DOC. NO.: GEN -CIV-SPC-0004 REV.: B PAGE 1 OF 14 BASIC DESIGN SPECIFICATION FOR ARCHITECTURAL FINISHING 8 | ssxorovmmom | casms] So | | wx REV. DESCRIPTION DATE PREP’D ‘CHK'D: REVD ‘APP’D:BASIC DESIGN DOC. NO.: GEN -CIV-SPC-0004 REV. B PAGE 2 OF 14 CONTENT 1.0 GENERAL .. 4.1 Scope 1.2 References... 1.3 Definitions and Abbreviations .. 1.4 Site Condition: 2.0 MAJOR DESIGN PARAMETER. 3.0 ARCHITECHURAL CONFORMATION AND DECORATION OF BUILDINGS .. 3.1 Building design ight steel structure. ing doeign - reinforced concrete frame.. 3.3 Suspended Ceilings. 3.4 Surface Fi hes .. 3.5 Stairs, Ramps and Balustrading 4.0 ENGINEERING PRACTICE LIST.Aan ope BASIC DESIGN DOC. NO.: GEN -CIV-SPC-0004 REV. B PAGE 3 OF 13 1.0 GENERAL 1.4 Scope This Specification defines minimum architectural design, construction and other performance Tequirements for buildings to be constructed. Specifications is based on Intemational Standards and Codes of Practice. The contents of this Specification shall be adopted by the CONTRACTOR and further developed during detailed engineering phases of the project. The external decoration Colors of the buildings shall comply with HFY-GEN-CIV-SPC-0016 Specification for unified architectural practice 1.2 References Civil design for this project shall be carried out in accordance with American codes and standards listed here below. The latest edition of the following codes and standards shall be followed as a minimum. requirement, except as superseded herein. American National Standards Institute (ANSI) + ANSI A108 American National Standard Specifications for Install of Ceramic Tile + ANSI A118.1 American National Standard Specifications for Dry-set Portland Cement Mortar + ANSI A118.3 American National Standard Specifications for Chemical-resistant, Water- cleanable Tile-setting and grouting Epoxy and Water Cleanable Tile-setting Epoxy Adhesive + ANSI A118.4 American National Standard Specifications for Latex-portland Cement Mortar + ANSI A118.6 American National Standard Specifications for Cement Grouts for Tile Installation + ANSI A118. American National Standard Specifications for Modified Epoxy Emulsion Mortar/Grout + ANSI A136.1 American National Standard Specifications for Organic Adhesives for Installation of Ceramic Tile + ANSI A1264.1, Safety Requirements for Workplace Floor and Wall Openings, Stairs and Railing Systems + ANSI 297.1, Glazing Materials Used in Buildings, Safety Performance Specifications and Methods of Test American Concrete Institute (AC!) + ACI 318 Building Code Requirements ‘or Structural Concrete, and CommentaryAan ope BASIC DESIGN DOC. NO.: GEN -CIV-SPC-0004 REV. B PAGE 4 OF 13 + ACI 315 detailing Manual for Reinforced Concrete + ACI 530 Building Code Requirements for Masonry Structures + ACI 530.1 Specifications for Masonry Structures American Society of Civil Engineers (ASCE) + ASCE Design of Blast Resistant Buildings in Petrochemical Facilities + ASCE 7 Minimum Design Loads for buildings and other Structures American Institute of Steel Construction (AISC) + AISC 341 Seismic Provisions for Structural Steel Buildings + AISC 360 Specifications for Structural Steel Buildings Is (ASTM) American Society for Testing and Materi + ASTM C 22/C 22M Specification for Gypsum. + ASTM C 33 Specification for Concrete Aggregates + ASTM C 56 Specification for Concrete Brick + ASTM C 91 Specification for Masonry Cement + ASTM C 94/C 94M Specification for Ready-mixed Concrete + ASTM C 150 Specification for Portland Cement + ASTM C 206, Standard Specification for Finishing Hydrated Lime + ASTM C 476, Standard Specification for Grout for Masonry + ASTM C 840, Standard Specification for Application and Finishing of Gypsum Board + ASTM C 1396/C 1396M, Standard Specification for Gypsum Board National Fire Protection Association (NFPA) “NFPA1 — Uniform Fire Code + NFPA 101 Life Safety Code + NFPA 101A Guide on Alternative Approaches to Life Safety + NFPA 101B Code for Means of