This document is the property of JSC IA Vozrozhdenie India Private Limited, DD Engineers, must not be passed on to any third

person or firm not authorised by us, nor be copied/made use of in full or part by

30-10-2023 PA For Review KG MA KP

DATE REV. NO. DESCRIPTION QC Checked Approved
REVISIONS
CONTRACTOR :

JSC IA VOZROZHDENIE INDIA PRIVATE LIMITED

such person or firm without our prior permission writing

CLIENT : AUTHORITY ENGINEER: :

NATIONAL HIGHWAYS AUTHORITY OF
DE
INDIA
VE
CONCESSIONAIRE : DESIGN CONSULTANT :

JSC IA VOZROZHDENIE INDIA PRIVATE LIMITED DD ENGINEERS

PROJECT : Construction of Six lane access-controlled Highway from Km 40+080 to Km 86+513.

JOB No. DDE-STR-LVUP-DN-001

TOTAL NO. OF PAGES 64 TITLE :

NAME SIGN DATE
QS KG 30-10-2023
LVUP DESIGN NOTE
CHKD MA 30-10-2023
APPD KP 30-10-2023
CODE REV.
DOC. No. D D E - S T R - L V U P - D N - 0 0 1
IRC PA

RELEASED FOR P PRELIMINARY TENDER INFORMATION APPROVAL CONSTRUCTION

 DESIGN OF LVUP

1 X 12 X 5.2
 Density of concrete 25 kN/m3
Density of dry soil 20 kN/m3
Density of submerged soil 11 kN/m3
Density of pavement 22 kN/m3
Coefficient of earth pressure at Rest = 0.50

No. of cell in Structure = 1

Clear Span = 12 Including Skew if Any
= 0

Size of Box = 1 X 12 X 5.2

Skew Angle 0.000 Degree
Opening Height = 5.200 m
Thickness of Vertical Wall = 0.700 m
Thickness of Top Slab(Precast Plank + Cast-in-situ Slab) = 0.700 m
Cast-in-situ Deck slab = 0.000 m
Precast plank = 0.000
Thickness of Bottom Slab = 0.750 m
Thickness Of Intermediate Wall = 0.000 m
Size of Haunch = 0.300 m
Camber Slope = 2.5%
Width of Crash Barrier = 0.50 m
Width of Box = 14.50 m
Thickness of pavement = 0.065 m
Effective Span [ IRC : 112 - cl 7.6.1.1 ] = m
Thickness of maximum earth fill = 0.00 m
Thickness of minimum earth fill = 0.00 m
Total length of Box in traffic direction = m

Soil Bearing Capacity = 70 kN/m2

Permissible Settlement = 10 mm
Subgrade Reaction = 1800 kN/m3

Design Parameter
Grade of Concrete fck = M 35
Grade of steel fyk Fe 500
Allowable Compressive Stress (Rare Combination) = 16.8 N/mm2
Allowable Compressive Stress (Quasi-Perm Combination) = 12.6 N/mm2
Material Factor for steel = 1.15
Material Factor for concrete = 1.5
Allowable Steel Tensile Stress (Rare Combination) 0.8fyk = 400.0 N/mm2
Clear Cover for earth face structural component = 75 mm
Clear Cover for inside face structural component = 45 mm
Clear Cover for cast-in-situ portion = 45 mm
Modulus of Elasticity Concrete Ecm = 30 GPa
Modulus of Elasticity Steel Es = 200 GPa
Load Calculation for Box Structure

Dead load
Self Weight of Structure has been calculated in STAAD Pro by "SELFWEIGHT-1"

Super imposed Dead Load

1. Top Slab

Thickness of Pavement 0.065 m

Thickness of Earth fill(cushion) 0.00 m

Load (UDL) due to Pavement on Top slab 1.43 kN/m

Load (UDL) due to Earth Fill on Top slab 0 kN/m

Earth Pressure

Thickness of Top Slab 0.700 m

Height of Top Haunch 0.3 m
Clear Height B/W top & bottom Slab 5.200 m
Height of bottom haunch 0.3 m
Thickness of Bottom Slab 0.750 m
Hfl from Sofit 0.100 m

Live load Surcharge

Equivelent Height 1.2 m
Uniform intensity of Loading 12 kN/m2

Height from top Dry condition Height from top Dry condition
Height b/w kN/m2 Height b/w elements kN/m2
elements (m) K0 = 0.50 (m) K0 = 0.50
0.415 0.415 4.150 4.150 0.415 0.415 4.150 4.150
0.350 0.765 3.500 7.650 0.350 0.765 3.500 7.650
0.300 1.065 3.000 10.650 0.300 1.065 3.000 10.650
1.230 2.295 12.300 22.950 at HFL > 0.100 0.865 0.000 8.650
0.535 2.830 5.350 28.300 1.230 2.295 19.065 30.815
0.535 3.365 5.350 33.650 0.615 2.910 9.533 40.348
0.535 3.900 5.350 39.000 0.615 3.525 9.533 49.880
0.535 4.435 5.350 44.350 0.615 4.140 9.533 59.413
1.230 5.665 12.300 56.650 0.615 4.755 9.533 68.945
0.300 5.965 3.000 59.650 1.230 5.985 19.065 88.010
0.375 6.340 3.750 63.400 0.300 6.285 4.650 92.660
0.375 6.660 5.813 98.473
 8.650

NORMAL HFL CASE

63.400 98.473

Sabgrade Reaction (Spring Constant Calculation)

Allowable Safe Bearing Capacity = 70

Permissible Settlement = 10
Modulus of Sabdrage Reaction = 1800
Node no Effective length K (kn/m3) KFY (KNM) Node no Effective length K (kn/m3) KFY (KNM)
1 0.525 1800 945
2 0.325 1800 585
3 0.484 1800 871
4 1.54825 1800 2787
5 2.4285 1800 4371
6 2.4285 1800 4371
7 2.4285 1800 4371
8 1.54825 1800 2787
9 0.484 1800 871
10 0.325 1800 585
11 0.175 1800 315

5.0 CALCULATIONS FOR UNIFORM TEMPERATURE RISE

UNIFORM TEMPERATURE CASE (According to IRC:6-2014,Clause 215.2)
The top slab is designed for the effects of uniform temperature rise across the deck depth.
Maximum Air Shade Temperature = 48.5
Minimum Air Shade temperature = 1.7
Difference between Maximum and Minimum Air Shade temperature 46.8 = >20
Maximum Effective Bridge Temperature = 33.4
Minimum Effective Bridge temperature = 13.4
For Expansion,temperature Rise = 33.4
For Contraction,Temperature Fall = 33.4
For Expansion,Strain on Top Slab = 0.000401
For Contraction,Strain on Top Slab = 0.000401
5.1 CALCULATIONS FOR TEMPERATURE GRADIENT
Effective bridge temperature
Maximum air shade temperature 48.5 /degree celcius
Minimum air shade temperature 1.7
Mean of max and min temperature 23.4
Bridge temperature to be assumed 13.4 33.4
Temperature Rise 47.5
Temperature fall -2.5
Rise Drop
Critical difference 34.1 35.9
Temperature force 4296.6 kn
Effect of temperature Gradient
The Box has been checked for temperature differential

F= Ec*a*Dt*A
Ec Modulus of Elasticity of concrete 3E+06 t/m^2
a Coefficient of thermal expansion 1E-05 /deg celcius(as per IRC 6)
Dt Temperature Differential
A X sectional area of of section where temperature differential is Dt

Average thickness of Deck = 700 mm

Effect of temperature rise:

4 13.8

0.15 1 2

0.21 3
0.700 m

0.19

0.15 4

2.1

Sr. no. Dt b t A=bxt F(force) Acting at Ecc. e Moment

m m sqm kn m m knm
1 4 1 0.15 0.15 216 0.07500 -0.0750 -16.2
2 6.9 1 0.075 0.075 186.3 0.05000 -0.0500 -9.315
3 2 1 0.105 0.105 75.6 0.22000 -0.2200 -16.632
4 1.05 1 0.15 0.15 56.7 0.65000 -0.6500 -36.855
SF 534.6 Moment -79.002
Effect of temperature drop:

9.9 0.7

2 1 0.14

3
0.175
0.700 m

0.175

6
0.14
4 5
5.8 0.8

Acting at
Sr. no. Dt b t A=bxt F(force) Ecc. e Moment
from top
m m sqm kn m m knm
1 0.7 1 0.14 0.14 35.28 0.07000 -0.0700 -2.4696
2 4.95 1 0.14 0.14 249.48 0.04667 -0.0467 -11.642
3 0.35 1 0.175 0.175 22.05 0.19833 -0.1983 -4.3733
4 2.9 1 0.14 0.14 146.16 0.65333 -0.6533 -95.491
5 0.8 1 0.14 0.14 40.32 0.63 -0.6300 -25.402
6 0.4 1 0.175 0.175 25.2 0.5016667 -0.5017 -12.642
SF 518.49 Moment -152.02
 STAAD MODEL

12 13 14 15 16 17 18 19 20 21 22

31 40
30 39

29 38

28 37

27 36

26 35

25 34

24 33
23 32

1 2 3 4 5 6 7 8 9 10 11
Y
Z X
Load 101

NODE NUMBER DETAIL AS PER STAAD MODEL

11 12 13 14 15 16 17 18 19 20
30 40

29 39

28 38

27 37

26 36

25 35

24 34

23 33

22 32

21 31
1 2 3 4 5 6 7 8 9 10
Y
Z X
Load 101

MEMBER NUMBER DETAIL AS PER STAAD MODEL

Effective Width Calculation
the calculation of effective live load and position is calculated as per IRC 112-2011

Effective Span of Section = 12.35 Load increment = 0.8283 span 1 span 2 span 3 span 4 span 5
Width of Box nos = 16
Outer Span 12.35 1 = 1.2955 12.35 1 0.35 0 0 0 0
Inner Span 0.1 0 12.35 0 0 0 0 2 0.3 0.3 0.3 0.3 0.3
As per Annexure B-3 of IRC-112-2011 6.175 3 0.668 0.668 0.668 0.668 0.668
A
12.35 4 2.4285 -0.547 -0.547 -0.547 2.4285
beff = αa(1-a/l0)+bt 12.35 5 2.4285 -0.547 -0.547 -0.547 2.4285
B
12.35 6 2.4285 -0.547 -0.547 -0.547 2.4285
Where 12.35 7 2.4285 -0.547 -0.547 -0.547 2.4285
C
a= Distance of CG of concentrated Load from nearer Support 12.35 8 0.668 0.668 0.668 0.668 0.668
bt= Breadth of Concentrated area of load 0.99 12.35 9 0.3 0.3 0.3 0.3 0.3
D
α= ratio of b/l0 2.6436 12.35 10 0.35 0.35 0.35 0.35 0.35
12.35 12.35 0.1 0.1 0.1 12
E
Impact Factor = 1.25 12.35
Effective Span = 12.35

load loading P1 P2 P3 P4 P5 P6 P7
case postion 170 170 170 170 120 120 80
positio a membe position load/m positio a membe positio load/m positio a membe positio load/m positio a membe positio load/m positio a membe positio load/m positio a membe positio load/m positio a membe positio load/m
n r no n r no n n r no n n r no n n r no n n r no n n r no n
0 -1.37 -4.42 -5.79 -7.92 -9.44 -13.4
1 0.000 0 0.000 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
2 0.828 0.8283 0.828 13 0.18 42.82 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
3 1.657 1.6567 1.657 14 0.34 31.66 0.29 0.29 11 0.29 61.41 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
4 2.485 2.485 2.485 14 1.17 26.02 1.12 1.12 13 0.47 37.94 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
5 3.313 3.3133 3.313 14 2.00 22.78 1.94 1.94 14 0.63 29.31 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
6 4.142 4.1417 4.142 15 0.40 20.84 2.77 2.77 14 1.45 24.70 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
7 4.970 4.97 4.970 15 1.22 19.73 3.60 3.60 14 2.28 21.99 0.55 0.55 12 0.20 49.31 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
8 5.798 5.7983 5.798 15 2.05 19.23 4.43 4.43 15 0.68 20.38 1.38 1.38 14 0.06 34.51 0.01 0.01 11 0.01 104.99 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
9 6.627 6.6267 5.723 16 0.45 19.25 5.26 5.26 15 1.51 19.49 2.21 2.21 14 0.89 27.56 0.84 0.84 13 0.19 42.65 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
10 7.455 7.455 4.895 16 1.28 19.80 6.09 6.09 15 2.34 19.18 3.04 3.04 14 1.72 23.69 1.67 1.67 14 0.35 31.58 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
11 8.283 8.2833 4.067 16 2.11 20.98 6.91 5.44 16 0.74 19.38 3.86 3.86 15 0.12 21.38 2.49 2.49 14 1.18 25.98 0.36 0.36 12 0.01 39.02 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
12 9.112 9.1117 3.238 17 0.51 23.01 7.74 4.61 16 1.57 20.13 4.69 4.69 15 0.95 20.03 3.32 3.32 14 2.00 22.75 1.19 1.19 13 0.54 26.01 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
13 9.940 9.94 2.410 17 1.34 26.40 8.57 3.78 16 2.40 21.56 5.52 5.52 15 1.77 19.34 4.15 4.15 15 0.40 20.82 2.02 2.02 14 0.70 20.31 0.50 0.50 12 0.15 35.81 0.00 0.00 11 0.00 0.00
14 10.768 10.768 1.582 17 2.16 32.36 9.40 2.95 17 0.79 23.99 6.35 6.00 16 0.17 19.19 4.98 4.98 15 1.23 19.72 2.85 2.85 14 1.53 17.22 1.33 1.33 14 0.01 24.78 0.00 0.00 11 0.00 0.00
15 11.597 11.597 0.753 18 0.56 44.36 10.23 2.12 17 1.62 28.08 7.18 5.17 16 1.00 19.55 5.81 5.81 15 2.06 19.23 3.68 3.68 14 2.36 15.39 2.16 2.16 14 0.84 19.67 0.00 0.00 11 0.00 0.00
16 12.425 - - - - - 11.06 1.30 18 0.02 35.51 8.01 4.35 16 1.83 20.50 6.64 5.72 16 0.46 19.25 4.51 4.51 15 0.76 14.31 2.99 2.99 14 1.67 16.85 0.00 0.00 11 0.00 0.00
17 - - - - - - 11.88 0.47 19 0.18 51.74 8.83 3.52 17 0.23 22.21 7.46 4.89 16 1.29 19.81 5.33 5.33 15 1.59 13.72 3.81 3.81 15 0.07 15.17 0.00 0.00 11 0.00 0.00
18 - - - - - - - - - - - 9.66 2.69 17 1.06 25.06 8.29 4.06 16 2.12 20.99 6.16 6.16 15 2.42 13.54 4.64 4.64 15 0.90 14.18 0.68 0.68 13 0.03 21.63
19 - - - - - - - - - - - 10.49 1.86 17 1.89 29.94 9.12 3.23 17 0.52 23.03 6.99 5.36 16 0.82 13.71 5.47 5.47 15 1.72 13.67 1.51 1.51 14 0.19 15.57
20 - - - - - - - - - - - 11.32 1.03 18 0.29 39.21 9.95 2.40 17 1.34 26.45 7.82 4.53 16 1.64 14.28 6.30 6.05 16 0.12 13.54 2.34 2.34 14 1.02 12.61
21 - - - - - - - - - - - 12.15 0.20 20 0.15 69.96 10.78 1.57 17 2.17 32.45 8.65 3.70 17 0.04 15.35 7.13 5.22 16 0.95 13.78 3.17 3.17 14 1.85 10.94
22 - - - - - - - - - - - - - - - - 11.61 0.74 18 0.57 44.54 9.48 2.88 17 0.87 17.14 7.96 4.40 16 1.78 14.42 4.00 4.00 15 0.25 9.94
23 - - - - - - - - - - - - - - - - - - - - - 10.30 2.05 17 1.70 20.18 8.78 3.57 17 0.18 15.58 4.82 4.82 15 1.08 9.35
24 - - - - - - - - - - - - - - - - - - - - - 11.13 1.22 18 0.10 25.76 9.61 2.74 17 1.01 17.54 5.65 5.65 15 1.91 9.07
25 - - - - - - - - - - - - - - - - - - - - - 11.96 0.39 19 0.26 38.28 10.44 1.91 17 1.84 20.87 6.48 5.87 16 0.31 9.04
26 - - - - - - - - - - - - - - - - - - - - - - - - - - 11.27 1.08 18 0.24 27.13 7.31 5.04 16 1.13 9.25
27 - - - - - - - - - - - - - - - - - - - - - - - - - - 12.10 0.25 20 0.10 45.57 8.14 4.21 16 1.96 9.75
28 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8.97 3.39 17 0.36 10.62
29 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 9.79 2.56 17 1.19 12.08
30 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 10.62 1.73 17 2.02 14.60
31 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 11.45 0.90 18 0.42 19.51
32 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 12.28 0.07 20 0.28 42.43
33 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
34 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
35 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
36 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
37 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
38 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
39 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
40 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
41 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
42 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
43 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Effective Width Calculation
the calculation of effective live load and position is calculated as per IRC 112-2011

Effective Span of Section = 12.35 Load increment = 0.35786 span 1 span 2 span 3 span 4 span 5
Width of Box nos = 16
Outer Span 12.35 1 = 1.296 12.35 1 0.35 0 0 0 0
Inner Span 0.1 0 12.35 0 0 0 0 2 0.3 0.3 0.3 0.3 0.3
As per Annexure B-3 of IRC-112-2011 6.175 3 0.668 0.668 0.668 0.668 0.668
A
12.35 4 2.429 -0.55 -0.547 -0.55 2.4285
beff = αa(1-a/l0)+bt 12.35 5 2.429 -0.55 -0.547 -0.55 2.4285
B
12.35 6 2.429 -0.55 -0.547 -0.55 2.4285
Where 12.35 7 2.429 -0.55 -0.547 -0.55 2.4285
C
a= Distance of CG of concentrated Load from nearer Support 12.35 8 0.668 0.668 0.668 0.668 0.668
bt= Breadth of Concentrated area of load 0.99 12.35 9 0.3 0.3 0.3 0.3 0.3
D
α= ratio of b/l0 2.644 12.35 10 0.35 0.35 0.35 0.35 0.35
12.35 12.4 0.1 0.1 0.1 12
E
Impact Factor = 1.25 12.35
Effective Span = 12.35

