B B B B B B B A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R UD8 Unique identifier byte 8
B R UD9 Unique identifier byte 9
C R UD10 Unique identifier byte 10
D R UD11 Unique identifier byte 11

4.4.1.24 NFC.TAGHEADER3
Address offset: 0x45C
Default header for NFC tag. Software can read these values to populate NFCID1_3RD_LAST,
NFCID1_2ND_LAST, and NFCID1_LAST.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID D D D D D D D D C C C C C C C C B B B B B B B B A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R UD12 Unique identifier byte 12
B R UD13 Unique identifier byte 13
C R UD14 Unique identifier byte 14
D R UD15 Unique identifier byte 15

4.4.1.25 TRNG90B
NIST800-90B RNG calibration data

4.4.1.25.1 TRNG90B.BYTES
Address offset: 0xC00
Amount of bytes for the required entropy bits

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R BYTES Amount of bytes for the required entropy bits

4.4.1.25.2 TRNG90B.RCCUTOFF
Address offset: 0xC04
Repetition counter cutoff

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R RCCUTOFF Repetition counter cutoff

4.4.1.25.3 TRNG90B.APCUTOFF
Address offset: 0xC08

4413_417 v1.9 44
 Core components

Adaptive proportion cutoff

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A
Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R APCUTOFF Adaptive proportion cutoff

4.4.1.25.4 TRNG90B.STARTUP
Address offset: 0xC0C
Amount of bytes for the startup tests

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R STARTUP Amount of bytes for the startup tests

4.4.1.25.5 TRNG90B.ROSC1
Address offset: 0xC10
Sample count for ring oscillator 1

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R ROSC1 Sample count for ring oscillator 1

4.4.1.25.6 TRNG90B.ROSC2
Address offset: 0xC14
Sample count for ring oscillator 2

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R ROSC2 Sample count for ring oscillator 2

4.4.1.25.7 TRNG90B.ROSC3
Address offset: 0xC18
Sample count for ring oscillator 3

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R ROSC3 Sample count for ring oscillator 3

4413_417 v1.9 45
 Core components

4.4.1.25.8 TRNG90B.ROSC4
Address offset: 0xC1C
Sample count for ring oscillator 4

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A R ROSC4 Sample count for ring oscillator 4

4.5 UICR — User information configuration registers

The user information configuration registers (UICRs) are non-volatile memory (NVM) registers for
configuring user-specific settings.
For information on writing UICR registers, see the NVMC — Non-volatile memory controller on page
25 and Memory on page 21 chapters.

4.5.1 Registers
Instances

Instance Base address Description

UICR 0x10001000 User information configuration

Register overview

Register Offset Description

NRFFW[0] 0x014 Reserved for Nordic firmware design
NRFFW[1] 0x018 Reserved for Nordic firmware design
NRFFW[2] 0x01C Reserved for Nordic firmware design
NRFFW[3] 0x020 Reserved for Nordic firmware design
NRFFW[4] 0x024 Reserved for Nordic firmware design
NRFFW[5] 0x028 Reserved for Nordic firmware design
NRFFW[6] 0x02C Reserved for Nordic firmware design
NRFFW[7] 0x030 Reserved for Nordic firmware design
NRFFW[8] 0x034 Reserved for Nordic firmware design
NRFFW[9] 0x038 Reserved for Nordic firmware design
NRFFW[10] 0x03C Reserved for Nordic firmware design
NRFFW[11] 0x040 Reserved for Nordic firmware design
NRFFW[12] 0x044 Reserved for Nordic firmware design
NRFHW[0] 0x050 Reserved for Nordic hardware design
NRFHW[1] 0x054 Reserved for Nordic hardware design
NRFHW[2] 0x058 Reserved for Nordic hardware design
NRFHW[3] 0x05C Reserved for Nordic hardware design
NRFHW[4] 0x060 Reserved for Nordic hardware design
NRFHW[5] 0x064 Reserved for Nordic hardware design
NRFHW[6] 0x068 Reserved for Nordic hardware design
NRFHW[7] 0x06C Reserved for Nordic hardware design
NRFHW[8] 0x070 Reserved for Nordic hardware design

4413_417 v1.9 46
 Core components

Register Offset Description

NRFHW[9] 0x074 Reserved for Nordic hardware design
NRFHW[10] 0x078 Reserved for Nordic hardware design
NRFHW[11] 0x07C Reserved for Nordic hardware design
CUSTOMER[0] 0x080 Reserved for customer
CUSTOMER[1] 0x084 Reserved for customer
CUSTOMER[2] 0x088 Reserved for customer
CUSTOMER[3] 0x08C Reserved for customer
CUSTOMER[4] 0x090 Reserved for customer
CUSTOMER[5] 0x094 Reserved for customer
CUSTOMER[6] 0x098 Reserved for customer
CUSTOMER[7] 0x09C Reserved for customer
CUSTOMER[8] 0x0A0 Reserved for customer
CUSTOMER[9] 0x0A4 Reserved for customer
CUSTOMER[10] 0x0A8 Reserved for customer
CUSTOMER[11] 0x0AC Reserved for customer
CUSTOMER[12] 0x0B0 Reserved for customer
CUSTOMER[13] 0x0B4 Reserved for customer
CUSTOMER[14] 0x0B8 Reserved for customer
CUSTOMER[15] 0x0BC Reserved for customer
CUSTOMER[16] 0x0C0 Reserved for customer
CUSTOMER[17] 0x0C4 Reserved for customer
CUSTOMER[18] 0x0C8 Reserved for customer
CUSTOMER[19] 0x0CC Reserved for customer
CUSTOMER[20] 0x0D0 Reserved for customer
CUSTOMER[21] 0x0D4 Reserved for customer
CUSTOMER[22] 0x0D8 Reserved for customer
CUSTOMER[23] 0x0DC Reserved for customer
CUSTOMER[24] 0x0E0 Reserved for customer
CUSTOMER[25] 0x0E4 Reserved for customer
CUSTOMER[26] 0x0E8 Reserved for customer
CUSTOMER[27] 0x0EC Reserved for customer
CUSTOMER[28] 0x0F0 Reserved for customer
CUSTOMER[29] 0x0F4 Reserved for customer
CUSTOMER[30] 0x0F8 Reserved for customer
CUSTOMER[31] 0x0FC Reserved for customer
PSELRESET[0] 0x200 Mapping of the nRESET function (see POWER chapter for details)
PSELRESET[1] 0x204 Mapping of the nRESET function (see POWER chapter for details)
APPROTECT 0x208 Access port protection
NFCPINS 0x20C Setting of pins dedicated to NFC functionality: NFC antenna or GPIO
DEBUGCTRL 0x210 Processor debug control
REGOUT0 0x304 Output voltage from REG0 regulator stage. The maximum output voltage from this stage is given as
VDDH - V_VDDH-VDD.

4.5.1.1 NRFFW[0]
Address offset: 0x014
Reserved for Nordic firmware design

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW NRFFW Reserved for Nordic firmware design

4413_417 v1.9 47
 Core components

4.5.1.2 NRFFW[1]
Address offset: 0x018
Reserved for Nordic firmware design

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW NRFFW Reserved for Nordic firmware design

4.5.1.3 NRFFW[2]
Address offset: 0x01C
Reserved for Nordic firmware design

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW NRFFW Reserved for Nordic firmware design

4.5.1.4 NRFFW[3]
Address offset: 0x020
Reserved for Nordic firmware design

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW NRFFW Reserved for Nordic firmware design

4.5.1.5 NRFFW[4]
Address offset: 0x024
Reserved for Nordic firmware design

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW NRFFW Reserved for Nordic firmware design

4.5.1.6 NRFFW[5]
Address offset: 0x028
Reserved for Nordic firmware design

4413_417 v1.9 48
 Core components

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW NRFFW Reserved for Nordic firmware design

4.5.1.7 NRFFW[6]
Address offset: 0x02C
Reserved for Nordic firmware design

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW NRFFW Reserved for Nordic firmware design

4.5.1.8 NRFFW[7]
Address offset: 0x030
Reserved for Nordic firmware design

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW NRFFW Reserved for Nordic firmware design

4.5.1.9 NRFFW[8]
Address offset: 0x034
Reserved for Nordic firmware design

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW NRFFW Reserved for Nordic firmware design

4.5.1.10 NRFFW[9]
Address offset: 0x038
Reserved for Nordic firmware design

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW NRFFW Reserved for Nordic firmware design

4413_417 v1.9 49
 Core components

4.5.1.11 NRFFW[10]
Address offset: 0x03C
Reserved for Nordic firmware design

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW NRFFW Reserved for Nordic firmware design

4.5.1.12 NRFFW[11]
Address offset: 0x040
Reserved for Nordic firmware design

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW NRFFW Reserved for Nordic firmware design

4.5.1.13 NRFFW[12]
Address offset: 0x044
Reserved for Nordic firmware design

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW NRFFW Reserved for Nordic firmware design

4.5.1.14 NRFHW[0]
Address offset: 0x050
Reserved for Nordic hardware design

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW NRFHW Reserved for Nordic hardware design

4.5.1.15 NRFHW[1]
Address offset: 0x054
Reserved for Nordic hardware design

4413_417 v1.9 50
 Core components

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW NRFHW Reserved for Nordic hardware design

4.5.1.16 NRFHW[2]
Address offset: 0x058
Reserved for Nordic hardware design

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW NRFHW Reserved for Nordic hardware design

4.5.1.17 NRFHW[3]
Address offset: 0x05C
Reserved for Nordic hardware design

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW NRFHW Reserved for Nordic hardware design

4.5.1.18 NRFHW[4]
Address offset: 0x060
Reserved for Nordic hardware design

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW NRFHW Reserved for Nordic hardware design

4.5.1.19 NRFHW[5]
Address offset: 0x064
Reserved for Nordic hardware design

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW NRFHW Reserved for Nordic hardware design

4413_417 v1.9 51
 Core components

4.5.1.20 NRFHW[6]
Address offset: 0x068
Reserved for Nordic hardware design

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW NRFHW Reserved for Nordic hardware design

4.5.1.21 NRFHW[7]
Address offset: 0x06C
Reserved for Nordic hardware design

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW NRFHW Reserved for Nordic hardware design

4.5.1.22 NRFHW[8]
Address offset: 0x070
Reserved for Nordic hardware design

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW NRFHW Reserved for Nordic hardware design

4.5.1.23 NRFHW[9]
Address offset: 0x074
Reserved for Nordic hardware design

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW NRFHW Reserved for Nordic hardware design

4.5.1.24 NRFHW[10]
Address offset: 0x078
Reserved for Nordic hardware design

4413_417 v1.9 52
 Core components

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW NRFHW Reserved for Nordic hardware design

4.5.1.25 NRFHW[11]
Address offset: 0x07C
Reserved for Nordic hardware design

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW NRFHW Reserved for Nordic hardware design

4.5.1.26 CUSTOMER[0]
Address offset: 0x080
Reserved for customer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW CUSTOMER Reserved for customer

4.5.1.27 CUSTOMER[1]
Address offset: 0x084
Reserved for customer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW CUSTOMER Reserved for customer

4.5.1.28 CUSTOMER[2]
Address offset: 0x088
Reserved for customer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW CUSTOMER Reserved for customer

4413_417 v1.9 53
 Core components

4.5.1.29 CUSTOMER[3]
Address offset: 0x08C
Reserved for customer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW CUSTOMER Reserved for customer

4.5.1.30 CUSTOMER[4]
Address offset: 0x090
Reserved for customer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW CUSTOMER Reserved for customer

4.5.1.31 CUSTOMER[5]
Address offset: 0x094
Reserved for customer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW CUSTOMER Reserved for customer

4.5.1.32 CUSTOMER[6]
Address offset: 0x098
Reserved for customer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW CUSTOMER Reserved for customer

4.5.1.33 CUSTOMER[7]
Address offset: 0x09C
Reserved for customer

4413_417 v1.9 54
 Core components

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW CUSTOMER Reserved for customer

4.5.1.34 CUSTOMER[8]
Address offset: 0x0A0
Reserved for customer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW CUSTOMER Reserved for customer

4.5.1.35 CUSTOMER[9]
Address offset: 0x0A4
Reserved for customer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW CUSTOMER Reserved for customer

4.5.1.36 CUSTOMER[10]
Address offset: 0x0A8
Reserved for customer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW CUSTOMER Reserved for customer

4.5.1.37 CUSTOMER[11]
Address offset: 0x0AC
Reserved for customer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW CUSTOMER Reserved for customer

4413_417 v1.9 55
 Core components

4.5.1.38 CUSTOMER[12]
Address offset: 0x0B0
Reserved for customer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW CUSTOMER Reserved for customer

4.5.1.39 CUSTOMER[13]
Address offset: 0x0B4
Reserved for customer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW CUSTOMER Reserved for customer

4.5.1.40 CUSTOMER[14]
Address offset: 0x0B8
Reserved for customer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW CUSTOMER Reserved for customer

4.5.1.41 CUSTOMER[15]
Address offset: 0x0BC
Reserved for customer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW CUSTOMER Reserved for customer

4.5.1.42 CUSTOMER[16]
Address offset: 0x0C0
Reserved for customer

4413_417 v1.9 56
 Core components

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW CUSTOMER Reserved for customer

4.5.1.43 CUSTOMER[17]
Address offset: 0x0C4
Reserved for customer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW CUSTOMER Reserved for customer

4.5.1.44 CUSTOMER[18]
Address offset: 0x0C8
Reserved for customer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW CUSTOMER Reserved for customer

4.5.1.45 CUSTOMER[19]
Address offset: 0x0CC
Reserved for customer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW CUSTOMER Reserved for customer

4.5.1.46 CUSTOMER[20]
Address offset: 0x0D0
Reserved for customer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW CUSTOMER Reserved for customer

4413_417 v1.9 57
 Core components

4.5.1.47 CUSTOMER[21]
Address offset: 0x0D4
Reserved for customer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW CUSTOMER Reserved for customer

4.5.1.48 CUSTOMER[22]
Address offset: 0x0D8
Reserved for customer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW CUSTOMER Reserved for customer

4.5.1.49 CUSTOMER[23]
Address offset: 0x0DC
Reserved for customer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW CUSTOMER Reserved for customer

4.5.1.50 CUSTOMER[24]
Address offset: 0x0E0
Reserved for customer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW CUSTOMER Reserved for customer

4.5.1.51 CUSTOMER[25]
Address offset: 0x0E4
Reserved for customer

4413_417 v1.9 58
 Core components

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW CUSTOMER Reserved for customer

4.5.1.52 CUSTOMER[26]
Address offset: 0x0E8
Reserved for customer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW CUSTOMER Reserved for customer

4.5.1.53 CUSTOMER[27]
Address offset: 0x0EC
Reserved for customer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW CUSTOMER Reserved for customer

4.5.1.54 CUSTOMER[28]
Address offset: 0x0F0
Reserved for customer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW CUSTOMER Reserved for customer

4.5.1.55 CUSTOMER[29]
Address offset: 0x0F4
Reserved for customer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW CUSTOMER Reserved for customer

4413_417 v1.9 59
 Core components

4.5.1.56 CUSTOMER[30]
Address offset: 0x0F8
Reserved for customer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW CUSTOMER Reserved for customer

4.5.1.57 CUSTOMER[31]
Address offset: 0x0FC
Reserved for customer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW CUSTOMER Reserved for customer

4.5.1.58 PSELRESET[0]
Address offset: 0x200
Mapping of the nRESET function (see POWER chapter for details)

Note: All PSELRESET registers have to contain the same value for a pin mapping to be valid. If
values are not the same, there will be no nRESET function exposed on a GPIO. As a result, the
device will always start independently of the levels present on any of the GPIOs.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN 18 GPIO pin number onto which nRESET is exposed
B RW PORT 0 Port number onto which nRESET is exposed
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

4.5.1.59 PSELRESET[1]
Address offset: 0x204
Mapping of the nRESET function (see POWER chapter for details)

Note: All PSELRESET registers have to contain the same value for a pin mapping to be valid. If
values are not the same, there will be no nRESET function exposed on a GPIO. As a result, the
device will always start independently of the levels present on any of the GPIOs.

4413_417 v1.9 60
 Core components

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN 18 GPIO pin number onto which nRESET is exposed
B RW PORT 0 Port number onto which nRESET is exposed
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

4.5.1.60 APPROTECT
Address offset: 0x208
Access port protection

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PALL Enable or disable access port protection.

See Debug and trace on page 66 for more information.

Disabled 0xFF Hardware disable of access port protection for devices where access port
protection is controlled by hardware
HwDisabled 0x5A Hardware disable of access port protection for devices where access port
protection is controlled by hardware and software
Enabled 0x00 Enable

4.5.1.61 NFCPINS
Address offset: 0x20C
Setting of pins dedicated to NFC functionality: NFC antenna or GPIO

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PROTECT Setting of pins dedicated to NFC functionality
Disabled 0 Operation as GPIO pins. Same protection as normal GPIO pins.
NFC 1 Operation as NFC antenna pins. Configures the protection for NFC
operation.

4.5.1.62 DEBUGCTRL
Address offset: 0x210
Processor debug control

4413_417 v1.9 61
 Core components

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B B B B B B B B A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW CPUNIDEN Configure CPU non-intrusive debug features
Enabled 0xFF Enable CPU ITM and ETM functionality (default behavior)
Disabled 0x00 Disable CPU ITM and ETM functionality
B RW CPUFPBEN Configure CPU flash patch and breakpoint (FPB) unit behavior
Enabled 0xFF Enable CPU FPB unit (default behavior)
Disabled 0x00 Disable CPU FPB unit. Writes into the FPB registers will be ignored.

4.5.1.63 REGOUT0
Address offset: 0x304
Output voltage from REG0 regulator stage. The maximum output voltage from this stage is given as VDDH -
V_VDDH-VDD.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW VOUT Output voltage from REG0 regulator stage.
1V8 0 1.8 V
2V1 1 2.1 V
2V4 2 2.4 V
2V7 3 2.7 V
3V0 4 3.0 V
3V3 5 3.3 V
DEFAULT 7 Default voltage: 1.8 V

4.6 EasyDMA
EasyDMA is a module implemented by some peripherals to gain direct access to Data RAM.
EasyDMA is an AHB bus master similar to CPU and is connected to the AHB multilayer interconnect for
direct access to Data RAM. EasyDMA is not able to access flash.
A peripheral can implement multiple EasyDMA instances to provide dedicated channels. For example,
for reading and writing of data between the peripheral and RAM. This concept is illustrated in EasyDMA
example on page 63.

4413_417 v1.9 62
 Core components

AHB multilayer Peripheral

RAM

READER
AHB
RAM EasyDMA

Peripheral
core
WRITER
RAM
AHB
EasyDMA

Figure 4: EasyDMA example

An EasyDMA channel is implemented in the following way, but some variations may occur:

READERBUFFER_SIZE 5
WRITERBUFFER_SIZE 6

uint8_t readerBuffer[READERBUFFER_SIZE] __at__ 0x20000000;

uint8_t writerBuffer[WRITERBUFFER_SIZE] __at__ 0x20000005;

// Configuring the READER channel

MYPERIPHERAL->READER.MAXCNT = READERBUFFER_SIZE;
MYPERIPHERAL->READER.PTR = &readerBuffer;

// Configure the WRITER channel

MYPERIPHERAL->WRITER.MAXCNT = WRITEERBUFFER_SIZE;
MYPERIPHERAL->WRITER.PTR = &writerBuffer;

This example shows a peripheral called MYPERIPHERAL that implements two EasyDMA channels - one for
reading called READER, and one for writing called WRITER. When the peripheral is started, it is assumed
that the peripheral will perform the following tasks:
• Read 5 bytes from the readerBuffer located in RAM at address 0x20000000
• Process the data
• Write no more than 6 bytes back to the writerBuffer located in RAM at address 0x20000005
The memory layout of these buffers is illustrated in EasyDMA memory layout on page 63.

0x20000000 readerBuffer[0] readerBuffer[1] readerBuffer[2] readerBuffer[3]

0x20000004 readerBuffer[4] writerBuffer[0] writerBuffer[1] writerBuffer[2]
0x20000008 writerBuffer[3] writerBuffer[4] writerBuffer[5]

Figure 5: EasyDMA memory layout

The WRITER.MAXCNT register should not be specified larger than the actual size of the buffer
(writerBuffer). Otherwise, the channel would overflow the writerBuffer.

4413_417 v1.9 63
 Core components

Once an EasyDMA transfer is completed, the AMOUNT register can be read by the CPU to see how many
bytes were transferred. For example, CPU can read MYPERIPHERAL->WRITER.AMOUNT register to see how
many bytes WRITER wrote to RAM.

Note: The PTR register of a READER or WRITER must point to a valid memory region before use.
The reset value of a PTR register is not guaranteed to point to valid memory. See Memory on page
21 for more information about the different memory regions and EasyDMA connectivity.

4.6.1 EasyDMA error handling

Some errors may occur during DMA handling.
If READER.PTR or WRITER.PTR is not pointing to a valid memory region, an EasyDMA transfer may result
in a HardFault or RAM corruption. See Memory on page 21 for more information about the different
memory regions.
If several AHB bus masters try to access the same AHB slave at the same time, AHB bus congestion might
occur. An EasyDMA channel is an AHB master. Depending on the peripheral, the peripheral may either stall
and wait for access to be granted, or lose data.

4.6.2 EasyDMA array list

EasyDMA is able to operate in Array List mode.
The Array List mode is implemented in channels where the LIST register is available.
The array list does not provide a mechanism to explicitly specify where the next item in the list is located.
Instead, it assumes that the list is organized as a linear array where items are located one after the other
in RAM.
The EasyDMA Array List can be implemented by using the data structure ArrayList_type as illustrated in
the code example below using a READER EasyDMA channel as an example:

#define BUFFER_SIZE 4

typedef struct ArrayList

{
uint8_t buffer[BUFFER_SIZE];
} ArrayList_type;

ArrayList_type ReaderList[3] __at__ 0x20000000;

MYPERIPHERAL->READER.MAXCNT = BUFFER_SIZE;
MYPERIPHERAL->READER.PTR = &ReaderList;
MYPERIPHERAL->READER.LIST = MYPERIPHERAL_READER_LIST_ArrayList;

The data structure only includes a buffer with size equal to the size of READER.MAXCNT register. EasyDMA
uses the READER.MAXCNT register to determine when the buffer is full.

4413_417 v1.9 64
 Core components

READER.PTR = &ReaderList

0x20000000 : ReaderList[0] buffer[0] buffer[1] buffer[2] buffer[3]

0x20000004 : ReaderList[1] buffer[0] buffer[1] buffer[2] buffer[3]
0x20000008 : ReaderList[2] buffer[0] buffer[1] buffer[2] buffer[3]

Figure 6: EasyDMA array list

4.7 AHB multilayer

AHB multilayer enables parallel access paths between multiple masters and slaves in a system. Access is
resolved using priorities.
Each bus master is connected to all the slave devices using an interconnection matrix. The bus masters are
assigned priorities, which are used to resolve access when two (or more) bus masters request access to
the same slave device. When that occurs, the following rules apply:
• If two (or more) bus masters request access to the same slave device, the master with the highest
priority is granted the access first.
• Bus masters with lower priority are stalled until the higher priority master has completed its
transaction.
• If the higher priority master pauses at any point during its transaction, the lower priority master in
queue is temporarily granted access to the slave device until the higher priority master resumes its
activity.
• Bus masters that have the same priority are mutually exclusive, thus cannot be used concurrently.
Some peripherals, such as RADIO, do not have a safe stalling mechanism (no internal data buffering, or
opportunity to pause incoming data). Being a low priority bus master might cause loss of data for such
peripherals upon bus contention. To avoid AHB bus contention when using multiple bus masters, follow
these guidelines:
• Avoid situations where more than one bus master is accessing the same slave.
• If more than one bus master is accessing the same slave, make sure that the bus bandwidth is not
exhausted.
Below is a list of bus masters in the system and their priorities.

4413_417 v1.9 65
 Core components

Bus master name Description

CPU
CTRL-AP
USB
CRYPTOCELL
SPIM1/SPIS1/TWIM1/TWIS1 Same priority and mutually exclusive
RADIO
CCM/ECB/AAR Same priority and mutually exclusive
SAADC
UARTE0
SPIM0/SPIS0/TWIM0/TWIS0 Same priority and mutually exclusive
SPIM2/SPIS2 Same priority and mutually exclusive
NFCT
I2S
PDM
PWM0
PWM1
PWM2
QSPI
PWM3
UARTE1
SPIM3

Table 5: AHB bus masters (listed from highest to lowest priority)

Defined bus masters are the CPU and peripherals with implemented EasyDMA. The available slaves are
RAM AHB slaves. How the bus masters and slaves are connected using the interconnection matrix is
illustrated in Memory on page 21.

4.8 Debug and trace

The debug and trace system offers a flexible and powerful mechanism for non-intrusive debugging.

DAP

SWDCLK
CTRL-AP
NVMC
External
SW-DP
debugger Access Port Protection Enable UICR
SWDIO &
DAP bus
interconnect

APPROTECT
AHB-AP

AHB RAM & flash

CxxxPWRUPREQ
Power CPU
POWER
CxxxPWRUPRACK
ARM Cortex-M4

TRACECLK
APB/AHB
Trace Peripherals
TRACEDATA[0] / SWO ETM

TRACEDATA[1]
TPIU
TRACEDATA[2]

TRACEDATA[3] Trace
ITM

Figure 7: Debug and trace overview

The main features of the debug and trace system are the following:
• Two-pin serial wire debug (SWD) interface

4413_417 v1.9 66
 Core components

• Flash patch and breakpoint (FPB) unit that supports the following comparators:
• Two literal comparators
• Six instruction comparators
• Data watchpoint and trace (DWT) unit with four comparators
• Instrumentation trace macrocell (ITM)
• Embedded trace macrocell (ETM)
• Trace port interface unit (TPIU)
• 4-bit parallel trace of ITM and ETM trace data
• Serial wire output (SWO) trace of ITM data

4.8.1 DAP - Debug access port

An external debugger can access the device via the DAP.
The debug access port (DAP) implements a standard ARM CoreSight serial wire debug port (SW-DP), which
implements the serial wire debug protocol (SWD). SWD is a two-pin serial interface, see SWDCLK and
SWDIO in Debug and trace overview on page 66.
In addition to the default access port in CPU (AHB-AP), the DAP includes a custom control access port
(CTRL-AP). The CTRL-AP is described in more detail in CTRL-AP - Control access port on page 70.

Note:
• The SWDIO line has an internal pull-up resistor.
• The SWDCLK line has an internal pull-down resistor.

4.8.2 Access port protection

Access port protection blocks the debugger from read and write access to all CPU registers and memory-
mapped addresses when enabled.
Access port protection is enabled and disabled differently depending on the build code of the device.

Access port protection controlled by hardware

This information refers to build codes Dxx and earlier.
By default, access port protection is disabled.
Access port protection is enabled by writing UICR.APPROTECT to Enabled and performing any reset. See
Reset on page 88 for more information.
Access port protection is disabled by issuing an ERASEALL command via CTRL-AP. This command will erase
the flash, UICR, and RAM, including UICR.APPROTECT. Erasing UICR will set UICR.APPROTECT value to
Disabled. CTRL-AP is described in more detail in CTRL-AP - Control access port on page 70.

Access port protection controlled by hardware and software

This information refers to build codes Fxx and later.
By default, access port protection is enabled.
Access port protection is disabled by issuing an ERASEALL command via CTRL-AP. Read CTRL-
AP.APPROTECTSTATUS to ensure that access port protection is disabled, and repeat the ERASEALL
command if needed. This command will erase the flash, UICR, and RAM. CTRL-AP is described in more
detail in CTRL-AP - Control access port on page 70. Access port protection will remain disabled until
one of the following occurs:

4413_417 v1.9 67
 Core components

• Pin reset
• Power or brownout reset
• Watchdog reset if not in Debug Interface Mode, see Debug Interface mode on page 72
• Wake from System OFF if not in Emulated System OFF
To keep access port protection disabled, the following actions must be performed:
• Program UICR.APPROTECT to HwDisabled. This disables the hardware part of the access port
protection scheme after the first reset of any type. The hardware part of the access port protection will
stay disabled as long as UICR.APPROTECT is not overwritten.
• Firmware must write APPROTECT.DISABLE to SwDisable. This disables the software part of the
access port protection scheme.

Note: Register APPROTECT.DISABLE is reset after pin reset, power or brownout reset, watchdog
reset, or wake from System OFF as mentioned above.

The following figure is an example on how a device with access port protection enabled can be erased,
programmed, and configured to allow debugging. Operations sent from debugger as well as registers
written by firmware will affect the access port state.
Debugger
W PRO isab
AP w D
rit TE le
Pr mw
CT ASE

Pi
e
og ar
ER
RL AL

fir

n
UI CT
ra e
-A L

re
CR =
m

se
P

t
d

Closed Open Closed Open Access port state

Write APPROTECT.DISABLE =
SwDisable
Firmware

Figure 8: Access port unlocking

Access port protection is enabled when the disabling conditions are not present. For additional security,
it is recommended to write Enabled to UICR.APPROTECT, and have firmware write Force to
APPROTECT.FORCEPROTECT. This is illustrated in the following figure.

Note: Register APPROTECT.FORCEPROTECT is reset after any reset.

4413_417 v1.9 68
 Core components

Debugger

W PRO ble
AP En
rit TE d
Pr mw
C T A SE

Pi
e
og ar
ER
RL AL

fir

n
UI CT
ra e
-A L

re
CR =
m

se
P

t
Closed Open Closed Access port state

Write APPROTECT.FORCEPROTECT =
Force
Firmware

Figure 9: Force access port protection

4.8.2.1 Registers

Instances

Instance Base address Description

APPROTECT 0x40000000 APPROTECT control

Register overview

Register Offset Description

FORCEPROTECT 0x550 Software force enable APPROTECT mechanism until next reset.
DISABLE 0x558 Software disable APPROTECT mechanism

4.8.2.1.1 FORCEPROTECT
Address offset: 0x550
Software force enable APPROTECT mechanism until next reset.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW1 FORCEPROTECT Write 0x0 to force enable APPROTECT mechanism
Force 0x0 Software force enable APPROTECT mechanism

4.8.2.1.2 DISABLE
Address offset: 0x558
Software disable APPROTECT mechanism

4413_417 v1.9 69
 Core components

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW DISABLE Software disable APPROTECT mechanism
SwDisable 0x5A Software disable APPROTECT mechanism

4.8.3 CTRL-AP - Control access port

The control access port (CTRL-AP) is a custom access port that enables control of the device when other
access ports in the DAP are disabled by the access port protection.
Access port protection is described in more detail in Access port protection on page 67.
Control access port has the following features:
• Soft reset - see Reset on page 88 for more information
• Disabling of access port protection - device control is allowed through CTRL-AP even when all other
access ports in DAP are disabled by access port protection

4.8.3.1 Registers

Register overview

Register Offset Description

RESET 0x000 Soft reset triggered through CTRL-AP
ERASEALL 0x004 Erase all
ERASEALLSTATUS 0x008 Status register for the ERASEALL operation
APPROTECTSTATUS 0x00C Status register for access port protection
IDR 0x0FC CTRL-AP identification register, IDR

4.8.3.1.1 RESET
Address offset: 0x000
Soft reset triggered through CTRL-AP

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW RESET Soft reset triggered through CTRL-AP. See Reset behavior in POWER chapter
for more details.
NoReset 0 Reset is not active
Reset 1 Reset is active. Device is held in reset.

4.8.3.1.2 ERASEALL
Address offset: 0x004
Erase all

4413_417 v1.9 70
 Core components

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W ERASEALL Erase all flash and RAM
NoOperation 0 No operation
Erase 1 Erase all flash and RAM

4.8.3.1.3 ERASEALLSTATUS
Address offset: 0x008
Status register for the ERASEALL operation

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R ERASEALLSTATUS Status register for the ERASEALL operation
Ready 0 ERASEALL is ready
Busy 1 ERASEALL is busy (on-going)

4.8.3.1.4 APPROTECTSTATUS
Address offset: 0x00C
Status register for access port protection

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R APPROTECTSTATUS Status register for access port protection
Enabled 0 Access port protection enabled
Disabled 1 Access port protection not enabled

4.8.3.1.5 IDR
Address offset: 0x0FC
CTRL-AP identification register, IDR

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E E E D D D D C C C C C C C B B B B A A A A A A A A

Reset 0x02880000 0 0 0 0 0 0 1 0 1 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R APID AP identification
B R CLASS Access port (AP) class
NotDefined 0x0 No defined class
MEMAP 0x8 Memory access port
C R JEP106ID JEDEC JEP106 identity code
D R JEP106CONT JEDEC JEP106 continuation code
E R REVISION Revision

4413_417 v1.9 71
 Core components

4.8.3.2 Electrical specification

4.8.3.2.1 Control access port

Symbol Description Min. Typ. Max. Units

Rpull Internal SWDIO and SWDCLK pull up/down resistance 13 kΩ
fSWDCLK SWDCLK frequency 0.125 8 MHz

4.8.4 Debug Interface mode

Before an external debugger can access either CPU's access port (AHB-AP) or the control access port
(CTRL-AP), the debugger must first request the device to power up via CxxxPWRUPREQ in the SWJ-DP.
If the device is in System OFF when power is requested via CxxxPWRUPREQ, the system will wake up and
the DIF flag in RESETREAS on page 94 will be set. The device is in the Debug Interface mode as long
as the debugger is requesting power via CxxxPWRUPREQ. Once the debugger stops requesting power
via CxxxPWRUPREQ, the device is back in normal mode. Some peripherals behave differently in Debug
Interface mode compared to normal mode. These differences are described in more detail in the chapters
of the peripherals that are affected.
When a debug session is over, the external debugger must make sure to put the device back into normal
mode since the overall power consumption is higher in Debug Interface mode than in normal mode.
For details on how to use the debug capabilities, read the debug documentation of your IDE.

4.8.5 Real-time debug

The nRF52840 supports real-time debugging.
Real-time debugging allows interrupts to execute to completion in real time when breakpoints are set
in Thread mode or lower priority interrupts. This enables developers to set breakpoints and single-step
through the code without the risk of real-time event-driven threads running at higher priority failing.
For example, this enables the device to continue to service the high-priority interrupts of an external
controller or sensor without failure or loss of state synchronization while the developer steps through
code in a low-priority thread.

4.8.6 Trace
The device supports ETM and ITM trace.
Trace data from the ETM and the ITM is sent to an external debugger via a 4-bit wide parallel trace
port interface unit (TPIU), see TRACEDATA[0] through TRACEDATA[3] and TRACECLK in Debug and trace
overview on page 66.
In addition to parallel trace, the TPIU supports serial trace via the serial wire output (SWO) trace protocol.
Parallel and serial trace cannot be used at the same time. ETM trace is only supported in Parallel Trace
mode, while ITM trace is supported in both Parallel and Serial Trace modes.
For details on how to use the trace capabilities, read the debug documentation of your IDE.
TPIU's trace pins are multiplexed with GPIOs. SWO and TRACEDATA[0] use the same GPIO. See Pin
assignments on page 845 for more information.
Trace speed is configured in register TRACECONFIG on page 169. The speed of the trace pins depends
on the DRIVE setting of the GPIOs that the trace pins are multiplexed with. Only S0S1 and H0H1 drives are
suitable for debugging. S0S1 is the default DRIVE setting at reset. If parallel or serial trace port signals are
not fast enough with the default settings, all GPIOs in use for tracing should be set to high drive (H0H1).
The DRIVE setting for these GPIOs should not be overwritten by firmware during the debugging session.

4413_417 v1.9 72
 Core components

4.8.6.1 Registers
4.8.6.2 Electrical specification
4.8.6.2.1 Trace port

Symbol Description Min. Typ. Max. Units

Tcyc Clock period as defined by Arm in the Timing specifications for Trace Port 62.5 500 ns
Physical Interface of the Embedded Trace Macrocell Architecture Specification

4413_417 v1.9 73
5 Power and clock management

5.1 Power management unit (PMU)

Power and clock management in nRF52840 is designed to automatically ensure maximum power
efficiency.
The core of the power and clock management system is the power management unit (PMU) illustrated in
the following figure.
MCU

CPU

External Internal
power sources voltage
regulators

PMU
Memory

External Internal
crystals oscillators Peripheral

Figure 10: Power management unit

The PMU automatically detects which power and clock resources are required by the different system
components at any given time. The PMU will then automatically start/stop and choose operation modes in
supply regulators and clock sources, to achieve the lowest power consumption possible.

5.2 Current consumption

Because the system is continually being tuned by the Power management unit (PMU) on page 74,
estimating an application's current consumption can be challenging when measurements cannot be
directly performed on the hardware. To facilitate the estimation process, a set of current consumption
scenarios are provided to show the typical current drawn from the VDD supply.
Each scenario specifies a set of operations and conditions applying to the given scenario. The following
table shows a set of common conditions used in all scenarios, unless otherwise stated in the description of
a given scenario. All scenarios are listed in Electrical specification on page 75.

4413_417 v1.9 74
 Power and clock management

Condition Value
Supply 3 V on VDD/VDDH (Normal voltage mode)
Temperature 25°C
CPU WFI (wait for interrupt)/WFE (wait for event) sleep
Peripherals All idle
Clock Not running
Regulator LDO
RAM In System ON, full 256 kB powered. In System OFF, full 256 kB retention.
Compiler GCC v4.9.3 20150529 (arm-none-eabi-gcc).
• Compiler flags: -O0 -falign-functions=16 -fno-strict-
aliasing -mcpu=cortex-m4 -mfloat-abi=soft -msoft-
float -mthumb.

Cache enabled2 Yes

32 MHz crystal3 SMD 2520, 32 MHz, 10 pF +/- 10 ppm

Table 6: Current consumption scenarios, common conditions

5.2.1 Electrical specification

5.2.1.1 Sleep

Symbol Description Min. Typ. Max. Units

ION_RAMOFF_EVENT System ON, no RAM retention, wake on any event 0.97 µA
ION_RAMON_EVENT System ON, full 256 kB RAM retention, wake on any event 2.35 µA
ION_RAMON_POF System ON, full 256 kB RAM retention, wake on any event, power-fail 2.35 µA
comparator enabled
ION_RAMON_GPIOTE System ON, full 256 kB RAM retention, wake on GPIOTE input (event mode) 17.37 µA
ION_RAMON_GPIOTEPORT System ON, full 256 kB RAM retention, wake on GPIOTE PORT event 2.36 µA
ION_RAMOFF_RTC System ON, no RAM retention, wake on RTC (running from LFRC clock) 1.50 µA
ION_RAMON_RTC System ON, full 256 kB RAM retention, wake on RTC (running from LFRC 3.16 µA
clock)
IOFF_RAMOFF_RESET System OFF, no RAM retention, wake on reset 0.40 µA
IOFF_RAMOFF_LPCOMP System OFF, no RAM retention, wake on LPCOMP 0.86 µA
IOFF_RAMON_RESET System OFF, full 256 kB RAM retention, wake on reset 1.86 µA
ION_RAMOFF_EVENT_5V System ON, no RAM retention, wake on any event, 5 V supply on VDDH, REG0 1.29 µA
output = 3.3 V
IOFF_RAMOFF_RESET_5V System OFF, no RAM retention, wake on reset, 5 V supply on VDDH, REG0 0.95 µA
output = 3.3 V

2
Applies only when CPU is running from flash memory
3
Applies only when HFXO is running

4413_417 v1.9 75
 Power and clock management

3.5

3
Current consumption [µA]

2.5

1.5

0.5

0
-40 -20 0 20 40 60 80 100

Temperature Range [ºC]

1.7 V 3V 3.6 V

Figure 11: System OFF, no RAM retention, wake on reset (typical values)

12

10
Current consumption [µA]

0
-40 -20 0 20 40 60 80 100

Temperature Range [ºC]

1.7 V 3V 3.6 V

Figure 12: System ON, no RAM retention, wake on any event (typical values)

4413_417 v1.9 76
 Power and clock management

5.2.1.2 COMP active

Symbol Description Min. Typ. Max. Units

ICOMP,LP COMP enabled, low power mode 30.1 µA
ICOMP,NORM COMP enabled, normal mode 31.8 µA
ICOMP,HS COMP enabled, high-speed mode 35.1 µA

5.2.1.3 CPU running

Symbol Description Min. Typ. Max. Units

ICPU0 CPU running CoreMark @64 MHz from flash, Clock = HFXO, Regulator = DC/ 3.3 mA
DC
ICPU1 CPU running CoreMark @64 MHz from flash, Clock = HFXO 6.3 mA
ICPU2 CPU running CoreMark @64 MHz from RAM, Clock = HFXO, Regulator = DC/ 2.8 mA
DC
ICPU3 CPU running CoreMark @64 MHz from RAM, Clock = HFXO 5.2 mA
ICPU4 CPU running CoreMark @64 MHz from flash, Clock = HFINT, Regulator = DC/ 3.1 mA
DC

5.2.1.4 NFCT active

Symbol Description Min. Typ. Max. Units

Isense Current in SENSE STATE 4 100 nA

Iactivated Current in ACTIVATED STATE 400 µA

5.2.1.5 Radio transmitting/receiving

Symbol Description Min. Typ. Max. Units

IRADIO_TX0 Radio transmitting @ 8 dBm output power, 1 Mbps Bluetooth Low Energy 16.40 mA
(BLE) mode, Clock = HFXO, Regulator = DC/DC
IRADIO_TX1 Radio transmitting @ 0 dBm output power, 1 Mbps BLE mode, Clock = HFXO, 6.40 mA
Regulator = DC/DC
IRADIO_TX2 Radio transmitting @ -40 dBm output power, 1 Mbps BLE mode, Clock = 3.83 mA
HFXO, Regulator = DC/DC
IRADIO_TX3 Radio transmitting @ 0 dBm output power, 1 Mbps BLE mode, Clock = HFXO 10.80 mA
IRADIO_TX4 Radio transmitting @ -40 dBm output power, 1 Mbps BLE mode, Clock = HFXO 4.82 mA
IRADIO_TX5 Radio transmitting @ 0 dBm output power, 250 kbit/s IEE 802.15.4-2006 6.40 mA
mode, Clock = HFXO, Regulator = DC/DC
IRADIO_RX0 Radio receiving @ 1 Mbps BLE mode, Clock = HFXO, Regulator = DC/DC 6.26 mA
IRADIO_RX1 Radio receiving @ 1 Mbps BLE mode, Clock = HFXO 10.10 mA
IRADIO_RX2 Radio receiving @ 250 kbit/s IEE 802.15.4-2006 mode, Clock = HFXO, 6.53 mA
Regulator = DC/DC

4
This current does not apply when in NFC field

4413_417 v1.9 77
 Power and clock management

28

26

24
Current consumption [mA]

22

20

18

16

14

12
1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6

Supply voltage [V]

-40 ºC 25 ºC 85 ºC

Figure 13: Radio transmitting @ 8 dBm output power, 1 Mbps

BLE mode, Clock = HFXO, Regulator = DC/DC (typical values)

10

9.5

8.5
Current consumption [mA]

7.5

6.5

5.5

5
1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6

Supply voltage [V]

-40 ºC 25 ºC 85 ºC

Figure 14: Radio transmitting @ 0 dBm output power, 1 Mbps

BLE mode, Clock = HFXO, Regulator = DC/DC (typical values)

4413_417 v1.9 78
 Power and clock management

5.2.1.6 RNG active

Symbol Description Min. Typ. Max. Units

IRNG0 RNG running 635 µA

5.2.1.7 SAADC active

Symbol Description Min. Typ. Max. Units

ISAADC,RUN SAADC sampling @ 16 ksps, Acquisition time = 20 µs, Clock = HFXO, Regulator 1.24 mA
= DC/DC

5.2.1.8 TEMP active

Symbol Description Min. Typ. Max. Units

ITEMP0 TEMP started 1.05 mA

5.2.1.9 TIMER running

Symbol Description Min. Typ. Max. Units

ITIMER0 One TIMER instance running @ 1 MHz, Clock = HFINT 418 µA
ITIMER1 Two TIMER instances running @ 1 MHz, Clock = HFINT 418 µA
ITIMER2 One TIMER instance running @ 1 MHz, Clock = HFXO 646 µA
ITIMER3 One TIMER instance running @ 16 MHz, Clock = HFINT 595 µA
ITIMER4 One TIMER instance running @ 16 MHz, Clock = HFXO 823 µA

5.2.1.10 USBD running

Symbol Description Min. Typ. Max. Units

IUSB,ACTIVE,VBUS Current from VBUS supply, USB active 2.4 mA
IUSB,SUSPEND,VBUS Current from VBUS supply, USB suspended, CPU sleeping 262 µA
IUSB,ACTIVE,VDD Current from VDD supply (normal voltage mode), all RAM retained, 7.73 mA
regulator=LDO, CPU running, USB active
IUSB,SUSPEND,VDD Current from VDD supply (normal voltage mode), all RAM retained, 173 µA
regulator=LDO, CPU sleeping, USB suspended
IUSB,ACTIVE,VDDH Current from VDDH supply (high voltage mode), VDD=3 V (REG0 output), all 7.46 mA
RAM retained, regulator=LDO, CPU running, USB active
IUSB,SUSPEND,VDDH Current from VDDH supply (high voltage mode), VDD=3 V (REG0 output), all 178 µA
RAM retained, regulator=LDO, CPU sleeping, USB suspended
IUSB,DISABLED,VDD Current from VDD supply, USB disabled, VBUS supply connected, all RAM 7 µA
retained, regulator=LDO, CPU sleeping

5.2.1.11 WDT active

Symbol Description Min. Typ. Max. Units

IWDT,STARTED WDT started 3.1 µA

4413_417 v1.9 79
 Power and clock management

5.2.1.12 Compounded

Symbol Description Min. Typ. Max. Units

IS0 CPU running CoreMark from flash, Radio transmitting @ 0 dBm output power, 8.1 mA
1 Mbps Bluetooth Low Energy (BLE) mode, Clock = HFXO, Regulator = DC/DC
IS1 CPU running CoreMark from flash, Radio receiving @ 1 Mbps BLE mode, 8.6 mA
Clock = HFXO, Regulator = DC/DC
IS2 CPU running CoreMark from flash, Radio transmitting @ 0 dBm output power, 15.4 mA
1 Mbps BLE mode, Clock = HFXO
IS3 CPU running CoreMark from flash, Radio receiving @ 1 Mbps BLE mode, 16.2 mA
Clock = HFXO
IS4 CPU running CoreMark from flash, Radio transmitting @ 0 dBm output power, 11.9 mA
1 Mbps BLE mode, Clock = HFXO, Regulator = DC/DC, 5 V supply on VDDH,
REG0 output = 3.3 V
IS5 CPU running CoreMark from flash, Radio receiving @ 1 Mbps BLE mode, 12.7 mA
Clock = HFXO, Regulator = DC/DC, 5 V supply on VDDH, REG0 output = 3.3 V

5.3 POWER — Power supply

The power supply consists of a number of LDO and DC/DC regulators that are utilized to maximize the
system's power efficiency.
This device has the following power supply features:
• On-chip LDO and DC/DC regulators
• Global System ON/OFF modes
• Individual RAM section power control for all system modes
• Analog or digital pin wakeup from System OFF
• Supervisor hardware to manage power-on reset, brownout, and power failure
• Auto-controlled refresh modes for LDO and DC/DC regulators to maximize efficiency
• External circuitry supply
• Separate USB supply

5.3.1 Main supply

The main supply voltage is connected to the VDD/VDDH pins. The system will enter one of two supply
voltage modes, Normal or High Voltage mode, depending on how the supply voltage is connected to these
pins.

Note: VDD and VDDH are shortcircuited inside the QFN48 package. Therefore the QFN48 device is
only usable in Normal Voltage supply mode, and not High Voltage supply mode.

The system enters Normal Voltage mode when the supply voltage is connected to both the VDD and VDDH
pins (pin VDD shorted to pin VDDH). For the supply voltage range to connect to both VDD and VDDH pins,
see parameter VDD.
The system enters High Voltage mode when the supply voltage is only connected to the VDDH pin and the
VDD pin is not connected to any voltage supply. For the supply voltage range to connect to the VDDH pin,
see parameter VDDH.
The register MAINREGSTATUS on page 98 can be used to read the current supply voltage mode.

5.3.1.1 Main voltage regulators

The system contains two main supply regulator stages, REG0 and REG1.

4413_417 v1.9 80
 Power and clock management

Each regulator stage has the following regulator type options:

• Low-dropout regulator (LDO)
• Buck regulator (DC/DC)
In Normal Voltage mode, only the REG1 regulator stage is used, and the REG0 stage is automatically
disabled. In High Voltage mode, both regulator stages (REG0 and REG1) are used. The output voltage of
REG0 can be configured in register REGOUT0 on page 62. This output voltage is connected to VDD and is
the input voltage to REG1.

Note: In High Voltage mode, the configured output voltage for REG0 (REGOUT0 on page 62) must
not be greater than REG0 input voltage minus the voltage drop in REG0 (VDDH - VVDDH-VDD).

By default, the LDO regulators are enabled and the DC/DC regulators are disabled. Registers DCDCEN0
on page 98 and DCDCEN on page 97 are used to enable the DC/DC regulators for REG0 and REG1
stages respectively.
When a DC/DC converter is enabled, the corresponding LDO regulator is disabled. External LC filters must
be connected for each of the DC/DC regulators if they are being used. The advantage of using a DC/DC
regulator is that the overall power consumption is normally reduced as the efficiency of such a regulator
is higher than that of a LDO. The efficiency gained by using a DC/DC regulator is best seen when the
regulator voltage drop (difference between input and output voltage) is high. The efficiency of internal
regulators vary with the supply voltage and the current drawn from the regulators.

Note: Do not enable the DC/DC regulator without an external LC filter being connected as this will
inhibit device operation, including debug access, until an LC filter is connected.

5.3.1.2 GPIO levels

The GPIO high reference voltage is equal to the level on the VDD pin.
In Normal Voltage mode, the GPIO high level equals the voltage supplied to the VDD pin. In High Voltage
mode, it equals the level specified in register REGOUT0 on page 62.

5.3.1.3 External circuitry supply

In High Voltage mode, the output from REG0 can be used to supply external circuitry from the VDD pin.
The VDD output voltage is configured in the register REGOUT0 on page 62.
The supported output voltage range depends on the supply voltage provided by the VDDH pin. Minimum
difference between voltage supplied on the VDDH pin and the voltage output on the VDD pin is defined by
the VREG0,DROP parameter in Regulator specifications, REG0 stage on page 154.
Supplying external circuitry is allowed in both System OFF and System ON mode.

Note: The maximum allowed current drawn by external circuitry is dependent on the total internal
current draw. The maximum current that can be drawn externally from REG0 is defined in Regulator
specifications, REG0 stage on page 154).

5.3.1.4 Regulator configuration examples

The voltage regulators can be configured in several ways, depending on the selected supply voltage mode
(Normal/High) and the regulator type option (LDO or DC/DC).
Four configuration examples are illustrated in the following figures.

4413_417 v1.9 81
 Power and clock management

Main supply

DCDCEN0 REGOUT0 DCDCEN

REG0 REG1
Supply
LDO LDO
VDDH 1.3V System power

DC/DC DC/DC

DCCH VDD DCC DEC4 GND

Figure 15: Normal Voltage mode, LDO only

Main supply

DCDCEN0 REGOUT0 DCDCEN

REG0 REG1
Supply
LDO LDO
VDDH 1.3V System power

DC/DC DC/DC

DCCH VDD DCC DEC4 GND

Figure 16: Normal Voltage mode, DC/DC REG1 enabled

4413_417 v1.9 82
 Power and clock management

Main supply

DCDCEN0 REGOUT0 DCDCEN

REG0 REG1

Supply LDO LDO

VDDH 1.3V System power

DC/DC DC/DC

DCCH VDD DCC DEC4 GND

REGOUT0

Figure 17: High Voltage mode, LDO only

Main supply

DCDCEN0 REGOUT0 DCDCEN

REG0 REG1

Supply LDO LDO

VDDH 1.3V System power

DC/DC DC/DC

DCCH VDD DCC DEC4 GND

REGOUT0

Figure 18: High Voltage mode, DC/DC for REG0 and REG1 enabled

5.3.1.5 Power supply supervisor

The power supply supervisor enables monitoring of the connected power supply.
The power supply supervisor provides the following functionality:
• Power-on reset - signals the circuit when a supply is connected
• An optional power-fail comparator (POF) - signals the application when the supply voltages drop below
a configured threshold
• A fixed brownout reset detector - holds the system in reset when the voltage is too low for safe
operation
The power supply supervisor is illustrated in the following figure.

4413_417 v1.9 83
 Power and clock management

VDD Brownout reset

VBOR

Power-on reset

POFCON.POF
POFCON.THRESHOLDVDDH
(VDDH>VDD)

4.2 V VDDH
...........

MUX VPOFH
2.8 V

2.7 V
POFWARN

2.8 V VDD
...........

VPOF
MUX
1.8 V

1.7 V

POFCON.THRESHOLD POFCON.POF

Figure 19: Power supply supervisor

5.3.1.6 Power-fail comparator

Using the power-fail comparator (POF) is optional. When enabled, it can provide an early warning to the
CPU of an impending power supply failure.
To enable and configure the power-fail comparator, see the register POFCON on page 96.
When the supply voltage falls below the defined threshold, the power-fail comparator generates an event
(POFWARN) that can be used by an application to prepare for power failure. This event is also generated
when the supply voltage is already below the threshold at the time the power-fail comparator is enabled,
or if the threshold is re-configured to a level above the supply voltage.

4413_417 v1.9 84
 Power and clock management

If the power failure warning is enabled, and the supply voltage is below the threshold, the power-fail
comparator will prevent the NVMC from performing write operations to the flash.
The comparator features a hysteresis of VHYST, as illustrated in the following figure.

Supply (VDD or VDDH)

VPOF+VHYST
VPOF

1.7V

t
POFWARN

POFWARN
MCU

BOR

Figure 20: Power-fail comparator (BOR = brownout reset)

To save power, the power-fail comparator is not active in System OFF or System ON when HFCLK is not
running.

5.3.2 USB supply

When using the USB peripheral, a 5 V USB supply needs to be provided to the VBUS pin.
The USB peripheral has a dedicated internal voltage regulator for converting the VBUS supply to 3.3 V used
by the USB signalling interface (D+ and D- lines, and pull-up on D+). The remainder of the USB peripheral
(USBD) is supplied through the main supply like other on-chip features. As a consequence, VBUS and
either VDDH or VDD supplies are required for USB peripheral operation.
When VBUS rises into its valid range, the software is notified through a USBDETECTED event. A
USBREMOVED event is sent when VBUS goes below its valid range. Use these events to implement the
USBD start-up sequence described in the USBD chapter.
When VBUS rises into its valid range while the device is in System OFF, the device resets and transitions to
System ON mode. The RESETREAS register will have the VBUS bit set to indicate the source of the wake-up.
See VBUS detection specifications on page 156 for the levels at which the events are sent (VBUS,DETECT
and VBUS,REMOVE) or at which the system is woken up from System OFF (VBUS,DETECT).
When the USBD peripheral is enabled through the ENABLE register, and VBUS is detected, the regulator
is turned on. A USBPWRRDY event is sent when the regulator's worst case settling time has elapsed,
indicating to the software that it can enable the USB pull-up to signal a USB connection to the host.
The software can read the state of the VBUS detection and regulator output readiness at any time through
the USBREGSTATUS register.

4413_417 v1.9 85
 Power and clock management

USB supply

5 V USB
supply

VBUS 3.3 V USB power

LDO

DECUSB

Figure 21: USB voltage regulator

To ensure stability, the input and output of the USB regulator need to be decoupled with a suitable
decoupling capacitor. See Reference circuitry on page 856 for the recommended values.

5.3.3 System OFF mode

System OFF is the deepest power saving mode the system can enter. In this mode, the system’s core
functionality is powered down and all ongoing tasks are terminated.
The device can be put into System OFF mode using the register SYSTEMOFF on page 96. When in
System OFF mode, the device can be woken up through one of the following signals:
• The DETECT signal, optionally generated by the GPIO peripheral.
• The ANADETECT signal, optionally generated by the LPCOMP module.
• The SENSE signal, optionally generated by the NFC module to wake-on-field.
• Detecting a valid USB voltage on the VBUS pin (VBUS,DETECT).
• A reset.
The system is reset when it wakes up from System OFF mode.
One or more RAM sections can be retained in System OFF mode, depending on the settings in the
RAM[n].POWER registers. RAM[n].POWER are retained registers. These registers are usually overwritten
by the start-up code provided with the nRF application examples.
Before entering System OFF mode, all on-going EasyDMA transactions need to have completed.
See peripheral specific chapters for more information about how to acquire the status of EasyDMA
transactions.

5.3.3.1 Emulated System OFF mode

If the device is in Debug Interface mode, System OFF will be emulated to secure that all required resources
needed for debugging are available during System OFF.
Required resources needed for debugging include the following key components:

4413_417 v1.9 86
 Power and clock management

• Debug and trace on page 66

• CLOCK — Clock control on page 156
• POWER — Power supply on page 80
• NVMC — Non-volatile memory controller on page 25
• CPU on page 20
• Flash memory
• RAM
See Debug and trace on page 66 for more information.
Because the CPU is kept on in an emulated System OFF mode, it is recommended to add an infinite loop
directly after entering System OFF, to prevent the CPU from executing code that normally should not be
executed.

5.3.4 System ON mode

System ON is the default state after power-on reset. In System ON mode, all functional blocks such as the
CPU or peripherals can be in IDLE or RUN mode, depending on the configuration set by the software and
the state of the application executing.
Register RESETREAS on page 94 provides information about the source causing the wakeup or reset.
The system can switch the appropriate internal power sources on and off, depending on the amount of
power needed at any given time. The power requirement of a peripheral is directly related to its activity
level, and the activity level of a peripheral fluctuates when specific tasks are triggered or events are
generated.

5.3.4.1 Sub-power modes

In System ON mode, when the CPU and all peripherals are in IDLE mode, the system can reside in one of
the two sub-power modes.
The sub-power modes are:
• Constant Latency
• Low-power
In Constant Latency mode, the CPU wakeup latency and the PPI task response are constant and kept at
a minimum. This is secured by forcing a set of basic resources to be turned on while in sleep. The cost of
constant and predictable latency is increased power consumption. Constant Latency mode is selected by
triggering the CONSTLAT task.
In Low-power mode, the automatic power management system described in System ON mode on page
87 ensures that the most efficient supply option is chosen to save power. The cost of having the lowest
possible power consumption is a varying CPU wakeup latency and PPI task response. Low-power mode is
selected by triggering the LOWPWR task.
When the system enters System ON mode, it is by default in the sub-power mode Low-power.

5.3.5 RAM power control

The RAM power control registers are used for configuring the following:
• The RAM sections to be retained during System OFF
• The RAM sections to be retained and accessible during System ON
In System OFF, retention of a RAM section is configured in the RETENTION field of the corresponding
register RAM[n].POWER.
In System ON, retention and accessibility of a RAM section is configured in the RETENTION and POWER
fields of the corresponding register RAM[n].POWER.

4413_417 v1.9 87
 Power and clock management

The following table summarizes the behavior of these registers.

Configuration RAM section status

System on/off RAM[n].POWER.POWER RAM[n].POWER.RETENTION Accessible Retained

Off x Off No No
Off x On No Yes
On Off Off No No
On Off 5 On No Yes

On On x Yes Yes

Table 7: RAM section configuration

The advantage of not retaining RAM contents is that the overall current consumption is reduced.
See Memory on page 21 for more information on RAM sections.

5.3.6 Reset
Several sources may trigger a reset.
After a reset has occurred, register RESETREAS can be read to determine which source triggered the reset.

5.3.6.1 Power-on reset

The power-on reset generator initializes the system at power-on.
The system is held in reset state until the supply has reached the minimum operating voltage and the
internal voltage regulators have started.

5.3.6.2 Pin reset

A pin reset is generated when the physical reset pin on the device is asserted.
Pin reset is configured via both registers PSELRESET[n].

5.3.6.3 Wakeup from System OFF mode reset

The device is reset when it wakes up from System OFF mode.
The debug access port (DAP) is not reset following a wake up from System OFF mode if the device is in
Debug Interface mode. See chapter Debug and trace on page 66 for more information.

5.3.6.4 Soft reset

A soft reset is generated when the SYSRESETREQ bit of the application interrupt and reset control register
(AIRCR) in the ARM® core is set.
See ARM documentation for more details.
A soft reset can also be generated via the register RESET on page 70 in the CTRL-AP.

5.3.6.5 Watchdog reset

A Watchdog reset is generated when the watchdog times out.
See chapter WDT — Watchdog timer on page 837 for more information.

5
Not useful. RAM section power off gives negligible reduction in current consumption when retention
is on.

4413_417 v1.9 88
 Power and clock management

5.3.6.6 Brownout reset

The brownout reset generator puts the system in a reset state if VDD drops below the brownout reset
(BOR) threshold.
See section Power fail comparator on page 155 for more information.

5.3.6.7 Retained registers

A retained register is one that will retain its value in System OFF mode and through a reset, depending
on the reset source. See the individual peripheral chapters for information on which of their registers are
retained.

5.3.6.8 Reset behavior

The various reset sources and their targets are summarized in the table below.

Reset source Reset target

CPU Peripherals GPIO Debug6 SWJ-DP RAM WDT Retained RESETREAS

registers

CPU lockup 7 x x x

Soft reset x x x
Wakeup from System OFF x x x8 x9 x
mode reset

Watchdog reset 10 x x x x x x x

Pin reset x x x x x x x
Brownout reset x x x x x x x x x
Power-on reset x x x x x x x x x

Note: The RAM is never reset, but depending on a reset source the content of RAM may be
corrupted.

5.3.7 Registers
Instances

Instance Base address Description

POWER 0x40000000 Power control

Register overview

Register Offset Description

TASKS_CONSTLAT 0x78 Enable Constant Latency mode

6
All debug components excluding SWJ-DP. See Debug and trace on page 66 for more information
about the different debug components.
7
Reset from CPU lockup is disabled if the device is in Debug Interface mode. CPU lockup is not
possible in System OFF.
8
The debug components will not be reset if the device is in Debug Interface mode.
9
RAM is not reset on wakeup from System OFF mode. RAM, or certain parts of RAM, may not be
retained after the device has entered System OFF mode, depending on the settings in the RAM
registers.
10
Watchdog reset is not available in System OFF.

4413_417 v1.9 89
 Power and clock management

Register Offset Description

TASKS_LOWPWR 0x7C Enable Low-power mode (variable latency)
EVENTS_POFWARN 0x108 Power failure warning
EVENTS_SLEEPENTER 0x114 CPU entered WFI/WFE sleep
EVENTS_SLEEPEXIT 0x118 CPU exited WFI/WFE sleep
EVENTS_USBDETECTED 0x11C Voltage supply detected on VBUS
EVENTS_USBREMOVED 0x120 Voltage supply removed from VBUS
EVENTS_USBPWRRDY 0x124 USB 3.3 V supply ready
INTENSET 0x304 Enable interrupt
INTENCLR 0x308 Disable interrupt
RESETREAS 0x400 Reset reason
RAMSTATUS 0x428 RAM status register

This register is deprecated.

USBREGSTATUS 0x438 USB supply status
SYSTEMOFF 0x500 System OFF register
POFCON 0x510 Power-fail comparator configuration
GPREGRET 0x51C General purpose retention register
GPREGRET2 0x520 General purpose retention register
DCDCEN 0x578 Enable DC/DC converter for REG1 stage
DCDCEN0 0x580 Enable DC/DC converter for REG0 stage
MAINREGSTATUS 0x640 Main supply status
RAM[0].POWER 0x900 RAM0 power control register
RAM[0].POWERSET 0x904 RAM0 power control set register
RAM[0].POWERCLR 0x908 RAM0 power control clear register
RAM[1].POWER 0x910 RAM1 power control register
RAM[1].POWERSET 0x914 RAM1 power control set register
RAM[1].POWERCLR 0x918 RAM1 power control clear register
RAM[2].POWER 0x920 RAM2 power control register
RAM[2].POWERSET 0x924 RAM2 power control set register
RAM[2].POWERCLR 0x928 RAM2 power control clear register
RAM[3].POWER 0x930 RAM3 power control register
RAM[3].POWERSET 0x934 RAM3 power control set register
RAM[3].POWERCLR 0x938 RAM3 power control clear register
RAM[4].POWER 0x940 RAM4 power control register
RAM[4].POWERSET 0x944 RAM4 power control set register
RAM[4].POWERCLR 0x948 RAM4 power control clear register
RAM[5].POWER 0x950 RAM5 power control register
RAM[5].POWERSET 0x954 RAM5 power control set register
RAM[5].POWERCLR 0x958 RAM5 power control clear register
RAM[6].POWER 0x960 RAM6 power control register
RAM[6].POWERSET 0x964 RAM6 power control set register
RAM[6].POWERCLR 0x968 RAM6 power control clear register
RAM[7].POWER 0x970 RAM7 power control register
RAM[7].POWERSET 0x974 RAM7 power control set register
RAM[7].POWERCLR 0x978 RAM7 power control clear register
RAM[8].POWER 0x980 RAM8 power control register
RAM[8].POWERSET 0x984 RAM8 power control set register
RAM[8].POWERCLR 0x988 RAM8 power control clear register

5.3.7.1 TASKS_CONSTLAT
Address offset: 0x78
Enable Constant Latency mode

4413_417 v1.9 90
 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_CONSTLAT Enable Constant Latency mode
Trigger 1 Trigger task

5.3.7.2 TASKS_LOWPWR
Address offset: 0x7C
Enable Low-power mode (variable latency)

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_LOWPWR Enable Low-power mode (variable latency)
Trigger 1 Trigger task

5.3.7.3 EVENTS_POFWARN
Address offset: 0x108
Power failure warning

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_POFWARN Power failure warning
NotGenerated 0 Event not generated
Generated 1 Event generated

5.3.7.4 EVENTS_SLEEPENTER
Address offset: 0x114
CPU entered WFI/WFE sleep

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_SLEEPENTER CPU entered WFI/WFE sleep
NotGenerated 0 Event not generated
Generated 1 Event generated

5.3.7.5 EVENTS_SLEEPEXIT
Address offset: 0x118
CPU exited WFI/WFE sleep

4413_417 v1.9 91
 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_SLEEPEXIT CPU exited WFI/WFE sleep
NotGenerated 0 Event not generated
Generated 1 Event generated

5.3.7.6 EVENTS_USBDETECTED
Address offset: 0x11C
Voltage supply detected on VBUS

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_USBDETECTED Voltage supply detected on VBUS
NotGenerated 0 Event not generated
Generated 1 Event generated

5.3.7.7 EVENTS_USBREMOVED
Address offset: 0x120
Voltage supply removed from VBUS

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_USBREMOVED Voltage supply removed from VBUS
NotGenerated 0 Event not generated
Generated 1 Event generated

5.3.7.8 EVENTS_USBPWRRDY
Address offset: 0x124
USB 3.3 V supply ready

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_USBPWRRDY USB 3.3 V supply ready
NotGenerated 0 Event not generated
Generated 1 Event generated

5.3.7.9 INTENSET
Address offset: 0x304
Enable interrupt

4413_417 v1.9 92
 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW POFWARN Write '1' to enable interrupt for event POFWARN
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW SLEEPENTER Write '1' to enable interrupt for event SLEEPENTER
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW SLEEPEXIT Write '1' to enable interrupt for event SLEEPEXIT
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
D RW USBDETECTED Write '1' to enable interrupt for event USBDETECTED
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
E RW USBREMOVED Write '1' to enable interrupt for event USBREMOVED
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
F RW USBPWRRDY Write '1' to enable interrupt for event USBPWRRDY
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

5.3.7.10 INTENCLR
Address offset: 0x308
Disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW POFWARN Write '1' to disable interrupt for event POFWARN
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW SLEEPENTER Write '1' to disable interrupt for event SLEEPENTER
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW SLEEPEXIT Write '1' to disable interrupt for event SLEEPEXIT
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
D RW USBDETECTED Write '1' to disable interrupt for event USBDETECTED
Clear 1 Disable
Disabled 0 Read: Disabled

4413_417 v1.9 93
 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Enabled 1 Read: Enabled
E RW USBREMOVED Write '1' to disable interrupt for event USBREMOVED
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
F RW USBPWRRDY Write '1' to disable interrupt for event USBPWRRDY
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

5.3.7.11 RESETREAS
Address offset: 0x400
Reset reason

Note: Unless cleared, the RESETREAS register will be cumulative. A field is cleared by writing '1' to
it. If none of the reset sources are flagged, this indicates that the chip was reset from the on-chip
reset generator, which will indicate a power-on-reset or a brownout reset.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW RESETPIN Reset from pin-reset detected
NotDetected 0 Not detected
Detected 1 Detected
B RW DOG Reset from watchdog detected
NotDetected 0 Not detected
Detected 1 Detected
C RW SREQ Reset from soft reset detected
NotDetected 0 Not detected
Detected 1 Detected
D RW LOCKUP Reset from CPU lock-up detected
NotDetected 0 Not detected
Detected 1 Detected
E RW OFF Reset due to wake up from System OFF mode when wakeup is triggered
from DETECT signal from GPIO
NotDetected 0 Not detected
Detected 1 Detected
F RW LPCOMP Reset due to wake up from System OFF mode when wakeup is triggered
from ANADETECT signal from LPCOMP
NotDetected 0 Not detected
Detected 1 Detected
G RW DIF Reset due to wake up from System OFF mode when wakeup is triggered
from entering into debug interface mode
NotDetected 0 Not detected
Detected 1 Detected
H RW NFC Reset due to wake up from System OFF mode by NFC field detect
NotDetected 0 Not detected

4413_417 v1.9 94
 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Detected 1 Detected
I RW VBUS Reset due to wake up from System OFF mode by VBUS rising into valid range
NotDetected 0 Not detected
Detected 1 Detected

5.3.7.12 RAMSTATUS (Deprecated)

Address offset: 0x428
RAM status register
This register is deprecated.

Note: Since this register is deprecated the following substitutions have been made: RAM block 0
is equivalent to a block comprising RAM0.S0 and RAM1.S0. RAM block 1 is equivalent to a block
comprising RAM2.S0 and RAM3.S0. RAM block 2 is equivalent to a block comprising RAM4.S0 and
RAM5.S0. RAM block 3 is equivalent to a block comprising RAM6.S0 and RAM7.S0. A RAM block
field will indicate ON as long as any of the RAM sections associated with a block are on.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R RAMBLOCK0 RAM block 0 is on or off/powering up
Off 0 Off
On 1 On
B R RAMBLOCK1 RAM block 1 is on or off/powering up
Off 0 Off
On 1 On
C R RAMBLOCK2 RAM block 2 is on or off/powering up
Off 0 Off
On 1 On
D R RAMBLOCK3 RAM block 3 is on or off/powering up
Off 0 Off
On 1 On

5.3.7.13 USBREGSTATUS
Address offset: 0x438
USB supply status

Note:

4413_417 v1.9 95
 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R VBUSDETECT VBUS input detection status (USBDETECTED and USBREMOVED events are
derived from this information)
NoVbus 0 VBUS voltage below valid threshold
VbusPresent 1 VBUS voltage above valid threshold
B R OUTPUTRDY USB supply output settling time elapsed
NotReady 0 USBREG output settling time not elapsed
Ready 1 USBREG output settling time elapsed (same information as USBPWRRDY
event)

5.3.7.14 SYSTEMOFF
Address offset: 0x500
System OFF register

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W SYSTEMOFF Enable System OFF mode
Enter 1 Enable System OFF mode

5.3.7.15 POFCON
Address offset: 0x510
Power-fail comparator configuration

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C C C C B B B B A
Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW POF Enable or disable power failure warning
Disabled 0 Disable
Enabled 1 Enable
B RW THRESHOLD Power-fail comparator threshold setting. This setting applies both for
normal voltage mode (supply connected to both VDD and VDDH) and high
voltage mode (supply connected to VDDH only). Values 0-3 set threshold
below 1.7 V and should not be used as brown out detection will be activated
before power failure warning on such low voltages.
V17 4 Set threshold to 1.7 V
V18 5 Set threshold to 1.8 V
V19 6 Set threshold to 1.9 V
V20 7 Set threshold to 2.0 V
V21 8 Set threshold to 2.1 V
V22 9 Set threshold to 2.2 V
V23 10 Set threshold to 2.3 V
V24 11 Set threshold to 2.4 V
V25 12 Set threshold to 2.5 V
V26 13 Set threshold to 2.6 V
V27 14 Set threshold to 2.7 V

4413_417 v1.9 96
 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C C C C B B B B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
V28 15 Set threshold to 2.8 V
C RW THRESHOLDVDDH Power-fail comparator threshold setting for high voltage mode (supply
connected to VDDH only). This setting does not apply for normal voltage
mode (supply connected to both VDD and VDDH).
V27 0 Set threshold to 2.7 V
V28 1 Set threshold to 2.8 V
V29 2 Set threshold to 2.9 V
V30 3 Set threshold to 3.0 V
V31 4 Set threshold to 3.1 V
V32 5 Set threshold to 3.2 V
V33 6 Set threshold to 3.3 V
V34 7 Set threshold to 3.4 V
V35 8 Set threshold to 3.5 V
V36 9 Set threshold to 3.6 V
V37 10 Set threshold to 3.7 V
V38 11 Set threshold to 3.8 V
V39 12 Set threshold to 3.9 V
V40 13 Set threshold to 4.0 V
V41 14 Set threshold to 4.1 V
V42 15 Set threshold to 4.2 V

5.3.7.16 GPREGRET
Address offset: 0x51C
General purpose retention register

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW GPREGRET General purpose retention register

This register is a retained register

5.3.7.17 GPREGRET2
Address offset: 0x520
General purpose retention register

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW GPREGRET General purpose retention register

This register is a retained register

5.3.7.18 DCDCEN
Address offset: 0x578

4413_417 v1.9 97
 Power and clock management

Enable DC/DC converter for REG1 stage

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A
Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW DCDCEN Enable DC/DC converter for REG1 stage.
Disabled 0 Disable
Enabled 1 Enable

5.3.7.19 DCDCEN0
Address offset: 0x580
Enable DC/DC converter for REG0 stage

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW DCDCEN Enable DC/DC converter for REG0 stage.
Disabled 0 Disable
Enabled 1 Enable

5.3.7.20 MAINREGSTATUS
Address offset: 0x640
Main supply status

Note:

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R MAINREGSTATUS Main supply status
Normal 0 Normal voltage mode. Voltage supplied on VDD.
High 1 High voltage mode. Voltage supplied on VDDH.

5.3.7.21 RAM[0].POWER
Address offset: 0x900
RAM0 power control register

4413_417 v1.9 98
 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW S0POWER Keep RAM section S0 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S0RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
B RW S1POWER Keep RAM section S1 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S1RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
C RW S2POWER Keep RAM section S2 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S2RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
D RW S3POWER Keep RAM section S3 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S3RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
E RW S4POWER Keep RAM section S4 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S4RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
F RW S5POWER Keep RAM section S5 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S5RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
G RW S6POWER Keep RAM section S6 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S6RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
H RW S7POWER Keep RAM section S7 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S7RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On

4413_417 v1.9 99
 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
I RW S8POWER Keep RAM section S8 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S8RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
J RW S9POWER Keep RAM section S9 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S9RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
K RW S10POWER Keep RAM section S10 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S10RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
L RW S11POWER Keep RAM section S11 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S11RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
M RW S12POWER Keep RAM section S12 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S12RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
N RW S13POWER Keep RAM section S13 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S13RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
O RW S14POWER Keep RAM section S14 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S14RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
P RW S15POWER Keep RAM section S15 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S15RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On

4413_417 v1.9 100

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
Q RW S0RETENTION Keep retention on RAM section S0 when RAM section is off
Off 0 Off
On 1 On
R RW S1RETENTION Keep retention on RAM section S1 when RAM section is off
Off 0 Off
On 1 On
S RW S2RETENTION Keep retention on RAM section S2 when RAM section is off
Off 0 Off
On 1 On
T RW S3RETENTION Keep retention on RAM section S3 when RAM section is off
Off 0 Off
On 1 On
U RW S4RETENTION Keep retention on RAM section S4 when RAM section is off
Off 0 Off
On 1 On
V RW S5RETENTION Keep retention on RAM section S5 when RAM section is off
Off 0 Off
On 1 On
W RW S6RETENTION Keep retention on RAM section S6 when RAM section is off
Off 0 Off
On 1 On
X RW S7RETENTION Keep retention on RAM section S7 when RAM section is off
Off 0 Off
On 1 On
Y RW S8RETENTION Keep retention on RAM section S8 when RAM section is off
Off 0 Off
On 1 On
Z RW S9RETENTION Keep retention on RAM section S9 when RAM section is off
Off 0 Off
On 1 On
a RW S10RETENTION Keep retention on RAM section S10 when RAM section is off
Off 0 Off
On 1 On
b RW S11RETENTION Keep retention on RAM section S11 when RAM section is off
Off 0 Off
On 1 On
c RW S12RETENTION Keep retention on RAM section S12 when RAM section is off
Off 0 Off
On 1 On
d RW S13RETENTION Keep retention on RAM section S13 when RAM section is off
Off 0 Off
On 1 On
e RW S14RETENTION Keep retention on RAM section S14 when RAM section is off
Off 0 Off
On 1 On
f RW S15RETENTION Keep retention on RAM section S15 when RAM section is off
Off 0 Off
On 1 On

4413_417 v1.9 101

 Power and clock management

5.3.7.22 RAM[0].POWERSET
Address offset: 0x904
RAM0 power control set register
When read, this register will return the value of the POWER register.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A W S0POWER Keep RAM section S0 of RAM0 on or off in System ON mode
On 1 On
B W S1POWER Keep RAM section S1 of RAM0 on or off in System ON mode
On 1 On
C W S2POWER Keep RAM section S2 of RAM0 on or off in System ON mode
On 1 On
D W S3POWER Keep RAM section S3 of RAM0 on or off in System ON mode
On 1 On
E W S4POWER Keep RAM section S4 of RAM0 on or off in System ON mode
On 1 On
F W S5POWER Keep RAM section S5 of RAM0 on or off in System ON mode
On 1 On
G W S6POWER Keep RAM section S6 of RAM0 on or off in System ON mode
On 1 On
H W S7POWER Keep RAM section S7 of RAM0 on or off in System ON mode
On 1 On
I W S8POWER Keep RAM section S8 of RAM0 on or off in System ON mode
On 1 On
J W S9POWER Keep RAM section S9 of RAM0 on or off in System ON mode
On 1 On
K W S10POWER Keep RAM section S10 of RAM0 on or off in System ON mode
On 1 On
L W S11POWER Keep RAM section S11 of RAM0 on or off in System ON mode
On 1 On
M W S12POWER Keep RAM section S12 of RAM0 on or off in System ON mode
On 1 On
N W S13POWER Keep RAM section S13 of RAM0 on or off in System ON mode
On 1 On
O W S14POWER Keep RAM section S14 of RAM0 on or off in System ON mode
On 1 On
P W S15POWER Keep RAM section S15 of RAM0 on or off in System ON mode
On 1 On
Q W S0RETENTION Keep retention on RAM section S0 when RAM section is switched off
On 1 On
R W S1RETENTION Keep retention on RAM section S1 when RAM section is switched off
On 1 On
S W S2RETENTION Keep retention on RAM section S2 when RAM section is switched off
On 1 On
T W S3RETENTION Keep retention on RAM section S3 when RAM section is switched off
On 1 On
U W S4RETENTION Keep retention on RAM section S4 when RAM section is switched off
On 1 On
V W S5RETENTION Keep retention on RAM section S5 when RAM section is switched off

4413_417 v1.9 102

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
On 1 On
W W S6RETENTION Keep retention on RAM section S6 when RAM section is switched off
On 1 On
X W S7RETENTION Keep retention on RAM section S7 when RAM section is switched off
On 1 On
Y W S8RETENTION Keep retention on RAM section S8 when RAM section is switched off
On 1 On
Z W S9RETENTION Keep retention on RAM section S9 when RAM section is switched off
On 1 On
a W S10RETENTION Keep retention on RAM section S10 when RAM section is switched off
On 1 On
b W S11RETENTION Keep retention on RAM section S11 when RAM section is switched off
On 1 On
c W S12RETENTION Keep retention on RAM section S12 when RAM section is switched off
On 1 On
d W S13RETENTION Keep retention on RAM section S13 when RAM section is switched off
On 1 On
e W S14RETENTION Keep retention on RAM section S14 when RAM section is switched off
On 1 On
f W S15RETENTION Keep retention on RAM section S15 when RAM section is switched off
On 1 On

5.3.7.23 RAM[0].POWERCLR
Address offset: 0x908
RAM0 power control clear register
When read, this register will return the value of the POWER register.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A W S0POWER Keep RAM section S0 of RAM0 on or off in System ON mode
Off 1 Off
B W S1POWER Keep RAM section S1 of RAM0 on or off in System ON mode
Off 1 Off
C W S2POWER Keep RAM section S2 of RAM0 on or off in System ON mode
Off 1 Off
D W S3POWER Keep RAM section S3 of RAM0 on or off in System ON mode
Off 1 Off
E W S4POWER Keep RAM section S4 of RAM0 on or off in System ON mode
Off 1 Off
F W S5POWER Keep RAM section S5 of RAM0 on or off in System ON mode
Off 1 Off
G W S6POWER Keep RAM section S6 of RAM0 on or off in System ON mode
Off 1 Off
H W S7POWER Keep RAM section S7 of RAM0 on or off in System ON mode
Off 1 Off
I W S8POWER Keep RAM section S8 of RAM0 on or off in System ON mode

4413_417 v1.9 103

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
Off 1 Off
J W S9POWER Keep RAM section S9 of RAM0 on or off in System ON mode
Off 1 Off
K W S10POWER Keep RAM section S10 of RAM0 on or off in System ON mode
Off 1 Off
L W S11POWER Keep RAM section S11 of RAM0 on or off in System ON mode
Off 1 Off
M W S12POWER Keep RAM section S12 of RAM0 on or off in System ON mode
Off 1 Off
N W S13POWER Keep RAM section S13 of RAM0 on or off in System ON mode
Off 1 Off
O W S14POWER Keep RAM section S14 of RAM0 on or off in System ON mode
Off 1 Off
P W S15POWER Keep RAM section S15 of RAM0 on or off in System ON mode
Off 1 Off
Q W S0RETENTION Keep retention on RAM section S0 when RAM section is switched off
Off 1 Off
R W S1RETENTION Keep retention on RAM section S1 when RAM section is switched off
Off 1 Off
S W S2RETENTION Keep retention on RAM section S2 when RAM section is switched off
Off 1 Off
T W S3RETENTION Keep retention on RAM section S3 when RAM section is switched off
Off 1 Off
U W S4RETENTION Keep retention on RAM section S4 when RAM section is switched off
Off 1 Off
V W S5RETENTION Keep retention on RAM section S5 when RAM section is switched off
Off 1 Off
W W S6RETENTION Keep retention on RAM section S6 when RAM section is switched off
Off 1 Off
X W S7RETENTION Keep retention on RAM section S7 when RAM section is switched off
Off 1 Off
Y W S8RETENTION Keep retention on RAM section S8 when RAM section is switched off
Off 1 Off
Z W S9RETENTION Keep retention on RAM section S9 when RAM section is switched off
Off 1 Off
a W S10RETENTION Keep retention on RAM section S10 when RAM section is switched off
Off 1 Off
b W S11RETENTION Keep retention on RAM section S11 when RAM section is switched off
Off 1 Off
c W S12RETENTION Keep retention on RAM section S12 when RAM section is switched off
Off 1 Off
d W S13RETENTION Keep retention on RAM section S13 when RAM section is switched off
Off 1 Off
e W S14RETENTION Keep retention on RAM section S14 when RAM section is switched off
Off 1 Off
f W S15RETENTION Keep retention on RAM section S15 when RAM section is switched off
Off 1 Off

5.3.7.24 RAM[1].POWER
Address offset: 0x910

4413_417 v1.9 104

 Power and clock management

RAM1 power control register

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A
Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW S0POWER Keep RAM section S0 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S0RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
B RW S1POWER Keep RAM section S1 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S1RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
C RW S2POWER Keep RAM section S2 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S2RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
D RW S3POWER Keep RAM section S3 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S3RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
E RW S4POWER Keep RAM section S4 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S4RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
F RW S5POWER Keep RAM section S5 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S5RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
G RW S6POWER Keep RAM section S6 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S6RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On

4413_417 v1.9 105

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
H RW S7POWER Keep RAM section S7 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S7RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
I RW S8POWER Keep RAM section S8 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S8RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
J RW S9POWER Keep RAM section S9 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S9RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
K RW S10POWER Keep RAM section S10 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S10RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
L RW S11POWER Keep RAM section S11 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S11RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
M RW S12POWER Keep RAM section S12 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S12RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
N RW S13POWER Keep RAM section S13 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S13RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
O RW S14POWER Keep RAM section S14 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S14RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On

4413_417 v1.9 106

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
P RW S15POWER Keep RAM section S15 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S15RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
Q RW S0RETENTION Keep retention on RAM section S0 when RAM section is off
Off 0 Off
On 1 On
R RW S1RETENTION Keep retention on RAM section S1 when RAM section is off
Off 0 Off
On 1 On
S RW S2RETENTION Keep retention on RAM section S2 when RAM section is off
Off 0 Off
On 1 On
T RW S3RETENTION Keep retention on RAM section S3 when RAM section is off
Off 0 Off
On 1 On
U RW S4RETENTION Keep retention on RAM section S4 when RAM section is off
Off 0 Off
On 1 On
V RW S5RETENTION Keep retention on RAM section S5 when RAM section is off
Off 0 Off
On 1 On
W RW S6RETENTION Keep retention on RAM section S6 when RAM section is off
Off 0 Off
On 1 On
X RW S7RETENTION Keep retention on RAM section S7 when RAM section is off
Off 0 Off
On 1 On
Y RW S8RETENTION Keep retention on RAM section S8 when RAM section is off
Off 0 Off
On 1 On
Z RW S9RETENTION Keep retention on RAM section S9 when RAM section is off
Off 0 Off
On 1 On
a RW S10RETENTION Keep retention on RAM section S10 when RAM section is off
Off 0 Off
On 1 On
b RW S11RETENTION Keep retention on RAM section S11 when RAM section is off
Off 0 Off
On 1 On
c RW S12RETENTION Keep retention on RAM section S12 when RAM section is off
Off 0 Off
On 1 On
d RW S13RETENTION Keep retention on RAM section S13 when RAM section is off
Off 0 Off
On 1 On
e RW S14RETENTION Keep retention on RAM section S14 when RAM section is off
Off 0 Off

4413_417 v1.9 107

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
On 1 On
f RW S15RETENTION Keep retention on RAM section S15 when RAM section is off
Off 0 Off
On 1 On

5.3.7.25 RAM[1].POWERSET
Address offset: 0x914
RAM1 power control set register
When read, this register will return the value of the POWER register.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A W S0POWER Keep RAM section S0 of RAM1 on or off in System ON mode
On 1 On
B W S1POWER Keep RAM section S1 of RAM1 on or off in System ON mode
On 1 On
C W S2POWER Keep RAM section S2 of RAM1 on or off in System ON mode
On 1 On
D W S3POWER Keep RAM section S3 of RAM1 on or off in System ON mode
On 1 On
E W S4POWER Keep RAM section S4 of RAM1 on or off in System ON mode
On 1 On
F W S5POWER Keep RAM section S5 of RAM1 on or off in System ON mode
On 1 On
G W S6POWER Keep RAM section S6 of RAM1 on or off in System ON mode
On 1 On
H W S7POWER Keep RAM section S7 of RAM1 on or off in System ON mode
On 1 On
I W S8POWER Keep RAM section S8 of RAM1 on or off in System ON mode
On 1 On
J W S9POWER Keep RAM section S9 of RAM1 on or off in System ON mode
On 1 On
K W S10POWER Keep RAM section S10 of RAM1 on or off in System ON mode
On 1 On
L W S11POWER Keep RAM section S11 of RAM1 on or off in System ON mode
On 1 On
M W S12POWER Keep RAM section S12 of RAM1 on or off in System ON mode
On 1 On
N W S13POWER Keep RAM section S13 of RAM1 on or off in System ON mode
On 1 On
O W S14POWER Keep RAM section S14 of RAM1 on or off in System ON mode
On 1 On
P W S15POWER Keep RAM section S15 of RAM1 on or off in System ON mode
On 1 On
Q W S0RETENTION Keep retention on RAM section S0 when RAM section is switched off
On 1 On

4413_417 v1.9 108

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
R W S1RETENTION Keep retention on RAM section S1 when RAM section is switched off
On 1 On
S W S2RETENTION Keep retention on RAM section S2 when RAM section is switched off
On 1 On
T W S3RETENTION Keep retention on RAM section S3 when RAM section is switched off
On 1 On
U W S4RETENTION Keep retention on RAM section S4 when RAM section is switched off
On 1 On
V W S5RETENTION Keep retention on RAM section S5 when RAM section is switched off
On 1 On
W W S6RETENTION Keep retention on RAM section S6 when RAM section is switched off
On 1 On
X W S7RETENTION Keep retention on RAM section S7 when RAM section is switched off
On 1 On
Y W S8RETENTION Keep retention on RAM section S8 when RAM section is switched off
On 1 On
Z W S9RETENTION Keep retention on RAM section S9 when RAM section is switched off
On 1 On
a W S10RETENTION Keep retention on RAM section S10 when RAM section is switched off
On 1 On
b W S11RETENTION Keep retention on RAM section S11 when RAM section is switched off
On 1 On
c W S12RETENTION Keep retention on RAM section S12 when RAM section is switched off
On 1 On
d W S13RETENTION Keep retention on RAM section S13 when RAM section is switched off
On 1 On
e W S14RETENTION Keep retention on RAM section S14 when RAM section is switched off
On 1 On
f W S15RETENTION Keep retention on RAM section S15 when RAM section is switched off
On 1 On

5.3.7.26 RAM[1].POWERCLR
Address offset: 0x918
RAM1 power control clear register
When read, this register will return the value of the POWER register.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A W S0POWER Keep RAM section S0 of RAM1 on or off in System ON mode
Off 1 Off
B W S1POWER Keep RAM section S1 of RAM1 on or off in System ON mode
Off 1 Off
C W S2POWER Keep RAM section S2 of RAM1 on or off in System ON mode
Off 1 Off
D W S3POWER Keep RAM section S3 of RAM1 on or off in System ON mode
Off 1 Off

4413_417 v1.9 109

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
E W S4POWER Keep RAM section S4 of RAM1 on or off in System ON mode
Off 1 Off
F W S5POWER Keep RAM section S5 of RAM1 on or off in System ON mode
Off 1 Off
G W S6POWER Keep RAM section S6 of RAM1 on or off in System ON mode
Off 1 Off
H W S7POWER Keep RAM section S7 of RAM1 on or off in System ON mode
Off 1 Off
I W S8POWER Keep RAM section S8 of RAM1 on or off in System ON mode
Off 1 Off
J W S9POWER Keep RAM section S9 of RAM1 on or off in System ON mode
Off 1 Off
K W S10POWER Keep RAM section S10 of RAM1 on or off in System ON mode
Off 1 Off
L W S11POWER Keep RAM section S11 of RAM1 on or off in System ON mode
Off 1 Off
M W S12POWER Keep RAM section S12 of RAM1 on or off in System ON mode
Off 1 Off
N W S13POWER Keep RAM section S13 of RAM1 on or off in System ON mode
Off 1 Off
O W S14POWER Keep RAM section S14 of RAM1 on or off in System ON mode
Off 1 Off
P W S15POWER Keep RAM section S15 of RAM1 on or off in System ON mode
Off 1 Off
Q W S0RETENTION Keep retention on RAM section S0 when RAM section is switched off
Off 1 Off
R W S1RETENTION Keep retention on RAM section S1 when RAM section is switched off
Off 1 Off
S W S2RETENTION Keep retention on RAM section S2 when RAM section is switched off
Off 1 Off
T W S3RETENTION Keep retention on RAM section S3 when RAM section is switched off
Off 1 Off
U W S4RETENTION Keep retention on RAM section S4 when RAM section is switched off
Off 1 Off
V W S5RETENTION Keep retention on RAM section S5 when RAM section is switched off
Off 1 Off
W W S6RETENTION Keep retention on RAM section S6 when RAM section is switched off
Off 1 Off
X W S7RETENTION Keep retention on RAM section S7 when RAM section is switched off
Off 1 Off
Y W S8RETENTION Keep retention on RAM section S8 when RAM section is switched off
Off 1 Off
Z W S9RETENTION Keep retention on RAM section S9 when RAM section is switched off
Off 1 Off
a W S10RETENTION Keep retention on RAM section S10 when RAM section is switched off
Off 1 Off
b W S11RETENTION Keep retention on RAM section S11 when RAM section is switched off
Off 1 Off
c W S12RETENTION Keep retention on RAM section S12 when RAM section is switched off
Off 1 Off

4413_417 v1.9 110

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
d W S13RETENTION Keep retention on RAM section S13 when RAM section is switched off
Off 1 Off
e W S14RETENTION Keep retention on RAM section S14 when RAM section is switched off
Off 1 Off
f W S15RETENTION Keep retention on RAM section S15 when RAM section is switched off
Off 1 Off

5.3.7.27 RAM[2].POWER
Address offset: 0x920
RAM2 power control register

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW S0POWER Keep RAM section S0 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S0RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
B RW S1POWER Keep RAM section S1 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S1RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
C RW S2POWER Keep RAM section S2 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S2RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
D RW S3POWER Keep RAM section S3 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S3RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
E RW S4POWER Keep RAM section S4 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S4RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On

4413_417 v1.9 111

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
F RW S5POWER Keep RAM section S5 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S5RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
G RW S6POWER Keep RAM section S6 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S6RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
H RW S7POWER Keep RAM section S7 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S7RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
I RW S8POWER Keep RAM section S8 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S8RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
J RW S9POWER Keep RAM section S9 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S9RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
K RW S10POWER Keep RAM section S10 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S10RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
L RW S11POWER Keep RAM section S11 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S11RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
M RW S12POWER Keep RAM section S12 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S12RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On

4413_417 v1.9 112

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
N RW S13POWER Keep RAM section S13 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S13RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
O RW S14POWER Keep RAM section S14 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S14RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
P RW S15POWER Keep RAM section S15 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S15RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
Q RW S0RETENTION Keep retention on RAM section S0 when RAM section is off
Off 0 Off
On 1 On
R RW S1RETENTION Keep retention on RAM section S1 when RAM section is off
Off 0 Off
On 1 On
S RW S2RETENTION Keep retention on RAM section S2 when RAM section is off
Off 0 Off
On 1 On
T RW S3RETENTION Keep retention on RAM section S3 when RAM section is off
Off 0 Off
On 1 On
U RW S4RETENTION Keep retention on RAM section S4 when RAM section is off
Off 0 Off
On 1 On
V RW S5RETENTION Keep retention on RAM section S5 when RAM section is off
Off 0 Off
On 1 On
W RW S6RETENTION Keep retention on RAM section S6 when RAM section is off
Off 0 Off
On 1 On
X RW S7RETENTION Keep retention on RAM section S7 when RAM section is off
Off 0 Off
On 1 On
Y RW S8RETENTION Keep retention on RAM section S8 when RAM section is off
Off 0 Off
On 1 On
Z RW S9RETENTION Keep retention on RAM section S9 when RAM section is off
Off 0 Off
On 1 On
a RW S10RETENTION Keep retention on RAM section S10 when RAM section is off

4413_417 v1.9 113

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
Off 0 Off
On 1 On
b RW S11RETENTION Keep retention on RAM section S11 when RAM section is off
Off 0 Off
On 1 On
c RW S12RETENTION Keep retention on RAM section S12 when RAM section is off
Off 0 Off
On 1 On
d RW S13RETENTION Keep retention on RAM section S13 when RAM section is off
Off 0 Off
On 1 On
e RW S14RETENTION Keep retention on RAM section S14 when RAM section is off
Off 0 Off
On 1 On
f RW S15RETENTION Keep retention on RAM section S15 when RAM section is off
Off 0 Off
On 1 On

5.3.7.28 RAM[2].POWERSET
Address offset: 0x924
RAM2 power control set register
When read, this register will return the value of the POWER register.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A W S0POWER Keep RAM section S0 of RAM2 on or off in System ON mode
On 1 On
B W S1POWER Keep RAM section S1 of RAM2 on or off in System ON mode
On 1 On
C W S2POWER Keep RAM section S2 of RAM2 on or off in System ON mode
On 1 On
D W S3POWER Keep RAM section S3 of RAM2 on or off in System ON mode
On 1 On
E W S4POWER Keep RAM section S4 of RAM2 on or off in System ON mode
On 1 On
F W S5POWER Keep RAM section S5 of RAM2 on or off in System ON mode
On 1 On
G W S6POWER Keep RAM section S6 of RAM2 on or off in System ON mode
On 1 On
H W S7POWER Keep RAM section S7 of RAM2 on or off in System ON mode
On 1 On
I W S8POWER Keep RAM section S8 of RAM2 on or off in System ON mode
On 1 On
J W S9POWER Keep RAM section S9 of RAM2 on or off in System ON mode
On 1 On
K W S10POWER Keep RAM section S10 of RAM2 on or off in System ON mode

4413_417 v1.9 114

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
On 1 On
L W S11POWER Keep RAM section S11 of RAM2 on or off in System ON mode
On 1 On
M W S12POWER Keep RAM section S12 of RAM2 on or off in System ON mode
On 1 On
N W S13POWER Keep RAM section S13 of RAM2 on or off in System ON mode
On 1 On
O W S14POWER Keep RAM section S14 of RAM2 on or off in System ON mode
On 1 On
P W S15POWER Keep RAM section S15 of RAM2 on or off in System ON mode
On 1 On
Q W S0RETENTION Keep retention on RAM section S0 when RAM section is switched off
On 1 On
R W S1RETENTION Keep retention on RAM section S1 when RAM section is switched off
On 1 On
S W S2RETENTION Keep retention on RAM section S2 when RAM section is switched off
On 1 On
T W S3RETENTION Keep retention on RAM section S3 when RAM section is switched off
On 1 On
U W S4RETENTION Keep retention on RAM section S4 when RAM section is switched off
On 1 On
V W S5RETENTION Keep retention on RAM section S5 when RAM section is switched off
On 1 On
W W S6RETENTION Keep retention on RAM section S6 when RAM section is switched off
On 1 On
X W S7RETENTION Keep retention on RAM section S7 when RAM section is switched off
On 1 On
Y W S8RETENTION Keep retention on RAM section S8 when RAM section is switched off
On 1 On
Z W S9RETENTION Keep retention on RAM section S9 when RAM section is switched off
On 1 On
a W S10RETENTION Keep retention on RAM section S10 when RAM section is switched off
On 1 On
b W S11RETENTION Keep retention on RAM section S11 when RAM section is switched off
On 1 On
c W S12RETENTION Keep retention on RAM section S12 when RAM section is switched off
On 1 On
d W S13RETENTION Keep retention on RAM section S13 when RAM section is switched off
On 1 On
e W S14RETENTION Keep retention on RAM section S14 when RAM section is switched off
On 1 On
f W S15RETENTION Keep retention on RAM section S15 when RAM section is switched off
On 1 On

5.3.7.29 RAM[2].POWERCLR
Address offset: 0x928
RAM2 power control clear register
When read, this register will return the value of the POWER register.

4413_417 v1.9 115

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A W S0POWER Keep RAM section S0 of RAM2 on or off in System ON mode
Off 1 Off
B W S1POWER Keep RAM section S1 of RAM2 on or off in System ON mode
Off 1 Off
C W S2POWER Keep RAM section S2 of RAM2 on or off in System ON mode
Off 1 Off
D W S3POWER Keep RAM section S3 of RAM2 on or off in System ON mode
Off 1 Off
E W S4POWER Keep RAM section S4 of RAM2 on or off in System ON mode
Off 1 Off
F W S5POWER Keep RAM section S5 of RAM2 on or off in System ON mode
Off 1 Off
G W S6POWER Keep RAM section S6 of RAM2 on or off in System ON mode
Off 1 Off
H W S7POWER Keep RAM section S7 of RAM2 on or off in System ON mode
Off 1 Off
I W S8POWER Keep RAM section S8 of RAM2 on or off in System ON mode
Off 1 Off
J W S9POWER Keep RAM section S9 of RAM2 on or off in System ON mode
Off 1 Off
K W S10POWER Keep RAM section S10 of RAM2 on or off in System ON mode
Off 1 Off
L W S11POWER Keep RAM section S11 of RAM2 on or off in System ON mode
Off 1 Off
M W S12POWER Keep RAM section S12 of RAM2 on or off in System ON mode
Off 1 Off
N W S13POWER Keep RAM section S13 of RAM2 on or off in System ON mode
Off 1 Off
O W S14POWER Keep RAM section S14 of RAM2 on or off in System ON mode
Off 1 Off
P W S15POWER Keep RAM section S15 of RAM2 on or off in System ON mode
Off 1 Off
Q W S0RETENTION Keep retention on RAM section S0 when RAM section is switched off
Off 1 Off
R W S1RETENTION Keep retention on RAM section S1 when RAM section is switched off
Off 1 Off
S W S2RETENTION Keep retention on RAM section S2 when RAM section is switched off
Off 1 Off
T W S3RETENTION Keep retention on RAM section S3 when RAM section is switched off
Off 1 Off
U W S4RETENTION Keep retention on RAM section S4 when RAM section is switched off
Off 1 Off
V W S5RETENTION Keep retention on RAM section S5 when RAM section is switched off
Off 1 Off
W W S6RETENTION Keep retention on RAM section S6 when RAM section is switched off
Off 1 Off
X W S7RETENTION Keep retention on RAM section S7 when RAM section is switched off
Off 1 Off
Y W S8RETENTION Keep retention on RAM section S8 when RAM section is switched off
Off 1 Off

4413_417 v1.9 116

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
Z W S9RETENTION Keep retention on RAM section S9 when RAM section is switched off
Off 1 Off
a W S10RETENTION Keep retention on RAM section S10 when RAM section is switched off
Off 1 Off
b W S11RETENTION Keep retention on RAM section S11 when RAM section is switched off
Off 1 Off
c W S12RETENTION Keep retention on RAM section S12 when RAM section is switched off
Off 1 Off
d W S13RETENTION Keep retention on RAM section S13 when RAM section is switched off
Off 1 Off
e W S14RETENTION Keep retention on RAM section S14 when RAM section is switched off
Off 1 Off
f W S15RETENTION Keep retention on RAM section S15 when RAM section is switched off
Off 1 Off

5.3.7.30 RAM[3].POWER
Address offset: 0x930
RAM3 power control register

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW S0POWER Keep RAM section S0 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S0RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
B RW S1POWER Keep RAM section S1 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S1RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
C RW S2POWER Keep RAM section S2 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S2RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
D RW S3POWER Keep RAM section S3 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S3RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On

4413_417 v1.9 117

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
E RW S4POWER Keep RAM section S4 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S4RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
F RW S5POWER Keep RAM section S5 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S5RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
G RW S6POWER Keep RAM section S6 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S6RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
H RW S7POWER Keep RAM section S7 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S7RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
I RW S8POWER Keep RAM section S8 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S8RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
J RW S9POWER Keep RAM section S9 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S9RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
K RW S10POWER Keep RAM section S10 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S10RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
L RW S11POWER Keep RAM section S11 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S11RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On

4413_417 v1.9 118

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
M RW S12POWER Keep RAM section S12 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S12RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
N RW S13POWER Keep RAM section S13 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S13RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
O RW S14POWER Keep RAM section S14 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S14RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
P RW S15POWER Keep RAM section S15 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S15RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
Q RW S0RETENTION Keep retention on RAM section S0 when RAM section is off
Off 0 Off
On 1 On
R RW S1RETENTION Keep retention on RAM section S1 when RAM section is off
Off 0 Off
On 1 On
S RW S2RETENTION Keep retention on RAM section S2 when RAM section is off
Off 0 Off
On 1 On
T RW S3RETENTION Keep retention on RAM section S3 when RAM section is off
Off 0 Off
On 1 On
U RW S4RETENTION Keep retention on RAM section S4 when RAM section is off
Off 0 Off
On 1 On
V RW S5RETENTION Keep retention on RAM section S5 when RAM section is off
Off 0 Off
On 1 On
W RW S6RETENTION Keep retention on RAM section S6 when RAM section is off
Off 0 Off
On 1 On
X RW S7RETENTION Keep retention on RAM section S7 when RAM section is off
Off 0 Off
On 1 On
Y RW S8RETENTION Keep retention on RAM section S8 when RAM section is off

4413_417 v1.9 119

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
Off 0 Off
On 1 On
Z RW S9RETENTION Keep retention on RAM section S9 when RAM section is off
Off 0 Off
On 1 On
a RW S10RETENTION Keep retention on RAM section S10 when RAM section is off
Off 0 Off
On 1 On
b RW S11RETENTION Keep retention on RAM section S11 when RAM section is off
Off 0 Off
On 1 On
c RW S12RETENTION Keep retention on RAM section S12 when RAM section is off
Off 0 Off
On 1 On
d RW S13RETENTION Keep retention on RAM section S13 when RAM section is off
Off 0 Off
On 1 On
e RW S14RETENTION Keep retention on RAM section S14 when RAM section is off
Off 0 Off
On 1 On
f RW S15RETENTION Keep retention on RAM section S15 when RAM section is off
Off 0 Off
On 1 On

5.3.7.31 RAM[3].POWERSET
Address offset: 0x934
RAM3 power control set register
When read, this register will return the value of the POWER register.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A W S0POWER Keep RAM section S0 of RAM3 on or off in System ON mode
On 1 On
B W S1POWER Keep RAM section S1 of RAM3 on or off in System ON mode
On 1 On
C W S2POWER Keep RAM section S2 of RAM3 on or off in System ON mode
On 1 On
D W S3POWER Keep RAM section S3 of RAM3 on or off in System ON mode
On 1 On
E W S4POWER Keep RAM section S4 of RAM3 on or off in System ON mode
On 1 On
F W S5POWER Keep RAM section S5 of RAM3 on or off in System ON mode
On 1 On
G W S6POWER Keep RAM section S6 of RAM3 on or off in System ON mode
On 1 On
H W S7POWER Keep RAM section S7 of RAM3 on or off in System ON mode

4413_417 v1.9 120

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
On 1 On
I W S8POWER Keep RAM section S8 of RAM3 on or off in System ON mode
On 1 On
J W S9POWER Keep RAM section S9 of RAM3 on or off in System ON mode
On 1 On
K W S10POWER Keep RAM section S10 of RAM3 on or off in System ON mode
On 1 On
L W S11POWER Keep RAM section S11 of RAM3 on or off in System ON mode
On 1 On
M W S12POWER Keep RAM section S12 of RAM3 on or off in System ON mode
On 1 On
N W S13POWER Keep RAM section S13 of RAM3 on or off in System ON mode
On 1 On
O W S14POWER Keep RAM section S14 of RAM3 on or off in System ON mode
On 1 On
P W S15POWER Keep RAM section S15 of RAM3 on or off in System ON mode
On 1 On
Q W S0RETENTION Keep retention on RAM section S0 when RAM section is switched off
On 1 On
R W S1RETENTION Keep retention on RAM section S1 when RAM section is switched off
On 1 On
S W S2RETENTION Keep retention on RAM section S2 when RAM section is switched off
On 1 On
T W S3RETENTION Keep retention on RAM section S3 when RAM section is switched off
On 1 On
U W S4RETENTION Keep retention on RAM section S4 when RAM section is switched off
On 1 On
V W S5RETENTION Keep retention on RAM section S5 when RAM section is switched off
On 1 On
W W S6RETENTION Keep retention on RAM section S6 when RAM section is switched off
On 1 On
X W S7RETENTION Keep retention on RAM section S7 when RAM section is switched off
On 1 On
Y W S8RETENTION Keep retention on RAM section S8 when RAM section is switched off
On 1 On
Z W S9RETENTION Keep retention on RAM section S9 when RAM section is switched off
On 1 On
a W S10RETENTION Keep retention on RAM section S10 when RAM section is switched off
On 1 On
b W S11RETENTION Keep retention on RAM section S11 when RAM section is switched off
On 1 On
c W S12RETENTION Keep retention on RAM section S12 when RAM section is switched off
On 1 On
d W S13RETENTION Keep retention on RAM section S13 when RAM section is switched off
On 1 On
e W S14RETENTION Keep retention on RAM section S14 when RAM section is switched off
On 1 On
f W S15RETENTION Keep retention on RAM section S15 when RAM section is switched off
On 1 On

4413_417 v1.9 121

 Power and clock management

5.3.7.32 RAM[3].POWERCLR
Address offset: 0x938
RAM3 power control clear register
When read, this register will return the value of the POWER register.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A W S0POWER Keep RAM section S0 of RAM3 on or off in System ON mode
Off 1 Off
B W S1POWER Keep RAM section S1 of RAM3 on or off in System ON mode
Off 1 Off
C W S2POWER Keep RAM section S2 of RAM3 on or off in System ON mode
Off 1 Off
D W S3POWER Keep RAM section S3 of RAM3 on or off in System ON mode
Off 1 Off
E W S4POWER Keep RAM section S4 of RAM3 on or off in System ON mode
Off 1 Off
F W S5POWER Keep RAM section S5 of RAM3 on or off in System ON mode
Off 1 Off
G W S6POWER Keep RAM section S6 of RAM3 on or off in System ON mode
Off 1 Off
H W S7POWER Keep RAM section S7 of RAM3 on or off in System ON mode
Off 1 Off
I W S8POWER Keep RAM section S8 of RAM3 on or off in System ON mode
Off 1 Off
J W S9POWER Keep RAM section S9 of RAM3 on or off in System ON mode
Off 1 Off
K W S10POWER Keep RAM section S10 of RAM3 on or off in System ON mode
Off 1 Off
L W S11POWER Keep RAM section S11 of RAM3 on or off in System ON mode
Off 1 Off
M W S12POWER Keep RAM section S12 of RAM3 on or off in System ON mode
Off 1 Off
N W S13POWER Keep RAM section S13 of RAM3 on or off in System ON mode
Off 1 Off
O W S14POWER Keep RAM section S14 of RAM3 on or off in System ON mode
Off 1 Off
P W S15POWER Keep RAM section S15 of RAM3 on or off in System ON mode
Off 1 Off
Q W S0RETENTION Keep retention on RAM section S0 when RAM section is switched off
Off 1 Off
R W S1RETENTION Keep retention on RAM section S1 when RAM section is switched off
Off 1 Off
S W S2RETENTION Keep retention on RAM section S2 when RAM section is switched off
Off 1 Off
T W S3RETENTION Keep retention on RAM section S3 when RAM section is switched off
Off 1 Off
U W S4RETENTION Keep retention on RAM section S4 when RAM section is switched off
Off 1 Off
V W S5RETENTION Keep retention on RAM section S5 when RAM section is switched off

4413_417 v1.9 122

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
Off 1 Off
W W S6RETENTION Keep retention on RAM section S6 when RAM section is switched off
Off 1 Off
X W S7RETENTION Keep retention on RAM section S7 when RAM section is switched off
Off 1 Off
Y W S8RETENTION Keep retention on RAM section S8 when RAM section is switched off
Off 1 Off
Z W S9RETENTION Keep retention on RAM section S9 when RAM section is switched off
Off 1 Off
a W S10RETENTION Keep retention on RAM section S10 when RAM section is switched off
Off 1 Off
b W S11RETENTION Keep retention on RAM section S11 when RAM section is switched off
Off 1 Off
c W S12RETENTION Keep retention on RAM section S12 when RAM section is switched off
Off 1 Off
d W S13RETENTION Keep retention on RAM section S13 when RAM section is switched off
Off 1 Off
e W S14RETENTION Keep retention on RAM section S14 when RAM section is switched off
Off 1 Off
f W S15RETENTION Keep retention on RAM section S15 when RAM section is switched off
Off 1 Off

5.3.7.33 RAM[4].POWER
Address offset: 0x940
RAM4 power control register

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW S0POWER Keep RAM section S0 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S0RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
B RW S1POWER Keep RAM section S1 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S1RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
C RW S2POWER Keep RAM section S2 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S2RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off

4413_417 v1.9 123

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
On 1 On
D RW S3POWER Keep RAM section S3 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S3RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
E RW S4POWER Keep RAM section S4 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S4RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
F RW S5POWER Keep RAM section S5 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S5RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
G RW S6POWER Keep RAM section S6 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S6RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
H RW S7POWER Keep RAM section S7 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S7RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
I RW S8POWER Keep RAM section S8 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S8RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
J RW S9POWER Keep RAM section S9 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S9RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
K RW S10POWER Keep RAM section S10 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S10RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off

4413_417 v1.9 124

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
On 1 On
L RW S11POWER Keep RAM section S11 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S11RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
M RW S12POWER Keep RAM section S12 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S12RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
N RW S13POWER Keep RAM section S13 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S13RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
O RW S14POWER Keep RAM section S14 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S14RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
P RW S15POWER Keep RAM section S15 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S15RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
Q RW S0RETENTION Keep retention on RAM section S0 when RAM section is off
Off 0 Off
On 1 On
R RW S1RETENTION Keep retention on RAM section S1 when RAM section is off
Off 0 Off
On 1 On
S RW S2RETENTION Keep retention on RAM section S2 when RAM section is off
Off 0 Off
On 1 On
T RW S3RETENTION Keep retention on RAM section S3 when RAM section is off
Off 0 Off
On 1 On
U RW S4RETENTION Keep retention on RAM section S4 when RAM section is off
Off 0 Off
On 1 On
V RW S5RETENTION Keep retention on RAM section S5 when RAM section is off
Off 0 Off
On 1 On

4413_417 v1.9 125

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
W RW S6RETENTION Keep retention on RAM section S6 when RAM section is off
Off 0 Off
On 1 On
X RW S7RETENTION Keep retention on RAM section S7 when RAM section is off
Off 0 Off
On 1 On
Y RW S8RETENTION Keep retention on RAM section S8 when RAM section is off
Off 0 Off
On 1 On
Z RW S9RETENTION Keep retention on RAM section S9 when RAM section is off
Off 0 Off
On 1 On
a RW S10RETENTION Keep retention on RAM section S10 when RAM section is off
Off 0 Off
On 1 On
b RW S11RETENTION Keep retention on RAM section S11 when RAM section is off
Off 0 Off
On 1 On
c RW S12RETENTION Keep retention on RAM section S12 when RAM section is off
Off 0 Off
On 1 On
d RW S13RETENTION Keep retention on RAM section S13 when RAM section is off
Off 0 Off
On 1 On
e RW S14RETENTION Keep retention on RAM section S14 when RAM section is off
Off 0 Off
On 1 On
f RW S15RETENTION Keep retention on RAM section S15 when RAM section is off
Off 0 Off
On 1 On

5.3.7.34 RAM[4].POWERSET
Address offset: 0x944
RAM4 power control set register
When read, this register will return the value of the POWER register.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A W S0POWER Keep RAM section S0 of RAM4 on or off in System ON mode
On 1 On
B W S1POWER Keep RAM section S1 of RAM4 on or off in System ON mode
On 1 On
C W S2POWER Keep RAM section S2 of RAM4 on or off in System ON mode
On 1 On
D W S3POWER Keep RAM section S3 of RAM4 on or off in System ON mode
On 1 On

4413_417 v1.9 126

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
E W S4POWER Keep RAM section S4 of RAM4 on or off in System ON mode
On 1 On
F W S5POWER Keep RAM section S5 of RAM4 on or off in System ON mode
On 1 On
G W S6POWER Keep RAM section S6 of RAM4 on or off in System ON mode
On 1 On
H W S7POWER Keep RAM section S7 of RAM4 on or off in System ON mode
On 1 On
I W S8POWER Keep RAM section S8 of RAM4 on or off in System ON mode
On 1 On
J W S9POWER Keep RAM section S9 of RAM4 on or off in System ON mode
On 1 On
K W S10POWER Keep RAM section S10 of RAM4 on or off in System ON mode
On 1 On
L W S11POWER Keep RAM section S11 of RAM4 on or off in System ON mode
On 1 On
M W S12POWER Keep RAM section S12 of RAM4 on or off in System ON mode
On 1 On
N W S13POWER Keep RAM section S13 of RAM4 on or off in System ON mode
On 1 On
O W S14POWER Keep RAM section S14 of RAM4 on or off in System ON mode
On 1 On
P W S15POWER Keep RAM section S15 of RAM4 on or off in System ON mode
On 1 On
Q W S0RETENTION Keep retention on RAM section S0 when RAM section is switched off
On 1 On
R W S1RETENTION Keep retention on RAM section S1 when RAM section is switched off
On 1 On
S W S2RETENTION Keep retention on RAM section S2 when RAM section is switched off
On 1 On
T W S3RETENTION Keep retention on RAM section S3 when RAM section is switched off
On 1 On
U W S4RETENTION Keep retention on RAM section S4 when RAM section is switched off
On 1 On
V W S5RETENTION Keep retention on RAM section S5 when RAM section is switched off
On 1 On
W W S6RETENTION Keep retention on RAM section S6 when RAM section is switched off
On 1 On
X W S7RETENTION Keep retention on RAM section S7 when RAM section is switched off
On 1 On
Y W S8RETENTION Keep retention on RAM section S8 when RAM section is switched off
On 1 On
Z W S9RETENTION Keep retention on RAM section S9 when RAM section is switched off
On 1 On
a W S10RETENTION Keep retention on RAM section S10 when RAM section is switched off
On 1 On
b W S11RETENTION Keep retention on RAM section S11 when RAM section is switched off
On 1 On
c W S12RETENTION Keep retention on RAM section S12 when RAM section is switched off
On 1 On

4413_417 v1.9 127

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
d W S13RETENTION Keep retention on RAM section S13 when RAM section is switched off
On 1 On
e W S14RETENTION Keep retention on RAM section S14 when RAM section is switched off
On 1 On
f W S15RETENTION Keep retention on RAM section S15 when RAM section is switched off
On 1 On

5.3.7.35 RAM[4].POWERCLR
Address offset: 0x948
RAM4 power control clear register
When read, this register will return the value of the POWER register.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A W S0POWER Keep RAM section S0 of RAM4 on or off in System ON mode
Off 1 Off
B W S1POWER Keep RAM section S1 of RAM4 on or off in System ON mode
Off 1 Off
C W S2POWER Keep RAM section S2 of RAM4 on or off in System ON mode
Off 1 Off
D W S3POWER Keep RAM section S3 of RAM4 on or off in System ON mode
Off 1 Off
E W S4POWER Keep RAM section S4 of RAM4 on or off in System ON mode
Off 1 Off
F W S5POWER Keep RAM section S5 of RAM4 on or off in System ON mode
Off 1 Off
G W S6POWER Keep RAM section S6 of RAM4 on or off in System ON mode
Off 1 Off
H W S7POWER Keep RAM section S7 of RAM4 on or off in System ON mode
Off 1 Off
I W S8POWER Keep RAM section S8 of RAM4 on or off in System ON mode
Off 1 Off
J W S9POWER Keep RAM section S9 of RAM4 on or off in System ON mode
Off 1 Off
K W S10POWER Keep RAM section S10 of RAM4 on or off in System ON mode
Off 1 Off
L W S11POWER Keep RAM section S11 of RAM4 on or off in System ON mode
Off 1 Off
M W S12POWER Keep RAM section S12 of RAM4 on or off in System ON mode
Off 1 Off
N W S13POWER Keep RAM section S13 of RAM4 on or off in System ON mode
Off 1 Off
O W S14POWER Keep RAM section S14 of RAM4 on or off in System ON mode
Off 1 Off
P W S15POWER Keep RAM section S15 of RAM4 on or off in System ON mode
Off 1 Off

4413_417 v1.9 128

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
Q W S0RETENTION Keep retention on RAM section S0 when RAM section is switched off
Off 1 Off
R W S1RETENTION Keep retention on RAM section S1 when RAM section is switched off
Off 1 Off
S W S2RETENTION Keep retention on RAM section S2 when RAM section is switched off
Off 1 Off
T W S3RETENTION Keep retention on RAM section S3 when RAM section is switched off
Off 1 Off
U W S4RETENTION Keep retention on RAM section S4 when RAM section is switched off
Off 1 Off
V W S5RETENTION Keep retention on RAM section S5 when RAM section is switched off
Off 1 Off
W W S6RETENTION Keep retention on RAM section S6 when RAM section is switched off
Off 1 Off
X W S7RETENTION Keep retention on RAM section S7 when RAM section is switched off
Off 1 Off
Y W S8RETENTION Keep retention on RAM section S8 when RAM section is switched off
Off 1 Off
Z W S9RETENTION Keep retention on RAM section S9 when RAM section is switched off
Off 1 Off
a W S10RETENTION Keep retention on RAM section S10 when RAM section is switched off
Off 1 Off
b W S11RETENTION Keep retention on RAM section S11 when RAM section is switched off
Off 1 Off
c W S12RETENTION Keep retention on RAM section S12 when RAM section is switched off
Off 1 Off
d W S13RETENTION Keep retention on RAM section S13 when RAM section is switched off
Off 1 Off
e W S14RETENTION Keep retention on RAM section S14 when RAM section is switched off
Off 1 Off
f W S15RETENTION Keep retention on RAM section S15 when RAM section is switched off
Off 1 Off

5.3.7.36 RAM[5].POWER
Address offset: 0x950
RAM5 power control register

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW S0POWER Keep RAM section S0 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S0RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On

4413_417 v1.9 129

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
B RW S1POWER Keep RAM section S1 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S1RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
C RW S2POWER Keep RAM section S2 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S2RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
D RW S3POWER Keep RAM section S3 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S3RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
E RW S4POWER Keep RAM section S4 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S4RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
F RW S5POWER Keep RAM section S5 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S5RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
G RW S6POWER Keep RAM section S6 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S6RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
H RW S7POWER Keep RAM section S7 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S7RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
I RW S8POWER Keep RAM section S8 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S8RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On

4413_417 v1.9 130

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
J RW S9POWER Keep RAM section S9 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S9RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
K RW S10POWER Keep RAM section S10 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S10RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
L RW S11POWER Keep RAM section S11 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S11RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
M RW S12POWER Keep RAM section S12 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S12RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
N RW S13POWER Keep RAM section S13 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S13RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
O RW S14POWER Keep RAM section S14 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S14RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
P RW S15POWER Keep RAM section S15 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S15RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
Q RW S0RETENTION Keep retention on RAM section S0 when RAM section is off
Off 0 Off
On 1 On
R RW S1RETENTION Keep retention on RAM section S1 when RAM section is off
Off 0 Off
On 1 On

4413_417 v1.9 131

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
S RW S2RETENTION Keep retention on RAM section S2 when RAM section is off
Off 0 Off
On 1 On
T RW S3RETENTION Keep retention on RAM section S3 when RAM section is off
Off 0 Off
On 1 On
U RW S4RETENTION Keep retention on RAM section S4 when RAM section is off
Off 0 Off
On 1 On
V RW S5RETENTION Keep retention on RAM section S5 when RAM section is off
Off 0 Off
On 1 On
W RW S6RETENTION Keep retention on RAM section S6 when RAM section is off
Off 0 Off
On 1 On
X RW S7RETENTION Keep retention on RAM section S7 when RAM section is off
Off 0 Off
On 1 On
Y RW S8RETENTION Keep retention on RAM section S8 when RAM section is off
Off 0 Off
On 1 On
Z RW S9RETENTION Keep retention on RAM section S9 when RAM section is off
Off 0 Off
On 1 On
a RW S10RETENTION Keep retention on RAM section S10 when RAM section is off
Off 0 Off
On 1 On
b RW S11RETENTION Keep retention on RAM section S11 when RAM section is off
Off 0 Off
On 1 On
c RW S12RETENTION Keep retention on RAM section S12 when RAM section is off
Off 0 Off
On 1 On
d RW S13RETENTION Keep retention on RAM section S13 when RAM section is off
Off 0 Off
On 1 On
e RW S14RETENTION Keep retention on RAM section S14 when RAM section is off
Off 0 Off
On 1 On
f RW S15RETENTION Keep retention on RAM section S15 when RAM section is off
Off 0 Off
On 1 On

5.3.7.37 RAM[5].POWERSET
Address offset: 0x954
RAM5 power control set register
When read, this register will return the value of the POWER register.

4413_417 v1.9 132

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A W S0POWER Keep RAM section S0 of RAM5 on or off in System ON mode
On 1 On
B W S1POWER Keep RAM section S1 of RAM5 on or off in System ON mode
On 1 On
C W S2POWER Keep RAM section S2 of RAM5 on or off in System ON mode
On 1 On
D W S3POWER Keep RAM section S3 of RAM5 on or off in System ON mode
On 1 On
E W S4POWER Keep RAM section S4 of RAM5 on or off in System ON mode
On 1 On
F W S5POWER Keep RAM section S5 of RAM5 on or off in System ON mode
On 1 On
G W S6POWER Keep RAM section S6 of RAM5 on or off in System ON mode
On 1 On
H W S7POWER Keep RAM section S7 of RAM5 on or off in System ON mode
On 1 On
I W S8POWER Keep RAM section S8 of RAM5 on or off in System ON mode
On 1 On
J W S9POWER Keep RAM section S9 of RAM5 on or off in System ON mode
On 1 On
K W S10POWER Keep RAM section S10 of RAM5 on or off in System ON mode
On 1 On
L W S11POWER Keep RAM section S11 of RAM5 on or off in System ON mode
On 1 On
M W S12POWER Keep RAM section S12 of RAM5 on or off in System ON mode
On 1 On
N W S13POWER Keep RAM section S13 of RAM5 on or off in System ON mode
On 1 On
O W S14POWER Keep RAM section S14 of RAM5 on or off in System ON mode
On 1 On
P W S15POWER Keep RAM section S15 of RAM5 on or off in System ON mode
On 1 On
Q W S0RETENTION Keep retention on RAM section S0 when RAM section is switched off
On 1 On
R W S1RETENTION Keep retention on RAM section S1 when RAM section is switched off
On 1 On
S W S2RETENTION Keep retention on RAM section S2 when RAM section is switched off
On 1 On
T W S3RETENTION Keep retention on RAM section S3 when RAM section is switched off
On 1 On
U W S4RETENTION Keep retention on RAM section S4 when RAM section is switched off
On 1 On
V W S5RETENTION Keep retention on RAM section S5 when RAM section is switched off
On 1 On
W W S6RETENTION Keep retention on RAM section S6 when RAM section is switched off
On 1 On
X W S7RETENTION Keep retention on RAM section S7 when RAM section is switched off
On 1 On
Y W S8RETENTION Keep retention on RAM section S8 when RAM section is switched off
On 1 On

4413_417 v1.9 133

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
Z W S9RETENTION Keep retention on RAM section S9 when RAM section is switched off
On 1 On
a W S10RETENTION Keep retention on RAM section S10 when RAM section is switched off
On 1 On
b W S11RETENTION Keep retention on RAM section S11 when RAM section is switched off
On 1 On
c W S12RETENTION Keep retention on RAM section S12 when RAM section is switched off
On 1 On
d W S13RETENTION Keep retention on RAM section S13 when RAM section is switched off
On 1 On
e W S14RETENTION Keep retention on RAM section S14 when RAM section is switched off
On 1 On
f W S15RETENTION Keep retention on RAM section S15 when RAM section is switched off
On 1 On

5.3.7.38 RAM[5].POWERCLR
Address offset: 0x958
RAM5 power control clear register
When read, this register will return the value of the POWER register.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A W S0POWER Keep RAM section S0 of RAM5 on or off in System ON mode
Off 1 Off
B W S1POWER Keep RAM section S1 of RAM5 on or off in System ON mode
Off 1 Off
C W S2POWER Keep RAM section S2 of RAM5 on or off in System ON mode
Off 1 Off
D W S3POWER Keep RAM section S3 of RAM5 on or off in System ON mode
Off 1 Off
E W S4POWER Keep RAM section S4 of RAM5 on or off in System ON mode
Off 1 Off
F W S5POWER Keep RAM section S5 of RAM5 on or off in System ON mode
Off 1 Off
G W S6POWER Keep RAM section S6 of RAM5 on or off in System ON mode
Off 1 Off
H W S7POWER Keep RAM section S7 of RAM5 on or off in System ON mode
Off 1 Off
I W S8POWER Keep RAM section S8 of RAM5 on or off in System ON mode
Off 1 Off
J W S9POWER Keep RAM section S9 of RAM5 on or off in System ON mode
Off 1 Off
K W S10POWER Keep RAM section S10 of RAM5 on or off in System ON mode
Off 1 Off
L W S11POWER Keep RAM section S11 of RAM5 on or off in System ON mode
Off 1 Off

4413_417 v1.9 134

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
M W S12POWER Keep RAM section S12 of RAM5 on or off in System ON mode
Off 1 Off
N W S13POWER Keep RAM section S13 of RAM5 on or off in System ON mode
Off 1 Off
O W S14POWER Keep RAM section S14 of RAM5 on or off in System ON mode
Off 1 Off
P W S15POWER Keep RAM section S15 of RAM5 on or off in System ON mode
Off 1 Off
Q W S0RETENTION Keep retention on RAM section S0 when RAM section is switched off
Off 1 Off
R W S1RETENTION Keep retention on RAM section S1 when RAM section is switched off
Off 1 Off
S W S2RETENTION Keep retention on RAM section S2 when RAM section is switched off
Off 1 Off
T W S3RETENTION Keep retention on RAM section S3 when RAM section is switched off
Off 1 Off
U W S4RETENTION Keep retention on RAM section S4 when RAM section is switched off
Off 1 Off
V W S5RETENTION Keep retention on RAM section S5 when RAM section is switched off
Off 1 Off
W W S6RETENTION Keep retention on RAM section S6 when RAM section is switched off
Off 1 Off
X W S7RETENTION Keep retention on RAM section S7 when RAM section is switched off
Off 1 Off
Y W S8RETENTION Keep retention on RAM section S8 when RAM section is switched off
Off 1 Off
Z W S9RETENTION Keep retention on RAM section S9 when RAM section is switched off
Off 1 Off
a W S10RETENTION Keep retention on RAM section S10 when RAM section is switched off
Off 1 Off
b W S11RETENTION Keep retention on RAM section S11 when RAM section is switched off
Off 1 Off
c W S12RETENTION Keep retention on RAM section S12 when RAM section is switched off
Off 1 Off
d W S13RETENTION Keep retention on RAM section S13 when RAM section is switched off
Off 1 Off
e W S14RETENTION Keep retention on RAM section S14 when RAM section is switched off
Off 1 Off
f W S15RETENTION Keep retention on RAM section S15 when RAM section is switched off
Off 1 Off

5.3.7.39 RAM[6].POWER
Address offset: 0x960
RAM6 power control register

4413_417 v1.9 135

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW S0POWER Keep RAM section S0 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S0RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
B RW S1POWER Keep RAM section S1 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S1RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
C RW S2POWER Keep RAM section S2 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S2RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
D RW S3POWER Keep RAM section S3 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S3RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
E RW S4POWER Keep RAM section S4 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S4RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
F RW S5POWER Keep RAM section S5 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S5RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
G RW S6POWER Keep RAM section S6 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S6RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
H RW S7POWER Keep RAM section S7 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S7RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On

4413_417 v1.9 136

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
I RW S8POWER Keep RAM section S8 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S8RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
J RW S9POWER Keep RAM section S9 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S9RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
K RW S10POWER Keep RAM section S10 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S10RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
L RW S11POWER Keep RAM section S11 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S11RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
M RW S12POWER Keep RAM section S12 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S12RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
N RW S13POWER Keep RAM section S13 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S13RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
O RW S14POWER Keep RAM section S14 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S14RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
P RW S15POWER Keep RAM section S15 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S15RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On

4413_417 v1.9 137

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
Q RW S0RETENTION Keep retention on RAM section S0 when RAM section is off
Off 0 Off
On 1 On
R RW S1RETENTION Keep retention on RAM section S1 when RAM section is off
Off 0 Off
On 1 On
S RW S2RETENTION Keep retention on RAM section S2 when RAM section is off
Off 0 Off
On 1 On
T RW S3RETENTION Keep retention on RAM section S3 when RAM section is off
Off 0 Off
On 1 On
U RW S4RETENTION Keep retention on RAM section S4 when RAM section is off
Off 0 Off
On 1 On
V RW S5RETENTION Keep retention on RAM section S5 when RAM section is off
Off 0 Off
On 1 On
W RW S6RETENTION Keep retention on RAM section S6 when RAM section is off
Off 0 Off
On 1 On
X RW S7RETENTION Keep retention on RAM section S7 when RAM section is off
Off 0 Off
On 1 On
Y RW S8RETENTION Keep retention on RAM section S8 when RAM section is off
Off 0 Off
On 1 On
Z RW S9RETENTION Keep retention on RAM section S9 when RAM section is off
Off 0 Off
On 1 On
a RW S10RETENTION Keep retention on RAM section S10 when RAM section is off
Off 0 Off
On 1 On
b RW S11RETENTION Keep retention on RAM section S11 when RAM section is off
Off 0 Off
On 1 On
c RW S12RETENTION Keep retention on RAM section S12 when RAM section is off
Off 0 Off
On 1 On
d RW S13RETENTION Keep retention on RAM section S13 when RAM section is off
Off 0 Off
On 1 On
e RW S14RETENTION Keep retention on RAM section S14 when RAM section is off
Off 0 Off
On 1 On
f RW S15RETENTION Keep retention on RAM section S15 when RAM section is off
Off 0 Off
On 1 On

4413_417 v1.9 138

 Power and clock management

5.3.7.40 RAM[6].POWERSET
Address offset: 0x964
RAM6 power control set register
When read, this register will return the value of the POWER register.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A W S0POWER Keep RAM section S0 of RAM6 on or off in System ON mode
On 1 On
B W S1POWER Keep RAM section S1 of RAM6 on or off in System ON mode
On 1 On
C W S2POWER Keep RAM section S2 of RAM6 on or off in System ON mode
On 1 On
D W S3POWER Keep RAM section S3 of RAM6 on or off in System ON mode
On 1 On
E W S4POWER Keep RAM section S4 of RAM6 on or off in System ON mode
On 1 On
F W S5POWER Keep RAM section S5 of RAM6 on or off in System ON mode
On 1 On
G W S6POWER Keep RAM section S6 of RAM6 on or off in System ON mode
On 1 On
H W S7POWER Keep RAM section S7 of RAM6 on or off in System ON mode
On 1 On
I W S8POWER Keep RAM section S8 of RAM6 on or off in System ON mode
On 1 On
J W S9POWER Keep RAM section S9 of RAM6 on or off in System ON mode
On 1 On
K W S10POWER Keep RAM section S10 of RAM6 on or off in System ON mode
On 1 On
L W S11POWER Keep RAM section S11 of RAM6 on or off in System ON mode
On 1 On
M W S12POWER Keep RAM section S12 of RAM6 on or off in System ON mode
On 1 On
N W S13POWER Keep RAM section S13 of RAM6 on or off in System ON mode
On 1 On
O W S14POWER Keep RAM section S14 of RAM6 on or off in System ON mode
On 1 On
P W S15POWER Keep RAM section S15 of RAM6 on or off in System ON mode
On 1 On
Q W S0RETENTION Keep retention on RAM section S0 when RAM section is switched off
On 1 On
R W S1RETENTION Keep retention on RAM section S1 when RAM section is switched off
On 1 On
S W S2RETENTION Keep retention on RAM section S2 when RAM section is switched off
On 1 On
T W S3RETENTION Keep retention on RAM section S3 when RAM section is switched off
On 1 On
U W S4RETENTION Keep retention on RAM section S4 when RAM section is switched off
On 1 On
V W S5RETENTION Keep retention on RAM section S5 when RAM section is switched off

4413_417 v1.9 139

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
On 1 On
W W S6RETENTION Keep retention on RAM section S6 when RAM section is switched off
On 1 On
X W S7RETENTION Keep retention on RAM section S7 when RAM section is switched off
On 1 On
Y W S8RETENTION Keep retention on RAM section S8 when RAM section is switched off
On 1 On
Z W S9RETENTION Keep retention on RAM section S9 when RAM section is switched off
On 1 On
a W S10RETENTION Keep retention on RAM section S10 when RAM section is switched off
On 1 On
b W S11RETENTION Keep retention on RAM section S11 when RAM section is switched off
On 1 On
c W S12RETENTION Keep retention on RAM section S12 when RAM section is switched off
On 1 On
d W S13RETENTION Keep retention on RAM section S13 when RAM section is switched off
On 1 On
e W S14RETENTION Keep retention on RAM section S14 when RAM section is switched off
On 1 On
f W S15RETENTION Keep retention on RAM section S15 when RAM section is switched off
On 1 On

5.3.7.41 RAM[6].POWERCLR
Address offset: 0x968
RAM6 power control clear register
When read, this register will return the value of the POWER register.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A W S0POWER Keep RAM section S0 of RAM6 on or off in System ON mode
Off 1 Off
B W S1POWER Keep RAM section S1 of RAM6 on or off in System ON mode
Off 1 Off
C W S2POWER Keep RAM section S2 of RAM6 on or off in System ON mode
Off 1 Off
D W S3POWER Keep RAM section S3 of RAM6 on or off in System ON mode
Off 1 Off
E W S4POWER Keep RAM section S4 of RAM6 on or off in System ON mode
Off 1 Off
F W S5POWER Keep RAM section S5 of RAM6 on or off in System ON mode
Off 1 Off
G W S6POWER Keep RAM section S6 of RAM6 on or off in System ON mode
Off 1 Off
H W S7POWER Keep RAM section S7 of RAM6 on or off in System ON mode
Off 1 Off
I W S8POWER Keep RAM section S8 of RAM6 on or off in System ON mode

4413_417 v1.9 140

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
Off 1 Off
J W S9POWER Keep RAM section S9 of RAM6 on or off in System ON mode
Off 1 Off
K W S10POWER Keep RAM section S10 of RAM6 on or off in System ON mode
Off 1 Off
L W S11POWER Keep RAM section S11 of RAM6 on or off in System ON mode
Off 1 Off
M W S12POWER Keep RAM section S12 of RAM6 on or off in System ON mode
Off 1 Off
N W S13POWER Keep RAM section S13 of RAM6 on or off in System ON mode
Off 1 Off
O W S14POWER Keep RAM section S14 of RAM6 on or off in System ON mode
Off 1 Off
P W S15POWER Keep RAM section S15 of RAM6 on or off in System ON mode
Off 1 Off
Q W S0RETENTION Keep retention on RAM section S0 when RAM section is switched off
Off 1 Off
R W S1RETENTION Keep retention on RAM section S1 when RAM section is switched off
Off 1 Off
S W S2RETENTION Keep retention on RAM section S2 when RAM section is switched off
Off 1 Off
T W S3RETENTION Keep retention on RAM section S3 when RAM section is switched off
Off 1 Off
U W S4RETENTION Keep retention on RAM section S4 when RAM section is switched off
Off 1 Off
V W S5RETENTION Keep retention on RAM section S5 when RAM section is switched off
Off 1 Off
W W S6RETENTION Keep retention on RAM section S6 when RAM section is switched off
Off 1 Off
X W S7RETENTION Keep retention on RAM section S7 when RAM section is switched off
Off 1 Off
Y W S8RETENTION Keep retention on RAM section S8 when RAM section is switched off
Off 1 Off
Z W S9RETENTION Keep retention on RAM section S9 when RAM section is switched off
Off 1 Off
a W S10RETENTION Keep retention on RAM section S10 when RAM section is switched off
Off 1 Off
b W S11RETENTION Keep retention on RAM section S11 when RAM section is switched off
Off 1 Off
c W S12RETENTION Keep retention on RAM section S12 when RAM section is switched off
Off 1 Off
d W S13RETENTION Keep retention on RAM section S13 when RAM section is switched off
Off 1 Off
e W S14RETENTION Keep retention on RAM section S14 when RAM section is switched off
Off 1 Off
f W S15RETENTION Keep retention on RAM section S15 when RAM section is switched off
Off 1 Off

5.3.7.42 RAM[7].POWER
Address offset: 0x970

4413_417 v1.9 141

 Power and clock management

RAM7 power control register

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A
Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW S0POWER Keep RAM section S0 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S0RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
B RW S1POWER Keep RAM section S1 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S1RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
C RW S2POWER Keep RAM section S2 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S2RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
D RW S3POWER Keep RAM section S3 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S3RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
E RW S4POWER Keep RAM section S4 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S4RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
F RW S5POWER Keep RAM section S5 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S5RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
G RW S6POWER Keep RAM section S6 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S6RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On

4413_417 v1.9 142

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
H RW S7POWER Keep RAM section S7 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S7RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
I RW S8POWER Keep RAM section S8 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S8RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
J RW S9POWER Keep RAM section S9 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S9RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
K RW S10POWER Keep RAM section S10 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S10RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
L RW S11POWER Keep RAM section S11 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S11RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
M RW S12POWER Keep RAM section S12 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S12RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
N RW S13POWER Keep RAM section S13 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S13RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
O RW S14POWER Keep RAM section S14 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S14RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On

4413_417 v1.9 143

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
P RW S15POWER Keep RAM section S15 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S15RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
Q RW S0RETENTION Keep retention on RAM section S0 when RAM section is off
Off 0 Off
On 1 On
R RW S1RETENTION Keep retention on RAM section S1 when RAM section is off
Off 0 Off
On 1 On
S RW S2RETENTION Keep retention on RAM section S2 when RAM section is off
Off 0 Off
On 1 On
T RW S3RETENTION Keep retention on RAM section S3 when RAM section is off
Off 0 Off
On 1 On
U RW S4RETENTION Keep retention on RAM section S4 when RAM section is off
Off 0 Off
On 1 On
V RW S5RETENTION Keep retention on RAM section S5 when RAM section is off
Off 0 Off
On 1 On
W RW S6RETENTION Keep retention on RAM section S6 when RAM section is off
Off 0 Off
On 1 On
X RW S7RETENTION Keep retention on RAM section S7 when RAM section is off
Off 0 Off
On 1 On
Y RW S8RETENTION Keep retention on RAM section S8 when RAM section is off
Off 0 Off
On 1 On
Z RW S9RETENTION Keep retention on RAM section S9 when RAM section is off
Off 0 Off
On 1 On
a RW S10RETENTION Keep retention on RAM section S10 when RAM section is off
Off 0 Off
On 1 On
b RW S11RETENTION Keep retention on RAM section S11 when RAM section is off
Off 0 Off
On 1 On
c RW S12RETENTION Keep retention on RAM section S12 when RAM section is off
Off 0 Off
On 1 On
d RW S13RETENTION Keep retention on RAM section S13 when RAM section is off
Off 0 Off
On 1 On
e RW S14RETENTION Keep retention on RAM section S14 when RAM section is off
Off 0 Off

4413_417 v1.9 144

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
On 1 On
f RW S15RETENTION Keep retention on RAM section S15 when RAM section is off
Off 0 Off
On 1 On

5.3.7.43 RAM[7].POWERSET
Address offset: 0x974
RAM7 power control set register
When read, this register will return the value of the POWER register.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A W S0POWER Keep RAM section S0 of RAM7 on or off in System ON mode
On 1 On
B W S1POWER Keep RAM section S1 of RAM7 on or off in System ON mode
On 1 On
C W S2POWER Keep RAM section S2 of RAM7 on or off in System ON mode
On 1 On
D W S3POWER Keep RAM section S3 of RAM7 on or off in System ON mode
On 1 On
E W S4POWER Keep RAM section S4 of RAM7 on or off in System ON mode
On 1 On
F W S5POWER Keep RAM section S5 of RAM7 on or off in System ON mode
On 1 On
G W S6POWER Keep RAM section S6 of RAM7 on or off in System ON mode
On 1 On
H W S7POWER Keep RAM section S7 of RAM7 on or off in System ON mode
On 1 On
I W S8POWER Keep RAM section S8 of RAM7 on or off in System ON mode
On 1 On
J W S9POWER Keep RAM section S9 of RAM7 on or off in System ON mode
On 1 On
K W S10POWER Keep RAM section S10 of RAM7 on or off in System ON mode
On 1 On
L W S11POWER Keep RAM section S11 of RAM7 on or off in System ON mode
On 1 On
M W S12POWER Keep RAM section S12 of RAM7 on or off in System ON mode
On 1 On
N W S13POWER Keep RAM section S13 of RAM7 on or off in System ON mode
On 1 On
O W S14POWER Keep RAM section S14 of RAM7 on or off in System ON mode
On 1 On
P W S15POWER Keep RAM section S15 of RAM7 on or off in System ON mode
On 1 On
Q W S0RETENTION Keep retention on RAM section S0 when RAM section is switched off
On 1 On

4413_417 v1.9 145

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
R W S1RETENTION Keep retention on RAM section S1 when RAM section is switched off
On 1 On
S W S2RETENTION Keep retention on RAM section S2 when RAM section is switched off
On 1 On
T W S3RETENTION Keep retention on RAM section S3 when RAM section is switched off
On 1 On
U W S4RETENTION Keep retention on RAM section S4 when RAM section is switched off
On 1 On
V W S5RETENTION Keep retention on RAM section S5 when RAM section is switched off
On 1 On
W W S6RETENTION Keep retention on RAM section S6 when RAM section is switched off
On 1 On
X W S7RETENTION Keep retention on RAM section S7 when RAM section is switched off
On 1 On
Y W S8RETENTION Keep retention on RAM section S8 when RAM section is switched off
On 1 On
Z W S9RETENTION Keep retention on RAM section S9 when RAM section is switched off
On 1 On
a W S10RETENTION Keep retention on RAM section S10 when RAM section is switched off
On 1 On
b W S11RETENTION Keep retention on RAM section S11 when RAM section is switched off
On 1 On
c W S12RETENTION Keep retention on RAM section S12 when RAM section is switched off
On 1 On
d W S13RETENTION Keep retention on RAM section S13 when RAM section is switched off
On 1 On
e W S14RETENTION Keep retention on RAM section S14 when RAM section is switched off
On 1 On
f W S15RETENTION Keep retention on RAM section S15 when RAM section is switched off
On 1 On

5.3.7.44 RAM[7].POWERCLR
Address offset: 0x978
RAM7 power control clear register
When read, this register will return the value of the POWER register.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A W S0POWER Keep RAM section S0 of RAM7 on or off in System ON mode
Off 1 Off
B W S1POWER Keep RAM section S1 of RAM7 on or off in System ON mode
Off 1 Off
C W S2POWER Keep RAM section S2 of RAM7 on or off in System ON mode
Off 1 Off
D W S3POWER Keep RAM section S3 of RAM7 on or off in System ON mode
Off 1 Off

4413_417 v1.9 146

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
E W S4POWER Keep RAM section S4 of RAM7 on or off in System ON mode
Off 1 Off
F W S5POWER Keep RAM section S5 of RAM7 on or off in System ON mode
Off 1 Off
G W S6POWER Keep RAM section S6 of RAM7 on or off in System ON mode
Off 1 Off
H W S7POWER Keep RAM section S7 of RAM7 on or off in System ON mode
Off 1 Off
I W S8POWER Keep RAM section S8 of RAM7 on or off in System ON mode
Off 1 Off
J W S9POWER Keep RAM section S9 of RAM7 on or off in System ON mode
Off 1 Off
K W S10POWER Keep RAM section S10 of RAM7 on or off in System ON mode
Off 1 Off
L W S11POWER Keep RAM section S11 of RAM7 on or off in System ON mode
Off 1 Off
M W S12POWER Keep RAM section S12 of RAM7 on or off in System ON mode
Off 1 Off
N W S13POWER Keep RAM section S13 of RAM7 on or off in System ON mode
Off 1 Off
O W S14POWER Keep RAM section S14 of RAM7 on or off in System ON mode
Off 1 Off
P W S15POWER Keep RAM section S15 of RAM7 on or off in System ON mode
Off 1 Off
Q W S0RETENTION Keep retention on RAM section S0 when RAM section is switched off
Off 1 Off
R W S1RETENTION Keep retention on RAM section S1 when RAM section is switched off
Off 1 Off
S W S2RETENTION Keep retention on RAM section S2 when RAM section is switched off
Off 1 Off
T W S3RETENTION Keep retention on RAM section S3 when RAM section is switched off
Off 1 Off
U W S4RETENTION Keep retention on RAM section S4 when RAM section is switched off
Off 1 Off
V W S5RETENTION Keep retention on RAM section S5 when RAM section is switched off
Off 1 Off
W W S6RETENTION Keep retention on RAM section S6 when RAM section is switched off
Off 1 Off
X W S7RETENTION Keep retention on RAM section S7 when RAM section is switched off
Off 1 Off
Y W S8RETENTION Keep retention on RAM section S8 when RAM section is switched off
Off 1 Off
Z W S9RETENTION Keep retention on RAM section S9 when RAM section is switched off
Off 1 Off
a W S10RETENTION Keep retention on RAM section S10 when RAM section is switched off
Off 1 Off
b W S11RETENTION Keep retention on RAM section S11 when RAM section is switched off
Off 1 Off
c W S12RETENTION Keep retention on RAM section S12 when RAM section is switched off
Off 1 Off

4413_417 v1.9 147

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
d W S13RETENTION Keep retention on RAM section S13 when RAM section is switched off
Off 1 Off
e W S14RETENTION Keep retention on RAM section S14 when RAM section is switched off
Off 1 Off
f W S15RETENTION Keep retention on RAM section S15 when RAM section is switched off
Off 1 Off

5.3.7.45 RAM[8].POWER
Address offset: 0x980
RAM8 power control register

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW S0POWER Keep RAM section S0 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S0RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
B RW S1POWER Keep RAM section S1 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S1RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
C RW S2POWER Keep RAM section S2 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S2RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
D RW S3POWER Keep RAM section S3 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S3RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
E RW S4POWER Keep RAM section S4 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S4RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On

4413_417 v1.9 148

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
F RW S5POWER Keep RAM section S5 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S5RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
G RW S6POWER Keep RAM section S6 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S6RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
H RW S7POWER Keep RAM section S7 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S7RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
I RW S8POWER Keep RAM section S8 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S8RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
J RW S9POWER Keep RAM section S9 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S9RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
K RW S10POWER Keep RAM section S10 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S10RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
L RW S11POWER Keep RAM section S11 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S11RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
M RW S12POWER Keep RAM section S12 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S12RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On

4413_417 v1.9 149

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
N RW S13POWER Keep RAM section S13 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S13RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
O RW S14POWER Keep RAM section S14 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S14RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
P RW S15POWER Keep RAM section S15 on or off in System ON mode.

RAM sections are always retained when on, but can also be retained when
off depending on the settings in S15RETENTION. All RAM sections will be off
in System OFF mode.
Off 0 Off
On 1 On
Q RW S0RETENTION Keep retention on RAM section S0 when RAM section is off
Off 0 Off
On 1 On
R RW S1RETENTION Keep retention on RAM section S1 when RAM section is off
Off 0 Off
On 1 On
S RW S2RETENTION Keep retention on RAM section S2 when RAM section is off
Off 0 Off
On 1 On
T RW S3RETENTION Keep retention on RAM section S3 when RAM section is off
Off 0 Off
On 1 On
U RW S4RETENTION Keep retention on RAM section S4 when RAM section is off
Off 0 Off
On 1 On
V RW S5RETENTION Keep retention on RAM section S5 when RAM section is off
Off 0 Off
On 1 On
W RW S6RETENTION Keep retention on RAM section S6 when RAM section is off
Off 0 Off
On 1 On
X RW S7RETENTION Keep retention on RAM section S7 when RAM section is off
Off 0 Off
On 1 On
Y RW S8RETENTION Keep retention on RAM section S8 when RAM section is off
Off 0 Off
On 1 On
Z RW S9RETENTION Keep retention on RAM section S9 when RAM section is off
Off 0 Off
On 1 On
a RW S10RETENTION Keep retention on RAM section S10 when RAM section is off

4413_417 v1.9 150

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
Off 0 Off
On 1 On
b RW S11RETENTION Keep retention on RAM section S11 when RAM section is off
Off 0 Off
On 1 On
c RW S12RETENTION Keep retention on RAM section S12 when RAM section is off
Off 0 Off
On 1 On
d RW S13RETENTION Keep retention on RAM section S13 when RAM section is off
Off 0 Off
On 1 On
e RW S14RETENTION Keep retention on RAM section S14 when RAM section is off
Off 0 Off
On 1 On
f RW S15RETENTION Keep retention on RAM section S15 when RAM section is off
Off 0 Off
On 1 On

5.3.7.46 RAM[8].POWERSET
Address offset: 0x984
RAM8 power control set register
When read, this register will return the value of the POWER register.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A W S0POWER Keep RAM section S0 of RAM8 on or off in System ON mode
On 1 On
B W S1POWER Keep RAM section S1 of RAM8 on or off in System ON mode
On 1 On
C W S2POWER Keep RAM section S2 of RAM8 on or off in System ON mode
On 1 On
D W S3POWER Keep RAM section S3 of RAM8 on or off in System ON mode
On 1 On
E W S4POWER Keep RAM section S4 of RAM8 on or off in System ON mode
On 1 On
F W S5POWER Keep RAM section S5 of RAM8 on or off in System ON mode
On 1 On
G W S6POWER Keep RAM section S6 of RAM8 on or off in System ON mode
On 1 On
H W S7POWER Keep RAM section S7 of RAM8 on or off in System ON mode
On 1 On
I W S8POWER Keep RAM section S8 of RAM8 on or off in System ON mode
On 1 On
J W S9POWER Keep RAM section S9 of RAM8 on or off in System ON mode
On 1 On
K W S10POWER Keep RAM section S10 of RAM8 on or off in System ON mode

4413_417 v1.9 151

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
On 1 On
L W S11POWER Keep RAM section S11 of RAM8 on or off in System ON mode
On 1 On
M W S12POWER Keep RAM section S12 of RAM8 on or off in System ON mode
On 1 On
N W S13POWER Keep RAM section S13 of RAM8 on or off in System ON mode
On 1 On
O W S14POWER Keep RAM section S14 of RAM8 on or off in System ON mode
On 1 On
P W S15POWER Keep RAM section S15 of RAM8 on or off in System ON mode
On 1 On
Q W S0RETENTION Keep retention on RAM section S0 when RAM section is switched off
On 1 On
R W S1RETENTION Keep retention on RAM section S1 when RAM section is switched off
On 1 On
S W S2RETENTION Keep retention on RAM section S2 when RAM section is switched off
On 1 On
T W S3RETENTION Keep retention on RAM section S3 when RAM section is switched off
On 1 On
U W S4RETENTION Keep retention on RAM section S4 when RAM section is switched off
On 1 On
V W S5RETENTION Keep retention on RAM section S5 when RAM section is switched off
On 1 On
W W S6RETENTION Keep retention on RAM section S6 when RAM section is switched off
On 1 On
X W S7RETENTION Keep retention on RAM section S7 when RAM section is switched off
On 1 On
Y W S8RETENTION Keep retention on RAM section S8 when RAM section is switched off
On 1 On
Z W S9RETENTION Keep retention on RAM section S9 when RAM section is switched off
On 1 On
a W S10RETENTION Keep retention on RAM section S10 when RAM section is switched off
On 1 On
b W S11RETENTION Keep retention on RAM section S11 when RAM section is switched off
On 1 On
c W S12RETENTION Keep retention on RAM section S12 when RAM section is switched off
On 1 On
d W S13RETENTION Keep retention on RAM section S13 when RAM section is switched off
On 1 On
e W S14RETENTION Keep retention on RAM section S14 when RAM section is switched off
On 1 On
f W S15RETENTION Keep retention on RAM section S15 when RAM section is switched off
On 1 On

5.3.7.47 RAM[8].POWERCLR
Address offset: 0x988
RAM8 power control clear register
When read, this register will return the value of the POWER register.

4413_417 v1.9 152

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A W S0POWER Keep RAM section S0 of RAM8 on or off in System ON mode
Off 1 Off
B W S1POWER Keep RAM section S1 of RAM8 on or off in System ON mode
Off 1 Off
C W S2POWER Keep RAM section S2 of RAM8 on or off in System ON mode
Off 1 Off
D W S3POWER Keep RAM section S3 of RAM8 on or off in System ON mode
Off 1 Off
E W S4POWER Keep RAM section S4 of RAM8 on or off in System ON mode
Off 1 Off
F W S5POWER Keep RAM section S5 of RAM8 on or off in System ON mode
Off 1 Off
G W S6POWER Keep RAM section S6 of RAM8 on or off in System ON mode
Off 1 Off
H W S7POWER Keep RAM section S7 of RAM8 on or off in System ON mode
Off 1 Off
I W S8POWER Keep RAM section S8 of RAM8 on or off in System ON mode
Off 1 Off
J W S9POWER Keep RAM section S9 of RAM8 on or off in System ON mode
Off 1 Off
K W S10POWER Keep RAM section S10 of RAM8 on or off in System ON mode
Off 1 Off
L W S11POWER Keep RAM section S11 of RAM8 on or off in System ON mode
Off 1 Off
M W S12POWER Keep RAM section S12 of RAM8 on or off in System ON mode
Off 1 Off
N W S13POWER Keep RAM section S13 of RAM8 on or off in System ON mode
Off 1 Off
O W S14POWER Keep RAM section S14 of RAM8 on or off in System ON mode
Off 1 Off
P W S15POWER Keep RAM section S15 of RAM8 on or off in System ON mode
Off 1 Off
Q W S0RETENTION Keep retention on RAM section S0 when RAM section is switched off
Off 1 Off
R W S1RETENTION Keep retention on RAM section S1 when RAM section is switched off
Off 1 Off
S W S2RETENTION Keep retention on RAM section S2 when RAM section is switched off
Off 1 Off
T W S3RETENTION Keep retention on RAM section S3 when RAM section is switched off
Off 1 Off
U W S4RETENTION Keep retention on RAM section S4 when RAM section is switched off
Off 1 Off
V W S5RETENTION Keep retention on RAM section S5 when RAM section is switched off
Off 1 Off
W W S6RETENTION Keep retention on RAM section S6 when RAM section is switched off
Off 1 Off
X W S7RETENTION Keep retention on RAM section S7 when RAM section is switched off
Off 1 Off
Y W S8RETENTION Keep retention on RAM section S8 when RAM section is switched off
Off 1 Off

4413_417 v1.9 153

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x0000FFFF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
Z W S9RETENTION Keep retention on RAM section S9 when RAM section is switched off
Off 1 Off
a W S10RETENTION Keep retention on RAM section S10 when RAM section is switched off
Off 1 Off
b W S11RETENTION Keep retention on RAM section S11 when RAM section is switched off
Off 1 Off
c W S12RETENTION Keep retention on RAM section S12 when RAM section is switched off
Off 1 Off
d W S13RETENTION Keep retention on RAM section S13 when RAM section is switched off
Off 1 Off
e W S14RETENTION Keep retention on RAM section S14 when RAM section is switched off
Off 1 Off
f W S15RETENTION Keep retention on RAM section S15 when RAM section is switched off
Off 1 Off

5.3.8 Electrical specification

5.3.8.1 Regulator operating conditions

Symbol Description Min. Typ. Max. Units

VDD,POR VDD supply voltage needed during power-on reset 1.75 V
VDD Normal voltage mode operating voltage 1.7 3.0 3.6 V
VDDH High voltage mode operating voltage 2.5 3.7 5.5 V
CVDD Effective decoupling capacitance on the VDD pin 2.7 4.7 5.5 µF
CDEC4 Effective decoupling capacitance on the DEC4 pin 0.7 1 1.3 µF

5.3.8.2 Regulator specifications, REG0 stage

Symbol Description Min. Typ. Max. Units

VREG0OUT REG0 output voltage 1.8 3.3 V
VREG0OUT,ERR REG0 output voltage error (deviation from setting in REGOUT0 on page 62) -10 5 %
VVDDH-VDD Required difference between input voltage (VDDH) and output voltage (VDD, 0.3 V
configured in REGOUT0 on page 62), VDDH > VDD
IEXT,OFF External current draw11 allowed in High voltage mode (supply on VDDH) 1 mA

during System OFF.