Egress for Buildings and Structures + NFPA 220 Standard on Types of Building Construction + NFPA252 Standard Methods of Fire Tests of Door Assemblies + NFPA257 Standard on Fire Tests for window and Glass Block Assemblies + NFPA 5000 Building Construction and Safety CodeAan= a wr- BASIC DESIGN DOC. NO.: GEN -CIV-SPC-0004 REV. B PAGE 5 OF 13 Uniform Building Code (UBC97) International Building Code (IBC) + Chapter 3 Use And Occupancy Classification + Chapter 5 General Building Height And Areas + Chapter 6 Types Of Construction + Chapter 7 Fire-Resistance-Rated Construction + Chapter 8 Interior Finishes + Chapter 9 Fire Protection systems + Chapter 10 Means Of Egress + Chapter 12 Interior Environment + Chapter 14 Exterior Walls + Chapter 15 Roof Assemblies And Roottop Structure + Chapter 19 Concrete + Chapter 20 Aluminum + Chapter 21 Masonry + Chapter 22 Steel + Chapter 23 Wood * Chapter 24 Glass And Glazing + Chapter 25 Gypsum Board And Plaster + Chapter 26 Plastic 1.3. Definitions and Abbreviations 1.3.1. Definitions WORD MEANING COMPANY. PetroChina Intemational Iraq FZE Iraq Branch ‘The organization selected and entrusted by COMPANY to perform the CONTRACTOR Engineering, Procurement, Construction, Start-up, pre-Commissioning and Commissioning of the Project. ‘The party who is in charge of awarding agreement on behalf of PURCHASER COMPANY / CONTRACTOR for the supply of goods and services in ‘connection with the work. VENDOR! SUPPLIERY | The party to the contract and/or purchase order which has undertaken SUBCONTRACTOR _ | the obligation to supply the goods andlor services which are orderedAan ca ios wr- BASIC DESIGN DOC. NO.: GEN -CIV-SPC-0004 REV. B PAGE 6 OF 13 WORD MEANING and specified herein Shall Indicates a mandatory requirement “Shoula Indicates a strong recommendation to comply with the requirements of this document 1.4 Site Conditions The following are the climatic conditions for all equipment and facilites. Altitude mas. [056 ‘Atmospheric Pressure Pa__[ 102 Max Temp. e 55 Wet Bulb Temp c 22.2 (GPSA 11-30) Dry Bulb Temp. © 42.2 (GPSA 11-26) Max. Metal temp. by sun ahine | © 20 Min. Temp. c 2 Max. Speed Wind ms 40 Prevailing Direction Wind | (winter) | NW-SE Prevailing Direction Wind | (summer) | NW-SE Max. Relative Humidity 80% Min, Relative Humidity 25% Rainfall mma | 17.4 4 -hour Rainfall mm (at Under Ground ¢ 45 in winter (1.2.1.6 m) Ground Temp. 33.6 in summer (1m) Seismic Zone 28 Evaporation Rate mma | 30544 2.0 MAJOR DESIGN PARAMETER 2.1 Design working life of buildings: Design working life of light steel! structure is 25 years, and reinforced concrete frame structure is 50 years.Aan= a wr- BASIC DESIGN DOC. NO.: GEN -CIV-SPC-0004 REV. B PAGE 7 OF 13 2.2 Building Fire Protection Fire zone: Every building is a fire compartment, the area of which is showed in unit drawing. Each building has two or three safety exits. The building’s fire resistance rating: The building's fire resistance rating shall apply with IBC. The fire resistance rating of all buildings is not less than grade Type | B. The fire resistance ratings of major structural component should be as the following table. TABLE 4.3 FIRE RESISTANCE RATING FOR BUILDING ELEMENTS (hours) ‘Construction Type Building Element Name Typeth pe Te Primary Structural Frame 3 2 (Including columns, beams, girders, trusses, ete.) Exterior 3 2 Bearing Walls Exterior = 2 Nonbearing walls and partitions- Exterior Not less than 4 Nonbearing walls and partitions- Interior 0 0 Floor construction and associated 2 2 ‘secondary members Roof construction and associated 18 7 ‘secondary members Corridor 7 7 Note: Roof supports: Fire-resistance ratings of primary structural frame and bearing walls are permitted to be reduced by 1 hour where supporting a roof only. Fire doors and fire windows: Fire-resistance rating of steel fire door and fire window is at least 1.5 hour rating according to the rating of the wall. All fire doors should have fixed door closer, Double-leaf fire doors need door closer and gravity arm door selector, hold-open fire doors need signal control close and feedback device. The fire door satisfies NFPA 252 (the Standard Methods of Fire Tests of Door Assemblies). The fire window satisfies NFPA 257 (the Standard on Fire Tests for window and Glass Block Assemblies). 