load loading P1 P2 P3 P4 P5 P6 P7
case postion 58.3335 116.667 116.667 116.667 116.667 116.667 58.3335
positio a member position load/m positio a membe positi load/m positio a membe positi load/m positio a memb positi load/m positi a membe positi load/m positi a membe positi load/m positi a membe positio load/m
n no n r no on n r no on n er no on on r no on on r no on on r no n
0 -0.60 -1.20 -1.80 -2.40 -3.00 -3.60
1 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
2 0.36 0.36 0.36 12 0.01 19.10 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
3 0.72 0.72 0.72 13 0.07 15.51 0.12 0.12 11 0.12 56.39 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
4 1.07 1.07 1.07 13 0.42 13.23 0.47 0.47 12 0.12 35.36 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
5 1.43 1.43 1.43 14 0.11 11.64 0.83 0.83 13 0.18 29.34 0.23 0.23 11 0.23 45.85 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
6 1.79 1.79 1.79 14 0.47 10.47 1.19 1.19 13 0.54 25.31 0.59 0.59 12 0.24 33.12 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
7 2.15 2.15 2.15 14 0.83 9.58 1.55 1.55 14 0.23 22.44 0.95 0.95 13 0.30 27.87 0.35 0.35 11 0.35 38.75 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
8 2.51 2.51 2.51 14 1.19 8.89 1.91 1.91 14 0.59 20.31 1.31 1.31 13 0.66 24.28 0.71 0.71 13 0.06 31.18 0.11 0.11 11 0.11 57.63 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
9 2.86 2.86 2.86 14 1.54 8.35 2.26 2.26 14 0.94 18.68 1.66 1.66 14 0.34 21.69 1.06 1.06 13 0.41 26.57 0.46 0.46 12 0.11 35.59 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
10 3.22 3.22 3.22 14 1.90 7.91 2.62 2.62 14 1.30 17.41 2.02 2.02 14 0.70 19.74 1.42 1.42 14 0.10 23.36 0.82 0.82 13 0.17 29.49 0.22 0.22 11 0.22 46.65 0.00 0.00 11 0.00 0.00
11 3.58 3.58 3.58 14 2.26 7.56 2.98 2.98 14 1.66 16.40 2.38 2.38 14 1.06 18.24 1.78 1.78 14 0.46 21.00 1.18 1.18 13 0.53 25.41 0.58 0.58 12 0.23 33.31 0.00 0.00 11 0.00 0.00
12 3.94 3.94 3.94 15 0.19 7.28 3.34 3.34 14 2.02 15.59 2.74 2.74 14 1.42 17.05 2.14 2.14 14 0.82 19.21 1.54 1.54 14 0.22 22.52 0.94 0.94 13 0.29 28.00 0.34 0.34 11 0.34 19.65
13 4.29 4.29 4.29 15 0.55 7.06 3.69 3.69 14 2.38 14.93 3.09 3.09 14 1.78 16.11 2.49 2.49 14 1.18 17.82 1.89 1.89 14 0.58 20.37 1.29 1.29 13 0.64 24.37 0.69 0.69 13 0.04 15.67
14 4.65 4.65 4.65 15 0.91 6.89 4.05 4.05 15 0.31 14.41 3.45 3.45 14 2.13 15.36 2.85 2.85 14 1.53 16.73 2.25 2.25 14 0.93 18.73 1.65 1.65 14 0.33 21.76 1.05 1.05 13 0.40 13.34
15 5.01 5.01 5.01 15 1.26 6.76 4.41 4.41 15 0.66 14.00 3.81 3.81 15 0.06 14.75 3.21 3.21 14 1.89 15.85 2.61 2.61 14 1.29 17.44 2.01 2.01 14 0.69 19.79 1.41 1.41 14 0.09 11.72
16 5.37 5.37 5.37 15 1.62 6.66 4.77 4.77 15 1.02 13.68 4.17 4.17 15 0.42 14.27 3.57 3.57 14 2.25 15.15 2.97 2.97 14 1.65 16.42 2.37 2.37 14 1.05 18.28 1.77 1.77 14 0.45 10.53
17 5.73 5.73 5.73 15 1.98 6.61 5.13 5.13 15 1.38 13.45 4.53 4.53 15 0.78 13.89 3.93 3.93 15 0.18 14.58 3.33 3.33 14 2.01 15.61 2.73 2.73 14 1.41 17.09 2.13 2.13 14 0.81 9.63
18 6.08 6.08 6.08 15 2.34 6.58 5.48 5.48 15 1.74 13.28 4.88 4.88 15 1.14 13.60 4.28 4.28 15 0.54 14.14 3.68 3.68 14 2.37 14.95 3.08 3.08 14 1.77 16.14 2.48 2.48 14 1.17 8.93
19 6.44 6.44 5.91 16 0.27 6.59 5.84 5.84 15 2.09 13.19 5.24 5.24 15 1.49 13.38 4.64 4.64 15 0.89 13.79 4.04 4.04 15 0.29 14.43 3.44 3.44 14 2.12 15.38 2.84 2.84 14 1.52 8.38
20 6.80 6.80 5.55 16 0.62 6.63 6.20 6.15 16 0.02 13.16 5.60 5.60 15 1.85 13.24 5.00 5.00 15 1.25 13.52 4.40 4.40 15 0.65 14.01 3.80 3.80 15 0.05 14.77 3.20 3.20 14 1.88 7.94
21 7.16 7.16 5.19 16 0.98 6.70 6.56 5.79 16 0.38 13.20 5.96 5.96 15 2.21 13.17 5.36 5.36 15 1.61 13.33 4.76 4.76 15 1.01 13.69 4.16 4.16 15 0.41 14.28 3.56 3.56 14 2.24 7.58
22 7.52 7.52 4.84 16 1.34 6.82 6.92 5.44 16 0.74 13.30 6.32 6.04 16 0.14 13.16 5.72 5.72 15 1.97 13.21 5.12 5.12 15 1.37 13.45 4.52 4.52 15 0.77 13.90 3.92 3.92 15 0.17 7.30
23 7.87 7.87 4.48 16 1.70 6.97 7.27 5.08 16 1.10 13.47 6.67 5.68 16 0.50 13.22 6.07 6.07 15 2.33 13.16 5.47 5.47 15 1.73 13.29 4.87 4.87 15 1.13 13.61 4.27 4.27 15 0.53 7.07
24 8.23 8.23 4.12 16 2.06 7.16 7.63 4.72 16 1.46 13.72 7.03 5.32 16 0.86 13.35 6.43 5.92 16 0.26 13.18 5.83 5.83 15 2.08 13.19 5.23 5.23 15 1.48 13.39 4.63 4.63 15 0.88 6.90
25 8.59 8.59 3.76 16 2.41 7.41 7.99 4.36 16 1.81 14.05 7.39 4.96 16 1.21 13.54 6.79 5.56 16 0.61 13.26 6.19 6.16 16 0.01 13.16 5.59 5.59 15 1.84 13.25 4.99 4.99 15 1.24 6.76
26 8.95 8.95 3.40 17 0.34 7.73 8.35 4.00 16 2.17 14.48 7.75 4.60 16 1.57 13.82 7.15 5.20 16 0.97 13.40 6.55 5.80 16 0.37 13.19 5.95 5.95 15 2.20 13.17 5.35 5.35 15 1.60 6.67
27 9.30 9.30 3.05 17 0.70 8.11 8.70 3.65 17 0.10 15.01 8.10 4.25 16 1.93 14.18 7.50 4.85 16 1.33 13.62 6.90 5.45 16 0.73 13.30 6.30 6.05 16 0.13 13.16 5.70 5.70 15 1.96 6.61
28 9.66 9.66 2.69 17 1.06 8.60 9.06 3.29 17 0.46 15.68 8.46 3.89 16 2.29 14.64 7.86 4.49 16 1.69 13.93 7.26 5.09 16 1.09 13.47 6.66 5.69 16 0.49 13.22 6.06 6.06 15 2.32 6.58
29 10.02 10.02 2.33 17 1.42 9.21 9.42 2.93 17 0.82 16.52 8.82 3.53 17 0.22 15.22 8.22 4.13 16 2.05 14.32 7.62 4.73 16 1.45 13.71 7.02 5.33 16 0.84 13.34 6.42 5.93 16 0.24 6.59
30 10.38 10.38 1.97 17 1.77 9.99 9.78 2.57 17 1.17 17.56 9.18 3.17 17 0.57 15.93 8.58 3.77 16 2.40 14.81 7.98 4.37 16 1.80 14.04 7.38 4.97 16 1.20 13.54 6.78 5.57 16 0.60 6.63
31 10.74 10.74 1.61 17 2.13 11.00 10.14 2.21 17 1.53 18.88 9.54 2.81 17 0.93 16.83 8.94 3.41 17 0.33 15.43 8.34 4.01 16 2.16 14.46 7.74 4.61 16 1.56 13.81 7.14 5.21 16 0.96 6.70
32 11.09 11.09 1.26 18 0.06 12.35 10.49 1.86 17 1.89 20.57 9.89 2.46 17 1.29 17.96 9.29 3.06 17 0.69 16.20 8.69 3.66 17 0.09 15.00 8.09 4.26 16 1.92 14.17 7.49 4.86 16 1.32 6.81
33 11.45 11.45 0.90 18 0.42 14.23 10.85 1.50 17 2.25 22.78 10.25 2.10 17 1.65 19.38 9.65 2.70 17 1.05 17.17 9.05 3.30 17 0.45 15.66 8.45 3.90 16 2.28 14.62 7.85 4.50 16 1.68 6.96
34 11.81 11.81 0.54 19 0.11 17.01 11.21 1.14 18 0.18 25.78 10.61 1.74 17 2.01 21.22 10.01 2.34 17 1.41 18.38 9.41 2.94 17 0.81 16.49 8.81 3.54 17 0.21 15.20 8.21 4.14 16 2.03 7.15
35 12.17 12.17 0.18 20 0.17 24.87 11.57 0.78 18 0.54 30.02 10.97 1.38 17 2.36 23.65 10.37 1.98 17 1.76 19.92 9.77 2.58 17 1.16 17.53 9.17 3.18 17 0.56 15.91 8.57 3.78 16 2.39 7.40
36 12.53 - - - - - 11.93 0.42 19 0.23 36.41 11.33 1.03 18 0.29 26.98 10.73 1.63 17 2.12 21.93 10.13 2.23 17 1.52 18.84 9.53 2.83 17 0.92 16.80 8.93 3.43 17 0.32 7.71
37 - - - - - - 12.28 0.07 20 0.28 62.51 11.68 0.67 18 0.65 31.78 11.08 1.27 18 0.05 24.61 10.48 1.87 17 1.88 20.51 9.88 2.47 17 1.28 17.92 9.28 3.07 17 0.68 8.09
38 - - - - - - - - - - - 12.04 0.31 20 0.04 40.80 11.44 0.91 18 0.41 28.33 10.84 1.51 17 2.24 22.71 10.24 2.11 17 1.64 19.33 9.64 2.71 17 1.04 8.57
39 - - - - - - - - - - - - - - - - 11.80 0.55 19 0.10 33.82 11.20 1.15 18 0.17 25.67 10.60 1.75 17 2.00 21.16 10.00 2.35 17 1.40 9.17
40 - - - - - - - - - - - - - - - - 12.16 0.19 20 0.16 48.82 11.56 0.79 18 0.52 29.87 10.96 1.39 17 2.35 23.57 10.36 1.99 17 1.75 9.93
41 - - - - - - - - - - - - - - - - - - - - - 11.91 0.44 19 0.21 36.18 11.31 1.04 18 0.28 26.87 10.71 1.64 17 2.11 10.93
42 - - - - - - - - - - - - - - - - - - - - - 12.27 0.08 20 0.27 61.04 11.67 0.68 18 0.64 31.61 11.07 1.28 18 0.04 12.26
43 - - - - - - - - - - - - - - - - - - - - - - - - - - 12.03 0.32 20 0.03 40.20 11.43 0.92 18 0.40 14.10
44 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 11.79 0.56 19 0.09 16.81
45 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 12.15 0.20 20 0.15 23.97
Effective Width Calculation
the calculation of effective live load and position is calculated as per IRC 112-2011

Effective Span of Section = 12.35 Load increment = 0.87333 span 1 span 2 span 3 span 4 span 5
Width of Box nos = 16
Outer Span 12.35 1 = 1.296 12.35 1 0.35 0 0 0 0
Inner Span 0.1 0 12.35 0 0 0 0 2 0.3 0.3 0.3 0.3 0.3
As per Annexure B-3 of IRC-112-2011 6.175 3 0.668 0.668 0.668 0.668 0.668
A
12.35 4 2.4285 -0.55 -0.547 -0.55 2.4285
beff = αa(1-a/l0)+bt 12.35 5 2.4285 -0.55 -0.547 -0.55 2.4285
B
12.35 6 2.4285 -0.55 -0.547 -0.55 2.4285
Where 12.35 7 2.4285 -0.55 -0.547 -0.55 2.4285
C
a= Distance of CG of concentrated Load from nearer Support 12.35 8 0.668 0.668 0.668 0.668 0.668
bt= Breadth of Concentrated area of load 0.98 12.35 9 0.3 0.3 0.3 0.3 0.3
D
α= ratio of b/l0 2.644 12.35 10 0.35 0.35 0.35 0.35 0.35
12.35 12.35 0.1 0.1 0.1 12
E
Impact Factor = 1.25 12.35
Effective Span = 12.35

load loading P1 P2 P3 P4 P5 P6 P7 P8
case postion 68 68 68 68 114 114 27 27
positio a member position load/m positio a membe positio load/m positio a membe positio load/m positio a membe positio load/m positio a membe positio load/m position a membe positio load/m positio a membe positio load/m positio a memb positi load/
n no n r no n n r no n n r no n n r no n r no n n r no n n er no on m
0 -3.00 -6.00 -9.00 -13.30 -14.50 -17.70 -18.80
1 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
2 0.87 0.87 0.87 13 0.22 17.26 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
3 1.75 1.75 1.75 14 0.43 12.60 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
4 2.62 2.62 2.62 14 1.30 10.32 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
5 3.49 3.49 3.49 14 2.18 9.04 0.49 0.49 12 0.14 21.08 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
6 4.37 4.37 4.37 15 0.62 8.30 1.37 1.37 14 0.05 14.18 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
7 5.24 5.24 5.24 15 1.49 7.90 2.24 2.24 14 0.92 11.14 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
8 6.11 6.11 6.11 15 2.37 7.77 3.11 3.11 14 1.80 9.51 0.11 0.11 11 0.11 33.28 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
9 6.99 6.99 5.36 16 0.81 7.87 3.99 3.99 15 0.24 8.57 0.99 0.99 13 0.34 16.41 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
10 7.86 7.86 4.49 16 1.69 8.23 4.86 4.86 15 1.11 8.04 1.86 1.86 14 0.54 12.22 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
11 8.73 8.73 3.62 17 0.13 8.91 5.73 5.73 15 1.99 7.80 2.73 2.73 14 1.42 10.11 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
12 9.61 9.61 2.74 17 1.00 10.09 6.61 5.74 16 0.43 7.80 3.61 3.61 14 2.29 8.92 0.61 0.61 12 0.26 19.74 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
13 10.48 10.48 1.87 17 1.88 12.19 7.48 4.87 16 1.31 8.04 4.48 4.48 15 0.73 8.23 1.48 1.48 14 0.16 13.66 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
14 11.35 11.35 1.00 18 0.32 16.34 8.35 4.00 16 2.18 8.56 5.35 5.35 15 1.61 7.87 2.35 2.35 14 1.04 10.88 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
15 12.23 12.23 0.12 20 0.23 32.62 9.23 3.12 17 0.62 9.50 6.23 6.12 16 0.05 7.77 3.23 3.23 14 1.91 9.36 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
16 13.10 - - - - - 10.10 2.25 17 1.50 11.12 7.10 5.25 16 0.93 7.90 4.10 4.10 15 0.35 8.48 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
17 - - - - - - 10.97 1.38 17 2.37 14.13 7.97 4.38 16 1.80 8.29 4.97 4.97 15 1.23 7.99 0.67 0.67 13 0.02 31.93 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
18 - - - - - - 11.85 0.50 19 0.15 20.95 8.85 3.50 17 0.24 9.03 5.85 5.85 15 2.10 7.78 1.55 1.55 14 0.23 22.42 0.35 0.35 11 0.35 38.82 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
19 - - - - - - - - - - - 9.72 2.63 17 1.12 10.30 6.72 5.63 16 0.55 7.81 2.42 2.42 14 1.10 17.98 1.22 1.22 13 0.57 25.06 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
20 - - - - - - - - - - - 10.59 1.76 17 1.99 12.57 7.59 4.76 16 1.42 8.09 3.29 3.29 14 1.98 15.55 2.09 2.09 14 0.78 19.32 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
21 - - - - - - - - - - - 11.47 0.88 18 0.43 17.18 8.47 3.88 16 2.29 8.66 4.17 4.17 15 0.42 14.14 2.97 2.97 14 1.65 16.31 0.00 0.00 11 0.00 0.00 0.00 0.00 11 0.00 0.00
22 - - - - - - - - - - - 12.34 0.01 120 0.04 42.23 9.34 3.01 17 0.74 9.66 5.04 5.04 15 1.29 13.36 3.84 3.84 15 0.09 14.58 0.64 0.64 12 0.29 7.70 0.00 0.00 11 0.00 0.00
23 - - - - - - - - - - - - - - - - 10.21 2.14 17 1.61 11.41 5.91 5.91 15 2.17 13.04 4.71 4.71 15 0.97 13.59 1.51 1.51 14 0.20 5.37 0.41 0.41 12 0.06 8.80
24 - - - - - - - - - - - - - - - - 11.09 1.26 18 0.05 14.71 6.79 5.56 16 0.61 13.12 5.59 5.59 15 1.84 13.11 2.39 2.39 14 1.07 4.29 1.29 1.29 13 0.64 5.79
25 - - - - - - - - - - - - - - - - 11.96 0.39 19 0.26 22.50 7.66 4.69 16 1.49 13.61 6.46 5.89 16 0.29 13.04 3.26 3.26 14 1.94 3.70 2.16 2.16 14 0.84 4.51
26 - - - - - - - - - - - - - - - - - - - - - 8.53 3.82 16 2.36 14.61 7.33 5.02 16 1.16 13.37 4.13 4.13 15 0.39 3.36 3.03 3.03 14 1.72 3.82
27 - - - - - - - - - - - - - - - - - - - - - 9.41 2.94 17 0.80 16.37 8.21 4.14 16 2.03 14.17 5.01 5.01 15 1.26 3.17 3.91 3.91 15 0.16 3.43
28 - - - - - - - - - - - - - - - - - - - - - 10.28 2.07 17 1.68 19.43 9.08 3.27 17 0.48 15.60 5.88 5.88 15 2.13 3.09 4.78 4.78 15 1.03 3.21
29 - - - - - - - - - - - - - - - - - - - - - 11.15 1.20 18 0.12 25.28 9.95 2.40 17 1.35 18.07 6.75 5.60 16 0.58 3.10 5.65 5.65 15 1.91 3.10
30 - - - - - - - - - - - - - - - - - - - - - 12.03 0.32 20 0.03 39.45 10.83 1.52 17 2.22 22.58 7.63 4.72 16 1.45 3.22 6.53 5.82 16 0.35 3.09
31 - - - - - - - - - - - - - - - - - - - - - - - - - - 11.70 0.65 19 0.00 32.33 8.50 3.85 16 2.33 3.45 7.40 4.95 16 1.23 3.18
32 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 9.37 2.98 17 0.77 3.86 8.27 4.08 16 2.10 3.38
33 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 10.25 2.10 17 1.64 4.56 9.15 3.20 17 0.54 3.73
34 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 11.12 1.23 18 0.09 5.91 10.02 2.33 17 1.42 4.34
35 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 11.99 0.36 19 0.29 9.13 10.89 1.46 17 2.29 5.46
36 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 11.77 0.58 19 0.07 7.94
37 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
38 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
39 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
40 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
 *********************ULS CASE********************

TOP SLAB
HAUNCH START FACE 1 HAUNCH END FACE 1 At d FROM HAUNCH 1 SPAN
LOCATION
SHEAR
246.45 235.57 218.12 117.84
FORCE
HOGGING
99.73 0.96 179.56 0
MOMENT
SAGGING
0 0 109.1 113.95
MOMNET
AXIAL FORCE 190.7 190.7 190.7 190.7

BOTTOM SLAB
HAUNCH START FACE 1 HAUNCH END FACE 1 At d FROM HAUNCH 1 SPAN
LOCATION
SHEAR
380.04 342.04 269.34 142.55
FORCE
HOGGING
0 22.76 504.5 583.19
MOMENT
SAGGING
748.34 528.96 343.4 362.38
MOMNET
AXIAL FORCE 434.13 434.13 434.13 434.13

OUTER WALL SLAB

HAUNCH START FACE 1 HAUNCH END FACE 1 At d FROM HAUNCH 1 SPAN At d FROM HAUNCH 2 HAUNCH END FACE 2 HAUNCH START FACE 2
LOCATION
SHEAR
182.56 174.12 107.74 99.99 167.5 330 374.98
FORCE
HOGGING
471.48 443.46 360.19 311.84 364.86 540.38 625.18
MOMENT
SAGGING
512.07 471.48 443.46 330.61 311.84 364.86 510.38
MOMNET
AXIAL FORCE 270.95 279.55 308.61 337.44 351.85 366.26 395.32

INNER SLAB
HAUNCH START FACE 1 HAUNCH END FACE 1 At d FROM HAUNCH 1 SPAN At d FROM HAUNCH 2 HAUNCH END FACE 2 HAUNCH START FACE 2
LOCATION
SHEAR
0 0 0 0 0 0 0
FORCE
HOGGING
0 0 0 0 0 0 0
MOMENT
SAGGING
0 0 0 0 0 0 0
MOMNET
AXIAL FORCE 0 0 0 0 0 0 0
 *********************SERVICILIBITY********************

TOP SLAB
HAUNCH START FACE 1 HAUNCH END FACE 1 At d FROM HAUNCH 1 SPAN
LOCATION
SHEAR
169.13 161.2 129.22 82.29
FORCE
HOGGING
349.36 302.46 351.6 0
MOMENT
SAGGING
0 0 213.22 415.58
MOMNET
AXIAL FORCE 504.96 504.96 504.96 504.96

BOTTOM SLAB
HAUNCH START FACE 1 HAUNCH END FACE 1 At d FROM HAUNCH 1 SPAN
LOCATION
SHEAR
266.61 250.31 232.95 92.98
FORCE
HOGGING
0 0 169.52 117.91
MOMENT
SAGGING
198.15 0 0 129.83
MOMNET
AXIAL FORCE 327.12 327.12 327.12 327.12

OUTER WALL SLAB

HAUNCH START FACE 1 HAUNCH END FACE 1 At d FROM HAUNCH 1 SPAN At d FROM HAUNCH 2 HAUNCH END FACE 2 HAUNCH START FACE 2
LOCATION
SHEAR
124.95 119.33 75.08 105.43 150.43 258.77 288.75
FORCE
HOGGING
0 0 0 0 0 0 0
MOMENT
SAGGING
351.6 311.32 283.52 172.29 158.65 219.49 408.96
MOMNET
AXIAL FORCE 191.52 197.89 219.42 240.77 251.44 262.12 283.64

INNER SLAB
HAUNCH START FACE 1 HAUNCH END FACE 1 At d FROM HAUNCH 1 SPAN At d FROM HAUNCH 2 HAUNCH END FACE 2 HAUNCH START FACE 2
LOCATION
SHEAR
0 0 0 0 0 0 0
FORCE
HOGGING
0 0 0 0 0 0 0
MOMENT
SAGGING
0 0 0 0 0 0 0
MOMNET
AXIAL FORCE 0 0 0 0 0 0 0
 *********************SLS CHECK********************

TOP SLAB
HAUNCH START FACE 1 HAUNCH END FACE 1 At d FROM HAUNCH 1 SPAN
LOCATION
SHEAR
114.78 106.85 93.54 46.61
FORCE
HOGGING
165.62 132.57 125.7 0
MOMENT
SAGGING
0 0 0 0
MOMNET
AXIAL FORCE 222.92 222.92 222.92 222.92

BOTTOM SLAB
HAUNCH START FACE 1 HAUNCH END FACE 1 At d FROM HAUNCH 1 SPAN
LOCATION
SHEAR
224.92 207.12 182.15 62.88
FORCE
HOGGING
0 -95.81 286.92 330.71
MOMENT
SAGGING
406.32 326.71 264.94 138.71
MOMNET
AXIAL FORCE 247.74 247.74 247.74 247.74

OUTER WALL SLAB

HAUNCH START FACE 1 HAUNCH END FACE 1 At d FROM HAUNCH 1 SPAN At d FROM HAUNCH 2 HAUNCH END FACE 2 HAUNCH START FACE 2
LOCATION
SHEAR
79.71 77.64 74.9 49.13 88.28 184.8 211.9
FORCE
HOGGING
157.06 140.17 102.65 116.68 149.03 271.12 316.11
MOMENT
SAGGING
184.63 188.74 161.16 106.78 116.68 149.03 271.12
MOMNET
AXIAL FORCE 132.12 138.5 160.02 181.37 192.05 202.72 224.25

INNER SLAB
HAUNCH START FACE 1 HAUNCH END FACE 1 At d FROM HAUNCH 1 SPAN At d FROM HAUNCH 2 HAUNCH END FACE 2 HAUNCH START FACE 2
LOCATION
SHEAR
0 0 0 0 0 0 0
FORCE
HOGGING
0 0 0 0 0 0 0
MOMENT
SAGGING
0 0 0 0 0 0 0
MOMNET
AXIAL FORCE 0 0 0 0 0 0 0
 *********************DEFLECTION CHECK********************

TOP SLAB
HAUNCH START FACE 1 HAUNCH END FACE 1 At d FROM HAUNCH 1 SPAN
LOCATION
SHEAR
0 0 0 1.36
FORCE
HOGGING
0 0 0 0
MOMENT
SAGGING
0 0 0 37.77
MOMNET
AXIAL FORCE 93.06 479.66 479.66 479.66

BOTTOM SLAB
HAUNCH START FACE 1 HAUNCH END FACE 1 At d FROM HAUNCH 1 SPAN
LOCATION
SHEAR
232.02 220.75 206.44 108.67
FORCE
HOGGING
0 0 0 0
MOMENT
SAGGING
0 0 0 0
MOMNET
AXIAL FORCE 0 258.19 258.19 258.19

OUTER WALL SLAB

HAUNCH START FACE 1 HAUNCH END FACE 1 At d FROM HAUNCH 1 SPAN At d FROM HAUNCH 2 HAUNCH END FACE 2 HAUNCH START FACE 2
LOCATION
SHEAR
93.06 90.99 88.25 60.68 99.83 196.36 223.46
FORCE
HOGGING
266.38 234.13 207.23 117.09 130.94 161.43 301.68
MOMENT
SAGGING
0 266.38 234.13 126.35 117.09 130.94 161.43
MOMNET
AXIAL FORCE 0 161.89 168.26 200.46 211.14 221.81 232.49

INNER SLAB
HAUNCH START FACE 1 HAUNCH END FACE 1 At d FROM HAUNCH 1 SPAN At d FROM HAUNCH 2 HAUNCH END FACE 2 HAUNCH START FACE 2
LOCATION
SHEAR
0 0 0 0 0 0 0
FORCE
HOGGING
0 0 0 0 0 0 0
MOMENT
SAGGING
0 0 0 0 0 0 0
MOMNET
AXIAL FORCE 0 0 0 0 0 0 0
DESIGN OF RECTANGULAR BEAM / SLAB AS PER IRC : 112 - 2011

Top Slab
At deff from
Type Haunch Face Start Haunch Face End Span
Haunch End
Type of element ( B for Beam & S for Slab ) Reference Unit S S S S
Location Top Top Top Top

Load Data
Moment From Staad output kN-m 99.73 0.96 179.56 0.00
Shear From Staad output kN 246.45 212.01 218.12 117.84
Axial force From Staad output kN 190.70 190.70 190.70 190.70

Material Data
Grade of Steel Fe 500 Fe 500 Fe 500 Fe 500
Charecteristic strength of reinforcement ( fyk ) Table 18.1, IRC 112 MPa 500 500 500 500
partial factor for steel ( gs ) Cl 6.2.2, IRC 112 1.15 1.15 1.15 1.15
Design value for tensile strength ( fyd = fyk/gs ) Cl 6.2.2, IRC 112 MPa 435 435 435 435
Modulus of Elasticity of Steel ( Es ) Cl 6.2.2, IRC 112 GPa 200 200 200 200
Grade of Concrete M 35 M 35 M 35 M 35
Charecteristics compressive strength ( fck ) Table 6.5, IRC 112 MPa 35 35 35 35
a Cl 6.4.2.8, IRC 112 0.67 0.67 0.67 0.67
Concrete material factor ( gm ) Cl 6.4.2.8, IRC 112 1.5 1.5 1.5 1.5
Design value for concrete compressive strength ( f cd = afck/gm ) Cl 6.4.2.8, IRC 112 MPa 15.63 15.63 15.63 15.63

Geometric Data
Width of Slab / Beam ( b ) mm 1000 1000 1000 1000
Total Depth of Slab/Beam ( D ) mm 900 700 700 700
Cover to Reinforcement ( c ) mm 45 45 45 45
Dia of Reinforcement ( f ) mm 16 16 16 16
Spacing of Reinforcement ( s ) or mm 170 170 170 170
Number of Bar ( n ) Nos 0 0 0 0
Area of Reinforcement ( At ) mm2 3031 3031 3031 1183
Reinforcement ( % ) 0.337 0.433 0.433 0.169

Dia of Shear Reinforcement ( f ) mm 0 0 0 0

Spacing of Reinforcement ( s ) or mm 170 170 170 340
Number of legs 2.9 2.9 2.9 3
Shear Reinforcement ( % ) 0.000 0.000 0.000 0.000