IEXT,LOW External current draw11 allowed in High voltage mode (supply on VDDH) 5 mA

when radio output power is higher than 4 dBm.

IEXT,HIGH External current draw11 allowed in High voltage mode (supply on VDDH) 25 mA

when radio output power is lower than or equal to 4 dBm.

11
External current draw is defined as the sum of all GPIO currents and the current being drawn from
VDD.

4413_417 v1.9 154

 Power and clock management

5.3.8.3 Device startup times

Symbol Description Min. Typ. Max. Units

tPOR Time in power-on reset after supply reaches minimum operating voltage,
depending on supply rise time
tPOR,10µs VDD rise time 10 µs12 1 10 ms

tPOR,10ms VDD rise time 10 ms12 9 ms

tPOR,60ms VDD rise time 60 ms12 23 110 ms

tRISE,REG0OUT REG0 output (VDD) rise time after VDDH reaches minimum VDDH supply

voltage12
tRISE,REG0OUT,10µs VDDH rise time 10 µs12 0.22 1.55 ms

tRISE,REG0OUT,10ms VDDH rise time 10 ms 12 5 ms

tRISE,REG0OUT,100ms VDDH rise time 100 ms12 30 50 80 ms

tPINR Reset time when using pin reset, depending on pin capacitance
tPINR,500nF 500 nF capacitance at reset pin 32.5 ms
tPINR,10µF 10 µF capacitance at reset pin 650 ms
tR2ON Time from power-on reset to System ON
tR2ON,NOTCONF If reset pin not configured tPOR ms
tR2ON,CONF If reset pin configured tPOR + ms
tPINR
tOFF2ON Time from OFF to CPU execute 16.5 µs
tIDLE2CPU Time from IDLE to CPU execute 3.0 µs
tEVTSET,CL1 Time from HW event to PPI event in Constant Latency System ON mode 0.0625 µs
tEVTSET,CL0 Time from HW event to PPI event in Low Power System ON mode 0.0625 µs

5.3.8.4 Power fail comparator

Symbol Description Min. Typ. Max. Units

VPOF,NV Nominal power level warning thresholds (falling supply voltage) in Normal 1.7 2.8 V
voltage mode (supply on VDD). Levels are configurable between Min. and
Max. in 100 mV increments
VPOF,HV Nominal power level warning thresholds (falling supply voltage) in High 2.7 4.2 V
voltage mode (supply on VDDH). Levels are configurable in 100 mV
increments
VPOFTOL Threshold voltage tolerance (applies in both Normal voltage mode and High -5 5 %
voltage mode)
VPOFHYST Threshold voltage hysteresis (applies in both Normal voltage mode and High 40 50 60 mV
voltage mode)
VBOR,OFF Brownout reset voltage range System OFF mode. Brownout only applies to 1.2 1.62 V
the voltage on VDD
VBOR,ON Brownout reset voltage range System ON mode. Brownout only applies to the 1.57 1.6 1.63 V
voltage on VDD

5.3.8.5 USB operating conditions

Symbol Description Min. Typ. Max. Units

VBUS Supply voltage on VBUS pin 4.35 5 5.5 V
VDPDM Voltage on D+ and D- lines VSS - 0.3 VUSB33 + V
0.3

12
See Recommended operating conditions on page 890 for more information.

4413_417 v1.9 155

 Power and clock management

5.3.8.6 USB regulator specifications

Symbol Description Min. Typ. Max. Units

IUSB,QUIES USB regulator quiescent current drawn from VBUS (USBD enabled) 170 µA
tUSBPWRRDY Time from USB enabled to USBPWRRDY event triggered, VBUS supply provided 1 ms
VUSB33 On voltage at the USB regulator output (DECUSB pin) 3.0 3.3 3.6 V
RSOURCE,VBUS Maximum source resistance on VBUS, including cable, when VDDH is not 6 Ω
connected to VBUS
RSOURCE,VBUSVDDH Maximum source resistance on VBUS, including cable, when VDDH is 3.8 Ω
connected to VBUS
CDECUSB Decoupling capacitor on the DECUSB pin 2.35 4.7 5.5 µF

5.3.8.7 VBUS detection specifications

Symbol Description Min. Typ. Max. Units

VBUS,DETECT Voltage at which rising VBUS gets reported by USBDETECTED 3.4 4.0 4.3 V
VBUS,REMOVE Voltage at which decreasing VBUS gets reported by USBREMOVED 3.0 3.6 3.9 V

5.4 CLOCK — Clock control

The clock control system can source the system clocks from a range of internal or external high and low
frequency oscillators and distribute them to modules based upon a module’s individual requirements.
Clock distribution is automated and grouped independently by module to limit current consumption in
unused branches of the clock tree.
Listed here are the main features for CLOCK:
• 64 MHz on-chip oscillator
• 64 MHz crystal oscillator, using external 32 MHz crystal
• 32.768 kHz +/-500 ppm RC oscillator
• 32.768 kHz crystal oscillator, using external 32.768 kHz crystal
• 32.768 kHz oscillator synthesized from 64 MHz oscillator
• Firmware (FW) override control of crystal oscillator activity for low latency start up
• Automatic internal oscillator and clock control, and distribution for ultra-low power

4413_417 v1.9 156

 Power and clock management

HFCLKSTART HFCLKSTOP LFCLKSTART LFCLKSTOP

CLOCK

HFINT
Internal oscillator

PCLK1M
PCLK16M
XC1 HFCLK PCLK32M
Clock control
HFXO
32 MHz
Crystal oscillator
HCLK64M
XC2

LFRC
CAL SYNT
RC oscillator

XL1

LFXO LFCLK
32.768 kHz PCLK32KI
Crystal oscillator Clock control

XL2

HFCLKSTARTED LFCLKSTARTED

Figure 22: Clock control

5.4.1 HFCLK controller

The HFCLK controller provides several clock signals in the system.
These are as follows:
• HCLK64M: 64 MHz CPU clock
• PCLK1M: 1 MHz peripheral clock
• PCLK16M: 16 MHz peripheral clock
• PCLK32M: 32 MHz peripheral clock
The HFCLK controller uses the following high frequency clock (HFCLK) sources:
• 64 MHz internal oscillator (HFINT)
• 64 MHz crystal oscillator (HFXO)
For illustration, see Clock control on page 157.
The HFCLK controller will automatically provide the clock(s) requested by the system. If the system does
not request any clocks from the HFCLK controller, the controller will enter a power saving mode.
The HFINT source will be used when HFCLK is requested and HFXO has not been started.
The HFXO is started by triggering the HFCLKSTART task and stopped by triggering the HFCLKSTOP task.
When the HFCLKSTART task is triggered, the HFCLKSTARTED event is generated once the HFXO startup
time has elapsed. The HFXO startup time is given as the sum of the following:
• HFXO power-up time, as specified in 64 MHz crystal oscillator (HFXO) on page 170.
• HFXO debounce time, as specified in register HFXODEBOUNCE on page 168.
The HFXO must be running to use the RADIO or the calibration mechanism associated with the 32.768 kHz
RC oscillator.

4413_417 v1.9 157

 Power and clock management

5.4.1.1 64 MHz crystal oscillator (HFXO)

The 64 MHz crystal oscillator (HFXO) is controlled by a 32 MHz external crystal.
The crystal oscillator is designed for use with an AT-cut quartz crystal in parallel resonant mode. To achieve
correct oscillation frequency, the load capacitance must match the specification in the crystal data sheet.
Circuit diagram of the 64 MHz crystal oscillator on page 158 shows how the 32 MHz crystal is connected
to the 64 MHz crystal oscillator.

XC1 XC2

C1 C2
32 MHz
crystal

Figure 23: Circuit diagram of the 64 MHz crystal oscillator

The load capacitance (CL) is the total capacitance seen by the crystal across its terminals and is given by:

C1 and C2 are ceramic SMD capacitors connected between each crystal terminal and ground. For more
information, see Reference circuitry on page 856. Cpcb1 and Cpcb2 are stray capacitances on the PCB. Cpin
is the pin input capacitance on the XC1 and XC2 pins. See table 64 MHz crystal oscillator (HFXO) on page
170. The load capacitors C1 and C2 should have the same value.
For reliable operation, the crystal load capacitance, shunt capacitance, equivalent series resistance, and
drive level must comply with the specifications in table 64 MHz crystal oscillator (HFXO) on page 170. It
is recommended to use a crystal with lower than maximum load capacitance and/or shunt capacitance. A
low load capacitance will reduce both start up time and current consumption.

5.4.2 LFCLK controller

The system supports several low frequency clock sources.
As illustrated in Clock control on page 157, the system supports the following low frequency clock
sources:
• 32.768 kHz RC oscillator (LFRC)
• 32.768 kHz crystal oscillator (LFXO)
• 32.768 kHz synthesized from HFCLK (LFSYNT)
The LFCLK controller and all of the LFCLK clock sources are always switched off when in System OFF mode.

4413_417 v1.9 158

 Power and clock management

The LFCLK clock is started by first selecting the preferred clock source in register LFCLKSRC on page 168
and then triggering the LFCLKSTART task. If the LFXO is selected as the clock source, the LFCLK will initially
start running from the 32.768 kHz LFRC while the LFXO is starting up and automatically switch to using the
LFXO once this oscillator is running. The LFCLKSTARTED event will be generated when the LFXO has been
started.
The LFCLK clock is stopped by triggering the LFCLKSTOP task.
Register LFCLKSRC on page 168 controls the clock source, and its allowed swing. The truth table for
various situations is as follows:

SRC EXTERNAL BYPASS Comment

0 0 0 Normal operation, LFRC is source

0 0 1 DO NOT USE
0 1 X DO NOT USE
1 0 0 Normal XTAL operation
1 1 0 Apply external low swing signal to XL1, ground XL2
1 1 1 Apply external full swing signal to XL1, leave XL2 grounded or unconnected
1 0 1 DO NOT USE
2 0 0 Normal operation, LFSYNT is source
2 0 1 DO NOT USE
2 1 X DO NOT USE

Table 8: LFCLKSRC configuration depending on clock source

It is not allowed to write to register LFCLKSRC on page 168 when the LFCLK is running.
A LFCLKSTOP task will stop the LFCLK oscillator. However, the LFCLKSTOP task can only be triggered after
the STATE field in register LFCLKSTAT on page 167 indicates LFCLK running state.
The synthesized 32.768 kHz clock depends on the HFCLK to run. If high accuracy is required for the LFCLK
running off the synthesized 32.768 kHz clock, the HFCLK must running from the HFXO source.

5.4.2.1 32.768 kHz RC oscillator (LFRC)

The default source of the low frequency clock (LFCLK) is the 32.768 kHz RC oscillator (LFRC).
The LFRC oscillator does not require additional external components.
The LFRC oscillator has two modes of operation, normal and ultra-low power (ULP) mode, enabling the
user to trade power consumption against accuracy of the clock. The LFRC mode is configured in register
LFRCMODE. The LFRC oscillator has to be stopped before changing the mode of the oscillator.
The LFRC frequency will be affected by variation in temperature. The LFRC oscillator can be calibrated to
improve accuracy by using the HFXO as a reference oscillator during calibration.

5.4.2.2 Calibrating the 32.768 kHz RC oscillator

After the LFRC oscillator is started and running, it can be calibrated by triggering the CAL task.
The LFRC oscillator will then temporarily request the HFCLK to be used as a reference for the calibration. A
DONE event will be generated when calibration has finished. The HFCLK crystal oscillator has to be started
(by triggering the HFCLKSTART task) in order for the calibration mechanism to work.
It is not allowed to stop the LFRC or write to LFRCMODE during an ongoing calibration.

5.4.2.3 Calibration timer

The calibration timer can be used to time the calibration interval of the 32.768 kHz RC oscillator.
The calibration timer is started by triggering the CTSTART task and stopped by triggering the CTSTOP task.
The calibration timer will always start counting down from the value specified in CTIV (Retained) on page

4413_417 v1.9 159

 Power and clock management

168 and generate a CTTO event when it reaches 0. The calibration timer will automatically stop when it
reaches 0.

CTSTART
CTSTARTED
Calibration
CTSTOP CTIV
CTSTOPPED timer
CTTO

Figure 24: Calibration timer

After a CTSTART task has been triggered, the calibration timer will ignore further tasks until it has returned
the CTSTARTED event. Likewise, after a CTSTOP task has been triggered, the calibration timer will ignore
further tasks until it has returned a CTSTOPPED event. Triggering CTSTART while the calibration timer
is running will immediately return a CTSTARTED event. Triggering CTSTOP when the calibration timer is
stopped will immediately return a CTSTOPPED event.

5.4.2.4 32.768 kHz crystal oscillator (LFXO)

For higher LFCLK accuracy (when better than +/- 500 ppm accuracy is required), the low frequency crystal
oscillator (LFXO) must be used.
The following external clock sources are supported:
• Low swing clock signal applied to the XL1 pin. The XL2 pin shall then be grounded.
• Rail-to-rail clock signal applied to the XL1 pin. The XL2 pin shall then be grounded or left unconnected.
To achieve correct oscillation frequency, the load capacitance must match the specification in the crystal
data sheet. Circuit diagram of the 32.768 kHz crystal oscillator on page 160 shows the LFXO circuitry.

XL1 XL2

C1 C2
32.768 kHz
crystal

Figure 25: Circuit diagram of the 32.768 kHz crystal oscillator

The load capacitance (CL) is the total capacitance seen by the crystal across its terminals and is given by:

C1 and C2 are ceramic SMD capacitors connected between each crystal terminal and ground. Cpcb1 and
Cpcb2 are stray capacitances on the PCB. Cpin is the pin input capacitance on the XC1 and XC2 pins (see Low
frequency crystal oscillator (LFXO) on page 170). The load capacitors C1 and C2 should have the same
value.

4413_417 v1.9 160

 Power and clock management

For more information, see Reference circuitry on page 856.

5.4.2.5 32.768 kHz synthesized from HFCLK (LFSYNT)

LFCLK can also be synthesized from the HFCLK clock source. The accuracy of LFCLK will then be the
accuracy of the HFCLK.
Using the LFSYNT clock avoids the requirement for a 32.768 kHz crystal, but increases average power
consumption as the HFCLK will need to be requested in the system.

5.4.3 Registers
Instances

Instance Base address Description

CLOCK 0x40000000 Clock control

Register overview

Register Offset Description

TASKS_HFCLKSTART 0x000 Start HFXO crystal oscillator
TASKS_HFCLKSTOP 0x004 Stop HFXO crystal oscillator
TASKS_LFCLKSTART 0x008 Start LFCLK
TASKS_LFCLKSTOP 0x00C Stop LFCLK
TASKS_CAL 0x010 Start calibration of LFRC
TASKS_CTSTART 0x014 Start calibration timer
TASKS_CTSTOP 0x018 Stop calibration timer
EVENTS_HFCLKSTARTED 0x100 HFXO crystal oscillator started
EVENTS_LFCLKSTARTED 0x104 LFCLK started
EVENTS_DONE 0x10C Calibration of LFRC completed
EVENTS_CTTO 0x110 Calibration timer timeout
EVENTS_CTSTARTED 0x128 Calibration timer has been started and is ready to process new tasks
EVENTS_CTSTOPPED 0x12C Calibration timer has been stopped and is ready to process new tasks
INTENSET 0x304 Enable interrupt
INTENCLR 0x308 Disable interrupt
HFCLKRUN 0x408 Status indicating that HFCLKSTART task has been triggered
HFCLKSTAT 0x40C HFCLK status
LFCLKRUN 0x414 Status indicating that LFCLKSTART task has been triggered
LFCLKSTAT 0x418 LFCLK status
LFCLKSRCCOPY 0x41C Copy of LFCLKSRC register, set when LFCLKSTART task was triggered
LFCLKSRC 0x518 Clock source for the LFCLK
HFXODEBOUNCE 0x528 HFXO debounce time. The HFXO is started by triggering the TASKS_HFCLKSTART task.
CTIV 0x538 Calibration timer interval

This register is retained.

TRACECONFIG 0x55C Clocking options for the trace port debug interface
LFRCMODE 0x5B4 LFRC mode configuration

5.4.3.1 TASKS_HFCLKSTART
Address offset: 0x000
Start HFXO crystal oscillator

4413_417 v1.9 161

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_HFCLKSTART Start HFXO crystal oscillator
Trigger 1 Trigger task

5.4.3.2 TASKS_HFCLKSTOP
Address offset: 0x004
Stop HFXO crystal oscillator

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_HFCLKSTOP Stop HFXO crystal oscillator
Trigger 1 Trigger task

5.4.3.3 TASKS_LFCLKSTART
Address offset: 0x008
Start LFCLK

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_LFCLKSTART Start LFCLK
Trigger 1 Trigger task

5.4.3.4 TASKS_LFCLKSTOP
Address offset: 0x00C
Stop LFCLK

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_LFCLKSTOP Stop LFCLK
Trigger 1 Trigger task

5.4.3.5 TASKS_CAL
Address offset: 0x010
Start calibration of LFRC

4413_417 v1.9 162

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_CAL Start calibration of LFRC
Trigger 1 Trigger task

5.4.3.6 TASKS_CTSTART
Address offset: 0x014
Start calibration timer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_CTSTART Start calibration timer
Trigger 1 Trigger task

5.4.3.7 TASKS_CTSTOP
Address offset: 0x018
Stop calibration timer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_CTSTOP Stop calibration timer
Trigger 1 Trigger task

5.4.3.8 EVENTS_HFCLKSTARTED
Address offset: 0x100
HFXO crystal oscillator started

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_HFCLKSTARTED HFXO crystal oscillator started
NotGenerated 0 Event not generated
Generated 1 Event generated

5.4.3.9 EVENTS_LFCLKSTARTED
Address offset: 0x104
LFCLK started

4413_417 v1.9 163

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_LFCLKSTARTED LFCLK started
NotGenerated 0 Event not generated
Generated 1 Event generated

5.4.3.10 EVENTS_DONE
Address offset: 0x10C
Calibration of LFRC completed

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_DONE Calibration of LFRC completed
NotGenerated 0 Event not generated
Generated 1 Event generated

5.4.3.11 EVENTS_CTTO
Address offset: 0x110
Calibration timer timeout

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_CTTO Calibration timer timeout
NotGenerated 0 Event not generated
Generated 1 Event generated

5.4.3.12 EVENTS_CTSTARTED
Address offset: 0x128
Calibration timer has been started and is ready to process new tasks

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_CTSTARTED Calibration timer has been started and is ready to process new tasks
NotGenerated 0 Event not generated
Generated 1 Event generated

5.4.3.13 EVENTS_CTSTOPPED
Address offset: 0x12C
Calibration timer has been stopped and is ready to process new tasks

4413_417 v1.9 164

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_CTSTOPPED Calibration timer has been stopped and is ready to process new tasks
NotGenerated 0 Event not generated
Generated 1 Event generated

5.4.3.14 INTENSET
Address offset: 0x304
Enable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW HFCLKSTARTED Write '1' to enable interrupt for event HFCLKSTARTED
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW LFCLKSTARTED Write '1' to enable interrupt for event LFCLKSTARTED
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW DONE Write '1' to enable interrupt for event DONE
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
D RW CTTO Write '1' to enable interrupt for event CTTO
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
E RW CTSTARTED Write '1' to enable interrupt for event CTSTARTED
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
F RW CTSTOPPED Write '1' to enable interrupt for event CTSTOPPED
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

5.4.3.15 INTENCLR
Address offset: 0x308
Disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW HFCLKSTARTED Write '1' to disable interrupt for event HFCLKSTARTED
Clear 1 Disable

4413_417 v1.9 165

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW LFCLKSTARTED Write '1' to disable interrupt for event LFCLKSTARTED
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW DONE Write '1' to disable interrupt for event DONE
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
D RW CTTO Write '1' to disable interrupt for event CTTO
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
E RW CTSTARTED Write '1' to disable interrupt for event CTSTARTED
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
F RW CTSTOPPED Write '1' to disable interrupt for event CTSTOPPED
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

5.4.3.16 HFCLKRUN
Address offset: 0x408
Status indicating that HFCLKSTART task has been triggered

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R STATUS HFCLKSTART task triggered or not
NotTriggered 0 Task not triggered
Triggered 1 Task triggered

5.4.3.17 HFCLKSTAT
Address offset: 0x40C
HFCLK status

4413_417 v1.9 166

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R SRC Source of HFCLK
RC 0 64 MHz internal oscillator (HFINT)
Xtal 1 64 MHz crystal oscillator (HFXO)
B R STATE HFCLK state
NotRunning 0 HFCLK not running
Running 1 HFCLK running

5.4.3.18 LFCLKRUN
Address offset: 0x414
Status indicating that LFCLKSTART task has been triggered

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R STATUS LFCLKSTART task triggered or not
NotTriggered 0 Task not triggered
Triggered 1 Task triggered

5.4.3.19 LFCLKSTAT
Address offset: 0x418
LFCLK status

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R SRC Source of LFCLK
RC 0 32.768 kHz RC oscillator (LFRC)
Xtal 1 32.768 kHz crystal oscillator (LFXO)
Synth 2 32.768 kHz synthesized from HFCLK (LFSYNT)
B R STATE LFCLK state
NotRunning 0 LFCLK not running
Running 1 LFCLK running

5.4.3.20 LFCLKSRCCOPY
Address offset: 0x41C
Copy of LFCLKSRC register, set when LFCLKSTART task was triggered

4413_417 v1.9 167

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R SRC Clock source
RC 0 32.768 kHz RC oscillator (LFRC)
Xtal 1 32.768 kHz crystal oscillator (LFXO)
Synth 2 32.768 kHz synthesized from HFCLK (LFSYNT)

5.4.3.21 LFCLKSRC
Address offset: 0x518
Clock source for the LFCLK

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW SRC Clock source
RC 0 32.768 kHz RC oscillator (LFRC)
Xtal 1 32.768 kHz crystal oscillator (LFXO)
Synth 2 32.768 kHz synthesized from HFCLK (LFSYNT)
B RW BYPASS Enable or disable bypass of LFCLK crystal oscillator with external clock
source
Disabled 0 Disable (use with Xtal or low-swing external source)
Enabled 1 Enable (use with rail-to-rail external source)
C RW EXTERNAL Enable or disable external source for LFCLK
Disabled 0 Disable external source (use with Xtal)
Enabled 1 Enable use of external source instead of Xtal (SRC needs to be set to Xtal)

5.4.3.22 HFXODEBOUNCE
Address offset: 0x528
HFXO debounce time. The HFXO is started by triggering the TASKS_HFCLKSTART task.
The EVENTS_HFCLKSTARTED event is generated after the HFXO power up time + the HFXO debounce time
has elapsed. It is not allowed to change the value of this register while the HFXO is starting.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A

Reset 0x00000010 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0
ID R/W Field Value ID Value Description
A RW HFXODEBOUNCE 0x01..0xFF HFXO debounce time. Debounce time = HFXODEBOUNCE * 16 µs.
Db256us 0x10 256 µs debounce time. Recommended for TSX-3225, FA-20H and FA-128
crystals.
Db1024us 0x40 1024 µs debounce time. Recommended for NX1612AA and NX1210AB
crystals.

5.4.3.23 CTIV (Retained)

Address offset: 0x538
Calibration timer interval
This register is retained.

4413_417 v1.9 168

 Power and clock management

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW CTIV Calibration timer interval in multiple of 0.25 seconds. Range: 0.25 seconds
to 31.75 seconds.

5.4.3.24 TRACECONFIG
Address offset: 0x55C
Clocking options for the trace port debug interface
This register is a retained register. Reset behavior is the same as debug components.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B B A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TRACEPORTSPEED Speed of trace port clock. Note that the TRACECLK pin will output this clock
divided by two.
32MHz 0 32 MHz trace port clock (TRACECLK = 16 MHz)
16MHz 1 16 MHz trace port clock (TRACECLK = 8 MHz)
8MHz 2 8 MHz trace port clock (TRACECLK = 4 MHz)
4MHz 3 4 MHz trace port clock (TRACECLK = 2 MHz)
B RW TRACEMUX Pin multiplexing of trace signals. See pin assignment chapter for more
details.
GPIO 0 No trace signals routed to pins. All pins can be used as regular GPIOs.
Serial 1 SWO trace signal routed to pin. Remaining pins can be used as regular
GPIOs.
Parallel 2 All trace signals (TRACECLK and TRACEDATA[n]) routed to pins.

5.4.3.25 LFRCMODE
Address offset: 0x5B4
LFRC mode configuration

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW MODE Set LFRC mode
Normal 0 Normal mode
ULP 1 Ultra-low power mode (ULP)
B RW STATUS Active LFRC mode. This field is read only.
Normal 0 Normal mode
ULP 1 Ultra-low power mode (ULP)

5.4.4 Electrical specification

5.4.4.1 64 MHz internal oscillator (HFINT)

4413_417 v1.9 169

 Power and clock management

Symbol Description Min. Typ. Max. Units

fNOM_HFINT Nominal output frequency 64 MHz
fTOL_HFINT Frequency tolerance ±1.5 ±8 %

5.4.4.2 64 MHz crystal oscillator (HFXO)

Symbol Description Min. Typ. Max. Units

fNOM_HFXO Nominal output frequency 64 MHz
fXTAL_HFXO External crystal frequency 32 MHz
fTOL_HFXO Frequency tolerance requirement for 2.4 GHz proprietary radio applications ±60 ppm
fTOL_HFXO_BLE Frequency tolerance requirement, Bluetooth low energy applications, packet ±40 ppm
length ≤ 200 bytes
fTOL_HFXO_BLE_LP Frequency tolerance requirement, Bluetooth low energy applications, packet ±30 ppm
length > 200 bytes
CL_HFXO Load capacitance 12 pF
C0_HFXO Shunt capacitance 7 pF
RS_HFXO_7PF Equivalent series resistance 3 pF < C0 ≤ 7 pF 60 Ω
RS_HFXO_3PF Equivalent series resistance C0 ≤ 3 pF 100 Ω
PD_HFXO Drive level 100 µW
CPIN_HFXO Input capacitance XC1 and XC2 3 pF
ISTBY_X32M Core standby current for various crystals
ISTBY_X32M_X0 Epson TSX-3225 80 µA
ISTBY_X32M_X1 Epson FA-20H 72 µA
ISTBY_X32M_X2 Epson FA-128 70 µA
ISTBY_X32M_X3 NDK NX1612AA 136 µA
ISTBY_X32M_X4 NDK NX1210AB 143 µA
ISTART_X32M Average startup current for various crystals, first 1 ms
ISTART_X32M_X0 Epson TSX-3225 328 µA
ISTART_X32M_X1 Epson FA-20H 363 µA
ISTART_X32M_X2 Epson FA-128 396 µA
ISTART_X32M_X3 NDK NX1612AA 783 µA
ISTART_X32M_X4 NDK NX1210AB 833 µA
tPOWER_X32M Power-up time for various crystals
tPOWER_X32M_X0 Epson TSX-3225 50 µs
tPOWER_X32M_X1 Epson FA-20H 60 µs
tPOWER_X32M_X2 Epson FA-128 75 µs
tPOWER_X32M_X3 NDK NX1612AA 195 µs
tPOWER_X32M_X4 NDK NX1210AB 210 µs

5.4.4.3 Low frequency crystal oscillator (LFXO)

Symbol Description Min. Typ. Max. Units

fNOM_LFXO Crystal frequency 32.768 kHz
fTOL_LFXO_BLE Frequency tolerance requirement for BLE stack ±500 ppm
fTOL_LFXO_ANT Frequency tolerance requirement for ANT stack ±50 ppm
CL_LFXO Load capacitance 12.5 pF
C0_LFXO Shunt capacitance 2 pF
RS_LFXO Equivalent series resistance 100 kΩ
PD_LFXO Drive level 0.5 μW
Cpin Input capacitance on XL1 and XL2 pads 4 pF
ILFXO Run current for 32.768 kHz crystal oscillator 0.23 µA
tSTART_LFXO Startup time for 32.768 kHz crystal oscillator 0.25 s

4413_417 v1.9 170

 Power and clock management

Symbol Description Min. Typ. Max. Units

VAMP,IN,XO,LOW Peak to peak amplitude for external low swing clock. Input signal must not 200 1000 mV
swing outside supply rails.

5.4.4.4 Low frequency RC oscillator (LFRC)

Symbol Description Min. Typ. Max. Units

fNOM_LFRC Nominal frequency 32.768 kHz
fTOL_LFRC Frequency tolerance, uncalibrated ±5 %
fTOL_CAL_LFRC Frequency tolerance after calibration13 ±500 ppm

ILFRC Run current 0.7 µA

tSTART_LFRC Startup time 1000 μs

5.4.4.5 Low frequency RC oscillator (LFRC), Ultra-low power mode (ULP)

Symbol Description Min. Typ. Max. Units

fNOM_LFULP Nominal frequency 32.768 kHz
fTOL_UNCAL_LFULP Frequency tolerance, uncalibrated ±7 %
fTOL_CAL_LFULP Frequency tolerance after calibration14 ±2000 ppm

ILFULP Run current 0.3 µA

tSTART_LFULP Startup time 1500 μs

5.4.4.6 Synthesized low frequency clock (LFSYNT)

Symbol Description Min. Typ. Max. Units

fNOM_LFSYNT Nominal frequency 32.768 kHz

13
Constant temperature within ±0.5 °C, calibration performed at least every 8 seconds, averaging
interval > 7.5 ms, defined as 3 sigma
14
Constant temperature within ±0.5 °C, calibration performed at least every 8 seconds, averaging
interval > 125 ms, defined as 3 sigma

4413_417 v1.9 171

6 Peripherals

6.1 Peripheral interface

Peripherals are controlled by the CPU by writing to configuration registers and task registers. Peripheral
events are indicated to the CPU by event registers and interrupts if they are configured for a given event.

Task signal from PPI

Peripheral

write
TASK

k SHORTS
OR

task

Peripheral
core

event

INTEN m

EVENT m
IRQ signal to NVIC

Event signal to PPI

Figure 26: Tasks, events, shortcuts, and interrupts

6.1.1 Peripheral ID
Every peripheral is assigned a fixed block of 0x1000 bytes of address space, which is equal to 1024 x 32 bit
registers.
See Instantiation on page 24 for more information about which peripherals are available and where they
are located in the address map.
There is a direct relationship between peripheral ID and base address. For example, a peripheral with base
address 0x40000000 is assigned ID=0, a peripheral with base address 0x40001000 is assigned ID=1, and a
peripheral with base address 0x4001F000 is assigned ID=31.
Peripherals may share the same ID, which may impose one or more of the following limitations:
• Some peripherals share some registers or other common resources.
• Operation is mutually exclusive. Only one of the peripherals can be used at a time.
• Switching from one peripheral to another must follow a specific pattern (disable the first, then enable
the second peripheral).

4413_417 v1.9 172

 Peripherals

6.1.2 Peripherals with shared ID

In general (with the exception of ID 0), peripherals sharing an ID and base address may not be used
simultaneously. The user can only enable one peripheral at the time on this specific ID.
When switching between two peripherals sharing an ID, the user should do the following to prevent
unwanted behavior:
1. Disable the previously used peripheral.
2. Remove any programmable peripheral interconnect (PPI) connections set up for the peripheral that is
being disabled.
3. Clear all bits in the INTEN register, i.e. INTENCLR = 0xFFFFFFFF.
4. Explicitly configure the peripheral that you are about to enable and do not rely on configuration values
that may be inherited from the peripheral that was disabled.
5. Enable the now configured peripheral.
See which peripherals are sharing ID in Instantiation on page 24.

6.1.3 Peripheral registers

Most peripherals feature an ENABLE register. Unless otherwise specified in the relevant chapter, the
peripheral registers (in particular the PSEL registers) must be configured before enabling the peripheral.
The peripheral must be enabled before tasks and events can be used.

6.1.4 Bit set and clear

Registers with multiple single-bit bit fields may implement the set-and-clear pattern. This pattern enables
firmware to set and clear individual bits in a register without having to perform a read-modify-write
operation on the main register.
This pattern is implemented using three consecutive addresses in the register map, where the main
register is followed by dedicated SET and CLR registers (in that exact order).
The SET register is used to set individual bits in the main register while the CLR register is used to clear
individual bits in the main register. Writing 1 to a bit in SET or CLR register will set or clear the same bit in
the main register respectively. Writing 0 to a bit in SET or CLR register has no effect. Reading the SET or
CLR register returns the value of the main register.

Note: The main register may not be visible and hence not directly accessible in all cases.

6.1.5 Tasks
Tasks are used to trigger actions in a peripheral, for example to start a particular behavior. A peripheral can
implement multiple tasks with each task having a separate register in that peripheral's task register group.
A task is triggered when firmware writes 1 to the task register, or when the peripheral itself or another
peripheral toggles the corresponding task signal. See Tasks, events, shortcuts, and interrupts on page
172.

6.1.6 Events
Events are used to notify peripherals and the CPU about events that have happened, for example a state
change in a peripheral. A peripheral may generate multiple events with each event having a separate
register in that peripheral’s event register group.
An event is generated when the peripheral itself toggles the corresponding event signal, and the event
register is updated to reflect that the event has been generated. See Tasks, events, shortcuts, and
interrupts on page 172. An event register is only cleared when firmware writes 0 to it.

4413_417 v1.9 173

 Peripherals

Events can be generated by the peripheral even when the event register is set to 1.

6.1.7 Shortcuts
A shortcut is a direct connection between an event and a task within the same peripheral. If a shortcut is
enabled, the associated task is automatically triggered when its associated event is generated.
Using a shortcut is the equivalent to making the same connection outside the peripheral and through the
PPI. However, the propagation delay through the shortcut is usually shorter than the propagation delay
through the PPI.
Shortcuts are predefined, which means their connections cannot be configured by firmware. Each shortcut
can be individually enabled or disabled through the shortcut register, one bit per shortcut, giving a
maximum of 32 shortcuts for each peripheral.

6.1.8 Interrupts
All peripherals support interrupts. Interrupts are generated by events.
A peripheral only occupies one interrupt, and the interrupt number follows the peripheral ID. For example,
the peripheral with ID=4 is connected to interrupt number 4 in the nested vectored interrupt controller
(NVIC).
Using the INTEN, INTENSET, and INTENCLR registers, every event generated by a peripheral can be
configured to generate that peripheral's interrupt. Multiple events can be enabled to generate interrupts
simultaneously. To resolve the correct interrupt source, the event registers in the event group of
peripheral registers will indicate the source.
Some peripherals implement only INTENSET and INTENCLR registers, and the INTEN register is not
available on those peripherals. See the individual peripheral chapters for details. In all cases, reading back
the INTENSET or INTENCLR register returns the same information as in INTEN.
Each event implemented in the peripheral is associated with a specific bit position in the INTEN, INTENSET,
and INTENCLR registers.
The relationship between tasks, events, shortcuts, and interrupts is shown in Tasks, events, shortcuts, and
interrupts on page 172.

Interrupt clearing
Clearing an interrupt by writing 0 to an event register, or disabling an interrupt using the INTENCLR
register, can take up to four CPU clock cycles to take effect. This means that an interrupt may reoccur
immediately, even if a new event has not come, if the program exits an interrupt handler after the
interrupt is cleared or disabled but before four clock cycles have passed.

Note: To avoid an interrupt reoccurring before a new event has come, the program should perform
a read from one of the peripheral registers. For example, the event register that has been cleared,
or the INTENCLR register that has been used to disable the interrupt. This will cause a one to three-
cycle delay and ensure the interrupt is cleared before exiting the interrupt handler.

Care should be taken to ensure the compiler does not remove the read operation as an optimization. If the
program can guarantee a four-cycle delay after an event is cleared or an interrupt is disabled, then a read
of a register is not required.

4413_417 v1.9 174

 Peripherals

6.2 AAR — Accelerated address resolver

Accelerated address resolver is a cryptographic support function for implementing the Resolvable Private
Address Resolution procedure described in Bluetooth Core Specification v4.0. Resolvable Private Address
generation should be achieved using ECB and is not supported by AAR.
The procedure allows two devices that share a secret key to generate and resolve a hash based on their
device address. The AAR block enables real-time address resolution on incoming packets when configured
as described in this chapter. This allows real-time packet filtering (whitelisting) using a list of known shared
keys (Identity Resolving Keys (IRK) in Bluetooth).

6.2.1 EasyDMA
AAR implements EasyDMA for reading and writing to RAM. EasyDMA will have finished accessing RAM
when the END, RESOLVED, and NOTRESOLVED events are generated.
If the IRKPTR on page 180, ADDRPTR on page 180, and the SCRATCHPTR on page 180 is not
pointing to the Data RAM region, an EasyDMA transfer may result in a HardFault or RAM corruption. See
Memory on page 21 for more information about the different memory regions.

6.2.2 Resolving a resolvable address

A private resolvable address is composed of six bytes according to the Bluetooth Core Specification.
LSB MSB

random 10

hash prand
(24-bit) (24-bit)

Figure 27: Resolvable address

To resolve an address, the register ADDRPTR on page 180 must point to the start of the packet. The
resolver is started by triggering the START task. A RESOLVED event is generated when AAR manages to
resolve the address using one of the Identity Resolving Keys (IRK) found in the IRK data structure. AAR will
use the IRK specified in the register IRK0 to IRK15 starting from IRK0. The register NIRK on page 180
specifies how many IRKs should be used. The AAR module will generate a NOTRESOLVED event if it is not
able to resolve the address using the specified list of IRKs.
AAR will go through the list of available IRKs in the IRK data structure and for each IRK try to resolve the
address according to the Resolvable Private Address Resolution Procedure described in the Bluetooth
Core specification v4.0 [Vol 3] chapter 10.8.2.3. The time it takes to resolve an address varies due to the
location in the list of the resolvable address. The resolution time will also be affected by RAM accesses
performed by other peripherals and the CPU. See the Electrical specifications for more information about
resolution time.
AAR only compares the received address to those programmed in the module without checking the
address type.
AAR will stop as soon as it has managed to resolve the address, or after trying to resolve the address using
NIRK number of IRKs from the IRK data structure. AAR will generate an END event after it has stopped.

4413_417 v1.9 175

 Peripherals

SCRATCHPTR

START ADDR: resolvable address

Scratch area
ADDRPTR
RESOLVED
AAR

IRK data
S0 L S1 ADDR
structure

IRKPTR

Figure 28: Address resolution with packet preloaded into RAM

6.2.3 Example
The following example shows how to chain RADIO packet reception with address resolution using AAR.
AAR may be started as soon as the 6 bytes required by AAR have been received by RADIO and stored in
RAM. The ADDRPTR pointer must point to the start of packet.
SCRATCHPTR

START S0: S0 field of RADIO (optional)

PACKETPTR L: Length field of RADIO (optional)
Scratch area
ADDRPTR S1: S1 field of RADIO (optional)
RESOLVED ADDR: resolvable address
AAR

IRK data
S0 L S1 ADDR
structure

IRKPTR
From remote
transmitter
RADIO
RXEN

Figure 29: Address resolution with packet loaded into RAM by RADIO

6.2.4 IRK data structure

The IRK data structure is located in RAM at the memory location specified by the IRKPTR register.

Property Address offset Description

IRK0 0 IRK number 0 (16 bytes)
IRK1 16 IRK number 1 (16 bytes)
.. .. ..
IRK15 240 IRK number 15 (16 bytes)

Table 9: IRK data structure overview

6.2.5 Registers
Instances

Instance Base address Description

AAR 0x4000F000 Accelerated address resolver

4413_417 v1.9 176

 Peripherals

Register overview

Register Offset Description

TASKS_START 0x000 Start resolving addresses based on IRKs specified in the IRK data structure
TASKS_STOP 0x008 Stop resolving addresses
EVENTS_END 0x100 Address resolution procedure complete
EVENTS_RESOLVED 0x104 Address resolved
EVENTS_NOTRESOLVED 0x108 Address not resolved
INTENSET 0x304 Enable interrupt
INTENCLR 0x308 Disable interrupt
STATUS 0x400 Resolution status
ENABLE 0x500 Enable AAR
NIRK 0x504 Number of IRKs
IRKPTR 0x508 Pointer to IRK data structure
ADDRPTR 0x510 Pointer to the resolvable address
SCRATCHPTR 0x514 Pointer to data area used for temporary storage

6.2.5.1 TASKS_START
Address offset: 0x000
Start resolving addresses based on IRKs specified in the IRK data structure

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_START Start resolving addresses based on IRKs specified in the IRK data structure
Trigger 1 Trigger task

6.2.5.2 TASKS_STOP
Address offset: 0x008
Stop resolving addresses

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STOP Stop resolving addresses
Trigger 1 Trigger task

6.2.5.3 EVENTS_END
Address offset: 0x100
Address resolution procedure complete

4413_417 v1.9 177

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_END Address resolution procedure complete
NotGenerated 0 Event not generated
Generated 1 Event generated

6.2.5.4 EVENTS_RESOLVED
Address offset: 0x104
Address resolved

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_RESOLVED Address resolved
NotGenerated 0 Event not generated
Generated 1 Event generated

6.2.5.5 EVENTS_NOTRESOLVED
Address offset: 0x108
Address not resolved

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_NOTRESOLVED Address not resolved
NotGenerated 0 Event not generated
Generated 1 Event generated

6.2.5.6 INTENSET
Address offset: 0x304
Enable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW END Write '1' to enable interrupt for event END
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW RESOLVED Write '1' to enable interrupt for event RESOLVED
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW NOTRESOLVED Write '1' to enable interrupt for event NOTRESOLVED

4413_417 v1.9 178

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.2.5.7 INTENCLR
Address offset: 0x308
Disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW END Write '1' to disable interrupt for event END
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW RESOLVED Write '1' to disable interrupt for event RESOLVED
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW NOTRESOLVED Write '1' to disable interrupt for event NOTRESOLVED
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.2.5.8 STATUS
Address offset: 0x400
Resolution status

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R STATUS [0..15] The IRK that was used last time an address was resolved

6.2.5.9 ENABLE
Address offset: 0x500
Enable AAR

4413_417 v1.9 179

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW ENABLE Enable or disable AAR
Disabled 0 Disable
Enabled 3 Enable

6.2.5.10 NIRK
Address offset: 0x504
Number of IRKs

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A

Reset 0x00000001 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
ID R/W Field Value ID Value Description
A RW NIRK [1..16] Number of Identity Root Keys available in the IRK data structure

6.2.5.11 IRKPTR
Address offset: 0x508
Pointer to IRK data structure

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW IRKPTR Pointer to the IRK data structure

6.2.5.12 ADDRPTR
Address offset: 0x510
Pointer to the resolvable address

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW ADDRPTR Pointer to the resolvable address (6-bytes)

6.2.5.13 SCRATCHPTR
Address offset: 0x514
Pointer to data area used for temporary storage

4413_417 v1.9 180

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW SCRATCHPTR Pointer to a scratch data area used for temporary storage during resolution.
A space of minimum 3 bytes must be reserved.

6.2.6 Electrical specification

6.2.6.1 AAR Electrical Specification

Symbol Description Min. Typ. Max. Units

tAAR Address resolution time per IRK. Total time for several IRKs is given as (1 µs 6 µs
+ n * t_AAR), where n is the number of IRKs. (Given priority to the actual
destination RAM block).
tAAR,8 Time for address resolution of 8 IRKs. (Given priority to the actual destination 49 µs
RAM block).

6.3 ACL — Access control lists

The Access control lists (ACL) peripheral is designed to assign and enforce access permission schemes for
different regions of the on-chip flash memory map.
Flash memory regions can be assigned individual ACL permission schemes. The following registers are
involved:
• PERM register - configures permission schemes
• ADDR register - defines the flash page start address (word-aligned)
• SIZE register - determines the size of the region where the permission schemes are applied

Note: The size of the region is restricted to a multiple of the flash page size, measured in bytes.
The maximum region is limited to half the flash size. See Memory on page 21 for more information.

4413_417 v1.9 181

 Peripherals

On-chip flash memory

l
...
Page N+1 Write
31 ACL[7].ADDR 0
protect
Page N

l 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0

31 ACL[7].SIZE 0

l 0 1
31 ACL[7].PERM 0

...

l Page 3
Read/
31 ACL[0].ADDR 0 Page 2 Write
protect
Page 1

l0 0 1 1 0 0 0 0 0 0 0 0 0 0 0 0 Page 0

31 ACL[0].SIZE 0

l 1 1
31 ACL[0].PERM 0

Figure 30: On-chip flash memory protected regions

There are four defined ACL permission schemes, each with different combinations of read/write
permissions, as shown in the following table.

Read Write Protection description

0 0 No protection. Entire region can be executed, read, written to, or erased.
0 1 Region can be executed and read, but not written to or erased.
1 0 Region can be written to and erased, but not executed or read.
1 1 Region is locked for all access until next reset.

Table 10: ACL permission schemes

Note: If a permission violation to a protected region is detected by the ACL peripheral, the request
is blocked and a Bus Fault exception is triggered.

Access control to a configured region is enforced by the hardware. This goes into effect two CPU clock
cycles after the ADDR, SIZE, and PERM registers for an ACL instance are written successfully. There are two
dependencies for protection to be enforced. First, a valid start address for the flash page boundary must
be written to the ADDR register. Second, the SIZE and PERM registers cannot be zero.

4413_417 v1.9 182

 Peripherals

The ADDR, SIZE, and PERM registers can only be written once. All ACL configuration registers are cleared
on reset by resetting the device from a reset source. This is the only way of clearing the configuration
registers. To ensure that the ACL peripheral always enforces the desired permission schemes, the device
boot sequence must perform the necessary configuration.
Debugger read access to a read-protected region will be Read-As-Zero (RAZ), while debugger write access
to a write-protected region will be Write-Ignored (WI).

6.3.1 Registers
Instances

Instance Base address Description

ACL 0x4001E000 Access control lists

Register overview

Register Offset Description

ACL[0].ADDR 0x800 Start address of region to protect. The start address must be word-aligned.
ACL[0].SIZE 0x804 Size of region to protect counting from address ACL[0].ADDR. Writing a '0' has no effect.
ACL[0].PERM 0x808 Access permissions for region 0 as defined by start address ACL[0].ADDR and size ACL[0].SIZE
ACL[1].ADDR 0x810 Start address of region to protect. The start address must be word-aligned.
ACL[1].SIZE 0x814 Size of region to protect counting from address ACL[1].ADDR. Writing a '0' has no effect.
ACL[1].PERM 0x818 Access permissions for region 1 as defined by start address ACL[1].ADDR and size ACL[1].SIZE
ACL[2].ADDR 0x820 Start address of region to protect. The start address must be word-aligned.
ACL[2].SIZE 0x824 Size of region to protect counting from address ACL[2].ADDR. Writing a '0' has no effect.
ACL[2].PERM 0x828 Access permissions for region 2 as defined by start address ACL[2].ADDR and size ACL[2].SIZE
ACL[3].ADDR 0x830 Start address of region to protect. The start address must be word-aligned.
ACL[3].SIZE 0x834 Size of region to protect counting from address ACL[3].ADDR. Writing a '0' has no effect.
ACL[3].PERM 0x838 Access permissions for region 3 as defined by start address ACL[3].ADDR and size ACL[3].SIZE
ACL[4].ADDR 0x840 Start address of region to protect. The start address must be word-aligned.
ACL[4].SIZE 0x844 Size of region to protect counting from address ACL[4].ADDR. Writing a '0' has no effect.
ACL[4].PERM 0x848 Access permissions for region 4 as defined by start address ACL[4].ADDR and size ACL[4].SIZE
ACL[5].ADDR 0x850 Start address of region to protect. The start address must be word-aligned.
ACL[5].SIZE 0x854 Size of region to protect counting from address ACL[5].ADDR. Writing a '0' has no effect.
ACL[5].PERM 0x858 Access permissions for region 5 as defined by start address ACL[5].ADDR and size ACL[5].SIZE
ACL[6].ADDR 0x860 Start address of region to protect. The start address must be word-aligned.
ACL[6].SIZE 0x864 Size of region to protect counting from address ACL[6].ADDR. Writing a '0' has no effect.
ACL[6].PERM 0x868 Access permissions for region 6 as defined by start address ACL[6].ADDR and size ACL[6].SIZE
ACL[7].ADDR 0x870 Start address of region to protect. The start address must be word-aligned.
ACL[7].SIZE 0x874 Size of region to protect counting from address ACL[7].ADDR. Writing a '0' has no effect.
ACL[7].PERM 0x878 Access permissions for region 7 as defined by start address ACL[7].ADDR and size ACL[7].SIZE

6.3.1.1 ACL[0].ADDR
Address offset: 0x800
Start address of region to protect. The start address must be word-aligned.

Note: This register can only be written once.

4413_417 v1.9 183

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW1 ADDR Start address of flash region 0. The start address must point to a flash page
boundary.

6.3.1.2 ACL[0].SIZE
Address offset: 0x804
Size of region to protect counting from address ACL[0].ADDR. Writing a '0' has no effect.

Note: This register can only be written once.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW1 SIZE Size of flash region 0 in bytes. Must be a multiple of the flash page size.

6.3.1.3 ACL[0].PERM
Address offset: 0x808
Access permissions for region 0 as defined by start address ACL[0].ADDR and size ACL[0].SIZE

Note: This register can only be written once.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW1 WRITE Configure write and erase permissions for region 0. Writing a '0' has no
effect.
Enable 0 Allow write and erase instructions to region 0.
Disable 1 Block write and erase instructions to region 0.
B RW1 READ Configure read permissions for region 0. Writing a '0' has no effect.
Enable 0 Allow read instructions to region 0.
Disable 1 Block read instructions to region 0.

6.3.1.4 ACL[1].ADDR
Address offset: 0x810
Start address of region to protect. The start address must be word-aligned.

Note: This register can only be written once.

4413_417 v1.9 184

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW1 ADDR Start address of flash region 1. The start address must point to a flash page
boundary.

6.3.1.5 ACL[1].SIZE
Address offset: 0x814
Size of region to protect counting from address ACL[1].ADDR. Writing a '0' has no effect.

Note: This register can only be written once.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW1 SIZE Size of flash region 1 in bytes. Must be a multiple of the flash page size.

6.3.1.6 ACL[1].PERM
Address offset: 0x818
Access permissions for region 1 as defined by start address ACL[1].ADDR and size ACL[1].SIZE

Note: This register can only be written once.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW1 WRITE Configure write and erase permissions for region 1. Writing a '0' has no
effect.
Enable 0 Allow write and erase instructions to region 1.
Disable 1 Block write and erase instructions to region 1.
B RW1 READ Configure read permissions for region 1. Writing a '0' has no effect.
Enable 0 Allow read instructions to region 1.
Disable 1 Block read instructions to region 1.

6.3.1.7 ACL[2].ADDR
Address offset: 0x820
Start address of region to protect. The start address must be word-aligned.

Note: This register can only be written once.

4413_417 v1.9 185

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW1 ADDR Start address of flash region 2. The start address must point to a flash page
boundary.

6.3.1.8 ACL[2].SIZE
Address offset: 0x824
Size of region to protect counting from address ACL[2].ADDR. Writing a '0' has no effect.

Note: This register can only be written once.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW1 SIZE Size of flash region 2 in bytes. Must be a multiple of the flash page size.

6.3.1.9 ACL[2].PERM
Address offset: 0x828
Access permissions for region 2 as defined by start address ACL[2].ADDR and size ACL[2].SIZE

Note: This register can only be written once.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW1 WRITE Configure write and erase permissions for region 2. Writing a '0' has no
effect.
Enable 0 Allow write and erase instructions to region 2.
Disable 1 Block write and erase instructions to region 2.
B RW1 READ Configure read permissions for region 2. Writing a '0' has no effect.
Enable 0 Allow read instructions to region 2.
Disable 1 Block read instructions to region 2.

6.3.1.10 ACL[3].ADDR
Address offset: 0x830
Start address of region to protect. The start address must be word-aligned.

Note: This register can only be written once.

4413_417 v1.9 186

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW1 ADDR Start address of flash region 3. The start address must point to a flash page
boundary.

6.3.1.11 ACL[3].SIZE
Address offset: 0x834
Size of region to protect counting from address ACL[3].ADDR. Writing a '0' has no effect.

Note: This register can only be written once.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW1 SIZE Size of flash region 3 in bytes. Must be a multiple of the flash page size.

6.3.1.12 ACL[3].PERM
Address offset: 0x838
Access permissions for region 3 as defined by start address ACL[3].ADDR and size ACL[3].SIZE

Note: This register can only be written once.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW1 WRITE Configure write and erase permissions for region 3. Writing a '0' has no
effect.
Enable 0 Allow write and erase instructions to region 3.
Disable 1 Block write and erase instructions to region 3.
B RW1 READ Configure read permissions for region 3. Writing a '0' has no effect.
Enable 0 Allow read instructions to region 3.
Disable 1 Block read instructions to region 3.

6.3.1.13 ACL[4].ADDR
Address offset: 0x840
Start address of region to protect. The start address must be word-aligned.

Note: This register can only be written once.

4413_417 v1.9 187

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW1 ADDR Start address of flash region 4. The start address must point to a flash page
boundary.

6.3.1.14 ACL[4].SIZE
Address offset: 0x844
Size of region to protect counting from address ACL[4].ADDR. Writing a '0' has no effect.

Note: This register can only be written once.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW1 SIZE Size of flash region 4 in bytes. Must be a multiple of the flash page size.

6.3.1.15 ACL[4].PERM
Address offset: 0x848
Access permissions for region 4 as defined by start address ACL[4].ADDR and size ACL[4].SIZE

Note: This register can only be written once.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW1 WRITE Configure write and erase permissions for region 4. Writing a '0' has no
effect.
Enable 0 Allow write and erase instructions to region 4.
Disable 1 Block write and erase instructions to region 4.
B RW1 READ Configure read permissions for region 4. Writing a '0' has no effect.
Enable 0 Allow read instructions to region 4.
Disable 1 Block read instructions to region 4.

6.3.1.16 ACL[5].ADDR
Address offset: 0x850
Start address of region to protect. The start address must be word-aligned.

Note: This register can only be written once.

4413_417 v1.9 188

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW1 ADDR Start address of flash region 5. The start address must point to a flash page
boundary.

6.3.1.17 ACL[5].SIZE
Address offset: 0x854
Size of region to protect counting from address ACL[5].ADDR. Writing a '0' has no effect.

Note: This register can only be written once.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW1 SIZE Size of flash region 5 in bytes. Must be a multiple of the flash page size.

6.3.1.18 ACL[5].PERM
Address offset: 0x858
Access permissions for region 5 as defined by start address ACL[5].ADDR and size ACL[5].SIZE

Note: This register can only be written once.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW1 WRITE Configure write and erase permissions for region 5. Writing a '0' has no
effect.
Enable 0 Allow write and erase instructions to region 5.
Disable 1 Block write and erase instructions to region 5.
B RW1 READ Configure read permissions for region 5. Writing a '0' has no effect.
Enable 0 Allow read instructions to region 5.
Disable 1 Block read instructions to region 5.

6.3.1.19 ACL[6].ADDR
Address offset: 0x860
Start address of region to protect. The start address must be word-aligned.

Note: This register can only be written once.

4413_417 v1.9 189

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW1 ADDR Start address of flash region 6. The start address must point to a flash page
boundary.

6.3.1.20 ACL[6].SIZE
Address offset: 0x864
Size of region to protect counting from address ACL[6].ADDR. Writing a '0' has no effect.

Note: This register can only be written once.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW1 SIZE Size of flash region 6 in bytes. Must be a multiple of the flash page size.

6.3.1.21 ACL[6].PERM
Address offset: 0x868
Access permissions for region 6 as defined by start address ACL[6].ADDR and size ACL[6].SIZE

Note: This register can only be written once.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW1 WRITE Configure write and erase permissions for region 6. Writing a '0' has no
effect.
Enable 0 Allow write and erase instructions to region 6.
Disable 1 Block write and erase instructions to region 6.
B RW1 READ Configure read permissions for region 6. Writing a '0' has no effect.
Enable 0 Allow read instructions to region 6.
Disable 1 Block read instructions to region 6.

6.3.1.22 ACL[7].ADDR
Address offset: 0x870
Start address of region to protect. The start address must be word-aligned.

Note: This register can only be written once.

4413_417 v1.9 190

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW1 ADDR Start address of flash region 7. The start address must point to a flash page
boundary.

6.3.1.23 ACL[7].SIZE
Address offset: 0x874
Size of region to protect counting from address ACL[7].ADDR. Writing a '0' has no effect.

Note: This register can only be written once.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW1 SIZE Size of flash region 7 in bytes. Must be a multiple of the flash page size.

6.3.1.24 ACL[7].PERM
Address offset: 0x878
Access permissions for region 7 as defined by start address ACL[7].ADDR and size ACL[7].SIZE

Note: This register can only be written once.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW1 WRITE Configure write and erase permissions for region 7. Writing a '0' has no
effect.
Enable 0 Allow write and erase instructions to region 7.
Disable 1 Block write and erase instructions to region 7.
B RW1 READ Configure read permissions for region 7. Writing a '0' has no effect.
Enable 0 Allow read instructions to region 7.
Disable 1 Block read instructions to region 7.

6.4 CCM — AES CCM mode encryption

Cipher block chaining - message authentication code (CCM) mode is an authenticated encryption
algorithm designed to provide both authentication and confidentiality during data transfer. CCM combines
counter mode encryption and CBC-MAC authentication. The CCM terminology "Message authentication
code (MAC)" is called the "Message integrity check (MIC)" in Bluetooth terminology and also in this
document.
The CCM block generates an encrypted keystream that is applied to input data using the XOR operation
and generates the four byte MIC field in one operation. CCM and RADIO can be configured to work
synchronously. CCM will encrypt in time for transmission and decrypt after receiving bytes into memory
from the radio. All operations can complete within the packet RX or TX time. CCM on this device is

4413_417 v1.9 191

 Peripherals

implemented according to Bluetooth requirements and the algorithm as defined in IETF RFC3610, and
depends on the AES-128 block cipher. A description of the CCM algorithm can also be found in NIST
Special Publication 800-38C. The Bluetooth specification describes the configuration of counter mode
blocks and encryption blocks to implement compliant encryption for Bluetooth Low Energy.
The CCM block uses EasyDMA to load key counter mode blocks (including the nonce required), and to
read/write plain text and cipher text.
The AES CCM peripheral supports three operations: keystream generation, packet encryption, and packet
decryption. These operations are performed in compliance with the Bluetooth AES CCM 128 bit block
encryption, see Bluetooth Core specification Version 4.0.
The following figure illustrates keystream generation followed by encryption or decryption. The shortcut is
optional.
keystream
encryption / decryption
generation

KSGEN ENDKSGEN CRYPT ENDCRYPT

SHORTCUT

Figure 31: Keystream generation

6.4.1 Keystream generation

A new keystream needs to be generated before a new packet encryption or packet decryption operation
can start.
A keystream is generated by triggering the KSGEN task. An ENDKSGEN event is generated after the
keystream has been generated.
Keystream generation, packet encryption, and packet decryption operations utilize the configuration
specified in the data structure pointed to by CNFPTR on page 202. It is necessary to configure this
pointer and its underlying data structure, and register MODE on page 201 before the KSGEN task is
triggered.
The keystream will be stored in the AES CCM peripheral’s temporary memory area, specified by the
SCRATCHPTR on page 203, where it will be used in subsequent encryption and decryption operations.
For default length packets (MODE.LENGTH = Default), the size of the generated keystream is 27 bytes.
When using extended length packets (MODE.LENGTH = Extended), register MAXPACKETSIZE on page
203 specifies the length of the keystream to be generated. The length of the generated keystream must
be greater or equal to the length of the subsequent packet payload to be encrypted or decrypted. The
maximum length of the keystream in extended mode is 251 bytes, which means that the maximum packet
payload size is 251.
If a shortcut is used between the ENDKSGEN event and CRYPT task, pointer INPTR on page 202 and the
pointers OUTPTR on page 202 must also be configured before the KSGEN task is triggered.

6.4.2 Encryption
The AES CCM periheral is able to read an unencrypted packet, encrypt it, and append a four byte MIC field
to the packet.
During packet encryption, the AES CCM peripheral performs the following:
• Reads the unencrypted packet located in RAM address specified in the INPTR pointer
• Encrypts the packet
• Appends a four byte long Message Integrity Check (MIC) field to the packet

4413_417 v1.9 192

 Peripherals

Encryption is started by triggering the CRYPT task with register MODE on page 201 set to ENCRYPTION.
An ENDCRYPT event is generated when packet encryption is completed.
The AES CCM peripheral will also modify the length field of the packet to adjust for the appended MIC
field. It adds four bytes to the length and stores the resulting packet in RAM at the address specified in
pointer OUTPTR on page 202, see Encryption on page 193.
Empty packets (length field is set to 0) will not be encrypted but instead moved unmodified through the
AES CCM peripheral.
AES CCM supports different widths of the LENGTH field in the data structure for encrypted packets. This is
configured in register MODE on page 201.
SCRATCHPTR
INPTR

Unencrypted packet
H: Header (S0)
L: Length
H L RFU PL Scratch area
RFU: reserved for future use (S1)
OUTPTR PL: unencrypted payload
Encrypted packet MODE = ENCRYPTION AES CCM EPL: encrypted payload

CCM data
H L+4 RFU EPL MIC
structure

CNFPTR

Figure 32: Encryption

6.4.3 Decryption
The AES CCM peripheral is able to read an encrypted packet, decrypt it, authenticate the MIC field, and
generate an appropriate MIC status.
During packet decryption, the AES CCM peripheral performs the following:
• Reads the encrypted packet located in RAM at the address specified in the INPTR pointer
• Decrypts the packet
• Authenticates the packet's MIC field
• Generates the appropriate MIC status
The packet header (S0) and payload are included in the MIC authentication.
Decryption is started by triggering the CRYPT task with register MODE on page 201 set to DECRYPTION.
An ENDCRYPT event is generated when packet decryption is completed.
The AES CCM peripheral modifies the length field of the packet to adjust for the MIC field. It subtracts
four bytes from the length and stores the decrypted packet in RAM at the address specified in the pointer
OUTPTR, see Decryption on page 194.
CCM is only able to decrypt packet payloads that are at least five bytes long (one byte or more encrypted
payload (EPL) and four bytes of MIC). CCM will therefore generate a MIC error for packets where the
length field is set to 1, 2, 3, or 4.
Empty packets (length field is set to 0) will not be decrypted but instead moved unmodified through the
AES CCM peripheral. These packets will always pass the MIC check.
CCM supports different widths of the LENGTH field in the data structure for decrypted packets. This is
configured in register MODE on page 201.

4413_417 v1.9 193

 Peripherals

SCRATCHPTR
OUTPTR

Unencrypted packet
H: Header (S0)
L: Length
H L RFU PL Scratch area
RFU: reserved for future use (S1)
INPTR PL: unencrypted payload
Encrypted packet MODE = DECRYPTION AES CCM EPL: encrypted payload

CCM data
H L+4 RFU EPL MIC
structure

CNFPTR

Figure 33: Decryption

6.4.4 AES CCM and RADIO concurrent operation

The CCM peripheral is able to encrypt/decrypt data synchronously to data being transmitted or received
on the radio.
In order for CCM to run synchronously with the radio, the data rate setting in register MODE on page
201 needs to match the radio data rate. The settings in this register apply whenever either the KSGEN or
CRYPT tasks are triggered.
The data rate setting of register MODE on page 201 can also be overridden on-the-fly during an ongoing
encrypt/decrypt operation by the contents of register RATEOVERRIDE on page 203. The data rate setting
in this register applies whenever the RATEOVERRIDE task is triggered. This feature can be useful in cases
where the radio data rate is changed during an ongoing packet transaction.

6.4.5 Encrypting packets on-the-fly in radio transmit mode

When the AES CCM peripheral encrypts a packet on-the-fly while RADIO is transmitting it, RADIO must
read the encrypted packet from the same memory location that the AES CCM peripheral is writing to.
The OUTPTR on page 202 pointer in the AES CCM must point to the same memory location as the
PACKETPTR pointer in the radio, see Configuration of on-the-fly encryption on page 194.
SCRATCHPTR
INPTR

Unencrypted packet
H: Header (S0)
L: Length
OUTPTR H L RFU PL Scratch area
RFU: reserved for future use (S1)
& PL: unencrypted payload
PACKETPTR MODE = ENCRYPTION AES CCM EPL: encrypted payload
Encrypted packet

CCM data
H L+4 RFU EPL MIC
structure

CNFPTR
To remote
receiver
RADIO
TXEN

Figure 34: Configuration of on-the-fly encryption

In order to match RADIO’s timing, the KSGEN task must be triggered early enough to allow the keystream
generation to complete before packet encryption begins.
For short packets (MODE.LENGTH = Default), the KSGEN task must be triggered before or at the same
time as the START task in RADIO is triggered. In addition, the shortcut between the ENDKSGEN event and
the CRYPT task must be enabled. This use-case is illustrated in On-the-fly encryption of short packets
(MODE.LENGTH = Default) using a PPI connection on page 195. It uses a PPI connection between the
READY event in RADIO and the KSGEN task in the AES CCM peripheral.
For long packets (MODE.LENGTH = Extended), the keystream generation needs to start earlier, such as
when the TXEN task in RADIO is triggered.
Refer to Timing specification on page 204 for information about the time needed for generating a
keystream.

4413_417 v1.9 194

 Peripherals

SHORTCUT

ENDKSGEN CRYPT

keystream
AES CCM encryption
generation

KSGEN ENDCRYPT

PPI

READY

RADIO RU P A H L RFU EPL MIC CRC

TXEN END

READY START

RU: Ramp-up of RADIO H: Header (S0) EPL: encrypted payload

P: Preamble SHORTCUT L: Length
A: Address RFU: reserved for future use (S1)

Figure 35: On-the-fly encryption of short packets (MODE.LENGTH = Default) using a PPI connection

6.4.6 Decrypting packets on-the-fly in RADIO receive mode

When the AES CCM peripheral decrypts a packet on-the-fly while RADIO is receiving it, the AES CCM
peripheral must read the encrypted packet from the same memory location that RADIO is writing to.
The INPTR on page 202 pointer in the AES CCM must point to the same memory location as the
PACKETPTR pointer in RADIO, see Configuration of on-the-fly decryption on page 195.
SCRATCHPTR
OUTPTR

Unencrypted packet
H: Header (S0)
L: Length
INPTR H L RFU PL Scratch area
RFU: reserved for future use (S1)
& PL: unencrypted payload
PACKETPTR MODE = DECRYPTION AES CCM EPL: encrypted payload
Encrypted packet

CCM data
H L+4 RFU EPL MIC
structure

CNFPTR
From remote
transmitter
RADIO
RXEN

Figure 36: Configuration of on-the-fly decryption

In order to match RADIO’s timing, the KSGEN task must be triggered early enough to allow the keystream
generation to complete before the decryption of the packet shall start.
For short packets (MODE.LENGTH = Default) the KSGEN task must be triggered no later than when the
START task in RADIO is triggered. In addition, the CRYPT task must be triggered no earlier than when the
ADDRESS event is generated by RADIO.
If the CRYPT task is triggered exactly at the same time as the ADDRESS event is generated by RADIO, the
AES CCM peripheral will guarantee that the decryption is completed no later than when the END event in
RADIO is generated.
This use-case is illustrated in On-the-fly decryption of short packets (MODE.LENGTH = Default) using a PPI
connection on page 196 using a PPI connection between the ADDRESS event in RADIO and the CRYPT
task in the AES CCM peripheral. The KSGEN task is triggered from the READY event in RADIO through a PPI
connection.
For long packets (MODE.LENGTH = Extended) the keystream generation will need to start even earlier,
such as when the RXEN task in RADIO is triggered.

4413_417 v1.9 195

 Peripherals

Refer to Timing specification on page 204 for information about the time needed for generating a
keystream.
keystream
AES CCM decryption
generation

KSGEN ENDKSGEN CRYPT ENDCRYPT

PPI PPI

READY ADDRESS

RADIO RU P A H L RFU EPL MIC CRC

RXEN END

READY START

SHORTCUT
RU: Ramp-up of RADIO H: Header (S0) EPL: encrypted payload
P: Preamble L: Length : RADIO receiving noise
A: Address RFU: reserved for future use (S1)

Figure 37: On-the-fly decryption of short packets (MODE.LENGTH = Default) using a PPI connection

6.4.7 CCM data structure

The CCM data structure is located in Data RAM at the memory location specified by the CNFPTR pointer
register.

Property Address offset Description

KEY 0 16 byte AES key
PKTCTR 16 Octet0 (LSO) of packet counter
17 Octet1 of packet counter
18 Octet2 of packet counter
19 Octet3 of packet counter
20 Bit 6 – Bit 0: Octet4 (7 most significant bits of packet counter, with Bit 6 being the most
significant bit) Bit7: Ignored
21 Ignored
22 Ignored
23 Ignored
24 Bit 0: Direction bit Bit 7 – Bit 1: Zero padded
IV 25 8 byte initialization vector (IV) Octet0 (LSO) of IV, Octet1 of IV, … , Octet7 (MSO) of IV

Table 11: CCM data structure overview

The NONCE vector (as specified by the Bluetooth Core Specification) will be generated by hardware based
on the information specified in the CCM data structure from CCM data structure overview on page 196 .

Property Address offset Description

HEADER 0 Packet Header
LENGTH 1 Number of bytes in unencrypted payload
RFU 2 Reserved Future Use
PAYLOAD 3 Unencrypted payload

Table 12: Data structure for unencrypted packet

4413_417 v1.9 196

 Peripherals

Property Address offset Description

HEADER 0 Packet Header
LENGTH 1 Number of bytes in encrypted payload including length of MIC

LENGTH will be 0 for empty packets since the MIC is not added to empty packets
RFU 2 Reserved Future Use
PAYLOAD 3 Encrypted payload
MIC 3 + payload length ENCRYPT: 4 bytes encrypted MIC

MIC is not added to empty packets

Table 13: Data structure for encrypted packet

6.4.8 EasyDMA and ERROR event

CCM implements an EasyDMA mechanism for reading and writing to RAM.
When the CPU and EasyDMA enabled peripherals access the same RAM block at the same time, increased
bus collisions might disrupt on-the-fly encryption. This will generate an ERROR event.
EasyDMA stops accessing RAM when the ENDKSGEN and ENDCRYPT events are generated.
If the CNFPTR, SCRATCHPTR, INPTR, and the OUTPTR are not pointing to the Data RAM region, an
EasyDMA transfer may result in a HardFault or RAM corruption. See Memory on page 21 for more
information about the different memory regions.

6.4.9 Registers
Instances

Instance Base address Description

CCM 0x4000F000 AES counter with CBC-MAC (CCM) mode block encryption

Register overview

Register Offset Description

TASKS_KSGEN 0x000 Start generation of keystream. This operation will stop by itself when completed.
TASKS_CRYPT 0x004 Start encryption/decryption. This operation will stop by itself when completed.
TASKS_STOP 0x008 Stop encryption/decryption
TASKS_RATEOVERRIDE 0x00C Override DATARATE setting in MODE register with the contents of the RATEOVERRIDE register for any
ongoing encryption/decryption
EVENTS_ENDKSGEN 0x100 Keystream generation complete
EVENTS_ENDCRYPT 0x104 Encrypt/decrypt complete
EVENTS_ERROR 0x108 CCM error event

This register is deprecated.

SHORTS 0x200 Shortcuts between local events and tasks
INTENSET 0x304 Enable interrupt
INTENCLR 0x308 Disable interrupt
MICSTATUS 0x400 MIC check result
ENABLE 0x500 Enable
MODE 0x504 Operation mode
CNFPTR 0x508 Pointer to data structure holding the AES key and the NONCE vector
INPTR 0x50C Input pointer
OUTPTR 0x510 Output pointer
SCRATCHPTR 0x514 Pointer to data area used for temporary storage

4413_417 v1.9 197

 Peripherals

Register Offset Description

MAXPACKETSIZE 0x518 Length of keystream generated when MODE.LENGTH = Extended
RATEOVERRIDE 0x51C Data rate override setting.

6.4.9.1 TASKS_KSGEN
Address offset: 0x000
Start generation of keystream. This operation will stop by itself when completed.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_KSGEN Start generation of keystream. This operation will stop by itself when
completed.
Trigger 1 Trigger task

6.4.9.2 TASKS_CRYPT
Address offset: 0x004
Start encryption/decryption. This operation will stop by itself when completed.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_CRYPT Start encryption/decryption. This operation will stop by itself when
completed.
Trigger 1 Trigger task

6.4.9.3 TASKS_STOP
Address offset: 0x008
Stop encryption/decryption

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STOP Stop encryption/decryption
Trigger 1 Trigger task

6.4.9.4 TASKS_RATEOVERRIDE
Address offset: 0x00C
Override DATARATE setting in MODE register with the contents of the RATEOVERRIDE register for any
ongoing encryption/decryption

4413_417 v1.9 198

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_RATEOVERRIDE Override DATARATE setting in MODE register with the contents of the
RATEOVERRIDE register for any ongoing encryption/decryption
Trigger 1 Trigger task

6.4.9.5 EVENTS_ENDKSGEN
Address offset: 0x100
Keystream generation complete

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_ENDKSGEN Keystream generation complete
NotGenerated 0 Event not generated
Generated 1 Event generated

6.4.9.6 EVENTS_ENDCRYPT
Address offset: 0x104
Encrypt/decrypt complete

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_ENDCRYPT Encrypt/decrypt complete
NotGenerated 0 Event not generated
Generated 1 Event generated

6.4.9.7 EVENTS_ERROR (Deprecated)

Address offset: 0x108
CCM error event
This register is deprecated.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_ERROR CCM error event

This field is deprecated.

NotGenerated 0 Event not generated
Generated 1 Event generated

4413_417 v1.9 199

 Peripherals

6.4.9.8 SHORTS
Address offset: 0x200
Shortcuts between local events and tasks

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW ENDKSGEN_CRYPT Shortcut between event ENDKSGEN and task CRYPT
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut

6.4.9.9 INTENSET
Address offset: 0x304
Enable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW ENDKSGEN Write '1' to enable interrupt for event ENDKSGEN
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW ENDCRYPT Write '1' to enable interrupt for event ENDCRYPT
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW ERROR Write '1' to enable interrupt for event ERROR

This register is deprecated.

Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.4.9.10 INTENCLR
Address offset: 0x308
Disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW ENDKSGEN Write '1' to disable interrupt for event ENDKSGEN
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW ENDCRYPT Write '1' to disable interrupt for event ENDCRYPT
Clear 1 Disable

4413_417 v1.9 200

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW ERROR Write '1' to disable interrupt for event ERROR

This register is deprecated.

Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.4.9.11 MICSTATUS
Address offset: 0x400
MIC check result

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R MICSTATUS The result of the MIC check performed during the previous decryption
operation
CheckFailed 0 MIC check failed
CheckPassed 1 MIC check passed

6.4.9.12 ENABLE
Address offset: 0x500
Enable

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW ENABLE Enable or disable CCM
Disabled 0 Disable
Enabled 2 Enable

6.4.9.13 MODE
Address offset: 0x504
Operation mode

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B B A

Reset 0x00000001 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
ID R/W Field Value ID Value Description
A- RW MODE The mode of operation to be used. Settings in this register apply whenever
either the KSGEN task or the CRYPT task is triggered.
Encryption 0 AES CCM packet encryption mode

4413_417 v1.9 201

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B B A

Reset 0x00000001 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
ID R/W Field Value ID Value Description
Decryption 1 AES CCM packet decryption mode
B RW DATARATE Radio data rate that the CCM shall run synchronous with
1Mbit 0 1 Mbps
2Mbit 1 2 Mbps
125Kbps 2 125 kbps
500Kbps 3 500 kbps
C RW LENGTH Packet length configuration
Default 0 Default length. Effective length of LENGTH field in encrypted/decrypted
packet is 5 bits. A keystream for packet payloads up to 27 bytes will be
generated.
Extended 1 Extended length. Effective length of LENGTH field in encrypted/decrypted
packet is 8 bits. A keystream for packet payloads up to MAXPACKETSIZE
bytes will be generated.

6.4.9.14 CNFPTR
Address offset: 0x508
Pointer to data structure holding the AES key and the NONCE vector

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW CNFPTR Pointer to the data structure holding the AES key and the CCM NONCE
vector (see table CCM data structure overview)

6.4.9.15 INPTR
Address offset: 0x50C
Input pointer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW INPTR Input pointer

6.4.9.16 OUTPTR
Address offset: 0x510
Output pointer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW OUTPTR Output pointer

4413_417 v1.9 202

 Peripherals

6.4.9.17 SCRATCHPTR
Address offset: 0x514
Pointer to data area used for temporary storage

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW SCRATCHPTR Pointer to a scratch data area used for temporary storage during keystream
generation, MIC generation and encryption/decryption.

The scratch area is used for temporary storage of data during keystream
generation and encryption.

When MODE.LENGTH = Default, a space of 43 bytes is required for this

temporary storage. When MODE.LENGTH = Extended, a space of (16 +
MAXPACKETSIZE) bytes is required.

6.4.9.18 MAXPACKETSIZE
Address offset: 0x518
Length of keystream generated when MODE.LENGTH = Extended

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A

Reset 0x000000FB 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0 1 1
ID R/W Field Value ID Value Description
A RW MAXPACKETSIZE [0x001B..0x00FB] Length of keystream generated when MODE.LENGTH = Extended. This value
must be greater than or equal to the subsequent packet payload to be
encrypted/decrypted.

6.4.9.19 RATEOVERRIDE
Address offset: 0x51C
Data rate override setting.
Override value to be used instead of the setting of MODE.DATARATE. This override value applies when the
RATEOVERRIDE task is triggered.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW RATEOVERRIDE Data rate override setting
1Mbit 0 1 Mbps
2Mbit 1 2 Mbps
125Kbps 2 125 kbps
500Kbps 3 500 kbps

4413_417 v1.9 203

 Peripherals

6.4.10 Electrical specification

6.4.10.1 Timing specification

Symbol Description Min. Typ. Max. Units

tkgen Time needed for keystream generation (given priority access to destination 50 µs
RAM block)

6.5 COMP — Comparator

The comparator (COMP) compares an input voltage (VIN+) against a second input voltage (VIN-). VIN+ can
be derived from an analog input pin (AIN0-AIN7). VIN- can be derived from multiple sources depending on
the operation mode of the comparator.
The main features of COMP are the following:
• Input range from 0 V to VDD
• Single-ended mode
• Fully flexible hysteresis using a 64-level reference ladder
• Differential mode
• Configurable hysteresis
• Reference inputs (VREF):
• VDD
• External reference from AIN0 to AIN7 (between 0 V and VDD)
• Internal references 1.2 V, 1.8 V, and 2.4 V
• Three speed/power consumption modes:
• Low-power
• Normal
• High-speed
• Event generation on output changes
• UP event on VIN- > VIN+
• DOWN event on VIN- < VIN+
• CROSS event on VIN+ and VIN- crossing
• READY event on core and internal reference (if used) ready

4413_417 v1.9 204

 Peripherals

AIN0
AIN1
AIN2
AIN3
AIN4
AIN5
AIN6
AIN7
MUX PSEL

SAMPLE
START

STOP
VIN+ VIN-
+ -

Comparator
MODE
core HYST

RESULT Output
0 = BELOW (VIN+ < VIN-)
1 = ABOVE (VIN+ > VIN-)

READY
DOWN
CROSS
UP

Figure 38: Comparator overview

Once enabled (using the ENABLE register), the comparator is started by triggering the START task and
stopped by triggering the STOP task. The comparator will generate a READY event to indicate when it is
ready for use and the output is correct. The delay between START and READY is tINT_REF,START if an internal
reference is selected, or t COMP,START if an external reference is used. When the COMP module is started,
events will be generated every time VIN+ crosses VIN-.

Operation modes
The comparator can be configured to operate in two main operation modes: differential mode and single-
ended mode. See the MODE register for more information. In both operation modes, the comparator can
operate in different speed and power consumption modes (low-power, normal and high-speed). High-
speed mode will consume more power compared to low-power mode, and low-power mode will result in
slower response time compared to high-speed mode.
Use the PSEL register to select any of the AIN0-AIN7 pins as VIN+ input, regardless of the operation mode
selected for the comparator. The source of VIN- depends on which of the following operation mode are
used:
• Differential mode - Derived directly from AIN0 to AIN7
• Single-ended mode - Derived from VREF. VREF can be derived from VDD, AIN0-AIN7 or internal 1.2 V,
1.8 V and 2.4 V references.
The selected analog pins will be acquired by the comparator once it is enabled.
An optional hysteresis on VIN+ and VIN- can be enabled when the module is used in differential mode
through the HYST register. In single-ended mode, VUP and VDOWN thresholds can be set to implement
a hysteresis using the reference ladder (see Comparator in single-ended mode on page 207). This
hysteresis is in the order of magnitude of VDIFFHYST, and shall prevent noise on the signal to create
unwanted events. See Hysteresis example where VIN+ starts below VUP on page 208 for an illustration
of the effect of an active hysteresis on a noisy input signal.
An upward crossing will generate an UP event and a downward crossing will generate a DOWN event. The
CROSS event will be generated every time there is a crossing, independent of direction.
The immediate value of the comparator can be sampled to RESULT register by triggering the SAMPLE task.

4413_417 v1.9 205

 Peripherals

6.5.1 Differential mode

In differential mode, the reference input VIN- is derived directly from one of the AINx pins.
Before enabling the comparator via the ENABLE register, the following registers must be configured for the
differential mode:
• PSEL
• MODE
• EXTREFSEL
AIN0
AIN1
AIN2
AIN3
AIN4
AIN5
AIN6

AIN0
AIN1
AIN2
AIN3
AIN4
AIN5
AIN6
AIN7
AIN7
MUX PSEL EXTREFSEL MUX

SAMPLE
START

STOP

VIN+
VIN-
+ -

Comparator
MODE
core

RESULT
Output
0 = BELOW (VIN+ < VIN-)
1 = ABOVE (VIN+ > VIN-)
READY
DOWN
CROSS
UP

Figure 39: Comparator in differential mode

Note: Depending on the device, not all the analog inputs may be available for each MUX. See
definitions for PSEL and EXTREFSEL for more information about which analog pins are available on a
particular device.

When the HYST register is turned on during this mode, the output of the comparator and associated
events do the following:
• Change from ABOVE to BELOW when VIN+ drops below VIN- - (VDIFFHYST/2)
• Change from BELOW to ABOVE when VIN+ raises above VIN- + (VDIFFHYST/2)
This behavior is illustrated in the following figure.

VIN+

VIN- + (VDIFFHYST / 2)

VIN- - (VDIFFHYST / 2)

ABOVE BELOW ABOVE BELOW

Output (VIN+ > (VIN- + VDIFFHYST /2)) (VIN+ < (VIN- - VDIFFHYST /2)) (VIN+ > (VIN- + VDIFFHYST /2))

Figure 40: Hysteresis enabled in differential mode

4413_417 v1.9 206

 Peripherals

6.5.2 Single-ended mode

In single-ended mode, VIN- is derived from the reference ladder.
Before enabling the comparator via the ENABLE register, the following registers must be configured for the
single-ended mode:
• PSEL
• MODE
• REFSEL
• EXTREFSEL
• TH
The reference ladder uses the reference voltage (VREF) to derive two new voltage references, VUP and
VDOWN. VUP and VDOWN are configured using THUP and THDOWN respectively in the TH register. VREF
can be derived from any of the available reference sources, configured using the EXTREFSEL and REFSEL
registers as shown in the following figure. When AREF is selected in the REFSEL register, the EXTREFSEL
register is used to select one of the AIN0-AIN7 analog input pins as reference input. The selected analog
pins will be acquired by the comparator once it is enabled.
AIN0
AIN1
AIN2
AIN3
AIN4
AIN5
AIN6
AIN7

AIN0
AIN1
AIN2
AIN3
AIN4
AIN5
AIN6
AIN7
MUX PSEL TH REFSEL EXTREFSEL MUX
SAMPLE
START

STOP

VDD
VUP
VIN+ 0
VIN- AREF
+ - MUX
VDOWN
Comparator 1 Reference VREF 1V2
MODE MUX
core HYST ladder
1V8

RESULT 2V4
Output
0 = BELOW (VIN+ < VIN-)
1 = ABOVE (VIN+ > VIN-)
READY
DOWN
CROSS
UP

Figure 41: Comparator in single-ended mode

Note: Depending on the device, not all the analog inputs may be available for each MUX. See
definitions for PSEL and EXTREFSEL for more information about which analog pins are available on a
particular device.

When the comparator core detects that VIN+ > VIN-, i.e. ABOVE as per the RESULT register, VIN- will switch
to VDOWN. When VIN+ falls below VIN- again, VIN- will be switched back to VUP. By specifying VUP larger
than VDOWN, a hysteresis can be generated as illustrated in the following figures.
Writing to HYST has no effect in single-ended mode, and the content of this register is ignored.

4413_417 v1.9 207

 Peripherals

VIN+

VUP

VDOWN

t
Output

BELOW (VIN+ < VIN-) ABOVE (VIN+ > VIN-) BELOW

VIN-

VUP VDOWN VUP

RESULT

BELOW ABOVE
READY

DOWN
UP

1 2 3
CPU

SAMPLE
SAMPLE
START

Figure 42: Hysteresis example where VIN+ starts below VUP

VIN+

VUP

VDOWN

t
Output

ABOVE (VIN+ > VIN-) BELOW ( VIN+ < VIN-) ABOVE (VIN+ > VIN-) BELOW
VIN-

VDOWN VUP VDOWN VUP

RESULT

ABOVE BELOW ABOVE

READY

DOWN

DOWN
UP

1 2 3
CPU

SAMPLE

SAMPLE
START

Figure 43: Hysteresis example where VIN+ starts above VUP

6.5.3 Registers
Instances

Instance Base address Description

COMP 0x40013000 General purpose comparator

4413_417 v1.9 208

 Peripherals

Register overview

Register Offset Description

TASKS_START 0x000 Start comparator
TASKS_STOP 0x004 Stop comparator
TASKS_SAMPLE 0x008 Sample comparator value
EVENTS_READY 0x100 COMP is ready and output is valid
EVENTS_DOWN 0x104 Downward crossing
EVENTS_UP 0x108 Upward crossing
EVENTS_CROSS 0x10C Downward or upward crossing
SHORTS 0x200 Shortcuts between local events and tasks
INTEN 0x300 Enable or disable interrupt
INTENSET 0x304 Enable interrupt
INTENCLR 0x308 Disable interrupt
RESULT 0x400 Compare result
ENABLE 0x500 COMP enable
PSEL 0x504 Pin select
REFSEL 0x508 Reference source select for single-ended mode
EXTREFSEL 0x50C External reference select
TH 0x530 Threshold configuration for hysteresis unit
MODE 0x534 Mode configuration
HYST 0x538 Comparator hysteresis enable

6.5.3.1 TASKS_START
Address offset: 0x000
Start comparator

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_START Start comparator
Trigger 1 Trigger task

6.5.3.2 TASKS_STOP
Address offset: 0x004
Stop comparator

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STOP Stop comparator
Trigger 1 Trigger task

6.5.3.3 TASKS_SAMPLE
Address offset: 0x008
Sample comparator value

4413_417 v1.9 209

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_SAMPLE Sample comparator value
Trigger 1 Trigger task

6.5.3.4 EVENTS_READY
Address offset: 0x100
COMP is ready and output is valid

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_READY COMP is ready and output is valid
NotGenerated 0 Event not generated
Generated 1 Event generated

6.5.3.5 EVENTS_DOWN
Address offset: 0x104
Downward crossing

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_DOWN Downward crossing
NotGenerated 0 Event not generated
Generated 1 Event generated

6.5.3.6 EVENTS_UP
Address offset: 0x108
Upward crossing

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_UP Upward crossing
NotGenerated 0 Event not generated
Generated 1 Event generated

6.5.3.7 EVENTS_CROSS
Address offset: 0x10C
Downward or upward crossing

4413_417 v1.9 210

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_CROSS Downward or upward crossing
NotGenerated 0 Event not generated
Generated 1 Event generated

6.5.3.8 SHORTS
Address offset: 0x200
Shortcuts between local events and tasks

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW READY_SAMPLE Shortcut between event READY and task SAMPLE
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
B RW READY_STOP Shortcut between event READY and task STOP
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
C RW DOWN_STOP Shortcut between event DOWN and task STOP
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
D RW UP_STOP Shortcut between event UP and task STOP
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
E RW CROSS_STOP Shortcut between event CROSS and task STOP
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut

6.5.3.9 INTEN
Address offset: 0x300
Enable or disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW READY Enable or disable interrupt for event READY
Disabled 0 Disable
Enabled 1 Enable
B RW DOWN Enable or disable interrupt for event DOWN
Disabled 0 Disable
Enabled 1 Enable
C RW UP Enable or disable interrupt for event UP
Disabled 0 Disable
Enabled 1 Enable
D RW CROSS Enable or disable interrupt for event CROSS
Disabled 0 Disable

4413_417 v1.9 211

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Enabled 1 Enable

6.5.3.10 INTENSET
Address offset: 0x304
Enable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW READY Write '1' to enable interrupt for event READY
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW DOWN Write '1' to enable interrupt for event DOWN
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW UP Write '1' to enable interrupt for event UP
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
D RW CROSS Write '1' to enable interrupt for event CROSS
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.5.3.11 INTENCLR
Address offset: 0x308
Disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW READY Write '1' to disable interrupt for event READY
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW DOWN Write '1' to disable interrupt for event DOWN
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW UP Write '1' to disable interrupt for event UP
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

4413_417 v1.9 212

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
D RW CROSS Write '1' to disable interrupt for event CROSS
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.5.3.12 RESULT
Address offset: 0x400
Compare result

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R RESULT Result of last compare. Decision point SAMPLE task.
Below 0 Input voltage is below the threshold (VIN+ < VIN-)
Above 1 Input voltage is above the threshold (VIN+ > VIN-)

6.5.3.13 ENABLE
Address offset: 0x500
COMP enable

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW ENABLE Enable or disable COMP
Disabled 0 Disable
Enabled 2 Enable

6.5.3.14 PSEL
Address offset: 0x504
Pin select

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PSEL Analog pin select
AnalogInput0 0 AIN0 selected as analog input
AnalogInput1 1 AIN1 selected as analog input
AnalogInput2 2 AIN2 selected as analog input
AnalogInput3 3 AIN3 selected as analog input
AnalogInput4 4 AIN4 selected as analog input
AnalogInput5 5 AIN5 selected as analog input
AnalogInput6 6 AIN6 selected as analog input

4413_417 v1.9 213

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
AnalogInput7 7 AIN7 selected as analog input

6.5.3.15 REFSEL
Address offset: 0x508
Reference source select for single-ended mode

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A

Reset 0x00000004 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0
ID R/W Field Value ID Value Description
A RW REFSEL Reference select
Int1V2 0 VREF = internal 1.2 V reference (VDD >= 1.7 V)
Int1V8 1 VREF = internal 1.8 V reference (VDD >= VREF + 0.2 V)
Int2V4 2 VREF = internal 2.4 V reference (VDD >= VREF + 0.2 V)
VDD 4 VREF = VDD
ARef 5 VREF = AREF

6.5.3.16 EXTREFSEL
Address offset: 0x50C
External reference select

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EXTREFSEL External analog reference select
AnalogReference0 0 Use AIN0 as external analog reference
AnalogReference1 1 Use AIN1 as external analog reference
AnalogReference2 2 Use AIN2 as external analog reference
AnalogReference3 3 Use AIN3 as external analog reference
AnalogReference4 4 Use AIN4 as external analog reference
AnalogReference5 5 Use AIN5 as external analog reference
AnalogReference6 6 Use AIN6 as external analog reference
AnalogReference7 7 Use AIN7 as external analog reference

6.5.3.17 TH
Address offset: 0x530
Threshold configuration for hysteresis unit

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B B B B B B A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW THDOWN [63:0] VDOWN = (THDOWN+1)/64*VREF
B RW THUP [63:0] VUP = (THUP+1)/64*VREF

4413_417 v1.9 214

 Peripherals

6.5.3.18 MODE
Address offset: 0x534
Mode configuration

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW SP Speed and power modes
Low 0 Low-power mode
Normal 1 Normal mode
High 2 High-speed mode
B RW MAIN Main operation modes
SE 0 Single-ended mode
Diff 1 Differential mode

6.5.3.19 HYST
Address offset: 0x538
Comparator hysteresis enable

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW HYST Comparator hysteresis
NoHyst 0 Comparator hysteresis disabled
Hyst50mV 1 Comparator hysteresis enabled

6.5.4 Electrical specification

6.5.4.1 COMP Electrical Specification

Symbol Description Min. Typ. Max. Units

tPROPDLY,LP Propagation delay, Low-power mode 15 0.6 µs

tPROPDLY,N Propagation delay, Normal mode 15 0.2 µs

tPROPDLY,HS Propagation delay, High-speed mode15 0.1 µs

VDIFFHYST Optional hysteresis applied to differential input 20 30 80 mV

VVDD-VREF Required difference between VDD and a selected VREF, VDD > VREF 0.3 V
tINT_REF,START Startup time for the internal bandgap reference 50 80 µs
EINT_REF Internal bandgap reference error -3 3 %
VINPUTOFFSET Input offset -10 10 mV
tCOMP,START Startup time for the comparator core 3 µs

15
Propagation delay is with 10 mV overdrive.

4413_417 v1.9 215

 Peripherals

6.6 CRYPTOCELL — Arm TrustZone CryptoCell 310

Arm TrustZone CryptoCell 310 (CRYPTOCELL) is a security peripheral that provides root of trust (RoT) and
cryptographic services for a device.

Flash Data RAM

ARM Cortex CPU
CRYPTOCELL
CRYPTOCELL library
workspace

AHB multilayer

Public key
DMA
Engine control logic

SRAM accelerator
engine

Data routing AHB-APB bridge

SRAM TRNG

Control AES HASH ChaCha

Always-on
domain interface

CRYPTOCELL

APB

Figure 44: Block diagram for CRYPTOCELL

4413_417 v1.9 216

 Peripherals

Feature Description
True random number generator (TRNG) NIST 800-90B, AIS-31, and FIPS 140-2 compliant
Pseudorandom number generator (PRNG) AES engine compliant with NIST 800-90A
RSA public key cryptography Up to 2048-bit key size

PKCS#1 v2.1/v1.5

Optional CRT support

Elliptic curve cryptography (ECC) • NIST FIPS 186-4 recommended curves using pseudorandom parameters, up to 521 bits:
Prime field - P-192, P-224, P-256, P-384, P-521

• SEC 2 recommended curves using pseudorandom parameters, up to 521 bits: Prime field -
secp160r1, secp192r1, secp224r1, secp256r1, secp384r1, secp521r1

• Koblitz curves using fixed parameters, up to 256 bits: Prime field - secp160k1, secp192k1,
secp224k1, secp256k1

• Edwards/Montgomery curves: Ed25519, Curve25519

• ECDH/ECDSA
Secure remote password protocol (SRP) Up to 3072-bit operations
Hashing functions SHA-1, SHA-2 up to 256 bits

Keyed-hash message authentication code (HMAC)

AES symmetric encryption General purpose AES engine (encrypt/decrypt, sign/verify)

128-bit key size

Supported encryption modes: ECB, CBC, CMAC/CBC-MAC, CTR, CCM/CCM* (CCM* is a minor
variation of CCM)
ChaCha20/Poly1305 symmetric encryption Supported key size: 128 bits and 256 bits

Authenticated encryption with associated data (AEAD) mode

Table 14: CRYPTOCELL features

6.6.1 Usage
The CRYPTOCELL peripheral is enabled by a register interface. Access to CRYPTOCELL cryptographic
functions are available in a software library found in the device's SDK. These are not available through a
register interface.
To enable CRYPTOCELL, use register ENABLE on page 220.

Note: The device is prevented from entering the System ON, All Idle state when CRYPTOCELL is
enabled.

6.6.2 Always-on (AO) power domain

CRYPTOCELL has an internal always-on (AO) power domain for retaining device secrets when CRYPTOCELL
is disabled.
The following information is retained by the AO power domain:
• 4 bits indicating the configured CRYPTOCELL life cycle state (LCS)
• 1 bit indicating if the hard-coded RTL key, KPRTL, is available (see RTL key on page 218)
• 128-bit device root key, KDR (see Device root key on page 218)
A reset from any reset source erases the AO power domain content.

6.6.3 Life cycle state (LCS)

Life cycle refers to multiple states a device goes through during its lifetime. DEBUG and SECURE are the
two life cycle states available to the device.

4413_417 v1.9 217

 Peripherals

The CRYPTOCELL life cycle state (LCS) is controlled through register HOST_IOT_LCS on page 223.
Configure LCS by writing either Debug or Secure to the LCS field of this register. To validate that
the register is configured correctly, read back the read-only field LCS_IS_VALID from the register
HOST_IOT_LCS on page 223. The LCS_IS_VALID field will change from Invalid to Valid once a valid
LCS value is written.

LCS field value LCS_IS_VALID field value Description

Secure Invalid Default reset value indicating that LCS has not been configured.
Secure Valid LCS set to SECURE mode, and LCS is valid. Registers HOST_IOT_KDR[0..3] can only be written once per reset
cycle. Any additional writes are ignored.
Debug Valid LCS set to DEBUG mode, and LCS is valid. Registers HOST_IOT_KDR[0..3] can be written multiple times.

Table 15: Life cycle states

6.6.4 Cryptographic key selection

CRYPTOCELL can operate with different cryptographic keys.
Register HOST_CRYPTOKEY_SEL on page 221 selects one of the following keys for cryptographic
operations:
• RTL key KPRTL
• Device root key KDR
• Session key
KPRTL and KDR are configured as part of the CRYPTOCELL initialization process. The application provides
session keys through the API library.

6.6.4.1 RTL key

CRYPTOCELL has one hard-coded RTL key called KPRTL. This key is set to the same value for all devices with
the same part code and cannot be changed.
CRYPTOCELL requests the KPRTL key for cryptographic operations, without revealing the key value. Access
to KPRTL can be disabled until next reset by writing to register HOST_IOT_KPRTL_LOCK on page 221. If a
locked KPRTL key is requested, a zero vector key will be routed to the AES engine instead.

6.6.4.2 Device root key

The device root key, KDR, is a 128-bit AES key programmed to the CRYPTOCELL peripheral through
firmware. It is retained in the AO power domain until the next reset.
To configure the KDR key, write the key value into registers HOST_IOT_KDR[0..3]. These registers are write-
only when LCS is set to DEBUG mode, and write-once when LCS is set to SECURE mode. The KDR key value
is retained when the read-back value is 1 in register HOST_IOT_KDR0 on page 222. Once configured,
CRYPTOCELL can perform cryptographic operations using the KDR key without the firmware having access
to the key value itself.

6.6.5 Direct memory access (DMA)

CRYPTOCELL implements direct memory access (DMA) for accessing memory without CPU intervention.
The following table indicates which memory is accessible through DMA.

4413_417 v1.9 218

 Peripherals

Memory type Read Write

SRAM Yes Yes
Flash No No
External flash (QSPI) No No

Table 16: DMA transaction types

Data stored in memory that is not accessible by the DMA engine must be copied to SRAM before it can be
processed by CRYPTOCELL. Maximum DMA transaction size is limited to 216-1 bytes.

6.6.6 Standards
CRYPTOCELL supports several cryptography standards.

Algorithm family Identification code Document title

TRNG NIST SP 800-90B Recommendation for the Entropy Sources Used for Random Bit Generation
AIS-31 A proposal for: Functionality classes and evaluation methodology for physical random number generators
FIPS 140-2 Security Requirements for Cryptographic Modules
PRNG NIST SP 800-90A Recommendation for Random Number Generation Using Deterministic Random Bit Generators
Stream cipher Chacha ChaCha, a variant of Salsa20, Daniel J. Bernstein, January 28th 2008
MAC Poly1305 The Poly1305-AES message-authentication code, Daniel J. Bernstein

Cryptography in NaCl, Daniel J. Bernstein

Key agreement SRP The Secure Remote Password Protocol, Thomas Wu, November 11th 1997
AES FIPS-197 Advanced Encryption Standard (AES)
NIST SP 800-38A Recommendation for Block Cipher Modes of Operation - Methods and Techniques
NIST SP 800-38B Recommendation for Block Cipher Modes of Operation: The CMAC Mode for Authentication
NIST SP 800-38C Recommendation for Block Cipher Modes of Operation: The CCM Mode for Authentication and
Confidentiality
ISO/IEC 9797-1 AES CBC-MAC per ISO/IEC 9797-1 MAC algorithm 1
IEEE 802.15.4-2011 IEEE Standard for Local and metropolitan area networks - Part 15.4: Low-Rate Wireless Personal Area
Networks (LR-WPANs), Annex B.4: Specification of generic CCM* mode of operation
Hash FIPS 180-3 Secure Hash Standard (SHA1, SHA-224, SHA-256)
RFC2104 HMAC: Keyed-Hashing for Message Authentication
RSA PKCS#1 Public-Key Cryptography Standards (PKCS) #1: RSA Cryptography Specifications v1.5/2.1
Diffie-Hellman ANSI X9.42 Public Key Cryptography for the Financial Services Industry: Agreement of Symmetric Keys Using Discrete
Logarithm Cryptography
PKCS#3 Diffie-Hellman Key-Agreement Standard
ECC ANSI X9.63 Public Key Cryptography for the Financial Services Industry - Key Agreement and Key Transport Using
Elliptic Curve Cryptography
IEEE 1363 Standard Specifications for Public-Key Cryptography
ANSI X9.62 Public Key Cryptography For The Financial Services Industry: The Elliptic Curve Digital Signature Algorithm
(ECDSA)
Ed25519 Edwards-curve, Ed25519: high-speed high-security signatures, Daniel J. Bernstein, Niels Duif, Tanja Lange,
Peter Schwabe, and Bo-Yin Yang
Curve25519 Montgomery curve, Curve25519: new Diffie-Hellman speed records, Daniel J. Bernstein
FIPS 186-4 Digital Signature Standard (DSS)
SEC 2 Recommended Elliptic Curve Domain Parameters, Certicom Research
NIST SP 800-56A rev. 2 Recommendation for Pair-Wise Key Establishment Schemes Using Discrete Logarithm Cryptography

Table 17: CRYPTOCELL cryptography standards

4413_417 v1.9 219

 Peripherals

6.6.7 Registers
Instances

Instance Base address Description

CRYPTOCELL 0x5002A000 CRYPTOCELL control interface

Register overview

Register Offset Description

ENABLE 0x500 Enable CRYPTOCELL

6.6.7.1 ENABLE
Address offset: 0x500
Enable CRYPTOCELL

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW ENABLE Enable or disable CRYPTOCELL
Disabled 0 CRYPTOCELL disabled
Enabled 1 CRYPTOCELL enabled

The CRYPTOCELL firmware API is available for initialization and control when
CRYPTOCELL is enabled

6.6.8 Host interface

This chapter describes host registers used to control CRYPTOCELL behavior.

6.6.8.1 HOST_RGF block

The HOST_RGF block contains registers for configuring LCS and device root key KDR, in addition to selecting
which cryptographic key is connected to the AES engine.

6.6.8.1.1 Registers

Instances

Instance Base address Description

CC_HOST_RGF 0x5002A000 Host platform interface

4413_417 v1.9 220

 Peripherals

Register overview

Register Offset Description

HOST_CRYPTOKEY_SEL 0x1A38 AES hardware key select
HOST_IOT_KPRTL_LOCK 0x1A4C This write-once register is the K_PRTL lock register. When this register is set, K_PRTL cannot be
used and a zeroed key will be used instead. The value of this register is saved in the CRYPTOCELL AO
power domain.
HOST_IOT_KDR0 0x1A50 This register holds bits 31:0 of K_DR. The value of this register is saved in the CRYPTOCELL AO power
domain. Reading from this address returns the K_DR valid status indicating if K_DR is successfully
retained.
HOST_IOT_KDR1 0x1A54 This register holds bits 63:32 of K_DR. The value of this register is saved in the CRYPTOCELL AO
power domain.
HOST_IOT_KDR2 0x1A58 This register holds bits 95:64 of K_DR. The value of this register is saved in the CRYPTOCELL AO
power domain.
HOST_IOT_KDR3 0x1A5C This register holds bits 127:96 of K_DR. The value of this register is saved in the CRYPTOCELL AO
power domain.
HOST_IOT_LCS 0x1A60 Controls lifecycle state (LCS) for CRYPTOCELL subsystem

6.6.8.1.1.1 HOST_CRYPTOKEY_SEL
Address offset: 0x1A38
AES hardware key select

Note: If the HOST_IOT_KPRTL_LOCK register is set, and the HOST_CRYPTOKEY_SEL register set to 1,
then the HW key that is connected to the AES engine is zero

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW HOST_CRYPTOKEY_SEL Select the source of the HW key that is used by the AES engine
K_DR 0 Use device root key K_DR from CRYPTOCELL AO power domain
K_PRTL 1 Use hard-coded RTL key K_PRTL
Session 2 Use provided session key

6.6.8.1.1.2 HOST_IOT_KPRTL_LOCK
Address offset: 0x1A4C
This write-once register is the K_PRTL lock register. When this register is set, K_PRTL cannot be used and a
zeroed key will be used instead. The value of this register is saved in the CRYPTOCELL AO power domain.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW HOST_IOT_KPRTL_LOCK This register is the K_PRTL lock register. When this register is set, K_PRTL
cannot be used and a zeroed key will be used instead. The value of this
register is saved in the CRYPTOCELL AO power domain.
Disabled 0 K_PRTL can be selected for use from register HOST_CRYPTOKEY_SEL
Enabled 1 K_PRTL has been locked until next power-on reset (POR). If K_PRTL is
selected anyway, a zeroed key will be used instead.

4413_417 v1.9 221

 Peripherals

6.6.8.1.1.3 HOST_IOT_KDR0
Address offset: 0x1A50
This register holds bits 31:0 of K_DR. The value of this register is saved in the CRYPTOCELL AO power
domain. Reading from this address returns the K_DR valid status indicating if K_DR is successfully retained.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW HOST_IOT_KDR0 Write: K_DR bits 31:0.

Read: 0x00000000 when 128-bit K_DR key value is not yet retained in the
CRYPTOCELL AO power domain.

Read: 0x00000001 when 128-bit K_DR key value is successfully retained in

the CRYPTOCELL AO power domain.

6.6.8.1.1.4 HOST_IOT_KDR1
Address offset: 0x1A54
This register holds bits 63:32 of K_DR. The value of this register is saved in the CRYPTOCELL AO power
domain.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W HOST_IOT_KDR1 K_DR bits 63:32

6.6.8.1.1.5 HOST_IOT_KDR2
Address offset: 0x1A58
This register holds bits 95:64 of K_DR. The value of this register is saved in the CRYPTOCELL AO power
domain.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W HOST_IOT_KDR2 K_DR bits 95:64

6.6.8.1.1.6 HOST_IOT_KDR3
Address offset: 0x1A5C
This register holds bits 127:96 of K_DR. The value of this register is saved in the CRYPTOCELL AO power
domain.

4413_417 v1.9 222

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W HOST_IOT_KDR3 K_DR bits 127:96

6.6.8.1.1.7 HOST_IOT_LCS
Address offset: 0x1A60
Controls lifecycle state (LCS) for CRYPTOCELL subsystem

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B A A A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
A RW LCS Lifecycle state value. This field is write-once per reset.
Debug 0 CC310 operates in debug mode
Secure 2 CC310 operates in secure mode
B RW LCS_IS_VALID Read-only field. Indicates if CRYPTOCELL LCS has been successfully
configured since last reset.
Invalid 0 Valid LCS not yet retained in the CRYPTOCELL AO power domain
Valid 1 Valid LCS successfully retained in the CRYPTOCELL AO power domain

6.7 ECB — AES electronic codebook mode encryption

The AES electronic codebook mode encryption (ECB) can be used for a range of cryptographic functions
like hash generation, digital signatures, and keystream generation for data encryption/decryption. The ECB
encryption block supports 128 bit AES encryption (encryption only, not decryption).
AES ECB operates with EasyDMA access to system Data RAM for in-place operations on cleartext
and ciphertext during encryption. ECB uses the same AES core as the CCM and AAR blocks, and is an
asynchronous operation which may not complete if the AES core is busy.
AES ECB features:
• 128 bit AES encryption
• Supports standard AES ECB block encryption
• Memory pointer support
• DMA data transfer
AES ECB performs a 128 bit AES block encrypt. At the STARTECB task, data and key is loaded into the
algorithm by EasyDMA. When output data has been written back to memory, the ENDECB event is
triggered.
AES ECB can be stopped by triggering the STOPECB task.

6.7.1 Shared resources

The ECB, CCM, and AAR share the same AES module. The ECB will always have lowest priority, and if there
is a sharing conflict during encryption, the ECB operation will be aborted and an ERRORECB event will be
generated.

4413_417 v1.9 223

 Peripherals

6.7.2 EasyDMA
The ECB implements an EasyDMA mechanism for reading and writing to the Data RAM. This DMA cannot
access the program memory or any other parts of the memory area except RAM.
If the ECBDATAPTR is not pointing to the Data RAM region, an EasyDMA transfer may result in a HardFault
or RAM corruption. See Memory on page 21 for more information about the different memory regions.
The EasyDMA will have finished accessing the Data RAM when the ENDECB or ERRORECB is generated.

6.7.3 ECB data structure

Block encrypt input and output is stored in the same data structure. ECBDATAPTR should point to this data
structure before STARTECB is initiated.

Property Address offset Description

KEY 0 16 byte AES key
CLEARTEXT 16 16 byte AES cleartext input block
CIPHERTEXT 32 16 byte AES ciphertext output block

Table 18: ECB data structure overview

6.7.4 Registers
Instances

Instance Base address Description

ECB 0x4000E000 AES electronic code book (ECB) mode block encryption

Register overview

Register Offset Description

TASKS_STARTECB 0x000 Start ECB block encrypt
TASKS_STOPECB 0x004 Abort a possible executing ECB operation
EVENTS_ENDECB 0x100 ECB block encrypt complete
EVENTS_ERRORECB 0x104 ECB block encrypt aborted because of a STOPECB task or due to an error
INTENSET 0x304 Enable interrupt
INTENCLR 0x308 Disable interrupt
ECBDATAPTR 0x504 ECB block encrypt memory pointers

6.7.4.1 TASKS_STARTECB
Address offset: 0x000
Start ECB block encrypt
If a crypto operation is already running in the AES core, the STARTECB task will not start a new encryption
and an ERRORECB event will be triggered.

4413_417 v1.9 224

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STARTECB Start ECB block encrypt

If a crypto operation is already running in the AES core, the STARTECB task
will not start a new encryption and an ERRORECB event will be triggered.
Trigger 1 Trigger task

6.7.4.2 TASKS_STOPECB
Address offset: 0x004
Abort a possible executing ECB operation
If a running ECB operation is aborted by STOPECB, the ERRORECB event is triggered.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STOPECB Abort a possible executing ECB operation

If a running ECB operation is aborted by STOPECB, the ERRORECB event is

triggered.
Trigger 1 Trigger task

6.7.4.3 EVENTS_ENDECB
Address offset: 0x100
ECB block encrypt complete

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_ENDECB ECB block encrypt complete
NotGenerated 0 Event not generated
Generated 1 Event generated

6.7.4.4 EVENTS_ERRORECB
Address offset: 0x104
ECB block encrypt aborted because of a STOPECB task or due to an error

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_ERRORECB ECB block encrypt aborted because of a STOPECB task or due to an error
NotGenerated 0 Event not generated
Generated 1 Event generated

4413_417 v1.9 225

 Peripherals

6.7.4.5 INTENSET
Address offset: 0x304
Enable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW ENDECB Write '1' to enable interrupt for event ENDECB
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW ERRORECB Write '1' to enable interrupt for event ERRORECB
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.7.4.6 INTENCLR
Address offset: 0x308
Disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW ENDECB Write '1' to disable interrupt for event ENDECB
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW ERRORECB Write '1' to disable interrupt for event ERRORECB
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.7.4.7 ECBDATAPTR
Address offset: 0x504
ECB block encrypt memory pointers

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW ECBDATAPTR Pointer to the ECB data structure (see Table 1 ECB data structure overview)

4413_417 v1.9 226

 Peripherals

6.7.5 Electrical specification

6.7.5.1 ECB Electrical Specification

Symbol Description Min. Typ. Max. Units

tECB Run time per 16 byte block in all modes 7.2 µs

6.8 EGU — Event generator unit

Event generator unit (EGU) provides support for interlayer signaling. This means providing support for
atomic triggering of both CPU execution and hardware tasks, from both firmware (by CPU) and hardware
(by PPI). This feature can be used for triggering CPU execution at a lower priority execution from a higher
priority execution, or to handle a peripheral's interrupt service routine (ISR) execution at a lower priority
for some of its events. However, triggering any priority from any priority is possible.
Listed here are the main EGU features:
• Software-enabled interrupt triggering
• Separate interrupt vectors for every EGU instance
• Up to 16 separate event flags per interrupt for multiplexing
EGU implements a set of tasks which can individually be triggered to generate the corresponding event.
For example, the corresponding event for TASKS_TRIGGER[n] is EVENTS_TRIGGERED[n].

6.8.1 Registers
Instances

Instance Base address Description

EGU0 0x40014000 Event generator unit 0
EGU1 0x40015000 Event generator unit 1
EGU2 0x40016000 Event generator unit 2
EGU3 0x40017000 Event generator unit 3
EGU4 0x40018000 Event generator unit 4
EGU5 0x40019000 Event generator unit 5

Register overview

Register Offset Description

TASKS_TRIGGER[0] 0x000 Trigger 0 for triggering the corresponding TRIGGERED[0] event
TASKS_TRIGGER[1] 0x004 Trigger 1 for triggering the corresponding TRIGGERED[1] event
TASKS_TRIGGER[2] 0x008 Trigger 2 for triggering the corresponding TRIGGERED[2] event
TASKS_TRIGGER[3] 0x00C Trigger 3 for triggering the corresponding TRIGGERED[3] event
TASKS_TRIGGER[4] 0x010 Trigger 4 for triggering the corresponding TRIGGERED[4] event
TASKS_TRIGGER[5] 0x014 Trigger 5 for triggering the corresponding TRIGGERED[5] event
TASKS_TRIGGER[6] 0x018 Trigger 6 for triggering the corresponding TRIGGERED[6] event
TASKS_TRIGGER[7] 0x01C Trigger 7 for triggering the corresponding TRIGGERED[7] event
TASKS_TRIGGER[8] 0x020 Trigger 8 for triggering the corresponding TRIGGERED[8] event
TASKS_TRIGGER[9] 0x024 Trigger 9 for triggering the corresponding TRIGGERED[9] event
TASKS_TRIGGER[10] 0x028 Trigger 10 for triggering the corresponding TRIGGERED[10] event
TASKS_TRIGGER[11] 0x02C Trigger 11 for triggering the corresponding TRIGGERED[11] event

4413_417 v1.9 227

 Peripherals

Register Offset Description

TASKS_TRIGGER[12] 0x030 Trigger 12 for triggering the corresponding TRIGGERED[12] event
TASKS_TRIGGER[13] 0x034 Trigger 13 for triggering the corresponding TRIGGERED[13] event
TASKS_TRIGGER[14] 0x038 Trigger 14 for triggering the corresponding TRIGGERED[14] event
TASKS_TRIGGER[15] 0x03C Trigger 15 for triggering the corresponding TRIGGERED[15] event
EVENTS_TRIGGERED[0] 0x100 Event number 0 generated by triggering the corresponding TRIGGER[0] task
EVENTS_TRIGGERED[1] 0x104 Event number 1 generated by triggering the corresponding TRIGGER[1] task
EVENTS_TRIGGERED[2] 0x108 Event number 2 generated by triggering the corresponding TRIGGER[2] task
EVENTS_TRIGGERED[3] 0x10C Event number 3 generated by triggering the corresponding TRIGGER[3] task
EVENTS_TRIGGERED[4] 0x110 Event number 4 generated by triggering the corresponding TRIGGER[4] task
EVENTS_TRIGGERED[5] 0x114 Event number 5 generated by triggering the corresponding TRIGGER[5] task
EVENTS_TRIGGERED[6] 0x118 Event number 6 generated by triggering the corresponding TRIGGER[6] task
EVENTS_TRIGGERED[7] 0x11C Event number 7 generated by triggering the corresponding TRIGGER[7] task
EVENTS_TRIGGERED[8] 0x120 Event number 8 generated by triggering the corresponding TRIGGER[8] task
EVENTS_TRIGGERED[9] 0x124 Event number 9 generated by triggering the corresponding TRIGGER[9] task
EVENTS_TRIGGERED[10] 0x128 Event number 10 generated by triggering the corresponding TRIGGER[10] task
EVENTS_TRIGGERED[11] 0x12C Event number 11 generated by triggering the corresponding TRIGGER[11] task
EVENTS_TRIGGERED[12] 0x130 Event number 12 generated by triggering the corresponding TRIGGER[12] task
EVENTS_TRIGGERED[13] 0x134 Event number 13 generated by triggering the corresponding TRIGGER[13] task
EVENTS_TRIGGERED[14] 0x138 Event number 14 generated by triggering the corresponding TRIGGER[14] task
EVENTS_TRIGGERED[15] 0x13C Event number 15 generated by triggering the corresponding TRIGGER[15] task
INTEN 0x300 Enable or disable interrupt
INTENSET 0x304 Enable interrupt
INTENCLR 0x308 Disable interrupt

6.8.1.1 TASKS_TRIGGER[0]
Address offset: 0x000
Trigger 0 for triggering the corresponding TRIGGERED[0] event

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_TRIGGER Trigger 0 for triggering the corresponding TRIGGERED[0] event
Trigger 1 Trigger task

6.8.1.2 TASKS_TRIGGER[1]
Address offset: 0x004
Trigger 1 for triggering the corresponding TRIGGERED[1] event

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_TRIGGER Trigger 1 for triggering the corresponding TRIGGERED[1] event
Trigger 1 Trigger task

6.8.1.3 TASKS_TRIGGER[2]
Address offset: 0x008
Trigger 2 for triggering the corresponding TRIGGERED[2] event

4413_417 v1.9 228

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_TRIGGER Trigger 2 for triggering the corresponding TRIGGERED[2] event
Trigger 1 Trigger task

6.8.1.4 TASKS_TRIGGER[3]
Address offset: 0x00C
Trigger 3 for triggering the corresponding TRIGGERED[3] event

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_TRIGGER Trigger 3 for triggering the corresponding TRIGGERED[3] event
Trigger 1 Trigger task

6.8.1.5 TASKS_TRIGGER[4]
Address offset: 0x010
Trigger 4 for triggering the corresponding TRIGGERED[4] event

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_TRIGGER Trigger 4 for triggering the corresponding TRIGGERED[4] event
Trigger 1 Trigger task

6.8.1.6 TASKS_TRIGGER[5]
Address offset: 0x014
Trigger 5 for triggering the corresponding TRIGGERED[5] event

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_TRIGGER Trigger 5 for triggering the corresponding TRIGGERED[5] event
Trigger 1 Trigger task

6.8.1.7 TASKS_TRIGGER[6]
Address offset: 0x018
Trigger 6 for triggering the corresponding TRIGGERED[6] event

4413_417 v1.9 229

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_TRIGGER Trigger 6 for triggering the corresponding TRIGGERED[6] event
Trigger 1 Trigger task

6.8.1.8 TASKS_TRIGGER[7]
Address offset: 0x01C
Trigger 7 for triggering the corresponding TRIGGERED[7] event

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_TRIGGER Trigger 7 for triggering the corresponding TRIGGERED[7] event
Trigger 1 Trigger task

6.8.1.9 TASKS_TRIGGER[8]
Address offset: 0x020
Trigger 8 for triggering the corresponding TRIGGERED[8] event

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_TRIGGER Trigger 8 for triggering the corresponding TRIGGERED[8] event
Trigger 1 Trigger task

6.8.1.10 TASKS_TRIGGER[9]
Address offset: 0x024
Trigger 9 for triggering the corresponding TRIGGERED[9] event

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_TRIGGER Trigger 9 for triggering the corresponding TRIGGERED[9] event
Trigger 1 Trigger task

6.8.1.11 TASKS_TRIGGER[10]
Address offset: 0x028
Trigger 10 for triggering the corresponding TRIGGERED[10] event

4413_417 v1.9 230

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_TRIGGER Trigger 10 for triggering the corresponding TRIGGERED[10] event
Trigger 1 Trigger task

6.8.1.12 TASKS_TRIGGER[11]
Address offset: 0x02C
Trigger 11 for triggering the corresponding TRIGGERED[11] event

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_TRIGGER Trigger 11 for triggering the corresponding TRIGGERED[11] event
Trigger 1 Trigger task

6.8.1.13 TASKS_TRIGGER[12]
Address offset: 0x030
Trigger 12 for triggering the corresponding TRIGGERED[12] event

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_TRIGGER Trigger 12 for triggering the corresponding TRIGGERED[12] event
Trigger 1 Trigger task

6.8.1.14 TASKS_TRIGGER[13]
Address offset: 0x034
Trigger 13 for triggering the corresponding TRIGGERED[13] event

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_TRIGGER Trigger 13 for triggering the corresponding TRIGGERED[13] event
Trigger 1 Trigger task

6.8.1.15 TASKS_TRIGGER[14]
Address offset: 0x038
Trigger 14 for triggering the corresponding TRIGGERED[14] event

4413_417 v1.9 231

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_TRIGGER Trigger 14 for triggering the corresponding TRIGGERED[14] event
Trigger 1 Trigger task

6.8.1.16 TASKS_TRIGGER[15]
Address offset: 0x03C
Trigger 15 for triggering the corresponding TRIGGERED[15] event

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_TRIGGER Trigger 15 for triggering the corresponding TRIGGERED[15] event
Trigger 1 Trigger task

6.8.1.17 EVENTS_TRIGGERED[0]
Address offset: 0x100
Event number 0 generated by triggering the corresponding TRIGGER[0] task

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_TRIGGERED Event number 0 generated by triggering the corresponding TRIGGER[0] task
NotGenerated 0 Event not generated
Generated 1 Event generated

6.8.1.18 EVENTS_TRIGGERED[1]
Address offset: 0x104
Event number 1 generated by triggering the corresponding TRIGGER[1] task

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_TRIGGERED Event number 1 generated by triggering the corresponding TRIGGER[1] task
NotGenerated 0 Event not generated
Generated 1 Event generated

6.8.1.19 EVENTS_TRIGGERED[2]
Address offset: 0x108
Event number 2 generated by triggering the corresponding TRIGGER[2] task

4413_417 v1.9 232

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_TRIGGERED Event number 2 generated by triggering the corresponding TRIGGER[2] task
NotGenerated 0 Event not generated
Generated 1 Event generated

6.8.1.20 EVENTS_TRIGGERED[3]
Address offset: 0x10C
Event number 3 generated by triggering the corresponding TRIGGER[3] task

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_TRIGGERED Event number 3 generated by triggering the corresponding TRIGGER[3] task
NotGenerated 0 Event not generated
Generated 1 Event generated

6.8.1.21 EVENTS_TRIGGERED[4]
Address offset: 0x110
Event number 4 generated by triggering the corresponding TRIGGER[4] task

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_TRIGGERED Event number 4 generated by triggering the corresponding TRIGGER[4] task
NotGenerated 0 Event not generated
Generated 1 Event generated

6.8.1.22 EVENTS_TRIGGERED[5]
Address offset: 0x114
Event number 5 generated by triggering the corresponding TRIGGER[5] task

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_TRIGGERED Event number 5 generated by triggering the corresponding TRIGGER[5] task
NotGenerated 0 Event not generated
Generated 1 Event generated

6.8.1.23 EVENTS_TRIGGERED[6]
Address offset: 0x118
Event number 6 generated by triggering the corresponding TRIGGER[6] task

4413_417 v1.9 233

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_TRIGGERED Event number 6 generated by triggering the corresponding TRIGGER[6] task
NotGenerated 0 Event not generated
Generated 1 Event generated

6.8.1.24 EVENTS_TRIGGERED[7]
Address offset: 0x11C
Event number 7 generated by triggering the corresponding TRIGGER[7] task

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_TRIGGERED Event number 7 generated by triggering the corresponding TRIGGER[7] task
NotGenerated 0 Event not generated
Generated 1 Event generated

6.8.1.25 EVENTS_TRIGGERED[8]
Address offset: 0x120
Event number 8 generated by triggering the corresponding TRIGGER[8] task

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_TRIGGERED Event number 8 generated by triggering the corresponding TRIGGER[8] task
NotGenerated 0 Event not generated
Generated 1 Event generated

6.8.1.26 EVENTS_TRIGGERED[9]
Address offset: 0x124
Event number 9 generated by triggering the corresponding TRIGGER[9] task

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_TRIGGERED Event number 9 generated by triggering the corresponding TRIGGER[9] task
NotGenerated 0 Event not generated
Generated 1 Event generated

6.8.1.27 EVENTS_TRIGGERED[10]
Address offset: 0x128
Event number 10 generated by triggering the corresponding TRIGGER[10] task

4413_417 v1.9 234

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_TRIGGERED Event number 10 generated by triggering the corresponding TRIGGER[10]
task
NotGenerated 0 Event not generated
Generated 1 Event generated

6.8.1.28 EVENTS_TRIGGERED[11]
Address offset: 0x12C
Event number 11 generated by triggering the corresponding TRIGGER[11] task

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_TRIGGERED Event number 11 generated by triggering the corresponding TRIGGER[11]
task
NotGenerated 0 Event not generated
Generated 1 Event generated

6.8.1.29 EVENTS_TRIGGERED[12]
Address offset: 0x130
Event number 12 generated by triggering the corresponding TRIGGER[12] task

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_TRIGGERED Event number 12 generated by triggering the corresponding TRIGGER[12]
task
NotGenerated 0 Event not generated
Generated 1 Event generated

6.8.1.30 EVENTS_TRIGGERED[13]
Address offset: 0x134
Event number 13 generated by triggering the corresponding TRIGGER[13] task

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_TRIGGERED Event number 13 generated by triggering the corresponding TRIGGER[13]
task
NotGenerated 0 Event not generated
Generated 1 Event generated

4413_417 v1.9 235

 Peripherals

6.8.1.31 EVENTS_TRIGGERED[14]
Address offset: 0x138
Event number 14 generated by triggering the corresponding TRIGGER[14] task

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_TRIGGERED Event number 14 generated by triggering the corresponding TRIGGER[14]
task
NotGenerated 0 Event not generated
Generated 1 Event generated

6.8.1.32 EVENTS_TRIGGERED[15]
Address offset: 0x13C
Event number 15 generated by triggering the corresponding TRIGGER[15] task

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_TRIGGERED Event number 15 generated by triggering the corresponding TRIGGER[15]
task
NotGenerated 0 Event not generated
Generated 1 Event generated

6.8.1.33 INTEN
Address offset: 0x300
Enable or disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TRIGGERED[0] Enable or disable interrupt for event TRIGGERED[0]
Disabled 0 Disable
Enabled 1 Enable
B RW TRIGGERED[1] Enable or disable interrupt for event TRIGGERED[1]
Disabled 0 Disable
Enabled 1 Enable
C RW TRIGGERED[2] Enable or disable interrupt for event TRIGGERED[2]
Disabled 0 Disable
Enabled 1 Enable
D RW TRIGGERED[3] Enable or disable interrupt for event TRIGGERED[3]
Disabled 0 Disable
Enabled 1 Enable
E RW TRIGGERED[4] Enable or disable interrupt for event TRIGGERED[4]
Disabled 0 Disable
Enabled 1 Enable

4413_417 v1.9 236

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
F RW TRIGGERED[5] Enable or disable interrupt for event TRIGGERED[5]
Disabled 0 Disable
Enabled 1 Enable
G RW TRIGGERED[6] Enable or disable interrupt for event TRIGGERED[6]
Disabled 0 Disable
Enabled 1 Enable
H RW TRIGGERED[7] Enable or disable interrupt for event TRIGGERED[7]
Disabled 0 Disable
Enabled 1 Enable
I RW TRIGGERED[8] Enable or disable interrupt for event TRIGGERED[8]
Disabled 0 Disable
Enabled 1 Enable
J RW TRIGGERED[9] Enable or disable interrupt for event TRIGGERED[9]
Disabled 0 Disable
Enabled 1 Enable
K RW TRIGGERED[10] Enable or disable interrupt for event TRIGGERED[10]
Disabled 0 Disable
Enabled 1 Enable
L RW TRIGGERED[11] Enable or disable interrupt for event TRIGGERED[11]
Disabled 0 Disable
Enabled 1 Enable
M RW TRIGGERED[12] Enable or disable interrupt for event TRIGGERED[12]
Disabled 0 Disable
Enabled 1 Enable
N RW TRIGGERED[13] Enable or disable interrupt for event TRIGGERED[13]
Disabled 0 Disable
Enabled 1 Enable
O RW TRIGGERED[14] Enable or disable interrupt for event TRIGGERED[14]
Disabled 0 Disable
Enabled 1 Enable
P RW TRIGGERED[15] Enable or disable interrupt for event TRIGGERED[15]
Disabled 0 Disable
Enabled 1 Enable

6.8.1.34 INTENSET
Address offset: 0x304
Enable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TRIGGERED[0] Write '1' to enable interrupt for event TRIGGERED[0]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW TRIGGERED[1] Write '1' to enable interrupt for event TRIGGERED[1]
Set 1 Enable

4413_417 v1.9 237

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW TRIGGERED[2] Write '1' to enable interrupt for event TRIGGERED[2]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
D RW TRIGGERED[3] Write '1' to enable interrupt for event TRIGGERED[3]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
E RW TRIGGERED[4] Write '1' to enable interrupt for event TRIGGERED[4]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
F RW TRIGGERED[5] Write '1' to enable interrupt for event TRIGGERED[5]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
G RW TRIGGERED[6] Write '1' to enable interrupt for event TRIGGERED[6]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
H RW TRIGGERED[7] Write '1' to enable interrupt for event TRIGGERED[7]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
I RW TRIGGERED[8] Write '1' to enable interrupt for event TRIGGERED[8]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
J RW TRIGGERED[9] Write '1' to enable interrupt for event TRIGGERED[9]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
K RW TRIGGERED[10] Write '1' to enable interrupt for event TRIGGERED[10]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
L RW TRIGGERED[11] Write '1' to enable interrupt for event TRIGGERED[11]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
M RW TRIGGERED[12] Write '1' to enable interrupt for event TRIGGERED[12]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
N RW TRIGGERED[13] Write '1' to enable interrupt for event TRIGGERED[13]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

4413_417 v1.9 238

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
O RW TRIGGERED[14] Write '1' to enable interrupt for event TRIGGERED[14]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
P RW TRIGGERED[15] Write '1' to enable interrupt for event TRIGGERED[15]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.8.1.35 INTENCLR
Address offset: 0x308
Disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TRIGGERED[0] Write '1' to disable interrupt for event TRIGGERED[0]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW TRIGGERED[1] Write '1' to disable interrupt for event TRIGGERED[1]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW TRIGGERED[2] Write '1' to disable interrupt for event TRIGGERED[2]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
D RW TRIGGERED[3] Write '1' to disable interrupt for event TRIGGERED[3]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
E RW TRIGGERED[4] Write '1' to disable interrupt for event TRIGGERED[4]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
F RW TRIGGERED[5] Write '1' to disable interrupt for event TRIGGERED[5]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
G RW TRIGGERED[6] Write '1' to disable interrupt for event TRIGGERED[6]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
H RW TRIGGERED[7] Write '1' to disable interrupt for event TRIGGERED[7]
Clear 1 Disable
Disabled 0 Read: Disabled

4413_417 v1.9 239

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Enabled 1 Read: Enabled
I RW TRIGGERED[8] Write '1' to disable interrupt for event TRIGGERED[8]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
J RW TRIGGERED[9] Write '1' to disable interrupt for event TRIGGERED[9]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
K RW TRIGGERED[10] Write '1' to disable interrupt for event TRIGGERED[10]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
L RW TRIGGERED[11] Write '1' to disable interrupt for event TRIGGERED[11]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
M RW TRIGGERED[12] Write '1' to disable interrupt for event TRIGGERED[12]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
N RW TRIGGERED[13] Write '1' to disable interrupt for event TRIGGERED[13]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
O RW TRIGGERED[14] Write '1' to disable interrupt for event TRIGGERED[14]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
P RW TRIGGERED[15] Write '1' to disable interrupt for event TRIGGERED[15]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.8.2 Electrical specification

6.8.2.1 EGU Electrical Specification

Symbol Description Min. Typ. Max. Units

tEGU,EVT Latency between setting an EGU event flag and the system setting an 1 cycles
interrupt

6.9 GPIO — General purpose input/output

The general purpose input/output pins (GPIOs) are grouped as one or more ports, with each port having
up to 32 GPIOs.

4413_417 v1.9 240

 Peripherals

The number of ports and GPIOs per port varies with product variant and package. Refer to Registers on
page 243 and Pin assignments on page 845 for more information about the number of GPIOs that are
supported.
GPIO has the following user-configurable features:
• Up to 32 GPIO pins per GPIO port
• Output drive strength
• Internal pull-up and pull-down resistors
• Wake-up from high or low level triggers on all pins
• Trigger interrupt on state changes on any pin
• All pins can be used by the PPI task/event system
• One or more GPIO outputs can be controlled through the PPI and GPIOTE channels
• Any pin can be mapped to a peripheral for layout flexibility
• GPIO state changes captured on the SENSE signal can be stored by the LATCH register
The GPIO port peripheral implements up to 32 pins, PIN0 through PIN31. Each of these pins can be
individually configured in the PIN_CNF[n] registers (n=0..31).
The following parameters can be configured through these registers:
• Direction
• Drive strength
• Enabling of pull-up and pull-down resistors
• Pin sensing
• Input buffer disconnect
• Analog input (for selected pins)
The PIN_CNF registers are retained registers. See POWER — Power supply on page 80 for more
information about retained registers.

6.9.1 Pin configuration

Pins can be individually configured through the SENSE field in the PIN_CNF[n] register to detect either a
high or low level input.
When the correct level is detected on a configured pin, the sense mechanism will set the DETECT signal
high. Each pin has a separate DETECT signal. Default behavior, defined by the DETECTMODE register,
combines all DETECT signals from the pins in the GPIO port into one common DETECT signal and routes it
through the system to be utilized by other peripherals. This mechanism is functional in both System ON
and System OFF mode. See GPIO port and the GPIO pin details on page 242.
The following figure illustrates the GPIO port containing 32 individual pins, where PIN0 is shown in more
detail for reference. All signals on the left side of the illustration are used by other peripherals in the
system and therefore not directly available to the CPU.

4413_417 v1.9 241

 Peripherals

LDETECT

PIN0
ANAEN
GPIO port
DIR_OVERRIDE
DETECTMODE PIN[0].CNF.DRIVE
OUT_OVERRIDE
PIN0 PIN0
DETECT LATCH OUT
PIN[0].OUT
O
PIN[0].IN
PIN[0].OUT PIN[0].CNF
PIN[0].CNF.DIR

PIN0.DETECT
Sense
PIN1.DETECT ..
PIN[0].CNF.SENSE PIN[0].CNF.PULL

PIN[0].CNF.INPUT
PIN31.DETECT
PIN[0].IN I
PIN31 PIN31
IN PIN[31].OUT
PIN[31].IN
PIN[31].CNF
INPUT_OVERRIDE

ANAIN

O: output buffer I: input buffer

Figure 45: GPIO port and the GPIO pin details

Pins should be in a level that cannot trigger the sense mechanism before being enabled. If the SENSE
condition configured in the PIN_CNF registers is met when the sense mechanism is enabled, the DETECT
signal will immediately go high. A PORT event is triggered if the DETECT signal was low before enabling the
sense mechanism. See GPIOTE — GPIO tasks and events on page 290.
See the following peripherals for more information about how the DETECT signal is used:
• POWER — Power supply on page 80 - uses the DETECT signal to exit from System OFF mode.
• GPIOTE — GPIO tasks and events on page 290 - uses the DETECT signal to generate the PORT event.
When a pin's PINx.DETECT signal goes high, a flag is set in the LATCH register. For example, when the
PIN0.DETECT signal goes high, bit 0 in the LATCH register is set to 1. If the CPU performs a clear operation
on a bit in the LATCH register when the associated PINx.DETECT signal is high, the bit in the LATCH register
will not be cleared. The LATCH register will only be cleared if the CPU explicitly clears it by writing a 1 to
the bit that shall be cleared, i.e. the LATCH register will not be affected by a PINx.DETECT signal being set
low.
The LDETECT signal will be set high when one or more bits in the LATCH register are 1. The LDETECT signal
will be set low when all bits in the LATCH register are successfully cleared to 0.
If one or more bits in the LATCH register are 1 after the CPU has performed a clear operation on the LATCH
register, a rising edge will be generated on the LDETECT signal. This is illustrated in DETECT signal behavior
on page 243.

Note: The CPU can read the LATCH register at any time to check if a SENSE condition has been
met on any of the GPIO pins. This is still valid if that condition is no longer met at the time the CPU
queries the LATCH register. This mechanism will work even if the LDETECT signal is not used as the
DETECT signal.

The LDETECT signal is by default not connected to the GPIO port's DETECT signal, but via the DETECTMODE
register. It is possible to change from default behavior to the DETECT signal that is derived directly from
the LDETECT signal. See GPIO port and the GPIO pin details on page 242. The following figure illustrates
the DETECT signal behavior for these two alternatives.

4413_417 v1.9 242

 Peripherals

PIN31.DETECT

PIN1.DETECT

PIN0.DETECT

DETECT
(Default mode)

LATCH.31

LATCH.1

LATCH.0

DETECT
(LDETECT mode)
CPU

1 2 3 4

LATCH = (1 << 31)

LATCH = (1<<0)

LATCH = (1<<1)

LATCH = (1<<1)
Figure 46: DETECT signal behavior

A GPIO pin input buffer can be disconnected from the pin to enable power savings when the pin is not
used as an input, see GPIO port and the GPIO pin details on page 242. Input buffers must be connected
to get a valid input value in the IN register, and for the sense mechanism to get access to the pin.
Other peripherals in the system can connect to GPIO pins and override their output value and
configuration, or read their analog or digital input value. See GPIO port and the GPIO pin details on page
242.
Selected pins also support analog input signals, see ANAIN in GPIO port and the GPIO pin details on page
242. The assignment of the analog pins can be found in Pin assignments on page 845.

Note: When a pin is configured as digital input, increased current consumption occurs when the
input voltage is between VIL and VIH. It is good practice to ensure that the external circuitry does
not drive that pin to levels between VIL and VIH for a long period of time.

6.9.2 Registers
Instances

Instance Base address Description

GPIO 0x50000000 General purpose input and output

This instance is deprecated.

P0 0x50000000 General purpose input and output, port 0
P1 0x50000300 General purpose input and output, port 1

4413_417 v1.9 243

 Peripherals

Configuration

Instance Configuration
GPIO
P0 P0.00 to P0.31 implemented
P1 P1.00 to P1.15 implemented

Register overview

Register Offset Description

OUT 0x504 Write GPIO port
OUTSET 0x508 Set individual bits in GPIO port
OUTCLR 0x50C Clear individual bits in GPIO port
IN 0x510 Read GPIO port
DIR 0x514 Direction of GPIO pins
DIRSET 0x518 DIR set register
DIRCLR 0x51C DIR clear register
LATCH 0x520 Latch register indicating what GPIO pins that have met the criteria set in the PIN_CNF[n].SENSE
registers
DETECTMODE 0x524 Select between default DETECT signal behavior and LDETECT mode
PIN_CNF[0] 0x700 Configuration of GPIO pins
PIN_CNF[1] 0x704 Configuration of GPIO pins
PIN_CNF[2] 0x708 Configuration of GPIO pins
PIN_CNF[3] 0x70C Configuration of GPIO pins
PIN_CNF[4] 0x710 Configuration of GPIO pins
PIN_CNF[5] 0x714 Configuration of GPIO pins
PIN_CNF[6] 0x718 Configuration of GPIO pins
PIN_CNF[7] 0x71C Configuration of GPIO pins
PIN_CNF[8] 0x720 Configuration of GPIO pins
PIN_CNF[9] 0x724 Configuration of GPIO pins
PIN_CNF[10] 0x728 Configuration of GPIO pins
PIN_CNF[11] 0x72C Configuration of GPIO pins
PIN_CNF[12] 0x730 Configuration of GPIO pins
PIN_CNF[13] 0x734 Configuration of GPIO pins
PIN_CNF[14] 0x738 Configuration of GPIO pins
PIN_CNF[15] 0x73C Configuration of GPIO pins
PIN_CNF[16] 0x740 Configuration of GPIO pins
PIN_CNF[17] 0x744 Configuration of GPIO pins
PIN_CNF[18] 0x748 Configuration of GPIO pins
PIN_CNF[19] 0x74C Configuration of GPIO pins
PIN_CNF[20] 0x750 Configuration of GPIO pins
PIN_CNF[21] 0x754 Configuration of GPIO pins
PIN_CNF[22] 0x758 Configuration of GPIO pins
PIN_CNF[23] 0x75C Configuration of GPIO pins
PIN_CNF[24] 0x760 Configuration of GPIO pins
PIN_CNF[25] 0x764 Configuration of GPIO pins
PIN_CNF[26] 0x768 Configuration of GPIO pins
PIN_CNF[27] 0x76C Configuration of GPIO pins
PIN_CNF[28] 0x770 Configuration of GPIO pins
PIN_CNF[29] 0x774 Configuration of GPIO pins
PIN_CNF[30] 0x778 Configuration of GPIO pins
PIN_CNF[31] 0x77C Configuration of GPIO pins

4413_417 v1.9 244

 Peripherals

6.9.2.1 OUT
Address offset: 0x504
Write GPIO port

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PIN0 Pin 0
Low 0 Pin driver is low
High 1 Pin driver is high
B RW PIN1 Pin 1
Low 0 Pin driver is low
High 1 Pin driver is high
C RW PIN2 Pin 2
Low 0 Pin driver is low
High 1 Pin driver is high
D RW PIN3 Pin 3
Low 0 Pin driver is low
High 1 Pin driver is high
E RW PIN4 Pin 4
Low 0 Pin driver is low
High 1 Pin driver is high
F RW PIN5 Pin 5
Low 0 Pin driver is low
High 1 Pin driver is high
G RW PIN6 Pin 6
Low 0 Pin driver is low
High 1 Pin driver is high
H RW PIN7 Pin 7
Low 0 Pin driver is low
High 1 Pin driver is high
I RW PIN8 Pin 8
Low 0 Pin driver is low
High 1 Pin driver is high
J RW PIN9 Pin 9
Low 0 Pin driver is low
High 1 Pin driver is high
K RW PIN10 Pin 10
Low 0 Pin driver is low
High 1 Pin driver is high
L RW PIN11 Pin 11
Low 0 Pin driver is low
High 1 Pin driver is high
M RW PIN12 Pin 12
Low 0 Pin driver is low
High 1 Pin driver is high
N RW PIN13 Pin 13
Low 0 Pin driver is low
High 1 Pin driver is high
O RW PIN14 Pin 14
Low 0 Pin driver is low

4413_417 v1.9 245

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
High 1 Pin driver is high
P RW PIN15 Pin 15
Low 0 Pin driver is low
High 1 Pin driver is high
Q RW PIN16 Pin 16
Low 0 Pin driver is low
High 1 Pin driver is high
R RW PIN17 Pin 17
Low 0 Pin driver is low
High 1 Pin driver is high
S RW PIN18 Pin 18
Low 0 Pin driver is low
High 1 Pin driver is high
T RW PIN19 Pin 19
Low 0 Pin driver is low
High 1 Pin driver is high
U RW PIN20 Pin 20
Low 0 Pin driver is low
High 1 Pin driver is high
V RW PIN21 Pin 21
Low 0 Pin driver is low
High 1 Pin driver is high
W RW PIN22 Pin 22
Low 0 Pin driver is low
High 1 Pin driver is high
X RW PIN23 Pin 23
Low 0 Pin driver is low
High 1 Pin driver is high
Y RW PIN24 Pin 24
Low 0 Pin driver is low
High 1 Pin driver is high
Z RW PIN25 Pin 25
Low 0 Pin driver is low
High 1 Pin driver is high
a RW PIN26 Pin 26
Low 0 Pin driver is low
High 1 Pin driver is high
b RW PIN27 Pin 27
Low 0 Pin driver is low
High 1 Pin driver is high
c RW PIN28 Pin 28
Low 0 Pin driver is low
High 1 Pin driver is high
d RW PIN29 Pin 29
Low 0 Pin driver is low
High 1 Pin driver is high
e RW PIN30 Pin 30
Low 0 Pin driver is low
High 1 Pin driver is high
f RW PIN31 Pin 31

4413_417 v1.9 246

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Low 0 Pin driver is low
High 1 Pin driver is high

6.9.2.2 OUTSET
Address offset: 0x508
Set individual bits in GPIO port

Note: Read: reads value of OUT register.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PIN0 Pin 0
W1S
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Set 1 Write: a '1' sets the pin high; a '0' has no effect
B RW PIN1 Pin 1
W1S
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Set 1 Write: a '1' sets the pin high; a '0' has no effect
C RW PIN2 Pin 2
W1S
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Set 1 Write: a '1' sets the pin high; a '0' has no effect
D RW PIN3 Pin 3
W1S
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Set 1 Write: a '1' sets the pin high; a '0' has no effect
E RW PIN4 Pin 4
W1S
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Set 1 Write: a '1' sets the pin high; a '0' has no effect
F RW PIN5 Pin 5
W1S
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Set 1 Write: a '1' sets the pin high; a '0' has no effect
G RW PIN6 Pin 6
W1S
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Set 1 Write: a '1' sets the pin high; a '0' has no effect

4413_417 v1.9 247

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
H RW PIN7 Pin 7
W1S
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Set 1 Write: a '1' sets the pin high; a '0' has no effect
I RW PIN8 Pin 8
W1S
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Set 1 Write: a '1' sets the pin high; a '0' has no effect
J RW PIN9 Pin 9
W1S
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Set 1 Write: a '1' sets the pin high; a '0' has no effect
K RW PIN10 Pin 10
W1S
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Set 1 Write: a '1' sets the pin high; a '0' has no effect
L RW PIN11 Pin 11
W1S
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Set 1 Write: a '1' sets the pin high; a '0' has no effect
M RW PIN12 Pin 12
W1S
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Set 1 Write: a '1' sets the pin high; a '0' has no effect
N RW PIN13 Pin 13
W1S
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Set 1 Write: a '1' sets the pin high; a '0' has no effect
O RW PIN14 Pin 14
W1S
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Set 1 Write: a '1' sets the pin high; a '0' has no effect
P RW PIN15 Pin 15
W1S
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Set 1 Write: a '1' sets the pin high; a '0' has no effect
Q RW PIN16 Pin 16
W1S
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Set 1 Write: a '1' sets the pin high; a '0' has no effect

4413_417 v1.9 248

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
R RW PIN17 Pin 17
W1S
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Set 1 Write: a '1' sets the pin high; a '0' has no effect
S RW PIN18 Pin 18
W1S
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Set 1 Write: a '1' sets the pin high; a '0' has no effect
T RW PIN19 Pin 19
W1S
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Set 1 Write: a '1' sets the pin high; a '0' has no effect
U RW PIN20 Pin 20
W1S
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Set 1 Write: a '1' sets the pin high; a '0' has no effect
V RW PIN21 Pin 21
W1S
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Set 1 Write: a '1' sets the pin high; a '0' has no effect
W RW PIN22 Pin 22
W1S
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Set 1 Write: a '1' sets the pin high; a '0' has no effect
X RW PIN23 Pin 23
W1S
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Set 1 Write: a '1' sets the pin high; a '0' has no effect
Y RW PIN24 Pin 24
W1S
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Set 1 Write: a '1' sets the pin high; a '0' has no effect
Z RW PIN25 Pin 25
W1S
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Set 1 Write: a '1' sets the pin high; a '0' has no effect
a RW PIN26 Pin 26
W1S
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Set 1 Write: a '1' sets the pin high; a '0' has no effect

4413_417 v1.9 249

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
b RW PIN27 Pin 27
W1S
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Set 1 Write: a '1' sets the pin high; a '0' has no effect
c RW PIN28 Pin 28
W1S
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Set 1 Write: a '1' sets the pin high; a '0' has no effect
d RW PIN29 Pin 29
W1S
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Set 1 Write: a '1' sets the pin high; a '0' has no effect
e RW PIN30 Pin 30
W1S
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Set 1 Write: a '1' sets the pin high; a '0' has no effect
f RW PIN31 Pin 31
W1S
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Set 1 Write: a '1' sets the pin high; a '0' has no effect

6.9.2.3 OUTCLR
Address offset: 0x50C
Clear individual bits in GPIO port

Note: Read: reads value of OUT register.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PIN0 Pin 0
W1C
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Clear 1 Write: a '1' sets the pin low; a '0' has no effect
B RW PIN1 Pin 1
W1C
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Clear 1 Write: a '1' sets the pin low; a '0' has no effect
C RW PIN2 Pin 2
W1C

4413_417 v1.9 250

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Clear 1 Write: a '1' sets the pin low; a '0' has no effect
D RW PIN3 Pin 3
W1C
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Clear 1 Write: a '1' sets the pin low; a '0' has no effect
E RW PIN4 Pin 4
W1C
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Clear 1 Write: a '1' sets the pin low; a '0' has no effect
F RW PIN5 Pin 5
W1C
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Clear 1 Write: a '1' sets the pin low; a '0' has no effect
G RW PIN6 Pin 6
W1C
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Clear 1 Write: a '1' sets the pin low; a '0' has no effect
H RW PIN7 Pin 7
W1C
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Clear 1 Write: a '1' sets the pin low; a '0' has no effect
I RW PIN8 Pin 8
W1C
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Clear 1 Write: a '1' sets the pin low; a '0' has no effect
J RW PIN9 Pin 9
W1C
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Clear 1 Write: a '1' sets the pin low; a '0' has no effect
K RW PIN10 Pin 10
W1C
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Clear 1 Write: a '1' sets the pin low; a '0' has no effect
L RW PIN11 Pin 11
W1C
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Clear 1 Write: a '1' sets the pin low; a '0' has no effect
M RW PIN12 Pin 12
W1C

4413_417 v1.9 251

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Clear 1 Write: a '1' sets the pin low; a '0' has no effect
N RW PIN13 Pin 13
W1C
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Clear 1 Write: a '1' sets the pin low; a '0' has no effect
O RW PIN14 Pin 14
W1C
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Clear 1 Write: a '1' sets the pin low; a '0' has no effect
P RW PIN15 Pin 15
W1C
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Clear 1 Write: a '1' sets the pin low; a '0' has no effect
Q RW PIN16 Pin 16
W1C
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Clear 1 Write: a '1' sets the pin low; a '0' has no effect
R RW PIN17 Pin 17
W1C
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Clear 1 Write: a '1' sets the pin low; a '0' has no effect
S RW PIN18 Pin 18
W1C
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Clear 1 Write: a '1' sets the pin low; a '0' has no effect
T RW PIN19 Pin 19
W1C
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Clear 1 Write: a '1' sets the pin low; a '0' has no effect
U RW PIN20 Pin 20
W1C
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Clear 1 Write: a '1' sets the pin low; a '0' has no effect
V RW PIN21 Pin 21
W1C
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Clear 1 Write: a '1' sets the pin low; a '0' has no effect
W RW PIN22 Pin 22
W1C

4413_417 v1.9 252

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Clear 1 Write: a '1' sets the pin low; a '0' has no effect
X RW PIN23 Pin 23
W1C
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Clear 1 Write: a '1' sets the pin low; a '0' has no effect
Y RW PIN24 Pin 24
W1C
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Clear 1 Write: a '1' sets the pin low; a '0' has no effect
Z RW PIN25 Pin 25
W1C
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Clear 1 Write: a '1' sets the pin low; a '0' has no effect
a RW PIN26 Pin 26
W1C
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Clear 1 Write: a '1' sets the pin low; a '0' has no effect
b RW PIN27 Pin 27
W1C
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Clear 1 Write: a '1' sets the pin low; a '0' has no effect
c RW PIN28 Pin 28
W1C
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Clear 1 Write: a '1' sets the pin low; a '0' has no effect
d RW PIN29 Pin 29
W1C
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Clear 1 Write: a '1' sets the pin low; a '0' has no effect
e RW PIN30 Pin 30
W1C
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Clear 1 Write: a '1' sets the pin low; a '0' has no effect
f RW PIN31 Pin 31
W1C
Low 0 Read: pin driver is low
High 1 Read: pin driver is high
Clear 1 Write: a '1' sets the pin low; a '0' has no effect

4413_417 v1.9 253

 Peripherals

6.9.2.4 IN
Address offset: 0x510
Read GPIO port

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R PIN0 Pin 0
Low 0 Pin input is low
High 1 Pin input is high
B R PIN1 Pin 1
Low 0 Pin input is low
High 1 Pin input is high
C R PIN2 Pin 2
Low 0 Pin input is low
High 1 Pin input is high
D R PIN3 Pin 3
Low 0 Pin input is low
High 1 Pin input is high
E R PIN4 Pin 4
Low 0 Pin input is low
High 1 Pin input is high
F R PIN5 Pin 5
Low 0 Pin input is low
High 1 Pin input is high
G R PIN6 Pin 6
Low 0 Pin input is low
High 1 Pin input is high
H R PIN7 Pin 7
Low 0 Pin input is low
High 1 Pin input is high
I R PIN8 Pin 8
Low 0 Pin input is low
High 1 Pin input is high
J R PIN9 Pin 9
Low 0 Pin input is low
High 1 Pin input is high
K R PIN10 Pin 10
Low 0 Pin input is low
High 1 Pin input is high
L R PIN11 Pin 11
Low 0 Pin input is low
High 1 Pin input is high
M R PIN12 Pin 12
Low 0 Pin input is low
High 1 Pin input is high
N R PIN13 Pin 13
Low 0 Pin input is low
High 1 Pin input is high
O R PIN14 Pin 14
Low 0 Pin input is low

4413_417 v1.9 254

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
High 1 Pin input is high
P R PIN15 Pin 15
Low 0 Pin input is low
High 1 Pin input is high
Q R PIN16 Pin 16
Low 0 Pin input is low
High 1 Pin input is high
R R PIN17 Pin 17
Low 0 Pin input is low
High 1 Pin input is high
S R PIN18 Pin 18
Low 0 Pin input is low
High 1 Pin input is high
T R PIN19 Pin 19
Low 0 Pin input is low
High 1 Pin input is high
U R PIN20 Pin 20
Low 0 Pin input is low
High 1 Pin input is high
V R PIN21 Pin 21
Low 0 Pin input is low
High 1 Pin input is high
W R PIN22 Pin 22
Low 0 Pin input is low
High 1 Pin input is high
X R PIN23 Pin 23
Low 0 Pin input is low
High 1 Pin input is high
Y R PIN24 Pin 24
Low 0 Pin input is low
High 1 Pin input is high
Z R PIN25 Pin 25
Low 0 Pin input is low
High 1 Pin input is high
a R PIN26 Pin 26
Low 0 Pin input is low
High 1 Pin input is high
b R PIN27 Pin 27
Low 0 Pin input is low
High 1 Pin input is high
c R PIN28 Pin 28
Low 0 Pin input is low
High 1 Pin input is high
d R PIN29 Pin 29
Low 0 Pin input is low
High 1 Pin input is high
e R PIN30 Pin 30
Low 0 Pin input is low
High 1 Pin input is high
f R PIN31 Pin 31

4413_417 v1.9 255

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Low 0 Pin input is low
High 1 Pin input is high

6.9.2.5 DIR
Address offset: 0x514
Direction of GPIO pins

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PIN0 Pin 0
Input 0 Pin set as input
Output 1 Pin set as output
B RW PIN1 Pin 1
Input 0 Pin set as input
Output 1 Pin set as output
C RW PIN2 Pin 2
Input 0 Pin set as input
Output 1 Pin set as output
D RW PIN3 Pin 3
Input 0 Pin set as input
Output 1 Pin set as output
E RW PIN4 Pin 4
Input 0 Pin set as input
Output 1 Pin set as output
F RW PIN5 Pin 5
Input 0 Pin set as input
Output 1 Pin set as output
G RW PIN6 Pin 6
Input 0 Pin set as input
Output 1 Pin set as output
H RW PIN7 Pin 7
Input 0 Pin set as input
Output 1 Pin set as output
I RW PIN8 Pin 8
Input 0 Pin set as input
Output 1 Pin set as output
J RW PIN9 Pin 9
Input 0 Pin set as input
Output 1 Pin set as output
K RW PIN10 Pin 10
Input 0 Pin set as input
Output 1 Pin set as output
L RW PIN11 Pin 11
Input 0 Pin set as input
Output 1 Pin set as output
M RW PIN12 Pin 12

4413_417 v1.9 256

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Input 0 Pin set as input
Output 1 Pin set as output
N RW PIN13 Pin 13
Input 0 Pin set as input
Output 1 Pin set as output
O RW PIN14 Pin 14
Input 0 Pin set as input
Output 1 Pin set as output
P RW PIN15 Pin 15
Input 0 Pin set as input
Output 1 Pin set as output
Q RW PIN16 Pin 16
Input 0 Pin set as input
Output 1 Pin set as output
R RW PIN17 Pin 17
Input 0 Pin set as input
Output 1 Pin set as output
S RW PIN18 Pin 18
Input 0 Pin set as input
Output 1 Pin set as output
T RW PIN19 Pin 19
Input 0 Pin set as input
Output 1 Pin set as output
U RW PIN20 Pin 20
Input 0 Pin set as input
Output 1 Pin set as output
V RW PIN21 Pin 21
Input 0 Pin set as input
Output 1 Pin set as output
W RW PIN22 Pin 22
Input 0 Pin set as input
Output 1 Pin set as output
X RW PIN23 Pin 23
Input 0 Pin set as input
Output 1 Pin set as output
Y RW PIN24 Pin 24
Input 0 Pin set as input
Output 1 Pin set as output
Z RW PIN25 Pin 25
Input 0 Pin set as input
Output 1 Pin set as output
a RW PIN26 Pin 26
Input 0 Pin set as input
Output 1 Pin set as output
b RW PIN27 Pin 27
Input 0 Pin set as input
Output 1 Pin set as output
c RW PIN28 Pin 28
Input 0 Pin set as input
Output 1 Pin set as output

4413_417 v1.9 257

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
d RW PIN29 Pin 29
Input 0 Pin set as input
Output 1 Pin set as output
e RW PIN30 Pin 30
Input 0 Pin set as input
Output 1 Pin set as output
f RW PIN31 Pin 31
Input 0 Pin set as input
Output 1 Pin set as output

6.9.2.6 DIRSET
Address offset: 0x518
DIR set register

Note: Read: reads value of DIR register.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PIN0 Set as output pin 0
W1S
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Set 1 Write: a '1' sets pin to output; a '0' has no effect
B RW PIN1 Set as output pin 1
W1S
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Set 1 Write: a '1' sets pin to output; a '0' has no effect
C RW PIN2 Set as output pin 2
W1S
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Set 1 Write: a '1' sets pin to output; a '0' has no effect
D RW PIN3 Set as output pin 3
W1S
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Set 1 Write: a '1' sets pin to output; a '0' has no effect
E RW PIN4 Set as output pin 4
W1S
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Set 1 Write: a '1' sets pin to output; a '0' has no effect
F RW PIN5 Set as output pin 5
W1S
Input 0 Read: pin set as input

4413_417 v1.9 258

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Output 1 Read: pin set as output
Set 1 Write: a '1' sets pin to output; a '0' has no effect
G RW PIN6 Set as output pin 6
W1S
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Set 1 Write: a '1' sets pin to output; a '0' has no effect
H RW PIN7 Set as output pin 7
W1S
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Set 1 Write: a '1' sets pin to output; a '0' has no effect
I RW PIN8 Set as output pin 8
W1S
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Set 1 Write: a '1' sets pin to output; a '0' has no effect
J RW PIN9 Set as output pin 9
W1S
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Set 1 Write: a '1' sets pin to output; a '0' has no effect
K RW PIN10 Set as output pin 10
W1S
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Set 1 Write: a '1' sets pin to output; a '0' has no effect
L RW PIN11 Set as output pin 11
W1S
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Set 1 Write: a '1' sets pin to output; a '0' has no effect
M RW PIN12 Set as output pin 12
W1S
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Set 1 Write: a '1' sets pin to output; a '0' has no effect
N RW PIN13 Set as output pin 13
W1S
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Set 1 Write: a '1' sets pin to output; a '0' has no effect
O RW PIN14 Set as output pin 14
W1S
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Set 1 Write: a '1' sets pin to output; a '0' has no effect
P RW PIN15 Set as output pin 15
W1S
Input 0 Read: pin set as input

4413_417 v1.9 259

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Output 1 Read: pin set as output
Set 1 Write: a '1' sets pin to output; a '0' has no effect
Q RW PIN16 Set as output pin 16
W1S
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Set 1 Write: a '1' sets pin to output; a '0' has no effect
R RW PIN17 Set as output pin 17
W1S
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Set 1 Write: a '1' sets pin to output; a '0' has no effect
S RW PIN18 Set as output pin 18
W1S
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Set 1 Write: a '1' sets pin to output; a '0' has no effect
T RW PIN19 Set as output pin 19
W1S
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Set 1 Write: a '1' sets pin to output; a '0' has no effect
U RW PIN20 Set as output pin 20
W1S
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Set 1 Write: a '1' sets pin to output; a '0' has no effect
V RW PIN21 Set as output pin 21
W1S
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Set 1 Write: a '1' sets pin to output; a '0' has no effect
W RW PIN22 Set as output pin 22
W1S
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Set 1 Write: a '1' sets pin to output; a '0' has no effect
X RW PIN23 Set as output pin 23
W1S
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Set 1 Write: a '1' sets pin to output; a '0' has no effect
Y RW PIN24 Set as output pin 24
W1S
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Set 1 Write: a '1' sets pin to output; a '0' has no effect
Z RW PIN25 Set as output pin 25
W1S
Input 0 Read: pin set as input

4413_417 v1.9 260

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Output 1 Read: pin set as output
Set 1 Write: a '1' sets pin to output; a '0' has no effect
a RW PIN26 Set as output pin 26
W1S
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Set 1 Write: a '1' sets pin to output; a '0' has no effect
b RW PIN27 Set as output pin 27
W1S
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Set 1 Write: a '1' sets pin to output; a '0' has no effect
c RW PIN28 Set as output pin 28
W1S
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Set 1 Write: a '1' sets pin to output; a '0' has no effect
d RW PIN29 Set as output pin 29
W1S
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Set 1 Write: a '1' sets pin to output; a '0' has no effect
e RW PIN30 Set as output pin 30
W1S
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Set 1 Write: a '1' sets pin to output; a '0' has no effect
f RW PIN31 Set as output pin 31
W1S
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Set 1 Write: a '1' sets pin to output; a '0' has no effect

6.9.2.7 DIRCLR
Address offset: 0x51C
DIR clear register

Note: Read: reads value of DIR register.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PIN0 Set as input pin 0
W1C
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Clear 1 Write: a '1' sets pin to input; a '0' has no effect

4413_417 v1.9 261

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
B RW PIN1 Set as input pin 1
W1C
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Clear 1 Write: a '1' sets pin to input; a '0' has no effect
C RW PIN2 Set as input pin 2
W1C
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Clear 1 Write: a '1' sets pin to input; a '0' has no effect
D RW PIN3 Set as input pin 3
W1C
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Clear 1 Write: a '1' sets pin to input; a '0' has no effect
E RW PIN4 Set as input pin 4
W1C
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Clear 1 Write: a '1' sets pin to input; a '0' has no effect
F RW PIN5 Set as input pin 5
W1C
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Clear 1 Write: a '1' sets pin to input; a '0' has no effect
G RW PIN6 Set as input pin 6
W1C
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Clear 1 Write: a '1' sets pin to input; a '0' has no effect
H RW PIN7 Set as input pin 7
W1C
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Clear 1 Write: a '1' sets pin to input; a '0' has no effect
I RW PIN8 Set as input pin 8
W1C
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Clear 1 Write: a '1' sets pin to input; a '0' has no effect
J RW PIN9 Set as input pin 9
W1C
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Clear 1 Write: a '1' sets pin to input; a '0' has no effect
K RW PIN10 Set as input pin 10
W1C
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Clear 1 Write: a '1' sets pin to input; a '0' has no effect

4413_417 v1.9 262

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
L RW PIN11 Set as input pin 11
W1C
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Clear 1 Write: a '1' sets pin to input; a '0' has no effect
M RW PIN12 Set as input pin 12
W1C
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Clear 1 Write: a '1' sets pin to input; a '0' has no effect
N RW PIN13 Set as input pin 13
W1C
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Clear 1 Write: a '1' sets pin to input; a '0' has no effect
O RW PIN14 Set as input pin 14
W1C
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Clear 1 Write: a '1' sets pin to input; a '0' has no effect
P RW PIN15 Set as input pin 15
W1C
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Clear 1 Write: a '1' sets pin to input; a '0' has no effect
Q RW PIN16 Set as input pin 16
W1C
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Clear 1 Write: a '1' sets pin to input; a '0' has no effect
R RW PIN17 Set as input pin 17
W1C
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Clear 1 Write: a '1' sets pin to input; a '0' has no effect
S RW PIN18 Set as input pin 18
W1C
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Clear 1 Write: a '1' sets pin to input; a '0' has no effect
T RW PIN19 Set as input pin 19
W1C
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Clear 1 Write: a '1' sets pin to input; a '0' has no effect
U RW PIN20 Set as input pin 20
W1C
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Clear 1 Write: a '1' sets pin to input; a '0' has no effect

4413_417 v1.9 263

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
V RW PIN21 Set as input pin 21
W1C
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Clear 1 Write: a '1' sets pin to input; a '0' has no effect
W RW PIN22 Set as input pin 22
W1C
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Clear 1 Write: a '1' sets pin to input; a '0' has no effect
X RW PIN23 Set as input pin 23
W1C
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Clear 1 Write: a '1' sets pin to input; a '0' has no effect
Y RW PIN24 Set as input pin 24
W1C
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Clear 1 Write: a '1' sets pin to input; a '0' has no effect
Z RW PIN25 Set as input pin 25
W1C
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Clear 1 Write: a '1' sets pin to input; a '0' has no effect
a RW PIN26 Set as input pin 26
W1C
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Clear 1 Write: a '1' sets pin to input; a '0' has no effect
b RW PIN27 Set as input pin 27
W1C
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Clear 1 Write: a '1' sets pin to input; a '0' has no effect
c RW PIN28 Set as input pin 28
W1C
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Clear 1 Write: a '1' sets pin to input; a '0' has no effect
d RW PIN29 Set as input pin 29
W1C
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Clear 1 Write: a '1' sets pin to input; a '0' has no effect
e RW PIN30 Set as input pin 30
W1C
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Clear 1 Write: a '1' sets pin to input; a '0' has no effect

4413_417 v1.9 264

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
f RW PIN31 Set as input pin 31
W1C
Input 0 Read: pin set as input
Output 1 Read: pin set as output
Clear 1 Write: a '1' sets pin to input; a '0' has no effect

6.9.2.8 LATCH
Address offset: 0x520
Latch register indicating what GPIO pins that have met the criteria set in the PIN_CNF[n].SENSE registers

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PIN0 Status on whether PIN0 has met criteria set in PIN_CNF0.SENSE register.
Write '1' to clear.
NotLatched 0 Criteria has not been met
Latched 1 Criteria has been met
B RW PIN1 Status on whether PIN1 has met criteria set in PIN_CNF1.SENSE register.
Write '1' to clear.
NotLatched 0 Criteria has not been met
Latched 1 Criteria has been met
C RW PIN2 Status on whether PIN2 has met criteria set in PIN_CNF2.SENSE register.
Write '1' to clear.
NotLatched 0 Criteria has not been met
Latched 1 Criteria has been met
D RW PIN3 Status on whether PIN3 has met criteria set in PIN_CNF3.SENSE register.
Write '1' to clear.
NotLatched 0 Criteria has not been met
Latched 1 Criteria has been met
E RW PIN4 Status on whether PIN4 has met criteria set in PIN_CNF4.SENSE register.
Write '1' to clear.
NotLatched 0 Criteria has not been met
Latched 1 Criteria has been met
F RW PIN5 Status on whether PIN5 has met criteria set in PIN_CNF5.SENSE register.
Write '1' to clear.
NotLatched 0 Criteria has not been met
Latched 1 Criteria has been met
G RW PIN6 Status on whether PIN6 has met criteria set in PIN_CNF6.SENSE register.
Write '1' to clear.
NotLatched 0 Criteria has not been met
Latched 1 Criteria has been met
H RW PIN7 Status on whether PIN7 has met criteria set in PIN_CNF7.SENSE register.
Write '1' to clear.
NotLatched 0 Criteria has not been met
Latched 1 Criteria has been met
I RW PIN8 Status on whether PIN8 has met criteria set in PIN_CNF8.SENSE register.
Write '1' to clear.