3.0 ARCHITECHURAL CONFORMATION AND DECORATION OF BUILDINGS The selection of building materials should be optimized according to the local natural (climate etc), and social conditions (construction, etc). Local resources should be used as much as possible. The durability, practical principles and the fire and explosion prevention requirements must be followed.strength.Aan ope BASIC DESIGN DOC. NO.: GEN -CIV-SPC-0004 REV. B PAGE 8 OF 13 3.1 Building design - light steel structure @) Roofing Sandwich plate is used for roofing. The base material is aluminium galvanized color profiled steel sheet which chip with glass fibre of not less than 100mm thick and the bulk density is not less than 60Kg/ m°. The colour profiled steel sheet is more than 0.6mm thick. Yield strength of steel plate is 345MPathe weight of double plated Al-Zn is 180g/ m*, fixed with setf-tapping screw. Fasteners should adapt to the fixed components. b) Wall: Sandwich plate is used for exterior walls. The base material is aluminium galvanized color profiled steel sheet which chip with glass fibre of not less than 100mm thick and the bulk density is not less than 60Kg/ m°. The colour profiled steel sheet is more than 0.6mm thick. Yield strength of steel plate is 345MPathe weight of double plated Al-Zn is 180g! m?, fixed with selftapping screw. Fasteners should adapt to the fixed components. 100mm thick light ste! keel drywall gypsum wallboard partition is used for the interior walls, 2mm thick gypsum wallboard shall be meet fireproof and moistureproof properties. ) Flashing and flanging: Flashing, sealants and flanging shall be used on slopes, corners, eaves, doors, windows, framed openings, penetrating tube location, and other locations that need sealing or have Perfect appearance . The materials and colour shall be consistent with the main materials. ‘The location where roof edges joint, ends joint and flashings need sealant to seal. d) Window: Unless specified, all windows are single frame , airtight double glazing aluminium alloy windows with white surface colour. Hinges, supports and handles of their hardwares are made of stainless steel castings. The others like connectors, tapping screws and embedded parts must have the performance of anti-corrosion and anti-rust besides adequate strength.The glazing aluminium alloy windows screens are made of stainless steel. Glass is 6+12+6(mm) transparent glass. The aluminium alloy windows should satisfy the main physical property index listed here below. + Wind load resistance performance: >3. 5kPa + Air permeability <0.5n'/nm + Watertightness: 2600Pa + Heat preservation: <2. O/a".k + Sound insulation: + Transmitting rebate factor: ©) Doors:Aan ope BASIC DESIGN DOC. NO.: GEN -CIV-SPC-0004 REV. B PAGE 9 OF 13 Unless specified, outside doors are anti-fire, anti-theft, anti-coldness, anti-noise, airtight and security steel door or aluminium alloy door. Inside door is wood door or fire door. All doors should have lockset. Hinges, supports and handles are made of stainless steel castings and the others like connectors, tapping screws and embedded parts must have the performance of anti-corrosion and anti-ust besides adequate strength. The aluminium alloy door glass of outside door is 6+12+6(mm) transparent glass. The aluminium alloy doors should satisfy the main physical property index listed here below. + Wind load resistance performance: 23. 5kPa + Air permeability: <0.50°/hom + Watertightness: 2600Pa + Heat preservation: <2. OW, + Sound insulation: 24008 + Transmitting rebate factor: 0.45 1 Canopy: External canopies can be installed as required at all personnel doors, pipelines coming inside through the roof edge and the pipeline opening. Canopies should be supported by a Tigid framework. 