Strenght of the section

Moment Resistance
Effective depth of section ( d = D - c - f/2 ) mm 847 647 647 647
Depth of neutral axis from compression flange ( x ) mm 105 105 105 41
l Eq A2-33 & 34, IRC 112 0.8 0.8 0.8 0.8
h Eq A2-35 & 36, IRC 112 1 1 1 1
Depth of stress block ( lx ) mm 84 84 84 33
Stress on stress block ( hfcd ) MPa 15.63 15.63 15.63 15.63
Total Compression Force ( Fc = lx hfcd b) kN 1318 1318 1318 514
Total Tension Force ( Fs = fyd At or fs At) kN 1318 1318 1318 514
Diff ( Fc - Fs ) kN 0 0 0 0
Depth of lever arm ( z = d - lx/2) mm 805 605 605 631
Moment of Resistance ( Fc z ) kN-m 1061 797 797 324
Usage 9.4% 0.1% 22.5% 0.0%
Status OK OK OK OK
Max Strain on concrete in compression ( e cu3 ) Table 6.5, IRC 112 0.0035 0.0035 1.0035 0.0035
Max Strain on reinforcement in tension ( e s = ecu3*(d-x)/x ) 0.0246 0.0180 5.1588 0.0516
Stress in Reinforcement ( fs ) MPa 435 435 435 435
Status Under Reinf Under Reinf Under Reinf Under Reinf
2
Min Reinf As min = 0.26fctm/fyk btd or 0.0013btd Eq 16.1, IRC 112 mm 1101 841 841 841
fctm = Table 6.5, IRC 112 MPa 2.5 2.5 2.5 2.5
Status OK OK OK OK

Members not requiring Design shear reinforcement

Concrete Shear capacity VRd.c = [ 0.12K(80r1.fck)0.33+0.15scp]bd Cl 10.3.2, IRC 112 kN 352 311 311 235
Min Conc Shear capacity nRd.c min = (nmin+0.15scp)bd Cl 10.3.2, IRC 112 kN 308 257 257 257
K = 1+sqrt(200/d) <=2 Eq 10.2, IRC 112 1.486 1.556 1.556 1.556
nmin = 0.031K1.5fck0.5 Eq 10.3, IRC 112 0.332 0.356 0.356 0.356
scp = MPa 0.21 0.27 0.27 0.27
r1 = At /bd <= 0.02 0.004 0.005 0.005 0.002
Check at '0.5d'
β = 0.500 1.000 1.000 1.000
Shear at '0.5d' Cl 10.3.2 (5),IRC 112 kN 232 212.013 218.120 118
Status Reinf not Reqd Reinf not Reqd Reinf not Reqd
Check at '2d'
β = 1.00
Shear at '2d' Cl 10.3.2 (5),IRC 112 218
Status Reinf not Reqd
Distribution Reinforcement (Clause:16.6.1.1-IRC:112-2011)

Minimum Distribution Reinforcement (20% of Main Reinf.) mm2 606 606 606 237
Dia of Reinforcement ( f ) mm 12 12 12 12
Spacing of Reinforcement ( s ) or mm 140 140 140 140
Reinforcement Provided mm2 808 808 808 808
Status OK OK OK OK
DESIGN OF RECTANGULAR BEAM / SLAB AS PER IRC : 112 - 2011

Top Slab

Top Slab
At deff from
Type Haunch Face Start Haunch Face End Span
Haunch End
Type of element ( B for Beam & S for Slab ) S S S S
Location Bottom Bottom Bottom Bottom

Load Data
Moment 0.00 0.00 109.10 113.95
Shear 246.45 212.01 218.12 117.84
Axial force 190.70 190.70 190.70 190.70

Material Data
Grade of Steel Fe 500 Fe 500 Fe 500 Fe 500
Charecteristic strength of reinforcement ( fyk ) 500 500 500 500
partial factor for steel ( gs ) 1.15 1.15 1.15 1.15
Design value for tensile strength ( fyd = fyk/gs ) 435 435 435 435
Modulus of Elasticity of Steel ( Es ) 200 200 200 200
Grade of Concrete M 35 M 35 M 35 M 35
Charecteristics compressive strength ( fck ) 35 35 35 35
a 0.67 0.67 0.67 0.67
Concrete material factor ( gm ) 1.5 1.5 1.5 1.5
Design value for concrete compressive strength ( f cd = afck/gm ) 15.63 15.63 15.63 15.63

Geometric Data
Width of Slab / Beam ( b ) 1000 1000 1000 1000
Total Depth of Slab/Beam ( D ) 900 700 700 700
Cover to Reinforcement ( c ) 45 45 45 45
Dia of Reinforcement ( f ) 20 20 20 20
Spacing of Reinforcement ( s ) or 170 170 170 170
Number of Bar ( n ) 0 0 0 0
Area of Reinforcement ( At ) 1848 1848 1848 1848
Reinforcement ( % ) 0.205 0.264 0.264 0.264

Dia of Shear Reinforcement ( f ) 0 0 0 0

Spacing of Reinforcement ( s ) or 170 170 170 340
Number of legs 2.9 2.9 4.0 2.9
Shear Reinforcement ( % ) 0.000 0.000 0.000 0.000

Strenght of the section

Moment Resistance
Effective depth of section ( d = D - c - f/2 ) 845 645 645 645
Depth of neutral axis from compression flange ( x ) 64 64 64 64
l 0.8 0.8 0.8 0.8
h 1 1 1 1
Depth of stress block ( lx ) 51 51 51 51
Stress on stress block ( hfcd ) 15.63 15.63 15.63 15.63
Total Compression Force ( Fc = lx hfcd b) 803 803 803 803
Total Tension Force ( Fs = fyd At or fs At) 803 803 803 803
Diff ( Fc - Fs ) 0 0 0 0
Depth of lever arm ( z = d - lx/2) 819 619 619 619
Moment of Resistance ( Fc z ) 658 498 498 498
Usage 0.0% 0.0% 21.9% 22.9%
Status OK OK OK OK
Max Strain on concrete in compression ( e cu3 ) 0.0035 0.0035 1.0035 0.0035
Max Strain on reinforcement in tension ( e s = ecu3*(d-x)/x ) 0.0425 0.0316 9.0715 0.0316
Stress in Reinforcement ( fs ) 435 435 435 435
Status Under Reinf Under Reinf Under Reinf Under Reinf
Min Reinf As min = 0.26fctm/fyk btd or 0.0013btd 1099 839 839 839
fctm = 2.5 2.5 2.5 2.5
Status OK OK OK OK

Members not requiring Design shear reinforcement

Concrete Shear capacity VRd.c = [ 0.12K(80r1.fck)0.33+0.15scp]bd 276 241 241 241
Min Conc Shear capacity nRd.c min = (nmin+0.15scp)bd 281 230 230 230
K = 1+sqrt(200/d) <=2 1.487 1.557 1.557 1.557
nmin = 0.031K1.5fck0.5 0.332 0.356 0.356 0.356
scp = 0.00 0.00 0.00 0.00
r1 = At /bd <= 0.02 0.002 0.003 0.003 0.003
Check at '0.5d'
β = 1.000 1.000 1.000 1.000
Shear at '0.5d' 246 212 118
Status Reinf not Reqd Reinf not Reqd Reinf not Reqd
Check at '2d'
β = 1.00
Shear at '2d' 218
Status Reinf not Reqd
Distribution Reinforcement

Minimum Distribution Reinforcement (20% of Main Reinf.) 370 370 370 370
Dia of Shear Reinforcement ( f ) 12 12 12 12
Spacing of Reinforcement ( s ) or 140 140 140 140
Reinforcement Provided 808 808 808 808
Status OK OK OK OK
DESIGN OF RECTANGULAR BEAM / SLAB AS PER IRC : 112 - 2011
Sections
Outer Wall
Top Haunch Top Haunch At deff from At deff from Bot Haunch Bot Haunch
Type Centre
Face Start Face End Haunch End Haunch End Face Start Face End
Type of element ( B for Beam & S for Slab ) Reference Unit S S S S S S S
Location Outer Outer Outer Outer Outer Outer Outer

Load Data
Moment From Staad output kN-m 471.48 443.46 360.19 311.84 364.86 540.38 500.14
Shear From Staad output kN 182.56 174.12 107.74 99.99 167.50 330.00 374.98
Axial force From Staad output kN 270.95 279.55 308.61 337.44 351.85 366.26 395.32

Material Data
Grade of Steel Fe 500 Fe 500 Fe 500 Fe 500 Fe 500 Fe 500 Fe 500
Charecteristic strength of reinforcement ( fyk ) Table 18.1, IRC 112 MPa 500 500 500 500 500 500 500
partial factor for steel ( gs ) Cl 6.2.2, IRC 112 1.15 1.15 1.15 1.15 1.15 1.15 1.15
Design value for tensile strength ( fyd = fyk/gs ) Cl 6.2.2, IRC 112 MPa 435 435 435 435 435 435 435
Modulus of Elasticity of Steel ( Es ) Cl 6.2.2, IRC 112 GPa 200 200 200 200 200 200 200
Grade of Concrete M 35 M 35 M 35 M 35 M 35 M 35 M 35
Charecteristics compressive strength ( fck ) Table 6.5, IRC 112 MPa 35 35 35 35 35 35 35
a Cl 6.4.2.8, IRC 112 0.67 0.67 0.67 0.67 0.67 0.67 0.67
Concrete material factor ( g m ) Cl 6.4.2.8, IRC 112 1.5 1.5 1.5 1.5 1.5 1.5 1.5
Design value for concrete compressive strength ( fcd = afck/gm ) Cl 6.4.2.8, IRC 112 MPa 15.63 15.63 15.63 15.63 15.63 15.63 15.63

Geometric Data
Width of Slab / Beam ( b ) mm 1000 1000 1000 1000 1000 1000 1000
Total Depth of Slab/Beam ( D ) mm 900 700 700 700 700 900 700
Cover to Reinforcement ( c ) mm 75 75 75 75 75 75 75
Dia of Reinforcement ( f ) mm 20 20 20 20 20 20 20
Spacing of Reinforcement ( s ) or mm 170 170 170 170 170 170 170
Number of Bar ( n ) Nos 0 0 0 0 0 0 0
Area of Reinforcement ( At ) mm2 3031 3031 3031 1848 3696 3696 3696
Reinforcement ( % ) 0.337 0.433 0.433 0.264 0.528 0.411 0.528

Dia of Shear Reinforcement ( f ) mm 0 0 0 0 0 0 0

Spacing of Reinforcement ( s ) or mm 340 340 340 340 340 170 170
Number of legs 3 3 3 3 3 2 2
Shear Reinforcement ( % ) 0.000 0.000 0.000 0.000 0.000 0.000 0.000

Strenght of the section

Moment Resistance
Effective depth of section ( d = D - c - f/2 ) mm 815 615 615 615 615 815 615
Depth of neutral axis from compression flange ( x ) mm 105 105 105 64 128 128 128
l Eq A2-33 & 34, IRC 112 0.8 0.8 0.8 0.8 0.8 0.8 0.8
h Eq A2-35 & 36, IRC 112 1 1 1 1 1 1 1
Depth of stress block ( lx ) mm 84 84 84 51 103 103 103
Stress on stress block ( hfcd ) MPa 15.63 15.63 15.63 15.63 15.63 15.63 15.63
Total Compression Force ( Fc = lx hfcd b) kN 1318 1318 1318 803 1607 1607 1607
Total Tension Force ( Fs = fyd At or fs At) kN 1318 1318 1318 803 1607 1607 1607
Diff ( Fc - Fs ) kN 0 0 0 0 0 0 0
Depth of lever arm ( z = d - lx/2) mm 773 573 573 589 564 764 564
Moment of Resistance ( Fc z ) kN-m 1018 755 755 473 906 1227 906
Usage 46.3% 58.7% 47.7% 65.9% 40.3% 44.0% 55.2%
Status OK OK OK OK OK OK OK
Max Strain on concrete in compression ( e cu3 ) Table 6.5, IRC 112 0.0035 0.0035 0.0035 0.0035 0.0035 0.0035 0.0035
Max Strain on reinforcement in tension ( e s = ecu3*(d-x)/x ) 0.0236 0.0169 0.0169 0.0300 0.0133 0.0187 0.0133
Stress in Reinforcement ( fs ) MPa 435 435 435 435 435 435 435
Status Under Reinf Under Reinf Under Reinf Under Reinf Under Reinf Under Reinf Under Reinf
2
Min Reinf As min = 0.26fctm/fyk btd or 0.0013btd Eq 16.1, IRC 112 mm 1060 800 800 800 800 1060 800
fctm = Table 6.5, IRC 112 MPa 2.5 2.5 2.5 2.5 2.5 2.5 2.5
Status OK OK OK OK OK OK OK

Members not requiring Design shear reinforcement

Concrete Shear capacity VRd.c = [ 0.12K(80r1.fck)0.33+0.15scp]bd Cl 10.3.2, IRC 112 kN 356 315 318 280 343 391 349
Min Conc Shear capacity nRd.c min = (nmin+0.15scp)bd Cl 10.3.2, IRC 112 kN 310 259 263 266 268 323 274
K = 1+sqrt(200/d) <=2 Eq 10.2, IRC 112 1.495 1.570 1.570 1.570 1.570 1.495 1.570
nmin = 0.031K1.5fck0.5 Eq 10.3, IRC 112 0.335 0.361 0.361 0.361 0.361 0.335 0.361
scp = MPa 0.30 0.40 0.44 0.48 0.50 0.41 0.56
r1 = At /bd <= 0.02 0.004 0.005 0.005 0.003 0.006 0.005 0.006
Check at '0.5d'
β = 1.000 1.000 1.000 1.000 1.000 1.000 0.500
Shear at '0.5d' Cl 10.3.2 (5),IRC 112 kN 183 174 100 271 271
Status Reinf not Reqd Reinf not Reqd Reinf not Reqd Reinf not Reqd Reinf not Reqd
Check at '2d'
β = 1.00 1.00
Shear at '2d' Cl 10.3.2 (5),IRC 112 108 168
Status Reinf not Reqd Reinf not Reqd
Distribution Reinforcement (Clause:16.6.1.1-IRC:112-2011)

Minimum Distribution Reinforcement (20% of Main Reinf.) mm2 606 606 606 370 739 739 739
Dia of Reinforcement ( f ) mm 12 12 12 12 12 12 12
Spacing of Reinforcement ( s ) or mm 140 140 140 140 140 140 140
Reinforcement Provided mm2 808 808 808 808 808 808 808
Status OK OK OK OK OK OK OK
DESIGN OF RECTANGULAR BEAM / SLAB AS PER IRC : 112 - 2011
Sections
Outer Wall
Type
Outer Wall
Top Haunch Top Haunch At deff from At deff from Bot Haunch Bot Haunch
Type Centre
Face Start Face End Haunch End Haunch End Face Start Face End
Type of element ( B for Beam & S for Slab ) S S S S S S S
Location Inner Inner Inner Inner Inner Inner Inner

Load Data
Moment 512.07 471.48 443.46 330.61 311.84 364.86 510.38
Shear 182.56 174.12 107.74 99.99 167.50 330.00 374.98
Axial force 270.95 279.55 308.61 337.44 351.85 366.26 395.32

Material Data
Grade of Steel Fe 500 Fe 500 Fe 500 Fe 500 Fe 500 Fe 500 Fe 500
Charecteristic strength of reinforcement ( fyk ) 500 500 500 500 500 500 500
partial factor for steel ( gs ) 1.15 1.15 1.15 1.15 1.15 1.15 1.15
Design value for tensile strength ( fyd = fyk/gs ) 435 435 435 435 435 435 435
Modulus of Elasticity of Steel ( Es ) 200 200 200 200 200 200 200
Grade of Concrete M 35 M 35 M 35 M 35 M 35 M 35 M 35
Charecteristics compressive strength ( fck ) 35 35 35 35 35 35 35
a 0.67 0.67 0.67 0.67 0.67 0.67 0.67
Concrete material factor ( g m ) 1.5 1.5 1.5 1.5 1.5 1.5 1.5
Design value for concrete compressive strength ( fcd = afck/gm ) 15.63 15.63 15.63 15.63 15.63 15.63 15.63

Geometric Data
Width of Slab / Beam ( b ) 1000 1000 1000 1000 1000 1000 1000
Total Depth of Slab/Beam ( D ) 900 700 700 700 700 900 700
Cover to Reinforcement ( c ) 45 45 45 45 45 45 45
Dia of Reinforcement ( f ) 25 25 25 25 25 25 25
Spacing of Reinforcement ( s ) or 170 170 170 170 170 170 170
Number of Bar ( n ) 0 0 0 0 0 0 0
Area of Reinforcement ( At ) 2887 2887 2887 2887 2887 2887 2887
Reinforcement ( % ) 0.321 0.412 0.412 0.412 0.412 0.321 0.412

Dia of Shear Reinforcement ( f ) 0 0 0 0 0 0 0

Spacing of Reinforcement ( s ) or 340 340 340 340 340 170 170
Number of legs 3 3 3 3 3 2 2
Shear Reinforcement ( % ) 0.000 0.000 0.000 0.000 0.000 0.000 0.000

Strenght of the section

Moment Resistance
Effective depth of section ( d = D - c - f/2 ) 843 643 643 643 643 843 643
Depth of neutral axis from compression flange ( x ) 100 100 100 100 100 100 100
l 0.8 0.8 0.8 0.8 0.8 0.8 0.8
h 1 1 1 1 1 1 1
Depth of stress block ( lx ) 80 80 80 80 80 80 80
Stress on stress block ( hfcd ) 15.63 15.63 15.63 15.63 15.63 15.63 15.63
Total Compression Force ( Fc = lx hfcd b) 1255 1255 1255 1255 1255 1255 1255
Total Tension Force ( Fs = fyd At or fs At) 1255 1255 1255 1255 1255 1255 1255
Diff ( Fc - Fs ) 0 0 0 0 0 0 0
Depth of lever arm ( z = d - lx/2) 802 602 602 602 602 802 602
Moment of Resistance ( Fc z ) 1007 756 756 756 756 1007 756
Usage 50.8% 62.3% 58.6% 43.7% 41.2% 36.2% 67.5%
Status OK OK OK OK OK OK OK
Max Strain on concrete in compression ( e cu3 ) 0.0035 0.0035 0.0035 0.0035 0.0035 0.0035 0.0035
Max Strain on reinforcement in tension ( e s = ecu3*(d-x)/x ) 0.0259 0.0189 0.0189 0.0189 0.0189 0.0259 0.0189
Stress in Reinforcement ( fs ) 435 435 435 435 435 435 435
Status Under Reinf Under Reinf Under Reinf Under Reinf Under Reinf Under Reinf Under Reinf
Min Reinf As min = 0.26fctm/fyk btd or 0.0013btd 1095 835 835 835 835 1095 835
fctm = 2.5 2.5 2.5 2.5 2.5 2.5 2.5
Status OK OK OK OK OK OK OK

Members not requiring Design shear reinforcement

Concrete Shear capacity VRd.c = [ 0.12K(80r1.fck)0.33+0.15scp]bd 319 279 279 279 279 319 352
Min Conc Shear capacity nRd.c min = (nmin+0.15scp)bd 280 229 229 229 229 280 229
K = 1+sqrt(200/d) <=2 1.487 1.558 1.558 1.558 1.558 1.487 1.558
nmin = 0.031K1.5fck0.5 0.333 0.357 0.357 0.357 0.357 0.333 0.357
scp = 0.00 0.00 0.00 0.00 0.00 0.00 0.00
r1 = At /bd <= 0.02 0.003 0.004 0.004 0.004 0.004 0.003 0.009
Check at '0.5d'
β = 1.000 1.000 1.000 1.000 1.000 1.000 1.000
Shear at '0.5d' 183 174 100 330 375
Status Reinf not Reqd Reinf not Reqd Reinf not Reqd Reinf not Reqd Reinf not Reqd
Check at '2d'
β = 1.00 0.50
Shear at '2d' 108 84
Status Reinf not Reqd Reinf not Reqd
Distribution Reinforcement

Minimum Distribution Reinforcement (20% of Main Reinf.) 577 577 577 577 577 577 577
Dia of Shear Reinforcement ( f ) 12 12 12 12 12 12 12
Spacing of Reinforcement ( s ) or 140 140 140 140 140 140 140
Reinforcement Provided 808 808 808 808 808 808 808
Status OK OK OK OK OK OK OK
DESIGN OF RECTANGULAR BEAM / SLAB AS PER IRC : 112 - 2011
Sections
Bottom Slab
Haunch Face Haunch Face At deff from
Type Span
Start End Haunch End
Type of element ( B for Beam & S for Slab ) Reference Unit S S S S
Location Bottom Bottom Bottom Bottom

Load Data
Moment From Staad output kN-m 748.34 528.96 343.40 362.38
Shear From Staad output kN 380.04 342.04 269.34 142.55
Axial force From Staad output kN 434.13 434.13 434.13 434.13

Material Data
Grade of Steel Fe 500 Fe 500 Fe 500 Fe 500
Charecteristic strength of reinforcement ( fyk ) Table 18.1, IRC 112 MPa 500 500 500 500
partial factor for steel ( gs ) Cl 6.2.2, IRC 112 1.15 1.15 1.15 1.15
Design value for tensile strength ( fyd = fyk/gs ) Cl 6.2.2, IRC 112 MPa 435 435 435 435
Modulus of Elasticity of Steel ( Es ) Cl 6.2.2, IRC 112 GPa 200 200 200 200
Grade of Concrete M 35 M 35 M 35 M 35
Charecteristics compressive strength ( fck ) Table 6.5, IRC 112 MPa 35 35 35 35
a Cl 6.4.2.8, IRC 112 0.67 0.67 0.67 0.67
Concrete material factor ( gm ) Cl 6.4.2.8, IRC 112 1.5 1.5 1.5 1.5
Design value for concrete compressive strength ( f cd = afck/gm ) Cl 6.4.2.8, IRC 112 MPa 15.63 15.63 15.63 15.63

Geometric Data
Width of Slab / Beam ( b ) mm 1000 1000 1000 1000
Total Depth of Slab/Beam ( D ) mm 950 750 750 750
Cover to Reinforcement ( c ) mm 75 75 75 75
Dia of Reinforcement ( f ) mm 20 20 20 20
Spacing of Reinforcement ( s ) or mm 85 85 85 170
Number of Bar ( n ) Nos 0 0 0 0
Area of Reinforcement ( At ) mm2 3696 3696 3696 1848
Reinforcement ( % ) 0.389 0.493 0.493 0.246

Dia of Shear Reinforcement ( f ) mm 0 0 0 0

Spacing of Reinforcement ( s ) or mm 170 170 170 340
Number of legs 5.9 5.9 5.9 2.9
Shear Reinforcement ( % ) 0.000 0.000 0.000 0.000

Strenght of the section

Moment Resistance
Effective depth of section ( d = D - c - f/2 ) mm 865 665 665 665
Depth of neutral axis from compression flange ( x ) mm 128 128 128 64
l Eq A2-33 & 34, IRC 112 0.8 0.8 0.8 0.8
h Eq A2-35 & 36, IRC 112 1 1 1 1
Depth of stress block ( lx ) mm 103 103 103 51
Stress on stress block ( hfcd ) MPa 15.63 15.63 15.63 15.63
Total Compression Force ( Fc = lx hfcd b) kN 1607 1607 1607 803
Total Tension Force ( Fs = fyd At or fs At) kN 1607 1607 1607 803
Diff ( Fc - Fs ) kN 0 0 0 0
Depth of lever arm ( z = d - lx/2) mm 814 614 614 639
Moment of Resistance ( Fc z ) kN-m 1307 986 986 514
Usage 57.2% 53.6% 34.8% 70.5%
Status OK OK OK OK
Max Strain on concrete in compression ( e cu3 ) Table 6.5, IRC 112 0.0035 0.0035 0.0035 0.0035
Max Strain on reinforcement in tension ( e s = ecu3*(d-x)/x ) 0.0201 0.0146 0.0146 0.0327
Stress in Reinforcement ( fs ) MPa 435 435 435 435
Status Under Reinf Under Reinf Under Reinf Under Reinf
2
Min Reinf As min = 0.26fctm/fyk btd or 0.0013btd Eq 16.1, IRC 112 mm 1125 865 865 865
fctm = Table 6.5, IRC 112 MPa 2.5 2.5 2.5 2.5
Status OK OK OK OK