4413_417 v1.9 265

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
NotLatched 0 Criteria has not been met
Latched 1 Criteria has been met
J RW PIN9 Status on whether PIN9 has met criteria set in PIN_CNF9.SENSE register.
Write '1' to clear.
NotLatched 0 Criteria has not been met
Latched 1 Criteria has been met
K RW PIN10 Status on whether PIN10 has met criteria set in PIN_CNF10.SENSE register.
Write '1' to clear.
NotLatched 0 Criteria has not been met
Latched 1 Criteria has been met
L RW PIN11 Status on whether PIN11 has met criteria set in PIN_CNF11.SENSE register.
Write '1' to clear.
NotLatched 0 Criteria has not been met
Latched 1 Criteria has been met
M RW PIN12 Status on whether PIN12 has met criteria set in PIN_CNF12.SENSE register.
Write '1' to clear.
NotLatched 0 Criteria has not been met
Latched 1 Criteria has been met
N RW PIN13 Status on whether PIN13 has met criteria set in PIN_CNF13.SENSE register.
Write '1' to clear.
NotLatched 0 Criteria has not been met
Latched 1 Criteria has been met
O RW PIN14 Status on whether PIN14 has met criteria set in PIN_CNF14.SENSE register.
Write '1' to clear.
NotLatched 0 Criteria has not been met
Latched 1 Criteria has been met
P RW PIN15 Status on whether PIN15 has met criteria set in PIN_CNF15.SENSE register.
Write '1' to clear.
NotLatched 0 Criteria has not been met
Latched 1 Criteria has been met
Q RW PIN16 Status on whether PIN16 has met criteria set in PIN_CNF16.SENSE register.
Write '1' to clear.
NotLatched 0 Criteria has not been met
Latched 1 Criteria has been met
R RW PIN17 Status on whether PIN17 has met criteria set in PIN_CNF17.SENSE register.
Write '1' to clear.
NotLatched 0 Criteria has not been met
Latched 1 Criteria has been met
S RW PIN18 Status on whether PIN18 has met criteria set in PIN_CNF18.SENSE register.
Write '1' to clear.
NotLatched 0 Criteria has not been met
Latched 1 Criteria has been met
T RW PIN19 Status on whether PIN19 has met criteria set in PIN_CNF19.SENSE register.
Write '1' to clear.
NotLatched 0 Criteria has not been met
Latched 1 Criteria has been met
U RW PIN20 Status on whether PIN20 has met criteria set in PIN_CNF20.SENSE register.
Write '1' to clear.
NotLatched 0 Criteria has not been met
Latched 1 Criteria has been met

4413_417 v1.9 266

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
V RW PIN21 Status on whether PIN21 has met criteria set in PIN_CNF21.SENSE register.
Write '1' to clear.
NotLatched 0 Criteria has not been met
Latched 1 Criteria has been met
W RW PIN22 Status on whether PIN22 has met criteria set in PIN_CNF22.SENSE register.
Write '1' to clear.
NotLatched 0 Criteria has not been met
Latched 1 Criteria has been met
X RW PIN23 Status on whether PIN23 has met criteria set in PIN_CNF23.SENSE register.
Write '1' to clear.
NotLatched 0 Criteria has not been met
Latched 1 Criteria has been met
Y RW PIN24 Status on whether PIN24 has met criteria set in PIN_CNF24.SENSE register.
Write '1' to clear.
NotLatched 0 Criteria has not been met
Latched 1 Criteria has been met
Z RW PIN25 Status on whether PIN25 has met criteria set in PIN_CNF25.SENSE register.
Write '1' to clear.
NotLatched 0 Criteria has not been met
Latched 1 Criteria has been met
a RW PIN26 Status on whether PIN26 has met criteria set in PIN_CNF26.SENSE register.
Write '1' to clear.
NotLatched 0 Criteria has not been met
Latched 1 Criteria has been met
b RW PIN27 Status on whether PIN27 has met criteria set in PIN_CNF27.SENSE register.
Write '1' to clear.
NotLatched 0 Criteria has not been met
Latched 1 Criteria has been met
c RW PIN28 Status on whether PIN28 has met criteria set in PIN_CNF28.SENSE register.
Write '1' to clear.
NotLatched 0 Criteria has not been met
Latched 1 Criteria has been met
d RW PIN29 Status on whether PIN29 has met criteria set in PIN_CNF29.SENSE register.
Write '1' to clear.
NotLatched 0 Criteria has not been met
Latched 1 Criteria has been met
e RW PIN30 Status on whether PIN30 has met criteria set in PIN_CNF30.SENSE register.
Write '1' to clear.
NotLatched 0 Criteria has not been met
Latched 1 Criteria has been met
f RW PIN31 Status on whether PIN31 has met criteria set in PIN_CNF31.SENSE register.
Write '1' to clear.
NotLatched 0 Criteria has not been met
Latched 1 Criteria has been met

6.9.2.9 DETECTMODE
Address offset: 0x524
Select between default DETECT signal behavior and LDETECT mode

4413_417 v1.9 267

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW DETECTMODE Select between default DETECT signal behavior and LDETECT mode
Default 0 DETECT directly connected to PIN DETECT signals
LDETECT 1 Use the latched LDETECT behavior

6.9.2.10 PIN_CNF[0]
Address offset: 0x700
Configuration of GPIO pins

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
A RW DIR Pin direction. Same physical register as DIR register
Input 0 Configure pin as an input pin
Output 1 Configure pin as an output pin
B RW INPUT Connect or disconnect input buffer
Connect 0 Connect input buffer
Disconnect 1 Disconnect input buffer
C RW PULL Pull configuration
Disabled 0 No pull
Pulldown 1 Pull down on pin
Pullup 3 Pull up on pin
D RW DRIVE Drive configuration
S0S1 0 Standard '0', standard '1'
H0S1 1 High drive '0', standard '1'
S0H1 2 Standard '0', high drive '1'
H0H1 3 High drive '0', high 'drive '1''
D0S1 4 Disconnect '0' standard '1' (normally used for wired-or connections)
D0H1 5 Disconnect '0', high drive '1' (normally used for wired-or connections)
S0D1 6 Standard '0'. disconnect '1' (normally used for wired-and connections)
H0D1 7 High drive '0', disconnect '1' (normally used for wired-and connections)
E RW SENSE Pin sensing mechanism
Disabled 0 Disabled
High 2 Sense for high level
Low 3 Sense for low level

6.9.2.11 PIN_CNF[1]
Address offset: 0x704
Configuration of GPIO pins

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
A RW DIR Pin direction. Same physical register as DIR register
Input 0 Configure pin as an input pin
Output 1 Configure pin as an output pin

4413_417 v1.9 268

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
B RW INPUT Connect or disconnect input buffer
Connect 0 Connect input buffer
Disconnect 1 Disconnect input buffer
C RW PULL Pull configuration
Disabled 0 No pull
Pulldown 1 Pull down on pin
Pullup 3 Pull up on pin
D RW DRIVE Drive configuration
S0S1 0 Standard '0', standard '1'
H0S1 1 High drive '0', standard '1'
S0H1 2 Standard '0', high drive '1'
H0H1 3 High drive '0', high 'drive '1''
D0S1 4 Disconnect '0' standard '1' (normally used for wired-or connections)
D0H1 5 Disconnect '0', high drive '1' (normally used for wired-or connections)
S0D1 6 Standard '0'. disconnect '1' (normally used for wired-and connections)
H0D1 7 High drive '0', disconnect '1' (normally used for wired-and connections)
E RW SENSE Pin sensing mechanism
Disabled 0 Disabled
High 2 Sense for high level
Low 3 Sense for low level

6.9.2.12 PIN_CNF[2]
Address offset: 0x708
Configuration of GPIO pins

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
A RW DIR Pin direction. Same physical register as DIR register
Input 0 Configure pin as an input pin
Output 1 Configure pin as an output pin
B RW INPUT Connect or disconnect input buffer
Connect 0 Connect input buffer
Disconnect 1 Disconnect input buffer
C RW PULL Pull configuration
Disabled 0 No pull
Pulldown 1 Pull down on pin
Pullup 3 Pull up on pin
D RW DRIVE Drive configuration
S0S1 0 Standard '0', standard '1'
H0S1 1 High drive '0', standard '1'
S0H1 2 Standard '0', high drive '1'
H0H1 3 High drive '0', high 'drive '1''
D0S1 4 Disconnect '0' standard '1' (normally used for wired-or connections)
D0H1 5 Disconnect '0', high drive '1' (normally used for wired-or connections)
S0D1 6 Standard '0'. disconnect '1' (normally used for wired-and connections)
H0D1 7 High drive '0', disconnect '1' (normally used for wired-and connections)

4413_417 v1.9 269

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
E RW SENSE Pin sensing mechanism
Disabled 0 Disabled
High 2 Sense for high level
Low 3 Sense for low level

6.9.2.13 PIN_CNF[3]
Address offset: 0x70C
Configuration of GPIO pins

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
A RW DIR Pin direction. Same physical register as DIR register
Input 0 Configure pin as an input pin
Output 1 Configure pin as an output pin
B RW INPUT Connect or disconnect input buffer
Connect 0 Connect input buffer
Disconnect 1 Disconnect input buffer
C RW PULL Pull configuration
Disabled 0 No pull
Pulldown 1 Pull down on pin
Pullup 3 Pull up on pin
D RW DRIVE Drive configuration
S0S1 0 Standard '0', standard '1'
H0S1 1 High drive '0', standard '1'
S0H1 2 Standard '0', high drive '1'
H0H1 3 High drive '0', high 'drive '1''
D0S1 4 Disconnect '0' standard '1' (normally used for wired-or connections)
D0H1 5 Disconnect '0', high drive '1' (normally used for wired-or connections)
S0D1 6 Standard '0'. disconnect '1' (normally used for wired-and connections)
H0D1 7 High drive '0', disconnect '1' (normally used for wired-and connections)
E RW SENSE Pin sensing mechanism
Disabled 0 Disabled
High 2 Sense for high level
Low 3 Sense for low level

6.9.2.14 PIN_CNF[4]
Address offset: 0x710
Configuration of GPIO pins

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
A RW DIR Pin direction. Same physical register as DIR register
Input 0 Configure pin as an input pin

4413_417 v1.9 270

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
Output 1 Configure pin as an output pin
B RW INPUT Connect or disconnect input buffer
Connect 0 Connect input buffer
Disconnect 1 Disconnect input buffer
C RW PULL Pull configuration
Disabled 0 No pull
Pulldown 1 Pull down on pin
Pullup 3 Pull up on pin
D RW DRIVE Drive configuration
S0S1 0 Standard '0', standard '1'
H0S1 1 High drive '0', standard '1'
S0H1 2 Standard '0', high drive '1'
H0H1 3 High drive '0', high 'drive '1''
D0S1 4 Disconnect '0' standard '1' (normally used for wired-or connections)
D0H1 5 Disconnect '0', high drive '1' (normally used for wired-or connections)
S0D1 6 Standard '0'. disconnect '1' (normally used for wired-and connections)
H0D1 7 High drive '0', disconnect '1' (normally used for wired-and connections)
E RW SENSE Pin sensing mechanism
Disabled 0 Disabled
High 2 Sense for high level
Low 3 Sense for low level

6.9.2.15 PIN_CNF[5]
Address offset: 0x714
Configuration of GPIO pins

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
A RW DIR Pin direction. Same physical register as DIR register
Input 0 Configure pin as an input pin
Output 1 Configure pin as an output pin
B RW INPUT Connect or disconnect input buffer
Connect 0 Connect input buffer
Disconnect 1 Disconnect input buffer
C RW PULL Pull configuration
Disabled 0 No pull
Pulldown 1 Pull down on pin
Pullup 3 Pull up on pin
D RW DRIVE Drive configuration
S0S1 0 Standard '0', standard '1'
H0S1 1 High drive '0', standard '1'
S0H1 2 Standard '0', high drive '1'
H0H1 3 High drive '0', high 'drive '1''
D0S1 4 Disconnect '0' standard '1' (normally used for wired-or connections)
D0H1 5 Disconnect '0', high drive '1' (normally used for wired-or connections)
S0D1 6 Standard '0'. disconnect '1' (normally used for wired-and connections)

4413_417 v1.9 271

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
H0D1 7 High drive '0', disconnect '1' (normally used for wired-and connections)
E RW SENSE Pin sensing mechanism
Disabled 0 Disabled
High 2 Sense for high level
Low 3 Sense for low level

6.9.2.16 PIN_CNF[6]
Address offset: 0x718
Configuration of GPIO pins

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
A RW DIR Pin direction. Same physical register as DIR register
Input 0 Configure pin as an input pin
Output 1 Configure pin as an output pin
B RW INPUT Connect or disconnect input buffer
Connect 0 Connect input buffer
Disconnect 1 Disconnect input buffer
C RW PULL Pull configuration
Disabled 0 No pull
Pulldown 1 Pull down on pin
Pullup 3 Pull up on pin
D RW DRIVE Drive configuration
S0S1 0 Standard '0', standard '1'
H0S1 1 High drive '0', standard '1'
S0H1 2 Standard '0', high drive '1'
H0H1 3 High drive '0', high 'drive '1''
D0S1 4 Disconnect '0' standard '1' (normally used for wired-or connections)
D0H1 5 Disconnect '0', high drive '1' (normally used for wired-or connections)
S0D1 6 Standard '0'. disconnect '1' (normally used for wired-and connections)
H0D1 7 High drive '0', disconnect '1' (normally used for wired-and connections)
E RW SENSE Pin sensing mechanism
Disabled 0 Disabled
High 2 Sense for high level
Low 3 Sense for low level

6.9.2.17 PIN_CNF[7]
Address offset: 0x71C
Configuration of GPIO pins

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
A RW DIR Pin direction. Same physical register as DIR register

4413_417 v1.9 272

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
Input 0 Configure pin as an input pin
Output 1 Configure pin as an output pin
B RW INPUT Connect or disconnect input buffer
Connect 0 Connect input buffer
Disconnect 1 Disconnect input buffer
C RW PULL Pull configuration
Disabled 0 No pull
Pulldown 1 Pull down on pin
Pullup 3 Pull up on pin
D RW DRIVE Drive configuration
S0S1 0 Standard '0', standard '1'
H0S1 1 High drive '0', standard '1'
S0H1 2 Standard '0', high drive '1'
H0H1 3 High drive '0', high 'drive '1''
D0S1 4 Disconnect '0' standard '1' (normally used for wired-or connections)
D0H1 5 Disconnect '0', high drive '1' (normally used for wired-or connections)
S0D1 6 Standard '0'. disconnect '1' (normally used for wired-and connections)
H0D1 7 High drive '0', disconnect '1' (normally used for wired-and connections)
E RW SENSE Pin sensing mechanism
Disabled 0 Disabled
High 2 Sense for high level
Low 3 Sense for low level

6.9.2.18 PIN_CNF[8]
Address offset: 0x720
Configuration of GPIO pins

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
A RW DIR Pin direction. Same physical register as DIR register
Input 0 Configure pin as an input pin
Output 1 Configure pin as an output pin
B RW INPUT Connect or disconnect input buffer
Connect 0 Connect input buffer
Disconnect 1 Disconnect input buffer
C RW PULL Pull configuration
Disabled 0 No pull
Pulldown 1 Pull down on pin
Pullup 3 Pull up on pin
D RW DRIVE Drive configuration
S0S1 0 Standard '0', standard '1'
H0S1 1 High drive '0', standard '1'
S0H1 2 Standard '0', high drive '1'
H0H1 3 High drive '0', high 'drive '1''
D0S1 4 Disconnect '0' standard '1' (normally used for wired-or connections)
D0H1 5 Disconnect '0', high drive '1' (normally used for wired-or connections)

4413_417 v1.9 273

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
S0D1 6 Standard '0'. disconnect '1' (normally used for wired-and connections)
H0D1 7 High drive '0', disconnect '1' (normally used for wired-and connections)
E RW SENSE Pin sensing mechanism
Disabled 0 Disabled
High 2 Sense for high level
Low 3 Sense for low level

6.9.2.19 PIN_CNF[9]
Address offset: 0x724
Configuration of GPIO pins

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
A RW DIR Pin direction. Same physical register as DIR register
Input 0 Configure pin as an input pin
Output 1 Configure pin as an output pin
B RW INPUT Connect or disconnect input buffer
Connect 0 Connect input buffer
Disconnect 1 Disconnect input buffer
C RW PULL Pull configuration
Disabled 0 No pull
Pulldown 1 Pull down on pin
Pullup 3 Pull up on pin
D RW DRIVE Drive configuration
S0S1 0 Standard '0', standard '1'
H0S1 1 High drive '0', standard '1'
S0H1 2 Standard '0', high drive '1'
H0H1 3 High drive '0', high 'drive '1''
D0S1 4 Disconnect '0' standard '1' (normally used for wired-or connections)
D0H1 5 Disconnect '0', high drive '1' (normally used for wired-or connections)
S0D1 6 Standard '0'. disconnect '1' (normally used for wired-and connections)
H0D1 7 High drive '0', disconnect '1' (normally used for wired-and connections)
E RW SENSE Pin sensing mechanism
Disabled 0 Disabled
High 2 Sense for high level
Low 3 Sense for low level

6.9.2.20 PIN_CNF[10]
Address offset: 0x728
Configuration of GPIO pins

4413_417 v1.9 274

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
A RW DIR Pin direction. Same physical register as DIR register
Input 0 Configure pin as an input pin
Output 1 Configure pin as an output pin
B RW INPUT Connect or disconnect input buffer
Connect 0 Connect input buffer
Disconnect 1 Disconnect input buffer
C RW PULL Pull configuration
Disabled 0 No pull
Pulldown 1 Pull down on pin
Pullup 3 Pull up on pin
D RW DRIVE Drive configuration
S0S1 0 Standard '0', standard '1'
H0S1 1 High drive '0', standard '1'
S0H1 2 Standard '0', high drive '1'
H0H1 3 High drive '0', high 'drive '1''
D0S1 4 Disconnect '0' standard '1' (normally used for wired-or connections)
D0H1 5 Disconnect '0', high drive '1' (normally used for wired-or connections)
S0D1 6 Standard '0'. disconnect '1' (normally used for wired-and connections)
H0D1 7 High drive '0', disconnect '1' (normally used for wired-and connections)
E RW SENSE Pin sensing mechanism
Disabled 0 Disabled
High 2 Sense for high level
Low 3 Sense for low level

6.9.2.21 PIN_CNF[11]
Address offset: 0x72C
Configuration of GPIO pins

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
A RW DIR Pin direction. Same physical register as DIR register
Input 0 Configure pin as an input pin
Output 1 Configure pin as an output pin
B RW INPUT Connect or disconnect input buffer
Connect 0 Connect input buffer
Disconnect 1 Disconnect input buffer
C RW PULL Pull configuration
Disabled 0 No pull
Pulldown 1 Pull down on pin
Pullup 3 Pull up on pin
D RW DRIVE Drive configuration
S0S1 0 Standard '0', standard '1'
H0S1 1 High drive '0', standard '1'
S0H1 2 Standard '0', high drive '1'
H0H1 3 High drive '0', high 'drive '1''
D0S1 4 Disconnect '0' standard '1' (normally used for wired-or connections)

4413_417 v1.9 275

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
D0H1 5 Disconnect '0', high drive '1' (normally used for wired-or connections)
S0D1 6 Standard '0'. disconnect '1' (normally used for wired-and connections)
H0D1 7 High drive '0', disconnect '1' (normally used for wired-and connections)
E RW SENSE Pin sensing mechanism
Disabled 0 Disabled
High 2 Sense for high level
Low 3 Sense for low level

6.9.2.22 PIN_CNF[12]
Address offset: 0x730
Configuration of GPIO pins

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
A RW DIR Pin direction. Same physical register as DIR register
Input 0 Configure pin as an input pin
Output 1 Configure pin as an output pin
B RW INPUT Connect or disconnect input buffer
Connect 0 Connect input buffer
Disconnect 1 Disconnect input buffer
C RW PULL Pull configuration
Disabled 0 No pull
Pulldown 1 Pull down on pin
Pullup 3 Pull up on pin
D RW DRIVE Drive configuration
S0S1 0 Standard '0', standard '1'
H0S1 1 High drive '0', standard '1'
S0H1 2 Standard '0', high drive '1'
H0H1 3 High drive '0', high 'drive '1''
D0S1 4 Disconnect '0' standard '1' (normally used for wired-or connections)
D0H1 5 Disconnect '0', high drive '1' (normally used for wired-or connections)
S0D1 6 Standard '0'. disconnect '1' (normally used for wired-and connections)
H0D1 7 High drive '0', disconnect '1' (normally used for wired-and connections)
E RW SENSE Pin sensing mechanism
Disabled 0 Disabled
High 2 Sense for high level
Low 3 Sense for low level

6.9.2.23 PIN_CNF[13]
Address offset: 0x734
Configuration of GPIO pins

4413_417 v1.9 276

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
A RW DIR Pin direction. Same physical register as DIR register
Input 0 Configure pin as an input pin
Output 1 Configure pin as an output pin
B RW INPUT Connect or disconnect input buffer
Connect 0 Connect input buffer
Disconnect 1 Disconnect input buffer
C RW PULL Pull configuration
Disabled 0 No pull
Pulldown 1 Pull down on pin
Pullup 3 Pull up on pin
D RW DRIVE Drive configuration
S0S1 0 Standard '0', standard '1'
H0S1 1 High drive '0', standard '1'
S0H1 2 Standard '0', high drive '1'
H0H1 3 High drive '0', high 'drive '1''
D0S1 4 Disconnect '0' standard '1' (normally used for wired-or connections)
D0H1 5 Disconnect '0', high drive '1' (normally used for wired-or connections)
S0D1 6 Standard '0'. disconnect '1' (normally used for wired-and connections)
H0D1 7 High drive '0', disconnect '1' (normally used for wired-and connections)
E RW SENSE Pin sensing mechanism
Disabled 0 Disabled
High 2 Sense for high level
Low 3 Sense for low level

6.9.2.24 PIN_CNF[14]
Address offset: 0x738
Configuration of GPIO pins

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
A RW DIR Pin direction. Same physical register as DIR register
Input 0 Configure pin as an input pin
Output 1 Configure pin as an output pin
B RW INPUT Connect or disconnect input buffer
Connect 0 Connect input buffer
Disconnect 1 Disconnect input buffer
C RW PULL Pull configuration
Disabled 0 No pull
Pulldown 1 Pull down on pin
Pullup 3 Pull up on pin
D RW DRIVE Drive configuration
S0S1 0 Standard '0', standard '1'
H0S1 1 High drive '0', standard '1'
S0H1 2 Standard '0', high drive '1'
H0H1 3 High drive '0', high 'drive '1''
D0S1 4 Disconnect '0' standard '1' (normally used for wired-or connections)

4413_417 v1.9 277

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
D0H1 5 Disconnect '0', high drive '1' (normally used for wired-or connections)
S0D1 6 Standard '0'. disconnect '1' (normally used for wired-and connections)
H0D1 7 High drive '0', disconnect '1' (normally used for wired-and connections)
E RW SENSE Pin sensing mechanism
Disabled 0 Disabled
High 2 Sense for high level
Low 3 Sense for low level

6.9.2.25 PIN_CNF[15]
Address offset: 0x73C
Configuration of GPIO pins

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
A RW DIR Pin direction. Same physical register as DIR register
Input 0 Configure pin as an input pin
Output 1 Configure pin as an output pin
B RW INPUT Connect or disconnect input buffer
Connect 0 Connect input buffer
Disconnect 1 Disconnect input buffer
C RW PULL Pull configuration
Disabled 0 No pull
Pulldown 1 Pull down on pin
Pullup 3 Pull up on pin
D RW DRIVE Drive configuration
S0S1 0 Standard '0', standard '1'
H0S1 1 High drive '0', standard '1'
S0H1 2 Standard '0', high drive '1'
H0H1 3 High drive '0', high 'drive '1''
D0S1 4 Disconnect '0' standard '1' (normally used for wired-or connections)
D0H1 5 Disconnect '0', high drive '1' (normally used for wired-or connections)
S0D1 6 Standard '0'. disconnect '1' (normally used for wired-and connections)
H0D1 7 High drive '0', disconnect '1' (normally used for wired-and connections)
E RW SENSE Pin sensing mechanism
Disabled 0 Disabled
High 2 Sense for high level
Low 3 Sense for low level

6.9.2.26 PIN_CNF[16]
Address offset: 0x740
Configuration of GPIO pins

4413_417 v1.9 278

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
A RW DIR Pin direction. Same physical register as DIR register
Input 0 Configure pin as an input pin
Output 1 Configure pin as an output pin
B RW INPUT Connect or disconnect input buffer
Connect 0 Connect input buffer
Disconnect 1 Disconnect input buffer
C RW PULL Pull configuration
Disabled 0 No pull
Pulldown 1 Pull down on pin
Pullup 3 Pull up on pin
D RW DRIVE Drive configuration
S0S1 0 Standard '0', standard '1'
H0S1 1 High drive '0', standard '1'
S0H1 2 Standard '0', high drive '1'
H0H1 3 High drive '0', high 'drive '1''
D0S1 4 Disconnect '0' standard '1' (normally used for wired-or connections)
D0H1 5 Disconnect '0', high drive '1' (normally used for wired-or connections)
S0D1 6 Standard '0'. disconnect '1' (normally used for wired-and connections)
H0D1 7 High drive '0', disconnect '1' (normally used for wired-and connections)
E RW SENSE Pin sensing mechanism
Disabled 0 Disabled
High 2 Sense for high level
Low 3 Sense for low level

6.9.2.27 PIN_CNF[17]
Address offset: 0x744
Configuration of GPIO pins

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
A RW DIR Pin direction. Same physical register as DIR register
Input 0 Configure pin as an input pin
Output 1 Configure pin as an output pin
B RW INPUT Connect or disconnect input buffer
Connect 0 Connect input buffer
Disconnect 1 Disconnect input buffer
C RW PULL Pull configuration
Disabled 0 No pull
Pulldown 1 Pull down on pin
Pullup 3 Pull up on pin
D RW DRIVE Drive configuration
S0S1 0 Standard '0', standard '1'
H0S1 1 High drive '0', standard '1'
S0H1 2 Standard '0', high drive '1'
H0H1 3 High drive '0', high 'drive '1''
D0S1 4 Disconnect '0' standard '1' (normally used for wired-or connections)

4413_417 v1.9 279

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
D0H1 5 Disconnect '0', high drive '1' (normally used for wired-or connections)
S0D1 6 Standard '0'. disconnect '1' (normally used for wired-and connections)
H0D1 7 High drive '0', disconnect '1' (normally used for wired-and connections)
E RW SENSE Pin sensing mechanism
Disabled 0 Disabled
High 2 Sense for high level
Low 3 Sense for low level

6.9.2.28 PIN_CNF[18]
Address offset: 0x748
Configuration of GPIO pins

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
A RW DIR Pin direction. Same physical register as DIR register
Input 0 Configure pin as an input pin
Output 1 Configure pin as an output pin
B RW INPUT Connect or disconnect input buffer
Connect 0 Connect input buffer
Disconnect 1 Disconnect input buffer
C RW PULL Pull configuration
Disabled 0 No pull
Pulldown 1 Pull down on pin
Pullup 3 Pull up on pin
D RW DRIVE Drive configuration
S0S1 0 Standard '0', standard '1'
H0S1 1 High drive '0', standard '1'
S0H1 2 Standard '0', high drive '1'
H0H1 3 High drive '0', high 'drive '1''
D0S1 4 Disconnect '0' standard '1' (normally used for wired-or connections)
D0H1 5 Disconnect '0', high drive '1' (normally used for wired-or connections)
S0D1 6 Standard '0'. disconnect '1' (normally used for wired-and connections)
H0D1 7 High drive '0', disconnect '1' (normally used for wired-and connections)
E RW SENSE Pin sensing mechanism
Disabled 0 Disabled
High 2 Sense for high level
Low 3 Sense for low level

6.9.2.29 PIN_CNF[19]
Address offset: 0x74C
Configuration of GPIO pins

4413_417 v1.9 280

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
A RW DIR Pin direction. Same physical register as DIR register
Input 0 Configure pin as an input pin
Output 1 Configure pin as an output pin
B RW INPUT Connect or disconnect input buffer
Connect 0 Connect input buffer
Disconnect 1 Disconnect input buffer
C RW PULL Pull configuration
Disabled 0 No pull
Pulldown 1 Pull down on pin
Pullup 3 Pull up on pin
D RW DRIVE Drive configuration
S0S1 0 Standard '0', standard '1'
H0S1 1 High drive '0', standard '1'
S0H1 2 Standard '0', high drive '1'
H0H1 3 High drive '0', high 'drive '1''
D0S1 4 Disconnect '0' standard '1' (normally used for wired-or connections)
D0H1 5 Disconnect '0', high drive '1' (normally used for wired-or connections)
S0D1 6 Standard '0'. disconnect '1' (normally used for wired-and connections)
H0D1 7 High drive '0', disconnect '1' (normally used for wired-and connections)
E RW SENSE Pin sensing mechanism
Disabled 0 Disabled
High 2 Sense for high level
Low 3 Sense for low level

6.9.2.30 PIN_CNF[20]
Address offset: 0x750
Configuration of GPIO pins

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
A RW DIR Pin direction. Same physical register as DIR register
Input 0 Configure pin as an input pin
Output 1 Configure pin as an output pin
B RW INPUT Connect or disconnect input buffer
Connect 0 Connect input buffer
Disconnect 1 Disconnect input buffer
C RW PULL Pull configuration
Disabled 0 No pull
Pulldown 1 Pull down on pin
Pullup 3 Pull up on pin
D RW DRIVE Drive configuration
S0S1 0 Standard '0', standard '1'
H0S1 1 High drive '0', standard '1'
S0H1 2 Standard '0', high drive '1'
H0H1 3 High drive '0', high 'drive '1''
D0S1 4 Disconnect '0' standard '1' (normally used for wired-or connections)

4413_417 v1.9 281

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
D0H1 5 Disconnect '0', high drive '1' (normally used for wired-or connections)
S0D1 6 Standard '0'. disconnect '1' (normally used for wired-and connections)
H0D1 7 High drive '0', disconnect '1' (normally used for wired-and connections)
E RW SENSE Pin sensing mechanism
Disabled 0 Disabled
High 2 Sense for high level
Low 3 Sense for low level

6.9.2.31 PIN_CNF[21]
Address offset: 0x754
Configuration of GPIO pins

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
A RW DIR Pin direction. Same physical register as DIR register
Input 0 Configure pin as an input pin
Output 1 Configure pin as an output pin
B RW INPUT Connect or disconnect input buffer
Connect 0 Connect input buffer
Disconnect 1 Disconnect input buffer
C RW PULL Pull configuration
Disabled 0 No pull
Pulldown 1 Pull down on pin
Pullup 3 Pull up on pin
D RW DRIVE Drive configuration
S0S1 0 Standard '0', standard '1'
H0S1 1 High drive '0', standard '1'
S0H1 2 Standard '0', high drive '1'
H0H1 3 High drive '0', high 'drive '1''
D0S1 4 Disconnect '0' standard '1' (normally used for wired-or connections)
D0H1 5 Disconnect '0', high drive '1' (normally used for wired-or connections)
S0D1 6 Standard '0'. disconnect '1' (normally used for wired-and connections)
H0D1 7 High drive '0', disconnect '1' (normally used for wired-and connections)
E RW SENSE Pin sensing mechanism
Disabled 0 Disabled
High 2 Sense for high level
Low 3 Sense for low level

6.9.2.32 PIN_CNF[22]
Address offset: 0x758
Configuration of GPIO pins

4413_417 v1.9 282

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
A RW DIR Pin direction. Same physical register as DIR register
Input 0 Configure pin as an input pin
Output 1 Configure pin as an output pin
B RW INPUT Connect or disconnect input buffer
Connect 0 Connect input buffer
Disconnect 1 Disconnect input buffer
C RW PULL Pull configuration
Disabled 0 No pull
Pulldown 1 Pull down on pin
Pullup 3 Pull up on pin
D RW DRIVE Drive configuration
S0S1 0 Standard '0', standard '1'
H0S1 1 High drive '0', standard '1'
S0H1 2 Standard '0', high drive '1'
H0H1 3 High drive '0', high 'drive '1''
D0S1 4 Disconnect '0' standard '1' (normally used for wired-or connections)
D0H1 5 Disconnect '0', high drive '1' (normally used for wired-or connections)
S0D1 6 Standard '0'. disconnect '1' (normally used for wired-and connections)
H0D1 7 High drive '0', disconnect '1' (normally used for wired-and connections)
E RW SENSE Pin sensing mechanism
Disabled 0 Disabled
High 2 Sense for high level
Low 3 Sense for low level

6.9.2.33 PIN_CNF[23]
Address offset: 0x75C
Configuration of GPIO pins

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
A RW DIR Pin direction. Same physical register as DIR register
Input 0 Configure pin as an input pin
Output 1 Configure pin as an output pin
B RW INPUT Connect or disconnect input buffer
Connect 0 Connect input buffer
Disconnect 1 Disconnect input buffer
C RW PULL Pull configuration
Disabled 0 No pull
Pulldown 1 Pull down on pin
Pullup 3 Pull up on pin
D RW DRIVE Drive configuration
S0S1 0 Standard '0', standard '1'
H0S1 1 High drive '0', standard '1'
S0H1 2 Standard '0', high drive '1'
H0H1 3 High drive '0', high 'drive '1''
D0S1 4 Disconnect '0' standard '1' (normally used for wired-or connections)

4413_417 v1.9 283

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
D0H1 5 Disconnect '0', high drive '1' (normally used for wired-or connections)
S0D1 6 Standard '0'. disconnect '1' (normally used for wired-and connections)
H0D1 7 High drive '0', disconnect '1' (normally used for wired-and connections)
E RW SENSE Pin sensing mechanism
Disabled 0 Disabled
High 2 Sense for high level
Low 3 Sense for low level

6.9.2.34 PIN_CNF[24]
Address offset: 0x760
Configuration of GPIO pins

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
A RW DIR Pin direction. Same physical register as DIR register
Input 0 Configure pin as an input pin
Output 1 Configure pin as an output pin
B RW INPUT Connect or disconnect input buffer
Connect 0 Connect input buffer
Disconnect 1 Disconnect input buffer
C RW PULL Pull configuration
Disabled 0 No pull
Pulldown 1 Pull down on pin
Pullup 3 Pull up on pin
D RW DRIVE Drive configuration
S0S1 0 Standard '0', standard '1'
H0S1 1 High drive '0', standard '1'
S0H1 2 Standard '0', high drive '1'
H0H1 3 High drive '0', high 'drive '1''
D0S1 4 Disconnect '0' standard '1' (normally used for wired-or connections)
D0H1 5 Disconnect '0', high drive '1' (normally used for wired-or connections)
S0D1 6 Standard '0'. disconnect '1' (normally used for wired-and connections)
H0D1 7 High drive '0', disconnect '1' (normally used for wired-and connections)
E RW SENSE Pin sensing mechanism
Disabled 0 Disabled
High 2 Sense for high level
Low 3 Sense for low level

6.9.2.35 PIN_CNF[25]
Address offset: 0x764
Configuration of GPIO pins

4413_417 v1.9 284

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
A RW DIR Pin direction. Same physical register as DIR register
Input 0 Configure pin as an input pin
Output 1 Configure pin as an output pin
B RW INPUT Connect or disconnect input buffer
Connect 0 Connect input buffer
Disconnect 1 Disconnect input buffer
C RW PULL Pull configuration
Disabled 0 No pull
Pulldown 1 Pull down on pin
Pullup 3 Pull up on pin
D RW DRIVE Drive configuration
S0S1 0 Standard '0', standard '1'
H0S1 1 High drive '0', standard '1'
S0H1 2 Standard '0', high drive '1'
H0H1 3 High drive '0', high 'drive '1''
D0S1 4 Disconnect '0' standard '1' (normally used for wired-or connections)
D0H1 5 Disconnect '0', high drive '1' (normally used for wired-or connections)
S0D1 6 Standard '0'. disconnect '1' (normally used for wired-and connections)
H0D1 7 High drive '0', disconnect '1' (normally used for wired-and connections)
E RW SENSE Pin sensing mechanism
Disabled 0 Disabled
High 2 Sense for high level
Low 3 Sense for low level

6.9.2.36 PIN_CNF[26]
Address offset: 0x768
Configuration of GPIO pins

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
A RW DIR Pin direction. Same physical register as DIR register
Input 0 Configure pin as an input pin
Output 1 Configure pin as an output pin
B RW INPUT Connect or disconnect input buffer
Connect 0 Connect input buffer
Disconnect 1 Disconnect input buffer
C RW PULL Pull configuration
Disabled 0 No pull
Pulldown 1 Pull down on pin
Pullup 3 Pull up on pin
D RW DRIVE Drive configuration
S0S1 0 Standard '0', standard '1'
H0S1 1 High drive '0', standard '1'
S0H1 2 Standard '0', high drive '1'
H0H1 3 High drive '0', high 'drive '1''
D0S1 4 Disconnect '0' standard '1' (normally used for wired-or connections)

4413_417 v1.9 285

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
D0H1 5 Disconnect '0', high drive '1' (normally used for wired-or connections)
S0D1 6 Standard '0'. disconnect '1' (normally used for wired-and connections)
H0D1 7 High drive '0', disconnect '1' (normally used for wired-and connections)
E RW SENSE Pin sensing mechanism
Disabled 0 Disabled
High 2 Sense for high level
Low 3 Sense for low level

6.9.2.37 PIN_CNF[27]
Address offset: 0x76C
Configuration of GPIO pins

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
A RW DIR Pin direction. Same physical register as DIR register
Input 0 Configure pin as an input pin
Output 1 Configure pin as an output pin
B RW INPUT Connect or disconnect input buffer
Connect 0 Connect input buffer
Disconnect 1 Disconnect input buffer
C RW PULL Pull configuration
Disabled 0 No pull
Pulldown 1 Pull down on pin
Pullup 3 Pull up on pin
D RW DRIVE Drive configuration
S0S1 0 Standard '0', standard '1'
H0S1 1 High drive '0', standard '1'
S0H1 2 Standard '0', high drive '1'
H0H1 3 High drive '0', high 'drive '1''
D0S1 4 Disconnect '0' standard '1' (normally used for wired-or connections)
D0H1 5 Disconnect '0', high drive '1' (normally used for wired-or connections)
S0D1 6 Standard '0'. disconnect '1' (normally used for wired-and connections)
H0D1 7 High drive '0', disconnect '1' (normally used for wired-and connections)
E RW SENSE Pin sensing mechanism
Disabled 0 Disabled
High 2 Sense for high level
Low 3 Sense for low level

6.9.2.38 PIN_CNF[28]
Address offset: 0x770
Configuration of GPIO pins

4413_417 v1.9 286

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
A RW DIR Pin direction. Same physical register as DIR register
Input 0 Configure pin as an input pin
Output 1 Configure pin as an output pin
B RW INPUT Connect or disconnect input buffer
Connect 0 Connect input buffer
Disconnect 1 Disconnect input buffer
C RW PULL Pull configuration
Disabled 0 No pull
Pulldown 1 Pull down on pin
Pullup 3 Pull up on pin
D RW DRIVE Drive configuration
S0S1 0 Standard '0', standard '1'
H0S1 1 High drive '0', standard '1'
S0H1 2 Standard '0', high drive '1'
H0H1 3 High drive '0', high 'drive '1''
D0S1 4 Disconnect '0' standard '1' (normally used for wired-or connections)
D0H1 5 Disconnect '0', high drive '1' (normally used for wired-or connections)
S0D1 6 Standard '0'. disconnect '1' (normally used for wired-and connections)
H0D1 7 High drive '0', disconnect '1' (normally used for wired-and connections)
E RW SENSE Pin sensing mechanism
Disabled 0 Disabled
High 2 Sense for high level
Low 3 Sense for low level

6.9.2.39 PIN_CNF[29]
Address offset: 0x774
Configuration of GPIO pins

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
A RW DIR Pin direction. Same physical register as DIR register
Input 0 Configure pin as an input pin
Output 1 Configure pin as an output pin
B RW INPUT Connect or disconnect input buffer
Connect 0 Connect input buffer
Disconnect 1 Disconnect input buffer
C RW PULL Pull configuration
Disabled 0 No pull
Pulldown 1 Pull down on pin
Pullup 3 Pull up on pin
D RW DRIVE Drive configuration
S0S1 0 Standard '0', standard '1'
H0S1 1 High drive '0', standard '1'
S0H1 2 Standard '0', high drive '1'
H0H1 3 High drive '0', high 'drive '1''
D0S1 4 Disconnect '0' standard '1' (normally used for wired-or connections)

4413_417 v1.9 287

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
D0H1 5 Disconnect '0', high drive '1' (normally used for wired-or connections)
S0D1 6 Standard '0'. disconnect '1' (normally used for wired-and connections)
H0D1 7 High drive '0', disconnect '1' (normally used for wired-and connections)
E RW SENSE Pin sensing mechanism
Disabled 0 Disabled
High 2 Sense for high level
Low 3 Sense for low level

6.9.2.40 PIN_CNF[30]
Address offset: 0x778
Configuration of GPIO pins

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
A RW DIR Pin direction. Same physical register as DIR register
Input 0 Configure pin as an input pin
Output 1 Configure pin as an output pin
B RW INPUT Connect or disconnect input buffer
Connect 0 Connect input buffer
Disconnect 1 Disconnect input buffer
C RW PULL Pull configuration
Disabled 0 No pull
Pulldown 1 Pull down on pin
Pullup 3 Pull up on pin
D RW DRIVE Drive configuration
S0S1 0 Standard '0', standard '1'
H0S1 1 High drive '0', standard '1'
S0H1 2 Standard '0', high drive '1'
H0H1 3 High drive '0', high 'drive '1''
D0S1 4 Disconnect '0' standard '1' (normally used for wired-or connections)
D0H1 5 Disconnect '0', high drive '1' (normally used for wired-or connections)
S0D1 6 Standard '0'. disconnect '1' (normally used for wired-and connections)
H0D1 7 High drive '0', disconnect '1' (normally used for wired-and connections)
E RW SENSE Pin sensing mechanism
Disabled 0 Disabled
High 2 Sense for high level
Low 3 Sense for low level

6.9.2.41 PIN_CNF[31]
Address offset: 0x77C
Configuration of GPIO pins

4413_417 v1.9 288

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E D D D C C B A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
A RW DIR Pin direction. Same physical register as DIR register
Input 0 Configure pin as an input pin
Output 1 Configure pin as an output pin
B RW INPUT Connect or disconnect input buffer
Connect 0 Connect input buffer
Disconnect 1 Disconnect input buffer
C RW PULL Pull configuration
Disabled 0 No pull
Pulldown 1 Pull down on pin
Pullup 3 Pull up on pin
D RW DRIVE Drive configuration
S0S1 0 Standard '0', standard '1'
H0S1 1 High drive '0', standard '1'
S0H1 2 Standard '0', high drive '1'
H0H1 3 High drive '0', high 'drive '1''
D0S1 4 Disconnect '0' standard '1' (normally used for wired-or connections)
D0H1 5 Disconnect '0', high drive '1' (normally used for wired-or connections)
S0D1 6 Standard '0'. disconnect '1' (normally used for wired-and connections)
H0D1 7 High drive '0', disconnect '1' (normally used for wired-and connections)
E RW SENSE Pin sensing mechanism
Disabled 0 Disabled
High 2 Sense for high level
Low 3 Sense for low level

6.9.3 Electrical specification

6.9.3.1 GPIO Electrical Specification

Symbol Description Min. Typ. Max. Units

VIH Input high voltage 0.7 x VDD VDD V
VIL Input low voltage VSS 0.3 x VDD V
VOH,SD Output high voltage, standard drive, 0.5 mA, VDD ≥ 1.7 VDD - 0.4 VDD V
VOH,HDH Output high voltage, high drive, 5 mA, VDD ≥ 2.7 V VDD - 0.4 VDD V
VOH,HDL Output high voltage, high drive, 3 mA, VDD ≥ 1.7 V VDD - 0.4 VDD V
VOL,SD Output low voltage, standard drive, 0.5 mA, VDD ≥ 1.7 VSS VSS + 0.4 V
VOL,HDH Output low voltage, high drive, 5 mA, VDD ≥ 2.7 V VSS VSS + 0.4 V
VOL,HDL Output low voltage, high drive, 3 mA, VDD ≥ 1.7 V VSS VSS + 0.4 V
IOL,SD Current at VSS+0.4 V, output set low, standard drive, VDD ≥ 1.7 1 2 4 mA
IOL,HDH Current at VSS+0.4 V, output set low, high drive, VDD ≥ 2.7 V 6 10 15 mA
IOL,HDL Current at VSS+0.4 V, output set low, high drive, VDD ≥ 1.7 V 3 mA
IOH,SD Current at VDD-0.4 V, output set high, standard drive, VDD ≥ 1.7 1 2 4 mA
IOH,HDH Current at VDD-0.4 V, output set high, high drive, VDD ≥ 2.7 V 6 9 14 mA
IOH,HDL Current at VDD-0.4 V, output set high, high drive, VDD ≥ 1.7 V 3 mA
tRF,15pF Rise/fall time, standard drive mode, 10-90%, 15 pF load 16 9 ns

tRF,25pF Rise/fall time, standard drive mode, 10-90%, 25 pF load16 13 ns

tRF,50pF Rise/fall time, standard drive mode, 10-90%, 50 pF load16 25 ns

tHRF,15pF Rise/Fall time, high drive mode, 10-90%, 15 pF load 16 4 ns

16
Rise and fall times based on simulations

4413_417 v1.9 289

 Peripherals

Symbol Description Min. Typ. Max. Units

tHRF,25pF 16
Rise/Fall time, high drive mode, 10-90%, 25 pF load 5 ns

tHRF,50pF 16
Rise/Fall time, high drive mode, 10-90%, 50 pF load 8 ns

RPU Pull-up resistance 11 13 16 kΩ

RPD Pull-down resistance 11 13 16 kΩ
CPAD Pad capacitance 3 pF

6.9.3.2 NFC Pads Electrical Specification

Symbol Description Min. Typ. Max. Units

CPAD_NFC Pad capacitance on NFC pads 4 pF
INFC_LEAK Leakage current between NFC pads when driven to different states 1 10 µA

6.10 GPIOTE — GPIO tasks and events

The GPIO tasks and events (GPIOTE) module provides functionality for accessing GPIO pins using tasks and
events. Each GPIOTE channel can be assigned to one pin.
A GPIOTE block enables GPIOs to generate events on pin state change which can be used to carry out tasks
through the PPI system. A GPIO can also be driven to change state on system events using the PPI system.
Tasks and events are briefly introduced in Peripheral interface on page 172, and GPIO is described in
more detail in GPIO — General purpose input/output on page 240.
Low power detection of pin state changes is possible when in System ON or System OFF.

Instance Number of GPIOTE channels

GPIOTE 8

Table 19: GPIOTE properties

Up to three tasks can be used in each GPIOTE channel for performing write operations to a pin. Two tasks
are fixed (SET and CLR), and one (OUT) is configurable to perform following operations:
• Set
• Clear
• Toggle
An event can be generated in each GPIOTE channel from one of the following input conditions:
• Rising edge
• Falling edge
• Any change

6.10.1 Pin events and tasks

The GPIOTE module has a number of tasks and events that can be configured to operate on individual
GPIO pins.
The tasks SET[n], CLR[n], and OUT[n] can write to individual pins, and events IN[n] can be generated from
input changes of individual pins.
The SET task will set the pin selected in GPIOTE.CONFIG[n].PSEL to high. The CLR task will set the pin low.
The effect of the OUT task on the pin is configurable in CONFIG[n].POLARITY. It can set the pin high, set it
low, or toggle it.

4413_417 v1.9 290

 Peripherals

Tasks and events are configured using the CONFIG[n] registers. One CONFIG[n] register is associated with a
set of SET[n], CLR[n], and OUT[n] tasks and IN[n] events.
As long as a SET[n], CLR[n], and OUT[n] task or an IN[n] event is configured to control pin n, the pin's
output value will only be updated by the GPIOTE module. The pin's output value, as specified in the GPIO,
will be ignored as long as the pin is controlled by GPIOTE. Attempting to write to the pin as a normal GPIO
pin will have no effect. When the GPIOTE is disconnected from a pin, the associated pin gets the output
and configuration values specified in the GPIO module, see MODE field in CONFIG[n] register.
When conflicting tasks are triggered simultaneously (i.e. during the same clock cycle) in one channel, the
priority of the tasks is as described in the following table.

Priority Task

1 OUT
2 CLR
3 SET

Table 20: Task priorities

When setting the CONFIG[n] registers, MODE=Disabled does not have the same effect as MODE=Task and
POLARITY=None. In the latter case, a CLR or SET task occurring at the exact same time as OUT will end up
with no change on the pin, based on the priorities described in the table above.
When a GPIOTE channel is configured to operate on a pin as a task, the initial value of that pin is
configured in the OUTINIT field of CONFIG[n].

6.10.2 Port event

PORT is an event that can be generated from multiple input pins using the GPIO DETECT signal.
The event will be generated on the rising edge of the DETECT signal. See GPIO — General purpose input/
output on page 240 for more information about the DETECT signal.
The GPIO DETECT signal will not wake the system up again if the system is put into System ON IDLE while
the DETECT signal is high. Clear all DETECT sources before entering sleep. If the LATCH register is used as
a source, a new rising edge will be generated on DETECT if any bit in LATCH is still high after clearing all
or part of the register. This could occur if one of the PINx.DETECT signals is still high, for example. See Pin
configuration on page 241 for more information.
Setting the system to System OFF while DETECT is high will cause a wakeup from System OFF reset.
This feature is always enabled even if the peripheral itself appears to be IDLE, meaning no clocks or
other power intensive infrastructure have to be requested to keep this feature enabled. This feature can
therefore be used to wake up the CPU from a WFI or WFE type sleep in System ON when all peripherals
and the CPU are idle, meaning the lowest power consumption in System ON mode.
In order to prevent spurious interrupts from the PORT event while configuring the sources, the following
must be performed:
1. Disable interrupts on the PORT event (through INTENCLR.PORT).
2. Configure the sources (PIN_CNF[n].SENSE).
3. Clear any potential event that could have occurred during configuration (write '0' to EVENTS_PORT).
4. Enable interrupts (through INTENSET.PORT).

6.10.3 Tasks and events pin configuration

Each GPIOTE channel is associated with one physical GPIO pin through the CONFIG.PSEL field.
When Event mode is selected in CONFIG.MODE, the pin specified by CONFIG.PSEL will be configured
as an input, overriding the DIR setting in GPIO. Similarly, when Task mode is selected in CONFIG.MODE,

4413_417 v1.9 291

 Peripherals

the pin specified by CONFIG.PSEL will be configured as an output overriding the DIR setting and OUT
value in GPIO. When Disabled is selected in CONFIG.MODE, the pin specified by CONFIG.PSEL will use its
configuration from the PIN[n].CNF registers in GPIO.

Note: A pin can only be assigned to one GPIOTE channel at a time. Failing to do so may result in
unpredictable behavior.

6.10.4 Registers
Instances

Instance Base address Description

GPIOTE 0x40006000 GPIO tasks and events

Register overview

Register Offset Description

TASKS_OUT[0] 0x000 Task for writing to pin specified in CONFIG[0].PSEL. Action on pin is configured in
CONFIG[0].POLARITY.
TASKS_OUT[1] 0x004 Task for writing to pin specified in CONFIG[1].PSEL. Action on pin is configured in
CONFIG[1].POLARITY.
TASKS_OUT[2] 0x008 Task for writing to pin specified in CONFIG[2].PSEL. Action on pin is configured in
CONFIG[2].POLARITY.
TASKS_OUT[3] 0x00C Task for writing to pin specified in CONFIG[3].PSEL. Action on pin is configured in
CONFIG[3].POLARITY.
TASKS_OUT[4] 0x010 Task for writing to pin specified in CONFIG[4].PSEL. Action on pin is configured in
CONFIG[4].POLARITY.
TASKS_OUT[5] 0x014 Task for writing to pin specified in CONFIG[5].PSEL. Action on pin is configured in
CONFIG[5].POLARITY.
TASKS_OUT[6] 0x018 Task for writing to pin specified in CONFIG[6].PSEL. Action on pin is configured in
CONFIG[6].POLARITY.
TASKS_OUT[7] 0x01C Task for writing to pin specified in CONFIG[7].PSEL. Action on pin is configured in
CONFIG[7].POLARITY.
TASKS_SET[0] 0x030 Task for writing to pin specified in CONFIG[0].PSEL. Action on pin is to set it high.
TASKS_SET[1] 0x034 Task for writing to pin specified in CONFIG[1].PSEL. Action on pin is to set it high.
TASKS_SET[2] 0x038 Task for writing to pin specified in CONFIG[2].PSEL. Action on pin is to set it high.
TASKS_SET[3] 0x03C Task for writing to pin specified in CONFIG[3].PSEL. Action on pin is to set it high.
TASKS_SET[4] 0x040 Task for writing to pin specified in CONFIG[4].PSEL. Action on pin is to set it high.
TASKS_SET[5] 0x044 Task for writing to pin specified in CONFIG[5].PSEL. Action on pin is to set it high.
TASKS_SET[6] 0x048 Task for writing to pin specified in CONFIG[6].PSEL. Action on pin is to set it high.
TASKS_SET[7] 0x04C Task for writing to pin specified in CONFIG[7].PSEL. Action on pin is to set it high.
TASKS_CLR[0] 0x060 Task for writing to pin specified in CONFIG[0].PSEL. Action on pin is to set it low.
TASKS_CLR[1] 0x064 Task for writing to pin specified in CONFIG[1].PSEL. Action on pin is to set it low.
TASKS_CLR[2] 0x068 Task for writing to pin specified in CONFIG[2].PSEL. Action on pin is to set it low.
TASKS_CLR[3] 0x06C Task for writing to pin specified in CONFIG[3].PSEL. Action on pin is to set it low.
TASKS_CLR[4] 0x070 Task for writing to pin specified in CONFIG[4].PSEL. Action on pin is to set it low.
TASKS_CLR[5] 0x074 Task for writing to pin specified in CONFIG[5].PSEL. Action on pin is to set it low.
TASKS_CLR[6] 0x078 Task for writing to pin specified in CONFIG[6].PSEL. Action on pin is to set it low.
TASKS_CLR[7] 0x07C Task for writing to pin specified in CONFIG[7].PSEL. Action on pin is to set it low.
EVENTS_IN[0] 0x100 Event generated from pin specified in CONFIG[0].PSEL
EVENTS_IN[1] 0x104 Event generated from pin specified in CONFIG[1].PSEL
EVENTS_IN[2] 0x108 Event generated from pin specified in CONFIG[2].PSEL

4413_417 v1.9 292

 Peripherals

Register Offset Description

EVENTS_IN[3] 0x10C Event generated from pin specified in CONFIG[3].PSEL
EVENTS_IN[4] 0x110 Event generated from pin specified in CONFIG[4].PSEL
EVENTS_IN[5] 0x114 Event generated from pin specified in CONFIG[5].PSEL
EVENTS_IN[6] 0x118 Event generated from pin specified in CONFIG[6].PSEL
EVENTS_IN[7] 0x11C Event generated from pin specified in CONFIG[7].PSEL
EVENTS_PORT 0x17C Event generated from multiple input GPIO pins with SENSE mechanism enabled
INTENSET 0x304 Enable interrupt
INTENCLR 0x308 Disable interrupt
CONFIG[0] 0x510 Configuration for OUT[n], SET[n], and CLR[n] tasks and IN[n] event
CONFIG[1] 0x514 Configuration for OUT[n], SET[n], and CLR[n] tasks and IN[n] event
CONFIG[2] 0x518 Configuration for OUT[n], SET[n], and CLR[n] tasks and IN[n] event
CONFIG[3] 0x51C Configuration for OUT[n], SET[n], and CLR[n] tasks and IN[n] event
CONFIG[4] 0x520 Configuration for OUT[n], SET[n], and CLR[n] tasks and IN[n] event
CONFIG[5] 0x524 Configuration for OUT[n], SET[n], and CLR[n] tasks and IN[n] event
CONFIG[6] 0x528 Configuration for OUT[n], SET[n], and CLR[n] tasks and IN[n] event
CONFIG[7] 0x52C Configuration for OUT[n], SET[n], and CLR[n] tasks and IN[n] event

6.10.4.1 TASKS_OUT[0]
Address offset: 0x000
Task for writing to pin specified in CONFIG[0].PSEL. Action on pin is configured in CONFIG[0].POLARITY.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_OUT Task for writing to pin specified in CONFIG[0].PSEL. Action on pin is
configured in CONFIG[0].POLARITY.
Trigger 1 Trigger task

6.10.4.2 TASKS_OUT[1]
Address offset: 0x004
Task for writing to pin specified in CONFIG[1].PSEL. Action on pin is configured in CONFIG[1].POLARITY.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_OUT Task for writing to pin specified in CONFIG[1].PSEL. Action on pin is
configured in CONFIG[1].POLARITY.
Trigger 1 Trigger task

6.10.4.3 TASKS_OUT[2]
Address offset: 0x008
Task for writing to pin specified in CONFIG[2].PSEL. Action on pin is configured in CONFIG[2].POLARITY.

4413_417 v1.9 293

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_OUT Task for writing to pin specified in CONFIG[2].PSEL. Action on pin is
configured in CONFIG[2].POLARITY.
Trigger 1 Trigger task

6.10.4.4 TASKS_OUT[3]
Address offset: 0x00C
Task for writing to pin specified in CONFIG[3].PSEL. Action on pin is configured in CONFIG[3].POLARITY.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_OUT Task for writing to pin specified in CONFIG[3].PSEL. Action on pin is
configured in CONFIG[3].POLARITY.
Trigger 1 Trigger task

6.10.4.5 TASKS_OUT[4]
Address offset: 0x010
Task for writing to pin specified in CONFIG[4].PSEL. Action on pin is configured in CONFIG[4].POLARITY.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_OUT Task for writing to pin specified in CONFIG[4].PSEL. Action on pin is
configured in CONFIG[4].POLARITY.
Trigger 1 Trigger task

6.10.4.6 TASKS_OUT[5]
Address offset: 0x014
Task for writing to pin specified in CONFIG[5].PSEL. Action on pin is configured in CONFIG[5].POLARITY.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_OUT Task for writing to pin specified in CONFIG[5].PSEL. Action on pin is
configured in CONFIG[5].POLARITY.
Trigger 1 Trigger task

6.10.4.7 TASKS_OUT[6]
Address offset: 0x018
Task for writing to pin specified in CONFIG[6].PSEL. Action on pin is configured in CONFIG[6].POLARITY.

4413_417 v1.9 294

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_OUT Task for writing to pin specified in CONFIG[6].PSEL. Action on pin is
configured in CONFIG[6].POLARITY.
Trigger 1 Trigger task

6.10.4.8 TASKS_OUT[7]
Address offset: 0x01C
Task for writing to pin specified in CONFIG[7].PSEL. Action on pin is configured in CONFIG[7].POLARITY.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_OUT Task for writing to pin specified in CONFIG[7].PSEL. Action on pin is
configured in CONFIG[7].POLARITY.
Trigger 1 Trigger task

6.10.4.9 TASKS_SET[0]
Address offset: 0x030
Task for writing to pin specified in CONFIG[0].PSEL. Action on pin is to set it high.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_SET Task for writing to pin specified in CONFIG[0].PSEL. Action on pin is to set it
high.
Trigger 1 Trigger task

6.10.4.10 TASKS_SET[1]
Address offset: 0x034
Task for writing to pin specified in CONFIG[1].PSEL. Action on pin is to set it high.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_SET Task for writing to pin specified in CONFIG[1].PSEL. Action on pin is to set it
high.
Trigger 1 Trigger task

6.10.4.11 TASKS_SET[2]
Address offset: 0x038
Task for writing to pin specified in CONFIG[2].PSEL. Action on pin is to set it high.

4413_417 v1.9 295

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_SET Task for writing to pin specified in CONFIG[2].PSEL. Action on pin is to set it
high.
Trigger 1 Trigger task

6.10.4.12 TASKS_SET[3]
Address offset: 0x03C
Task for writing to pin specified in CONFIG[3].PSEL. Action on pin is to set it high.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_SET Task for writing to pin specified in CONFIG[3].PSEL. Action on pin is to set it
high.
Trigger 1 Trigger task

6.10.4.13 TASKS_SET[4]
Address offset: 0x040
Task for writing to pin specified in CONFIG[4].PSEL. Action on pin is to set it high.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_SET Task for writing to pin specified in CONFIG[4].PSEL. Action on pin is to set it
high.
Trigger 1 Trigger task

6.10.4.14 TASKS_SET[5]
Address offset: 0x044
Task for writing to pin specified in CONFIG[5].PSEL. Action on pin is to set it high.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_SET Task for writing to pin specified in CONFIG[5].PSEL. Action on pin is to set it
high.
Trigger 1 Trigger task

6.10.4.15 TASKS_SET[6]
Address offset: 0x048
Task for writing to pin specified in CONFIG[6].PSEL. Action on pin is to set it high.

4413_417 v1.9 296

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_SET Task for writing to pin specified in CONFIG[6].PSEL. Action on pin is to set it
high.
Trigger 1 Trigger task

6.10.4.16 TASKS_SET[7]
Address offset: 0x04C
Task for writing to pin specified in CONFIG[7].PSEL. Action on pin is to set it high.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_SET Task for writing to pin specified in CONFIG[7].PSEL. Action on pin is to set it
high.
Trigger 1 Trigger task

6.10.4.17 TASKS_CLR[0]
Address offset: 0x060
Task for writing to pin specified in CONFIG[0].PSEL. Action on pin is to set it low.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_CLR Task for writing to pin specified in CONFIG[0].PSEL. Action on pin is to set it
low.
Trigger 1 Trigger task

6.10.4.18 TASKS_CLR[1]
Address offset: 0x064
Task for writing to pin specified in CONFIG[1].PSEL. Action on pin is to set it low.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_CLR Task for writing to pin specified in CONFIG[1].PSEL. Action on pin is to set it
low.
Trigger 1 Trigger task

6.10.4.19 TASKS_CLR[2]
Address offset: 0x068
Task for writing to pin specified in CONFIG[2].PSEL. Action on pin is to set it low.

4413_417 v1.9 297

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_CLR Task for writing to pin specified in CONFIG[2].PSEL. Action on pin is to set it
low.
Trigger 1 Trigger task

6.10.4.20 TASKS_CLR[3]
Address offset: 0x06C
Task for writing to pin specified in CONFIG[3].PSEL. Action on pin is to set it low.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_CLR Task for writing to pin specified in CONFIG[3].PSEL. Action on pin is to set it
low.
Trigger 1 Trigger task

6.10.4.21 TASKS_CLR[4]
Address offset: 0x070
Task for writing to pin specified in CONFIG[4].PSEL. Action on pin is to set it low.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_CLR Task for writing to pin specified in CONFIG[4].PSEL. Action on pin is to set it
low.
Trigger 1 Trigger task

6.10.4.22 TASKS_CLR[5]
Address offset: 0x074
Task for writing to pin specified in CONFIG[5].PSEL. Action on pin is to set it low.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_CLR Task for writing to pin specified in CONFIG[5].PSEL. Action on pin is to set it
low.
Trigger 1 Trigger task

6.10.4.23 TASKS_CLR[6]
Address offset: 0x078
Task for writing to pin specified in CONFIG[6].PSEL. Action on pin is to set it low.

4413_417 v1.9 298

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_CLR Task for writing to pin specified in CONFIG[6].PSEL. Action on pin is to set it
low.
Trigger 1 Trigger task

6.10.4.24 TASKS_CLR[7]
Address offset: 0x07C
Task for writing to pin specified in CONFIG[7].PSEL. Action on pin is to set it low.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_CLR Task for writing to pin specified in CONFIG[7].PSEL. Action on pin is to set it
low.
Trigger 1 Trigger task

6.10.4.25 EVENTS_IN[0]
Address offset: 0x100
Event generated from pin specified in CONFIG[0].PSEL

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_IN Event generated from pin specified in CONFIG[0].PSEL
NotGenerated 0 Event not generated
Generated 1 Event generated

6.10.4.26 EVENTS_IN[1]
Address offset: 0x104
Event generated from pin specified in CONFIG[1].PSEL

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_IN Event generated from pin specified in CONFIG[1].PSEL
NotGenerated 0 Event not generated
Generated 1 Event generated

6.10.4.27 EVENTS_IN[2]
Address offset: 0x108
Event generated from pin specified in CONFIG[2].PSEL

4413_417 v1.9 299

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_IN Event generated from pin specified in CONFIG[2].PSEL
NotGenerated 0 Event not generated
Generated 1 Event generated

6.10.4.28 EVENTS_IN[3]
Address offset: 0x10C
Event generated from pin specified in CONFIG[3].PSEL

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_IN Event generated from pin specified in CONFIG[3].PSEL
NotGenerated 0 Event not generated
Generated 1 Event generated

6.10.4.29 EVENTS_IN[4]
Address offset: 0x110
Event generated from pin specified in CONFIG[4].PSEL

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_IN Event generated from pin specified in CONFIG[4].PSEL
NotGenerated 0 Event not generated
Generated 1 Event generated

6.10.4.30 EVENTS_IN[5]
Address offset: 0x114
Event generated from pin specified in CONFIG[5].PSEL

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_IN Event generated from pin specified in CONFIG[5].PSEL
NotGenerated 0 Event not generated
Generated 1 Event generated

6.10.4.31 EVENTS_IN[6]
Address offset: 0x118
Event generated from pin specified in CONFIG[6].PSEL

4413_417 v1.9 300

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_IN Event generated from pin specified in CONFIG[6].PSEL
NotGenerated 0 Event not generated
Generated 1 Event generated

6.10.4.32 EVENTS_IN[7]
Address offset: 0x11C
Event generated from pin specified in CONFIG[7].PSEL

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_IN Event generated from pin specified in CONFIG[7].PSEL
NotGenerated 0 Event not generated
Generated 1 Event generated

6.10.4.33 EVENTS_PORT
Address offset: 0x17C
Event generated from multiple input GPIO pins with SENSE mechanism enabled

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_PORT Event generated from multiple input GPIO pins with SENSE mechanism
enabled
NotGenerated 0 Event not generated
Generated 1 Event generated

6.10.4.34 INTENSET
Address offset: 0x304
Enable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW IN[0] Write '1' to enable interrupt for event IN[0]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW IN[1] Write '1' to enable interrupt for event IN[1]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

4413_417 v1.9 301

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
C RW IN[2] Write '1' to enable interrupt for event IN[2]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
D RW IN[3] Write '1' to enable interrupt for event IN[3]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
E RW IN[4] Write '1' to enable interrupt for event IN[4]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
F RW IN[5] Write '1' to enable interrupt for event IN[5]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
G RW IN[6] Write '1' to enable interrupt for event IN[6]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
H RW IN[7] Write '1' to enable interrupt for event IN[7]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
I RW PORT Write '1' to enable interrupt for event PORT
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.10.4.35 INTENCLR
Address offset: 0x308
Disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW IN[0] Write '1' to disable interrupt for event IN[0]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW IN[1] Write '1' to disable interrupt for event IN[1]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW IN[2] Write '1' to disable interrupt for event IN[2]
Clear 1 Disable
Disabled 0 Read: Disabled

4413_417 v1.9 302

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Enabled 1 Read: Enabled
D RW IN[3] Write '1' to disable interrupt for event IN[3]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
E RW IN[4] Write '1' to disable interrupt for event IN[4]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
F RW IN[5] Write '1' to disable interrupt for event IN[5]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
G RW IN[6] Write '1' to disable interrupt for event IN[6]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
H RW IN[7] Write '1' to disable interrupt for event IN[7]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
I RW PORT Write '1' to disable interrupt for event PORT
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.10.4.36 CONFIG[0]
Address offset: 0x510
Configuration for OUT[n], SET[n], and CLR[n] tasks and IN[n] event

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E D D C B B B B B A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW MODE Mode
Disabled 0 Disabled. Pin specified by PSEL will not be acquired by the GPIOTE module.
Event 1 Event mode

The pin specified by PSEL will be configured as an input and the IN[n] event
will be generated if operation specified in POLARITY occurs on the pin.
Task 3 Task mode

The GPIO specified by PSEL will be configured as an output and triggering

the SET[n], CLR[n] or OUT[n] task will perform the operation specified
by POLARITY on the pin. When enabled as a task the GPIOTE module will
acquire the pin and the pin can no longer be written as a regular output pin
from the GPIO module.
B RW PSEL [0..31] GPIO number associated with SET[n], CLR[n], and OUT[n] tasks and IN[n]
event
C RW PORT [0..1] Port number

4413_417 v1.9 303

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E D D C B B B B B A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
D RW POLARITY When In task mode: Operation to be performed on output when OUT[n]
task is triggered. When In event mode: Operation on input that shall trigger
IN[n] event.
None 0 Task mode: No effect on pin from OUT[n] task. Event mode: no IN[n] event
generated on pin activity.
LoToHi 1 Task mode: Set pin from OUT[n] task. Event mode: Generate IN[n] event
when rising edge on pin.
HiToLo 2 Task mode: Clear pin from OUT[n] task. Event mode: Generate IN[n] event
when falling edge on pin.
Toggle 3 Task mode: Toggle pin from OUT[n]. Event mode: Generate IN[n] when any
change on pin.
E RW OUTINIT When in task mode: Initial value of the output when the GPIOTE channel is
configured. When in event mode: No effect.
Low 0 Task mode: Initial value of pin before task triggering is low
High 1 Task mode: Initial value of pin before task triggering is high

6.10.4.37 CONFIG[1]
Address offset: 0x514
Configuration for OUT[n], SET[n], and CLR[n] tasks and IN[n] event

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E D D C B B B B B A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW MODE Mode
Disabled 0 Disabled. Pin specified by PSEL will not be acquired by the GPIOTE module.
Event 1 Event mode

The pin specified by PSEL will be configured as an input and the IN[n] event
will be generated if operation specified in POLARITY occurs on the pin.
Task 3 Task mode

The GPIO specified by PSEL will be configured as an output and triggering

the SET[n], CLR[n] or OUT[n] task will perform the operation specified
by POLARITY on the pin. When enabled as a task the GPIOTE module will
acquire the pin and the pin can no longer be written as a regular output pin
from the GPIO module.
B RW PSEL [0..31] GPIO number associated with SET[n], CLR[n], and OUT[n] tasks and IN[n]
event
C RW PORT [0..1] Port number
D RW POLARITY When In task mode: Operation to be performed on output when OUT[n]
task is triggered. When In event mode: Operation on input that shall trigger
IN[n] event.
None 0 Task mode: No effect on pin from OUT[n] task. Event mode: no IN[n] event
generated on pin activity.
LoToHi 1 Task mode: Set pin from OUT[n] task. Event mode: Generate IN[n] event
when rising edge on pin.
HiToLo 2 Task mode: Clear pin from OUT[n] task. Event mode: Generate IN[n] event
when falling edge on pin.

4413_417 v1.9 304

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E D D C B B B B B A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Toggle 3 Task mode: Toggle pin from OUT[n]. Event mode: Generate IN[n] when any
change on pin.
E RW OUTINIT When in task mode: Initial value of the output when the GPIOTE channel is
configured. When in event mode: No effect.
Low 0 Task mode: Initial value of pin before task triggering is low
High 1 Task mode: Initial value of pin before task triggering is high

6.10.4.38 CONFIG[2]
Address offset: 0x518
Configuration for OUT[n], SET[n], and CLR[n] tasks and IN[n] event

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E D D C B B B B B A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW MODE Mode
Disabled 0 Disabled. Pin specified by PSEL will not be acquired by the GPIOTE module.
Event 1 Event mode

The pin specified by PSEL will be configured as an input and the IN[n] event
will be generated if operation specified in POLARITY occurs on the pin.
Task 3 Task mode

The GPIO specified by PSEL will be configured as an output and triggering

the SET[n], CLR[n] or OUT[n] task will perform the operation specified
by POLARITY on the pin. When enabled as a task the GPIOTE module will
acquire the pin and the pin can no longer be written as a regular output pin
from the GPIO module.
B RW PSEL [0..31] GPIO number associated with SET[n], CLR[n], and OUT[n] tasks and IN[n]
event
C RW PORT [0..1] Port number
D RW POLARITY When In task mode: Operation to be performed on output when OUT[n]
task is triggered. When In event mode: Operation on input that shall trigger
IN[n] event.
None 0 Task mode: No effect on pin from OUT[n] task. Event mode: no IN[n] event
generated on pin activity.
LoToHi 1 Task mode: Set pin from OUT[n] task. Event mode: Generate IN[n] event
when rising edge on pin.
HiToLo 2 Task mode: Clear pin from OUT[n] task. Event mode: Generate IN[n] event
when falling edge on pin.
Toggle 3 Task mode: Toggle pin from OUT[n]. Event mode: Generate IN[n] when any
change on pin.
E RW OUTINIT When in task mode: Initial value of the output when the GPIOTE channel is
configured. When in event mode: No effect.
Low 0 Task mode: Initial value of pin before task triggering is low
High 1 Task mode: Initial value of pin before task triggering is high

6.10.4.39 CONFIG[3]
Address offset: 0x51C

4413_417 v1.9 305

 Peripherals

Configuration for OUT[n], SET[n], and CLR[n] tasks and IN[n] event

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E D D C B B B B B A A
Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW MODE Mode
Disabled 0 Disabled. Pin specified by PSEL will not be acquired by the GPIOTE module.
Event 1 Event mode

The pin specified by PSEL will be configured as an input and the IN[n] event
will be generated if operation specified in POLARITY occurs on the pin.
Task 3 Task mode

The GPIO specified by PSEL will be configured as an output and triggering

the SET[n], CLR[n] or OUT[n] task will perform the operation specified
by POLARITY on the pin. When enabled as a task the GPIOTE module will
acquire the pin and the pin can no longer be written as a regular output pin
from the GPIO module.
B RW PSEL [0..31] GPIO number associated with SET[n], CLR[n], and OUT[n] tasks and IN[n]
event
C RW PORT [0..1] Port number
D RW POLARITY When In task mode: Operation to be performed on output when OUT[n]
task is triggered. When In event mode: Operation on input that shall trigger
IN[n] event.
None 0 Task mode: No effect on pin from OUT[n] task. Event mode: no IN[n] event
generated on pin activity.
LoToHi 1 Task mode: Set pin from OUT[n] task. Event mode: Generate IN[n] event
when rising edge on pin.
HiToLo 2 Task mode: Clear pin from OUT[n] task. Event mode: Generate IN[n] event
when falling edge on pin.
Toggle 3 Task mode: Toggle pin from OUT[n]. Event mode: Generate IN[n] when any
change on pin.
E RW OUTINIT When in task mode: Initial value of the output when the GPIOTE channel is
configured. When in event mode: No effect.
Low 0 Task mode: Initial value of pin before task triggering is low
High 1 Task mode: Initial value of pin before task triggering is high

6.10.4.40 CONFIG[4]
Address offset: 0x520
Configuration for OUT[n], SET[n], and CLR[n] tasks and IN[n] event

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E D D C B B B B B A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW MODE Mode
Disabled 0 Disabled. Pin specified by PSEL will not be acquired by the GPIOTE module.
Event 1 Event mode

The pin specified by PSEL will be configured as an input and the IN[n] event
will be generated if operation specified in POLARITY occurs on the pin.

4413_417 v1.9 306

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E D D C B B B B B A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Task 3 Task mode

The GPIO specified by PSEL will be configured as an output and triggering

the SET[n], CLR[n] or OUT[n] task will perform the operation specified
by POLARITY on the pin. When enabled as a task the GPIOTE module will
acquire the pin and the pin can no longer be written as a regular output pin
from the GPIO module.
B RW PSEL [0..31] GPIO number associated with SET[n], CLR[n], and OUT[n] tasks and IN[n]
event
C RW PORT [0..1] Port number
D RW POLARITY When In task mode: Operation to be performed on output when OUT[n]
task is triggered. When In event mode: Operation on input that shall trigger
IN[n] event.
None 0 Task mode: No effect on pin from OUT[n] task. Event mode: no IN[n] event
generated on pin activity.
LoToHi 1 Task mode: Set pin from OUT[n] task. Event mode: Generate IN[n] event
when rising edge on pin.
HiToLo 2 Task mode: Clear pin from OUT[n] task. Event mode: Generate IN[n] event
when falling edge on pin.
Toggle 3 Task mode: Toggle pin from OUT[n]. Event mode: Generate IN[n] when any
change on pin.
E RW OUTINIT When in task mode: Initial value of the output when the GPIOTE channel is
configured. When in event mode: No effect.
Low 0 Task mode: Initial value of pin before task triggering is low
High 1 Task mode: Initial value of pin before task triggering is high

6.10.4.41 CONFIG[5]
Address offset: 0x524
Configuration for OUT[n], SET[n], and CLR[n] tasks and IN[n] event

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E D D C B B B B B A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW MODE Mode
Disabled 0 Disabled. Pin specified by PSEL will not be acquired by the GPIOTE module.
Event 1 Event mode

The pin specified by PSEL will be configured as an input and the IN[n] event
will be generated if operation specified in POLARITY occurs on the pin.
Task 3 Task mode

The GPIO specified by PSEL will be configured as an output and triggering

the SET[n], CLR[n] or OUT[n] task will perform the operation specified
by POLARITY on the pin. When enabled as a task the GPIOTE module will
acquire the pin and the pin can no longer be written as a regular output pin
from the GPIO module.
B RW PSEL [0..31] GPIO number associated with SET[n], CLR[n], and OUT[n] tasks and IN[n]
event
C RW PORT [0..1] Port number

4413_417 v1.9 307

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E D D C B B B B B A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
D RW POLARITY When In task mode: Operation to be performed on output when OUT[n]
task is triggered. When In event mode: Operation on input that shall trigger
IN[n] event.
None 0 Task mode: No effect on pin from OUT[n] task. Event mode: no IN[n] event
generated on pin activity.
LoToHi 1 Task mode: Set pin from OUT[n] task. Event mode: Generate IN[n] event
when rising edge on pin.
HiToLo 2 Task mode: Clear pin from OUT[n] task. Event mode: Generate IN[n] event
when falling edge on pin.
Toggle 3 Task mode: Toggle pin from OUT[n]. Event mode: Generate IN[n] when any
change on pin.
E RW OUTINIT When in task mode: Initial value of the output when the GPIOTE channel is
configured. When in event mode: No effect.
Low 0 Task mode: Initial value of pin before task triggering is low
High 1 Task mode: Initial value of pin before task triggering is high

6.10.4.42 CONFIG[6]
Address offset: 0x528
Configuration for OUT[n], SET[n], and CLR[n] tasks and IN[n] event

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E D D C B B B B B A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW MODE Mode
Disabled 0 Disabled. Pin specified by PSEL will not be acquired by the GPIOTE module.
Event 1 Event mode

The pin specified by PSEL will be configured as an input and the IN[n] event
will be generated if operation specified in POLARITY occurs on the pin.
Task 3 Task mode

The GPIO specified by PSEL will be configured as an output and triggering

the SET[n], CLR[n] or OUT[n] task will perform the operation specified
by POLARITY on the pin. When enabled as a task the GPIOTE module will
acquire the pin and the pin can no longer be written as a regular output pin
from the GPIO module.
B RW PSEL [0..31] GPIO number associated with SET[n], CLR[n], and OUT[n] tasks and IN[n]
event
C RW PORT [0..1] Port number
D RW POLARITY When In task mode: Operation to be performed on output when OUT[n]
task is triggered. When In event mode: Operation on input that shall trigger
IN[n] event.
None 0 Task mode: No effect on pin from OUT[n] task. Event mode: no IN[n] event
generated on pin activity.
LoToHi 1 Task mode: Set pin from OUT[n] task. Event mode: Generate IN[n] event
when rising edge on pin.
HiToLo 2 Task mode: Clear pin from OUT[n] task. Event mode: Generate IN[n] event
when falling edge on pin.

4413_417 v1.9 308

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E D D C B B B B B A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Toggle 3 Task mode: Toggle pin from OUT[n]. Event mode: Generate IN[n] when any
change on pin.
E RW OUTINIT When in task mode: Initial value of the output when the GPIOTE channel is
configured. When in event mode: No effect.
Low 0 Task mode: Initial value of pin before task triggering is low
High 1 Task mode: Initial value of pin before task triggering is high

6.10.4.43 CONFIG[7]
Address offset: 0x52C
Configuration for OUT[n], SET[n], and CLR[n] tasks and IN[n] event

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E D D C B B B B B A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW MODE Mode
Disabled 0 Disabled. Pin specified by PSEL will not be acquired by the GPIOTE module.
Event 1 Event mode

The pin specified by PSEL will be configured as an input and the IN[n] event
will be generated if operation specified in POLARITY occurs on the pin.
Task 3 Task mode

The GPIO specified by PSEL will be configured as an output and triggering

the SET[n], CLR[n] or OUT[n] task will perform the operation specified
by POLARITY on the pin. When enabled as a task the GPIOTE module will
acquire the pin and the pin can no longer be written as a regular output pin
from the GPIO module.
B RW PSEL [0..31] GPIO number associated with SET[n], CLR[n], and OUT[n] tasks and IN[n]
event
C RW PORT [0..1] Port number
D RW POLARITY When In task mode: Operation to be performed on output when OUT[n]
task is triggered. When In event mode: Operation on input that shall trigger
IN[n] event.
None 0 Task mode: No effect on pin from OUT[n] task. Event mode: no IN[n] event
generated on pin activity.
LoToHi 1 Task mode: Set pin from OUT[n] task. Event mode: Generate IN[n] event
when rising edge on pin.
HiToLo 2 Task mode: Clear pin from OUT[n] task. Event mode: Generate IN[n] event
when falling edge on pin.
Toggle 3 Task mode: Toggle pin from OUT[n]. Event mode: Generate IN[n] when any
change on pin.
E RW OUTINIT When in task mode: Initial value of the output when the GPIOTE channel is
configured. When in event mode: No effect.
Low 0 Task mode: Initial value of pin before task triggering is low
High 1 Task mode: Initial value of pin before task triggering is high

4413_417 v1.9 309

 Peripherals

6.11 I2S — Inter-IC sound interface

The I2S (Inter-IC Sound) module, supports the original two-channel I2S format, and left or right-aligned
formats. It implements EasyDMA for sample transfer directly to and from RAM without CPU intervention.
The I2S peripheral has the following main features:
• Master and Slave mode
• Simultaneous bi-directional (TX and RX) audio streaming
• Original I2S and left- or right-aligned format
• 8, 16 and 24-bit sample width
• Low-jitter Master Clock generator
• Various sample rates

PSEL.MCK PSEL.LRCK PSEL.SCK PSEL.SDIN PSEL.SDOUT

I2S

CONFIG.MCKEN
Master clock MCK
generator
CONFIG.MCKFREQ

CONFIG.RATIO Div Div CONFIG.FORMAT

CONFIG.MODE

SDOUT
SDIN
LRCK

SCK

CONFIG.ALIGN Serial tranceiever

TXD.PTR
RXD.PTR EasyDMA
RXTXD.MAXCNT

RAM

Figure 47: I2S master

6.11.1 Mode
The I2S protocol specification defines two modes of operation, Master and Slave.
The I2S mode decides which of the two sides (Master or Slave) shall provide the clock signals LRCK and
SCK, and these signals are always supplied by the Master to the Slave.

6.11.2 Transmitting and receiving

The I2S module supports both transmission (TX) and reception (RX) of serial data. In both cases the serial
data is shifted synchronously to the clock signals SCK and LRCK.
TX data is written to the SDOUT pin on the falling edge of SCK, and RX data is read from the SDIN pin on
the rising edge of SCK. The most significant bit (MSB) is always transmitted first.

4413_417 v1.9 310

 Peripherals

TX and RX are available in both Master and Slave modes and can be enabled/disabled independently in
the CONFIG.TXEN on page 323 and CONFIG.RXEN on page 323.
Transmission and/or reception is started by triggering the START task. When started and transmission
is enabled (in CONFIG.TXEN on page 323), the TXPTRUPD event will be generated for every
RXTXD.MAXCNT on page 326 number of transmitted data words (containing one or more samples).
Similarly, when started and reception is enabled (in CONFIG.RXEN on page 323), the RXPTRUPD event
will be generated for every RXTXD.MAXCNT on page 326 received data words.
RXTXD.MAXCNT RXTXD.MAXCNT

Left 0 Right 0 Left 1 RIght 1 Left 2 Right 2 Left 3 Right 3 Left 4

SDOUT

A A A A C C C C E
SDIN

B B B B D D D D F
SCK
LRCK

RXPTRUPD

RXPTRUPD

RXPTRUPD
TXPTRUPD

TXPTRUPD
TXPTRUPD
CPU

RXD.PTR = D

TXD.PTR = E

RXD.PTR = F

TXD.PTR = G

RXD.PTR = H
TXD.PTR = C
TXD.PTR = A
RXD.PTR = B
START

Figure 48: Transmitting and receiving. CONFIG.FORMAT = Aligned,

CONFIG.SWIDTH = 8Bit, CONFIG.CHANNELS = Stereo, RXTXD.MAXCNT = 1.

6.11.3 Left right clock (LRCK)

The Left Right Clock (LRCK), often referred to as "word clock", "sample clock" or "word select" in I2S
context, is the clock defining the frames in the serial bit streams sent and received on SDOUT and SDIN,
respectively.
In I2S mode, each frame contains one left and right sample pair, with the left sample being transferred
during the low half period of LRCK followed by the right sample being transferred during the high period of
LRCK.
In Aligned mode, each frame contains one left and right sample pair, with the left sample being
transferred during the high half period of LRCK followed by the right sample being transferred during the
low period of LRCK.
Consequently, the LRCK frequency is equivalent to the audio sample rate.
When operating in Master mode, the LRCK is generated from the MCK, and the frequency of LRCK is then
given as:

LRCK = MCK / CONFIG.RATIO

LRCK always toggles around the falling edge of the serial clock SCK.

6.11.4 Serial clock (SCK)

The serial clock (SCK), often referred to as the serial bit clock, pulses once for each data bit being
transferred on the serial data lines SDIN and SDOUT.

4413_417 v1.9 311

 Peripherals

When operating in Master mode the SCK is generated from the MCK, and the frequency of SCK is then
given as:

SCK = 2 * LRCK * CONFIG.SWIDTH

The falling edge of the SCK falls on the toggling edge of LRCK.
When operating in Slave mode SCK is provided by the external I2S master.

6.11.5 Master clock (MCK)

The master clock (MCK) is the clock from which LRCK and SCK are derived when operating in Master mode.
The MCK is generated by an internal MCK generator. This generator always needs to be enabled when in
Master mode, but the generator can also be enabled when in Slave mode. Enabling the generator when
in slave mode can be useful in the case where the external Master is not able to generate its own master
clock.
The MCK generator is enabled/disabled in the register CONFIG.MCKEN on page 323, and the generator
is started or stopped by the START or STOP tasks.
In Master mode the LRCK and the SCK frequencies are closely related, as both are derived from MCK and
set indirectly through CONFIG.RATIO on page 324 and CONFIG.SWIDTH on page 325.
When configuring these registers, the user is responsible for fulfilling the following requirements:
1. SCK frequency can never exceed the MCK frequency, which can be formulated as:

CONFIG.RATIO >= 2 * CONFIG.SWIDTH

2. The MCK/LRCK ratio shall be a multiple of 2 * CONFIG.SWIDTH, which can be formulated as:

Integer = (CONFIG.RATIO / (2 * CONFIG.SWIDTH))

The MCK signal can be routed to an output pin (specified in PSEL.MCK) to supply external I2S devices that
require the MCK to be supplied from the outside.
When operating in Slave mode, the I2S module does not use the MCK and the MCK generator does not
need to be enabled.
MCK
MCK
RATIO =
LRCK
LRCK
SWIDTH

SCK

Figure 49: Relation between RATIO, MCK and LRCK.

4413_417 v1.9 312

 Peripherals

Desired LRCK CONFIG.SWIDTH

CONFIG.RATIO CONFIG.MCKFREQ
MCK [Hz] LRCK [Hz] LRCK error
[Hz] [%]
16000 16Bit 32X 32MDIV63 507936.5 15873.0 -0.8
16000 16Bit 64X 32MDIV31 1032258.1 16129.0 0.8
16000 16Bit 256X 32MDIV8 4000000.0 15625.0 -2.3
32000 16Bit 32X 32MDIV31 1032258.1 32258.1 0.8
32000 16Bit 64X 32MDIV16 2000000.0 31250.0 -2.3
44100 16Bit 32X 32MDIV23 1391304.3 43478.3 -1.4
44100 16Bit 64X 32MDIV11 2909090.9 45454.5 3.1

Table 21: Configuration examples

6.11.6 Width, alignment and format

The CONFIG.SWIDTH register primarily defines the sample width of the data written to memory. In master
mode, it then also sets the amount of bits per frame. In Slave mode it controls padding/trimming if
required. Left, right, transmitted, and received samples always have the same width. The CONFIG.FORMAT
register specifies the position of the data frames with respect to the LRCK edges in both Master and Slave
modes.
When using I2S format, the first bit in a half-frame (containing one left or right sample) gets sampled on
the second rising edge of the SCK after a LRCK edge. When using Aligned mode, the first bit in a half-frame
gets sampled on the first rising edge of SCK following a LRCK edge.
For data being received on SDIN the sample value can be either right or left-aligned inside a half-frame, as
specified in CONFIG.ALIGN on page 325. CONFIG.ALIGN on page 325 affects only the decoding of the
incoming samples (SDIN), while the outgoing samples (SDOUT) are always left-aligned (or justified).
When using left-alignment, each half-frame starts with the MSB of the sample value (both for data being
sent on SDOUT and received on SDIN).
When using right-alignment, each half-frame of data being received on SDIN ends with the LSB of the
sample value, while each half-frame of data being sent on SDOUT starts with the MSB of the sample value
(same as for left-alignment).
In Master mode, the size of a half-frame (in number of SCK periods) equals the sample width (in number
of bits), and in this case the alignment setting does not care as each half-frame in any case will start with
the MSB and end with the LSB of the sample value.
In slave mode, however, the sample width does not need to equal the frame size. This means you might
have extra or fewer SCK pulses per half-frame than what the sample width specified in CONFIG.SWIDTH
requires.
In the case where we use left-alignment and the number of SCK pulses per half-frame is higher than the
sample width, the following will apply:
• For data received on SDIN, all bits after the LSB of the sample value will be discarded.
• For data sent on SDOUT, all bits after the LSB of the sample value will be 0.
In the case where we use left-alignment and the number of SCK pulses per frame is lower than the
sample width, the following will apply:
• Data sent and received on SDOUT and SDIN will be truncated with the LSBs being removed first.
In the case where we use right-alignment and the number of SCK pulses per frame is higher than the
sample width, the following will apply:

4413_417 v1.9 313

 Peripherals

• For data received on SDIN, all bits before the MSB of the sample value will be discarded.
• For data sent on SDOUT, all bits after the LSB of the sample value will be 0 (same behavior as for left-
alignment).
In the case where we use right-alignment and the number of SCK pulses per frame is lower than the
sample width, the following will apply:
• Data received on SDIN will be sign-extended to "sample width" number of bits before being written to
memory.
• Data sent on SDOUT will be truncated with the LSBs being removed first (same behavior as for left-
alignment).
frame
LRCK left right left
SCK
SDIN or SDOUT

Figure 50: I2S format. CONFIG.SWIDTH equalling half-frame size.

frame
LRCK left right left
SCK
SDATA

Figure 51: Aligned format. CONFIG.SWIDTH equalling half-frame size.

6.11.7 EasyDMA
The I2S module implements EasyDMA for accessing internal Data RAM without CPU intervention.
The source and destination pointers for the TX and RX data are configured in TXD.PTR on page 326 and
RXD.PTR on page 326. The memory pointed to by these pointers will only be read or written when TX or
RX are enabled in CONFIG.TXEN on page 323 and CONFIG.RXEN on page 323.
The addresses written to the pointer registers TXD.PTR on page 326 and RXD.PTR on page 326 are
double-buffered in hardware, and these double buffers are updated for every RXTXD.MAXCNT on page
326 words (containing one or more samples) read/written from/to memory. The events TXPTRUPD and
RXPTRUPD are generated whenever the TXD.PTR and RXD.PTR are transferred to these double buffers.
If TXD.PTR on page 326 is not pointing to the Data RAM region when transmission is enabled, or
RXD.PTR on page 326 is not pointing to the Data RAM region when reception is enabled, an EasyDMA
transfer may result in a HardFault and/or memory corruption. See Memory on page 21 for more
information about the different memory regions.
Due to the nature of I2S, where the number of transmitted samples always equals the number of received
samples (at least when both TX and RX are enabled), one common register RXTXD.MAXCNT on page
326 is used for specifying the sizes of these two memory buffers. The size of the buffers is specified in
a number of 32-bit words. Such a 32-bit memory word can either contain four 8-bit samples, two 16-bit
samples or one right-aligned 24-bit sample sign extended to 32 bit.
In stereo mode (CONFIG.CHANNELS=Stereo), the samples are stored as "left and right sample pairs" in
memory. Figure Memory mapping for 8 bit stereo. CONFIG.SWIDTH = 8Bit, CONFIG.CHANNELS = Stereo.
on page 315, Memory mapping for 16 bit stereo. CONFIG.SWIDTH = 16Bit, CONFIG.CHANNELS = Stereo.
on page 315 and Memory mapping for 24 bit stereo. CONFIG.SWIDTH = 24Bit, CONFIG.CHANNELS =
Stereo. on page 316 show how the samples are mapped to memory in this mode. The mapping is valid
for both RX and TX.
In mono mode (CONFIG.CHANNELS=Left or Right), RX sample from only one channel in the frame is
stored in memory, the other channel sample is ignored. Illustrations Memory mapping for 8 bit mono.
CONFIG.SWIDTH = 8Bit, CONFIG.CHANNELS = Left. on page 315, Memory mapping for 16 bit mono, left

4413_417 v1.9 314

 Peripherals

channel only. CONFIG.SWIDTH = 16Bit, CONFIG.CHANNELS = Left. on page 315 and Memory mapping
for 24 bit mono, left channel only. CONFIG.SWIDTH = 24Bit, CONFIG.CHANNELS = Left. on page 316
show how RX samples are mapped to memory in this mode.
For TX, the same outgoing sample read from memory is transmitted on both left and right in a frame,
resulting in a mono output stream.

31 24 23 16 15 8 7 0

x.PTR Right sample 1 Left sample 1 Right sample 0 Left sample 0

x.PTR + 4 Right sample 3 Left sample 3 Right sample 2 Left sample 2

Right sample Left sample Right sample Left sample

x.PTR + (n*2) - 4 n-1 n-1 n-2 n-2

Figure 52: Memory mapping for 8 bit stereo. CONFIG.SWIDTH = 8Bit, CONFIG.CHANNELS = Stereo.

31 24 23 16 15 8 7 0

x.PTR Left sample 3 Left sample 2 Left sample 1 Left sample 0

x.PTR + 4 Left sample 7 Left sample 6 Left sample 5 Left sample 4

Left sample Left sample Left sample Left sample

x.PTR + n - 4 n-1 n-2 n-3 n-4

Figure 53: Memory mapping for 8 bit mono. CONFIG.SWIDTH = 8Bit, CONFIG.CHANNELS = Left.

31 16 15 0

x.PTR Right sample 0 Left sample 0

x.PTR + 4 Right sample 1 Left sample 1

x.PTR + (n*4) - 4 Right sample n - 1 Left sample n - 1

Figure 54: Memory mapping for 16 bit stereo. CONFIG.SWIDTH = 16Bit, CONFIG.CHANNELS = Stereo.

31 16 15 0

x.PTR Left sample 1 Left sample 0

x.PTR + 4 Left sample 3 Left sample 2

x.PTR + (n*2) - 4 Left sample n - 1 Left sample n - 2

Figure 55: Memory mapping for 16 bit mono, left channel

only. CONFIG.SWIDTH = 16Bit, CONFIG.CHANNELS = Left.

4413_417 v1.9 315

 Peripherals

31 23 0

x.PTR Sign ext. Left sample 0

x.PTR + 4 Sign ext. Right sample 0

x.PTR + (n*8) - 8 Sign ext. Left sample n - 1

x.PTR + (n*8) - 4 Sign ext. Right sample n - 1

Figure 56: Memory mapping for 24 bit stereo. CONFIG.SWIDTH = 24Bit, CONFIG.CHANNELS = Stereo.

31 23 0

x.PTR Sign ext. Left sample 0

x.PTR + 4 Sign ext. Left sample 1

x.PTR + (n*4) - 4 Sign ext. Left sample n - 1

Figure 57: Memory mapping for 24 bit mono, left channel

only. CONFIG.SWIDTH = 24Bit, CONFIG.CHANNELS = Left.

6.11.8 Module operation

Described here is a typical operating procedure for the I2S module.

4413_417 v1.9 316

 Peripherals

1. Configure the I2S module using the CONFIG registers

// Enable reception
NRF_I2S->CONFIG.RXEN = (I2S_CONFIG_RXEN_RXEN_Enabled <<
I2S_CONFIG_RXEN_RXEN_Pos);
// Enable transmission
NRF_I2S->CONFIG.TXEN = (I2S_CONFIG_TXEN_TXEN_Enabled <<
I2S_CONFIG_TXEN_TXEN_Pos);
// Enable MCK generator
NRF_I2S->CONFIG.MCKEN = (I2S_CONFIG_MCKEN_MCKEN_Enabled <<
I2S_CONFIG_MCKEN_MCKEN_Pos);
// MCKFREQ = 4 MHz
NRF_I2S->CONFIG.MCKFREQ = I2S_CONFIG_MCKFREQ_MCKFREQ_32MDIV8 <<
I2S_CONFIG_MCKFREQ_MCKFREQ_Pos;
// Ratio = 256
NRF_I2S->CONFIG.RATIO = I2S_CONFIG_RATIO_RATIO_256X <<
I2S_CONFIG_RATIO_RATIO_Pos;
// MCKFREQ = 4 MHz and Ratio = 256 gives sample rate = 15.625 ks/s
// Sample width = 16 bit
NRF_I2S->CONFIG.SWIDTH = I2S_CONFIG_SWIDTH_SWIDTH_16Bit <<
I2S_CONFIG_SWIDTH_SWIDTH_Pos;
// Alignment = Left
NRF_I2S->CONFIG.ALIGN = I2S_CONFIG_ALIGN_ALIGN_Left <<
I2S_CONFIG_ALIGN_ALIGN_Pos;
// Format = I2S
NRF_I2S->CONFIG.FORMAT = I2S_CONFIG_FORMAT_FORMAT_I2S <<
I2S_CONFIG_FORMAT_FORMAT_Pos;
// Use stereo
NRF_I2S->CONFIG.CHANNELS = I2S_CONFIG_CHANNELS_CHANNELS_Stereo <<
I2S_CONFIG_CHANNELS_CHANNELS_Pos;

2. Map IO pins using the PINSEL registers

// MCK routed to pin 0

NRF_I2S->PSEL.MCK = (0 << I2S_PSEL_MCK_PIN_Pos) |
(I2S_PSEL_MCK_CONNECT_Connected <<
I2S_PSEL_MCK_CONNECT_Pos);
// SCK routed to pin 1
NRF_I2S->PSEL.SCK = (1 << I2S_PSEL_SCK_PIN_Pos) |
(I2S_PSEL_SCK_CONNECT_Connected <<
I2S_PSEL_SCK_CONNECT_Pos);
// LRCK routed to pin 2
NRF_I2S->PSEL.LRCK = (2 << I2S_PSEL_LRCK_PIN_Pos) |
(I2S_PSEL_LRCK_CONNECT_Connected <<
I2S_PSEL_LRCK_CONNECT_Pos);
// SDOUT routed to pin 3
NRF_I2S->PSEL.SDOUT = (3 << I2S_PSEL_SDOUT_PIN_Pos) |
(I2S_PSEL_SDOUT_CONNECT_Connected <<
I2S_PSEL_SDOUT_CONNECT_Pos);
// SDIN routed on pin 4
NRF_I2S->PSEL.SDIN = (4 << I2S_PSEL_SDIN_PIN_Pos) |
(I2S_PSEL_SDIN_CONNECT_Connected <<
I2S_PSEL_SDIN_CONNECT_Pos);

4413_417 v1.9 317

 Peripherals

3. Configure TX and RX data pointers using the TXD, RXD and RXTXD registers

NRF_I2S->TXD.PTR = my_tx_buf;
NRF_I2S->RXD.PTR = my_rx_buf;
NRF_I2S->TXD.MAXCNT = MY_BUF_SIZE;

4. Enable the I2S module using the ENABLE register

NRF_I2S->ENABLE = 1;

5. Start audio streaming using the START task

NRF_I2S->TASKS_START = 1;

6. Handle received and transmitted data when receiving the TXPTRUPD and RXPTRUPD events

if(NRF_I2S->EVENTS_TXPTRUPD != 0)
{
NRF_I2S->TXD.PTR = my_next_tx_buf;
NRF_I2S->EVENTS_TXPTRUPD = 0;
}

if(NRF_I2S->EVENTS_RXPTRUPD != 0)
{
NRF_I2S->RXD.PTR = my_next_rx_buf;
NRF_I2S->EVENTS_RXPTRUPD = 0;
}

6.11.9 Pin configuration

The MCK, SCK, LRCK, SDIN and SDOUT signals associated with the I2S module are mapped to physical pins
according to the pin numbers specified in the PSEL.x registers.
These pins are acquired whenever the I2S module is enabled through the register ENABLE on page 322.
When a pin is acquired by the I2S module, the direction of the pin (input or output) will be configured
automatically, and any pin direction setting done in the GPIO module will be overridden. The directions for
the various I2S pins are shown below in GPIO configuration before enabling peripheral (master mode) on
page 318 and GPIO configuration before enabling peripheral (slave mode) on page 319.
To secure correct signal levels on the pins when the system is in OFF mode, and when the I2S module is
disabled, these pins must be configured in the GPIO peripheral directly.

I2S signal I2S pin Direction Output value Comment

MCK As specified in PSEL.MCK Output 0
LRCK As specified in PSEL.LRCK Output 0
SCK As specified in PSEL.SCK Output 0
SDIN As specified in PSEL.SDIN Input Not applicable
SDOUT As specified in PSEL.SDOUT Output 0

Table 22: GPIO configuration before enabling peripheral (master mode)

4413_417 v1.9 318

 Peripherals

I2S signal I2S pin Direction Output value Comment

MCK As specified in PSEL.MCK Output 0
LRCK As specified in PSEL.LRCK Input Not applicable
SCK As specified in PSEL.SCK Input Not applicable
SDIN As specified in PSEL.SDIN Input Not applicable
SDOUT As specified in PSEL.SDOUT Output 0

Table 23: GPIO configuration before enabling peripheral (slave mode)

6.11.10 Registers
Instances

Instance Base address Description

I2S 0x40025000 Inter-IC sound interface

Register overview

Register Offset Description

TASKS_START 0x000 Starts continuous I2S transfer. Also starts MCK generator when this is enabled.
TASKS_STOP 0x004 Stops I2S transfer. Also stops MCK generator. Triggering this task will cause the STOPPED event to be
generated.
EVENTS_RXPTRUPD 0x104 The RXD.PTR register has been copied to internal double-buffers. When the I2S module is started
and RX is enabled, this event will be generated for every RXTXD.MAXCNT words that are received on
the SDIN pin.
EVENTS_STOPPED 0x108 I2S transfer stopped.
EVENTS_TXPTRUPD 0x114 The TDX.PTR register has been copied to internal double-buffers. When the I2S module is started
and TX is enabled, this event will be generated for every RXTXD.MAXCNT words that are sent on the
SDOUT pin.
INTEN 0x300 Enable or disable interrupt
INTENSET 0x304 Enable interrupt
INTENCLR 0x308 Disable interrupt
ENABLE 0x500 Enable I2S module.
CONFIG.MODE 0x504 I2S mode.
CONFIG.RXEN 0x508 Reception (RX) enable.
CONFIG.TXEN 0x50C Transmission (TX) enable.
CONFIG.MCKEN 0x510 Master clock generator enable.
CONFIG.MCKFREQ 0x514 Master clock generator frequency.
CONFIG.RATIO 0x518 MCK / LRCK ratio.
CONFIG.SWIDTH 0x51C Sample width.
CONFIG.ALIGN 0x520 Alignment of sample within a frame.
CONFIG.FORMAT 0x524 Frame format.
CONFIG.CHANNELS 0x528 Enable channels.
RXD.PTR 0x538 Receive buffer RAM start address.
TXD.PTR 0x540 Transmit buffer RAM start address.
RXTXD.MAXCNT 0x550 Size of RXD and TXD buffers.
PSEL.MCK 0x560 Pin select for MCK signal.
PSEL.SCK 0x564 Pin select for SCK signal.
PSEL.LRCK 0x568 Pin select for LRCK signal.
PSEL.SDIN 0x56C Pin select for SDIN signal.
PSEL.SDOUT 0x570 Pin select for SDOUT signal.

4413_417 v1.9 319

 Peripherals

6.11.10.1 TASKS_START
Address offset: 0x000
Starts continuous I2S transfer. Also starts MCK generator when this is enabled.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_START Starts continuous I2S transfer. Also starts MCK generator when this is
enabled.
Trigger 1 Trigger task

6.11.10.2 TASKS_STOP
Address offset: 0x004
Stops I2S transfer. Also stops MCK generator. Triggering this task will cause the STOPPED event to be
generated.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STOP Stops I2S transfer. Also stops MCK generator. Triggering this task will cause
the STOPPED event to be generated.
Trigger 1 Trigger task

6.11.10.3 EVENTS_RXPTRUPD
Address offset: 0x104
The RXD.PTR register has been copied to internal double-buffers. When the I2S module is started and RX is
enabled, this event will be generated for every RXTXD.MAXCNT words that are received on the SDIN pin.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_RXPTRUPD The RXD.PTR register has been copied to internal double-buffers. When the
I2S module is started and RX is enabled, this event will be generated for
every RXTXD.MAXCNT words that are received on the SDIN pin.
NotGenerated 0 Event not generated
Generated 1 Event generated

6.11.10.4 EVENTS_STOPPED
Address offset: 0x108
I2S transfer stopped.

4413_417 v1.9 320

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_STOPPED I2S transfer stopped.
NotGenerated 0 Event not generated
Generated 1 Event generated

6.11.10.5 EVENTS_TXPTRUPD
Address offset: 0x114
The TDX.PTR register has been copied to internal double-buffers. When the I2S module is started and TX is
enabled, this event will be generated for every RXTXD.MAXCNT words that are sent on the SDOUT pin.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_TXPTRUPD The TDX.PTR register has been copied to internal double-buffers. When the
I2S module is started and TX is enabled, this event will be generated for
every RXTXD.MAXCNT words that are sent on the SDOUT pin.
NotGenerated 0 Event not generated
Generated 1 Event generated

6.11.10.6 INTEN
Address offset: 0x300
Enable or disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID F C B

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
B RW RXPTRUPD Enable or disable interrupt for event RXPTRUPD
Disabled 0 Disable
Enabled 1 Enable
C RW STOPPED Enable or disable interrupt for event STOPPED
Disabled 0 Disable
Enabled 1 Enable
F RW TXPTRUPD Enable or disable interrupt for event TXPTRUPD
Disabled 0 Disable
Enabled 1 Enable

6.11.10.7 INTENSET
Address offset: 0x304
Enable interrupt

4413_417 v1.9 321

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID F C B

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
B RW RXPTRUPD Write '1' to enable interrupt for event RXPTRUPD
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW STOPPED Write '1' to enable interrupt for event STOPPED
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
F RW TXPTRUPD Write '1' to enable interrupt for event TXPTRUPD
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.11.10.8 INTENCLR
Address offset: 0x308
Disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID F C B

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
B RW RXPTRUPD Write '1' to disable interrupt for event RXPTRUPD
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW STOPPED Write '1' to disable interrupt for event STOPPED
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
F RW TXPTRUPD Write '1' to disable interrupt for event TXPTRUPD
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.11.10.9 ENABLE
Address offset: 0x500
Enable I2S module.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW ENABLE Enable I2S module.
Disabled 0 Disable
Enabled 1 Enable

4413_417 v1.9 322

 Peripherals

6.11.10.10 CONFIG.MODE
Address offset: 0x504
I2S mode.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW MODE I2S mode.
Master 0 Master mode. SCK and LRCK generated from internal master clcok (MCK)
and output on pins defined by PSEL.xxx.
Slave 1 Slave mode. SCK and LRCK generated by external master and received on
pins defined by PSEL.xxx

6.11.10.11 CONFIG.RXEN
Address offset: 0x508
Reception (RX) enable.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW RXEN Reception (RX) enable.
Disabled 0 Reception disabled and now data will be written to the RXD.PTR address.
Enabled 1 Reception enabled.

6.11.10.12 CONFIG.TXEN
Address offset: 0x50C
Transmission (TX) enable.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000001 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
ID R/W Field Value ID Value Description
A RW TXEN Transmission (TX) enable.
Disabled 0 Transmission disabled and now data will be read from the RXD.TXD address.
Enabled 1 Transmission enabled.

6.11.10.13 CONFIG.MCKEN
Address offset: 0x510
Master clock generator enable.

4413_417 v1.9 323

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000001 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
ID R/W Field Value ID Value Description
A RW MCKEN Master clock generator enable.
Disabled 0 Master clock generator disabled and PSEL.MCK not connected(available as
GPIO).
Enabled 1 Master clock generator running and MCK output on PSEL.MCK.

6.11.10.14 CONFIG.MCKFREQ
Address offset: 0x514
Master clock generator frequency.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x20000000 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW MCKFREQ Master clock generator frequency.
32MDIV8 0x20000000 32 MHz / 8 = 4.0 MHz
32MDIV10 0x18000000 32 MHz / 10 = 3.2 MHz
32MDIV11 0x16000000 32 MHz / 11 = 2.9090909 MHz
32MDIV15 0x11000000 32 MHz / 15 = 2.1333333 MHz
32MDIV16 0x10000000 32 MHz / 16 = 2.0 MHz
32MDIV21 0x0C000000 32 MHz / 21 = 1.5238095
32MDIV23 0x0B000000 32 MHz / 23 = 1.3913043 MHz
32MDIV30 0x08800000 32 MHz / 30 = 1.0666667 MHz
32MDIV31 0x08400000 32 MHz / 31 = 1.0322581 MHz
32MDIV32 0x08000000 32 MHz / 32 = 1.0 MHz
32MDIV42 0x06000000 32 MHz / 42 = 0.7619048 MHz
32MDIV63 0x04100000 32 MHz / 63 = 0.5079365 MHz
32MDIV125 0x020C0000 32 MHz / 125 = 0.256 MHz

6.11.10.15 CONFIG.RATIO
Address offset: 0x518
MCK / LRCK ratio.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A

Reset 0x00000006 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 0
ID R/W Field Value ID Value Description
A RW RATIO MCK / LRCK ratio.
32X 0 LRCK = MCK / 32
48X 1 LRCK = MCK / 48
64X 2 LRCK = MCK / 64
96X 3 LRCK = MCK / 96
128X 4 LRCK = MCK / 128
192X 5 LRCK = MCK / 192
256X 6 LRCK = MCK / 256
384X 7 LRCK = MCK / 384
512X 8 LRCK = MCK / 512

4413_417 v1.9 324

 Peripherals

6.11.10.16 CONFIG.SWIDTH
Address offset: 0x51C
Sample width.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A

Reset 0x00000001 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
ID R/W Field Value ID Value Description
A RW SWIDTH Sample width.
8Bit 0 8 bit.
16Bit 1 16 bit.
24Bit 2 24 bit.

6.11.10.17 CONFIG.ALIGN
Address offset: 0x520
Alignment of sample within a frame.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW ALIGN Alignment of sample within a frame.
Left 0 Left-aligned.
Right 1 Right-aligned.

6.11.10.18 CONFIG.FORMAT
Address offset: 0x524
Frame format.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW FORMAT Frame format.
I2S 0 Original I2S format.
Aligned 1 Alternate (left- or right-aligned) format.

6.11.10.19 CONFIG.CHANNELS
Address offset: 0x528
Enable channels.

4413_417 v1.9 325

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW CHANNELS Enable channels.
Stereo 0 Stereo.
Left 1 Left only.
Right 2 Right only.

6.11.10.20 RXD.PTR
Address offset: 0x538
Receive buffer RAM start address.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PTR Receive buffer Data RAM start address. When receiving, words containing
samples will be written to this address. This address is a word aligned Data
RAM address.

6.11.10.21 TXD.PTR
Address offset: 0x540
Transmit buffer RAM start address.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PTR Transmit buffer Data RAM start address. When transmitting, words
containing samples will be fetched from this address. This address is a word
aligned Data RAM address.

6.11.10.22 RXTXD.MAXCNT
Address offset: 0x550
Size of RXD and TXD buffers.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW MAXCNT Size of RXD and TXD buffers in number of 32 bit words.

6.11.10.23 PSEL.MCK
Address offset: 0x560
Pin select for MCK signal.

4413_417 v1.9 326

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.11.10.24 PSEL.SCK
Address offset: 0x564
Pin select for SCK signal.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.11.10.25 PSEL.LRCK
Address offset: 0x568
Pin select for LRCK signal.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A
Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.11.10.26 PSEL.SDIN
Address offset: 0x56C
Pin select for SDIN signal.

4413_417 v1.9 327

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.11.10.27 PSEL.SDOUT
Address offset: 0x570
Pin select for SDOUT signal.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.11.11 Electrical specification

6.11.11.1 I2S timing specification

Symbol Description Min. Typ. Max. Units

tS_SDIN SDIN setup time before SCK rising 20 ns
tH_SDIN SDIN hold time after SCK rising 15 ns
tS_SDOUT SDOUT setup time after SCK falling 40 ns
tH_SDOUT SDOUT hold time before SCK falling 6 ns
tSCK_LRCK SCLK falling to LRCK edge -5 0 5 ns
fMCK MCK frequency 4000 kHz
fLRCK LRCK frequency 48 kHz
fSCK SCK frequency 2000 kHz
DCCK Clock duty cycle (MCK, LRCK, SCK) 45 55 %

tSCK_LRCK

LRCK

SCK

tS_SDIN tH_SDIN

SDIN

tS_SDOUT
tH_SDOUT
SDOUT

Figure 58: I2S timing diagram

4413_417 v1.9 328

 Peripherals

6.12 LPCOMP — Low-power comparator

Low-power comparator (LPCOMP) compares an input voltage against a reference voltage.
Listed here are the main features of LPCOMP:
• 0 - VDD input range
• Ultra-low power
• Eight input options (AIN0 to AIN7)
• Reference voltage options:
• Two external analog reference inputs, or
• 15-level internal reference ladder (VDD/16)
• Optional hysteresis enable on input
• Can be used as a wakeup source from System OFF mode
In System ON, the LPCOMP can generate separate events on rising and falling edges of a signal, or sample
the current state of the pin as being above or below the selected reference. The block can be configured
to use any of the analog inputs on the device. Additionally, the low-power comparator can be used as an
analog wakeup source from System OFF or System ON. The comparator threshold can be programmed to a
range of fractions of the supply voltage.

Note: LPCOMP cannot be used (STARTed) at the same time as COMP. Only one comparator can be
used at a time.

tasks
EXTREFSEL REFSEL PSEL HYST RESULT
START

STOP
SAMPLE
AIN0 AREF
MUX AIN0
AIN1 AIN1
VDD*1/16 AIN2
AIN3 VIN+
VDD*1/8 MUX +
VDD*3/16 AIN4
VDD*2/8 AIN5
AIN6 Comparator
VDD*5/16 ANADETECT
AIN7 core
VDD*3/8 (signal to POWER module)
VDD*7/16 MUX VIN-
VDD*4/8 -
VDD*9/16
VDD*5/8
VDD*11/16
UP

CROSS

DOWN

READY

VDD*6/8
VDD*13/16
VDD*7/8
VDD*15/16 events

Figure 59: Low-power comparator

The wakeup comparator (LPCOMP) compares an input voltage (VIN+), which comes from an analog input
pin selected via the PSEL register, against a reference voltage (VIN-) selected via registers REFSEL on page
335 and EXTREFSEL.
The PSEL, REFSEL, and EXTREFSEL registers must be configured before the LPCOMP is enabled through the
ENABLE register.
The HYST register allows enabling an optional hysteresis in the comparator core. This hysteresis shall
prevent noise on the signal to create unwanted events. Figure below illustrates the effect of an active
hysteresis on a noisy input signal. It is disabled by default, and shall be configured before enabling
LPCOMP as well.

4413_417 v1.9 329

 Peripherals

VIN+

VIN- + VHYST/2

VIN- - VHYST/2

ABOVE BELOW ABOVE BELOW

Output (VIN+ > (VIN- + VHYST/2)) (VIN+ < (VIN- - VHYST/2)) (VIN+ > (VIN- + VHYST/2))

Figure 60: Effect of hysteresis on a noisy input signal

The LPCOMP is started by triggering the START task. After a startup time of tLPCOMP,STARTUP, the LPCOMP
will generate a READY event to indicate that the comparator is ready to use and the output of the LPCOMP
is correct. The LPCOMP will generate events every time VIN+ crosses VIN-. More specifically, every time
VIN+ rises above VIN- (upward crossing) an UP event is generated along with a CROSS event. Every time
VIN+ falls below VIN- (downward crossing), a DOWN event is generated along with a CROSS event. When
hysteresis is enabled, the upward crossing level becomes (VIN- + VHYST/2), and the downward crossing
level becomes (VIN- - VHYST/2).
The LPCOMP is stopped by triggering the STOP task.
LPCOMP will be operational in both System ON and System OFF mode when it is enabled through the
ENABLE register. See POWER — Power supply on page 80 for more information about power modes. Note
that it is not allowed to go to System OFF when a READY event is pending to be generated.
All LPCOMP registers, including ENABLE, are classified as retained registers when the LPCOMP is enabled.
However, when the device wakes up from System OFF, all LPCOMP registers will be reset.
The LPCOMP can wake up the system from System OFF by asserting the ANADETECT signal. The
ANADETECT signal can be derived from any of the event sources that generate the UP, DOWN and CROSS
events. In case of wakeup from System OFF, no events will be generated, only the ANADETECT signal.
See the ANADETECT register (ANADETECT on page 336) for more information on how to configure the
ANADETECT signal.
The immediate value of the LPCOMP can be sampled to RESULT on page 334 by triggering the SAMPLE
task.
See RESETREAS on page 94 for more information on how to detect a wakeup from LPCOMP.

6.12.1 Shared resources

The LPCOMP shares analog resources with SAADC. While it is possible to use the SAADC at the same time
as the LPCOMP, selecting the same analog input pin for both modules is not supported.
Additionally, LPCOMP shares registers and other resources with other peripherals that have the same ID as
the LPCOMP. See Peripherals with shared ID on page 173 for more information.
The LPCOMP peripheral shall not be disabled (by writing to the ENABLE register) before the peripheral has
been stopped. Failing to do so may result in unpredictable behavior.

6.12.2 Pin configuration

You can use the LPCOMP.PSEL register to select one of the analog input pins, AIN0 through AIN7, as the
analog input pin for the LPCOMP.
See GPIO — General purpose input/output on page 240 for more information about the pins. Similarly,
you can use EXTREFSEL on page 336 to select one of the analog reference input pins, AIN0 and AIN1,

4413_417 v1.9 330

 Peripherals

as input for AREF in case AREF is selected in EXTREFSEL on page 336. The selected analog pins will be
acquired by the LPCOMP when it is enabled through ENABLE on page 335.

6.12.3 Registers
Instances

Instance Base address Description

LPCOMP 0x40013000 Low power comparator

Register overview

Register Offset Description

TASKS_START 0x000 Start comparator
TASKS_STOP 0x004 Stop comparator
TASKS_SAMPLE 0x008 Sample comparator value
EVENTS_READY 0x100 LPCOMP is ready and output is valid
EVENTS_DOWN 0x104 Downward crossing
EVENTS_UP 0x108 Upward crossing
EVENTS_CROSS 0x10C Downward or upward crossing
SHORTS 0x200 Shortcuts between local events and tasks
INTENSET 0x304 Enable interrupt
INTENCLR 0x308 Disable interrupt
RESULT 0x400 Compare result
ENABLE 0x500 Enable LPCOMP
PSEL 0x504 Input pin select
REFSEL 0x508 Reference select
EXTREFSEL 0x50C External reference select
ANADETECT 0x520 Analog detect configuration
HYST 0x538 Comparator hysteresis enable

6.12.3.1 TASKS_START
Address offset: 0x000
Start comparator

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_START Start comparator
Trigger 1 Trigger task

6.12.3.2 TASKS_STOP
Address offset: 0x004
Stop comparator

4413_417 v1.9 331

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STOP Stop comparator
Trigger 1 Trigger task

6.12.3.3 TASKS_SAMPLE
Address offset: 0x008
Sample comparator value

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_SAMPLE Sample comparator value
Trigger 1 Trigger task

6.12.3.4 EVENTS_READY
Address offset: 0x100
LPCOMP is ready and output is valid

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_READY LPCOMP is ready and output is valid
NotGenerated 0 Event not generated
Generated 1 Event generated

6.12.3.5 EVENTS_DOWN
Address offset: 0x104
Downward crossing

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_DOWN Downward crossing
NotGenerated 0 Event not generated
Generated 1 Event generated

6.12.3.6 EVENTS_UP
Address offset: 0x108
Upward crossing

4413_417 v1.9 332

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_UP Upward crossing
NotGenerated 0 Event not generated
Generated 1 Event generated

6.12.3.7 EVENTS_CROSS
Address offset: 0x10C
Downward or upward crossing

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_CROSS Downward or upward crossing
NotGenerated 0 Event not generated
Generated 1 Event generated

6.12.3.8 SHORTS
Address offset: 0x200
Shortcuts between local events and tasks

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW READY_SAMPLE Shortcut between event READY and task SAMPLE
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
B RW READY_STOP Shortcut between event READY and task STOP
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
C RW DOWN_STOP Shortcut between event DOWN and task STOP
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
D RW UP_STOP Shortcut between event UP and task STOP
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
E RW CROSS_STOP Shortcut between event CROSS and task STOP
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut

6.12.3.9 INTENSET
Address offset: 0x304
Enable interrupt

4413_417 v1.9 333

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW READY Write '1' to enable interrupt for event READY
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW DOWN Write '1' to enable interrupt for event DOWN
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW UP Write '1' to enable interrupt for event UP
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
D RW CROSS Write '1' to enable interrupt for event CROSS
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.12.3.10 INTENCLR
Address offset: 0x308
Disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW READY Write '1' to disable interrupt for event READY
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW DOWN Write '1' to disable interrupt for event DOWN
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW UP Write '1' to disable interrupt for event UP
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
D RW CROSS Write '1' to disable interrupt for event CROSS
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.12.3.11 RESULT
Address offset: 0x400
Compare result

4413_417 v1.9 334

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R RESULT Result of last compare. Decision point SAMPLE task.
Below 0 Input voltage is below the reference threshold (VIN+ < VIN-)
Above 1 Input voltage is above the reference threshold (VIN+ > VIN-)

6.12.3.12 ENABLE
Address offset: 0x500
Enable LPCOMP

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW ENABLE Enable or disable LPCOMP
Disabled 0 Disable
Enabled 1 Enable

6.12.3.13 PSEL
Address offset: 0x504
Input pin select

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PSEL Analog pin select
AnalogInput0 0 AIN0 selected as analog input
AnalogInput1 1 AIN1 selected as analog input
AnalogInput2 2 AIN2 selected as analog input
AnalogInput3 3 AIN3 selected as analog input
AnalogInput4 4 AIN4 selected as analog input
AnalogInput5 5 AIN5 selected as analog input
AnalogInput6 6 AIN6 selected as analog input
AnalogInput7 7 AIN7 selected as analog input

6.12.3.14 REFSEL
Address offset: 0x508
Reference select

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A

Reset 0x00000004 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0
ID R/W Field Value ID Value Description
A RW REFSEL Reference select
Ref1_8Vdd 0 VDD * 1/8 selected as reference
Ref2_8Vdd 1 VDD * 2/8 selected as reference

4413_417 v1.9 335

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A

Reset 0x00000004 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0
ID R/W Field Value ID Value Description
Ref3_8Vdd 2 VDD * 3/8 selected as reference
Ref4_8Vdd 3 VDD * 4/8 selected as reference
Ref5_8Vdd 4 VDD * 5/8 selected as reference
Ref6_8Vdd 5 VDD * 6/8 selected as reference
Ref7_8Vdd 6 VDD * 7/8 selected as reference
ARef 7 External analog reference selected
Ref1_16Vdd 8 VDD * 1/16 selected as reference
Ref3_16Vdd 9 VDD * 3/16 selected as reference
Ref5_16Vdd 10 VDD * 5/16 selected as reference
Ref7_16Vdd 11 VDD * 7/16 selected as reference
Ref9_16Vdd 12 VDD * 9/16 selected as reference
Ref11_16Vdd 13 VDD * 11/16 selected as reference
Ref13_16Vdd 14 VDD * 13/16 selected as reference
Ref15_16Vdd 15 VDD * 15/16 selected as reference

6.12.3.15 EXTREFSEL
Address offset: 0x50C
External reference select

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A- RW EXTREFSEL External analog reference select
AnalogReference0 0 Use AIN0 as external analog reference
AnalogReference1 1 Use AIN1 as external analog reference

6.12.3.16 ANADETECT
Address offset: 0x520
Analog detect configuration

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW ANADETECT Analog detect configuration
Cross 0 Generate ANADETECT on crossing, both upward crossing and downward
crossing
Up 1 Generate ANADETECT on upward crossing only
Down 2 Generate ANADETECT on downward crossing only

6.12.3.17 HYST
Address offset: 0x538
Comparator hysteresis enable

4413_417 v1.9 336

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW HYST Comparator hysteresis enable
Disabled 0 Comparator hysteresis disabled
Enabled 1 Comparator hysteresis enabled

6.12.4 Electrical specification

6.12.4.1 LPCOMP Electrical Specification

Symbol Description Min. Typ. Max. Units

tLPCANADET Time from VIN crossing (>=50 mV above threshold) to ANADETECT signal 5 µs
generated
VINPOFFSET Input offset including reference ladder error -40 40 mV
VHYST Optional hysteresis 35 mV
tSTARTUP Startup time for LPCOMP 140 µs

6.13 MWU — Memory watch unit

The Memory watch unit (MWU) can be used to generate events when a memory region is accessed
by the CPU. The MWU can be configured to trigger events for access to Data RAM and Peripheral
memory segments. The MWU allows an application developer to generate memory access events during
development for debugging or during production execution for failure detection and recovery.
Listed here are the main features for MWU:
• Six memory regions, four user-configurable and two fixed regions in peripheral address space
• Flexible configuration of regions with START and END addresses
• Generate events on CPU read and/or write to a defined region of Data RAM or peripheral memory
address space
• Programmable maskable or non-maskable (NMI) interrupt on events
• Peripheral interfaces can be watched for read and write access using subregions of the two fixed
memory regions

Memory region START address END address

REGION[0..3] Configurable Configurable
PREGION[0] 0x40000000 0x4001FFFF
PREGION[1] 0x40020000 0x4003FFFF

Table 24: Memory regions

Each MWU region is defined by a start address and an end address, configured by the START and END
registers respectively. These addresses are byte aligned and inclusive. The END register value has to be
greater or equal to the START register value. Each region is associated with a pair of events that indicate
that either a write access or a read access from the CPU has been detected inside the region.
For regions containing subregions (see below), a set of status registers PERREGION[0..1].SUBSTATWA
and PERREGION[0..1].SUBSTATRA indicate which subregion(s) caused the EVENT_PREGION[0..1].WA and
EVENT_PREGION[0..1].RA respectively.
The MWU is only able to detect memory accesses in the Data RAM and Peripheral memory segments from
the CPU, see Memory on page 21 for more information about the different memory segments. EasyDMA

4413_417 v1.9 337

 Peripherals

accesses are not monitored by the MWU. The MWU requires two HCLK cycles to detect and generate the
event.
The peripheral regions, PREGION[0...1], are divided into 32 equally sized subregions, SR[0...31]. All
subregions are excluded in the main region by default, and any can be included by specifying them in the
SUBS register. When a subregion is excluded from the main region, the memory watch mechanism will not
trigger any events when that subregion is accessed.
Subregions in PREGION[0..1] cannot be individually configured for read or write access watch. Watch
configuration is only possible for a region as a whole. The PRGNiRA and PRGNiWA (i=0..1) fields in the
REGIONEN register control watching read and write access.
REGION[0..3] can be individually enabled for read and/or write access watching through their respective
RGNiRA and RGNiWA (i=0..3) fields in the REGIONEN register.
REGIONENSET and REGIONENCLR allow respectively enabling and disabling one or multiple REGIONs or
PREGIONs watching in a single write access.

6.13.1 Registers
Instances

Instance Base address Description

MWU 0x40020000 Memory watch unit

Register overview

Register Offset Description

EVENTS_REGION[0].WA 0x100 Write access to region 0 detected
EVENTS_REGION[0].RA 0x104 Read access to region 0 detected
EVENTS_REGION[1].WA 0x108 Write access to region 1 detected
EVENTS_REGION[1].RA 0x10C Read access to region 1 detected
EVENTS_REGION[2].WA 0x110 Write access to region 2 detected
EVENTS_REGION[2].RA 0x114 Read access to region 2 detected
EVENTS_REGION[3].WA 0x118 Write access to region 3 detected
EVENTS_REGION[3].RA 0x11C Read access to region 3 detected
EVENTS_PREGION[0].WA 0x160 Write access to peripheral region 0 detected
EVENTS_PREGION[0].RA 0x164 Read access to peripheral region 0 detected
EVENTS_PREGION[1].WA 0x168 Write access to peripheral region 1 detected
EVENTS_PREGION[1].RA 0x16C Read access to peripheral region 1 detected
INTEN 0x300 Enable or disable interrupt
INTENSET 0x304 Enable interrupt
INTENCLR 0x308 Disable interrupt
NMIEN 0x320 Enable or disable interrupt
NMIENSET 0x324 Enable interrupt
NMIENCLR 0x328 Disable interrupt
PERREGION[0].SUBSTATWA 0x400 Source of event/interrupt in region 0, write access detected while corresponding subregion was
enabled for watching
PERREGION[0].SUBSTATRA 0x404 Source of event/interrupt in region 0, read access detected while corresponding subregion was
enabled for watching
PERREGION[1].SUBSTATWA 0x408 Source of event/interrupt in region 1, write access detected while corresponding subregion was
enabled for watching
PERREGION[1].SUBSTATRA 0x40C Source of event/interrupt in region 1, read access detected while corresponding subregion was
enabled for watching

4413_417 v1.9 338

 Peripherals

Register Offset Description

REGIONEN 0x510 Enable/disable regions watch
REGIONENSET 0x514 Enable regions watch
REGIONENCLR 0x518 Disable regions watch
REGION[0].START 0x600 Start address for region 0
REGION[0].END 0x604 End address of region 0
REGION[1].START 0x610 Start address for region 1
REGION[1].END 0x614 End address of region 1
REGION[2].START 0x620 Start address for region 2
REGION[2].END 0x624 End address of region 2
REGION[3].START 0x630 Start address for region 3
REGION[3].END 0x634 End address of region 3
PREGION[0].START 0x6C0 Reserved for future use
PREGION[0].END 0x6C4 Reserved for future use
PREGION[0].SUBS 0x6C8 Subregions of region 0
PREGION[1].START 0x6D0 Reserved for future use
PREGION[1].END 0x6D4 Reserved for future use
PREGION[1].SUBS 0x6D8 Subregions of region 1

6.13.1.1 EVENTS_REGION[0]
Peripheral events.

6.13.1.1.1 EVENTS_REGION[0].WA
Address offset: 0x100
Write access to region 0 detected

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW WA Write access to region 0 detected
NotGenerated 0 Event not generated
Generated 1 Event generated

6.13.1.1.2 EVENTS_REGION[0].RA
Address offset: 0x104
Read access to region 0 detected

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW RA Read access to region 0 detected
NotGenerated 0 Event not generated
Generated 1 Event generated

6.13.1.2 EVENTS_REGION[1]
Peripheral events.

4413_417 v1.9 339

 Peripherals

6.13.1.2.1 EVENTS_REGION[1].WA
Address offset: 0x108
Write access to region 1 detected

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW WA Write access to region 1 detected
NotGenerated 0 Event not generated
Generated 1 Event generated

6.13.1.2.2 EVENTS_REGION[1].RA
Address offset: 0x10C
Read access to region 1 detected

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW RA Read access to region 1 detected
NotGenerated 0 Event not generated
Generated 1 Event generated

6.13.1.3 EVENTS_REGION[2]
Peripheral events.

6.13.1.3.1 EVENTS_REGION[2].WA
Address offset: 0x110
Write access to region 2 detected

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW WA Write access to region 2 detected
NotGenerated 0 Event not generated
Generated 1 Event generated

6.13.1.3.2 EVENTS_REGION[2].RA
Address offset: 0x114
Read access to region 2 detected

4413_417 v1.9 340

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW RA Read access to region 2 detected
NotGenerated 0 Event not generated
Generated 1 Event generated

6.13.1.4 EVENTS_REGION[3]
Peripheral events.

6.13.1.4.1 EVENTS_REGION[3].WA
Address offset: 0x118
Write access to region 3 detected

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW WA Write access to region 3 detected
NotGenerated 0 Event not generated
Generated 1 Event generated

6.13.1.4.2 EVENTS_REGION[3].RA
Address offset: 0x11C
Read access to region 3 detected

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW RA Read access to region 3 detected
NotGenerated 0 Event not generated
Generated 1 Event generated

6.13.1.5 EVENTS_PREGION[0]
Peripheral events.

6.13.1.5.1 EVENTS_PREGION[0].WA
Address offset: 0x160
Write access to peripheral region 0 detected

4413_417 v1.9 341

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW WA Write access to peripheral region 0 detected
NotGenerated 0 Event not generated
Generated 1 Event generated

6.13.1.5.2 EVENTS_PREGION[0].RA
Address offset: 0x164
Read access to peripheral region 0 detected

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW RA Read access to peripheral region 0 detected
NotGenerated 0 Event not generated
Generated 1 Event generated

6.13.1.6 EVENTS_PREGION[1]
Peripheral events.

6.13.1.6.1 EVENTS_PREGION[1].WA
Address offset: 0x168
Write access to peripheral region 1 detected

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW WA Write access to peripheral region 1 detected
NotGenerated 0 Event not generated
Generated 1 Event generated

6.13.1.6.2 EVENTS_PREGION[1].RA
Address offset: 0x16C
Read access to peripheral region 1 detected

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW RA Read access to peripheral region 1 detected
NotGenerated 0 Event not generated
Generated 1 Event generated

4413_417 v1.9 342

 Peripherals

6.13.1.7 INTEN
Address offset: 0x300
Enable or disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW REGION0WA Enable or disable interrupt for event REGION0WA
Disabled 0 Disable
Enabled 1 Enable
B RW REGION0RA Enable or disable interrupt for event REGION0RA
Disabled 0 Disable
Enabled 1 Enable
C RW REGION1WA Enable or disable interrupt for event REGION1WA
Disabled 0 Disable
Enabled 1 Enable
D RW REGION1RA Enable or disable interrupt for event REGION1RA
Disabled 0 Disable
Enabled 1 Enable
E RW REGION2WA Enable or disable interrupt for event REGION2WA
Disabled 0 Disable
Enabled 1 Enable
F RW REGION2RA Enable or disable interrupt for event REGION2RA
Disabled 0 Disable
Enabled 1 Enable
G RW REGION3WA Enable or disable interrupt for event REGION3WA
Disabled 0 Disable
Enabled 1 Enable
H RW REGION3RA Enable or disable interrupt for event REGION3RA
Disabled 0 Disable
Enabled 1 Enable
I RW PREGION0WA Enable or disable interrupt for event PREGION0WA
Disabled 0 Disable
Enabled 1 Enable
J RW PREGION0RA Enable or disable interrupt for event PREGION0RA
Disabled 0 Disable
Enabled 1 Enable
K RW PREGION1WA Enable or disable interrupt for event PREGION1WA
Disabled 0 Disable
Enabled 1 Enable
L RW PREGION1RA Enable or disable interrupt for event PREGION1RA
Disabled 0 Disable
Enabled 1 Enable

6.13.1.8 INTENSET
Address offset: 0x304
Enable interrupt

4413_417 v1.9 343

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW REGION0WA Write '1' to enable interrupt for event REGION0WA
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW REGION0RA Write '1' to enable interrupt for event REGION0RA
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW REGION1WA Write '1' to enable interrupt for event REGION1WA
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
D RW REGION1RA Write '1' to enable interrupt for event REGION1RA
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
E RW REGION2WA Write '1' to enable interrupt for event REGION2WA
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
F RW REGION2RA Write '1' to enable interrupt for event REGION2RA
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
G RW REGION3WA Write '1' to enable interrupt for event REGION3WA
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
H RW REGION3RA Write '1' to enable interrupt for event REGION3RA
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
I RW PREGION0WA Write '1' to enable interrupt for event PREGION0WA
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
J RW PREGION0RA Write '1' to enable interrupt for event PREGION0RA
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
K RW PREGION1WA Write '1' to enable interrupt for event PREGION1WA
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
L RW PREGION1RA Write '1' to enable interrupt for event PREGION1RA
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

4413_417 v1.9 344

 Peripherals

6.13.1.9 INTENCLR
Address offset: 0x308
Disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW REGION0WA Write '1' to disable interrupt for event REGION0WA
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW REGION0RA Write '1' to disable interrupt for event REGION0RA
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW REGION1WA Write '1' to disable interrupt for event REGION1WA
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
D RW REGION1RA Write '1' to disable interrupt for event REGION1RA
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
E RW REGION2WA Write '1' to disable interrupt for event REGION2WA
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
F RW REGION2RA Write '1' to disable interrupt for event REGION2RA
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
G RW REGION3WA Write '1' to disable interrupt for event REGION3WA
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
H RW REGION3RA Write '1' to disable interrupt for event REGION3RA
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
I RW PREGION0WA Write '1' to disable interrupt for event PREGION0WA
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
J RW PREGION0RA Write '1' to disable interrupt for event PREGION0RA
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
K RW PREGION1WA Write '1' to disable interrupt for event PREGION1WA
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

4413_417 v1.9 345

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
L RW PREGION1RA Write '1' to disable interrupt for event PREGION1RA
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.13.1.10 NMIEN
Address offset: 0x320
Enable or disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW REGION0WA Enable or disable interrupt for event REGION0WA
Disabled 0 Disable
Enabled 1 Enable
B RW REGION0RA Enable or disable interrupt for event REGION0RA
Disabled 0 Disable
Enabled 1 Enable
C RW REGION1WA Enable or disable interrupt for event REGION1WA
Disabled 0 Disable
Enabled 1 Enable
D RW REGION1RA Enable or disable interrupt for event REGION1RA
Disabled 0 Disable
Enabled 1 Enable
E RW REGION2WA Enable or disable interrupt for event REGION2WA
Disabled 0 Disable
Enabled 1 Enable
F RW REGION2RA Enable or disable interrupt for event REGION2RA
Disabled 0 Disable
Enabled 1 Enable
G RW REGION3WA Enable or disable interrupt for event REGION3WA
Disabled 0 Disable
Enabled 1 Enable
H RW REGION3RA Enable or disable interrupt for event REGION3RA
Disabled 0 Disable
Enabled 1 Enable
I RW PREGION0WA Enable or disable interrupt for event PREGION0WA
Disabled 0 Disable
Enabled 1 Enable
J RW PREGION0RA Enable or disable interrupt for event PREGION0RA
Disabled 0 Disable
Enabled 1 Enable
K RW PREGION1WA Enable or disable interrupt for event PREGION1WA
Disabled 0 Disable
Enabled 1 Enable
L RW PREGION1RA Enable or disable interrupt for event PREGION1RA
Disabled 0 Disable

4413_417 v1.9 346

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Enabled 1 Enable

6.13.1.11 NMIENSET
Address offset: 0x324
Enable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW REGION0WA Write '1' to enable interrupt for event REGION0WA
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW REGION0RA Write '1' to enable interrupt for event REGION0RA
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW REGION1WA Write '1' to enable interrupt for event REGION1WA
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
D RW REGION1RA Write '1' to enable interrupt for event REGION1RA
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
E RW REGION2WA Write '1' to enable interrupt for event REGION2WA
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
F RW REGION2RA Write '1' to enable interrupt for event REGION2RA
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
G RW REGION3WA Write '1' to enable interrupt for event REGION3WA
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
H RW REGION3RA Write '1' to enable interrupt for event REGION3RA
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
I RW PREGION0WA Write '1' to enable interrupt for event PREGION0WA
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
J RW PREGION0RA Write '1' to enable interrupt for event PREGION0RA
Set 1 Enable

4413_417 v1.9 347

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
K RW PREGION1WA Write '1' to enable interrupt for event PREGION1WA
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
L RW PREGION1RA Write '1' to enable interrupt for event PREGION1RA
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.13.1.12 NMIENCLR
Address offset: 0x328
Disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW REGION0WA Write '1' to disable interrupt for event REGION0WA
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW REGION0RA Write '1' to disable interrupt for event REGION0RA
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW REGION1WA Write '1' to disable interrupt for event REGION1WA
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
D RW REGION1RA Write '1' to disable interrupt for event REGION1RA
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
E RW REGION2WA Write '1' to disable interrupt for event REGION2WA
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
F RW REGION2RA Write '1' to disable interrupt for event REGION2RA
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
G RW REGION3WA Write '1' to disable interrupt for event REGION3WA
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
H RW REGION3RA Write '1' to disable interrupt for event REGION3RA

4413_417 v1.9 348

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
I RW PREGION0WA Write '1' to disable interrupt for event PREGION0WA
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
J RW PREGION0RA Write '1' to disable interrupt for event PREGION0RA
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
K RW PREGION1WA Write '1' to disable interrupt for event PREGION1WA
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
L RW PREGION1RA Write '1' to disable interrupt for event PREGION1RA
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.13.1.13 PERREGION[0].SUBSTATWA
Address offset: 0x400
Source of event/interrupt in region 0, write access detected while corresponding subregion was enabled
for watching

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW SR0 Subregion 0 in region 0 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
B RW SR1 Subregion 1 in region 0 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
C RW SR2 Subregion 2 in region 0 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
D RW SR3 Subregion 3 in region 0 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
E RW SR4 Subregion 4 in region 0 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion

4413_417 v1.9 349

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Access 1 Write access(es) occurred in this subregion
F RW SR5 Subregion 5 in region 0 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
G RW SR6 Subregion 6 in region 0 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
H RW SR7 Subregion 7 in region 0 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
I RW SR8 Subregion 8 in region 0 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
J RW SR9 Subregion 9 in region 0 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
K RW SR10 Subregion 10 in region 0 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
L RW SR11 Subregion 11 in region 0 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
M RW SR12 Subregion 12 in region 0 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
N RW SR13 Subregion 13 in region 0 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
O RW SR14 Subregion 14 in region 0 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
P RW SR15 Subregion 15 in region 0 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
Q RW SR16 Subregion 16 in region 0 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion

4413_417 v1.9 350

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
R RW SR17 Subregion 17 in region 0 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
S RW SR18 Subregion 18 in region 0 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
T RW SR19 Subregion 19 in region 0 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
U RW SR20 Subregion 20 in region 0 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
V RW SR21 Subregion 21 in region 0 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
W RW SR22 Subregion 22 in region 0 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
X RW SR23 Subregion 23 in region 0 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
Y RW SR24 Subregion 24 in region 0 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
Z RW SR25 Subregion 25 in region 0 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
a RW SR26 Subregion 26 in region 0 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
b RW SR27 Subregion 27 in region 0 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
c RW SR28 Subregion 28 in region 0 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
d RW SR29 Subregion 29 in region 0 (write '1' to clear)
W1C

4413_417 v1.9 351

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
e RW SR30 Subregion 30 in region 0 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
f RW SR31 Subregion 31 in region 0 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion

6.13.1.14 PERREGION[0].SUBSTATRA
Address offset: 0x404
Source of event/interrupt in region 0, read access detected while corresponding subregion was enabled
for watching

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW SR0 Subregion 0 in region 0 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
B RW SR1 Subregion 1 in region 0 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
C RW SR2 Subregion 2 in region 0 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
D RW SR3 Subregion 3 in region 0 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
E RW SR4 Subregion 4 in region 0 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
F RW SR5 Subregion 5 in region 0 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
G RW SR6 Subregion 6 in region 0 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion

4413_417 v1.9 352

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
H RW SR7 Subregion 7 in region 0 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
I RW SR8 Subregion 8 in region 0 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
J RW SR9 Subregion 9 in region 0 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
K RW SR10 Subregion 10 in region 0 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
L RW SR11 Subregion 11 in region 0 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
M RW SR12 Subregion 12 in region 0 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
N RW SR13 Subregion 13 in region 0 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
O RW SR14 Subregion 14 in region 0 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
P RW SR15 Subregion 15 in region 0 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
Q RW SR16 Subregion 16 in region 0 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
R RW SR17 Subregion 17 in region 0 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
S RW SR18 Subregion 18 in region 0 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
T RW SR19 Subregion 19 in region 0 (write '1' to clear)
W1C

4413_417 v1.9 353

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
U RW SR20 Subregion 20 in region 0 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
V RW SR21 Subregion 21 in region 0 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
W RW SR22 Subregion 22 in region 0 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
X RW SR23 Subregion 23 in region 0 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
Y RW SR24 Subregion 24 in region 0 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
Z RW SR25 Subregion 25 in region 0 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
a RW SR26 Subregion 26 in region 0 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
b RW SR27 Subregion 27 in region 0 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
c RW SR28 Subregion 28 in region 0 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
d RW SR29 Subregion 29 in region 0 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
e RW SR30 Subregion 30 in region 0 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
f RW SR31 Subregion 31 in region 0 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion

4413_417 v1.9 354

 Peripherals

6.13.1.15 PERREGION[1].SUBSTATWA
Address offset: 0x408
Source of event/interrupt in region 1, write access detected while corresponding subregion was enabled
for watching

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW SR0 Subregion 0 in region 1 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
B RW SR1 Subregion 1 in region 1 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
C RW SR2 Subregion 2 in region 1 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
D RW SR3 Subregion 3 in region 1 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
E RW SR4 Subregion 4 in region 1 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
F RW SR5 Subregion 5 in region 1 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
G RW SR6 Subregion 6 in region 1 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
H RW SR7 Subregion 7 in region 1 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
I RW SR8 Subregion 8 in region 1 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
J RW SR9 Subregion 9 in region 1 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
K RW SR10 Subregion 10 in region 1 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion

4413_417 v1.9 355

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Access 1 Write access(es) occurred in this subregion
L RW SR11 Subregion 11 in region 1 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
M RW SR12 Subregion 12 in region 1 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
N RW SR13 Subregion 13 in region 1 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
O RW SR14 Subregion 14 in region 1 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
P RW SR15 Subregion 15 in region 1 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
Q RW SR16 Subregion 16 in region 1 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
R RW SR17 Subregion 17 in region 1 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
S RW SR18 Subregion 18 in region 1 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
T RW SR19 Subregion 19 in region 1 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
U RW SR20 Subregion 20 in region 1 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
V RW SR21 Subregion 21 in region 1 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
W RW SR22 Subregion 22 in region 1 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion

4413_417 v1.9 356

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
X RW SR23 Subregion 23 in region 1 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
Y RW SR24 Subregion 24 in region 1 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
Z RW SR25 Subregion 25 in region 1 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
a RW SR26 Subregion 26 in region 1 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
b RW SR27 Subregion 27 in region 1 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
c RW SR28 Subregion 28 in region 1 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
d RW SR29 Subregion 29 in region 1 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
e RW SR30 Subregion 30 in region 1 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion
f RW SR31 Subregion 31 in region 1 (write '1' to clear)
W1C
NoAccess 0 No write access occurred in this subregion
Access 1 Write access(es) occurred in this subregion

6.13.1.16 PERREGION[1].SUBSTATRA
Address offset: 0x40C
Source of event/interrupt in region 1, read access detected while corresponding subregion was enabled
for watching

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW SR0 Subregion 0 in region 1 (write '1' to clear)
W1C

4413_417 v1.9 357

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
B RW SR1 Subregion 1 in region 1 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
C RW SR2 Subregion 2 in region 1 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
D RW SR3 Subregion 3 in region 1 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
E RW SR4 Subregion 4 in region 1 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
F RW SR5 Subregion 5 in region 1 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
G RW SR6 Subregion 6 in region 1 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
H RW SR7 Subregion 7 in region 1 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
I RW SR8 Subregion 8 in region 1 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
J RW SR9 Subregion 9 in region 1 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
K RW SR10 Subregion 10 in region 1 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
L RW SR11 Subregion 11 in region 1 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
M RW SR12 Subregion 12 in region 1 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion

4413_417 v1.9 358

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
N RW SR13 Subregion 13 in region 1 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
O RW SR14 Subregion 14 in region 1 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
P RW SR15 Subregion 15 in region 1 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
Q RW SR16 Subregion 16 in region 1 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
R RW SR17 Subregion 17 in region 1 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
S RW SR18 Subregion 18 in region 1 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
T RW SR19 Subregion 19 in region 1 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
U RW SR20 Subregion 20 in region 1 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
V RW SR21 Subregion 21 in region 1 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
W RW SR22 Subregion 22 in region 1 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
X RW SR23 Subregion 23 in region 1 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
Y RW SR24 Subregion 24 in region 1 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
Z RW SR25 Subregion 25 in region 1 (write '1' to clear)
W1C

4413_417 v1.9 359

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
a RW SR26 Subregion 26 in region 1 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
b RW SR27 Subregion 27 in region 1 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
c RW SR28 Subregion 28 in region 1 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
d RW SR29 Subregion 29 in region 1 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
e RW SR30 Subregion 30 in region 1 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion
f RW SR31 Subregion 31 in region 1 (write '1' to clear)
W1C
NoAccess 0 No read access occurred in this subregion
Access 1 Read access(es) occurred in this subregion

6.13.1.17 REGIONEN
Address offset: 0x510
Enable/disable regions watch

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW RGN0WA Enable/disable write access watch in region[0]
Disable 0 Disable write access watch in this region
Enable 1 Enable write access watch in this region
B RW RGN0RA Enable/disable read access watch in region[0]
Disable 0 Disable read access watch in this region
Enable 1 Enable read access watch in this region
C RW RGN1WA Enable/disable write access watch in region[1]
Disable 0 Disable write access watch in this region
Enable 1 Enable write access watch in this region
D RW RGN1RA Enable/disable read access watch in region[1]
Disable 0 Disable read access watch in this region
Enable 1 Enable read access watch in this region
E RW RGN2WA Enable/disable write access watch in region[2]

4413_417 v1.9 360

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Disable 0 Disable write access watch in this region
Enable 1 Enable write access watch in this region
F RW RGN2RA Enable/disable read access watch in region[2]
Disable 0 Disable read access watch in this region
Enable 1 Enable read access watch in this region
G RW RGN3WA Enable/disable write access watch in region[3]
Disable 0 Disable write access watch in this region
Enable 1 Enable write access watch in this region
H RW RGN3RA Enable/disable read access watch in region[3]
Disable 0 Disable read access watch in this region
Enable 1 Enable read access watch in this region
I RW PRGN0WA Enable/disable write access watch in PREGION[0]
Disable 0 Disable write access watch in this PREGION
Enable 1 Enable write access watch in this PREGION
J RW PRGN0RA Enable/disable read access watch in PREGION[0]
Disable 0 Disable read access watch in this PREGION
Enable 1 Enable read access watch in this PREGION
K RW PRGN1WA Enable/disable write access watch in PREGION[1]
Disable 0 Disable write access watch in this PREGION
Enable 1 Enable write access watch in this PREGION
L RW PRGN1RA Enable/disable read access watch in PREGION[1]
Disable 0 Disable read access watch in this PREGION
Enable 1 Enable read access watch in this PREGION

6.13.1.18 REGIONENSET
Address offset: 0x514
Enable regions watch

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW RGN0WA Enable write access watch in region[0]
Set 1 Enable write access watch in this region
Disabled 0 Write access watch in this region is disabled
Enabled 1 Write access watch in this region is enabled
B RW RGN0RA Enable read access watch in region[0]
Set 1 Enable read access watch in this region
Disabled 0 Read access watch in this region is disabled
Enabled 1 Read access watch in this region is enabled
C RW RGN1WA Enable write access watch in region[1]
Set 1 Enable write access watch in this region
Disabled 0 Write access watch in this region is disabled
Enabled 1 Write access watch in this region is enabled
D RW RGN1RA Enable read access watch in region[1]
Set 1 Enable read access watch in this region
Disabled 0 Read access watch in this region is disabled
Enabled 1 Read access watch in this region is enabled

4413_417 v1.9 361

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
E RW RGN2WA Enable write access watch in region[2]
Set 1 Enable write access watch in this region
Disabled 0 Write access watch in this region is disabled
Enabled 1 Write access watch in this region is enabled
F RW RGN2RA Enable read access watch in region[2]
Set 1 Enable read access watch in this region
Disabled 0 Read access watch in this region is disabled
Enabled 1 Read access watch in this region is enabled
G RW RGN3WA Enable write access watch in region[3]
Set 1 Enable write access watch in this region
Disabled 0 Write access watch in this region is disabled
Enabled 1 Write access watch in this region is enabled
H RW RGN3RA Enable read access watch in region[3]
Set 1 Enable read access watch in this region
Disabled 0 Read access watch in this region is disabled
Enabled 1 Read access watch in this region is enabled
I RW PRGN0WA Enable write access watch in PREGION[0]
Set 1 Enable write access watch in this PREGION
Disabled 0 Write access watch in this PREGION is disabled
Enabled 1 Write access watch in this PREGION is enabled
J RW PRGN0RA Enable read access watch in PREGION[0]
Set 1 Enable read access watch in this PREGION
Disabled 0 Read access watch in this PREGION is disabled
Enabled 1 Read access watch in this PREGION is enabled
K RW PRGN1WA Enable write access watch in PREGION[1]
Set 1 Enable write access watch in this PREGION
Disabled 0 Write access watch in this PREGION is disabled
Enabled 1 Write access watch in this PREGION is enabled
L RW PRGN1RA Enable read access watch in PREGION[1]
Set 1 Enable read access watch in this PREGION
Disabled 0 Read access watch in this PREGION is disabled
Enabled 1 Read access watch in this PREGION is enabled

6.13.1.19 REGIONENCLR
Address offset: 0x518
Disable regions watch

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW RGN0WA Disable write access watch in region[0]
Clear 1 Disable write access watch in this region
Disabled 0 Write access watch in this region is disabled
Enabled 1 Write access watch in this region is enabled
B RW RGN0RA Disable read access watch in region[0]
Clear 1 Disable read access watch in this region
Disabled 0 Read access watch in this region is disabled

4413_417 v1.9 362

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Enabled 1 Read access watch in this region is enabled
C RW RGN1WA Disable write access watch in region[1]
Clear 1 Disable write access watch in this region
Disabled 0 Write access watch in this region is disabled
Enabled 1 Write access watch in this region is enabled
D RW RGN1RA Disable read access watch in region[1]
Clear 1 Disable read access watch in this region
Disabled 0 Read access watch in this region is disabled
Enabled 1 Read access watch in this region is enabled
E RW RGN2WA Disable write access watch in region[2]
Clear 1 Disable write access watch in this region
Disabled 0 Write access watch in this region is disabled
Enabled 1 Write access watch in this region is enabled
F RW RGN2RA Disable read access watch in region[2]
Clear 1 Disable read access watch in this region
Disabled 0 Read access watch in this region is disabled
Enabled 1 Read access watch in this region is enabled
G RW RGN3WA Disable write access watch in region[3]
Clear 1 Disable write access watch in this region
Disabled 0 Write access watch in this region is disabled
Enabled 1 Write access watch in this region is enabled
H RW RGN3RA Disable read access watch in region[3]
Clear 1 Disable read access watch in this region
Disabled 0 Read access watch in this region is disabled
Enabled 1 Read access watch in this region is enabled
I RW PRGN0WA Disable write access watch in PREGION[0]
Clear 1 Disable write access watch in this PREGION
Disabled 0 Write access watch in this PREGION is disabled
Enabled 1 Write access watch in this PREGION is enabled
J RW PRGN0RA Disable read access watch in PREGION[0]
Clear 1 Disable read access watch in this PREGION
Disabled 0 Read access watch in this PREGION is disabled
Enabled 1 Read access watch in this PREGION is enabled
K RW PRGN1WA Disable write access watch in PREGION[1]
Clear 1 Disable write access watch in this PREGION
Disabled 0 Write access watch in this PREGION is disabled
Enabled 1 Write access watch in this PREGION is enabled
L RW PRGN1RA Disable read access watch in PREGION[1]
Clear 1 Disable read access watch in this PREGION
Disabled 0 Read access watch in this PREGION is disabled
Enabled 1 Read access watch in this PREGION is enabled

6.13.1.20 REGION[0].START
Address offset: 0x600
Start address for region 0

4413_417 v1.9 363

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW START Start address for region

6.13.1.21 REGION[0].END
Address offset: 0x604
End address of region 0

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW END End address of region.