3.2 Building design - reinforced concrete frame a) Roofing: Reinforced concrete flat with color steel panel roof: double overhead slope. The bottom is reinforced concrete roof slab, and the top is minimum 100mm thick light steel roof capped with corrugated composite plate. Sandwich plate is used for the roof. The base material is aluminium galvanized color profiled steel sheet which chip with fibreglass of not less than 100mm in thickness and the bulk density is not less than 60Kg/mm’, The color profiled steel sheet is more than 0.6mm thick. Yield strength of steel plate is 345MPa.the weight of double plated Al-Zn is 180g/m?, fixed with self-tapping screw. Fasteners should adapt to the fixed components. b) Wall: 400mm-thick concrete solid blocks are used for the exterior walls. 200mm-thick concrete solid blocks are used for the interior walls. c) Window: Outside windows are aluminium alloy windows and steel! blast-resistant windows. Inside windows are anti-fire windows. Hinges, supports and handles are made of stainless steel castings and the others like connectors, tapping screws and embedded parts must have the performance of anti-corrosion and anti-tust besides adequate strength. Glazing aluminium alloy windows screens are made of stainless steel. Glass is 6+12+6(mm) transparent glass.Aan= a wr- BASIC DESIGN DOC. NO.: GEN -CIV-SPC-0004 REV. B PAGE 10 OF 13 The aluminium alloy windows should satisfy the main physical property index listed here below. + Wind load resistance performance: >3. 5kPa + Air permeability: <0.5 a'/hm + Watertightness: >600Pa + Heat preservation: <2, O1/a".k + Sound insulation: 240 db + Transmitting rebate factor: >0.45 4) Doors: Outside doors are aluminium-alloy or steel anti-fre or blast-resistant doors. Inside doors are sliding aluminium-alloy door, glass is 6mm tempered glass. Hinges, supports and handles are made of stainless steel castings and the others like connectors, tapping ‘screws and embedded parts must have the performance of anti-corrosion and anti-rust besides adequate strength. The aluminium alloy door glass of outside door is 6+12+6(mm) transparent glass. The aluminium alloy doors should satisfy the main physical property index listed here below. + Wind load resistance performance: 23. 5kPa + Air permeability: <0.50'/h.m + Watertightness: 2000Pa + Heat preservation: <2. 00/a'.k + Sound insulation: 24) dB + Transmitting rebate factor: > 045 3.3 Suspended Ceilings All materials utilised for suspended ceilings and finishes shall be noncombustible types.The use of the systems described below shall take into consideration requirements relating to lighting, ventilation, fire prevention and service,maintenance or other functional requirements. Ceilings shall be fire rated and/or shall utilise full height cavity barriers within roof voids to ensure fire separation of rooms where required by local regulation or to EMPLOYER requirements. 3.4 Surface Finishes Where finishes are specified, except to the extent specified herein, these shall be to the approval of EMPLOYER, for example, in the selection of paint or tile colours and floor surfacing materials.Aan ope BASIC DESIGN DOC. NO.: GEN -CIV-SPC-0004 REV. B PAGE 11 OF 13 3.5 Stairs, Ramps and Balustrading All external concrete stairs, ramps, platforms and balustrading shall be designed and built in accordance with the requirements specified in relevant codes and standards. Concrete stairs shall incorporate non-slip, hard wearing stair nosings installed at all stair treads. Ramps for disabled use will not be required. Handrails and balustrades shall be galvanised steel tubular sections, painted in accordance with required standards. Balustrading shall incorporate demountable sections in locations where equipment access is required. Handrails shall be designed such that where required for equipment installation there are appropriate demountable sections, designed and specified to ensure compliance with Uniform Building Code (UBC) safety requirements. 