Members not requiring Design shear reinforcement

Concrete Shear capacity VRd.c = [ 0.12K(80r1.fck)0.33+0.15scp]bd Cl 10.3.2, IRC 112 kN 411 366 366 302
Min Conc Shear capacity nRd.c min = (nmin+0.15scp)bd Cl 10.3.2, IRC 112 kN 345 293 293 293
K = 1+sqrt(200/d) <=2 Eq 10.2, IRC 112 1.481 1.548 1.548 1.548
nmin = 0.031K1.5fck0.5 Eq 10.3, IRC 112 0.330 0.353 0.353 0.353
scp = MPa 0.46 0.58 0.58 0.58
r1 = At /bd <= 0.02 0.004 0.006 0.006 0.003
Check at '0.5d'
β = 1.000 1.000 1.000 1.000
Shear at '0.5d' Cl 10.3.2 (5),IRC 112 kN 380 342 143
Status Reinf not Reqd Reinf not Reqd Reinf not Reqd
Check at '2d'
β = 1.00
Shear at '2d' Cl 10.3.2 (5),IRC 112 269
Status Reinf not Reqd
Distribution Reinforcement (Clause:16.6.1.1-IRC:112-2011)

Minimum Distribution Reinforcement (20% of Main Reinf.) mm2 739 739 739 370
Dia of Reinforcement ( f ) mm 12 12 12 12
Spacing of Reinforcement ( s ) or mm 140 140 140 140
Reinforcement Provided mm2 808 808 808 808
Status OK OK OK OK
DESIGN OF RECTANGULAR BEAM / SLAB AS PER IRC : 112 - 2011
Sections
Bottom Slab
Type
Bottom Slab
Haunch Face Haunch Face At deff from
Type Span
Start End Haunch End
Type of element ( B for Beam & S for Slab ) S S S S
Location Top Top Top Top

Load Data
Moment 0.00 22.76 403.60 583.19
Shear 380.04 342.04 269.34 142.55
Axial force 434.13 434.13 434.13 434.13

Material Data
Grade of Steel Fe 500 Fe 500 Fe 500 Fe 500
Charecteristic strength of reinforcement ( fyk ) 500 500 500 500
partial factor for steel ( gs ) 1.15 1.15 1.15 1.15
Design value for tensile strength ( fyd = fyk/gs ) 435 435 435 435
Modulus of Elasticity of Steel ( Es ) 200 200 200 200
Grade of Concrete M 35 M 35 M 35 M 35
Charecteristics compressive strength ( fck ) 35 35 35 35
a 0.67 0.67 0.67 0.67
Concrete material factor ( gm ) 1.5 1.5 1.5 1.5
Design value for concrete compressive strength ( f cd = afck/gm ) 15.63 15.63 15.63 15.63

Geometric Data
Width of Slab / Beam ( b ) 1000 1000 1000 1000
Total Depth of Slab/Beam ( D ) 950 750 750 750
Cover to Reinforcement ( c ) 75 75 75 75
Dia of Reinforcement ( f ) 25 25 25 25
Spacing of Reinforcement ( s ) or 170 170 170 170
Number of Bar ( n ) 0 0 0 0
Area of Reinforcement ( At ) 2887 2887 2887 2887
Reinforcement ( % ) 0.304 0.385 0.385 0.385

Dia of Shear Reinforcement ( f ) 0 0 0 0

Spacing of Reinforcement ( s ) or 170 170 170 340
Number of legs 4.0 4.0 4.0 2.9
Shear Reinforcement ( % ) 0.0000 0.0000 0.0000 0.0000

Strenght of the section

Moment Resistance
Effective depth of section ( d = D - c - f/2 ) 863 663 663 663
Depth of neutral axis from compression flange ( x ) 100 100 100 100
l 0.8 0.8 0.8 0.8
h 1 1 1 1
Depth of stress block ( lx ) 80 80 80 80
Stress on stress block ( hfcd ) 15.63 15.63 15.63 15.63
Total Compression Force ( Fc = lx hfcd b) 1255 1255 1255 1255
Total Tension Force ( Fs = fyd At or fs At) 1255 1255 1255 1255
Diff ( Fc - Fs ) 0 0 0 0
Depth of lever arm ( z = d - lx/2) 822 622 622 622
Moment of Resistance ( Fc z ) 1032 781 781 781
Usage 0.0% 2.9% 51.7% 74.6%
Status OK OK OK OK
Max Strain on concrete in compression ( e cu3 ) 0.0035 0.0035 0.0035 0.0035
Max Strain on reinforcement in tension ( e s = ecu3*(d-x)/x ) 0.0266 0.0196 0.0196 0.0196
Stress in Reinforcement ( fs ) 435 435 435 435
Status Under Reinf Under Reinf Under Reinf Under Reinf
Min Reinf As min = 0.26fctm/fyk btd or 0.0013btd 1121 861 861 861
fctm = 2.5 2.5 2.5 2.5
Status OK OK OK OK

Members not requiring Design shear reinforcement

Concrete Shear capacity VRd.c = [ 0.12K(80r1.fck)0.33+0.15scp]bd 407 283 283 0
Min Conc Shear capacity nRd.c min = (nmin+0.15scp)bd 285 234 234 234
K = 1+sqrt(200/d) <=2 1.482 1.549 1.549 1.549
nmin = 0.031K1.5fck0.5 0.331 0.354 0.354 0.354
scp = 0.00 0.00 0.00 0.00
r1 = At /bd <= 0.02 0.007 0.004 0.004 0.004
Check at '0.5d'
β = 1.000 1.000 1.000 1.000
Shear at '0.5d' 380 342 143
Status Reinf not Reqd Reinf not Reqd Reinf not Reqd
Check at '2d'
β = 1.00
Shear at '2d' 269
Status Reinf not Reqd
Distribution Reinforcement

Minimum Distribution Reinforcement (20% of Main Reinf.) 577 577 577 577
Dia of Shear Reinforcement ( f ) 12 12 12 12
Spacing of Reinforcement ( s ) or 140 140 140 140
Reinforcement Provided 808 808 808 808
Status OK OK OK OK
DESIGN OF RECTANGULAR BEAM / SLAB AS PER IRC : 112 - 2011
Type
Type of element ( B for Beam & S for Slab ) Refereance Unit S S S
Top Slab
Haunch Face At deff from
Span
Load Data End Haunch End
Moment kN-m 302.46 351.60 415.58

Material Data
Grade of Steel Fe 500 Fe 500 Fe 500
Charecteristic strength of reinforcement ( fyk ) Table 18.1, IRC 112 MPa 500 500 500
partial factor for steel ( gs ) Cl 6.2.2, IRC 112 1.15 1.15 1.15
Design value for tensile strength ( fyd = fyk/gs ) Cl 6.2.2, IRC 112 MPa 435 435 435
Modulus of Elasticity of Steel ( Es ) Cl 6.2.2, IRC 112 GPa 200.00 200 200
Grade of Concrete M 35 M 35 M 35
Charecteristics compressive strength ( fck ) Table 6.5, IRC 112 MPa 35 35 35
a Cl 6.4.2.8, IRC 112 0.67 0.67 0.67
Concrete material factor ( gm ) Cl 6.4.2.8, IRC 112 1.50 1.5 1.5
Design value for concrete compressive strength ( fcd = afck/gm ) Cl 6.4.2.8, IRC 112 MPa 15.63 15.63 15.63
Modulus of Elasticity of Concrete ( Ecm ) Table 6.5, IRC 112 GPa 30 30 30

Geometric Data
Width of Slab / Beam ( b ) mm 1000 1000 1000
Total Depth of Beam ( D ) mm 700 700 700
Cover to Reinforcement ( c ) mm 45 45 45
Dia of Reinforcement ( f ) mm 16 16 20
Effective depth of beam / Slab ( d ) mm 647 647 647
Spacing of Reinforcement ( s ) or mm 170 170 170
Number of Bar ( n ) Nos 0 0 0
Area of Reinforcement ( At ) mm2 3031 3031 1848
Reinforcement ( % ) 0.433 0.433 0.264

Stress Check

Concrete Cross Sectional Area ( Ac ) mm 700000 700000 700000

Perimeter in contact with atmosphere ( u ) mm 3400 3400 3400
Notional Size 412 412 412
Effective Modulus of Elasticity of Conc. ( Eeff ) Cl 6.4.2.5, IRC 112 MPa 10777 10777 10777
Modular ratio ( m ) 18.56 18.56 18.56
Allowable stress in steel Cl 12.2.2, IRC 112 MPa 400 400 400
Allowable stress in concrete Cl 12.2.1, IRC 112 MPa 16.80 16.80 16.80
Position of nutural axis from comp face ( x ) mm 219.33 219.33 179.14
MOA of compression area mm2 24053373 24053373 16045157
MOA of tension area mm2 24053373 24053373 16045157
Diff 0 0 0
MOI of cracked section 1.38E+10 1.38E+10 9.42E+09
Final Stress in Top Slab bottom=Const stage
stress+Service stage stress
Stress in tension reinf MPa 174 202 383
Status OK OK OK
Stress in concrete MPa 4.81 5.59 7.90
Status OK OK OK
DESIGN OF RECTANGULAR BEAM / SLAB AS PER IRC : 112 - 2011
Type
Type of element ( B for Beam & S for Slab ) Refereance Unit S S
OUTER WALL
At 2 Deff from At 2 Deff from
Top Centre Bottom
Load Data Haunch End Haunch End
Moment kN-m 0.00 0.00 0.00 0.00 0.00

Material Data
Grade of Steel Fe 500 Fe 500 Fe 500 Fe 500 Fe 500
Charecteristic strength of reinforcement ( fyk ) Table 18.1, IRC 112 MPa 500 500 500 500 500
partial factor for steel ( gs ) Cl 6.2.2, IRC 112 1.15 1.15 1.15 1.15 1.15
Design value for tensile strength ( fyd = fyk/gs ) Cl 6.2.2, IRC 112 MPa 435 435 435 435 435
Modulus of Elasticity of Steel ( Es ) Cl 6.2.2, IRC 112 GPa 200 200 200 200 200
Grade of Concrete M 35 M 35 M 35 M 35 M 35
Charecteristics compressive strength ( fck ) Table 6.5, IRC 112 MPa 35 35 35 35 35
a Cl 6.4.2.8, IRC 112 0.67 0.67 0.67 0.67 0.67
Concrete material factor ( gm ) Cl 6.4.2.8, IRC 112 1.5 1.5 1.5 1.5 1.5
Design value for concrete compressive strength ( fcd = afck/gm ) Cl 6.4.2.8, IRC 112 MPa 15.63 15.63 15.63 15.63 15.63
Modulus of Elasticity of Concrete ( Ecm ) Table 6.5, IRC 112 GPa 30 30 30 30 30

Geometric Data
Width of Slab / Beam ( b ) mm 1000 1000 1000 1000 1000
Total Depth of Beam ( D ) mm 700 700 700 700 700
Cover to Reinforcement ( c ) mm 75 75 75 75 75
Dia of Reinforcement ( f ) mm 20 20 25 20 20
Effective depth of beam / Slab ( d ) mm 615 615 643 615 615
Spacing of Reinforcement ( s ) or mm 170 170 170 170 170
Number of Bar ( n ) Nos 0 0 0 0 0
Area of Reinforcement ( At ) mm2 3031 3031 2887 3696 3696
Reinforcement ( % ) 0.433 0.433 0.412 0.528 0.528

Stress Check

Concrete Cross Sectional Area ( Ac ) mm 700000 700000 700000 700000 700000

Perimeter in contact with atmosphere ( u ) mm 3400 3400 3400 3400 3400
Notional Size 412 412 412 412 412
Effective Modulus of Elasticity of Conc. ( Eeff ) Cl 6.4.2.5, IRC 112 MPa 10777 10777 10777 10777 10777
Modular ratio ( m ) 18.56 18.56 18.56 18.56 18.56
Allowable stress in steel Cl 12.2.2, IRC 112 MPa 400 400 400 400 400
Allowable stress in concrete Cl 12.2.1, IRC 112 MPa 16.80 16.80 16.80 16.80 16.80
Position of nutural axis from comp face ( x ) mm 212.72 212.72 214.24 229.86 229.86
MOA of compression area mm2 22625375 22625375 22948641 26416766 26416766
MOA of tension area mm2 22625375 22625375 22948641 26416766 26416766
Diff 0 0 0 0 0
MOI of cracked section 1.23E+10 1.23E+10 1.31E+10 1.42E+10 1.42E+10

Stress in tension reinf MPa 0 0 0 0 0

Status OK OK OK OK OK
Stress in concrete MPa 0.00 0.00 0.00 0.00 0.00
Status OK OK OK OK OK
DESIGN OF RECTANGULAR BEAM / SLAB AS PER IRC : 112 - 2011
Type
Type of element ( B for Beam & S for Slab ) Refereance Unit
BOTTOM SLAB
At 2 Deff from
Haunch Face Span
Load Data Haunch End
Moment kN-m 0.00 0.00 117.91

Material Data
Grade of Steel Fe 500 Fe 500 Fe 500
Charecteristic strength of reinforcement ( fyk ) Table 18.1, IRC 112 MPa 500 500 500
partial factor for steel ( gs ) Cl 6.2.2, IRC 112 1.15 1.15 1.15
Design value for tensile strength ( fyd = fyk/gs ) Cl 6.2.2, IRC 112 MPa 435 435 435
Modulus of Elasticity of Steel ( Es ) Cl 6.2.2, IRC 112 GPa 200 200 200
Grade of Concrete M 35 M 35 M 35
Charecteristics compressive strength ( fck ) Table 6.5, IRC 112 MPa 35 35 35
a Cl 6.4.2.8, IRC 112 0.67 0.67 0.67
Concrete material factor ( gm ) Cl 6.4.2.8, IRC 112 1.5 1.5 1.5
Design value for concrete compressive strength ( fcd = afck/gm ) Cl 6.4.2.8, IRC 112 MPa 15.63 15.63 15.63
Modulus of Elasticity of Concrete ( Ecm ) Table 6.5, IRC 112 GPa 30 30 30

Geometric Data
Width of Slab / Beam ( b ) mm 1000 1000 1000
Total Depth of Beam ( D ) mm 750 750 750
Cover to Reinforcement ( c ) mm 75 75 75
Dia of Reinforcement ( f ) mm 20 20 25
Effective depth of beam / Slab ( d ) mm 665 665 662.5
Spacing of Reinforcement ( s ) or mm 85 85 170
Number of Bar ( n ) Nos 0 0 0
Area of Reinforcement ( At ) mm2 3695.991357 3695.991357 2887.493248
Reinforcement ( % ) 0.493 0.493 0.385

Stress Check

Concrete Cross Sectional Area ( Ac ) mm 750000 750000 750000

Perimeter in contact with atmosphere ( u ) mm 3500 3500 3500
Notional Size 429 429 429
Effective Modulus of Elasticity of Conc. ( Eeff ) Cl 6.4.2.5, IRC 112 MPa 10806 10806 10806
Modular ratio ( m ) 18.51 18.51 18.51
Allowable stress in steel Cl 12.2.2, IRC 112 MPa 400 400 400
Allowable stress in concrete Cl 12.2.1, IRC 112 MPa 16.80 16.80 16.80
Position of nutural axis from comp face ( x ) mm 240.88 240.88 217.97
MOA of compression area mm2 29011910 29011910 23756190
MOA of tension area mm2 29011910 29011910 23756190
Diff 0 0 0
MOI of cracked section 1.70E+10 1.70E+10 1.40E+10

Stress in tension reinf MPa 0 0 69

Status OK OK OK
Stress in concrete MPa 0.00 0.00 1.83
Status OK OK OK
DESIGN OF RECTANGULAR BEAM / SLAB AS PER IRC : 112 - 2011
Type
Type of element ( B for Beam & S for Slab ) Refereance Unit S S S
Sections
Top Slab
Haunch Face At deff from
Span
End Haunch End
Load Data
Moment kN-m 132.57 125.7 0
Top Slab bottom face there is no Sagging moment in service stage (Please refer Staad Model)
Material Data
Grade of Steel Fe 500 Fe 500 Fe 500
Charecteristic strength of reinforcement ( fyk ) Table 18.1, IRC 112 MPa 500 500 500
partial factor for steel ( gs ) Cl 6.2.2, IRC 112 1.15 1.15 1.15
Design value for tensile strength ( fyd = fyk/gs ) Cl 6.2.2, IRC 112 MPa 435 435 435
Modulus of Elasticity of Steel ( Es ) Cl 6.2.2, IRC 112 GPa 200.00 200 200
Grade of Concrete M 35 M 35 M 35
Charecteristics compressive strength ( fck ) Table 6.5, IRC 112 MPa 35 35 35
a Cl 6.4.2.8, IRC 112 0.67 0.67 0.67
Concrete material factor ( gm ) Cl 6.4.2.8, IRC 112 1.50 1.5 1.5
Design value for concrete compressive strength ( f cd = afck/gm ) Cl 6.4.2.8, IRC 112 MPa 15.63 15.63 15.63
Modulus of Elasticity of Concrete ( Ecm ) Table 6.5, IRC 112 GPa 30 30 30

Geometric Data
Width of Slab / Beam ( b ) mm 1000 1000 1000
Total Depth of Beam ( D ) mm 700 700 700
Cover to Reinforcement ( c ) mm 45 45 45
Dia of Reinforcement ( f ) mm 16 16 20
Effective depth of beam / Slab ( d ) mm 647 647 647
Spacing of Reinforcement ( s ) or mm 170 170 170
Number of Bar ( n ) Nos 0 0 0
Area of Reinforcement ( At ) mm2 3031 3031 1848
Reinforcement ( % ) 0.433 0.433 0.264
( check done for Top slab final
Crack width check monolithic stage=Service Stage+const
stage)
Concrete Cross Sectional Area ( Ac ) mm 700000 700000 700000
Perimeter in contact with atmosphere ( u ) mm 3400 3400 3400
Notional Size 412 412 412
Final time for creep calculation, t (70 yrs) days 25550 25550 25550
Final Creep Co-efficient of 28 days ( f ) Table 6.9 & RH = 80% 1.78 1.78 1.78
Relative Humidity, RH 80 80 80
Coefficient to consider influence of the conc strength, α1 =
(43.75/fcm)0.7 Eq A2-24 IRC112-2011 0.980 0.980 0.980
Coefficient to consider influence of the conc strength, α2 =
(43.75/fcm)0.2 Eq A2-24 IRC112-2011 0.994 0.994 0.994
Coefficient to consider influence of the conc strength, α3 =
(43.75/fcm)0.5 Eq A2-24 IRC112-2011 0.986 0.986 0.986
Factor to allow for the effect of relative humidity, fRH
= (1+ (1-RH/100)/0.1(ho)1/3 ) for fcm ≤ 45MPa &
(1+ (1-RH/100) x α1/0.1(ho)1/3 )α2 for fcm > 45MPa Eq A2-16,17 IRC112-2011 1.269 1.269 1.269

Factor to allow for effect of conc age at loading, b (to) = 1/(0.1+t00.2) Eq A2-19 IRC112-2011 0.488 0.488 0.488
Factor to allow for effect of conc strength, b (fcm) = 18.78/√fcm Eq A2-18 IRC112-2011 2.800 2.800 2.800
fo = fRH b(fcm) b(to) Eq A2-15 IRC112-2011 1.735 1.735 1.735
fcm Table 6.5 IRC112-2011 MPa 45.000 45.000 45.000
Coefficient depending on RH and member size (for deck), bH
=1.5[1+(0.012RH)18]h0+250 ≤1500 for fcm≤ 45 &
1.5[1+(0.012RH)18]h0+250a3 ≤1500α3 for fcm> 45 Eq A2-22,23 IRC112-2011 1163.873 1163.873 1163.873
Coefficient to describe the development of creep with time, bc(t,to)
= [(t-to)/(bH+t-to)]0.3 Eq A2-21 IRC112-2011 0.987 0.987 0.987
Creep coefficient, f (t,to) = f0.bc(t,t0) Eq A2-14 IRC112-2011 1.712 1.712 1.712
Effective Modulus of Elasticity of Conc. ( Eeff ) Cl 6.4.2.5, IRC 112 MPa 10777 10777 10777
Modular ratio ( m ) 18.56 18.56 18.56

Allowable stress in steel Cl 12.2.2, IRC 112 MPa 400 400 400
Allowable stress in concrete Cl 12.2.1, IRC 112 MPa 12.60 12.60 12.60
Position of nutural axis from comp face ( x ) mm 219 219 179
MOA of compression area mm2 24053373 24053373 16045157
MOA of tension area mm2 24053373 24053373 16045157
Diff 0 0 0
MOI of cracked section 1.38E+10 1.38E+10 9.42E+09
Stress in tension reinf MPa 76 72 0
Effective area of concrete in tension surrounding
the reinforcement, Ac,eff = b x hc,eff mm2 106000 106000 110000
Depth of concrete in tension hc,eff = mm 106 106 110
ae = Es / Ecm 6.67 6.67 6.67
rr,eff = 0.029 0.029 0.017
kt = A factor dependent on the duration of the load Cl 12.3.4, IRC 112 0.5 0.5 0.5
DESIGN OF RECTANGULAR BEAM / SLAB AS PER IRC : 112 - 2011
Type
Type of element ( B for Beam & S for Slab ) Refereance Unit S S S
Sections
Mean value of tensile strength of concrete effective at the time Top Slab
when the cracks may occur first, fct,eff = fctm (t) Cl 12.3.3, IRC 112
where, fctm(t) = (bcc(t))a x fctm
and the value of fctm is = Table 6.5, IRC 112 MPa 2.50 2.50 2.50
where, bcc(t) = e ^ [S x (1 - (28/(t/t1))^0.5] Eq 6.3, IRC 112
bcc(t) = Co-eff depending on age "t" and type of cement
t = Age of concrete in days = 28 28 28
t1 = Eq 6.3, IRC 112 1 1 1
S = Co-efficient depends on type of cement = Eq 6.3, IRC 112 0.25 0.25 0.25
So, bcc(t) = e ^ [S x (1 - (28/(t/t1))^0.5] 1 1 1
fct,eff = fctm (t) MPa 3 3 3
Maximum Crack Spacing, Sr,max = 1.3 x (h - x) = Eq 12.12, IRC 112 mm 625 625 677
Maximum Crack Spacing, Sr,max = 3.4c + (0.425xk1xk2xf)/rr,eff Eq 12.12, IRC 113 mm 248 248 355
k1 = Cl 12.3.4, IRC 112 0.8 0.8 0.8
k2 = Cl 12.3.4, IRC 112 0.5 0.5 0.5
f= mm 16 16 20
Maximum Crack Spacing, Sr,max = 3.4c + (0.17f)/rr,eff Eq 12.8, IRC 112 mm 248 248 355
Design Crack Spacing, Sr,max = Eq 12.12, IRC 112 mm 248 248 355
As per Eq 12.6 of IRC: 112-2011
esm -ecm = ((ssc - (kt x fct,eff x (1 + ae x rr,eff))/rr,eff))/Es 0.0002 0.0002 0.0000
Crack width ( wk ) Eq 12.5, IRC 112 mm 0.06 0.05 0.00
Status Table 12.1, IRC 112 OK OK OK

Check for Deflection (SLS: Frequent Combination)

Permissible Deflection Cl 12.4, IRC 112 mm 15.88
Momemt in Frequent Combinations Ton-m 4
Deflection mm 12.70 0.458
Status OK

Minimum Area of Reinforcement for Crack Control (as per Cl. 12.3.3 of IRC:112 - 2011)