6.13.1.22 REGION[1].START
Address offset: 0x610
Start address for region 1

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW START Start address for region

6.13.1.23 REGION[1].END
Address offset: 0x614
End address of region 1

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW END End address of region.

6.13.1.24 REGION[2].START
Address offset: 0x620
Start address for region 2

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW START Start address for region

4413_417 v1.9 364

 Peripherals

6.13.1.25 REGION[2].END
Address offset: 0x624
End address of region 2

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW END End address of region.

6.13.1.26 REGION[3].START
Address offset: 0x630
Start address for region 3

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW START Start address for region

6.13.1.27 REGION[3].END
Address offset: 0x634
End address of region 3

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW END End address of region.

6.13.1.28 PREGION[0].START
Address offset: 0x6C0
Reserved for future use

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R START Reserved for future use

6.13.1.29 PREGION[0].END
Address offset: 0x6C4
Reserved for future use

4413_417 v1.9 365

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R END Reserved for future use

6.13.1.30 PREGION[0].SUBS
Address offset: 0x6C8
Subregions of region 0

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW SR0 Include or exclude subregion 0 in region
Exclude 0 Exclude
Include 1 Include
B RW SR1 Include or exclude subregion 1 in region
Exclude 0 Exclude
Include 1 Include
C RW SR2 Include or exclude subregion 2 in region
Exclude 0 Exclude
Include 1 Include
D RW SR3 Include or exclude subregion 3 in region
Exclude 0 Exclude
Include 1 Include
E RW SR4 Include or exclude subregion 4 in region
Exclude 0 Exclude
Include 1 Include
F RW SR5 Include or exclude subregion 5 in region
Exclude 0 Exclude
Include 1 Include
G RW SR6 Include or exclude subregion 6 in region
Exclude 0 Exclude
Include 1 Include
H RW SR7 Include or exclude subregion 7 in region
Exclude 0 Exclude
Include 1 Include
I RW SR8 Include or exclude subregion 8 in region
Exclude 0 Exclude
Include 1 Include
J RW SR9 Include or exclude subregion 9 in region
Exclude 0 Exclude
Include 1 Include
K RW SR10 Include or exclude subregion 10 in region
Exclude 0 Exclude
Include 1 Include
L RW SR11 Include or exclude subregion 11 in region
Exclude 0 Exclude
Include 1 Include
M RW SR12 Include or exclude subregion 12 in region
Exclude 0 Exclude

4413_417 v1.9 366

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Include 1 Include
N RW SR13 Include or exclude subregion 13 in region
Exclude 0 Exclude
Include 1 Include
O RW SR14 Include or exclude subregion 14 in region
Exclude 0 Exclude
Include 1 Include
P RW SR15 Include or exclude subregion 15 in region
Exclude 0 Exclude
Include 1 Include
Q RW SR16 Include or exclude subregion 16 in region
Exclude 0 Exclude
Include 1 Include
R RW SR17 Include or exclude subregion 17 in region
Exclude 0 Exclude
Include 1 Include
S RW SR18 Include or exclude subregion 18 in region
Exclude 0 Exclude
Include 1 Include
T RW SR19 Include or exclude subregion 19 in region
Exclude 0 Exclude
Include 1 Include
U RW SR20 Include or exclude subregion 20 in region
Exclude 0 Exclude
Include 1 Include
V RW SR21 Include or exclude subregion 21 in region
Exclude 0 Exclude
Include 1 Include
W RW SR22 Include or exclude subregion 22 in region
Exclude 0 Exclude
Include 1 Include
X RW SR23 Include or exclude subregion 23 in region
Exclude 0 Exclude
Include 1 Include
Y RW SR24 Include or exclude subregion 24 in region
Exclude 0 Exclude
Include 1 Include
Z RW SR25 Include or exclude subregion 25 in region
Exclude 0 Exclude
Include 1 Include
a RW SR26 Include or exclude subregion 26 in region
Exclude 0 Exclude
Include 1 Include
b RW SR27 Include or exclude subregion 27 in region
Exclude 0 Exclude
Include 1 Include
c RW SR28 Include or exclude subregion 28 in region
Exclude 0 Exclude
Include 1 Include
d RW SR29 Include or exclude subregion 29 in region

4413_417 v1.9 367

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Exclude 0 Exclude
Include 1 Include
e RW SR30 Include or exclude subregion 30 in region
Exclude 0 Exclude
Include 1 Include
f RW SR31 Include or exclude subregion 31 in region
Exclude 0 Exclude
Include 1 Include

6.13.1.31 PREGION[1].START
Address offset: 0x6D0
Reserved for future use

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R START Reserved for future use

6.13.1.32 PREGION[1].END
Address offset: 0x6D4
Reserved for future use

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R END Reserved for future use

6.13.1.33 PREGION[1].SUBS
Address offset: 0x6D8
Subregions of region 1

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW SR0 Include or exclude subregion 0 in region
Exclude 0 Exclude
Include 1 Include
B RW SR1 Include or exclude subregion 1 in region
Exclude 0 Exclude
Include 1 Include
C RW SR2 Include or exclude subregion 2 in region
Exclude 0 Exclude

4413_417 v1.9 368

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Include 1 Include
D RW SR3 Include or exclude subregion 3 in region
Exclude 0 Exclude
Include 1 Include
E RW SR4 Include or exclude subregion 4 in region
Exclude 0 Exclude
Include 1 Include
F RW SR5 Include or exclude subregion 5 in region
Exclude 0 Exclude
Include 1 Include
G RW SR6 Include or exclude subregion 6 in region
Exclude 0 Exclude
Include 1 Include
H RW SR7 Include or exclude subregion 7 in region
Exclude 0 Exclude
Include 1 Include
I RW SR8 Include or exclude subregion 8 in region
Exclude 0 Exclude
Include 1 Include
J RW SR9 Include or exclude subregion 9 in region
Exclude 0 Exclude
Include 1 Include
K RW SR10 Include or exclude subregion 10 in region
Exclude 0 Exclude
Include 1 Include
L RW SR11 Include or exclude subregion 11 in region
Exclude 0 Exclude
Include 1 Include
M RW SR12 Include or exclude subregion 12 in region
Exclude 0 Exclude
Include 1 Include
N RW SR13 Include or exclude subregion 13 in region
Exclude 0 Exclude
Include 1 Include
O RW SR14 Include or exclude subregion 14 in region
Exclude 0 Exclude
Include 1 Include
P RW SR15 Include or exclude subregion 15 in region
Exclude 0 Exclude
Include 1 Include
Q RW SR16 Include or exclude subregion 16 in region
Exclude 0 Exclude
Include 1 Include
R RW SR17 Include or exclude subregion 17 in region
Exclude 0 Exclude
Include 1 Include
S RW SR18 Include or exclude subregion 18 in region
Exclude 0 Exclude
Include 1 Include
T RW SR19 Include or exclude subregion 19 in region

4413_417 v1.9 369

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Exclude 0 Exclude
Include 1 Include
U RW SR20 Include or exclude subregion 20 in region
Exclude 0 Exclude
Include 1 Include
V RW SR21 Include or exclude subregion 21 in region
Exclude 0 Exclude
Include 1 Include
W RW SR22 Include or exclude subregion 22 in region
Exclude 0 Exclude
Include 1 Include
X RW SR23 Include or exclude subregion 23 in region
Exclude 0 Exclude
Include 1 Include
Y RW SR24 Include or exclude subregion 24 in region
Exclude 0 Exclude
Include 1 Include
Z RW SR25 Include or exclude subregion 25 in region
Exclude 0 Exclude
Include 1 Include
a RW SR26 Include or exclude subregion 26 in region
Exclude 0 Exclude
Include 1 Include
b RW SR27 Include or exclude subregion 27 in region
Exclude 0 Exclude
Include 1 Include
c RW SR28 Include or exclude subregion 28 in region
Exclude 0 Exclude
Include 1 Include
d RW SR29 Include or exclude subregion 29 in region
Exclude 0 Exclude
Include 1 Include
e RW SR30 Include or exclude subregion 30 in region
Exclude 0 Exclude
Include 1 Include
f RW SR31 Include or exclude subregion 31 in region
Exclude 0 Exclude
Include 1 Include

6.14 NFCT — Near field communication tag

The NFCT peripheral is an implementation of an NFC Forum compliant listening device NFC-A.
With appropriate software, the NFCT peripheral can be used as the listening device NFC-A as specified by
the NFC Forum.
Listed here are the main features for the NFCT peripheral:
• NFC-A listen mode operation
• 13.56 MHz input frequency

4413_417 v1.9 370

 Peripherals

• Bit rate 106 kbps

• Wake-on-field low power field detection (SENSE) mode
• Frame assemble and disassemble for the NFC-A frames specified by the NFC Forum
• Programmable frame timing controller
• Integrated automatic collision resolution, cyclic redundancy check (CRC), and parity functions
TASKS_

ACTIVATE
DISABLE
SENSE
STARTTX
ENABLERXDATA
GOIDLE
GOSLEEP
NFCT

Frame
Modulator/ NFC1
EasyDMA assemble/
receiver NFC2
disassemble

EVENTS_
READY
FIELDDETECTED
FIELDLOST
TXFRAMESTART
TXFRAMEEND
RXFRAMESTART
RXFRAMEEND
ERROR
RXERROR
ENDRX
ENDTX
AUTOCOLRESSTARTED
COLLISION
SELECTED
STARTED

Figure 61: NFCT block diagram

6.14.1 Overview
The NFCT peripheral contains a 13.56 MHz AM receiver and a 13.56 MHz load modulator with 106 kbps
data rate as defined by the NFC Forum.

4413_417 v1.9 371

 Peripherals

NFCT
PACKETPTR TXD.FRAMECONFIG
MAXLEN

Frame assemble On-the-air 13.56 MHz NFC-A

SoF/EoF/parity/CRC symbol coder load modulator

STARTTX
Collision ENABLERXDATA Frame timing
EasyDMA Clock recovery
resolution FRAMEDELAYxxx controller
NFC1
NFC2
Frame disassemble On-the-air 13.56 MHz NFC-A
SoF/EoF/parity/CRC symbol decoder receiver

NFCID1_xxx
SENSRES FRAMESTATUS.RX
SELRES Field detector
RXD.FRAMECONFIG

Figure 62: NFCT overview

When transmitting, the frame data will be transferred directly from RAM and transmitted with
configurable frame type and delay timing. The system will be notified by an event whenever a complete
frame is received or sent. The received frames will be automatically disassembled and the data part of the
frame transferred to RAM.
The NFCT peripheral also supports the collision detection and resolution ("anticollision") as defined by the
NFC Forum.
Wake-on-field is supported in SENSE mode while the device is either in System OFF or System ON mode.
When the antenna enters an NFC field, an event will be triggered notifying the system to activate the NFCT
functionality for incoming frames. In System ON, if the energy detected at the antenna increases beyond
a threshold value, the module will generate a FIELDDETECTED event. When the strength of the field no
longer supports NFC communication, the module will generate a FIELDLOST event. For the Low Power
Field Detect threshold values, refer to NFCT Electrical Specification on page 398.
In System OFF, the NFCT Low Power Field Detect function can wake the system up through a reset. See
RESETREAS on page 94 for more information on how to detect a wakeup from NFCT.
If the system is put into System OFF mode while a field is already present, the NFCT Low Power Field
Detect function will wake the system up right away and generate a reset.

Important: As a consequence of a reset, NFCT is disabled, and therefore the reset handler will have
to activate NFCT again and set it up properly.

The HFXO must be running before the NFCT peripheral goes into ACTIVATED state. Note that the NFCT
peripheral calibration is automatically done on ACTIVATE task. The HFXO can be turned off when the NFCT
peripheral goes into SENSE mode. The shortcut FIELDDETECTED_ACTIVATE can be used when the HFXO is
already running while in SENSE mode.
Outgoing data will be collected from RAM with the EasyDMA function and assembled according to
theTXD.FRAMECONFIG on page 395 register. Incoming data will be disassembled according to the
RXD.FRAMECONFIG register and the data section in the frame will be written to RAM via the EasyDMA
function.

4413_417 v1.9 372

 Peripherals

The NFCT peripheral includes a frame timing controller that can be used to accurately control the inter-
frame delay between the incoming frame and a corresponding outgoing frame. It also includes optional
CRC functionality.

6.14.2 Operating states

Tasks and events are used to control the operating state of the peripheral. The module can change state by
triggering a task, or when specific operations are finalized. Events and tasks allow software to keep track of
and change the current state.
See NFCT block diagram on page 371 and NFCT state diagram, automatic collision resolution enabled on
page 373 for more information. See NFC Forum, NFC Activity Technical Specification for description on
NFCT operating states.
Activated

GOIDLE NFC (OTHER)

/ COLLISION

DISABLE
NFC (ALL_REQ)
DISABLE / AUTOCOLRESSTARTED
/ READY / SELECTED
ACTIVATE IDLERU IDLE READY_A

NFC (SENS_REQ)
/ AUTOCOLRESSTARTED

NFC (OTHER)
/ COLLISION
GOSLEEP / SELECTED
SLEEP_A READY_A*
DISABLE SENSE NFC (ALL_REQ)
NFC (SLP_REQ)
/ AUTOCOLRESSTARTED
ACTIVE_A

ENABLERXDATA STARTTX
SENSE
SENSE_FIELD

STARTTX / TXFRAMEEND
RECEIVE TRANSMIT

ACTIVATE / RXFRAMEEND / RXERROR

Figure 63: NFCT state diagram, automatic collision resolution enabled

Activated

DISABLE
DISABLE
ACTIVATE IDLERU

/ READY

DISABLE SENSE

ACTIVE_A

ENABLERXDATA STARTTX
SENSE
SENSE_FIELD

STARTTX /TXFRAMEEND
RECEIVE TRANSMIT

ACTIVATE / RXERROR
/RXFRAMEEND

Figure 64: NFCT state diagram, automatic collision resolution disabled

4413_417 v1.9 373

 Peripherals

Important:
• FIELDLOST event is not generated in SENSE mode.
• Sending SENSE task while field is still present does not generate FIELDDETECTED event.
• If the FIELDDETECTED event is cleared before sending the ACTIVATE task, then the
FIELDDETECTED event shows up again after sending the ACTIVATE task. The shortcut
FIELDDETECTED_ACTIVATE can be used to avoid this condition.

6.14.3 Pin configuration

NFCT uses two pins to connect the antenna and these pins are shared with GPIOs.
The PROTECT field in the NFCPINS register in UICR defines the usage of these pins and their protection
level against excessive voltages. The content of the NFCPINS register is reloaded at every reset. See Pin
assignments on page 845 for the pins used by the NFCT peripheral.
When NFCPINS.PROTECT=NFC, a protection circuit will be enabled on the dedicated pins, preventing the
chip from being damaged in the presence of a strong NFC field. The protection circuit will short the two
pins together if voltage difference exceeds approximately 2V. The GPIO function on those pins will also be
disabled.
When NFCPINS.PROTECT=Disabled, the device will not be protected against strong NFC field damages
caught by a connected NFCT antenna, and the NFCT peripheral will not operate as expected, as it will
never leave the DISABLE state.
The pins dedicated to the NFCT antenna function will have some limitation when the pins are configured
for normal GPIO operation. The pin capacitance will be higher on those (refer to CPAD_NFC in the Electrical
Specification of GPIO — General purpose input/output on page 240), and some increased leakage
current between the two pins is to be expected if they are used in GPIO mode, and are driven to different
logical values. To save power, the two pins should always be set to the same logical value whenever
entering one of the device power saving modes. For details, refer to INFC_LEAK in the Electrical Specification
of GPIO — General purpose input/output on page 240.

6.14.4 EasyDMA
The NFCT peripheral implements EasyDMA for reading and writing of data packets from and to the Data
RAM.
The NFCT EasyDMA utilizes a pointer called PACKETPTR on page 394 for receiving and transmitting
packets.
The NFCT peripheral uses EasyDMA to read or write RAM, but not both at the same time. The event
RXFRAMESTART indicates that the EasyDMA has started writing to the RAM for a receive frame and the
event RXFRAMEND indicates that the EasyDMA has completed writing to the RAM. Similarly, the event
TXFRAMESTART indicates that the EasyDMA has started reading from the RAM for a transmit frame and
the event TXFRAMEND indicates that the EasyDMA has completed reading from the RAM. If a transmit
and a receive operation is issued at the same time, the transmit operation would be prioritized.
Starting a transmit operation while the EasyDMA is writing a receive frame to the RAM will result in
unpredictable behavior. Starting an EasyDMA operation when there is an ongoing EasyDMA operation may
result in unpredictable behavior. It is recommended to wait for the TXFRAMEEND or RXFRAMEEND event
for the ongoing transmit or receive before starting a new receive or transmit operation.
The MAXLEN on page 394 register determines the maximum number of bytes that can be read from
or written to the RAM. This feature can be used to ensure that the NFCT peripheral does not overwrite,
or read beyond, the RAM assigned to a packet. Note that if the RXD.AMOUNT or TXD.AMOUNT register
indicates longer data packets than set in MAXLEN, the frames sent to or received from the physical layer

4413_417 v1.9 374

 Peripherals

will be incomplete. In that situation, in RX, the OVERRUN bit in the FRAMESTATUS.RX register will be set
and an RXERROR event will be triggered.

Important: The RXD.AMOUNT and TXD.AMOUNT define a frame length in bytes and bits excluding
start of frame (SoF), end of frame (EoF), and parity, but including CRC for RXD.AMOUNT only. Make
sure to take potential additional bits into account when setting MAXLEN.

Only sending task ENABLERXDATA ensures that a new value in PACKETPTR pointing to the RX buffer in Data
RAM is taken into account.
If PACKETPTR is not pointing to the Data RAM region, an EasyDMA transfer may result in a hard fault or
RAM corruption. For more information about the different memory regions, see Chapter Memory on page
21.
The NFCT peripherals normally do alternative receive and transmit frames. Therefore, to prepare for the
next frame, the PACKETPTR, MAXLEN, TXD.FRAMECONFIG and TXD.AMOUNT can be updated while the
receive is in progress, and, similarly, the PACKETPTR, MAXLEN and RXD.FRAMECONFIG can be updated
while the transmit is in progress. They can be updated and prepared for the next NFC frame immediately
after the STARTED event of the current frame has been received. Updating the TXD.FRAMECONFIG and
TXD.AMOUNT during the current transmit frame or updating RXD.FRAMECONFIG during current receive
frame may cause unpredictable behaviour.
In accordance with NFC Forum, NFC Digital Protocol Technical Specification, the least significant bit (LSB)
from the least significant byte (LSByte) is sent on air first. The bytes are stored in increasing order, starting
at the lowest address in the EasyDMA buffer in RAM.

6.14.5 Frame assembler

The NFCT peripheral implements a frame assembler in hardware.
When the NFCT peripheral is in the ACTIVE_A state, the software can decide to enter RX or TX mode. For
RX, see Frame disassembler on page 376. For TX, the software must indicate the address of the source
buffer in Data RAM and its size through programming the PACKETPTR and MAXLEN registers respectively,
then issuing a STARTTX task.
MAXLEN must be set so that it matches the size of the frame to be sent.
The STARTED event indicates that the PACKETPTR and MAXLEN registers have been captured by the frame
assembler EasyDMA.
When asserting the STARTTX task, the frame assembler module will start reading
TXD.AMOUNT.TXDATABYTES bytes (plus one additional byte if TXD.AMOUNT.TXDATABITS > 0) from the
RAM position set by the PACKETPTR.
The NFCT peripheral transmits the data as read from RAM, adding framing and the CRC calculated on
the fly if set in TXD.FRAMECONFIG. The NFCT peripheral will take (8*TXD.AMOUNT.TXDATABYTES +
TXD.AMOUNT.TXDATABITS) bits and assemble a frame according to the settings in TXD.FRAMECONFIG.
Both short frames, standard frames, and bit-oriented SDD frames as specified in the NFC Forum, NFC
Digital Protocol Technical Specification can be assembled by the correct setting of the TXD.FRAMECONFIG
register.
The bytes will be transmitted on air in the same order as they are read from RAM with a rising bit order
within each byte, least significant bit (LSB) first. That is, b0 will be transmitted on air before b1, and so
on. The bits read from RAM will be coded into symbols as defined in the NFC Forum, NFC Digital Protocol
Technical Specification.

4413_417 v1.9 375

 Peripherals

Important: Some NFC Forum documents, such as NFC Forum, NFC Digital Protocol Technical
Specification, define bit numbering in a byte from b1 (LSB) to b8 (most significant bit (MSB)),
while most other technical documents from the NFC Forum, and also the Nordic Semiconductor
documentation, traditionally number them from b0 to b7. The present document uses the b0–
b7 numbering scheme. Be aware of this when comparing the NFC Forum, NFC Digital Protocol
Technical Specification to others.

The frame assembler can be configured in TXD.FRAMECONFIG to add SoF symbol, calculate and add parity
bits, and calculate and add CRC to the data read from RAM when assembling the frame. The total frame
will then be longer than what is defined by TXD.AMOUNT.TXDATABYTES. TXDATABITS. DISCARDMODE will
select if the first bits in the first byte read from RAM or the last bits in the last byte read from RAM will
be discarded if TXD.AMOUNT.TXDATABITS are not equal to zero. Note that if TXD.FRAMECONFIG.PARITY
= Parity and TXD.FRAMECONFIG.DISCARDMODE=DiscardStart, a parity bit will be included after the non-
complete first byte. No parity will be added after a non-complete last byte.
The frame assemble operation is illustrated in Frame assemble illustration on page 376 for different
settings in TXD.FRAMECONFIG. All shaded bit fields are added by the frame assembler. Some of these bits
are optional and appearances are configured in TXD.FRAMECONFIG. Note that the frames illustrated do
not necessarily comply with the NFC specification. The figure is only to illustrate the behavior of the NFCT
peripheral.
Data from RAM
Byte 1: PACKETPTR + 0 Byte 2: PACKETPTR + 1 Byte (TXDATABYTES) Byte (TXDATABYTES + 1)
b0 .. b7 b0 .. b7 b0 .. b7 b0 .. b7
(only if TXDATABITS > 0)

Frame on air
PARITY = Parity
TXDATABITS = 0
CRCMODETX = CRC16TX

Byte 1 Byte 2 Byte (TXDATABYTES)

SoF b0 .. b7 P b0 .. b7 P b0 .. b7 P CRC 1 (8 bit) P CRC 2 (8 bit) P EoF

PARITY = Parity
TXDATABITS = 4
CRCMODETX = NoCRCTX
DISCARDMODE = DiscardStart

Byte 1 Byte 2 Byte (TXDATABYTES) Byte (TXDATABYTES + 1)

SoF b4 .. b7 P b0 .. b7 P b0 .. b7 P b0 .. b7 P EoF

PARITY = Parity
TXDATABITS = 0
CRCMODETX = NoCRCTX

Byte 1 Byte TXDATABYTES

SoF b0 .. b7 P b0 .. b7 P EoF

Figure 65: Frame assemble illustration

The accurate timing for transmitting the frame on air is set using the frame timing controller settings.

6.14.6 Frame disassembler

The NFCT peripheral implements a frame disassembler in hardware.
When the NFCT peripheral is in the ACTIVE_A state, the software can decide to enter RX or TX mode. For
TX, see Frame assembler on page 375. For RX, the software must indicate the address and size of the
destination buffer in Data RAM through programming the PACKETPTR and MAXLEN registers before issuing
an ENABLERXDATA task.
The STARTED event indicates that the PACKETPTR and MAXLEN registers have been captured by the frame
disassembler EasyDMA.
When an incoming frame starts, the RXFRAMESTART event will get issued and data will be written to the
buffer in Data RAM. The frame disassembler will verify and remove any parity bits, start of frame (SoF) and

4413_417 v1.9 376

 Peripherals

end of frame (EoF) symbols on the fly based on RXD.FRAMECONFIG register configuration. It will, however,
verify and transfer the CRC bytes into RAM, if the CRC is enabled through RXD.FRAMECONFIG.
When an EoF symbol is detected, the NFCT peripheral will assert the RXFRAMEEND event and write the
RXD.AMOUNT register to indicate numbers of received bytes and bits in the data packet. The module does
not interpret the content of the data received from the remote NFC device, except for SoF, EoF, parity, and
CRC checking, as described above. The frame disassemble operation is illustrated below.
Frame on air
PARITY = Parity
RXDATABITS = 0
CRCMODERX = CRC16RX

Byte 1 Byte 2 Byte (RXDATABYTES)

SoF b0 .. b7 P b0 .. b7 P b0 .. b7 P CRC 1 (8 bit) P CRC 2 (8 bit) P EoF

PARITY = Parity
CRCMODERX = NoCRCTR
RXDATABITS = 4

Byte 1 Byte 2 Byte (RXDATABYTES) Byte (RXDATABYTES + 1)

SoF b0 .. b7 P b0 .. b7 P b0 .. b7 P b4 .. b7 EoF

PARITY = NoParity
CRCMODERX = NoCRCRX
RXDATABITS = 0

Byte 1 Byte 2 Byte RXDATABYTES

SoF b0 .. b7 b0 .. b7 b0 .. b7 b0 .. b7 EoF

Data to RAM
Byte 1: PACKETPTR + 0 Byte 2: PACKETPTR + 1 Byte (RXDATABYTES) Byte (RXDATABYTES + 1)
b0 .. b7 b0 .. b7 b0 .. b7 b0 .. b7
(only if RXDATABITS > 0)

Figure 66: Frame disassemble illustration

Per NFC specification, the time between EoF to the next SoF can be as short as 86 μs, and thefore care
must be taken that PACKETPTR and MAXLEN are ready and ENABLERXDATA is issued on time after the end
of previous frame. The use of a PPI shortcut from TXFRAMEEND to ENABLERXDATA is recommended.

6.14.7 Frame timing controller

The NFCT peripheral includes a frame timing controller that continuously keeps track of the number of the
13.56 MHz RF carrier clock periods since the end of the EoF of the last received frame.
The NFCT peripheral can be programmed to send a responding frame within a time window or at an exact
count of RF carrier periods. In case of FRAMEDELAYMODE = Window, a STARTTX task triggered before the
frame timing controller counter is equal to FRAMEDELAYMIN will force the transmission to halt until the
counter is equal to FRAMEDELAYMIN. If the counter is within FRAMEDELAYMIN and FRAMEDELAYMAX
when the STARTTX task is triggered, the NFCT peripheral will start the transmission straight away. In case
of FRAMEDELAYMODE = ExactVal, a STARTTX task triggered before the frame delay counter is equal to
FRAMEDELAYMAX will halt the actual transmission start until the counter is equal to FRAMEDELAYMAX.
In case of FRAMEDELAYMODE = WindowGrid, the behaviour is similar to the FRAMEDELAYMODE =
Window, but the actual transmission between FRAMEDELAYMIN and FRAMEDELAYMAX starts on a bit grid
as defined for NFC-A Listen frames (slot duration of 128 RF carrier periods).
An ERROR event (with FRAMEDELAYTIMEOUT cause in ERRORSTATUS) will be asserted if the frame timing
controller counter reaches FRAMEDELAYMAX without any STARTTX task triggered. This may happen
even when the response is not required as per NFC Forum, NFC Digital Protocol Technical Specification.
Any commands handled by the automatic collision resolution that don't involve a response being
generated may also result in an ERROR event (with FRAMEDELAYTIMEOUT cause in ERRORSTATUS).
The FRAMEDELAYMIN and FRAMEDELAYMAX values shall only be updated before the STARTTX task is
triggered. Failing to do so may cause unpredictable behaviour.

4413_417 v1.9 377

 Peripherals

The frame timing controller operation is illustrated in Frame timing controller

(FRAMEDELAYMODE=Window) on page 378. The frame timing controller automatically adjusts the
frame timing counter based on the last received data bit according to NFC-A technology in the NFC Forum,
NFC Digital Protocol Technical Specification.

Receive Transmit
Last data bit EoF

Logic ‘0’ Subcarrier continues in the 3 cases below

Logic ‘1’ 20/fc FRAMEDELAYMAX

84/fc FRAMEDELAYMIN
Before Min STARTTX task

SoF
Subcarrier modulation

Between Min and Max STARTTX task

SoF
Subcarrier modulation

After Max (or missing) STARTTX task

Subcarrier modulation

ERROR event

Figure 67: Frame timing controller (FRAMEDELAYMODE=Window)

6.14.8 Collision resolution

The NFCT peripheral implements an automatic collision resolution function as defined by the NFC Forum.
Automatic collision resolution is enabled by default, and it is recommended that the feature is used since
it is power efficient and reduces the complexity of software handling the collision resolution sequence.
This feature can be disabled through the MODE field in the AUTOCOLRESCONFIG register. When the
automatic collision resolution is disabled, all commands will be sent over EasyDMA as defined in frame
disassembler.
The SENSRES and SELRES registers need to be programmed upfront in order for the collision resolution to
behave correctly. Depending on the NFCIDSIZE field in SENSRES, the following registers also need to be
programmed upfront:
• NFCID1_LAST if NFCID1SIZE=NFCID1Single (ID = 4 bytes);
• NFCID1_2ND_LAST and NFCID1_LAST if NFCID1SIZE=NFCID1Double (ID = 7 bytes);
• NFCID1_3RD_LAST, NFCID1_2ND_LAST and NFCID1_LAST if NFCID1SIZE=NFCID1Triple (ID = 10 bytes);
A pre-defined set of registers, NFC.TAGHEADER0..3, containing a valid NFCID1 value, is available in FICR
and can be used by software to populate the NFCID1_3RD_LAST, NFCID1_2ND_LAST, and NFCID1_LAST
registers.
NFCID1 byte allocation (top sent first on air) on page 379 explains the position of the ID bytes in
NFCID1_3RD_LAST, NFCID1_2ND_LAST, and NFCID1_LAST, depending on the ID size, and as compared to
the definition used in the NFC Forum, NFC Digital Protocol Technical Specification.

4413_417 v1.9 378

 Peripherals

ID = 4 bytes ID = 7 bytes ID = 10 bytes

NFCID1_Q nfcid10
NFCID1_R nfcid11
NFCID1_S nfcid12
NFCID1_T nfcid10 nfcid13
NFCID1_U nfcid11 nfcid14
NFCID1_V nfcid12 nfcid15
NFCID1_W nfcid10 nfcid13 nfcid16
NFCID1_X nfcid11 nfcid14 nfcid17
NFCID1_Y nfcid12 nfcid15 nfcid18
NFCID1_Z nfcid13 nfcid16 nfcid19

Table 25: NFCID1 byte allocation (top sent first on air)

The hardware implementation can handle the states from IDLE to ACTIVE_A automatically as defined
in the NFC Forum, NFC Activity Technical Specification, and the other states are to be handled by
software. The software keeps track of the state through events. The collision resolution will trigger
an AUTOCOLRESSTARTED event when it has started. Reaching the ACTIVE_A state is indicated by the
SELECTED event.
If collision resolution fails, a COLLISION event is triggered. Note that errors occurring during automatic
collision resolution may also cause ERROR and/or RXERROR events to be generated. Other events may also
get generated. It is recommended that the software ignores any event except COLLISION, SELECTED and
FIELDLOST during automatic collision resolution. Software shall also make sure that any unwanted SHORT
or PPI shortcut is disabled during automatic collision resolution.
The automatic collision resolution will be restarted, if the packets are received with CRC or parity errors
while in ACTIVE_A state. The automatic collision resolution feature can be disabled while in ACTIVE_A
state to avoid this.
The SLP_REQ is automatically handled by the NFCT peripheral when the automatic collision resolution is
enabled. However, this results in an ERROR event (with FRAMEDELAYTIMEOUT cause in ERRORSTATUS)
since the SLP_REQ has no response. This error must be ignored until the SELECTED event is triggered and
this error should be cleared by the software when the SELECTED event is triggered.

6.14.9 Antenna interface

In ACTIVATED state, an amplitude regulator will adjust the voltage swing on the antenna pins to a value
that is within the Vswing limit.
Refer to NFCT Electrical Specification on page 398.

6.14.10 NFCT antenna recommendations

The NFCT antenna coil must be connected differential between NFC1 and NFC2 pins of the device.
Two external capacitors should be used to tune the resonance of the antenna circuit to 13.56 MHz.

4413_417 v1.9 379

 Peripherals

Cp1 Ctune1 Cint1

NFC1

ANTENNA Lant Rin

NFC2

Cp2 Ctune2 Cint2

Figure 68: NFCT antenna recommendations

The required tuning capacitor value is given by the below equations:

An antenna inductance of Lant = 2 μH will give tuning capacitors in the range of 130 pF on each pin. The
total capacitance on NFC1 and NFC2 must be matched.

6.14.11 Battery protection

If the antenna is exposed to a strong NFC field, current may flow in the opposite direction on the supply
due to parasitic diodes and ESD structures.
If the battery used does not tolerate return current, a series diode must be placed between the battery
and the device in order to protect the battery.

6.14.12 References
NFC Forum, NFC Analog Specification version 1.0, www.nfc-forum.org
NFC Forum, NFC Digital Protocol Technical Specification version 1.1, www.nfc-forum.org
NFC Forum, NFC Activity Technical Specification version 1.1, www.nfc-forum.org

6.14.13 Registers
Instances

Instance Base address Description

NFCT 0x40005000 Near field communication tag

4413_417 v1.9 380

 Peripherals

Register overview

Register Offset Description

TASKS_ACTIVATE 0x000 Activate NFCT peripheral for incoming and outgoing frames, change state to activated
TASKS_DISABLE 0x004 Disable NFCT peripheral
TASKS_SENSE 0x008 Enable NFC sense field mode, change state to sense mode
TASKS_STARTTX 0x00C Start transmission of an outgoing frame, change state to transmit
TASKS_ENABLERXDATA 0x01C Initializes the EasyDMA for receive.
TASKS_GOIDLE 0x024 Force state machine to IDLE state
TASKS_GOSLEEP 0x028 Force state machine to SLEEP_A state
EVENTS_READY 0x100 The NFCT peripheral is ready to receive and send frames
EVENTS_FIELDDETECTED 0x104 Remote NFC field detected
EVENTS_FIELDLOST 0x108 Remote NFC field lost
EVENTS_TXFRAMESTART 0x10C Marks the start of the first symbol of a transmitted frame
EVENTS_TXFRAMEEND 0x110 Marks the end of the last transmitted on-air symbol of a frame
EVENTS_RXFRAMESTART 0x114 Marks the end of the first symbol of a received frame
EVENTS_RXFRAMEEND 0x118 Received data has been checked (CRC, parity) and transferred to RAM, and EasyDMA has ended
accessing the RX buffer
EVENTS_ERROR 0x11C NFC error reported. The ERRORSTATUS register contains details on the source of the error.
EVENTS_RXERROR 0x128 NFC RX frame error reported. The FRAMESTATUS.RX register contains details on the source of the
error.
EVENTS_ENDRX 0x12C RX buffer (as defined by PACKETPTR and MAXLEN) in Data RAM full.
EVENTS_ENDTX 0x130 Transmission of data in RAM has ended, and EasyDMA has ended accessing the TX buffer
EVENTS_AUTOCOLRESSTARTED 0x138 Auto collision resolution process has started
EVENTS_COLLISION 0x148 NFC auto collision resolution error reported.
EVENTS_SELECTED 0x14C NFC auto collision resolution successfully completed
EVENTS_STARTED 0x150 EasyDMA is ready to receive or send frames.
SHORTS 0x200 Shortcuts between local events and tasks
INTEN 0x300 Enable or disable interrupt
INTENSET 0x304 Enable interrupt
INTENCLR 0x308 Disable interrupt
ERRORSTATUS 0x404 NFC Error Status register
FRAMESTATUS.RX 0x40C Result of last incoming frame
NFCTAGSTATE 0x410 NfcTag state register
SLEEPSTATE 0x420 Sleep state during automatic collision resolution
FIELDPRESENT 0x43C Indicates the presence or not of a valid field
FRAMEDELAYMIN 0x504 Minimum frame delay
FRAMEDELAYMAX 0x508 Maximum frame delay
FRAMEDELAYMODE 0x50C Configuration register for the Frame Delay Timer
PACKETPTR 0x510 Packet pointer for TXD and RXD data storage in Data RAM
MAXLEN 0x514 Size of the RAM buffer allocated to TXD and RXD data storage each
TXD.FRAMECONFIG 0x518 Configuration of outgoing frames
TXD.AMOUNT 0x51C Size of outgoing frame
RXD.FRAMECONFIG 0x520 Configuration of incoming frames
RXD.AMOUNT 0x524 Size of last incoming frame
NFCID1_LAST 0x590 Last NFCID1 part (4, 7 or 10 bytes ID)
NFCID1_2ND_LAST 0x594 Second last NFCID1 part (7 or 10 bytes ID)
NFCID1_3RD_LAST 0x598 Third last NFCID1 part (10 bytes ID)
AUTOCOLRESCONFIG 0x59C Controls the auto collision resolution function. This setting must be done before the NFCT peripheral
is activated.
SENSRES 0x5A0 NFC-A SENS_RES auto-response settings
SELRES 0x5A4 NFC-A SEL_RES auto-response settings

4413_417 v1.9 381

 Peripherals

6.14.13.1 TASKS_ACTIVATE
Address offset: 0x000
Activate NFCT peripheral for incoming and outgoing frames, change state to activated

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_ACTIVATE Activate NFCT peripheral for incoming and outgoing frames, change state to
activated
Trigger 1 Trigger task

6.14.13.2 TASKS_DISABLE
Address offset: 0x004
Disable NFCT peripheral

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_DISABLE Disable NFCT peripheral
Trigger 1 Trigger task

6.14.13.3 TASKS_SENSE
Address offset: 0x008
Enable NFC sense field mode, change state to sense mode

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_SENSE Enable NFC sense field mode, change state to sense mode
Trigger 1 Trigger task

6.14.13.4 TASKS_STARTTX
Address offset: 0x00C
Start transmission of an outgoing frame, change state to transmit

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STARTTX Start transmission of an outgoing frame, change state to transmit
Trigger 1 Trigger task

4413_417 v1.9 382

 Peripherals

6.14.13.5 TASKS_ENABLERXDATA
Address offset: 0x01C
Initializes the EasyDMA for receive.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_ENABLERXDATA Initializes the EasyDMA for receive.
Trigger 1 Trigger task

6.14.13.6 TASKS_GOIDLE
Address offset: 0x024
Force state machine to IDLE state

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_GOIDLE Force state machine to IDLE state
Trigger 1 Trigger task

6.14.13.7 TASKS_GOSLEEP
Address offset: 0x028
Force state machine to SLEEP_A state

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_GOSLEEP Force state machine to SLEEP_A state
Trigger 1 Trigger task

6.14.13.8 EVENTS_READY
Address offset: 0x100
The NFCT peripheral is ready to receive and send frames

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_READY The NFCT peripheral is ready to receive and send frames
NotGenerated 0 Event not generated
Generated 1 Event generated

4413_417 v1.9 383

 Peripherals

6.14.13.9 EVENTS_FIELDDETECTED
Address offset: 0x104
Remote NFC field detected

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_FIELDDETECTED Remote NFC field detected
NotGenerated 0 Event not generated
Generated 1 Event generated

6.14.13.10 EVENTS_FIELDLOST
Address offset: 0x108
Remote NFC field lost

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_FIELDLOST Remote NFC field lost
NotGenerated 0 Event not generated
Generated 1 Event generated

6.14.13.11 EVENTS_TXFRAMESTART
Address offset: 0x10C
Marks the start of the first symbol of a transmitted frame

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_TXFRAMESTART Marks the start of the first symbol of a transmitted frame
NotGenerated 0 Event not generated
Generated 1 Event generated

6.14.13.12 EVENTS_TXFRAMEEND
Address offset: 0x110
Marks the end of the last transmitted on-air symbol of a frame

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_TXFRAMEEND Marks the end of the last transmitted on-air symbol of a frame
NotGenerated 0 Event not generated
Generated 1 Event generated

4413_417 v1.9 384

 Peripherals

6.14.13.13 EVENTS_RXFRAMESTART
Address offset: 0x114
Marks the end of the first symbol of a received frame

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_RXFRAMESTART Marks the end of the first symbol of a received frame
NotGenerated 0 Event not generated
Generated 1 Event generated

6.14.13.14 EVENTS_RXFRAMEEND
Address offset: 0x118
Received data has been checked (CRC, parity) and transferred to RAM, and EasyDMA has ended accessing
the RX buffer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_RXFRAMEEND Received data has been checked (CRC, parity) and transferred to RAM, and
EasyDMA has ended accessing the RX buffer
NotGenerated 0 Event not generated
Generated 1 Event generated

6.14.13.15 EVENTS_ERROR
Address offset: 0x11C
NFC error reported. The ERRORSTATUS register contains details on the source of the error.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_ERROR NFC error reported. The ERRORSTATUS register contains details on the
source of the error.
NotGenerated 0 Event not generated
Generated 1 Event generated

6.14.13.16 EVENTS_RXERROR
Address offset: 0x128
NFC RX frame error reported. The FRAMESTATUS.RX register contains details on the source of the error.

4413_417 v1.9 385

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_RXERROR NFC RX frame error reported. The FRAMESTATUS.RX register contains details
on the source of the error.
NotGenerated 0 Event not generated
Generated 1 Event generated

6.14.13.17 EVENTS_ENDRX
Address offset: 0x12C
RX buffer (as defined by PACKETPTR and MAXLEN) in Data RAM full.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_ENDRX RX buffer (as defined by PACKETPTR and MAXLEN) in Data RAM full.
NotGenerated 0 Event not generated
Generated 1 Event generated

6.14.13.18 EVENTS_ENDTX
Address offset: 0x130
Transmission of data in RAM has ended, and EasyDMA has ended accessing the TX buffer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_ENDTX Transmission of data in RAM has ended, and EasyDMA has ended accessing
the TX buffer
NotGenerated 0 Event not generated
Generated 1 Event generated

6.14.13.19 EVENTS_AUTOCOLRESSTARTED
Address offset: 0x138
Auto collision resolution process has started

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_AUTOCOLRESSTARTED Auto collision resolution process has started
NotGenerated 0 Event not generated
Generated 1 Event generated

6.14.13.20 EVENTS_COLLISION
Address offset: 0x148

4413_417 v1.9 386

 Peripherals

NFC auto collision resolution error reported.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A
Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_COLLISION NFC auto collision resolution error reported.
NotGenerated 0 Event not generated
Generated 1 Event generated

6.14.13.21 EVENTS_SELECTED
Address offset: 0x14C
NFC auto collision resolution successfully completed

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_SELECTED NFC auto collision resolution successfully completed
NotGenerated 0 Event not generated
Generated 1 Event generated

6.14.13.22 EVENTS_STARTED
Address offset: 0x150
EasyDMA is ready to receive or send frames.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_STARTED EasyDMA is ready to receive or send frames.
NotGenerated 0 Event not generated
Generated 1 Event generated

6.14.13.23 SHORTS
Address offset: 0x200
Shortcuts between local events and tasks

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID F B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW FIELDDETECTED_ACTIVATE Shortcut between event FIELDDETECTED and task ACTIVATE
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
B RW FIELDLOST_SENSE Shortcut between event FIELDLOST and task SENSE
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut

4413_417 v1.9 387

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID F B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
F RW TXFRAMEEND_ENABLERXDATA Shortcut between event TXFRAMEEND and task ENABLERXDATA
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut

6.14.13.24 INTEN
Address offset: 0x300
Enable or disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID T S R N M L K H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW READY Enable or disable interrupt for event READY
Disabled 0 Disable
Enabled 1 Enable
B RW FIELDDETECTED Enable or disable interrupt for event FIELDDETECTED
Disabled 0 Disable
Enabled 1 Enable
C RW FIELDLOST Enable or disable interrupt for event FIELDLOST
Disabled 0 Disable
Enabled 1 Enable
D RW TXFRAMESTART Enable or disable interrupt for event TXFRAMESTART
Disabled 0 Disable
Enabled 1 Enable
E RW TXFRAMEEND Enable or disable interrupt for event TXFRAMEEND
Disabled 0 Disable
Enabled 1 Enable
F RW RXFRAMESTART Enable or disable interrupt for event RXFRAMESTART
Disabled 0 Disable
Enabled 1 Enable
G RW RXFRAMEEND Enable or disable interrupt for event RXFRAMEEND
Disabled 0 Disable
Enabled 1 Enable
H RW ERROR Enable or disable interrupt for event ERROR
Disabled 0 Disable
Enabled 1 Enable
K RW RXERROR Enable or disable interrupt for event RXERROR
Disabled 0 Disable
Enabled 1 Enable
L RW ENDRX Enable or disable interrupt for event ENDRX
Disabled 0 Disable
Enabled 1 Enable
M RW ENDTX Enable or disable interrupt for event ENDTX
Disabled 0 Disable
Enabled 1 Enable
N RW AUTOCOLRESSTARTED Enable or disable interrupt for event AUTOCOLRESSTARTED
Disabled 0 Disable
Enabled 1 Enable

4413_417 v1.9 388

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID T S R N M L K H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
R RW COLLISION Enable or disable interrupt for event COLLISION
Disabled 0 Disable
Enabled 1 Enable
S RW SELECTED Enable or disable interrupt for event SELECTED
Disabled 0 Disable
Enabled 1 Enable
T RW STARTED Enable or disable interrupt for event STARTED
Disabled 0 Disable
Enabled 1 Enable

6.14.13.25 INTENSET
Address offset: 0x304
Enable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID T S R N M L K H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW READY Write '1' to enable interrupt for event READY
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW FIELDDETECTED Write '1' to enable interrupt for event FIELDDETECTED
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW FIELDLOST Write '1' to enable interrupt for event FIELDLOST
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
D RW TXFRAMESTART Write '1' to enable interrupt for event TXFRAMESTART
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
E RW TXFRAMEEND Write '1' to enable interrupt for event TXFRAMEEND
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
F RW RXFRAMESTART Write '1' to enable interrupt for event RXFRAMESTART
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
G RW RXFRAMEEND Write '1' to enable interrupt for event RXFRAMEEND
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
H RW ERROR Write '1' to enable interrupt for event ERROR
Set 1 Enable

4413_417 v1.9 389

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID T S R N M L K H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
K RW RXERROR Write '1' to enable interrupt for event RXERROR
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
L RW ENDRX Write '1' to enable interrupt for event ENDRX
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
M RW ENDTX Write '1' to enable interrupt for event ENDTX
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
N RW AUTOCOLRESSTARTED Write '1' to enable interrupt for event AUTOCOLRESSTARTED
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
R RW COLLISION Write '1' to enable interrupt for event COLLISION
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
S RW SELECTED Write '1' to enable interrupt for event SELECTED
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
T RW STARTED Write '1' to enable interrupt for event STARTED
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.14.13.26 INTENCLR
Address offset: 0x308
Disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID T S R N M L K H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW READY Write '1' to disable interrupt for event READY
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW FIELDDETECTED Write '1' to disable interrupt for event FIELDDETECTED
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW FIELDLOST Write '1' to disable interrupt for event FIELDLOST

4413_417 v1.9 390

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID T S R N M L K H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
D RW TXFRAMESTART Write '1' to disable interrupt for event TXFRAMESTART
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
E RW TXFRAMEEND Write '1' to disable interrupt for event TXFRAMEEND
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
F RW RXFRAMESTART Write '1' to disable interrupt for event RXFRAMESTART
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
G RW RXFRAMEEND Write '1' to disable interrupt for event RXFRAMEEND
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
H RW ERROR Write '1' to disable interrupt for event ERROR
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
K RW RXERROR Write '1' to disable interrupt for event RXERROR
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
L RW ENDRX Write '1' to disable interrupt for event ENDRX
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
M RW ENDTX Write '1' to disable interrupt for event ENDTX
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
N RW AUTOCOLRESSTARTED Write '1' to disable interrupt for event AUTOCOLRESSTARTED
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
R RW COLLISION Write '1' to disable interrupt for event COLLISION
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
S RW SELECTED Write '1' to disable interrupt for event SELECTED
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
T RW STARTED Write '1' to disable interrupt for event STARTED
Clear 1 Disable
Disabled 0 Read: Disabled

4413_417 v1.9 391

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID T S R N M L K H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Enabled 1 Read: Enabled

6.14.13.27 ERRORSTATUS
Address offset: 0x404
NFC Error Status register

Note: Write a bit to '1' to clear it. Writing '0' has no effect.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW FRAMEDELAYTIMEOUT No STARTTX task triggered before expiration of the time set in
W1C FRAMEDELAYMAX

6.14.13.28 FRAMESTATUS.RX
Address offset: 0x40C
Result of last incoming frame

Note: Write a bit to '1' to clear it. Writing '0' has no effect.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW CRCERROR No valid end of frame (EoF) detected
W1C
CRCCorrect 0 Valid CRC detected
CRCError 1 CRC received does not match local check
B RW PARITYSTATUS Parity status of received frame
W1C
ParityOK 0 Frame received with parity OK
ParityError 1 Frame received with parity error
C RW OVERRUN Overrun detected
W1C
NoOverrun 0 No overrun detected
Overrun 1 Overrun error

6.14.13.29 NFCTAGSTATE
Address offset: 0x410
NfcTag state register

4413_417 v1.9 392

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R NFCTAGSTATE NfcTag state
Disabled 0 Disabled or sense
RampUp 2 RampUp
Idle 3 Idle
Receive 4 Receive
FrameDelay 5 FrameDelay
Transmit 6 Transmit

6.14.13.30 SLEEPSTATE
Address offset: 0x420
Sleep state during automatic collision resolution

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R SLEEPSTATE Reflects the sleep state during automatic collision resolution. Set to IDLE by
a GOIDLE task. Set to SLEEP_A when a valid SLEEP_REQ frame is received or
by a GOSLEEP task.
Idle 0 State is IDLE.
SleepA 1 State is SLEEP_A.

6.14.13.31 FIELDPRESENT
Address offset: 0x43C
Indicates the presence or not of a valid field

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R FIELDPRESENT Indicates if a valid field is present. Available only in the activated state.
NoField 0 No valid field detected
FieldPresent 1 Valid field detected
B R LOCKDETECT Indicates if the low level has locked to the field
NotLocked 0 Not locked to field
Locked 1 Locked to field

6.14.13.32 FRAMEDELAYMIN
Address offset: 0x504
Minimum frame delay

4413_417 v1.9 393

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000480 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW FRAMEDELAYMIN Minimum frame delay in number of 13.56 MHz clocks

6.14.13.33 FRAMEDELAYMAX
Address offset: 0x508
Maximum frame delay

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A

Reset 0x00001000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW FRAMEDELAYMAX Maximum frame delay in number of 13.56 MHz clocks

6.14.13.34 FRAMEDELAYMODE
Address offset: 0x50C
Configuration register for the Frame Delay Timer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A

Reset 0x00000001 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
ID R/W Field Value ID Value Description
A RW FRAMEDELAYMODE Configuration register for the Frame Delay Timer
FreeRun 0 Transmission is independent of frame timer and will start when the STARTTX
task is triggered. No timeout.
Window 1 Frame is transmitted between FRAMEDELAYMIN and FRAMEDELAYMAX
ExactVal 2 Frame is transmitted exactly at FRAMEDELAYMAX
WindowGrid 3 Frame is transmitted on a bit grid between FRAMEDELAYMIN and
FRAMEDELAYMAX

6.14.13.35 PACKETPTR
Address offset: 0x510
Packet pointer for TXD and RXD data storage in Data RAM

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PTR Packet pointer for TXD and RXD data storage in Data RAM. This address is a
byte-aligned RAM address.

Note: See the memory chapter for details about which memories
are available for EasyDMA.

6.14.13.36 MAXLEN
Address offset: 0x514

4413_417 v1.9 394

 Peripherals

Size of the RAM buffer allocated to TXD and RXD data storage each

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A
Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW MAXLEN [0..257] Size of the RAM buffer allocated to TXD and RXD data storage each

6.14.13.37 TXD.FRAMECONFIG
Address offset: 0x518
Configuration of outgoing frames

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID D C B A

Reset 0x00000017 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 1 1
ID R/W Field Value ID Value Description
A RW PARITY Indicates if parity is added to the frame
NoParity 0 Parity is not added to TX frames
Parity 1 Parity is added to TX frames
B RW DISCARDMODE Discarding unused bits at start or end of a frame
DiscardEnd 0 Unused bits are discarded at end of frame (EoF)
DiscardStart 1 Unused bits are discarded at start of frame (SoF)
C RW SOF Adding SoF or not in TX frames
NoSoF 0 SoF symbol not added
SoF 1 SoF symbol added
D RW CRCMODETX CRC mode for outgoing frames
NoCRCTX 0 CRC is not added to the frame
CRC16TX 1 16 bit CRC added to the frame based on all the data read from RAM that is
used in the frame

6.14.13.38 TXD.AMOUNT
Address offset: 0x51C
Size of outgoing frame

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B B B B B B B B B A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TXDATABITS [0..7] Number of bits in the last or first byte read from RAM that shall be included
in the frame (excluding parity bit).

The DISCARDMODE field in FRAMECONFIG.TX selects if unused bits is

discarded at the start or at the end of a frame. A value of 0 data bytes and 0
data bits is invalid.
B RW TXDATABYTES [0..257] Number of complete bytes that shall be included in the frame, excluding
CRC, parity and framing

6.14.13.39 RXD.FRAMECONFIG
Address offset: 0x520
Configuration of incoming frames

4413_417 v1.9 395

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A

Reset 0x00000015 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 1
ID R/W Field Value ID Value Description
A RW PARITY Indicates if parity expected in RX frame
NoParity 0 Parity is not expected in RX frames
Parity 1 Parity is expected in RX frames
B RW SOF SoF expected or not in RX frames
NoSoF 0 SoF symbol is not expected in RX frames
SoF 1 SoF symbol is expected in RX frames
C RW CRCMODERX CRC mode for incoming frames
NoCRCRX 0 CRC is not expected in RX frames
CRC16RX 1 Last 16 bits in RX frame is CRC, CRC is checked and CRCSTATUS updated

6.14.13.40 RXD.AMOUNT
Address offset: 0x524
Size of last incoming frame

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B B B B B B B B B A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R RXDATABITS Number of bits in the last byte in the frame, if less than 8 (including CRC,
but excluding parity and SoF/EoF framing).

Frames with 0 data bytes and less than 7 data bits are invalid and are not
received properly.
B R RXDATABYTES Number of complete bytes received in the frame (including CRC, but
excluding parity and SoF/EoF framing)

6.14.13.41 NFCID1_LAST
Address offset: 0x590
Last NFCID1 part (4, 7 or 10 bytes ID)

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID D D D D D D D D C C C C C C C C B B B B B B B B A A A A A A A A

Reset 0x00006363 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 0 0 0 1 1 0 1 1 0 0 0 1 1
ID R/W Field Value ID Value Description
A RW NFCID1_Z NFCID1 byte Z (very last byte sent)
B RW NFCID1_Y NFCID1 byte Y
C RW NFCID1_X NFCID1 byte X
D RW NFCID1_W NFCID1 byte W

6.14.13.42 NFCID1_2ND_LAST
Address offset: 0x594
Second last NFCID1 part (7 or 10 bytes ID)

4413_417 v1.9 396

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C C C C C C C C B B B B B B B B A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW NFCID1_V NFCID1 byte V
B RW NFCID1_U NFCID1 byte U
C RW NFCID1_T NFCID1 byte T

6.14.13.43 NFCID1_3RD_LAST
Address offset: 0x598
Third last NFCID1 part (10 bytes ID)

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C C C C C C C C B B B B B B B B A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW NFCID1_S NFCID1 byte S
B RW NFCID1_R NFCID1 byte R
C RW NFCID1_Q NFCID1 byte Q

6.14.13.44 AUTOCOLRESCONFIG
Address offset: 0x59C
Controls the auto collision resolution function. This setting must be done before the NFCT peripheral is
activated.

Note: When modifiying this register bit 1 must be written to '1'.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
A RW MODE Enables/disables auto collision resolution
Enabled 0 Auto collision resolution enabled
Disabled 1 Auto collision resolution disabled

6.14.13.45 SENSRES
Address offset: 0x5A0
NFC-A SENS_RES auto-response settings

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E E E D D D D C C B A A A A A

Reset 0x00000001 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
ID R/W Field Value ID Value Description
A RW BITFRAMESDD Bit frame SDD as defined by the b5:b1 of byte 1 in SENS_RES response in the
NFC Forum, NFC Digital Protocol Technical Specification
SDD00000 0 SDD pattern 00000
SDD00001 1 SDD pattern 00001
SDD00010 2 SDD pattern 00010

4413_417 v1.9 397

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E E E E D D D D C C B A A A A A

Reset 0x00000001 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
ID R/W Field Value ID Value Description
SDD00100 4 SDD pattern 00100
SDD01000 8 SDD pattern 01000
SDD10000 16 SDD pattern 10000
B RW RFU5 Reserved for future use. Shall be 0.
C RW NFCIDSIZE NFCID1 size. This value is used by the auto collision resolution engine.
NFCID1Single 0 NFCID1 size: single (4 bytes)
NFCID1Double 1 NFCID1 size: double (7 bytes)
NFCID1Triple 2 NFCID1 size: triple (10 bytes)
D RW PLATFCONFIG Tag platform configuration as defined by the b4:b1 of byte 2 in SENS_RES
response in the NFC Forum, NFC Digital Protocol Technical Specification
E RW RFU74 Reserved for future use. Shall be 0.

6.14.13.46 SELRES
Address offset: 0x5A4
NFC-A SEL_RES auto-response settings

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E D D C C B A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW RFU10 Reserved for future use. Shall be 0.
B RW CASCADE Cascade as defined by the b3 of SEL_RES response in the NFC Forum, NFC
Digital Protocol Technical Specification (controlled by hardware, shall be 0)
C RW RFU43 Reserved for future use. Shall be 0.
D RW PROTOCOL Protocol as defined by the b7:b6 of SEL_RES response in the NFC Forum,
NFC Digital Protocol Technical Specification
E RW RFU7 Reserved for future use. Shall be 0.

6.14.14 Electrical specification

6.14.14.1 NFCT Electrical Specification

Symbol Description Min. Typ. Max. Units

fc Frequency of operation 13.56 MHz
CMI Carrier modulation index 95 %
DR Data Rate 106 kbps
Vsense 17
Peak differential Field detect threshold level on NFC1-NFC2 1.2 Vp

Imax Maximum input current on NFCT pins 80 mA

17
Input is high impedance in sense mode

4413_417 v1.9 398

 Peripherals

6.14.14.2 NFCT Timing Parameters

Symbol Description Min. Typ. Max. Units

tactivate Time from task_ACTIVATE in SENSE or DISABLE state to ACTIVATE_A or IDLE 500 µs
18
state
tsense Time from remote field is present in SENSE mode to FIELDDETECTED event is 20 µs
asserted

ACTIVATE

DISABLE
TASKS

SENSE
tactivate
tsense tsense
RF-Carrier

MODES DISABLE SENSE_FIELD IDLERU Activated DISABLE

READY
FIELDDETECTED

FIELDLOST

FIELDDETECTED
EVENTS

Figure 69: NFCT timing parameters (Shortcuts for FIELDDETECTED and FIELDLOST are disabled)

6.15 PDM — Pulse density modulation interface

The pulse density modulation (PDM) module enables input of pulse density modulated signals from
external audio frontends, for example, digital microphones. The PDM module generates the PDM clock
and supports single-channel or dual-channel (left and right) data input. Data is transferred directly to RAM
buffers using EasyDMA.
Listed here are the main features for PDM:
• Up to two PDM microphones configured as a left/right pair using the same data input
• 16 kHz output sample rate, 16-bit samples
• EasyDMA support for sample buffering
• HW decimation filters
• Selectable ratio of 64 or 80 between PDM_CLK and output sample rate
The PDM module illustrated below is interfacing up to two digital microphones with the PDM interface.
EasyDMA is implemented to relieve the real-time requirements associated with controlling of the PDM
slave from a low priority CPU execution context. It also includes all the necessary digital filter elements to
produce pulse code modulation (PCM) samples. The PDM module allows continuous audio streaming.

CLK Master clock

generator

Bandpass and
PDM to PCM
decimation (left)
EasyDMA
Sampling

RAM

DIN
Bandpass and
PDM to PCM
decimation (right)

Figure 70: PDM module

18
Does not account for voltage supply and oscillator startup times

4413_417 v1.9 399

 Peripherals

6.15.1 Master clock generator

The master clock generator's PDMCLKCTRL register allows adjusting the PDM clock's frequency.
The master clock generator does not add any jitter to the HFCLK source chosen. It is recommended (but
not mandatory) to use the Xtal as HFCLK source.

6.15.2 Module operation

By default, bits from the left PDM microphone are sampled on PDM_CLK falling edge, and bits for the right
are sampled on the rising edge of PDM_CLK, resulting in two bitstreams. Each bitstream is fed into a digital
filter which converts the PDM stream into 16-bit PCM samples, then filters and down-samples them to
reach the appropriate sample rate.
The EDGE field in the MODE register allows swapping left and right, so that left will be sampled on rising
edge, and right on falling.
The PDM module uses EasyDMA to store the samples coming out from the filters into one buffer in RAM.
Depending on the mode chosen in the OPERATION field in the MODE register, memory either contains
alternating left and right 16-bit samples (Stereo), or only left 16-bit samples (Mono). To ensure continuous
PDM sampling, it is up to the application to update the EasyDMA destination address pointer as the
previous buffer is filled.
The continuous transfer can be started or stopped by sending the START and STOP tasks. STOP becomes
effective after the current frame has finished transferring, which will generate the STOPPED event. The
STOPPED event indicates that all activity in the module is finished, and that the data is available in RAM
(EasyDMA has finished transferring as well). Attempting to restart before receiving the STOPPED event
may result in unpredictable behavior.

6.15.3 Decimation filter

In order to convert the incoming data stream into PCM audio samples, a decimation filter is included in
the PDM interface module.
The input of the filter is the two-channel PDM serial stream (with left channel on clock high, right channel
on clock low). Depending on the RATIO selected, its output is 2 × 16-bit PCM samples at a sample rate
either 64 times or 80 times (depending on the RATIO register) lower than the PDM clock rate.
The filter stage of each channel is followed by a digital volume control, to attenuate or amplify the output
samples in a range of -20 dB to +20 dB around the default (reset) setting, defined by GPDM,default. The gain
is controlled by the GAINL and GAINR registers.
As an example, if the goal is to achieve 2500 RMS output samples (16-bit) with a 1 kHz 90 dBA signal into a
-26 dBFS sensitivity PDM microphone, do the following:
• Sum the PDM module's default gain ( GPDM,default ) and the gain introduced by the microphone and
acoustic path of his implementation (an attenuation would translate into a negative gain)
• Adjust GAINL and GAINR by the above summed amount. Assuming that only the PDM module
influences the gain, GAINL and GAINR must be set to -GPDM,default dB to achieve the requirement.
With GPDM,default=3.2 dB, and as GAINL and GAINR are expressed in 0.5 dB steps, the closest value to
program would be 3.0 dB, which can be calculated as:

GAINL = GAINR = (DefaultGain - (2 * 3))

Remember to check that the resulting values programmed into GAINL and GAINR fall within MinGain and
MaxGain.

6.15.4 EasyDMA
Samples will be written directly to RAM, and EasyDMA must be configured accordingly.

4413_417 v1.9 400

 Peripherals

The address pointer for the EasyDMA channel is set in SAMPLE.PTR register. If the destination address set
in SAMPLE.PTR is not pointing to the Data RAM region, an EasyDMA transfer may result in a HardFault or
RAM corruption. See Memory on page 21 for more information about the different memory regions.
DMA supports Stereo (Left+Right 16-bit samples) and Mono (Left only) data transfer, depending on the
setting in the OPERATION field in the MODE register. The samples are stored little endian.

MODE.OPERATION Bits per sample Result stored per RAM Physical RAM allocated Result boundary indexes Note
word (32-bit words) in RAM
Stereo 32 (2x16) L+R ceil(SAMPLE.MAXCNT/2) R0=[31:16]; L0=[15:0] Default
Mono 16 2xL ceil(SAMPLE.MAXCNT/2) L1=[31:16]; L0=[15:0]

Table 26: DMA sample storage

The destination buffer in RAM consists of one block, the size of which is set in SAMPLE.MAXCNT register.
Format is number of 16-bit samples. The physical RAM allocated is always:

(RAM allocation, in bytes) = SAMPLE.MAXCNT * 2;

(but the mapping of the samples depends on MODE.OPERATION.

If OPERATION=Stereo, RAM will contain a succession of left and right samples.
If OPERATION=Mono, RAM will contain a succession of left only samples.
For a given value of SAMPLE.MAXCNT, the buffer in RAM can contain half the stereo sampling time as
compared to the mono sampling time.
The PDM acquisition can be started by the START task, after the SAMPLE.PTR and SAMPLE.MAXCNT
registers have been written. When starting the module, it will take some time for the filters to start
outputting valid data. Transients from the PDM microphone itself may also occur. The first few samples
(typically around 50) might hence contain invalid values or transients. It is therefore advised to discard the
first few samples after a PDM start.
As soon as the STARTED event is received, the firmware can write the next SAMPLE.PTR value (this register
is double-buffered), to ensure continuous operation.
When the buffer in RAM is filled with samples, an END event is triggered. The firmware can start
processing the data in the buffer. Meanwhile, the PDM module starts acquiring data into the new buffer
pointed to by SAMPLE.PTR, and sends a new STARTED event, so that the firmware can update SAMPLE.PTR
to the next buffer address.

6.15.5 Hardware example

PDM can be configured with a single microphone (mono), or with two microphones.
When a single microphone is used, connect the microphone clock to CLK, and data to DIN.
Vdd nRFxxxxx

CLK CLK

L/R DATA DIN

CLK
DIN

Figure 71: Example of a single PDM microphone, wired as left

4413_417 v1.9 401

 Peripherals

Vdd nRFxxxxx

CLK CLK

L/R DATA DIN

CLK
DIN

Figure 72: Example of a single PDM microphone, wired as right

Note that in a single-microphone (mono) configuration, depending on the microphone’s implementation,

either the left or the right channel (sampled at falling or rising CLK edge respectively) will contain reliable
data.
If two microphones are used, one of them has to be set as left, the other as right (L/R pin tied high or to
GND on the respective microphone). It is strongly recommended to use two microphones of exactly the
same brand and type so that their timings in left and right operation match.
Vdd nRFxxxxx

CLK CLK

L/R DATA DIN

Vdd

CLK

L/R DATA
CLK
DIN

Figure 73: Example of two PDM microphones

6.15.6 Pin configuration

The CLK and DIN signals associated to the PDM module are mapped to physical pins according to the
configuration specified in the PSEL.CLK and PSEL.DIN registers respectively. If the CONNECT field in any
PSEL register is set to Disconnected, the associated PDM module signal will not be connected to the
required physical pins, and will not operate properly.
The PSEL.CLK and PSEL.DIN registers and their configurations are only used as long as the PDM module is
enabled, and retained only as long as the device is in System ON mode. See POWER — Power supply on
page 80 for more information about power modes. When the peripheral is disabled, the pins will behave
as regular GPIOs, and use the configuration in their respective OUT bit field and PIN_CNF[n] register.
To ensure correct behavior in the PDM module, the pins used by the PDM module must be configured
in the GPIO peripheral as described in GPIO configuration before enabling peripheral on page 402
before enabling the PDM module. This is to ensure that the pins used by the PDM module are driven
correctly if the PDM module itself is temporarily disabled or the device temporarily enters System OFF.
This configuration must be retained in the GPIO for the selected I/Os as long as the PDM module is
supposed to be connected to an external PDM circuit.
Only one peripheral can be assigned to drive a particular GPIO pin at a time. Failing to do so may result in
unpredictable behavior.

PDM signal PDM pin Direction Output value Comment

CLK As specified in PSEL.CLK Output 0

DIN As specified in PSEL.DIN Input Not applicable

Table 27: GPIO configuration before enabling peripheral

4413_417 v1.9 402

 Peripherals

6.15.7 Registers
Instances

Instance Base address Description

PDM 0x4001D000 Pulse Density modulation (digital microphone) interface

Register overview

Register Offset Description

TASKS_START 0x000 Starts continuous PDM transfer
TASKS_STOP 0x004 Stops PDM transfer
EVENTS_STARTED 0x100 PDM transfer has started
EVENTS_STOPPED 0x104 PDM transfer has finished
EVENTS_END 0x108 The PDM has written the last sample specified by SAMPLE.MAXCNT (or the last sample after a STOP
task has been received) to Data RAM
INTEN 0x300 Enable or disable interrupt
INTENSET 0x304 Enable interrupt
INTENCLR 0x308 Disable interrupt
ENABLE 0x500 PDM module enable register
PDMCLKCTRL 0x504 PDM clock generator control
MODE 0x508 Defines the routing of the connected PDM microphones' signals
GAINL 0x518 Left output gain adjustment
GAINR 0x51C Right output gain adjustment
RATIO 0x520 Selects the ratio between PDM_CLK and output sample rate. Change PDMCLKCTRL accordingly.
PSEL.CLK 0x540 Pin number configuration for PDM CLK signal
PSEL.DIN 0x544 Pin number configuration for PDM DIN signal
SAMPLE.PTR 0x560 RAM address pointer to write samples to with EasyDMA
SAMPLE.MAXCNT 0x564 Number of samples to allocate memory for in EasyDMA mode

6.15.7.1 TASKS_START
Address offset: 0x000
Starts continuous PDM transfer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_START Starts continuous PDM transfer
Trigger 1 Trigger task

6.15.7.2 TASKS_STOP
Address offset: 0x004
Stops PDM transfer

4413_417 v1.9 403

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STOP Stops PDM transfer
Trigger 1 Trigger task

6.15.7.3 EVENTS_STARTED
Address offset: 0x100
PDM transfer has started

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_STARTED PDM transfer has started
NotGenerated 0 Event not generated
Generated 1 Event generated

6.15.7.4 EVENTS_STOPPED
Address offset: 0x104
PDM transfer has finished

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_STOPPED PDM transfer has finished
NotGenerated 0 Event not generated
Generated 1 Event generated

6.15.7.5 EVENTS_END
Address offset: 0x108
The PDM has written the last sample specified by SAMPLE.MAXCNT (or the last sample after a STOP task
has been received) to Data RAM

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_END The PDM has written the last sample specified by SAMPLE.MAXCNT (or the
last sample after a STOP task has been received) to Data RAM
NotGenerated 0 Event not generated
Generated 1 Event generated

6.15.7.6 INTEN
Address offset: 0x300
Enable or disable interrupt

4413_417 v1.9 404

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW STARTED Enable or disable interrupt for event STARTED
Disabled 0 Disable
Enabled 1 Enable
B RW STOPPED Enable or disable interrupt for event STOPPED
Disabled 0 Disable
Enabled 1 Enable
C RW END Enable or disable interrupt for event END
Disabled 0 Disable
Enabled 1 Enable

6.15.7.7 INTENSET
Address offset: 0x304
Enable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW STARTED Write '1' to enable interrupt for event STARTED
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW STOPPED Write '1' to enable interrupt for event STOPPED
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW END Write '1' to enable interrupt for event END
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.15.7.8 INTENCLR
Address offset: 0x308
Disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW STARTED Write '1' to disable interrupt for event STARTED
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW STOPPED Write '1' to disable interrupt for event STOPPED
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

4413_417 v1.9 405

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
C RW END Write '1' to disable interrupt for event END
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.15.7.9 ENABLE
Address offset: 0x500
PDM module enable register

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW ENABLE Enable or disable PDM module
Disabled 0 Disable
Enabled 1 Enable

6.15.7.10 PDMCLKCTRL
Address offset: 0x504
PDM clock generator control

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x08400000 0 0 0 0 1 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW FREQ PDM_CLK frequency configuration
1000K 0x08000000 PDM_CLK = 32 MHz / 32 = 1.000 MHz
Default 0x08400000 PDM_CLK = 32 MHz / 31 = 1.032 MHz. Nominal clock for RATIO=Ratio64.
1067K 0x08800000 PDM_CLK = 32 MHz / 30 = 1.067 MHz
1231K 0x09800000 PDM_CLK = 32 MHz / 26 = 1.231 MHz
1280K 0x0A000000 PDM_CLK = 32 MHz / 25 = 1.280 MHz. Nominal clock for RATIO=Ratio80.
1333K 0x0A800000 PDM_CLK = 32 MHz / 24 = 1.333 MHz

6.15.7.11 MODE
Address offset: 0x508
Defines the routing of the connected PDM microphones' signals

4413_417 v1.9 406

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW OPERATION Mono or stereo operation
Stereo 0 Sample and store one pair (left + right) of 16-bit samples per RAM word
R=[31:16]; L=[15:0]
Mono 1 Sample and store two successive left samples (16 bits each) per RAM word
L1=[31:16]; L0=[15:0]
B RW EDGE Defines on which PDM_CLK edge left (or mono) is sampled
LeftFalling 0 Left (or mono) is sampled on falling edge of PDM_CLK
LeftRising 1 Left (or mono) is sampled on rising edge of PDM_CLK

6.15.7.12 GAINL
Address offset: 0x518
Left output gain adjustment

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000028 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
ID R/W Field Value ID Value Description
A RW GAINL Left output gain adjustment, in 0.5 dB steps, around the default module gain
(see electrical parameters)

0x00 -20 dB gain adjust

0x01 -19.5 dB gain adjust

(...)

0x27 -0.5 dB gain adjust

0x28 0 dB gain adjust

0x29 +0.5 dB gain adjust

(...)

0x4F +19.5 dB gain adjust

0x50 +20 dB gain adjust

MinGain 0x00 -20 dB gain adjustment (minimum)
DefaultGain 0x28 0 dB gain adjustment
MaxGain 0x50 +20 dB gain adjustment (maximum)

6.15.7.13 GAINR
Address offset: 0x51C
Right output gain adjustment

4413_417 v1.9 407

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000028 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0
ID R/W Field Value ID Value Description
A RW GAINR Right output gain adjustment, in 0.5 dB steps, around the default module
gain (see electrical parameters)
MinGain 0x00 -20 dB gain adjustment (minimum)
DefaultGain 0x28 0 dB gain adjustment
MaxGain 0x50 +20 dB gain adjustment (maximum)

6.15.7.14 RATIO
Address offset: 0x520
Selects the ratio between PDM_CLK and output sample rate. Change PDMCLKCTRL accordingly.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW RATIO Selects the ratio between PDM_CLK and output sample rate
Ratio64 0 Ratio of 64
Ratio80 1 Ratio of 80

6.15.7.15 PSEL.CLK
Address offset: 0x540
Pin number configuration for PDM CLK signal

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.15.7.16 PSEL.DIN
Address offset: 0x544
Pin number configuration for PDM DIN signal

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

4413_417 v1.9 408

 Peripherals

6.15.7.17 SAMPLE.PTR
Address offset: 0x560
RAM address pointer to write samples to with EasyDMA

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW SAMPLEPTR Address to write PDM samples to over DMA

Note: See the memory chapter for details about which memories
are available for EasyDMA.

6.15.7.18 SAMPLE.MAXCNT
Address offset: 0x564
Number of samples to allocate memory for in EasyDMA mode

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW BUFFSIZE [0..32767] Length of DMA RAM allocation in number of samples

6.15.8 Electrical specification

6.15.8.1 PDM Electrical Specification

Symbol Description Min. Typ. Max. Units

fPDM,CLK,64 PDM clock speed. PDMCLKCTRL = Default (Setting needed for 16 MHz sample 1.032 MHz
frequency @ RATIO = Ratio64)
fPDM,CLK,80 PDM clock speed. PDMCLKCTRL = 1280K (Setting needed for 16 MHz sample 1.280 MHz
frequency @ RATIO = Ratio80)
tPDM,JITTER Jitter in PDM clock output 20 ns
TdPDM,CLK PDM clock duty cycle 40 50 60 %
tPDM,DATA Decimation filter delay 5 ms
tPDM,cv Allowed clock edge to data valid 125 ns
tPDM,ci Allowed (other) clock edge to data invalid 0 ns
tPDM,s Data setup time at fPDM,CLK=1.024 MHz or 1.280 MHz 65 ns
tPDM,h Data hold time at fPDM,CLK=1.024 MHz or 1.280 MHz 0 ns
GPDM,default Default (reset) absolute gain of the PDM module 3.2 dB

4413_417 v1.9 409

 Peripherals

tPDM,CLK

CLK

tPDM,cv tPDM,s tPDM,h=tPDM,ci

DIN (L)
tPDM,cv tPDM,s tPDM,h=tPDM,ci

DIN(R)

Figure 74: PDM timing diagram

6.16 PPI — Programmable peripheral interconnect

The programmable peripheral interconnect (PPI) enables peripherals to interact autonomously with each
other using tasks and events independent of the CPU. The PPI allows precise synchronization between
peripherals when real-time application constraints exist and eliminates the need for CPU activity to
implement behavior which can be predefined using PPI.
CH[1].EEP
CH[0].EEP CH[n].EEP
Event 1
Event 2
Peripheral 1

Event 1
Event 2
Peripheral 2 Event 3

0 0 0
1 1 1

n n n

CHEN CHG[0] ... CHG[m]

16MHz

Task 1
Peripheral 1

Task 1
Task 2
Task 3 Peripheral 2

CH[0].TEP FORK[0].TEP
Figure 75: PPI block diagram

The PPI system has, in addition to the fully programmable peripheral interconnections, a set of channels
where the event end point (EEP) and task end points (TEP) are fixed in hardware. These fixed channels can
be individually enabled, disabled, or added to PPI channel groups (see CHG[n] registers), in the same way
as ordinary PPI channels.

4413_417 v1.9 410

 Peripherals

Instance Channel Number of channels

PPI 0-19 20
PPI (fixed) 20-31 12

Table 28: Configurable and fixed PPI channels

The PPI provides a mechanism to automatically trigger a task in one peripheral as a result of an event
occurring in another peripheral. A task is connected to an event through a PPI channel. The PPI channel
is composed of three end point registers, one EEP, and two TEPs. A peripheral task is connected to a TEP
using the address of the task register associated with the task. Similarly, a peripheral event is connected to
an EEP using the address of the event register associated with the event.
On each PPI channel, the signals are synchronized to the 16 MHz clock to avoid any internal violation
of setup and hold timings. As a consequence, events that are synchronous to the 16 MHz clock will be
delayed by one clock period, while other asynchronous events will be delayed by up to one 16 MHz clock
period.

Note: Shortcuts (as defined in the SHORTS register in each peripheral) are not affected by this 16
MHz synchronization, and are therefore not delayed.

Each TEP implements a fork mechanism that enables a second task to be triggered at the same time as the
task specified in the TEP is triggered. This second task is configured in the task end point register in the
FORK registers groups, e.g. FORK.TEP[0] is associated with PPI channel CH[0].
There are two ways of enabling and disabling PPI channels:
• Enable or disable PPI channels individually using the CHEN, CHENSET, and CHENCLR registers.
• Enable or disable PPI channels in PPI channel groups through the groups’ ENABLE and DISABLE tasks.
Prior to these tasks being triggered, the PPI channel group must be configured to define which PPI
channels belong to which groups.

Note: When a channel belongs to two groups m and n, and the tasks CHG[m].EN and CHG[n].DIS
occur simultaneously (m and n can be equal or different), the CHG[m].EN on that channel has
priority.

PPI tasks (for example, CHG[0].EN) can be triggered through the PPI like any other task, which means they
can be hooked to a PPI channel as a TEP. One event can trigger multiple tasks by using multiple channels
and one task can be triggered by multiple events in the same way.

6.16.1 Pre-programmed channels

Some of the PPI channels are pre-programmed. These channels cannot be configured by the CPU, but can
be added to groups and enabled and disabled like the general purpose PPI channels. The FORK TEP for
these channels are still programmable and can be used by the application.
For a list of pre-programmed PPI channels, see the following table.

4413_417 v1.9 411

 Peripherals

Channel EEP TEP

20 TIMER0->EVENTS_COMPARE[0] RADIO->TASKS_TXEN
21 TIMER0->EVENTS_COMPARE[0] RADIO->TASKS_RXEN
22 TIMER0->EVENTS_COMPARE[1] RADIO->TASKS_DISABLE
23 RADIO->EVENTS_BCMATCH AAR->TASKS_START
24 RADIO->EVENTS_READY CCM->TASKS_KSGEN
25 RADIO->EVENTS_ADDRESS CCM->TASKS_CRYPT
26 RADIO->EVENTS_ADDRESS TIMER0->TASKS_CAPTURE[1]
27 RADIO->EVENTS_END TIMER0->TASKS_CAPTURE[2]
28 RTC0->EVENTS_COMPARE[0] RADIO->TASKS_TXEN
29 RTC0->EVENTS_COMPARE[0] RADIO->TASKS_RXEN
30 RTC0->EVENTS_COMPARE[0] TIMER0->TASKS_CLEAR
31 RTC0->EVENTS_COMPARE[0] TIMER0->TASKS_START

Table 29: Pre-programmed channels

6.16.2 Registers
Instances

Instance Base address Description

PPI 0x4001F000 Programmable peripheral interconnect

Configuration

Instance Configuration
PPI This PPI instance has 20 configurable channels (CH[0..19]) and 12 pre-programmed channels (CH[20..31])

Register overview

Register Offset Description

TASKS_CHG[0].EN 0x000 Enable channel group 0
TASKS_CHG[0].DIS 0x004 Disable channel group 0
TASKS_CHG[1].EN 0x008 Enable channel group 1
TASKS_CHG[1].DIS 0x00C Disable channel group 1
TASKS_CHG[2].EN 0x010 Enable channel group 2
TASKS_CHG[2].DIS 0x014 Disable channel group 2
TASKS_CHG[3].EN 0x018 Enable channel group 3
TASKS_CHG[3].DIS 0x01C Disable channel group 3
TASKS_CHG[4].EN 0x020 Enable channel group 4
TASKS_CHG[4].DIS 0x024 Disable channel group 4
TASKS_CHG[5].EN 0x028 Enable channel group 5
TASKS_CHG[5].DIS 0x02C Disable channel group 5
CHEN 0x500 Channel enable register
CHENSET 0x504 Channel enable set register
CHENCLR 0x508 Channel enable clear register
CH[0].EEP 0x510 Channel 0 event endpoint
CH[0].TEP 0x514 Channel 0 task endpoint
CH[1].EEP 0x518 Channel 1 event endpoint
CH[1].TEP 0x51C Channel 1 task endpoint
CH[2].EEP 0x520 Channel 2 event endpoint

4413_417 v1.9 412

 Peripherals

Register Offset Description

CH[2].TEP 0x524 Channel 2 task endpoint
CH[3].EEP 0x528 Channel 3 event endpoint
CH[3].TEP 0x52C Channel 3 task endpoint
CH[4].EEP 0x530 Channel 4 event endpoint
CH[4].TEP 0x534 Channel 4 task endpoint
CH[5].EEP 0x538 Channel 5 event endpoint
CH[5].TEP 0x53C Channel 5 task endpoint
CH[6].EEP 0x540 Channel 6 event endpoint
CH[6].TEP 0x544 Channel 6 task endpoint
CH[7].EEP 0x548 Channel 7 event endpoint
CH[7].TEP 0x54C Channel 7 task endpoint
CH[8].EEP 0x550 Channel 8 event endpoint
CH[8].TEP 0x554 Channel 8 task endpoint
CH[9].EEP 0x558 Channel 9 event endpoint
CH[9].TEP 0x55C Channel 9 task endpoint
CH[10].EEP 0x560 Channel 10 event endpoint
CH[10].TEP 0x564 Channel 10 task endpoint
CH[11].EEP 0x568 Channel 11 event endpoint
CH[11].TEP 0x56C Channel 11 task endpoint
CH[12].EEP 0x570 Channel 12 event endpoint
CH[12].TEP 0x574 Channel 12 task endpoint
CH[13].EEP 0x578 Channel 13 event endpoint
CH[13].TEP 0x57C Channel 13 task endpoint
CH[14].EEP 0x580 Channel 14 event endpoint
CH[14].TEP 0x584 Channel 14 task endpoint
CH[15].EEP 0x588 Channel 15 event endpoint
CH[15].TEP 0x58C Channel 15 task endpoint
CH[16].EEP 0x590 Channel 16 event endpoint
CH[16].TEP 0x594 Channel 16 task endpoint
CH[17].EEP 0x598 Channel 17 event endpoint
CH[17].TEP 0x59C Channel 17 task endpoint
CH[18].EEP 0x5A0 Channel 18 event endpoint
CH[18].TEP 0x5A4 Channel 18 task endpoint
CH[19].EEP 0x5A8 Channel 19 event endpoint
CH[19].TEP 0x5AC Channel 19 task endpoint
CHG[0] 0x800 Channel group 0
CHG[1] 0x804 Channel group 1
CHG[2] 0x808 Channel group 2
CHG[3] 0x80C Channel group 3
CHG[4] 0x810 Channel group 4
CHG[5] 0x814 Channel group 5
FORK[0].TEP 0x910 Channel 0 task endpoint
FORK[1].TEP 0x914 Channel 1 task endpoint
FORK[2].TEP 0x918 Channel 2 task endpoint
FORK[3].TEP 0x91C Channel 3 task endpoint
FORK[4].TEP 0x920 Channel 4 task endpoint
FORK[5].TEP 0x924 Channel 5 task endpoint
FORK[6].TEP 0x928 Channel 6 task endpoint
FORK[7].TEP 0x92C Channel 7 task endpoint
FORK[8].TEP 0x930 Channel 8 task endpoint
FORK[9].TEP 0x934 Channel 9 task endpoint
FORK[10].TEP 0x938 Channel 10 task endpoint
FORK[11].TEP 0x93C Channel 11 task endpoint

4413_417 v1.9 413

 Peripherals

Register Offset Description

FORK[12].TEP 0x940 Channel 12 task endpoint
FORK[13].TEP 0x944 Channel 13 task endpoint
FORK[14].TEP 0x948 Channel 14 task endpoint
FORK[15].TEP 0x94C Channel 15 task endpoint
FORK[16].TEP 0x950 Channel 16 task endpoint
FORK[17].TEP 0x954 Channel 17 task endpoint
FORK[18].TEP 0x958 Channel 18 task endpoint
FORK[19].TEP 0x95C Channel 19 task endpoint
FORK[20].TEP 0x960 Channel 20 task endpoint
FORK[21].TEP 0x964 Channel 21 task endpoint
FORK[22].TEP 0x968 Channel 22 task endpoint
FORK[23].TEP 0x96C Channel 23 task endpoint
FORK[24].TEP 0x970 Channel 24 task endpoint
FORK[25].TEP 0x974 Channel 25 task endpoint
FORK[26].TEP 0x978 Channel 26 task endpoint
FORK[27].TEP 0x97C Channel 27 task endpoint
FORK[28].TEP 0x980 Channel 28 task endpoint
FORK[29].TEP 0x984 Channel 29 task endpoint
FORK[30].TEP 0x988 Channel 30 task endpoint
FORK[31].TEP 0x98C Channel 31 task endpoint

6.16.2.1 TASKS_CHG[0]
Channel group tasks

6.16.2.1.1 TASKS_CHG[0].EN
Address offset: 0x000
Enable channel group 0

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W EN Enable channel group 0
Trigger 1 Trigger task

6.16.2.1.2 TASKS_CHG[0].DIS
Address offset: 0x004
Disable channel group 0

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W DIS Disable channel group 0
Trigger 1 Trigger task

6.16.2.2 TASKS_CHG[1]
Channel group tasks

4413_417 v1.9 414

 Peripherals

6.16.2.2.1 TASKS_CHG[1].EN
Address offset: 0x008
Enable channel group 1

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W EN Enable channel group 1
Trigger 1 Trigger task

6.16.2.2.2 TASKS_CHG[1].DIS
Address offset: 0x00C
Disable channel group 1

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W DIS Disable channel group 1
Trigger 1 Trigger task

6.16.2.3 TASKS_CHG[2]
Channel group tasks

6.16.2.3.1 TASKS_CHG[2].EN
Address offset: 0x010
Enable channel group 2

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W EN Enable channel group 2
Trigger 1 Trigger task

6.16.2.3.2 TASKS_CHG[2].DIS
Address offset: 0x014
Disable channel group 2

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W DIS Disable channel group 2
Trigger 1 Trigger task

4413_417 v1.9 415

 Peripherals

6.16.2.4 TASKS_CHG[3]
Channel group tasks

6.16.2.4.1 TASKS_CHG[3].EN
Address offset: 0x018
Enable channel group 3

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W EN Enable channel group 3
Trigger 1 Trigger task

6.16.2.4.2 TASKS_CHG[3].DIS
Address offset: 0x01C
Disable channel group 3

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W DIS Disable channel group 3
Trigger 1 Trigger task

6.16.2.5 TASKS_CHG[4]
Channel group tasks

6.16.2.5.1 TASKS_CHG[4].EN
Address offset: 0x020
Enable channel group 4

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W EN Enable channel group 4
Trigger 1 Trigger task

6.16.2.5.2 TASKS_CHG[4].DIS
Address offset: 0x024
Disable channel group 4

4413_417 v1.9 416

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W DIS Disable channel group 4
Trigger 1 Trigger task

6.16.2.6 TASKS_CHG[5]
Channel group tasks

6.16.2.6.1 TASKS_CHG[5].EN
Address offset: 0x028
Enable channel group 5

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W EN Enable channel group 5
Trigger 1 Trigger task

6.16.2.6.2 TASKS_CHG[5].DIS
Address offset: 0x02C
Disable channel group 5

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W DIS Disable channel group 5
Trigger 1 Trigger task

6.16.2.7 CHEN
Address offset: 0x500
Channel enable register

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW CH0 Enable or disable channel 0
Disabled 0 Disable channel
Enabled 1 Enable channel
B RW CH1 Enable or disable channel 1
Disabled 0 Disable channel
Enabled 1 Enable channel
C RW CH2 Enable or disable channel 2
Disabled 0 Disable channel

4413_417 v1.9 417

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Enabled 1 Enable channel
D RW CH3 Enable or disable channel 3
Disabled 0 Disable channel
Enabled 1 Enable channel
E RW CH4 Enable or disable channel 4
Disabled 0 Disable channel
Enabled 1 Enable channel
F RW CH5 Enable or disable channel 5
Disabled 0 Disable channel
Enabled 1 Enable channel
G RW CH6 Enable or disable channel 6
Disabled 0 Disable channel
Enabled 1 Enable channel
H RW CH7 Enable or disable channel 7
Disabled 0 Disable channel
Enabled 1 Enable channel
I RW CH8 Enable or disable channel 8
Disabled 0 Disable channel
Enabled 1 Enable channel
J RW CH9 Enable or disable channel 9
Disabled 0 Disable channel
Enabled 1 Enable channel
K RW CH10 Enable or disable channel 10
Disabled 0 Disable channel
Enabled 1 Enable channel
L RW CH11 Enable or disable channel 11
Disabled 0 Disable channel
Enabled 1 Enable channel
M RW CH12 Enable or disable channel 12
Disabled 0 Disable channel
Enabled 1 Enable channel
N RW CH13 Enable or disable channel 13
Disabled 0 Disable channel
Enabled 1 Enable channel
O RW CH14 Enable or disable channel 14
Disabled 0 Disable channel
Enabled 1 Enable channel
P RW CH15 Enable or disable channel 15
Disabled 0 Disable channel
Enabled 1 Enable channel
Q RW CH16 Enable or disable channel 16
Disabled 0 Disable channel
Enabled 1 Enable channel
R RW CH17 Enable or disable channel 17
Disabled 0 Disable channel
Enabled 1 Enable channel
S RW CH18 Enable or disable channel 18
Disabled 0 Disable channel
Enabled 1 Enable channel
T RW CH19 Enable or disable channel 19

4413_417 v1.9 418

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Disabled 0 Disable channel
Enabled 1 Enable channel
U RW CH20 Enable or disable channel 20
Disabled 0 Disable channel
Enabled 1 Enable channel
V RW CH21 Enable or disable channel 21
Disabled 0 Disable channel
Enabled 1 Enable channel
W RW CH22 Enable or disable channel 22
Disabled 0 Disable channel
Enabled 1 Enable channel
X RW CH23 Enable or disable channel 23
Disabled 0 Disable channel
Enabled 1 Enable channel
Y RW CH24 Enable or disable channel 24
Disabled 0 Disable channel
Enabled 1 Enable channel
Z RW CH25 Enable or disable channel 25
Disabled 0 Disable channel
Enabled 1 Enable channel
a RW CH26 Enable or disable channel 26
Disabled 0 Disable channel
Enabled 1 Enable channel
b RW CH27 Enable or disable channel 27
Disabled 0 Disable channel
Enabled 1 Enable channel
c RW CH28 Enable or disable channel 28
Disabled 0 Disable channel
Enabled 1 Enable channel
d RW CH29 Enable or disable channel 29
Disabled 0 Disable channel
Enabled 1 Enable channel
e RW CH30 Enable or disable channel 30
Disabled 0 Disable channel
Enabled 1 Enable channel
f RW CH31 Enable or disable channel 31
Disabled 0 Disable channel
Enabled 1 Enable channel

6.16.2.8 CHENSET
Address offset: 0x504
Channel enable set register

Note: Read: reads value of CHi field in CHEN register.

4413_417 v1.9 419

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW CH0 Channel 0 enable set register. Writing '0' has no effect.
W1S
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Set 1 Write: Enable channel
B RW CH1 Channel 1 enable set register. Writing '0' has no effect.
W1S
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Set 1 Write: Enable channel
C RW CH2 Channel 2 enable set register. Writing '0' has no effect.
W1S
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Set 1 Write: Enable channel
D RW CH3 Channel 3 enable set register. Writing '0' has no effect.
W1S
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Set 1 Write: Enable channel
E RW CH4 Channel 4 enable set register. Writing '0' has no effect.
W1S
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Set 1 Write: Enable channel
F RW CH5 Channel 5 enable set register. Writing '0' has no effect.
W1S
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Set 1 Write: Enable channel
G RW CH6 Channel 6 enable set register. Writing '0' has no effect.
W1S
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Set 1 Write: Enable channel
H RW CH7 Channel 7 enable set register. Writing '0' has no effect.
W1S
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Set 1 Write: Enable channel
I RW CH8 Channel 8 enable set register. Writing '0' has no effect.
W1S
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Set 1 Write: Enable channel
J RW CH9 Channel 9 enable set register. Writing '0' has no effect.
W1S
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Set 1 Write: Enable channel

4413_417 v1.9 420

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
K RW CH10 Channel 10 enable set register. Writing '0' has no effect.
W1S
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Set 1 Write: Enable channel
L RW CH11 Channel 11 enable set register. Writing '0' has no effect.
W1S
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Set 1 Write: Enable channel
M RW CH12 Channel 12 enable set register. Writing '0' has no effect.
W1S
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Set 1 Write: Enable channel
N RW CH13 Channel 13 enable set register. Writing '0' has no effect.
W1S
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Set 1 Write: Enable channel
O RW CH14 Channel 14 enable set register. Writing '0' has no effect.
W1S
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Set 1 Write: Enable channel
P RW CH15 Channel 15 enable set register. Writing '0' has no effect.
W1S
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Set 1 Write: Enable channel
Q RW CH16 Channel 16 enable set register. Writing '0' has no effect.
W1S
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Set 1 Write: Enable channel
R RW CH17 Channel 17 enable set register. Writing '0' has no effect.
W1S
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Set 1 Write: Enable channel
S RW CH18 Channel 18 enable set register. Writing '0' has no effect.
W1S
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Set 1 Write: Enable channel
T RW CH19 Channel 19 enable set register. Writing '0' has no effect.
W1S
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Set 1 Write: Enable channel

4413_417 v1.9 421

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
U RW CH20 Channel 20 enable set register. Writing '0' has no effect.
W1S
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Set 1 Write: Enable channel
V RW CH21 Channel 21 enable set register. Writing '0' has no effect.
W1S
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Set 1 Write: Enable channel
W RW CH22 Channel 22 enable set register. Writing '0' has no effect.
W1S
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Set 1 Write: Enable channel
X RW CH23 Channel 23 enable set register. Writing '0' has no effect.
W1S
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Set 1 Write: Enable channel
Y RW CH24 Channel 24 enable set register. Writing '0' has no effect.
W1S
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Set 1 Write: Enable channel
Z RW CH25 Channel 25 enable set register. Writing '0' has no effect.
W1S
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Set 1 Write: Enable channel
a RW CH26 Channel 26 enable set register. Writing '0' has no effect.
W1S
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Set 1 Write: Enable channel
b RW CH27 Channel 27 enable set register. Writing '0' has no effect.
W1S
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Set 1 Write: Enable channel
c RW CH28 Channel 28 enable set register. Writing '0' has no effect.
W1S
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Set 1 Write: Enable channel
d RW CH29 Channel 29 enable set register. Writing '0' has no effect.
W1S
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Set 1 Write: Enable channel

4413_417 v1.9 422

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
e RW CH30 Channel 30 enable set register. Writing '0' has no effect.
W1S
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Set 1 Write: Enable channel
f RW CH31 Channel 31 enable set register. Writing '0' has no effect.
W1S
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Set 1 Write: Enable channel

6.16.2.9 CHENCLR
Address offset: 0x508
Channel enable clear register

Note: Read: reads value of CHi field in CHEN register.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW CH0 Channel 0 enable clear register. Writing '0' has no effect.
W1C
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Clear 1 Write: disable channel
B RW CH1 Channel 1 enable clear register. Writing '0' has no effect.
W1C
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Clear 1 Write: disable channel
C RW CH2 Channel 2 enable clear register. Writing '0' has no effect.
W1C
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Clear 1 Write: disable channel
D RW CH3 Channel 3 enable clear register. Writing '0' has no effect.
W1C
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Clear 1 Write: disable channel
E RW CH4 Channel 4 enable clear register. Writing '0' has no effect.
W1C
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Clear 1 Write: disable channel
F RW CH5 Channel 5 enable clear register. Writing '0' has no effect.
W1C

4413_417 v1.9 423

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Clear 1 Write: disable channel
G RW CH6 Channel 6 enable clear register. Writing '0' has no effect.
W1C
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Clear 1 Write: disable channel
H RW CH7 Channel 7 enable clear register. Writing '0' has no effect.
W1C
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Clear 1 Write: disable channel
I RW CH8 Channel 8 enable clear register. Writing '0' has no effect.
W1C
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Clear 1 Write: disable channel
J RW CH9 Channel 9 enable clear register. Writing '0' has no effect.
W1C
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Clear 1 Write: disable channel
K RW CH10 Channel 10 enable clear register. Writing '0' has no effect.
W1C
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Clear 1 Write: disable channel
L RW CH11 Channel 11 enable clear register. Writing '0' has no effect.
W1C
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Clear 1 Write: disable channel
M RW CH12 Channel 12 enable clear register. Writing '0' has no effect.
W1C
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Clear 1 Write: disable channel
N RW CH13 Channel 13 enable clear register. Writing '0' has no effect.
W1C
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Clear 1 Write: disable channel
O RW CH14 Channel 14 enable clear register. Writing '0' has no effect.
W1C
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Clear 1 Write: disable channel
P RW CH15 Channel 15 enable clear register. Writing '0' has no effect.
W1C

4413_417 v1.9 424

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Clear 1 Write: disable channel
Q RW CH16 Channel 16 enable clear register. Writing '0' has no effect.
W1C
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Clear 1 Write: disable channel
R RW CH17 Channel 17 enable clear register. Writing '0' has no effect.
W1C
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Clear 1 Write: disable channel
S RW CH18 Channel 18 enable clear register. Writing '0' has no effect.
W1C
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Clear 1 Write: disable channel
T RW CH19 Channel 19 enable clear register. Writing '0' has no effect.
W1C
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Clear 1 Write: disable channel
U RW CH20 Channel 20 enable clear register. Writing '0' has no effect.
W1C
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Clear 1 Write: disable channel
V RW CH21 Channel 21 enable clear register. Writing '0' has no effect.
W1C
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Clear 1 Write: disable channel
W RW CH22 Channel 22 enable clear register. Writing '0' has no effect.
W1C
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Clear 1 Write: disable channel
X RW CH23 Channel 23 enable clear register. Writing '0' has no effect.
W1C
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Clear 1 Write: disable channel
Y RW CH24 Channel 24 enable clear register. Writing '0' has no effect.
W1C
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Clear 1 Write: disable channel
Z RW CH25 Channel 25 enable clear register. Writing '0' has no effect.
W1C

4413_417 v1.9 425

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Clear 1 Write: disable channel
a RW CH26 Channel 26 enable clear register. Writing '0' has no effect.
W1C
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Clear 1 Write: disable channel
b RW CH27 Channel 27 enable clear register. Writing '0' has no effect.
W1C
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Clear 1 Write: disable channel
c RW CH28 Channel 28 enable clear register. Writing '0' has no effect.
W1C
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Clear 1 Write: disable channel
d RW CH29 Channel 29 enable clear register. Writing '0' has no effect.
W1C
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Clear 1 Write: disable channel
e RW CH30 Channel 30 enable clear register. Writing '0' has no effect.
W1C
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Clear 1 Write: disable channel
f RW CH31 Channel 31 enable clear register. Writing '0' has no effect.
W1C
Disabled 0 Read: channel disabled
Enabled 1 Read: channel enabled
Clear 1 Write: disable channel

6.16.2.10 CH[0]
PPI Channel

6.16.2.10.1 CH[0].EEP
Address offset: 0x510
Channel 0 event endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EEP Pointer to event register. Accepts only addresses to registers from the Event
group.

4413_417 v1.9 426

 Peripherals

6.16.2.10.2 CH[0].TEP
Address offset: 0x514
Channel 0 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register. Accepts only addresses to registers from the Task
group.

6.16.2.11 CH[1]
PPI Channel

6.16.2.11.1 CH[1].EEP
Address offset: 0x518
Channel 1 event endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EEP Pointer to event register. Accepts only addresses to registers from the Event
group.

6.16.2.11.2 CH[1].TEP
Address offset: 0x51C
Channel 1 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register. Accepts only addresses to registers from the Task
group.

6.16.2.12 CH[2]
PPI Channel

6.16.2.12.1 CH[2].EEP
Address offset: 0x520
Channel 2 event endpoint

4413_417 v1.9 427

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EEP Pointer to event register. Accepts only addresses to registers from the Event
group.

6.16.2.12.2 CH[2].TEP
Address offset: 0x524
Channel 2 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register. Accepts only addresses to registers from the Task
group.

6.16.2.13 CH[3]
PPI Channel

6.16.2.13.1 CH[3].EEP
Address offset: 0x528
Channel 3 event endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EEP Pointer to event register. Accepts only addresses to registers from the Event
group.

6.16.2.13.2 CH[3].TEP
Address offset: 0x52C
Channel 3 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register. Accepts only addresses to registers from the Task
group.

6.16.2.14 CH[4]
PPI Channel

6.16.2.14.1 CH[4].EEP
Address offset: 0x530

4413_417 v1.9 428

 Peripherals

Channel 4 event endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A
Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EEP Pointer to event register. Accepts only addresses to registers from the Event
group.

6.16.2.14.2 CH[4].TEP
Address offset: 0x534
Channel 4 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register. Accepts only addresses to registers from the Task
group.

6.16.2.15 CH[5]
PPI Channel

6.16.2.15.1 CH[5].EEP
Address offset: 0x538
Channel 5 event endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EEP Pointer to event register. Accepts only addresses to registers from the Event
group.

6.16.2.15.2 CH[5].TEP
Address offset: 0x53C
Channel 5 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register. Accepts only addresses to registers from the Task
group.

6.16.2.16 CH[6]
PPI Channel

4413_417 v1.9 429

 Peripherals

6.16.2.16.1 CH[6].EEP
Address offset: 0x540
Channel 6 event endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EEP Pointer to event register. Accepts only addresses to registers from the Event
group.

6.16.2.16.2 CH[6].TEP
Address offset: 0x544
Channel 6 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register. Accepts only addresses to registers from the Task
group.

6.16.2.17 CH[7]
PPI Channel

6.16.2.17.1 CH[7].EEP
Address offset: 0x548
Channel 7 event endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EEP Pointer to event register. Accepts only addresses to registers from the Event
group.

6.16.2.17.2 CH[7].TEP
Address offset: 0x54C
Channel 7 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register. Accepts only addresses to registers from the Task
group.

4413_417 v1.9 430

 Peripherals

6.16.2.18 CH[8]
PPI Channel

6.16.2.18.1 CH[8].EEP
Address offset: 0x550
Channel 8 event endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EEP Pointer to event register. Accepts only addresses to registers from the Event
group.

6.16.2.18.2 CH[8].TEP
Address offset: 0x554
Channel 8 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register. Accepts only addresses to registers from the Task
group.

6.16.2.19 CH[9]
PPI Channel

6.16.2.19.1 CH[9].EEP
Address offset: 0x558
Channel 9 event endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EEP Pointer to event register. Accepts only addresses to registers from the Event
group.

6.16.2.19.2 CH[9].TEP
Address offset: 0x55C
Channel 9 task endpoint

4413_417 v1.9 431

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register. Accepts only addresses to registers from the Task
group.

6.16.2.20 CH[10]
PPI Channel

6.16.2.20.1 CH[10].EEP
Address offset: 0x560
Channel 10 event endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EEP Pointer to event register. Accepts only addresses to registers from the Event
group.

6.16.2.20.2 CH[10].TEP
Address offset: 0x564
Channel 10 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register. Accepts only addresses to registers from the Task
group.

6.16.2.21 CH[11]
PPI Channel

6.16.2.21.1 CH[11].EEP
Address offset: 0x568
Channel 11 event endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EEP Pointer to event register. Accepts only addresses to registers from the Event
group.

6.16.2.21.2 CH[11].TEP
Address offset: 0x56C

4413_417 v1.9 432

 Peripherals

Channel 11 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A
Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register. Accepts only addresses to registers from the Task
group.

6.16.2.22 CH[12]
PPI Channel

6.16.2.22.1 CH[12].EEP
Address offset: 0x570
Channel 12 event endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EEP Pointer to event register. Accepts only addresses to registers from the Event
group.

6.16.2.22.2 CH[12].TEP
Address offset: 0x574
Channel 12 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register. Accepts only addresses to registers from the Task
group.

6.16.2.23 CH[13]
PPI Channel

6.16.2.23.1 CH[13].EEP
Address offset: 0x578
Channel 13 event endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EEP Pointer to event register. Accepts only addresses to registers from the Event
group.

4413_417 v1.9 433

 Peripherals

6.16.2.23.2 CH[13].TEP
Address offset: 0x57C
Channel 13 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register. Accepts only addresses to registers from the Task
group.

6.16.2.24 CH[14]
PPI Channel

6.16.2.24.1 CH[14].EEP
Address offset: 0x580
Channel 14 event endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EEP Pointer to event register. Accepts only addresses to registers from the Event
group.

6.16.2.24.2 CH[14].TEP
Address offset: 0x584
Channel 14 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register. Accepts only addresses to registers from the Task
group.

6.16.2.25 CH[15]
PPI Channel

6.16.2.25.1 CH[15].EEP
Address offset: 0x588
Channel 15 event endpoint

4413_417 v1.9 434

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EEP Pointer to event register. Accepts only addresses to registers from the Event
group.

6.16.2.25.2 CH[15].TEP
Address offset: 0x58C
Channel 15 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register. Accepts only addresses to registers from the Task
group.

6.16.2.26 CH[16]
PPI Channel

6.16.2.26.1 CH[16].EEP
Address offset: 0x590
Channel 16 event endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EEP Pointer to event register. Accepts only addresses to registers from the Event
group.

6.16.2.26.2 CH[16].TEP
Address offset: 0x594
Channel 16 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register. Accepts only addresses to registers from the Task
group.

6.16.2.27 CH[17]
PPI Channel

6.16.2.27.1 CH[17].EEP
Address offset: 0x598

4413_417 v1.9 435

 Peripherals

Channel 17 event endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A
Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EEP Pointer to event register. Accepts only addresses to registers from the Event
group.

6.16.2.27.2 CH[17].TEP
Address offset: 0x59C
Channel 17 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register. Accepts only addresses to registers from the Task
group.

6.16.2.28 CH[18]
PPI Channel

6.16.2.28.1 CH[18].EEP
Address offset: 0x5A0
Channel 18 event endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EEP Pointer to event register. Accepts only addresses to registers from the Event
group.

6.16.2.28.2 CH[18].TEP
Address offset: 0x5A4
Channel 18 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register. Accepts only addresses to registers from the Task
group.

6.16.2.29 CH[19]
PPI Channel

4413_417 v1.9 436

 Peripherals

6.16.2.29.1 CH[19].EEP
Address offset: 0x5A8
Channel 19 event endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EEP Pointer to event register. Accepts only addresses to registers from the Event
group.

6.16.2.29.2 CH[19].TEP
Address offset: 0x5AC
Channel 19 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register. Accepts only addresses to registers from the Task
group.

6.16.2.30 CHG[0]
Address offset: 0x800
Channel group 0

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A
Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW CH0 Include or exclude channel 0
Excluded 0 Exclude
Included 1 Include
B RW CH1 Include or exclude channel 1
Excluded 0 Exclude
Included 1 Include
C RW CH2 Include or exclude channel 2
Excluded 0 Exclude
Included 1 Include
D RW CH3 Include or exclude channel 3
Excluded 0 Exclude
Included 1 Include
E RW CH4 Include or exclude channel 4
Excluded 0 Exclude
Included 1 Include
F RW CH5 Include or exclude channel 5
Excluded 0 Exclude
Included 1 Include
G RW CH6 Include or exclude channel 6

4413_417 v1.9 437

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Excluded 0 Exclude
Included 1 Include
H RW CH7 Include or exclude channel 7
Excluded 0 Exclude
Included 1 Include
I RW CH8 Include or exclude channel 8
Excluded 0 Exclude
Included 1 Include
J RW CH9 Include or exclude channel 9
Excluded 0 Exclude
Included 1 Include
K RW CH10 Include or exclude channel 10
Excluded 0 Exclude
Included 1 Include
L RW CH11 Include or exclude channel 11
Excluded 0 Exclude
Included 1 Include
M RW CH12 Include or exclude channel 12
Excluded 0 Exclude
Included 1 Include
N RW CH13 Include or exclude channel 13
Excluded 0 Exclude
Included 1 Include
O RW CH14 Include or exclude channel 14
Excluded 0 Exclude
Included 1 Include
P RW CH15 Include or exclude channel 15
Excluded 0 Exclude
Included 1 Include
Q RW CH16 Include or exclude channel 16
Excluded 0 Exclude
Included 1 Include
R RW CH17 Include or exclude channel 17
Excluded 0 Exclude
Included 1 Include
S RW CH18 Include or exclude channel 18
Excluded 0 Exclude
Included 1 Include
T RW CH19 Include or exclude channel 19
Excluded 0 Exclude
Included 1 Include
U RW CH20 Include or exclude channel 20
Excluded 0 Exclude
Included 1 Include
V RW CH21 Include or exclude channel 21
Excluded 0 Exclude
Included 1 Include
W RW CH22 Include or exclude channel 22
Excluded 0 Exclude
Included 1 Include

4413_417 v1.9 438

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
X RW CH23 Include or exclude channel 23
Excluded 0 Exclude
Included 1 Include
Y RW CH24 Include or exclude channel 24
Excluded 0 Exclude
Included 1 Include
Z RW CH25 Include or exclude channel 25
Excluded 0 Exclude
Included 1 Include
a RW CH26 Include or exclude channel 26
Excluded 0 Exclude
Included 1 Include
b RW CH27 Include or exclude channel 27
Excluded 0 Exclude
Included 1 Include
c RW CH28 Include or exclude channel 28
Excluded 0 Exclude
Included 1 Include
d RW CH29 Include or exclude channel 29
Excluded 0 Exclude
Included 1 Include
e RW CH30 Include or exclude channel 30
Excluded 0 Exclude
Included 1 Include
f RW CH31 Include or exclude channel 31
Excluded 0 Exclude
Included 1 Include

6.16.2.31 CHG[1]
Address offset: 0x804
Channel group 1

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW CH0 Include or exclude channel 0
Excluded 0 Exclude
Included 1 Include
B RW CH1 Include or exclude channel 1
Excluded 0 Exclude
Included 1 Include
C RW CH2 Include or exclude channel 2
Excluded 0 Exclude
Included 1 Include
D RW CH3 Include or exclude channel 3
Excluded 0 Exclude
Included 1 Include

4413_417 v1.9 439

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
E RW CH4 Include or exclude channel 4
Excluded 0 Exclude
Included 1 Include
F RW CH5 Include or exclude channel 5
Excluded 0 Exclude
Included 1 Include
G RW CH6 Include or exclude channel 6
Excluded 0 Exclude
Included 1 Include
H RW CH7 Include or exclude channel 7
Excluded 0 Exclude
Included 1 Include
I RW CH8 Include or exclude channel 8
Excluded 0 Exclude
Included 1 Include
J RW CH9 Include or exclude channel 9
Excluded 0 Exclude
Included 1 Include
K RW CH10 Include or exclude channel 10
Excluded 0 Exclude
Included 1 Include
L RW CH11 Include or exclude channel 11
Excluded 0 Exclude
Included 1 Include
M RW CH12 Include or exclude channel 12
Excluded 0 Exclude
Included 1 Include
N RW CH13 Include or exclude channel 13
Excluded 0 Exclude
Included 1 Include
O RW CH14 Include or exclude channel 14
Excluded 0 Exclude
Included 1 Include
P RW CH15 Include or exclude channel 15
Excluded 0 Exclude
Included 1 Include
Q RW CH16 Include or exclude channel 16
Excluded 0 Exclude
Included 1 Include
R RW CH17 Include or exclude channel 17
Excluded 0 Exclude
Included 1 Include
S RW CH18 Include or exclude channel 18
Excluded 0 Exclude
Included 1 Include
T RW CH19 Include or exclude channel 19
Excluded 0 Exclude
Included 1 Include
U RW CH20 Include or exclude channel 20
Excluded 0 Exclude

4413_417 v1.9 440

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Included 1 Include
V RW CH21 Include or exclude channel 21
Excluded 0 Exclude
Included 1 Include
W RW CH22 Include or exclude channel 22
Excluded 0 Exclude
Included 1 Include
X RW CH23 Include or exclude channel 23
Excluded 0 Exclude
Included 1 Include
Y RW CH24 Include or exclude channel 24
Excluded 0 Exclude
Included 1 Include
Z RW CH25 Include or exclude channel 25
Excluded 0 Exclude
Included 1 Include
a RW CH26 Include or exclude channel 26
Excluded 0 Exclude
Included 1 Include
b RW CH27 Include or exclude channel 27
Excluded 0 Exclude
Included 1 Include
c RW CH28 Include or exclude channel 28
Excluded 0 Exclude
Included 1 Include
d RW CH29 Include or exclude channel 29
Excluded 0 Exclude
Included 1 Include
e RW CH30 Include or exclude channel 30
Excluded 0 Exclude
Included 1 Include
f RW CH31 Include or exclude channel 31
Excluded 0 Exclude
Included 1 Include

6.16.2.32 CHG[2]
Address offset: 0x808
Channel group 2

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW CH0 Include or exclude channel 0
Excluded 0 Exclude
Included 1 Include
B RW CH1 Include or exclude channel 1
Excluded 0 Exclude

4413_417 v1.9 441

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Included 1 Include
C RW CH2 Include or exclude channel 2
Excluded 0 Exclude
Included 1 Include
D RW CH3 Include or exclude channel 3
Excluded 0 Exclude
Included 1 Include
E RW CH4 Include or exclude channel 4
Excluded 0 Exclude
Included 1 Include
F RW CH5 Include or exclude channel 5
Excluded 0 Exclude
Included 1 Include
G RW CH6 Include or exclude channel 6
Excluded 0 Exclude
Included 1 Include
H RW CH7 Include or exclude channel 7
Excluded 0 Exclude
Included 1 Include
I RW CH8 Include or exclude channel 8
Excluded 0 Exclude
Included 1 Include
J RW CH9 Include or exclude channel 9
Excluded 0 Exclude
Included 1 Include
K RW CH10 Include or exclude channel 10
Excluded 0 Exclude
Included 1 Include
L RW CH11 Include or exclude channel 11
Excluded 0 Exclude
Included 1 Include
M RW CH12 Include or exclude channel 12
Excluded 0 Exclude
Included 1 Include
N RW CH13 Include or exclude channel 13
Excluded 0 Exclude
Included 1 Include
O RW CH14 Include or exclude channel 14
Excluded 0 Exclude
Included 1 Include
P RW CH15 Include or exclude channel 15
Excluded 0 Exclude
Included 1 Include
Q RW CH16 Include or exclude channel 16
Excluded 0 Exclude
Included 1 Include
R RW CH17 Include or exclude channel 17
Excluded 0 Exclude
Included 1 Include
S RW CH18 Include or exclude channel 18

4413_417 v1.9 442

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Excluded 0 Exclude
Included 1 Include
T RW CH19 Include or exclude channel 19
Excluded 0 Exclude
Included 1 Include
U RW CH20 Include or exclude channel 20
Excluded 0 Exclude
Included 1 Include
V RW CH21 Include or exclude channel 21
Excluded 0 Exclude
Included 1 Include
W RW CH22 Include or exclude channel 22
Excluded 0 Exclude
Included 1 Include
X RW CH23 Include or exclude channel 23
Excluded 0 Exclude
Included 1 Include
Y RW CH24 Include or exclude channel 24
Excluded 0 Exclude
Included 1 Include
Z RW CH25 Include or exclude channel 25
Excluded 0 Exclude
Included 1 Include
a RW CH26 Include or exclude channel 26
Excluded 0 Exclude
Included 1 Include
b RW CH27 Include or exclude channel 27
Excluded 0 Exclude
Included 1 Include
c RW CH28 Include or exclude channel 28
Excluded 0 Exclude
Included 1 Include
d RW CH29 Include or exclude channel 29
Excluded 0 Exclude
Included 1 Include
e RW CH30 Include or exclude channel 30
Excluded 0 Exclude
Included 1 Include
f RW CH31 Include or exclude channel 31
Excluded 0 Exclude
Included 1 Include

6.16.2.33 CHG[3]
Address offset: 0x80C
Channel group 3

4413_417 v1.9 443

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW CH0 Include or exclude channel 0
Excluded 0 Exclude
Included 1 Include
B RW CH1 Include or exclude channel 1
Excluded 0 Exclude
Included 1 Include
C RW CH2 Include or exclude channel 2
Excluded 0 Exclude
Included 1 Include
D RW CH3 Include or exclude channel 3
Excluded 0 Exclude
Included 1 Include
E RW CH4 Include or exclude channel 4
Excluded 0 Exclude
Included 1 Include
F RW CH5 Include or exclude channel 5
Excluded 0 Exclude
Included 1 Include
G RW CH6 Include or exclude channel 6
Excluded 0 Exclude
Included 1 Include
H RW CH7 Include or exclude channel 7
Excluded 0 Exclude
Included 1 Include
I RW CH8 Include or exclude channel 8
Excluded 0 Exclude
Included 1 Include
J RW CH9 Include or exclude channel 9
Excluded 0 Exclude
Included 1 Include
K RW CH10 Include or exclude channel 10
Excluded 0 Exclude
Included 1 Include
L RW CH11 Include or exclude channel 11
Excluded 0 Exclude
Included 1 Include
M RW CH12 Include or exclude channel 12
Excluded 0 Exclude
Included 1 Include
N RW CH13 Include or exclude channel 13
Excluded 0 Exclude
Included 1 Include
O RW CH14 Include or exclude channel 14
Excluded 0 Exclude
Included 1 Include
P RW CH15 Include or exclude channel 15
Excluded 0 Exclude
Included 1 Include
Q RW CH16 Include or exclude channel 16
Excluded 0 Exclude

4413_417 v1.9 444

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Included 1 Include
R RW CH17 Include or exclude channel 17
Excluded 0 Exclude
Included 1 Include
S RW CH18 Include or exclude channel 18
Excluded 0 Exclude
Included 1 Include
T RW CH19 Include or exclude channel 19
Excluded 0 Exclude
Included 1 Include
U RW CH20 Include or exclude channel 20
Excluded 0 Exclude
Included 1 Include
V RW CH21 Include or exclude channel 21
Excluded 0 Exclude
Included 1 Include
W RW CH22 Include or exclude channel 22
Excluded 0 Exclude
Included 1 Include
X RW CH23 Include or exclude channel 23
Excluded 0 Exclude
Included 1 Include
Y RW CH24 Include or exclude channel 24
Excluded 0 Exclude
Included 1 Include
Z RW CH25 Include or exclude channel 25
Excluded 0 Exclude
Included 1 Include
a RW CH26 Include or exclude channel 26
Excluded 0 Exclude
Included 1 Include
b RW CH27 Include or exclude channel 27
Excluded 0 Exclude
Included 1 Include
c RW CH28 Include or exclude channel 28
Excluded 0 Exclude
Included 1 Include
d RW CH29 Include or exclude channel 29
Excluded 0 Exclude
Included 1 Include
e RW CH30 Include or exclude channel 30
Excluded 0 Exclude
Included 1 Include
f RW CH31 Include or exclude channel 31
Excluded 0 Exclude
Included 1 Include

6.16.2.34 CHG[4]
Address offset: 0x810

4413_417 v1.9 445

 Peripherals

Channel group 4

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A
Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW CH0 Include or exclude channel 0
Excluded 0 Exclude
Included 1 Include
B RW CH1 Include or exclude channel 1
Excluded 0 Exclude
Included 1 Include
C RW CH2 Include or exclude channel 2
Excluded 0 Exclude
Included 1 Include
D RW CH3 Include or exclude channel 3
Excluded 0 Exclude
Included 1 Include
E RW CH4 Include or exclude channel 4
Excluded 0 Exclude
Included 1 Include
F RW CH5 Include or exclude channel 5
Excluded 0 Exclude
Included 1 Include
G RW CH6 Include or exclude channel 6
Excluded 0 Exclude
Included 1 Include
H RW CH7 Include or exclude channel 7
Excluded 0 Exclude
Included 1 Include
I RW CH8 Include or exclude channel 8
Excluded 0 Exclude
Included 1 Include
J RW CH9 Include or exclude channel 9
Excluded 0 Exclude
Included 1 Include
K RW CH10 Include or exclude channel 10
Excluded 0 Exclude
Included 1 Include
L RW CH11 Include or exclude channel 11
Excluded 0 Exclude
Included 1 Include
M RW CH12 Include or exclude channel 12
Excluded 0 Exclude
Included 1 Include
N RW CH13 Include or exclude channel 13
Excluded 0 Exclude
Included 1 Include
O RW CH14 Include or exclude channel 14
Excluded 0 Exclude
Included 1 Include
P RW CH15 Include or exclude channel 15
Excluded 0 Exclude
Included 1 Include

4413_417 v1.9 446

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Q RW CH16 Include or exclude channel 16
Excluded 0 Exclude
Included 1 Include
R RW CH17 Include or exclude channel 17
Excluded 0 Exclude
Included 1 Include
S RW CH18 Include or exclude channel 18
Excluded 0 Exclude
Included 1 Include
T RW CH19 Include or exclude channel 19
Excluded 0 Exclude
Included 1 Include
U RW CH20 Include or exclude channel 20
Excluded 0 Exclude
Included 1 Include
V RW CH21 Include or exclude channel 21
Excluded 0 Exclude
Included 1 Include
W RW CH22 Include or exclude channel 22
Excluded 0 Exclude
Included 1 Include
X RW CH23 Include or exclude channel 23
Excluded 0 Exclude
Included 1 Include
Y RW CH24 Include or exclude channel 24
Excluded 0 Exclude
Included 1 Include
Z RW CH25 Include or exclude channel 25
Excluded 0 Exclude
Included 1 Include
a RW CH26 Include or exclude channel 26
Excluded 0 Exclude
Included 1 Include
b RW CH27 Include or exclude channel 27
Excluded 0 Exclude
Included 1 Include
c RW CH28 Include or exclude channel 28
Excluded 0 Exclude
Included 1 Include
d RW CH29 Include or exclude channel 29
Excluded 0 Exclude
Included 1 Include
e RW CH30 Include or exclude channel 30
Excluded 0 Exclude
Included 1 Include
f RW CH31 Include or exclude channel 31
Excluded 0 Exclude
Included 1 Include

4413_417 v1.9 447

 Peripherals

6.16.2.35 CHG[5]
Address offset: 0x814
Channel group 5

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW CH0 Include or exclude channel 0
Excluded 0 Exclude
Included 1 Include
B RW CH1 Include or exclude channel 1
Excluded 0 Exclude
Included 1 Include
C RW CH2 Include or exclude channel 2
Excluded 0 Exclude
Included 1 Include
D RW CH3 Include or exclude channel 3
Excluded 0 Exclude
Included 1 Include
E RW CH4 Include or exclude channel 4
Excluded 0 Exclude
Included 1 Include
F RW CH5 Include or exclude channel 5
Excluded 0 Exclude
Included 1 Include
G RW CH6 Include or exclude channel 6
Excluded 0 Exclude
Included 1 Include
H RW CH7 Include or exclude channel 7
Excluded 0 Exclude
Included 1 Include
I RW CH8 Include or exclude channel 8
Excluded 0 Exclude
Included 1 Include
J RW CH9 Include or exclude channel 9
Excluded 0 Exclude
Included 1 Include
K RW CH10 Include or exclude channel 10
Excluded 0 Exclude
Included 1 Include
L RW CH11 Include or exclude channel 11
Excluded 0 Exclude
Included 1 Include
M RW CH12 Include or exclude channel 12
Excluded 0 Exclude
Included 1 Include
N RW CH13 Include or exclude channel 13
Excluded 0 Exclude
Included 1 Include
O RW CH14 Include or exclude channel 14
Excluded 0 Exclude

4413_417 v1.9 448

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Included 1 Include
P RW CH15 Include or exclude channel 15
Excluded 0 Exclude
Included 1 Include
Q RW CH16 Include or exclude channel 16
Excluded 0 Exclude
Included 1 Include
R RW CH17 Include or exclude channel 17
Excluded 0 Exclude
Included 1 Include
S RW CH18 Include or exclude channel 18
Excluded 0 Exclude
Included 1 Include
T RW CH19 Include or exclude channel 19
Excluded 0 Exclude
Included 1 Include
U RW CH20 Include or exclude channel 20
Excluded 0 Exclude
Included 1 Include
V RW CH21 Include or exclude channel 21
Excluded 0 Exclude
Included 1 Include
W RW CH22 Include or exclude channel 22
Excluded 0 Exclude
Included 1 Include
X RW CH23 Include or exclude channel 23
Excluded 0 Exclude
Included 1 Include
Y RW CH24 Include or exclude channel 24
Excluded 0 Exclude
Included 1 Include
Z RW CH25 Include or exclude channel 25
Excluded 0 Exclude
Included 1 Include
a RW CH26 Include or exclude channel 26
Excluded 0 Exclude
Included 1 Include
b RW CH27 Include or exclude channel 27
Excluded 0 Exclude
Included 1 Include
c RW CH28 Include or exclude channel 28
Excluded 0 Exclude
Included 1 Include
d RW CH29 Include or exclude channel 29
Excluded 0 Exclude
Included 1 Include
e RW CH30 Include or exclude channel 30
Excluded 0 Exclude
Included 1 Include
f RW CH31 Include or exclude channel 31

4413_417 v1.9 449

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID f e d c b a Z Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Excluded 0 Exclude
Included 1 Include

6.16.2.36 FORK[0]
Fork
This fork provides a second set of task endpoints for each of the channels in the PPI.

6.16.2.36.1 FORK[0].TEP
Address offset: 0x910
Channel 0 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register

6.16.2.37 FORK[1]
Fork
This fork provides a second set of task endpoints for each of the channels in the PPI.

6.16.2.37.1 FORK[1].TEP
Address offset: 0x914
Channel 1 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register

6.16.2.38 FORK[2]
Fork
This fork provides a second set of task endpoints for each of the channels in the PPI.

6.16.2.38.1 FORK[2].TEP
Address offset: 0x918
Channel 2 task endpoint

4413_417 v1.9 450

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register

6.16.2.39 FORK[3]
Fork
This fork provides a second set of task endpoints for each of the channels in the PPI.

6.16.2.39.1 FORK[3].TEP
Address offset: 0x91C
Channel 3 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register

6.16.2.40 FORK[4]
Fork
This fork provides a second set of task endpoints for each of the channels in the PPI.

6.16.2.40.1 FORK[4].TEP
Address offset: 0x920
Channel 4 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register

6.16.2.41 FORK[5]
Fork
This fork provides a second set of task endpoints for each of the channels in the PPI.

6.16.2.41.1 FORK[5].TEP
Address offset: 0x924
Channel 5 task endpoint

4413_417 v1.9 451

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register

6.16.2.42 FORK[6]
Fork
This fork provides a second set of task endpoints for each of the channels in the PPI.

6.16.2.42.1 FORK[6].TEP
Address offset: 0x928
Channel 6 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register

6.16.2.43 FORK[7]
Fork
This fork provides a second set of task endpoints for each of the channels in the PPI.

6.16.2.43.1 FORK[7].TEP
Address offset: 0x92C
Channel 7 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register

6.16.2.44 FORK[8]
Fork
This fork provides a second set of task endpoints for each of the channels in the PPI.

6.16.2.44.1 FORK[8].TEP
Address offset: 0x930
Channel 8 task endpoint

4413_417 v1.9 452

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register

6.16.2.45 FORK[9]
Fork
This fork provides a second set of task endpoints for each of the channels in the PPI.

6.16.2.45.1 FORK[9].TEP
Address offset: 0x934
Channel 9 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register

6.16.2.46 FORK[10]
Fork
This fork provides a second set of task endpoints for each of the channels in the PPI.

6.16.2.46.1 FORK[10].TEP
Address offset: 0x938
Channel 10 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register

6.16.2.47 FORK[11]
Fork
This fork provides a second set of task endpoints for each of the channels in the PPI.

6.16.2.47.1 FORK[11].TEP
Address offset: 0x93C
Channel 11 task endpoint

4413_417 v1.9 453

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register

6.16.2.48 FORK[12]
Fork
This fork provides a second set of task endpoints for each of the channels in the PPI.

6.16.2.48.1 FORK[12].TEP
Address offset: 0x940
Channel 12 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register

6.16.2.49 FORK[13]
Fork
This fork provides a second set of task endpoints for each of the channels in the PPI.

6.16.2.49.1 FORK[13].TEP
Address offset: 0x944
Channel 13 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register

6.16.2.50 FORK[14]
Fork
This fork provides a second set of task endpoints for each of the channels in the PPI.

6.16.2.50.1 FORK[14].TEP
Address offset: 0x948
Channel 14 task endpoint

4413_417 v1.9 454

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register

6.16.2.51 FORK[15]
Fork
This fork provides a second set of task endpoints for each of the channels in the PPI.

6.16.2.51.1 FORK[15].TEP
Address offset: 0x94C
Channel 15 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register

6.16.2.52 FORK[16]
Fork
This fork provides a second set of task endpoints for each of the channels in the PPI.

6.16.2.52.1 FORK[16].TEP
Address offset: 0x950
Channel 16 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register

6.16.2.53 FORK[17]
Fork
This fork provides a second set of task endpoints for each of the channels in the PPI.

6.16.2.53.1 FORK[17].TEP
Address offset: 0x954
Channel 17 task endpoint

4413_417 v1.9 455

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register

6.16.2.54 FORK[18]
Fork
This fork provides a second set of task endpoints for each of the channels in the PPI.

6.16.2.54.1 FORK[18].TEP
Address offset: 0x958
Channel 18 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register

6.16.2.55 FORK[19]
Fork
This fork provides a second set of task endpoints for each of the channels in the PPI.

6.16.2.55.1 FORK[19].TEP
Address offset: 0x95C
Channel 19 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register

6.16.2.56 FORK[20]
Fork
This fork provides a second set of task endpoints for each of the channels in the PPI.

6.16.2.56.1 FORK[20].TEP
Address offset: 0x960
Channel 20 task endpoint

4413_417 v1.9 456

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register

6.16.2.57 FORK[21]
Fork
This fork provides a second set of task endpoints for each of the channels in the PPI.

6.16.2.57.1 FORK[21].TEP
Address offset: 0x964
Channel 21 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register

6.16.2.58 FORK[22]
Fork
This fork provides a second set of task endpoints for each of the channels in the PPI.

6.16.2.58.1 FORK[22].TEP
Address offset: 0x968
Channel 22 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register

6.16.2.59 FORK[23]
Fork
This fork provides a second set of task endpoints for each of the channels in the PPI.

6.16.2.59.1 FORK[23].TEP
Address offset: 0x96C
Channel 23 task endpoint

4413_417 v1.9 457

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register

6.16.2.60 FORK[24]
Fork
This fork provides a second set of task endpoints for each of the channels in the PPI.

6.16.2.60.1 FORK[24].TEP
Address offset: 0x970
Channel 24 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register

6.16.2.61 FORK[25]
Fork
This fork provides a second set of task endpoints for each of the channels in the PPI.

6.16.2.61.1 FORK[25].TEP
Address offset: 0x974
Channel 25 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register

6.16.2.62 FORK[26]
Fork
This fork provides a second set of task endpoints for each of the channels in the PPI.

6.16.2.62.1 FORK[26].TEP
Address offset: 0x978
Channel 26 task endpoint

4413_417 v1.9 458

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register

6.16.2.63 FORK[27]
Fork
This fork provides a second set of task endpoints for each of the channels in the PPI.

6.16.2.63.1 FORK[27].TEP
Address offset: 0x97C
Channel 27 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register

6.16.2.64 FORK[28]
Fork
This fork provides a second set of task endpoints for each of the channels in the PPI.

6.16.2.64.1 FORK[28].TEP
Address offset: 0x980
Channel 28 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register

6.16.2.65 FORK[29]
Fork
This fork provides a second set of task endpoints for each of the channels in the PPI.

6.16.2.65.1 FORK[29].TEP
Address offset: 0x984
Channel 29 task endpoint

4413_417 v1.9 459

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register

6.16.2.66 FORK[30]
Fork
This fork provides a second set of task endpoints for each of the channels in the PPI.

6.16.2.66.1 FORK[30].TEP
Address offset: 0x988
Channel 30 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register

6.16.2.67 FORK[31]
Fork
This fork provides a second set of task endpoints for each of the channels in the PPI.

6.16.2.67.1 FORK[31].TEP
Address offset: 0x98C
Channel 31 task endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TEP Pointer to task register

6.17 PWM — Pulse width modulation

The pulse with modulation (PWM) module enables the generation of pulse width modulated signals
on GPIO. The module implements an up or up-and-down counter with four PWM channels that drive
assigned GPIOs.
The following are the main features of a PWM module:
• Programmable PWM frequency
• Up to four PWM channels with individual polarity and duty cycle values
• Edge or center-aligned pulses across PWM channels
• Multiple duty cycle arrays (sequences) defined in RAM
• Autonomous and glitch-free update of duty cycle values directly from memory through EasyDMA (no
CPU involvement)

4413_417 v1.9 460

 Peripherals

• Change of polarity, duty cycle, and base frequency possibly on every PWM period
• RAM sequences can be repeated or connected into loops
Sequence 0

DATA RAM Sequence 1

PWM
START STARTED

EasyDMA
STOP STOPPED
SEQSTART[0]
SEQSTART[1]
SEQSTARTED[0]
SEQ[n].REFRESH SEQSTARTED[1]
Decoder SEQEND[0]
NEXTSTEP
SEQEND[1]

COMP0 PSEL.OUT[0]

COMP1 PSEL.OUT[1]

COMP2 PSEL.OUT[2]

COMP3 PSEL.OUT[3]

Carry/Reload
Wave Counter COUNTERTOP

PWM_CLK PRESCALER

Figure 76: PWM module

6.17.1 Wave counter

The wave counter is responsible for generating the pulses at a duty cycle that depends on the compare
values, and at a frequency that depends on COUNTERTOP.
There is one common 15-bit counter with four compare channels. Thus, all four channels will share the
same period (PWM frequency), but can have individual duty cycle and polarity. The polarity is set by the
most significant bit (MSB) of the value read from RAM (see figure Decoder memory access modes on
page 464). When the MSB bit is high (FallingEdge polarity), OUT[n] starts high to become low during the
given PWM cycle, whereas the inverse occurs for RisingEdge polarity. Whether the counter counts up, or
up and down, is controlled by the MODE register.
The timer top value is controlled by the COUNTERTOP register. This register value, in conjunction with the
selected PRESCALER of the PWM_CLK, will result in a given PWM period. A COUNTERTOP value smaller
than the compare setting will result in a state where no PWM edges are generated. OUT[n] is held high,
given that the polarity is set to FallingEdge. All compare registers are internal and can only be configured
through decoder presented later. COUNTERTOP can be safely written at any time.
Sampling follows the START task. If DECODER.LOAD=WaveForm, the register value is ignored and taken
from RAM instead (see section Decoder with EasyDMA on page 464 for more details). If DECODER.LOAD
is anything else than the WaveForm, it is sampled following a STARTSEQ[n] task and when loading a new
value from RAM during a sequence playback.
The following figure shows the counter operating in up mode (MODE=PWM_MODE_Up), with two PWM
channels with the same frequency but different duty cycle:

4413_417 v1.9 461

 Peripherals

COUNTERTOP

COMP1

COMP0

OUT[0]

OUT[1]

Figure 77: PWM counter in up mode example - RisingEdge polarity

The counter is automatically reset to zero when COUNTERTOP is reached and OUT[n] will invert. OUT[n]
is held low if the compare value is 0 and held high if set to COUNTERTOP, given that the polarity is set to
FallingEdge. Counter running in up mode results in pulse widths that are edge-aligned. The following is the
code for the counter in up mode example:

uint16_t pwm_seq[4] = {PWM_CH0_DUTY, PWM_CH1_DUTY, PWM_CH2_DUTY, PWM_CH3_DUTY};

NRF_PWM0->PSEL.OUT[0] = (first_pin << PWM_PSEL_OUT_PIN_Pos) |
(PWM_PSEL_OUT_CONNECT_Connected <<
PWM_PSEL_OUT_CONNECT_Pos);
NRF_PWM0->PSEL.OUT[1] = (second_pin << PWM_PSEL_OUT_PIN_Pos) |
(PWM_PSEL_OUT_CONNECT_Connected <<
PWM_PSEL_OUT_CONNECT_Pos);
NRF_PWM0->ENABLE = (PWM_ENABLE_ENABLE_Enabled << PWM_ENABLE_ENABLE_Pos);
NRF_PWM0->MODE = (PWM_MODE_UPDOWN_Up << PWM_MODE_UPDOWN_Pos);
NRF_PWM0->PRESCALER = (PWM_PRESCALER_PRESCALER_DIV_1 <<
PWM_PRESCALER_PRESCALER_Pos);
NRF_PWM0->COUNTERTOP = (16000 << PWM_COUNTERTOP_COUNTERTOP_Pos); //1 msec
NRF_PWM0->LOOP = (PWM_LOOP_CNT_Disabled << PWM_LOOP_CNT_Pos);
NRF_PWM0->DECODER = (PWM_DECODER_LOAD_Individual << PWM_DECODER_LOAD_Pos) |
(PWM_DECODER_MODE_RefreshCount << PWM_DECODER_MODE_Pos);
NRF_PWM0->SEQ[0].PTR = ((uint32_t)(pwm_seq) << PWM_SEQ_PTR_PTR_Pos);
NRF_PWM0->SEQ[0].CNT = ((sizeof(pwm_seq) / sizeof(uint16_t)) <<
PWM_SEQ_CNT_CNT_Pos);
NRF_PWM0->SEQ[0].REFRESH = 0;
NRF_PWM0->SEQ[0].ENDDELAY = 0;
NRF_PWM0->TASKS_SEQSTART[0] = 1;

When the counter is running in up mode, the following formula can be used to compute the PWM period
and the step size:
PWM period: TPWM(Up)= TPWM_CLK * COUNTERTOP
Step width/Resolution: Tsteps= TPWM_CLK

4413_417 v1.9 462

 Peripherals

The following figure shows the counter operating in up-and-down mode

(MODE=PWM_MODE_UpAndDown), with two PWM channels with the same frequency but different duty
cycle and output polarity:

COUNTERTOP

COMP1

COMP0

OUT[0]

OUT[1]

Figure 78: PWM counter in up-and-down mode example

The counter starts decrementing to zero when COUNTERTOP is reached and will invert the OUT[n] when
compare value is hit for the second time. This results in a set of pulses that are center-aligned. The
following is the code for the counter in up-and-down mode example:

uint16_t pwm_seq[4] = {PWM_CH0_DUTY, PWM_CH1_DUTY, PWM_CH2_DUTY, PWM_CH3_DUTY};

NRF_PWM0->PSEL.OUT[0] = (first_pin << PWM_PSEL_OUT_PIN_Pos) |
(PWM_PSEL_OUT_CONNECT_Connected <<
PWM_PSEL_OUT_CONNECT_Pos);
NRF_PWM0->PSEL.OUT[1] = (second_pin << PWM_PSEL_OUT_PIN_Pos) |
(PWM_PSEL_OUT_CONNECT_Connected <<
PWM_PSEL_OUT_CONNECT_Pos);
NRF_PWM0->ENABLE = (PWM_ENABLE_ENABLE_Enabled << PWM_ENABLE_ENABLE_Pos);
NRF_PWM0->MODE = (PWM_MODE_UPDOWN_UpAndDown << PWM_MODE_UPDOWN_Pos);
NRF_PWM0->PRESCALER = (PWM_PRESCALER_PRESCALER_DIV_1 <<
PWM_PRESCALER_PRESCALER_Pos);
NRF_PWM0->COUNTERTOP = (16000 << PWM_COUNTERTOP_COUNTERTOP_Pos); //1 msec
NRF_PWM0->LOOP = (PWM_LOOP_CNT_Disabled << PWM_LOOP_CNT_Pos);
NRF_PWM0->DECODER = (PWM_DECODER_LOAD_Individual << PWM_DECODER_LOAD_Pos) |
(PWM_DECODER_MODE_RefreshCount << PWM_DECODER_MODE_Pos);
NRF_PWM0->SEQ[0].PTR = ((uint32_t)(pwm_seq) << PWM_SEQ_PTR_PTR_Pos);
NRF_PWM0->SEQ[0].CNT = ((sizeof(pwm_seq) / sizeof(uint16_t)) <<
PWM_SEQ_CNT_CNT_Pos);
NRF_PWM0->SEQ[0].REFRESH = 0;
NRF_PWM0->SEQ[0].ENDDELAY = 0;
NRF_PWM0->TASKS_SEQSTART[0] = 1;

When the counter is running in up-and-down mode, the following formula can be used to compute the
PWM period and the step size:
TPWM(Up And Down) = TPWM_CLK * 2 * COUNTERTOP
Step width/Resolution: Tsteps = TPWM_CLK * 2

4413_417 v1.9 463

 Peripherals

6.17.2 Decoder with EasyDMA

The decoder uses EasyDMA to take PWM parameters stored in RAM and update the internal compare
registers of the wave counter, based on the mode of operation.
PWM parameters are organized into a sequence containing at least one half word (16 bit). Its most
significant bit[15] denotes the polarity of the OUT[n] while bit[14:0] is the 15-bit compare value.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

Id B A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Id RW Field Value Id Value Description
A RW COMPARE Duty cycle setting - value loaded to internal compare
register
B RW POLARITY Edge polarity of GPIO.
RisingEdge 0 First edge within the PWM period is rising
FallingEdge 1 First edge within the PWM period is falling

The DECODER register controls how the RAM content is interpreted and loaded into the internal compare
registers. The LOAD field controls if the RAM values are loaded to all compare channels, or to update a
group or all channels with individual values. The following figure illustrates how parameters stored in RAM
are organized and routed to various compare channels in different modes:
DECODER.LOAD=Common DECODER.LOAD=Grouped DECODER.LOAD=Single

P COMP0 P P
SEQ[n].PTR O COMPARE COMP1 O COMPARE COMP0 O COMPARE COMP0
COMP2 COMP1
L COMP3 L L
P COMP0 P P
O COMPARE COMP1 O COMPARE COMP2 O COMPARE COMP1
COMP2 COMP3
L COMP3 L L
Increasing Data P
RAM address
... ... O COMPARE COMP2
L
P COMP0 P P
O COMPARE COMP1 O COMPARE COMP0 O COMPARE COMP3
COMP2 COMP1
L COMP3 L L

DECODER.LOAD=WaveForm

P
O COMPARE COMP0
L
P
O COMPARE COMP1
L
P
O COMPARE COMP2
L

TOP COUNTERTOP

Figure 79: Decoder memory access modes

A special mode of operation is available when DECODER.LOAD is set to WaveForm. In this mode, up to
three PWM channels can be enabled - OUT[0] to OUT[2]. In RAM, four values are loaded at a time: the
first, second and third location are used to load the values, and the fourth RAM location is used to load
the COUNTERTOP register. This way one can have up to three PWM channels with a frequency base that
changes on a per PWM period basis. This mode of operation is useful for arbitrary wave form generation
in applications, such as LED lighting.

4413_417 v1.9 464

 Peripherals

The register SEQ[n].REFRESH=N (one per sequence n=0 or 1) will instruct a new RAM stored pulse width
value on every (N+1)th PWM period. Setting the register to zero will result in a new duty cycle update
every PWM period, as long as the minimum PWM period is observed.
Note that registers SEQ[n].REFRESH and SEQ[n].ENDDELAY are ignored when DECODER.MODE=NextStep.
The next value is loaded upon every received NEXTSTEP task.
SEQ[n].PTR is the pointer used to fetch COMPARE values from RAM. If the SEQ[n].PTR is not pointing to
a RAM region, an EasyDMA transfer may result in a HardFault or RAM corruption. See Memory on page
21 for more information about the different memory regions. After the SEQ[n].PTR is set to the desired
RAM location, the SEQ[n].CNT register must be set to number of 16-bit half words in the sequence. It is
important to observe that the Grouped mode requires one half word per group, while the Single mode
requires one half word per channel, thus increasing the RAM size occupation. If PWM generation is not
running when the SEQSTART[n] task is triggered, the task will load the first value from RAM and then start
the PWM generation. A SEQSTARTED[n] event is generated as soon as the EasyDMA has read the first
PWM parameter from RAM and the wave counter has started executing it. When LOOP.CNT=0, sequence
n=0 or 1 is played back once. After the last value in the sequence has been loaded and started executing,
a SEQEND[n] event is generated. The PWM generation will then continue with the last loaded value. The
following figure illustrates an example of such simple playback:

SEQ[0].CNT=4, SEQ[0].REFRESH=0, SEQ[0].ENDDELAY=0, LOOP.CNT=0 Continues with last setting

P P P P
COMPARE COMPARE COMPARE COMPARE
SEQ[0].PTR O O O O
0 1 2 3
L L L L

Event/Tasks PWM pulse period

SEQSTART[0] SEQSTARTED[0] SEQEND[0]

Figure 80: Simple sequence example

4413_417 v1.9 465

 Peripherals

Figure depicts the source code used for configuration and timing details in a sequence where only
sequence 0 is used and only run once with a new PWM duty cycle for each period.

NRF_PWM0->PSEL.OUT[0] = (first_pin << PWM_PSEL_OUT_PIN_Pos) |

(PWM_PSEL_OUT_CONNECT_Connected <<
PWM_PSEL_OUT_CONNECT_Pos);
NRF_PWM0->ENABLE = (PWM_ENABLE_ENABLE_Enabled << PWM_ENABLE_ENABLE_Pos);
NRF_PWM0->MODE = (PWM_MODE_UPDOWN_Up << PWM_MODE_UPDOWN_Pos);
NRF_PWM0->PRESCALER = (PWM_PRESCALER_PRESCALER_DIV_1 <<
PWM_PRESCALER_PRESCALER_Pos);
NRF_PWM0->COUNTERTOP = (16000 << PWM_COUNTERTOP_COUNTERTOP_Pos); //1 msec
NRF_PWM0->LOOP = (PWM_LOOP_CNT_Disabled << PWM_LOOP_CNT_Pos);
NRF_PWM0->DECODER = (PWM_DECODER_LOAD_Common << PWM_DECODER_LOAD_Pos) |
(PWM_DECODER_MODE_RefreshCount << PWM_DECODER_MODE_Pos);
NRF_PWM0->SEQ[0].PTR = ((uint32_t)(seq0_ram) << PWM_SEQ_PTR_PTR_Pos);
NRF_PWM0->SEQ[0].CNT = ((sizeof(seq0_ram) / sizeof(uint16_t)) <<
PWM_SEQ_CNT_CNT_Pos);
NRF_PWM0->SEQ[0].REFRESH = 0;
NRF_PWM0->SEQ[0].ENDDELAY = 0;
NRF_PWM0->TASKS_SEQSTART[0] = 1;

To completely stop the PWM generation and force the associated pins to a defined state, a STOP task can
be triggered at any time. A STOPPED event is generated when the PWM generation has stopped at the
end of currently running PWM period, and the pins go into their idle state as defined in GPIO OUT register.
PWM generation can then only be restarted through a SEQSTART[n] task. SEQSTART[n] will resume PWM
generation after having loaded the first value from the RAM buffer defined in the SEQ[n].PTR register.
The table below indicates when specific registers get sampled by the hardware. Care should be taken
when updating these registers to avoid that values are applied earlier than expected.

4413_417 v1.9 466

 Peripherals

Register Taken into account by hardware Recommended (safe) update

SEQ[n].PTR When sending the SEQSTART[n] task After having received the SEQSTARTED[n] event
SEQ[n].CNT When sending the SEQSTART[n] task After having received the SEQSTARTED[n] event
SEQ[0].ENDDELAY When sending the SEQSTART[0] task Before starting sequence [0] through a SEQSTART[0] task

Every time a new value from sequence [0] has been loaded from When no more value from sequence [0] gets loaded from RAM
RAM and gets applied to the Wave Counter (indicated by the (indicated by the SEQEND[0] event)
PWMPERIODEND event)
At any time during sequence [1] (which starts when the
SEQSTARTED[1] event is generated)
SEQ[1].ENDDELAY When sending the SEQSTART[1] task Before starting sequence [1] through a SEQSTART[1] task

Every time a new value from sequence [1] has been loaded from When no more value from sequence [1] gets loaded from RAM
RAM and gets applied to the Wave Counter (indicated by the (indicated by the SEQEND[1] event)
PWMPERIODEND event)
At any time during sequence [0] (which starts when the
SEQSTARTED[0] event is generated)
SEQ[0].REFRESH When sending the SEQSTART[0] task Before starting sequence [0] through a SEQSTART[0] task

Every time a new value from sequence [0] has been loaded from At any time during sequence [1] (which starts when the
RAM and gets applied to the Wave Counter (indicated by the SEQSTARTED[1] event is generated)
PWMPERIODEND event)
SEQ[1].REFRESH When sending the SEQSTART[1] task Before starting sequence [1] through a SEQSTART[1] task

Every time a new value from sequence [1] has been loaded from At any time during sequence [0] (which starts when the
RAM and gets applied to the Wave Counter (indicated by the SEQSTARTED[0] event is generated)
PWMPERIODEND event)
COUNTERTOP In DECODER.LOAD=WaveForm: this register is ignored. Before starting PWM generation through a SEQSTART[n] task

In all other LOAD modes: at the end of current PWM period After a STOP task has been triggered, and the STOPPED event has
(indicated by the PWMPERIODEND event) been received.
MODE Immediately Before starting PWM generation through a SEQSTART[n] task

After a STOP task has been triggered, and the STOPPED event has
been received.
DECODER Immediately Before starting PWM generation through a SEQSTART[n] task

After a STOP task has been triggered, and the STOPPED event has
been received.
PRESCALER Immediately Before starting PWM generation through a SEQSTART[n] task

After a STOP task has been triggered, and the STOPPED event has
been received.
LOOP Immediately Before starting PWM generation through a SEQSTART[n] task

After a STOP task has been triggered, and the STOPPED event has
been received.
PSEL.OUT[n] Immediately Before enabling the PWM instance through the ENABLE register

Table 30: When to safely update PWM registers

Note: SEQ[n].REFRESH and SEQ[n].ENDDELAY are ignored at the end of a complex sequence,
indicated by a LOOPSDONE event. The reason for this is that the last value loaded from RAM
is maintained until further action from software (restarting a new sequence, or stopping PWM
generation).

A more complex example, where LOOP.CNT>0, is shown in the following figure:

4413_417 v1.9 467

 Peripherals

SEQ[0].CNT=2, SEQ[1].CNT=3, SEQ[0].REFRESH=1, SEQ[1].REFRESH=0, SEQ[0].ENDDELAY=1, SEQ[1].ENDDELAY=0, LOOP.CNT=1

P P
SEQ[0].PTR O COMPARE O COMPARE
L L

Event/Tasks PWM clock period

(continued below)

SEQSTART[0] SEQSTARTED[0] SEQEND[0]

PWM generation maintains

P P last played value
SEQ[1].PTR O COMPARE O COMPARE
L L
1 PWM period
SEQ[0].ENDDELAY=1

Event/Tasks
(continuation)

SEQSTARTED[1] SEQEND[1] LOOPSDONE

Figure 81: Example using two sequences

In this case, an automated playback takes place, consisting of SEQ[0], delay 0, SEQ[1], delay 1, then again
SEQ[0], etc. The user can choose to start a complex playback with SEQ[0] or SEQ[1] through sending the
SEQSTART[0] or SEQSTART[1] task. The complex playback always ends with delay 1.
The two sequences 0 and 1 are defined by the addresses of value tables in RAM (pointed to by
SEQ[n].PTR) and the buffer size (SEQ[n].CNT). The rate at which a new value is loaded is defined
individually for each sequence by SEQ[n].REFRESH. The chaining of sequence 1 following the sequence 0 is
implicit, the LOOP.CNT register allows the chaining of sequence 1 to sequence 0 for a determined number
of times. In other words, it allows to repeat a complex sequence a number of times in a fully automated
way.
In the following code example, sequence 0 is defined with SEQ[0].REFRESH set to 1, meaning that a
new PWM duty cycle is pushed every second PWM period. This complex sequence is started with the
SEQSTART[0] task, so SEQ[0] is played first. Since SEQ[0].ENDDELAY=1 there will be one PWM period delay
between last period on sequence 0 and the first period on sequence 1. Since SEQ[1].ENDDELAY=0 there
is no delay 1, so SEQ[0] would be started immediately after the end of SEQ[1]. However, as LOOP.CNT is

4413_417 v1.9 468

 Peripherals

1, the playback stops after having played SEQ[1] only once, and both SEQEND[1] and LOOPSDONE are
generated (their order is not guaranteed in this case).