4.0 ENGINEERING PRACTICE LIST The engineering practice includes floor, wall, ceiling,roof, ramp, step.skirting, apron etc. Engineering practice list Floor 1: Conerete tloor Hloor 2: Beige ceramic tiles(6U0x6UUmm ) 140mm thick €20 fine aggregate concrete placing and toweling, dregged 1:1 cement sard over the floor finish the floor. 2.Cement slurry(mixes the construction adhesive) 3. 60mm thick C15 concrete cushion 4. Soil compaction. Compaction coefficient 0.95 110mm thick tiles, dry cement wiping seam. 2. 6mm cement mortar with construction adhesive. 3. Painted again grout (mixed construction adhesive). 4. 60mm thick C15 concrete cushion 5. Soil compaction.Compaction coefficient 0.95 Floor 3: White Anti-skid ceramic tiles (300x450mm) Floor 4; Anti-static (600x600mm) 1. 8mm thick tiles, dry cement wiping seam. 2. 6mm cement mortar with construction adhesive. 3. 1.5 mm thick polyurethane waterproof layer. 4. 20mm thick 1:3 cement mortar to find the slope layer. 5. Painted again grout (mixed construction adhesive). 6. 60mm thick C15 concrete cushion 7. Soil compaction. Compaction coefficient 0.95, 1.600 high elevated active wooden floor 2.20 thick 1:3 cement mortar, to be stripped and compaction 3.1.5 mm thick polyurethane waterproof layer. 4, 20mm thick 1:3 cement mortar to find the slope layer. '5.Cement slurry(mixes the construction adhesive) 6.60mm thick C15 conerete cushion 7.Soil tamp,Compaction coefficient 0.95 Floor 5: Anti-acid tiles (600X600mm ) Floor 6: Marble tiles (600X600mm ) 1. 30mm thick acid-resisting ceramic tile using furan mastic tick off seam 2. 5-7 thick KPF1 potassium sodium silicate, 1. 20mm thick marble, dry cement wiping seam. 2.30 thick 1:3 cement mortar, to be strippedAan= a wr- BASIC DESIGN DOC. NO.: GEN -CIV-SPC-0004 REV. B PAGE 12 OF 13 ‘cement in combination with thick layer 3.1.5 mm thick polyurethane waterproof layer. 4. 20mm thick 1:3 cement mortar to find the slope. layer. 5. Painted again grout (mixed construction adhesive). 6. 60mm thick C15 concrete cushion 7. Soil compaction. Compaction coefficient 0.95 ‘and compaction. 3. Painted again grout (mixed construction adhesive). 4. 60mm thick C15 concrete cushion. 5. Soil compaction. Compaction coefficient 0.95 Wall1: Emulsion paint (Interior Wall) Wall2: Ceramic tiles (Interior Wall) 1. latex paint finish painted twice 2. Seal bottom coating painted once 3, 2mm thick waterproof putty leveling 4. 9mm thick 1:0.5:3 cement lime putty mortar leveling 5. Cement slurry scraping(mixes the construction adhesive) 1. The white cement scratches the seam 2. 8mm thick colored glaze ceramic tiles (Tile soaked for at least two hours later and then paste) 3. 4mm thick force rubber powder putty tack coat, rubs pushes the compaction. 4.1.5 mm thick polyurethane waterproof layer. 5. 9mm thick 1:3 cement mortar leveling 6. Cement slurry scraping(mixes the construction adhesive) Wall: Anti-acid tiles Interior Wall) Wall4: Marble tiles (Interior Wall) 1. The white cement scratches the seam 2. 10mm thick anti-acid tiles (Tile soaked for at least two hours later and then paste) 3. 4mm thick force rubber powder putty tack coat, Tubs pushes the compaction 4.1.5 mm thick polyurethane waterproof layer. 5. 9mm thick 1:3 cement mortar leveling 6. Cement slurry scraping(mixes the construction adhesive) 1.Thin cement wiping seam. 2. 812mm thick marble tles.( specia adhesive bond) 3.6mm thick 1:2.5 cement mortar leveling 4, 9mm thick 1:3 cement mortar scraping 5. Cement slurry scraping(mixes the construction adhesive) WallS: Emulsion paint (Exterior Wall) Wall6: Ceramic tiles (Exterior Wall) 1. Acrylic emulsion paint 2 coat 2. 3~mm cement mortar within a layer of Anti- alkaline fabric 3. Cement mortar leveling 4. Wall layer 1. Acrylic emulsion paint 2 coat 2. 