Ned= Axial Force In Serviceability Limit State 191 191 191

Ned,Tensile or Compresive C C C
sc=Ned/bh Eq 12.4, IRC 112 MPa 0.27 0.27 0.27
k1 Cl 12.3.3, IRC 112 1.50 1.50 1.50
h* Cl 12.3.3, IRC 112 mm 700 700 700
For Rectangular Section with bending the value of kc is :--
0.4 x {1 - sc/(k1 x (h/h*) x fct,eff)} Eq 12.2, IRC 112 0.375 0.375 0.375
Co-efficient which allows for the effect of non-uniform self equilibrating stress, k = 1.00 1.00 1.00
2
Minimum area of Reinf. Reqd. Cl 12.3.3, IRC 112 mm 231 231 239
Status O.K. O.K. O.K.
DESIGN OF RECTANGULAR BEAM / SLAB AS PER IRC : 112 - 2011
Type
Type of element ( B for Beam & S for Slab ) Refereance Unit
Sections
OUTER WALL
At 2 Deff At 2 Deff
Top from Haunch Centre from Haunch Bottom
Load Data End End
Moment kN-m 140.17 102.65 116.68 149.03 271.12
Top Slab bottom face there is no Sagging moment in service stage (Please refer Staad Model)
Material Data
Grade of Steel Fe 500 Fe 500 Fe 500 Fe 500 Fe 500
Charecteristic strength of reinforcement ( fyk ) Table 18.1, IRC 112 MPa 500 500 500 500 500
partial factor for steel ( gs ) Cl 6.2.2, IRC 112 1.15 1.15 1.15 1.15 1.15
Design value for tensile strength ( fyd = fyk/gs ) Cl 6.2.2, IRC 112 MPa 435 435 435 435 435
Modulus of Elasticity of Steel ( Es ) Cl 6.2.2, IRC 112 GPa 200 200 200 200 200
Grade of Concrete M 35 M 35 M 35 M 35 M 35
Charecteristics compressive strength ( fck ) Table 6.5, IRC 112 MPa 35 35 35 35 35
a Cl 6.4.2.8, IRC 112 0.67 0.67 0.67 0.67 0.67
Concrete material factor ( gm ) Cl 6.4.2.8, IRC 112 1.5 1.5 1.5 1.5 1.5
Design value for concrete compressive strength ( f cd = afck/gm ) Cl 6.4.2.8, IRC 112 MPa 15.63 15.63 15.63 15.63 15.63
Modulus of Elasticity of Concrete ( Ecm ) Table 6.5, IRC 112 GPa 30 30 30 30 30

Geometric Data
Width of Slab / Beam ( b ) mm 1000 1000 1000 1000 1000
Total Depth of Beam ( D ) mm 700 700 700 700 700
Cover to Reinforcement ( c ) mm 75 75 75 75 75
Dia of Reinforcement ( f ) mm 20 20 25 20 20
Effective depth of beam / Slab ( d ) mm 615 615 643 615 615
Spacing of Reinforcement ( s ) or mm 170 170 170 170 170
Number of Bar ( n ) Nos 0 0 0 0 0
Area of Reinforcement ( At ) mm2 3031 3031 2887 3696 3696
Reinforcement ( % ) 0.433 0.433 0.412 0.528 0.528

Crack width check

Concrete Cross Sectional Area ( Ac ) mm 700000 700000 700000 700000 700000

Perimeter in contact with atmosphere ( u ) mm 3400 3400 3400 3400 3400
Notional Size 412 412 412 412 412
Final time for creep calculation, t (70 yrs) days 25550 25550 25550 25550 25550
Final Creep Co-efficient of 28 days ( f ) Table 6.9 & RH = 80% 1.78 1.78 1.78 1.78 1.78
Relative Humidity, RH 80 80 80 80 80
Coefficient to consider influence of the conc strength, α1 =
(43.75/fcm)0.7 Eq A2-24 IRC112-2011 0.980 0.980 0.980 0.980 0.980
Coefficient to consider influence of the conc strength, α2 =
(43.75/fcm)0.2 Eq A2-24 IRC112-2011 0.994 0.994 0.994 0.994 0.994
Coefficient to consider influence of the conc strength, α3 =
(43.75/fcm)0.5 Eq A2-24 IRC112-2011 0.986 0.986 0.986 0.986 0.986
Factor to allow for the effect of relative humidity, fRH
= (1+ (1-RH/100)/0.1(ho)1/3 ) for fcm ≤ 45MPa &
(1+ (1-RH/100) x α1/0.1(ho)1/3 )α2 for fcm > 45MPa Eq A2-16,17 IRC112-2011 1.269 1.269 1.269 1.269 1.269

Factor to allow for effect of conc age at loading, b (to) = 1/(0.1+t00.2) Eq A2-19 IRC112-2011 0.488 0.488 0.488 0.488 0.488
Factor to allow for effect of conc strength, b (fcm) = 18.78/√fcm Eq A2-18 IRC112-2011 2.800 2.800 2.800 2.800 2.800
fo = fRH b(fcm) b(to) Eq A2-15 IRC112-2011 1.735 1.735 1.735 1.735 1.735
fcm Table 6.5 IRC112-2011 MPa 45.000 45.000 45.000 45.000 45.000
Coefficient depending on RH and member size (for deck), bH
=1.5[1+(0.012RH)18]h0+250 ≤1500 for fcm≤ 45 &
1.5[1+(0.012RH)18]h0+250a3 ≤1500α3 for fcm> 45 Eq A2-22,23 IRC112-2011 1163.873 1163.873 1163.873 1163.873 1163.873
Coefficient to describe the development of creep with time, bc(t,to)
= [(t-to)/(bH+t-to)]0.3 Eq A2-21 IRC112-2011 0.987 0.987 0.987 0.987 0.987
Creep coefficient, f (t,to) = f0.bc(t,t0) Eq A2-14 IRC112-2011 1.712 1.712 1.712 1.712 1.712
Effective Modulus of Elasticity of Conc. ( Eeff ) Cl 6.4.2.5, IRC 112 MPa 10777 10777 10777 10777 10777
Modular ratio ( m ) 18.56 18.56 18.56 18.56 18.56

Allowable stress in steel Cl 12.2.2, IRC 112 MPa 400 400 400 400 400
Allowable stress in concrete Cl 12.2.1, IRC 112 MPa 12.60 12.60 12.60 12.60 12.60
Position of nutural axis from comp face ( x ) mm 213 213 214 230 230
MOA of compression area mm2 22625375 22625375 22948641 26416766 26416766
MOA of tension area mm2 22625375 22625375 22948641 26416766 26416766
Diff 0 0 0 0 0
MOI of cracked section 1.23E+10 1.23E+10 1.31E+10 1.42E+10 1.42E+10
Stress in tension reinf MPa 85 62 71 75 136
Effective area of concrete in tension surrounding
the reinforcement, Ac,eff = b x hc,eff mm2 170000 170000 143750 170000 170000
Depth of concrete in tension hc,eff = mm 170 170 143.75 170 170
ae = Es / Ecm 6.67 6.67 6.67 6.67 6.67
rr,eff = 0.018 0.018 0.020 0.022 0.022
kt = A factor dependent on the duration of the load Cl 12.3.4, IRC 112 0.5 0.5 0.5 0.5 0.5
DESIGN OF RECTANGULAR BEAM / SLAB AS PER IRC : 112 - 2011
Type
Type of element ( B for Beam & S for Slab ) Refereance Unit
Sections
Mean value of tensile strength of concrete effective at the time OUTER WALL
when the cracks may occur first, fct,eff = fctm (t) Cl 12.3.3, IRC 112
where, fctm(t) = (bcc(t))a x fctm
and the value of fctm is = Table 6.5, IRC 112 MPa 2.50 2.50 2.50 2.50 2.50
where, bcc(t) = e ^ [S x (1 - (28/(t/t1))^0.5] Eq 6.3, IRC 112
bcc(t) = Co-eff depending on age "t" and type of cement
t = Age of concrete in days = 28 28 28 28 28
t1 = Eq 6.3, IRC 112 1 1 1 1 1
S = Co-efficient depends on type of cement = Eq 6.3, IRC 112 0 0.25 0.25 0.25 0.25
So, bcc(t) = e ^ [S x (1 - (28/(t/t1))^0.5] 1 1 1 1 1
fct,eff = fctm (t) MPa 3 3 3 3 3
Maximum Crack Spacing, Sr,max = 1.3 x (h - x) = Eq 12.12, IRC 112 mm 633 633 631 611 611
Maximum Crack Spacing, Sr,max = 3.4c + (0.425xk1xk2xf)/rr,eff Eq 12.12, IRC 113 mm 446 446 467 411 411
k1 = Cl 12.3.4, IRC 112 0.8 0.8 0.8 0.8 0.8
k2 = Cl 12.3.4, IRC 112 0.5 0.5 0.5 0.5 0.5
f= mm 20 20 25 20 20
Maximum Crack Spacing, Sr,max = 3.4c + (0.17f)/rr,eff Eq 12.8, IRC 112 mm 446 446 467 411 411
Design Crack Spacing, Sr,max = Eq 12.12, IRC 112 mm 446 446 467 411 411
As per Eq 12.6 of IRC: 112-2011
esm -ecm = ((ssc - (kt x fct,eff x (1 + ae x rr,eff))/rr,eff))/Es 0.0003 0.0002 0.0002 0.0002 0.0004
Crack width ( wk ) Eq 12.5, IRC 112 mm 0.11 0.08 0.10 0.09 0.17
Status Table 12.1, IRC 112 OK OK OK OK OK

Check for Deflection (SLS: Frequent Combination)

Permissible Deflection Cl 12.4, IRC 112 mm 7.41 5.93
Momemt in Frequent Combinations Ton-m 34
Deflection mm 0.627
Status OK

Minimum Area of Reinforcement for Crack Control (as per Cl. 12.3.3 of IRC:112 - 2011)

Ned= Axial Force In Serviceability Limit State 280 309 337 352 395
Ned,Tensile or Compresive C C C C C
sc=Ned/bh Eq 12.4, IRC 112 MPa 0.40 0.44 0.48 0.50 0.56
k1 Cl 12.3.3, IRC 112 1.50 1.50 1.50 1.50 1.50
h* Cl 12.3.3, IRC 112 mm 700 700 700 700 700
For Rectangular Section with bending the value of kc is :--
0.4 x {1 - sc/(k1 x (h/h*) x fct,eff)} Eq 12.2, IRC 112 0.363 0.359 0.356 0.354 0.348
Co-efficient which allows for the effect of non-uniform self equilibrating stress, k = 1.00 1.00 1.00 1.00 1.00
2
Minimum area of Reinf. Reqd. Cl 12.3.3, IRC 112 mm 358 354 297 349 343
Status O.K. O.K. O.K. O.K. O.K.
DESIGN OF RECTANGULAR BEAM / SLAB AS PER IRC : 112 - 2011
Type
Type of element ( B for Beam & S for Slab ) Refereance Unit
Sections
BOTTOM SLAB
At 2 Deff
Haunch Face from Haunch Span
Load Data End
Moment kN-m 326.71 264.94 330.71
Top Slab bottom face there is no Sagging moment in service stage (Please refer Staad Model)
Material Data
Grade of Steel Fe 500 Fe 500 Fe 500
Charecteristic strength of reinforcement ( fyk ) Table 18.1, IRC 112 MPa 500 500 500
partial factor for steel ( gs ) Cl 6.2.2, IRC 112 1.15 1.15 1.15
Design value for tensile strength ( fyd = fyk/gs ) Cl 6.2.2, IRC 112 MPa 435 435 435
Modulus of Elasticity of Steel ( Es ) Cl 6.2.2, IRC 112 GPa 200 200 200
Grade of Concrete M 35 M 35 M 35
Charecteristics compressive strength ( fck ) Table 6.5, IRC 112 MPa 35 35 35
a Cl 6.4.2.8, IRC 112 0.67 0.67 0.67
Concrete material factor ( gm ) Cl 6.4.2.8, IRC 112 1.5 1.5 1.5
Design value for concrete compressive strength ( f cd = afck/gm ) Cl 6.4.2.8, IRC 112 MPa 15.63 15.63 15.63
Modulus of Elasticity of Concrete ( Ecm ) Table 6.5, IRC 112 GPa 30 30 30

Geometric Data
Width of Slab / Beam ( b ) mm 1000 1000 1000
Total Depth of Beam ( D ) mm 750 750 750
Cover to Reinforcement ( c ) mm 75 75 75
Dia of Reinforcement ( f ) mm 20 20 25
Effective depth of beam / Slab ( d ) mm 665 665 662.5
Spacing of Reinforcement ( s ) or mm 85 85 170
Number of Bar ( n ) Nos 0 0 0
Area of Reinforcement ( At ) mm2 3696 3696 2887
Reinforcement ( % ) 0.493 0.493 0.385

Crack width check

Concrete Cross Sectional Area ( Ac ) mm 750000 750000 750000

Perimeter in contact with atmosphere ( u ) mm 3500 3500 3500
Notional Size 429 429 429
Final time for creep calculation, t (70 yrs) days 25550 25550 25550
Final Creep Co-efficient of 28 days ( f ) Table 6.9 & RH = 80% 1.78 1.78 1.78
Relative Humidity, RH 80 80 80
Coefficient to consider influence of the conc strength, α1 =
(43.75/fcm)0.7 Eq A2-24 IRC112-2011 0.980 0.980 0.980
Coefficient to consider influence of the conc strength, α2 =
(43.75/fcm)0.2 Eq A2-24 IRC112-2011 0.994 0.994 0.994
Coefficient to consider influence of the conc strength, α3 =
(43.75/fcm)0.5 Eq A2-24 IRC112-2011 0.986 0.986 0.986
Factor to allow for the effect of relative humidity, fRH
= (1+ (1-RH/100)/0.1(ho)1/3 ) for fcm ≤ 45MPa &
(1+ (1-RH/100) x α1/0.1(ho)1/3 )α2 for fcm > 45MPa Eq A2-16,17 IRC112-2011 1.265 1.265 1.265

Factor to allow for effect of conc age at loading, b (to) = 1/(0.1+t00.2) Eq A2-19 IRC112-2011 0.488 0.488 0.488
Factor to allow for effect of conc strength, b (fcm) = 18.78/√fcm Eq A2-18 IRC112-2011 2.800 2.800 2.800
fo = fRH b(fcm) b(to) Eq A2-15 IRC112-2011 1.730 1.730 1.730
fcm Table 6.5 IRC112-2011 MPa 45.000 45.000 45.000
Coefficient depending on RH and member size (for deck), bH
=1.5[1+(0.012RH)18]h0+250 ≤1500 for fcm≤ 45 &
1.5[1+(0.012RH)18]h0+250a3 ≤1500α3 for fcm> 45 Eq A2-22,23 IRC112-2011 1201.174 1201.174 1201.174
Coefficient to describe the development of creep with time, bc(t,to)
= [(t-to)/(bH+t-to)]0.3 Eq A2-21 IRC112-2011 0.986 0.986 0.986
Creep coefficient, f (t,to) = f0.bc(t,t0) Eq A2-14 IRC112-2011 1.706 1.706 1.706
Effective Modulus of Elasticity of Conc. ( Eeff ) Cl 6.4.2.5, IRC 112 MPa 10806 10806 10806
Modular ratio ( m ) 18.51 18.51 18.51

Allowable stress in steel Cl 12.2.2, IRC 112 MPa 400 400 400
Allowable stress in concrete Cl 12.2.1, IRC 112 MPa 12.60 12.60 12.60
Position of nutural axis from comp face ( x ) mm 241 241 218
MOA of compression area mm2 29011910 29011910 23756190
MOA of tension area mm2 29011910 29011910 23756190
Diff 0 0 0
MOI of cracked section 1.70E+10 1.70E+10 1.40E+10
Stress in tension reinf MPa 151 123 194
Effective area of concrete in tension surrounding
the reinforcement, Ac,eff = b x hc,eff mm2 170000 170000 175000
Depth of concrete in tension hc,eff = mm 170 170 175
ae = Es / Ecm 6.67 6.67 6.67
rr,eff = 0.022 0.022 0.016
kt = A factor dependent on the duration of the load Cl 12.3.4, IRC 112 0.5 0.5 0.5
DESIGN OF RECTANGULAR BEAM / SLAB AS PER IRC : 112 - 2011
Type
Type of element ( B for Beam & S for Slab ) Refereance Unit
Sections
Mean value of tensile strength of concrete effective at the time BOTTOM SLAB
when the cracks may occur first, fct,eff = fctm (t) Cl 12.3.3, IRC 112
where, fctm(t) = (bcc(t))a x fctm
and the value of fctm is = Table 6.5, IRC 112 MPa 2.50 2.50 2.50
where, bcc(t) = e ^ [S x (1 - (28/(t/t1))^0.5] Eq 6.3, IRC 112
bcc(t) = Co-eff depending on age "t" and type of cement
t = Age of concrete in days = 28 28 28
t1 = Eq 6.3, IRC 112 1 1 1
S = Co-efficient depends on type of cement = Eq 6.3, IRC 112 0.25 0.25 0.25
So, bcc(t) = e ^ [S x (1 - (28/(t/t1))^0.5] 1 1 1
fct,eff = fctm (t) MPa 3 3 3
Maximum Crack Spacing, Sr,max = 1.3 x (h - x) = Eq 12.12, IRC 112 mm 662 662 692
Maximum Crack Spacing, Sr,max = 3.4c + (0.425xk1xk2xf)/rr,eff Eq 12.12, IRC 113 mm 411 411 513
k1 = Cl 12.3.4, IRC 112 0.8 0.8 0.8
k2 = Cl 12.3.4, IRC 112 0.5 0.5 0.5
f= mm 20 20 25
Maximum Crack Spacing, Sr,max = 3.4c + (0.17f)/rr,eff Eq 12.8, IRC 112 mm 411 411 513
Design Crack Spacing, Sr,max = Eq 12.12, IRC 112 mm 411 411 513
As per Eq 12.6 of IRC: 112-2011
esm -ecm = ((ssc - (kt x fct,eff x (1 + ae x rr,eff))/rr,eff))/Es 0.0005 0.0004 0.0006
Crack width ( wk ) Eq 12.5, IRC 112 mm 0.19 0.15 0.30
Status Table 12.1, IRC 112 OK OK OK

Check for Deflection (SLS: Frequent Combination)

Permissible Deflection Cl 12.4, IRC 112 mm 15.88
Momemt in Frequent Combinations Ton-m 4
Deflection mm 0.254
Status OK

Minimum Area of Reinforcement for Crack Control (as per Cl. 12.3.3 of IRC:112 - 2011)

Ned= Axial Force In Serviceability Limit State 434 434 434

Ned,Tensile or Compresive C C C
sc=Ned/bh Eq 12.4, IRC 112 MPa 0.58 0.58 0.58
k1 Cl 12.3.3, IRC 112 1.50 1.50 1.50
h* Cl 12.3.3, IRC 112 mm 750 750 750
For Rectangular Section with bending the value of kc is :--
0.4 x {1 - sc/(k1 x (h/h*) x fct,eff)} Eq 12.2, IRC 112 0.347 0.347 0.347
Co-efficient which allows for the effect of non-uniform self equilibrating stress, k = 1.00 1.00 1.00
2
Minimum area of Reinf. Reqd. Cl 12.3.3, IRC 112 mm 342 342 352
Status O.K. O.K. O.K.
BASE PRESSURE CHECK

load case No. Reaction Length of Base Max Base Min Base
Sturcture Pressure pressure Pressure
101 723.536 12.35 58.586
102 723.536 12.35 58.586
103 794.643 12.35 64.344
104 794.645 12.35 64.344
105 794.645 12.35 64.344
64.344 58.586
106 794.645 12.35 64.344
107 794.645 12.35 64.344
108 794.645 12.35 64.344
109 794.645 12.35 64.344
110 794.646 12.35 64.344