NRF_PWM0->PSEL.OUT[0] = (first_pin << PWM_PSEL_OUT_PIN_Pos) |

(PWM_PSEL_OUT_CONNECT_Connected <<
PWM_PSEL_OUT_CONNECT_Pos);
NRF_PWM0->ENABLE = (PWM_ENABLE_ENABLE_Enabled << PWM_ENABLE_ENABLE_Pos);
NRF_PWM0->MODE = (PWM_MODE_UPDOWN_Up << PWM_MODE_UPDOWN_Pos);
NRF_PWM0->PRESCALER = (PWM_PRESCALER_PRESCALER_DIV_1 <<
PWM_PRESCALER_PRESCALER_Pos);
NRF_PWM0->COUNTERTOP = (16000 << PWM_COUNTERTOP_COUNTERTOP_Pos); //1 msec
NRF_PWM0->LOOP = (1 << PWM_LOOP_CNT_Pos);
NRF_PWM0->DECODER = (PWM_DECODER_LOAD_Common << PWM_DECODER_LOAD_Pos) |
(PWM_DECODER_MODE_RefreshCount << PWM_DECODER_MODE_Pos);
NRF_PWM0->SEQ[0].PTR = ((uint32_t)(seq0_ram) << PWM_SEQ_PTR_PTR_Pos);
NRF_PWM0->SEQ[0].CNT = ((sizeof(seq0_ram) / sizeof(uint16_t)) <<
PWM_SEQ_CNT_CNT_Pos);
NRF_PWM0->SEQ[0].REFRESH = 1;
NRF_PWM0->SEQ[0].ENDDELAY = 1;
NRF_PWM0->SEQ[1].PTR = ((uint32_t)(seq1_ram) << PWM_SEQ_PTR_PTR_Pos);
NRF_PWM0->SEQ[1].CNT = ((sizeof(seq1_ram) / sizeof(uint16_t)) <<
PWM_SEQ_CNT_CNT_Pos);
NRF_PWM0->SEQ[1].REFRESH = 0;
NRF_PWM0->SEQ[1].ENDDELAY = 0;
NRF_PWM0->TASKS_SEQSTART[0] = 1;

The decoder can also be configured to asynchronously load new PWM duty cycle. If the DECODER.MODE
register is set to NextStep, then the NEXTSTEP task will cause an update of internal compare registers on
the next PWM period.
The following figures provide an overview of each part of an arbitrary sequence, in various modes
(LOOP.CNT=0 and LOOP.CNT>0). In particular, the following are represented:
• Initial and final duty cycle on the PWM output(s)
• Chaining of SEQ[0] and SEQ[1] if LOOP.CNT>0
• Influence of registers on the sequence
• Events generated during a sequence
• DMA activity (loading of next value and applying it to the output(s))

4413_417 v1.9 469

4413_417 v1.9
cycle
Previously
loaded duty

New value load

0% duty cycle
100% duty cycle
TASKS_SEQSTART[0]

Loop counter
EVENTS_SEQSTARTED[0]
SEQ[0].CNT
EVENTS_SEQEND[0]
SEQ[0].ENDDELA
Y
EVENTS_SEQSTARTED[1]
SEQ[1].CNT

LOOP.CNT
EVENTS_SEQEND[1]
SEQ[1].ENDDELA
cycle
Previously
loaded duty

Y
New value load
0% duty cycle
100% duty cycle

EVENTS_SEQSTARTED[0]
TASKS_SEQSTART[0]
SEQ[0].CNT EVENTS_SEQSTARTED[0]
EVENTS_SEQEND[0] SEQ[0].CNT
SEQ[0].ENDDELA

470
EVENTS_SEQEND[0]
Y SEQ[0].ENDDELA
EVENTS_SEQSTARTED[1] Y
SEQ[1].CNT
EVENTS_SEQEND[1]

(LOOP.CNT - 1) ...
Figure 82: Single shot (LOOP.CNT=0)

EVENTS_SEQSTARTED[0]
duty cycle
last loaded

maintained

SEQ[0].CNT
EVENTS_SEQEND[0]
SEQ[0].ENDDELA
Y
1

EVENTS_SEQSTARTED[1]
SEQ[1].CNT

Figure 83: Complex sequence (LOOP.CNT>0) starting with SEQ[0]

EVENTS_SEQEND[1]
EVENTS_LOOPSDONE SEQ[1].ENDDELA
Y
Note: The single-shot example also applies to SEQ[1]. Only SEQ[0] is represented for simplicity.

duty cycle
last loaded

maintained
Peripherals
 Peripherals

Loop counter LOOP.CNT (LOOP.CNT - 1) ... 1

SEQ[1].ENDDELA

SEQ[0].ENDDELA

SEQ[0].ENDDELA

SEQ[1].ENDDELA
SEQ[1].CNT

SEQ[0].CNT

SEQ[1].CNT

SEQ[0].CNT

SEQ[1].CNT
Y

Y
100% duty cycle

Previously
loaded last loaded
duty cycle duty cycle
maintained

0% duty cycle

New value load

EVENTS_SEQEND[1]

EVENTS_SEQEND[0]

EVENTS_SEQEND[1]

EVENTS_SEQEND[0]

EVENTS_SEQEND[1]
EVENTS_LOOPSDONE
EVENTS_SEQSTARTED[1]

EVENTS_SEQSTARTED[0]

EVENTS_SEQSTARTED[1]

EVENTS_SEQSTARTED[0]

EVENTS_SEQSTARTED[1]
TASKS_SEQSTART[1]

Figure 84: Complex sequence (LOOP.CNT>0) starting with SEQ[1]

Note: If a sequence is in use in a simple or complex sequence, it must have a length of SEQ[n].CNT
> 0.

6.17.3 Limitations
Previous compare value is repeated if the PWM period is shorter than the time it takes for the EasyDMA
to retrieve from RAM and update the internal compare registers. This is to ensure a glitch-free operation
even for very short PWM periods.

6.17.4 Pin configuration

The OUT[n] (n=0..3) signals associated with each PWM channel are mapped to physical pins according to
the configuration of PSEL.OUT[n] registers. If PSEL.OUT[n].CONNECT is set to Disconnected, the associated
PWM module signal will not be connected to any physical pins.
The PSEL.OUT[n] registers and their configurations are used as long as the PWM module is enabled and
the PWM generation active (wave counter started). They are retained only as long as the device is in
System ON mode (see section POWER for more information about power modes).
To ensure correct behavior in the PWM module, the pins that are used must be configured in the GPIO
peripheral in the following way before the PWM module is enabled:

PWM signal PWM pin Direction Output value Comment

OUT[n] As specified in PSEL.OUT[n] Output 0 Idle state defined in GPIO OUT

(n=0..3) register

Table 31: Recommended GPIO configuration before starting PWM generation

4413_417 v1.9 471

 Peripherals

The idle state of a pin is defined by the OUT register in the GPIO module, to ensure that the pins used by
the PWM module are driven correctly. If PWM generation is stopped by triggering a STOP task, the PWM
module itself is temporarily disabled or the device temporarily enters System OFF. This configuration must
be retained in the GPIO for the selected pins (I/Os) for as long as the PWM module is supposed to be
connected to an external PWM circuit.
Only one peripheral can be assigned to drive a particular GPIO pin at a time. Failing to do so may result in
unpredictable behavior.

6.17.5 Registers
Instances

Instance Base address Description

PWM0 0x4001C000 Pulse width modulation unit 0
PWM1 0x40021000 Pulse width modulation unit 1
PWM2 0x40022000 Pulse width modulation unit 2
PWM3 0x4002D000 Pulse width modulation unit 3

Register overview

Register Offset Description

TASKS_STOP 0x004 Stops PWM pulse generation on all channels at the end of current PWM period, and stops sequence
playback
TASKS_SEQSTART[0] 0x008 Loads the first PWM value on all enabled channels from sequence 0, and starts playing that
sequence at the rate defined in SEQ[0]REFRESH and/or DECODER.MODE. Causes PWM generation to
start if not running.
TASKS_SEQSTART[1] 0x00C Loads the first PWM value on all enabled channels from sequence 1, and starts playing that
sequence at the rate defined in SEQ[1]REFRESH and/or DECODER.MODE. Causes PWM generation to
start if not running.
TASKS_NEXTSTEP 0x010 Steps by one value in the current sequence on all enabled channels if DECODER.MODE=NextStep.
Does not cause PWM generation to start if not running.
EVENTS_STOPPED 0x104 Response to STOP task, emitted when PWM pulses are no longer generated
EVENTS_SEQSTARTED[0] 0x108 First PWM period started on sequence 0
EVENTS_SEQSTARTED[1] 0x10C First PWM period started on sequence 1
EVENTS_SEQEND[0] 0x110 Emitted at end of every sequence 0, when last value from RAM has been applied to wave counter
EVENTS_SEQEND[1] 0x114 Emitted at end of every sequence 1, when last value from RAM has been applied to wave counter
EVENTS_PWMPERIODEND 0x118 Emitted at the end of each PWM period
EVENTS_LOOPSDONE 0x11C Concatenated sequences have been played the amount of times defined in LOOP.CNT
SHORTS 0x200 Shortcuts between local events and tasks
INTEN 0x300 Enable or disable interrupt
INTENSET 0x304 Enable interrupt
INTENCLR 0x308 Disable interrupt
ENABLE 0x500 PWM module enable register
MODE 0x504 Selects operating mode of the wave counter
COUNTERTOP 0x508 Value up to which the pulse generator counter counts
PRESCALER 0x50C Configuration for PWM_CLK
DECODER 0x510 Configuration of the decoder
LOOP 0x514 Number of playbacks of a loop
SEQ[0].PTR 0x520 Beginning address in RAM of this sequence
SEQ[0].CNT 0x524 Number of values (duty cycles) in this sequence
SEQ[0].REFRESH 0x528 Number of additional PWM periods between samples loaded into compare register
SEQ[0].ENDDELAY 0x52C Time added after the sequence

4413_417 v1.9 472

 Peripherals

Register Offset Description

SEQ[1].PTR 0x540 Beginning address in RAM of this sequence
SEQ[1].CNT 0x544 Number of values (duty cycles) in this sequence
SEQ[1].REFRESH 0x548 Number of additional PWM periods between samples loaded into compare register
SEQ[1].ENDDELAY 0x54C Time added after the sequence
PSEL.OUT[0] 0x560 Output pin select for PWM channel 0
PSEL.OUT[1] 0x564 Output pin select for PWM channel 1
PSEL.OUT[2] 0x568 Output pin select for PWM channel 2
PSEL.OUT[3] 0x56C Output pin select for PWM channel 3

6.17.5.1 TASKS_STOP
Address offset: 0x004
Stops PWM pulse generation on all channels at the end of current PWM period, and stops sequence
playback

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STOP Stops PWM pulse generation on all channels at the end of current PWM
period, and stops sequence playback
Trigger 1 Trigger task

6.17.5.2 TASKS_SEQSTART[0]
Address offset: 0x008
Loads the first PWM value on all enabled channels from sequence 0, and starts playing that sequence
at the rate defined in SEQ[0]REFRESH and/or DECODER.MODE. Causes PWM generation to start if not
running.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_SEQSTART Loads the first PWM value on all enabled channels from sequence 0, and
starts playing that sequence at the rate defined in SEQ[0]REFRESH and/or
DECODER.MODE. Causes PWM generation to start if not running.
Trigger 1 Trigger task

6.17.5.3 TASKS_SEQSTART[1]
Address offset: 0x00C
Loads the first PWM value on all enabled channels from sequence 1, and starts playing that sequence
at the rate defined in SEQ[1]REFRESH and/or DECODER.MODE. Causes PWM generation to start if not
running.

4413_417 v1.9 473

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_SEQSTART Loads the first PWM value on all enabled channels from sequence 1, and
starts playing that sequence at the rate defined in SEQ[1]REFRESH and/or
DECODER.MODE. Causes PWM generation to start if not running.
Trigger 1 Trigger task

6.17.5.4 TASKS_NEXTSTEP
Address offset: 0x010
Steps by one value in the current sequence on all enabled channels if DECODER.MODE=NextStep. Does
not cause PWM generation to start if not running.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_NEXTSTEP Steps by one value in the current sequence on all enabled channels if
DECODER.MODE=NextStep. Does not cause PWM generation to start if not
running.
Trigger 1 Trigger task

6.17.5.5 EVENTS_STOPPED
Address offset: 0x104
Response to STOP task, emitted when PWM pulses are no longer generated

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_STOPPED Response to STOP task, emitted when PWM pulses are no longer generated
NotGenerated 0 Event not generated
Generated 1 Event generated

6.17.5.6 EVENTS_SEQSTARTED[0]
Address offset: 0x108
First PWM period started on sequence 0

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_SEQSTARTED First PWM period started on sequence 0
NotGenerated 0 Event not generated
Generated 1 Event generated

4413_417 v1.9 474

 Peripherals

6.17.5.7 EVENTS_SEQSTARTED[1]
Address offset: 0x10C
First PWM period started on sequence 1

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_SEQSTARTED First PWM period started on sequence 1
NotGenerated 0 Event not generated
Generated 1 Event generated

6.17.5.8 EVENTS_SEQEND[0]
Address offset: 0x110
Emitted at end of every sequence 0, when last value from RAM has been applied to wave counter

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_SEQEND Emitted at end of every sequence 0, when last value from RAM has been
applied to wave counter
NotGenerated 0 Event not generated
Generated 1 Event generated

6.17.5.9 EVENTS_SEQEND[1]
Address offset: 0x114
Emitted at end of every sequence 1, when last value from RAM has been applied to wave counter

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_SEQEND Emitted at end of every sequence 1, when last value from RAM has been
applied to wave counter
NotGenerated 0 Event not generated
Generated 1 Event generated

6.17.5.10 EVENTS_PWMPERIODEND
Address offset: 0x118
Emitted at the end of each PWM period

4413_417 v1.9 475

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_PWMPERIODEND Emitted at the end of each PWM period
NotGenerated 0 Event not generated
Generated 1 Event generated

6.17.5.11 EVENTS_LOOPSDONE
Address offset: 0x11C
Concatenated sequences have been played the amount of times defined in LOOP.CNT

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_LOOPSDONE Concatenated sequences have been played the amount of times defined in
LOOP.CNT
NotGenerated 0 Event not generated
Generated 1 Event generated

6.17.5.12 SHORTS
Address offset: 0x200
Shortcuts between local events and tasks

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW SEQEND0_STOP Shortcut between event SEQEND[0] and task STOP
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
B RW SEQEND1_STOP Shortcut between event SEQEND[1] and task STOP
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
C RW LOOPSDONE_SEQSTART0 Shortcut between event LOOPSDONE and task SEQSTART[0]
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
D RW LOOPSDONE_SEQSTART1 Shortcut between event LOOPSDONE and task SEQSTART[1]
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
E RW LOOPSDONE_STOP Shortcut between event LOOPSDONE and task STOP
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut

6.17.5.13 INTEN
Address offset: 0x300
Enable or disable interrupt

4413_417 v1.9 476

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID H G F E D C B

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
B RW STOPPED Enable or disable interrupt for event STOPPED
Disabled 0 Disable
Enabled 1 Enable
C RW SEQSTARTED[0] Enable or disable interrupt for event SEQSTARTED[0]
Disabled 0 Disable
Enabled 1 Enable
D RW SEQSTARTED[1] Enable or disable interrupt for event SEQSTARTED[1]
Disabled 0 Disable
Enabled 1 Enable
E RW SEQEND[0] Enable or disable interrupt for event SEQEND[0]
Disabled 0 Disable
Enabled 1 Enable
F RW SEQEND[1] Enable or disable interrupt for event SEQEND[1]
Disabled 0 Disable
Enabled 1 Enable
G RW PWMPERIODEND Enable or disable interrupt for event PWMPERIODEND
Disabled 0 Disable
Enabled 1 Enable
H RW LOOPSDONE Enable or disable interrupt for event LOOPSDONE
Disabled 0 Disable
Enabled 1 Enable

6.17.5.14 INTENSET
Address offset: 0x304
Enable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID H G F E D C B

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
B RW STOPPED Write '1' to enable interrupt for event STOPPED
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW SEQSTARTED[0] Write '1' to enable interrupt for event SEQSTARTED[0]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
D RW SEQSTARTED[1] Write '1' to enable interrupt for event SEQSTARTED[1]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
E RW SEQEND[0] Write '1' to enable interrupt for event SEQEND[0]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
F RW SEQEND[1] Write '1' to enable interrupt for event SEQEND[1]
Set 1 Enable

4413_417 v1.9 477

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID H G F E D C B

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
G RW PWMPERIODEND Write '1' to enable interrupt for event PWMPERIODEND
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
H RW LOOPSDONE Write '1' to enable interrupt for event LOOPSDONE
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.17.5.15 INTENCLR
Address offset: 0x308
Disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID H G F E D C B

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
B RW STOPPED Write '1' to disable interrupt for event STOPPED
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW SEQSTARTED[0] Write '1' to disable interrupt for event SEQSTARTED[0]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
D RW SEQSTARTED[1] Write '1' to disable interrupt for event SEQSTARTED[1]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
E RW SEQEND[0] Write '1' to disable interrupt for event SEQEND[0]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
F RW SEQEND[1] Write '1' to disable interrupt for event SEQEND[1]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
G RW PWMPERIODEND Write '1' to disable interrupt for event PWMPERIODEND
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
H RW LOOPSDONE Write '1' to disable interrupt for event LOOPSDONE
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

4413_417 v1.9 478

 Peripherals

6.17.5.16 ENABLE
Address offset: 0x500
PWM module enable register

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW ENABLE Enable or disable PWM module
Disabled 0 Disabled
Enabled 1 Enable

6.17.5.17 MODE
Address offset: 0x504
Selects operating mode of the wave counter

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW UPDOWN Selects up mode or up-and-down mode for the counter
Up 0 Up counter, edge-aligned PWM duty cycle
UpAndDown 1 Up and down counter, center-aligned PWM duty cycle

6.17.5.18 COUNTERTOP
Address offset: 0x508
Value up to which the pulse generator counter counts

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A

Reset 0x000003FF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW COUNTERTOP [3..32767] Value up to which the pulse generator counter counts. This register is
ignored when DECODER.MODE=WaveForm and only values from RAM are
used.

6.17.5.19 PRESCALER
Address offset: 0x50C
Configuration for PWM_CLK

4413_417 v1.9 479

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PRESCALER Prescaler of PWM_CLK
DIV_1 0 Divide by 1 (16 MHz)
DIV_2 1 Divide by 2 (8 MHz)
DIV_4 2 Divide by 4 (4 MHz)
DIV_8 3 Divide by 8 (2 MHz)
DIV_16 4 Divide by 16 (1 MHz)
DIV_32 5 Divide by 32 (500 kHz)
DIV_64 6 Divide by 64 (250 kHz)
DIV_128 7 Divide by 128 (125 kHz)

6.17.5.20 DECODER
Address offset: 0x510
Configuration of the decoder

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW LOAD How a sequence is read from RAM and spread to the compare register
Common 0 1st half word (16-bit) used in all PWM channels 0..3
Grouped 1 1st half word (16-bit) used in channel 0..1; 2nd word in channel 2..3
Individual 2 1st half word (16-bit) in ch.0; 2nd in ch.1; ...; 4th in ch.3
WaveForm 3 1st half word (16-bit) in ch.0; 2nd in ch.1; ...; 4th in COUNTERTOP
B RW MODE Selects source for advancing the active sequence
RefreshCount 0 SEQ[n].REFRESH is used to determine loading internal compare registers
NextStep 1 NEXTSTEP task causes a new value to be loaded to internal compare
registers

6.17.5.21 LOOP
Address offset: 0x514
Number of playbacks of a loop

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW CNT Number of playbacks of pattern cycles
Disabled 0 Looping disabled (stop at the end of the sequence)

6.17.5.22 SEQ[0].PTR
Address offset: 0x520
Beginning address in RAM of this sequence

4413_417 v1.9 480

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PTR Beginning address in RAM of this sequence

Note: See the memory chapter for details about which memories
are available for EasyDMA.

6.17.5.23 SEQ[0].CNT
Address offset: 0x524
Number of values (duty cycles) in this sequence

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW CNT Number of values (duty cycles) in this sequence
Disabled 0 Sequence is disabled, and shall not be started as it is empty

6.17.5.24 SEQ[0].REFRESH
Address offset: 0x528
Number of additional PWM periods between samples loaded into compare register

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000001 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
ID R/W Field Value ID Value Description
A RW CNT Number of additional PWM periods between samples loaded into compare
register (load every REFRESH.CNT+1 PWM periods)
Continuous 0 Update every PWM period

6.17.5.25 SEQ[0].ENDDELAY
Address offset: 0x52C
Time added after the sequence

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW CNT Time added after the sequence in PWM periods

6.17.5.26 SEQ[1].PTR
Address offset: 0x540
Beginning address in RAM of this sequence

4413_417 v1.9 481

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PTR Beginning address in RAM of this sequence

Note: See the memory chapter for details about which memories
are available for EasyDMA.

6.17.5.27 SEQ[1].CNT
Address offset: 0x544
Number of values (duty cycles) in this sequence

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW CNT Number of values (duty cycles) in this sequence
Disabled 0 Sequence is disabled, and shall not be started as it is empty

6.17.5.28 SEQ[1].REFRESH
Address offset: 0x548
Number of additional PWM periods between samples loaded into compare register

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000001 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
ID R/W Field Value ID Value Description
A RW CNT Number of additional PWM periods between samples loaded into compare
register (load every REFRESH.CNT+1 PWM periods)
Continuous 0 Update every PWM period

6.17.5.29 SEQ[1].ENDDELAY
Address offset: 0x54C
Time added after the sequence

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW CNT Time added after the sequence in PWM periods

6.17.5.30 PSEL.OUT[0]
Address offset: 0x560
Output pin select for PWM channel 0

4413_417 v1.9 482

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.17.5.31 PSEL.OUT[1]
Address offset: 0x564
Output pin select for PWM channel 1

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.17.5.32 PSEL.OUT[2]
Address offset: 0x568
Output pin select for PWM channel 2

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A
Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.17.5.33 PSEL.OUT[3]
Address offset: 0x56C
Output pin select for PWM channel 3

4413_417 v1.9 483

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.18 QDEC — Quadrature decoder

The Quadrature decoder (QDEC) provides buffered decoding of quadrature-encoded sensor signals. It is
suitable for mechanical and optical sensors.
The sample period and accumulation are configurable to match application requirements. The QDEC
provides the following:
• Digital waveform decoding from off-chip quadrature encoder
• Sample accumulation eliminating hard real-time requirements to be enforced on application
• Optional input de-bounce filters.
• Optional LED output signal for optical encoders

ACCREAD ACCDBLREAD

ACC ACCDBL

+ +

SAMPLE

Quadrature decoder

IO router

On-chip
Off-chip Phase A Phase B LED

Mechanical to electrical

Mechanical
device

Quadrature Encoder

Figure 85: Quadrature decoder configuration

4413_417 v1.9 484

 Peripherals

6.18.1 Sampling and decoding

The QDEC decodes the output from an incremental motion encoder by sampling the QDEC phase input
pins (A and B).
The off-chip quadrature encoder is an incremental motion encoder outputting two waveforms, phase A
and phase B. The two output waveforms are always 90 degrees out of phase, meaning that one always
changes level before the other. The direction of movement is indicated by the waveform that changes level
first. Invalid transitions may occur, meaning the two waveforms simultaneously switch. This may occur if
the wheel rotates too fast relative to the sample rate set for the decoder.
The QDEC decodes the output from the off-chip encoder by sampling the QDEC phase input pins (A and B)
at a fixed rate as specified in the SAMPLEPER register.
If the SAMPLEPER value needs to be changed, the QDEC shall be stopped using the STOP task. SAMPLEPER
can be then changed upon receiving the STOPPED event, and QDEC can be restarted using the START task.
Failing to do so may result in unpredictable behavior.
It is good practice to only change registers LEDPOL, REPORTPER, DBFEN, and LEDPRE when the QDEC is
stopped.
When started, the decoder continuously samples the two input waveforms and decodes these by
comparing the current sample pair (n) with the previous sample pair (n-1).
The decoding of the sample pairs is described in the table below.

Previous Current SAMPLE ACC operation ACCDBL Description

sample pair(n samples register operation
- 1) pair(n)

A B A B
0 0 0 0 0 No change No change No movement
0 0 0 1 1 Increment No change Movement in positive direction
0 0 1 0 -1 Decrement No change Movement in negative direction
0 0 1 1 2 No change Increment Error: Double transition
0 1 0 0 -1 Decrement No change Movement in negative direction
0 1 0 1 0 No change No change No movement
0 1 1 0 2 No change Increment Error: Double transition
0 1 1 1 1 Increment No change Movement in positive direction
1 0 0 0 1 Increment No change Movement in positive direction
1 0 0 1 2 No change Increment Error: Double transition
1 0 1 0 0 No change No change No movement
1 0 1 1 -1 Decrement No change Movement in negative direction
1 1 0 0 2 No change Increment Error: Double transition
1 1 0 1 -1 Decrement No change Movement in negative direction
1 1 1 0 1 Increment No change Movement in positive direction
1 1 1 1 0 No change No change No movement

Table 32: Sampled value encoding

6.18.2 LED output

The LED output follows the sample period. The LED is switched on for a set period before sampling and
then switched off immediately after. The period the LED is switched on before sampling is given in the
LEDPRE register.
The LED output pin polarity is specified in the LEDPOL register.

4413_417 v1.9 485

 Peripherals

When using off-chip mechanical encoders not requiring an LED, the LED output can be disabled by writing
value 'Disconnected' to the CONNECT field of the PSEL.LED register. In this case, the QDEC will not acquire
access to a pin for the LED output.

6.18.3 Debounce filters

Each of the two-phase inputs have digital debounce filters.
When enabled through the DBFEN register, the filter inputs are sampled at a fixed 1 MHz frequency during
the entire sample period (which is specified in the SAMPLEPER register). The filters require all of the
samples within this sample period to equal before the input signal is accepted and transferred to the
output of the filter.
As a result, only input signal with a steady state longer than twice the period specified in SAMPLEPER are
guaranteed to pass through the filter. Any signal with a steady state shorter than SAMPLEPER will always
be suppressed by the filter. It is assumed that the frequency during the debounce period never exceeds
500 kHz (as required by the Nyquist theorem when using a 1 MHz sample frequency).
The LED will always be ON when the debounce filters are enabled, as the inputs in this case will be
sampled continuously.
When the debounce filters are enabled, displacements reported by the QDEC peripheral are delayed by
one SAMPLEPER period.

6.18.4 Accumulators
The quadrature decoder contains two accumulator registers, ACC and ACCDBL. These registers accumulate
valid motion sample values and the number of detected invalid samples (double transitions), respectively.
The ACC register accumulates all valid values (1/-1) written to the SAMPLE register. This can be useful for
preventing hard real-time requirements from being enforced on the application. When using the ACC
register, the application can fetch data when necessary instead of reading all SAMPLE register output. The
ACC register holds the relative movement of the external mechanical device from the previous clearing
of the ACC register. Sample values indicating a double transition (2) will not be accumulated in the ACC
register.
An ACCOF event is generated if the ACC receives a SAMPLE value that would cause the register to overflow
or underflow. Any SAMPLE value that would cause an ACC overflow or underflow will be discarded, but
any samples that do not cause the ACC to overflow or underflow will still be accepted.
The accumulator ACCDBL accumulates the number of detected double transitions since the previous
clearing of the ACCDBL register.
The ACC and ACCDBL registers can be cleared by the READCLRACC and subsequently read using the
ACCREAD and ACCDBLREAD registers.
The ACC register can be separately cleared by the RDCLRACC and subsequently read using the ACCREAD
registers.
The ACCDBL register can be separately cleared by the RDCLRDBL and subsequently read using the
ACCDBLREAD registers.
The REPORTPER register allows automated capture of multiple samples before sending an event. When
a non-null displacement is captured and accumulated, a REPORTRDY event is sent. When one or more
double-displacements are captured and accumulated, a DBLRDY event is sent. The REPORTPER field in this
register determines how many samples must be accumulated before the contents are evaluated and a
REPORTRDY or DBLRDY event is sent.
Using the RDCLRACC task (manually sent upon receiving the event, or using the DBLRDY_RDCLRACC
shortcut), ACCREAD can then be read.

4413_417 v1.9 486

 Peripherals

When a double transition has been captured and accumulated, a DBLRDY event is sent. Using the
RDCLRDBL task (manually sent upon receiving the event, or using the DBLRDY_RDCLRDBL shortcut),
ACCDBLREAD can then be read.

6.18.5 Output/input pins

The QDEC uses a three-pin interface to the off-chip quadrature encoder.
These pins are acquired when the QDEC is enabled in the ENABLE register. The pins acquired by the QDEC
cannot be written by the CPU, but they can still be read by the CPU.
The pin numbers used for the QDEC are selected using the PSEL.n registers.

6.18.6 Pin configuration

The Phase A, Phase B, and LED signals are mapped to physical pins according to the configuration specified
in the PSEL.A, PSEL.B, and PSEL.LED registers respectively.
If the CONNECT field value 'Disconnected' is specified in any of these registers, the associated signal will
not be connected to any physical pin. The PSEL.A, PSEL.B, and PSEL.LED registers and their configurations
are only used as long as the QDEC is enabled, and retained only as long as the device is in ON mode.
When the peripheral is disabled, the pins will behave as regular GPIOs, and use the configuration in their
respective OUT bit field and PIN_CNF[n] register.
To secure correct behavior in the QDEC, the pins used by the QDEC must be configured in the GPIO
peripheral as described in GPIO configuration before enabling peripheral on page 487 before enabling
the QDEC. This configuration must be retained in the GPIO for the selected I/Os as long as the QDEC is
enabled.
Only one peripheral can be assigned to drive a particular GPIO pin at a time. Failing to do so may result in
unpredictable behavior.

QDEC signal QDEC pin Direction Output value Comment

Phase A As specified in PSEL.A Input Not applicable
Phase B As specified in PSEL.B Input Not applicable
LED As specified in PSEL.LED Input Not applicable

Table 33: GPIO configuration before enabling peripheral

6.18.7 Registers
Instances

Instance Base address Description

QDEC 0x40012000 Quadrature decoder

Register overview

Register Offset Description

TASKS_START 0x000 Task starting the quadrature decoder
TASKS_STOP 0x004 Task stopping the quadrature decoder
TASKS_READCLRACC 0x008 Read and clear ACC and ACCDBL
TASKS_RDCLRACC 0x00C Read and clear ACC
TASKS_RDCLRDBL 0x010 Read and clear ACCDBL
EVENTS_SAMPLERDY 0x100 Event being generated for every new sample value written to the SAMPLE register

4413_417 v1.9 487

 Peripherals

Register Offset Description

EVENTS_REPORTRDY 0x104 Non-null report ready
EVENTS_ACCOF 0x108 ACC or ACCDBL register overflow
EVENTS_DBLRDY 0x10C Double displacement(s) detected
EVENTS_STOPPED 0x110 QDEC has been stopped
SHORTS 0x200 Shortcuts between local events and tasks
INTENSET 0x304 Enable interrupt
INTENCLR 0x308 Disable interrupt
ENABLE 0x500 Enable the quadrature decoder
LEDPOL 0x504 LED output pin polarity
SAMPLEPER 0x508 Sample period
SAMPLE 0x50C Motion sample value
REPORTPER 0x510 Number of samples to be taken before REPORTRDY and DBLRDY events can be generated
ACC 0x514 Register accumulating the valid transitions
ACCREAD 0x518 Snapshot of the ACC register, updated by the READCLRACC or RDCLRACC task
PSEL.LED 0x51C Pin select for LED signal
PSEL.A 0x520 Pin select for A signal
PSEL.B 0x524 Pin select for B signal
DBFEN 0x528 Enable input debounce filters
LEDPRE 0x540 Time period the LED is switched ON prior to sampling
ACCDBL 0x544 Register accumulating the number of detected double transitions
ACCDBLREAD 0x548 Snapshot of the ACCDBL, updated by the READCLRACC or RDCLRDBL task

6.18.7.1 TASKS_START
Address offset: 0x000
Task starting the quadrature decoder
When started, the SAMPLE register will be continuously updated at the rate given in the SAMPLEPER
register.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_START Task starting the quadrature decoder

When started, the SAMPLE register will be continuously updated at the rate
given in the SAMPLEPER register.
Trigger 1 Trigger task

6.18.7.2 TASKS_STOP
Address offset: 0x004
Task stopping the quadrature decoder

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STOP Task stopping the quadrature decoder
Trigger 1 Trigger task

4413_417 v1.9 488

 Peripherals

6.18.7.3 TASKS_READCLRACC
Address offset: 0x008
Read and clear ACC and ACCDBL
Task transferring the content of ACC to ACCREAD and the content of ACCDBL to ACCDBLREAD, and then
clearing the ACC and ACCDBL registers. These read-and-clear operations will be done atomically.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_READCLRACC Read and clear ACC and ACCDBL

Task transferring the content of ACC to ACCREAD and the content of ACCDBL
to ACCDBLREAD, and then clearing the ACC and ACCDBL registers. These
read-and-clear operations will be done atomically.
Trigger 1 Trigger task

6.18.7.4 TASKS_RDCLRACC
Address offset: 0x00C
Read and clear ACC
Task transferring the content of ACC to ACCREAD, and then clearing the ACC register. This read-and-clear
operation will be done atomically.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_RDCLRACC Read and clear ACC

Task transferring the content of ACC to ACCREAD, and then clearing the ACC
register. This read-and-clear operation will be done atomically.
Trigger 1 Trigger task

6.18.7.5 TASKS_RDCLRDBL
Address offset: 0x010
Read and clear ACCDBL
Task transferring the content of ACCDBL to ACCDBLREAD, and then clearing the ACCDBL register. This read-
and-clear operation will be done atomically.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_RDCLRDBL Read and clear ACCDBL

Task transferring the content of ACCDBL to ACCDBLREAD, and then clearing

the ACCDBL register. This read-and-clear operation will be done atomically.
Trigger 1 Trigger task

4413_417 v1.9 489

 Peripherals

6.18.7.6 EVENTS_SAMPLERDY
Address offset: 0x100
Event being generated for every new sample value written to the SAMPLE register

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_SAMPLERDY Event being generated for every new sample value written to the SAMPLE
register
NotGenerated 0 Event not generated
Generated 1 Event generated

6.18.7.7 EVENTS_REPORTRDY
Address offset: 0x104
Non-null report ready
Event generated when REPORTPER number of samples has been accumulated in the ACC register and the
content of the ACC register is not equal to 0. (Thus, this event is only generated if a motion is detected
since the previous clearing of the ACC register).

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_REPORTRDY Non-null report ready

Event generated when REPORTPER number of samples has been

accumulated in the ACC register and the content of the ACC register is not
equal to 0. (Thus, this event is only generated if a motion is detected since
the previous clearing of the ACC register).
NotGenerated 0 Event not generated
Generated 1 Event generated

6.18.7.8 EVENTS_ACCOF
Address offset: 0x108
ACC or ACCDBL register overflow

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_ACCOF ACC or ACCDBL register overflow
NotGenerated 0 Event not generated
Generated 1 Event generated

6.18.7.9 EVENTS_DBLRDY
Address offset: 0x10C
Double displacement(s) detected

4413_417 v1.9 490

 Peripherals

Event generated when REPORTPER number of samples has been accumulated and the content of the
ACCDBL register is not equal to 0. (Thus, this event is only generated if a double transition is detected
since the previous clearing of the ACCDBL register).

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_DBLRDY Double displacement(s) detected

Event generated when REPORTPER number of samples has been

accumulated and the content of the ACCDBL register is not equal to 0.
(Thus, this event is only generated if a double transition is detected since
the previous clearing of the ACCDBL register).
NotGenerated 0 Event not generated
Generated 1 Event generated

6.18.7.10 EVENTS_STOPPED
Address offset: 0x110
QDEC has been stopped

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_STOPPED QDEC has been stopped
NotGenerated 0 Event not generated
Generated 1 Event generated

6.18.7.11 SHORTS
Address offset: 0x200
Shortcuts between local events and tasks

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW REPORTRDY_READCLRACC Shortcut between event REPORTRDY and task READCLRACC
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
B RW SAMPLERDY_STOP Shortcut between event SAMPLERDY and task STOP
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
C RW REPORTRDY_RDCLRACC Shortcut between event REPORTRDY and task RDCLRACC
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
D RW REPORTRDY_STOP Shortcut between event REPORTRDY and task STOP
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
E RW DBLRDY_RDCLRDBL Shortcut between event DBLRDY and task RDCLRDBL
Disabled 0 Disable shortcut

4413_417 v1.9 491

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Enabled 1 Enable shortcut
F RW DBLRDY_STOP Shortcut between event DBLRDY and task STOP
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
G RW SAMPLERDY_READCLRACC Shortcut between event SAMPLERDY and task READCLRACC
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut

6.18.7.12 INTENSET
Address offset: 0x304
Enable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW SAMPLERDY Write '1' to enable interrupt for event SAMPLERDY
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW REPORTRDY Write '1' to enable interrupt for event REPORTRDY

Event generated when REPORTPER number of samples has been

accumulated in the ACC register and the content of the ACC register is not
equal to 0. (Thus, this event is only generated if a motion is detected since
the previous clearing of the ACC register).
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW ACCOF Write '1' to enable interrupt for event ACCOF
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
D RW DBLRDY Write '1' to enable interrupt for event DBLRDY

Event generated when REPORTPER number of samples has been

accumulated and the content of the ACCDBL register is not equal to 0.
(Thus, this event is only generated if a double transition is detected since
the previous clearing of the ACCDBL register).
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
E RW STOPPED Write '1' to enable interrupt for event STOPPED
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.18.7.13 INTENCLR
Address offset: 0x308

4413_417 v1.9 492

 Peripherals

Disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E D C B A
Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW SAMPLERDY Write '1' to disable interrupt for event SAMPLERDY
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW REPORTRDY Write '1' to disable interrupt for event REPORTRDY

Event generated when REPORTPER number of samples has been

accumulated in the ACC register and the content of the ACC register is not
equal to 0. (Thus, this event is only generated if a motion is detected since
the previous clearing of the ACC register).
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW ACCOF Write '1' to disable interrupt for event ACCOF
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
D RW DBLRDY Write '1' to disable interrupt for event DBLRDY

Event generated when REPORTPER number of samples has been

accumulated and the content of the ACCDBL register is not equal to 0.
(Thus, this event is only generated if a double transition is detected since
the previous clearing of the ACCDBL register).
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
E RW STOPPED Write '1' to disable interrupt for event STOPPED
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.18.7.14 ENABLE
Address offset: 0x500
Enable the quadrature decoder

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A- RW ENABLE Enable or disable the quadrature decoder

When enabled the decoder pins will be active. When disabled the
quadrature decoder pins are not active and can be used as GPIO .
Disabled 0 Disable
Enabled 1 Enable

4413_417 v1.9 493

 Peripherals

6.18.7.15 LEDPOL
Address offset: 0x504
LED output pin polarity

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW LEDPOL LED output pin polarity
ActiveLow 0 Led active on output pin low
ActiveHigh 1 Led active on output pin high

6.18.7.16 SAMPLEPER
Address offset: 0x508
Sample period

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW SAMPLEPER Sample period. The SAMPLE register will be updated for every new sample
128us 0 128 µs
256us 1 256 µs
512us 2 512 µs
1024us 3 1024 µs
2048us 4 2048 µs
4096us 5 4096 µs
8192us 6 8192 µs
16384us 7 16384 µs
32ms 8 32768 µs
65ms 9 65536 µs
131ms 10 131072 µs

6.18.7.17 SAMPLE
Address offset: 0x50C
Motion sample value

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R SAMPLE [-1..2] Last motion sample

The value is a 2's complement value, and the sign gives the direction of the
motion. The value '2' indicates a double transition.

6.18.7.18 REPORTPER
Address offset: 0x510

4413_417 v1.9 494

 Peripherals

Number of samples to be taken before REPORTRDY and DBLRDY events can be generated

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A
Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW REPORTPER Specifies the number of samples to be accumulated in the ACC register
before the REPORTRDY and DBLRDY events can be generated.

The report period in [µs] is given as: RPUS = SP * RP Where RPUS is the
report period in [µs/report], SP is the sample period in [µs/sample] specified
in SAMPLEPER, and RP is the report period in [samples/report] specified in
REPORTPER .
10Smpl 0 10 samples/report
40Smpl 1 40 samples/report
80Smpl 2 80 samples/report
120Smpl 3 120 samples/report
160Smpl 4 160 samples/report
200Smpl 5 200 samples/report
240Smpl 6 240 samples/report
280Smpl 7 280 samples/report
1Smpl 8 1 sample/report

6.18.7.19 ACC
Address offset: 0x514
Register accumulating the valid transitions

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R ACC [-1024..1023] Register accumulating all valid samples (not double transition) read from the
SAMPLE register.

Double transitions ( SAMPLE = 2 ) will not be accumulated in this register.

The value is a 32 bit 2's complement value. If a sample that would cause this
register to overflow or underflow is received, the sample will be ignored and
an overflow event ( ACCOF ) will be generated. The ACC register is cleared
by triggering the READCLRACC or the RDCLRACC task.

6.18.7.20 ACCREAD
Address offset: 0x518
Snapshot of the ACC register, updated by the READCLRACC or RDCLRACC task

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R ACCREAD [-1024..1023] Snapshot of the ACC register.

The ACCREAD register is updated when the READCLRACC or RDCLRACC task

is triggered.

4413_417 v1.9 495

 Peripherals

6.18.7.21 PSEL.LED
Address offset: 0x51C
Pin select for LED signal

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.18.7.22 PSEL.A
Address offset: 0x520
Pin select for A signal

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.18.7.23 PSEL.B
Address offset: 0x524
Pin select for B signal

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.18.7.24 DBFEN
Address offset: 0x528
Enable input debounce filters

4413_417 v1.9 496

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW DBFEN Enable input debounce filters
Disabled 0 Debounce input filters disabled
Enabled 1 Debounce input filters enabled

6.18.7.25 LEDPRE
Address offset: 0x540
Time period the LED is switched ON prior to sampling

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A

Reset 0x00000010 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0
ID R/W Field Value ID Value Description
A RW LEDPRE [1..511] Period in µs the LED is switched on prior to sampling

6.18.7.26 ACCDBL
Address offset: 0x544
Register accumulating the number of detected double transitions

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R ACCDBL [0..15] Register accumulating the number of detected double or illegal transitions.
( SAMPLE = 2 ).

When this register has reached its maximum value, the accumulation
of double/illegal transitions will stop. An overflow event (ACCOF) will
be generated if any double or illegal transitions are detected after the
maximum value was reached. This field is cleared by triggering the
READCLRACC or RDCLRDBL task.

6.18.7.27 ACCDBLREAD
Address offset: 0x548
Snapshot of the ACCDBL, updated by the READCLRACC or RDCLRDBL task

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R ACCDBLREAD [0..15] Snapshot of the ACCDBL register. This field is updated when the
READCLRACC or RDCLRDBL task is triggered.

4413_417 v1.9 497

 Peripherals

6.18.8 Electrical specification

6.18.8.1 QDEC Electrical Specification

Symbol Description Min. Typ. Max. Units

tSAMPLE Time between sampling signals from quadrature decoder 128 131072 µs
tLED Time from LED is turned on to signals are sampled 0 511 µs

6.19 QSPI — Quad serial peripheral interface

The QSPI peripheral provides support for communicating with an external flash memory device using SPI.
Listed here are the main features for the QSPI peripheral:
• Single/dual/quad SPI input/output
• 2–32 MHz configurable clock frequency
• Single-word read/write access from/to external flash
• EasyDMA for block read and write transfers
• Up to 16 MB/sec EasyDMA read rate
• Execute in place (XIP) for executing program directly from external flash
EraseStart
Activate
ReadStart
WriteStart

Deactivate

QSPI PSEL.SCK
PSEL.CSN
PSEL.IO0
PSEL.IO1
EasyDMA XIP PSEL.IO2
PSEL.IO3
Ready

Figure 86: Block diagram

6.19.1 Configuring peripheral

Before any data can be transferred to or from the external flash memory, the peripheral needs to be
configured.
1. Select input/output pins in PSEL.SCK on page 512, PSEL.CSN on page 512, PSEL.IO0 on page
513, PSEL.IO1 on page 513, PSEL.IO2 on page 513, and PSEL.IO3 on page 513. See Reference
circuitry on page 856 for the recommended pins.

4413_417 v1.9 498

 Peripherals

2. To ensure stable operation, set the GPIO drive strength to “high drive”. See the GPIO — General
purpose input/output on page 240 chapter for details on how to configure GPIO drive strength.
3. Configure the interface towards the external flash memory using IFCONFIG0 on page 514,
IFCONFIG1 on page 515, and ADDRCONF on page 516.
4. Enable the QSPI peripheral and acquire I/O pins using ENABLE on page 510.
5. Activate the external flash memory interface using the ACTIVATE task. The READY event will be
generated when the interface has been activated and the external flash memory is ready for access.

Important:
If the IFCONFIG0 on page 514 register is configured to use the quad mode, the external flash
device also needs to be set in the quad mode before any data transfers can take place.
This can be done by sending custom instructions to the external flash device, as described in
Sending custom instructions on page 500.

6.19.2 Write operation

A write operation to the external flash is configured using the WRITE.DST on page 511, WRITE.SRC on
page 511, and WRITE.CNT on page 511 registers and started using the WRITESTART task.
The READY event is generated when the transfer is complete.
The QSPI peripheral automatically takes care of splitting DMA transfers into page writes.

6.19.3 Read operation

A read operation from the external flash is configured using the READ.SRC on page 510, READ.DST on
page 510, and READ.CNT on page 511 registers and started using the READSTART task.
The READY event is generated when the transfer is complete.

6.19.4 Erase operation

Erase of pages/blocks of the external flash is configured using the ERASE.PTR on page 511 and
ERASE.LEN on page 512 registers and started using the ERASESTART task.
The READY event is generated when the erase operation has been started.
Note that in this case the READY event will not indicate that the erase operation of the flash has been
completed, but it only signals that the erase operation has been started. The actual status of the erase
operation can normally be read from the external flash using a custom instruction, see Sending custom
instructions on page 500.

6.19.5 Execute in place

Execute in place (XIP) allows the CPU to execute program code directly from the external flash.
After the external flash has been configured, the CPU can execute code from the external flash by
accessing the XIP memory region. See the figure below and Memory map on page 22 for details.
Note that the XIP memory region is read-only, writing to it will result in a bus error.
When accessing the XIP memory region, the start address of this XIP memory region will map to the
address XIPOFFSET on page 514 of the external flash.

4413_417 v1.9 499

 Peripherals

System Address Map External Flash

RAM

0x60000000

Peripheral

0x40000000

SRAM

0x20000000
XIP XIP
Code

0x00000000

XIPOFFSET

0x00000000

Figure 87: XIP memory map

6.19.6 Sending custom instructions

Custom instructions can be sent to the external flash using the CINSTRCONF on page 516, CINSTRDAT0
on page 517, and CINSTRDAT1 on page 517 registers. It is possible to send an instruction consisting of
a one-byte opcode and up to 8 bytes of additional data and to read its response.
A custom instruction is prepared by first writing the data to be sent to CINSTRDAT0 on page 517 and
CINSTRDAT1 on page 517 before writing the opcode and other configurations to the CINSTRCONF on
page 516 register.
The custom instruction is sent when the CINSTRCONF on page 516 register is written and it is always
sent on a single data line SPI interface.
The READY event will be generated when the custom instruction has been sent.
After a custom instruction has been sent, the CINSTRDAT0 on page 517 and CINSTRDAT1 on page 517
will contain the response bytes from the custom instruction.

Figure 88: Sending custom instruction

4413_417 v1.9 500

 Peripherals

6.19.6.1 Long frame mode

The LFEN and LFSTOP fields in the CINSTRCONF on page 516 control the operation of the custom
instruction long frame mode. The long frame mode is a mechanism that permits arbitrary byte length
custom instructions. While in long frame mode a long custom instruction sequence is split in multiple
writes to the CINSTRDAT0 on page 517 and CINSTRDAT1 on page 517 registers.
To enable the long frame mode every write to the CINSTRCONF on page 516 register must have
the LFEN field set to 1. The contents of the OPCODE field will be transmitted after the first write to
CINSTRCONF on page 516 and will be omitted in every subsequent write to this register. For subsequent
writes the number of data bytes as specified in the LENGTH field are transferred (that is the value of
LENGTH - 1 data bytes). The values of the LIO2 and LIO3 fields are set in the first write to CINSTRCONF on
page 516 and will apply for the entire custom instruction transmission until the long frame is finalized.
To finalize a long frame transmission, the LFSTOP field in CINSTRCONF on page 516 must be set to 1 in
the last write to this register.

6.19.7 Deep power-down mode

The external flash memory can be put in deep power-down mode (DPM) to minimize its current
consumption when there is no need to access the memory.
DPM is enabled in the IFCONFIG0 on page 514 register and configured in the DPMDUR on page 515
register. The DPM status of the external memory can be read in the STATUS on page 515 register. The
DPMDUR register has to be configured according to the external flash specification to get the information
in the STATUS register and the timing of the READY event correct.
Entering/exiting DPM is controlled using the IFCONFIG1 on page 515 register.

6.19.8 Instruction set

The table below shows the instruction set being used by the QSPI peripheral when communicating with an
external flash device.

Instruction Opcode Description

WREN 0x06 Write enable
RDSR 0x05 Read status register
WRSR 0x01 Write status register
FASTREAD 0x0B Read bytes at higher speed
READ2O 0x3B Dual-read output
READ2IO 0xBB Dual-read input/output
READ4O 0x6B Quad-read output
READ4IO 0xEB Quad-read input/output
PP 0x02 Page program
PP2O 0xA2 Dual-page program output
PP4O 0x32 Quad-page program output
PP4IO 0x38 Quad-page program input/output
SE 0x20 Sector erase
BE 0xD8 Block erase
CE 0xC7 Chip erase
DP 0xB9 Enter deep power-down mode
DPE 0xAB Exit deep power-down mode
EN4B Specified in the ADDRCONF on page 516 register Enable 32 bit address mode

Table 34: Instruction set

6.19.9 Interface description

4413_417 v1.9 501

 Peripherals

Figure 89: 24-bit FASTREAD, SPIMODE = MODE0

Figure 90: 24-bit READ2O (dual-read output), SPIMODE = MODE0

Figure 91: 24-bit READ2IO (dual read input/output), SPIMODE = MODE0

Figure 92: 24-bit READ4O (quad-read output), SPIMODE = MODE0

4413_417 v1.9 502

 Peripherals

Figure 93: 24-bit READ4IO (quad-read input/output), SPIMODE = MODE0

Figure 94: 24-bit PP (page program), SPIMODE = MODE0

Figure 95: 24-bit PP2O (dual-page program output), SPIMODE = MODE0

Figure 96: 24-bit PP4O (quad page program output), SPIMODE = MODE0

4413_417 v1.9 503

 Peripherals

Figure 97: 24-bit PP4IO (quad page program input/output), SPIMODE = MODE0

Figure 98: 32-bit FASTREAD, SPIMODE = MODE0

Figure 99: 32-bit READ2O (dual-read output), SPIMODE = MODE0

Figure 100: 32-bit READ2IO (dual read input/output), SPIMODE = MODE0

4413_417 v1.9 504

 Peripherals

Figure 101: 32-bit READ4O (quad-read output), SPIMODE = MODE0

Figure 102: 32-bit READ4IO (quad-read input/output), SPIMODE = MODE0

Figure 103: 32-bit PP (page program), SPIMODE = MODE0

Figure 104: 32-bit PP2O (dual-page program output), SPIMODE = MODE0

4413_417 v1.9 505

 Peripherals

Figure 105: 32-bit PP4O (quad-page program output), SPIMODE = MODE0

Figure 106: 32-bit PP4IO (quad page program input/output), SPIMODE = MODE0

6.19.10 Registers
Instances

Instance Base address Description

QSPI 0x40029000 External memory interface

Register overview

Register Offset Description

TASKS_ACTIVATE 0x000 Activate QSPI interface
TASKS_READSTART 0x004 Start transfer from external flash memory to internal RAM
TASKS_WRITESTART 0x008 Start transfer from internal RAM to external flash memory
TASKS_ERASESTART 0x00C Start external flash memory erase operation
TASKS_DEACTIVATE 0x010 Deactivate QSPI interface
EVENTS_READY 0x100 QSPI peripheral is ready. This event will be generated as a response to any QSPI task.
INTEN 0x300 Enable or disable interrupt
INTENSET 0x304 Enable interrupt
INTENCLR 0x308 Disable interrupt
ENABLE 0x500 Enable QSPI peripheral and acquire the pins selected in PSELn registers
READ.SRC 0x504 Flash memory source address
READ.DST 0x508 RAM destination address
READ.CNT 0x50C Read transfer length
WRITE.DST 0x510 Flash destination address
WRITE.SRC 0x514 RAM source address
WRITE.CNT 0x518 Write transfer length
ERASE.PTR 0x51C Start address of flash block to be erased

4413_417 v1.9 506

 Peripherals

Register Offset Description

ERASE.LEN 0x520 Size of block to be erased.
PSEL.SCK 0x524 Pin select for serial clock SCK
PSEL.CSN 0x528 Pin select for chip select signal CSN.
PSEL.IO0 0x530 Pin select for serial data MOSI/IO0.
PSEL.IO1 0x534 Pin select for serial data MISO/IO1.
PSEL.IO2 0x538 Pin select for serial data IO2.
PSEL.IO3 0x53C Pin select for serial data IO3.
XIPOFFSET 0x540 Address offset into the external memory for Execute in Place operation.
IFCONFIG0 0x544 Interface configuration.
IFCONFIG1 0x600 Interface configuration.
STATUS 0x604 Status register.
DPMDUR 0x614 Set the duration required to enter/exit deep power-down mode (DPM).
ADDRCONF 0x624 Extended address configuration.
CINSTRCONF 0x634 Custom instruction configuration register.
CINSTRDAT0 0x638 Custom instruction data register 0.
CINSTRDAT1 0x63C Custom instruction data register 1.
IFTIMING 0x640 SPI interface timing.

6.19.10.1 TASKS_ACTIVATE
Address offset: 0x000
Activate QSPI interface
Triggering this task activates the external flash memory interface and initiates communication with the
external memory. The READY event is generated when the activation has been completed.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_ACTIVATE Activate QSPI interface

Triggering this task activates the external flash memory interface and
initiates communication with the external memory. The READY event is
generated when the activation has been completed.
Trigger 1 Trigger task

6.19.10.2 TASKS_READSTART
Address offset: 0x004
Start transfer from external flash memory to internal RAM
Start transfer from external flash memory to internal RAM. The READY event will be generated when
transfer is complete.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_READSTART Start transfer from external flash memory to internal RAM

Start transfer from external flash memory to internal RAM. The READY event
will be generated when transfer is complete.
Trigger 1 Trigger task

4413_417 v1.9 507

 Peripherals

6.19.10.3 TASKS_WRITESTART
Address offset: 0x008
Start transfer from internal RAM to external flash memory
Start transfer from internal RAM to external flash memory. The READY event will be generated when
transfer is complete.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_WRITESTART Start transfer from internal RAM to external flash memory

Start transfer from internal RAM to external flash memory. The READY event
will be generated when transfer is complete.
Trigger 1 Trigger task

6.19.10.4 TASKS_ERASESTART
Address offset: 0x00C
Start external flash memory erase operation
Start external flash memory erase operation. The READY event will be generated when the erase
operation has been started. Note, generation of the READY event does not imply that the erase operation
is completed.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_ERASESTART Start external flash memory erase operation

Start external flash memory erase operation. The READY event will be
generated when the erase operation has been started. Note, generation of
the READY event does not imply that the erase operation is completed.
Trigger 1 Trigger task

6.19.10.5 TASKS_DEACTIVATE
Address offset: 0x010
Deactivate QSPI interface
Deactivate QSPI interface. This task might be needed to optimize current consumption in case there are
any added current consumption when QSPI interface is activated, but idle.

4413_417 v1.9 508

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_DEACTIVATE Deactivate QSPI interface

Deactivate QSPI interface. This task might be needed to optimize current

consumption in case there are any added current consumption when QSPI
interface is activated, but idle.
Trigger 1 Trigger task

6.19.10.6 EVENTS_READY
Address offset: 0x100
QSPI peripheral is ready. This event will be generated as a response to any QSPI task.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_READY QSPI peripheral is ready. This event will be generated as a response to any
QSPI task.
NotGenerated 0 Event not generated
Generated 1 Event generated

6.19.10.7 INTEN
Address offset: 0x300
Enable or disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW READY Enable or disable interrupt for event READY
Disabled 0 Disable
Enabled 1 Enable

6.19.10.8 INTENSET
Address offset: 0x304
Enable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW READY Write '1' to enable interrupt for event READY
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

4413_417 v1.9 509

 Peripherals

6.19.10.9 INTENCLR
Address offset: 0x308
Disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW READY Write '1' to disable interrupt for event READY
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.19.10.10 ENABLE
Address offset: 0x500
Enable QSPI peripheral and acquire the pins selected in PSELn registers

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW ENABLE Enable or disable QSPI
Disabled 0 Disable QSPI
Enabled 1 Enable QSPI

6.19.10.11 READ.SRC
Address offset: 0x504
Flash memory source address

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW SRC Word-aligned flash memory source address.

6.19.10.12 READ.DST
Address offset: 0x508
RAM destination address

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW DST Word-aligned RAM destination address.

4413_417 v1.9 510

 Peripherals

6.19.10.13 READ.CNT
Address offset: 0x50C
Read transfer length

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW CNT [1..0x3FFFF] Read transfer length in number of bytes. The length must be a multiple of 4
bytes.

6.19.10.14 WRITE.DST
Address offset: 0x510
Flash destination address

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW DST Word-aligned flash destination address.

6.19.10.15 WRITE.SRC
Address offset: 0x514
RAM source address

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW SRC Word-aligned RAM source address.

6.19.10.16 WRITE.CNT
Address offset: 0x518
Write transfer length

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW CNT [1..0x3FFFF] Write transfer length in number of bytes. The length must be a multiple of 4
bytes.

6.19.10.17 ERASE.PTR
Address offset: 0x51C
Start address of flash block to be erased

4413_417 v1.9 511

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PTR Word-aligned start address of block to be erased.

6.19.10.18 ERASE.LEN
Address offset: 0x520
Size of block to be erased.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW LEN LEN
4KB 0 Erase 4 kB block (flash command 0x20)
64KB 1 Erase 64 kB block (flash command 0xD8)
All 2 Erase all (flash command 0xC7)

6.19.10.19 PSEL.SCK
Address offset: 0x524
Pin select for serial clock SCK

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.19.10.20 PSEL.CSN
Address offset: 0x528
Pin select for chip select signal CSN.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

4413_417 v1.9 512

 Peripherals

6.19.10.21 PSEL.IO0
Address offset: 0x530
Pin select for serial data MOSI/IO0.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.19.10.22 PSEL.IO1
Address offset: 0x534
Pin select for serial data MISO/IO1.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.19.10.23 PSEL.IO2
Address offset: 0x538
Pin select for serial data IO2.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.19.10.24 PSEL.IO3
Address offset: 0x53C
Pin select for serial data IO3.

4413_417 v1.9 513

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.19.10.25 XIPOFFSET
Address offset: 0x540
Address offset into the external memory for Execute in Place operation.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW XIPOFFSET Address offset into the external memory for Execute in Place operation.
Value must be a multiple of 4.

6.19.10.26 IFCONFIG0
Address offset: 0x544
Interface configuration.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E D C B B B A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW READOC Configure number of data lines and opcode used for reading.
FASTREAD 0 Single data line SPI. FAST_READ (opcode 0x0B).
READ2O 1 Dual data line SPI. READ2O (opcode 0x3B).
READ2IO 2 Dual data line SPI. READ2IO (opcode 0xBB).
READ4O 3 Quad data line SPI. READ4O (opcode 0x6B).
READ4IO 4 Quad data line SPI. READ4IO (opcode 0xEB).
B RW WRITEOC Configure number of data lines and opcode used for writing.
PP 0 Single data line SPI. PP (opcode 0x02).
PP2O 1 Dual data line SPI. PP2O (opcode 0xA2).
PP4O 2 Quad data line SPI. PP4O (opcode 0x32).
PP4IO 3 Quad data line SPI. PP4IO (opcode 0x38).
C RW ADDRMODE Addressing mode.
24BIT 0 24-bit addressing.
32BIT 1 32-bit addressing.
D RW DPMENABLE Enable deep power-down mode (DPM) feature.
Disable 0 Disable DPM feature.
Enable 1 Enable DPM feature.
E RW PPSIZE Page size for commands PP, PP2O, PP4O and PP4IO.
256Bytes 0 256 bytes.
512Bytes 1 512 bytes.

4413_417 v1.9 514

 Peripherals

6.19.10.27 IFCONFIG1
Address offset: 0x600
Interface configuration.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID D D D D C B A A A A A A A A

Reset 0x00040480 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 1 0 0 1 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW SCKDELAY [0..255] Minimum amount of time that the CSN pin must stay high before it can go
low again. Value is specified in number of 16 MHz periods (62.5 ns).
B RW DPMEN Enter/exit deep power-down mode (DPM) for external flash memory.
Exit 0 Exit DPM.
Enter 1 Enter DPM.
C RW SPIMODE Select SPI mode.
MODE0 0 Mode 0: Data are captured on the clock rising edge and data is output on a
falling edge. Base level of clock is 0 (CPOL=0, CPHA=0).
MODE3 1 Mode 3: Data are captured on the clock falling edge and data is output on a
rising edge. Base level of clock is 1 (CPOL=1, CPHA=1).
D RW SCKFREQ [0..15] SCK frequency is given as 32 MHz / (SCKFREQ + 1).

6.19.10.28 STATUS
Address offset: 0x604
Status register.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C C C C C C C C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R DPM Deep power-down mode (DPM) status of external flash.
Disabled 0 External flash is not in DPM.
Enabled 1 External flash is in DPM.
B R READY Ready status.
READY 1 QSPI peripheral is ready. It is allowed to trigger new tasks, writing custom
instructions or enter/exit DPM.
BUSY 0 QSPI peripheral is busy. It is not allowed to trigger any new tasks, writing
custom instructions or enter/exit DPM.
C R SREG Value of external flash device Status Register. When the external flash has
two bytes status register this field includes the value of the low byte.

6.19.10.29 DPMDUR
Address offset: 0x614
Set the duration required to enter/exit deep power-down mode (DPM).

4413_417 v1.9 515

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B B B B B B B B B B B B B B B B A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW ENTER [0..0xFFFF] Duration needed by external flash to enter DPM. Duration is given as ENTER
* 256 * 62.5 ns.
B RW EXIT [0..0xFFFF] Duration needed by external flash to exit DPM. Duration is given as EXIT *
256 * 62.5 ns.

6.19.10.30 ADDRCONF
Address offset: 0x624
Extended address configuration.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID F E D D C C C C C C C C B B B B B B B B A A A A A A A A

Reset 0x000000B7 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 1 0 1 1 1
ID R/W Field Value ID Value Description
A RW OPCODE [0xFF..0] Opcode that enters the 32-bit addressing mode.
B RW BYTE0 [0xFF..0] Byte 0 following opcode.
C RW BYTE1 [0xFF..0] Byte 1 following byte 0.
D RW MODE Extended addressing mode.
NoInstr 0 Do not send any instruction.
Opcode 1 Send opcode.
OpByte0 2 Send opcode, byte0.
All 3 Send opcode, byte0, byte1.
E RW WIPWAIT Wait for write complete before sending command.
Disable 0 No wait.
Enable 1 Wait.
F RW WREN Send WREN (write enable opcode 0x06) before instruction.
Disable 0 Do not send WREN.
Enable 1 Send WREN.

6.19.10.31 CINSTRCONF
Address offset: 0x634
Custom instruction configuration register.
A new custom instruction is sent every time this register is written. The READY event will be generated
when the custom instruction has been sent.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID H G F E D C B B B B A A A A A A A A

Reset 0x00002000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW OPCODE [0..255] Opcode of Custom instruction.
B RW LENGTH Length of custom instruction in number of bytes.
1B 1 Send opcode only.
2B 2 Send opcode, CINSTRDAT0.BYTE0.
3B 3 Send opcode, CINSTRDAT0.BYTE0 -> CINSTRDAT0.BYTE1.
4B 4 Send opcode, CINSTRDAT0.BYTE0 -> CINSTRDAT0.BYTE2.
5B 5 Send opcode, CINSTRDAT0.BYTE0 -> CINSTRDAT0.BYTE3.
6B 6 Send opcode, CINSTRDAT0.BYTE0 -> CINSTRDAT1.BYTE4.

4413_417 v1.9 516

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID H G F E D C B B B B A A A A A A A A

Reset 0x00002000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
7B 7 Send opcode, CINSTRDAT0.BYTE0 -> CINSTRDAT1.BYTE5.
8B 8 Send opcode, CINSTRDAT0.BYTE0 -> CINSTRDAT1.BYTE6.
9B 9 Send opcode, CINSTRDAT0.BYTE0 -> CINSTRDAT1.BYTE7.
C RW LIO2 [0..1] Level of the IO2 pin (if connected) during transmission of custom
instruction.
D RW LIO3 [0..1] Level of the IO3 pin (if connected) during transmission of custom
instruction.
E RW WIPWAIT Wait for write complete before sending command.
Disable 0 No wait.
Enable 1 Wait.
F RW WREN Send WREN (write enable opcode 0x06) before instruction.
Disable 0 Do not send WREN.
Enable 1 Send WREN.
G RW LFEN Enable long frame mode. When enabled, a custom instruction transaction
has to be ended by writing the LFSTOP field.
Disable 0 Long frame mode disabled
Enable 1 Long frame mode enabled
H RW LFSTOP Stop (finalize) long frame transaction
Stop 1 Stop

6.19.10.32 CINSTRDAT0
Address offset: 0x638
Custom instruction data register 0.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID D D D D D D D D C C C C C C C C B B B B B B B B A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW BYTE0 [0..0xFF] Data byte 0
B RW BYTE1 [0..0xFF] Data byte 1
C RW BYTE2 [0..0xFF] Data byte 2
D RW BYTE3 [0..0xFF] Data byte 3

6.19.10.33 CINSTRDAT1
Address offset: 0x63C
Custom instruction data register 1.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID D D D D D D D D C C C C C C C C B B B B B B B B A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW BYTE4 [0..0xFF] Data byte 4
B RW BYTE5 [0..0xFF] Data byte 5
C RW BYTE6 [0..0xFF] Data byte 6
D RW BYTE7 [0..0xFF] Data byte 7

4413_417 v1.9 517

 Peripherals

6.19.10.34 IFTIMING
Address offset: 0x640
SPI interface timing.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A

Reset 0x00000200 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW RXDELAY [7..0] Timing related to sampling of the input serial data. The value of RXDELAY
specifies the number of 64 MHz cycles (15.625 ns) delay from the the rising
edge of the SPI Clock (SCK) until the input serial data is sampled. As en
example, if set to 0 the input serial data is sampled on the rising edge of
SCK.

6.19.11 Electrical specification

6.19.11.1 Timing specification

Symbol Description Min. Typ. Max. Units

FQSPI,CLK SCK frequency 32 MHz
DCQSPI,CLK SCK duty cycle %
FQSPI,XIP,16 XIP fetch frequency for 16 bit instructions 8 MHz
FQSPI,XIP,32 XIP fetch frequency for 32 bit instructions 4 MHz

6.20 RADIO — 2.4 GHz radio

The 2.4 GHz radio transceiver is compatible with multiple radio standards such as 1 Mbps, 2 Mbps and
long range Bluetooth low energy. IEEE 802.15.4 250 kbps mode is fully supported as well as Nordic's
proprietary 1 Mbps and 2 Mbps modes of operation.
Listed here are main features for the RADIO:
• Multidomain 2.4 GHz radio transceiver:
• 1 Mbps, 2 Mbps and long range (125 kbps and 500 kbps mode) Bluetooth low energy modes
• 250 kbps IEEE 802.15.4 mode
• 1 Mbps and 2 Mbps Nordic proprietary modes
• Best in class link budget and low power operation
• Efficient data interface with EasyDMA support
• Automatic address filtering and pattern matching
EasyDMA in combination with an automated packet assembler and packet disassembler, and an
automated CRC generator and CRC checker, make it very easy to configure and use the RADIO. See RADIO
block diagram on page 519 for details.

4413_417 v1.9 518

 Peripherals

RAM RADIO

PACKETPTR Device Packet synch RSSI

Address
address
match
match

S0 2.4 GHz
CRC Dewhitening
Packet receiver
L
disassembler
S1

EasyDMA
Payload
IFS
Bit counter
control unit

S0 ANT1

L Packet
assembler 2.4 GHz
S1 CRC Whitening
transmitter

Payload MAXLEN

Figure 107: RADIO block diagram

The RADIO includes a device address match unit and an interframe spacing control unit that can be utilized
to simplify address whitelisting and interframe spacing respectively in Bluetooth low energy and similar
applications.
The RADIO also includes a received signal strength indicator (RSSI) and a bit counter. The bit counter
generates events when a preconfigured number of bits have been sent or received by the RADIO.

6.20.1 Packet configuration

A radio packet contains the following fields: PREAMBLE, ADDRESS, S0, LENGTH, S1, PAYLOAD and CRC.
The content of a RADIO packet is illustrated in On air packet layout on page 519. The RADIO sends the
different fields in the packet in the order they are illustrated below, from left to right:
TERM
MSBit
LSBit

LSBit

LSBit

LSBit
PREAMBLE BASE PREFIX CI TERM1 S0 LENGTH S1 PAYLOAD CRC
2
LSByte LSByte MSByte
ADDRESS

Figure 108: On air packet layout

Not shown in the figure is the static payload add-on (the length of which is defined in STATLEN, and which
is 0 bytes long in a standard BLE packet). The static payload add-on is sent between PAYLOAD and CRC
fields. The radio sends the different fields in the packet in the order they are illustrated above, from left to
right. The preamble will be sent with least significant bit first on air.
Not shown in the figure above is the static payload add-on (the length of which is defined in
PCNF1.STATLEN, and which is 0 bytes long in a standard BLE packet). The static payload add-on is sent
between the PAYLOAD and CRC fields.
PREAMBLE is sent with least significant bit first on-air. The size of the PREAMBLE depends on the mode
selected in the MODE register:
• The PREAMBLE is one byte for MODE = Ble_1Mbit as well as all Nordic proprietary operating modes
(MODE = Nrf_1Mbit and MODE = Nrf_2Mbit), and the PLEN field in the PCNF0 register has to be
set accordingly. If the first bit of the ADDRESS is 0 the preamble will be set to 0xAA otherwise the
PREAMBLE will be set to 0x55.
• For MODE = Ble_2Mbit the PREAMBLE has to be set to 2 byte long through the PLEN field in the
PCNF0 register. If the first bit of the ADDRESS is 0 the preamble will be set to 0xAAAA otherwise the
PREAMBLE will be set to 0x5555.
• For MODE = Ble_LR125Kbit and MODE = Ble_LR500Kbit the PREAMBLE is 10 repetitions of 0x3C.

4413_417 v1.9 519

 Peripherals

• For MODE = Ieee802154_250Kbit the PREAMBLE is 4 bytes long and set to all zeros.
Radio packets are stored in memory inside instances of a radio packet data structure as illustrated in In-
RAM representation of radio packet - S0, LENGTH and S1 are optional on page 520. The PREAMBLE,
ADDRESS, CI, TERM1, TERM2 and CRC fields are omitted in this data structure.

S0 LENGTH S1 PAYLOAD

0 LSByte n

Figure 109: In-RAM representation of radio packet - S0, LENGTH and S1 are optional

The byte ordering on air is always least significant byte first for the ADDRESS and PAYLOAD fields and
most significant byte first for the CRC field. The ADDRESS fields are always transmitted and received least
significant bit first on air. The CRC field is always transmitted and received most significant bit first. The bit-
endian, i.e. the order in which the bits are sent and received, of the S0, LENGTH, S1 and PAYLOAD fields
can be configured via the ENDIAN in PCNF1.
The sizes of the S0, LENGTH and S1 fields can be individually configured via S0LEN, LFLEN and S1LEN in
PCNF0 respectively. If any of these fields are configured to be less than 8 bits long, the least significant bits
of the fields are used.
If S0, LENGTH or S1 are specified with zero length their fields will be omitted in memory, otherwise each
field will be represented as a separate byte, regardless of the number of bits in their on air counterpart.
Independent of the configuration of MAXLEN, the combined length of S0, LENGTH, S1 and PAYLOAD
cannot exceed 258 bytes.

6.20.2 Address configuration

The on air radio ADDRESS field is composed of two parts, the base address field and the address prefix
field.
The size of the base address field is configurable via BALEN in PCNF1. The base address is truncated from
the least significant byte if the BALEN is less than 4. See Definition of logical addresses on page 520.

Logical address Base address Prefix byte

0 BASE0 PREFIX0.AP0
1 BASE1 PREFIX0.AP1
2 BASE1 PREFIX0.AP2
3 BASE1 PREFIX0.AP3
4 BASE1 PREFIX1.AP4
5 BASE1 PREFIX1.AP5
6 BASE1 PREFIX1.AP6
7 BASE1 PREFIX1.AP7

Table 35: Definition of logical addresses

The on air addresses are defined in the BASEn and PREFIXn registers, and it is only when writing these
registers the user will have to relate to actual on air addresses. For other radio address registers such as
the TXADDRESS, RXADDRESSES and RXMATCH registers, logical radio addresses ranging from 0 to 7 are
being used. The relationship between the on air radio addresses and the logical addresses is described in
Definition of logical addresses on page 520.

4413_417 v1.9 520

 Peripherals

6.20.3 Data whitening

The RADIO is able to do packet whitening and de-whitening.
See WHITEEN in PCNF1 register for how to enable whitening. When enabled, whitening and de-whitening
will be handled by the RADIO automatically as packets are sent and received.
The whitening word is generated using polynomial g(D) = D7+ D4 + 1, which then is XORed with the data
packet that is to be whitened, or de-whitened. See the figure below.

D0 D4 D7 Data out

+ +
Position 0 1 2 3 4 5 6
Data in

Figure 110: Data whitening and de-whitening

Whitening and de-whitening will be performed over the whole packet (except for the preamble and the
address field).
The linear feedback shift register, illustrated in Data whitening and de-whitening on page 521 can be
initialised via the DATAWHITEIV register.

6.20.4 CRC
The CRC generator in the RADIO calculates the CRC over the whole packet excluding the preamble. If
desirable, the address field can be excluded from the CRC calculation as well
See CRCCNF register for more information.
The CRC polynomial is configurable as illustrated in CRC generation of an n bit CRC on page 521 where
bit 0 in the CRCPOLY register corresponds to X0 and bit 1 corresponds to X1 etc. See CRCPOLY for more
information.

Xn Xn-1 X2 X1 X0
Packet
(Clocked in serially)
+ + + + +
bn b0

Figure 111: CRC generation of an n bit CRC

As illustrated in CRC generation of an n bit CRC on page 521, the CRC is calculated by feeding the
packet serially through the CRC generator. Before the packet is clocked through the CRC generator, the
CRC generator's latches b0 through bn will be initialized with a predefined value specified in the CRCINIT
register. When the whole packet is clocked through the CRC generator, latches b0 through bn will hold
the resulting CRC. This value will be used by the RADIO during both transmission and reception but it is
not available to be read by the CPU at any time. A received CRC can however be read by the CPU via the
RXCRC register independent of whether or not it has passed the CRC check.
The length (n) of the CRC is configurable, see CRCCNF for more information.

4413_417 v1.9 521

 Peripherals

After the whole packet including the CRC has been received, the RADIO will generate a CRCOK event if no
CRC errors were detected, or alternatively generate a CRCERROR event if CRC errors were detected.
The status of the CRC check can be read from the CRCSTATUS register after a packet has been received.

6.20.5 Radio states

Tasks and events are used to control the operating state of the RADIO.
The RADIO can enter the states described the table below.

State Description
DISABLED No operations are going on inside the radio and the power consumption is at a minimum
RXRU The radio is ramping up and preparing for reception
RXIDLE The radio is ready for reception to start
RX Reception has been started and the addresses enabled in the RXADDRESSES register are being monitored
TXRU The radio is ramping up and preparing for transmission
TXIDLE The radio is ready for transmission to start
TX The radio is transmitting a packet
RXDISABLE The radio is disabling the receiver
TXDISABLE The radio is disabling the transmitter

Table 36: RADIO state diagram

An overview state diagram for the RADIO is illustrated in Radio states on page 522.

Note: The END to START shortcut should not be used with Ble_LR125Kbit, Ble_LR500Kbit and
Ieee802154_250Kbit modes. Rather the PHYEND to START shortcut.

DISABLE
Address sent / ADDRESS

START

TXDISABLE TXRU TXIDLE TX

Ramp-up
complete STOP
/ READY
/ DISABLED
TXEN Packet sent / END Payload sent [payload length >=0]
/ PAYLOAD
Last bit sent / PHYEND
DISABLED

RXEN Address received [Address match]

Packet received / END
/ DISABLED / ADDRESS
Ramp-up
complete START
/ READY
RXDISABLE RXRU RXIDLE RX

STOP

Payload received [payload length >=0]

DISABLE
/ PAYLOAD

Figure 112: Radio states

This figure shows how the tasks and events relate to the RADIO's operation. The RADIO does not prevent
a task from being triggered from the wrong state. If a task is triggered from the wrong state, for example if
the RXEN task is triggered from the RXDISABLE state, this may lead to incorrect behaviour. As illustrated in
Radio states on page 522, the PAYLOAD event is always generated even if the payload is zero.

6.20.6 Transmit sequence

Before the RADIO is able to transmit a packet, it must first ramp-up in TX mode.

4413_417 v1.9 522

 Peripherals

See TXRU in Radio states on page 522 and Transmit sequence on page 523. A TXRU ramp-up
sequence is initiated when the TXEN task is triggered. After the radio has successfully ramped up it will
generate the READY event indicating that a packet transmission can be initiate. A packet transmission is
initiated by triggering the START task. As illustrated in Radio states on page 522 the START task can first
be triggered after the RADIO has entered into the TXIDLE state.
State

TXRU TXIDLE TX TXIDLE TXDISABLE

Transmitter

(carrier) P A S0 L S1 PAYLOAD CRC (carrier)

DISABLED
READY

ADDRESS

PAYLOAD

END
Lifeline

1 2 3

DISABLE
START
TXEN

Figure 113: Transmit sequence

Transmit sequence on page 523 illustrates a single packet transmission where the CPU manually triggers
the different tasks needed to control the flow of the RADIO, i.e. no shortcuts are used. If shortcuts are
not used, a certain amount of delay caused by CPU execution is expected between READY and START, and
between END and DISABLE. As illustrated in Transmit sequence on page 523 the RADIO will by default
transmit '1's between READY and START, and between END and DISABLED. What is transmitted can be
programmed through the DTX field in the MODECNF0 register.
A slightly modified version of the transmit sequence from Transmit sequence on page 523 is illustrated
in Transmit sequence using shortcuts to avoid delays on page 523 where the RADIO is configured to
use shortcuts between READY and START, and between END and DISABLE, which means that no delay is
introduced.
State

TXRU TX TXDISABLE
Transmitter

P A S0 L S1 PAYLOAD CRC (carrier)

DISABLED
ADDRESS

PAYLOAD
READY

END
Lifeline

1 2
DISABLE
START
TXEN

Figure 114: Transmit sequence using shortcuts to avoid delays

The RADIO is able to send multiple packets one after the other without having to disable and re-enable
the RADIO between packets, this is illustrated in Transmission of multiple packets on page 524.

4413_417 v1.9 523

 Peripherals

State
TXRU TX TXIDLE TX TXDISABLE

Transmitter
P A S0 L S1 PAYLOAD CRC (carrier) P A S0 L S1 PAYLOAD CRC (carrier)

DISABLED
ADDRESS

ADDRESS
PAYLOAD

PAYLOAD
END
READY

END
Lifeline

1 2 3

DISABLE
START

START
TXEN

Figure 115: Transmission of multiple packets

6.20.7 Receive sequence

Before the RADIO is able to receive a packet, it must first ramp up in RX mode
See RXRU in Radio states on page 522 and Receive sequence on page 524.
State

RXRU RXIDLE RX RXIDLE RXDISABLE

Reception

’X’ P A S0 L S1 PAYLOAD CRC

DISABLED
READY

ADDRESS

PAYLOAD

END
Lifeline

1 2 3
DISABLE
START
RXEN

Figure 116: Receive sequence

An RXRU ramp up sequence is initiated when the RXEN task is triggered. After the radio has successfully
ramped up it will generate the READY event indicating that a packet reception can be initiated. A packet
reception is initiated by triggering the START task. As illustrated in Radio states on page 522 the START
task can first be triggered after the RADIO has entered into the RXIDLE state.
Receive sequence on page 524 illustrates a single packet reception where the CPU manually triggers
the different tasks needed to control the flow of the RADIO, i.e. no shortcuts are used. If shortcuts are
not used, a certain amount of delay caused by CPU execution is expected between READY and START, and
between END and DISABLE. As illustrated Receive sequence on page 524 the RADIO will be listening
and possibly receiving undefined data, represented with an 'X', from START and until a packet with valid
preamble (P) is received.
A slightly modified version of the receive sequence from Receive sequence on page 524 is illustrated
in Receive sequence using shortcuts to avoid delays on page 525 where the RADIO is configured to
use shortcuts between READY and START, and between END and DISABLE, which means that no delay is
introduced.

4413_417 v1.9 524

 Peripherals

State
RXRU RX RXDISABLE

Reception
’X’ P A S0 L S1 PAYLOAD CRC

DISABLED
READY

ADDRESS

PAYLOAD

END
Lifeline

1 2

START

DISABLE
RXEN

Figure 117: Receive sequence using shortcuts to avoid delays

The RADIO is able to receive multiple packets one after the other without having to disable and re-enable
the RADIO between packets as illustrated in Reception of multiple packets on page 525.
State

RXRU RX RXIDLE RX RXDISABLE

Receiver

’X’ P A S0 L S1 PAYLOAD CRC ’X’ P A S0 L S1 PAYLOAD CRC

DISABLED
ADDRESS

ADDRESS
PAYLOAD

PAYLOAD
END
READY

END
Lifeline

1 2 3

DISABLE
START

START
RXEN

Figure 118: Reception of multiple packets

6.20.8 Received signal strength indicator (RSSI)

The RADIO implements a mechanism for measuring the power in the received signal. This feature is called
received signal strength indicator (RSSI).
The RSSI is measured continuously and the value filtered using a single-pole IIR filter. After a signal level
change, the RSSI will settle after approximately RSSISETTLE.
Sampling of the received signal strength is started by using the RSSISTART task. The sample can be read
from the RSSISAMPLE register.
The sample period of the RSSI is defined by RSSIPERIOD. The RSSISAMPLE will hold the filtered received
signal strength after this sample period.
For the RSSI sample to be valid, the RADIO has to be enabled in receive mode (RXEN task) and the
reception has to be started (READY event followed by START task).

6.20.9 Interframe spacing

Interframe spacing is the time interval between two consecutive packets.

4413_417 v1.9 525

 Peripherals

It is defined as the time, in microseconds, from the end of the last bit of the previous packet received and
to the start of the first bit of the subsequent packet that is transmitted. The RADIO is able to enforce this
interval, as specified in the TIFS register, as long as the TIFS is not specified to be shorter than the RADIO's
turnaround time, i.e. the time needed to switch off the receiver, and then switch the transmitter back on.
The TIFS register can be written any time before the last bit on air is received.
This timing is illustrated in the figure below.
Change to MODE OK

Change to SHORTS and

TIFS OK
State

RX RXDISABLE TXRU TX
On air

PAYLOAD CRC P A S0 L S1 PAYLOAD

ADDRESS
DISABLED
PAYLOAD

READY
END
Lifeline

TIFS

START
DISABLE

TXEN

Figure 119: IFS timing detail

As illustrated, the TIFS duration starts after the last bit on air (just before the END event), and elapses with
first bit being transmitted on air (just after READY event).
TIFS is only enforced if END_DISABLE and DISABLED_TXEN or END_DISABLE and DISABLED_RXEN shortcuts
are enabled. TIFS is qualified for use in BLE_1MBIT, BLE_2MBIT, BLE_LR125KBIT, BLE_LR500KBIT and
Ieee802154_250Kbit mode using the default ramp-up mode. SHORTS and TIFS are not double-buffered,
and can be updated at any point in time before the last bit on air is received. The MODE register is double-
buffered and sampled at the TXEN or RXEN task.

6.20.10 Device address match

The device address match feature is tailored for address whitelisting in a Bluetooth low energy and similar
implementations.
This feature enables on-the-fly device address matching while receiving a packet on air. This feature only
works in receive mode and as long as RADIO is configured for little endian, see PCNF1.ENDIAN.
The device address match unit assumes that the 48 first bits of the payload is the device address and
that bit number 6 in S0 is the TxAdd bit. See the Bluetooth Core Specification for more information about
device addresses, TxAdd and whitelisting.
The RADIO is able to listen for eight different device addresses at the same time. These addresses are
specified in a DAB/DAP register pair, one pair per address, in addition to a TxAdd bit configured in the
DACNF register. The DAB register specifies the 32 least significant bits of the device address, while the DAP
register specifies the 16 most significant bits of the device address.
Each of the device addresses can be individually included or excluded from the matching mechanism. This
is configured in the DACNF register.

4413_417 v1.9 526

 Peripherals

6.20.11 Bit counter

The RADIO implements a simple counter that can be configured to generate an event after a specific
number of bits have been transmitted or received.
By using shortcuts, this counter can be started from different events generated by the RADIO and hence
count relative to these.
The bit counter is started by triggering the BCSTART task, and stopped by triggering the BCSTOP task. A
BCMATCH event will be generated when the bit counter has counted the number of bits specified in the
BCC register. The bit counter will continue to count bits until the DISABLED event is generated or until the
BCSTOP task is triggered. The CPU can therefore, after a BCMATCH event, reconfigure the BCC value for
new BCMATCH events within the same packet.
The bit counter can only be started after the RADIO has received the ADDRESS event.
The bit counter will stop and reset on BCSTOP, STOP, END and DISABLE tasks.
The figure below illustrates how the bit counter can be used to generate a BCMATCH event in the
beginning of the packet payload, and again generate a second BCMATCH event after sending 2 bytes (16
bits) of the payload.
State

RXRU RX RXDISABLE

0 1 2
Reception

’X’ P A S0 L S1 PAYLOAD CRC

Assuming that the

combined length
BCMATCH

BCMATCH

of S0, length (L)

READY

and S1 is 12 bits.

DISABLED
ADDRESS

PAYLOAD

END
Lifeline

1 2 3
BCC = 12

DISABLE
BCC = 12 + 16
START

BCSTART
RXEN

BCSTOP

Figure 120: Bit counter example

6.20.12 IEEE 802.15.4 operation

With the MODE=Ieee802154_250kbit the radio module will comply with the IEEE 802.15.4-2006 standard
implementing its 250 kbps 2450MHz O-QPSK PHY.
The IEEE 802.15.4 standard differs from Nordic's proprietary and Bluetooth low energy modes. Obvious
differences are modulation scheme and channel structure, but also packet structure, security and medium
access control.
The main features of the IEEE 802.15.4 mode are:
• Ultra low power 250 kbps 2450MHz IEEE 802.15.4-2006 compliant link
• Clear channel assessment
• Energy detection scan
• CRC generation

6.20.12.1 Packet structure

The IEEE 802.15.4 standard defines an on the air frame/packet that is different from what is used in BLE
mode.

4413_417 v1.9 527

 Peripherals

The following figure provides an overview of the physical frame structure and its timing:
160 µs 32 µs <=4064 µs
PHY protocol data unit (PPDU)
Preamble sequence SFD Length PHY payload
5 octets synchronization header (SHR) 1 octet Maximum 127 octets (PSDU)
(PHR)

MAC protocol data unit (MPDU)

Figure 121: IEEE 802.15.4 frame format - PHY layer frame structure (PPDU)

The standard uses the term octet as storage unit for 8 bits within the PPDU. For timing, the value symbol is
used, and it has the duration of 16 µs.
The total usable payload (PSDU) is 127 octets, but when CRC is being used, this is reduced to 125 octets of
usable payload.
The preamble sequence consists of four octets that are all zero. These are used for the radio receiver to
synchronize on. Following the four octets is a single octet named start of frame delimiter (SFD) with a fixed
value of 0xA7. The user can program an alternative SFD through the SFD register. This feature is provided
for an initial level of frame filtering for those who choose non-standard compliance. It is a valuable feature
when operating in a congested or private network. The preamble sequence and the SFD are generated by
the radio module, and are not programmed by the user into the frame buffer.
The PHY header (PHR) is a single octet following the synchronization header (SHR). The least significant
seven bits denote the frame length of the following PSDU. The most significant bit is reserved and is
set to zero for frames that are standard compliant. The radio module will report all eight bits and it can
potentially be used to carry some information. The PHR is the first byte that will be written to the frame
data memory pointed to by PACKETPTR. Frames with zero length will be discarded, and the FRAMESTART
event will not be generated in this case.
The next N octets will carry the data of the PHY packet, where N equals the value of the PHR. For an
implementation also using the IEEE 802.15.4 MAC layer, the PHY data will be a MAC frame of N-2 octets
since two octets will occupy a CRC field.
An IEEE 802.15.4 MAC frame will always consist of a header (the frame control field (FCF), sequence
number and addressing fields), a payload, and the 16-bit frame control sequence (FCS), as as illustrated in
the figure below.
MAC protocol data unit (MPDU)
FCF Seq Addressing fields MAC payload FCS
MAC header (MHR) MAC service data unit (MSDU) (MFR)

Dst PAN ID Dst address Src PAN ID Src address Security CRC-16

0/4/6/8/10/12/14/16/18/20 octets 0/5/6/10/14 octets 2 octets

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Frame type Sec Pend ACK Comp Reserved Dst A mode Frame ver Src A mode
Frame control field (FCF) 2 octets

Figure 122: IEEE 802.15.4 frame format - MAC layer frame structure (MPDU)

The two FCF octets contain information about what type of frame this is, what addressing it uses, and
other control flags. This field is decoded when using the assisted operating modes offered by the radio.

4413_417 v1.9 528

 Peripherals

The sequence number is a single octet in size and is unique for a frame. It will be used in the associated
acknowledgement frame sent upon successful frame reception.
The addressing field can be zero (acknowledgement frame) or up to 20 octets in size. The field is used to
direct packets to the correct recipient as well as denoting its origin. IEEE 802.15.4 bases it's addressing on
networks being organized in PANs with 16-bit identifier and nodes having a 16-bit or 64-bit address. In the
assisted receive mode, these parameters are analyzed for address matching and acknowledgement.
The MAC payload carries the data of the next higher layer, or in the case of a MAC command frame
information used by the MAC layer itself.
The two last octets contain the 16-bit ITU-T CRC. The FCS is calculated over the MAC header (MHR) and
MAC payload (MSDU) parts of the frame. This field is calculated automatically when sending a frame, or
indicated in the CRCSTATUS register when a frame is received. This feature is taken care of autonomously,
by the CRC module (if configured).

6.20.12.2 Operating frequencies

The IEEE 802.15.4 standard defines 16 channels [11 - 26] of 5 MHz each in the 2450 MHz frequency band.
The FREQUENCY register of the radio module must be programmed according to table below for correct
operation on the center frequency defined for each channel.

IEEE 802.15.4 channel Center frequency (MHz) FREQUENCY setting

Channel 11 2405 5
Channel 12 2410 10
Channel 13 2415 15
Channel 14 2420 20
Channel 15 2425 25
Channel 16 2430 30
Channel 17 2435 35
Channel 18 2440 40
Channel 19 2445 45
Channel 20 2450 50
Channel 21 2455 55
Channel 22 2460 60
Channel 23 2465 65
Channel 24 2470 70
Channel 25 2475 75
Channel 26 2480 80

Table 37: IEEE 802.15.4 center frequency definition

6.20.12.3 Energy detection (ED)

The IEEE 802.15.4 standard requires that it is possible to sample the received signal power within the
bandwidth of a channel for the purpose of determining presence of activity.
There should be no attempt made to decode the signals on the channel, and this is done by disabling
the shortcut between READY event and START task before putting the radio in receive mode. The energy
detection (ED) measurement time where RSSI samples are averaged over is 8 symbol periods (128 µs). The
standard further specifies the measurement to be a number between 0 and 0xFF - where 0 shall indicate
received power less than 10 dB above the selected receiver sensitivity. The power range of the ED values
must be at least 40 dB with a linear mapping with accuracy of ±6 dB. See section 6.9.7 Receiver ED in the
IEEE 802.15.4 standard for further details. An example of an ED scan is given below.

4413_417 v1.9 529

 Peripherals

Below is a code snippet showing how to perform a single energy detection measurement and convert to
IEEE 802.15.4 scale.

#define ED_RSSISCALE 4 // From electrical specifications

uint8_t sample_ed(void)
{
int val;
NRF_RADIO->TASKS_EDSTART = 1; // Start
while (NRF_RADIO->EVENTS_EDEND != 1) {
// CPU can sleep here or do something else
// Use of interrupts are encouraged
}
val = NRF_RADIO->EDSAMPLE; // Read level
return (uint8_t)(val>63 ? 255 : val*ED_RSSISCALE); // Convert to IEEE 802.15.4 scale
}

For scaling between hardware value and dBm, see Conversion between hardware value and dBm on page
531.
It is the mlme-scan.req primitive of the MAC layer that is using the ED measurement to detect channels
where there might be wireless activity. To assist this primitive a taylored mode of operation is available
where the ED measurement runs for a defined number of iterations where it keeps track of the maximum
ED level. This is enganged by writing the EDCNT register to a value different from 0, it will then run the
specified number of iterations reporting the maximum energy measurement in the EDSAMPLE register.
The scan is started with EDSTART task and its end indicated with the EDEND event. This greatly reduces the
interrupt frequency and hence power consumtion. The figure below shows how the ED measurement will
operate depending on the EDCNT register.

EDCNT = 0

EDSTART EDEND

128 µs

EDCNT = N-1

EDSTART EDEND

Scan 0 Scan 1 ... Scan N-1

128*(N) µs

Figure 123: Energy detection measurement examples

An ongoing scan can always be stopped by writing the EDSTOP task. It will be followed by the EDSTOPPED
event when the module has terminated.

6.20.12.4 Clear channel assessment (CCA)

IEEE 802.15.4 implements a listen-before-talk channel access method to avoid collisions when transmitting
- namely carrier sense multiple access with collision avoidance (CSMA-CA). The key part of this is
measuring if the wireless medium is busy or not.

4413_417 v1.9 530

 Peripherals

At least three methods must be supported:

• Mode 1 (energy above threshold): The medium is reported busy upon detecting any energy above the
ED threshold
• Mode 2 (carrier sense only): The medium is reported busy upon detection of a signal compliant with
the IEEE 802.15.4 standard with the same modulation and spreading characteristics
• Mode 3 (carrier sense and threshold): The medium is reported busy by logically ANDing or ORing the
results from mode 1 and mode 2.
It is furthermore specified that the clear channel assessment should survey a period equal to 8 symbols or
128 µs.
The radio module has to be in receive mode and be able to recived correct packets when performing
the CCA. The shortcut between READY and START must be disabled if baseband processing is not to be
performed while the measurement is running.
Mode 1 is enabled by first configuring the field CCAMODE=EdMode in CCACTRL and writing the
CCAEDTHRES field to a chosen value. When the CCASTART task is written the radio module will perform
a ED measurement for 8 symbols and compare the measured level with that found in the CCAEDTHRES
field. If the measured value is higher than or equal to this threshold the CCABUSY event is generated - the
CCAIDLE event is generated if the measured level is less than the threshold.
The conversion from CCAEDTHRES, CCA or EDLEVEL value to dBm can be done with the following
equation, where VALHARDWARE is the hardware-reported values, being either CCAEDTHRES, CCA or
EDLEVEL, and constants ED_RSSISCALE and ED_RSSIOFFS are from electrical specifications:
PRF[dBm] = ED_RSSIOFFS + ED_RSSISCALE x VALHARDWARE
Figure 124: Conversion between hardware value and dBm

Mode 2 is enabled by configuring the CCAMODE=CarrierMode. In carrier mode the module will sample
to see if a valid SFD is found during the 8 symbols. If a valid SFD is seen the CCABUSY event is generated
and the node should not send any data. The CCABUSY event is also generated if the scan was performed
during an ongoing frame reception. In the case where the measurement period completes with no SFD
detection the CCAIDLE task is generated. With the CCA_CORR_COUNT unequal to zero the algorithm
will look at the correlator output in addition to the SFD detection signal. If a SFD is reported during
the scan period it will terminate immidiately indicating busy medium. Similarly, if the number of peaks
above CCA_CORRTHRES crosses the CCA_CORR_COUNT the CCABUSY event is generated. If less than
CCA_CORR_COUNT crossings are found and no SFD is reported the CCAIDLE signal will be generated and it
is ok for the node to commence sending data.
With the CCA_MODE=CarrierAndEdMode or CCA_MODE=CarrierOrEdMode a logical combination of
the result from running both mode 1 and mode 2 is performed. The CCABUSY or CCAIDLE signal will be
generated based on an ANDing or ORing of the internal signals from performing both the energy detection
and carrier detection scans.
An ongoing CCA can always be stopped by issuing the CCASTOP task. This will trigger the associated
CCASTOPPED event.
For CCA mode automation there are three shortcuts available. One is between CCAIDLE and TXEN. This
short must always be used in conjunction with the short between CCAIDLE and STOP. This automation
is provided so that the radio can automatically switch between RX (when performing the CCA) and to
TX where the packet is sent. The last shortcut associated with the CCA mode is between CCABUSY and
DISABLE. This will cause the radio to be disabled whenever the CCA reports a busy medium.
Another handy shortcut is between RXREADY and CCASTART. When the radio has ramped up into RX mode
it can immidiately start a CCA.

4413_417 v1.9 531

 Peripherals

6.20.12.5 Cyclic redundancy check (CRC)

IEEE 802.15.4 uses a 16-bit ITU-T cyclic redundancy check (CRC) calculated over the MAC header (MHR)
and MAC service data unit (MSDU).
The standard defines the following generator polynomial:
G(x) = x16 + x12 + x5 + 1
In receive mode the radio will trigger the CRC module when the first octet after the frame length
(PHR) is received. The CRC will then update on each consecutive octet received. When a complete
frame is received the CRCSTATUS register will be updated accordingly and the EVENTS_CRCOK or
EVENTS_CRCERROR generated. When the CRC module is enabled it will not write the two last octets (CRC)
to the frame Data RAM. When transmitting the CRC will be computed on the fly, starting with the first
octet after PHR, and inserted as the two last octets in the frame. The EasyDMA will fetch frame length - 2
octets from DataRAM and insert the CRC octets insitu.
Below is a code snippet for configuring the CRC module for correct operation when in IEEE 802.15.4 mode.
The CRCCNF is written to 16-bit CRC and the CRCPOLY is written to 0x121. The start value used by IEEE
802.15.4 is zero and CRCINIT is configured to reflect this.

/* 16-bit CRC with ITU-T polynomial with 0 as start condition*/

write_reg(NRFRADIO_REG(CRCCNF), 0x202);
write_reg(NRFRADIO_REG(CRCPOLY), 0x11021);
write_reg(NRFRADIO_REG(CRCINIT), 0);

The ENDIANESS subregister must be set to little-endian since the FCS field is transmitted leftmost bit first.

6.20.12.6 Transmit sequence

The transmission is started by first putting the radio in receive mode sending the RXEN task.
An outline of the IEEE 802.15.4 transmission is illustrated in the figure below.
State

RXRU RXIDLE RX TXRU TXIDLE TX TXIDLE TXDISABLE

Transmitter/Receiver

P
Clear channel SHR H PAYLOAD CRC
R
DISABLED
FRAMESTART
CCAIDLE
READY

READY

END
Lifeline

DISABLE
CCASTART

START
RXEN

TXEN

Figure 125: IEEE 802.15.4 transmit sequence

The receiver will ramp up and enter the RXIDLE state where the READY event is generated. Upon
receiving the ready event the CCA is started by writing to the CCASTART task register. The chosen mode
of assessment (CCA_MODE register) will be performed and signal the CCAIDLE or CCABUSY event 128
µs later. If the CCABUSY is received the radio will have to retry the CCA after a specific back off period as
outlined in the IEEE 802.15.4 standard (see Figure 69 in section 7.5.1.4 The CSMA-CA algorithm of the
standard).
When the CCAIDLE event on the other hand is generated the user shall write to the TXEN task register
to enter the TXRU state. The READY event will be generated when the radio is in TXIDLE state and ready

4413_417 v1.9 532

 Peripherals

to transmit. With the PACKETPTR pointing to the length (PHR) field of the frame the START task can be
written. The radio will send the four octet preamble sequence followed by the start of frame delimiter
(SFD register). The first byte read from the Data RAM is the length field (PHR) followed by the transmission
of the number of bytes indicated as the frame length. If the CRC module is configured it will run for PHR-2
octets. The last two octets will be substituted with the results from running the CRC. The necessary CRC
parameters are sampled on the START task. The FCS field of the frame is little endian.
In addition to the already available shortcuts, one is provided between READY event and CCASTART
task so that a CCA can automatically start when the receiver is ready. And a second shortcut has been
added between CCAIDLE event and the TXEN task so that upon detecting a clear channel the radio can
immediately enter transmit mode.

6.20.12.7 Receive sequence

The reception is started by first putting the radio in receive mode. Writing to the RXEN task the radio will
start ramping up and enter the RXRU state.
When the READY event is generated the radio has entered the RXIDLE mode. For the baseband processing
to be enabled the START task must be written. An outline of the IEEE 802.15.4 reception can be found in
figure below.
State

RXRU RXIDLE RX RXIDLE RXDISABLE

Reception

P
’X’ SHR H PAYLOAD CRC
R
FRAMESTART

DISABLED
READY

END
Lifeline

DISABLE
START
RXEN

Figure 126: IEEE 802.15.4 receive sequence

When a valid SHR is received the radio will start storing future octets (starting with PHR) to the data
memory pointed to by PACKETPTR. After the SFD octet is received the FRAMESTART event is generated.
If the CRC module is enabled it will start updating with the second byte received (first byte in payload)
and run for the full frame length. The two last bytes in the frame is not written to DataRAM when CRC is
configured. However, if the result of the CRC after running the full frame is zero the CRCOK event will be
generated. The END event is generated when the last octet has been received and is available in DataRAM.
When a packet is received a link quality indicator (LQI) is also generated and appended immediately after
the last received octet. When using IEEE 802.15.4 compliant frame this will be just after the MSDU since
the FCS is not reported. In the case of a non-complient frame it will be appended after the full frame. The
LQI reported by hardware must be converted to IEEE 802.15.4 range by an 8-bit saturating multiplication
by 4, as shown in the code example for ED sampling. The LQI is only valid for frames equal to or longer
than three octets. When receiving a frame the RSSI (reported as negative dB) will be measured at three
points during the reception. These three values will be sorted and the middle one selected (median 3) for
then to be remapped within the LQI range. The following figure illustrates the LQI measurement and how
the data is arranged in the DataRAM:

4413_417 v1.9 533

 Peripherals

On air frame

160 µs 32 µs <=4064 µs

PHY protocol data unit (PPDU)

Preamble sequence SFD Length PHY payload
5 octets synchronization header (SHR) 1 octet Maximum 127 octets (PSDU)
(PHR)

MAC protocol data unit (MPDU)

RSSI

RSSI

RSSI
In RAM frame Median 3

Length PHY payload LQI

1 octet Maximum 127 octets (PSDU) 1 octet
FCF
(PHR)
2 octets

MAC protocol data unit (MPDU)

Omitted if CRC enabled

Figure 127: IEEE 802.15.4 frame in Data RAM

A shortcut has been added between FRAMESTART event and the BCSTART task. This can be used to trigger
a BCMATCH event after N bits, such as when inspecting the MAC addressing fields.

6.20.12.8 Interframe spacing (IFS)

The IEEE 802.15.4 standard defines a specific time that is alotted for the MAC sublayer to process received
data. Usage of this interframe spacing (IFS) comes into play to avoid that two frames are transmitted too
close to eachother in time. If the a transmission is requesting an acknowledgement, the speration to the
second frame shall be at least an IFS period.
The IFS is determined to be:
• IFS equals macMinSIFSPeriod (12 symbols) if the MPDU is less than or equal to aMaxSIFSFrameSize (18
octets) octets
• IFS equals macMinLIFSPeriod (40 symbols) if the MPDU is larger than aMaxSIFSFrameSize
Using the efficient assisted modes in the radio module the TIFS will be programmed with the correct value
based on the frame being transmitted. If the assisted modes are not being used the user must update the
TIFS register manually. The figure below provides details on what IFS period is valid in both acknowledged
and unacknowledged transmissions.

4413_417 v1.9 534

 Peripherals

Acknowledged transmission
Long frame ACK Short frame ACK

tack = 32 symbols tlifs = 40 symbols tack = 32 symbols tsifs = 12 symbols

Unacknowledged transmission
Long frame Short frame

tlifs = 40 symbols tsifs = 12 symbols

Figure 128: Interframe spacing examples

6.20.13 EasyDMA
The RADIO uses EasyDMA for reading of data packets from and writing to RAM, without CPU involvement.
As illustrated in RADIO block diagram on page 519, the RADIO's EasyDMA utilizes the same PACKETPTR
for receiving and transmitting packets. This pointer should be reconfigured by the CPU each time before
RADIO is started by the START task. The PACKETPTR registers is double-buffered, meaning that it can be
updated and prepared for the next transmission.

Important: If the PACKETPTR is not pointing to the Data RAM region, an EasyDMA transfer may
result in a HardFault or RAM corruption. See Memory on page 21 for more information about the
different memory regions.

The END event indicates that the last bit has been processed by the radio. The DISABLED event is issued to
acknowledge that a DISABLE task is done.
The structure of a radio packet is described in detail in Packet configuration on page 519. The data that
is stored in Data RAM and transported by EasyDMA consists of the following fields:
• S0
• LENGTH
• S1
• PAYLOAD
In addition, a static add-on is sent immediately after the payload.
The size of each of the above fields in the frame is configurable (see Packet configuration on page 519),
and the space occupied in RAM depends on these settings. A size of zero is possible for any of the fields, it
is up to the user to make sure that the resulting frame complies with the RF protocol chosen.
All fields are extended in size to align with a byte boundary in RAM. For instance a 3 bit long field on air
will occupy 1 byte in RAM while a 9 bit long field will be extended to 2 bytes.
The radio packets elements can be configured as follows:
• CI, TERM1 and TERM2 fields are only present in Bluetooth low energy long range mode
• S0 is configured through the S0LEN field in PCNF0
• LENGTH is configured through the LFLEN field in PCNF0
• S1 is configured through the S1LEN field in PCNF0
• Size of the payload is configured through the value in RAM corresponding to the LENGTH field
• Size of the static add-on to the payload is configured through the STATLEN field in PCNF1
The MAXLEN field in the PCNF1 register configures the maximum packet payload plus add-on size in
number of bytes that can be transmitted or received by the RADIO. This feature can be used to ensure
that the RADIO does not overwrite, or read beyond, the RAM assigned to the packet payload. This means

4413_417 v1.9 535

 Peripherals

that if the packet payload length defined by PCNF1.STATLEN and the LENGTH field in the packet specifies a
packet larger than MAXLEN, the payload will be truncated at MAXLEN.

Note: The MAXLEN includes the payload and the add-on, but excludes the size occupied by the S0,
LENGTH and S1 fields. This has to be taken into account when allocating RAM.

If the payload and add-on length is specified larger than MAXLEN, the RADIO will still transmit or receive in
the same way as before, except the payload is now truncated to MAXLEN. The packet's LENGTH field will
not be altered when the payload is truncated. The RADIO will calculate CRC as if the packet length is equal
to MAXLEN.

Note: If the PACKETPTR is not pointing to the Data RAM region, an EasyDMA transfer may result in
a HardFault or RAM corruption. See Memory on page 21 for more information about the different
memory regions.

The END event indicates that the last bit has been processed by the radio. The DISABLED event is issued to
acknowledge that an DISABLE task is done.

6.20.14 Registers
Instances

Instance Base address Description

RADIO 0x40001000 2.4 GHz radio

Register overview

Register Offset Description

TASKS_TXEN 0x000 Enable RADIO in TX mode
TASKS_RXEN 0x004 Enable RADIO in RX mode
TASKS_START 0x008 Start RADIO
TASKS_STOP 0x00C Stop RADIO
TASKS_DISABLE 0x010 Disable RADIO
TASKS_RSSISTART 0x014 Start the RSSI and take one single sample of the receive signal strength
TASKS_RSSISTOP 0x018 Stop the RSSI measurement
TASKS_BCSTART 0x01C Start the bit counter
TASKS_BCSTOP 0x020 Stop the bit counter
TASKS_EDSTART 0x024 Start the energy detect measurement used in IEEE 802.15.4 mode
TASKS_EDSTOP 0x028 Stop the energy detect measurement
TASKS_CCASTART 0x02C Start the clear channel assessment used in IEEE 802.15.4 mode
TASKS_CCASTOP 0x030 Stop the clear channel assessment
EVENTS_READY 0x100 RADIO has ramped up and is ready to be started
EVENTS_ADDRESS 0x104 Address sent or received
EVENTS_PAYLOAD 0x108 Packet payload sent or received
EVENTS_END 0x10C Packet sent or received
EVENTS_DISABLED 0x110 RADIO has been disabled
EVENTS_DEVMATCH 0x114 A device address match occurred on the last received packet
EVENTS_DEVMISS 0x118 No device address match occurred on the last received packet
EVENTS_RSSIEND 0x11C Sampling of receive signal strength complete
EVENTS_BCMATCH 0x128 Bit counter reached bit count value
EVENTS_CRCOK 0x130 Packet received with CRC ok
EVENTS_CRCERROR 0x134 Packet received with CRC error

4413_417 v1.9 536

 Peripherals

Register Offset Description

EVENTS_FRAMESTART 0x138 IEEE 802.15.4 length field received
EVENTS_EDEND 0x13C Sampling of energy detection complete. A new ED sample is ready for readout from the
RADIO.EDSAMPLE register.
EVENTS_EDSTOPPED 0x140 The sampling of energy detection has stopped
EVENTS_CCAIDLE 0x144 Wireless medium in idle - clear to send
EVENTS_CCABUSY 0x148 Wireless medium busy - do not send
EVENTS_CCASTOPPED 0x14C The CCA has stopped
EVENTS_RATEBOOST 0x150 Ble_LR CI field received, receive mode is changed from Ble_LR125Kbit to Ble_LR500Kbit.
EVENTS_TXREADY 0x154 RADIO has ramped up and is ready to be started TX path
EVENTS_RXREADY 0x158 RADIO has ramped up and is ready to be started RX path
EVENTS_MHRMATCH 0x15C MAC header match found
EVENTS_SYNC 0x168 Preamble indicator.
EVENTS_PHYEND 0x16C Generated in Ble_LR125Kbit, Ble_LR500Kbit and Ieee802154_250Kbit modes when last bit is sent on
air.
SHORTS 0x200 Shortcuts between local events and tasks
INTENSET 0x304 Enable interrupt
INTENCLR 0x308 Disable interrupt
CRCSTATUS 0x400 CRC status
RXMATCH 0x408 Received address
RXCRC 0x40C CRC field of previously received packet
DAI 0x410 Device address match index
PDUSTAT 0x414 Payload status
PACKETPTR 0x504 Packet pointer
FREQUENCY 0x508 Frequency
TXPOWER 0x50C Output power
MODE 0x510 Data rate and modulation
PCNF0 0x514 Packet configuration register 0
PCNF1 0x518 Packet configuration register 1
BASE0 0x51C Base address 0
BASE1 0x520 Base address 1
PREFIX0 0x524 Prefixes bytes for logical addresses 0-3
PREFIX1 0x528 Prefixes bytes for logical addresses 4-7
TXADDRESS 0x52C Transmit address select
RXADDRESSES 0x530 Receive address select
CRCCNF 0x534 CRC configuration
CRCPOLY 0x538 CRC polynomial
CRCINIT 0x53C CRC initial value
TIFS 0x544 Interframe spacing in µs
RSSISAMPLE 0x548 RSSI sample
STATE 0x550 Current radio state
DATAWHITEIV 0x554 Data whitening initial value
BCC 0x560 Bit counter compare
DAB[0] 0x600 Device address base segment 0
DAB[1] 0x604 Device address base segment 1
DAB[2] 0x608 Device address base segment 2
DAB[3] 0x60C Device address base segment 3
DAB[4] 0x610 Device address base segment 4
DAB[5] 0x614 Device address base segment 5
DAB[6] 0x618 Device address base segment 6
DAB[7] 0x61C Device address base segment 7
DAP[0] 0x620 Device address prefix 0
DAP[1] 0x624 Device address prefix 1
DAP[2] 0x628 Device address prefix 2

4413_417 v1.9 537

 Peripherals

Register Offset Description

DAP[3] 0x62C Device address prefix 3
DAP[4] 0x630 Device address prefix 4
DAP[5] 0x634 Device address prefix 5
DAP[6] 0x638 Device address prefix 6
DAP[7] 0x63C Device address prefix 7
DACNF 0x640 Device address match configuration
MHRMATCHCONF 0x644 Search pattern configuration
MHRMATCHMAS 0x648 Pattern mask
MODECNF0 0x650 Radio mode configuration register 0
SFD 0x660 IEEE 802.15.4 start of frame delimiter
EDCNT 0x664 IEEE 802.15.4 energy detect loop count
EDSAMPLE 0x668 IEEE 802.15.4 energy detect level
CCACTRL 0x66C IEEE 802.15.4 clear channel assessment control
POWER 0xFFC Peripheral power control

6.20.14.1 TASKS_TXEN
Address offset: 0x000
Enable RADIO in TX mode

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_TXEN Enable RADIO in TX mode
Trigger 1 Trigger task

6.20.14.2 TASKS_RXEN
Address offset: 0x004
Enable RADIO in RX mode

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_RXEN Enable RADIO in RX mode
Trigger 1 Trigger task

6.20.14.3 TASKS_START
Address offset: 0x008
Start RADIO

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_START Start RADIO
Trigger 1 Trigger task

4413_417 v1.9 538

 Peripherals

6.20.14.4 TASKS_STOP
Address offset: 0x00C
Stop RADIO

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STOP Stop RADIO
Trigger 1 Trigger task

6.20.14.5 TASKS_DISABLE
Address offset: 0x010
Disable RADIO

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_DISABLE Disable RADIO
Trigger 1 Trigger task

6.20.14.6 TASKS_RSSISTART
Address offset: 0x014
Start the RSSI and take one single sample of the receive signal strength

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_RSSISTART Start the RSSI and take one single sample of the receive signal strength
Trigger 1 Trigger task

6.20.14.7 TASKS_RSSISTOP
Address offset: 0x018
Stop the RSSI measurement

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_RSSISTOP Stop the RSSI measurement
Trigger 1 Trigger task

6.20.14.8 TASKS_BCSTART
Address offset: 0x01C

4413_417 v1.9 539

 Peripherals

Start the bit counter

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A
Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_BCSTART Start the bit counter
Trigger 1 Trigger task

6.20.14.9 TASKS_BCSTOP
Address offset: 0x020
Stop the bit counter

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_BCSTOP Stop the bit counter
Trigger 1 Trigger task

6.20.14.10 TASKS_EDSTART
Address offset: 0x024
Start the energy detect measurement used in IEEE 802.15.4 mode

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_EDSTART Start the energy detect measurement used in IEEE 802.15.4 mode
Trigger 1 Trigger task

6.20.14.11 TASKS_EDSTOP
Address offset: 0x028
Stop the energy detect measurement

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_EDSTOP Stop the energy detect measurement
Trigger 1 Trigger task

6.20.14.12 TASKS_CCASTART
Address offset: 0x02C
Start the clear channel assessment used in IEEE 802.15.4 mode

4413_417 v1.9 540

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_CCASTART Start the clear channel assessment used in IEEE 802.15.4 mode
Trigger 1 Trigger task

6.20.14.13 TASKS_CCASTOP
Address offset: 0x030
Stop the clear channel assessment

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_CCASTOP Stop the clear channel assessment
Trigger 1 Trigger task

6.20.14.14 EVENTS_READY
Address offset: 0x100
RADIO has ramped up and is ready to be started

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_READY RADIO has ramped up and is ready to be started
NotGenerated 0 Event not generated
Generated 1 Event generated

6.20.14.15 EVENTS_ADDRESS
Address offset: 0x104
Address sent or received

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_ADDRESS Address sent or received
NotGenerated 0 Event not generated
Generated 1 Event generated

6.20.14.16 EVENTS_PAYLOAD
Address offset: 0x108
Packet payload sent or received

4413_417 v1.9 541

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_PAYLOAD Packet payload sent or received
NotGenerated 0 Event not generated
Generated 1 Event generated

6.20.14.17 EVENTS_END
Address offset: 0x10C
Packet sent or received

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_END Packet sent or received
NotGenerated 0 Event not generated
Generated 1 Event generated

6.20.14.18 EVENTS_DISABLED
Address offset: 0x110
RADIO has been disabled

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_DISABLED RADIO has been disabled
NotGenerated 0 Event not generated
Generated 1 Event generated

6.20.14.19 EVENTS_DEVMATCH
Address offset: 0x114
A device address match occurred on the last received packet

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_DEVMATCH A device address match occurred on the last received packet
NotGenerated 0 Event not generated
Generated 1 Event generated

6.20.14.20 EVENTS_DEVMISS
Address offset: 0x118
No device address match occurred on the last received packet

4413_417 v1.9 542

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_DEVMISS No device address match occurred on the last received packet
NotGenerated 0 Event not generated
Generated 1 Event generated

6.20.14.21 EVENTS_RSSIEND
Address offset: 0x11C
Sampling of receive signal strength complete
A new RSSI sample is ready for readout from the RADIO.RSSISAMPLE register

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_RSSIEND Sampling of receive signal strength complete

A new RSSI sample is ready for readout from the RADIO.RSSISAMPLE

register
NotGenerated 0 Event not generated
Generated 1 Event generated

6.20.14.22 EVENTS_BCMATCH
Address offset: 0x128
Bit counter reached bit count value
Bit counter value is specified in the RADIO.BCC register

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_BCMATCH Bit counter reached bit count value

Bit counter value is specified in the RADIO.BCC register

NotGenerated 0 Event not generated
Generated 1 Event generated

6.20.14.23 EVENTS_CRCOK
Address offset: 0x130
Packet received with CRC ok

4413_417 v1.9 543

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_CRCOK Packet received with CRC ok
NotGenerated 0 Event not generated
Generated 1 Event generated

6.20.14.24 EVENTS_CRCERROR
Address offset: 0x134
Packet received with CRC error

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_CRCERROR Packet received with CRC error
NotGenerated 0 Event not generated
Generated 1 Event generated

6.20.14.25 EVENTS_FRAMESTART
Address offset: 0x138
IEEE 802.15.4 length field received

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_FRAMESTART IEEE 802.15.4 length field received
NotGenerated 0 Event not generated
Generated 1 Event generated

6.20.14.26 EVENTS_EDEND
Address offset: 0x13C
Sampling of energy detection complete. A new ED sample is ready for readout from the RADIO.EDSAMPLE
register.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_EDEND Sampling of energy detection complete. A new ED sample is ready for
readout from the RADIO.EDSAMPLE register.
NotGenerated 0 Event not generated
Generated 1 Event generated

6.20.14.27 EVENTS_EDSTOPPED
Address offset: 0x140

4413_417 v1.9 544

 Peripherals

The sampling of energy detection has stopped

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A
Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_EDSTOPPED The sampling of energy detection has stopped
NotGenerated 0 Event not generated
Generated 1 Event generated

6.20.14.28 EVENTS_CCAIDLE
Address offset: 0x144
Wireless medium in idle - clear to send

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_CCAIDLE Wireless medium in idle - clear to send
NotGenerated 0 Event not generated
Generated 1 Event generated

6.20.14.29 EVENTS_CCABUSY
Address offset: 0x148
Wireless medium busy - do not send

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_CCABUSY Wireless medium busy - do not send
NotGenerated 0 Event not generated
Generated 1 Event generated

6.20.14.30 EVENTS_CCASTOPPED
Address offset: 0x14C
The CCA has stopped

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_CCASTOPPED The CCA has stopped
NotGenerated 0 Event not generated
Generated 1 Event generated

6.20.14.31 EVENTS_RATEBOOST
Address offset: 0x150

4413_417 v1.9 545

 Peripherals

Ble_LR CI field received, receive mode is changed from Ble_LR125Kbit to Ble_LR500Kbit.

Ble_LR CI field received, receive mode is changed from Ble_LR125Kbit to Ble_LR500Kbit.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_RATEBOOST Ble_LR CI field received, receive mode is changed from Ble_LR125Kbit to
Ble_LR500Kbit.

Ble_LR CI field received, receive mode is changed from Ble_LR125Kbit to

Ble_LR500Kbit.
NotGenerated 0 Event not generated
Generated 1 Event generated

6.20.14.32 EVENTS_TXREADY
Address offset: 0x154
RADIO has ramped up and is ready to be started TX path

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_TXREADY RADIO has ramped up and is ready to be started TX path
NotGenerated 0 Event not generated
Generated 1 Event generated

6.20.14.33 EVENTS_RXREADY
Address offset: 0x158
RADIO has ramped up and is ready to be started RX path

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_RXREADY RADIO has ramped up and is ready to be started RX path
NotGenerated 0 Event not generated
Generated 1 Event generated

6.20.14.34 EVENTS_MHRMATCH
Address offset: 0x15C
MAC header match found

4413_417 v1.9 546

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_MHRMATCH MAC header match found
NotGenerated 0 Event not generated
Generated 1 Event generated

6.20.14.35 EVENTS_SYNC
Address offset: 0x168
Preamble indicator.
A possible preamble has been received in Ble_LR125Kbit, Ble_LR500Kbit or Ieee802154_250Kbit modes
during an RX transaction. False triggering of the event is possible.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_SYNC Preamble indicator.

A possible preamble has been received in Ble_LR125Kbit, Ble_LR500Kbit or

Ieee802154_250Kbit modes during an RX transaction. False triggering of the
event is possible.
NotGenerated 0 Event not generated
Generated 1 Event generated

6.20.14.36 EVENTS_PHYEND
Address offset: 0x16C
Generated in Ble_LR125Kbit, Ble_LR500Kbit and Ieee802154_250Kbit modes when last bit is sent on air.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_PHYEND Generated in Ble_LR125Kbit, Ble_LR500Kbit and Ieee802154_250Kbit
modes when last bit is sent on air.
NotGenerated 0 Event not generated
Generated 1 Event generated

6.20.14.37 SHORTS
Address offset: 0x200
Shortcuts between local events and tasks

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID U T S R Q P O N M L K H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW READY_START Shortcut between event READY and task START
Disabled 0 Disable shortcut

4413_417 v1.9 547

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID U T S R Q P O N M L K H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Enabled 1 Enable shortcut
B RW END_DISABLE Shortcut between event END and task DISABLE
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
C RW DISABLED_TXEN Shortcut between event DISABLED and task TXEN
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
D RW DISABLED_RXEN Shortcut between event DISABLED and task RXEN
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
E RW ADDRESS_RSSISTART Shortcut between event ADDRESS and task RSSISTART
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
F RW END_START Shortcut between event END and task START
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
G RW ADDRESS_BCSTART Shortcut between event ADDRESS and task BCSTART
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
H RW DISABLED_RSSISTOP Shortcut between event DISABLED and task RSSISTOP
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
K RW RXREADY_CCASTART Shortcut between event RXREADY and task CCASTART
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
L RW CCAIDLE_TXEN Shortcut between event CCAIDLE and task TXEN
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
M RW CCABUSY_DISABLE Shortcut between event CCABUSY and task DISABLE
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
N RW FRAMESTART_BCSTART Shortcut between event FRAMESTART and task BCSTART
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
O RW READY_EDSTART Shortcut between event READY and task EDSTART
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
P RW EDEND_DISABLE Shortcut between event EDEND and task DISABLE
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
Q RW CCAIDLE_STOP Shortcut between event CCAIDLE and task STOP
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
R RW TXREADY_START Shortcut between event TXREADY and task START
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
S RW RXREADY_START Shortcut between event RXREADY and task START
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
T RW PHYEND_DISABLE Shortcut between event PHYEND and task DISABLE

4413_417 v1.9 548

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID U T S R Q P O N M L K H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
U RW PHYEND_START Shortcut between event PHYEND and task START
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut

6.20.14.38 INTENSET
Address offset: 0x304
Enable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID Z Y V U T S R Q P O N M L K I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW READY Write '1' to enable interrupt for event READY
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW ADDRESS Write '1' to enable interrupt for event ADDRESS
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW PAYLOAD Write '1' to enable interrupt for event PAYLOAD
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
D RW END Write '1' to enable interrupt for event END
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
E RW DISABLED Write '1' to enable interrupt for event DISABLED
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
F RW DEVMATCH Write '1' to enable interrupt for event DEVMATCH
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
G RW DEVMISS Write '1' to enable interrupt for event DEVMISS
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
H RW RSSIEND Write '1' to enable interrupt for event RSSIEND

A new RSSI sample is ready for readout from the RADIO.RSSISAMPLE

register
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

4413_417 v1.9 549

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID Z Y V U T S R Q P O N M L K I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
I RW BCMATCH Write '1' to enable interrupt for event BCMATCH

Bit counter value is specified in the RADIO.BCC register

Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
K RW CRCOK Write '1' to enable interrupt for event CRCOK
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
L RW CRCERROR Write '1' to enable interrupt for event CRCERROR
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
M RW FRAMESTART Write '1' to enable interrupt for event FRAMESTART
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
N RW EDEND Write '1' to enable interrupt for event EDEND
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
O RW EDSTOPPED Write '1' to enable interrupt for event EDSTOPPED
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
P RW CCAIDLE Write '1' to enable interrupt for event CCAIDLE
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
Q RW CCABUSY Write '1' to enable interrupt for event CCABUSY
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
R RW CCASTOPPED Write '1' to enable interrupt for event CCASTOPPED
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
S RW RATEBOOST Write '1' to enable interrupt for event RATEBOOST

Ble_LR CI field received, receive mode is changed from Ble_LR125Kbit to

Ble_LR500Kbit.
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
T RW TXREADY Write '1' to enable interrupt for event TXREADY
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
U RW RXREADY Write '1' to enable interrupt for event RXREADY
Set 1 Enable
Disabled 0 Read: Disabled

4413_417 v1.9 550

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID Z Y V U T S R Q P O N M L K I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Enabled 1 Read: Enabled
V RW MHRMATCH Write '1' to enable interrupt for event MHRMATCH
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
Y RW SYNC Write '1' to enable interrupt for event SYNC

A possible preamble has been received in Ble_LR125Kbit, Ble_LR500Kbit or

Ieee802154_250Kbit modes during an RX transaction. False triggering of the
event is possible.
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
Z RW PHYEND Write '1' to enable interrupt for event PHYEND
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.20.14.39 INTENCLR
Address offset: 0x308
Disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID Z Y V U T S R Q P O N M L K I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW READY Write '1' to disable interrupt for event READY
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW ADDRESS Write '1' to disable interrupt for event ADDRESS
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW PAYLOAD Write '1' to disable interrupt for event PAYLOAD
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
D RW END Write '1' to disable interrupt for event END
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
E RW DISABLED Write '1' to disable interrupt for event DISABLED
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
F RW DEVMATCH Write '1' to disable interrupt for event DEVMATCH
Clear 1 Disable
Disabled 0 Read: Disabled

4413_417 v1.9 551

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID Z Y V U T S R Q P O N M L K I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Enabled 1 Read: Enabled
G RW DEVMISS Write '1' to disable interrupt for event DEVMISS
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
H RW RSSIEND Write '1' to disable interrupt for event RSSIEND

A new RSSI sample is ready for readout from the RADIO.RSSISAMPLE

register
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
I RW BCMATCH Write '1' to disable interrupt for event BCMATCH

Bit counter value is specified in the RADIO.BCC register

Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
K RW CRCOK Write '1' to disable interrupt for event CRCOK
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
L RW CRCERROR Write '1' to disable interrupt for event CRCERROR
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
M RW FRAMESTART Write '1' to disable interrupt for event FRAMESTART
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
N RW EDEND Write '1' to disable interrupt for event EDEND
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
O RW EDSTOPPED Write '1' to disable interrupt for event EDSTOPPED
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
P RW CCAIDLE Write '1' to disable interrupt for event CCAIDLE
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
Q RW CCABUSY Write '1' to disable interrupt for event CCABUSY
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
R RW CCASTOPPED Write '1' to disable interrupt for event CCASTOPPED
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

4413_417 v1.9 552

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID Z Y V U T S R Q P O N M L K I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
S RW RATEBOOST Write '1' to disable interrupt for event RATEBOOST

Ble_LR CI field received, receive mode is changed from Ble_LR125Kbit to

Ble_LR500Kbit.
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
T RW TXREADY Write '1' to disable interrupt for event TXREADY
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
U RW RXREADY Write '1' to disable interrupt for event RXREADY
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
V RW MHRMATCH Write '1' to disable interrupt for event MHRMATCH
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
Y RW SYNC Write '1' to disable interrupt for event SYNC

A possible preamble has been received in Ble_LR125Kbit, Ble_LR500Kbit or

Ieee802154_250Kbit modes during an RX transaction. False triggering of the
event is possible.
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
Z RW PHYEND Write '1' to disable interrupt for event PHYEND
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.20.14.40 CRCSTATUS
Address offset: 0x400
CRC status

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R CRCSTATUS CRC status of packet received
CRCError 0 Packet received with CRC error
CRCOk 1 Packet received with CRC ok

6.20.14.41 RXMATCH
Address offset: 0x408
Received address

4413_417 v1.9 553

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R RXMATCH Received address

Logical address of which previous packet was received

6.20.14.42 RXCRC
Address offset: 0x40C
CRC field of previously received packet

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R RXCRC CRC field of previously received packet

CRC field of previously received packet

6.20.14.43 DAI
Address offset: 0x410
Device address match index

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R DAI Device address match index

Index (n) of device address, see DAB[n] and DAP[n], that got an address
match

6.20.14.44 PDUSTAT
Address offset: 0x414
Payload status

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R PDUSTAT Status on payload length vs. PCNF1.MAXLEN
LessThan 0 Payload less than PCNF1.MAXLEN
GreaterThan 1 Payload greater than PCNF1.MAXLEN
B R CISTAT Status on what rate packet is received with in Long Range
LR125kbit 0 Frame is received at 125kbps
LR500kbit 1 Frame is received at 500kbps

6.20.14.45 PACKETPTR
Address offset: 0x504

4413_417 v1.9 554

 Peripherals

Packet pointer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A
Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PACKETPTR Packet pointer

Packet address to be used for the next transmission or reception. When

transmitting, the packet pointed to by this address will be transmitted and
when receiving, the received packet will be written to this address. This
address is a byte aligned RAM address.

Note: See the memory chapter for details about which memories
are available for EasyDMA.

6.20.14.46 FREQUENCY
Address offset: 0x508
Frequency

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B A A A A A A A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
A RW FREQUENCY [0..100] Radio channel frequency

Frequency = 2400 + FREQUENCY (MHz).

B RW MAP Channel map selection.
Default 0 Channel map between 2400 MHZ .. 2500 MHz

Frequency = 2400 + FREQUENCY (MHz)

Low 1 Channel map between 2360 MHZ .. 2460 MHz

Frequency = 2360 + FREQUENCY (MHz)

6.20.14.47 TXPOWER
Address offset: 0x50C
Output power

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TXPOWER RADIO output power

Output power in number of dBm, i.e. if the value -20 is specified the output
power will be set to -20dBm.
Pos8dBm 0x8 +8 dBm
Pos7dBm 0x7 +7 dBm
Pos6dBm 0x6 +6 dBm
Pos5dBm 0x5 +5 dBm
Pos4dBm 0x4 +4 dBm
Pos3dBm 0x3 +3 dBm

4413_417 v1.9 555

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Pos2dBm 0x2 +2 dBm
0dBm 0x0 0 dBm
Neg4dBm 0xFC -4 dBm
Neg8dBm 0xF8 -8 dBm
Neg12dBm 0xF4 -12 dBm
Neg16dBm 0xF0 -16 dBm
Neg20dBm 0xEC -20 dBm
Neg30dBm 0xE2 -40 dBm

This enumerator is deprecated.

Neg40dBm 0xD8 -40 dBm

6.20.14.48 MODE
Address offset: 0x510
Data rate and modulation

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW MODE Radio data rate and modulation setting. The radio supports frequency-shift
keying (FSK) modulation.
Nrf_1Mbit 0 1 Mbit/s Nordic proprietary radio mode
Nrf_2Mbit 1 2 Mbit/s Nordic proprietary radio mode
Ble_1Mbit 3 1 Mbit/s BLE
Ble_2Mbit 4 2 Mbit/s BLE
Ble_LR125Kbit 5 Long range 125 kbit/s TX, 125 kbit/s and 500 kbit/s RX
Ble_LR500Kbit 6 Long range 500 kbit/s TX, 125 kbit/s and 500 kbit/s RX
Ieee802154_250Kbit 15 IEEE 802.15.4-2006 250 kbit/s

6.20.14.49 PCNF0
Address offset: 0x514
Packet configuration register 0

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID H H G F F E E D C C C C B A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW LFLEN Length on air of LENGTH field in number of bits.
B RW S0LEN Length on air of S0 field in number of bytes.
C RW S1LEN Length on air of S1 field in number of bits.
D RW S1INCL Include or exclude S1 field in RAM
Automatic 0 Include S1 field in RAM only if S1LEN > 0
Include 1 Always include S1 field in RAM independent of S1LEN
E RW CILEN Length of code indicator - long range
F RW PLEN Length of preamble on air. Decision point: TASKS_START task
8bit 0 8-bit preamble

4413_417 v1.9 556

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID H H G F F E E D C C C C B A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
16bit 1 16-bit preamble
32bitZero 2 32-bit zero preamble - used for IEEE 802.15.4
LongRange 3 Preamble - used for BLE long range
G RW CRCINC Indicates if LENGTH field contains CRC or not
Exclude 0 LENGTH does not contain CRC
Include 1 LENGTH includes CRC
H RW TERMLEN Length of TERM field in Long Range operation

6.20.14.50 PCNF1
Address offset: 0x518
Packet configuration register 1

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E D C C C B B B B B B B B A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW MAXLEN [0..255] Maximum length of packet payload. If the packet payload is larger than
MAXLEN, the radio will truncate the payload to MAXLEN.
B RW STATLEN [0..255] Static length in number of bytes

The static length parameter is added to the total length of the payload when
sending and receiving packets, e.g. if the static length is set to N the radio
will receive or send N bytes more than what is defined in the LENGTH field
of the packet.
C RW BALEN [2..4] Base address length in number of bytes

The address field is composed of the base address and the one byte long
address prefix, e.g. set BALEN=2 to get a total address of 3 bytes.
D RW ENDIAN On air endianness of packet, this applies to the S0, LENGTH, S1 and the
PAYLOAD fields.
Little 0 Least significant bit on air first
Big 1 Most significant bit on air first
E RW WHITEEN Enable or disable packet whitening
Disabled 0 Disable
Enabled 1 Enable

6.20.14.51 BASE0
Address offset: 0x51C
Base address 0

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW BASE0 Base address 0

Radio base address 0.

4413_417 v1.9 557

 Peripherals

6.20.14.52 BASE1
Address offset: 0x520
Base address 1

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW BASE1 Base address 1

Radio base address 1.

6.20.14.53 PREFIX0
Address offset: 0x524
Prefixes bytes for logical addresses 0-3

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID D D D D D D D D C C C C C C C C B B B B B B B B A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW AP0 Address prefix 0.
B RW AP1 Address prefix 1.
C RW AP2 Address prefix 2.
D RW AP3 Address prefix 3.

6.20.14.54 PREFIX1
Address offset: 0x528
Prefixes bytes for logical addresses 4-7

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID D D D D D D D D C C C C C C C C B B B B B B B B A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW AP4 Address prefix 4.
B RW AP5 Address prefix 5.
C RW AP6 Address prefix 6.
D RW AP7 Address prefix 7.

6.20.14.55 TXADDRESS
Address offset: 0x52C
Transmit address select

4413_417 v1.9 558

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TXADDRESS Transmit address select

Logical address to be used when transmitting a packet.

6.20.14.56 RXADDRESSES
Address offset: 0x530
Receive address select

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW ADDR0 Enable or disable reception on logical address 0.
Disabled 0 Disable
Enabled 1 Enable
B RW ADDR1 Enable or disable reception on logical address 1.
Disabled 0 Disable
Enabled 1 Enable
C RW ADDR2 Enable or disable reception on logical address 2.
Disabled 0 Disable
Enabled 1 Enable
D RW ADDR3 Enable or disable reception on logical address 3.
Disabled 0 Disable
Enabled 1 Enable
E RW ADDR4 Enable or disable reception on logical address 4.
Disabled 0 Disable
Enabled 1 Enable
F RW ADDR5 Enable or disable reception on logical address 5.
Disabled 0 Disable
Enabled 1 Enable
G RW ADDR6 Enable or disable reception on logical address 6.
Disabled 0 Disable
Enabled 1 Enable
H RW ADDR7 Enable or disable reception on logical address 7.
Disabled 0 Disable
Enabled 1 Enable

6.20.14.57 CRCCNF
Address offset: 0x534
CRC configuration

4413_417 v1.9 559

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B B A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW LEN [1..3] CRC length in number of bytes.

Note: For MODE Ble_LR125Kbit and Ble_LR500Kbit, only LEN set

to 3 is supported

Disabled 0 CRC length is zero and CRC calculation is disabled

One 1 CRC length is one byte and CRC calculation is enabled
Two 2 CRC length is two bytes and CRC calculation is enabled
Three 3 CRC length is three bytes and CRC calculation is enabled
B RW SKIPADDR Include or exclude packet address field out of CRC calculation.
Include 0 CRC calculation includes address field
Skip 1 CRC calculation does not include address field. The CRC calculation will start
at the first byte after the address.
Ieee802154 2 CRC calculation as per 802.15.4 standard. Starting at first byte after length
field.

6.20.14.58 CRCPOLY
Address offset: 0x538
CRC polynomial

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW CRCPOLY CRC polynomial

Each term in the CRC polynomial is mapped to a bit in this register which
index corresponds to the term's exponent. The least significant term/
bit is hard-wired internally to 1, and bit number 0 of the register content
is ignored by the hardware. The following example is for an 8 bit CRC
polynomial: x8 + x7 + x3 + x2 + 1 = 1 1000 1101 .

6.20.14.59 CRCINIT
Address offset: 0x53C
CRC initial value

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW CRCINIT CRC initial value

Initial value for CRC calculation

6.20.14.60 TIFS
Address offset: 0x544
Interframe spacing in µs

4413_417 v1.9 560

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TIFS Interframe spacing in µs

Interframe space is the time interval between two consecutive packets. It

is defined as the time, in microseconds, from the end of the last bit of the
previous packet to the start of the first bit of the subsequent packet.

6.20.14.61 RSSISAMPLE
Address offset: 0x548
RSSI sample

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R RSSISAMPLE [0..127] RSSI sample

RSSI sample result. The value of this register is read as a positive value while
the actual received signal strength is a negative value. Actual received signal
strength is therefore as follows: received signal strength = -A dBm

6.20.14.62 STATE
Address offset: 0x550
Current radio state

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R STATE Current radio state
Disabled 0 RADIO is in the Disabled state
RxRu 1 RADIO is in the RXRU state
RxIdle 2 RADIO is in the RXIDLE state
Rx 3 RADIO is in the RX state
RxDisable 4 RADIO is in the RXDISABLED state
TxRu 9 RADIO is in the TXRU state
TxIdle 10 RADIO is in the TXIDLE state
Tx 11 RADIO is in the TX state
TxDisable 12 RADIO is in the TXDISABLED state

6.20.14.63 DATAWHITEIV
Address offset: 0x554
Data whitening initial value

4413_417 v1.9 561

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000040 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW DATAWHITEIV Data whitening initial value. Bit 6 is hard-wired to '1', writing '0' to it has no
effect, and it will always be read back and used by the device as '1'.

Bit 0 corresponds to Position 6 of the LSFR, Bit 1 to Position 5, etc.

6.20.14.64 BCC
Address offset: 0x560
Bit counter compare

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW BCC Bit counter compare

Bit counter compare register

6.20.14.65 DAB[0]
Address offset: 0x600
Device address base segment 0

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW DAB Device address base segment 0

6.20.14.66 DAB[1]
Address offset: 0x604
Device address base segment 1

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW DAB Device address base segment 1

6.20.14.67 DAB[2]
Address offset: 0x608
Device address base segment 2

4413_417 v1.9 562

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW DAB Device address base segment 2

6.20.14.68 DAB[3]
Address offset: 0x60C
Device address base segment 3

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW DAB Device address base segment 3

6.20.14.69 DAB[4]
Address offset: 0x610
Device address base segment 4

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW DAB Device address base segment 4

6.20.14.70 DAB[5]
Address offset: 0x614
Device address base segment 5

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW DAB Device address base segment 5

6.20.14.71 DAB[6]
Address offset: 0x618
Device address base segment 6

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW DAB Device address base segment 6

4413_417 v1.9 563

 Peripherals

6.20.14.72 DAB[7]
Address offset: 0x61C
Device address base segment 7

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW DAB Device address base segment 7

6.20.14.73 DAP[0]
Address offset: 0x620
Device address prefix 0

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW DAP Device address prefix 0

6.20.14.74 DAP[1]
Address offset: 0x624
Device address prefix 1

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW DAP Device address prefix 1

6.20.14.75 DAP[2]
Address offset: 0x628
Device address prefix 2

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW DAP Device address prefix 2

6.20.14.76 DAP[3]
Address offset: 0x62C
Device address prefix 3

4413_417 v1.9 564

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW DAP Device address prefix 3

6.20.14.77 DAP[4]
Address offset: 0x630
Device address prefix 4

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW DAP Device address prefix 4

6.20.14.78 DAP[5]
Address offset: 0x634
Device address prefix 5

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW DAP Device address prefix 5

6.20.14.79 DAP[6]
Address offset: 0x638
Device address prefix 6

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW DAP Device address prefix 6

6.20.14.80 DAP[7]
Address offset: 0x63C
Device address prefix 7

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW DAP Device address prefix 7

4413_417 v1.9 565

 Peripherals

6.20.14.81 DACNF
Address offset: 0x640
Device address match configuration

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW ENA0 Enable or disable device address matching using device address 0
Disabled 0 Disabled
Enabled 1 Enabled
B RW ENA1 Enable or disable device address matching using device address 1
Disabled 0 Disabled
Enabled 1 Enabled
C RW ENA2 Enable or disable device address matching using device address 2
Disabled 0 Disabled
Enabled 1 Enabled
D RW ENA3 Enable or disable device address matching using device address 3
Disabled 0 Disabled
Enabled 1 Enabled
E RW ENA4 Enable or disable device address matching using device address 4
Disabled 0 Disabled
Enabled 1 Enabled
F RW ENA5 Enable or disable device address matching using device address 5
Disabled 0 Disabled
Enabled 1 Enabled
G RW ENA6 Enable or disable device address matching using device address 6
Disabled 0 Disabled
Enabled 1 Enabled
H RW ENA7 Enable or disable device address matching using device address 7
Disabled 0 Disabled
Enabled 1 Enabled
I RW TXADD0 TxAdd for device address 0
J RW TXADD1 TxAdd for device address 1
K RW TXADD2 TxAdd for device address 2
L RW TXADD3 TxAdd for device address 3
M RW TXADD4 TxAdd for device address 4
N RW TXADD5 TxAdd for device address 5
O RW TXADD6 TxAdd for device address 6
P RW TXADD7 TxAdd for device address 7

6.20.14.82 MHRMATCHCONF
Address offset: 0x644
Search pattern configuration

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW MHRMATCHCONF Search pattern configuration

4413_417 v1.9 566

 Peripherals

6.20.14.83 MHRMATCHMAS
Address offset: 0x648
Pattern mask

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW MHRMATCHMAS Pattern mask

6.20.14.84 MODECNF0
Address offset: 0x650
Radio mode configuration register 0

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B B A

Reset 0x00000200 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW RU Radio ramp-up time
Default 0 Default ramp-up time (tRXEN and tTXEN), compatible with firmware written
for nRF51
Fast 1 Fast ramp-up (tRXEN,FAST and tTXEN,FAST), see electrical specification for
more information

When enabled, TIFS is not enforced by hardware and software needs to

control when to turn on the Radio.
B RW DTX Default TX value

Specifies what the RADIO will transmit when it is not started, i.e. between:

RADIO.EVENTS_READY and RADIO.TASKS_START

RADIO.EVENTS_END and RADIO.TASKS_START

RADIO.EVENTS_END and RADIO.EVENTS_DISABLED

Note: For 802.15.4 and BLE LR mode, only Center is a valid

setting

B1 0 Transmit '1'
B0 1 Transmit '0'
Center 2 Transmit center frequency

When tuning the crystal for centre frequency, the RADIO must be set in DTX
= Center mode to be able to achieve the expected accuracy

6.20.14.85 SFD
Address offset: 0x660
IEEE 802.15.4 start of frame delimiter

4413_417 v1.9 567

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A

Reset 0x000000A7 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 0 1 1 1
ID R/W Field Value ID Value Description
A RW SFD IEEE 802.15.4 start of frame delimiter

6.20.14.86 EDCNT
Address offset: 0x664
IEEE 802.15.4 energy detect loop count
Number of iterations to perform an ED scan. If set to 0 one scan is performed, otherwise the specified
number + 1 of ED scans will be performed and the max ED value tracked in EDSAMPLE

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EDCNT IEEE 802.15.4 energy detect loop count

6.20.14.87 EDSAMPLE
Address offset: 0x668
IEEE 802.15.4 energy detect level

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EDLVL [0..127] IEEE 802.15.4 energy detect level

Register value must be converted to IEEE 802.15.4 range by an 8-bit

saturating multiplication by factor ED_RSSISCALE, as shown in the code
example for ED sampling

6.20.14.88 CCACTRL
Address offset: 0x66C
IEEE 802.15.4 clear channel assessment control

4413_417 v1.9 568

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID D D D D D D D D C C C C C C C C B B B B B B B B A A A

Reset 0x052D0000 0 0 0 0 0 1 0 1 0 0 1 0 1 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW CCAMODE CCA mode of operation
EdMode 0 Energy above threshold

Will report busy whenever energy is detected above CCAEDTHRES

CarrierMode 1 Carrier seen

Will report busy whenever compliant IEEE 802.15.4 signal is seen

CarrierAndEdMode 2 Energy above threshold AND carrier seen
CarrierOrEdMode 3 Energy above threshold OR carrier seen
EdModeTest1 4 Energy above threshold test mode that will abort when first ED
measurement over threshold is seen. No averaging.
B RW CCAEDTHRES CCA energy busy threshold. Used in all the CCA modes except CarrierMode.

Must be converted from IEEE 802.15.4 range by dividing by factor

ED_RSSISCALE - similar to EDSAMPLE register
C RW CCACORRTHRES CCA correlator busy threshold. Only relevant to CarrierMode,
CarrierAndEdMode and CarrierOrEdMode.
D RW CCACORRCNT Limit for occurances above CCACORRTHRES. When not equal to zero the
corrolator based signal detect is enabled.

6.20.14.89 POWER
Address offset: 0xFFC
Peripheral power control

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000001 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
ID R/W Field Value ID Value Description
A RW POWER Peripheral power control. The peripheral and its registers will be reset to its
initial state by switching the peripheral off and then back on again.
Disabled 0 Peripheral is powered off
Enabled 1 Peripheral is powered on

6.20.15 Electrical specification

6.20.15.1 General radio characteristics

Symbol Description Min. Typ. Max. Units

fOP Operating frequencies 2360 2500 MHz
fPLL,CH,SP PLL channel spacing 1 MHz
fDELTA,1M Frequency deviation @ 1 Mbps ±170 kHz
fDELTA,BLE,1M Frequency deviation @ BLE 1 Mbps ±250 kHz
fDELTA,2M Frequency deviation @ 2 Mbps ±320 kHz
fDELTA,BLE,2M Frequency deviation @ BLE 2 Mbps ±500 kHz
fskBPS On-the-air data rate 125 2000 kbps
fchip, IEEE 802.15.4 Chip rate in IEEE 802.15.4 mode 2000 kchip/s

4413_417 v1.9 569

 Peripherals

6.20.15.2 Radio current consumption (transmitter)

Symbol Description Min. Typ. Max. Units

ITX,PLUS8dBM,DCDC TX only run current (DC/DC, 3 V) PRF = +8 dBm 14.8 mA
ITX,PLUS8dBM TX only run current PRF = +8 dBm 32.7 mA
ITX,PLUS4dBM,DCDC TX only run current (DC/DC, 3 V) PRF = +4 dBm 9.6 mA
ITX,PLUS4dBM TX only run current PRF = +4 dBm 21.4 mA
ITX,0dBM,DCDC,5V,REG0HIGH. TX only run current (DC/DC, 5 V, REG0 out = 3.3 V)PRF = 0 dBm 3.0 mA
ITX,0dBM,DCDC,5V,REG0LOW TX only run current (DC/DC, 5 V, REG0 out = 1.8 V)PRF = 0 dBm 3.0 mA
ITX,0dBM,DCDC TX only run current (DC/DC, 3 V)PRF = 0 dBm 4.8 mA
ITX,0dBM TX only run current PRF = 0 dBm 10.6 mA
ITX,MINUS4dBM,DCDC TX only run current DC/DC, 3 V PRF = -4 dBm 3.1 mA
ITX,MINUS4dBM TX only run current PRF = -4 dBm 8.1 mA
ITX,MINUS8dBM,DCDC TX only run current DC/DC, 3 V PRF = -8 dBm 3.3 mA
ITX,MINUS8dBM TX only run current PRF = -8 dBm 7.2 mA
ITX,MINUS12dBM,DCDC TX only run current DC/DC, 3 V PRF = -12 dBm 3.0 mA
ITX,MINUS12dBM TX only run current PRF = -12 dBm 6.4 mA
ITX,MINUS16dBM,DCDC TX only run current DC/DC, 3 V PRF = -16 dBm 2.8 mA
ITX,MINUS16dBM TX only run current PRF = -16 dBm 6.0 mA
ITX,MINUS20dBM,DCDC TX only run current DC/DC, 3 V PRF = -20 dBm 2.7 mA
ITX,MINUS20dBM TX only run current PRF = -20 dBm 5.6 mA
ITX,MINUS40dBM,DCDC TX only run current DC/DC, 3 V PRF = -40 dBm 2.3 mA
ITX,MINUS40dBM TX only run current PRF = -40 dBm 4.6 mA
ISTART,TX,DCDC TX start-up current DC/DC, 3 V, PRF = 4 dBm 5.2 mA
ISTART,TX TX start-up current, PRF = 4 dBm 11.0 mA

6.20.15.3 Radio current consumption (Receiver)

Symbol Description Min. Typ. Max. Units

IRX,1M,DCDC RX only run current (DC/DC, 3 V) 1 Mbps/1 Mbps BLE 4.6 mA
IRX,1M RX only run current (LDO, 3 V) 1 Mbps/1 Mbps BLE 9.9 mA
IRX,2M,DCDC RX only run current (DC/DC, 3 V) 2 Mbps/2 Mbps BLE 5.2 mA
IRX,2M RX only run current (LDO, 3 V) 2 Mbps/2 Mbps BLE 11.1 mA
ISTART,RX,1M,DCDC RX start-up current (DC/DC, 3 V) 1 Mbps/1 Mbps BLE 3.7 mA
ISTART,RX,1M RX start-up current 1 Mbps/1 Mbps BLE 6.7 mA

6.20.15.4 Transmitter specification

Symbol Description Min. Typ. Max. Units

PRF Maximum output power 8.0 dBm
PRFC RF power control range 28.0 dB
PRFCR RF power accuracy ±4 dB
PRF1,1 1st Adjacent Channel Transmit Power 1 MHz (1 Mbps) -24.8 dBc
PRF2,1 2nd Adjacent Channel Transmit Power 2 MHz (1 Mbps) -54.0 dBc
PRF1,2 1st Adjacent Channel Transmit Power 2 MHz (2 Mbps) -25 dBc
PRF2,2 2nd Adjacent Channel Transmit Power 4 MHz (2 Mbps) -54.0 dBc
Evm Error vector magnitude IEEE 802.15.4 8 %rms
Pharm2nd, IEEE 802.15.4 2nd harmonics in IEEE 802.15.4 mode -51.0 dBm
Pharm3rd, IEEE 802.15.4 3rd harmonics in IEEE 802.15.4 -48.0 dBm

4413_417 v1.9 570

 Peripherals

Symbol Description Min. Typ. Max. Units

PACP,R, IEEE 802.15.4 IEEE 802.15.4 Relative adjacent Channel Power, offset > 3.5 MHz 19 -42 dBc

PACP,A, IEEE 802.15.4 IEEE 802 15.4 Absolute adjacent Channel Power, offset > 3.5 MHz 19 -46 dBm

7.9

7.8

7.7
Output power [dBm]

7.6

7.5

7.4

7.3

7.2

7.1

7
1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6

Supply voltage [V]

-40 ºC 25 ºC 85 ºC

Figure 129: Output power, 1 Mbps Bluetooth low energy

mode, at maximum TXPOWER setting (typical values)

19
Output power set to maximum TXPOWER setting, resolution bandwidth (RBW) set to 100 kHz, and
transmitter Duty-Cycle approximately 85%.

4413_417 v1.9 571

 Peripherals

0.5

Output power [dBm] 0

-0.5

-1

-1.5

-2

-2.5
1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6

Supply voltage [V]

-40 ºC 25 ºC 85 ºC

Figure 130: Output power, 1 Mbps Bluetooth low energy mode, at 0 dBm TXPOWER setting (typical values)

6.20.15.5 Receiver operation

Symbol Description Min. Typ. Max. Units

PRX,MAX Maximum received signal strength at < 0.1% PER 0 dBm
PSENS,IT,1M Sensitivity, 1 Mbps nRF mode ideal transmitter 20 -93 dBm

PSENS,IT,2M Sensitivity, 2 Mbps nRF mode ideal transmitter21 -89 dBm

PSENS,IT,SP,1M,BLE Sensitivity, 1 Mbps BLE ideal transmitter, packet length ≤ 37 bytes BER=1E-3 22 -95 dBm

PSENS,IT,LP,1M,BLE Sensitivity, 1 Mbps BLE ideal transmitter, packet length ≥ 128 bytes BER=1E-4 -94 dBm
23

PSENS,IT,SP,2M,BLE Sensitivity, 2 Mbps BLE ideal transmitter, packet length ≤ 37 bytes -92 dBm
PSENS,IT,BLE LE125k Sensitivity, 125 kbps BLE mode -103 dBm
PSENS,IT,BLE LE500k Sensitivity, 500 kbps BLE mode -99 dBm
PSENS,IEEE 802.15.4 Sensitivity in IEEE 802.15.4 mode -100 dBm

20
Typical sensitivity applies when ADDR0 is used for receiver address correlation. When ADDR[1...7]
are used for receiver address correlation, the typical sensitivity for this mode is degraded by 3 dB.
21
Typical sensitivity applies when ADDR0 is used for receiver address correlation. When ADDR[1..7] are
used for receiver address correlation, the typical sensitivity for this mode is degraded by 3 dB.
22
As defined in the Bluetooth Core Specification v4.0 Volume 6: Core System Package (Low Energy
Controller Volume)
23
Equivalent BER limit < 10E-04

4413_417 v1.9 572

 Peripherals

-93

-93.5

-94
Sensitivity [dBm]

-94.5

-95

-95.5

-96
1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6

Supply voltage [V]

-40 ºC 25 ºC 85 ºC

Figure 131: Sensitivity, 1 Mbps Bluetooth low energy mode, Regulator = LDO (typical values)

6.20.15.6 RX selectivity
RX selectivity with equal modulation on interfering signal24

Symbol Description Min. Typ. Max. Units

C/I1M,co-channel 1Mbps mode, Co-Channel interference 9 dB
C/I1M,-1MHz 1 Mbps mode, Adjacent (-1 MHz) interference -2 dB
C/I1M,+1MHz 1 Mbps mode, Adjacent (+1 MHz) interference -10 dB
C/I1M,-2MHz 1 Mbps mode, Adjacent (-2 MHz) interference -19 dB
C/I1M,+2MHz 1 Mbps mode, Adjacent (+2 MHz) interference -42 dB
C/I1M,-3MHz 1 Mbps mode, Adjacent (-3 MHz) interference -38 dB
C/I1M,+3MHz 1 Mbps mode, Adjacent (+3 MHz) interference -48 dB
C/I1M,±6MHz 1 Mbps mode, Adjacent (≥6 MHz) interference -50 dB
C/I1MBLE,co-channel 1 Mbps BLE mode, Co-Channel interference 6 dB
C/I1MBLE,-1MHz 1 Mbps BLE mode, Adjacent (-1 MHz) interference -2 dB
C/I1MBLE,+1MHz 1 Mbps BLE mode, Adjacent (+1 MHz) interference -9 dB
C/I1MBLE,-2MHz 1 Mbps BLE mode, Adjacent (-2 MHz) interference -22 dB
C/I1MBLE,+2MHz 1 Mbps BLE mode, Adjacent (+2 MHz) interference -46 dB
C/I1MBLE,>3MHz 1 Mbps BLE mode, Adjacent (≥3 MHz) interference -50 dB
C/I1MBLE,image Image frequency interference -22 dB
C/I1MBLE,image,1MHz Adjacent (1 MHz) interference to in-band image frequency -35 dB
C/I2M,co-channel 2 Mbps mode, Co-Channel interference 10 dB
C/I2M,-2MHz 2 Mbps mode, Adjacent (-2 MHz) interference 6 dB
C/I2M,+2MHz 2 Mbps mode, Adjacent (+2 MHz) interference -19 dB
C/I2M,-4MHz 2 Mbps mode, Adjacent (-4 MHz) interference -20 dB
C/I2M,+4MHz 2 Mbps mode, Adjacent (+4 MHz) interference -44 dB

24
Desired signal level at PIN = -67 dBm. One interferer is used, having equal modulation as the desired
signal. The input power of the interferer where the sensitivity equals BER = 0.1% is presented

4413_417 v1.9 573

 Peripherals

Symbol Description Min. Typ. Max. Units

C/I2M,-6MHz 2 Mbps mode, Adjacent (-6 MHz) interference -42 dB
C/I2M,+6MHz 2 Mbps mode, Adjacent (+6 MHz) interference -42 dB
C/I2M,≥12MHz 2 Mbps mode, Adjacent (≥12 MHz) interference -52 dB
C/I2MBLE,co-channel 2 Mbps BLE mode, Co-Channel interference 6.8 dB
C/I2MBLE,±2MHz 2 Mbps BLE mode, Adjacent (±2 MHz) interference -10 dB
C/I2MBLE,±4MHz 2 Mbps BLE mode, Adjacent (±4 MHz) interference -45 dB
C/I2MBLE,≥6MHz 2 Mbps BLE mode, Adjacent (≥6 MHz) interference -48 dB
C/I2MBLE,image Image frequency interference -24 dB
C/I2MBLE,image, 2MHz Adjacent (2 MHz) interference to in-band image frequency -35 dB
C/I125k BLE LR,co-channel 125 kbps BLE LR mode, Co-Channel interference 4.4 dB
C/I125k BLE LR,-1MHz 125 kbps BLE LR mode, Adjacent (-1 MHz) interference -4.0 dB
C/I125k BLE LR,+1MHz 125 kbps BLE LR mode, Adjacent (+1 MHz) interference -12 dB
C/I125k BLE LR,-2MHz 125 kbps BLE LR mode, Adjacent (-2 MHz) interference -28 dB
C/I125k BLE LR,+2MHz 125 kbps BLE LR mode, Adjacent (+2 MHz) interference -50 dB
C/I125k BLE LR,>3MHz 125 kbps BLE LR mode, Adjacent (≥3 MHz) interference -55 dB
C/I125k BLE LR,image Image frequency interference -29 dB

6.20.15.7 RX intermodulation
RX intermodulation25

Symbol Description Min. Typ. Max. Units

PIMD,5TH,1M IMD performance, 1 Mbps, 5th offset channel, packet length ≤ 37 bytes -33 dBm
PIMD,5TH,1M,BLE IMD performance, BLE 1 Mbps, 5th offset channel, packet length ≤ 37 bytes -30 dBm
PIMD,5TH,2M IMD performance, 2 Mbps, 5th offset channel, packet length ≤ 37 bytes -33 dBm
PIMD,5TH,2M,BLE IMD performance, BLE 2 Mbps, 5th offset channel, packet length ≤ 37 bytes -31 dBm

6.20.15.8 Radio timing

Symbol Description Min. Typ. Max. Units

tTXEN,BLE,1M Time between TXEN task and READY event after channel FREQUENCY 140 140 µs
configured (1 Mbps BLE and 150 µs TIFS)
tTXEN,FAST,BLE,1M Time between TXEN task and READY event after channel FREQUENCY 40 40 µs
configured (1 Mbps BLE with fast ramp-up and 150 µs TIFS)
tTXDIS,BLE,1M When in TX, delay between DISABLE task and DISABLED event for MODE = 6 6 µs
Nrf_1Mbit and MODE = Ble_1Mbit
tRXEN,BLE,1M Time between the RXEN task and READY event after channel FREQUENCY 140 140 µs
configured (1 Mbps BLE)
tRXEN,FAST,BLE,1M Time between the RXEN task and READY event after channel FREQUENCY 40 40 µs
configured (1 Mbps BLE with fast ramp-up)
tRXDIS,BLE,1M When in RX, delay between DISABLE task and DISABLED event for MODE = 0 0 µs
Nrf_1Mbit and MODE = Ble_1Mbit
tTXDIS,BLE,2M When in TX, delay between DISABLE task and DISABLED event for MODE = 4 4 µs
Nrf_2Mbit and MODE = Ble_2Mbit
tRXDIS,BLE,2M When in RX, delay between DISABLE task and DISABLED event for MODE = 0 0 µs
Nrf_2Mbit and MODE = Ble_2Mbit
tTXEN,IEEE 802.15.4 Time between TXEN task and READY event after channel FREQUENCY 130 130 µs
configured (IEEE 802.15.4)

25
Desired signal level at PIN = -64 dBm. Two interferers with equal input power are used. The interferer
closest in frequency is not modulated, the other interferer is modulated equal with the desired
signal. The input power of the interferers where the sensitivity equals BER = 0.1% is presented.