3~5mm cement mortar within a layer of Anti- alkaline fabric 3. Cement mortar leveling 4. Wall layer Ceiling 1: Light steel keel Mineral wool slab cceiling(600x600mm) Ceiling 2: Light steel keel gypsum board 1.12 thick slag wool sound-absorbing panel surface, standard( 600x600) 2.T-cladding light weight steel secondary keel 1. latex paint finish painted twice 2.2 thick waterproof putty leveling 3.12 thick gypsum boardAan= a wr- BASIC DESIGN DOC. NO.: GEN -CIV-SPC-0004 REV. B PAGE 13 OF 13 TB24x28 distance 600 spliced with major keel 3.7-cladding light weight steel secondary Keel TB24x38(or TB24x28) ,distance 600,fixed with main keel by pendant. 4.U-cladding light weight steel main keelCB38x12,distance<1200 jointed with the steel boom by hanger then leveling. 5.06 steel boom two-way midordinate<1200,the top of boom is fixed with future expanding stee! hanger. 4-T-cladding light weight steel secondary keel TB24x28, distance 600,spliced with major keel. 5.T-cladding light weight steel secondary keel ‘TB24x38(or TB24x28) ,distance 600,fixed with main keel by pendant. 6.U-cladding light weight steel main keelCB38x12,distance<1200 jointed with the steel boom by hanger then leveling. 7.06 steel boom two-way midordinate< 1200,the top of boom is fixed with future expanding steel hanger. Ceiling 3: Aluminum alloy square plate (300x300mm) Celling 4: Emulsion paint 1. Aluminum alloy square plate 300 X300 fixed with special supporting keel. 2. A square plate connected with special lower keel ,the distance <600mm. 3.Special upper keel (<1200mm) make leveling. 4.10 galvanized low carbon steel wire boom, the boom fixed with reserve rings. 5.110 steel ring should be Cast-in-place reinforced concrete board reserved reinforced exchange, distance < 1200mm 1. latex paint finish painted once. 2. Multi-color synthetic resin emulsion inner wall coating painted once. 3.2 thick waterproof putty leveling 4, 3.5 thick anti-cracking putty leveling 5, 5mm thick 1:0.5:3 lime mortar cement paste 6. 3mm thick 1:0.5:1 lime mortar cement paste 7. Cement slurry scraping(mixes the construction adhesive) Roof 1 Ramp: Cement surface ramp 1. 20mm 1:3 cement mortar surface layer 2. 10mm weak cement mortar isolated layer 3. 1.5+1.5mm waterproof EPDM membrane 4. 20mm 1:3 cement mortar screeding layer 5, 60mm extruded polystyrene foam board 6. 30mm thick LC5.0 light weight aggregate concrete slope layer (2%) 7. reinforced concrete roof stab 1.20 thick 1:2 cement mortar sweep surface 2.One coat of plain conerete(addition of building adhesive) 3.60 thick C15 concrete,stepped surface slope outward 1%,steel mesh T10,200X200mm 4.100 thick graded sand and gravel 5 Soil tamp,compaction coefficient 0.95 Step 1: Ceramic tiles ‘Step 2: Granite surface entrance step 1.10mm thick tiles, dry cement wiping seam. 2.20 thick 1:3 cement mortar with construction adhesive. 3.Painted again grout (mixed construction adhesive). 4.60 thick C15 concrete, stepped surface slope outward 1% 5 Soil tamp,Compaction coefficient 0.95 1.20 thick pavement of granites 2,plain conerete surface(appropriate sprinkling of water) 3.20 thick 1:3 hard cement mortar coating 4.One coat of plain concrete(addition of building adhesive) 5.60mm thick C15 concrete cushion, stepped surface slope outward 1%Aan ope BASIC DESIGN DOC. NO.: GEN -CIV-SPC-0004 REV. B PAGE 14 OF 13 6 Soil tamp,compaction coefficient 0.95 Skirting1: Ceramic tiles, high=120mm Skirting2: PVC, high=120mm 1. 8-10mm thick floor tiles skirting, cement slury wiping seam. 2. 10mm thick 1:2 cement mortar bonding layer 3. coated with cement mortar once, and made it Tough (mixed with construction glue) 1. The PVC skirting board is installed on metal fastener. 2. The metal fastener should be fixed on the wall with 500mm distance. ‘Apron: Concrete surface apron 1.60 thick C20 concrete surface sprinkle 1:1 cement sand float finish,steel mesh T10,200x200mm 2.100 thick graded sand and gravele 3.Soil tamp slope outward 3%-5%