Maximum Allowable SBC= 70

Max Base pressure = 64.344 < 70 ok
Min Base Pressure = 58.586 > 0 ok
STAAD PLANE RCC BOX
START JOB INFORMATION
ENGINEER DATE 2023-10-30
ENGINEER NAME KG
CHECKER NAME MA
END JOB INFORMATION
INPUT WIDTH 79
SET ECHO OFF
PAGE LENGTH 100000
UNIT METER KN
JOINT COORDINATES
1 0.000 0.000 0.000 ;
2 0.35 0.000 0.000 ;
3 0.65 0.000 0.000 ;
4 1.318 0.000 0.000 ;
5 3.7975 0.000 0.000 ;
6 6.277 0.000 0.000 ;
7 8.7565 0.000 0.000 ;
8 11.236 0.000 0.000 ;
9 11.904 0.000 0.000 ;
10 12.204 0.000 0.000 ;
11 12.554 0.000 0.000 ;
12 0.000 6.225 0.000 ;
13 0.35 6.225 0.000 ;
14 0.65 6.225 0.000 ;
15 1.318 6.225 0.000 ;
16 3.7975 6.225 0.000 ;
17 6.277 6.225 0.000 ;
18 8.7565 6.225 0.000 ;
19 11.236 6.225 0.000 ;
20 11.904 6.225 0.000 ;
21 12.204 6.225 0.000 ;
22 12.554 6.225 0.000 ;
23 0.000 0.375 0.000 ;
24 0.000 0.675 0.000 ;
25 0.000 1.905 0.000 ;
26 0.000 2.515 0.000 ;
27 0.000 3.125 0.000 ;
28 0.000 3.735 0.000 ;
29 0.000 4.345 0.000 ;
30 0.000 5.575 0.000 ;
31 0.000 5.875 0.000 ;
32 12.554 0.375 0.000 ;
33 12.554 0.675 0.000 ;
34 12.554 1.905 0.000 ;
35 12.554 2.515 0.000 ;
36 12.554 3.125 0.000 ;
37 12.554 3.735 0.000 ;
38 12.554 4.345 0.000 ;
39 12.554 5.575 0.000 ;
40 12.554 5.875 0.000 ;
MEMBER INCIDENCES
112;
223;
334;
445;
556;
667;
778;
889;
9 9 10 ;
10 10 11 ;
11 12 13 ;
12 13 14 ;
13 14 15 ;
14 15 16 ;
15 16 17 ;
16 17 18 ;
17 18 19 ;
18 19 20 ;
19 20 21 ;
20 21 22 ;
21 1 23 ;
22 23 24 ;
23 24 25 ;
24 25 26 ;
25 26 27 ;
26 27 28 ;
27 28 29 ;
28 29 30 ;
29 30 31 ;
30 31 12 ;
31 11 32 ;
32 32 33 ;
33 33 34 ;
34 34 35 ;
35 35 36 ;
36 36 37 ;
37 37 38 ;
38 38 39 ;
39 39 40 ;
40 40 22 ;
MEMBER PROPERTY INDIAN
*Bottom Slab
3 TO 8 PRIS YD 0.75 ZD 1
2 9 PRIS YD 0.9 ZD 1
1 10 PRIS YD 1.05 ZD 1
*Top Slab
13 TO 18 PRIS YD 0.7 ZD 1
12 19 PRIS YD 1 ZD 1
11 20 PRIS YD 1 ZD 1
*Vertical Wall (Outer)
23 TO 28 33 TO 38 PRIS YD 0.7 ZD 1
22 29 32 39 PRIS YD 0.85 ZD 1
21 30 31 40 PRIS YD 1 ZD 1
*Vertical Wall (Inner)
CONSTANTS
E 30000000 ALL
POISSON 0.15 ALL
DENSITY 25 ALL
SUPPORTS
1 FIXED BUT FZ MX MY MZ KFY 945
2 FIXED BUT FX FZ MX MY MZ KFY 585
3 FIXED BUT FX FZ MX MY MZ KFY 871.2
4 FIXED BUT FX FZ MX MY MZ KFY 2832.75
5 FIXED BUT FX FZ MX MY MZ KFY 4463.1
6 FIXED BUT FX FZ MX MY MZ KFY 4463.1
7 FIXED BUT FX FZ MX MY MZ KFY 4463.1
8 FIXED BUT FX FZ MX MY MZ KFY 2832.75
9 FIXED BUT FX FZ MX MY MZ KFY 871.2
10 FIXED BUT FX FZ MX MY MZ KFY 585
11 FIXED BUT FX FZ MX MY MZ KFY 315
LOAD 1 SELFWEIGHT
SELFWEIGHT Y -1.0
MEMBER LOAD
11 TO 20 UNI GY -0
LOAD 2 SIDL
MEMBER LOAD
11 TO 20 UNI GY -1.43
LOAD 3 EARTH PRESSURE AT REST (IN DRY CONDITION)
MEMBER LOAD
21 TRAP GX 66.4 62.65
22 TRAP GX 62.65 59.65
23 TRAP GX 59.65 47.35
24 TRAP GX 47.35 41.25
25 TRAP GX 41.25 35.15
26 TRAP GX 35.15 29.05
27 TRAP GX 29.05 22.95
28 TRAP GX 22.95 10.65
29 TRAP GX 10.65 7.65
30 TRAP GX 7.65 4.15
31 TRAP GX -66.4 -62.65
32 TRAP GX -62.65 -59.65
33 TRAP GX -59.65 -47.35
34 TRAP GX -47.35 -41.25
35 TRAP GX -41.25 -35.15
36 TRAP GX -35.15 -29.05
37 TRAP GX -29.05 -22.95
38 TRAP GX -22.95 -10.65
39 TRAP GX -10.65 -7.65
40 TRAP GX -7.65 -4.15
LOAD 4 EARTH PRESSURE AT REST SUBMERGED CONDITION
MEMBER LOAD
21 TRAP GX 98.4725 92.66
22 TRAP GX 92.66 88.01
23 TRAP GX 88.01 68.945
24 TRAP GX 68.945 59.4125
25 TRAP GX 59.4125 49.88
26 TRAP GX 49.88 40.3475
27 TRAP GX 40.3475 30.815
28 TRAP GX 30.815 8.65
28 TRAP GX 8.65 10.65
29 TRAP GX 10.65 7.65
30 TRAP GX 7.65 4.15
31 TRAP GX -98.4725 -92.66
32 TRAP GX -92.66 -88.01
33 TRAP GX -88.01 -68.945
34 TRAP GX -68.945 -59.4125
35 TRAP GX -59.4125 -49.88
36 TRAP GX -49.88 -40.3475
37 TRAP GX -40.3475 -30.815
38 TRAP GX -30.815 -8.65
38 TRAP GX -8.65 -10.65
39 TRAP GX -10.65 -7.65
40 TRAP GX -7.65 -4.15
LOAD 6 MAXIMUM LIVE LOAD CASE FOR BASE PRESSURE
MEMBER LOAD
18 CON GY -17.68 0.503
16 CON GY -8.63 2.462
15 CON GY -13.68 0.641
14 CON GY -15.53 1.921
11 CON GY -15.59 0.039
LOAD 7 MAXIMUM LIVE LOAD CASE FOR FOR TOP SLAB (HOGGING MOMENT)
MEMBER LOAD
16 CON GY -7.74 0.818
15 CON GY -8.4 0.298
13 CON GY -15.62 0.445
LOAD 8 MAXIMUM LIVE LOAD CASE FOR TOP SLAB (SHEAR)
MEMBER LOAD
17 CON GY -25 1.136
16 CON GY -20.83 2.246
16 CON GY -13.31 0.116
15 CON GY -13.82 1.075
13 CON GY -19.33 0.263
LOAD 9 MAXIMUM LIVE LOAD CASE FOR TOP SLAB (SAGGING MOMENT)
MEMBER LOAD
20 CON GY -31.71 0.213
17 CON GY -9.4 0.661
16 CON GY -7.64 0.14
14 CON GY -9.05 2.099
LOAD 10 MAXIMUM LIVE LOAD CASE FOR WALL TOP
MEMBER LOAD
20 CON GY -31.71 0.213
17 CON GY -9.4 0.661
16 CON GY -7.64 0.14
14 CON GY -9.05 2.099
LOAD 11 MAXIMUM LIVE LOAD CASE FOR WALL MIDDLE
MEMBER LOAD
20 CON GY -31.71 0.213
17 CON GY -9.4 0.661
16 CON GY -7.64 0.14
14 CON GY -9.05 2.099
LOAD 12 MAXIMUM LIVE LOAD CASE FOR WALL BOTTOM
MEMBER LOAD
17 CON GY -11.99 1.887
16 CON GY -7.92 1.366
15 CON GY -8.05 0.846
14 CON GY -12.92 0.325
LOAD 13 MAXIMUM LIVE LOAD CASE FOR BOTTOM SLAB (SAGGING)
MEMBER LOAD
18 CON GY -17.68 0.503
16 CON GY -8.63 2.462
15 CON GY -13.68 0.641
14 CON GY -15.53 1.921
11 CON GY -15.59 0.039
LOAD 14 MAXIMUM LIVE LOAD CASE FOR BOTTOM SLAB (SHEAR)
MEMBER LOAD
18 CON GY -17.68 0.503
16 CON GY -8.63 2.462
15 CON GY -13.68 0.641
14 CON GY -15.53 1.921
11 CON GY -15.59 0.039
LOAD 15 MAXIMUM LIVE LOAD CASE FOR BOTTOM SLAB (HOGGING MOMENT)
MEMBER LOAD
17 CON GY -11.05 1.548
16 CON GY -7.79 1.027
15 CON GY -8.25 0.507
11 CON GY -71.92 0.004
LOAD 16 LIVE LOAD SURCHARGE BOTH SIDE
MEMBER LOAD
21 TO 30 UNI GX 12
31 TO 40 UNI GX -12
LOAD 17 LIVE LOAD SURCHARGE LHS SIDE
MEMBER LOAD
21 TO 30 UNI GX 12
LOAD 18 LIVE LOAD SURCHARGE RHS SIDE
MEMBER LOAD
31 TO 40 UNI GX -12
LOAD 19 BRAKING LHS SIDE FOR BASE PRESSURE
JOINT LOAD
12 FX 8.68968414957874
LOAD 20 BRAKING RHS SIDE FOR BASE PRESSURE
JOINT LOAD
22 FX -8.68968414957874
LOAD 21 BRAKING LHS SIDE FOR TOP SLAB (HOGGING MOMENT)
JOINT LOAD
12 FX 5.54897931780588
LOAD 22 BRAKING RHS SIDE FOR TOP SLAB (HOGGING MOMENT)
JOINT LOAD
22 FX -5.54897931780588
LOAD 23 BRAKING LHS SIDE FOR TOP SLAB (SHEAR)
JOINT LOAD
12 FX 18.8863509009793
LOAD 24 BRAKING RHS SIDE FOR TOP SLAB (SHEAR)
JOINT LOAD
22 FX -18.8863509009793
LOAD 25 BRAKING LHS SIDE FOR TOP SLAB (SAGGING MOMENT)
JOINT LOAD
12 FX 19.8029205903639
LOAD 26 BRAKING RHS SIDE FOR TOP SLAB (SAGGING MOMENT)
JOINT LOAD
22 FX -19.8029205903639
LOAD 27 BRAKING LHS SIDE FOR WALL (TOP)
JOINT LOAD
12 FX 19.8029205903639
LOAD 28 BRAKING RHS SIDE FOR WALL (TOP)
JOINT LOAD
22 FX -19.8029205903639
LOAD 29 BRAKING LHS SIDE FOR WALL (MIDDLE)
JOINT LOAD
12 FX 19.8029205903639
LOAD 30 BRAKING RHS SIDE FOR WALL (MIDDLE)
JOINT LOAD
22 FX -19.8029205903639
LOAD 31 BRAKING LHS SIDE FOR WALL (BOTTOM)
JOINT LOAD
12 FX 8.53808856713355
LOAD 32 BRAKING RHS SIDE FOR WALL (BOTTOM)
JOINT LOAD
22 FX -8.53808856713355
LOAD 33 BRAKING LHS SIDE FOR BOTTOM SLAB (SAGGING)
JOINT LOAD
12 FX 8.68968414957874
LOAD 34 BRAKING RHS SIDE FOR BOTTOM SLAB (SAGGING)
JOINT LOAD
22 FX -8.68968414957874
LOAD 35 BRAKING LHS SIDE FOR BOTTOM SLAB (SHEAR)
JOINT LOAD
12 FX 8.68968414957874
LOAD 36 BRAKING RHS SIDE FOR BOTTOM SLAB (SHEAR)
JOINT LOAD
22 FX -8.68968414957874
LOAD 37 BRAKING LHS SIDE FOR BOTTOM SLAB (HOGGING)
JOINT LOAD
12 FX 11.7524779407626
LOAD 38 BRAKING RHS SIDE FOR BOTTOM SLAB (HOGGING)
JOINT LOAD
22 FX -11.7524779407626
LOAD 39 TEMPERATURE LOAD (GRADIENT RISE)
JOINT LOAD
12 FX -534.6
12 MZ 79.002
22 FX 534.6
22 MZ -79.002
LOAD 40 TEMPERATURE LOAD (GRADIENT FALL)
JOINT LOAD
12 FX -518.49
12 MZ 152.02005
22 FX 518.49
22 MZ -152.02005
LOAD 41 TEMPERATURE LOAD (UNIFORM RISE)
TEMPERATURE LOAD
11 TO 20 STRAIN 0.0004008
LOAD 42 TEMPERATURE LOAD (UNIFORM FALL)
TEMPERATURE LOAD
11 TO 20 STRAIN -0.0004008
****************LOAD Combination For Base Pressure Check
Load Comb 101
1 1.000 2 1.000 3 1.000
Load Comb 102
1 1.000 2 1.000 4 1.000
Load Comb 103
1 1.000 2 1.000 3 1.000 6 1.000 16 1.000 19 1.000
Load Comb 104
1 1.000 2 1.000 3 1.000 6 1.000 16 1.000 20 1.000
Load Comb 105
1 1.000 2 1.000 3 1.000 6 1.000 17 1.000 19 1.000
Load Comb 106
1 1.000 2 1.000 3 1.000 6 1.000 18 1.000 20 1.000
Load Comb 107
1 1.000 2 1.000 4 1.000 6 1.000 16 1.000 19 1.000
Load Comb 108
1 1.000 2 1.000 4 1.000 6 1.000 16 1.000 20 1.000
Load Comb 109
1 1.000 2 1.000 4 1.000 6 1.000 17 1.000 19 1.000
Load Comb 110
1 1.000 2 1.000 4 1.000 6 1.000 18 1.000 20 1.000
****************LOAD Combination For Design of Top Slab , Wall & Bottom Slab
Load Comb 201
1 1.35 2 1.75 3 1.50
Load Comb 202
1 1.35 2 1.75 3 1.50 7 1.15 16 1.20 21 1.15
Load Comb 203
1 1.35 2 1.75 3 1.50 7 1.15 16 1.20 22 1.15
Load Comb 204
1 1.35 2 1.75 3 1.50 7 1.15 17 1.20 21 1.15
Load Comb 205
1 1.35 2 1.75 3 1.50 7 1.15 18 1.20 22 1.15
Load Comb 206
1 1.35 2 1.75 3 1.00 7 1.50 18 1.20 22 1.50
Load Comb 207
1 1.35 2 1.75 3 1.00 7 1.50 16 1.20 22 1.50
Load Comb 208
1 1.35 2 1.75 3 1.00 7 1.50 17 1.20 21 1.50
Load Comb 209
1 1.35 2 1.75 3 1.00 7 1.50 18 1.20 22 1.50
Load Comb 210
1 1.35 2 1.75 3 1.50 8 1.15 16 1.20 23 1.15
Load Comb 211
1 1.35 2 1.75 3 1.50 8 1.15 16 1.20 24 1.15
Load Comb 212
1 1.35 2 1.75 3 1.50 8 1.15 17 1.20 23 1.15
Load Comb 213
1 1.35 2 1.75 3 1.50 8 1.15 18 1.20 24 1.15
Load Comb 214
1 1.35 2 1.75 3 1.00 8 1.50 18 1.20 24 1.50
Load Comb 215
1 1.35 2 1.75 3 1.00 8 1.50 16 1.20 24 1.50
Load Comb 216
1 1.35 2 1.75 3 1.00 8 1.50 17 1.20 23 1.50
Load Comb 217
1 1.35 2 1.75 3 1.00 8 1.50 18 1.20 24 1.50
Load Comb 218
1 1.35 2 1.75 3 1.50 9 1.15 16 1.20 25 1.15
Load Comb 219
1 1.35 2 1.75 3 1.50 9 1.15 16 1.20 26 1.15
Load Comb 220
1 1.35 2 1.75 3 1.50 9 1.15 17 1.20 25 1.15
Load Comb 221
1 1.35 2 1.75 3 1.50 9 1.15 18 1.20 26 1.15
Load Comb 222
1 1.35 2 1.75 3 1.00 9 1.50 18 1.20 26 1.50
Load Comb 223
1 1.35 2 1.75 3 1.00 9 1.50 16 1.20 26 1.50
Load Comb 224
1 1.35 2 1.75 3 1.00 9 1.50 17 1.20 25 1.50
Load Comb 225
1 1.35 2 1.75 3 1.00 9 1.50 18 1.20 26 1.50
Load Comb 226
1 1.35 2 1.75 3 1.50 10 1.15 16 1.20 27 1.15
Load Comb 227
1 1.35 2 1.75 3 1.50 10 1.15 16 1.20 28 1.15
Load Comb 228
1 1.35 2 1.75 3 1.50 10 1.15 17 1.20 27 1.15
Load Comb 229
1 1.35 2 1.75 3 1.50 10 1.15 18 1.20 28 1.15
Load Comb 230
1 1.35 2 1.75 3 1.00 10 1.50 18 1.20 28 1.50
Load Comb 231
1 1.35 2 1.75 3 1.00 10 1.50 16 1.20 28 1.50
Load Comb 232
1 1.35 2 1.75 3 1.00 10 1.50 17 1.20 27 1.50
Load Comb 233
1 1.35 2 1.75 3 1.00 10 1.50 18 1.20 28 1.50
Load Comb 234
1 1.35 2 1.75 3 1.50 11 1.15 16 1.20 29 1.15
Load Comb 235
1 1.35 2 1.75 3 1.50 11 1.15 16 1.20 30 1.15
Load Comb 236
1 1.35 2 1.75 3 1.50 11 1.15 17 1.20 29 1.15
Load Comb 237
1 1.35 2 1.75 3 1.50 11 1.15 18 1.20 30 1.15
Load Comb 238
1 1.35 2 1.75 3 1.00 11 1.50 18 1.20 30 1.50
Load Comb 239
1 1.35 2 1.75 3 1.00 11 1.50 16 1.20 30 1.50
Load Comb 240
1 1.35 2 1.75 3 1.00 11 1.50 17 1.20 29 1.50
Load Comb 241
1 1.35 2 1.75 3 1.00 11 1.50 18 1.20 30 1.50
Load Comb 242
1 1.35 2 1.75 3 1.50 12 1.15 16 1.20 31 1.15
Load Comb 243
1 1.35 2 1.75 3 1.50 12 1.15 16 1.20 32 1.15
Load Comb 244
1 1.35 2 1.75 3 1.50 12 1.15 17 1.20 31 1.15
Load Comb 245
1 1.35 2 1.75 3 1.50 12 1.15 18 1.20 32 1.15
Load Comb 246
1 1.35 2 1.75 3 1.00 12 1.50 18 1.20 32 1.50
Load Comb 247
1 1.35 2 1.75 3 1.00 12 1.50 16 1.20 32 1.50
Load Comb 248
1 1.35 2 1.75 3 1.00 12 1.50 17 1.20 31 1.50
Load Comb 249
1 1.35 2 1.75 3 1.00 12 1.50 18 1.20 32 1.50
Load Comb 250
1 1.35 2 1.75 3 1.50 13 1.15 16 1.20 33 1.15
Load Comb 251
1 1.35 2 1.75 3 1.50 13 1.15 16 1.20 34 1.15
Load Comb 252
1 1.35 2 1.75 3 1.50 13 1.15 17 1.20 33 1.15
Load Comb 253
1 1.35 2 1.75 3 1.50 13 1.15 18 1.20 34 1.15
Load Comb 254
1 1.35 2 1.75 3 1.00 13 1.50 18 1.20 34 1.50
Load Comb 255
1 1.35 2 1.75 3 1.00 13 1.50 16 1.20 34 1.50
Load Comb 256
1 1.35 2 1.75 3 1.00 13 1.50 17 1.20 33 1.50
Load Comb 257
1 1.35 2 1.75 3 1.00 13 1.50 18 1.20 34 1.50
Load Comb 258
1 1.35 2 1.75 3 1.50 14 1.15 16 1.20 35 1.15
Load Comb 259
1 1.35 2 1.75 3 1.50 14 1.15 16 1.20 36 1.15
Load Comb 260
1 1.35 2 1.75 3 1.50 14 1.15 17 1.20 35 1.15
Load Comb 261
1 1.35 2 1.75 3 1.50 14 1.15 18 1.20 36 1.15
Load Comb 262
1 1.35 2 1.75 3 1.00 14 1.50 18 1.20 36 1.50
Load Comb 263
1 1.35 2 1.75 3 1.00 14 1.50 16 1.20 36 1.50
Load Comb 264
1 1.35 2 1.75 3 1.00 14 1.50 17 1.20 35 1.50
Load Comb 265
1 1.35 2 1.75 3 1.00 14 1.50 18 1.20 36 1.50
Load Comb 266
1 1.35 2 1.75 3 1.50 15 1.15 16 1.20 37 1.15
Load Comb 267
1 1.35 2 1.75 3 1.50 15 1.15 16 1.20 38 1.15
Load Comb 268
1 1.35 2 1.75 3 1.50 15 1.15 17 1.20 37 1.15
Load Comb 269
1 1.35 2 1.75 3 1.50 15 1.15 18 1.20 38 1.15
Load Comb 270
1 1.35 2 1.75 3 1.00 15 1.50 18 1.20 38 1.50
Load Comb 271
1 1.35 2 1.75 3 1.00 15 1.50 16 1.20 38 1.50
Load Comb 272
1 1.35 2 1.75 3 1.00 15 1.50 17 1.20 37 1.50
Load Comb 273
1 1.35 2 1.75 3 1.00 15 1.50 18 1.20 38 1.50
Load Comb 274
1 1.35 2 1.75 4 1.50
Load Comb 275
1 1.35 2 1.75 4 1.50 7 1.15 16 1.20 21 1.15
Load Comb 276
1 1.35 2 1.75 4 1.50 7 1.15 16 1.20 22 1.15
Load Comb 277
1 1.35 2 1.75 4 1.50 7 1.15 17 1.20 21 1.15
Load Comb 278
1 1.35 2 1.75 4 1.50 7 1.15 18 1.20 22 1.15
Load Comb 279
1 1.35 2 1.75 4 1.00 7 1.50 18 1.20 22 1.50
Load Comb 280
1 1.35 2 1.75 4 1.00 7 1.50 16 1.20 22 1.50
Load Comb 281
1 1.35 2 1.75 4 1.00 7 1.50 17 1.20 21 1.50
Load Comb 282
1 1.35 2 1.75 4 1.00 7 1.50 18 1.20 22 1.50
Load Comb 283
1 1.35 2 1.75 4 1.50 8 1.15 16 1.20 23 1.15
Load Comb 284
1 1.35 2 1.75 4 1.50 8 1.15 16 1.20 24 1.15
Load Comb 285
1 1.35 2 1.75 4 1.50 8 1.15 17 1.20 23 1.15
Load Comb 286
1 1.35 2 1.75 4 1.50 8 1.15 18 1.20 24 1.15
Load Comb 287
1 1.35 2 1.75 4 1.00 8 1.50 18 1.20 24 1.50
Load Comb 288
1 1.35 2 1.75 4 1.00 8 1.50 16 1.20 24 1.50
Load Comb 289
1 1.35 2 1.75 4 1.00 8 1.50 17 1.20 23 1.50
Load Comb 290
1 1.35 2 1.75 4 1.00 8 1.50 18 1.20 24 1.50
Load Comb 291
1 1.35 2 1.75 4 1.50 9 1.15 16 1.20 25 1.15
Load Comb 292
1 1.35 2 1.75 4 1.50 9 1.15 16 1.20 26 1.15
Load Comb 293
1 1.35 2 1.75 4 1.50 9 1.15 17 1.20 25 1.15
Load Comb 294
1 1.35 2 1.75 4 1.50 9 1.15 18 1.20 26 1.15
Load Comb 295
1 1.35 2 1.75 4 1.00 9 1.50 18 1.20 26 1.50
Load Comb 296
1 1.35 2 1.75 4 1.00 9 1.50 16 1.20 26 1.50
Load Comb 297
1 1.35 2 1.75 4 1.00 9 1.50 17 1.20 25 1.50
Load Comb 298
1 1.35 2 1.75 4 1.00 9 1.50 18 1.20 26 1.50
Load Comb 299
1 1.35 2 1.75 4 1.50 10 1.15 16 1.20 27 1.15
Load Comb 300
1 1.35 2 1.75 4 1.50 10 1.15 16 1.20 28 1.15
Load Comb 301
1 1.35 2 1.75 4 1.50 10 1.15 17 1.20 27 1.15
Load Comb 302
1 1.35 2 1.75 4 1.50 10 1.15 18 1.20 28 1.15
Load Comb 303
1 1.35 2 1.75 4 1.00 10 1.50 18 1.20 28 1.50
Load Comb 304
1 1.35 2 1.75 4 1.00 10 1.50 16 1.20 28 1.50
Load Comb 305
1 1.35 2 1.75 4 1.00 10 1.50 17 1.20 27 1.50
Load Comb 306
1 1.35 2 1.75 4 1.00 10 1.50 18 1.20 28 1.50
Load Comb 307
1 1.35 2 1.75 4 1.50 11 1.15 16 1.20 29 1.15
Load Comb 308
1 1.35 2 1.75 4 1.50 11 1.15 16 1.20 30 1.15
Load Comb 309
1 1.35 2 1.75 4 1.50 11 1.15 17 1.20 29 1.15
Load Comb 310
1 1.35 2 1.75 4 1.50 11 1.15 18 1.20 30 1.15
Load Comb 311
1 1.35 2 1.75 4 1.00 11 1.50 18 1.20 30 1.50
Load Comb 312
1 1.35 2 1.75 4 1.00 11 1.50 16 1.20 30 1.50
Load Comb 313
1 1.35 2 1.75 4 1.00 11 1.50 17 1.20 29 1.50
Load Comb 314
1 1.35 2 1.75 4 1.00 11 1.50 18 1.20 30 1.50
Load Comb 315
1 1.35 2 1.75 4 1.50 12 1.15 16 1.20 31 1.15
Load Comb 316
1 1.35 2 1.75 4 1.50 12 1.15 16 1.20 32 1.15
Load Comb 317
1 1.35 2 1.75 4 1.50 12 1.15 17 1.20 31 1.15
Load Comb 318
1 1.35 2 1.75 4 1.50 12 1.15 18 1.20 32 1.15
Load Comb 319
1 1.35 2 1.75 4 1.00 12 1.50 18 1.20 32 1.50
Load Comb 320
1 1.35 2 1.75 4 1.00 12 1.50 16 1.20 32 1.50
Load Comb 321
1 1.35 2 1.75 4 1.00 12 1.50 17 1.20 31 1.50
Load Comb 322
1 1.35 2 1.75 4 1.00 12 1.50 18 1.20 32 1.50
Load Comb 323
1 1.35 2 1.75 4 1.50 13 1.15 16 1.20 33 1.15
Load Comb 324
1 1.35 2 1.75 4 1.50 13 1.15 16 1.20 34 1.15
Load Comb 325
1 1.35 2 1.75 4 1.50 13 1.15 17 1.20 33 1.15
Load Comb 326
1 1.35 2 1.75 4 1.50 13 1.15 18 1.20 34 1.15
Load Comb 327
1 1.35 2 1.75 4 1.00 14 1.50 18 1.20 34 1.50
Load Comb 328
1 1.35 2 1.75 4 1.00 14 1.50 16 1.20 34 1.50
Load Comb 329
1 1.35 2 1.75 4 1.00 14 1.50 17 1.20 33 1.50
Load Comb 330
1 1.35 2 1.75 4 1.00 14 1.50 18 1.20 34 1.50
Load Comb 331
1 1.35 2 1.75 4 1.50 14 1.15 16 1.20 35 1.15
Load Comb 332
1 1.35 2 1.75 4 1.50 14 1.15 16 1.20 36 1.15
Load Comb 333
1 1.35 2 1.75 4 1.50 14 1.15 17 1.20 35 1.15
Load Comb 334
1 1.35 2 1.75 4 1.50 14 1.15 18 1.20 36 1.15
Load Comb 335
1 1.35 2 1.75 4 1.00 14 1.50 18 1.20 36 1.50
Load Comb 336
1 1.35 2 1.75 4 1.00 14 1.50 16 1.20 36 1.50
Load Comb 337
1 1.35 2 1.75 4 1.00 14 1.50 17 1.20 35 1.50
Load Comb 338
1 1.35 2 1.75 4 1.00 14 1.50 18 1.20 36 1.50
Load Comb 339
1 1.35 2 1.75 4 1.50 15 1.15 16 1.20 37 1.15
Load Comb 340
1 1.35 2 1.75 4 1.50 15 1.15 16 1.20 38 1.15
Load Comb 341
1 1.35 2 1.75 4 1.50 15 1.15 17 1.20 37 1.15
Load Comb 342
1 1.35 2 1.75 4 1.50 15 1.15 18 1.20 38 1.15
Load Comb 343
1 1.35 2 1.75 4 1.00 15 1.50 18 1.20 38 1.50
Load Comb 344
1 1.35 2 1.75 4 1.00 15 1.50 16 1.20 38 1.50
Load Comb 345
1 1.35 2 1.75 4 1.00 15 1.50 17 1.20 37 1.50
Load Comb 346
1 1.35 2 1.75 4 1.00 15 1.50 18 1.20 38 1.50
****************LOAD Combination For Stress Check
Load Comb 401
1 1.00 2 1.00 3 1.00
Load Comb 402
1 1.00 2 1.00 3 1.00 39 1.00 41 1.00
Load Comb 403
1 1.00 2 1.00 3 1.00 40 1.00 42 1.00
Load Comb 404
1 1.00 2 1.00 3 1.00 7 0.75 16 0.80 21 0.75 39 1.00 41 1.00
Load Comb 405
1 1.00 2 1.00 3 1.00 7 0.75 16 0.80 22 0.75 39 1.00 41 1.00
Load Comb 406
1 1.00 2 1.00 3 1.00 7 0.75 17 0.80 21 0.75 39 1.00 41 1.00
Load Comb 407
1 1.00 2 1.00 3 1.00 7 0.75 18 0.80 22 0.75 39 1.00 41 1.00
Load Comb 408
1 1.00 2 1.00 3 1.00 7 0.75 16 0.80 21 0.75 40 1.00 42 1.00
Load Comb 409
1 1.00 2 1.00 3 1.00 7 0.75 16 0.80 22 0.75 40 1.00 42 1.00
Load Comb 410
1 1.00 2 1.00 3 1.00 7 0.75 17 0.80 21 0.75 40 1.00 42 1.00
Load Comb 411
1 1.00 2 1.00 3 1.00 7 0.75 18 0.80 22 0.75 40 1.00 42 1.00
Load Comb 412
1 1.00 2 1.00 3 1.00 7 1.00 16 0.80 21 1.00 39 0.60 41 0.60
Load Comb 413
1 1.00 2 1.00 3 1.00 7 1.00 16 0.80 22 1.00 39 0.60 41 0.60
Load Comb 414
1 1.00 2 1.00 3 1.00 7 1.00 17 0.80 21 1.00 39 0.60 41 0.60
Load Comb 415
1 1.00 2 1.00 3 1.00 7 1.00 18 0.80 22 1.00 39 0.60 41 0.60
Load Comb 416
1 1.00 2 1.00 3 1.00 7 1.00 16 0.80 21 1.00 40 0.60 42 0.60
Load Comb 417
1 1.00 2 1.00 3 1.00 7 1.00 16 0.80 22 1.00 40 0.60 42 0.60
Load Comb 418
1 1.00 2 1.00 3 1.00 7 1.00 17 0.80 21 1.00 40 0.60 42 0.60
Load Comb 419
1 1.00 2 1.00 3 1.00 7 1.00 18 0.80 22 1.00 40 0.60 42 0.60
Load Comb 420
1 1.00 2 1.00 3 1.00 8 0.75 16 0.80 23 0.75 39 1.00 41 1.00
Load Comb 421
1 1.00 2 1.00 3 1.00 8 0.75 16 0.80 24 0.75 39 1.00 41 1.00
Load Comb 422
1 1.00 2 1.00 3 1.00 8 0.75 17 0.80 23 0.75 39 1.00 41 1.00
Load Comb 423
1 1.00 2 1.00 3 1.00 8 0.75 18 0.80 24 0.75 39 1.00 41 1.00
Load Comb 424
1 1.00 2 1.00 3 1.00 8 0.75 16 0.80 23 0.75 40 1.00 42 1.00
Load Comb 425
1 1.00 2 1.00 3 1.00 8 0.75 16 0.80 24 0.75 40 1.00 42 1.00
Load Comb 426
1 1.00 2 1.00 3 1.00 8 0.75 17 0.80 23 0.75 40 1.00 42 1.00
Load Comb 427
1 1.00 2 1.00 3 1.00 8 0.75 18 0.80 24 0.75 40 1.00 42 1.00
Load Comb 428
1 1.00 2 1.00 3 1.00 8 1.00 16 0.80 23 1.00 39 0.60 41 0.60
Load Comb 429
1 1.00 2 1.00 3 1.00 8 1.00 16 0.80 24 1.00 39 0.60 41 0.60
Load Comb 430
1 1.00 2 1.00 3 1.00 8 1.00 17 0.80 23 1.00 39 0.60 41 0.60
Load Comb 431
1 1.00 2 1.00 3 1.00 8 1.00 18 0.80 24 1.00 39 0.60 41 0.60
Load Comb 432
1 1.00 2 1.00 3 1.00 8 1.00 16 0.80 23 1.00 40 0.60 42 0.60
Load Comb 433
1 1.00 2 1.00 3 1.00 8 1.00 16 0.80 24 1.00 40 0.60 42 0.60