4413_417 v1.9 574

 Peripherals

Symbol Description Min. Typ. Max. Units

tTXEN,FAST,IEEE 802.15.4 Time between TXEN task and READY event after channel FREQUENCY 40 40 µs
configured (IEEE 802.15.4 with fast ramp-up)
tTXDIS,IEEE 802.15.4 When in TX, delay between DISABLE task and DISABLED event (IEEE 802.15.4) 21 21 µs
tRXEN,IEEE 802.15.4 Time between the RXEN task and READY event after channel FREQUENCY 130 130 µs
configured (IEEE 802.15.4)
tRXEN,FAST,IEEE 802.15.4 Time between the RXEN task and READY event after channel FREQUENCY 40 40 µs
configured (IEEE 802.15.4 with fast ramp-up)
tRXDIS,IEEE 802.15.4 When in RX, delay between DISABLE task and DISABLED event (IEEE 802.15.4) 0.5 0.5 µs
tRX-to-TX turnaround Maximum TX-to-RX or RX-to-TX turnaround time in IEEE 802.15.4 mode 40 µs

6.20.15.9 Received signal strength indicator (RSSI) specifications

Symbol Description Min. Typ. Max. Units

RSSIACC RSSI accuracy valid range -90 to -20 dBm ±2 dB
RSSIRESOLUTION RSSI resolution 1 dB
RSSIPERIOD RSSI sampling time from RSSI_START task 0.25 µs
RSSISETTLE RSSI settling time after signal level change 15 µs

6.20.15.10 Jitter

Symbol Description Min. Typ. Max. Units

tDISABLEDJITTER Jitter on DISABLED event relative to END event when shortcut between END 0.25 µs
and DISABLE is enabled
tREADYJITTER Jitter on READY event relative to TXEN and RXEN task 0.25 µs

6.20.15.11 IEEE 802.15.4 energy detection constants

Symbol Description Min. Typ. Max. Units

ED_RSSISCALE Scaling value when converting between hardware-reported value and dBm 4 4 4
ED_RSSIOFFS Offset value when converting between hardware-reported value and dBm -92 -92 -92

6.21 RNG — Random number generator

The Random number generator (RNG) generates true non-deterministic random numbers based on
internal thermal noise that are suitable for cryptographic purposes. The RNG does not require a seed
value.

START Random number VALRDY

generator
STOP VALUE

Figure 132: Random number generator

The RNG is started by triggering the START task and stopped by triggering the STOP task. When started,
new random numbers are generated continuously and written to the VALUE register when ready. A
VALRDY event is generated for every new random number that is written to the VALUE register. This means
that after a VALRDY event is generated, the CPU has the time until the next VALRDY event to read out the
random number from the VALUE register before it is overwritten by a new random number.

4413_417 v1.9 575

 Peripherals

6.21.1 Bias correction

A bias correction algorithm is employed on the internal bit stream to remove any bias toward 1 or 0. The
bits are then queued into an eight-bit register for parallel readout from the VALUE register.
It is possible to enable bias correction in the CONFIG register. This will result in slower value generation,
but will ensure a statistically uniform distribution of the random values.

6.21.2 Speed
The time needed to generate one random byte of data is unpredictable, and may vary from one byte to
the next. This is especially true when bias correction is enabled.

6.21.3 Registers
Instances

Instance Base address Description

RNG 0x4000D000 Random number generator

Register overview

Register Offset Description

TASKS_START 0x000 Task starting the random number generator
TASKS_STOP 0x004 Task stopping the random number generator
EVENTS_VALRDY 0x100 Event being generated for every new random number written to the VALUE register
SHORTS 0x200 Shortcuts between local events and tasks
INTENSET 0x304 Enable interrupt
INTENCLR 0x308 Disable interrupt
CONFIG 0x504 Configuration register
VALUE 0x508 Output random number

6.21.3.1 TASKS_START
Address offset: 0x000
Task starting the random number generator

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_START Task starting the random number generator
Trigger 1 Trigger task

6.21.3.2 TASKS_STOP
Address offset: 0x004
Task stopping the random number generator

4413_417 v1.9 576

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STOP Task stopping the random number generator
Trigger 1 Trigger task

6.21.3.3 EVENTS_VALRDY
Address offset: 0x100
Event being generated for every new random number written to the VALUE register

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_VALRDY Event being generated for every new random number written to the VALUE
register
NotGenerated 0 Event not generated
Generated 1 Event generated

6.21.3.4 SHORTS
Address offset: 0x200
Shortcuts between local events and tasks

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW VALRDY_STOP Shortcut between event VALRDY and task STOP
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut

6.21.3.5 INTENSET
Address offset: 0x304
Enable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW VALRDY Write '1' to enable interrupt for event VALRDY
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.21.3.6 INTENCLR
Address offset: 0x308
Disable interrupt

4413_417 v1.9 577

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW VALRDY Write '1' to disable interrupt for event VALRDY
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.21.3.7 CONFIG
Address offset: 0x504
Configuration register

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW DERCEN Bias correction
Disabled 0 Disabled
Enabled 1 Enabled

6.21.3.8 VALUE
Address offset: 0x508
Output random number

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R VALUE [0..255] Generated random number

6.21.4 Electrical specification

6.21.4.1 RNG Electrical Specification

Symbol Description Min. Typ. Max. Units

tRNG,START Time from setting the START task to generation begins. This is a one-time 128 µs
delay on START signal and does not apply between samples.
tRNG,RAW Run time per byte without bias correction. Uniform distribution of 0 and 1 is 30 µs
not guaranteed.
tRNG,BC Run time per byte with bias correction. Uniform distribution of 0 and 1 is 120 µs
guaranteed. Time to generate a byte cannot be guaranteed.

6.22 RTC — Real-time counter

The Real-time counter (RTC) module provides a generic, low power timer on the low-frequency clock
source (LFCLK).

4413_417 v1.9 578

 Peripherals

32.768 kHz

START task PRESCALER event

TICK

COUNTER
STOP task

event
OVRFLW
RTC
CLEAR task

TRIGOVRFLW CC[0:3] event

COMPARE[0..N]
task

Figure 133: RTC block schematic

The RTC module features a 24-bit COUNTER, a 12-bit (1/X) prescaler, capture/compare registers, and a tick
event generator for low power, tickless RTOS implementation.

6.22.1 Clock source

The RTC runs off the LFCLK.
The COUNTER resolution is 30.517 µs. Depending on the source, the RTC is able to run while the HFCLK is
OFF and PCLK16M is not available.
The software has to explicitly start LFCLK before using the RTC.
See CLOCK — Clock control on page 156 for more information about clock sources.

6.22.2 Resolution versus overflow and the PRESCALER

Counter increment frequency:

fRTC [kHz] = 32.768 / (PRESCALER + 1 )

The PRESCALER register is read/write when the RTC is stopped. The PRESCALER register is read-only once
the RTC is STARTed. Writing to the PRESCALER register when the RTC is started has no effect.
The PRESCALER is restarted on START, CLEAR, and TRIGOVRFLW, meaning the prescaler value is latched to
an internal register (<<PRESC>>) on these tasks.
Examples of different frequency configurations are as following:
• Desired COUNTER frequency 100 Hz (10 ms counter period)
PRESCALER = round(32.768 kHz / 100 Hz) - 1 = 327
fRTC = 99.9 Hz
10009.576 μs counter period
• Desired COUNTER frequency 8 Hz (125 ms counter period)
PRESCALER = round(32.768 kHz / 8 Hz) – 1 = 4095
fRTC = 8 Hz

4413_417 v1.9 579

 Peripherals

125 ms counter period

Prescaler Counter resolution Overflow

0 30.517 μs 512 seconds
28-1 7812.5 μs 131072 seconds
12
2 -1 125 ms 582.542 hours

Table 38: RTC resolution versus overflow

6.22.3 COUNTER register

The COUNTER increments on LFCLK when the internal PRESCALER register (<<PRESC>>) is 0x00.
<<PRESC>> is reloaded from the PRESCALER register. If enabled, the TICK event occurs on each increment
of the COUNTER. The TICK event is disabled by default.
SysClk

LFClk

TICK

PRESC 0x000

<<PRESC>> 0x000 0x000 0x000 0x000

COUNTER 0x000000 0x000001 0x000002 0x000003

Figure 134: Timing diagram - COUNTER_PRESCALER_0

SysClk

LFClk

TICK

PRESC 0x001

<<PRESC>> 0x000 0x001 0x000 0x001

COUNTER 0x000000 0x000001

Figure 135: Timing diagram - COUNTER_PRESCALER_1

6.22.4 Overflow features

The TRIGOVRFLW task sets the COUNTER value to 0xFFFFF0 to allow SW test of the overflow condition.
OVRFLW occurs when COUNTER overflows from 0xFFFFFF to 0.

Note: The OVRFLW event is disabled by default.

6.22.5 TICK event

The TICK event enables low power tickless RTOS implementation as it optionally provides a regular
interrupt source for a RTOS without the need to use the ARM SysTick feature.
Using the RTC TICK event rather than the SysTick allows the CPU to be powered down while still keeping
RTOS scheduling active.

4413_417 v1.9 580

 Peripherals

Note: The TICK event is disabled by default.

6.22.6 Event control feature

To optimize RTC power consumption, events in the RTC can be individually disabled to prevent PCLK16M
and HFCLK being requested when those events are triggered. This is managed using the EVTEN register.
For example, if the TICK event is not required for an application, this event should be disabled as it is
frequently occurring and may increase power consumption if HFCLK otherwise could be powered down for
long durations.
This means that the RTC implements a slightly different task and event system compared to the standard
system described in Peripheral interface on page 172. The RTC task and event system is illustrated in
Tasks, events, and interrupts in the RTC on page 581.

Task signal from PPI

RTC

write
TASK

OR

task

RTC
core

event

EVTEN m INTEN m

EVENT m
IRQ signal to NVIC

Event signal to PPI

Figure 136: Tasks, events, and interrupts in the RTC

6.22.7 Compare feature

There are a number of Compare registers.
For more information, see Registers on page 586.
When setting a compare register, the following behavior of the RTC compare event should be noted:
• If a CC register value is 0 when a CLEAR task is set, this will not trigger a COMPARE event.

4413_417 v1.9 581

 Peripherals

SysClk

LFClk

PRESC 0x000

COUNTER X 0x000000

CLEAR

CC[0] 0x000000

COMPARE[0] 0

Figure 137: Timing diagram - COMPARE_CLEAR

• If a CC register is N and the COUNTER value is N when the START task is set, this will not trigger a
COMPARE event.
SysClk

LFClk

PRESC 0x000

COUNTER N-1 N N+1

START

CC[0] N

COMPARE[0] 0

Figure 138: Timing diagram - COMPARE_START

• COMPARE occurs when a CC register is N and the COUNTER value transitions from N-1 to N.
SysClk

LFClk

PRESC 0x000

COUNTER N-2 N-1 N N+1

CC[0] N

COMPARE[0] 0 1

Figure 139: Timing diagram - COMPARE

• If the COUNTER is N, writing N+2 to a CC register is guaranteed to trigger a COMPARE event at N+2.

4413_417 v1.9 582

 Peripherals

SysClk

LFClk

PRESC 0x000

COUNTER N-1 N N+1 N+2

> 62.5 ns

CC[0] X N+2

COMPARE[0] 0 1

Figure 140: Timing diagram - COMPARE_N+2

• If the COUNTER is N, writing N or N+1 to a CC register may not trigger a COMPARE event.
SysClk

LFClk

PRESC 0x000

COUNTER N-2 N-1 N N+1

≥0
CC[0] X N+1

COMPARE[0] 0

Figure 141: Timing diagram - COMPARE_N+1

• If the COUNTER is N and the current CC register value is N+1 or N+2 when a new CC value is written, a
match may trigger on the previous CC value before the new value takes effect. If the current CC value is
greater than N+2 when the new value is written, there will be no event due to the old value.
SysClk

LFClk

PRESC 0x000

COUNTER N-2 N-1 N N+1

≥0
CC[0] N X

COMPARE[0] 0 1

Figure 142: Timing diagram - COMPARE_N-1

6.22.8 TASK and EVENT jitter/delay

Jitter or delay in the RTC is due to the peripheral clock being a low frequency clock (LFCLK) which is not
synchronous to the faster PCLK16M.
Registers in the peripheral interface, part of the PCLK16M domain, have a set of mirrored registers in the
LFCLK domain. For example, the COUNTER value accessible from the CPU is in the PCLK16M domain and
is latched on read from an internal register called COUNTER in the LFCLK domain. COUNTER is the register
which is actually modified each time the RTC ticks. These registers must be synchronised between clock
domains (PCLK16M and LFCLK).

4413_417 v1.9 583

 Peripherals

The following is a summary of the jitter introduced on tasks and events.

Task Delay
CLEAR, STOP, START, TRIGOVRFLOW +15 to 46 μs

Table 39: RTC jitter magnitudes on tasks

Operation/Function Jitter
START to COUNTER increment +/- 15 μs

COMPARE to COMPARE 26 +/- 62.5 ns

Table 40: RTC jitter magnitudes on events

Note: 32.768 kHz clock jitter is additional to the numbers provided above.

CLEAR and STOP (and TRIGOVRFLW; not shown) will be delayed as long as it takes for the peripheral to
clock a falling edge and rising of the LFCLK. This is between 15.2585 μs and 45.7755 μs – rounded to 15 μs
and 46 μs for the remainder of the section.
SysClk
CLEAR

LFClk

PRESC 0x000

COUNTER X X+1 0x000000 0x000001

CLEARa 0 or more SysClk after

≤ ~46 µs
≥ ~15 µs
CLEARb 1 or more SysClk before

Figure 143: Timing diagram - DELAY_CLEAR

SysClk
STOP

LFClk

PRESC 0x000

COUNTER X X+1

STOPa 0 or more SysClk after

≤ ~46 µs
≥ ~15 µs
STOPb 1 or more SysClk before

Figure 144: Timing diagram - DELAY_STOP

The START task will start the RTC. Assuming that the LFCLK was previously running and stable, the first
increment of COUNTER (and instance of TICK event) will be typically after 30.5 μs +/-15 μs. In some
cases, in particular if the RTC is STARTed before the LFCLK is running, that timing can be up to ~250 μs.
The software should therefore wait for the first TICK if it has to make sure the RTC is running. Sending a

26
Assumes RTC runs continuously between these events.

4413_417 v1.9 584

 Peripherals

TRIGOVRFLW task sets the COUNTER to a value close to overflow. However, since the update of COUNTER
relies on a stable LFCLK, sending this task while LFCLK is not running will start LFCLK, but the update will
then be delayed by the same amount of time of up to ~250 μs. The figures show the shortest and longest
delays on the START task which appears as a +/-15 μs jitter on the first COUNTER increment.
SysClk
First tick

LFClk

PRESC 0x000

COUNTER X X+1 X+2 X+3

≥ ~15 µs
START 0 or more SysClk before

Figure 145: Timing diagram - JITTER_START-

SysClk
First tick

LFClk

PRESC 0x000

COUNTER X X+1 X+2

≤ ~250 µs
START

Figure 146: Timing diagram - JITTER_START+

6.22.9 Reading the COUNTER register

To read the COUNTER register, the internal <<COUNTER>> value is sampled.
To ensure that the <<COUNTER>> is safely sampled (considering an LFCLK transition may occur during a
read), the CPU and core memory bus are halted for three cycles by lowering the core PREADY signal. The
Read takes the CPU 2 cycles in addition resulting in the COUNTER register read taking a fixed five PCLK16M
clock cycles.
SysClk

PREADY

LFClk

<<COUNTER>> N-1 N

COUNTER X N

375.2 ns

COUNTER_READ

Figure 147: Timing diagram - COUNTER_READ

4413_417 v1.9 585

 Peripherals

6.22.10 Registers
Instances

Instance Base address Description

RTC0 0x4000B000 Real-time counter 0
RTC1 0x40011000 Real-time counter 1
RTC2 0x40024000 Real-time counter 2

Configuration

Instance Configuration
RTC0 CC[0..2] implemented, CC[3] not implemented
RTC1 CC[0..3] implemented
RTC2 CC[0..3] implemented

Register overview

Register Offset Description

TASKS_START 0x000 Start RTC COUNTER
TASKS_STOP 0x004 Stop RTC COUNTER
TASKS_CLEAR 0x008 Clear RTC COUNTER
TASKS_TRIGOVRFLW 0x00C Set COUNTER to 0xFFFFF0
EVENTS_TICK 0x100 Event on COUNTER increment
EVENTS_OVRFLW 0x104 Event on COUNTER overflow
EVENTS_COMPARE[0] 0x140 Compare event on CC[0] match
EVENTS_COMPARE[1] 0x144 Compare event on CC[1] match
EVENTS_COMPARE[2] 0x148 Compare event on CC[2] match
EVENTS_COMPARE[3] 0x14C Compare event on CC[3] match
INTENSET 0x304 Enable interrupt
INTENCLR 0x308 Disable interrupt
EVTEN 0x340 Enable or disable event routing
EVTENSET 0x344 Enable event routing
EVTENCLR 0x348 Disable event routing
COUNTER 0x504 Current COUNTER value
PRESCALER 0x508 12 bit prescaler for COUNTER frequency (32768/(PRESCALER+1)). Must be written when RTC is
stopped.
CC[0] 0x540 Compare register 0
CC[1] 0x544 Compare register 1
CC[2] 0x548 Compare register 2
CC[3] 0x54C Compare register 3

6.22.10.1 TASKS_START
Address offset: 0x000
Start RTC COUNTER

4413_417 v1.9 586

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_START Start RTC COUNTER
Trigger 1 Trigger task

6.22.10.2 TASKS_STOP
Address offset: 0x004
Stop RTC COUNTER

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STOP Stop RTC COUNTER
Trigger 1 Trigger task

6.22.10.3 TASKS_CLEAR
Address offset: 0x008
Clear RTC COUNTER

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_CLEAR Clear RTC COUNTER
Trigger 1 Trigger task

6.22.10.4 TASKS_TRIGOVRFLW
Address offset: 0x00C
Set COUNTER to 0xFFFFF0

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_TRIGOVRFLW Set COUNTER to 0xFFFFF0
Trigger 1 Trigger task

6.22.10.5 EVENTS_TICK
Address offset: 0x100
Event on COUNTER increment

4413_417 v1.9 587

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_TICK Event on COUNTER increment
NotGenerated 0 Event not generated
Generated 1 Event generated

6.22.10.6 EVENTS_OVRFLW
Address offset: 0x104
Event on COUNTER overflow

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_OVRFLW Event on COUNTER overflow
NotGenerated 0 Event not generated
Generated 1 Event generated

6.22.10.7 EVENTS_COMPARE[0]
Address offset: 0x140
Compare event on CC[0] match

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_COMPARE Compare event on CC[0] match
NotGenerated 0 Event not generated
Generated 1 Event generated

6.22.10.8 EVENTS_COMPARE[1]
Address offset: 0x144
Compare event on CC[1] match

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_COMPARE Compare event on CC[1] match
NotGenerated 0 Event not generated
Generated 1 Event generated

6.22.10.9 EVENTS_COMPARE[2]
Address offset: 0x148
Compare event on CC[2] match

4413_417 v1.9 588

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_COMPARE Compare event on CC[2] match
NotGenerated 0 Event not generated
Generated 1 Event generated

6.22.10.10 EVENTS_COMPARE[3]
Address offset: 0x14C
Compare event on CC[3] match

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_COMPARE Compare event on CC[3] match
NotGenerated 0 Event not generated
Generated 1 Event generated

6.22.10.11 INTENSET
Address offset: 0x304
Enable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TICK Write '1' to enable interrupt for event TICK
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW OVRFLW Write '1' to enable interrupt for event OVRFLW
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW COMPARE[0] Write '1' to enable interrupt for event COMPARE[0]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
D RW COMPARE[1] Write '1' to enable interrupt for event COMPARE[1]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
E RW COMPARE[2] Write '1' to enable interrupt for event COMPARE[2]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
F RW COMPARE[3] Write '1' to enable interrupt for event COMPARE[3]
Set 1 Enable
Disabled 0 Read: Disabled

4413_417 v1.9 589

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Enabled 1 Read: Enabled

6.22.10.12 INTENCLR
Address offset: 0x308
Disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TICK Write '1' to disable interrupt for event TICK
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW OVRFLW Write '1' to disable interrupt for event OVRFLW
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW COMPARE[0] Write '1' to disable interrupt for event COMPARE[0]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
D RW COMPARE[1] Write '1' to disable interrupt for event COMPARE[1]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
E RW COMPARE[2] Write '1' to disable interrupt for event COMPARE[2]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
F RW COMPARE[3] Write '1' to disable interrupt for event COMPARE[3]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.22.10.13 EVTEN
Address offset: 0x340
Enable or disable event routing

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TICK Enable or disable event routing for event TICK
Disabled 0 Disable
Enabled 1 Enable
B RW OVRFLW Enable or disable event routing for event OVRFLW

4413_417 v1.9 590

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Disabled 0 Disable
Enabled 1 Enable
C RW COMPARE[0] Enable or disable event routing for event COMPARE[0]
Disabled 0 Disable
Enabled 1 Enable
D RW COMPARE[1] Enable or disable event routing for event COMPARE[1]
Disabled 0 Disable
Enabled 1 Enable
E RW COMPARE[2] Enable or disable event routing for event COMPARE[2]
Disabled 0 Disable
Enabled 1 Enable
F RW COMPARE[3] Enable or disable event routing for event COMPARE[3]
Disabled 0 Disable
Enabled 1 Enable

6.22.10.14 EVTENSET
Address offset: 0x344
Enable event routing

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TICK Write '1' to enable event routing for event TICK
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
Set 1 Enable
B RW OVRFLW Write '1' to enable event routing for event OVRFLW
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
Set 1 Enable
C RW COMPARE[0] Write '1' to enable event routing for event COMPARE[0]
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
Set 1 Enable
D RW COMPARE[1] Write '1' to enable event routing for event COMPARE[1]
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
Set 1 Enable
E RW COMPARE[2] Write '1' to enable event routing for event COMPARE[2]
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
Set 1 Enable
F RW COMPARE[3] Write '1' to enable event routing for event COMPARE[3]
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
Set 1 Enable

4413_417 v1.9 591

 Peripherals

6.22.10.15 EVTENCLR
Address offset: 0x348
Disable event routing

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TICK Write '1' to disable event routing for event TICK
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
Clear 1 Disable
B RW OVRFLW Write '1' to disable event routing for event OVRFLW
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
Clear 1 Disable
C RW COMPARE[0] Write '1' to disable event routing for event COMPARE[0]
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
Clear 1 Disable
D RW COMPARE[1] Write '1' to disable event routing for event COMPARE[1]
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
Clear 1 Disable
E RW COMPARE[2] Write '1' to disable event routing for event COMPARE[2]
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
Clear 1 Disable
F RW COMPARE[3] Write '1' to disable event routing for event COMPARE[3]
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
Clear 1 Disable

6.22.10.16 COUNTER
Address offset: 0x504
Current COUNTER value

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R COUNTER Counter value

6.22.10.17 PRESCALER
Address offset: 0x508
12 bit prescaler for COUNTER frequency (32768/(PRESCALER+1)). Must be written when RTC is stopped.

4413_417 v1.9 592

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PRESCALER Prescaler value

6.22.10.18 CC[0]
Address offset: 0x540
Compare register 0

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW COMPARE Compare value

6.22.10.19 CC[1]
Address offset: 0x544
Compare register 1

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW COMPARE Compare value

6.22.10.20 CC[2]
Address offset: 0x548
Compare register 2

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW COMPARE Compare value

6.22.10.21 CC[3]
Address offset: 0x54C
Compare register 3

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW COMPARE Compare value

4413_417 v1.9 593

 Peripherals

6.23 SAADC — Successive approximation analog-to-

digital converter
The SAADC peripheral is a differential successive approximation register (SAR) analog-to-digital converter.
The main features of the SAADC are the following:
• 8/10/12-bit resolution, 14-bit resolution with oversampling
• Up to eight channels for single-ended inputs and four channels for differential inputs, depending on
the package variant
• Full scale input range (0 V to VDD)
• Multiple inputs
• Input pins AIN0 to AIN7
• VDD input
• VDDHDIV5 input
• Individual reference selection for each channel
• VDD
• Internal reference
• Continuous sampling
• Output samples automatically stored in RAM using EasyDMA as 16-bit two's complement values
• Internal resistor string

PSEL_A PSEL_A
PSEL_A
PSEL_A
PSEL_A PSEL_A
PSEL_A
PSEL_A
PSEL_A PSEL_A
PSEL_A
PSEL_A
CH[X].PSELP CH[X].CONFIG

NC
AIN0 SAADC
AIN1
AIN2 RAM

AIN3
AIN4 MUX
AIN5 RESULT
P
AIN6 RESP RESULT
AIN7
VDD RESULT

VDDHDIV5 SAR
GAIN EasyDMA RESULT
core
NC RESULT

AIN0 N
RESULT
AIN1 RESN RESULT
AIN2
RESULT
AIN3
AIN4 MUX RESULT.PTR

AIN5
AIN6
AIN7
VDD VDD
START REFSEL STARTED
VDDHDIV5 Internal reference
SAMPLE END
STOP STOPPED

CH[X].PSELN
PSEL_A
PSEL_A
PSEL_A
PSEL_A
PSEL_A
PSEL_A

Figure 148: Block diagram

6.23.1 Channel and input configuration

Up to eight SAADC channels can be enabled and configured for SAADC.
A channel is connected to an analog input using the registers CH[n].PSELP and CH[n].PSELN. Each SAADC
channel can be configured to use either single-ended mode or differential input mode. Setting register
CH[n].PSELP enables the corresponding channel. Setting register CH[n].PSELN has no effect for single-
ended channels.

4413_417 v1.9 594

 Peripherals

Register CH[n].CONFIG configures SAADC channels. In Single-ended mode, the negative channel input is
shorted to ground internally. In Single-ended mode, the assumption is that the internal ground of the ADC
is the same as the external ground that the measured voltage is referred to. This makes SAADC sensitive to
ground bounce on the PCB. To avoid this, use the differential input mode instead.
Before sampling is started, the length and location of the memory buffer in RAM must be configured.
Use registers RESULT.MAXCNT on page 633 and RESULT.PTR on page 632 to configure the length
and location where the output values are to be written. The START task must be triggered to apply the
configuration. See EasyDMA on page 598 for details on memory configuration and how the results are
stored in memory.
SAADC is stopped by triggering the STOP task. The STOP task also terminates the ongoing sampling. SAADC
generates a STOPPED event when it has stopped. If SAADC is not started when the STOP task is triggered,
the STOPPED event is still generated.

6.23.1.1 Shared resources

The SAADC peripheral shares analog resources with other analog peripherals.
While it is possible to use COMP and SAADC at the same time, selecting the same analog input pin for
both peripherals is not supported.

6.23.1.2 Acquisition time

To sample input voltage, SAADC connects a capacitor to the input, as shown in the following figure.
SAADC
Rsource

TACQ

Figure 149: Simplified SAADC sample network

Acquisition time is the amount of time the capacitor is connected, see the TACQ field in the CH[n].CONFIG
register. The required acquisition time depends on the source resistance Rsource. For high source
resistance, increase the acquisition time according to the following table:

TACQ [µs] Maximum source resistance [kΩ]

3 10
5 40
10 100
15 200
20 400
40 800

Table 41: Acquisition time

When using VDDHDIV5 as input, the acquisition time must be 10 µs or longer.

6.23.1.3 Internal resistor string (resistor ladder)

SAADC has an internal resistor string for positive and negative input. The resistors are controlled in register
CH[n].CONFIG.

4413_417 v1.9 595

 Peripherals

The following figure illustrates the resistor ladder for positive and negative input:

RESP = Pullup

R
Input Output

RESP = Pulldown

Figure 150: Resistor ladder for positive input (negative input is equivalent, using RESN instead of RESP)

6.23.1.4 Reference voltage and gain settings

Each SAADC channel can have individual reference and gain settings. These settings are configured in
register CH[n].CONFIG.
The following configuration options are available:
• VDD/4 or internal 0.6 V reference
• Gain ranging from 1/6 to 4
The gain setting controls the effective input range of SAADC, as shown in the following equation:

Input range = (±0.6 V or ±VDD/4)/gain

For example, selecting VDD as reference, single-ended input (grounded negative input), and a gain of 1/4
gives the following input range:

Input range = (VDD/4)/(1/4) = VDD

With internal reference, single-ended input (grounded negative input) and a gain of 1/6, the input range is
the following:

Input range = (0.6 V)/(1/6) = 3.6 V

Inputs AIN0 to AIN7 cannot exceed VDD or be lower than VSS.

6.23.2 Operation modes

The SAADC configuration supports Single-channel Single Conversion mode, Single-channel Continuous
Conversion mode, and scan mode. Only one mode can be enabled at a time.
Single-channel sampling happens in either Single Conversion mode or Continuous Conversion mode. Scan
mode is entered when more than one channel is enabled.
Oversampling can be used to improve the signal-to-noise ratio (SNR). It is not recommended to use
oversampling for scan mode. For more information about oversampling, see Oversampling on page 597.

4413_417 v1.9 596

 Peripherals

6.23.2.1 Single-channel Single Conversion mode

SAADC performs one conversion of a single channel and stops once complete.
This mode of operation is configured by enabling only one of the available channels defined by the
registers CH[n].PSELP, CH[n].PSELN, and CH[n].CONFIG. When the SAMPLE task is triggered, SAADC starts
sampling the input voltage.
A DONE event signals that the sample was taken. In this mode, the RESULTDONE and DONE events
are equal when oversampling does not happen. Both events can occur before EasyDMA transfers the
value to RAM. For more information, see EasyDMA on page 598. The END event is generated when
RESULT.MAXCNT on page 633 values are transferred to RAM.

6.23.2.2 Single-channel Continuous Conversion mode

In Single-channel Continuous Conversion mode, a single channel is sampled continuously.
Continuous sampling is achieved with an internal timer in the SAADC peripheral. The register SAMPLERATE
on page 632 configures the Single-channel Continuous Conversion mode and sample rate.
The sample rate must fulfill the following criteria:

fSAMPLE < 1 / (tACQ + tconv)

When Single-channel Continuous Conversion mode is selected, SAADC is started by triggering the SAMPLE
task once. Triggering the STOP task stops sampling. A DONE event signals that one sample was taken.
In this mode, the RESULTDONE and DONE events are equal when oversampling does not happen. Both
events may occur before EasyDMA transfers the value to RAM. For more information, see EasyDMA on
page 598. The END event is generated when RESULT.MAXCNT on page 633 values are transferred to
RAM.

6.23.2.3 Scan mode

If more than one channel is enabled, SAADC functions in scan mode.
In scan mode, one SAMPLE task triggers one conversion per enabled channel.
The time it takes to sample all channels is less than the sum of the conversion time of all enabled
channels. The conversion time for a channel is defined as the sum of the acquisition time tACQ and the
conversion time tCONV.
The events DONE and RESULTDONE are generated when one sample is taken. Both events may occur
before EasyDMA transfers the values into RAM, see EasyDMA on page 598 for more information.

Note: Continuous conversion mode is not supported in scan mode.

6.23.2.4 Oversampling
An accumulator in SAADC can be used to find the average of several analog input samples. In general,
oversampling improves the signal-to-noise ratio (SNR). Oversampling does not improve the integral non-
linearity (INL) or differential non-linearity (DNL).
Oversampling is configured in register OVERSAMPLE. When oversampling, 2OVERSAMPLE samples are
averaged before one result is transferred to memory. The mode used to sample the input determines
when and how those samples are taken.
When oversampling is configured, DONE event is generated for every input sample taken. RESULTDONE
event is generated for every averaged value ready to be transferred into RAM. END event is generated
when RESULT.MAXCNT averaged values are transferred into RAM.

4413_417 v1.9 597

 Peripherals

Note: Oversampling should only be used when a single input channel is enabled, as averaging is
performed over all enabled channels.

6.23.3 Digital output

The digital output value is calculated using the following formula.

RESULT = [V(P) – V(N)] * (GAIN/REFERENCE) * 2(RESOLUTION - m)

where V(P) is the voltage at input P, V(N) is the voltage at input N, GAIN is the selected gain,
REFERENCE is the selected reference voltage, RESOLUTION is output resolution in bits, as configured
in register RESOLUTION on page 631, and m being 0 for single-ended channels and 1 for differential
channels.
Results are sign extended to 16 bits and stored in RAM in little-endian byte order.
Results generated by SAADC deviate due to DC errors like offset, gain, differential non-linearity (DNL), and
integral non-linearity (INL). See Electrical specification for details on these parameters. The result can also
vary due to AC errors like non-linearities in the gain block, settling errors due to high source impedance,
and sampling jitter. DC errors affect the most for battery measurement.

6.23.4 EasyDMA
SAADC resources are started by triggering the START task. The SAADC uses EasyDMA to store results in a
buffer in RAM.
Registers RESULT.PTR on page 632 and RESULT.MAXCNT on page 633 must be configured before
SAADC is started.
The result buffer is located at the address specified in register RESULT.PTR on page 632. This register
is double-buffered, and it can be updated and prepared for the next START task immediately after the
STARTED event is generated. Register RESULT.MAXCNT on page 633 specifies the size of the result
buffer. SAADC generates an END event when the result buffer is full, as shown in the following figure.
Data RAM

0x20000000
Result 0
0x20000002
Result 1

0x20000010
Result 2
0x20000012
Result 3

0x20000020
0
0x20000022
0
SAADC

Sample and convert RAM Sample and convert RAM Sample and convert RAM Sample and convert RAM
STARTED
STARTED

END

END
Lifeline

1 2 3
RESULT.PTR = 0x20000000

RESULT.PTR = 0x20000010

RESULT.PTR = 0x20000020
SAMPLE

SAMPLE
SAMPLE

SAMPLE
RESULT.MAX

START
START
CNT

Figure 151: SAADC

The following figure provides an example of results in Data RAM with an even RESULT.MAXCNT on page
633 and channels 1, 2, and 5 enabled.

4413_417 v1.9 598

 Peripherals

31 16 15 0

RESULT.PTR CH[2] 1st result CH[1] 1st result

RESULT.PTR + 4 CH[1] 2nd result CH[5] 1st result

RESULT.PTR + 8 CH[5] 2nd result CH[2] 2nd result

(…)

RESULT.PTR + 2*RESULT.MAXCNT – 4 CH[5] last result CH[2] last result

Figure 152: Example of RAM placement (even RESULT.MAXCNT), channels 1, 2, and 5 enabled

The following figure provides an example of results in Data RAM with an odd RESULT.MAXCNT on page
633 and channels 1, 2, and 5 enabled.
31 16 15 0

RESULT.PTR CH[2] 1st result CH[1] 1st result

RESULT.PTR + 4 CH[1] 2nd result CH[5] 1st result

RESULT.PTR + 8 CH[5] 2nd result CH[2] 2nd result

(…)

RESULT.PTR + 2*RESULT.MAXCNT – 2 CH[5] last result

Figure 153: Example of RAM placement (odd RESULT.MAXCNT), channels 1, 2, and 5 enabled

The last 32-bit word is populated with only one 16-bit result.
See Memory on page 21 for more information about the different memory regions.
EasyDMA is finished accessing RAM when events END or STOPPED are generated. To see the number
of results transferred to the RAM result buffer since the START task was triggered, read register
RESULT.AMOUNT on page 633.

6.23.5 Event monitoring using limits

Using limits allows event monitoring on channels.
A high and low limit can be configured in the CH[n].LIMIT register. The high limit must be higher than or
equal to the low limit.
Relevant events are generated when the conversion results (sampled input signals) are outside of the
defined limits. It is not possible to generate an event when the input signal is inside a defined range by
switching the high and low limit. An example of event monitoring using limits is illustrated in the following
figure:

4413_417 v1.9 599

 Peripherals

VIN

CH[n].LIMIT.HIGH

CH[n].LIMIT.LOW

events

EVENTS_CH[n].LIMITH

EVENTS_CH[n].LIMITH

EVENTS_CH[n].LIMITH

EVENTS_CH[n].LIMITL
Figure 154: Event monitoring on channel[n] using limits

Limit comparison does not need to be enabled. If event monitoring is not required, related events should
be ignored.

6.23.6 Calibration
The SAADC peripheral has a temperature dependent offset.
It is recommended to calibrate SAADC at least once before use, and recalibrate when the ambient
temperature changes by more than 10°C.
Offset calibration is started by triggering the CALIBRATEOFFSET task. The CALIBRATEDONE event is
generated when calibration is finished.

6.23.7 Registers
Instances

Instance Base address Description

SAADC 0x40007000 Analog to digital converter

Register overview

Register Offset Description

TASKS_START 0x000 Starts the SAADC and prepares the result buffer in RAM
TASKS_SAMPLE 0x004 Takes one SAADC sample
TASKS_STOP 0x008 Stops the SAADC and terminates all on-going conversions
TASKS_CALIBRATEOFFSET 0x00C Starts offset auto-calibration
EVENTS_STARTED 0x100 The SAADC has started

4413_417 v1.9 600

 Peripherals

Register Offset Description

EVENTS_END 0x104 The SAADC has filled up the result buffer
EVENTS_DONE 0x108 A conversion task has been completed. Depending on the configuration, multiple conversions might
be needed for a result to be transferred to RAM.
EVENTS_RESULTDONE 0x10C Result ready for transfer to RAM
EVENTS_CALIBRATEDONE 0x110 Calibration is complete
EVENTS_STOPPED 0x114 The SAADC has stopped
EVENTS_CH[0].LIMITH 0x118 Last result is equal or above CH[0].LIMIT.HIGH
EVENTS_CH[0].LIMITL 0x11C Last result is equal or below CH[0].LIMIT.LOW
EVENTS_CH[1].LIMITH 0x120 Last result is equal or above CH[1].LIMIT.HIGH
EVENTS_CH[1].LIMITL 0x124 Last result is equal or below CH[1].LIMIT.LOW
EVENTS_CH[2].LIMITH 0x128 Last result is equal or above CH[2].LIMIT.HIGH
EVENTS_CH[2].LIMITL 0x12C Last result is equal or below CH[2].LIMIT.LOW
EVENTS_CH[3].LIMITH 0x130 Last result is equal or above CH[3].LIMIT.HIGH
EVENTS_CH[3].LIMITL 0x134 Last result is equal or below CH[3].LIMIT.LOW
EVENTS_CH[4].LIMITH 0x138 Last result is equal or above CH[4].LIMIT.HIGH
EVENTS_CH[4].LIMITL 0x13C Last result is equal or below CH[4].LIMIT.LOW
EVENTS_CH[5].LIMITH 0x140 Last result is equal or above CH[5].LIMIT.HIGH
EVENTS_CH[5].LIMITL 0x144 Last result is equal or below CH[5].LIMIT.LOW
EVENTS_CH[6].LIMITH 0x148 Last result is equal or above CH[6].LIMIT.HIGH
EVENTS_CH[6].LIMITL 0x14C Last result is equal or below CH[6].LIMIT.LOW
EVENTS_CH[7].LIMITH 0x150 Last result is equal or above CH[7].LIMIT.HIGH
EVENTS_CH[7].LIMITL 0x154 Last result is equal or below CH[7].LIMIT.LOW
INTEN 0x300 Enable or disable interrupt
INTENSET 0x304 Enable interrupt
INTENCLR 0x308 Disable interrupt
STATUS 0x400 Status
ENABLE 0x500 Enable or disable SAADC
CH[0].PSELP 0x510 Input positive pin selection for CH[0]
CH[0].PSELN 0x514 Input negative pin selection for CH[0]
CH[0].CONFIG 0x518 Input configuration for CH[0]
CH[0].LIMIT 0x51C High/low limits for event monitoring of a channel
CH[1].PSELP 0x520 Input positive pin selection for CH[1]
CH[1].PSELN 0x524 Input negative pin selection for CH[1]
CH[1].CONFIG 0x528 Input configuration for CH[1]
CH[1].LIMIT 0x52C High/low limits for event monitoring of a channel
CH[2].PSELP 0x530 Input positive pin selection for CH[2]
CH[2].PSELN 0x534 Input negative pin selection for CH[2]
CH[2].CONFIG 0x538 Input configuration for CH[2]
CH[2].LIMIT 0x53C High/low limits for event monitoring of a channel
CH[3].PSELP 0x540 Input positive pin selection for CH[3]
CH[3].PSELN 0x544 Input negative pin selection for CH[3]
CH[3].CONFIG 0x548 Input configuration for CH[3]
CH[3].LIMIT 0x54C High/low limits for event monitoring of a channel
CH[4].PSELP 0x550 Input positive pin selection for CH[4]
CH[4].PSELN 0x554 Input negative pin selection for CH[4]
CH[4].CONFIG 0x558 Input configuration for CH[4]
CH[4].LIMIT 0x55C High/low limits for event monitoring of a channel
CH[5].PSELP 0x560 Input positive pin selection for CH[5]
CH[5].PSELN 0x564 Input negative pin selection for CH[5]
CH[5].CONFIG 0x568 Input configuration for CH[5]
CH[5].LIMIT 0x56C High/low limits for event monitoring of a channel
CH[6].PSELP 0x570 Input positive pin selection for CH[6]
CH[6].PSELN 0x574 Input negative pin selection for CH[6]

4413_417 v1.9 601

 Peripherals

Register Offset Description

CH[6].CONFIG 0x578 Input configuration for CH[6]
CH[6].LIMIT 0x57C High/low limits for event monitoring of a channel
CH[7].PSELP 0x580 Input positive pin selection for CH[7]
CH[7].PSELN 0x584 Input negative pin selection for CH[7]
CH[7].CONFIG 0x588 Input configuration for CH[7]
CH[7].LIMIT 0x58C High/low limits for event monitoring of a channel
RESOLUTION 0x5F0 Resolution configuration
OVERSAMPLE 0x5F4 Oversampling configuration. The RESOLUTION is applied before averaging, thus for high
OVERSAMPLE a higher RESOLUTION should be used.
SAMPLERATE 0x5F8 Controls normal or continuous sample rate
RESULT.PTR 0x62C Data pointer
RESULT.MAXCNT 0x630 Maximum number of 16-bit samples to be written to output RAM buffer
RESULT.AMOUNT 0x634 Number of 16-bit samples written to output RAM buffer since the previous START task

6.23.7.1 TASKS_START
Address offset: 0x000
Starts the SAADC and prepares the result buffer in RAM

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_START Starts the SAADC and prepares the result buffer in RAM
Trigger 1 Trigger task

6.23.7.2 TASKS_SAMPLE
Address offset: 0x004
Takes one SAADC sample

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_SAMPLE Takes one SAADC sample
Trigger 1 Trigger task

6.23.7.3 TASKS_STOP
Address offset: 0x008
Stops the SAADC and terminates all on-going conversions

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STOP Stops the SAADC and terminates all on-going conversions
Trigger 1 Trigger task

4413_417 v1.9 602

 Peripherals

6.23.7.4 TASKS_CALIBRATEOFFSET
Address offset: 0x00C
Starts offset auto-calibration

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_CALIBRATEOFFSET Starts offset auto-calibration
Trigger 1 Trigger task

6.23.7.5 EVENTS_STARTED
Address offset: 0x100
The SAADC has started

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_STARTED The SAADC has started
NotGenerated 0 Event not generated
Generated 1 Event generated

6.23.7.6 EVENTS_END
Address offset: 0x104
The SAADC has filled up the result buffer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_END The SAADC has filled up the result buffer
NotGenerated 0 Event not generated
Generated 1 Event generated

6.23.7.7 EVENTS_DONE
Address offset: 0x108
A conversion task has been completed. Depending on the configuration, multiple conversions might be
needed for a result to be transferred to RAM.

4413_417 v1.9 603

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_DONE A conversion task has been completed. Depending on the configuration,
multiple conversions might be needed for a result to be transferred to RAM.
NotGenerated 0 Event not generated
Generated 1 Event generated

6.23.7.8 EVENTS_RESULTDONE
Address offset: 0x10C
Result ready for transfer to RAM

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_RESULTDONE Result ready for transfer to RAM
NotGenerated 0 Event not generated
Generated 1 Event generated

6.23.7.9 EVENTS_CALIBRATEDONE
Address offset: 0x110
Calibration is complete

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_CALIBRATEDONE Calibration is complete
NotGenerated 0 Event not generated
Generated 1 Event generated

6.23.7.10 EVENTS_STOPPED
Address offset: 0x114
The SAADC has stopped

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_STOPPED The SAADC has stopped
NotGenerated 0 Event not generated
Generated 1 Event generated

6.23.7.11 EVENTS_CH[0]
Peripheral events.

4413_417 v1.9 604

 Peripherals

6.23.7.11.1 EVENTS_CH[0].LIMITH
Address offset: 0x118
Last result is equal or above CH[0].LIMIT.HIGH

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW LIMITH Last result is equal or above CH[0].LIMIT.HIGH
NotGenerated 0 Event not generated
Generated 1 Event generated

6.23.7.11.2 EVENTS_CH[0].LIMITL
Address offset: 0x11C
Last result is equal or below CH[0].LIMIT.LOW

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW LIMITL Last result is equal or below CH[0].LIMIT.LOW
NotGenerated 0 Event not generated
Generated 1 Event generated

6.23.7.12 EVENTS_CH[1]
Peripheral events.

6.23.7.12.1 EVENTS_CH[1].LIMITH
Address offset: 0x120
Last result is equal or above CH[1].LIMIT.HIGH

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW LIMITH Last result is equal or above CH[1].LIMIT.HIGH
NotGenerated 0 Event not generated
Generated 1 Event generated

6.23.7.12.2 EVENTS_CH[1].LIMITL
Address offset: 0x124
Last result is equal or below CH[1].LIMIT.LOW

4413_417 v1.9 605

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW LIMITL Last result is equal or below CH[1].LIMIT.LOW
NotGenerated 0 Event not generated
Generated 1 Event generated

6.23.7.13 EVENTS_CH[2]
Peripheral events.

6.23.7.13.1 EVENTS_CH[2].LIMITH
Address offset: 0x128
Last result is equal or above CH[2].LIMIT.HIGH

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW LIMITH Last result is equal or above CH[2].LIMIT.HIGH
NotGenerated 0 Event not generated
Generated 1 Event generated

6.23.7.13.2 EVENTS_CH[2].LIMITL
Address offset: 0x12C
Last result is equal or below CH[2].LIMIT.LOW

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW LIMITL Last result is equal or below CH[2].LIMIT.LOW
NotGenerated 0 Event not generated
Generated 1 Event generated

6.23.7.14 EVENTS_CH[3]
Peripheral events.

6.23.7.14.1 EVENTS_CH[3].LIMITH
Address offset: 0x130
Last result is equal or above CH[3].LIMIT.HIGH

4413_417 v1.9 606

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW LIMITH Last result is equal or above CH[3].LIMIT.HIGH
NotGenerated 0 Event not generated
Generated 1 Event generated

6.23.7.14.2 EVENTS_CH[3].LIMITL
Address offset: 0x134
Last result is equal or below CH[3].LIMIT.LOW

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW LIMITL Last result is equal or below CH[3].LIMIT.LOW
NotGenerated 0 Event not generated
Generated 1 Event generated

6.23.7.15 EVENTS_CH[4]
Peripheral events.

6.23.7.15.1 EVENTS_CH[4].LIMITH
Address offset: 0x138
Last result is equal or above CH[4].LIMIT.HIGH

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW LIMITH Last result is equal or above CH[4].LIMIT.HIGH
NotGenerated 0 Event not generated
Generated 1 Event generated

6.23.7.15.2 EVENTS_CH[4].LIMITL
Address offset: 0x13C
Last result is equal or below CH[4].LIMIT.LOW

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW LIMITL Last result is equal or below CH[4].LIMIT.LOW
NotGenerated 0 Event not generated
Generated 1 Event generated

4413_417 v1.9 607

 Peripherals

6.23.7.16 EVENTS_CH[5]
Peripheral events.

6.23.7.16.1 EVENTS_CH[5].LIMITH
Address offset: 0x140
Last result is equal or above CH[5].LIMIT.HIGH

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW LIMITH Last result is equal or above CH[5].LIMIT.HIGH
NotGenerated 0 Event not generated
Generated 1 Event generated

6.23.7.16.2 EVENTS_CH[5].LIMITL
Address offset: 0x144
Last result is equal or below CH[5].LIMIT.LOW

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW LIMITL Last result is equal or below CH[5].LIMIT.LOW
NotGenerated 0 Event not generated
Generated 1 Event generated

6.23.7.17 EVENTS_CH[6]
Peripheral events.

6.23.7.17.1 EVENTS_CH[6].LIMITH
Address offset: 0x148
Last result is equal or above CH[6].LIMIT.HIGH

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW LIMITH Last result is equal or above CH[6].LIMIT.HIGH
NotGenerated 0 Event not generated
Generated 1 Event generated

6.23.7.17.2 EVENTS_CH[6].LIMITL
Address offset: 0x14C
Last result is equal or below CH[6].LIMIT.LOW

4413_417 v1.9 608

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW LIMITL Last result is equal or below CH[6].LIMIT.LOW
NotGenerated 0 Event not generated
Generated 1 Event generated

6.23.7.18 EVENTS_CH[7]
Peripheral events.

6.23.7.18.1 EVENTS_CH[7].LIMITH
Address offset: 0x150
Last result is equal or above CH[7].LIMIT.HIGH

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW LIMITH Last result is equal or above CH[7].LIMIT.HIGH
NotGenerated 0 Event not generated
Generated 1 Event generated

6.23.7.18.2 EVENTS_CH[7].LIMITL
Address offset: 0x154
Last result is equal or below CH[7].LIMIT.LOW

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW LIMITL Last result is equal or below CH[7].LIMIT.LOW
NotGenerated 0 Event not generated
Generated 1 Event generated

6.23.7.19 INTEN
Address offset: 0x300
Enable or disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW STARTED Enable or disable interrupt for event STARTED
Disabled 0 Disable
Enabled 1 Enable
B RW END Enable or disable interrupt for event END
Disabled 0 Disable

4413_417 v1.9 609

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Enabled 1 Enable
C RW DONE Enable or disable interrupt for event DONE
Disabled 0 Disable
Enabled 1 Enable
D RW RESULTDONE Enable or disable interrupt for event RESULTDONE
Disabled 0 Disable
Enabled 1 Enable
E RW CALIBRATEDONE Enable or disable interrupt for event CALIBRATEDONE
Disabled 0 Disable
Enabled 1 Enable
F RW STOPPED Enable or disable interrupt for event STOPPED
Disabled 0 Disable
Enabled 1 Enable
G RW CH0LIMITH Enable or disable interrupt for event CH0LIMITH
Disabled 0 Disable
Enabled 1 Enable
H RW CH0LIMITL Enable or disable interrupt for event CH0LIMITL
Disabled 0 Disable
Enabled 1 Enable
I RW CH1LIMITH Enable or disable interrupt for event CH1LIMITH
Disabled 0 Disable
Enabled 1 Enable
J RW CH1LIMITL Enable or disable interrupt for event CH1LIMITL
Disabled 0 Disable
Enabled 1 Enable
K RW CH2LIMITH Enable or disable interrupt for event CH2LIMITH
Disabled 0 Disable
Enabled 1 Enable
L RW CH2LIMITL Enable or disable interrupt for event CH2LIMITL
Disabled 0 Disable
Enabled 1 Enable
M RW CH3LIMITH Enable or disable interrupt for event CH3LIMITH
Disabled 0 Disable
Enabled 1 Enable
N RW CH3LIMITL Enable or disable interrupt for event CH3LIMITL
Disabled 0 Disable
Enabled 1 Enable
O RW CH4LIMITH Enable or disable interrupt for event CH4LIMITH
Disabled 0 Disable
Enabled 1 Enable
P RW CH4LIMITL Enable or disable interrupt for event CH4LIMITL
Disabled 0 Disable
Enabled 1 Enable
Q RW CH5LIMITH Enable or disable interrupt for event CH5LIMITH
Disabled 0 Disable
Enabled 1 Enable
R RW CH5LIMITL Enable or disable interrupt for event CH5LIMITL
Disabled 0 Disable
Enabled 1 Enable
S RW CH6LIMITH Enable or disable interrupt for event CH6LIMITH

4413_417 v1.9 610

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Disabled 0 Disable
Enabled 1 Enable
T RW CH6LIMITL Enable or disable interrupt for event CH6LIMITL
Disabled 0 Disable
Enabled 1 Enable
U RW CH7LIMITH Enable or disable interrupt for event CH7LIMITH
Disabled 0 Disable
Enabled 1 Enable
V RW CH7LIMITL Enable or disable interrupt for event CH7LIMITL
Disabled 0 Disable
Enabled 1 Enable

6.23.7.20 INTENSET
Address offset: 0x304
Enable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW STARTED Write '1' to enable interrupt for event STARTED
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW END Write '1' to enable interrupt for event END
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW DONE Write '1' to enable interrupt for event DONE
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
D RW RESULTDONE Write '1' to enable interrupt for event RESULTDONE
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
E RW CALIBRATEDONE Write '1' to enable interrupt for event CALIBRATEDONE
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
F RW STOPPED Write '1' to enable interrupt for event STOPPED
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
G RW CH0LIMITH Write '1' to enable interrupt for event CH0LIMITH
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

4413_417 v1.9 611

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
H RW CH0LIMITL Write '1' to enable interrupt for event CH0LIMITL
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
I RW CH1LIMITH Write '1' to enable interrupt for event CH1LIMITH
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
J RW CH1LIMITL Write '1' to enable interrupt for event CH1LIMITL
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
K RW CH2LIMITH Write '1' to enable interrupt for event CH2LIMITH
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
L RW CH2LIMITL Write '1' to enable interrupt for event CH2LIMITL
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
M RW CH3LIMITH Write '1' to enable interrupt for event CH3LIMITH
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
N RW CH3LIMITL Write '1' to enable interrupt for event CH3LIMITL
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
O RW CH4LIMITH Write '1' to enable interrupt for event CH4LIMITH
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
P RW CH4LIMITL Write '1' to enable interrupt for event CH4LIMITL
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
Q RW CH5LIMITH Write '1' to enable interrupt for event CH5LIMITH
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
R RW CH5LIMITL Write '1' to enable interrupt for event CH5LIMITL
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
S RW CH6LIMITH Write '1' to enable interrupt for event CH6LIMITH
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
T RW CH6LIMITL Write '1' to enable interrupt for event CH6LIMITL
Set 1 Enable

4413_417 v1.9 612

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
U RW CH7LIMITH Write '1' to enable interrupt for event CH7LIMITH
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
V RW CH7LIMITL Write '1' to enable interrupt for event CH7LIMITL
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.23.7.21 INTENCLR
Address offset: 0x308
Disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW STARTED Write '1' to disable interrupt for event STARTED
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW END Write '1' to disable interrupt for event END
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW DONE Write '1' to disable interrupt for event DONE
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
D RW RESULTDONE Write '1' to disable interrupt for event RESULTDONE
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
E RW CALIBRATEDONE Write '1' to disable interrupt for event CALIBRATEDONE
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
F RW STOPPED Write '1' to disable interrupt for event STOPPED
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
G RW CH0LIMITH Write '1' to disable interrupt for event CH0LIMITH
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
H RW CH0LIMITL Write '1' to disable interrupt for event CH0LIMITL

4413_417 v1.9 613

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
I RW CH1LIMITH Write '1' to disable interrupt for event CH1LIMITH
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
J RW CH1LIMITL Write '1' to disable interrupt for event CH1LIMITL
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
K RW CH2LIMITH Write '1' to disable interrupt for event CH2LIMITH
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
L RW CH2LIMITL Write '1' to disable interrupt for event CH2LIMITL
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
M RW CH3LIMITH Write '1' to disable interrupt for event CH3LIMITH
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
N RW CH3LIMITL Write '1' to disable interrupt for event CH3LIMITL
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
O RW CH4LIMITH Write '1' to disable interrupt for event CH4LIMITH
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
P RW CH4LIMITL Write '1' to disable interrupt for event CH4LIMITL
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
Q RW CH5LIMITH Write '1' to disable interrupt for event CH5LIMITH
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
R RW CH5LIMITL Write '1' to disable interrupt for event CH5LIMITL
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
S RW CH6LIMITH Write '1' to disable interrupt for event CH6LIMITH
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
T RW CH6LIMITL Write '1' to disable interrupt for event CH6LIMITL
Clear 1 Disable
Disabled 0 Read: Disabled

4413_417 v1.9 614

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Enabled 1 Read: Enabled
U RW CH7LIMITH Write '1' to disable interrupt for event CH7LIMITH
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
V RW CH7LIMITL Write '1' to disable interrupt for event CH7LIMITL
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.23.7.22 STATUS
Address offset: 0x400
Status

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R STATUS Status
Ready 0 SAADC is ready. No on-going conversions.
Busy 1 SAADC is busy. Conversion in progress.

6.23.7.23 ENABLE
Address offset: 0x500
Enable or disable SAADC

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW ENABLE Enable or disable SAADC
Disabled 0 Disable SAADC
Enabled 1 Enable SAADC

When enabled, the SAADC will acquire access to analog input pins specified
in registers CH[n].PSELP and CH[n].PSELN

6.23.7.24 CH[0].PSELP
Address offset: 0x510
Input positive pin selection for CH[0]

4413_417 v1.9 615

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PSELP Analog positive input channel
NC 0 Not connected
AnalogInput0 1 AIN0
AnalogInput1 2 AIN1
AnalogInput2 3 AIN2
AnalogInput3 4 AIN3
AnalogInput4 5 AIN4
AnalogInput5 6 AIN5
AnalogInput6 7 AIN6
AnalogInput7 8 AIN7
VDD 9 VDD
VDDHDIV5 0x0D VDDH/5

6.23.7.25 CH[0].PSELN
Address offset: 0x514
Input negative pin selection for CH[0]

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PSELN Analog negative input, enables differential channel
NC 0 Not connected
AnalogInput0 1 AIN0
AnalogInput1 2 AIN1
AnalogInput2 3 AIN2
AnalogInput3 4 AIN3
AnalogInput4 5 AIN4
AnalogInput5 6 AIN5
AnalogInput6 7 AIN6
AnalogInput7 8 AIN7
VDD 9 VDD
VDDHDIV5 0x0D VDDH/5

6.23.7.26 CH[0].CONFIG
Address offset: 0x518
Input configuration for CH[0]

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID G F E E E D C C C B B A A

Reset 0x00020000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW RESP Positive channel resistor control
Bypass 0 Bypass resistor ladder
Pulldown 1 Pull-down to GND
Pullup 2 Pull-up to VDD
VDD1_2 3 Set input at VDD/2

4413_417 v1.9 616

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID G F E E E D C C C B B A A

Reset 0x00020000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
B RW RESN Negative channel resistor control
Bypass 0 Bypass resistor ladder
Pulldown 1 Pull-down to GND
Pullup 2 Pull-up to VDD
VDD1_2 3 Set input at VDD/2
C RW GAIN Gain control
Gain1_6 0 1/6
Gain1_5 1 1/5
Gain1_4 2 1/4
Gain1_3 3 1/3
Gain1_2 4 1/2
Gain1 5 1
Gain2 6 2
Gain4 7 4
D- RW REFSEL Reference control
Internal 0 Internal reference (0.6 V)
VDD1_4 1 VDD/4 as reference
E RW TACQ Acquisition time, the time the SAADC uses to sample the input voltage
3us 0 3 µs
5us 1 5 µs
10us 2 10 µs
15us 3 15 µs
20us 4 20 µs
40us 5 40 µs
F RW MODE Enable differential mode
SE 0 Single-ended, PSELN will be ignored, negative input to SAADC shorted to
GND
Diff 1 Differential
G RW BURST Enable burst mode
Disabled 0 Burst mode is disabled (normal operation)
Enabled 1 Burst mode is enabled. SAADC takes 2^OVERSAMPLE number of samples as
fast as it can, and sends the average to Data RAM.

6.23.7.27 CH[0].LIMIT
Address offset: 0x51C
High/low limits for event monitoring of a channel

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B B B B B B B B B B B B B B B B A A A A A A A A A A A A A A A A

Reset 0x7FFF8000 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW LOW [-32768 to +32767] Low level limit
B RW HIGH [-32768 to +32767] High level limit

6.23.7.28 CH[1].PSELP
Address offset: 0x520
Input positive pin selection for CH[1]

4413_417 v1.9 617

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PSELP Analog positive input channel
NC 0 Not connected
AnalogInput0 1 AIN0
AnalogInput1 2 AIN1
AnalogInput2 3 AIN2
AnalogInput3 4 AIN3
AnalogInput4 5 AIN4
AnalogInput5 6 AIN5
AnalogInput6 7 AIN6
AnalogInput7 8 AIN7
VDD 9 VDD
VDDHDIV5 0x0D VDDH/5

6.23.7.29 CH[1].PSELN
Address offset: 0x524
Input negative pin selection for CH[1]

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PSELN Analog negative input, enables differential channel
NC 0 Not connected
AnalogInput0 1 AIN0
AnalogInput1 2 AIN1
AnalogInput2 3 AIN2
AnalogInput3 4 AIN3
AnalogInput4 5 AIN4
AnalogInput5 6 AIN5
AnalogInput6 7 AIN6
AnalogInput7 8 AIN7
VDD 9 VDD
VDDHDIV5 0x0D VDDH/5

6.23.7.30 CH[1].CONFIG
Address offset: 0x528
Input configuration for CH[1]

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID G F E E E D C C C B B A A

Reset 0x00020000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW RESP Positive channel resistor control
Bypass 0 Bypass resistor ladder
Pulldown 1 Pull-down to GND
Pullup 2 Pull-up to VDD
VDD1_2 3 Set input at VDD/2

4413_417 v1.9 618

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID G F E E E D C C C B B A A

Reset 0x00020000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
B RW RESN Negative channel resistor control
Bypass 0 Bypass resistor ladder
Pulldown 1 Pull-down to GND
Pullup 2 Pull-up to VDD
VDD1_2 3 Set input at VDD/2
C RW GAIN Gain control
Gain1_6 0 1/6
Gain1_5 1 1/5
Gain1_4 2 1/4
Gain1_3 3 1/3
Gain1_2 4 1/2
Gain1 5 1
Gain2 6 2
Gain4 7 4
D- RW REFSEL Reference control
Internal 0 Internal reference (0.6 V)
VDD1_4 1 VDD/4 as reference
E RW TACQ Acquisition time, the time the SAADC uses to sample the input voltage
3us 0 3 µs
5us 1 5 µs
10us 2 10 µs
15us 3 15 µs
20us 4 20 µs
40us 5 40 µs
F RW MODE Enable differential mode
SE 0 Single-ended, PSELN will be ignored, negative input to SAADC shorted to
GND
Diff 1 Differential
G RW BURST Enable burst mode
Disabled 0 Burst mode is disabled (normal operation)
Enabled 1 Burst mode is enabled. SAADC takes 2^OVERSAMPLE number of samples as
fast as it can, and sends the average to Data RAM.

6.23.7.31 CH[1].LIMIT
Address offset: 0x52C
High/low limits for event monitoring of a channel

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B B B B B B B B B B B B B B B B A A A A A A A A A A A A A A A A

Reset 0x7FFF8000 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW LOW [-32768 to +32767] Low level limit
B RW HIGH [-32768 to +32767] High level limit

6.23.7.32 CH[2].PSELP
Address offset: 0x530
Input positive pin selection for CH[2]

4413_417 v1.9 619

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PSELP Analog positive input channel
NC 0 Not connected
AnalogInput0 1 AIN0
AnalogInput1 2 AIN1
AnalogInput2 3 AIN2
AnalogInput3 4 AIN3
AnalogInput4 5 AIN4
AnalogInput5 6 AIN5
AnalogInput6 7 AIN6
AnalogInput7 8 AIN7
VDD 9 VDD
VDDHDIV5 0x0D VDDH/5

6.23.7.33 CH[2].PSELN
Address offset: 0x534
Input negative pin selection for CH[2]

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PSELN Analog negative input, enables differential channel
NC 0 Not connected
AnalogInput0 1 AIN0
AnalogInput1 2 AIN1
AnalogInput2 3 AIN2
AnalogInput3 4 AIN3
AnalogInput4 5 AIN4
AnalogInput5 6 AIN5
AnalogInput6 7 AIN6
AnalogInput7 8 AIN7
VDD 9 VDD
VDDHDIV5 0x0D VDDH/5

6.23.7.34 CH[2].CONFIG
Address offset: 0x538
Input configuration for CH[2]

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID G F E E E D C C C B B A A

Reset 0x00020000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW RESP Positive channel resistor control
Bypass 0 Bypass resistor ladder
Pulldown 1 Pull-down to GND
Pullup 2 Pull-up to VDD
VDD1_2 3 Set input at VDD/2

4413_417 v1.9 620

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID G F E E E D C C C B B A A

Reset 0x00020000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
B RW RESN Negative channel resistor control
Bypass 0 Bypass resistor ladder
Pulldown 1 Pull-down to GND
Pullup 2 Pull-up to VDD
VDD1_2 3 Set input at VDD/2
C RW GAIN Gain control
Gain1_6 0 1/6
Gain1_5 1 1/5
Gain1_4 2 1/4
Gain1_3 3 1/3
Gain1_2 4 1/2
Gain1 5 1
Gain2 6 2
Gain4 7 4
D- RW REFSEL Reference control
Internal 0 Internal reference (0.6 V)
VDD1_4 1 VDD/4 as reference
E RW TACQ Acquisition time, the time the SAADC uses to sample the input voltage
3us 0 3 µs
5us 1 5 µs
10us 2 10 µs
15us 3 15 µs
20us 4 20 µs
40us 5 40 µs
F RW MODE Enable differential mode
SE 0 Single-ended, PSELN will be ignored, negative input to SAADC shorted to
GND
Diff 1 Differential
G RW BURST Enable burst mode
Disabled 0 Burst mode is disabled (normal operation)
Enabled 1 Burst mode is enabled. SAADC takes 2^OVERSAMPLE number of samples as
fast as it can, and sends the average to Data RAM.

6.23.7.35 CH[2].LIMIT
Address offset: 0x53C
High/low limits for event monitoring of a channel

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B B B B B B B B B B B B B B B B A A A A A A A A A A A A A A A A

Reset 0x7FFF8000 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW LOW [-32768 to +32767] Low level limit
B RW HIGH [-32768 to +32767] High level limit

6.23.7.36 CH[3].PSELP
Address offset: 0x540
Input positive pin selection for CH[3]

4413_417 v1.9 621

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PSELP Analog positive input channel
NC 0 Not connected
AnalogInput0 1 AIN0
AnalogInput1 2 AIN1
AnalogInput2 3 AIN2
AnalogInput3 4 AIN3
AnalogInput4 5 AIN4
AnalogInput5 6 AIN5
AnalogInput6 7 AIN6
AnalogInput7 8 AIN7
VDD 9 VDD
VDDHDIV5 0x0D VDDH/5

6.23.7.37 CH[3].PSELN
Address offset: 0x544
Input negative pin selection for CH[3]

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PSELN Analog negative input, enables differential channel
NC 0 Not connected
AnalogInput0 1 AIN0
AnalogInput1 2 AIN1
AnalogInput2 3 AIN2
AnalogInput3 4 AIN3
AnalogInput4 5 AIN4
AnalogInput5 6 AIN5
AnalogInput6 7 AIN6
AnalogInput7 8 AIN7
VDD 9 VDD
VDDHDIV5 0x0D VDDH/5

6.23.7.38 CH[3].CONFIG
Address offset: 0x548
Input configuration for CH[3]

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID G F E E E D C C C B B A A

Reset 0x00020000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW RESP Positive channel resistor control
Bypass 0 Bypass resistor ladder
Pulldown 1 Pull-down to GND
Pullup 2 Pull-up to VDD
VDD1_2 3 Set input at VDD/2

4413_417 v1.9 622

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID G F E E E D C C C B B A A

Reset 0x00020000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
B RW RESN Negative channel resistor control
Bypass 0 Bypass resistor ladder
Pulldown 1 Pull-down to GND
Pullup 2 Pull-up to VDD
VDD1_2 3 Set input at VDD/2
C RW GAIN Gain control
Gain1_6 0 1/6
Gain1_5 1 1/5
Gain1_4 2 1/4
Gain1_3 3 1/3
Gain1_2 4 1/2
Gain1 5 1
Gain2 6 2
Gain4 7 4
D- RW REFSEL Reference control
Internal 0 Internal reference (0.6 V)
VDD1_4 1 VDD/4 as reference
E RW TACQ Acquisition time, the time the SAADC uses to sample the input voltage
3us 0 3 µs
5us 1 5 µs
10us 2 10 µs
15us 3 15 µs
20us 4 20 µs
40us 5 40 µs
F RW MODE Enable differential mode
SE 0 Single-ended, PSELN will be ignored, negative input to SAADC shorted to
GND
Diff 1 Differential
G RW BURST Enable burst mode
Disabled 0 Burst mode is disabled (normal operation)
Enabled 1 Burst mode is enabled. SAADC takes 2^OVERSAMPLE number of samples as
fast as it can, and sends the average to Data RAM.

6.23.7.39 CH[3].LIMIT
Address offset: 0x54C
High/low limits for event monitoring of a channel

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B B B B B B B B B B B B B B B B A A A A A A A A A A A A A A A A

Reset 0x7FFF8000 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW LOW [-32768 to +32767] Low level limit
B RW HIGH [-32768 to +32767] High level limit

6.23.7.40 CH[4].PSELP
Address offset: 0x550
Input positive pin selection for CH[4]

4413_417 v1.9 623

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PSELP Analog positive input channel
NC 0 Not connected
AnalogInput0 1 AIN0
AnalogInput1 2 AIN1
AnalogInput2 3 AIN2
AnalogInput3 4 AIN3
AnalogInput4 5 AIN4
AnalogInput5 6 AIN5
AnalogInput6 7 AIN6
AnalogInput7 8 AIN7
VDD 9 VDD
VDDHDIV5 0x0D VDDH/5

6.23.7.41 CH[4].PSELN
Address offset: 0x554
Input negative pin selection for CH[4]

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PSELN Analog negative input, enables differential channel
NC 0 Not connected
AnalogInput0 1 AIN0
AnalogInput1 2 AIN1
AnalogInput2 3 AIN2
AnalogInput3 4 AIN3
AnalogInput4 5 AIN4
AnalogInput5 6 AIN5
AnalogInput6 7 AIN6
AnalogInput7 8 AIN7
VDD 9 VDD
VDDHDIV5 0x0D VDDH/5

6.23.7.42 CH[4].CONFIG
Address offset: 0x558
Input configuration for CH[4]

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID G F E E E D C C C B B A A

Reset 0x00020000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW RESP Positive channel resistor control
Bypass 0 Bypass resistor ladder
Pulldown 1 Pull-down to GND
Pullup 2 Pull-up to VDD
VDD1_2 3 Set input at VDD/2

4413_417 v1.9 624

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID G F E E E D C C C B B A A

Reset 0x00020000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
B RW RESN Negative channel resistor control
Bypass 0 Bypass resistor ladder
Pulldown 1 Pull-down to GND
Pullup 2 Pull-up to VDD
VDD1_2 3 Set input at VDD/2
C RW GAIN Gain control
Gain1_6 0 1/6
Gain1_5 1 1/5
Gain1_4 2 1/4
Gain1_3 3 1/3
Gain1_2 4 1/2
Gain1 5 1
Gain2 6 2
Gain4 7 4
D- RW REFSEL Reference control
Internal 0 Internal reference (0.6 V)
VDD1_4 1 VDD/4 as reference
E RW TACQ Acquisition time, the time the SAADC uses to sample the input voltage
3us 0 3 µs
5us 1 5 µs
10us 2 10 µs
15us 3 15 µs
20us 4 20 µs
40us 5 40 µs
F RW MODE Enable differential mode
SE 0 Single-ended, PSELN will be ignored, negative input to SAADC shorted to
GND
Diff 1 Differential
G RW BURST Enable burst mode
Disabled 0 Burst mode is disabled (normal operation)
Enabled 1 Burst mode is enabled. SAADC takes 2^OVERSAMPLE number of samples as
fast as it can, and sends the average to Data RAM.

6.23.7.43 CH[4].LIMIT
Address offset: 0x55C
High/low limits for event monitoring of a channel

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B B B B B B B B B B B B B B B B A A A A A A A A A A A A A A A A

Reset 0x7FFF8000 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW LOW [-32768 to +32767] Low level limit
B RW HIGH [-32768 to +32767] High level limit

6.23.7.44 CH[5].PSELP
Address offset: 0x560
Input positive pin selection for CH[5]

4413_417 v1.9 625

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PSELP Analog positive input channel
NC 0 Not connected
AnalogInput0 1 AIN0
AnalogInput1 2 AIN1
AnalogInput2 3 AIN2
AnalogInput3 4 AIN3
AnalogInput4 5 AIN4
AnalogInput5 6 AIN5
AnalogInput6 7 AIN6
AnalogInput7 8 AIN7
VDD 9 VDD
VDDHDIV5 0x0D VDDH/5

6.23.7.45 CH[5].PSELN
Address offset: 0x564
Input negative pin selection for CH[5]

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PSELN Analog negative input, enables differential channel
NC 0 Not connected
AnalogInput0 1 AIN0
AnalogInput1 2 AIN1
AnalogInput2 3 AIN2
AnalogInput3 4 AIN3
AnalogInput4 5 AIN4
AnalogInput5 6 AIN5
AnalogInput6 7 AIN6
AnalogInput7 8 AIN7
VDD 9 VDD
VDDHDIV5 0x0D VDDH/5

6.23.7.46 CH[5].CONFIG
Address offset: 0x568
Input configuration for CH[5]

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID G F E E E D C C C B B A A

Reset 0x00020000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW RESP Positive channel resistor control
Bypass 0 Bypass resistor ladder
Pulldown 1 Pull-down to GND
Pullup 2 Pull-up to VDD
VDD1_2 3 Set input at VDD/2

4413_417 v1.9 626

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID G F E E E D C C C B B A A

Reset 0x00020000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
B RW RESN Negative channel resistor control
Bypass 0 Bypass resistor ladder
Pulldown 1 Pull-down to GND
Pullup 2 Pull-up to VDD
VDD1_2 3 Set input at VDD/2
C RW GAIN Gain control
Gain1_6 0 1/6
Gain1_5 1 1/5
Gain1_4 2 1/4
Gain1_3 3 1/3
Gain1_2 4 1/2
Gain1 5 1
Gain2 6 2
Gain4 7 4
D- RW REFSEL Reference control
Internal 0 Internal reference (0.6 V)
VDD1_4 1 VDD/4 as reference
E RW TACQ Acquisition time, the time the SAADC uses to sample the input voltage
3us 0 3 µs
5us 1 5 µs
10us 2 10 µs
15us 3 15 µs
20us 4 20 µs
40us 5 40 µs
F RW MODE Enable differential mode
SE 0 Single-ended, PSELN will be ignored, negative input to SAADC shorted to
GND
Diff 1 Differential
G RW BURST Enable burst mode
Disabled 0 Burst mode is disabled (normal operation)
Enabled 1 Burst mode is enabled. SAADC takes 2^OVERSAMPLE number of samples as
fast as it can, and sends the average to Data RAM.

6.23.7.47 CH[5].LIMIT
Address offset: 0x56C
High/low limits for event monitoring of a channel

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B B B B B B B B B B B B B B B B A A A A A A A A A A A A A A A A

Reset 0x7FFF8000 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW LOW [-32768 to +32767] Low level limit
B RW HIGH [-32768 to +32767] High level limit

6.23.7.48 CH[6].PSELP
Address offset: 0x570
Input positive pin selection for CH[6]

4413_417 v1.9 627

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PSELP Analog positive input channel
NC 0 Not connected
AnalogInput0 1 AIN0
AnalogInput1 2 AIN1
AnalogInput2 3 AIN2
AnalogInput3 4 AIN3
AnalogInput4 5 AIN4
AnalogInput5 6 AIN5
AnalogInput6 7 AIN6
AnalogInput7 8 AIN7
VDD 9 VDD
VDDHDIV5 0x0D VDDH/5

6.23.7.49 CH[6].PSELN
Address offset: 0x574
Input negative pin selection for CH[6]

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PSELN Analog negative input, enables differential channel
NC 0 Not connected
AnalogInput0 1 AIN0
AnalogInput1 2 AIN1
AnalogInput2 3 AIN2
AnalogInput3 4 AIN3
AnalogInput4 5 AIN4
AnalogInput5 6 AIN5
AnalogInput6 7 AIN6
AnalogInput7 8 AIN7
VDD 9 VDD
VDDHDIV5 0x0D VDDH/5

6.23.7.50 CH[6].CONFIG
Address offset: 0x578
Input configuration for CH[6]

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID G F E E E D C C C B B A A

Reset 0x00020000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW RESP Positive channel resistor control
Bypass 0 Bypass resistor ladder
Pulldown 1 Pull-down to GND
Pullup 2 Pull-up to VDD
VDD1_2 3 Set input at VDD/2

4413_417 v1.9 628

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID G F E E E D C C C B B A A

Reset 0x00020000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
B RW RESN Negative channel resistor control
Bypass 0 Bypass resistor ladder
Pulldown 1 Pull-down to GND
Pullup 2 Pull-up to VDD
VDD1_2 3 Set input at VDD/2
C RW GAIN Gain control
Gain1_6 0 1/6
Gain1_5 1 1/5
Gain1_4 2 1/4
Gain1_3 3 1/3
Gain1_2 4 1/2
Gain1 5 1
Gain2 6 2
Gain4 7 4
D- RW REFSEL Reference control
Internal 0 Internal reference (0.6 V)
VDD1_4 1 VDD/4 as reference
E RW TACQ Acquisition time, the time the SAADC uses to sample the input voltage
3us 0 3 µs
5us 1 5 µs
10us 2 10 µs
15us 3 15 µs
20us 4 20 µs
40us 5 40 µs
F RW MODE Enable differential mode
SE 0 Single-ended, PSELN will be ignored, negative input to SAADC shorted to
GND
Diff 1 Differential
G RW BURST Enable burst mode
Disabled 0 Burst mode is disabled (normal operation)
Enabled 1 Burst mode is enabled. SAADC takes 2^OVERSAMPLE number of samples as
fast as it can, and sends the average to Data RAM.

6.23.7.51 CH[6].LIMIT
Address offset: 0x57C
High/low limits for event monitoring of a channel

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B B B B B B B B B B B B B B B B A A A A A A A A A A A A A A A A

Reset 0x7FFF8000 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW LOW [-32768 to +32767] Low level limit
B RW HIGH [-32768 to +32767] High level limit

6.23.7.52 CH[7].PSELP
Address offset: 0x580
Input positive pin selection for CH[7]

4413_417 v1.9 629

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PSELP Analog positive input channel
NC 0 Not connected
AnalogInput0 1 AIN0
AnalogInput1 2 AIN1
AnalogInput2 3 AIN2
AnalogInput3 4 AIN3
AnalogInput4 5 AIN4
AnalogInput5 6 AIN5
AnalogInput6 7 AIN6
AnalogInput7 8 AIN7
VDD 9 VDD
VDDHDIV5 0x0D VDDH/5

6.23.7.53 CH[7].PSELN
Address offset: 0x584
Input negative pin selection for CH[7]

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PSELN Analog negative input, enables differential channel
NC 0 Not connected
AnalogInput0 1 AIN0
AnalogInput1 2 AIN1
AnalogInput2 3 AIN2
AnalogInput3 4 AIN3
AnalogInput4 5 AIN4
AnalogInput5 6 AIN5
AnalogInput6 7 AIN6
AnalogInput7 8 AIN7
VDD 9 VDD
VDDHDIV5 0x0D VDDH/5

6.23.7.54 CH[7].CONFIG
Address offset: 0x588
Input configuration for CH[7]

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID G F E E E D C C C B B A A

Reset 0x00020000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW RESP Positive channel resistor control
Bypass 0 Bypass resistor ladder
Pulldown 1 Pull-down to GND
Pullup 2 Pull-up to VDD
VDD1_2 3 Set input at VDD/2

4413_417 v1.9 630

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID G F E E E D C C C B B A A

Reset 0x00020000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
B RW RESN Negative channel resistor control
Bypass 0 Bypass resistor ladder
Pulldown 1 Pull-down to GND
Pullup 2 Pull-up to VDD
VDD1_2 3 Set input at VDD/2
C RW GAIN Gain control
Gain1_6 0 1/6
Gain1_5 1 1/5
Gain1_4 2 1/4
Gain1_3 3 1/3
Gain1_2 4 1/2
Gain1 5 1
Gain2 6 2
Gain4 7 4
D- RW REFSEL Reference control
Internal 0 Internal reference (0.6 V)
VDD1_4 1 VDD/4 as reference
E RW TACQ Acquisition time, the time the SAADC uses to sample the input voltage
3us 0 3 µs
5us 1 5 µs
10us 2 10 µs
15us 3 15 µs
20us 4 20 µs
40us 5 40 µs
F RW MODE Enable differential mode
SE 0 Single-ended, PSELN will be ignored, negative input to SAADC shorted to
GND
Diff 1 Differential
G RW BURST Enable burst mode
Disabled 0 Burst mode is disabled (normal operation)
Enabled 1 Burst mode is enabled. SAADC takes 2^OVERSAMPLE number of samples as
fast as it can, and sends the average to Data RAM.

6.23.7.55 CH[7].LIMIT
Address offset: 0x58C
High/low limits for event monitoring of a channel

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B B B B B B B B B B B B B B B B A A A A A A A A A A A A A A A A

Reset 0x7FFF8000 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW LOW [-32768 to +32767] Low level limit
B RW HIGH [-32768 to +32767] High level limit

6.23.7.56 RESOLUTION
Address offset: 0x5F0
Resolution configuration

4413_417 v1.9 631

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A

Reset 0x00000001 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
ID R/W Field Value ID Value Description
A RW VAL Set the resolution

8bit 0 8 bits
10bit 1 10 bits
12bit 2 12 bits
14bit 3 14 bits

6.23.7.57 OVERSAMPLE
Address offset: 0x5F4
Oversampling configuration. The RESOLUTION is applied before averaging, thus for high OVERSAMPLE a
higher RESOLUTION should be used.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW OVERSAMPLE Oversample control
Bypass 0 Bypass oversampling
Over2x 1 Oversample 2x
Over4x 2 Oversample 4x
Over8x 3 Oversample 8x
Over16x 4 Oversample 16x
Over32x 5 Oversample 32x
Over64x 6 Oversample 64x
Over128x 7 Oversample 128x
Over256x 8 Oversample 256x

6.23.7.58 SAMPLERATE
Address offset: 0x5F8
Controls normal or continuous sample rate

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW CC [80..2047] Capture and compare value. Sample rate is 16 MHz/CC
B RW MODE Select mode for sample rate control
Task 0 Rate is controlled from SAMPLE task
Timers 1 Rate is controlled from local timer (use CC to control the rate)

6.23.7.59 RESULT
RESULT EasyDMA channel

6.23.7.59.1 RESULT.PTR
Address offset: 0x62C
Data pointer

4413_417 v1.9 632

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PTR Data pointer

Note: See Memory on page 21 for details about memories

available to EasyDMA.

6.23.7.59.2 RESULT.MAXCNT
Address offset: 0x630
Maximum number of 16-bit samples to be written to output RAM buffer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW MAXCNT Maximum number of 16-bit samples to be written to output RAM buffer

6.23.7.59.3 RESULT.AMOUNT
Address offset: 0x634
Number of 16-bit samples written to output RAM buffer since the previous START task

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R AMOUNT Number of 16-bit samples written to output RAM buffer since the previous
START task. This register can be read after an END or STOPPED event.

6.23.8 Electrical specification

6.23.8.1 SAADC electrical specification

Symbol Description Min. Typ. Max. Units

DNL10 Differential non-linearity, 10-bit resolution -0.95 <1 LSB10b
INL10 Integral non-linearity, 10-bit resolution 1 LSB10b
DNL12 Differential non-linearity, 12-bit resolution -0.95 1.3 LSB12b
INL12 Integral non-linearity, 12-bit resolution 4.7 LSB12b
VOS Differential offset error (calibrated), 10-bit resolution 27 ±2 LSB10b

EVDDHDIV5 Error on VDDHDIV5 input ±1 %

CEG Gain error temperature coefficient 0.02 %/◦C
fSAMPLE Maximum sampling rate 200 kHz
tCONV Conversion time <2 µs
EG1/6 28
Error for gain = 1/6 -3 3 %

EG1/4 Error28 for gain = 1/4 -3 3 %

27
Digital output code at zero volt differential input.
28
Does not include temperature drift

4413_417 v1.9 633

 Peripherals

Symbol Description Min. Typ. Max. Units

EG1/2 28
Error for gain = 1/2 -3 4 %

EG1 28
Error for gain = 1 -3 4 %

CSAMPLE Sample and hold capacitance at maximum gain29 2.5 pF

RINPUT Input resistance >1 MΩ

ENOB Effective number of bits, differential mode, 12-bit resolution, 1/1 gain, 3 µs 9 Bit
acquisition time, crystal HFCLK, 200 ksps
SNDR Peak signal to noise and distortion ratio, differential mode, 12-bit resolution, 56 dB
1/1 gain, 3 µs acquisition time, crystal HFCLK, 200 ksps
SFDR Spurious free dynamic range, differential mode, 12-bit resolution, 1/1 gain, 3 70 dBc
µs acquisition time, crystal HFCLK, 200 ksps
RLADDER Ladder resistance 160 kΩ

6.24 SPI — Serial peripheral interface master

The SPI master provides a simple CPU interface which includes a TXD register for sending data and an RXD
register for receiving data. This section is added for legacy support for now.
PSEL.MISO PSEL.SCK PSEL.MOSI

RXD-1 TXD+1
MISO MOSI

RXD TXD

READY

Figure 155: SPI master

RXD-1 and TXD+1 illustrate the double buffered version of RXD and TXD respectively.

6.24.1 Functional description

The TXD and RXD registers are double-buffered to enable some degree of uninterrupted data flow in and
out of the SPI master.
The SPI master does not implement support for chip select directly. Therefore, the CPU must use available
GPIOs to select the correct slave and control this independently of the SPI master. The SPI master supports
SPI modes 0 through 3.

29
Maximum gain corresponds to highest capacitance.

4413_417 v1.9 634

 Peripherals

Mode Clock polarity Clock phase

CPOL CPHA
SPI_MODE0 0 (Leading) 0 (Active high)
SPI_MODE1 0 (Leading) 1 (Active low)
SPI_MODE2 1 (Trailing) 0 (Active high)
SPI_MODE3 1 (Trailing) 1 (Active low)

Table 42: SPI modes

6.24.1.1 SPI master mode pin configuration

The different signals SCK, MOSI, and MISO associated with the SPI master are mapped to physical pins.
This mapping is according to the configuration specified in the PSEL.SCK, PSEL.MOSI, and PSEL.MISO
registers respectively. If the CONNECT field of a PSEL.xxx register is set to Disconnected, the associated SPI
master signal is not connected to any physical pin. The PSEL.SCK, PSEL.MOSI, and PSEL.MISO registers and
their configurations are only used as long as the SPI master is enabled, and retained only as long as the
device is in ON mode. PSEL.SCK, PSEL.MOSI, and PSEL.MISO must only be configured when the SPI master
is disabled.
To secure correct behavior in the SPI, the pins used by the SPI must be configured in the GPIO peripheral
as described in GPIO configuration on page 635 prior to enabling the SPI. The SCK must always be
connected to a pin, and that pin's input buffer must always be connected for the SPI to work. This
configuration must be retained in the GPIO for the selected I/Os as long as the SPI is enabled.
Only one peripheral can be assigned to drive a particular GPIO pin at a time. Failing to do so may result in
unpredictable behavior.

SPI master signal SPI master pin Direction Output value

SCK As specified in PSEL.SCK Output Same as CONFIG.CPOL
MOSI As specified in PSEL.MOSI Output 0
MISO As specified in PSEL.MISO Input Not applicable

Table 43: GPIO configuration

6.24.1.2 Shared resources

The SPI shares registers and other resources with other peripherals that have the same ID as the SPI.
Therefore, the user must disable all peripherals that have the same ID as the SPI before the SPI can be
configured and used.
Disabling a peripheral that has the same ID as the SPI will not reset any of the registers that are shared
with the SPI. It is therefore important to configure all relevant SPI registers explicitly to secure that it
operates correctly.
See the Instantiation table in Instantiation on page 24 for details on peripherals and their IDs.

6.24.1.3 SPI master transaction sequence

An SPI master transaction is started by writing the first byte, which is to be transmitted by the SPI master,
to the TXD register.
Since the transmitter is double buffered, the second byte can be written to the TXD register immediately
after the first one. The SPI master will then send these bytes in the order they are written to the TXD
register.
The SPI master is a synchronous interface, and for every byte that is sent, a different byte will be received
at the same time. This is illustrated in SPI master transaction on page 636. Bytes that are received will
be moved to the RXD register where the CPU can extract them by reading the register. The RXD register is
double buffered in the same way as the TXD register, and a second byte can therefore be received at the

4413_417 v1.9 635

 Peripherals

same time as the first byte is being extracted from RXD by the CPU. The SPI master will generate a READY
event every time a new byte is moved to the RXD register. The double buffered byte will be moved from
RXD-1 to RXD as soon as the first byte is extracted from RXD. The SPI master will stop when there are no
more bytes to send in TXD and TXD+1.

CSN

SCK

MOSI 0 1 2 n-2 n-1 n

MISO A B C m-2 m-1 m

READY

READY

READY

READY

READY

READY
CPU 1 2 3 TXD = n-2 4 5 6 7

TXD = n-1

m-2 = RXD

m-1 = RXD
C = RXD
A = RXD

B = RXD
TXD = 0
TXD = 1

TXD = 2

TXD = n

m = RXD
Figure 156: SPI master transaction

The READY event of the third byte transaction is delayed until B is extracted from RXD in occurrence
number 3 on the horizontal lifeline. The reason for this is that the third event is generated first when C is
moved from RXD-1 to RXD after B is read.
The SPI master will move the incoming byte to the RXD register after a short delay following the SCK clock
period of the last bit in the byte. This also means that the READY event will be delayed accordingly, see SPI
master transaction on page 637. Therefore, it is important that you always clear the READY event, even
if the RXD register and the data that is being received is not used.

4413_417 v1.9 636

 Peripherals

CSN

CSN
SCK

SCK
(CPHA=0)

MOSI (CPHA=1)
MOSI
MISO

MISO
READY

READY
Lifeline

Lifeline
1 1

Figure 157: SPI master transaction

6.24.2 Registers
Instances

Instance Base address Description

SPI0 0x40003000 SPI master 0

This instance is deprecated.

SPI1 0x40004000 SPI master 1

This instance is deprecated.

SPI2 0x40023000 SPI master 2

This instance is deprecated.

Register overview

Register Offset Description

EVENTS_READY 0x108 TXD byte sent and RXD byte received
INTENSET 0x304 Enable interrupt
INTENCLR 0x308 Disable interrupt
ENABLE 0x500 Enable SPI
PSEL.SCK 0x508 Pin select for SCK
PSEL.MOSI 0x50C Pin select for MOSI signal
PSEL.MISO 0x510 Pin select for MISO signal
RXD 0x518 RXD register. Register is cleared on read and the buffer pointer will be modified if read.
TXD 0x51C TXD register
FREQUENCY 0x524 SPI frequency. Accuracy depends on the HFCLK source selected.
CONFIG 0x554 Configuration register

6.24.2.1 EVENTS_READY
Address offset: 0x108
TXD byte sent and RXD byte received

4413_417 v1.9 637

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_READY TXD byte sent and RXD byte received
NotGenerated 0 Event not generated
Generated 1 Event generated

6.24.2.2 INTENSET
Address offset: 0x304
Enable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW READY Write '1' to enable interrupt for event READY
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.24.2.3 INTENCLR
Address offset: 0x308
Disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW READY Write '1' to disable interrupt for event READY
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.24.2.4 ENABLE
Address offset: 0x500
Enable SPI

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW ENABLE Enable or disable SPI
Disabled 0 Disable SPI
Enabled 1 Enable SPI

6.24.2.5 PSEL.SCK
Address offset: 0x508

4413_417 v1.9 638

 Peripherals

Pin select for SCK

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A
Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.24.2.6 PSEL.MOSI
Address offset: 0x50C
Pin select for MOSI signal

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.24.2.7 PSEL.MISO
Address offset: 0x510
Pin select for MISO signal

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.24.2.8 RXD
Address offset: 0x518
RXD register. Register is cleared on read and the buffer pointer will be modified if read.

4413_417 v1.9 639

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R RXD RX data received. Double buffered
RME

6.24.2.9 TXD
Address offset: 0x51C
TXD register

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TXD TX data to send. Double buffered.

6.24.2.10 FREQUENCY
Address offset: 0x524
SPI frequency. Accuracy depends on the HFCLK source selected.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x04000000 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW FREQUENCY SPI master data rate
K125 0x02000000 125 kbps
K250 0x04000000 250 kbps
K500 0x08000000 500 kbps
M1 0x10000000 1 Mbps
M2 0x20000000 2 Mbps
M4 0x40000000 4 Mbps
M8 0x80000000 8 Mbps

6.24.2.11 CONFIG
Address offset: 0x554
Configuration register

4413_417 v1.9 640

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW ORDER Bit order
MsbFirst 0 Most significant bit shifted out first
LsbFirst 1 Least significant bit shifted out first
B RW CPHA Serial clock (SCK) phase
Leading 0 Sample on leading edge of clock, shift serial data on trailing edge
Trailing 1 Sample on trailing edge of clock, shift serial data on leading edge
C RW CPOL Serial clock (SCK) polarity
ActiveHigh 0 Active high
ActiveLow 1 Active low

6.24.3 Electrical specification

6.24.3.1 SPI master interface electrical specifications

Symbol Description Min. Typ. Max. Units

fSPI Bit rates for SPI 30
831 Mbps

tSPI,START Time from writing TXD register to transmission started 1 µs

6.24.3.2 Serial Peripheral Interface (SPI) Master timing specifications

Symbol Description Min. Typ. Max. Units

tSPI,CSCK SCK period 125 ns
tSPI,RSCK,LD SCK rise time, standard drive 32 tRF,25pF

tSPI,RSCK,HD SCK rise time, high drive32 tHRF,25pF

tSPI,FSCK,LD SCK fall time, standard drive 32 tRF,25pF

tSPI,FSCK,HD SCK fall time, high drive32 tHRF,25pF

tSPI,WHSCK SCK high time 32 (tCSCK/2) –

tRSCK
tSPI,WLSCK SCK low time 32 (tCSCK/2) –
tFSCK
tSPI,SUMI MISO to CLK edge setup time 19 ns
tSPI,HMI CLK edge to MISO hold time 18 ns
tSPI,VMO CLK edge to MOSI valid 59 ns
tSPI,HMO MOSI hold time after CLK edge 20 ns

30
High bit rates may require GPIOs to be set as High Drive, see GPIO chapter for more details.
31
The actual maximum data rate depends on the slave's CLK to MISO and MOSI setup and hold timings.
32
At 25 pF load, including GPIO capacitance, see GPIO electrical specification.

4413_417 v1.9 641

 Peripherals

tCSCK
CPOL=0
CPHA=0
tWHSCK tRSCK
CPOL=1 tWLSCK tFSCK
SCK (out)

CPHA=0

CPOL=0
CPHA=1

CPOL=1
CPHA=1
tSUMI tHMI
MISO (in) MSb LSb

tVMO tHMO
MOSI (out) MSb LSb

Figure 158: SPI master timing diagram

6.25 SPIM — Serial peripheral interface master with

EasyDMA
The SPI master can communicate with multiple SPI slaves using individual chip select signals for each slave.
The the main features of SPIM are:
• EasyDMA direct transfer to/from RAM
• SPI mode 0-3
• Individual selection of I/O pins
• Optional D/CX output line for distinguishing between command and data bytes

4413_417 v1.9 642

 Peripherals

TASKS_

START
STOP
SUSPEND
RESUME
GPIO SPIM RAM
PSEL.MOSI TXD.PTR
buffer[0]
buffer[1]
TXD
MOSI Pin EasyDMA
buffer
SCK Pin PSEL.SCK buffer[TXD.MAXCNT-1]

CSN Pin PSEL.CSN

DCX Pin PSELDCX

buffer[0]
buffer[1]
RXD
MISO Pin EasyDMA
buffer
buffer[RXD.MAXCNT-1]
PSEL.MISO RXD.PTR

EVENTS_
STOPPED
ENDRX
END
ENDTX
STARTED

Figure 159: SPIM — SPI master with EasyDMA

6.25.1 SPI master transaction sequence

An SPI master transaction is started by triggering the START task. When started, a number of bytes will be
transmitted/received on MOSI/MISO.
The following figure illustrates an SPI master transaction.

4413_417 v1.9 643

 Peripherals

MOSI A A 0 1 2 n ORC ORC

MISO B B 0 1 2 m-2 m-1 m

SCK

CSN

ENDRX
END
ENDTX
START

Figure 160: SPI master transaction

The ENDTX is generated when all bytes in buffer TXD.PTR on page 654 are transmitted. The number of
bytes in the transmit buffer is specified in register TXD.MAXCNT on page 655. The ENDRX event will be
generated when buffer RXD.PTR on page 653 is full, meaning the number of bytes specified in register
RXD.MAXCNT on page 654 have been received. The transaction stops automatically after all bytes have
been transmitted/received. When the maximum number of bytes in the receive buffer is larger than the
number of bytes in the transmit buffer, the contents of register ORC on page 657 will be transmitted
after the last byte in the transmit buffer has been transmitted.
The END event will be generated after both the ENDRX and ENDTX events have been generated.
The SPI master can be stopped by triggering the STOP task. A STOPPED event is generated when the SPI
master has stopped. If the STOP task is triggered in the middle of a transaction, SPIM will complete the
transmission/reception of the current byte before stopping. The STOPPED event is generated even if the
STOP task is triggered while there is no ongoing transaction.
If the ENDTX event has not already been generated when the SPI master has come to a stop, the ENDTX
event will be generated even if all bytes in the buffer TXD.PTR on page 654 have not been transmitted.
If the ENDRX event has not already been generated when the SPI master has come to a stop, the ENDRX
event will be generated even if the buffer RXD.PTR on page 653 is not full.
A transaction can be suspended and resumed using the SUSPEND and RESUME tasks. When the SUSPEND
task is triggered, the SPI master will complete transmitting and receiving the current ongoing byte before
it is suspended.

6.25.2 D/CX functionality

Some SPI slaves, for example display drivers, require an additional signal from the SPI master to distinguish
between command and data bytes. For display drivers this line is often called D/CX.
SPIM provides support for such a D/CX output line. The D/CX line is set low during transmission of
command bytes and high during transmission of data bytes.
The D/CX pin number is selected using PSELDCX on page 657 and the number of command bytes
preceding the data bytes is configured using DCXCNT on page 657.
It is not allowed to write to the DCXCNT on page 657 during an ongoing transmission.
The following figure shows the use of D/CX, using SPIM.DCXCNT=1.

4413_417 v1.9 644

 Peripherals

Figure 161: D/CX example. SPIM.DCXCNT = 1.

6.25.3 Pin configuration

The SCK, CSN, DCX, MOSI, and MISO signals associated with SPIM are mapped to physical pins according to
the configuration specified in the PSEL.n registers.
The contents of registers PSEL.SCK on page 652, PSEL.CSN on page 653, PSELDCX on page 657,
PSEL.MOSI on page 652, and PSEL.MISO on page 652 are only used when SPIM is enabled, and
retained only as long as the device is in System ON mode. The PSEL.n registers can only be configured
when SPIM is disabled. Enabling/disabling is done using register ENABLE on page 651.
To ensure correct behavior, the pins used by SPIM must be configured in the GPIO peripheral as described
in GPIO configuration on page 645 before SPIM is enabled.
Only one peripheral can be assigned to drive a particular GPIO pin at a time. Failing to do so may result in
unpredictable behavior.

SPI master signal SPI master pin Direction Output value

SCK As specified in PSEL.SCK on page Output Same as CONFIG.CPOL
652
CSN As specified in PSEL.CSN on page Output Same as CONFIG.CPOL
653
DCX As specified in PSELDCX on page 657 Output 1
MOSI As specified in PSEL.MOSI on page Output 0
652
MISO As specified in PSEL.MISO on page Input Not applicable
652

Table 44: GPIO configuration

Some SPIM instances do not support automatic control of CSN, and for those the available GPIO pins
need to be used to control CSN directly. See #unique_73/unique_73_Connect_42_table.instances on page
646 for information about what features are supported in the various SPIM instances.
SPIM supports SPI modes 0 through 3. The clock polarity (CPOL) and the clock phase (CPHA) are
configured in register CONFIG on page 655.

Mode Clock polarity Clock phase

CPOL CPHA
SPI_MODE0 0 (Active High) 0 (Leading)
SPI_MODE1 0 (Active High) 1 (Trailing)
SPI_MODE2 1 (Active Low) 0 (Leading)
SPI_MODE3 1 (Active Low) 1 (Trailing)

Table 45: SPI modes

6.25.4 EasyDMA
SPIM implements EasyDMA for accessing RAM without CPU involvement.
SPIM peripheral implements the following EasyDMA channels.

4413_417 v1.9 645

 Peripherals

Channel Type Register Cluster

TXD READER TXD
RXD WRITER RXD

Table 46: SPIM EasyDMA Channels

For detailed information regarding the use of EasyDMA, see EasyDMA on page 62.
The .PTR and .MAXCNT registers are double-buffered. They can be updated and prepared for the next
transmission immediately after having received the STARTED event.
The SPI master will automatically stop transmitting after TXD.MAXCNT bytes have been transmitted
and RXD.MAXCNT bytes have been received. If RXD.MAXCNT is larger than TXD.MAXCNT, the remaining
transmitted bytes will contain the value defined in the ORC register. If TXD.MAXCNT is larger than
RXD.MAXCNT, the additional received bytes will be discarded.
The ENDRX/ENDTX events indicate that EasyDMA has finished accessing respectively the RX/TX buffer in
RAM. The END event gets generated when both RX and TX are finished accessing the buffers in RAM.
If several AHB bus masters try to access the same AHB slave at the same time, AHB bus congestion might
occur, and the behavior of the EasyDMA channel will depend on the SPIM instance. Refer to #unique_73/
unique_73_Connect_42_table.instances on page 646 for information about what behavior is supported
in the various instances.

6.25.5 Low power

To ensure lowest possible power consumption when the peripheral is not needed stop and disable SPIM.
The STOP task may not be always needed (the peripheral might already be stopped), but if it is sent,
software shall wait until the STOPPED event was received as a response before disabling the peripheral
through the ENABLE register.

6.25.6 Registers
Instances

Instance Base address Description

SPIM0 0x40003000 SPI master 0
SPIM1 0x40004000 SPI master 1
SPIM2 0x40023000 SPI master 2
SPIM3 0x4002F000 SPI master 3

Configuration

Instance Configuration
SPIM0 Not supported: > 8 Mbps data rate, CSNPOL register, DCX functionality, IFTIMING.x registers, hardware
CSN control (PSEL.CSN), stalling mechanism during AHB bus contention.
SPIM1 Not supported: > 8 Mbps data rate, CSNPOL register, DCX functionality, IFTIMING.x registers, hardware
CSN control (PSEL.CSN), stalling mechanism during AHB bus contention.
SPIM2 Not supported: > 8 Mbps data rate, CSNPOL register, DCX functionality, IFTIMING.x registers, hardware
CSN control (PSEL.CSN), stalling mechanism during AHB bus contention.
SPIM3

4413_417 v1.9 646

 Peripherals

Register overview

Register Offset Description

TASKS_START 0x010 Start SPI transaction
TASKS_STOP 0x014 Stop SPI transaction
TASKS_SUSPEND 0x01C Suspend SPI transaction
TASKS_RESUME 0x020 Resume SPI transaction
EVENTS_STOPPED 0x104 SPI transaction has stopped
EVENTS_ENDRX 0x110 End of RXD buffer reached
EVENTS_END 0x118 End of RXD buffer and TXD buffer reached
EVENTS_ENDTX 0x120 End of TXD buffer reached
EVENTS_STARTED 0x14C Transaction started
SHORTS 0x200 Shortcuts between local events and tasks
INTENSET 0x304 Enable interrupt
INTENCLR 0x308 Disable interrupt
STALLSTAT 0x400 Stall status for EasyDMA RAM accesses. The fields in this register are set to STALL by hardware
whenever a stall occurs and can be cleared (set to NOSTALL) by the CPU.
ENABLE 0x500 Enable SPIM
PSEL.SCK 0x508 Pin select for SCK
PSEL.MOSI 0x50C Pin select for MOSI signal
PSEL.MISO 0x510 Pin select for MISO signal
PSEL.CSN 0x514 Pin select for CSN
FREQUENCY 0x524 SPI frequency. Accuracy depends on the HFCLK source selected.
RXD.PTR 0x534 Data pointer
RXD.MAXCNT 0x538 Maximum number of bytes in receive buffer
RXD.AMOUNT 0x53C Number of bytes transferred in the last transaction
RXD.LIST 0x540 EasyDMA list type
TXD.PTR 0x544 Data pointer
TXD.MAXCNT 0x548 Number of bytes in transmit buffer
TXD.AMOUNT 0x54C Number of bytes transferred in the last transaction
TXD.LIST 0x550 EasyDMA list type
CONFIG 0x554 Configuration register
IFTIMING.RXDELAY 0x560 Sample delay for input serial data on MISO
IFTIMING.CSNDUR 0x564 Minimum duration between edge of CSN and edge of SCK at the start and the end of a transaction,
and minimum duration CSN will stay high between transactions if END-START shortcut is used
CSNPOL 0x568 Polarity of CSN output
PSELDCX 0x56C Pin select for DCX signal
DCXCNT 0x570 DCX configuration
ORC 0x5C0 Byte transmitted after TXD.MAXCNT bytes have been transmitted in the case when RXD.MAXCNT is
greater than TXD.MAXCNT

6.25.6.1 TASKS_START
Address offset: 0x010
Start SPI transaction

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_START Start SPI transaction
Trigger 1 Trigger task

4413_417 v1.9 647

 Peripherals

6.25.6.2 TASKS_STOP
Address offset: 0x014
Stop SPI transaction

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STOP Stop SPI transaction
Trigger 1 Trigger task

6.25.6.3 TASKS_SUSPEND
Address offset: 0x01C
Suspend SPI transaction

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_SUSPEND Suspend SPI transaction
Trigger 1 Trigger task

6.25.6.4 TASKS_RESUME
Address offset: 0x020
Resume SPI transaction

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_RESUME Resume SPI transaction
Trigger 1 Trigger task

6.25.6.5 EVENTS_STOPPED
Address offset: 0x104
SPI transaction has stopped

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_STOPPED SPI transaction has stopped
NotGenerated 0 Event not generated
Generated 1 Event generated

4413_417 v1.9 648

 Peripherals

6.25.6.6 EVENTS_ENDRX
Address offset: 0x110
End of RXD buffer reached

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_ENDRX End of RXD buffer reached
NotGenerated 0 Event not generated
Generated 1 Event generated

6.25.6.7 EVENTS_END
Address offset: 0x118
End of RXD buffer and TXD buffer reached

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_END End of RXD buffer and TXD buffer reached
NotGenerated 0 Event not generated
Generated 1 Event generated

6.25.6.8 EVENTS_ENDTX
Address offset: 0x120
End of TXD buffer reached

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_ENDTX End of TXD buffer reached
NotGenerated 0 Event not generated
Generated 1 Event generated

6.25.6.9 EVENTS_STARTED
Address offset: 0x14C
Transaction started

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_STARTED Transaction started
NotGenerated 0 Event not generated
Generated 1 Event generated

4413_417 v1.9 649

 Peripherals

6.25.6.10 SHORTS
Address offset: 0x200
Shortcuts between local events and tasks

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW END_START Shortcut between event END and task START
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut

6.25.6.11 INTENSET
Address offset: 0x304
Enable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW STOPPED Write '1' to enable interrupt for event STOPPED
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW ENDRX Write '1' to enable interrupt for event ENDRX
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW END Write '1' to enable interrupt for event END
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
D RW ENDTX Write '1' to enable interrupt for event ENDTX
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
E RW STARTED Write '1' to enable interrupt for event STARTED
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.25.6.12 INTENCLR
Address offset: 0x308
Disable interrupt

4413_417 v1.9 650

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW STOPPED Write '1' to disable interrupt for event STOPPED
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW ENDRX Write '1' to disable interrupt for event ENDRX
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW END Write '1' to disable interrupt for event END
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
D RW ENDTX Write '1' to disable interrupt for event ENDTX
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
E RW STARTED Write '1' to disable interrupt for event STARTED
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.25.6.13 STALLSTAT
Address offset: 0x400
Stall status for EasyDMA RAM accesses. The fields in this register are set to STALL by hardware whenever a
stall occurs and can be cleared (set to NOSTALL) by the CPU.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TX [1..0] Stall status for EasyDMA RAM reads
NOSTALL 0 No stall
STALL 1 A stall has occurred
B RW RX [1..0] Stall status for EasyDMA RAM writes
NOSTALL 0 No stall
STALL 1 A stall has occurred

6.25.6.14 ENABLE
Address offset: 0x500
Enable SPIM

4413_417 v1.9 651

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW ENABLE Enable or disable SPIM
Disabled 0 Disable SPIM
Enabled 7 Enable SPIM

6.25.6.15 PSEL.SCK
Address offset: 0x508
Pin select for SCK

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.25.6.16 PSEL.MOSI
Address offset: 0x50C
Pin select for MOSI signal

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.25.6.17 PSEL.MISO
Address offset: 0x510
Pin select for MISO signal

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

4413_417 v1.9 652

 Peripherals

6.25.6.18 PSEL.CSN
Address offset: 0x514
Pin select for CSN

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.25.6.19 FREQUENCY
Address offset: 0x524
SPI frequency. Accuracy depends on the HFCLK source selected.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x04000000 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW FREQUENCY SPI master data rate
K125 0x02000000 125 kbps
K250 0x04000000 250 kbps
K500 0x08000000 500 kbps
M1 0x10000000 1 Mbps
M2 0x20000000 2 Mbps
M4 0x40000000 4 Mbps
M8 0x80000000 8 Mbps
M16 0x0A000000 16 Mbps
M32 0x14000000 32 Mbps

6.25.6.20 RXD
RXD EasyDMA channel

6.25.6.20.1 RXD.PTR
Address offset: 0x534
Data pointer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PTR Data pointer

See Memory chapter for details about which memories are available for
EasyDMA.

4413_417 v1.9 653

 Peripherals

6.25.6.20.2 RXD.MAXCNT
Address offset: 0x538
Maximum number of bytes in receive buffer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW MAXCNT [0..0xFFFF] Maximum number of bytes in receive buffer

6.25.6.20.3 RXD.AMOUNT
Address offset: 0x53C
Number of bytes transferred in the last transaction

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R AMOUNT [0..0xFFFF] Number of bytes transferred in the last transaction

6.25.6.20.4 RXD.LIST
Address offset: 0x540
EasyDMA list type

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW LIST List type
Disabled 0 Disable EasyDMA list
ArrayList 1 Use array list

6.25.6.21 TXD
TXD EasyDMA channel

6.25.6.21.1 TXD.PTR
Address offset: 0x544
Data pointer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PTR Data pointer

See Memory chapter for details about which memories are available for
EasyDMA.

4413_417 v1.9 654

 Peripherals

6.25.6.21.2 TXD.MAXCNT
Address offset: 0x548
Number of bytes in transmit buffer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW MAXCNT [0..0xFFFF] Maximum number of bytes in transmit buffer

6.25.6.21.3 TXD.AMOUNT
Address offset: 0x54C
Number of bytes transferred in the last transaction

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R AMOUNT [0..0xFFFF] Number of bytes transferred in the last transaction

6.25.6.21.4 TXD.LIST
Address offset: 0x550
EasyDMA list type

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW LIST List type
Disabled 0 Disable EasyDMA list
ArrayList 1 Use array list

6.25.6.22 CONFIG
Address offset: 0x554
Configuration register

4413_417 v1.9 655

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW ORDER Bit order
MsbFirst 0 Most significant bit shifted out first
LsbFirst 1 Least significant bit shifted out first
B RW CPHA Serial clock (SCK) phase
Leading 0 Sample on leading edge of clock, shift serial data on trailing edge
Trailing 1 Sample on trailing edge of clock, shift serial data on leading edge
C RW CPOL Serial clock (SCK) polarity
ActiveHigh 0 Active high
ActiveLow 1 Active low

6.25.6.23 IFTIMING.RXDELAY
Address offset: 0x560
Sample delay for input serial data on MISO

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
A RW RXDELAY [7..0] Sample delay for input serial data on MISO. The value specifies the number
of 64 MHz clock cycles (15.625 ns) delay from the the sampling edge of
SCK (leading edge for CONFIG.CPHA = 0, trailing edge for CONFIG.CPHA =
1) until the input serial data is sampled. As en example, if RXDELAY = 0 and
CONFIG.CPHA = 0, the input serial data is sampled on the rising edge of SCK.

6.25.6.24 IFTIMING.CSNDUR
Address offset: 0x564
Minimum duration between edge of CSN and edge of SCK at the start and the end of a transaction, and
minimum duration CSN will stay high between transactions if END-START shortcut is used

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A

Reset 0x00000002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
ID R/W Field Value ID Value Description
A RW CSNDUR [0xFF..0] Minimum duration between edge of CSN and edge of SCK at the start and
end of a transaction. If END-START shortcut is used, minimum duration CSN
will stay high between transactions. The value is specified in number of 64
MHz clock cycles (15.625 ns).

Note that for low values of CSNDUR, the system turnaround time will
dominate the actual time between transactions.

6.25.6.25 CSNPOL
Address offset: 0x568
Polarity of CSN output

4413_417 v1.9 656

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW CSNPOL Polarity of CSN output
LOW 0 Active low (idle state high)
HIGH 1 Active high (idle state low)

6.25.6.26 PSELDCX
Address offset: 0x56C
Pin select for DCX signal

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.25.6.27 DCXCNT
Address offset: 0x570
DCX configuration

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW DCXCNT 0x0..0xF This register specifies the number of command bytes preceding the data
bytes. The PSEL.DCX line will be low during transmission of command bytes
and high during transmission of data bytes. Value 0xF indicates that all bytes
are command bytes.

6.25.6.28 ORC
Address offset: 0x5C0
Byte transmitted after TXD.MAXCNT bytes have been transmitted in the case when RXD.MAXCNT is
greater than TXD.MAXCNT

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW ORC Byte transmitted after TXD.MAXCNT bytes have been transmitted in the
case when RXD.MAXCNT is greater than TXD.MAXCNT.

4413_417 v1.9 657

 Peripherals

6.25.7 Electrical specification

6.25.7.1 Timing specifications

Symbol Description Min. Typ. Max. Units

fSPIM Bit rates for SPIM 33 32 Mbps

tSPIM,START Time from START task to transmission started 1 µs

tSPIM,CSCK SCK period 31.25 ns
tSPIM,RSCK,LD SCK rise time, standard drive 34 tRF,25pF

tSPIM,RSCK,HD SCK rise time, high drive 34 tHRF,25pF

tSPIM,FSCK,LD SCK fall time, standard drive34 tRF,25pF

tSPIM,FSCK,HD SCK fall time, high drive 34 tHRF,25pF

tSPIM,WHSCK SCK high time 34 (tCSCK/2) –

tRSCK
tSPIM,WLSCK SCK low time34 (tCSCK/2) –
tFSCK
tSPIM,SUMI MISO to CLK edge setup time 19 ns
tSPIM,HMI CLK edge to MISO hold time 18 ns
tSPIM,VMO CLK edge to MOSI valid, SCK frequency ≤ 8 MHz 59 ns
tSPIM,VMO,HS CLK edge to MOSI valid, SCK frequency > 8 MHz 8 ns
tSPIM,HMO MOSI hold time after CLK edge 20 ns

tCSCK
CPOL=0
CPHA=0
tWHSCK tRSCK
CPOL=1 tWLSCK tFSCK
SCK (out)

CPHA=0

CPOL=0
CPHA=1

CPOL=1
CPHA=1

CSNPOL=0
CSN (out)

CSNPOL=1
IFTIMING.CSNDUR IFTIMING.CSNDUR

tSUMI tHMI
MISO (in) MSb LSb

tVMO tHMO
MOSI (out) MSb LSb

Figure 162: SPIM timing diagram

33
High bit rates may require GPIOs to be set as High Drive, see GPIO chapter for more details.
34
At 25 pF load, including GPIO pin capacitance, see GPIO electrical specification.

4413_417 v1.9 658

 Peripherals

6.26 SPIS — Serial peripheral interface slave with

EasyDMA
SPI slave (SPIS) is implemented with EasyDMA support for ultra-low power serial communication from an
external SPI master. EasyDMA, in conjunction with hardware-based semaphore mechanisms, removes all
real-time requirements associated with controlling the SPI slave from a low priority CPU execution context.
PSEL.CSN PSEL.MISO PSEL.MOSI PSEL.SCK

SPIS
CSN MISO MOSI

ACQUIRE

SPI slave tranceiver

RELEASE
Semaphore

ACQUIRED

END
DEF

OVERREAD

OVERFLOW TXD.PTR EasyDMA EasyDMA RXD.PTR

RAM

TXD RXD

TXD+1 RXD+1

TXD+2 RXD+2

TXD+n RXD+n

Figure 163: SPI slave

The SPIS supports SPI modes 0 through 3. The CONFIG register allows setting CPOL and CPHA
appropriately.

Mode Clock polarity Clock phase

CPOL CPHA
SPI_MODE0 0 (Active High) 0 (Trailing Edge)
SPI_MODE1 0 (Active High) 1 (Leading Edge)
SPI_MODE2 1 (Active Low) 0 (Trailing Edge)
SPI_MODE3 1 (Active Low) 1 (Leading Edge)

Table 47: SPI modes

6.26.1 Shared resources

The SPI slave shares registers and other resources with other peripherals that have the same ID as the SPI
slave. Therefore, you must disable all peripherals that have the same ID as the SPI slave before the SPI
slave can be configured and used.
Disabling a peripheral that has the same ID as the SPI slave will not reset any of the registers that are
shared with the SPI slave. It is important to configure all relevant SPI slave registers explicitly to secure that
it operates correctly.
The Instantiation table in Instantiation on page 24 shows which peripherals have the same ID as the SPI
slave.

4413_417 v1.9 659

 Peripherals

6.26.2 EasyDMA
The SPIS implements EasyDMA for accessing RAM without CPU involvement.
The SPIS peripheral implements the following EasyDMA channels.

Channel Type Register Cluster

TXD READER TXD
RXD WRITER RXD

Table 48: SPIS EasyDMA Channels

For detailed information regarding the use of EasyDMA, see EasyDMA on page 62.
If RXD.MAXCNT is larger than TXD.MAXCNT, the remaining transmitted bytes will contain the value defined
in the ORC register.
The END event indicates that EasyDMA has finished accessing the buffer in RAM.

6.26.3 SPI slave operation

SPI slave uses two memory pointers, RXD.PTR and TXD.PTR, that point to the RXD buffer (receive buffer)
and TXD buffer (transmit buffer) respectively. Since these buffers are located in RAM, which can be
accessed by both the SPI slave and the CPU, a hardware based semaphore mechanism is implemented to
enable safe sharing.
See SPI transaction when shortcut between END and ACQUIRE is enabled on page 662.
Before the CPU can safely update the RXD.PTR and TXD.PTR pointers, it must first acquire the SPI
semaphore. The CPU can acquire the semaphore by triggering the ACQUIRE task and then receiving the
ACQUIRED event. When the CPU has updated the RXD.PTR and TXD.PTR pointers the CPU must release the
semaphore before the SPI slave will be able to acquire it. The CPU releases the semaphore by triggering
the RELEASE task. This is illustrated in SPI transaction when shortcut between END and ACQUIRE is
enabled on page 662. Triggering the RELEASE task when the semaphore is not granted to the CPU will
have no effect.
The semaphore mechanism does not, at any time, prevent the CPU from performing read or write access
to the RXD.PTR register, the TXD.PTR registers, or the RAM that these pointers are pointing to. The
semaphore is only telling when these can be updated by the CPU so that safe sharing is achieved.
The semaphore is by default assigned to the CPU after the SPI slave is enabled. No ACQUIRED event will be
generated for this initial semaphore handover. An ACQUIRED event will be generated immediately if the
ACQUIRE task is triggered while the semaphore is assigned to the CPU.
The SPI slave will try to acquire the semaphore when CSN goes low. If the SPI slave does not manage to
acquire the semaphore at this point, the transaction will be ignored. This means that all incoming data on
MOSI will be discarded, and the DEF (default) character will be clocked out on the MISO line throughout
the whole transaction. This will also be the case even if the semaphore is released by the CPU during the
transaction. In case of a race condition where the CPU and the SPI slave try to acquire the semaphore at
the same time, as illustrated in lifeline item 2 in SPI transaction when shortcut between END and ACQUIRE
is enabled on page 662, the semaphore will be granted to the CPU.
If the SPI slave acquires the semaphore, the transaction will be granted. The incoming data on MOSI will
be stored in the RXD buffer and the data in the TXD buffer will be clocked out on MISO.
When a granted transaction is completed and CSN goes high, the SPI slave will automatically release the
semaphore and generate the END event.

4413_417 v1.9 660

 Peripherals

As long as the semaphore is available, the SPI slave can be granted multiple transactions one after the
other. If the CPU is not able to reconfigure the TXD.PTR and RXD.PTR between granted transactions, the
same TX data will be clocked out and the RX buffers will be overwritten. To prevent this from happening,
the END_ACQUIRE shortcut can be used. With this shortcut enabled, the semaphore will be handed over
to the CPU automatically after the granted transaction has completed. This enables the CPU to update the
TXPTR and RXPTR between every granted transaction.
If the CPU tries to acquire the semaphore while it is assigned to the SPI slave, an immediate handover
will not be granted. However, the semaphore will be handed over to the CPU as soon as the SPI slave
has released the semaphore after the granted transaction is completed. If the END_ACQUIRE shortcut
is enabled and the CPU has triggered the ACQUIRE task during a granted transaction, only one ACQUIRE
request will be served following the END event.
The MAXRX register specifies the maximum number of bytes the SPI slave can receive in one granted
transaction. If the SPI slave receives more than MAXRX number of bytes, an OVERFLOW will be indicated
in the STATUS register and the incoming bytes will be discarded.
The MAXTX parameter specifies the maximum number of bytes the SPI slave can transmit in one granted
transaction. If the SPI slave is forced to transmit more than MAXTX number of bytes, an OVERREAD will be
indicated in the STATUS register and the ORC character will be clocked out.
The RXD.AMOUNT and TXD.AMOUNT registers are updated when a granted transaction is completed. The
TXD.AMOUNT register indicates how many bytes were read from the TX buffer in the last transaction. This
does not include the ORC (over-read) characters. Similarly, the RXD.AMOUNT register indicates how many
bytes were written into the RX buffer in the last transaction.
The ENDRX event is generated when the RX buffer has been filled.

4413_417 v1.9 661

 Peripherals

SPI master can use the DEF

character to stop the transaction as
soon as possible if the transaction is
not granted.
Transaction status

Ignored Ignored Granted

CSN
SCK
MOSI

0 0 1 2 0 1 2
MISO

DEF DEF DEF DEF A B C

Semaphore assignment

CPU Free CPU Free SPIS CPUPENDING CPU

ACQUIRED
ACQUIRED

ACQUIRED

END
&
Lifeline

1 2 3 4
RELEASE

RELEASE
ACQUIRE

ACQUIRE

ACQUIRE

Figure 164: SPI transaction when shortcut between END and ACQUIRE is enabled

6.26.4 Pin configuration

The CSN, SCK, MOSI, and MISO signals associated with the SPI slave are mapped to physical pins according
to the configuration specified in the PSEL.CSN, PSEL.SCK, PSEL.MOSI, and PSEL.MISO registers respectively.
If the CONNECT field of any of these registers is set to Disconnected, the associated SPI slave signal will not
be connected to any physical pins.
The PSEL.CSN, PSEL.SCK, PSEL.MOSI, and PSEL.MISO registers and their configurations are only used as
long as the SPI slave is enabled, and retained only as long as the device is in System ON mode. See POWER
— Power supply on page 80 chapter for more information about power modes. When the peripheral is
disabled, the pins will behave as regular GPIOs and use the configuration in their respective OUT bit field
and PIN_CNF[n] register. PSEL.CSN, PSEL.SCK, PSEL.MOSI, and PSEL.MISO must only be configured when
the SPI slave is disabled.
To secure correct behavior in the SPI slave, the pins used by the SPI slave must be configured in the GPIO
peripheral as described in GPIO configuration before enabling peripheral on page 663 before enabling
the SPI slave. This is to secure that the pins used by the SPI slave are driven correctly if the SPI slave itself
is temporarily disabled, or if the device temporarily enters System OFF. This configuration must be retained
in the GPIO for the selected I/Os as long as the SPI slave is to be recognized by an external SPI master.
The MISO line is set in high impedance as long as the SPI slave is not selected with CSN.

4413_417 v1.9 662

 Peripherals

Only one peripheral can be assigned to drive a particular GPIO pin at a time. Failing to do so may result in
unpredictable behavior.

SPI signal SPI pin Direction Output value Comment

CSN As specified in PSEL.CSN Input Not applicable
SCK As specified in PSEL.SCK Input Not applicable
MOSI As specified in PSEL.MOSI Input Not applicable
MISO As specified in PSEL.MISO Input Not applicable Emulates that the SPI slave is not selected.

Table 49: GPIO configuration before enabling peripheral

6.26.5 Registers
Instances

Instance Base address Description

SPIS0 0x40003000 SPI slave 0
SPIS1 0x40004000 SPI slave 1
SPIS2 0x40023000 SPI slave 2

Register overview

Register Offset Description

TASKS_ACQUIRE 0x024 Acquire SPI semaphore
TASKS_RELEASE 0x028 Release SPI semaphore, enabling the SPI slave to acquire it
EVENTS_END 0x104 Granted transaction completed
EVENTS_ENDRX 0x110 End of RXD buffer reached
EVENTS_ACQUIRED 0x128 Semaphore acquired
SHORTS 0x200 Shortcuts between local events and tasks
INTENSET 0x304 Enable interrupt
INTENCLR 0x308 Disable interrupt
SEMSTAT 0x400 Semaphore status register
STATUS 0x440 Status from last transaction
ENABLE 0x500 Enable SPI slave
PSEL.SCK 0x508 Pin select for SCK
PSEL.MISO 0x50C Pin select for MISO signal
PSEL.MOSI 0x510 Pin select for MOSI signal
PSEL.CSN 0x514 Pin select for CSN signal
RXD.PTR 0x534 RXD data pointer
RXD.MAXCNT 0x538 Maximum number of bytes in receive buffer
RXD.AMOUNT 0x53C Number of bytes received in last granted transaction
RXD.LIST 0x540 EasyDMA list type
TXD.PTR 0x544 TXD data pointer
TXD.MAXCNT 0x548 Maximum number of bytes in transmit buffer
TXD.AMOUNT 0x54C Number of bytes transmitted in last granted transaction
TXD.LIST 0x550 EasyDMA list type
CONFIG 0x554 Configuration register
DEF 0x55C Default character. Character clocked out in case of an ignored transaction.
ORC 0x5C0 Over-read character

4413_417 v1.9 663

 Peripherals

6.26.5.1 TASKS_ACQUIRE
Address offset: 0x024
Acquire SPI semaphore

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_ACQUIRE Acquire SPI semaphore
Trigger 1 Trigger task

6.26.5.2 TASKS_RELEASE
Address offset: 0x028
Release SPI semaphore, enabling the SPI slave to acquire it

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_RELEASE Release SPI semaphore, enabling the SPI slave to acquire it
Trigger 1 Trigger task

6.26.5.3 EVENTS_END
Address offset: 0x104
Granted transaction completed

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_END Granted transaction completed
NotGenerated 0 Event not generated
Generated 1 Event generated

6.26.5.4 EVENTS_ENDRX
Address offset: 0x110
End of RXD buffer reached

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_ENDRX End of RXD buffer reached
NotGenerated 0 Event not generated
Generated 1 Event generated

4413_417 v1.9 664

 Peripherals

6.26.5.5 EVENTS_ACQUIRED
Address offset: 0x128
Semaphore acquired

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_ACQUIRED Semaphore acquired
NotGenerated 0 Event not generated
Generated 1 Event generated

6.26.5.6 SHORTS
Address offset: 0x200
Shortcuts between local events and tasks

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW END_ACQUIRE Shortcut between event END and task ACQUIRE
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut

6.26.5.7 INTENSET
Address offset: 0x304
Enable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW END Write '1' to enable interrupt for event END
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW ENDRX Write '1' to enable interrupt for event ENDRX
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW ACQUIRED Write '1' to enable interrupt for event ACQUIRED
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.26.5.8 INTENCLR
Address offset: 0x308
Disable interrupt

4413_417 v1.9 665

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW END Write '1' to disable interrupt for event END
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW ENDRX Write '1' to disable interrupt for event ENDRX
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW ACQUIRED Write '1' to disable interrupt for event ACQUIRED
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.26.5.9 SEMSTAT
Address offset: 0x400
Semaphore status register

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A

Reset 0x00000001 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
ID R/W Field Value ID Value Description
A R SEMSTAT Semaphore status
Free 0 Semaphore is free
CPU 1 Semaphore is assigned to CPU
SPIS 2 Semaphore is assigned to SPI slave
CPUPending 3 Semaphore is assigned to SPI but a handover to the CPU is pending

6.26.5.10 STATUS
Address offset: 0x440
Status from last transaction
Individual bits are cleared by writing a 1 to the bits that shall be cleared

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW OVERREAD TX buffer over-read detected, and prevented
NotPresent 0 Read: error not present
Present 1 Read: error present
Clear 1 Write: clear error on writing '1'
B RW OVERFLOW RX buffer overflow detected, and prevented
NotPresent 0 Read: error not present
Present 1 Read: error present
Clear 1 Write: clear error on writing '1'

4413_417 v1.9 666

 Peripherals

6.26.5.11 ENABLE
Address offset: 0x500
Enable SPI slave

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW ENABLE Enable or disable SPI slave
Disabled 0 Disable SPI slave
Enabled 2 Enable SPI slave

6.26.5.12 PSEL.SCK
Address offset: 0x508
Pin select for SCK

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.26.5.13 PSEL.MISO
Address offset: 0x50C
Pin select for MISO signal

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.26.5.14 PSEL.MOSI
Address offset: 0x510
Pin select for MOSI signal

4413_417 v1.9 667

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.26.5.15 PSEL.CSN
Address offset: 0x514
Pin select for CSN signal

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.26.5.16 RXD.PTR
Address offset: 0x534
RXD data pointer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A
Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PTR RXD data pointer

See the memory chapter for details about which memories are available for
EasyDMA.

6.26.5.17 RXD.MAXCNT
Address offset: 0x538
Maximum number of bytes in receive buffer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW MAXCNT [0..0xFFFF] Maximum number of bytes in receive buffer

6.26.5.18 RXD.AMOUNT
Address offset: 0x53C

4413_417 v1.9 668

 Peripherals

Number of bytes received in last granted transaction

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A
Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R AMOUNT [0..0xFFFF] Number of bytes received in the last granted transaction

6.26.5.19 RXD.LIST
Address offset: 0x540
EasyDMA list type

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW LIST List type
Disabled 0 Disable EasyDMA list
ArrayList 1 Use array list

6.26.5.20 TXD.PTR
Address offset: 0x544
TXD data pointer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PTR TXD data pointer

See the memory chapter for details about which memories are available for
EasyDMA.

6.26.5.21 TXD.MAXCNT
Address offset: 0x548
Maximum number of bytes in transmit buffer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW MAXCNT [0..0xFFFF] Maximum number of bytes in transmit buffer

6.26.5.22 TXD.AMOUNT
Address offset: 0x54C
Number of bytes transmitted in last granted transaction

4413_417 v1.9 669

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R AMOUNT [0..0xFFFF] Number of bytes transmitted in last granted transaction

6.26.5.23 TXD.LIST
Address offset: 0x550
EasyDMA list type

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW LIST List type
Disabled 0 Disable EasyDMA list
ArrayList 1 Use array list

6.26.5.24 CONFIG
Address offset: 0x554
Configuration register

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW ORDER Bit order
MsbFirst 0 Most significant bit shifted out first
LsbFirst 1 Least significant bit shifted out first
B RW CPHA Serial clock (SCK) phase
Leading 0 Sample on leading edge of clock, shift serial data on trailing edge
Trailing 1 Sample on trailing edge of clock, shift serial data on leading edge
C RW CPOL Serial clock (SCK) polarity
ActiveHigh 0 Active high
ActiveLow 1 Active low

6.26.5.25 DEF
Address offset: 0x55C
Default character. Character clocked out in case of an ignored transaction.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW DEF Default character. Character clocked out in case of an ignored transaction.

6.26.5.26 ORC
Address offset: 0x5C0

4413_417 v1.9 670

 Peripherals

Over-read character

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A
Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW ORC Over-read character. Character clocked out after an over-read of the
transmit buffer.

6.26.6 Electrical specification

6.26.6.1 SPIS slave interface electrical specifications

Symbol Description Min. Typ. Max. Units

fSPIS Bit rates for SPIS35 836 Mbps

tSPIS,START Time from RELEASE task to receive/transmit (CSN active) 0.125 µs

6.26.6.2 Serial Peripheral Interface Slave (SPIS) timing specifications

Symbol Description Min. Typ. Max. Units

tSPIS,CSCKIN SCK input period 125 ns
tSPIS,RFSCKIN SCK input rise/fall time 30 ns
tSPIS,WHSCKIN SCK input high time 30 ns
tSPIS,WLSCKIN SCK input low time 30 ns
tSPIS,SUCSN CSN to CLK setup time 1000 ns
tSPIS,HCSN CLK to CSN hold time 1000 ns
tSPIS,ASA CSN to MISO driven 0 ns
tSPIS,ASO CSN to MISO valid 37 1000 ns

tSPIS,DISSO CSN to MISO disabled 37 68 ns

tSPIS,CWH CSN inactive time 300 ns

tSPIS,VSO CLK edge to MISO valid 59 ns
tSPIS,HSO MISO hold time after CLK edge 2038 ns

tSPIS,SUSI MOSI to CLK edge setup time 19 ns

tSPIS,HSI CLK edge to MOSI hold time 18 ns

35
High bit rates may require GPIOs to be set as High Drive, see GPIO chapter for more details.
36
The actual maximum data rate depends on the master's CLK to MISO and MOSI setup and hold
timings.
37
At 25 pF load, including GPIO capacitance, see GPIO electrical specification.
38
This is to ensure compatibility to SPI masters sampling MISO on the same edge as MOSI is output.

4413_417 v1.9 671

 Peripherals

CSN (in)

tSUCSN tCSCKIN tHCSN tCWH

CPOL=0
CPHA=0
SCK (in)

tWHSCKIN tRSCKIN
CPOL=1 tWLSCKIN tFSCKIN
CPHA=0 tASO tDISSO
tASA tVSO tHSO tHSO
MISO (out) MSb LSb

tSUSI tHSI
MOSI (in) MSb LSb

CSN (in)

tSUCSN tCSCKIN tHCSN tCWH

CPOL=0
CPHA=1
SCK (in)

tWHSCKIN tRSCKIN
CPOL=1 tWLSCKIN tFSCKIN
CPHA=1
tASO tVSO tHSO tDISSO
tASA
MISO (out) MSb LSb

tSUSI tHSI
MOSI (in) MSb LSb

Figure 165: SPIS timing diagram

CSN

tSUCSN,CPHA0 tCSCK tHCSN

CPOL=0
CPHA=0
tWHSCK tRSCK
CPOL=1 tWLSCK tFSCK
CPHA=0 tSUCSN,CPHA1
SCK

CPOL=0
CPHA=1

CPOL=1
CPHA=1
tSUMI tHMI tDISSO
tASO tVSO tHSO tHSO
tASA
MISO MSb LSb

Master tVMO tHMO

Slave tSUSI tHSI

MOSI MSb LSb

Figure 166: Common SPIM and SPIS timing diagram

4413_417 v1.9 672

 Peripherals

6.27 SWI — Software interrupts

A set of interrupts have been reserved for use as software interrupts.

6.27.1 Registers
Instances

Instance Base address Description

SWI0 0x40014000 Software interrupt 0
SWI1 0x40015000 Software interrupt 1
SWI2 0x40016000 Software interrupt 2
SWI3 0x40017000 Software interrupt 3
SWI4 0x40018000 Software interrupt 4
SWI5 0x40019000 Software interrupt 5

6.28 TEMP — Temperature sensor

The temperature sensor measures die temperature over the temperature range of the device. Linearity
compensation can be implemented if required by the application.
Listed here are the main features for TEMP:
• Temperature range is greater than or equal to operating temperature of the device
• Resolution is 0.25 degrees
TEMP is started by triggering the START task.
When the temperature measurement is completed, a DATARDY event will be generated and the result of
the measurement can be read from the TEMP register.
To achieve the measurement accuracy stated in the electrical specification, the crystal oscillator must be
selected as the HFCLK source, see CLOCK — Clock control on page 156 for more information.
When the temperature measurement is completed, TEMP analog electronics power down to save power.
TEMP only supports one-shot operation, meaning that every TEMP measurement has to be explicitly
started using the START task.

6.28.1 Registers
Instances

Instance Base address Description

TEMP 0x4000C000 Temperature sensor

Register overview

Register Offset Description

TASKS_START 0x000 Start temperature measurement
TASKS_STOP 0x004 Stop temperature measurement
EVENTS_DATARDY 0x100 Temperature measurement complete, data ready

4413_417 v1.9 673

 Peripherals

Register Offset Description

INTENSET 0x304 Enable interrupt
INTENCLR 0x308 Disable interrupt
TEMP 0x508 Temperature in °C (0.25° steps)
A0 0x520 Slope of first piecewise linear function
A1 0x524 Slope of second piecewise linear function
A2 0x528 Slope of third piecewise linear function
A3 0x52C Slope of fourth piecewise linear function
A4 0x530 Slope of fifth piecewise linear function
A5 0x534 Slope of sixth piecewise linear function
B0 0x540 y-intercept of first piecewise linear function
B1 0x544 y-intercept of second piecewise linear function
B2 0x548 y-intercept of third piecewise linear function
B3 0x54C y-intercept of fourth piecewise linear function
B4 0x550 y-intercept of fifth piecewise linear function
B5 0x554 y-intercept of sixth piecewise linear function
T0 0x560 End point of first piecewise linear function
T1 0x564 End point of second piecewise linear function
T2 0x568 End point of third piecewise linear function
T3 0x56C End point of fourth piecewise linear function
T4 0x570 End point of fifth piecewise linear function

6.28.1.1 TASKS_START
Address offset: 0x000
Start temperature measurement

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_START Start temperature measurement
Trigger 1 Trigger task

6.28.1.2 TASKS_STOP
Address offset: 0x004
Stop temperature measurement

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STOP Stop temperature measurement
Trigger 1 Trigger task

6.28.1.3 EVENTS_DATARDY
Address offset: 0x100
Temperature measurement complete, data ready

4413_417 v1.9 674

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_DATARDY Temperature measurement complete, data ready
NotGenerated 0 Event not generated
Generated 1 Event generated

6.28.1.4 INTENSET
Address offset: 0x304
Enable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW DATARDY Write '1' to enable interrupt for event DATARDY
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.28.1.5 INTENCLR
Address offset: 0x308
Disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW DATARDY Write '1' to disable interrupt for event DATARDY
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.28.1.6 TEMP
Address offset: 0x508
Temperature in °C (0.25° steps)

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R TEMP Temperature in °C (0.25° steps)

Result of temperature measurement. Die temperature in °C, 2's

complement format, 0.25 °C steps.

Decision point: DATARDY

4413_417 v1.9 675

 Peripherals

6.28.1.7 A0
Address offset: 0x520
Slope of first piecewise linear function

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A

Reset 0x00000326 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 0 0 1 0 0 1 1 0
ID R/W Field Value ID Value Description
A RW A0 Slope of first piecewise linear function

6.28.1.8 A1
Address offset: 0x524
Slope of second piecewise linear function

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A

Reset 0x00000348 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 0 1 0 0 1 0 0 0
ID R/W Field Value ID Value Description
A RW A1 Slope of second piecewise linear function

6.28.1.9 A2
Address offset: 0x528
Slope of third piecewise linear function

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A

Reset 0x000003AA 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 1 0 1 0 1 0
ID R/W Field Value ID Value Description
A RW A2 Slope of third piecewise linear function

6.28.1.10 A3
Address offset: 0x52C
Slope of fourth piecewise linear function

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A

Reset 0x0000040E 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 1 1 1 0
ID R/W Field Value ID Value Description
A RW A3 Slope of fourth piecewise linear function

6.28.1.11 A4
Address offset: 0x530
Slope of fifth piecewise linear function

4413_417 v1.9 676

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A

Reset 0x000004BD 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 1 0 1 1 1 1 0 1
ID R/W Field Value ID Value Description
A RW A4 Slope of fifth piecewise linear function

6.28.1.12 A5
Address offset: 0x534
Slope of sixth piecewise linear function

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A

Reset 0x000005A3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 1 0 1 0 0 0 1 1
ID R/W Field Value ID Value Description
A RW A5 Slope of sixth piecewise linear function

6.28.1.13 B0
Address offset: 0x540
y-intercept of first piecewise linear function

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A

Reset 0x00003FEF 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 0 1 1 1 1
ID R/W Field Value ID Value Description
A RW B0 y-intercept of first piecewise linear function

6.28.1.14 B1
Address offset: 0x544
y-intercept of second piecewise linear function

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A

Reset 0x00003FBE 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 1 1 1 1 1 0
ID R/W Field Value ID Value Description
A RW B1 y-intercept of second piecewise linear function

6.28.1.15 B2
Address offset: 0x548
y-intercept of third piecewise linear function

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A

Reset 0x00003FBE 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 1 1 1 1 1 0
ID R/W Field Value ID Value Description
A RW B2 y-intercept of third piecewise linear function

4413_417 v1.9 677

 Peripherals

6.28.1.16 B3
Address offset: 0x54C
y-intercept of fourth piecewise linear function

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A

Reset 0x00000012 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 1 0
ID R/W Field Value ID Value Description
A RW B3 y-intercept of fourth piecewise linear function

6.28.1.17 B4
Address offset: 0x550
y-intercept of fifth piecewise linear function

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A

Reset 0x00000124 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0 1 0 0
ID R/W Field Value ID Value Description
A RW B4 y-intercept of fifth piecewise linear function

6.28.1.18 B5
Address offset: 0x554
y-intercept of sixth piecewise linear function

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A

Reset 0x0000027C 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 1 1 1 1 1 0 0
ID R/W Field Value ID Value Description
A RW B5 y-intercept of sixth piecewise linear function

6.28.1.19 T0
Address offset: 0x560
End point of first piecewise linear function

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A

Reset 0x000000E2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 1 0
ID R/W Field Value ID Value Description
A RW T0 End point of first piecewise linear function

6.28.1.20 T1
Address offset: 0x564
End point of second piecewise linear function

4413_417 v1.9 678

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW T1 End point of second piecewise linear function

6.28.1.21 T2
Address offset: 0x568
End point of third piecewise linear function

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A

Reset 0x00000019 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 0 0 1
ID R/W Field Value ID Value Description
A RW T2 End point of third piecewise linear function

6.28.1.22 T3
Address offset: 0x56C
End point of fourth piecewise linear function

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A

Reset 0x0000003C 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 0 0
ID R/W Field Value ID Value Description
A RW T3 End point of fourth piecewise linear function

6.28.1.23 T4
Address offset: 0x570
End point of fifth piecewise linear function

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A

Reset 0x00000050 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0 0
ID R/W Field Value ID Value Description
A RW T4 End point of fifth piecewise linear function

6.28.2 Electrical specification

6.28.2.1 Temperature Sensor Electrical Specification

Symbol Description Min. Typ. Max. Units

tTEMP Time required for temperature measurement 36 µs
TTEMP,RANGE Temperature sensor range -40 85 °C
TTEMP,ACC Temperature sensor accuracy -5 5 °C
TTEMP,RES Temperature sensor resolution 0.25 °C
TTEMP,STB Sample to sample stability at constant device temperature -0.25 0.25 °C
TTEMP,OFFST Sample offset at 25°C -2.5 2.5 °C

4413_417 v1.9 679

 Peripherals

6.29 TWI — I2C compatible two-wire interface

The TWI master is compatible with I2C operating at 100 kHz and 400 kHz.

PSEL.SDA PSEL.SCL PSEL.SDA

STARTRX RXDRDY
STARTTX TXDSENT
SUSPEND RXD TXD BB
RXD TXD
RESUME SUSPENDED
(signal) (signal)
ERROR
STOP
STOPPED

Figure 167: TWI master's main features

6.29.1 Functional description

This TWI master is not compatible with CBUS. The TWI transmitter and receiver are single buffered.
See TWI master's main features on page 680.
A TWI setup with one master and three slaves is shown in the following figure. This TWI master is only
able to operate as the only master on the TWI bus.

VDD VDD
TWI slave TWI slave TWI slave
(EEPROM) (Sensor)
TWI master
Address = b1011001 Address = b1011000 Address = b1011011
R R
SDA SCL SCL SDA SCL SDA SCL SDA

Figure 168: A typical TWI setup with one master and three slaves

This TWI master supports clock stretching performed by the slaves. The TWI master is started by triggering
the STARTTX or STARTRX tasks, and stopped by triggering the STOP task.
If a NACK is clocked in from the slave, the TWI master will generate an ERROR event.

6.29.2 Master mode pin configuration

The different signals SCL and SDA associated with the TWI master are mapped to physical pins according to
the configuration specified in the PSEL.SCL and PSEL.SDA registers respectively.
If the CONNECT field of a PSEL.xxx register is set to Disconnected, the associated TWI signal is not
connected to any physical pin. The PSEL.SCL and PSEL.SDA registers and their configurations are only used
as long as the TWI master is enabled, and retained only as long as the device is in ON mode. PSEL.SCL and
PSEL.SDA must only be configured when TWI is disabled.

4413_417 v1.9 680

 Peripherals

To secure correct signal levels on the pins used by the TWI master when the system is in OFF mode, and
when the TWI master is disabled, these pins must be configured in the GPIO peripheral as described in
GPIO configuration on page 681.
Only one peripheral can be assigned to drive a particular GPIO pin at a time, failing to do so may result in
unpredictable behavior.

TWI master signal TWI master pin Direction Drive strength Output value

SCL As specified in PSEL.SCL Input S0D1 Not applicable

SDA As specified in PSEL.SDA Input S0D1 Not applicable

Table 50: GPIO configuration

6.29.3 Shared resources

TWI shares registers and other resources with other peripherals that have the same ID as TWI.
Therefore, you must disable all peripherals that have the same ID as TWI before TWI can be configured
and used. Disabling a peripheral that has the same ID as TWI will not reset any of the registers that are
shared with TWI. It is therefore important to configure all relevant TWI registers explicitly to secure that it
operates correctly.
The Instantiation table in Instantiation on page 24 shows which peripherals have the same ID as TWI.

6.29.4 Master write sequence

A TWI master write sequence is started by triggering the STARTTX task. After the STARTTX task has been
triggered, the TWI master will generate a start condition on the TWI bus, followed by clocking out the
address and the READ/WRITE bit set to 0 (WRITE=0, READ=1).
The address must match the address of the slave device that the master wants to write to. The READ/
WRITE bit is followed by an ACK/NACK bit (ACK=0 or NACK=1) generated by the slave.
After receiving the ACK bit, the TWI master will clock out the data bytes that are written to the TXD
register. Each byte clocked out from the master will be followed by an ACK/NACK bit clocked in from the
slave. A TXDSENT event will be generated each time the TWI master has clocked out a TXD byte, and the
associated ACK/NACK bit has been clocked in from the slave.
The TWI master transmitter is single buffered. A second byte can only be written to the TXD register after
the previous byte has been clocked out and the ACK/NACK bit clocked in, that is, after the TXDSENT event
has been generated.
If the CPU is prevented from writing to TXD when the TWI master is ready to clock out a byte, the TWI
master will stretch the clock until the CPU has written a byte to the TXD register.
A typical TWI master write sequence is illustrated in The TWI master writing data to a slave on page
682. Occurrence 3 in the figure illustrates delayed processing of the TXDSENT event associated with
TXD byte 1. In this scenario the TWI master will stretch the clock to prevent writing erroneous data to the
slave.

4413_417 v1.9 681

 Peripherals

START

WRITE

STOP
ACK

ACK

ACK

ACK

ACK

ACK
TWI
ADDR 0 1 2 N-1 N

STOPPED
TXDSENT
TXDSENT

TXDSENT
TXDSENT
CPU Lifeline

1 2 3 4 6 7
STARTTX

TXD = N
TXD = 0

TXD = 1

TXD = 2

STOP
Figure 169: The TWI master writing data to a slave

The TWI master write sequence is stopped when the STOP task is triggered, causing the TWI master to
generate a stop condition on the TWI bus.

6.29.5 Master read sequence

A TWI master read sequence is started by triggering the STARTRX task. After the STARTRX task has been
triggered, the TWI master will generate a start condition on the TWI bus, followed by clocking out the
address and the READ/WRITE bit set to 1 (WRITE = 0, READ = 1).
The address must match the address of the slave device that the master wants to read from. The READ/
WRITE bit is followed by an ACK/NACK bit (ACK=0 or NACK = 1) generated by the slave.
After having sent the ACK bit, the TWI slave will send data to the master using the clock generated by the
master.
The TWI master will generate a RXDRDY event every time a new byte is received in the RXD register.
After receiving a byte, the TWI master will delay sending the ACK/NACK bit by stretching the clock until the
CPU has extracted the received byte, by reading the RXD register.
The TWI master read sequence is stopped by triggering the STOP task. This task must be triggered before
the last byte is extracted from RXD to ensure that the TWI master sends a NACK back to the slave before
generating the stop condition.
A typical TWI master read sequence is illustrated in The TWI master reading data from a slave on page
683. Occurrence 3 in this figure illustrates delayed processing of the RXDRDY event associated with RXD
byte B. In this scenario the TWI master will stretch the clock to prevent the slave from overwriting the
contents of the RXD register.

4413_417 v1.9 682

 Peripherals

START

READ

NACK
STOP
ACK

ACK

ACK

ACK
TWI ADDR A B M-1 M

BB

BB

BB

BB
TWI Lifeline

SHORT

SHORT

SHORT

SHORT
SUSPEND

SUSPEND

SUSPEND

STOP
SUSPENDED

STOPPED
RXDRDY
SUSPENDED

SUSPENDED

RXDRDY
RXDRDY

RXDRDY
CPU Lifeline

1 2 3 4 5

RESUME
M-1 = RXD
STARTRX

RESUME

M = RXD
A = RXD

Figure 170: The TWI master reading data from a slave

6.29.6 Master repeated start sequence

A typical repeated start sequence is one in which the TWI master writes one byte to the slave followed by
reading M bytes from the slave. Any combination and number of transmit and receive sequences can be
combined in this fashion. Only one shortcut to STOP can be enabled at any given time.
The following figure shows a repeated start sequence where the TWI master writes one byte, followed by
reading M bytes from the slave without performing a stop in-between.
START

START
WRITE

READ

NACK
STOP
ACK

ACK

ACK

ACK

ACK
TWI

ADDR 0 ADDR A M-1 M

BB

BB

BB
2-W Lifeline

SHORT

SHORT

SHORT
SUSPEND

SUSPEND

STOP
SUSPENDED

STOPPED
RXDRDY
TXDSENT

RXDRDY
CPU Lifeline

1 2 3 4 5
M-1 = RXD
STARTRX
STARTTX

RESUME

M = RXD
TXD = 0

Figure 171: Repeated start sequence illustration

4413_417 v1.9 683

 Peripherals

To generate a repeated start after a read sequence, a second start task, STARTRX or STARTTX, must be
triggered instead of the STOP task. This start task must be triggered before the last byte is extracted from
RXD to ensure that the TWI master sends a NACK back to the slave before generating the repeated start
condition.

6.29.7 Low power

When putting the system in low power and the peripheral is not needed, lowest possible power
consumption is achieved by stopping, and then disabling the peripheral.
The STOP task is not always needed, like when the peripheral is already stopped. If the STOP task is sent,
the software shall wait until the STOPPED event was received as a response before disabling the peripheral
through the ENABLE register.

6.29.8 Registers
Instances

Instance Base address Description

TWI0 0x40003000 Two-wire interface master 0

This instance is deprecated.

TWI1 0x40004000 Two-wire interface master 1

This instance is deprecated.

Register overview

Register Offset Description

TASKS_STARTRX 0x000 Start TWI receive sequence
TASKS_STARTTX 0x008 Start TWI transmit sequence
TASKS_STOP 0x014 Stop TWI transaction
TASKS_SUSPEND 0x01C Suspend TWI transaction
TASKS_RESUME 0x020 Resume TWI transaction
EVENTS_STOPPED 0x104 TWI stopped
EVENTS_RXDREADY 0x108 TWI RXD byte received
EVENTS_TXDSENT 0x11C TWI TXD byte sent
EVENTS_ERROR 0x124 TWI error
EVENTS_BB 0x138 TWI byte boundary, generated before each byte that is sent or received
EVENTS_SUSPENDED 0x148 TWI entered the suspended state
SHORTS 0x200 Shortcuts between local events and tasks
INTENSET 0x304 Enable interrupt
INTENCLR 0x308 Disable interrupt
ERRORSRC 0x4C4 Error source
ENABLE 0x500 Enable TWI
PSEL.SCL 0x508 Pin select for SCL
PSEL.SDA 0x50C Pin select for SDA
RXD 0x518 RXD register. Register is cleared on read and the buffer pointer will be modified if read.
TXD 0x51C TXD register
FREQUENCY 0x524 TWI frequency. Accuracy depends on the HFCLK source selected.
ADDRESS 0x588 Address used in the TWI transfer

6.29.8.1 TASKS_STARTRX
Address offset: 0x000

4413_417 v1.9 684

 Peripherals

Start TWI receive sequence

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A
Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STARTRX Start TWI receive sequence
Trigger 1 Trigger task

6.29.8.2 TASKS_STARTTX
Address offset: 0x008
Start TWI transmit sequence

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STARTTX Start TWI transmit sequence
Trigger 1 Trigger task

6.29.8.3 TASKS_STOP
Address offset: 0x014
Stop TWI transaction

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STOP Stop TWI transaction
Trigger 1 Trigger task

6.29.8.4 TASKS_SUSPEND
Address offset: 0x01C
Suspend TWI transaction

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_SUSPEND Suspend TWI transaction
Trigger 1 Trigger task

6.29.8.5 TASKS_RESUME
Address offset: 0x020
Resume TWI transaction

4413_417 v1.9 685

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_RESUME Resume TWI transaction
Trigger 1 Trigger task

6.29.8.6 EVENTS_STOPPED
Address offset: 0x104
TWI stopped

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_STOPPED TWI stopped
NotGenerated 0 Event not generated
Generated 1 Event generated

6.29.8.7 EVENTS_RXDREADY
Address offset: 0x108
TWI RXD byte received

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_RXDREADY TWI RXD byte received
NotGenerated 0 Event not generated
Generated 1 Event generated

6.29.8.8 EVENTS_TXDSENT
Address offset: 0x11C
TWI TXD byte sent

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_TXDSENT TWI TXD byte sent
NotGenerated 0 Event not generated
Generated 1 Event generated

6.29.8.9 EVENTS_ERROR
Address offset: 0x124
TWI error

4413_417 v1.9 686

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_ERROR TWI error
NotGenerated 0 Event not generated
Generated 1 Event generated

6.29.8.10 EVENTS_BB
Address offset: 0x138
TWI byte boundary, generated before each byte that is sent or received

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_BB TWI byte boundary, generated before each byte that is sent or received
NotGenerated 0 Event not generated
Generated 1 Event generated

6.29.8.11 EVENTS_SUSPENDED
Address offset: 0x148
TWI entered the suspended state
Generated just after ACK bit has been transferred in a read transaction, and only if SUSPEND has been
requested earlier.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_SUSPENDED TWI entered the suspended state

Generated just after ACK bit has been transferred in a read transaction, and
only if SUSPEND has been requested earlier.
NotGenerated 0 Event not generated
Generated 1 Event generated

6.29.8.12 SHORTS
Address offset: 0x200
Shortcuts between local events and tasks

4413_417 v1.9 687

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW BB_SUSPEND Shortcut between event BB and task SUSPEND
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
B RW BB_STOP Shortcut between event BB and task STOP
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut

6.29.8.13 INTENSET
Address offset: 0x304
Enable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW STOPPED Write '1' to enable interrupt for event STOPPED
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW RXDREADY Write '1' to enable interrupt for event RXDREADY
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW TXDSENT Write '1' to enable interrupt for event TXDSENT
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
D RW ERROR Write '1' to enable interrupt for event ERROR
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
E RW BB Write '1' to enable interrupt for event BB
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
F RW SUSPENDED Write '1' to enable interrupt for event SUSPENDED

Generated just after ACK bit has been transferred in a read transaction, and
only if SUSPEND has been requested earlier.
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.29.8.14 INTENCLR
Address offset: 0x308
Disable interrupt

4413_417 v1.9 688

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW STOPPED Write '1' to disable interrupt for event STOPPED
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW RXDREADY Write '1' to disable interrupt for event RXDREADY
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW TXDSENT Write '1' to disable interrupt for event TXDSENT
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
D RW ERROR Write '1' to disable interrupt for event ERROR
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
E RW BB Write '1' to disable interrupt for event BB
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
F RW SUSPENDED Write '1' to disable interrupt for event SUSPENDED

Generated just after ACK bit has been transferred in a read transaction, and
only if SUSPEND has been requested earlier.
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.29.8.15 ERRORSRC
Address offset: 0x4C4
Error source

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW OVERRUN Overrun error
W1C
A new byte was received before previous byte got read by software from
the RXD register. (Previous data is lost)
NotPresent 0 Read: no overrun occured
Present 1 Read: overrun occured
B RW ANACK NACK received after sending the address (write '1' to clear)
W1C
NotPresent 0 Read: error not present
Present 1 Read: error present
C RW DNACK NACK received after sending a data byte (write '1' to clear)
W1C
NotPresent 0 Read: error not present
Present 1 Read: error present

4413_417 v1.9 689

 Peripherals

6.29.8.16 ENABLE
Address offset: 0x500
Enable TWI

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW ENABLE Enable or disable TWI
Disabled 0 Disable TWI
Enabled 5 Enable TWI

6.29.8.17 PSEL.SCL
Address offset: 0x508
Pin select for SCL

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.29.8.18 PSEL.SDA
Address offset: 0x50C
Pin select for SDA

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.29.8.19 RXD
Address offset: 0x518
RXD register. Register is cleared on read and the buffer pointer will be modified if read.