Load Comb 434
1 1.00 2 1.00 3 1.00 8 1.00 17 0.80 23 1.00 40 0.60 42 0.60
Load Comb 435
1 1.00 2 1.00 3 1.00 8 1.00 18 0.80 24 1.00 40 0.60 42 0.60
Load Comb 436
1 1.00 2 1.00 3 1.00 9 0.75 16 0.80 25 0.75 39 1.00 41 1.00
Load Comb 437
1 1.00 2 1.00 3 1.00 9 0.75 16 0.80 26 0.75 39 1.00 41 1.00
Load Comb 438
1 1.00 2 1.00 3 1.00 9 0.75 17 0.80 25 0.75 39 1.00 41 1.00
Load Comb 439
1 1.00 2 1.00 3 1.00 9 0.75 18 0.80 26 0.75 39 1.00 41 1.00
Load Comb 440
1 1.00 2 1.00 3 1.00 9 0.75 16 0.80 25 0.75 40 1.00 42 1.00
Load Comb 441
1 1.00 2 1.00 3 1.00 9 0.75 16 0.80 26 0.75 40 1.00 42 1.00
Load Comb 442
1 1.00 2 1.00 3 1.00 9 0.75 17 0.80 25 0.75 40 1.00 42 1.00
Load Comb 443
1 1.00 2 1.00 3 1.00 9 0.75 18 0.80 26 0.75 40 1.00 42 1.00
Load Comb 444
1 1.00 2 1.00 3 1.00 9 1.00 16 0.80 25 1.00 39 0.60 41 0.60
Load Comb 445
1 1.00 2 1.00 3 1.00 9 1.00 16 0.80 26 1.00 39 0.60 41 0.60
Load Comb 446
1 1.00 2 1.00 3 1.00 9 1.00 17 0.80 25 1.00 39 0.60 41 0.60
Load Comb 447
1 1.00 2 1.00 3 1.00 9 1.00 18 0.80 26 1.00 39 0.60 41 0.60
Load Comb 448
1 1.00 2 1.00 3 1.00 9 1.00 16 0.80 25 1.00 40 0.60 42 0.60
Load Comb 449
1 1.00 2 1.00 3 1.00 9 1.00 16 0.80 26 1.00 40 0.60 42 0.60
Load Comb 450
1 1.00 2 1.00 3 1.00 9 1.00 17 0.80 25 1.00 40 0.60 42 0.60
Load Comb 451
1 1.00 2 1.00 3 1.00 9 1.00 18 0.80 26 1.00 40 0.60 42 0.60
Load Comb 452
1 1.00 2 1.00 3 1.00 10 0.75 16 0.80 27 0.75 39 1.00 41 1.00
Load Comb 453
1 1.00 2 1.00 3 1.00 10 0.75 16 0.80 28 0.75 39 1.00 41 1.00
Load Comb 454
1 1.00 2 1.00 3 1.00 10 0.75 17 0.80 27 0.75 39 1.00 41 1.00
Load Comb 455
1 1.00 2 1.00 3 1.00 10 0.75 18 0.80 28 0.75 39 1.00 41 1.00
Load Comb 456
1 1.00 2 1.00 3 1.00 10 0.75 16 0.80 27 0.75 40 1.00 42 1.00
Load Comb 457
1 1.00 2 1.00 3 1.00 10 0.75 16 0.80 28 0.75 40 1.00 42 1.00
Load Comb 458
1 1.00 2 1.00 3 1.00 10 0.75 17 0.80 27 0.75 40 1.00 42 1.00
Load Comb 459
1 1.00 2 1.00 3 1.00 10 0.75 18 0.80 28 0.75 40 1.00 42 1.00
Load Comb 460
1 1.00 2 1.00 3 1.00 10 1.00 16 0.80 27 1.00 39 0.60 41 0.60
Load Comb 461
1 1.00 2 1.00 3 1.00 10 1.00 16 0.80 28 1.00 39 0.60 41 0.60
Load Comb 462
1 1.00 2 1.00 3 1.00 10 1.00 17 0.80 27 1.00 39 0.60 41 0.60
Load Comb 463
1 1.00 2 1.00 3 1.00 10 1.00 18 0.80 28 1.00 39 0.60 41 0.60
Load Comb 464
1 1.00 2 1.00 3 1.00 10 1.00 16 0.80 27 1.00 40 0.60 42 0.60
Load Comb 465
1 1.00 2 1.00 3 1.00 10 1.00 16 0.80 28 1.00 40 0.60 42 0.60
Load Comb 466
1 1.00 2 1.00 3 1.00 10 1.00 17 0.80 27 1.00 40 0.60 42 0.60
Load Comb 467
1 1.00 2 1.00 3 1.00 10 1.00 18 0.80 28 1.00 40 0.60 42 0.60
Load Comb 468
1 1.00 2 1.00 3 1.00 11 0.75 16 0.80 29 0.75 39 1.00 41 1.00
Load Comb 469
1 1.00 2 1.00 3 1.00 11 0.75 16 0.80 30 0.75 39 1.00 41 1.00
Load Comb 470
1 1.00 2 1.00 3 1.00 11 0.75 17 0.80 29 0.75 39 1.00 41 1.00
Load Comb 471
1 1.00 2 1.00 3 1.00 11 0.75 18 0.80 30 0.75 39 1.00 41 1.00
Load Comb 472
1 1.00 2 1.00 3 1.00 11 0.75 16 0.80 29 0.75 40 1.00 42 1.00
Load Comb 473
1 1.00 2 1.00 3 1.00 11 0.75 16 0.80 30 0.75 40 1.00 42 1.00
Load Comb 474
1 1.00 2 1.00 3 1.00 11 0.75 17 0.80 29 0.75 40 1.00 42 1.00
Load Comb 475
1 1.00 2 1.00 3 1.00 11 0.75 18 0.80 30 0.75 40 1.00 42 1.00
Load Comb 476
1 1.00 2 1.00 3 1.00 11 1.00 16 0.80 29 1.00 39 0.60 41 0.60
Load Comb 477
1 1.00 2 1.00 3 1.00 11 1.00 16 0.80 30 1.00 39 0.60 41 0.60
Load Comb 478
1 1.00 2 1.00 3 1.00 11 1.00 17 0.80 29 1.00 39 0.60 41 0.60
Load Comb 479
1 1.00 2 1.00 3 1.00 11 1.00 18 0.80 30 1.00 39 0.60 41 0.60
Load Comb 480
1 1.00 2 1.00 3 1.00 11 1.00 16 0.80 29 1.00 40 0.60 42 0.60
Load Comb 481
1 1.00 2 1.00 3 1.00 11 1.00 16 0.80 30 1.00 40 0.60 42 0.60
Load Comb 482
1 1.00 2 1.00 3 1.00 11 1.00 17 0.80 29 1.00 40 0.60 42 0.60
Load Comb 483
1 1.00 2 1.00 3 1.00 11 1.00 18 0.80 30 1.00 40 0.60 42 0.60
Load Comb 484
1 1.00 2 1.00 3 1.00 12 0.75 16 0.80 31 0.75 39 1.00 41 1.00
Load Comb 485
1 1.00 2 1.00 3 1.00 12 0.75 16 0.80 32 0.75 39 1.00 41 1.00
Load Comb 486
1 1.00 2 1.00 3 1.00 12 0.75 17 0.80 31 0.75 39 1.00 41 1.00
Load Comb 487
1 1.00 2 1.00 3 1.00 12 0.75 18 0.80 32 0.75 39 1.00 41 1.00
Load Comb 488
1 1.00 2 1.00 3 1.00 12 0.75 16 0.80 31 0.75 40 1.00 42 1.00
Load Comb 489
1 1.00 2 1.00 3 1.00 12 0.75 16 0.80 32 0.75 40 1.00 42 1.00
Load Comb 490
1 1.00 2 1.00 3 1.00 12 0.75 17 0.80 31 0.75 40 1.00 42 1.00
Load Comb 491
1 1.00 2 1.00 3 1.00 12 0.75 18 0.80 32 0.75 40 1.00 42 1.00
Load Comb 492
1 1.00 2 1.00 3 1.00 12 1.00 16 0.80 31 1.00 39 0.60 41 0.60
Load Comb 493
1 1.00 2 1.00 3 1.00 12 1.00 16 0.80 32 1.00 39 0.60 41 0.60
Load Comb 494
1 1.00 2 1.00 3 1.00 12 1.00 17 0.80 31 1.00 39 0.60 41 0.60
Load Comb 495
1 1.00 2 1.00 3 1.00 12 1.00 18 0.80 32 1.00 39 0.60 41 0.60
Load Comb 496
1 1.00 2 1.00 3 1.00 12 1.00 16 0.80 31 1.00 40 0.60 42 0.60
Load Comb 497
1 1.00 2 1.00 3 1.00 12 1.00 16 0.80 32 1.00 40 0.60 42 0.60
Load Comb 498
1 1.00 2 1.00 3 1.00 12 1.00 17 0.80 31 1.00 40 0.60 42 0.60
Load Comb 499
1 1.00 2 1.00 3 1.00 12 1.00 18 0.80 32 1.00 40 0.60 42 0.60
Load Comb 500
1 1.00 2 1.00 3 1.00 13 0.75 16 0.80 33 0.75 39 1.00 41 1.00
Load Comb 501
1 1.00 2 1.00 3 1.00 13 0.75 16 0.80 34 0.75 39 1.00 41 1.00
Load Comb 502
1 1.00 2 1.00 3 1.00 13 0.75 17 0.80 33 0.75 39 1.00 41 1.00
Load Comb 503
1 1.00 2 1.00 3 1.00 13 0.75 18 0.80 34 0.75 39 1.00 41 1.00
Load Comb 504
1 1.00 2 1.00 3 1.00 13 0.75 16 0.80 33 0.75 40 1.00 42 1.00
Load Comb 505
1 1.00 2 1.00 3 1.00 13 0.75 16 0.80 34 0.75 40 1.00 42 1.00
Load Comb 506
1 1.00 2 1.00 3 1.00 13 0.75 17 0.80 33 0.75 40 1.00 42 1.00
Load Comb 507
1 1.00 2 1.00 3 1.00 13 0.75 18 0.80 34 0.75 40 1.00 42 1.00
Load Comb 508
1 1.00 2 1.00 3 1.00 13 1.00 16 0.80 33 1.00 39 0.60 41 0.60
Load Comb 509
1 1.00 2 1.00 3 1.00 13 1.00 16 0.80 34 1.00 39 0.60 41 0.60
Load Comb 510
1 1.00 2 1.00 3 1.00 13 1.00 17 0.80 33 1.00 39 0.60 41 0.60
Load Comb 511
1 1.00 2 1.00 3 1.00 13 1.00 18 0.80 34 1.00 39 0.60 41 0.60
Load Comb 512
1 1.00 2 1.00 3 1.00 13 1.00 16 0.80 33 1.00 40 0.60 42 0.60
Load Comb 513
1 1.00 2 1.00 3 1.00 13 1.00 16 0.80 34 1.00 40 0.60 42 0.60
Load Comb 514
1 1.00 2 1.00 3 1.00 13 1.00 17 0.80 33 1.00 40 0.60 42 0.60
Load Comb 515
1 1.00 2 1.00 3 1.00 13 1.00 18 0.80 34 1.00 40 0.60 42 0.60
Load Comb 516
1 1.00 2 1.00 3 1.00 14 0.75 16 0.80 35 0.75 39 1.00 41 1.00
Load Comb 517
1 1.00 2 1.00 3 1.00 14 0.75 16 0.80 36 0.75 39 1.00 41 1.00
Load Comb 518
1 1.00 2 1.00 3 1.00 14 0.75 17 0.80 35 0.75 39 1.00 41 1.00
Load Comb 519
1 1.00 2 1.00 3 1.00 14 0.75 18 0.80 36 0.75 39 1.00 41 1.00
Load Comb 520
1 1.00 2 1.00 3 1.00 14 0.75 16 0.80 35 0.75 40 1.00 42 1.00
Load Comb 521
1 1.00 2 1.00 3 1.00 14 0.75 16 0.80 36 0.75 40 1.00 42 1.00
Load Comb 522
1 1.00 2 1.00 3 1.00 14 0.75 17 0.80 35 0.75 40 1.00 42 1.00
Load Comb 523
1 1.00 2 1.00 3 1.00 14 0.75 18 0.80 36 0.75 40 1.00 42 1.00
Load Comb 524
1 1.00 2 1.00 3 1.00 14 1.00 16 0.80 35 1.00 39 0.60 41 0.60
Load Comb 525
1 1.00 2 1.00 3 1.00 14 1.00 16 0.80 36 1.00 39 0.60 41 0.60
Load Comb 526
1 1.00 2 1.00 3 1.00 14 1.00 17 0.80 35 1.00 39 0.60 41 0.60
Load Comb 527
1 1.00 2 1.00 3 1.00 14 1.00 18 0.80 36 1.00 39 0.60 41 0.60
Load Comb 528
1 1.00 2 1.00 3 1.00 14 1.00 16 0.80 35 1.00 40 0.60 42 0.60
Load Comb 529
1 1.00 2 1.00 3 1.00 14 1.00 16 0.80 36 1.00 40 0.60 42 0.60
Load Comb 530
1 1.00 2 1.00 3 1.00 14 1.00 17 0.80 35 1.00 40 0.60 42 0.60
Load Comb 531
1 1.00 2 1.00 3 1.00 14 1.00 18 0.80 36 1.00 40 0.60 42 0.60
Load Comb 532
1 1.00 2 1.00 3 1.00 14 0.75 16 0.80 35 0.75 39 1.00 41 1.00
Load Comb 533
1 1.00 2 1.00 3 1.00 14 0.75 16 0.80 36 0.75 39 1.00 41 1.00
Load Comb 534
1 1.00 2 1.00 3 1.00 14 0.75 17 0.80 35 0.75 39 1.00 41 1.00
Load Comb 535
1 1.00 2 1.00 3 1.00 14 0.75 18 0.80 36 0.75 39 1.00 41 1.00
Load Comb 536
1 1.00 2 1.00 3 1.00 14 0.75 16 0.80 35 0.75 40 1.00 42 1.00
Load Comb 537
1 1.00 2 1.00 3 1.00 14 0.75 16 0.80 36 0.75 40 1.00 42 1.00
Load Comb 538
1 1.00 2 1.00 3 1.00 14 0.75 17 0.80 35 0.75 40 1.00 42 1.00
Load Comb 539
1 1.00 2 1.00 3 1.00 14 0.75 18 0.80 36 0.75 40 1.00 42 1.00
Load Comb 540
1 1.00 2 1.00 3 1.00 14 1.00 16 0.80 35 1.00 39 0.60 41 0.60
Load Comb 541
1 1.00 2 1.00 3 1.00 14 1.00 16 0.80 36 1.00 39 0.60 41 0.60
Load Comb 542
1 1.00 2 1.00 3 1.00 14 1.00 17 0.80 35 1.00 39 0.60 41 0.60
Load Comb 543
1 1.00 2 1.00 3 1.00 14 1.00 18 0.80 36 1.00 39 0.60 41 0.60
Load Comb 544
1 1.00 2 1.00 3 1.00 14 1.00 16 0.80 35 1.00 40 0.60 42 0.60
Load Comb 545
1 1.00 2 1.00 3 1.00 14 1.00 16 0.80 36 1.00 40 0.60 42 0.60
Load Comb 546
1 1.00 2 1.00 3 1.00 14 1.00 17 0.80 35 1.00 40 0.60 42 0.60
Load Comb 547
1 1.00 2 1.00 3 1.00 14 1.00 18 0.80 36 1.00 40 0.60 42 0.60
Load Comb 548
1 1.00 2 1.00 4 1.00
Load Comb 549
1 1.00 2 1.00 4 1.00 39 1.00 41 1.00
Load Comb 550
1 1.00 2 1.00 4 1.00 40 1.00 42 1.00
Load Comb 551
1 1.00 2 1.00 4 1.00 7 0.75 16 0.80 21 0.75 39 1.00 41 1.00
Load Comb 552
1 1.00 2 1.00 4 1.00 7 0.75 16 0.80 22 0.75 39 1.00 41 1.00
Load Comb 553
1 1.00 2 1.00 4 1.00 7 0.75 17 0.80 21 0.75 39 1.00 41 1.00
Load Comb 554
1 1.00 2 1.00 4 1.00 7 0.75 18 0.80 22 0.75 39 1.00 41 1.00
Load Comb 555
1 1.00 2 1.00 4 1.00 7 0.75 16 0.80 21 0.75 40 1.00 42 1.00
Load Comb 556
1 1.00 2 1.00 4 1.00 7 0.75 16 0.80 22 0.75 40 1.00 42 1.00
Load Comb 557
1 1.00 2 1.00 4 1.00 7 0.75 17 0.80 21 0.75 40 1.00 42 1.00
Load Comb 558
1 1.00 2 1.00 4 1.00 7 0.75 18 0.80 22 0.75 40 1.00 42 1.00
Load Comb 559
1 1.00 2 1.00 4 1.00 7 1.00 16 0.80 21 1.00 39 0.60 41 0.60
Load Comb 560
1 1.00 2 1.00 4 1.00 7 1.00 16 0.80 22 1.00 39 0.60 41 0.60
Load Comb 561
1 1.00 2 1.00 4 1.00 7 1.00 17 0.80 21 1.00 39 0.60 41 0.60
Load Comb 562
1 1.00 2 1.00 4 1.00 7 1.00 18 0.80 22 1.00 39 0.60 41 0.60
Load Comb 563
1 1.00 2 1.00 4 1.00 7 1.00 16 0.80 21 1.00 40 0.60 42 0.60
Load Comb 564
1 1.00 2 1.00 4 1.00 7 1.00 16 0.80 22 1.00 40 0.60 42 0.60
Load Comb 565
1 1.00 2 1.00 4 1.00 7 1.00 17 0.80 21 1.00 40 0.60 42 0.60
Load Comb 566
1 1.00 2 1.00 4 1.00 7 1.00 18 0.80 22 1.00 40 0.60 42 0.60
Load Comb 567
1 1.00 2 1.00 4 1.00 8 0.75 16 0.80 23 0.75 39 1.00 41 1.00
Load Comb 568
1 1.00 2 1.00 4 1.00 8 0.75 16 0.80 24 0.75 39 1.00 41 1.00
Load Comb 569
1 1.00 2 1.00 4 1.00 8 0.75 17 0.80 23 0.75 39 1.00 41 1.00
Load Comb 570
1 1.00 2 1.00 4 1.00 8 0.75 18 0.80 24 0.75 39 1.00 41 1.00
Load Comb 571
1 1.00 2 1.00 4 1.00 8 0.75 16 0.80 23 0.75 40 1.00 42 1.00
Load Comb 572
1 1.00 2 1.00 4 1.00 8 0.75 16 0.80 24 0.75 40 1.00 42 1.00
Load Comb 573
1 1.00 2 1.00 4 1.00 8 0.75 17 0.80 23 0.75 40 1.00 42 1.00
Load Comb 574
1 1.00 2 1.00 4 1.00 8 0.75 18 0.80 24 0.75 40 1.00 42 1.00
Load Comb 575
1 1.00 2 1.00 4 1.00 8 1.00 16 0.80 23 1.00 39 0.60 41 0.60
Load Comb 576
1 1.00 2 1.00 4 1.00 8 1.00 16 0.80 24 1.00 39 0.60 41 0.60
Load Comb 577
1 1.00 2 1.00 4 1.00 8 1.00 17 0.80 23 1.00 39 0.60 41 0.60
Load Comb 578
1 1.00 2 1.00 4 1.00 8 1.00 18 0.80 24 1.00 39 0.60 41 0.60
Load Comb 579
1 1.00 2 1.00 4 1.00 8 1.00 16 0.80 23 1.00 40 0.60 42 0.60
Load Comb 580
1 1.00 2 1.00 4 1.00 8 1.00 16 0.80 24 1.00 40 0.60 42 0.60
Load Comb 581
1 1.00 2 1.00 4 1.00 8 1.00 17 0.80 23 1.00 40 0.60 42 0.60
Load Comb 582
1 1.00 2 1.00 4 1.00 8 1.00 18 0.80 24 1.00 40 0.60 42 0.60
Load Comb 583
1 1.00 2 1.00 4 1.00 9 0.75 16 0.80 25 0.75 39 1.00 41 1.00
Load Comb 584
1 1.00 2 1.00 4 1.00 9 0.75 16 0.80 26 0.75 39 1.00 41 1.00
Load Comb 585
1 1.00 2 1.00 4 1.00 9 0.75 17 0.80 25 0.75 39 1.00 41 1.00
Load Comb 586
1 1.00 2 1.00 4 1.00 9 0.75 18 0.80 26 0.75 39 1.00 41 1.00
Load Comb 587
1 1.00 2 1.00 4 1.00 9 0.75 16 0.80 25 0.75 40 1.00 42 1.00
Load Comb 588
1 1.00 2 1.00 4 1.00 9 0.75 16 0.80 26 0.75 40 1.00 42 1.00
Load Comb 589
1 1.00 2 1.00 4 1.00 9 0.75 17 0.80 25 0.75 40 1.00 42 1.00
Load Comb 590
1 1.00 2 1.00 4 1.00 9 0.75 18 0.80 26 0.75 40 1.00 42 1.00
Load Comb 591
1 1.00 2 1.00 4 1.00 9 1.00 16 0.80 25 1.00 39 0.60 41 0.60
Load Comb 592
1 1.00 2 1.00 4 1.00 9 1.00 16 0.80 26 1.00 39 0.60 41 0.60
Load Comb 593
1 1.00 2 1.00 4 1.00 9 1.00 17 0.80 25 1.00 39 0.60 41 0.60
Load Comb 594
1 1.00 2 1.00 4 1.00 9 1.00 18 0.80 26 1.00 39 0.60 41 0.60
Load Comb 595
1 1.00 2 1.00 4 1.00 9 1.00 16 0.80 25 1.00 40 0.60 42 0.60
Load Comb 596
1 1.00 2 1.00 4 1.00 9 1.00 16 0.80 26 1.00 40 0.60 42 0.60
Load Comb 597
1 1.00 2 1.00 4 1.00 9 1.00 17 0.80 25 1.00 40 0.60 42 0.60
Load Comb 598
1 1.00 2 1.00 4 1.00 9 1.00 18 0.80 26 1.00 40 0.60 42 0.60
Load Comb 599
1 1.00 2 1.00 4 1.00 10 0.75 16 0.80 27 0.75 39 1.00 41 1.00
Load Comb 600
1 1.00 2 1.00 4 1.00 10 0.75 16 0.80 28 0.75 39 1.00 41 1.00
Load Comb 601
1 1.00 2 1.00 4 1.00 10 0.75 17 0.80 27 0.75 39 1.00 41 1.00
Load Comb 602
1 1.00 2 1.00 4 1.00 10 0.75 18 0.80 28 0.75 39 1.00 41 1.00
Load Comb 603
1 1.00 2 1.00 4 1.00 10 0.75 16 0.80 27 0.75 40 1.00 42 1.00
Load Comb 604
1 1.00 2 1.00 4 1.00 10 0.75 16 0.80 28 0.75 40 1.00 42 1.00
Load Comb 605
1 1.00 2 1.00 4 1.00 10 0.75 17 0.80 27 0.75 40 1.00 42 1.00
Load Comb 606
1 1.00 2 1.00 4 1.00 10 0.75 18 0.80 28 0.75 40 1.00 42 1.00
Load Comb 607
1 1.00 2 1.00 4 1.00 10 1.00 16 0.80 27 1.00 39 0.60 41 0.60
Load Comb 608
1 1.00 2 1.00 4 1.00 10 1.00 16 0.80 28 1.00 39 0.60 41 0.60
Load Comb 609
1 1.00 2 1.00 4 1.00 10 1.00 17 0.80 27 1.00 39 0.60 41 0.60
Load Comb 610
1 1.00 2 1.00 4 1.00 10 1.00 18 0.80 28 1.00 39 0.60 41 0.60
Load Comb 611
1 1.00 2 1.00 4 1.00 10 1.00 16 0.80 27 1.00 40 0.60 42 0.60
Load Comb 612
1 1.00 2 1.00 4 1.00 10 1.00 16 0.80 28 1.00 40 0.60 42 0.60
Load Comb 613
1 1.00 2 1.00 4 1.00 10 1.00 17 0.80 27 1.00 40 0.60 42 0.60
Load Comb 614
1 1.00 2 1.00 4 1.00 10 1.00 18 0.80 28 1.00 40 0.60 42 0.60
Load Comb 615
1 1.00 2 1.00 4 1.00 11 0.75 16 0.80 29 0.75 39 1.00 41 1.00
Load Comb 616
1 1.00 2 1.00 4 1.00 11 0.75 16 0.80 30 0.75 39 1.00 41 1.00
Load Comb 617
1 1.00 2 1.00 4 1.00 11 0.75 17 0.80 29 0.75 39 1.00 41 1.00
Load Comb 618
1 1.00 2 1.00 4 1.00 11 0.75 18 0.80 30 0.75 39 1.00 41 1.00
Load Comb 619
1 1.00 2 1.00 4 1.00 11 0.75 16 0.80 29 0.75 40 1.00 42 1.00
Load Comb 620
1 1.00 2 1.00 4 1.00 11 0.75 16 0.80 30 0.75 40 1.00 42 1.00
Load Comb 621
1 1.00 2 1.00 4 1.00 11 0.75 17 0.80 29 0.75 40 1.00 42 1.00
Load Comb 622
1 1.00 2 1.00 4 1.00 11 0.75 18 0.80 30 0.75 40 1.00 42 1.00
Load Comb 623
1 1.00 2 1.00 4 1.00 11 1.00 16 0.80 29 1.00 39 0.60 41 0.60
Load Comb 624
1 1.00 2 1.00 4 1.00 11 1.00 16 0.80 30 1.00 39 0.60 41 0.60
Load Comb 625
1 1.00 2 1.00 4 1.00 11 1.00 17 0.80 29 1.00 39 0.60 41 0.60
Load Comb 626
1 1.00 2 1.00 4 1.00 11 1.00 18 0.80 30 1.00 39 0.60 41 0.60
Load Comb 627
1 1.00 2 1.00 4 1.00 11 1.00 16 0.80 29 1.00 40 0.60 42 0.60
Load Comb 628
1 1.00 2 1.00 4 1.00 11 1.00 16 0.80 30 1.00 40 0.60 42 0.60
Load Comb 629
1 1.00 2 1.00 4 1.00 11 1.00 17 0.80 29 1.00 40 0.60 42 0.60
Load Comb 630
1 1.00 2 1.00 4 1.00 11 1.00 18 0.80 30 1.00 40 0.60 42 0.60
Load Comb 631
1 1.00 2 1.00 4 1.00 12 0.75 16 0.80 31 0.75 39 1.00 41 1.00
Load Comb 632
1 1.00 2 1.00 4 1.00 12 0.75 16 0.80 32 0.75 39 1.00 41 1.00
Load Comb 633
1 1.00 2 1.00 4 1.00 12 0.75 17 0.80 31 0.75 39 1.00 41 1.00
Load Comb 634
1 1.00 2 1.00 4 1.00 12 0.75 18 0.80 32 0.75 39 1.00 41 1.00
Load Comb 635
1 1.00 2 1.00 4 1.00 12 0.75 16 0.80 31 0.75 40 1.00 42 1.00
Load Comb 636
1 1.00 2 1.00 4 1.00 12 0.75 16 0.80 32 0.75 40 1.00 42 1.00
Load Comb 637
1 1.00 2 1.00 4 1.00 12 0.75 17 0.80 31 0.75 40 1.00 42 1.00
Load Comb 638
1 1.00 2 1.00 4 1.00 12 0.75 18 0.80 32 0.75 40 1.00 42 1.00
Load Comb 639
1 1.00 2 1.00 4 1.00 12 1.00 16 0.80 31 1.00 39 0.60 41 0.60
Load Comb 640
1 1.00 2 1.00 4 1.00 12 1.00 16 0.80 32 1.00 39 0.60 41 0.60
Load Comb 641
1 1.00 2 1.00 4 1.00 12 1.00 17 0.80 31 1.00 39 0.60 41 0.60
Load Comb 642
1 1.00 2 1.00 4 1.00 12 1.00 18 0.80 32 1.00 39 0.60 41 0.60
Load Comb 643
1 1.00 2 1.00 4 1.00 12 1.00 16 0.80 31 1.00 40 0.60 42 0.60
Load Comb 644
1 1.00 2 1.00 4 1.00 12 1.00 16 0.80 32 1.00 40 0.60 42 0.60
Load Comb 645
1 1.00 2 1.00 4 1.00 12 1.00 17 0.80 31 1.00 40 0.60 42 0.60
Load Comb 646
1 1.00 2 1.00 4 1.00 12 1.00 18 0.80 32 1.00 40 0.60 42 0.60
Load Comb 647
1 1.00 2 1.00 4 1.00 13 0.75 16 0.80 33 0.75 39 1.00 41 1.00
Load Comb 648
1 1.00 2 1.00 4 1.00 13 0.75 16 0.80 34 0.75 39 1.00 41 1.00
Load Comb 649
1 1.00 2 1.00 4 1.00 13 0.75 17 0.80 33 0.75 39 1.00 41 1.00
Load Comb 650
1 1.00 2 1.00 4 1.00 13 0.75 18 0.80 34 0.75 39 1.00 41 1.00
Load Comb 651
1 1.00 2 1.00 4 1.00 13 0.75 16 0.80 33 0.75 40 1.00 42 1.00
Load Comb 652
1 1.00 2 1.00 4 1.00 13 0.75 16 0.80 34 0.75 40 1.00 42 1.00
Load Comb 653
1 1.00 2 1.00 4 1.00 13 0.75 17 0.80 33 0.75 40 1.00 42 1.00
Load Comb 654
1 1.00 2 1.00 4 1.00 13 0.75 18 0.80 34 0.75 40 1.00 42 1.00
Load Comb 655
1 1.00 2 1.00 4 1.00 14 1.00 16 0.80 33 1.00 39 0.60 41 0.60
Load Comb 656
1 1.00 2 1.00 4 1.00 14 1.00 16 0.80 34 1.00 39 0.60 41 0.60
Load Comb 657
1 1.00 2 1.00 4 1.00 14 1.00 17 0.80 33 1.00 39 0.60 41 0.60
Load Comb 658
1 1.00 2 1.00 4 1.00 14 1.00 18 0.80 34 1.00 39 0.60 41 0.60
Load Comb 659
1 1.00 2 1.00 4 1.00 14 1.00 16 0.80 33 1.00 40 0.60 42 0.60
Load Comb 660
1 1.00 2 1.00 4 1.00 14 1.00 16 0.80 34 1.00 40 0.60 42 0.60
Load Comb 661
1 1.00 2 1.00 4 1.00 14 1.00 17 0.80 33 1.00 40 0.60 42 0.60
Load Comb 662
1 1.00 2 1.00 4 1.00 14 1.00 18 0.80 34 1.00 40 0.60 42 0.60
Load Comb 663
1 1.00 2 1.00 4 1.00 14 0.75 16 0.80 35 0.75 39 1.00 41 1.00
Load Comb 664
1 1.00 2 1.00 4 1.00 14 0.75 16 0.80 36 0.75 39 1.00 41 1.00
Load Comb 665
1 1.00 2 1.00 4 1.00 14 0.75 17 0.80 35 0.75 39 1.00 41 1.00
Load Comb 666
1 1.00 2 1.00 4 1.00 14 0.75 18 0.80 36 0.75 39 1.00 41 1.00
Load Comb 667
1 1.00 2 1.00 4 1.00 14 0.75 16 0.80 35 0.75 40 1.00 42 1.00
Load Comb 668
1 1.00 2 1.00 4 1.00 14 0.75 16 0.80 36 0.75 40 1.00 42 1.00
Load Comb 669
1 1.00 2 1.00 4 1.00 14 0.75 17 0.80 35 0.75 40 1.00 42 1.00
Load Comb 670
1 1.00 2 1.00 4 1.00 14 0.75 18 0.80 36 0.75 40 1.00 42 1.00
Load Comb 671
1 1.00 2 1.00 4 1.00 14 1.00 16 0.80 35 1.00 39 0.60 41 0.60
Load Comb 672
1 1.00 2 1.00 4 1.00 14 1.00 16 0.80 36 1.00 39 0.60 41 0.60
Load Comb 673
1 1.00 2 1.00 4 1.00 14 1.00 17 0.80 35 1.00 39 0.60 41 0.60
Load Comb 674
1 1.00 2 1.00 4 1.00 14 1.00 18 0.80 36 1.00 39 0.60 41 0.60
Load Comb 675
1 1.00 2 1.00 4 1.00 14 1.00 16 0.80 35 1.00 40 0.60 42 0.60
Load Comb 676
1 1.00 2 1.00 4 1.00 14 1.00 16 0.80 36 1.00 40 0.60 42 0.60
Load Comb 677
1 1.00 2 1.00 4 1.00 14 1.00 17 0.80 35 1.00 40 0.60 42 0.60
Load Comb 678
1 1.00 2 1.00 4 1.00 14 1.00 18 0.80 36 1.00 40 0.60 42 0.60
Load Comb 679
1 1.00 2 1.00 4 1.00 14 0.75 16 0.80 35 0.75 39 1.00 41 1.00
Load Comb 680
1 1.00 2 1.00 4 1.00 14 0.75 16 0.80 36 0.75 39 1.00 41 1.00
Load Comb 681
1 1.00 2 1.00 4 1.00 14 0.75 17 0.80 35 0.75 39 1.00 41 1.00
Load Comb 682
1 1.00 2 1.00 4 1.00 14 0.75 18 0.80 36 0.75 39 1.00 41 1.00
Load Comb 683
1 1.00 2 1.00 4 1.00 14 0.75 16 0.80 35 0.75 40 1.00 42 1.00
Load Comb 684
1 1.00 2 1.00 4 1.00 14 0.75 16 0.80 36 0.75 40 1.00 42 1.00
Load Comb 685
1 1.00 2 1.00 4 1.00 14 0.75 17 0.80 35 0.75 40 1.00 42 1.00
Load Comb 686
1 1.00 2 1.00 4 1.00 14 0.75 18 0.80 36 0.75 40 1.00 42 1.00
Load Comb 687
1 1.00 2 1.00 4 1.00 14 1.00 16 0.80 35 1.00 39 0.60 41 0.60
Load Comb 688
1 1.00 2 1.00 4 1.00 14 1.00 16 0.80 36 1.00 39 0.60 41 0.60
Load Comb 689
1 1.00 2 1.00 4 1.00 14 1.00 17 0.80 35 1.00 39 0.60 41 0.60
Load Comb 690
1 1.00 2 1.00 4 1.00 14 1.00 18 0.80 36 1.00 39 0.60 41 0.60
Load Comb 691
1 1.00 2 1.00 4 1.00 14 1.00 16 0.80 35 1.00 40 0.60 42 0.60