4413_417 v1.9 690

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R RXD RXD register
RME

6.29.8.20 TXD
Address offset: 0x51C
TXD register

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TXD TXD register

6.29.8.21 FREQUENCY
Address offset: 0x524
TWI frequency. Accuracy depends on the HFCLK source selected.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x04000000 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW FREQUENCY TWI master clock frequency
K100 0x01980000 100 kbps
K250 0x04000000 250 kbps
K400 0x06680000 400 kbps (actual rate 410.256 kbps)

6.29.8.22 ADDRESS
Address offset: 0x588
Address used in the TWI transfer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW ADDRESS Address used in the TWI transfer

4413_417 v1.9 691

 Peripherals

6.29.9 Electrical specification

6.29.9.1 TWI interface electrical specifications

Symbol Description Min. Typ. Max. Units

fTWI,SCL Bit rates for TWI 39 100 400 kbps

tTWI,START Time from STARTRX/STARTTX task to transmission started 1.5 µs

6.29.9.2 Two Wire Interface (TWI) timing specifications

Symbol Description Min. Typ. Max. Units

tTWI,SU_DAT Data setup time before positive edge on SCL – all modes 300 ns
tTWI,HD_DAT Data hold time after negative edge on SCL – all modes 500 ns
tTWI,HD_STA,100kbps TWI master hold time for START and repeated START condition, 100 kbps 10000 ns
tTWI,HD_STA,250kbps TWI master hold time for START and repeated START condition, 250kbps 4000 ns
tTWI,HD_STA,400kbps TWI master hold time for START and repeated START condition, 400 kbps 2500 ns
tTWI,SU_STO,100kbps TWI master setup time from SCL high to STOP condition, 100 kbps 5000 ns
tTWI,SU_STO,250kbps TWI master setup time from SCL high to STOP condition, 250 kbps 2000 ns
tTWI,SU_STO,400kbps TWI master setup time from SCL high to STOP condition, 400 kbps 1250 ns
tTWI,BUF,100kbps TWI master bus free time between STOP and START conditions, 100 kbps 5800 ns
tTWI,BUF,250kbps TWI master bus free time between STOP and START conditions, 250 kbps 2700 ns
tTWI,BUF,400kbps TWI master bus free time between STOP and START conditions, 400 kbps 2100 ns

Figure 172: TWI timing diagram, 1 byte transaction

6.30 TIMER — Timer/counter

This peripheral is a general purpose timer designed to keep track of time in user-selective time intervals, it
can operate in two modes: timer and counter.

39
High bit rates or stronger pull-ups may require GPIOs to be set as High Drive, see GPIO chapter for
more details.

4413_417 v1.9 692

 Peripherals

CAPTURE[0..n]
COUNT

START

CLEAR
STOP
TIMER

TIMER Core

Increment BITMODE

PCLK1M Counter
Prescaler
PCLK16M fTIMER
CC[0..n]

PRESCALER MODE

COMPARE[0..n]
Figure 173: Block schematic for timer/counter

The timer/counter runs on the high-frequency clock source (HFCLK) and includes a four-bit (1/2X)
prescaler that can divide the timer input clock from the HFCLK controller. Clock source selection between
PCLK16M and PCLK1M is automatic according to TIMER base frequency set by the prescaler. The TIMER
base frequency is always given as 16 MHz divided by the prescaler value.
The PPI system allows a TIMER event to trigger a task of any other system peripheral of the device. The PPI
system also enables the TIMER task/event features to generate periodic output and PWM signals to any
GPIO. The number of input/outputs used at the same time is limited by the number of GPIOTE channels.
TIMER can operate in two modes: Timer mode and Counter mode. In both modes, TIMER is started by
triggering the START task, and stopped by triggering the STOP task. After the timer is stopped the timer
can resume timing/counting by triggering the START task again. When timing/counting is resumed, the
timer will continue from the value it had prior to being stopped.
In Timer mode, the TIMER's internal Counter register is incremented by one for every tick of the timer
frequency fTIMER as illustrated in Block schematic for timer/counter on page 693. The timer frequency
is derived from PCLK16M as shown in the following example, using the values specified in the PRESCALER
register.

fTIMER = 16 MHz / (2PRESCALER)

When fTIMER ≤ 1 MHz, TIMER will use PCLK1M instead of PCLK16M for reduced power consumption.
In counter mode, the TIMER's internal Counter register is incremented by one each time the COUNT task
is triggered, meaning the timer frequency and the prescaler are not utilized in counter mode. Similarly, the
COUNT task has no effect in Timer mode.
The TIMER's maximum value is configured by changing the bit-width of the timer in register BITMODE on
page 702.
PRESCALER on page 702 and BITMODE on page 702 must only be updated when the timer is stopped.
If these registers are updated while the timer is started, unpredictable behavior may occur.
When the timer is incremented beyond its maximum value, the Counter register will overflow and the
timer will automatically start over from zero.

4413_417 v1.9 693

 Peripherals

The Counter register can be cleared by triggering the CLEAR task. This will explicitly set the internal value
to zero.
TIMER implements multiple capture/compare registers.
Independent of prescaler setting, the accuracy of TIMER is equivalent to one tick of the timer frequency
fTIMER as illustrated in Block schematic for timer/counter on page 693.

6.30.1 Capture
TIMER implements one capture task for every available capture/compare register.
Every time the CAPTURE[n] task is triggered, the Counter value is copied to the CC[n] register.

6.30.2 Compare
TIMER implements one COMPARE event for every available capture/compare register.
A COMPARE event is generated when the Counter is incremented and then becomes equal to the
value specified in one of the capture compare registers. When the Counter value becomes equal to the
value specified in a capture compare register CC[n], the corresponding compare event COMPARE[n] is
generated.
BITMODE on page 702 specifies how many bits of the Counter register and the capture/compare
register that are used when the comparison is performed. Other bits will be ignored.

6.30.3 Task delays

After TIMER is started, the CLEAR, COUNT, and STOP tasks are guaranteed to take effect within one clock
cycle of the PCLK16M.

6.30.4 Task priority

If the START task and the STOP task are triggered at the same time, meaning within the same period of
PCLK16M, the STOP task will be prioritized.

6.30.5 Registers
Instances

Instance Base address Description

TIMER0 0x40008000 Timer 0
TIMER1 0x40009000 Timer 1
TIMER2 0x4000A000 Timer 2
TIMER3 0x4001A000 Timer 3
TIMER4 0x4001B000 Timer 4

Configuration

Instance Configuration
TIMER0 This timer instance has 4 CC registers (CC[0..3])
TIMER1 This timer instance has 4 CC registers (CC[0..3])
TIMER2 This timer instance has 4 CC registers (CC[0..3])
TIMER3 This timer instance has 6 CC registers (CC[0..5])
TIMER4 This timer instance has 6 CC registers (CC[0..5])

4413_417 v1.9 694

 Peripherals

Register overview

Register Offset Description

TASKS_START 0x000 Start Timer
TASKS_STOP 0x004 Stop Timer
TASKS_COUNT 0x008 Increment Timer (Counter mode only)
TASKS_CLEAR 0x00C Clear time
TASKS_SHUTDOWN 0x010 Shut down timer

This register is deprecated.

TASKS_CAPTURE[0] 0x040 Capture Timer value to CC[0] register
TASKS_CAPTURE[1] 0x044 Capture Timer value to CC[1] register
TASKS_CAPTURE[2] 0x048 Capture Timer value to CC[2] register
TASKS_CAPTURE[3] 0x04C Capture Timer value to CC[3] register
TASKS_CAPTURE[4] 0x050 Capture Timer value to CC[4] register
TASKS_CAPTURE[5] 0x054 Capture Timer value to CC[5] register
EVENTS_COMPARE[0] 0x140 Compare event on CC[0] match
EVENTS_COMPARE[1] 0x144 Compare event on CC[1] match
EVENTS_COMPARE[2] 0x148 Compare event on CC[2] match
EVENTS_COMPARE[3] 0x14C Compare event on CC[3] match
EVENTS_COMPARE[4] 0x150 Compare event on CC[4] match
EVENTS_COMPARE[5] 0x154 Compare event on CC[5] match
SHORTS 0x200 Shortcuts between local events and tasks
INTENSET 0x304 Enable interrupt
INTENCLR 0x308 Disable interrupt
MODE 0x504 Timer mode selection
BITMODE 0x508 Configure the number of bits used by the TIMER
PRESCALER 0x510 Timer prescaler register
CC[0] 0x540 Capture/Compare register 0
CC[1] 0x544 Capture/Compare register 1
CC[2] 0x548 Capture/Compare register 2
CC[3] 0x54C Capture/Compare register 3
CC[4] 0x550 Capture/Compare register 4
CC[5] 0x554 Capture/Compare register 5

6.30.5.1 TASKS_START
Address offset: 0x000
Start Timer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_START Start Timer
Trigger 1 Trigger task

6.30.5.2 TASKS_STOP
Address offset: 0x004
Stop Timer

4413_417 v1.9 695

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STOP Stop Timer
Trigger 1 Trigger task

6.30.5.3 TASKS_COUNT
Address offset: 0x008
Increment Timer (Counter mode only)

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_COUNT Increment Timer (Counter mode only)
Trigger 1 Trigger task

6.30.5.4 TASKS_CLEAR
Address offset: 0x00C
Clear time

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_CLEAR Clear time
Trigger 1 Trigger task

6.30.5.5 TASKS_SHUTDOWN (Deprecated)

Address offset: 0x010
Shut down timer
This register is deprecated.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_SHUTDOWN Shut down timer

This field is deprecated.

Trigger 1 Trigger task

6.30.5.6 TASKS_CAPTURE[0]
Address offset: 0x040
Capture Timer value to CC[0] register

4413_417 v1.9 696

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_CAPTURE Capture Timer value to CC[0] register
Trigger 1 Trigger task

6.30.5.7 TASKS_CAPTURE[1]
Address offset: 0x044
Capture Timer value to CC[1] register

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_CAPTURE Capture Timer value to CC[1] register
Trigger 1 Trigger task

6.30.5.8 TASKS_CAPTURE[2]
Address offset: 0x048
Capture Timer value to CC[2] register

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_CAPTURE Capture Timer value to CC[2] register
Trigger 1 Trigger task

6.30.5.9 TASKS_CAPTURE[3]
Address offset: 0x04C
Capture Timer value to CC[3] register

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_CAPTURE Capture Timer value to CC[3] register
Trigger 1 Trigger task

6.30.5.10 TASKS_CAPTURE[4]
Address offset: 0x050
Capture Timer value to CC[4] register

4413_417 v1.9 697

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_CAPTURE Capture Timer value to CC[4] register
Trigger 1 Trigger task

6.30.5.11 TASKS_CAPTURE[5]
Address offset: 0x054
Capture Timer value to CC[5] register

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_CAPTURE Capture Timer value to CC[5] register
Trigger 1 Trigger task

6.30.5.12 EVENTS_COMPARE[0]
Address offset: 0x140
Compare event on CC[0] match

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_COMPARE Compare event on CC[0] match
NotGenerated 0 Event not generated
Generated 1 Event generated

6.30.5.13 EVENTS_COMPARE[1]
Address offset: 0x144
Compare event on CC[1] match

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_COMPARE Compare event on CC[1] match
NotGenerated 0 Event not generated
Generated 1 Event generated

6.30.5.14 EVENTS_COMPARE[2]
Address offset: 0x148
Compare event on CC[2] match

4413_417 v1.9 698

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_COMPARE Compare event on CC[2] match
NotGenerated 0 Event not generated
Generated 1 Event generated

6.30.5.15 EVENTS_COMPARE[3]
Address offset: 0x14C
Compare event on CC[3] match

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_COMPARE Compare event on CC[3] match
NotGenerated 0 Event not generated
Generated 1 Event generated

6.30.5.16 EVENTS_COMPARE[4]
Address offset: 0x150
Compare event on CC[4] match

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_COMPARE Compare event on CC[4] match
NotGenerated 0 Event not generated
Generated 1 Event generated

6.30.5.17 EVENTS_COMPARE[5]
Address offset: 0x154
Compare event on CC[5] match

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_COMPARE Compare event on CC[5] match
NotGenerated 0 Event not generated
Generated 1 Event generated

6.30.5.18 SHORTS
Address offset: 0x200
Shortcuts between local events and tasks

4413_417 v1.9 699

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW COMPARE0_CLEAR Shortcut between event COMPARE[0] and task CLEAR
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
B RW COMPARE1_CLEAR Shortcut between event COMPARE[1] and task CLEAR
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
C RW COMPARE2_CLEAR Shortcut between event COMPARE[2] and task CLEAR
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
D RW COMPARE3_CLEAR Shortcut between event COMPARE[3] and task CLEAR
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
E RW COMPARE4_CLEAR Shortcut between event COMPARE[4] and task CLEAR
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
F RW COMPARE5_CLEAR Shortcut between event COMPARE[5] and task CLEAR
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
G RW COMPARE0_STOP Shortcut between event COMPARE[0] and task STOP
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
H RW COMPARE1_STOP Shortcut between event COMPARE[1] and task STOP
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
I RW COMPARE2_STOP Shortcut between event COMPARE[2] and task STOP
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
J RW COMPARE3_STOP Shortcut between event COMPARE[3] and task STOP
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
K RW COMPARE4_STOP Shortcut between event COMPARE[4] and task STOP
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
L RW COMPARE5_STOP Shortcut between event COMPARE[5] and task STOP
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut

6.30.5.19 INTENSET
Address offset: 0x304
Enable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW COMPARE[0] Write '1' to enable interrupt for event COMPARE[0]
Set 1 Enable
Disabled 0 Read: Disabled

4413_417 v1.9 700

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Enabled 1 Read: Enabled
B RW COMPARE[1] Write '1' to enable interrupt for event COMPARE[1]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW COMPARE[2] Write '1' to enable interrupt for event COMPARE[2]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
D RW COMPARE[3] Write '1' to enable interrupt for event COMPARE[3]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
E RW COMPARE[4] Write '1' to enable interrupt for event COMPARE[4]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
F RW COMPARE[5] Write '1' to enable interrupt for event COMPARE[5]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.30.5.20 INTENCLR
Address offset: 0x308
Disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW COMPARE[0] Write '1' to disable interrupt for event COMPARE[0]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW COMPARE[1] Write '1' to disable interrupt for event COMPARE[1]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW COMPARE[2] Write '1' to disable interrupt for event COMPARE[2]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
D RW COMPARE[3] Write '1' to disable interrupt for event COMPARE[3]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
E RW COMPARE[4] Write '1' to disable interrupt for event COMPARE[4]
Clear 1 Disable

4413_417 v1.9 701

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
F RW COMPARE[5] Write '1' to disable interrupt for event COMPARE[5]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.30.5.21 MODE
Address offset: 0x504
Timer mode selection

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW MODE Timer mode
Timer 0 Select Timer mode
Counter 1 Select Counter mode

This enumerator is deprecated.

LowPowerCounter 2 Select Low Power Counter mode

6.30.5.22 BITMODE
Address offset: 0x508
Configure the number of bits used by the TIMER

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW BITMODE Timer bit width
16Bit 0 16 bit timer bit width
08Bit 1 8 bit timer bit width
24Bit 2 24 bit timer bit width
32Bit 3 32 bit timer bit width

6.30.5.23 PRESCALER
Address offset: 0x510
Timer prescaler register

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A

Reset 0x00000004 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0
ID R/W Field Value ID Value Description
A RW PRESCALER [0..9] Prescaler value

4413_417 v1.9 702

 Peripherals

6.30.5.24 CC[0]
Address offset: 0x540
Capture/Compare register 0

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW CC Capture/Compare value

Only the number of bits indicated by BITMODE will be used by the TIMER.

6.30.5.25 CC[1]
Address offset: 0x544
Capture/Compare register 1

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW CC Capture/Compare value

Only the number of bits indicated by BITMODE will be used by the TIMER.

6.30.5.26 CC[2]
Address offset: 0x548
Capture/Compare register 2

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW CC Capture/Compare value

Only the number of bits indicated by BITMODE will be used by the TIMER.

6.30.5.27 CC[3]
Address offset: 0x54C
Capture/Compare register 3

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW CC Capture/Compare value

Only the number of bits indicated by BITMODE will be used by the TIMER.

4413_417 v1.9 703

 Peripherals

6.30.5.28 CC[4]
Address offset: 0x550
Capture/Compare register 4

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW CC Capture/Compare value

Only the number of bits indicated by BITMODE will be used by the TIMER.

6.30.5.29 CC[5]
Address offset: 0x554
Capture/Compare register 5

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW CC Capture/Compare value

Only the number of bits indicated by BITMODE will be used by the TIMER.

6.31 TWIM — I2C compatible two-wire interface master

with EasyDMA
TWI master with EasyDMA (TWIM) is a two-wire half-duplex master which can communicate with multiple
slave devices connected to the same bus.
Listed here are the main features for TWIM:
• I2C compatible
• Supported baud rates: 100, 250, 400 kbps
• Support for clock stretching (non I2C compliant)
• EasyDMA
The two-wire interface can communicate with a bi-directional wired-AND bus with two lines (SCL, SDA).
The protocol makes it possible to interconnect up to 127 individually addressable devices. TWIM is not
compatible with CBUS.
The GPIOs used for each two-wire interface line can be chosen from any GPIO on the device and are
independently configurable. This enables great flexibility in device pinout and efficient use of board space
and signal routing.

4413_417 v1.9 704

 Peripherals

SUSPEND
STARTRX
STARTTX

RESUME

STOP
TWIM
GPIO RAM

PSEL.SDA TXD.PTR
buffer[0]
buffer[1] TXD buffer
TXD+1 EasyDMA buffer[TXD.MAXCNT-1]

SDA Pin

RXD-1 EasyDMA buffer[0]

SCL Pin buffer[1]
RXD buffer
PSEL.SCL RXD.PTR
buffer[RXD.MAXCNT-1]

SUSPENDED
RXSTARTED
TXSTARTED

ERROR
LASTRX
LASTTX

STOPPED

Figure 174: TWI master with EasyDMA

A typical TWI setup consists of one master and one or more slaves. For an example, see the following
figure. This TWIM is only able to operate as a single master on the TWI bus. Multi-master bus
configuration is not supported.
VDD VDD
TWI slave TWI slave TWI slave
TWI master (EEPROM) (Sensor)
(TWIM)
Address = b1011001 Address = b1011000 Address = b1011011
R R
SDA SCL SCL SDA SCL SDA SCL SDA

Figure 175: A typical TWI setup comprising one master and three slaves

This TWI master supports clock stretching performed by the slaves. The SCK pulse following a stretched
clock cycle may be shorter than specified by the I2C specification.
The TWI master is started by triggering the STARTTX or STARTRX tasks, and stopped by triggering the STOP
task. The TWI master will generate a STOPPED event when it has stopped following a STOP task.
After the TWI master is started, the STARTTX or STARTRX tasks should not be triggered again until the TWI
master has issued a LASTRX, LASTTX, or STOPPED event.
The TWI master can be suspended using the SUSPEND task, this can be used when using the TWI master
in a low priority interrupt context. When the TWIM enters suspend state, will automatically issue a
SUSPENDED event while performing a continuous clock stretching until it is instructed to resume operation
via a RESUME task. The TWI master cannot be stopped while it is suspended, thus the STOP task has to be
issued after the TWI master has been resumed.

Note: Any ongoing byte transfer will be allowed to complete before the suspend is enforced. A
SUSPEND task has no effect unless the TWI master is actively involved in a transfer.

If a NACK is clocked in from the slave, the TWI master will generate an ERROR event.

4413_417 v1.9 705

 Peripherals

6.31.1 EasyDMA
The TWIM implements EasyDMA for accessing RAM without CPU involvement.
The TWIM peripheral implements the EasyDMA channels found in the following table.

Channel Type Register Cluster

TXD READER TXD
RXD WRITER RXD

Table 51: TWIM EasyDMA Channels

For detailed information regarding the use of EasyDMA, see EasyDMA on page 62.
The .PTR and .MAXCNT registers are double-buffered. They can be updated and prepared for the next RX/
TX transmission immediately after having received the RXSTARTED/TXSTARTED event.
The STOPPED event indicates that EasyDMA has finished accessing the buffer in RAM.

6.31.2 Master write sequence

A TWI master write sequence is started by triggering the STARTTX task. After the STARTTX task has been
triggered, the TWI master will generate a start condition on the TWI bus, followed by clocking out the
address and the READ/WRITE bit set to 0 (WRITE=0, READ=1).
The address must match the address of the slave device that the master wants to write to. The READ/
WRITE bit is followed by an ACK/NACK bit (ACK=0 or NACK=1) generated by the slave.
After receiving the ACK bit, the TWI master will clock out the data bytes found in the transmit buffer
located in RAM at the address specified in the TXD.PTR register. Each byte clocked out from the master will
be followed by an ACK/NACK bit clocked in from the slave.
A typical TWI master write sequence is shown in the following figure. Occurrence 2 in the figure illustrates
clock stretching performed by the TWI master following a SUSPEND task.
A SUSPENDED event indicates that the SUSPEND task has taken effect. This event can be used to
synchronize the software.
The TWI master will generate a LASTTX event when it starts to transmit the last byte, this is shown in the
following figure.

Stretch
START

WRITE

STOP
ACK

ACK

ACK

ACK

ACK

ACK
TWI

ADDR 0 1 2 N-1 N
SUSPENDED

STOPPED
LASTTX
CPU Lifeline

1 2 3 4
TXD.MAXCNT = N+1

STARTTX

RESUME
SUSPEND

STOP

Figure 176: TWI master writing data to a slave

4413_417 v1.9 706

 Peripherals

The TWI master is stopped by triggering the STOP task. This task should be triggered during the
transmission of the last byte to secure that the TWI master will stop as fast as possible after sending the
last byte. The shortcut between LASTTX and STOP can alternatively be used to accomplish this.

Note: The TWI master does not stop by itself when the entire RAM buffer has been sent, or when
an error occurs. The STOP task must be issued, through the use of a local or PPI shortcut, or in
software as part of the error handler.

6.31.3 Master read sequence

A TWI master read sequence is started by triggering the STARTRX task. After the STARTRX task has been
triggered, the TWI master will generate a start condition on the TWI bus, followed by clocking out the
address and the READ/WRITE bit set to 1 (WRITE = 0, READ = 1). The address must match the address of
the slave device that the master wants to read from. The READ/WRITE bit is followed by an ACK/NACK bit
(ACK=0 or NACK = 1) generated by the slave.
After sending the ACK bit, the TWI slave will send data to the master using the clock generated by the
master.
Data received will be stored in RAM at the address specified in the RXD.PTR register. The TWI master
will generate an ACK after all but the last byte have been received from the slave. The TWI master will
generate a NACK after the last byte received to indicate that the read sequence shall stop.
A typical TWI master read sequence is illustrated in The TWI master reading data from a slave on page
708. Occurrence 2 in the figure illustrates clock stretching performed by the TWI master following a
SUSPEND task.
A SUSPENDED event indicates that the SUSPEND task has taken effect. This event can be used to
synchronize the software.
The TWI master will generate a LASTRX event when it is ready to receive the last byte, as shown in The
TWI master reading data from a slave on page 708. If RXD.MAXCNT > 1, the LASTRX event is generated
after sending the ACK of the previously received byte. If RXD.MAXCNT = 1, the LASTRX event is generated
after receiving the ACK following the address and READ bit.
The TWI master is stopped by triggering the STOP task. This task must be triggered before the NACK bit is
supposed to be transmitted. The STOP task can be triggered at any time during the reception of the last
byte. It is recommended to use the shortcut between LASTRX and STOP to accomplish this.
The TWI master does not stop by itself when the RAM buffer is full, or when an error occurs. The STOP
task must be issued, through the use of a local or PPI shortcut, or in software as part of the error handler.
The TWI master cannot be stopped while suspended, so the STOP task must be issued after the TWI
master has been resumed.

4413_417 v1.9 707

 Peripherals

START
Stretch

READ

NACK
STOP
ACK

ACK

ACK

ACK

ACK
TWI
ADDR 0 1 2 M-1 M

SUSPENDED

STOPPED
LASTRX
CPU Lifeline

1 2 3 4
RXD.MAXCNT = M+1

STARTRX

RESUME
SUSPEND

STOP
Figure 177: The TWI master reading data from a slave

6.31.4 Master repeated start sequence

A typical repeated start sequence is one in which the TWI master writes two bytes to the slave followed by
reading four bytes from the slave. This example uses shortcuts to perform the simplest type of repeated
start sequence, i.e. one write followed by one read. The same approach can be used to perform a
repeated start sequence where the sequence is read followed by write.
The following figure shows an example of a repeated start sequence where the TWI master writes two
bytes followed by reading four bytes from the slave.
CPU Lifeline

RESTART
START

WRITE

READ

NACK
STOP
ACK

ACK

ACK
ACK

ACK

ACK

ACK
ADDR 0 1 ADDR 0 1 2 3

STOPPED
LASTTX

LASTRX
CPU Lifeline

1 2
TXD.MAXCNT = 2
RXD.MAXCNT = 4

STARTTX

STARTRX

STOP

Figure 178: Master repeated start sequence

If a more complex repeated start sequence is needed, and the TWI firmware drive is serviced in a low
priority interrupt, it may be necessary to use the SUSPEND task and SUSPENDED event to guarantee that
the correct tasks are generated at the correct time. A double repeated start sequence using the SUSPEND
task to secure safe operation in low priority interrupts is shown in the following figure.

4413_417 v1.9 708

 Peripherals

RESTART

RESTART
START

WRITE

WRITE
READ

NACK

STOP
Stretch

TWI

ACK

ACK

ACK

ACK

ACK

ACK
ADDR 0 ADDR 0 ADDR 0 1

STOPPED
LASTTX

SUSPENDED

LASTRX

LASTTX
CPU Lifeline

1 2 3 4 5
TXD.MAXCNT = 1

RXD.MAXCNT = 1

TXD.MAXCNT = 2
STARTTX

SUSPEND

STARTRX

RESUME

STOP
STARTTX
Figure 179: Double repeated start sequence

6.31.5 Low power

When putting the system in low power and the peripheral is not needed, lowest possible power
consumption is achieved by stopping, and then disabling the peripheral.
When the STOP task is sent, the software shall wait until the STOPPED event is received as a response
before disabling the peripheral through the ENABLE register. If the peripheral is already stopped, the STOP
task is not required.

6.31.6 Master mode pin configuration

The SCL and SDA signals associated with the TWI master are mapped to physical pins according to the
configuration specified in the PSEL.SCL and PSEL.SDA registers respectively.
The PSEL.SCL and PSEL.SDA registers and their configurations are only used as long as the TWI master is
enabled, and retained only as long as the device is in ON mode. When the peripheral is disabled, the pins
will behave as regular GPIOs, and use the configuration in their respective OUT bit field and PIN_CNF[n]
register. PSEL.SCL, PSEL.SDA must only be configured when the TWI master is disabled.
To secure correct signal levels on the pins used by the TWI master when the system is in OFF mode, and
when the TWI master is disabled, these pins must be configured in the GPIO peripheral as described in the
following table.
Only one peripheral can be assigned to drive a particular GPIO pin at a time. Failing to do so may result in
unpredictable behavior.

TWI master signal TWI master pin Direction Output value Drive strength

SCL As specified in PSEL.SCL Input Not applicable S0D1

SDA As specified in PSEL.SDA Input Not applicable S0D1

Table 52: GPIO configuration before enabling peripheral

6.31.7 Registers
Instances

Instance Base address Description

TWIM0 0x40003000 Two-wire interface master 0
TWIM1 0x40004000 Two-wire interface master 1

4413_417 v1.9 709

 Peripherals

Register overview

Register Offset Description

TASKS_STARTRX 0x000 Start TWI receive sequence
TASKS_STARTTX 0x008 Start TWI transmit sequence
TASKS_STOP 0x014 Stop TWI transaction. Must be issued while the TWI master is not suspended.
TASKS_SUSPEND 0x01C Suspend TWI transaction
TASKS_RESUME 0x020 Resume TWI transaction
EVENTS_STOPPED 0x104 TWI stopped
EVENTS_ERROR 0x124 TWI error
EVENTS_SUSPENDED 0x148 SUSPEND task has been issued, TWI traffic is now suspended.
EVENTS_RXSTARTED 0x14C Receive sequence started
EVENTS_TXSTARTED 0x150 Transmit sequence started
EVENTS_LASTRX 0x15C Byte boundary, starting to receive the last byte
EVENTS_LASTTX 0x160 Byte boundary, starting to transmit the last byte
SHORTS 0x200 Shortcuts between local events and tasks
INTEN 0x300 Enable or disable interrupt
INTENSET 0x304 Enable interrupt
INTENCLR 0x308 Disable interrupt
ERRORSRC 0x4C4 Error source
ENABLE 0x500 Enable TWIM
PSEL.SCL 0x508 Pin select for SCL signal
PSEL.SDA 0x50C Pin select for SDA signal
FREQUENCY 0x524 TWI frequency. Accuracy depends on the HFCLK source selected.
RXD.PTR 0x534 Data pointer
RXD.MAXCNT 0x538 Maximum number of bytes in receive buffer
RXD.AMOUNT 0x53C Number of bytes transferred in the last transaction
RXD.LIST 0x540 EasyDMA list type
TXD.PTR 0x544 Data pointer
TXD.MAXCNT 0x548 Maximum number of bytes in transmit buffer
TXD.AMOUNT 0x54C Number of bytes transferred in the last transaction
TXD.LIST 0x550 EasyDMA list type
ADDRESS 0x588 Address used in the TWI transfer

6.31.7.1 TASKS_STARTRX
Address offset: 0x000
Start TWI receive sequence

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STARTRX Start TWI receive sequence
Trigger 1 Trigger task

6.31.7.2 TASKS_STARTTX
Address offset: 0x008
Start TWI transmit sequence

4413_417 v1.9 710

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STARTTX Start TWI transmit sequence
Trigger 1 Trigger task

6.31.7.3 TASKS_STOP
Address offset: 0x014
Stop TWI transaction. Must be issued while the TWI master is not suspended.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STOP Stop TWI transaction. Must be issued while the TWI master is not
suspended.
Trigger 1 Trigger task

6.31.7.4 TASKS_SUSPEND
Address offset: 0x01C
Suspend TWI transaction

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_SUSPEND Suspend TWI transaction
Trigger 1 Trigger task

6.31.7.5 TASKS_RESUME
Address offset: 0x020
Resume TWI transaction

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_RESUME Resume TWI transaction
Trigger 1 Trigger task

6.31.7.6 EVENTS_STOPPED
Address offset: 0x104
TWI stopped

4413_417 v1.9 711

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_STOPPED TWI stopped
NotGenerated 0 Event not generated
Generated 1 Event generated

6.31.7.7 EVENTS_ERROR
Address offset: 0x124
TWI error

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_ERROR TWI error
NotGenerated 0 Event not generated
Generated 1 Event generated

6.31.7.8 EVENTS_SUSPENDED
Address offset: 0x148
SUSPEND task has been issued, TWI traffic is now suspended.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_SUSPENDED SUSPEND task has been issued, TWI traffic is now suspended.
NotGenerated 0 Event not generated
Generated 1 Event generated

6.31.7.9 EVENTS_RXSTARTED
Address offset: 0x14C
Receive sequence started

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_RXSTARTED Receive sequence started
NotGenerated 0 Event not generated
Generated 1 Event generated

6.31.7.10 EVENTS_TXSTARTED
Address offset: 0x150
Transmit sequence started

4413_417 v1.9 712

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_TXSTARTED Transmit sequence started
NotGenerated 0 Event not generated
Generated 1 Event generated

6.31.7.11 EVENTS_LASTRX
Address offset: 0x15C
Byte boundary, starting to receive the last byte

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_LASTRX Byte boundary, starting to receive the last byte
NotGenerated 0 Event not generated
Generated 1 Event generated

6.31.7.12 EVENTS_LASTTX
Address offset: 0x160
Byte boundary, starting to transmit the last byte

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_LASTTX Byte boundary, starting to transmit the last byte
NotGenerated 0 Event not generated
Generated 1 Event generated

6.31.7.13 SHORTS
Address offset: 0x200
Shortcuts between local events and tasks

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW LASTTX_STARTRX Shortcut between event LASTTX and task STARTRX
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
B RW LASTTX_SUSPEND Shortcut between event LASTTX and task SUSPEND
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
C RW LASTTX_STOP Shortcut between event LASTTX and task STOP
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut

4413_417 v1.9 713

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
D RW LASTRX_STARTTX Shortcut between event LASTRX and task STARTTX
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
E RW LASTRX_SUSPEND Shortcut between event LASTRX and task SUSPEND
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
F RW LASTRX_STOP Shortcut between event LASTRX and task STOP
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut

6.31.7.14 INTEN
Address offset: 0x300
Enable or disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID J I H G F D A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW STOPPED Enable or disable interrupt for event STOPPED
Disabled 0 Disable
Enabled 1 Enable
D RW ERROR Enable or disable interrupt for event ERROR
Disabled 0 Disable
Enabled 1 Enable
F RW SUSPENDED Enable or disable interrupt for event SUSPENDED
Disabled 0 Disable
Enabled 1 Enable
G RW RXSTARTED Enable or disable interrupt for event RXSTARTED
Disabled 0 Disable
Enabled 1 Enable
H RW TXSTARTED Enable or disable interrupt for event TXSTARTED
Disabled 0 Disable
Enabled 1 Enable
I RW LASTRX Enable or disable interrupt for event LASTRX
Disabled 0 Disable
Enabled 1 Enable
J RW LASTTX Enable or disable interrupt for event LASTTX
Disabled 0 Disable
Enabled 1 Enable

6.31.7.15 INTENSET
Address offset: 0x304
Enable interrupt

4413_417 v1.9 714

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID J I H G F D A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW STOPPED Write '1' to enable interrupt for event STOPPED
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
D RW ERROR Write '1' to enable interrupt for event ERROR
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
F RW SUSPENDED Write '1' to enable interrupt for event SUSPENDED
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
G RW RXSTARTED Write '1' to enable interrupt for event RXSTARTED
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
H RW TXSTARTED Write '1' to enable interrupt for event TXSTARTED
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
I RW LASTRX Write '1' to enable interrupt for event LASTRX
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
J RW LASTTX Write '1' to enable interrupt for event LASTTX
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.31.7.16 INTENCLR
Address offset: 0x308
Disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID J I H G F D A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW STOPPED Write '1' to disable interrupt for event STOPPED
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
D RW ERROR Write '1' to disable interrupt for event ERROR
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
F RW SUSPENDED Write '1' to disable interrupt for event SUSPENDED
Clear 1 Disable
Disabled 0 Read: Disabled

4413_417 v1.9 715

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID J I H G F D A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Enabled 1 Read: Enabled
G RW RXSTARTED Write '1' to disable interrupt for event RXSTARTED
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
H RW TXSTARTED Write '1' to disable interrupt for event TXSTARTED
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
I RW LASTRX Write '1' to disable interrupt for event LASTRX
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
J RW LASTTX Write '1' to disable interrupt for event LASTTX
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.31.7.17 ERRORSRC
Address offset: 0x4C4
Error source

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW OVERRUN Overrun error
W1C
A new byte was received before previous byte got transferred into RXD
buffer. (Previous data is lost)
NotReceived 0 Error did not occur
Received 1 Error occurred
B RW ANACK NACK received after sending the address (write '1' to clear)
W1C
NotReceived 0 Error did not occur
Received 1 Error occurred
C RW DNACK NACK received after sending a data byte (write '1' to clear)
W1C
NotReceived 0 Error did not occur
Received 1 Error occurred

6.31.7.18 ENABLE
Address offset: 0x500
Enable TWIM

4413_417 v1.9 716

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW ENABLE Enable or disable TWIM
Disabled 0 Disable TWIM
Enabled 6 Enable TWIM

6.31.7.19 PSEL.SCL
Address offset: 0x508
Pin select for SCL signal

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.31.7.20 PSEL.SDA
Address offset: 0x50C
Pin select for SDA signal

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.31.7.21 FREQUENCY
Address offset: 0x524
TWI frequency. Accuracy depends on the HFCLK source selected.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x04000000 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW FREQUENCY TWI master clock frequency
K100 0x01980000 100 kbps
K250 0x04000000 250 kbps
K400 0x06400000 400 kbps

4413_417 v1.9 717

 Peripherals

6.31.7.22 RXD
RXD EasyDMA channel

6.31.7.22.1 RXD.PTR
Address offset: 0x534
Data pointer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PTR Data pointer

See the memory chapter for details about which memories are available for
EasyDMA.

6.31.7.22.2 RXD.MAXCNT
Address offset: 0x538
Maximum number of bytes in receive buffer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW MAXCNT [0..0xFFFF] Maximum number of bytes in receive buffer

6.31.7.22.3 RXD.AMOUNT
Address offset: 0x53C
Number of bytes transferred in the last transaction

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R AMOUNT [0..0xFFFF] Number of bytes transferred in the last transaction. In case of NACK error,
includes the NACK'ed byte.

6.31.7.22.4 RXD.LIST
Address offset: 0x540
EasyDMA list type

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW LIST List type
Disabled 0 Disable EasyDMA list
ArrayList 1 Use array list

4413_417 v1.9 718

 Peripherals

6.31.7.23 TXD
TXD EasyDMA channel

6.31.7.23.1 TXD.PTR
Address offset: 0x544
Data pointer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PTR Data pointer

See the memory chapter for details about which memories are available for
EasyDMA.

6.31.7.23.2 TXD.MAXCNT
Address offset: 0x548
Maximum number of bytes in transmit buffer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW MAXCNT [0..0xFFFF] Maximum number of bytes in transmit buffer

6.31.7.23.3 TXD.AMOUNT
Address offset: 0x54C
Number of bytes transferred in the last transaction

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R AMOUNT [0..0xFFFF] Number of bytes transferred in the last transaction. In case of NACK error,
includes the NACK'ed byte.

6.31.7.23.4 TXD.LIST
Address offset: 0x550
EasyDMA list type

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW LIST List type
Disabled 0 Disable EasyDMA list
ArrayList 1 Use array list

4413_417 v1.9 719

 Peripherals

6.31.7.24 ADDRESS
Address offset: 0x588
Address used in the TWI transfer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW ADDRESS Address used in the TWI transfer

6.31.8 Electrical specification

6.31.8.1 TWIM interface electrical specifications

Symbol Description Min. Typ. Max. Units

fTWIM,SCL Bit rates for TWIM 40 100 400 kbps

tTWIM,START Time from STARTRX/STARTTX task to transmission started 1.5 µs

6.31.8.2 Two Wire Interface Master (TWIM) timing specifications

Symbol Description Min. Typ. Max. Units

tTWIM,SU_DAT Data setup time before positive edge on SCL – all modes 300 ns
tTWIM,HD_DAT Data hold time after negative edge on SCL – 100, 250 and 400 kbps 500 ns
tTWIM,HD_STA,100kbps TWIM master hold time for START and repeated START condition, 100 kbps 9937.5 ns
tTWIM,HD_STA,250kbps TWIM master hold time for START and repeated START condition, 250 kbps 3937.5 ns
tTWIM,HD_STA,400kbps TWIM master hold time for START and repeated START condition, 400 kbps 2437.5 ns
tTWIM,SU_STO,100kbps TWIM master setup time from SCL high to STOP condition, 100 kbps 5000 ns
tTWIM,SU_STO,250kbps TWIM master setup time from SCL high to STOP condition, 250 kbps 2000 ns
tTWIM,SU_STO,400kbps TWIM master setup time from SCL high to STOP condition, 400 kbps 1250 ns
tTWIM,BUF,100kbps TWIM master bus free time between STOP and START conditions, 100 kbps 5800 ns
tTWIM,BUF,250kbps TWIM master bus free time between STOP and START conditions, 250 kbps 2700 ns
tTWIM,BUF,400kbps TWIM master bus free time between STOP and START conditions, 400 kbps 2100 ns

Figure 180: TWIM timing diagram, 1 byte transaction

40
High bit rates or stronger pull-ups may require GPIOs to be set as High Drive, see GPIO — General
purpose input/output on page 240 for more details.

4413_417 v1.9 720

 Peripherals

6.31.9 Pullup resistor

R [kΩ]
30

25 100 kbps
400 kbps
20

15

10

0
0 100 200 300 400 500
cap [pF]

Figure 181: Recommended TWIM pullup value vs. line capacitance

• The I2C specification allows a line capacitance of 400 pF at most.

• The value of internal pullup resistor (RPU) for nRF52840 can be found in GPIO — General purpose
input/output on page 240.

6.32 TWIS — I2C compatible two-wire interface slave

with EasyDMA
TWI slave with EasyDMA (TWIS) is compatible with I2C operating at 100 kHz and 400 kHz. The TWI
transmitter and receiver implement EasyDMA.
PSEL.SDA PSEL.SCK PSEL.SDA

PREPARETX
PREPARERX RXD TXD STOPPED
(signal) (signal)
SUSPEND WRITE
RESUME RXD.PTR EasyDMA EasyDMA TXD.PTR READ

RAM
RXD TXD
RXD+1 TXD+1
RXD+2 TXD+2
RXD+n TXD+n

Figure 182: TWI slave with EasyDMA

A typical TWI setup consists of one master and one or more slaves. For an example, see the following
figure. TWIS is only able to operate with a single master on the TWI bus.

4413_417 v1.9 721

 Peripherals

VDD VDD
TWI slave
TWI slave TWI slave
(TWIS)
(EEPROM) (Sensor)
TWI master
Address = b1011001 Address = b1011000
Address = b1011011
R R
SDA SCL SCL SDA SCL SDA SCL SDA

Figure 183: A typical TWI setup comprising one master and three slaves

The following figure shows the TWI slave state machine.

PREPARETX ENABLE PREPARERX

/ STOPPED
Unprepare TX,
Unprepare RX

IDLE

STOP
[ READ && (TX prepared) ] [ WRITE && (RX prepared) ]

Restart sequence

TX RX

entry / Unprepare TX entry / Unprepare RX

Stop sequence entry / RXSTARTED
entry / TXSTARTED

Figure 184: TWI slave state machine

The following table contains descriptions of the symbols used in the state machine.

4413_417 v1.9 722

 Peripherals

Symbol Type Description

ENABLE Register The TWI slave has been enabled via the ENABLE register.
PREPARETX Task The TASKS_PREPARETX task has been triggered.
STOP Task The TASKS_STOP task has been triggered.
PREPARERX Task The TASKS_PREPARERX task has been triggered.
STOPPED Event The EVENTS_STOPPED event was generated.
RXSTARTED Event The EVENTS_RXSTARTED event was generated.
TXSTARTED Event The EVENTS_TXSTARTED event was generated.
TX prepared Internal Internal flag indicating that a TASKS_PREPARETX task has been triggered. This flag is not visible to the
user.
RX prepared Internal Internal flag indicating that a TASKS_PREPARERX task has been triggered. This flag is not visible to the
user.
Unprepare TX Internal Clears the internal 'TX prepared' flag until next TASKS_PREPARETX task.
Unprepare RX Internal Clears the internal 'RX prepared' flag until next TASKS_PREPARERX task.
Stop condition TWI protocol A TWI stop condition was detected.
Restart condition TWI protocol A TWI restart condition was detected.

Table 53: TWI slave state machine symbols

The TWI slave can perform clock stretching, with the premise that the master is able to support it.
The TWI slave operates in a low power mode while waiting for a TWI master to initiate a transfer. As long
as the TWI slave is not addressed, it will remain in this low power mode.
To secure correct behavior of the TWI slave, PSEL.SCL, PSEL.SDA, CONFIG, and the ADDRESS[n] registers
must be configured prior to enabling the TWI slave through the ENABLE register. Similarly, changing these
settings must be performed while the TWI slave is disabled. Failing to do so may result in unpredictable
behavior.

6.32.1 EasyDMA
The TWIS implements EasyDMA for accessing RAM without CPU involvement.
The following table shows the Easy DMA channels that the TWIS peripheral implements.

Channel Type Register Cluster

TXD READER TXD
RXD WRITER RXD

Table 54: TWIS EasyDMA Channels

For detailed information regarding the use of EasyDMA, see EasyDMA on page 62.
The STOPPED event indicates that EasyDMA has finished accessing the buffer in RAM.

6.32.2 TWI slave responding to a read command

Before the TWI slave can respond to a read command, the TWI slave must be configured correctly and
enabled via the ENABLE register. When enabled, the TWI slave will be in its IDLE state. .
A read command is started when the TWI master generates a start condition on the TWI bus, followed
by clocking out the address and the READ/WRITE bit set to 1 (WRITE=0, READ=1). The READ/WRITE bit is
followed by an ACK/NACK bit (ACK=0 or NACK=1) response from the TWI slave.
The TWI slave is able to listen for up to two addresses at the same time. This is configured in the ADDRESS
registers and the CONFIG register.

4413_417 v1.9 723

 Peripherals

The TWI slave will only acknowledge (ACK) the read command if the address presented by the master
matches one of the addresses the slave is configured to listen for. The TWI slave will generate a READ
event when it acknowledges the read command.
The TWI slave is only able to detect a read command from the IDLE state.
The TWI slave will set an internal 'TX prepared' flag when the PREPARETX task is triggered.
When the read command is received, the TWI slave will enter the TX state if the internal 'TX prepared' flag
is set.
If the internal 'TX prepared' flag is not set when the read command is received, the TWI slave will stretch
the master's clock until the PREPARETX task is triggered and the internal 'TX prepared' flag is set.
The TWI slave will generate the TXSTARTED event and clear the 'TX prepared' flag ('unprepare TX') when it
enters the TX state. In this state the TWI slave will send the data bytes found in the transmit buffer to the
master using the master's clock.
The TWI slave will go back to the IDLE state if the TWI slave receives a restart command when it is in the
TX state.
The TWI slave is stopped when it receives the stop condition from the TWI master. A STOPPED event
will be generated when the transaction has stopped. The TWI slave will clear the 'TX prepared' flag
('unprepare TX') and go back to the IDLE state when it has stopped.
The transmit buffer is located in RAM at the address specified in the TXD.PTR register. The TWI slave will
only be able to send TXD.MAXCNT bytes from the transmit buffer for each transaction. If the TWI master
forces the slave to send more than TXD.MAXCNT bytes, the slave will send the byte specified in the ORC
register to the master instead. If this happens, an ERROR event will be generated.
The EasyDMA configuration registers, see TXD.PTR etc., are latched when the TXSTARTED event is
generated.
The TWI slave can be forced to stop by triggering the STOP task. A STOPPED event will be generated when
the TWI slave has stopped. The TWI slave will clear the 'TX prepared' flag and go back to the IDLE state
when it has stopped, see also Terminating an ongoing TWI transaction on page 726.
Each byte sent from the slave will be followed by an ACK/NACK bit sent from the master. The TWI master
will generate a NACK following the last byte that it wants to receive to tell the slave to release the bus so
that the TWI master can generate the stop condition. The TXD.AMOUNT register can be queried after a
transaction to see how many bytes were sent.
A typical TWI slave read command response is shown in the following figure. Occurrence 2 in the figure
illustrates clock stretching performed by the TWI slave following a SUSPEND task.

Stretch
START

READ

NACK
STOP
ACK

ACK

ACK

ACK

ACK
TWI

ADDR 0 1 2 N-1 N
STOPPED
TXSTARTED
READ
CPU Lifeline

1 2 3 4
TXD.PTR = 0x20000000
TXD.MAXCNT >= N+1

PREPARETX

RESUME
SUSPEND

Figure 185: The TWI slave responding to a read command

4413_417 v1.9 724

 Peripherals

6.32.3 TWI slave responding to a write command

Before the TWI slave can respond to a write command, the TWI slave must be configured correctly and
enabled via the ENABLE register. When enabled, the TWI slave will be in its IDLE state.
A write command is started when the TWI master generates a start condition on the TWI bus, followed
by clocking out the address and the READ/WRITE bit set to 0 (WRITE=0, READ=1). The READ/WRITE bit is
followed by an ACK/NACK bit (ACK=0 or NACK=1) response from the slave.
The TWI slave is able to listen for up to two addresses at the same time. This is configured in the ADDRESS
registers and the CONFIG register.
The TWI slave will only acknowledge (ACK) the write command if the address presented by the master
matches one of the addresses the slave is configured to listen for. The TWI slave will generate a WRITE
event if it acknowledges the write command.
The TWI slave is only able to detect a write command from the IDLE state.
The TWI slave will set an internal 'RX prepared' flag when the PREPARERX task is triggered.
When the write command is received, the TWI slave will enter the RX state if the internal 'RX prepared'
flag is set.
If the internal 'RX prepared' flag is not set when the write command is received, the TWI slave will stretch
the master's clock until the PREPARERX task is triggered and the internal 'RX prepared' flag is set.
The TWI slave will generate the RXSTARTED event and clear the internal 'RX prepared' flag ('unprepare RX')
when it enters the RX state. In this state, the TWI slave will be able to receive the bytes sent by the TWI
master.
The TWI slave will go back to the IDLE state if the TWI slave receives a restart command when it is in the
RX state.
The TWI slave is stopped when it receives the stop condition from the TWI master. A STOPPED event will
be generated when the transaction has stopped. The TWI slave will clear the internal 'RX prepared' flag
('unprepare RX') and go back to the IDLE state when it has stopped.
The receive buffer is located in RAM at the address specified in the RXD.PTR register. The TWI slave will
only be able to receive as many bytes as specified in the RXD.MAXCNT register. If the TWI master tries to
send more bytes to the slave than it can receive, the extra bytes are discarded and NACKed by the slave. If
this happens, an ERROR event will be generated.
The EasyDMA configuration registers, see RXD.PTR etc., are latched when the RXSTARTED event is
generated.
The TWI slave can be forced to stop by triggering the STOP task. A STOPPED event will be generated when
the TWI slave has stopped. The TWI slave will clear the internal 'RX prepared' flag and go back to the IDLE
state when it has stopped, see also Terminating an ongoing TWI transaction on page 726.
The TWI slave will generate an ACK after every byte received from the master. The RXD.AMOUNT register
can be queried after a transaction to see how many bytes were received.
A typical TWI slave write command response is show in the following figure. Occurrence 2 in the figure
illustrates clock stretching performed by the TWI slave following a SUSPEND task.

4413_417 v1.9 725

 Peripherals

START

WRITE
Stretch

STOP
ACK

ACK

ACK

ACK

ACK

ACK
TWI
ADDR 0 1 2 M-1 M

STOPPED
RXSTARTED
WRITE
CPU Lifeline

1 2 3 4
RXD.MAXCNT >= M+1

RXD.PTR = 0x20000000
PREPARERX

RESUME
SUSPEND
Figure 186: The TWI slave responding to a write command

6.32.4 Master repeated start sequence

An example of a repeated start sequence is one in which the TWI master writes two bytes to the slave
followed by reading four bytes from the slave.
This is illustrated in the following figure.
In this example, the receiver does not know what the master wants to read in advance. This information
is in the first two received bytes of the write in the repeated start sequence. To guarantee that the CPU is
able to process the received data before the TWI slave starts to reply to the read command, the SUSPEND
task is triggered via a shortcut from the READ event generated when the read command is received. When
the CPU has processed the incoming data and prepared the correct data response, the CPU will resume
the transaction by triggering the RESUME task.
RESTART
START

WRITE

READ

NACK
STOP
TWI

ACK

ACK

ACK
ACK

ACK

ACK

ACK

ADDR 0 1 ADDR 0 1 2 3
TXSTARTED

STOPPED
RXSTARTED

READ
WRITE
CPU Lifeline

1 2 3
RXD.PTR = 0x20000000

TXD.PTR = 0x20000010
RXD.MAXCNT = 2

PREPARERX

TXD.MAXCNT = 4
PREPARETX
SUSPEND

RESUME

Figure 187: Repeated start sequence

6.32.5 Terminating an ongoing TWI transaction

In some situations, e.g. if the external TWI master is not responding correctly, it may be required to
terminate an ongoing transaction.
This can be achieved by triggering the STOP task. In this situation, a STOPPED event will be generated
when the TWI has stopped independent of whether or not a STOP condition has been generated on the
TWI bus. The TWI slave will release the bus when it has stopped and go back to its IDLE state.

4413_417 v1.9 726

 Peripherals

6.32.6 Low power

When putting the system in low power and the peripheral is not needed, lowest possible power
consumption is achieved by stopping, and then disabling the peripheral.
The STOP task may not be always needed (the peripheral might already be stopped), but if it is sent,
software shall wait until the STOPPED event was received as a response before disabling the peripheral
through the ENABLE register.

6.32.7 Slave mode pin configuration

The SCL and SDA signals associated with the TWI slave are mapped to physical pins according to the
configuration specified in the PSEL.SCL and PSEL.SDA registers respectively.
The PSEL.SCL and PSEL.SDA registers and their configurations are only used as long as the TWI slave is
enabled, and retained only as long as the device is in ON mode. When the peripheral is disabled, the pins
will behave as regular GPIOs, and use the configuration in their respective OUT bit field and PIN_CNF[n]
register. PSEL.SCL and PSEL.SDA must only be configured when the TWI slave is disabled.
To secure correct signal levels on the pins used by the TWI slave when the system is in OFF mode, and
when the TWI slave is disabled, these pins must be configured in the GPIO peripheral as described in the
following table.
Only one peripheral can be assigned to drive a particular GPIO pin at a time. Failing to do so may result in
unpredictable behavior.

TWI slave signal TWI slave pin Direction Output value Drive strength

SCL As specified in PSEL.SCL Input Not applicable S0D1

SDA As specified in PSEL.SDA Input Not applicable S0D1

Table 55: GPIO configuration before enabling peripheral

6.32.8 Registers
Instances

Instance Base address Description

TWIS0 0x40003000 Two-wire interface slave 0
TWIS1 0x40004000 Two-wire interface slave 1

Register overview

Register Offset Description

TASKS_STOP 0x014 Stop TWI transaction
TASKS_SUSPEND 0x01C Suspend TWI transaction
TASKS_RESUME 0x020 Resume TWI transaction
TASKS_PREPARERX 0x030 Prepare the TWI slave to respond to a write command
TASKS_PREPARETX 0x034 Prepare the TWI slave to respond to a read command
EVENTS_STOPPED 0x104 TWI stopped
EVENTS_ERROR 0x124 TWI error
EVENTS_RXSTARTED 0x14C Receive sequence started
EVENTS_TXSTARTED 0x150 Transmit sequence started
EVENTS_WRITE 0x164 Write command received
EVENTS_READ 0x168 Read command received
SHORTS 0x200 Shortcuts between local events and tasks

4413_417 v1.9 727

 Peripherals

Register Offset Description

INTEN 0x300 Enable or disable interrupt
INTENSET 0x304 Enable interrupt
INTENCLR 0x308 Disable interrupt
ERRORSRC 0x4D0 Error source
MATCH 0x4D4 Status register indicating which address had a match
ENABLE 0x500 Enable TWIS
PSEL.SCL 0x508 Pin select for SCL signal
PSEL.SDA 0x50C Pin select for SDA signal
RXD.PTR 0x534 RXD Data pointer
RXD.MAXCNT 0x538 Maximum number of bytes in RXD buffer
RXD.AMOUNT 0x53C Number of bytes transferred in the last RXD transaction
RXD.LIST 0x540 EasyDMA list type
TXD.PTR 0x544 TXD Data pointer
TXD.MAXCNT 0x548 Maximum number of bytes in TXD buffer
TXD.AMOUNT 0x54C Number of bytes transferred in the last TXD transaction
TXD.LIST 0x550 EasyDMA list type
ADDRESS[0] 0x588 TWI slave address 0
ADDRESS[1] 0x58C TWI slave address 1
CONFIG 0x594 Configuration register for the address match mechanism
ORC 0x5C0 Over-read character. Character sent out in case of an over-read of the transmit buffer.

6.32.8.1 TASKS_STOP
Address offset: 0x014
Stop TWI transaction

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STOP Stop TWI transaction
Trigger 1 Trigger task

6.32.8.2 TASKS_SUSPEND
Address offset: 0x01C
Suspend TWI transaction

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_SUSPEND Suspend TWI transaction
Trigger 1 Trigger task

6.32.8.3 TASKS_RESUME
Address offset: 0x020
Resume TWI transaction

4413_417 v1.9 728

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_RESUME Resume TWI transaction
Trigger 1 Trigger task

6.32.8.4 TASKS_PREPARERX
Address offset: 0x030
Prepare the TWI slave to respond to a write command

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_PREPARERX Prepare the TWI slave to respond to a write command
Trigger 1 Trigger task

6.32.8.5 TASKS_PREPARETX
Address offset: 0x034
Prepare the TWI slave to respond to a read command

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_PREPARETX Prepare the TWI slave to respond to a read command
Trigger 1 Trigger task

6.32.8.6 EVENTS_STOPPED
Address offset: 0x104
TWI stopped

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_STOPPED TWI stopped
NotGenerated 0 Event not generated
Generated 1 Event generated

6.32.8.7 EVENTS_ERROR
Address offset: 0x124
TWI error

4413_417 v1.9 729

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_ERROR TWI error
NotGenerated 0 Event not generated
Generated 1 Event generated

6.32.8.8 EVENTS_RXSTARTED
Address offset: 0x14C
Receive sequence started

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_RXSTARTED Receive sequence started
NotGenerated 0 Event not generated
Generated 1 Event generated

6.32.8.9 EVENTS_TXSTARTED
Address offset: 0x150
Transmit sequence started

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_TXSTARTED Transmit sequence started
NotGenerated 0 Event not generated
Generated 1 Event generated

6.32.8.10 EVENTS_WRITE
Address offset: 0x164
Write command received

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_WRITE Write command received
NotGenerated 0 Event not generated
Generated 1 Event generated

6.32.8.11 EVENTS_READ
Address offset: 0x168
Read command received

4413_417 v1.9 730

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_READ Read command received
NotGenerated 0 Event not generated
Generated 1 Event generated

6.32.8.12 SHORTS
Address offset: 0x200
Shortcuts between local events and tasks

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW WRITE_SUSPEND Shortcut between event WRITE and task SUSPEND
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
B RW READ_SUSPEND Shortcut between event READ and task SUSPEND
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut

6.32.8.13 INTEN
Address offset: 0x300
Enable or disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID H G F E B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW STOPPED Enable or disable interrupt for event STOPPED
Disabled 0 Disable
Enabled 1 Enable
B RW ERROR Enable or disable interrupt for event ERROR
Disabled 0 Disable
Enabled 1 Enable
E RW RXSTARTED Enable or disable interrupt for event RXSTARTED
Disabled 0 Disable
Enabled 1 Enable
F RW TXSTARTED Enable or disable interrupt for event TXSTARTED
Disabled 0 Disable
Enabled 1 Enable
G RW WRITE Enable or disable interrupt for event WRITE
Disabled 0 Disable
Enabled 1 Enable
H RW READ Enable or disable interrupt for event READ
Disabled 0 Disable
Enabled 1 Enable

4413_417 v1.9 731

 Peripherals

6.32.8.14 INTENSET
Address offset: 0x304
Enable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID H G F E B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW STOPPED Write '1' to enable interrupt for event STOPPED
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW ERROR Write '1' to enable interrupt for event ERROR
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
E RW RXSTARTED Write '1' to enable interrupt for event RXSTARTED
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
F RW TXSTARTED Write '1' to enable interrupt for event TXSTARTED
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
G RW WRITE Write '1' to enable interrupt for event WRITE
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
H RW READ Write '1' to enable interrupt for event READ
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.32.8.15 INTENCLR
Address offset: 0x308
Disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID H G F E B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW STOPPED Write '1' to disable interrupt for event STOPPED
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW ERROR Write '1' to disable interrupt for event ERROR
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
E RW RXSTARTED Write '1' to disable interrupt for event RXSTARTED
Clear 1 Disable

4413_417 v1.9 732

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID H G F E B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
F RW TXSTARTED Write '1' to disable interrupt for event TXSTARTED
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
G RW WRITE Write '1' to disable interrupt for event WRITE
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
H RW READ Write '1' to disable interrupt for event READ
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.32.8.16 ERRORSRC
Address offset: 0x4D0
Error source

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW OVERFLOW RX buffer overflow detected, and prevented
W1C
NotDetected 0 Error did not occur
Detected 1 Error occurred
B RW DNACK NACK sent after receiving a data byte
W1C
NotReceived 0 Error did not occur
Received 1 Error occurred
C RW OVERREAD TX buffer over-read detected, and prevented
W1C
NotDetected 0 Error did not occur
Detected 1 Error occurred

6.32.8.17 MATCH
Address offset: 0x4D4
Status register indicating which address had a match

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R MATCH [0..1] Indication of which address in ADDRESS that matched the incoming address

4413_417 v1.9 733

 Peripherals

6.32.8.18 ENABLE
Address offset: 0x500
Enable TWIS

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW ENABLE Enable or disable TWIS
Disabled 0 Disable TWIS
Enabled 9 Enable TWIS

6.32.8.19 PSEL.SCL
Address offset: 0x508
Pin select for SCL signal

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.32.8.20 PSEL.SDA
Address offset: 0x50C
Pin select for SDA signal

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.32.8.21 RXD
RXD EasyDMA channel

6.32.8.21.1 RXD.PTR
Address offset: 0x534
RXD Data pointer

4413_417 v1.9 734

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PTR RXD Data pointer

See the memory chapter for details about which memories are available for
EasyDMA.

6.32.8.21.2 RXD.MAXCNT
Address offset: 0x538
Maximum number of bytes in RXD buffer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW MAXCNT [0..0xFFFF] Maximum number of bytes in RXD buffer

6.32.8.21.3 RXD.AMOUNT
Address offset: 0x53C
Number of bytes transferred in the last RXD transaction

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R AMOUNT [0..0xFFFF] Number of bytes transferred in the last RXD transaction

6.32.8.21.4 RXD.LIST
Address offset: 0x540
EasyDMA list type

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW LIST List type
Disabled 0 Disable EasyDMA list
ArrayList 1 Use array list

6.32.8.22 TXD
TXD EasyDMA channel

6.32.8.22.1 TXD.PTR
Address offset: 0x544
TXD Data pointer

4413_417 v1.9 735

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PTR TXD Data pointer

See the memory chapter for details about which memories are available for
EasyDMA.

6.32.8.22.2 TXD.MAXCNT
Address offset: 0x548
Maximum number of bytes in TXD buffer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW MAXCNT [0..0xFFFF] Maximum number of bytes in TXD buffer

6.32.8.22.3 TXD.AMOUNT
Address offset: 0x54C
Number of bytes transferred in the last TXD transaction

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R AMOUNT [0..0xFFFF] Number of bytes transferred in the last TXD transaction

6.32.8.22.4 TXD.LIST
Address offset: 0x550
EasyDMA list type

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW LIST List type
Disabled 0 Disable EasyDMA list
ArrayList 1 Use array list

6.32.8.23 ADDRESS[0]
Address offset: 0x588
TWI slave address 0

4413_417 v1.9 736

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW ADDRESS TWI slave address

6.32.8.24 ADDRESS[1]
Address offset: 0x58C
TWI slave address 1

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW ADDRESS TWI slave address

6.32.8.25 CONFIG
Address offset: 0x594
Configuration register for the address match mechanism

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B A

Reset 0x00000001 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
ID R/W Field Value ID Value Description
A RW ADDRESS0 Enable or disable address matching on ADDRESS[0]
Disabled 0 Disabled
Enabled 1 Enabled
B RW ADDRESS1 Enable or disable address matching on ADDRESS[1]
Disabled 0 Disabled
Enabled 1 Enabled

6.32.8.26 ORC
Address offset: 0x5C0
Over-read character. Character sent out in case of an over-read of the transmit buffer.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW ORC Over-read character. Character sent out in case of an over-read of the
transmit buffer.

4413_417 v1.9 737

 Peripherals

6.32.9 Electrical specification

6.32.9.1 TWIS slave timing specifications

Symbol Description Min. Typ. Max. Units

fTWIS,SCL 41
Bit rates for TWIS 100 400 kbps

tTWIS,START Time from PREPARERX/PREPARETX task to ready to receive/transmit 1.5 µs

tTWIS,SU_DAT Data setup time before positive edge on SCL – all modes 300 ns
tTWIS,HD_DAT Data hold time after negative edge on SCL – all modes 500 ns
tTWIS,HD_STA,100kbps TWI slave hold time from for START condition (SDA low to SCL low), 100 kbps 5200 ns
tTWIS,HD_STA,400kbps TWI slave hold time from for START condition (SDA low to SCL low), 400 kbps 1300 ns
tTWIS,SU_STO,100kbps TWI slave setup time from SCL high to STOP condition, 100 kbps 5200 ns
tTWIS,SU_STO,400kbps TWI slave setup time from SCL high to STOP condition, 400 kbps 1300 ns
tTWIS,BUF,100kbps TWI slave bus free time between STOP and START conditions, 100 kbps 4700 ns
tTWIS,BUF,400kbps TWI slave bus free time between STOP and START conditions, 400 kbps 1300 ns

Figure 188: TWIS timing diagram, 1 byte transaction

6.33 UART — Universal asynchronous receiver/

transmitter
PSEL.RXD PSEL.CTS PSEL.RTS PSEL.TXD

STARTTX
STARTRX
RXD-5
RXD TXD STOPTX
STOPRX RXD-4 TXD
(signal)
RXD-3 (signal)
RXD-2
RXD-1
RXTO
RXD

RXDRDY TXDRDY

Figure 189: UART configuration

6.33.1 Functional description

Listed here are the main features of UART.
The UART implements support for the following features:
• Full-duplex operation

41
High bit rates or stronger pull-ups may require GPIOs to be set as High Drive, see GPIO chapter for
more details.

4413_417 v1.9 738

 Peripherals

• Automatic flow control

• Parity checking and generation for the 9th data bit
As illustrated in UART configuration on page 738, the UART uses the TXD and RXD registers directly to
transmit and receive data. The UART uses one stop bit.

Note: The external crystal oscillator must be enabled to obtain sufficient clock accuracy for stable
communication. See CLOCK — Clock control on page 156 for more information.

6.33.2 Pin configuration

The different signals RXD, CTS (Clear To Send, active low), RTS (Request To Send, active low), and TXD
associated with the UART are mapped to physical pins according to the configuration specified in the
PSEL.RXD, PSEL.CTS, PSEL.RTS, and PSEL.TXD registers respectively.
If the CONNECT field of a PSEL.xxx register is set to Disconnected, the associated UART signal will not
be connected to any physical pin. The PSEL.RXD, PSEL.CTS, PSEL.RTS, and PSEL.TXD registers and their
configurations are only used as long as the UART is enabled, and retained only for the duration the device
is in ON mode. PSEL.RXD, PSEL.CTS, PSEL.RTS, and PSEL.TXD must only be configured when the UART is
disabled.
To secure correct signal levels on the pins by the UART when the system is in OFF mode, the pins must be
configured in the GPIO peripheral as described in Pin configuration on page 739.
Only one peripheral can be assigned to drive a particular GPIO pin at a time. Failing to do so may result in
unpredictable behavior.

UART pin Direction Output value

RXD Input Not applicable
CTS Input Not applicable
RTS Output 1
TXD Output 1

Table 56: GPIO configuration

6.33.3 Shared resources

The UART shares registers and resources with other peripherals that have the same ID as the UART.
All peripherals with the same ID as the UART must be disabled before configuring and using the UART.
Disabling a peripheral that has the same ID as the UART will not reset any of the registers that are shared
with the UART. It is therefore important to configure all relevant UART registers explicitly to ensure that it
operates correctly.
See Instantiation on page 24 for details on peripherals and their IDs.

6.33.4 Transmission
A UART transmission sequence is started by triggering the STARTTX task.
Bytes are transmitted by writing to the TXD register. When a byte has been successfully transmitted, the
UART will generate a TXDRDY event after which a new byte can be written to the TXD register. A UART
transmission sequence is stopped immediately by triggering the STOPTX task.
If flow control is enabled, a transmission will be automatically suspended when CTS is deactivated, and
resumed when CTS is activated again, as shown in the following figure. A byte that is in transmission when
CTS is deactivated will be fully transmitted before the transmission is suspended. For more information,
see Suspending the UART on page 741.

4413_417 v1.9 739

 Peripherals

CTS
TXD

0 1 2 N-2 N-1 N

TXDRDY

TXDRDY
TXDRDY

TXDRDY

TXDRDY
Lifeline

1 2 3 5 5 6

TXD = N-1
STARTTX

STOPTX
TXD = N
TXD = 0

TXD = 1

TXD = 2

Figure 190: UART transmission

6.33.5 Reception
A UART reception sequence is started by triggering the STARTRX task.
The UART receiver chain implements a FIFO capable of storing six incoming RXD bytes before data is
overwritten. Bytes are extracted from this FIFO by reading the RXD register. When a byte is extracted from
the FIFO, a new byte pending in the FIFO will be moved to the RXD register. The UART will generate an
RXDRDY event every time a new byte is moved to the RXD register.
When flow control is enabled, the UART will deactivate the RTS signal when there is only space for four
more bytes in the receiver FIFO. The counterpart transmitter is therefore able to send up to four bytes
after the RTS signal is deactivated before data is being overwritten. To prevent overwriting data in the
FIFO, the counterpart UART transmitter must therefore make sure to stop transmitting data within four
bytes after the RTS line is deactivated.
The RTS signal will first be activated again when the FIFO has been emptied, that is, when all bytes in the
FIFO have been read by the CPU, see UART reception on page 741.
The RTS signal will also be deactivated when the receiver is stopped through the STOPRX task as illustrated
in UART reception on page 741. The UART is able to receive four to five additional bytes if they are sent
in succession immediately after the RTS signal has been deactivated. This is possible because the UART is,
even after the STOPRX task is triggered, able to receive bytes for an extended period of time dependent
on the configured baud rate. The UART will generate a receiver timeout event (RXTO) when this period has
elapsed.
To prevent loss of incoming data, the RXD register must only be read one time following every RXDRDY
event.
To secure that the CPU can detect all incoming RXDRDY events through the RXDRDY event register, the
RXDRDY event register must be cleared before the RXD register is read. The reason for this is that the
UART is allowed to write a new byte to the RXD register, and can generate a new event immediately after
the RXD register is read (emptied) by the CPU.

4413_417 v1.9 740

 Peripherals

RTS
RXD

A B C F M-2 M-1 M

RXDRDY

RXDRDY
RXDRDY
RXDRDY
RXDRDY
RXDRDY

RXDRDY

RXDRDY

RXDRDY

RXTO
Lifeline

1 2 3 4 5 6 7 5 6 7

M-2 = RXD

M-1 = RXD
STARTRX

M = RXD
STOPRX
C = RXD
D = RXD
A = RXD
B = RXD

E = RXD
F = RXD
Figure 191: UART reception

As indicated in occurrence 2 in the figure, the RXDRDY event associated with byte B is generated first after
byte A has been extracted from RXD.

6.33.6 Suspending the UART

The UART can be suspended by triggering the SUSPEND task.
SUSPEND will affect both the UART receiver and the UART transmitter, i.e. the transmitter will stop
transmitting and the receiver will stop receiving. UART transmission and reception can be resumed, after
being suspended, by triggering STARTTX and STARTRX respectively.
Following a SUSPEND task, an ongoing TXD byte transmission will be completed before the UART is
suspended.
When the SUSPEND task is triggered, the UART receiver will behave in the same way as it does when the
STOPRX task is triggered.

6.33.7 Error conditions

An ERROR event, in the form of a framing error, will be generated if a valid stop bit is not detected in a
frame. Another ERROR event, in the form of a break condition, will be generated if the RXD line is held
active low for longer than the length of a data frame. Effectively, a framing error is always generated
before a break condition occurs.

6.33.8 Using the UART without flow control

If flow control is not enabled, the interface will behave as if the CTS and RTS lines are kept active all the
time.

6.33.9 Parity and stop bit configuration

Automatic even parity generation for both transmission and reception can be configured using the register
CONFIG on page 749. See the register description for details.
The amount of stop bits can also be configured through the register CONFIG on page 749.

6.33.10 Registers
Instances

Instance Base address Description

UART0 0x40002000 Universal asynchronous receiver/transmitter

This instance is deprecated.

4413_417 v1.9 741

 Peripherals

Register overview

Register Offset Description

TASKS_STARTRX 0x000 Start UART receiver
TASKS_STOPRX 0x004 Stop UART receiver
TASKS_STARTTX 0x008 Start UART transmitter
TASKS_STOPTX 0x00C Stop UART transmitter
TASKS_SUSPEND 0x01C Suspend UART
EVENTS_CTS 0x100 CTS is activated (set low). Clear To Send.
EVENTS_NCTS 0x104 CTS is deactivated (set high). Not Clear To Send.
EVENTS_RXDRDY 0x108 Data received in RXD
EVENTS_TXDRDY 0x11C Data sent from TXD
EVENTS_ERROR 0x124 Error detected
EVENTS_RXTO 0x144 Receiver timeout
SHORTS 0x200 Shortcuts between local events and tasks
INTENSET 0x304 Enable interrupt
INTENCLR 0x308 Disable interrupt
ERRORSRC 0x480 Error source
ENABLE 0x500 Enable UART
PSEL.RTS 0x508 Pin select for RTS
PSEL.TXD 0x50C Pin select for TXD
PSEL.CTS 0x510 Pin select for CTS
PSEL.RXD 0x514 Pin select for RXD
RXD 0x518 RXD register. Register is cleared on read and the double buffered byte will be moved to RXD if it
exists.
TXD 0x51C TXD register
BAUDRATE 0x524 Baud rate. Accuracy depends on the HFCLK source selected.
CONFIG 0x56C Configuration of parity and hardware flow control

6.33.10.1 TASKS_STARTRX
Address offset: 0x000
Start UART receiver

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STARTRX Start UART receiver
Trigger 1 Trigger task

6.33.10.2 TASKS_STOPRX
Address offset: 0x004
Stop UART receiver

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STOPRX Stop UART receiver
Trigger 1 Trigger task

4413_417 v1.9 742

 Peripherals

6.33.10.3 TASKS_STARTTX
Address offset: 0x008
Start UART transmitter

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STARTTX Start UART transmitter
Trigger 1 Trigger task

6.33.10.4 TASKS_STOPTX
Address offset: 0x00C
Stop UART transmitter

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STOPTX Stop UART transmitter
Trigger 1 Trigger task

6.33.10.5 TASKS_SUSPEND
Address offset: 0x01C
Suspend UART

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_SUSPEND Suspend UART
Trigger 1 Trigger task

6.33.10.6 EVENTS_CTS
Address offset: 0x100
CTS is activated (set low). Clear To Send.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_CTS CTS is activated (set low). Clear To Send.
NotGenerated 0 Event not generated
Generated 1 Event generated

4413_417 v1.9 743

 Peripherals

6.33.10.7 EVENTS_NCTS
Address offset: 0x104
CTS is deactivated (set high). Not Clear To Send.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_NCTS CTS is deactivated (set high). Not Clear To Send.
NotGenerated 0 Event not generated
Generated 1 Event generated

6.33.10.8 EVENTS_RXDRDY
Address offset: 0x108
Data received in RXD

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_RXDRDY Data received in RXD
NotGenerated 0 Event not generated
Generated 1 Event generated

6.33.10.9 EVENTS_TXDRDY
Address offset: 0x11C
Data sent from TXD

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_TXDRDY Data sent from TXD
NotGenerated 0 Event not generated
Generated 1 Event generated

6.33.10.10 EVENTS_ERROR
Address offset: 0x124
Error detected

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_ERROR Error detected
NotGenerated 0 Event not generated
Generated 1 Event generated

4413_417 v1.9 744

 Peripherals

6.33.10.11 EVENTS_RXTO
Address offset: 0x144
Receiver timeout

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_RXTO Receiver timeout
NotGenerated 0 Event not generated
Generated 1 Event generated

6.33.10.12 SHORTS
Address offset: 0x200
Shortcuts between local events and tasks

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW CTS_STARTRX Shortcut between event CTS and task STARTRX
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
B RW NCTS_STOPRX Shortcut between event NCTS and task STOPRX
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut

6.33.10.13 INTENSET
Address offset: 0x304
Enable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW CTS Write '1' to enable interrupt for event CTS
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW NCTS Write '1' to enable interrupt for event NCTS
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW RXDRDY Write '1' to enable interrupt for event RXDRDY
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
D RW TXDRDY Write '1' to enable interrupt for event TXDRDY
Set 1 Enable

4413_417 v1.9 745

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
E RW ERROR Write '1' to enable interrupt for event ERROR
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
F RW RXTO Write '1' to enable interrupt for event RXTO
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.33.10.14 INTENCLR
Address offset: 0x308
Disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW CTS Write '1' to disable interrupt for event CTS
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW NCTS Write '1' to disable interrupt for event NCTS
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW RXDRDY Write '1' to disable interrupt for event RXDRDY
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
D RW TXDRDY Write '1' to disable interrupt for event TXDRDY
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
E RW ERROR Write '1' to disable interrupt for event ERROR
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
F RW RXTO Write '1' to disable interrupt for event RXTO
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.33.10.15 ERRORSRC
Address offset: 0x480
Error source

4413_417 v1.9 746

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW OVERRUN Overrun error
W1C
A start bit is received while the previous data still lies in RXD. (Previous data
is lost.)
NotPresent 0 Read: error not present
Present 1 Read: error present
B RW PARITY Parity error
W1C
A character with bad parity is received, if HW parity check is enabled.
NotPresent 0 Read: error not present
Present 1 Read: error present
C RW FRAMING Framing error occurred
W1C
A valid stop bit is not detected on the serial data input after all bits in a
character have been received.
NotPresent 0 Read: error not present
Present 1 Read: error present
D RW BREAK Break condition
W1C
The serial data input is '0' for longer than the length of a data frame. (The
data frame length is 10 bits without parity bit, and 11 bits with parity bit.).
NotPresent 0 Read: error not present
Present 1 Read: error present

6.33.10.16 ENABLE
Address offset: 0x500
Enable UART

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW ENABLE Enable or disable UART
Disabled 0 Disable UART
Enabled 4 Enable UART

6.33.10.17 PSEL.RTS
Address offset: 0x508
Pin select for RTS

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

4413_417 v1.9 747

 Peripherals

6.33.10.18 PSEL.TXD
Address offset: 0x50C
Pin select for TXD

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.33.10.19 PSEL.CTS
Address offset: 0x510
Pin select for CTS

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.33.10.20 PSEL.RXD
Address offset: 0x514
Pin select for RXD

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.33.10.21 RXD
Address offset: 0x518
RXD register. Register is cleared on read and the double buffered byte will be moved to RXD if it exists.

4413_417 v1.9 748

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R RXD RX data received in previous transfers, double buffered
RME

6.33.10.22 TXD
Address offset: 0x51C
TXD register

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TXD TX data to be transferred

6.33.10.23 BAUDRATE
Address offset: 0x524
Baud rate. Accuracy depends on the HFCLK source selected.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x04000000 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW BAUDRATE Baud rate
Baud1200 0x0004F000 1200 baud (actual rate: 1205)
Baud2400 0x0009D000 2400 baud (actual rate: 2396)
Baud4800 0x0013B000 4800 baud (actual rate: 4808)
Baud9600 0x00275000 9600 baud (actual rate: 9598)
Baud14400 0x003B0000 14400 baud (actual rate: 14414)
Baud19200 0x004EA000 19200 baud (actual rate: 19208)
Baud28800 0x0075F000 28800 baud (actual rate: 28829)
Baud31250 0x00800000 31250 baud
Baud38400 0x009D5000 38400 baud (actual rate: 38462)
Baud56000 0x00E50000 56000 baud (actual rate: 55944)
Baud57600 0x00EBF000 57600 baud (actual rate: 57762)
Baud76800 0x013A9000 76800 baud (actual rate: 76923)
Baud115200 0x01D7E000 115200 baud (actual rate: 115942)
Baud230400 0x03AFB000 230400 baud (actual rate: 231884)
Baud250000 0x04000000 250000 baud
Baud460800 0x075F7000 460800 baud (actual rate: 470588)
Baud921600 0x0EBED000 921600 baud (actual rate: 941176)
Baud1M 0x10000000 1Mega baud

6.33.10.24 CONFIG
Address offset: 0x56C
Configuration of parity and hardware flow control

4413_417 v1.9 749

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B B B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW HWFC Hardware flow control
Disabled 0 Disabled
Enabled 1 Enabled
B RW PARITY Parity
Excluded 0x0 Exclude parity bit
Included 0x7 Include parity bit
C RW STOP Stop bits
One 0 One stop bit
Two 1 Two stop bits

6.33.11 Electrical specification

6.33.11.1 UART electrical specification

Symbol Description Min. Typ. Max. Units

fUART 42
Baud rate for UART . 1000 kbps

tUART,CTSH CTS high time 1 µs

tUART,START Time from STARTRX/STARTTX task to transmission started 1 µs

6.34 UARTE — Universal asynchronous receiver/

transmitter with EasyDMA
The Universal asynchronous receiver/transmitter with EasyDMA (UARTE) offers fast, full-duplex,
asynchronous serial communication with built-in flow control (CTS, RTS) support in hardware at a rate up
to 1 Mbps, and EasyDMA data transfer from/to RAM.
Listed here are the main features for UARTE:
• Full-duplex operation
• Automatic hardware flow control
• Optional even parity bit checking and generation
• EasyDMA
• Up to 1 Mbps baudrate
• Return to IDLE between transactions supported (when using HW flow control)
• One or two stop bit
• Least significant bit (LSB) first

42
High baud rates may require GPIOs to be set as High Drive, see GPIO for more details.

4413_417 v1.9 750

 Peripherals

PSELRXD PSELCTS PSELRTS PSELTXD

STARTRX RXD STARTTX

TXD
(signal)
STOPRX (signal) STOPTX
RXD.PTR TXD.PTR
SUSPEND

RESUME

ENDTX
RX
RXTO EasyDMA EasyDMA
FIFO CTS
ENDRX NCTS

RAM
RXD TXD
RXD+1 TXD+1
RXD+2 TXD+2
RXD+n TXD+n

Figure 192: UARTE configuration

The GPIOs used for each UART interface can be chosen from any GPIO on the device and are
independently configurable. This enables great flexibility in device pinout and efficient use of board space
and signal routing.

Note: The external crystal oscillator must be enabled to obtain sufficient clock accuracy for stable
communication. See CLOCK — Clock control on page 156 for more information.

6.34.1 EasyDMA
The UARTE implements EasyDMA for reading and writing to and from the RAM.
If the TXD.PTR and the RXD.PTR are not pointing to the Data RAM region, an EasyDMA transfer may result
in a HardFault or RAM corruption. See Memory on page 21 for more information about the different
memory regions.
The .PTR and .MAXCNT registers are double-buffered. They can be updated and prepared for the next RX/
TX transmission immediately after having received the RXSTARTED/TXSTARTED event.
The ENDRX and ENDTX events indicate that the EasyDMA is finished accessing the RX or TX buffer in RAM.

6.34.2 Transmission
The first step of a DMA transmission is storing bytes in the transmit buffer and configuring EasyDMA. This
is achieved by writing the initial address pointer to TXD.PTR, and the number of bytes in the RAM buffer to
TXD.MAXCNT. The UARTE transmission is started by triggering the STARTTX task.
After each byte has been sent over the TXD line, a TXDRDY event will be generated.
When all bytes in the TXD buffer, as specified in the TXD.MAXCNT register, have been transmitted, the
UARTE transmission will end automatically and an ENDTX event will be generated.
A UARTE transmission sequence is stopped by triggering the STOPTX task. A TXSTOPPED event will be
generated when the UARTE transmitter has stopped.
If the ENDTX event has not already been generated when the UARTE transmitter has come to a stop, the
UARTE will generate the ENDTX event explicitly even though all bytes in the TXD buffer, as specified in the
TXD.MAXCNT register, have not been transmitted.
If flow control is enabled through the HWFC field in the CONFIG register, a transmission will be
automatically suspended when CTS is deactivated and resumed when CTS is activated again, as shown in
the following figure. A byte that is in transmission when CTS is deactivated will be fully transmitted before
the transmission is suspended.

4413_417 v1.9 751

 Peripherals

CTS
TXD

0 1 2 N-2 N-1 N

TXDRDY

TXDRDY

TXDRDY

TXDRDY

TXDRDY

TXDRDY
TXSTARTED
Lifeline

1 2
TXD.MAXCNT = N+1

ENDTX
STARTTX

Figure 193: UARTE transmission

The UARTE transmitter will be in its lowest activity level, and consume the least amount of energy, when it
is stopped, i.e. before it is started via STARTTX or after it has been stopped via STOPTX and the TXSTOPPED
event has been generated. See POWER — Power supply on page 80 for more information about power
modes.

6.34.3 Reception
The UARTE receiver is started by triggering the STARTRX task. The UARTE receiver is using EasyDMA to
store incoming data in an RX buffer in RAM.
The RX buffer is located at the address specified in the RXD.PTR register. The RXD.PTR register is double-
buffered and it can be updated and prepared for the next STARTRX task immediately after the RXSTARTED
event is generated. The size of the RX buffer is specified in the RXD.MAXCNT register. The UARTE generates
an ENDRX event when it has filled up the RX buffer, as seen in the following figure.
For each byte received over the RXD line, an RXDRDY event will be generated. This event is likely to occur
before the corresponding data has been transferred to Data RAM.
The RXD.AMOUNT register can be queried following an ENDRX event to see how many new bytes have
been transferred to the RX buffer in RAM since the previous ENDRX event.

4413_417 v1.9 752

 Peripherals

Data RAM

0x20000000
1
0x20000001
2
0x20000002
3
0x20000003
4
0x20000004
5

0x20000010
6
0x20000011
7
0x20000012
8
0x20000013
9
0x20000014
10

0x20000020
11
0x20000021
12
0x20000022
-
0x20000023
-
0x20000024
-
EasyDMA

1 2 3 4 5 6 7 8 9 10 11 12
RXD

1 2 3 4 5 6 7 8 9 10 11 12
RXSTARTED

RXSTARTED

RXSTARTED
ENDRX

ENDRX
RXDRDY

RXDRDY

RXDRDY

RXDRDY

RXDRDY

RXDRDY

RXDRDY

RXDRDY

RXDRDY

RXDRDY

RXDRDY

RXDRDY
Lifeline

1 2 3 4
STARTRX

STARTRX
RXD.PTR = 0x20000000

RXD.PTR = 0x20000010

RXD.PTR = 0x20000020

RXD.PTR = 0x20000030
RXD.MAXCNT = 5
ENDRX_STARTRX = 1

STARTRX

Figure 194: UARTE reception

The UARTE receiver is stopped by triggering the STOPRX task. An RXTO event is generated when the UARTE
has stopped. The UARTE will make sure that an impending ENDRX event will be generated before the RXTO
event is generated. This means that the UARTE will guarantee that no ENDRX event will be generated after
RXTO, unless the UARTE is restarted or a FLUSHRX command is issued after the RXTO event is generated.

Note: If the ENDRX event has not been generated when the UARTE receiver stops, indicating that
all pending content in the RX FIFO has been moved to the RX buffer, the UARTE will generate the
ENDRX event explicitly even though the RX buffer is not full. In this scenario the ENDRX event will
be generated before the RXTO event is generated.

To determine the amount of bytes the RX buffer has received, the CPU can read the RXD.AMOUNT register
following the ENDRX event or the RXTO event.
The UARTE is able to receive up to four bytes after the STOPRX task has been triggered, as long as these
are sent in succession immediately after the RTS signal is deactivated. After the RTS is deactivated, the
UART is able to receive bytes for a period of time equal to the time needed to send four bytes on the
configured baud rate.
After the RXTO event is generated the internal RX FIFO may still contain data, and to move this data to
RAM the FLUSHRX task must be triggered. To make sure that this data does not overwrite data in the RX
buffer, the RX buffer should be emptied or the RXD.PTR should be updated before the FLUSHRX task is
triggered. To make sure that all data in the RX FIFO is moved to the RX buffer, the RXD.MAXCNT register
must be set to RXD.MAXCNT > 4, as seen in the following figure. The UARTE will generate the ENDRX event
after completing the FLUSHRX task even if the RX FIFO was empty or if the RX buffer does not get filled up.
To be able to know how many bytes have actually been received into the RX buffer in this case, the CPU
can read the RXD.AMOUNT register following the ENDRX event.

4413_417 v1.9 753

 Peripherals

EasyDMA
1 2 3 4 5 6 7 8 9 10 11, 12, 13, 14

RXD 1 2 3 4 5 6 7 8 9 10 11 12 13 14

ENDRX

ENDRX
RXSTARTED

RXSTARTED

ENDRX
RXTO
Lifeline

1 2 3 3 4 5

Timeout

STARTRX

ENDRX_STARTRX = 0
STOPRX
RXD.PTR = C
RXD.PTR = B

FLUSHRX
RXD.MAXCNT = 5
RXD.PTR = A
ENDRX_STARTRX = 1

STARTRX

Figure 195: UARTE reception with forced stop via STOPRX

If HW flow control is enabled through the HWFC field in the CONFIG register, the RTS signal will be
deactivated when the receiver is stopped via the STOPRX task or when the UARTE is only able to receive
four more bytes in its internal RX FIFO.
With flow control disabled, the UARTE will function in the same way as when the flow control is enabled
except that the RTS line will not be used. This means that no signal will be generated when the UARTE has
reached the point where it is only able to receive four more bytes in its internal RX FIFO. Data received
when the internal RX FIFO is filled up, will be lost.
The UARTE receiver will be in its lowest activity level, and consume the least amount of energy, when it is
stopped, i.e. before it is started via STARTRX or after it has been stopped via STOPRX and the RXTO event
has been generated. See POWER — Power supply on page 80 for more information about power modes.

6.34.4 Error conditions

An ERROR event, in the form of a framing error, will be generated if a valid stop bit is not detected in a
frame. Another ERROR event, in the form of a break condition, will be generated if the RXD line is held
active low for longer than the length of a data frame. Effectively, a framing error is always generated
before a break condition occurs.
An ERROR event will not stop reception. If the error was a parity error, the received byte will still be
transferred into Data RAM, and so will following incoming bytes. If there was a framing error (wrong stop
bit), that specific byte will NOT be stored into Data RAM, but following incoming bytes will.

6.34.5 Using the UARTE without flow control

If flow control is not enabled, the interface will behave as if the CTS and RTS lines are kept active all the
time.

6.34.6 Parity and stop bit configuration

Automatic even parity generation for both transmission and reception can be configured using the register
CONFIG on page 768. See the register description for details.
The amount of stop bits can also be configured through the register CONFIG on page 768.

6.34.7 Low power

When putting the system in low power and the peripheral is not needed, lowest possible power
consumption is achieved by stopping, and then disabling the peripheral.
The STOPTX and STOPRX tasks may not be always needed (the peripheral might already be stopped), but if
STOPTX and/or STOPRX is sent, software shall wait until the TXSTOPPED and/or RXTO event is received in
response, before disabling the peripheral through the ENABLE register.

4413_417 v1.9 754

 Peripherals

6.34.8 Pin configuration

The different signals RXD, CTS (Clear To Send, active low), RTS (Request To Send, active low), and TXD
associated with the UARTE are mapped to physical pins according to the configuration specified in the
PSEL.RXD, PSEL.CTS, PSEL.RTS, and PSEL.TXD registers respectively.
The PSEL.RXD, PSEL.CTS, PSEL.RTS, and PSEL.TXD registers and their configurations are only used as long
as the UARTE is enabled, and retained only for the duration the device is in ON mode. PSEL.RXD, PSEL.RTS,
PSEL.RTS, and PSEL.TXD must only be configured when the UARTE is disabled.
To secure correct signal levels on the pins by the UARTE when the system is in OFF mode, the pins must be
configured in the GPIO peripheral as described in the following table.
Only one peripheral can be assigned to drive a particular GPIO pin at a time. Failing to do so may result in
unpredictable behavior.

UARTE signal UARTE pin Direction Output value

RXD As specified in PSEL.RXD Input Not applicable
CTS As specified in PSEL.CTS Input Not applicable
RTS As specified in PSEL.RTS Output 1
TXD As specified in PSEL.TXD Output 1

Table 57: GPIO configuration before enabling peripheral

6.34.9 Registers
Instances

Instance Base address Description

UARTE0 0x40002000 Universal asynchronous receiver/transmitter with EasyDMA, unit 0
UARTE1 0x40028000 Universal asynchronous receiver/transmitter with EasyDMA, unit 1

Register overview

Register Offset Description

TASKS_STARTRX 0x000 Start UART receiver
TASKS_STOPRX 0x004 Stop UART receiver
TASKS_STARTTX 0x008 Start UART transmitter
TASKS_STOPTX 0x00C Stop UART transmitter
TASKS_FLUSHRX 0x02C Flush RX FIFO into RX buffer
EVENTS_CTS 0x100 CTS is activated (set low). Clear To Send.
EVENTS_NCTS 0x104 CTS is deactivated (set high). Not Clear To Send.
EVENTS_RXDRDY 0x108 Data received in RXD (but potentially not yet transferred to Data RAM)
EVENTS_ENDRX 0x110 Receive buffer is filled up
EVENTS_TXDRDY 0x11C Data sent from TXD
EVENTS_ENDTX 0x120 Last TX byte transmitted
EVENTS_ERROR 0x124 Error detected
EVENTS_RXTO 0x144 Receiver timeout
EVENTS_RXSTARTED 0x14C UART receiver has started
EVENTS_TXSTARTED 0x150 UART transmitter has started
EVENTS_TXSTOPPED 0x158 Transmitter stopped
SHORTS 0x200 Shortcuts between local events and tasks
INTEN 0x300 Enable or disable interrupt
INTENSET 0x304 Enable interrupt

4413_417 v1.9 755

 Peripherals

Register Offset Description

INTENCLR 0x308 Disable interrupt
ERRORSRC 0x480 Error source

This register is read/write one to clear.

ENABLE 0x500 Enable UART
PSEL.RTS 0x508 Pin select for RTS signal
PSEL.TXD 0x50C Pin select for TXD signal
PSEL.CTS 0x510 Pin select for CTS signal
PSEL.RXD 0x514 Pin select for RXD signal
BAUDRATE 0x524 Baud rate. Accuracy depends on the HFCLK source selected.
RXD.PTR 0x534 Data pointer
RXD.MAXCNT 0x538 Maximum number of bytes in receive buffer
RXD.AMOUNT 0x53C Number of bytes transferred in the last transaction
TXD.PTR 0x544 Data pointer
TXD.MAXCNT 0x548 Maximum number of bytes in transmit buffer
TXD.AMOUNT 0x54C Number of bytes transferred in the last transaction
CONFIG 0x56C Configuration of parity and hardware flow control

6.34.9.1 TASKS_STARTRX
Address offset: 0x000
Start UART receiver

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STARTRX Start UART receiver
Trigger 1 Trigger task

6.34.9.2 TASKS_STOPRX
Address offset: 0x004
Stop UART receiver

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STOPRX Stop UART receiver
Trigger 1 Trigger task

6.34.9.3 TASKS_STARTTX
Address offset: 0x008
Start UART transmitter

4413_417 v1.9 756

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STARTTX Start UART transmitter
Trigger 1 Trigger task

6.34.9.4 TASKS_STOPTX
Address offset: 0x00C
Stop UART transmitter

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STOPTX Stop UART transmitter
Trigger 1 Trigger task

6.34.9.5 TASKS_FLUSHRX
Address offset: 0x02C
Flush RX FIFO into RX buffer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_FLUSHRX Flush RX FIFO into RX buffer
Trigger 1 Trigger task

6.34.9.6 EVENTS_CTS
Address offset: 0x100
CTS is activated (set low). Clear To Send.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_CTS CTS is activated (set low). Clear To Send.
NotGenerated 0 Event not generated
Generated 1 Event generated

6.34.9.7 EVENTS_NCTS
Address offset: 0x104
CTS is deactivated (set high). Not Clear To Send.

4413_417 v1.9 757

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_NCTS CTS is deactivated (set high). Not Clear To Send.
NotGenerated 0 Event not generated
Generated 1 Event generated

6.34.9.8 EVENTS_RXDRDY
Address offset: 0x108
Data received in RXD (but potentially not yet transferred to Data RAM)

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_RXDRDY Data received in RXD (but potentially not yet transferred to Data RAM)
NotGenerated 0 Event not generated
Generated 1 Event generated

6.34.9.9 EVENTS_ENDRX
Address offset: 0x110
Receive buffer is filled up

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_ENDRX Receive buffer is filled up
NotGenerated 0 Event not generated
Generated 1 Event generated

6.34.9.10 EVENTS_TXDRDY
Address offset: 0x11C
Data sent from TXD

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_TXDRDY Data sent from TXD
NotGenerated 0 Event not generated
Generated 1 Event generated

6.34.9.11 EVENTS_ENDTX
Address offset: 0x120
Last TX byte transmitted

4413_417 v1.9 758

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_ENDTX Last TX byte transmitted
NotGenerated 0 Event not generated
Generated 1 Event generated

6.34.9.12 EVENTS_ERROR
Address offset: 0x124
Error detected

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_ERROR Error detected
NotGenerated 0 Event not generated
Generated 1 Event generated

6.34.9.13 EVENTS_RXTO
Address offset: 0x144
Receiver timeout

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_RXTO Receiver timeout
NotGenerated 0 Event not generated
Generated 1 Event generated

6.34.9.14 EVENTS_RXSTARTED
Address offset: 0x14C
UART receiver has started

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_RXSTARTED UART receiver has started
NotGenerated 0 Event not generated
Generated 1 Event generated

6.34.9.15 EVENTS_TXSTARTED
Address offset: 0x150
UART transmitter has started

4413_417 v1.9 759

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_TXSTARTED UART transmitter has started
NotGenerated 0 Event not generated
Generated 1 Event generated

6.34.9.16 EVENTS_TXSTOPPED
Address offset: 0x158
Transmitter stopped

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_TXSTOPPED Transmitter stopped
NotGenerated 0 Event not generated
Generated 1 Event generated

6.34.9.17 SHORTS
Address offset: 0x200
Shortcuts between local events and tasks

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID D C

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
C RW ENDRX_STARTRX Shortcut between event ENDRX and task STARTRX
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
D RW ENDRX_STOPRX Shortcut between event ENDRX and task STOPRX
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut

6.34.9.18 INTEN
Address offset: 0x300
Enable or disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID L J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW CTS Enable or disable interrupt for event CTS
Disabled 0 Disable
Enabled 1 Enable
B RW NCTS Enable or disable interrupt for event NCTS
Disabled 0 Disable
Enabled 1 Enable

4413_417 v1.9 760

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID L J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
C RW RXDRDY Enable or disable interrupt for event RXDRDY
Disabled 0 Disable
Enabled 1 Enable
D RW ENDRX Enable or disable interrupt for event ENDRX
Disabled 0 Disable
Enabled 1 Enable
E RW TXDRDY Enable or disable interrupt for event TXDRDY
Disabled 0 Disable
Enabled 1 Enable
F RW ENDTX Enable or disable interrupt for event ENDTX
Disabled 0 Disable
Enabled 1 Enable
G RW ERROR Enable or disable interrupt for event ERROR
Disabled 0 Disable
Enabled 1 Enable
H RW RXTO Enable or disable interrupt for event RXTO
Disabled 0 Disable
Enabled 1 Enable
I RW RXSTARTED Enable or disable interrupt for event RXSTARTED
Disabled 0 Disable
Enabled 1 Enable
J RW TXSTARTED Enable or disable interrupt for event TXSTARTED
Disabled 0 Disable
Enabled 1 Enable
L RW TXSTOPPED Enable or disable interrupt for event TXSTOPPED
Disabled 0 Disable
Enabled 1 Enable

6.34.9.19 INTENSET
Address offset: 0x304
Enable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID L J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW CTS Write '1' to enable interrupt for event CTS
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW NCTS Write '1' to enable interrupt for event NCTS
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW RXDRDY Write '1' to enable interrupt for event RXDRDY
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

4413_417 v1.9 761

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID L J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
D RW ENDRX Write '1' to enable interrupt for event ENDRX
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
E RW TXDRDY Write '1' to enable interrupt for event TXDRDY
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
F RW ENDTX Write '1' to enable interrupt for event ENDTX
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
G RW ERROR Write '1' to enable interrupt for event ERROR
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
H RW RXTO Write '1' to enable interrupt for event RXTO
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
I RW RXSTARTED Write '1' to enable interrupt for event RXSTARTED
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
J RW TXSTARTED Write '1' to enable interrupt for event TXSTARTED
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
L RW TXSTOPPED Write '1' to enable interrupt for event TXSTOPPED
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.34.9.20 INTENCLR
Address offset: 0x308
Disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID L J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW CTS Write '1' to disable interrupt for event CTS
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW NCTS Write '1' to disable interrupt for event NCTS
Clear 1 Disable
Disabled 0 Read: Disabled

4413_417 v1.9 762

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID L J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Enabled 1 Read: Enabled
C RW RXDRDY Write '1' to disable interrupt for event RXDRDY
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
D RW ENDRX Write '1' to disable interrupt for event ENDRX
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
E RW TXDRDY Write '1' to disable interrupt for event TXDRDY
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
F RW ENDTX Write '1' to disable interrupt for event ENDTX
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
G RW ERROR Write '1' to disable interrupt for event ERROR
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
H RW RXTO Write '1' to disable interrupt for event RXTO
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
I RW RXSTARTED Write '1' to disable interrupt for event RXSTARTED
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
J RW TXSTARTED Write '1' to disable interrupt for event TXSTARTED
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
L RW TXSTOPPED Write '1' to disable interrupt for event TXSTOPPED
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.34.9.21 ERRORSRC
Address offset: 0x480
Error source
This register is read/write one to clear.

4413_417 v1.9 763

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW OVERRUN Overrun error
W1C
A start bit is received while the previous data still lies in RXD. (Previous data
is lost.)
NotPresent 0 Read: error not present
Present 1 Read: error present
B RW PARITY Parity error
W1C
A character with bad parity is received, if HW parity check is enabled.
NotPresent 0 Read: error not present
Present 1 Read: error present
C RW FRAMING Framing error occurred
W1C
A valid stop bit is not detected on the serial data input after all bits in a
character have been received.
NotPresent 0 Read: error not present
Present 1 Read: error present
D RW BREAK Break condition
W1C
The serial data input is '0' for longer than the length of a data frame. (The
data frame length is 10 bits without parity bit, and 11 bits with parity bit).
NotPresent 0 Read: error not present
Present 1 Read: error present

6.34.9.22 ENABLE
Address offset: 0x500
Enable UART

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW ENABLE Enable or disable UARTE
Disabled 0 Disable UARTE
Enabled 8 Enable UARTE

6.34.9.23 PSEL.RTS
Address offset: 0x508
Pin select for RTS signal

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

4413_417 v1.9 764

 Peripherals

6.34.9.24 PSEL.TXD
Address offset: 0x50C
Pin select for TXD signal

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.34.9.25 PSEL.CTS
Address offset: 0x510
Pin select for CTS signal

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.34.9.26 PSEL.RXD
Address offset: 0x514
Pin select for RXD signal

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW PIN [0..31] Pin number
B RW PORT [0..1] Port number
C RW CONNECT Connection
Disconnected 1 Disconnect
Connected 0 Connect

6.34.9.27 BAUDRATE
Address offset: 0x524
Baud rate. Accuracy depends on the HFCLK source selected.

4413_417 v1.9 765

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x04000000 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW BAUDRATE Baud rate
Baud1200 0x0004F000 1200 baud (actual rate: 1205)
Baud2400 0x0009D000 2400 baud (actual rate: 2396)
Baud4800 0x0013B000 4800 baud (actual rate: 4808)
Baud9600 0x00275000 9600 baud (actual rate: 9598)
Baud14400 0x003AF000 14400 baud (actual rate: 14401)
Baud19200 0x004EA000 19200 baud (actual rate: 19208)
Baud28800 0x0075C000 28800 baud (actual rate: 28777)
Baud31250 0x00800000 31250 baud
Baud38400 0x009D0000 38400 baud (actual rate: 38369)
Baud56000 0x00E50000 56000 baud (actual rate: 55944)
Baud57600 0x00EB0000 57600 baud (actual rate: 57554)
Baud76800 0x013A9000 76800 baud (actual rate: 76923)
Baud115200 0x01D60000 115200 baud (actual rate: 115108)
Baud230400 0x03B00000 230400 baud (actual rate: 231884)
Baud250000 0x04000000 250000 baud
Baud460800 0x07400000 460800 baud (actual rate: 457143)
Baud921600 0x0F000000 921600 baud (actual rate: 941176)
Baud1M 0x10000000 1 megabaud

6.34.9.28 RXD
RXD EasyDMA channel

6.34.9.28.1 RXD.PTR
Address offset: 0x534
Data pointer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PTR Data pointer

See the memory chapter for details about which memories are available for
EasyDMA.

6.34.9.28.2 RXD.MAXCNT
Address offset: 0x538
Maximum number of bytes in receive buffer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW MAXCNT [0..0xFFFF] Maximum number of bytes in receive buffer

4413_417 v1.9 766

 Peripherals

6.34.9.28.3 RXD.AMOUNT
Address offset: 0x53C
Number of bytes transferred in the last transaction

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R AMOUNT [0..0xFFFF] Number of bytes transferred in the last transaction

6.34.9.29 TXD
TXD EasyDMA channel

6.34.9.29.1 TXD.PTR
Address offset: 0x544
Data pointer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PTR Data pointer

See the memory chapter for details about which memories are available for
EasyDMA.

6.34.9.29.2 TXD.MAXCNT
Address offset: 0x548
Maximum number of bytes in transmit buffer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW MAXCNT [0..0xFFFF] Maximum number of bytes in transmit buffer

6.34.9.29.3 TXD.AMOUNT
Address offset: 0x54C
Number of bytes transferred in the last transaction

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R AMOUNT [0..0xFFFF] Number of bytes transferred in the last transaction

4413_417 v1.9 767

 Peripherals

6.34.9.30 CONFIG
Address offset: 0x56C
Configuration of parity and hardware flow control

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B B B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW HWFC Hardware flow control
Disabled 0 Disabled
Enabled 1 Enabled
B RW PARITY Parity
Excluded 0x0 Exclude parity bit
Included 0x7 Include even parity bit
C RW STOP Stop bits
One 0 One stop bit
Two 1 Two stop bits

6.34.10 Electrical specification

6.34.10.1 UARTE electrical specification

Symbol Description Min. Typ. Max. Units

fUARTE 43
Baud rate for UARTE . 1000 kbps

tUARTE,CTSH CTS high time 1 µs

tUARTE,START Time from STARTRX/STARTTX task to transmission started 1 µs

6.35 USBD — Universal serial bus device

The USB device (USBD) controller implements a full speed USB device function that meets 2.0 revision of
the USB specification.

43
High baud rates may require GPIOs to be set as High Drive, see GPIO chapter for more details.

4413_417 v1.9 768

 Peripherals

POWER
USBDETECTED Event
USBREMOVED ref
USBPWRRDY generator

LDO VBUS

tasks DECUSB
events
Registers
USBD
MAC
APB

HFXO PLL Serial Physcial D+

AHB

Flash interface layer (PHY)/

engine Transceiver D-
(SIE)
EasyDMA
EasyDMA
EasyDMA
Data RAM for each endpoint

Local
buffers

Figure 196: USB device block diagram

Listed here are the main features for USBD:

• Full-speed (12 Mbps) device fully compliant to Universal Serial Bus Specification Revision 2.0, including
following engineering change notices (ECNs) issued by USB Implementers Forum:
• Pull-up/pull-down Resistors ECN
• 5V Short Circuit Withstand Requirement Change ECN
• USB device stack available in the Nordic SDK
• Integrated (on-chip) USB transceiver (PHY)
• Software controlled on-chip pull-up on D+
• Endpoints:
• Two control (1 IN, 1 OUT)
• 14 bulk/interrupt (7 IN, 7 OUT)
• Two isochronous (1 IN, 1 OUT)
• Double buffering for isochronous (ISO) endpoints (IN/OUT) support
• USB suspend, resume, and remote wake-up support
• 64 bytes buffer size for each bulk/interrupt endpoint
• Up to 1023 bytes buffer size for ISO endpoints
• EasyDMA for all data transfers

6.35.1 USB device states

The behavior of a USB device can be modelled through a state diagram.
The USB 2.0 Specification (see Chapter 9 USB Device Framework) defines a number of states for a USB
device, as shown in the following figure.

4413_417 v1.9 769

 Peripherals

Attached

USB power USB power

lost applied

Bus inactive

Powered Suspended
Bus activity

Momentary
power
interruption USB reset

Bus inactive

Default Suspended
Bus activity

USB reset

Address
assigned

Bus inactive

Address Suspended
Bus activity

Device Device
deconfigured configured

Bus inactive

Configured Suspended
Bus activity

Figure 197: Device state diagram

The device must change state according to host-initiated traffic and USB bus states. It is up to the software
to implement a state machine that matches the above definition. To detect the presence or absence of
USB supply (VBUS), two events USBDETECTED and USBREMOVED can be used to implement the state
machine. For more details on these events, see USB supply on page 85.
As a general rule when implementing the software, the host behavior shall never be assumed to be
predictable. In particular the sequence of commands received during an enumeration. The software shall
always react to the current bus conditions or commands sent by the host.

6.35.2 USB terminology

The USB specification defines bus states, rather than logic levels on the D+ and D- lines.
For a full speed device, the bus state where the D+ line is high and the D- line is low is defined as the J
state. The bus state where D+ is low and D- high is called the K state.
An idle bus, where D+ and D- lines are only polarized through the pull-up on D+ and pull-downs on the
host side, will be in J state.
Both lines low are called SE0 (single-ended 0), and both lines high SE1 (single-ended 1).

4413_417 v1.9 770

 Peripherals

6.35.3 USB pins

The USBD peripheral features a number of dedicated pins.
The dedicated USB pins can be grouped in two categories, signal and power. The signal pins consist of the
D+ and D- pins, which are to be connected to the USB host. They are dedicated pins, and not available as
standard GPIOs. The USBD peripheral is implemented according to the USB specification revision 2.0, 5V
Short Circuit Withstand ECN Requirement Change, meaning these two pins are not 5 V tolerant.
The signal pins and the pull-up will operate only while VBUS is in its valid voltage range, and USBD is
enabled through the ENABLE register. For details on the USB power supply and VBUS detection, see USB
supply on page 85.
For more information about the pinout, see Pin assignments on page 845.

6.35.4 USBD power-up sequence

The physical layer interface (PHY)/USB transceiver is powered separately from the rest of the device (VBUS
pin), which has some implications on the USBD power-up sequence.
The device is not able to properly signal its presence to the USB host and handle traffic from the host,
unless the PHY's power supply is enabled and stable. Turning the PHY's power supply on/off is directly
linked to register ENABLE. The device provides events that help synchronizing software to the various
steps during the power-up sequence.
To make sure that all resources in USBD are available and the dedicated USB voltage regulator stabilized,
the following is recommended:
• Enable USBD only after VBUS has been detected
• Turn the USB pull-up on after the following events have occurred:
• USBPWRRDY
• USBEVENT, with the READY condition flagged in EVENTCAUSE
The following sequence chart illustrates a typical handling of VBUS power-up:

VBUS POWER CLOCK Software USBD

VBUS in valid range

USBDETECTED

ENABLE=Enabled

HFCLKSTART

HFCLK Crystal
oscillator now starting
USBEVENT
EVENTCAUSE=READY
USBD has been
initialized, but PHY has
not powered up
USBPWRRDY

PHY is now powered

HFCLKSTARTED

USBPULLUP=Enabled

Enumeration starts

Figure 198: VBUS power-up sequence

Upon detecting VBUS removal, it is recommended to wait for ongoing EasyDMA transfers to finish before
disabling USBD (relevant ENDEPIN[n], ENDISOIN, ENDEPOUT[n], or ENDISOOUT events, see EasyDMA on
page 774). The USBREMOVED event, described in USB supply on page 85, signals when the VBUS is
removed. Reading the ENABLE register will return Enabled until USBD is completely disabled.

4413_417 v1.9 771

 Peripherals

6.35.5 USB pull-up

The USB pull-up serves two purposes: it indicates to the host that the device is connected to the USB bus,
and it indicates the device's speed capability.
When no pull-up is connected to the USB bus, the host sees both D+ and D- lines low, as they are pulled
down on the host side by 15 kΩ resistors. The device is not detected by the host, putting it in a detached
state even if it is physically connected to the host. In this situation, the device is not allowed to draw
current from VBUS, according to USB 2.0 Specification.
When a full-speed device connects its 1.5 kΩ pull-up to D+, the host sees the corresponding line high. The
device is then in the attached state. During the enumeration process, the host attempts to determine if
the full-speed device also supports higher speeds and initiates communication with the device to further
identify it. The USBD peripheral implemented in this device supports only full-speed operation (12 Mbps),
and thus ignores the negotiation for higher speeds in accordance with USB 2.0 Specification.
Register USBPULLUP enables software to connect or disconnect the pull-up on D+. This allows the
software to control when USB enumeration takes place. It also allows to emulate a physical disconnect
from the USB bus, for instance when re-enumeration is required. USBPULLUP has to be enabled to allow
the USBD to handle USB traffic and generate appropriate events. This forbids the use of an external pull-
up.
Note that disconnecting the pull-up through register USBPULLUP while connected to a host, will result in
both D+ and D- lines to be pulled low by the host's pull-down resistors. However, as mentioned above, this
will also inhibit the generation of the USBRESET event. The pull-up is disabled by default after a chip reset.
The pull-up shall only get connected after USBD has been enabled through register ENABLE. The USB
pull-up value is automatically changed depending on the bus activity, as specified in Resistor ECN which
amends the original USB 2.0 Specification. The user does not have access to this function as it is handled in
hardware.
While they should never be used in normal traffic activity, lines D+ and D- may at any time be forced into
state specified in register DPDMVALUE by the task DPDMDRIVE. The DPDMNODRIVE task stops driving
them, and PHY returns to normal operation.

6.35.6 USB reset

The USB specification defines a USB reset, which is not be confused with a chip reset. The USB reset is a
normal USB bus condition, and is used as part of the enumeration sequence, it does not reset the chip.
The USB reset results from a single-ended low state (SE0) on lines D+/D- for a tUSB,DETRST amount of time.
Only the host is allowed to drive a USB reset condition on the bus. The UBSD peripheral automatically
interprets a SE0 longer than tUSB,DETRST as a USB reset. When the device detects a USB reset and generates
a USBRESET event, the device USB stack and related parts of the application shall re-initialize themselves,
and go back to the default state.
Some of the registers in the USBD peripheral get automatically reset to a known state, in particular all data
endpoints are disabled and the USBADDR reset to 0.
After the device has connected to the USB bus (i.e. after VBUS is applied), the device shall not respond to
any traffic from the time the pull-up is enabled until it has seen a USB reset condition. This is automatically
ensured by the USBD.
After a USB reset, the device shall be fully responsive after at most TRSTRCY (according to chapter 7 in the
USB specification). Software shall take into account this time that takes the hardware to recover from a
USB reset condition.

4413_417 v1.9 772

 Peripherals

6.35.7 USB suspend and resume

Normally, the host will maintain activity on the USB at least every millisecond according to USB
specification. A USB device will enter suspend when there is no activity on the bus (idle) for a given time.
The device will resume operation when it receives any non idle signalling.
To signal that the device shall go into low power mode (suspend), the host stops activity on the USB bus,
which becomes idle. Only the device pull-up and host pull-downs act on D+ and D-, and the bus is thus
kept at a constant J state. It is up to the device to detect this lack of activity, and enter the low power
mode (suspend) within a specified time.
The USB host can decide to suspend or resume USB activity at any time. If remote wake-up is enabled, the
device may signal to the host to resume from suspend.

6.35.7.1 Entering suspend

The USBD peripheral automatically detects lack of activity for more than a defined amount of time, and
performs steps needed to enter suspend.
When no activity has been detected for longer than tUSB,SUSPEND, the USBD generates the USBEVENT event
with SUSPEND bit set in register EVENTCAUSE. The software shall ensure that the current drawn from
the USB supply line VBUS is within the specified limits before T2SUSP, as defined in chapter 7 of the USB
specification. In order to reduce idle current of USBD, the software must explicitly place the USBD in low
power mode through writing LowPower to register LOWPOWER.
In order to save power, and provided that no other peripheral needs it, the crystal oscillator (HFXO) in
CLOCK may be disabled by software during the USB suspend, while the USB pull-up is disconnected, or
when VBUS is not present. Software must explicitly enable it at any other time. The USBD will not be able
to respond to USB traffic unless HFXO is enabled and stable.

6.35.7.2 Host-initiated resume

Once the host resumes the bus activity, it has to be responsive to incoming requests on the USB bus
within the time TRSMRCY (as defined in chapter 7 of the USB specification) and revert to normal power
consumption mode.
If the host resumes bus activity with or without a RESUME condition (in other words: bus activity is
defined as any non-J state), the USBD peripheral will generate a USBEVENT event, with RESUME bit set
in register EVENTCAUSE. If the host resumes bus activity simply by restarting sending frames, the USBD
peripheral will generate SOF events.

6.35.7.3 Device-initiated remote wake-up

Assuming the remote wake-up is supported by the device and enabled by the host, the device can request
the host to resume from suspend if wake-up condition is met.
To do so, the HFXO needs to be enabled first. After waking up the HFXO, the software must bring USBD out
of the low power mode and into the normal power consumption mode through writing ForceNormal
in register LOWPOWER. It can then instruct the USBD peripheral to drive a RESUME condition (K state)
on the USB bus by triggering the DPDMDRIVE task, and hence attempt to wake up the host. By choosing
Resume in DPDMVALUE, the duration of the RESUME state is under hardware control (tUSB,DRIVEK). By
choosing J or K, the duration of that state is under software control (the J or K state is maintained until a
DPDMNODRIVE task is triggered) and has to meet TDRSMUP as specified in USB specification chapter 7.
Upon writing the ForceNormal in register LOWPOWER, a USBEVENT event is generated with the
USBWUALLOWED bit set in register EVENTCAUSE.
The value in register DPDMVALUE on page 821 will only be captured and used when the DPDMDRIVE
task is triggered. This value defines the state the bus will be forced into after the DPDMDRIVE task.

4413_417 v1.9 773

 Peripherals

The device shall ensure that it does not initiate a remote wake-up request before TWTRSM (according to
USB specification chapter 7) after the bus has entered idle state. Using the recommended resume value in
DPDMVALUE (rather than K) takes care of this, and postpones the RESUME state accordingly.

6.35.8 EasyDMA
The USBD peripheral implements EasyDMA for accessing memory without CPU involvement.
Each endpoint has an associated set of registers, tasks and events. EasyDMA and traffic on USB are tightly
related. A number of events provide insight of what is happening on the USB bus with a number of tasks
allowing an automated response to the traffic.

Note: Endpoint 0 (IN and OUT) are implemented as control endpoint. For more information, see
Control transfers on page 775.

Registers
Enabling endpoints is controlled through the EPINEN and EPOUTEN registers.
The following registers define the memory address of the buffer for a specific IN or OUT endpoint:
• EPIN[n].PTR, (n=0..7)
• EPOUT[n].PTR, (n=0..7)
• ISOIN.PTR
• ISOOUT.PTR
The following registers define the amount of bytes to be sent on USB for next transaction:
• EPIN[n].MAXCNT, (n=0..7)
• ISOIN.MAXCNT
The following registers define the length of the buffer (in bytes) for next transfer of incoming data:
• EPOUT[n].MAXCNT, (n=1..7)
• ISOOUT.MAXCNT
Since the host decides how many bytes are sent over USB, the MAXCNT value can be copied from register
SIZE.EPOUT[n] (n=1..7) or register SIZE.ISOOUT.
Register EPOUT[0].MAXCNT defines the length of the OUT buffer (in bytes) for the control endpoint 0.
Register SIZE.EPOUT[0] shall indicate the same value as MaxPacketSize from the device descriptor or
wLength from the SETUP command, whichever is the least.
The .AMOUNT registers indicate how many bytes actually have been transferred over EasyDMA during the
last transfer.
Stalling bulk/interrupt endpoints is controlled through the EPSTALL register.

Note: Due to USB specification requirements, the effect of the stalling control endpoint 0 may be
overridden by hardware, in particular when a new SETUP token is received.

EasyDMA will not copy the SETUP data to memory (it will only transfer data from the data stage). The
following are separate registers in the USBD peripheral that have setup data.
• BMREQUESTTYPE
• BREQUEST
• WVALUEL
• WVALUEH
• WINDEXL
• WINDEXH

4413_417 v1.9 774

 Peripherals

• WLENGTHL
• WLENGTHH
The EVENTCAUSE register provides details on what caused a given USBEVENT event, for instance if a CRC
error is detected during a transaction, or if bus activity stops or resumes.

Tasks
Tasks STARTEPIN[n], STARTEPOUT[n] (n=0..7), STARTISOIN, and STARTISOOUT capture the values for .PTR
and .MAXCNT registers. For IN endpoints, a transaction over USB gets automatically triggered when the
EasyDMA transfer is complete. For OUT endpoints, it is up to software to allow the next transaction over
USB. See the examples in Control transfers on page 775, Bulk and interrupt transactions on page 778,
and Isochronous transactions on page 780.
For the control endpoint 0, OUT transactions are allowed through the EP0RCVOUT task. The EP0STATUS
task allows a status stage to be initiated, and the EP0STALL task allows stalling further traffic (data or
status stage) on the control endpoint.

Events
The STARTED event confirms that the values of the .PTR and .MAXCNT registers of the endpoints flagged in
register EPSTATUS have been captured. Those can then be modified by software for the next transfer.
Events ENDEPIN[n], ENDEPOUT[n] (n=0..7), ENDISOIN, and ENDISOOUT events indicate that the entire
buffer has been consumed. The buffer can be accessed safely by the software.
Only a single EasyDMA transfer can take place in USBD at any time. Software must ensure that tasks
STARTEPIN[n] (n=0..7), STARTISOIN , STARTEPOUT[n] (n=0..7), or STARTISOOUT are not triggered before
events ENDEPIN[n] (n=0..7), ENDISOIN, ENDEPOUT[n] (n=0..7), or ENDISOOUT are received from an on-
going transfer.
The EPDATA event indicates that a successful (acknowledged) data transaction has occurred on the data
endpoint(s) flagged in register EPDATASTATUS. A successful (acknowledged) data transaction on endpoint
0 is signalled by the EP0DATADONE event.
At any time a USBEVENT event may be sent, with details provided in EVENTCAUSE register.
The EP0SETUP event indicates that a SETUP token has been received on the control endpoint 0, and that
the setup data is available in the setup data registers.

6.35.9 Control transfers

The USB specification mandates every USB device to implement endpoint 0 IN and OUT as control
endpoints.
A control transfer consists of two or three stages:
• Setup stage
• Data stage (optional)
• Status stage
Each control transfer can be one of following types:
• Control read
• Control read no data
• Control write
• Control write no data
An EP0SETUP event indicates that the data in the setup stage (following the SETUP token) is available in
registers.

4413_417 v1.9 775

 Peripherals

The data in the data stage (following the IN or OUT token) is transferred from or to the desired location
using EasyDMA.
The control endpoint buffer can be of any size.
After receiving the SETUP token, the USB controller will not accept (NAK) any incoming IN or OUT tokens
until the software has finished decoding the command, determined the type of transfer, and prepared for
the next stage (data or status) appropriately.
The software can stall a command when in the data and status stages, through the EP0STALL task, when
the command is not supported or if its wValue, wIndex or wLength parameters are wrong. The following
shows a stalled control read transfer, but the same mechanism (tasks) applies to stalling a control write
transfer.
Setup stage Data stage

USB host SETUP 8 bytes IN IN

USB device ACK NAK STALL

EP0SETUP

EP0STALL
Events & tasks

Software
Decode setup

(Command not supported)

EP0STALL=1

Figure 199: Control read gets stalled

See the USB 2.0 Specification and relevant class specifications for rules on stalling commands.

Note: The USBD peripheral handles the SetAddress transfer by itself. As a consequence, the
software shall not process this command other than updating its state machine (see Device state
diagram), nor initiate a status stage. If necessary, the address assigned by the host can be read out
from the USBADDR register after the command has been processed.

6.35.9.1 Control read transfer

This section describes how the software behaves when responding to a control read transfer.
As mentioned earlier, the USB controller will not accept (NAK) any incoming IN tokens until software has
finished decoding the command, determining the type of transfer, and preparing for the next stage (data
or status) appropriately.
For a control read, transferring the data from memory into USBD will trigger a valid, acknowledged (ACK)
IN transaction on USB.
The software has to prepare EasyDMA by pointing to the buffer containing the data to be transferred. If no
other EasyDMA transfers are on-going with USBD, the software can send the STARTEPIN0 task, which will
initiate the data transfer and transaction on USB.
A STARTED event (with EPIN0 bit set in the EPSTATUS register) will be generated as soon as the EPIN[0].PTR
and .MAXCNT registers have been captured. Software may then prepare them for the next data
transaction.

4413_417 v1.9 776

 Peripherals

An ENDEPIN[0] event will be generated when the data has been transferred from memory to the USBD
peripheral.
Finally, an EP0DATADONE event will be generated when the data has been transmitted over USB and
acknowledged by the host.
The software can then either prepare and transmit the next data transaction by repeating the above
sequence, or initiate the status stage through the EP0STATUS task.
Setup stage Data stage Status stage

USB host SETUP 8 bytes IN IN IN ACK IN IN IN ACK OUT DATA (0)

USB device ACK NAK NAK DATA (n) NAK NAK DATA (n+1) ACK
STARTEPIN[0]

EP0DATADONE

STARTEPIN[0]

EP0DATADONE
EP0SETUP

STARTED

ENDEPIN[0]

STARTED

ENDEPIN[0]

EP0STATUS
Events & tasks

Software
Decode setup
EPIN[0].PTR=0xnnnnnnnn
EPIN[0].MAXCNT = MaxPacketSize
STARTEPIN[0]=1

(EPIN[0].PTR=0xnnnnnnnn+64)
EPIN[0].MAXCNT = <MaxPacketSize
STARTEPIN[0]=1
(enable EP0DATADONE to EP0STATUS)

Allow status stage

EP0STATUS=1
Figure 200: Control read transfer

It is possible to enable a shortcut from the EP0DATADONE event to the EP0STATUS task, typically if the
data stage is expected to take a single transfer. If there is no data stage, the software can initiate the status
stage through the EP0STATUS task right away, as as shown in the following figure.
Setup stage Status stage

USB host SETUP 8 bytes OUT DATA (0) OUT DATA (0)

USB device ACK NAK ACK

EP0SETUP

EP0STATUS

Events & tasks

Software
Decode setup

Prepare for status stage

EP0STATUS=1

Figure 201: Control read no data transfer

6.35.9.2 Control write transfer

This section describes how the software responds to a control write transfer.
The software has to prepare EasyDMA by pointing to the buffer in memory that shall contain the incoming
data. If no other EasyDMA transfers are ongoing with USBD, the software can then send the EP0RCVOUT
task, which will make USBD acknowledge (ACK) the first OUT+DATA transaction from the host.
An EP0DATADONE event will be generated when a new OUT+DATA has been transmitted over USB, and is
about to get acknowledged by the device.
After receiving the first transaction, a STARTED event (the EPOUT0 bit set in the EPSTATUS register) is
generated when the EPOUT[0].PTR and .MAXCNT registers have been captured. Software may then
prepare them for the next data transaction.

4413_417 v1.9 777

 Peripherals

An ENDEPOUT[0] event will be generated when the data has been transferred from the USBD peripheral
to memory. The software can then either prepare to receive the next data transaction by repeating the
above sequence, or initiate the status stage through the EP0STATUS task. Until then, further incoming OUT
+DATA transactions get a NAK response by the device.
Setup stage Data stage Status stage

USB host SETUP 8 bytes OUT DATA (m) OUT DATA (n) OUT DATA (n) IN IN IN ACK

USB device ACK ACK NAK ACK NAK NAK DATA (0)

EP0DATADONE

EP0DATADONE
STARTEPOUT[0]

STARTEPOUT[0]
EP0RCVOUT

EP0RCVOUT
EP0SETUP

STARTED

ENDEPOUT[0]

STARTED

ENDEPOUT[0]

EP0STATUS
Events & tasks

Software
Decode setup
EP0RCVOUT=1
EPOUT[0].PTR=0xnnnnnnnn
EPOUT[0].MAXCNT = MaxPacketSize
(enable EP0DATADONE to STARTEP0OUT)
(enable ENDEPOUT[0] to EP0RCVOUT)

STARTEPOUT[0]=1

(EP0RCVOUT=1)

(disable EP0DATADONE to STARTEP0OUT)

(disable ENDEPOUT[0] to EP0RCVOUT)
(enable ENDEPOUT[0] to EP0STATUS)

(EP0STATUS=1)
Figure 202: Control write transfer
Setup stage Status stage

USB host SETUP 8 bytes IN IN ACK

USB device ACK NAK DATA (0)

EP0SETUP

EP0STATUS

Events & tasks

Software
Decode setup

EP0STATUS=1

Figure 203: Control write no data transfer

6.35.10 Bulk and interrupt transactions

The USBD peripheral implements seven pairs of bulk/interrupt endpoints.
The bulk/interrupt endpoints have a fixed USB endpoint number, summarized in the following table.

Bulk endpoint # USB IN endpoint USB OUT endpoint

[1] 0x81 0x01
[2] 0x82 0x02
[3] 0x83 0x03
[4] 0x84 0x04
[5] 0x85 0x05
[6] 0x86 0x06
[7] 0x87 0x07

Table 58: Bulk/interrupt endpoint numbering

A bulk/interrupt transaction consists of a single data stage. Two consecutive, successful transactions are
distinguished through alternating leading process ID (PID): DATA0 follows DATA1, DATA1 follows DATA0,
etc. A repeated transaction is detected by re-using the same PID as previous transaction, i.e DATA0 follows
DATA0, or DATA1 follows DATA1.
The USBD controller automatically toggles DATA0/DATA1 PIDs for every bulk/interrupt transaction.

4413_417 v1.9 778

 Peripherals

If incoming data is corrupted (CRC does not match), the USBD controller automatically prevents DATA0/
DATA1 from toggling, to request the host to resend the data.
In some specific cases, the software may want to force a data toggle (usually reset) on a specific IN
endpoint, or force the expected toggle on an OUT endpoint, for instance as a consequence of the host
issuing ClearFeature, SetInterface, or selecting an alternate setting. Controlling the data toggle
of data IN or OUT endpoint n (n=1..7) is done through register DTOGGLE.
The bulk/interrupt transaction in USB full-speed can be of any size up to 64 bytes. It must be a multiple of
four bytes and 32-bit aligned in memory.
When the USB transaction has completed, an EPDATA event is generated. Until new data has been
transferred by EasyDMA from memory to the USBD peripheral (signalled by the ENDEPIN[n] event), the
hardware will automatically respond with NAK to all incoming IN tokens. Software has to configure and
start the EasyDMA transfer once it is ready to send more data.
Each IN or OUT data endpoint has to be explicitly enabled by software through register EPINEN or
EPOUTEN, according to the configuration declared by the device and selected by the host through the
SetConfig command.
A disabled data endpoint will not respond to any traffic from the host. An enabled data endpoint will
normally respond NAK or ACK (depending on the readiness of the buffers), or STALL (if configured in
register EPSTALL), in which case the endpoint is asked to halt. The halted (or not) state of a given endpoint
can be read back from register HALTED.EPIN[n] or HALTED.EPOUT[n]. The format of the returned 16-bit
value can be copied as is, as a response to a GetStatusEndpoint request from the host.
Enabling or disabling an endpoint will not change its halted state. However, a USB reset will disable and
clear the halted state of all data endpoints.
The control endpoint 0 IN and OUT can also be enabled and/or halted using the same mechanisms, but
due to USB specification, receiving a SETUP will override its state.

6.35.10.1 Bulk and interrupt IN transaction

The host issues IN tokens to receive bulk/interrupt data. In order to send data, the software has to enable
the endpoint and prepare an EasyDMA transfer on the desired endpoint.
Bulk/interrupt IN endpoints are enabled or disabled through their respective INn bit (n=1..7) in EPINEN
register.
It is also possible to stall or resume communication on an endpoint through the EPSTALL register.

USB host IN IN IN ACK

USB device NAK NAK DATA (0)

STARTEPIN[1]

STARTED

EPDATA
ENDEPIN[1]

Events & tasks

Software
Prepare outgoing data

(EPIN[1].PTR=0xnnnnnnnn
EPIN[1].MAXCNT = <MaxPacketSize
STARTEPIN[1]=1

Figure 204: Bulk/interrupt IN transaction

4413_417 v1.9 779

 Peripherals

It is possible (and in some situations it is required) to respond to an IN token with a zero-length data
packet.

Note: On many USB hosts, not responding (DATA+ACK or NAK) to three IN tokens on an interrupt
endpoint would have the host disable that endpoint as a consequence. Re-enumerating the
device (unplug-replug) may be required to restore functionality. Make sure that the relevant data
endpoints are enabled for normal operation as soon as the device gets configured through a
SetConfig request.

6.35.10.2 Bulk and interrupt OUT transaction

When the host wants to transmit bulk/interrupt data, it issues an OUT token (packet) followed by a DATA
packet on a given endpoint n (n=1..7).
A NAK is returned until the software writes any value to register SIZE.EPOUT[n], indicating that the content
of the local buffer can be overwritten. Upon receiving the next OUT+DATA transaction, an ACK is returned
to the host while an EPDATA event is generated (and the EPDATASTATUS register flags are set to indicate
on which endpoint this happened). Once the EasyDMA is prepared and enabled, by writing the EPOUT[n]
registers and triggering the STARTEPOUT[n] task, the incoming data will be transferred to memory. Until
that transfer is finished, the hardware will automatically NAK any other incoming OUT+DATA packets. Only
when the EasyDMA transfer is done (signalled by the ENDEPOUT[n] event), or as soon as any values are
written by the software in register SIZE.EPOUT[n], the endpoint n will accept incoming OUT+DATA again.
It is allowed for the host to send zero-length data packets.
Bulk/interrupt OUT endpoints are enabled or disabled through their respective OUTn bit (n=1..7) in
the EPOUTEN register. It is also possible to stall or resume communication on an endpoint through the
EPSTALL register.
USB host OUT DATA (n) OUT DATA (n) OUT DATA (n+1) OUT DATA (n+1)

USB device NAK ACK NAK ACK

STARTEPOUT[1]
EPDATA

ENDEPOUT[1]

EPDATA
STARTED

Events & tasks

Software
SIZE.EPOUT[1]=0

EPOUT[1].PTR=0xnnnnnnnn
EPOUT[1].MAXCNT=SIZE.EPOUT[1]
STARTEPOUT[1]=1

Process data
EPDATASTATUS.EPOUT1 set (Started)

Figure 205: Bulk/interrupt OUT transaction

6.35.11 Isochronous transactions

The USBD peripheral implements isochronous (ISO) endpoints.
The ISO endpoints have a fixed USB endpoint number, summarized in the following table.

ISO endpoint # USB IN endpoint USB OUT endpoint

[0] 0x88 0x08

Table 59: Isochronous endpoint numbering

An isochronous transaction consists of a single, non-acknowledged data stage. The host sends out a start
of frame at a regular interval (1 ms), and data follows IN or OUT tokens within each frame.

4413_417 v1.9 780

 Peripherals

EasyDMA allows transferring ISO data directly from and to memory. EasyDMA transfers must be initiated
by the software, which can synchronize with the SOF (start of frame) events.
Because the timing of the start of frame is very accurate, the SOF event can be used for jobs such as
synchronizing a local timer through the SOF event and PPI. The SOF event gets synchronized to the 16 MHz
clock prior to being made available to the PPI.
Every start of frame increments a free-running counter, which can be read by software through the
FRAMECNTR register.
Each IN or OUT ISO data endpoint has to be explicitly enabled by software through register EPINEN or
EPOUTEN, according to the configuration declared by the device and selected by the host through the
SetConfig command. A disabled ISO IN data endpoint will not respond to any traffic from the host. A
disabled ISO OUT data endpoint will ignore any incoming traffic from the host.
The USBD peripheral has an internal 1 kB buffer associated with ISO endpoints. The user can either
allocate the full amount to the IN or the OUT endpoint, or split the buffer allocation between the two
using register ISOSPLIT.
The internal buffer also sets the maximum size of the ISO OUT and ISO IN transfers: 1023 bytes when the
full buffer is dedicated to either ISO OUT or ISO IN, and half when the buffer is split between the two.

6.35.11.1 Isochronous IN transaction

When the host wants to receive isochronous (ISO) data, it issues an IN token on the isochronous endpoint.
After the data has been transferred using the EasyDMA, the USB controller on the isochronous IN
endpoint responds to the IN token with the transferred data using the ISOIN.MAXCNT for the size of the
packet.
The ISO IN data endpoint has to be explicitly enabled by software through the ISOIN0 bit in register
EPINEN.
When an ISO IN endpoint is enabled and no data transferred with EasyDMA, the response of the USBD
depends on the setting of the RESPONSE field in register ISOINCONFIG. It can either provide no response
to an IN token or respond with a zero-length data.
If the EasyDMA transfer on the isochronous endpoint is not completed before the next SOF event, the
result of the transfer is undefined.
The maximum size of an ISO IN transfer in USB full-speed is 1023 bytes. The data buffer has to be a
multiple of 4 bytes 32-bit aligned in memory. However, the amount of bytes transferred on the USB data
endpoint can be of any size (up to 1023 bytes, if not shared with an OUT ISO endpoint).
Start of frame Start of frame

response depends on the RESPONSE field in the

USB host IN IN
ISOINCONFIG register
USB device DATA(0) DATA n
SOF

STARTISOIN

STARTED

ENDISOIN

SOF

STARTISOIN

Events & tasks

Software
Prepare outgoing ISO data n

ISOIN.PTR=0xnnnnnnnn
ISOIN.MAXCNT=yy
STARTISOIN=1

Prepare outgoing ISO data n+1

ISOIN.PTR=0xnnnnnnnn
ISOIN.MAXCNT=yy
STARTISOIN=1

Figure 206: Isochronous IN transfer

4413_417 v1.9 781

 Peripherals

6.35.11.2 Isochronous OUT transaction

When the host wants to send isochronous (ISO) data, it issues an OUT token on the isochronous endpoint,
followed by data.
The ISO OUT data endpoint has to be explicitly enabled by software through the ISOOUT0 bit in register
EPOUTEN.
The amount of last received ISO OUT data is provided in the SIZE.ISOOUT register. Software shall interpret
the ZERO and SIZE fields as presented in the following table.

ZERO SIZE Last received data size

Normal 0 No data received at all
Normal 1..1023 1..1023 bytes of data received
ZeroData (not of interest) Zero-length data packet received

Table 60: ISO OUT incoming data size

When EasyDMA is prepared and started, triggering a STARTISOOUT task initiates an EasyDMA transfer to
memory. Software shall synchronize ISO OUT transfers with the SOF events. EasyDMA uses the address in
ISOOUT.PTR and size in ISOOUT.MAXCNT for every new transfer.
If the EasyDMA transfer on the isochronous endpoint is not completed before the next SOF event, the
result of the transfer is undefined.
The maximum size of an isochronous OUT transfer in USB full-speed is 1023 bytes. The data buffer has to
be a multiple of 4 bytes and 32-bit aligned in Data RAM. However, the amount of bytes transferred on the
USB data endpoint can be of any size (up to 1023 bytes if not shared with an IN ISO endpoint).
If the last received ISO data packet is corrupted (wrong CRC), the USB controller generates an USBEVENT
event (at the same time as SOF) and indicates a CRC error on ISOOUTCRC in register EVENTCAUSE.
EasyDMA will transfer the data anyway if it has been set up properly.
Start of frame Start of frame Start of frame

USB host OUT DATA n OUT DATA n+1 OUT DATA n+2

USB device
STARTISOOUT

STARTISOOUT
ENDISOOUT
SOF

STARTED
SOF

SOF

Events & tasks

Software
Prepare for receiving ISO data n
(ISOOUT.MAXCNT=SIZE.ISOOUT)
ISOOUT.PTR=0xnnnnnnnn

(enable SOF to STARTISOOUT)

ISOOUT.MAXCNT=SIZE.ISOOUT
(STARTISOOUT=1)

ISOOUT.PTR=0xnnnnnnnn + size
ISOOUT.MAXCNT=SIZE.ISOOUT

Process data

Figure 207: Isochronous OUT transfer

4413_417 v1.9 782

 Peripherals

6.35.12 USB register access limitations

Some of the registers in USBD cannot be accessed in specific conditions.
This may be the case when USBD is not enabled (using the ENABLE register) and ready (signalled by the
READY bit in EVENTCAUSE after a USBEVENT event), or when USBD is in low power mode while the USB
bus is suspended.
Triggering any tasks, including the tasks triggered through the PPI, is affected by this behavior. In addition,
the following registers are affected:
• HALTED.EPIN[0..7]
• HALTED.EPOUT[0..7]
• USBADDR
• BMREQUESTTYPE
• BREQUEST
• WVALUEL
• WVALUEH
• WINDEXL
• WINDEXH
• WLENGTHL
• WLENGTHH
• SIZE.EPOUT[0..7]
• SIZE.ISOOUT
• USBPULLUP
• DTOGGLE
• EPINEN
• EPOUTEN
• EPSTALL
• ISOSPLIT
• FRAMECNTR

6.35.13 Registers
Instances

Instance Base address Description

USBD 0x40027000 Universal serial bus device

Register overview

Register Offset Description

TASKS_STARTEPIN[0] 0x004 Captures the EPIN[0].PTR and EPIN[0].MAXCNT registers values, and enables endpoint IN 0 to
respond to traffic from host
TASKS_STARTEPIN[1] 0x008 Captures the EPIN[1].PTR and EPIN[1].MAXCNT registers values, and enables endpoint IN 1 to
respond to traffic from host
TASKS_STARTEPIN[2] 0x00C Captures the EPIN[2].PTR and EPIN[2].MAXCNT registers values, and enables endpoint IN 2 to
respond to traffic from host
TASKS_STARTEPIN[3] 0x010 Captures the EPIN[3].PTR and EPIN[3].MAXCNT registers values, and enables endpoint IN 3 to
respond to traffic from host
TASKS_STARTEPIN[4] 0x014 Captures the EPIN[4].PTR and EPIN[4].MAXCNT registers values, and enables endpoint IN 4 to
respond to traffic from host

4413_417 v1.9 783

 Peripherals

Register Offset Description

TASKS_STARTEPIN[5] 0x018 Captures the EPIN[5].PTR and EPIN[5].MAXCNT registers values, and enables endpoint IN 5 to
respond to traffic from host
TASKS_STARTEPIN[6] 0x01C Captures the EPIN[6].PTR and EPIN[6].MAXCNT registers values, and enables endpoint IN 6 to
respond to traffic from host
TASKS_STARTEPIN[7] 0x020 Captures the EPIN[7].PTR and EPIN[7].MAXCNT registers values, and enables endpoint IN 7 to
respond to traffic from host
TASKS_STARTISOIN 0x024 Captures the ISOIN.PTR and ISOIN.MAXCNT registers values, and enables sending data on ISO
endpoint
TASKS_STARTEPOUT[0] 0x028 Captures the EPOUT[0].PTR and EPOUT[0].MAXCNT registers values, and enables endpoint 0 to
respond to traffic from host
TASKS_STARTEPOUT[1] 0x02C Captures the EPOUT[1].PTR and EPOUT[1].MAXCNT registers values, and enables endpoint 1 to
respond to traffic from host
TASKS_STARTEPOUT[2] 0x030 Captures the EPOUT[2].PTR and EPOUT[2].MAXCNT registers values, and enables endpoint 2 to
respond to traffic from host
TASKS_STARTEPOUT[3] 0x034 Captures the EPOUT[3].PTR and EPOUT[3].MAXCNT registers values, and enables endpoint 3 to
respond to traffic from host
TASKS_STARTEPOUT[4] 0x038 Captures the EPOUT[4].PTR and EPOUT[4].MAXCNT registers values, and enables endpoint 4 to
respond to traffic from host
TASKS_STARTEPOUT[5] 0x03C Captures the EPOUT[5].PTR and EPOUT[5].MAXCNT registers values, and enables endpoint 5 to
respond to traffic from host
TASKS_STARTEPOUT[6] 0x040 Captures the EPOUT[6].PTR and EPOUT[6].MAXCNT registers values, and enables endpoint 6 to
respond to traffic from host
TASKS_STARTEPOUT[7] 0x044 Captures the EPOUT[7].PTR and EPOUT[7].MAXCNT registers values, and enables endpoint 7 to
respond to traffic from host
TASKS_STARTISOOUT 0x048 Captures the ISOOUT.PTR and ISOOUT.MAXCNT registers values, and enables receiving of data on
ISO endpoint
TASKS_EP0RCVOUT 0x04C Allows OUT data stage on control endpoint 0
TASKS_EP0STATUS 0x050 Allows status stage on control endpoint 0
TASKS_EP0STALL 0x054 Stalls data and status stage on control endpoint 0
TASKS_DPDMDRIVE 0x058 Forces D+ and D- lines into the state defined in the DPDMVALUE register
TASKS_DPDMNODRIVE 0x05C Stops forcing D+ and D- lines into any state (USB engine takes control)
EVENTS_USBRESET 0x100 Signals that a USB reset condition has been detected on USB lines
EVENTS_STARTED 0x104 Confirms that the EPIN[n].PTR and EPIN[n].MAXCNT, or EPOUT[n].PTR and EPOUT[n].MAXCNT
registers have been captured on all endpoints reported in the EPSTATUS register
EVENTS_ENDEPIN[0] 0x108 The whole EPIN[0] buffer has been consumed. The buffer can be accessed safely by software.
EVENTS_ENDEPIN[1] 0x10C The whole EPIN[1] buffer has been consumed. The buffer can be accessed safely by software.
EVENTS_ENDEPIN[2] 0x110 The whole EPIN[2] buffer has been consumed. The buffer can be accessed safely by software.
EVENTS_ENDEPIN[3] 0x114 The whole EPIN[3] buffer has been consumed. The buffer can be accessed safely by software.
EVENTS_ENDEPIN[4] 0x118 The whole EPIN[4] buffer has been consumed. The buffer can be accessed safely by software.
EVENTS_ENDEPIN[5] 0x11C The whole EPIN[5] buffer has been consumed. The buffer can be accessed safely by software.
EVENTS_ENDEPIN[6] 0x120 The whole EPIN[6] buffer has been consumed. The buffer can be accessed safely by software.
EVENTS_ENDEPIN[7] 0x124 The whole EPIN[7] buffer has been consumed. The buffer can be accessed safely by software.
EVENTS_EP0DATADONE 0x128 An acknowledged data transfer has taken place on the control endpoint
EVENTS_ENDISOIN 0x12C The whole ISOIN buffer has been consumed. The buffer can be accessed safely by software.
EVENTS_ENDEPOUT[0] 0x130 The whole EPOUT[0] buffer has been consumed. The buffer can be accessed safely by software.
EVENTS_ENDEPOUT[1] 0x134 The whole EPOUT[1] buffer has been consumed. The buffer can be accessed safely by software.
EVENTS_ENDEPOUT[2] 0x138 The whole EPOUT[2] buffer has been consumed. The buffer can be accessed safely by software.
EVENTS_ENDEPOUT[3] 0x13C The whole EPOUT[3] buffer has been consumed. The buffer can be accessed safely by software.
EVENTS_ENDEPOUT[4] 0x140 The whole EPOUT[4] buffer has been consumed. The buffer can be accessed safely by software.
EVENTS_ENDEPOUT[5] 0x144 The whole EPOUT[5] buffer has been consumed. The buffer can be accessed safely by software.
EVENTS_ENDEPOUT[6] 0x148 The whole EPOUT[6] buffer has been consumed. The buffer can be accessed safely by software.
EVENTS_ENDEPOUT[7] 0x14C The whole EPOUT[7] buffer has been consumed. The buffer can be accessed safely by software.
EVENTS_ENDISOOUT 0x150 The whole ISOOUT buffer has been consumed. The buffer can be accessed safely by software.

4413_417 v1.9 784

 Peripherals

Register Offset Description

EVENTS_SOF 0x154 Signals that a SOF (start of frame) condition has been detected on USB lines
EVENTS_USBEVENT 0x158 An event or an error not covered by specific events has occurred. Check EVENTCAUSE register to find
the cause.
EVENTS_EP0SETUP 0x15C A valid SETUP token has been received (and acknowledged) on the control endpoint
EVENTS_EPDATA 0x160 A data transfer has occurred on a data endpoint, indicated by the EPDATASTATUS register
SHORTS 0x200 Shortcuts between local events and tasks
INTEN 0x300 Enable or disable interrupt
INTENSET 0x304 Enable interrupt
INTENCLR 0x308 Disable interrupt
EVENTCAUSE 0x400 Details on what caused the USBEVENT event
HALTED.EPIN[0] 0x420 IN endpoint halted status. Can be used as is as response to a GetStatus() request to endpoint.
HALTED.EPIN[1] 0x424 IN endpoint halted status. Can be used as is as response to a GetStatus() request to endpoint.
HALTED.EPIN[2] 0x428 IN endpoint halted status. Can be used as is as response to a GetStatus() request to endpoint.
HALTED.EPIN[3] 0x42C IN endpoint halted status. Can be used as is as response to a GetStatus() request to endpoint.
HALTED.EPIN[4] 0x430 IN endpoint halted status. Can be used as is as response to a GetStatus() request to endpoint.
HALTED.EPIN[5] 0x434 IN endpoint halted status. Can be used as is as response to a GetStatus() request to endpoint.
HALTED.EPIN[6] 0x438 IN endpoint halted status. Can be used as is as response to a GetStatus() request to endpoint.
HALTED.EPIN[7] 0x43C IN endpoint halted status. Can be used as is as response to a GetStatus() request to endpoint.
HALTED.EPOUT[0] 0x444 OUT endpoint halted status. Can be used as is as response to a GetStatus() request to endpoint.
HALTED.EPOUT[1] 0x448 OUT endpoint halted status. Can be used as is as response to a GetStatus() request to endpoint.
HALTED.EPOUT[2] 0x44C OUT endpoint halted status. Can be used as is as response to a GetStatus() request to endpoint.
HALTED.EPOUT[3] 0x450 OUT endpoint halted status. Can be used as is as response to a GetStatus() request to endpoint.
HALTED.EPOUT[4] 0x454 OUT endpoint halted status. Can be used as is as response to a GetStatus() request to endpoint.
HALTED.EPOUT[5] 0x458 OUT endpoint halted status. Can be used as is as response to a GetStatus() request to endpoint.
HALTED.EPOUT[6] 0x45C OUT endpoint halted status. Can be used as is as response to a GetStatus() request to endpoint.
HALTED.EPOUT[7] 0x460 OUT endpoint halted status. Can be used as is as response to a GetStatus() request to endpoint.
EPSTATUS 0x468 Provides information on which endpoint's EasyDMA registers have been captured
EPDATASTATUS 0x46C Provides information on which endpoint(s) an acknowledged data transfer has occurred (EPDATA
event)
USBADDR 0x470 Device USB address
BMREQUESTTYPE 0x480 SETUP data, byte 0, bmRequestType
BREQUEST 0x484 SETUP data, byte 1, bRequest
WVALUEL 0x488 SETUP data, byte 2, LSB of wValue
WVALUEH 0x48C SETUP data, byte 3, MSB of wValue
WINDEXL 0x490 SETUP data, byte 4, LSB of wIndex
WINDEXH 0x494 SETUP data, byte 5, MSB of wIndex
WLENGTHL 0x498 SETUP data, byte 6, LSB of wLength
WLENGTHH 0x49C SETUP data, byte 7, MSB of wLength
SIZE.EPOUT[0] 0x4A0 Number of bytes received last in the data stage of this OUT endpoint
SIZE.EPOUT[1] 0x4A4 Number of bytes received last in the data stage of this OUT endpoint
SIZE.EPOUT[2] 0x4A8 Number of bytes received last in the data stage of this OUT endpoint
SIZE.EPOUT[3] 0x4AC Number of bytes received last in the data stage of this OUT endpoint
SIZE.EPOUT[4] 0x4B0 Number of bytes received last in the data stage of this OUT endpoint
SIZE.EPOUT[5] 0x4B4 Number of bytes received last in the data stage of this OUT endpoint
SIZE.EPOUT[6] 0x4B8 Number of bytes received last in the data stage of this OUT endpoint
SIZE.EPOUT[7] 0x4BC Number of bytes received last in the data stage of this OUT endpoint
SIZE.ISOOUT 0x4C0 Number of bytes received last on this ISO OUT data endpoint
ENABLE 0x500 Enable USB
USBPULLUP 0x504 Control of the USB pull-up
DPDMVALUE 0x508 State D+ and D- lines will be forced into by the DPDMDRIVE task. The DPDMNODRIVE task reverts
the control of the lines to MAC IP (no forcing).
DTOGGLE 0x50C Data toggle control and status
EPINEN 0x510 Endpoint IN enable

4413_417 v1.9 785

 Peripherals

Register Offset Description

EPOUTEN 0x514 Endpoint OUT enable
EPSTALL 0x518 STALL endpoints
ISOSPLIT 0x51C Controls the split of ISO buffers
FRAMECNTR 0x520 Returns the current value of the start of frame counter
LOWPOWER 0x52C Controls USBD peripheral low power mode during USB suspend
ISOINCONFIG 0x530 Controls the response of the ISO IN endpoint to an IN token when no data is ready to be sent
EPIN[0].PTR 0x600 Data pointer
EPIN[0].MAXCNT 0x604 Maximum number of bytes to transfer
EPIN[0].AMOUNT 0x608 Number of bytes transferred in the last transaction
EPIN[1].PTR 0x614 Data pointer
EPIN[1].MAXCNT 0x618 Maximum number of bytes to transfer
EPIN[1].AMOUNT 0x61C Number of bytes transferred in the last transaction
EPIN[2].PTR 0x628 Data pointer
EPIN[2].MAXCNT 0x62C Maximum number of bytes to transfer
EPIN[2].AMOUNT 0x630 Number of bytes transferred in the last transaction
EPIN[3].PTR 0x63C Data pointer
EPIN[3].MAXCNT 0x640 Maximum number of bytes to transfer
EPIN[3].AMOUNT 0x644 Number of bytes transferred in the last transaction
EPIN[4].PTR 0x650 Data pointer
EPIN[4].MAXCNT 0x654 Maximum number of bytes to transfer
EPIN[4].AMOUNT 0x658 Number of bytes transferred in the last transaction
EPIN[5].PTR 0x664 Data pointer
EPIN[5].MAXCNT 0x668 Maximum number of bytes to transfer
EPIN[5].AMOUNT 0x66C Number of bytes transferred in the last transaction
EPIN[6].PTR 0x678 Data pointer
EPIN[6].MAXCNT 0x67C Maximum number of bytes to transfer
EPIN[6].AMOUNT 0x680 Number of bytes transferred in the last transaction
EPIN[7].PTR 0x68C Data pointer
EPIN[7].MAXCNT 0x690 Maximum number of bytes to transfer
EPIN[7].AMOUNT 0x694 Number of bytes transferred in the last transaction
ISOIN.PTR 0x6A0 Data pointer
ISOIN.MAXCNT 0x6A4 Maximum number of bytes to transfer
ISOIN.AMOUNT 0x6A8 Number of bytes transferred in the last transaction
EPOUT[0].PTR 0x700 Data pointer
EPOUT[0].MAXCNT 0x704 Maximum number of bytes to transfer
EPOUT[0].AMOUNT 0x708 Number of bytes transferred in the last transaction
EPOUT[1].PTR 0x714 Data pointer
EPOUT[1].MAXCNT 0x718 Maximum number of bytes to transfer
EPOUT[1].AMOUNT 0x71C Number of bytes transferred in the last transaction
EPOUT[2].PTR 0x728 Data pointer
EPOUT[2].MAXCNT 0x72C Maximum number of bytes to transfer
EPOUT[2].AMOUNT 0x730 Number of bytes transferred in the last transaction
EPOUT[3].PTR 0x73C Data pointer
EPOUT[3].MAXCNT 0x740 Maximum number of bytes to transfer
EPOUT[3].AMOUNT 0x744 Number of bytes transferred in the last transaction
EPOUT[4].PTR 0x750 Data pointer
EPOUT[4].MAXCNT 0x754 Maximum number of bytes to transfer
EPOUT[4].AMOUNT 0x758 Number of bytes transferred in the last transaction
EPOUT[5].PTR 0x764 Data pointer
EPOUT[5].MAXCNT 0x768 Maximum number of bytes to transfer
EPOUT[5].AMOUNT 0x76C Number of bytes transferred in the last transaction
EPOUT[6].PTR 0x778 Data pointer
EPOUT[6].MAXCNT 0x77C Maximum number of bytes to transfer

4413_417 v1.9 786

 Peripherals

Register Offset Description

EPOUT[6].AMOUNT 0x780 Number of bytes transferred in the last transaction
EPOUT[7].PTR 0x78C Data pointer
EPOUT[7].MAXCNT 0x790 Maximum number of bytes to transfer
EPOUT[7].AMOUNT 0x794 Number of bytes transferred in the last transaction
ISOOUT.PTR 0x7A0 Data pointer
ISOOUT.MAXCNT 0x7A4 Maximum number of bytes to transfer
ISOOUT.AMOUNT 0x7A8 Number of bytes transferred in the last transaction

6.35.13.1 TASKS_STARTEPIN[0]
Address offset: 0x004
Captures the EPIN[0].PTR and EPIN[0].MAXCNT registers values, and enables endpoint IN 0 to respond to
traffic from host

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STARTEPIN Captures the EPIN[0].PTR and EPIN[0].MAXCNT registers values, and enables
endpoint IN 0 to respond to traffic from host
Trigger 1 Trigger task

6.35.13.2 TASKS_STARTEPIN[1]
Address offset: 0x008
Captures the EPIN[1].PTR and EPIN[1].MAXCNT registers values, and enables endpoint IN 1 to respond to
traffic from host

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STARTEPIN Captures the EPIN[1].PTR and EPIN[1].MAXCNT registers values, and enables
endpoint IN 1 to respond to traffic from host
Trigger 1 Trigger task

6.35.13.3 TASKS_STARTEPIN[2]
Address offset: 0x00C
Captures the EPIN[2].PTR and EPIN[2].MAXCNT registers values, and enables endpoint IN 2 to respond to
traffic from host

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STARTEPIN Captures the EPIN[2].PTR and EPIN[2].MAXCNT registers values, and enables
endpoint IN 2 to respond to traffic from host
Trigger 1 Trigger task

4413_417 v1.9 787

 Peripherals

6.35.13.4 TASKS_STARTEPIN[3]
Address offset: 0x010
Captures the EPIN[3].PTR and EPIN[3].MAXCNT registers values, and enables endpoint IN 3 to respond to
traffic from host

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STARTEPIN Captures the EPIN[3].PTR and EPIN[3].MAXCNT registers values, and enables
endpoint IN 3 to respond to traffic from host
Trigger 1 Trigger task

6.35.13.5 TASKS_STARTEPIN[4]
Address offset: 0x014
Captures the EPIN[4].PTR and EPIN[4].MAXCNT registers values, and enables endpoint IN 4 to respond to
traffic from host

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STARTEPIN Captures the EPIN[4].PTR and EPIN[4].MAXCNT registers values, and enables
endpoint IN 4 to respond to traffic from host
Trigger 1 Trigger task

6.35.13.6 TASKS_STARTEPIN[5]
Address offset: 0x018
Captures the EPIN[5].PTR and EPIN[5].MAXCNT registers values, and enables endpoint IN 5 to respond to
traffic from host

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STARTEPIN Captures the EPIN[5].PTR and EPIN[5].MAXCNT registers values, and enables
endpoint IN 5 to respond to traffic from host
Trigger 1 Trigger task

6.35.13.7 TASKS_STARTEPIN[6]
Address offset: 0x01C
Captures the EPIN[6].PTR and EPIN[6].MAXCNT registers values, and enables endpoint IN 6 to respond to
traffic from host

4413_417 v1.9 788

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STARTEPIN Captures the EPIN[6].PTR and EPIN[6].MAXCNT registers values, and enables
endpoint IN 6 to respond to traffic from host
Trigger 1 Trigger task

6.35.13.8 TASKS_STARTEPIN[7]
Address offset: 0x020
Captures the EPIN[7].PTR and EPIN[7].MAXCNT registers values, and enables endpoint IN 7 to respond to
traffic from host

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STARTEPIN Captures the EPIN[7].PTR and EPIN[7].MAXCNT registers values, and enables
endpoint IN 7 to respond to traffic from host
Trigger 1 Trigger task

6.35.13.9 TASKS_STARTISOIN
Address offset: 0x024
Captures the ISOIN.PTR and ISOIN.MAXCNT registers values, and enables sending data on ISO endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STARTISOIN Captures the ISOIN.PTR and ISOIN.MAXCNT registers values, and enables
sending data on ISO endpoint
Trigger 1 Trigger task

6.35.13.10 TASKS_STARTEPOUT[0]
Address offset: 0x028
Captures the EPOUT[0].PTR and EPOUT[0].MAXCNT registers values, and enables endpoint 0 to respond to
traffic from host

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STARTEPOUT Captures the EPOUT[0].PTR and EPOUT[0].MAXCNT registers values, and
enables endpoint 0 to respond to traffic from host
Trigger 1 Trigger task

6.35.13.11 TASKS_STARTEPOUT[1]
Address offset: 0x02C

4413_417 v1.9 789

 Peripherals

Captures the EPOUT[1].PTR and EPOUT[1].MAXCNT registers values, and enables endpoint 1 to respond to
traffic from host

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STARTEPOUT Captures the EPOUT[1].PTR and EPOUT[1].MAXCNT registers values, and
enables endpoint 1 to respond to traffic from host
Trigger 1 Trigger task

6.35.13.12 TASKS_STARTEPOUT[2]
Address offset: 0x030
Captures the EPOUT[2].PTR and EPOUT[2].MAXCNT registers values, and enables endpoint 2 to respond to
traffic from host

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STARTEPOUT Captures the EPOUT[2].PTR and EPOUT[2].MAXCNT registers values, and
enables endpoint 2 to respond to traffic from host
Trigger 1 Trigger task

6.35.13.13 TASKS_STARTEPOUT[3]
Address offset: 0x034
Captures the EPOUT[3].PTR and EPOUT[3].MAXCNT registers values, and enables endpoint 3 to respond to
traffic from host

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STARTEPOUT Captures the EPOUT[3].PTR and EPOUT[3].MAXCNT registers values, and
enables endpoint 3 to respond to traffic from host
Trigger 1 Trigger task

6.35.13.14 TASKS_STARTEPOUT[4]
Address offset: 0x038
Captures the EPOUT[4].PTR and EPOUT[4].MAXCNT registers values, and enables endpoint 4 to respond to
traffic from host

4413_417 v1.9 790

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STARTEPOUT Captures the EPOUT[4].PTR and EPOUT[4].MAXCNT registers values, and
enables endpoint 4 to respond to traffic from host
Trigger 1 Trigger task

6.35.13.15 TASKS_STARTEPOUT[5]
Address offset: 0x03C
Captures the EPOUT[5].PTR and EPOUT[5].MAXCNT registers values, and enables endpoint 5 to respond to
traffic from host

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STARTEPOUT Captures the EPOUT[5].PTR and EPOUT[5].MAXCNT registers values, and
enables endpoint 5 to respond to traffic from host
Trigger 1 Trigger task

6.35.13.16 TASKS_STARTEPOUT[6]
Address offset: 0x040
Captures the EPOUT[6].PTR and EPOUT[6].MAXCNT registers values, and enables endpoint 6 to respond to
traffic from host

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STARTEPOUT Captures the EPOUT[6].PTR and EPOUT[6].MAXCNT registers values, and
enables endpoint 6 to respond to traffic from host
Trigger 1 Trigger task

6.35.13.17 TASKS_STARTEPOUT[7]
Address offset: 0x044
Captures the EPOUT[7].PTR and EPOUT[7].MAXCNT registers values, and enables endpoint 7 to respond to
traffic from host

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STARTEPOUT Captures the EPOUT[7].PTR and EPOUT[7].MAXCNT registers values, and
enables endpoint 7 to respond to traffic from host
Trigger 1 Trigger task

4413_417 v1.9 791

 Peripherals

6.35.13.18 TASKS_STARTISOOUT
Address offset: 0x048
Captures the ISOOUT.PTR and ISOOUT.MAXCNT registers values, and enables receiving of data on ISO
endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_STARTISOOUT Captures the ISOOUT.PTR and ISOOUT.MAXCNT registers values, and
enables receiving of data on ISO endpoint
Trigger 1 Trigger task

6.35.13.19 TASKS_EP0RCVOUT
Address offset: 0x04C
Allows OUT data stage on control endpoint 0

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_EP0RCVOUT Allows OUT data stage on control endpoint 0
Trigger 1 Trigger task

6.35.13.20 TASKS_EP0STATUS
Address offset: 0x050
Allows status stage on control endpoint 0

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_EP0STATUS Allows status stage on control endpoint 0
Trigger 1 Trigger task

6.35.13.21 TASKS_EP0STALL
Address offset: 0x054
Stalls data and status stage on control endpoint 0

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_EP0STALL Stalls data and status stage on control endpoint 0
Trigger 1 Trigger task

4413_417 v1.9 792

 Peripherals

6.35.13.22 TASKS_DPDMDRIVE
Address offset: 0x058
Forces D+ and D- lines into the state defined in the DPDMVALUE register

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_DPDMDRIVE Forces D+ and D- lines into the state defined in the DPDMVALUE register
Trigger 1 Trigger task

6.35.13.23 TASKS_DPDMNODRIVE
Address offset: 0x05C
Stops forcing D+ and D- lines into any state (USB engine takes control)

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_DPDMNODRIVE Stops forcing D+ and D- lines into any state (USB engine takes control)
Trigger 1 Trigger task

6.35.13.24 EVENTS_USBRESET
Address offset: 0x100
Signals that a USB reset condition has been detected on USB lines

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_USBRESET Signals that a USB reset condition has been detected on USB lines
NotGenerated 0 Event not generated
Generated 1 Event generated

6.35.13.25 EVENTS_STARTED
Address offset: 0x104
Confirms that the EPIN[n].PTR and EPIN[n].MAXCNT, or EPOUT[n].PTR and EPOUT[n].MAXCNT registers
have been captured on all endpoints reported in the EPSTATUS register

4413_417 v1.9 793

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_STARTED Confirms that the EPIN[n].PTR and EPIN[n].MAXCNT, or EPOUT[n].PTR and
EPOUT[n].MAXCNT registers have been captured on all endpoints reported
in the EPSTATUS register
NotGenerated 0 Event not generated
Generated 1 Event generated

6.35.13.26 EVENTS_ENDEPIN[0]
Address offset: 0x108
The whole EPIN[0] buffer has been consumed. The buffer can be accessed safely by software.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_ENDEPIN The whole EPIN[0] buffer has been consumed. The buffer can be accessed
safely by software.
NotGenerated 0 Event not generated
Generated 1 Event generated

6.35.13.27 EVENTS_ENDEPIN[1]
Address offset: 0x10C
The whole EPIN[1] buffer has been consumed. The buffer can be accessed safely by software.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_ENDEPIN The whole EPIN[1] buffer has been consumed. The buffer can be accessed
safely by software.
NotGenerated 0 Event not generated
Generated 1 Event generated

6.35.13.28 EVENTS_ENDEPIN[2]
Address offset: 0x110
The whole EPIN[2] buffer has been consumed. The buffer can be accessed safely by software.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_ENDEPIN The whole EPIN[2] buffer has been consumed. The buffer can be accessed
safely by software.
NotGenerated 0 Event not generated
Generated 1 Event generated

4413_417 v1.9 794

 Peripherals

6.35.13.29 EVENTS_ENDEPIN[3]
Address offset: 0x114
The whole EPIN[3] buffer has been consumed. The buffer can be accessed safely by software.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_ENDEPIN The whole EPIN[3] buffer has been consumed. The buffer can be accessed
safely by software.
NotGenerated 0 Event not generated
Generated 1 Event generated

6.35.13.30 EVENTS_ENDEPIN[4]
Address offset: 0x118
The whole EPIN[4] buffer has been consumed. The buffer can be accessed safely by software.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_ENDEPIN The whole EPIN[4] buffer has been consumed. The buffer can be accessed
safely by software.
NotGenerated 0 Event not generated
Generated 1 Event generated

6.35.13.31 EVENTS_ENDEPIN[5]
Address offset: 0x11C
The whole EPIN[5] buffer has been consumed. The buffer can be accessed safely by software.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_ENDEPIN The whole EPIN[5] buffer has been consumed. The buffer can be accessed
safely by software.
NotGenerated 0 Event not generated
Generated 1 Event generated

6.35.13.32 EVENTS_ENDEPIN[6]
Address offset: 0x120
The whole EPIN[6] buffer has been consumed. The buffer can be accessed safely by software.

4413_417 v1.9 795

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_ENDEPIN The whole EPIN[6] buffer has been consumed. The buffer can be accessed
safely by software.
NotGenerated 0 Event not generated
Generated 1 Event generated

6.35.13.33 EVENTS_ENDEPIN[7]
Address offset: 0x124
The whole EPIN[7] buffer has been consumed. The buffer can be accessed safely by software.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_ENDEPIN The whole EPIN[7] buffer has been consumed. The buffer can be accessed
safely by software.
NotGenerated 0 Event not generated
Generated 1 Event generated

6.35.13.34 EVENTS_EP0DATADONE
Address offset: 0x128
An acknowledged data transfer has taken place on the control endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_EP0DATADONE An acknowledged data transfer has taken place on the control endpoint
NotGenerated 0 Event not generated
Generated 1 Event generated

6.35.13.35 EVENTS_ENDISOIN
Address offset: 0x12C
The whole ISOIN buffer has been consumed. The buffer can be accessed safely by software.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_ENDISOIN The whole ISOIN buffer has been consumed. The buffer can be accessed
safely by software.
NotGenerated 0 Event not generated
Generated 1 Event generated

4413_417 v1.9 796

 Peripherals

6.35.13.36 EVENTS_ENDEPOUT[0]
Address offset: 0x130
The whole EPOUT[0] buffer has been consumed. The buffer can be accessed safely by software.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_ENDEPOUT The whole EPOUT[0] buffer has been consumed. The buffer can be accessed
safely by software.
NotGenerated 0 Event not generated
Generated 1 Event generated

6.35.13.37 EVENTS_ENDEPOUT[1]
Address offset: 0x134
The whole EPOUT[1] buffer has been consumed. The buffer can be accessed safely by software.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_ENDEPOUT The whole EPOUT[1] buffer has been consumed. The buffer can be accessed
safely by software.
NotGenerated 0 Event not generated
Generated 1 Event generated

6.35.13.38 EVENTS_ENDEPOUT[2]
Address offset: 0x138
The whole EPOUT[2] buffer has been consumed. The buffer can be accessed safely by software.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_ENDEPOUT The whole EPOUT[2] buffer has been consumed. The buffer can be accessed
safely by software.
NotGenerated 0 Event not generated
Generated 1 Event generated

6.35.13.39 EVENTS_ENDEPOUT[3]
Address offset: 0x13C
The whole EPOUT[3] buffer has been consumed. The buffer can be accessed safely by software.

4413_417 v1.9 797

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_ENDEPOUT The whole EPOUT[3] buffer has been consumed. The buffer can be accessed
safely by software.
NotGenerated 0 Event not generated
Generated 1 Event generated

6.35.13.40 EVENTS_ENDEPOUT[4]
Address offset: 0x140
The whole EPOUT[4] buffer has been consumed. The buffer can be accessed safely by software.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_ENDEPOUT The whole EPOUT[4] buffer has been consumed. The buffer can be accessed
safely by software.
NotGenerated 0 Event not generated
Generated 1 Event generated

6.35.13.41 EVENTS_ENDEPOUT[5]
Address offset: 0x144
The whole EPOUT[5] buffer has been consumed. The buffer can be accessed safely by software.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_ENDEPOUT The whole EPOUT[5] buffer has been consumed. The buffer can be accessed
safely by software.
NotGenerated 0 Event not generated
Generated 1 Event generated

6.35.13.42 EVENTS_ENDEPOUT[6]
Address offset: 0x148
The whole EPOUT[6] buffer has been consumed. The buffer can be accessed safely by software.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_ENDEPOUT The whole EPOUT[6] buffer has been consumed. The buffer can be accessed
safely by software.
NotGenerated 0 Event not generated
Generated 1 Event generated

4413_417 v1.9 798

 Peripherals

6.35.13.43 EVENTS_ENDEPOUT[7]
Address offset: 0x14C
The whole EPOUT[7] buffer has been consumed. The buffer can be accessed safely by software.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_ENDEPOUT The whole EPOUT[7] buffer has been consumed. The buffer can be accessed
safely by software.
NotGenerated 0 Event not generated
Generated 1 Event generated

6.35.13.44 EVENTS_ENDISOOUT
Address offset: 0x150
The whole ISOOUT buffer has been consumed. The buffer can be accessed safely by software.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_ENDISOOUT The whole ISOOUT buffer has been consumed. The buffer can be accessed
safely by software.
NotGenerated 0 Event not generated
Generated 1 Event generated

6.35.13.45 EVENTS_SOF
Address offset: 0x154
Signals that a SOF (start of frame) condition has been detected on USB lines

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_SOF Signals that a SOF (start of frame) condition has been detected on USB lines
NotGenerated 0 Event not generated
Generated 1 Event generated

6.35.13.46 EVENTS_USBEVENT
Address offset: 0x158
An event or an error not covered by specific events has occurred. Check EVENTCAUSE register to find the
cause.

4413_417 v1.9 799

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_USBEVENT An event or an error not covered by specific events has occurred. Check
EVENTCAUSE register to find the cause.
NotGenerated 0 Event not generated
Generated 1 Event generated

6.35.13.47 EVENTS_EP0SETUP
Address offset: 0x15C
A valid SETUP token has been received (and acknowledged) on the control endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_EP0SETUP A valid SETUP token has been received (and acknowledged) on the control
endpoint
NotGenerated 0 Event not generated
Generated 1 Event generated

6.35.13.48 EVENTS_EPDATA
Address offset: 0x160
A data transfer has occurred on a data endpoint, indicated by the EPDATASTATUS register

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_EPDATA A data transfer has occurred on a data endpoint, indicated by the
EPDATASTATUS register
NotGenerated 0 Event not generated
Generated 1 Event generated

6.35.13.49 SHORTS
Address offset: 0x200
Shortcuts between local events and tasks

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EP0DATADONE_STARTEPIN0 Shortcut between event EP0DATADONE and task STARTEPIN[0]
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
B RW EP0DATADONE_STARTEPOUT0 Shortcut between event EP0DATADONE and task STARTEPOUT[0]
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut

4413_417 v1.9 800

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
C RW EP0DATADONE_EP0STATUS Shortcut between event EP0DATADONE and task EP0STATUS
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
D RW ENDEPOUT0_EP0STATUS Shortcut between event ENDEPOUT[0] and task EP0STATUS
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut
E RW ENDEPOUT0_EP0RCVOUT Shortcut between event ENDEPOUT[0] and task EP0RCVOUT
Disabled 0 Disable shortcut
Enabled 1 Enable shortcut

6.35.13.50 INTEN
Address offset: 0x300
Enable or disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW USBRESET Enable or disable interrupt for event USBRESET
Disabled 0 Disable
Enabled 1 Enable
B RW STARTED Enable or disable interrupt for event STARTED
Disabled 0 Disable
Enabled 1 Enable
C RW ENDEPIN[0] Enable or disable interrupt for event ENDEPIN[0]
Disabled 0 Disable
Enabled 1 Enable
D RW ENDEPIN[1] Enable or disable interrupt for event ENDEPIN[1]
Disabled 0 Disable
Enabled 1 Enable
E RW ENDEPIN[2] Enable or disable interrupt for event ENDEPIN[2]
Disabled 0 Disable
Enabled 1 Enable
F RW ENDEPIN[3] Enable or disable interrupt for event ENDEPIN[3]
Disabled 0 Disable
Enabled 1 Enable
G RW ENDEPIN[4] Enable or disable interrupt for event ENDEPIN[4]
Disabled 0 Disable
Enabled 1 Enable
H RW ENDEPIN[5] Enable or disable interrupt for event ENDEPIN[5]
Disabled 0 Disable
Enabled 1 Enable
I RW ENDEPIN[6] Enable or disable interrupt for event ENDEPIN[6]
Disabled 0 Disable
Enabled 1 Enable
J RW ENDEPIN[7] Enable or disable interrupt for event ENDEPIN[7]
Disabled 0 Disable
Enabled 1 Enable

4413_417 v1.9 801

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
K RW EP0DATADONE Enable or disable interrupt for event EP0DATADONE
Disabled 0 Disable
Enabled 1 Enable
L RW ENDISOIN Enable or disable interrupt for event ENDISOIN
Disabled 0 Disable
Enabled 1 Enable
M RW ENDEPOUT[0] Enable or disable interrupt for event ENDEPOUT[0]
Disabled 0 Disable
Enabled 1 Enable
N RW ENDEPOUT[1] Enable or disable interrupt for event ENDEPOUT[1]
Disabled 0 Disable
Enabled 1 Enable
O RW ENDEPOUT[2] Enable or disable interrupt for event ENDEPOUT[2]
Disabled 0 Disable
Enabled 1 Enable
P RW ENDEPOUT[3] Enable or disable interrupt for event ENDEPOUT[3]
Disabled 0 Disable
Enabled 1 Enable
Q RW ENDEPOUT[4] Enable or disable interrupt for event ENDEPOUT[4]
Disabled 0 Disable
Enabled 1 Enable
R RW ENDEPOUT[5] Enable or disable interrupt for event ENDEPOUT[5]
Disabled 0 Disable
Enabled 1 Enable
S RW ENDEPOUT[6] Enable or disable interrupt for event ENDEPOUT[6]
Disabled 0 Disable
Enabled 1 Enable
T RW ENDEPOUT[7] Enable or disable interrupt for event ENDEPOUT[7]
Disabled 0 Disable
Enabled 1 Enable
U RW ENDISOOUT Enable or disable interrupt for event ENDISOOUT
Disabled 0 Disable
Enabled 1 Enable
V RW SOF Enable or disable interrupt for event SOF
Disabled 0 Disable
Enabled 1 Enable
W RW USBEVENT Enable or disable interrupt for event USBEVENT
Disabled 0 Disable
Enabled 1 Enable
X RW EP0SETUP Enable or disable interrupt for event EP0SETUP
Disabled 0 Disable
Enabled 1 Enable
Y RW EPDATA Enable or disable interrupt for event EPDATA
Disabled 0 Disable
Enabled 1 Enable

6.35.13.51 INTENSET
Address offset: 0x304
Enable interrupt

4413_417 v1.9 802

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW USBRESET Write '1' to enable interrupt for event USBRESET
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW STARTED Write '1' to enable interrupt for event STARTED
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW ENDEPIN[0] Write '1' to enable interrupt for event ENDEPIN[0]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
D RW ENDEPIN[1] Write '1' to enable interrupt for event ENDEPIN[1]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
E RW ENDEPIN[2] Write '1' to enable interrupt for event ENDEPIN[2]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
F RW ENDEPIN[3] Write '1' to enable interrupt for event ENDEPIN[3]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
G RW ENDEPIN[4] Write '1' to enable interrupt for event ENDEPIN[4]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
H RW ENDEPIN[5] Write '1' to enable interrupt for event ENDEPIN[5]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
I RW ENDEPIN[6] Write '1' to enable interrupt for event ENDEPIN[6]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
J RW ENDEPIN[7] Write '1' to enable interrupt for event ENDEPIN[7]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
K RW EP0DATADONE Write '1' to enable interrupt for event EP0DATADONE
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
L RW ENDISOIN Write '1' to enable interrupt for event ENDISOIN
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
M RW ENDEPOUT[0] Write '1' to enable interrupt for event ENDEPOUT[0]
Set 1 Enable

4413_417 v1.9 803

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
N RW ENDEPOUT[1] Write '1' to enable interrupt for event ENDEPOUT[1]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
O RW ENDEPOUT[2] Write '1' to enable interrupt for event ENDEPOUT[2]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
P RW ENDEPOUT[3] Write '1' to enable interrupt for event ENDEPOUT[3]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
Q RW ENDEPOUT[4] Write '1' to enable interrupt for event ENDEPOUT[4]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
R RW ENDEPOUT[5] Write '1' to enable interrupt for event ENDEPOUT[5]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
S RW ENDEPOUT[6] Write '1' to enable interrupt for event ENDEPOUT[6]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
T RW ENDEPOUT[7] Write '1' to enable interrupt for event ENDEPOUT[7]
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
U RW ENDISOOUT Write '1' to enable interrupt for event ENDISOOUT
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
V RW SOF Write '1' to enable interrupt for event SOF
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
W RW USBEVENT Write '1' to enable interrupt for event USBEVENT
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
X RW EP0SETUP Write '1' to enable interrupt for event EP0SETUP
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
Y RW EPDATA Write '1' to enable interrupt for event EPDATA
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

4413_417 v1.9 804

 Peripherals

6.35.13.52 INTENCLR
Address offset: 0x308
Disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW USBRESET Write '1' to disable interrupt for event USBRESET
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
B RW STARTED Write '1' to disable interrupt for event STARTED
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
C RW ENDEPIN[0] Write '1' to disable interrupt for event ENDEPIN[0]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
D RW ENDEPIN[1] Write '1' to disable interrupt for event ENDEPIN[1]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
E RW ENDEPIN[2] Write '1' to disable interrupt for event ENDEPIN[2]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
F RW ENDEPIN[3] Write '1' to disable interrupt for event ENDEPIN[3]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
G RW ENDEPIN[4] Write '1' to disable interrupt for event ENDEPIN[4]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
H RW ENDEPIN[5] Write '1' to disable interrupt for event ENDEPIN[5]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
I RW ENDEPIN[6] Write '1' to disable interrupt for event ENDEPIN[6]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
J RW ENDEPIN[7] Write '1' to disable interrupt for event ENDEPIN[7]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
K RW EP0DATADONE Write '1' to disable interrupt for event EP0DATADONE
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

4413_417 v1.9 805

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
L RW ENDISOIN Write '1' to disable interrupt for event ENDISOIN
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
M RW ENDEPOUT[0] Write '1' to disable interrupt for event ENDEPOUT[0]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
N RW ENDEPOUT[1] Write '1' to disable interrupt for event ENDEPOUT[1]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
O RW ENDEPOUT[2] Write '1' to disable interrupt for event ENDEPOUT[2]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
P RW ENDEPOUT[3] Write '1' to disable interrupt for event ENDEPOUT[3]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
Q RW ENDEPOUT[4] Write '1' to disable interrupt for event ENDEPOUT[4]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
R RW ENDEPOUT[5] Write '1' to disable interrupt for event ENDEPOUT[5]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
S RW ENDEPOUT[6] Write '1' to disable interrupt for event ENDEPOUT[6]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
T RW ENDEPOUT[7] Write '1' to disable interrupt for event ENDEPOUT[7]
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
U RW ENDISOOUT Write '1' to disable interrupt for event ENDISOOUT
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
V RW SOF Write '1' to disable interrupt for event SOF
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
W RW USBEVENT Write '1' to disable interrupt for event USBEVENT
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
X RW EP0SETUP Write '1' to disable interrupt for event EP0SETUP
Clear 1 Disable

4413_417 v1.9 806

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID Y X W V U T S R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled
Y RW EPDATA Write '1' to disable interrupt for event EPDATA
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.35.13.53 EVENTCAUSE
Address offset: 0x400
Details on what caused the USBEVENT event

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW ISOOUTCRC CRC error was detected on isochronous OUT endpoint 8. Write '1' to clear.
W1C
NotDetected 0 No error detected
Detected 1 Error detected
B RW SUSPEND Signals that USB lines have been idle long enough for the device to enter
W1C suspend. Write '1' to clear.
NotDetected 0 Suspend not detected
Detected 1 Suspend detected
C RW RESUME Signals that a RESUME condition (K state or activity restart) has been
W1C detected on USB lines. Write '1' to clear.
NotDetected 0 Resume not detected
Detected 1 Resume detected
D RW USBWUALLOWED USB MAC has been woken up and operational. Write '1' to clear.
W1C
NotAllowed 0 Wake up not allowed
Allowed 1 Wake up allowed
E RW READY USB device is ready for normal operation. Write '1' to clear.
W1C
NotDetected 0 USBEVENT was not issued due to USBD peripheral ready
Ready 1 USBD peripheral is ready

6.35.13.54 HALTED.EPIN[0]
Address offset: 0x420
IN endpoint halted status. Can be used as is as response to a GetStatus() request to endpoint.

4413_417 v1.9 807

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R GETSTATUS IN endpoint halted status. Can be used as is as response to a GetStatus()
request to endpoint.
NotHalted 0 Endpoint is not halted
Halted 1 Endpoint is halted

6.35.13.55 HALTED.EPIN[1]
Address offset: 0x424
IN endpoint halted status. Can be used as is as response to a GetStatus() request to endpoint.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R GETSTATUS IN endpoint halted status. Can be used as is as response to a GetStatus()
request to endpoint.
NotHalted 0 Endpoint is not halted
Halted 1 Endpoint is halted

6.35.13.56 HALTED.EPIN[2]
Address offset: 0x428
IN endpoint halted status. Can be used as is as response to a GetStatus() request to endpoint.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R GETSTATUS IN endpoint halted status. Can be used as is as response to a GetStatus()
request to endpoint.
NotHalted 0 Endpoint is not halted
Halted 1 Endpoint is halted

6.35.13.57 HALTED.EPIN[3]
Address offset: 0x42C
IN endpoint halted status. Can be used as is as response to a GetStatus() request to endpoint.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R GETSTATUS IN endpoint halted status. Can be used as is as response to a GetStatus()
request to endpoint.
NotHalted 0 Endpoint is not halted
Halted 1 Endpoint is halted

4413_417 v1.9 808

 Peripherals

6.35.13.58 HALTED.EPIN[4]
Address offset: 0x430
IN endpoint halted status. Can be used as is as response to a GetStatus() request to endpoint.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R GETSTATUS IN endpoint halted status. Can be used as is as response to a GetStatus()
request to endpoint.
NotHalted 0 Endpoint is not halted
Halted 1 Endpoint is halted

6.35.13.59 HALTED.EPIN[5]
Address offset: 0x434
IN endpoint halted status. Can be used as is as response to a GetStatus() request to endpoint.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R GETSTATUS IN endpoint halted status. Can be used as is as response to a GetStatus()
request to endpoint.
NotHalted 0 Endpoint is not halted
Halted 1 Endpoint is halted

6.35.13.60 HALTED.EPIN[6]
Address offset: 0x438
IN endpoint halted status. Can be used as is as response to a GetStatus() request to endpoint.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R GETSTATUS IN endpoint halted status. Can be used as is as response to a GetStatus()
request to endpoint.
NotHalted 0 Endpoint is not halted
Halted 1 Endpoint is halted

6.35.13.61 HALTED.EPIN[7]
Address offset: 0x43C
IN endpoint halted status. Can be used as is as response to a GetStatus() request to endpoint.

4413_417 v1.9 809

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R GETSTATUS IN endpoint halted status. Can be used as is as response to a GetStatus()
request to endpoint.
NotHalted 0 Endpoint is not halted
Halted 1 Endpoint is halted

6.35.13.62 HALTED.EPOUT[0]
Address offset: 0x444
OUT endpoint halted status. Can be used as is as response to a GetStatus() request to endpoint.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R GETSTATUS OUT endpoint halted status. Can be used as is as response to a GetStatus()
request to endpoint.
NotHalted 0 Endpoint is not halted
Halted 1 Endpoint is halted

6.35.13.63 HALTED.EPOUT[1]
Address offset: 0x448
OUT endpoint halted status. Can be used as is as response to a GetStatus() request to endpoint.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R GETSTATUS OUT endpoint halted status. Can be used as is as response to a GetStatus()
request to endpoint.
NotHalted 0 Endpoint is not halted
Halted 1 Endpoint is halted

6.35.13.64 HALTED.EPOUT[2]
Address offset: 0x44C
OUT endpoint halted status. Can be used as is as response to a GetStatus() request to endpoint.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R GETSTATUS OUT endpoint halted status. Can be used as is as response to a GetStatus()
request to endpoint.
NotHalted 0 Endpoint is not halted
Halted 1 Endpoint is halted

4413_417 v1.9 810

 Peripherals

6.35.13.65 HALTED.EPOUT[3]
Address offset: 0x450
OUT endpoint halted status. Can be used as is as response to a GetStatus() request to endpoint.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R GETSTATUS OUT endpoint halted status. Can be used as is as response to a GetStatus()
request to endpoint.
NotHalted 0 Endpoint is not halted
Halted 1 Endpoint is halted

6.35.13.66 HALTED.EPOUT[4]
Address offset: 0x454
OUT endpoint halted status. Can be used as is as response to a GetStatus() request to endpoint.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R GETSTATUS OUT endpoint halted status. Can be used as is as response to a GetStatus()
request to endpoint.
NotHalted 0 Endpoint is not halted
Halted 1 Endpoint is halted

6.35.13.67 HALTED.EPOUT[5]
Address offset: 0x458
OUT endpoint halted status. Can be used as is as response to a GetStatus() request to endpoint.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R GETSTATUS OUT endpoint halted status. Can be used as is as response to a GetStatus()
request to endpoint.
NotHalted 0 Endpoint is not halted
Halted 1 Endpoint is halted

6.35.13.68 HALTED.EPOUT[6]
Address offset: 0x45C
OUT endpoint halted status. Can be used as is as response to a GetStatus() request to endpoint.

4413_417 v1.9 811

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R GETSTATUS OUT endpoint halted status. Can be used as is as response to a GetStatus()
request to endpoint.
NotHalted 0 Endpoint is not halted
Halted 1 Endpoint is halted

6.35.13.69 HALTED.EPOUT[7]
Address offset: 0x460
OUT endpoint halted status. Can be used as is as response to a GetStatus() request to endpoint.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R GETSTATUS OUT endpoint halted status. Can be used as is as response to a GetStatus()
request to endpoint.
NotHalted 0 Endpoint is not halted
Halted 1 Endpoint is halted

6.35.13.70 EPSTATUS
Address offset: 0x468
Provides information on which endpoint's EasyDMA registers have been captured

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EPIN0 Captured state of endpoint's EasyDMA registers. Write '1' to clear.
W1C
NoData 0 EasyDMA registers have not been captured for this endpoint
DataDone 1 EasyDMA registers have been captured for this endpoint
B RW EPIN1 Captured state of endpoint's EasyDMA registers. Write '1' to clear.
W1C
NoData 0 EasyDMA registers have not been captured for this endpoint
DataDone 1 EasyDMA registers have been captured for this endpoint
C RW EPIN2 Captured state of endpoint's EasyDMA registers. Write '1' to clear.
W1C
NoData 0 EasyDMA registers have not been captured for this endpoint
DataDone 1 EasyDMA registers have been captured for this endpoint
D RW EPIN3 Captured state of endpoint's EasyDMA registers. Write '1' to clear.
W1C
NoData 0 EasyDMA registers have not been captured for this endpoint
DataDone 1 EasyDMA registers have been captured for this endpoint
E RW EPIN4 Captured state of endpoint's EasyDMA registers. Write '1' to clear.
W1C
NoData 0 EasyDMA registers have not been captured for this endpoint
DataDone 1 EasyDMA registers have been captured for this endpoint

4413_417 v1.9 812

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
F RW EPIN5 Captured state of endpoint's EasyDMA registers. Write '1' to clear.
W1C
NoData 0 EasyDMA registers have not been captured for this endpoint
DataDone 1 EasyDMA registers have been captured for this endpoint
G RW EPIN6 Captured state of endpoint's EasyDMA registers. Write '1' to clear.
W1C
NoData 0 EasyDMA registers have not been captured for this endpoint
DataDone 1 EasyDMA registers have been captured for this endpoint
H RW EPIN7 Captured state of endpoint's EasyDMA registers. Write '1' to clear.
W1C
NoData 0 EasyDMA registers have not been captured for this endpoint
DataDone 1 EasyDMA registers have been captured for this endpoint
I RW EPIN8 Captured state of endpoint's EasyDMA registers. Write '1' to clear.
W1C
NoData 0 EasyDMA registers have not been captured for this endpoint
DataDone 1 EasyDMA registers have been captured for this endpoint
J RW EPOUT0 Captured state of endpoint's EasyDMA registers. Write '1' to clear.
W1C
NoData 0 EasyDMA registers have not been captured for this endpoint
DataDone 1 EasyDMA registers have been captured for this endpoint
K RW EPOUT1 Captured state of endpoint's EasyDMA registers. Write '1' to clear.
W1C
NoData 0 EasyDMA registers have not been captured for this endpoint
DataDone 1 EasyDMA registers have been captured for this endpoint
L RW EPOUT2 Captured state of endpoint's EasyDMA registers. Write '1' to clear.
W1C
NoData 0 EasyDMA registers have not been captured for this endpoint
DataDone 1 EasyDMA registers have been captured for this endpoint
M RW EPOUT3 Captured state of endpoint's EasyDMA registers. Write '1' to clear.
W1C
NoData 0 EasyDMA registers have not been captured for this endpoint
DataDone 1 EasyDMA registers have been captured for this endpoint
N RW EPOUT4 Captured state of endpoint's EasyDMA registers. Write '1' to clear.
W1C
NoData 0 EasyDMA registers have not been captured for this endpoint
DataDone 1 EasyDMA registers have been captured for this endpoint
O RW EPOUT5 Captured state of endpoint's EasyDMA registers. Write '1' to clear.
W1C
NoData 0 EasyDMA registers have not been captured for this endpoint
DataDone 1 EasyDMA registers have been captured for this endpoint
P RW EPOUT6 Captured state of endpoint's EasyDMA registers. Write '1' to clear.
W1C
NoData 0 EasyDMA registers have not been captured for this endpoint
DataDone 1 EasyDMA registers have been captured for this endpoint
Q RW EPOUT7 Captured state of endpoint's EasyDMA registers. Write '1' to clear.
W1C
NoData 0 EasyDMA registers have not been captured for this endpoint
DataDone 1 EasyDMA registers have been captured for this endpoint
R RW EPOUT8 Captured state of endpoint's EasyDMA registers. Write '1' to clear.
W1C

4413_417 v1.9 813

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID R Q P O N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
NoData 0 EasyDMA registers have not been captured for this endpoint
DataDone 1 EasyDMA registers have been captured for this endpoint

6.35.13.71 EPDATASTATUS
Address offset: 0x46C
Provides information on which endpoint(s) an acknowledged data transfer has occurred (EPDATA event)

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EPIN1 Acknowledged data transfer on this IN endpoint. Write '1' to clear.
W1C
NotDone 0 No acknowledged data transfer on this endpoint
DataDone 1 Acknowledged data transfer on this endpoint has occurred
B RW EPIN2 Acknowledged data transfer on this IN endpoint. Write '1' to clear.
W1C
NotDone 0 No acknowledged data transfer on this endpoint
DataDone 1 Acknowledged data transfer on this endpoint has occurred
C RW EPIN3 Acknowledged data transfer on this IN endpoint. Write '1' to clear.
W1C
NotDone 0 No acknowledged data transfer on this endpoint
DataDone 1 Acknowledged data transfer on this endpoint has occurred
D RW EPIN4 Acknowledged data transfer on this IN endpoint. Write '1' to clear.
W1C
NotDone 0 No acknowledged data transfer on this endpoint
DataDone 1 Acknowledged data transfer on this endpoint has occurred
E RW EPIN5 Acknowledged data transfer on this IN endpoint. Write '1' to clear.
W1C
NotDone 0 No acknowledged data transfer on this endpoint
DataDone 1 Acknowledged data transfer on this endpoint has occurred
F RW EPIN6 Acknowledged data transfer on this IN endpoint. Write '1' to clear.
W1C
NotDone 0 No acknowledged data transfer on this endpoint
DataDone 1 Acknowledged data transfer on this endpoint has occurred
G RW EPIN7 Acknowledged data transfer on this IN endpoint. Write '1' to clear.
W1C
NotDone 0 No acknowledged data transfer on this endpoint
DataDone 1 Acknowledged data transfer on this endpoint has occurred
H RW EPOUT1 Acknowledged data transfer on this OUT endpoint. Write '1' to clear.
W1C
NotStarted 0 No acknowledged data transfer on this endpoint
Started 1 Acknowledged data transfer on this endpoint has occurred
I RW EPOUT2 Acknowledged data transfer on this OUT endpoint. Write '1' to clear.
W1C
NotStarted 0 No acknowledged data transfer on this endpoint
Started 1 Acknowledged data transfer on this endpoint has occurred

4413_417 v1.9 814

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID N M L K J I H G F E D C B A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
J RW EPOUT3 Acknowledged data transfer on this OUT endpoint. Write '1' to clear.
W1C
NotStarted 0 No acknowledged data transfer on this endpoint
Started 1 Acknowledged data transfer on this endpoint has occurred
K RW EPOUT4 Acknowledged data transfer on this OUT endpoint. Write '1' to clear.
W1C
NotStarted 0 No acknowledged data transfer on this endpoint
Started 1 Acknowledged data transfer on this endpoint has occurred
L RW EPOUT5 Acknowledged data transfer on this OUT endpoint. Write '1' to clear.
W1C
NotStarted 0 No acknowledged data transfer on this endpoint
Started 1 Acknowledged data transfer on this endpoint has occurred
M RW EPOUT6 Acknowledged data transfer on this OUT endpoint. Write '1' to clear.
W1C
NotStarted 0 No acknowledged data transfer on this endpoint
Started 1 Acknowledged data transfer on this endpoint has occurred
N RW EPOUT7 Acknowledged data transfer on this OUT endpoint. Write '1' to clear.
W1C
NotStarted 0 No acknowledged data transfer on this endpoint
Started 1 Acknowledged data transfer on this endpoint has occurred

6.35.13.72 USBADDR
Address offset: 0x470
Device USB address

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R ADDR Device USB address

6.35.13.73 BMREQUESTTYPE
Address offset: 0x480
SETUP data, byte 0, bmRequestType

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B B A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R RECIPIENT Data transfer type
Device 0 Device
Interface 1 Interface
Endpoint 2 Endpoint
Other 3 Other
B R TYPE Data transfer type
Standard 0 Standard
Class 1 Class

4413_417 v1.9 815

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B B A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
Vendor 2 Vendor
C R DIRECTION Data transfer direction
HostToDevice 0 Host-to-device
DeviceToHost 1 Device-to-host

6.35.13.74 BREQUEST
Address offset: 0x484
SETUP data, byte 1, bRequest

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R BREQUEST SETUP data, byte 1, bRequest. Values provided for standard requests only,
user must implement class and vendor values.
STD_GET_STATUS 0 Standard request GET_STATUS
STD_CLEAR_FEATURE1 Standard request CLEAR_FEATURE
STD_SET_FEATURE 3 Standard request SET_FEATURE
STD_SET_ADDRESS 5 Standard request SET_ADDRESS
STD_GET_DESCRIPTOR
6 Standard request GET_DESCRIPTOR
STD_SET_DESCRIPTOR7 Standard request SET_DESCRIPTOR
STD_GET_CONFIGURATION
8 Standard request GET_CONFIGURATION
STD_SET_CONFIGURATION
9 Standard request SET_CONFIGURATION
STD_GET_INTERFACE 10 Standard request GET_INTERFACE
STD_SET_INTERFACE 11 Standard request SET_INTERFACE
STD_SYNCH_FRAME 12 Standard request SYNCH_FRAME

6.35.13.75 WVALUEL
Address offset: 0x488
SETUP data, byte 2, LSB of wValue

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R WVALUEL SETUP data, byte 2, LSB of wValue

6.35.13.76 WVALUEH
Address offset: 0x48C
SETUP data, byte 3, MSB of wValue

4413_417 v1.9 816

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R WVALUEH SETUP data, byte 3, MSB of wValue

6.35.13.77 WINDEXL
Address offset: 0x490
SETUP data, byte 4, LSB of wIndex

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R WINDEXL SETUP data, byte 4, LSB of wIndex

6.35.13.78 WINDEXH
Address offset: 0x494
SETUP data, byte 5, MSB of wIndex

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R WINDEXH SETUP data, byte 5, MSB of wIndex

6.35.13.79 WLENGTHL
Address offset: 0x498
SETUP data, byte 6, LSB of wLength

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R WLENGTHL SETUP data, byte 6, LSB of wLength

6.35.13.80 WLENGTHH
Address offset: 0x49C
SETUP data, byte 7, MSB of wLength

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R WLENGTHH SETUP data, byte 7, MSB of wLength

4413_417 v1.9 817

 Peripherals

6.35.13.81 SIZE.EPOUT[0]
Address offset: 0x4A0
Number of bytes received last in the data stage of this OUT endpoint
Write to any value to accept further OUT traffic on this endpoint, and overwrite the intermediate buffer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW SIZE Number of bytes received last in the data stage of this OUT endpoint
W0C

6.35.13.82 SIZE.EPOUT[1]
Address offset: 0x4A4
Number of bytes received last in the data stage of this OUT endpoint
Write to any value to accept further OUT traffic on this endpoint, and overwrite the intermediate buffer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW SIZE Number of bytes received last in the data stage of this OUT endpoint
W0C

6.35.13.83 SIZE.EPOUT[2]
Address offset: 0x4A8
Number of bytes received last in the data stage of this OUT endpoint
Write to any value to accept further OUT traffic on this endpoint, and overwrite the intermediate buffer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW SIZE Number of bytes received last in the data stage of this OUT endpoint
W0C

6.35.13.84 SIZE.EPOUT[3]
Address offset: 0x4AC
Number of bytes received last in the data stage of this OUT endpoint
Write to any value to accept further OUT traffic on this endpoint, and overwrite the intermediate buffer

4413_417 v1.9 818

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW SIZE Number of bytes received last in the data stage of this OUT endpoint
W0C

6.35.13.85 SIZE.EPOUT[4]
Address offset: 0x4B0
Number of bytes received last in the data stage of this OUT endpoint
Write to any value to accept further OUT traffic on this endpoint, and overwrite the intermediate buffer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW SIZE Number of bytes received last in the data stage of this OUT endpoint
W0C

6.35.13.86 SIZE.EPOUT[5]
Address offset: 0x4B4
Number of bytes received last in the data stage of this OUT endpoint
Write to any value to accept further OUT traffic on this endpoint, and overwrite the intermediate buffer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW SIZE Number of bytes received last in the data stage of this OUT endpoint
W0C

6.35.13.87 SIZE.EPOUT[6]
Address offset: 0x4B8
Number of bytes received last in the data stage of this OUT endpoint
Write to any value to accept further OUT traffic on this endpoint, and overwrite the intermediate buffer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW SIZE Number of bytes received last in the data stage of this OUT endpoint
W0C

6.35.13.88 SIZE.EPOUT[7]
Address offset: 0x4BC
Number of bytes received last in the data stage of this OUT endpoint

4413_417 v1.9 819

 Peripherals

Write to any value to accept further OUT traffic on this endpoint, and overwrite the intermediate buffer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A
Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW SIZE Number of bytes received last in the data stage of this OUT endpoint
W0C

6.35.13.89 SIZE.ISOOUT
Address offset: 0x4C0
Number of bytes received last on this ISO OUT data endpoint

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B A A A A A A A A A A

Reset 0x00010000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R SIZE Number of bytes received last on this ISO OUT data endpoint
B R ZERO Zero-length data packet received
Normal 0 No zero-length data received, use value in SIZE
ZeroData 1 Zero-length data received, ignore value in SIZE

6.35.13.90 ENABLE
Address offset: 0x500
Enable USB
After writing Disabled to this register, reading the register will return Enabled until USBD is completely
disabled.

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A- RW ENABLE Enable USB
Disabled 0 USB peripheral is disabled
Enabled 1 USB peripheral is enabled

6.35.13.91 USBPULLUP
Address offset: 0x504
Control of the USB pull-up

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW CONNECT Control of the USB pull-up on the D+ line
Disabled 0 Pull-up is disconnected
Enabled 1 Pull-up is connected to D+

4413_417 v1.9 820

 Peripherals

6.35.13.92 DPDMVALUE
Address offset: 0x508
State D+ and D- lines will be forced into by the DPDMDRIVE task. The DPDMNODRIVE task reverts the
control of the lines to MAC IP (no forcing).

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW STATE State D+ and D- lines will be forced into by the DPDMDRIVE task
Resume 1 D+ forced low, D- forced high (K state) for a timing preset in hardware (50 μs
or 5 ms, depending on bus state)
J 2 D+ forced high, D- forced low (J state)
K 4 D+ forced low, D- forced high (K state)

6.35.13.93 DTOGGLE
Address offset: 0x50C
Data toggle control and status
First write this register with VALUE=Nop to select the endpoint, then either read it to get the status from
VALUE, or write it again with VALUE=Data0 or Data1

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C C B A A A

Reset 0x00000100 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EP Select bulk endpoint number
B RW IO Selects IN or OUT endpoint
Out 0 Selects OUT endpoint
In 1 Selects IN endpoint
C RW VALUE Data toggle value
Nop 0 No action on data toggle when writing the register with this value
Data0 1 Data toggle is DATA0 on endpoint set by EP and IO
Data1 2 Data toggle is DATA1 on endpoint set by EP and IO

6.35.13.94 EPINEN
Address offset: 0x510
Endpoint IN enable

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID I H G F E D C B A

Reset 0x00000001 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
ID R/W Field Value ID Value Description
A RW IN0 Enable IN endpoint 0
Disable 0 Disable endpoint IN 0 (no response to IN tokens)
Enable 1 Enable endpoint IN 0 (response to IN tokens)
B RW IN1 Enable IN endpoint 1
Disable 0 Disable endpoint IN 1 (no response to IN tokens)
Enable 1 Enable endpoint IN 1 (response to IN tokens)

4413_417 v1.9 821

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID I H G F E D C B A

Reset 0x00000001 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
ID R/W Field Value ID Value Description
C RW IN2 Enable IN endpoint 2
Disable 0 Disable endpoint IN 2 (no response to IN tokens)
Enable 1 Enable endpoint IN 2 (response to IN tokens)
D RW IN3 Enable IN endpoint 3
Disable 0 Disable endpoint IN 3 (no response to IN tokens)
Enable 1 Enable endpoint IN 3 (response to IN tokens)
E RW IN4 Enable IN endpoint 4
Disable 0 Disable endpoint IN 4 (no response to IN tokens)
Enable 1 Enable endpoint IN 4 (response to IN tokens)
F RW IN5 Enable IN endpoint 5
Disable 0 Disable endpoint IN 5 (no response to IN tokens)
Enable 1 Enable endpoint IN 5 (response to IN tokens)
G RW IN6 Enable IN endpoint 6
Disable 0 Disable endpoint IN 6 (no response to IN tokens)
Enable 1 Enable endpoint IN 6 (response to IN tokens)
H RW IN7 Enable IN endpoint 7
Disable 0 Disable endpoint IN 7 (no response to IN tokens)
Enable 1 Enable endpoint IN 7 (response to IN tokens)
I RW ISOIN Enable ISO IN endpoint
Disable 0 Disable ISO IN endpoint 8
Enable 1 Enable ISO IN endpoint 8

6.35.13.95 EPOUTEN
Address offset: 0x514
Endpoint OUT enable

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID I H G F E D C B A

Reset 0x00000001 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
ID R/W Field Value ID Value Description
A RW OUT0 Enable OUT endpoint 0
Disable 0 Disable endpoint OUT 0 (no response to OUT tokens)
Enable 1 Enable endpoint OUT 0 (response to OUT tokens)
B RW OUT1 Enable OUT endpoint 1
Disable 0 Disable endpoint OUT 1 (no response to OUT tokens)
Enable 1 Enable endpoint OUT 1 (response to OUT tokens)
C RW OUT2 Enable OUT endpoint 2
Disable 0 Disable endpoint OUT 2 (no response to OUT tokens)
Enable 1 Enable endpoint OUT 2 (response to OUT tokens)
D RW OUT3 Enable OUT endpoint 3
Disable 0 Disable endpoint OUT 3 (no response to OUT tokens)
Enable 1 Enable endpoint OUT 3 (response to OUT tokens)
E RW OUT4 Enable OUT endpoint 4
Disable 0 Disable endpoint OUT 4 (no response to OUT tokens)
Enable 1 Enable endpoint OUT 4 (response to OUT tokens)
F RW OUT5 Enable OUT endpoint 5
Disable 0 Disable endpoint OUT 5 (no response to OUT tokens)
Enable 1 Enable endpoint OUT 5 (response to OUT tokens)

4413_417 v1.9 822

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID I H G F E D C B A

Reset 0x00000001 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
ID R/W Field Value ID Value Description
G RW OUT6 Enable OUT endpoint 6
Disable 0 Disable endpoint OUT 6 (no response to OUT tokens)
Enable 1 Enable endpoint OUT 6 (response to OUT tokens)
H RW OUT7 Enable OUT endpoint 7
Disable 0 Disable endpoint OUT 7 (no response to OUT tokens)
Enable 1 Enable endpoint OUT 7 (response to OUT tokens)
I RW ISOOUT Enable ISO OUT endpoint 8
Disable 0 Disable ISO OUT endpoint 8
Enable 1 Enable ISO OUT endpoint 8

6.35.13.96 EPSTALL
Address offset: 0x518
STALL endpoints

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID C B A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W EP Select endpoint number
RME
B W IO Selects IN or OUT endpoint
RME
Out 0 Selects OUT endpoint
In 1 Selects IN endpoint
C W STALL Stall selected endpoint
RME
UnStall 0 Don't stall selected endpoint
Stall 1 Stall selected endpoint

6.35.13.97 ISOSPLIT
Address offset: 0x51C
Controls the split of ISO buffers

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW SPLIT Controls the split of ISO buffers
OneDir 0x0000 Full buffer dedicated to either ISO IN or OUT
HalfIN 0x0080 Lower half for IN, upper half for OUT

6.35.13.98 FRAMECNTR
Address offset: 0x520
Returns the current value of the start of frame counter

4413_417 v1.9 823

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R FRAMECNTR Returns the current value of the start of frame counter

6.35.13.99 LOWPOWER
Address offset: 0x52C
Controls USBD peripheral low power mode during USB suspend

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW LOWPOWER Controls USBD peripheral low-power mode during USB suspend
ForceNormal 0 Software must write this value to exit low power mode and before
performing a remote wake-up
LowPower 1 Software must write this value to enter low power mode after DMA and
software have finished interacting with the USB peripheral

6.35.13.100 ISOINCONFIG
Address offset: 0x530
Controls the response of the ISO IN endpoint to an IN token when no data is ready to be sent

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW RESPONSE Controls the response of the ISO IN endpoint to an IN token when no data is
ready to be sent
NoResp 0 Endpoint does not respond in that case
ZeroData 1 Endpoint responds with a zero-length data packet in that case

6.35.13.101 EPIN[0].PTR
Address offset: 0x600
Data pointer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PTR Data pointer

See the memory chapter for details about which memories are available for
EasyDMA.

6.35.13.102 EPIN[0].MAXCNT
Address offset: 0x604

4413_417 v1.9 824

 Peripherals

Maximum number of bytes to transfer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A
Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A- RW MAXCNT [64..0] Maximum number of bytes to transfer

6.35.13.103 EPIN[0].AMOUNT
Address offset: 0x608
Number of bytes transferred in the last transaction

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A- R AMOUNT Number of bytes transferred in the last transaction

6.35.13.104 EPIN[1].PTR
Address offset: 0x614
Data pointer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PTR Data pointer

See the memory chapter for details about which memories are available for
EasyDMA.

6.35.13.105 EPIN[1].MAXCNT
Address offset: 0x618
Maximum number of bytes to transfer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A- RW MAXCNT [64..0] Maximum number of bytes to transfer

6.35.13.106 EPIN[1].AMOUNT
Address offset: 0x61C
Number of bytes transferred in the last transaction

4413_417 v1.9 825

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A- R AMOUNT Number of bytes transferred in the last transaction

6.35.13.107 EPIN[2].PTR
Address offset: 0x628
Data pointer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PTR Data pointer

See the memory chapter for details about which memories are available for
EasyDMA.

6.35.13.108 EPIN[2].MAXCNT
Address offset: 0x62C
Maximum number of bytes to transfer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A- RW MAXCNT [64..0] Maximum number of bytes to transfer

6.35.13.109 EPIN[2].AMOUNT
Address offset: 0x630
Number of bytes transferred in the last transaction

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A- R AMOUNT Number of bytes transferred in the last transaction

6.35.13.110 EPIN[3].PTR
Address offset: 0x63C
Data pointer

4413_417 v1.9 826

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PTR Data pointer

See the memory chapter for details about which memories are available for
EasyDMA.

6.35.13.111 EPIN[3].MAXCNT
Address offset: 0x640
Maximum number of bytes to transfer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A- RW MAXCNT [64..0] Maximum number of bytes to transfer

6.35.13.112 EPIN[3].AMOUNT
Address offset: 0x644
Number of bytes transferred in the last transaction

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A- R AMOUNT Number of bytes transferred in the last transaction

6.35.13.113 EPIN[4].PTR
Address offset: 0x650
Data pointer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PTR Data pointer

See the memory chapter for details about which memories are available for
EasyDMA.

6.35.13.114 EPIN[4].MAXCNT
Address offset: 0x654
Maximum number of bytes to transfer

4413_417 v1.9 827

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A- RW MAXCNT [64..0] Maximum number of bytes to transfer

6.35.13.115 EPIN[4].AMOUNT
Address offset: 0x658
Number of bytes transferred in the last transaction

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A- R AMOUNT Number of bytes transferred in the last transaction

6.35.13.116 EPIN[5].PTR
Address offset: 0x664
Data pointer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PTR Data pointer

See the memory chapter for details about which memories are available for
EasyDMA.

6.35.13.117 EPIN[5].MAXCNT
Address offset: 0x668
Maximum number of bytes to transfer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A- RW MAXCNT [64..0] Maximum number of bytes to transfer

6.35.13.118 EPIN[5].AMOUNT
Address offset: 0x66C
Number of bytes transferred in the last transaction

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A- R AMOUNT Number of bytes transferred in the last transaction

4413_417 v1.9 828

 Peripherals

6.35.13.119 EPIN[6].PTR
Address offset: 0x678
Data pointer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PTR Data pointer

See the memory chapter for details about which memories are available for
EasyDMA.

6.35.13.120 EPIN[6].MAXCNT
Address offset: 0x67C
Maximum number of bytes to transfer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A- RW MAXCNT [64..0] Maximum number of bytes to transfer

6.35.13.121 EPIN[6].AMOUNT
Address offset: 0x680
Number of bytes transferred in the last transaction

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A- R AMOUNT Number of bytes transferred in the last transaction

6.35.13.122 EPIN[7].PTR
Address offset: 0x68C
Data pointer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PTR Data pointer

See the memory chapter for details about which memories are available for
EasyDMA.

6.35.13.123 EPIN[7].MAXCNT
Address offset: 0x690

4413_417 v1.9 829

 Peripherals

Maximum number of bytes to transfer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A
Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A- RW MAXCNT [64..0] Maximum number of bytes to transfer

6.35.13.124 EPIN[7].AMOUNT
Address offset: 0x694
Number of bytes transferred in the last transaction

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A- R AMOUNT Number of bytes transferred in the last transaction

6.35.13.125 ISOIN.PTR
Address offset: 0x6A0
Data pointer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PTR Data pointer

See the memory chapter for details about which memories are available for
EasyDMA.

6.35.13.126 ISOIN.MAXCNT
Address offset: 0x6A4
Maximum number of bytes to transfer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A- RW MAXCNT [1023..1] Maximum number of bytes to transfer

6.35.13.127 ISOIN.AMOUNT
Address offset: 0x6A8
Number of bytes transferred in the last transaction

4413_417 v1.9 830

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A- R AMOUNT Number of bytes transferred in the last transaction

6.35.13.128 EPOUT[0].PTR
Address offset: 0x700
Data pointer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PTR Data pointer

See the memory chapter for details about which memories are available for
EasyDMA.

6.35.13.129 EPOUT[0].MAXCNT
Address offset: 0x704
Maximum number of bytes to transfer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A- RW MAXCNT [64..0] Maximum number of bytes to transfer

6.35.13.130 EPOUT[0].AMOUNT
Address offset: 0x708
Number of bytes transferred in the last transaction

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A- R AMOUNT Number of bytes transferred in the last transaction

6.35.13.131 EPOUT[1].PTR
Address offset: 0x714
Data pointer

4413_417 v1.9 831

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PTR Data pointer

See the memory chapter for details about which memories are available for
EasyDMA.

6.35.13.132 EPOUT[1].MAXCNT
Address offset: 0x718
Maximum number of bytes to transfer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A- RW MAXCNT [64..0] Maximum number of bytes to transfer

6.35.13.133 EPOUT[1].AMOUNT
Address offset: 0x71C
Number of bytes transferred in the last transaction

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A- R AMOUNT Number of bytes transferred in the last transaction

6.35.13.134 EPOUT[2].PTR
Address offset: 0x728
Data pointer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PTR Data pointer

See the memory chapter for details about which memories are available for
EasyDMA.

6.35.13.135 EPOUT[2].MAXCNT
Address offset: 0x72C
Maximum number of bytes to transfer

4413_417 v1.9 832

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A- RW MAXCNT [64..0] Maximum number of bytes to transfer

6.35.13.136 EPOUT[2].AMOUNT
Address offset: 0x730
Number of bytes transferred in the last transaction

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A- R AMOUNT Number of bytes transferred in the last transaction

6.35.13.137 EPOUT[3].PTR
Address offset: 0x73C
Data pointer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PTR Data pointer

See the memory chapter for details about which memories are available for
EasyDMA.

6.35.13.138 EPOUT[3].MAXCNT
Address offset: 0x740
Maximum number of bytes to transfer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A- RW MAXCNT [64..0] Maximum number of bytes to transfer

6.35.13.139 EPOUT[3].AMOUNT
Address offset: 0x744
Number of bytes transferred in the last transaction

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A- R AMOUNT Number of bytes transferred in the last transaction

4413_417 v1.9 833

 Peripherals

6.35.13.140 EPOUT[4].PTR
Address offset: 0x750
Data pointer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PTR Data pointer

See the memory chapter for details about which memories are available for
EasyDMA.

6.35.13.141 EPOUT[4].MAXCNT
Address offset: 0x754
Maximum number of bytes to transfer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A- RW MAXCNT [64..0] Maximum number of bytes to transfer

6.35.13.142 EPOUT[4].AMOUNT
Address offset: 0x758
Number of bytes transferred in the last transaction

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A- R AMOUNT Number of bytes transferred in the last transaction

6.35.13.143 EPOUT[5].PTR
Address offset: 0x764
Data pointer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PTR Data pointer

See the memory chapter for details about which memories are available for
EasyDMA.

6.35.13.144 EPOUT[5].MAXCNT
Address offset: 0x768

4413_417 v1.9 834

 Peripherals

Maximum number of bytes to transfer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A
Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A- RW MAXCNT [64..0] Maximum number of bytes to transfer

6.35.13.145 EPOUT[5].AMOUNT
Address offset: 0x76C
Number of bytes transferred in the last transaction

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A- R AMOUNT Number of bytes transferred in the last transaction

6.35.13.146 EPOUT[6].PTR
Address offset: 0x778
Data pointer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PTR Data pointer

See the memory chapter for details about which memories are available for
EasyDMA.

6.35.13.147 EPOUT[6].MAXCNT
Address offset: 0x77C
Maximum number of bytes to transfer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A- RW MAXCNT [64..0] Maximum number of bytes to transfer

6.35.13.148 EPOUT[6].AMOUNT
Address offset: 0x780
Number of bytes transferred in the last transaction

4413_417 v1.9 835

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A- R AMOUNT Number of bytes transferred in the last transaction

6.35.13.149 EPOUT[7].PTR
Address offset: 0x78C
Data pointer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PTR Data pointer

See the memory chapter for details about which memories are available for
EasyDMA.

6.35.13.150 EPOUT[7].MAXCNT
Address offset: 0x790
Maximum number of bytes to transfer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A- RW MAXCNT [64..0] Maximum number of bytes to transfer

6.35.13.151 EPOUT[7].AMOUNT
Address offset: 0x794
Number of bytes transferred in the last transaction

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A- R AMOUNT Number of bytes transferred in the last transaction

6.35.13.152 ISOOUT.PTR
Address offset: 0x7A0
Data pointer

4413_417 v1.9 836

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW PTR Data pointer

See the memory chapter for details about which memories are available for
EasyDMA.

6.35.13.153 ISOOUT.MAXCNT
Address offset: 0x7A4
Maximum number of bytes to transfer

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A- RW MAXCNT Maximum number of bytes to transfer

6.35.13.154 ISOOUT.AMOUNT
Address offset: 0x7A8
Number of bytes transferred in the last transaction

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A- R AMOUNT Number of bytes transferred in the last transaction

6.35.14 Electrical specification

6.35.14.1 USB Electrical Specification

Symbol Description Min. Typ. Max. Units

RUSB,PU,ACTIVE Value of pull-up on D+, bus active (upstream device transmitting) 1425 2300 3090 Ω
RUSB,PU,IDLE Value of pull-up on D+, bus idle 900 1200 1575 Ω
tUSB,DETRST Minimum duration of an SE0 state to be detected as a USB reset condition µs
fUSB,CLK Frequency of local clock, USB active 48 MHz
fUSB,TOL Accuracy of local clock, USB active44 ±1000 ppm

TUSB,JITTER Jitter on USB local clock, USB active ±1 ns

6.36 WDT — Watchdog timer

A countdown watchdog timer using the low-frequency clock source (LFCLK) offers configurable and robust
protection against application lock-up.
The watchdog timer is started by triggering the START task.

44
The local clock can be stopped during USB suspend

4413_417 v1.9 837

 Peripherals

The watchdog can be paused during long CPU sleep periods for low power applications and when the
debugger has halted the CPU. The watchdog is implemented as a down-counter that generates a TIMEOUT
event when it wraps over after counting down to 0. When the watchdog timer is started through the
START task, the watchdog counter is loaded with the value specified in the CRV register. This counter is
also reloaded with the value specified in the CRV register when a reload request is granted.
The watchdog’s timeout period is given by the following equation:

timeout [s] = ( CRV + 1 ) / 32768

When started, the watchdog will automatically force the 32.768 kHz RC oscillator on as long as no other
32.768 kHz clock source is running and generating the 32.768 kHz system clock, see chapter CLOCK —
Clock control on page 156.

6.36.1 Reload criteria

The watchdog has eight separate reload request registers, which shall be used to request the watchdog to
reload its counter with the value specified in the CRV register. To reload the watchdog counter, the special
value 0x6E524635 needs to be written to all enabled reload registers.
One or more RR registers can be individually enabled through the RREN register.

6.36.2 Temporarily pausing the watchdog

By default, the watchdog will be active counting down the down-counter while the CPU is sleeping and
when it is halted by the debugger. It is possible to configure the watchdog to automatically pause while
the CPU is sleeping as well as when it is halted by the debugger.

6.36.3 Watchdog reset

A TIMEOUT event will automatically lead to a watchdog reset.
See Reset on page 88 for more information about reset sources. If the watchdog is configured to generate
an interrupt on the TIMEOUT event, the watchdog reset will be postponed with two 32.768 kHz clock
cycles after the TIMEOUT event has been generated. Once the TIMEOUT event has been generated, the
impending watchdog reset will always be effectuated.
The watchdog must be configured before it is started. After it is started, the watchdog’s configuration
registers, which comprise registers CRV, RREN, and CONFIG, will be blocked for further configuration.
The watchdog can be reset from several reset sources, see Reset behavior on page 89.
When the device starts running again, after a reset, or waking up from OFF mode, the watchdog
configuration registers will be available for configuration again.

6.36.4 Registers
Instances

Instance Base address Description

WDT 0x40010000 Watchdog timer

4413_417 v1.9 838

 Peripherals

Register overview

Register Offset Description

TASKS_START 0x000 Start the watchdog
EVENTS_TIMEOUT 0x100 Watchdog timeout
INTENSET 0x304 Enable interrupt
INTENCLR 0x308 Disable interrupt
RUNSTATUS 0x400 Run status
REQSTATUS 0x404 Request status
CRV 0x504 Counter reload value
RREN 0x508 Enable register for reload request registers
CONFIG 0x50C Configuration register
RR[0] 0x600 Reload request 0
RR[1] 0x604 Reload request 1
RR[2] 0x608 Reload request 2
RR[3] 0x60C Reload request 3
RR[4] 0x610 Reload request 4
RR[5] 0x614 Reload request 5
RR[6] 0x618 Reload request 6
RR[7] 0x61C Reload request 7

6.36.4.1 TASKS_START
Address offset: 0x000
Start the watchdog

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W TASKS_START Start the watchdog
Trigger 1 Trigger task

6.36.4.2 EVENTS_TIMEOUT
Address offset: 0x100
Watchdog timeout

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW EVENTS_TIMEOUT Watchdog timeout
NotGenerated 0 Event not generated
Generated 1 Event generated

6.36.4.3 INTENSET
Address offset: 0x304
Enable interrupt

4413_417 v1.9 839

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TIMEOUT Write '1' to enable interrupt for event TIMEOUT
Set 1 Enable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.36.4.4 INTENCLR
Address offset: 0x308
Disable interrupt

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A RW TIMEOUT Write '1' to disable interrupt for event TIMEOUT
Clear 1 Disable
Disabled 0 Read: Disabled
Enabled 1 Read: Enabled

6.36.4.5 RUNSTATUS
Address offset: 0x400
Run status

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A R RUNSTATUS Indicates whether or not the watchdog is running
NotRunning 0 Watchdog not running
Running 1 Watchdog is running

6.36.4.6 REQSTATUS
Address offset: 0x404
Request status

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID H G F E D C B A

Reset 0x00000001 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
ID R/W Field Value ID Value Description
A R RR0 Request status for RR[0] register
DisabledOrRequested0 RR[0] register is not enabled, or are already requesting reload
EnabledAndUnrequested
1 RR[0] register is enabled, and are not yet requesting reload
B R RR1 Request status for RR[1] register
DisabledOrRequested0 RR[1] register is not enabled, or are already requesting reload
EnabledAndUnrequested
1 RR[1] register is enabled, and are not yet requesting reload
C R RR2 Request status for RR[2] register

4413_417 v1.9 840

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID H G F E D C B A

Reset 0x00000001 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
ID R/W Field Value ID Value Description
DisabledOrRequested0 RR[2] register is not enabled, or are already requesting reload
EnabledAndUnrequested
1 RR[2] register is enabled, and are not yet requesting reload
D R RR3 Request status for RR[3] register
DisabledOrRequested0 RR[3] register is not enabled, or are already requesting reload
EnabledAndUnrequested
1 RR[3] register is enabled, and are not yet requesting reload
E R RR4 Request status for RR[4] register
DisabledOrRequested0 RR[4] register is not enabled, or are already requesting reload
EnabledAndUnrequested
1 RR[4] register is enabled, and are not yet requesting reload
F R RR5 Request status for RR[5] register
DisabledOrRequested0 RR[5] register is not enabled, or are already requesting reload
EnabledAndUnrequested
1 RR[5] register is enabled, and are not yet requesting reload
G R RR6 Request status for RR[6] register
DisabledOrRequested0 RR[6] register is not enabled, or are already requesting reload
EnabledAndUnrequested
1 RR[6] register is enabled, and are not yet requesting reload
H R RR7 Request status for RR[7] register
DisabledOrRequested0 RR[7] register is not enabled, or are already requesting reload
EnabledAndUnrequested
1 RR[7] register is enabled, and are not yet requesting reload

6.36.4.7 CRV
Address offset: 0x504
Counter reload value

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0xFFFFFFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ID R/W Field Value ID Value Description
A RW CRV [0xF..0xFFFFFFFF] Counter reload value in number of cycles of the 32.768 kHz clock

6.36.4.8 RREN
Address offset: 0x508
Enable register for reload request registers

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID H G F E D C B A

Reset 0x00000001 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
ID R/W Field Value ID Value Description
A RW RR0 Enable or disable RR[0] register
Disabled 0 Disable RR[0] register
Enabled 1 Enable RR[0] register
B RW RR1 Enable or disable RR[1] register
Disabled 0 Disable RR[1] register
Enabled 1 Enable RR[1] register
C RW RR2 Enable or disable RR[2] register
Disabled 0 Disable RR[2] register
Enabled 1 Enable RR[2] register
D RW RR3 Enable or disable RR[3] register
Disabled 0 Disable RR[3] register

4413_417 v1.9 841

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID H G F E D C B A

Reset 0x00000001 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
ID R/W Field Value ID Value Description
Enabled 1 Enable RR[3] register
E RW RR4 Enable or disable RR[4] register
Disabled 0 Disable RR[4] register
Enabled 1 Enable RR[4] register
F RW RR5 Enable or disable RR[5] register
Disabled 0 Disable RR[5] register
Enabled 1 Enable RR[5] register
G RW RR6 Enable or disable RR[6] register
Disabled 0 Disable RR[6] register
Enabled 1 Enable RR[6] register
H RW RR7 Enable or disable RR[7] register
Disabled 0 Disable RR[7] register
Enabled 1 Enable RR[7] register

6.36.4.9 CONFIG
Address offset: 0x50C
Configuration register

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID B A

Reset 0x00000001 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
ID R/W Field Value ID Value Description
A RW SLEEP Configure the watchdog to either be paused, or kept running, while the CPU
is sleeping
Pause 0 Pause watchdog while the CPU is sleeping
Run 1 Keep the watchdog running while the CPU is sleeping
B RW HALT Configure the watchdog to either be paused, or kept running, while the CPU
is halted by the debugger
Pause 0 Pause watchdog while the CPU is halted by the debugger
Run 1 Keep the watchdog running while the CPU is halted by the debugger

6.36.4.10 RR[0]
Address offset: 0x600
Reload request 0

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W RR Reload request register
Reload 0x6E524635 Value to request a reload of the watchdog timer

6.36.4.11 RR[1]
Address offset: 0x604
Reload request 1

4413_417 v1.9 842

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W RR Reload request register
Reload 0x6E524635 Value to request a reload of the watchdog timer

6.36.4.12 RR[2]
Address offset: 0x608
Reload request 2

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W RR Reload request register
Reload 0x6E524635 Value to request a reload of the watchdog timer

6.36.4.13 RR[3]
Address offset: 0x60C
Reload request 3

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W RR Reload request register
Reload 0x6E524635 Value to request a reload of the watchdog timer

6.36.4.14 RR[4]
Address offset: 0x610
Reload request 4

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W RR Reload request register
Reload 0x6E524635 Value to request a reload of the watchdog timer

6.36.4.15 RR[5]
Address offset: 0x614
Reload request 5

4413_417 v1.9 843

 Peripherals

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W RR Reload request register
Reload 0x6E524635 Value to request a reload of the watchdog timer

6.36.4.16 RR[6]
Address offset: 0x618
Reload request 6

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W RR Reload request register
Reload 0x6E524635 Value to request a reload of the watchdog timer

6.36.4.17 RR[7]
Address offset: 0x61C
Reload request 7

Bit number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ID A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Reset 0x00000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
ID R/W Field Value ID Value Description
A W RR Reload request register
Reload 0x6E524635 Value to request a reload of the watchdog timer

6.36.5 Electrical specification

6.36.5.1 Watchdog Timer Electrical Specification

Symbol Description Min. Typ. Max. Units

tWDT Time out interval 458 µs 36 h

4413_417 v1.9 844

7 Hardware and layout

7.1 Pin assignments

The pin assignment figures and tables describe the pinouts for the product variants of the chip.
The nRF52840 device provides flexibility regarding GPIO pin routing and configuration. However, some
pins have limitations or recommendations for pin configurations and uses.

7.1.1 aQFN73 ball assignments

The ball assignment figure and table in the following section describe the assignments for this variant of
the chip.

Figure 208: aQFN73 ball assignments, top view

4413_417 v1.9 845

 Hardware and layout

Pin Name Function Description Recommended usage

A8 P0.31 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
AIN7 Analog input Analog input
A10 P0.29 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
AIN5 Analog input Analog input
A12 P0.02 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
AIN0 Analog input Analog input
A14 P1.15 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
A16 P1.13 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
A18 DEC2 Power 1.3 V regulator supply decoupling
A20 P1.10 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
A22 VDD Power Power supply
A23 XC2 Analog input Connection for 32 MHz crystal
B1 VDD Power Power supply
B3 DCC Power DC/DC converter output
B5 DEC4 Power 1.3 V regulator supply decoupling Must be connected to DEC6 (pin
E24)
B7 VSS Power Ground
B9 P0.30 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
AIN6 Analog input Analog input
B11 P0.28 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
AIN4 Analog input Analog input
B13 P0.03 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
AIN1 Analog input Analog input
B15 P1.14 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
B17 P1.12 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
B19 P1.11 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
B24 XC1 Analog input Connection for 32 MHz crystal
C1 DEC1 Power 1.1 V regulator supply decoupling
D2 P0.00 Digital I/O General purpose I/O

XL1 Analog input Connection for 32.768 kHz crystal

D23 DEC3 Power Power supply, decoupling
E24 DEC6 Power 1.3 V regulator supply decoupling Must be connected to DEC4 (pin
B5)
F2 P0.01 Digital I/O General purpose I/O

XL2 Analog input Connection for 32.768 kHz crystal

F23 VSS_PA Power Ground (radio supply)
G1 P0.26 Digital I/O General purpose I/O
H2 P0.27 Digital I/O General purpose I/O
H23 ANT RF Single-ended radio antenna connection See Reference circuitry on page
856 for guidelines on how to
ensure good RF performance
J1 P0.04 Digital I/O General purpose I/O

AIN2 Analog input Analog input

J24 P0.10 Digital I/O General purpose I/O Standard drive, low frequency I/O
only

4413_417 v1.9 846

 Hardware and layout

Pin Name Function Description Recommended usage

NFC2 NFC input NFC antenna connection
K2 P0.05 Digital I/O General purpose I/O

AIN3 Analog input Analog input

L1 P0.06 Digital I/O General purpose I/O
L24 P0.09 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
NFC1 NFC input NFC antenna connection
M2 P0.07 Digital I/O General purpose I/O

TRACECLK Trace clock Trace buffer clock

N1 P0.08 Digital I/O General purpose I/O
N24 DEC5 Power 1.3 V regulator supply decoupling for build codes
Dxx and earlier.
Not connected
Not connected for build codes Fxx and later.
P2 P1.08 Digital I/O General purpose I/O
P23 P1.07 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
R1 P1.09 Digital I/O General purpose I/O

TRACEDATA3 Trace data Trace buffer TRACEDATA[3]

R24 P1.06 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
T2 P0.11 Digital I/O General purpose I/O

TRACEDATA2 Trace data Trace buffer TRACEDATA[2]

T23 P1.05 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
U1 P0.12 Digital I/O General purpose I/O

TRACEDATA1 Trace data Trace buffer TRACEDATA[1]

U24 P1.04 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
V23 P1.03 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
W1 VDD Power Power supply
W24 P1.02 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
Y2 VDDH Power High voltage power supply
Y23 P1.01 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
AA24 SWDCLK Debug Serial wire debug clock input for debug and
programming
AB2 DCCH Power DC/DC converter output
AC5 DECUSB Power USB 3.3 V regulator supply decoupling
AC9 P0.14 Digital I/O General purpose I/O
AC11 P0.16 Digital I/O General purpose I/O
AC13 P0.18 Digital I/O General purpose I/O QSPI/CSN

nRESET Configurable as pin RESET

AC15 P0.19 Digital I/O General purpose I/O QSPI/SCK
AC17 P0.21 Digital I/O General purpose I/O QSPI
AC19 P0.23 Digital I/O General purpose I/O QSPI
AC21 P0.25 Digital I/O General purpose I/O
AC24 SWDIO Debug Serial wire debug I/O for debug and programming
AD2 VBUS Power 5 V input for USB 3.3 V regulator
AD4 D- USB USB D-
AD6 D+ USB USB D+

4413_417 v1.9 847

 Hardware and layout

Pin Name Function Description Recommended usage

AD8 P0.13 Digital I/O General purpose I/O
AD10 P0.15 Digital I/O General purpose I/O
AD12 P0.17 Digital I/O General purpose I/O
AD14 VDD Power Power supply
AD16 P0.20 Digital I/O General purpose I/O
AD18 P0.22 Digital I/O General purpose I/O QSPI
AD20 P0.24 Digital I/O General purpose I/O
AD22 P1.00 Digital I/O General purpose I/O QSPI

TRACEDATA0 Trace data Trace buffer TRACEDATA[0]

Serial wire output (SWO)

AD23 VDD Power Power supply
Die pad VSS Power Ground pad Exposed die pad must be
connected to ground (VSS) for
proper device operation

Table 61: aQFN73 ball assignments

Note: For more information on standard drive, see GPIO — General purpose input/output on page
240. Low frequency I/O is a signal with a frequency up to 10 kHz.

7.1.2 QFN48 pin assignments

The pin assignment figure and table describe the assignments for this variant of the chip.

Note: VDD and VDDH are shortcircuited inside the package. Therefore the device is only usable in
Normal Voltage supply mode, and not High Voltage supply mode.
37
38
39
40
41
42
43
44
45
46
47
48

1 36
2 35
3 34
4 33
5 32
6 nRF5102
N52840 31
7 QFN48
QFN48 30
8 29
9 28
10 exposed die pad 27
11 26
12 25
13
14
15
16
17
18
19
20
21
22
23
24

Figure 209: QFN48 pin assignments, top view

4413_417 v1.9 848

 Hardware and layout

Pin Name Function Description Recommended usage

Left side of the chip
1 DEC1 Power 1.1 V Digital supply decoupling
2 P0.00 Digital I/O General purpose I/O

XL1 Analog input Connection for 32.768 kHz crystal

3 P0.01 Digital I/O General purpose I/O

XL2 Analog input Connection for 32.768 kHz crystal

4 P0.04 Digital I/O General purpose I/O

AIN2 Analog input Analog input

5 P0.05 Digital I/O General purpose I/O

AIN3 Analog input Analog input

6 P0.07 Digital I/O General purpose I/O

TRACECLK Trace clock Trace buffer clock

7 P0.08 Digital I/O General purpose I/O
8 P1.08 Digital I/O General purpose I/O
9 P1.09 Digital I/O General purpose I/O

TRACEDATA3 Trace data Trace buffer TRACEDATA[3]

10 P0.11 Digital I/O General purpose I/O

TRACEDATA2 Trace data Trace buffer TRACEDATA[2]

11 P0.12 Digital I/O General purpose I/O

TRACEDATA1 Trace data Trace buffer TRACEDATA[1]

12 VDD Power Power supply
Bottom side of chip
13 P0.13 Digital I/O General purpose I/O
14 P0.14 Digital I/O General purpose I/O
15 P0.17 Digital I/O General purpose I/O
16 P0.18 Digital I/O General purpose I/O QSPI/CSN

nRESET Configurable as pin RESET

17 VDD Power Power supply
18 P0.19 Digital I/O General purpose I/O QSPI/SCK
19 P0.20 Digital I/O General purpose I/O
20 P0.21 Digital I/O General purpose I/O QSPI
21 P0.22 Digital I/O General purpose I/O QSPI
22 P0.23 Digital I/O General purpose I/O QSPI
23 P0.24 Digital I/O General purpose I/O
24 P1.00 Digital I/O General purpose I/O QSPI

TRACEDATA0 Trace data Trace buffer TRACEDATA[0]

Serial wire output (SWO)

Right side of the chip
25 VDD Power Power supply
26 SWDIO Debug Serial wire debug I/O for debug and programming
27 SWDCLK Debug Serial wire debug clock input for debug and
programming
28 NC Not connected
29 P0.09 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
NFC1 NFC input NFC antenna connection
30 P0.10 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
NFC2 NFC input NFC antenna connection

4413_417 v1.9 849

 Hardware and layout

Pin Name Function Description Recommended usage

31 ANT RF Single-ended radio antenna connection See Reference circuitry on page
856 for guidelines on how to
ensure good RF performance
32 VSS_PA Power Ground (radio supply)
33 DEC6 Power 1.3 V regulator supply decoupling Must be connected to DEC4 (pin
46)
34 DEC3 Power Power supply, decoupling
35 XC1 Analog input Connection for 32 MHz crystal
36 XC2 Analog input Connection for 32 MHz crystal
Top side of the chip
37 VDD Power Power supply
38 P1.15 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
39 P0.03 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
AIN1 Analog input Analog input
40 P0.02 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
AIN0 Analog input Analog input
41 P0.28 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
AIN4 Analog input Analog input
42 P0.29 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
AIN5 Analog input Analog input
43 P0.30 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
AIN6 Analog input Analog input
44 P0.31 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
AIN7 Analog input Analog input
45 VSS Power Ground
46 DEC4 Power 1.3 V regulator supply decoupling Must be connected to DEC6 (pin
33)
47 DCC Power DC/DC converter output
48 VDD Power Power supply
Backside of the chip
Die pad VSS Power Ground pad Exposed die pad must be
connected to ground (VSS) for
proper device operation

Table 62: QFN48 pin assignments

7.1.3 WLCSP ball assignments

The ball assignment figure and table describe the assignments for this variant of the chip.

4413_417 v1.9 850

 Hardware and layout

Figure 210: WLCSP ball assignments, top view

4413_417 v1.9 851

 Hardware and layout

Pin Name Function Description Recommended usage

A1 XC1 Analog input Connection for 32 MHz crystal
A2 XC2 Analog input Connection for 32 MHz crystal
A3 P1.11 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
A4 P1.13 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
A5 P0.03 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
AIN1 Analog input Analog input
A6 P0.28 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
AIN4 Analog input Analog input
A7 P0.30 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
AIN6 Analog input Analog input
A8 DEC4 Power 1.3 V regulator supply decoupling

Must be connected to DEC6 (pin C2)

A9 DCC Power DC/DC converter output
A10 DEC1 Power 1.1 V regulator supply decoupling
B3 VDD Power Power supply
B4 P1.10 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
B5 P1.14 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
B6 P0.02 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
AIN0 Analog input Analog input
B7 VSS Power Ground
B8 VDD Power Power supply
B9 P0.00 Digital I/O General purpose I/O

XL1 Analog input Connection for 32.768 kHz crystal

B10 P0.01 Digital I/O General purpose I/O

XL2 Analog input Connection for 32.768 kHz crystal

C1 VSS_PA Power Ground (radio supply)
C2 DEC6 Power 1.3 V regulator supply decoupling

Must be connected to DEC4 (pin A8)

C4 VSS Power Ground
C5 P1.12 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
C6 P1.15 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
C7 P0.29 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
AIN5 Analog input Analog input
C8 P0.31 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
AIN7 Analog input Analog input
C9 P0.26 Digital I/O General purpose I/O
C10 P0.04 Digital I/O General purpose I/O

AIN2 Analog input Analog input

D3 VSS Power Ground
D4 VSS Power Ground
D5 VSS Power Ground
D6 VSS Power Ground
D7 VSS Power Ground
D8 VSS Power Ground

4413_417 v1.9 852

 Hardware and layout

Pin Name Function Description Recommended usage

D9 P0.27 Digital I/O General purpose I/O
D10 P0.05 Digital I/O General purpose I/O

AIN3 Analog input Analog input

E1 ANT RF Single-ended radio antenna connection See Reference circuitry on page
856 for guidelines on how to
ensure good RF performance
E2 P0.10 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
NFC2 NFC input NFC antenna connection
E3 P1.06 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
E4 VSS Power Ground
E5 VSS Power Ground
E6 VSS Power Ground
E7 VSS Power Ground
E8 VSS Power Ground
E9 P0.06 Digital I/O General purpose I/O
E10 P0.08 Digital I/O General purpose I/O
F1 P0.09 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
NFC1 NFC input NFC antenna connection
F2 DEC5 Power 1.3 V regulator supply decoupling for build codes
Dxx and earlier.
Not connected
Not connected for build codes Fxx and later.
F3 P1.03 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
F4 VSS Power Ground
F5 VSS Power Ground
F6 VSS Power Ground
F7 VSS Power Ground
F8 VSS Power Ground
F9 P0.07 Digital I/O General purpose I/O

TRACECLK Trace clock Trace buffer clock

F10 P1.09 Digital I/O General purpose I/O

TRACEDATA3 Trace data Trace buffer TRACEDATA[3]

G1 P1.07 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
G2 P1.05 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
G3 P1.02 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
G4 VSS Power Ground
G5 VSS Power Ground
G6 VSS Power Ground
G7 VSS Power Ground
G8 VSS Power Ground
G9 P1.08 Digital I/O General purpose I/O
G10 P0.12 Digital I/O General purpose I/O

TRACEDATA1 Trace data Trace buffer TRACEDATA[1]

H1 P1.04 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
H2 SWDCLK Digital input Serial wire debug clock input for debug and
programming

4413_417 v1.9 853

 Hardware and layout

Pin Name Function Description Recommended usage

H4 P0.24 Digital I/O General purpose I/O
H5 P0.23 Digital I/O General purpose I/O QSPI
H6 P0.16 Digital I/O General purpose I/O
H7 P0.13 Digital I/O General purpose I/O
H8 P0.11 Digital I/O General purpose I/O

TRACEDATA2 Trace data Trace buffer TRACEDATA[2]

H9 DCCH Power DC/DC converter output
H10 VDD Power Power supply
J1 P1.01 Digital I/O General purpose I/O Standard drive, low frequency I/O
only
J2 SWDIO Digital I/O Serial wire debug I/O for debug and programming
J3 P1.00 Digital I/O General purpose I/O QSPI

TRACEDATA0 Trace data Trace buffer TRACEDATA[0]

Serial wire output (SWO)

J4 P0.21 Digital I/O General purpose I/O QSPI
J5 P0.20 Digital I/O General purpose I/O
J6 P0.17 Digital I/O General purpose I/O
J7 P0.14 Digital I/O General purpose I/O
J8 D- USB USB D-
J9 VBUS Power 5 V input for USB 3.3 V regulator
J10 VDDH Power High voltage power supply
K1 VDD Power Power supply
K2 P0.25 Digital I/O General purpose I/O
K3 P0.22 Digital I/O General purpose I/O QSPI
K4 P0.19 Digital I/O General purpose I/O QSPI/SCK
K5 VDD Power Power supply
K6 P0.18 Digital I/O General purpose I/O QSPI/CSN

nRESET Configurable as pin reset

K7 P0.15 Digital I/O General purpose I/O
K8 D+ USB USB D+
K9 DECUSB Power USB 3.3 V regulator supply decoupling
K10 VSS Power Ground

Table 63: WLCSP ball assignments

Note: For more information on standard drive, see GPIO — General purpose input/output on page
240. Low frequency I/O is a signal with a frequency up to 10 kHz.

7.2 Mechanical specifications

The mechanical specifications for the packages show the dimensions in millimeters.

7.2.1 aQFN73 7 x 7 mm package

Dimensions in millimeters for the aQFN73 7 x 7 mm package.

4413_417 v1.9 854

 Hardware and layout

Figure 211: aQFN73 7 x 7 mm package

A A1 A2 A3 b D, E D2, E2 e e1 e2
Min. 0.00 0.20 6.90 4.75
Nom. 0.675 0.13 0.25 7.00 4.85 0.50 2.75 0.559
Max. 0.85 0.08 0.30 7.10 4.95

Table 64: aQFN73 dimensions in millimeters

7.2.2 QFN48 6 x 6 mm package

Dimensions in millimeters for the QFN48 6 x 6 mm package.

Figure 212: QFN48 6 x 6 mm package

4413_417 v1.9 855

 Hardware and layout

A A1 A3 b D, E D2, E2 e K L
Min. 0.80 0.00 0.15 5.9 4.5 0.2 0.35
Nom. 0.85 0.035 0.203 0.20 6.0 4.6 0.4 0.40
Max. 0.90 0.05 0.25 6.1 4.7 0.45

Table 65: QFN48 dimensions in millimeters

7.2.3 WLCSP 3.544 x 3.607 mm package

Dimensions in millimeters for the WLCSP 3.544 x 3.607 mm package.

Figure 213: WLCSP 3.544 x 3.607 mm package

A A1 A3 b D E D2 E2 e K L
Min. 0.464 0.148 0.303 0.184 3.514 3.577
Nom. 0.489 0.325 3.544 3.607 3.15 3.15 0.35 1.575 1.575
Max. 0.514 0.18 0.347 0.244 3.574 3.637

Table 66: WLCSP dimensions in millimeters

7.3 Reference circuitry

To ensure good RF performance when designing PCBs, it is highly recommended to use the PCB layouts
and component values provided by Nordic Semiconductor.
Documentation for the different package reference circuits, including Altium Designer files, PCB
layout files, and PCB production files can be downloaded from the product page for the nRF52840 on
www.nordicsemi.com.
In this section there are reference circuits for QIAA aQFN73, QFAA QFN48, and CKAA WLCSP showing the
components and component values to support on-chip features in a design.

Note: This is not a complete list of configurations, but all required circuitry is shown for further
configurations.

Some general guidance is summarized here:

4413_417 v1.9 856

 Hardware and layout

• External supply from VDD is only available when power is supplied to VDDH. External supply is
annotated with the VEXT net name.
• When supplying power from a USB source only, VBUS must be connected to VDDH if USB is to be used.
• Components required for DC/DC function are only needed if DC/DC mode is enabled for that regulator.
• NFC can be used in any configuration.
• USB can be used in any configuration as long as VBUS is supplied by the USB host.
• The schematics include an optional series resistor on the USB supply for improved immunity to
transient overvoltage during VBUS connection. Using the series resistor is recommended for new
designs.
• Two component values for the RF-Match network for the QIAA aQFN73 package are given and referred
to as v1.0 and v1.1 in the following tables. The reference schematics use v1.1 component values, which
are recommended for new designs to improve the margin for spurious emissions during regulatory
approval tests. However, both v1.0 and v1.1 are valid and can be used. All other RF parameters are
unchanged.
• A new reference design with four-component RF match has been added for the QIAA aQFN73 package.
The four-component RF match improves harmonic suppression when using Radio with TXPOWER equal
to 5dBm or above. However, previous 3 component RF-match designs are valid and can be used. Using
this four-component RF match is recommended for new designs.

Circuit configurations for QIAA aQFN73

Config no. Supply configuration Features that can be enabled for each configuration
example
VDDH VDD EXTSUPPLY DCDCEN0 DCDCEN1 USB NFC
Config. 1 USB (VDDH = N/A Yes No No Yes No
VBUS)
Config. 2 Battery/Ext. N/A Yes No No Yes No
regulator
Config. 3 N/A Battery/ No No No Yes No
Ext.
regulator
Config. 4 Battery/Ext. N/A Yes Yes Yes Yes No
regulator
Config. 5 N/A Battery/ No No Yes Yes Yes
Ext.
regulator
Config. 6 N/A Battery/ No No No No No
Ext.
regulator

Config. 71 Battery/Ext. N/A Yes Yes Yes Yes No

regulator

Table 67: Circuit configurations

1
Reference design with four-component RF match.

4413_417 v1.9 857

 Hardware and layout

Circuit configurations for QFAA QFN48

Config no. Supply configuration Features that can be enabled for each configuration
example

VDDH1 VDD EXTSUPPLY2 DCDCEN03 DCDCEN1 USB4 NFC

Config. 1 N/A Battery/Ext. N/A N/A Yes N/A No

regulator

Table 68: Circuit configurations

1
High Voltage supply mode cannot be used because the VDDH pin is not routed in the QFN48 package.
2
The external supply feature cannot be used because the VDDH pin is not routed in the QFN48 package.
3
DCDC for REG0 stage cannot be used because the VDDH pin is not routed in the QFN48 package.
4
USBD cannot be used because the USB pins are not routed in the QFN48 package.

Circuit configurations for CKAA WLCSP

Config no. Supply configuration Features that can be enabled for each configuration
example
VDDH VDD EXTSUPPLY DCDCEN0 DCDCEN1 USB NFC
Config. 1 USB (VDDH = N/A Yes No No Yes No
VBUS)
Config. 2 Battery/Ext. N/A Yes No No Yes No
regulator
Config. 3 N/A Battery/Ext. No No No Yes No
regulator
Config. 4 Battery/Ext. N/A Yes Yes Yes Yes No
regulator
Config. 5 N/A Battery/Ext. No No Yes Yes Yes
regulator
Config. 6 N/A Battery/Ext. No No No No No
regulator

Table 69: Circuit configurations

7.3.1 Circuit configuration no. 1 for QIAA aQFN73

Circuit configuration number 1 for QIAA aQFN73, showing the schematic and the bill of materials.

Config no. Supply configuration Enabled features

VDDH VDD EXTSUPPLY DCDCEN0 DCDCEN1 USB NFC
Config. 1 USB (VDDH = VBUS) N/A Yes No No Yes No

Table 70: Configuration summary for circuit configuration no. 1

4413_417 v1.9 858

 Hardware and layout

C15
1.0µF C13 C2
N.C.
12pF
X1
32MHz C1
VDD_nRF VDD_nRF
Optional

P0.31/AIN7
P0.30/AIN6
P0.29/AIN5
P0.28/AIN4
P0.02/AIN0
P0.03/AIN1
DEC1
C17 12pF

DEC4_6
C5 C14 C12

P1.15
P1.14
P1.13
P1.12

P1.10
P1.11
12pF 100nF 1.0µF 100nF
X2

A10

A12

A14

A16

A18

A20
A22
B13

B15

B17

B19
B11
A8
B1
B3
B5
B7

B9
32.768kHz

74
C18 C11

P0.03/AIN1

P1.13

P1.11
P1.15
GND
VDD

VSS

P0.29/AIN5

P1.14

P1.12
DEC2

P1.10
VDD
DCC
DEC4

P0.31/AIN7
P0.30/AIN6

P0.28/AIN4
P0.02/AIN0
12pF 100pF
A23 XC2
XC2 C10
C1 B24 XC1
DEC1 XC1
P0.00/XL1 D2 D23 DEC3
P0.00/XL1 DEC3
P0.01/XL2 F2 E24 DEC4_6
P0.26 G1
P0.01/XL2 DEC6
H23 L1 N.C. RF
P0.26 ANT
P0.27 H2 F23 4.7nH
P0.27 VSS_PA
P0.04/AIN2 J1 J24 P0.10/NFC2 C3 C4 C22
P0.04/AIN2 P0.10/NFC2
P0.05/AIN3 K2 L24 P0.09/NFC1 0.8pF 0.5pF N.C.
P0.05/AIN3 P0.09/NFC1
P0.06 L1 N24
P0.06 DEC5
P0.07 M2 P23 P1.07
P0.07 P1.07
P0.08 N1 R24 P1.06
P0.08 P1.06
P1.08 P2 T23 P1.05
P1.08 P1.05
P1.09 R1 U24 P1.04
P1.09 P1.04
P0.11 T2 V23 P1.03 C9
VDD_nRF P0.12 U1
P0.11 nRF52840 P1.03
W24 P1.02 820pF
P0.12 P1.02
W1 Y23 P1.01 Not required for Fxx and later
VEXT VDD P1.01
VBUS VBUS_nRF AB2 AC24SWDIO
R1 DCCH SWDIO
Y2 P0.18/RESET AA24SWDCLK VDD_nRF
VDDH SWDCLK
2R2 AC5 AD23
DECUSB VDD
C6 C19 C20 C8
VBUS

P0.13
P0.14
P0.15
P0.16
P0.17

P0.19
P0.20
P0.21
P0.22
P0.23
P0.24
P0.25
P1.00
VDD

Optional
4.7µF 4.7µF 4.7µF 100nF
D+
D-

U1

AC21
AC11

AC13
AD8

AC15

AD18
AD2
AD4
AD6

AC9

AD12

AD16
AC17

AC19

AD22
AD10

AD14

AD20 nRF52840-QIAA
VBUS_nRF
P0.18/RESET
P0.13
P0.14
P0.15
P0.16
P0.17

P0.19
P0.20
P0.21
P0.22
P0.23
P0.24
P0.25
P1.00
D+
D-

VDD_nRF

C7
100nF

Figure 214: Circuit configuration no. 1 schematic

Note: For PCB reference layouts, see the product page for the nRF52840 on www.nordicsemi.com.

4413_417 v1.9 859

 Hardware and layout

Designator Value v1.0 Value v1.1 Description Footprint

C1, C2, C17, 12 pF Capacitor, NP0, ±2% 0402
C18
C3 1 pF 0.8 pF Capacitor, NP0, ±10% 0402
C4 1 pF 0.5 pF Capacitor, NP0, ±10% 0402
C5, C7, C8, 100 nF Capacitor, X7R, ±10% 0402
C12
C6, C20 4.7 µF Capacitor, X7R, ±10% 0603
C9 820 pF Capacitor, NP0, ±5% 0402

Not required for Fxx and later

C10, C13, N.C. Not mounted 0402

C22
C11 100 pF Capacitor, NP0, ±5% 0402
C14, C15 1.0 µF Capacitor, X7R, ±10% 0603
C19 4.7 µF Capacitor, X7S, ±10% 0603
L1 3.9 nH 4.7 nH High frequency chip inductor ±5% 0402
R1 2R2 Resistor ±1%, 0.063W 0402
U1 nRF52840-QIAA Multiprotocol Bluetooth low energy, IEEE AQFN-73
802.15.4, ANT, and 2.4 GHz proprietary
System on Chip
X1 32 MHz XTAL SMD 2016, 32 MHz, Cl=8 pF, Total Tol: XTAL_2016
±40 ppm
X2 32.768 kHz XTAL SMD 3215, 32.768 kHz, Cl=9 pF, Total XTAL_3215
Tol: ±50 ppm

Table 71: Bill of material for circuit configuration no. 1

7.3.2 Circuit configuration no. 2 for QIAA aQFN73

Circuit configuration number 2 for QIAA aQFN73, showing the schematic and the bill of materials.

Config no. Supply configuration Enabled features

VDDH VDD EXTSUPPLY DCDCEN0 DCDCEN1 USB NFC
Config. 2 Battery/Ext. N/A Yes No No Yes No
regulator

Table 72: Configuration summary for circuit configuration no. 2

4413_417 v1.9 860

 Hardware and layout

C15
1.0µF C13 C2
N.C.
12pF
X1
32MHz C1
VDD_nRF VDD_nRF
Optional

P0.31/AIN7
P0.30/AIN6
P0.29/AIN5
P0.28/AIN4
P0.02/AIN0
P0.03/AIN1
DEC1
C17 12pF

DEC4_6
C5 C14 C12

P1.15
P1.14
P1.13
P1.12

P1.10
P1.11
12pF 100nF 1.0µF 100nF
X2

A10

A12

A14

A16

A18

A20
A22
B13

B15

B17

B19
B11
A8
B1
B3
B5
B7

B9
32.768kHz

74
C18 C11

P0.03/AIN1

P1.13

P1.11
P1.15
GND
VDD

VSS

P0.29/AIN5

P1.14

P1.12
DEC2

P1.10
VDD
DCC
DEC4

P0.31/AIN7
P0.30/AIN6

P0.28/AIN4
P0.02/AIN0
12pF 100pF
A23 XC2
XC2 C10
C1 B24 XC1
DEC1 XC1
P0.00/XL1 D2 D23 DEC3
P0.00/XL1 DEC3
P0.01/XL2 F2 E24 DEC4_6
P0.26 G1
P0.01/XL2 DEC6
H23 L1 N.C. RF
P0.26 ANT
P0.27 H2 F23 4.7nH
P0.27 VSS_PA
P0.04/AIN2 J1 J24 P0.10/NFC2 C3 C4 C22
P0.04/AIN2 P0.10/NFC2
P0.05/AIN3 K2 L24 P0.09/NFC1 0.8pF 0.5pF N.C.
P0.05/AIN3 P0.09/NFC1
P0.06 L1 N24
P0.06 DEC5
P0.07 M2 P23 P1.07
P0.07 P1.07
P0.08 N1 R24 P1.06
P0.08 P1.06
P1.08 P2 T23 P1.05
P1.08 P1.05
P1.09 R1 U24 P1.04
P1.09 P1.04
P0.11 T2 V23 P1.03 C9
VDD_nRF P0.12 U1
P0.11 nRF52840 P1.03
W24 P1.02 820pF
P0.12 P1.02
W1 Y23 P1.01 Not required for Fxx and later
VEXT VDD P1.01
VDDH AB2 AC24SWDIO
DCCH SWDIO
Y2 AA24SWDCLK VDD_nRF
AC5
VDDH P0.18/RESET SWDCLK
AD23
DECUSB VDD
C6 C19 C20 C8
VBUS

P0.13
P0.14
P0.15
P0.16
P0.17

P0.19
P0.20
P0.21
P0.22
P0.23
P0.24
P0.25
P1.00
VDD

4.7µF 4.7µF 4.7µF 100nF

D+
D-

U1

AC21
AC11

AC13
AD8

AC15

AD18
AD2
AD4
AD6

AC9

AD12

AD16
AC17

AC19

AD22
AD10

AD14

AD20 nRF52840-QIAA
VBUS
P0.18/RESET

C21
4.7µF
P0.13
P0.14
P0.15
P0.16
P0.17

P0.19
P0.20
P0.21
P0.22
P0.23
P0.24
P0.25
P1.00
D+
D-

VDD_nRF

C7
100nF

Figure 215: Circuit configuration no. 2 schematic

Note: For PCB reference layouts, see the product page for the nRF52840 on www.nordicsemi.com.

4413_417 v1.9 861

 Hardware and layout

Designator Value v1.0 Value v1.1 Description Footprint

C1, C2, C17, 12 pF Capacitor, NP0, ±2% 0402
C18
C3 1 pF 0.8 pF Capacitor, NP0, ±10% 0402
C4 1 pF 0.5 pF Capacitor, NP0, ±10% 0402
C5, C7, C8, 100 nF Capacitor, X7R, ±10% 0402
C12
C6, C20 4.7 µF Capacitor, X7R, ±10% 0603
C9 820 pF Capacitor, NP0, ±5% 0402

Not required for Fxx and later

C10, C13, N.C. Not mounted 0402

C22
C11 100 pF Capacitor, NP0, ±5% 0402
C14, C15 1.0 µF Capacitor, X7R, ±10% 0603
C19, C21 4.7 µF Capacitor, X7S, ±10% 0603
L1 3.9 nH 4.7 nH High frequency chip inductor ±5% 0402
U1 nRF52840-QIAA Multiprotocol Bluetooth low energy, IEEE AQFN-73
802.15.4, ANT, and 2.4 GHz proprietary
System on Chip
X1 32 MHz XTAL SMD 2016, 32 MHz, Cl=8 pF, Total Tol: XTAL_2016
±40 ppm
X2 32.768 kHz XTAL SMD 3215, 32.768 kHz, Cl=9 pF, Total XTAL_3215
Tol: ±50 ppm

Table 73: Bill of material for circuit configuration no. 2

7.3.3 Circuit configuration no. 3 for QIAA aQFN73

Circuit configuration number 3 for QIAA aQFN73, showing the schematic and the bill of materials.

Config no. Supply configuration Enabled features

VDDH VDD EXTSUPPLY DCDCEN0 DCDCEN1 USB NFC
Config. 3 N/A Battery/Ext. No No No Yes No
regulator

Table 74: Configuration summary for circuit configuration no. 3

4413_417 v1.9 862

 Hardware and layout

C15
1.0µF C13 C2
N.C.
12pF
X1
32MHz C1
VDD_nRF VDD_nRF
Optional

P0.31/AIN7
P0.30/AIN6
P0.29/AIN5
P0.28/AIN4
P0.02/AIN0
P0.03/AIN1
DEC1
C17 12pF

DEC4_6
C5 C14 C12

P1.15
P1.14
P1.13
P1.12

P1.10
P1.11
12pF 100nF 1.0µF 100nF
X2

A10

A12

A14

A16

A18

A20
A22
B13

B15

B17

B19
B11
A8
B1
B3
B5
B7

B9
32.768kHz

74
C18 C11

P0.03/AIN1

P1.13

P1.11
P1.15
GND
VDD

VSS

P0.29/AIN5

P1.14

P1.12
DEC2

P1.10
VDD
DCC
DEC4

P0.31/AIN7
P0.30/AIN6

P0.28/AIN4
P0.02/AIN0
12pF 100pF
A23 XC2
XC2 C10
C1 B24 XC1
DEC1 XC1
P0.00/XL1 D2 D23 DEC3
P0.00/XL1 DEC3
P0.01/XL2 F2 E24 DEC4_6
P0.26 G1
P0.01/XL2 DEC6
H23 L1 N.C. RF
P0.26 ANT
P0.27 H2 F23 4.7nH
P0.27 VSS_PA
P0.04/AIN2 J1 J24 P0.10/NFC2 C3 C4 C22
P0.04/AIN2 P0.10/NFC2
P0.05/AIN3 K2 L24 P0.09/NFC1 0.8pF 0.5pF N.C.
P0.05/AIN3 P0.09/NFC1
P0.06 L1 N24
P0.06 DEC5
P0.07 M2 P23 P1.07
P0.07 P1.07
P0.08 N1 R24 P1.06
P0.08 P1.06
P1.08 P2 T23 P1.05
P1.08 P1.05
P1.09 R1 U24 P1.04
P1.09 P1.04
P0.11 T2 V23 P1.03 C9
VDD_nRF P0.12 U1
P0.11 nRF52840 P1.03
W24 P1.02 820pF
P0.12 P1.02
W1 Y23 P1.01 Not required for Fxx and later
VDD P1.01
AB2 AC24SWDIO
DCCH SWDIO
Y2 AA24SWDCLK VDD_nRF
P0.18/RESET

VDDH SWDCLK
AC5 AD23
DECUSB VDD
C6 C20 C8
VBUS

P0.13
P0.14
P0.15
P0.16
P0.17

P0.19
P0.20
P0.21
P0.22
P0.23
P0.24
P0.25
P1.00
VDD

4.7µF 4.7µF 100nF

D+
D-

AC21 U1
AC11

AC13
AD8

AC15

AD18
AD2
AD4
AD6

AC9

AD12

AD16
AC17

AC19

AD22
AD10

AD14

AD20

nRF52840-QIAA
VBUS
P0.18/RESET

C21
4.7µF
P0.13
P0.14
P0.15
P0.16
P0.17

P0.19
P0.20
P0.21
P0.22
P0.23
P0.24
P0.25
P1.00
D+
D-

VDD_nRF

C7
100nF

Figure 216: Circuit configuration no. 3 schematic

Note: For PCB reference layouts, see the product page for the nRF52840 on www.nordicsemi.com.

4413_417 v1.9 863

 Hardware and layout

Designator Value v1.0 Value v1.1 Description Footprint

C1, C2, C17, 12 pF Capacitor, NP0, ±2% 0402
C18
C3 1 pF 0.8 pF Capacitor, NP0, ±10% 0402
C4 1 pF 0.5 pF Capacitor, NP0, ±10% 0402
C5, C7, C8, 100 nF Capacitor, X7R, ±10% 0402
C12
C6, C20 4.7 µF Capacitor, X7R, ±10% 0603
C9 820 pF Capacitor, NP0, ±5% 0402

Not required for Fxx and later

C10, C13, N.C. Not mounted 0402

C22
C11 100 pF Capacitor, NP0, ±5% 0402
C14, C15 1.0 µF Capacitor, X7R, ±10% 0603
C21 4.7 µF Capacitor, X7S, ±10% 0603
L1 3.9 nH 4.7 nH High frequency chip inductor ±5% 0402
U1 nRF52840-QIAA Multiprotocol Bluetooth low energy, IEEE AQFN-73
802.15.4, ANT, and 2.4 GHz proprietary
System on Chip
X1 32 MHz XTAL SMD 2016, 32 MHz, Cl=8 pF, Total Tol: XTAL_2016
±40 ppm
X2 32.768 kHz XTAL SMD 3215, 32.768 kHz, Cl=9 pF, Total XTAL_3215
Tol: ±50 ppm

Table 75: Bill of material for circuit configuration no. 3

7.3.4 Circuit configuration no. 4 for QIAA aQFN73

Circuit configuration number 4 for QIAA aQFN73, showing the schematic and the bill of materials.

Config no. Supply configuration Enabled features

VDDH VDD EXTSUPPLY DCDCEN0 DCDCEN1 USB NFC
Config. 4 Battery/Ext. N/A Yes Yes Yes Yes No
regulator

Table 76: Configuration summary for circuit configuration no. 4

4413_417 v1.9 864

 Hardware and layout

L3
15nH
C15 C16
1.0µF 47nF C13 C2
L2
N.C.
10µH
12pF
X1
32MHz C1
VDD_nRF VDD_nRF
Optional

P0.31/AIN7
P0.30/AIN6
P0.29/AIN5
P0.28/AIN4
P0.02/AIN0
P0.03/AIN1
DEC1
C17 12pF

DEC4_6
C5 C14 C12

P1.15
P1.14
P1.13
P1.12

P1.10
P1.11
12pF 100nF 1.0µF 100nF
X2

A10

A12

A14

A16

A18

A20
A22
B13

B15

B17

B19
B11
A8
B1
B3
B5
B7

B9
32.768kHz

74
C18 C11

P0.03/AIN1

P1.13

P1.11
P1.15
GND
VDD

VSS

P0.29/AIN5

P1.14

P1.12
DEC2

P1.10
VDD
DCC
DEC4

P0.31/AIN7
P0.30/AIN6

P0.28/AIN4
P0.02/AIN0
12pF 100pF
A23 XC2
XC2 C10
C1 B24 XC1
DEC1 XC1
P0.00/XL1 D2 D23 DEC3
P0.00/XL1 DEC3
P0.01/XL2 F2 E24 DEC4_6
P0.26 G1
P0.01/XL2 DEC6
H23 L1 N.C. RF
P0.26 ANT
P0.27 H2 F23 4.7nH
P0.27 VSS_PA
P0.04/AIN2 J1 J24 P0.10/NFC2 C3 C4 C22
P0.04/AIN2 P0.10/NFC2
P0.05/AIN3 K2 L24 P0.09/NFC1 0.8pF 0.5pF N.C.
P0.05/AIN3 P0.09/NFC1
P0.06 L1 N24
P0.06 DEC5
P0.07 M2 P23 P1.07
P0.07 P1.07
P0.08 N1 R24 P1.06
P0.08 P1.06
P1.08 P2 T23 P1.05
P1.08 P1.05
P1.09 R1 U24 P1.04
P1.09 P1.04
P0.11 T2 V23 P1.03 C9
VDD_nRF P0.12 U1
P0.11 nRF52840 P1.03
W24 P1.02 820pF
P0.12 P1.02
W1 Y23 P1.01 Not required for Fxx and later
VEXT VDD P1.01
VDD_HV L4 10µH AB2 AC24SWDIO
DCCH SWDIO
Y2 P0.18/RESET AA24SWDCLK VDD_nRF
VDDH SWDCLK
AC5 AD23
DECUSB VDD
C6 C19 C20 C8
VBUS

P0.13
P0.14
P0.15
P0.16
P0.17

P0.19
P0.20
P0.21
P0.22
P0.23
P0.24
P0.25
P1.00
VDD

4.7µF 4.7µF 4.7µF 100nF

D+
D-

U1
AC21
AC11

AC13
AD8

AC15

AD18
AD2
AD4
AD6

AC9

AD12

AD16
AC17

AC19

AD22
AD10

AD14

AD20 nRF52840-QIAA
VBUS
P0.18/RESET

C21
4.7µF
P0.13
P0.14
P0.15
P0.16
P0.17

P0.19
P0.20
P0.21
P0.22
P0.23
P0.24
P0.25
P1.00
D+
D-

VDD_nRF

C7
100nF

Figure 217: Circuit configuration no. 4 schematic for QIAA aQFN73

Note: For PCB reference layouts, see the product page for the nRF52840 on www.nordicsemi.com.

4413_417 v1.9 865

 Hardware and layout

Designator Value v1.0 Value v1.1 Description Footprint

C1, C2, C17, 12 pF Capacitor, NP0, ±2% 0402
C18
C3 1 pF 0.8 pF Capacitor, NP0, ±10% 0402
C4 1 pF 0.5 pF Capacitor, NP0, ±10% 0402
C5, C7, C8, 100 nF Capacitor, X7R, ±10% 0402
C12
C6, C20 4.7 µF Capacitor, X7R, ±10% 0603
C9 820 pF Capacitor, NP0, ±5% 0402

Not required for Fxx and later

C10, C13, N.C. Not mounted 0402

C22
C11 100 pF Capacitor, NP0, ±5% 0402
C14, C15 1.0 µF Capacitor, X7R, ±10% 0603
C16 47 nF Capacitor, X7R, ±10% 0402
C19, C21 4.7 µF Capacitor, X7S, ±10% 0603
L1 3.9 nH 4.7 nH High frequency chip inductor ±5% 0402
L2 10 µH Chip inductor, IDC, min = 50 mA, ±20% 0603
L3 15 nH High frequency chip inductor ±10% 0402
L4 10 µH Chip inductor, IDC, min = 80 mA, ±20% 0603
U1 nRF52840-QIAA Multiprotocol Bluetooth low energy, IEEE AQFN-73
802.15.4, ANT, and 2.4 GHz proprietary
System on Chip
X1 32 MHz XTAL SMD 2016, 32 MHz, Cl=8 pF, Total Tol: XTAL_2016
±40 ppm
X2 32.768 kHz XTAL SMD 3215, 32.768 kHz, Cl=9 pF, Total XTAL_3215
Tol: ±50 ppm

Table 77: Bill of material for circuit configuration no. 4

7.3.5 Circuit configuration no. 5 for QIAA aQFN73

Circuit configuration number 5 for QIAA aQFN73, showing the schematic and the bill of materials.

Config no. Supply configuration Enabled features

VDDH VDD EXTSUPPLY DCDCEN0 DCDCEN1 USB NFC
Config. 5 N/A Battery/Ext. No No Yes Yes Yes
regulator

Table 78: Configuration summary for circuit configuration no. 5

4413_417 v1.9 866

 Hardware and layout

L3
15nH
C15 C16
1.0µF 47nF C13 C2
L2
N.C.
10µH
12pF
X1
32MHz C1
VDD_nRF VDD_nRF
Optional

P0.31/AIN7
P0.30/AIN6
P0.29/AIN5
P0.28/AIN4
P0.02/AIN0
P0.03/AIN1
DEC1
C17 12pF

DEC4_6
C5 C14 C12

P1.15
P1.14
P1.13
P1.12

P1.10
P1.11
12pF 100nF 1.0µF 100nF
X2

A10

A12

A14

A16

A18

A20
A22
B13

B15

B17

B19
B11
A8
B1
B3
B5
B7

B9
32.768kHz

74
C18 C11

P0.03/AIN1

P1.13

P1.11
P1.15
GND
VDD

VSS

P0.29/AIN5

P1.14

P1.12
DEC2

P1.10
VDD
DCC
DEC4

P0.31/AIN7
P0.30/AIN6

P0.28/AIN4
P0.02/AIN0
12pF 100pF
A23 XC2
XC2 C10
C1 B24 XC1
DEC1 XC1
P0.00/XL1 D2 D23 DEC3
P0.00/XL1 DEC3
P0.01/XL2 F2 E24 DEC4_6
P0.26 G1
P0.01/XL2 DEC6
H23 L1 N.C. RF
P0.26 ANT
P0.27 H2 F23 4.7nH
P0.27 VSS_PA
P0.04/AIN2 J1 J24 C3 C4 C22
P0.04/AIN2 P0.10/NFC2
P0.05/AIN3 K2 L24 0.8pF 0.5pF N.C.
P0.05/AIN3 P0.09/NFC1
P0.06 L1 N24
P0.06 DEC5
P0.07 M2 P23 P1.07
P0.07 P1.07
P0.08 N1 R24 P1.06
P0.08 P1.06
P1.08 P2 T23 P1.05 CT3 CT4
P1.08 P1.05
P1.09 R1 U24 P1.04 NFC2
P1.09 P1.04
P0.11 T2 V23 P1.03 NFC1
VDD_nRF P0.12 U1
P0.11 nRF52840 P1.03
W24 P1.02
P0.12 P1.02
W1 Y23 P1.01 CT1 CT2
VDD P1.01
AB2 AC24SWDIO C9
DCCH SWDIO
Y2 AA24SWDCLK 820pF
P0.18/RESET

VDDH SWDCLK
AC5 AD23 Not required for Fxx and later
DECUSB VDD
C6 C20 VDD_nRF Note:
VBUS

P0.13
P0.14
P0.15
P0.16
P0.17

P0.19
P0.20
P0.21
P0.22
P0.23
P0.24
P0.25
P1.00
VDD

4.7µF 4.7µF The value of CT1, CT2, CT3 and CT4 must be
D+
D-

tuned to match the selected NFC antenna.

U1 C8
AC21
AC11

AC13
AD8

AC15

AD18
AD2
AD4
AD6

AC9

AD12

AD16
AC17

AC19

AD22
AD10

AD14

AD20

nRF52840-QIAA 100nF
VBUS
P0.18/RESET

C21
4.7µF
P0.13
P0.14
P0.15
P0.16
P0.17

P0.19
P0.20
P0.21
P0.22
P0.23
P0.24
P0.25
P1.00
D+
D-

VDD_nRF

C7
100nF

Figure 218: Circuit configuration no. 5 schematic

Note: For PCB reference layouts, see the product page for the nRF52840 on www.nordicsemi.com.

4413_417 v1.9 867

 Hardware and layout

Designator Value v1.0 Value v1.1 Description Footprint

C1, C2, C17, 12 pF Capacitor, NP0, ±2% 0402
C18
C3 1 pF 0.8 pF Capacitor, NP0, ±10% 0402
C4 1 pF 0.5 pF Capacitor, NP0, ±10% 0402
C5, C7, C8, 100 nF Capacitor, X7R, ±10% 0402
C12
C6, C20 4.7 µF Capacitor, X7R, ±10% 0603
C9 820 pF Capacitor, NP0, ±5% 0402
C10, C13, N.C. Not mounted 0402
C22
C11 100 pF Capacitor, NP0, ±5% 0402
C14, C15 1.0 µF Capacitor, X7R, ±10% 0603
C16 47 nF Capacitor, X7R, ±10% 0402
C21 4.7 µF Capacitor, X7S, ±10% 0603
CT1, CT2, Antenna dependent Capacitor, NP0, ±5% 0402
CT3, CT4
L1 3.9 nH 4.7 nH High frequency chip inductor ±5% 0402
L2 10 µH Chip inductor, IDC, min = 50 mA, ±20% 0603
L3 15 nH High frequency chip inductor ±10% 0402
U1 nRF52840-QIAA Multiprotocol Bluetooth low energy, IEEE AQFN-73
802.15.4, ANT, and 2.4 GHz proprietary
System on Chip
X1 32 MHz XTAL SMD 2016, 32 MHz, Cl=8 pF, Total Tol: XTAL_2016
±40 ppm
X2 32.768 kHz XTAL 3215, 32.768 kHz, Cl=9 pF, Total Tol: XTAL_3215
±50 ppm

Table 79: Bill of material for circuit configuration no. 5

7.3.6 Circuit configuration no. 6 for QIAA aQFN73

Circuit configuration number 6 for QIAA aQFN73, showing the schematic and the bill of materials.

Config no. Supply configuration Enabled features

VDDH VDD EXTSUPPLY DCDCEN0 DCDCEN1 USB NFC
Config. 6 N/A Battery/Ext. No No No No No
regulator

Table 80: Configuration summary for circuit configuration no. 6

4413_417 v1.9 868

 Hardware and layout

C15
1.0µF C13 C2
N.C.
12pF
X1
32MHz C1
VDD_nRF VDD_nRF
Optional

P0.31/AIN7
P0.30/AIN6
P0.29/AIN5
P0.28/AIN4
P0.02/AIN0
P0.03/AIN1
DEC1
C17 12pF

DEC4_6
C5 C14 C12

P1.15
P1.14
P1.13
P1.12

P1.10
P1.11
12pF 100nF 1.0µF 100nF
X2

A10

A12

A14

A16

A18

A20
A22
B13

B15

B17

B19
B11
A8
B1
B3
B5
B7

B9
32.768kHz

74
C18 C11

P0.03/AIN1

P1.13

P1.11
P1.15
GND
VDD

VSS

P0.29/AIN5

P1.14

P1.12
DEC2

P1.10
VDD
DCC
DEC4

P0.31/AIN7
P0.30/AIN6

P0.28/AIN4
P0.02/AIN0
12pF 100pF
A23 XC2
XC2 C10
C1 B24 XC1
DEC1 XC1
P0.00/XL1 D2 D23 DEC3
P0.00/XL1 DEC3
P0.01/XL2 F2 E24 DEC4_6
P0.26 G1
P0.01/XL2 DEC6
H23 L1 N.C. RF
P0.26 ANT
P0.27 H2 F23 4.7nH
P0.27 VSS_PA
P0.04/AIN2 J1 J24 P0.10/NFC2 C3 C4 C22
P0.04/AIN2 P0.10/NFC2
P0.05/AIN3 K2 L24 P0.09/NFC1 0.8pF 0.5pF N.C.
P0.05/AIN3 P0.09/NFC1
P0.06 L1 N24
P0.06 DEC5
P0.07 M2 P23 P1.07
P0.07 P1.07
P0.08 N1 R24 P1.06
P0.08 P1.06
P1.08 P2 T23 P1.05
P1.08 P1.05
P1.09 R1 U24 P1.04
P1.09 P1.04
P0.11 T2 V23 P1.03 C9
VDD_nRF P0.12 U1
P0.11 nRF52840 P1.03
W24 P1.02 820pF
P0.12 P1.02
W1 Y23 P1.01 Not required for Fxx and later
VDD P1.01
AB2 AC24SWDIO
DCCH SWDIO
Y2 AA24SWDCLK VDD_nRF
P0.18/RESET

VDDH SWDCLK
AC5 AD23
DECUSB VDD
C6 C8
VBUS

P0.13
P0.14
P0.15
P0.16
P0.17

P0.19
P0.20
P0.21
P0.22
P0.23
P0.24
P0.25
P1.00
VDD

4.7µF 100nF
D+
D-

U1
AC21
AC11

P0.18/RESET AC13
AD8

AC15

AD18
AD2
AD4
AD6

AC9

AD12

AD16
AC17

AC19

AD22
AD10

AD14

AD20

nRF52840-QIAA
P0.13
P0.14
P0.15
P0.16
P0.17

P0.19
P0.20
P0.21
P0.22
P0.23
P0.24
P0.25
P1.00

VDD_nRF

C7
100nF

Figure 219: Circuit configuration no. 6 schematic

Note: For PCB reference layouts, see the product page for the nRF52840 on www.nordicsemi.com.

4413_417 v1.9 869

 Hardware and layout

Designator Value v1.0 Value v1.1 Description Footprint

C1, C2, C17, 12 pF Capacitor, NP0, ±2% 0402
C18
C3 1 pF 0.8 pF Capacitor, NP0, ±10% 0402
C4 1 pF 0.5 pF Capacitor, NP0, ±10% 0402
C5, C7, C8, 100 nF Capacitor, X7R, ±10% 0402
C12
C6 4.7 µF Capacitor, X7R, ±10% 0603
C9 820 pF Capacitor, NP0, ±5% 0402

Not required for Fxx and later

C10, C13, N.C. Not mounted 0402

C22
C11 100 pF Capacitor, NP0, ±5% 0402
C14, C15 1.0 µF Capacitor, X7R, ±10% 0603
L1 3.9 nH 4.7 nH High frequency chip inductor ±5% 0402
U1 nRF52840-QIAA Multiprotocol Bluetooth low energy, IEEE AQFN-73
802.15.4, ANT, and 2.4 GHz proprietary
System on Chip
X1 32 MHz XTAL SMD 2016, 32 MHz, Cl=8 pF, Total Tol: XTAL_2016
±40 ppm
X2 32.768 kHz XTAL SMD 3215, 32.768 kHz, Cl=9 pF, Total XTAL_3215
Tol: ±50 ppm

Table 81: Bill of material for circuit configuration no. 6

7.3.7 Circuit configuration no. 7 for QIAA aQFN73

Circuit configuration number 7 for QIAAaQFN73, showing the schematic and the bill of materials.
This circuit configuration includes a four-component RF match for improved harmonic suppression when
using RADIO with TXPOWER ≥ 5 dBm.

Config no. Supply configuration Enabled features

VDDH VDD EXTSUPPLY DCDCEN0 DCDCEN1 USB NFC
Config. 7 Battery/Ext. N/A Yes Yes Yes Yes No
regulator

Table 82: Configuration summary for circuit configuration no. 7

4413_417 v1.9 870

 Hardware and layout

L3
15nH
C15 C16
1.0µF 47nF C13 C2
L2
N.C.
10µH
12pF
X1
32MHz C1
VDD_nRF VDD_nRF
Optional

P0.31/AIN7
P0.30/AIN6
P0.29/AIN5
P0.28/AIN4
P0.02/AIN0
P0.03/AIN1
DEC1
C17 12pF

DEC4_6
C5 C14 C12

P1.15
P1.14
P1.13
P1.12

P1.10
P1.11
12pF 100nF 1.0µF 100nF
X2

A10

A12

A14

A16

A18

A20
A22
B13

B15

B17

B19
B11
A8
B1
B3
B5
B7

B9
32.768kHz

74
C18 C11

P0.03/AIN1

P1.13

P1.11
P1.15
GND
VDD

VSS

P0.29/AIN5

P1.14

P1.12
DEC2

P1.10
VDD
DCC
DEC4

P0.31/AIN7
P0.30/AIN6

P0.28/AIN4
P0.02/AIN0
12pF 100pF
A23 XC2
XC2 C10
C1 B24 XC1
DEC1 XC1
P0.00/XL1 D2 D23 DEC3
P0.00/XL1 DEC3
P0.01/XL2 F2 E24 DEC4_6
P0.26 G1
P0.01/XL2 DEC6
H23 L1 N.C. L5 RF
P0.26 ANT
P0.27 H2 F23 4.7nH 2.2nH
P0.27 VSS_PA
P0.04/AIN2 J1 J24 P0.10/NFC2 C3 C4
P0.04/AIN2 P0.10/NFC2
P0.05/AIN3 K2 L24 P0.09/NFC1 1.0pF 1.2pF
P0.05/AIN3 P0.09/NFC1
P0.06 L1 N24
P0.06 DEC5
P0.07 M2 P23 P1.07
P0.07 P1.07
P0.08 N1 R24 P1.06
P0.08 P1.06
P1.08 P2 T23 P1.05
P1.08 P1.05
P1.09 R1 U24 P1.04
P1.09 P1.04
P0.11 T2 V23 P1.03 C9
VDD_nRF P0.12 U1
P0.11 nRF52840 P1.03
W24 P1.02 820pF
P0.12 P1.02
W1 Y23 P1.01 Not required for Fxx and later
VEXT VDD P1.01
VDD_HV L4 10µH AB2 AC24SWDIO
DCCH SWDIO
Y2 AA24SWDCLK VDD_nRF
P0.18/RESET
VDDH SWDCLK
AC5 AD23
DECUSB VDD
C6 C19 C20 C8
VBUS

P0.13
P0.14
P0.15
P0.16
P0.17

P0.19
P0.20
P0.21
P0.22
P0.23
P0.24
P0.25
P1.00
VDD

4.7µF 4.7µF 4.7µF 100nF

D+
D-

U1
AC21
AC11

AC13
AD8

AC15

AD18
AD2
AD4
AD6

AC9

AD12

AD16
AC17

AC19

AD22
AD10

AD14

AD20
nRF52840-QIAA
VBUS
P0.18/RESET

C21
4.7µF
P0.13
P0.14
P0.15
P0.16
P0.17

P0.19
P0.20
P0.21
P0.22
P0.23
P0.24
P0.25
P1.00
D+
D-

VDD_nRF

C7
100nF

Figure 220: Circuit configuration no. 7 schematic for QIAA aQFN73

Note: For PCB reference layouts, see the product page for the nRF52840 on www.nordicsemi.com.

4413_417 v1.9 871

 Hardware and layout

Designator Value Description Footprint

C1, C2, C17, 12 pF Capacitor, NP0, ±2% 0402
C18
C3 1 pF Capacitor, NP0, ±5% 0402
C4 1.2 pF Capacitor, NP0, ±5% 0402
C5, C7, C8, C12 100 nF Capacitor, X7R, ±10% 0402
C6, C20 4.7 µF Capacitor, X7R, ±10% 0603
C9 820 pF Capacitor, NP0, ±5% 0402

Not required for Fxx and later

C10, C13 N.C. Not mounted 0402

C11 100 pF Capacitor, NP0, ±5% 0402
C14, C15 1.0 µF Capacitor, X7R, ±10% 0603
C16 47 nF Capacitor, X7R, ±10% 0402
C19, C21 4.7 µF Capacitor, X7S, ±10% 0603
L1 4.7 nH High frequency chip inductor ±5% 0402
L2 10 µH Chip inductor, IDC, min = 50 mA, ±20% 0603
L3 15 nH High frequency chip inductor ±10% 0402
L4 10 µH Chip inductor, IDC, min = 80 mA, ±20% 0603
L5 2.2 nH High frequency chip inductor ±5% 0402
U1 nRF52840-QIAA Multiprotocol Bluetooth low energy, IEEE 802.15.4, AQFN-73
ANT, and 2.4 GHz proprietary System on Chip
X1 32 MHz XTAL SMD 2016, 32 MHz, Cl=8 pF, Total Tol: ±40 XTAL_2016
ppm
X2 32.768 kHz XTAL SMD 3215, 32.768 kHz, Cl=9 pF, Total Tol: ±50 XTAL_3215
ppm

Table 83: Bill of material for circuit configuration no. 7

7.3.8 Circuit configuration no. 1 for QFAA QFN48

Circuit configuration number 1 for QFAA QFN48, showing the schematic and the bill of materials.

Config no. Supply configuration Enabled features

VDDH VDD EXTSUPPLY DCDCEN0 DCDCEN1 USB NFC
Config. 1 N/A Battery/Ext. N/A N/A Yes N/A No
regulator

Table 84: Configuration summary for circuit configuration no. 1

4413_417 v1.9 872

 Hardware and layout

Figure 221: Circuit configuration no. 1 schematic

Note: For PCB reference layouts, see the product page for the nRF52840 on www.nordicsemi.com.

4413_417 v1.9 873

 Hardware and layout

Designator Value Description Footprint

C1, C2, C16, C17 12 pF Capacitor, NP0, ±2% 0201
C3 1.0 pF Capacitor, NP0, ±10% 0201
C4 1.2 pF Capacitor, NP0, ±10% 0201
C5, C6, C7, C8, 100 nF Capacitor, X5R, ±10% 0201
C12
C10 N.C. Not mounted 0201
C11 100 pF Capacitor, NP0, ±5% 0201
C13, C14 1.0 µF Capacitor, X5R, ±10% 0402
C15 47 nF Capacitor, X5R, ±10% 0201
L1 4.7 nH High frequency chip inductor ±5% 0201
L2 2.2 nH High frequency chip inductor ±5% 0201
L3 10 µH Chip inductor, IDC, min = 50 mA, ±20% 0603
L4 15 nH High frequency chip inductor ±10% 0402
U1 nRF52840- Multiprotocol Bluetooth low energy, IEEE 802.15.4, ANT, QFN48
QFAA and 2.4 GHz proprietary System on Chip
X1 32 MHz XTAL SMD 2016, 32 MHz, Cl=8 pF, Total Tol: ±30 ppm XTAL_2016
X2 32.768 kHz XTAL SMD 2012, 32.768 kHz, Cl=9 pF, Total Tol: ±50 ppm XTAL_2012

Table 85: Bill of material for circuit configuration no. 1

7.3.9 Circuit configuration no. 1 for CKAA WLCSP

Circuit configuration number 1 for CKAA WLCSP, showing the schematic and the bill of materials.

Config no. Supply configuration Enabled features

VDDH VDD EXTSUPPLY DCDCEN0 DCDCEN1 USB NFC
Config. 1 USB (VDDH = VBUS) N/A Yes No No Yes No

Table 86: Configuration summary for circuit configuration no. 1

4413_417 v1.9 874

 Hardware and layout

Figure 222: Circuit configuration no. 1 schematic for CKAA WLCSP

Note: For PCB reference layouts, see the product page for the nRF52840 on www.nordicsemi.com.

4413_417 v1.9 875

 Hardware and layout

Designator Value Description Footprint

C1, C2, C17, 12 pF Capacitor, NP0, ±2% 0201
C18
C3 1.0 pF Capacitor, NP0, ±5% 0201
C5, C7, C8, C12 100 nF Capacitor, X7R, ±10% 0201
C6, C20 4.7 µF Capacitor, X7R, ±10% 0603
C9 820 pF Capacitor, X7R, ±10% 0201

Not required for Fxx and later

C14, C15 1.0 µF Capacitor, X7R, ±10% 0603

C19 4.7 µF Capacitor, X7S, ±10% 0603
L1 3.9 nH High frequency chip inductor ±5% 0201
L5 4.7 nH High frequency chip inductor ±5% 0201
R1 2R2 Resistor, ±1%, 0.05W 0201
U1 nRF52840- Multiprotocol Bluetooth low energy, IEEE 802.15.4, WLCSP-94
CKAA ANT, and 2.4 GHz proprietary System on Chip
X1 32 MHz XTAL SMD 2016, 32 MHz, Cl=8 pF, Total Tol: ±40 ppm XTAL_2016
X2 32.768 kHz XTAL SMD 2012, 32.768 kHz, Cl=9 pF, Total Tol: ±50 XTAL_2012
ppm

Table 87: Bill of material for circuit configuration no. 1

7.3.10 Circuit configuration no. 2 for CKAA WLCSP

Circuit configuration number 2 for CKAA WLCSP, showing the schematic and the bill of materials.

Config no. Supply configuration Enabled features

VDDH VDD EXTSUPPLY DCDCEN0 DCDCEN1 USB NFC
Config. 2 Battery/Ext. regulator N/A Yes No No Yes No

Table 88: Configuration summary for circuit configuration no. 2

4413_417 v1.9 876

 Hardware and layout

Figure 223: Circuit configuration no. 2 schematic for CKAA WLCSP

Note: For PCB reference layouts, see the product page for the nRF52840 on www.nordicsemi.com.

4413_417 v1.9 877

 Hardware and layout

Designator Value Description Footprint

C1, C2, C17, 12 pF Capacitor, NP0, ±2% 0201
C18
C3 1.0 pF Capacitor, NP0, ±5% 0201
C5, C7, C8, C12 100 nF Capacitor, X7R, ±10% 0201
C6, C20 4.7 µF Capacitor, X7R, ±10% 0603
C9 820 pF Capacitor, X7R, ±10% 0201

Not required for Fxx and later

C14, C15 1.0 µF Capacitor, X7R, ±10% 0603

C19, C21 4.7 µF Capacitor, X7S, ±10% 0603
L1 3.9 nH High frequency chip inductor ±5% 0201
L5 4.7 nH High frequency chip inductor ±5% 0201
U1 nRF52840- Multiprotocol Bluetooth low energy, IEEE 802.15.4, ANT, WLCSP-94
CKAA and 2.4 GHz proprietary System on Chip
X1 32 MHz XTAL SMD 2016, 32 MHz, Cl=8 pF, Total Tol: ±40 ppm XTAL_2016
X2 32.768 kHz XTAL SMD 2012, 32.768 kHz, Cl=9 pF, Total Tol: ±50 ppm XTAL_2012

Table 89: Bill of material for circuit configuration no. 2

7.3.11 Circuit configuration no. 3 for CKAA WLCSP

Circuit configuration number 3 for CKAA WLCSP, showing the schematic and the bill of materials.

Config no. Supply configuration Enabled features

VDDH VDD EXTSUPPLY DCDCEN0 DCDCEN1 USB NFC
Config. 3 N/A Battery/Ext. No No No Yes No
regulator

Table 90: Configuration summary for circuit configuration no. 3

4413_417 v1.9 878

 Hardware and layout

Figure 224: Circuit configuration no. 3 schematic for CKAA WLCSP

Note: For PCB reference layouts, see the product page for the nRF52840 on www.nordicsemi.com.

4413_417 v1.9 879

 Hardware and layout

Designator Value Description Footprint

C1, C2, C17, C18 12 pF Capacitor, NP0, ±2% 0201
C3 1.0 pF Capacitor, NP0, ±5% 0201
C5, C7, C8, C12 100 nF Capacitor, X7R, ±10% 0201
C6, C20 4.7 µF Capacitor, X7R, ±10% 0603
C9 820 pF Capacitor, X7R, ±10% 0201

Not required for Fxx and later

C14, C15 1.0 µF Capacitor, X7R, ±10% 0603

C21 4.7 µF Capacitor, X7S, ±10% 0603
L1 3.9 nH High frequency chip inductor ±5% 0201
L5 4.7 nH High frequency chip inductor ±5% 0201
U1 nRF52840- Multiprotocol Bluetooth low energy, IEEE 802.15.4, ANT, WLCSP-94
CKAA and 2.4 GHz proprietary System on Chip
X1 32 MHz XTAL SMD 2016, 32 MHz, Cl=8 pF, Total Tol: ±40 ppm XTAL_2016
X2 32.768 kHz XTAL SMD 2012, 32.768 kHz, Cl=9 pF, Total Tol: ±50 ppm XTAL_2012

Table 91: Bill of material for circuit configuration no. 3

7.3.12 Circuit configuration no. 4 for CKAA WLCSP

Circuit configuration number 4 for CKAA WLCSP, showing the schematic and the bill of materials.

Config no. Supply configuration Enabled features

VDDH VDD EXTSUPPLY DCDCEN0 DCDCEN1 USB NFC
Config. 4 Battery/Ext. N/A Yes Yes Yes Yes No
regulator

Table 92: Configuration summary for circuit configuration no. 4

4413_417 v1.9 880

 Hardware and layout

Figure 225: Circuit configuration no. 4 schematic for CKAA WLCSP

Note: For PCB reference layouts, see the product page for the nRF52840 on www.nordicsemi.com.

4413_417 v1.9 881

 Hardware and layout

Designator Value Description Footprint

C1, C2, C17, 12 pF Capacitor, NP0, ±2% 0201
C18
C3 1.0 pF Capacitor, NP0, ±5% 0201
C5, C7, C8, C12 100 nF Capacitor, X7R, ±10% 0201
C6, C20 4.7 µF Capacitor, X7R, ±10% 0603
C9 820 pF Capacitor, X7R, ±10% 0201

Not required for Fxx and later

C14, C15 1.0 µF Capacitor, X7R, ±10% 0603

C16 47 nF Capacitor, X7R, ±10% 0201
C19, C21 4.7 µF Capacitor, X7S, ±10% 0603
L1 3.9 nH High frequency chip inductor ±5% 0201
L2 10 µH Chip inductor, IDC, min = 50 mA, ±20% 0603
L3 15 nH High frequency chip inductor ±10% 0402
L4 10 µH Chip inductor, IDC, min = 80 mA, ±10% 0603
L5 4.7 nH High frequency chip inductor ±5% 0201
U1 nRF52840- Multiprotocol Bluetooth low energy, IEEE 802.15.4, ANT, WLCSP-94
CKAA and 2.4 GHz proprietary System on Chip
X1 32 MHz XTAL SMD 2016, 32 MHz, Cl=8 pF, Total Tol: ±40 ppm XTAL_2016
X2 32.768 kHz XTAL SMD 2012, 32.768 kHz, Cl=9 pF, Total Tol: ±50 ppm XTAL_2012

Table 93: Bill of material for circuit configuration no. 4

7.3.13 Circuit configuration no. 5 for CKAA WLCSP

Circuit configuration number 5 for CKAA WLCSP, showing the schematic and the bill of materials.

Config no. Supply configuration Enabled features

VDDH VDD EXTSUPPLY DCDCEN0 DCDCEN1 USB NFC
Config. 5 N/A Battery/Ext. No No Yes Yes Yes
regulator

Table 94: Configuration summary for circuit configuration no. 5

4413_417 v1.9 882

 Hardware and layout

Figure 226: Circuit configuration no. 5 schematic for CKAA WLCSP

Note: For PCB reference layouts, see the product page for the nRF52840 on www.nordicsemi.com.

4413_417 v1.9 883

 Hardware and layout

Designator Value Description Footprint

C1, C2, C17, 12 pF Capacitor, NP0, ±2% 0201
C18
C3 1.0 pF Capacitor, NP0, ±5% 0201
C5, C7, C8, C12 100 nF Capacitor, X7R, ±10% 0201
C6, C20 4.7 µF Capacitor, X7R, ±10% 0603
C9 820 pF Capacitor, X7R, ±10% 0201

Not required for Fxx and later

C14, C15 1.0 µF Capacitor, X7R, ±10% 0603

C16 47 nF Capacitor, X7R, ± 10% 0201
C21 4.7 µF Capacitor, X7S, ± 10% 0603
CT1, CT2, CT3, Antenna Capacitor, X7R, ± 10% 0201
CT4 dependent
L1 3.9 nH High frequency chip inductor ±5% 0201
L2 10 µH Chip inductor, IDC, min = 50 mA, ±20% 0603
L3 15 nH High frequency chip inductor ±10% 0402
L5 4.7 nH High frequency chip inductor ±5% 0201
U1 nRF52840- Multiprotocol Bluetooth low energy, IEEE 802.15.4, ANT, WLCSP-94
CKAA and 2.4 GHz proprietary System on Chip
X1 32 MHz XTAL SMD 2016, 32 MHz, Cl=8 pF, Total Tol: ±40 ppm XTAL_2016
X2 32.768 kHz XTAL SMD 2012, 32.768 kHz, Cl=9 pF, Total Tol: ±50 ppm XTAL_2012

Table 95: Bill of material for circuit configuration no. 5

7.3.14 Circuit configuration no. 6 for CKAA WLCSP

Circuit configuration number 6 for CKAA WLCSP, showing the schematic and the bill of materials.

Config no. Supply configuration Enabled features

VDDH VDD EXTSUPPLY DCDCEN0 DCDCEN1 USB NFC
Config. 6 N/A Battery/Ext. No No No No No
regulator

Table 96: Configuration summary for circuit configuration no. 6

4413_417 v1.9 884

 Hardware and layout

Figure 227: Circuit configuration no. 6 schematic for CKAA WLCSP

Note: For PCB reference layouts, see the product page for the nRF52840 on www.nordicsemi.com.

4413_417 v1.9 885

 Hardware and layout

Designator Value Description Footprint

C1, C2, C17, 12 pF Capacitor, NP0, ±2% 0201
C18
C3 1.0 pF Capacitor, NP0, ±5% 0201
C5, C7, C8, C12 100 nF Capacitor, X7R, ±10% 0201
C6 4.7 µF Capacitor, X7R, ±10% 0603
C9 820 pF Capacitor, X7R, ±10% 0201

Not required for Fxx and later

C14, C15 1.0 µF Capacitor, X7R, ±10% 0603

L1 3.9 nH High frequency chip inductor ±5% 0201
L5 4.7 nH High frequency chip inductor ±5% 0201
U1 nRF52840- Multiprotocol Bluetooth low energy, IEEE 802.15.4, ANT, WLCSP-94
CKAA and 2.4 GHz proprietary System on Chip
X1 32 MHz XTAL SMD 2016, 32 MHz, Cl=8 pF, Total Tol: ±40 ppm XTAL_2016
X2 32.768 kHz XTAL SMD 2012, 32.768 kHz, Cl=9 pF, Total Tol: ±50 ppm XTAL_2012

Table 97: Bill of material for circuit configuration no. 6

7.3.15 PCB guidelines

A well designed PCB is necessary to achieve good RF performance. Poor layout can lead to loss in
performance or functionality.
A qualified RF layout for the IC and its surrounding components, including matching networks, can be
downloaded from www.nordicsemi.com.
To ensure optimal performance it is essential that you follow the schematics and layout references closely.
Especially in the case of the antenna matching circuitry (components between device pin ANT and the
antenna), any changes to the layout can change the behavior, resulting in degradation of RF performance
or a need to change component values. All reference circuits are designed for use with a 50 Ω single-
ended antenna.
A PCB with a minimum of two layers, including a ground plane, is recommended for optimal RF
performance. On PCBs with more than two layers, put a keep-out area on the inner layers directly below
the antenna matching circuitry (components between device pin ANT and the antenna) to reduce the stray
capacitances that influence RF performance.
A matching network is needed between the RF pin ANT and the antenna, to match the antenna
impedance (normally 50 Ω) to the optimum RF load impedance for the chip. For optimum performance,
the impedance for the matching network should be set as described in the recommended aQFN73
package reference circuitry from Circuit configuration no. 1 for QIAA aQFN73 on page 858, the
recommended QFN48 reference circuitry from Circuit configuration no. 1 for QFAA QFN48 on page 872,
or the recommended WLCSP reference circuitry from Circuit configuration no. 1 for CKAA WLCSP on page
874 depending on the package variant used in your design.
The DC supply voltage should be decoupled as close as possible to the VDD pins with high performance RF
capacitors. See the schematics for recommended decoupling capacitor values. The supply voltage for the
chip should be filtered and routed separately from the supply voltages of any digital circuitry.
Long power supply lines on the PCB should be avoided. All device grounds, VDD connections, and VDD
bypass capacitors must be connected as close as possible to the IC. For a PCB with a topside RF ground

4413_417 v1.9 886

 Hardware and layout

plane, the VSS pins should be connected directly to the ground plane. For a PCB with a bottom ground
plane, the best technique is to have via holes as close as possible to the VSS pads. A minimum of one via
hole should be used for each VSS pin.
Fast switching digital signals should not be routed close to the crystal or the power supply lines. Capacitive
loading of fast switching digital output lines should be minimized in order to avoid radio interference.
Avoid routing the 32MHz crystal lines close to antenna line and antenna ground.

7.3.16 PCB layout example

The PCB layout shown in the following figures is a reference layout for the aQFN™ package with internal
LDO setup and VBUS supply.

Note: Pay attention to how the capacitor C3 is grounded. It is not directly connected to the ground
plane, but grounded via VSS_PA pin F23. This is done to create additional filtering of harmonic
components.

For all available reference layouts, see the product page for the nRF52840 on www.nordicsemi.com.

Figure 228: Top silk layer

Figure 229: Top layer

4413_417 v1.9 887

 Hardware and layout

Figure 230: Mid layer 1

Figure 231: Mid layer 2

Figure 232: Bottom layer

Note: No components in bottom layer.

7.3.17 PMIC support

The nRF52 Series is comprehensively supported by Nordic Semiconductor's own range of PMICs (Power
Management Integrated Circuits). These PMICs are meticulously designed to enhance the performance
and efficiency of the nRF52 Series devices. This integration ensures the longest battery life and the highest
reliability for the end application. The synergy between the nRF52 Series and the Nordic PMICs highlights

4413_417 v1.9 888

 Hardware and layout

Nordic Semiconductor's commitment to providing a complete and cohesive solution for their customers'
needs in wireless technology applications.

7.4 Package thermal characteristics

A summary of the thermal characteristics for the different packages available for the IC can be found
below.

Symbol Package Typ. Unit

θJA,aQFN73 aQFN73 24.11 °C/W
θJA,QFN48 QFN48 22.37 °C/W
θJA,WLCSP WLCSP 36.55 °C/W

Table 98: Package thermal characteristics

Values obtained by simulation following the EIA/JESD51-2 for still air condition using JEDEC PCB.

7.5 Package Variation

The following describes the variation between this specification and a specific device package.

7.5.1 QFN48
The following section describes the package variation of the QFN48 package.
• The QFN48 package does not support USBD.
• VDD and VDDH are short circuited inside the QFN48 package. Therefore the device is only usable in
Normal Voltage supply mode, and not High Voltage supply mode. See POWER — Power supply on page
80 for more information.
The parameter variation when using the QFN48 package is as following:

Symbol Min. Typ. Max. Unit

PSENS,IT,SP,1M,BLE -95 dBm
PRF 7.545 dBm

Table 99: QFN48 package parameter variation

45
Achieved using Pos8dBm setting in RADIO.TXPOWER

4413_417 v1.9 889

8 Recommended operating conditions
The operating conditions are the physical parameters that the chip can operate within.

Symbol Parameter Min. Nom. Max. Units

VDD VDD supply voltage, independent of DCDC enable 1.7 3.0 3.6 V
VDDPOR VDD supply voltage needed during power-on reset 1.75 V
VDDH VDDH supply voltage, independent of DCDC enable 2.5 3.7 5.5 V
VBUS VBUS USB supply voltage 4.35 5.0 5.5 V
tR_VDD Supply rise time (0 V to 1.7 V) 60 ms
tR_VDDH Supply rise time (0 V to 3.7 V) 100 ms
TA Operating temperature -40 25 85 °C
TJ Junction temperature 90 °C

Table 100: Recommended operating conditions

Note: The on-chip power-on reset circuitry may not function properly for rise times longer than
the specified maximum.

8.1 WLCSP light sensitivity

All WLCSP package variants are sensitive to visible and close-range infrared light. This means that a final
product design must shield the chip properly, either by final product encapsulation or by shielding/coating
of the WLCSP device.
Some WLCSP package variants have a backside coating, where the marking side of the device is covered
with a light absorbing film, while the side edges and the ball side of the device are still exposed and need
to be protected. Other WLCSP package variants do not have any such protection.
The WLCSP package variant CKAA has a backside coating.

4413_417 v1.9 890

9 Absolute maximum ratings
Maximum ratings are the extreme limits to which the chip can be exposed for a limited amount of time
without permanently damaging it. Exposure to absolute maximum ratings for prolonged periods of time
may affect the reliability of the device.46

Note Min. Max. Unit

Supply voltages
VDD -0.3 +3.9 V
VDDH -0.3 +5.8 V
VBUS -0.3 +5.8 V
VSS 0 V
I/O pin voltage
VI/O, VDD ≤3.6 V -0.3 VDD + 0.3 V
VI/O, VDD >3.6 V -0.3 3.9 V
NFC antenna pin current
INFC1/2 80 mA
Radio
RF input level 10 dBm
Environmental aQFN73 package
Storage temperature -40 +125 °C
MSL Moisture Sensitivity Level 2
ESD HBM Human Body Model 2 kV
ESD HBM Class Human Body Model Class 2
ESD CDM Charged Device Model 450 V
Environmental QFN48 package
Storage temperature -40 +125 °C
MSL Moisture Sensitivity Level 2
ESD HBM Human Body Model 4 kV
ESD HBM Class Human Body Model Class 3A
ESD CDM Charged Device Model 1 kV
Environmental WLCSP 3.544 x 3.607 mm package
Storage temperature -40 +125 °C
MSL Moisture Sensitivity Level 1
ESD HBM Human Body Model 1 kV
ESD HBM Class Human Body Model Class 1C
ESD CDM Charged Device Model 500 V
Flash memory
Endurance 10 000 write/erase cycles
Retention at 85 °C 10 years

Table 101: Absolute maximum ratings

46
For accelerated life time testing (HTOL, etc) supply voltage should not exceed the recommended
operating conditions max value, see Recommended operating conditions on page 890.

4413_417 v1.9 891

 Absolute maximum ratings

4413_417 v1.9 892

10 Ordering information
This chapter contains information on device marking, ordering codes, and container sizes.

10.1 Device marking

The nRF52840 package is marked as shown in the following figure. Only the first two characters of the
function variant code are used in the <VV> entry.

N 5 2 8 4 0

<P P> <V V> <H> <P>

<Y Y> <W W> <L L>

Figure 233: Package marking

10.2 Box labels

The following figures show the box labels used for nRF52840.

PART NO.: (1P) <Nordic device order code>

TRACE CODE: (1T) <YYWWLL1/YYWWLL2/...YYWWLLn>

TRACE CODE QUANTITY: <.Quantity1/Quantity2/...Quantityn>

TOTAL QUANTITY: (Q) <Total inner box qty>

<Box ID> Pb e3 <HPF>
<Seal date>

Figure 234: Inner box label

4413_417 v1.9 893

 Ordering information

FROM: TO:

PART NO: (1P) <Nordic device order code>

<H><P><F>

CUSTOMER PO NO: (K) <Customer Purchase Order No.>

Pb

SALES ORDER NO: (14K) <Nordic Sales Order+Sales order line no.+
Delivery line no.>

SHIPMENT ID.: 2K <Nordic’s shipment ID.>

QUANTITY: (Q) <Total quantity>

COUNTRY OF ORIGIN.: 4L
CARTON NO:
<2- character code of COO>
x/n

DELIVERY NO.: (9K) <Shipper’s GROSS WEIGHT:

shipment no.)
KGS

Figure 235: Outer box label

10.3 Order code

The following are the order codes and definitions for nRF52840.
n R F 5 2 8 4 0 - <P P> <V V> - <C C>

Figure 236: Order code

4413_417 v1.9 894

 Ordering information

Abbrevitation Definition and implemented codes

N52/nRF52 nRF52 Series product
840 Part code
<PP> Package variant code
<VV> Function variant code
<H><P><F> Build code
H - Hardware version code
P - Production configuration code (production site, etc.)
F - Firmware version code (only visible on shipping container label)

<YY><WW><LL> Tracking code

YY - Year code
WW - Assembly week number
LL - Wafer lot code

<CC> Container code

Table 102: Abbreviations

10.4 Code ranges and values

Defined here are the nRF52840 code ranges and values.

<PP> Package Size (mm) Pin/Ball count Pitch (mm)

QI aQFN 7x7 73 0.5
QF QFN 6x6 48 0.4
CK WLCSP 3.544 x 3.607 94 0.35

Table 103: Package variant codes

<VV> Flash (kB) RAM (kB) Access port protection

AA 1024 256 Controlled by hardware
AA-F 1024 256 Controlled by hardware
and software

Table 104: Function variant codes

<H> Description
[A . . Z] Hardware version/revision identifier (incremental)

Table 105: Hardware version codes

4413_417 v1.9 895

 Ordering information

<P> Description
[0 . . 9] Production device identifier (incremental)
[A . . Z] Engineering device identifier (incremental)

Table 106: Production configuration codes

<F> Description
[A . . N, P . . Z] Version of preprogrammed firmware
[0] Delivered without preprogrammed firmware

Table 107: Production version codes

<YY> Description
[00 . . 99] Production year: 2000 to 2099

Table 108: Year codes

<WW> Description
[1 . . 52] Week of production

Table 109: Week codes

<LL> Description
[AA . . ZZ] Wafer production lot identifier

Table 110: Lot codes

<CC> Description
R7 7" Reel
R 13" Reel
T Tray

Table 111: Container codes

10.5 Product options

Defined here are the nRF52840 product options.

4413_417 v1.9 896

 Ordering information

Order code MOQ47 Comment

nRF52840-QIAA-R7 800 Not recommended for new designs

nRF52840-QIAA-R 3000 Not recommended for new designs
nRF52840-QIAA-T 260 Not recommended for new designs
nRF52840-QIAA-F-R 3000
nRF52840-QIAA-F-T 260
nRF52840-QIAA-F-R7 800
nRF52840-QFAA-F-R 3000
nRF52840-QFAA-F-R7 1000
nRF52840-CKAA-R 7000 Not recommended for new designs
nRF52840-CKAA-F-R 7000

Table 112: nRF52840 order codes

Order code Description

nRF52840-DK nRF52840 Development Kit

Table 113: Development tools order code

47
Minimum Ordering Quantity

4413_417 v1.9 897

11 Legal notices
By using this documentation you agree to our terms and conditions of use. Nordic Semiconductor may
change these terms and conditions at any time without notice.

Liability disclaimer
Nordic Semiconductor ASA reserves the right to make changes without further notice to the product to
improve reliability, function, or design. Nordic Semiconductor ASA does not assume any liability arising out
of the application or use of any product or circuits described herein.
Nordic Semiconductor ASA does not give any representations or warranties, expressed or implied, as to
the accuracy or completeness of such information and shall have no liability for the consequences of use
of such information. If there are any discrepancies, ambiguities or conflicts in Nordic Semiconductor’s
documentation, the Product Specification prevails.
Nordic Semiconductor ASA reserves the right to make corrections, enhancements, and other changes to
this document without notice.
Customer represents that, with respect to its applications, it has all the necessary expertise to create
and implement safeguards that anticipate dangerous consequences of failures, monitor failures and
their consequences, and lessen the likelihood of failures that might cause harm, and to take appropriate
remedial actions.
Nordic Semiconductor ASA assumes no liability for applications assistance or the design of customers’
products. Customers are solely responsible for the design, validation, and testing of its applications as well
as for compliance with all legal, regulatory, and safety-related requirements concerning its applications.
Nordic Semiconductor ASA’s products are not designed for use in life-critical medical equipment,
support appliances, devices, or systems where malfunction of Nordic Semiconductor ASA’s products can
reasonably be expected to result in personal injury. Customer may not use any Nordic Semiconductor
ASA’s products in life-critical medical equipment unless adequate design and operating safeguards by
customer’s authorized officers have been made. Customer agrees that prior to using or distributing
any life-critical medical equipment that include Nordic Semiconductor ASA’s products, customer will
thoroughly test such systems and the functionality of such products as used in such systems.
Customer will fully indemnify Nordic Semiconductor ASA and its representatives against any damages,
costs, losses, and/or liabilities arising out of customer’s non-compliance with this section.

RoHS and REACH statement

Refer to www.nordicsemi.com for complete hazardous substance reports, material composition reports,
and latest version of Nordic’s RoHS and REACH statements.

Trademarks
All trademarks, service marks, trade names, product names, and logos appearing in this documentation
are the property of their respective owners.

Copyright notice
© 2024 Nordic Semiconductor ASA. All rights are reserved. Reproduction in whole or in part is prohibited
without the prior written permission of the copyright holder.

4413_417 v1.9 898

 Legal notices

4413_417 v1.9 899