Load Comb 692
1 1.00 2 1.00 4 1.00 14 1.00 16 0.80 36 1.00 40 0.60 42 0.60
Load Comb 693
1 1.00 2 1.00 4 1.00 14 1.00 17 0.80 35 1.00 40 0.60 42 0.60
Load Comb 694
1 1.00 2 1.00 4 1.00 14 1.00 18 0.80 36 1.00 40 0.60 42 0.60
****************LOAD Combination For Crack Width & Permanent Stress Check
Load Comb 701
1 1.00 2 1.00 3 1.00 39 0.5
Load Comb 702
1 1.00 2 1.00 4 1.00 39 0.5
Load Comb 703
1 1.00 2 1.00 3 1.00 40 0.5
Load Comb 704
1 1.00 2 1.00 4 1.00 40 0.5
****************LOAD Combination For Deflection Check
Load Comb 801
1 1.00 2 1.00 3 1.00
Load Comb 802
1 1.00 2 1.00 3 1.00 39 0.6 41 0.6
Load Comb 803
1 1.00 2 1.00 3 1.00 40 0.6 42 0.6
Load Comb 804
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 805
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 806
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 807
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 808
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 809
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 810
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 811
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 812
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 813
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 814
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 815
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 816
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 817
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 818
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 819
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 820
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 821
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 1.00 41 1.00
Load Comb 822
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 1.00 41 1.00
Load Comb 823
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 1.00 41 1.00
Load Comb 824
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 825
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 826
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 827
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 828
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 829
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 830
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 831
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 832
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 833
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 834
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 835
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 836
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 837
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 838
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 839
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 840
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 841
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 842
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 843
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 844
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 845
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 846
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 847
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 848
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 849
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 850
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 851
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 852
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 853
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 854
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 855
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 856
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 857
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 858
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 859
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 860
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 861
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 862
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 863
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 864
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 865
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 866
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 867
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 868
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 869
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 870
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 871
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 872
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 873
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 874
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 875
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 876
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 877
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 878
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 879
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 880
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 881
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 882
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 883
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 884
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 885
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 886
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 887
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 888
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 889
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 890
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 891
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 892
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 893
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 894
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 895
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 896
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 897
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 898
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 899
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 900
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 901
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 902
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 903
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 904
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 905
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 906
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 907
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 908
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 909
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 910
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 911
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 912
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 913
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 914
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 915
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 916
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 917
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 918
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 919
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 920
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 921
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 922
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 923
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 924
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 925
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 926
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 927
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 928
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 929
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 930
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 931
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 932
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 933
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 934
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 935
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 936
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 937
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 938
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 939
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 940
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 941
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 942
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 943
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 944
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 945
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 946
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 947
1 1.00 2 1.00 3 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 948
1 1.00 2 1.00 4 1.00
Load Comb 949
1 1.00 2 1.00 4 1.00 39 0.6 41 0.6
Load Comb 950
1 1.00 2 1.00 4 1.00 39 0.6 41 0.6
Load Comb 951
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 952
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 953
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 954
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 955
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 956
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 957
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 958
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 959
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 960
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 961
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 962
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 963
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 964
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 965
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 966
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 967
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 968
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 1.00 41 1.00
Load Comb 969
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 1.00 41 1.00
Load Comb 970
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 1.00 41 1.00
Load Comb 971
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 972
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 973
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 974
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 975
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 976
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 977
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 978
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 979
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 980
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 981
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 982
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 983
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 984
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 985
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 986
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 987
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 988
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 989
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 990
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 991
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 992
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 993
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 994
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 995
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 996
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 997
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 998
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 999
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 1000
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 1001
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 1002
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 1003
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 1004
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 1005
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 1006
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 1007
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 1008
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 1009
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 1010
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 1011
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 1012
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 1013
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 1014
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 1015
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 1016
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 1017
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 1018
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 1019
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 1020
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 1021
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 1022
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 1023
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 1024
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 1025
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 9 0.5 41 0.5
Load Comb 1026
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 1027
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 1028
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 1029
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 1030
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 1031
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 1032
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 1033
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 1034
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 1035
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 1036
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 1037
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 1038
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 1039
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 1040
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 1041
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 1042
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 1043
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 1044
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 1045
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 1046
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 1047
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 1048
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 1049
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 9 0.6 41 0.6
Load Comb 1050
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 1051
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 1052
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 1053
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 1054
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 1055
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 1056
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 1057
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 1058
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 1059
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 1060
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 1061
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 1062
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 1063
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 1064
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 1065
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 1066
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 1067
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 1068
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 1069
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 1070
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 1071
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 1072
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 1073
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 1074
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 1075
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 1076
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 1077
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 1078
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 1079
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 1080
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 1081
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 1082
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.6 41 0.6
Load Comb 1083
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 1084
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 1085
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 1086
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.6 42 0.6
Load Comb 1087
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 1088
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 1089
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 1090
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 39 0.5 41 0.5
Load Comb 1091
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 1092
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 1093
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
Load Comb 1094
1 1.00 2 1.00 4 1.00 7 0.2 16 0 21 0.2 40 0.5 42 0.5
PERFORM ANALYSIS
LOAD LIST 201 TO 346
******TOP SLAB
PRINT MAXFORCE ENVELOPE NSECTION 3 LIST 20 11 -
19 12 -
18 13 -
14 17 -
16 15
*********VERTICAL WALL (OUTER)
PRINT MAXFORCE ENVELOPE NSECTION 3 LIST 30 40 29 39 28 38 27 37 26 36 -
25 35 24 34 23 33 22 32 21 31
********BOTTOM SLAB
PRINT MAXFORCE ENVELOPE NSECTION 3 LIST 10 1 9 2 8 3 7 4 6 5
LOAD LIST 401 TO 694
******TOP SLAB
PRINT MAXFORCE ENVELOPE NSECTION 3 LIST 20 11 -
19 12 -
18 13 -
14 17 -
16 15
*********VERTICAL WALL (OUTER)
PRINT MAXFORCE ENVELOPE NSECTION 3 LIST 30 40 29 39 28 38 27 37 26 36 -
25 35 24 34 23 33 22 32 21 31
********BOTTOM SLAB
PRINT MAXFORCE ENVELOPE NSECTION 3 LIST 10 1 9 2 8 3 7 4 6 5
LOAD LIST 701 TO 704
******TOP SLAB
PRINT MAXFORCE ENVELOPE NSECTION 3 LIST 20 11 -
19 12 -
18 13 -
14 17 -
16 15
*********VERTICAL WALL (OUTER)
PRINT MAXFORCE ENVELOPE NSECTION 3 LIST 30 40 29 39 28 38 27 37 26 36 -
25 35 24 34 23 33 22 32 21 31
********BOTTOM SLAB
PRINT MAXFORCE ENVELOPE NSECTION 3 LIST 10 1 9 2 8 3 7 4 6 5
LOAD LIST 801 TO 1094
******TOP SLAB
PRINT MAXFORCE ENVELOPE NSECTION 3 LIST 20 11 -
19 12 -
18 13 -
14 17 -
16 15
*********VERTICAL WALL (OUTER)
PRINT MAXFORCE ENVELOPE NSECTION 3 LIST 30 40 29 39 28 38 27 37 26 36 -
25 35 24 34 23 33 22 32 21 31
********BOTTOM SLAB
PRINT MAXFORCE ENVELOPE NSECTION 3 LIST 10 1 9 2 8 3 7 4 6 5
FINISH