3X10X5.

5 BOX CELL

DESIGN OF 3 CELL MNB

3 X 10 X 5.5 m
1.0 DESIGN DATA
1.1 GENERAL INFORMATION
This design is for Box Bridge

1.2 DIMENSION DETAILS

No of cells = 3.00 No.s
Skew Angle = 0.00 deg.
Effective Span = 10.50 m
Effective Span (Skew) = 10.50 m
Clear Span = 10.00 m
Clear Span ( Skew) = 10.00 m
Clear Height (at outer edge) = 5.50 m
Clear Height (at median location) = 5.50 m
Width of road at top = 12.50 m
Width of Box = 12.50 m
Width of Box ( skew) = 12.500 m
Wearing coat thickness = 0.056 m
Ht of fill (W.C / P.C.C / pavement layers) over the top slab = 0.000 m
Thickness of top slab = 0.500 m
Thickness of bottom slab = 0.500 m
Thickness of external vertical wall (SK) = 0.500 m
Thickness of internal vertical wall (SK) = 0.40 m
Size of haunch = 0.90 m
x 0.30 m
Width of Parapet Wall/ Crash Barrier = 0.50 m
Width of Footpath = 0.00 m
Distance of edge of parapet wall/Crash Barrier from edge of box = 0.00 m
Height of surcharge = 1.20 m
Safe Bearing Capacity of the soil = 100.00 KN/m2
Permissible Settlement = 10 mm = 75 mm
1333.3
1.3 MATERIAL PROPERTIES
Density of concrete = 25.00 KN/m3
Density of soil = 20.00 KN/m3
Density of Submerged soil = 18.00 KN/m3
Density of wearing coat = 22.00 KN/m3
Angle of internal friction (in degree) = 30.00 deg
Coefficient of earth pressure at rest = 0.500
Coefficient of active earth pressure = 0.279

1.4 DESIGN PARAMETERS

Grade of Concrete = M 35
Grade of Reinforcement = Fe 500
Clear Cover for earth face structural component = 0.075 m
Clear Cover for inside face/ top slab structural component = 0.040 m
Clear Cover for bottom slab = 0.075 m
 3X10X5.5 BOX CELL

2.0 LOAD CALCULATIONS FOR THE BOX STRUCTURE

2.1 DEAD LOAD

Self weight of the structure has been calculated directly in STAAD file by the comment "SELFWEIGHT -1".

2.2 SUPER IMPOSED DEAD LOAD

Wearing coat thickness = 0.056 m
2
Intensity of Loading due to surfacing = 1.232 kN/m
Load (UDL) on top slab = = 1.23 kN/m
Wt of Parapet Wall/Crash Barrier per meter = 10.00 kN/m
Total UDL load due to S.I Dead Load = 11.23 kN/m

2.3 EARTH PRESSURE

Thickness of top slab = 0.500 m
Height of top haunch = 0.300 m
Clear height between top & bottom slab = 5.50 m
Height of bottom haunch = 0.900 m
Thickness of bottom slab = 0.500 m
 3X10X5.5 BOX CELL

Earth Pressure at Rest

Height from top Intensity of Earth pressure
(m) (KN/m2)
0.306 0.306 0.5 x 20 x 0.306 = 3.060
0.250 0.556 0.5 x 20 x 0.556 = 5.560
0.300 0.856 0.5 x 20 x 0.856 = 8.560
1.225 2.081 0.5 x 20 x 2.081 = 20.810
1.225 3.306 0.5 x 20 x 3.306 = 33.060
1.225 4.531 0.5 x 20 x 4.531 = 45.310
1.225 5.756 0.5 x 20 x 5.756 = 57.560
0.300 6.056 0.5 x 20 x 6.056 = 60.560
0.250 6.306 0.5 x 20 x 6.306 = 63.060

Active Earth Pressure

Height from top Intensity of Earth pressure
(m) (KN/m2)
0.306 0.306 0.2794 x 20 x 0.306 = 1.710
0.250 0.556 0.2794 x 20 x 0.556 = 3.107
0.300 0.856 0.2794 x 20 x 0.856 = 4.784
1.225 2.081 0.2794 x 20 x 2.081 = 11.629
1.225 3.306 0.2794 x 20 x 3.306 = 18.474
1.225 4.531 0.2794 x 20 x 4.531 = 25.320
1.225 5.756 0.2794 x 20 x 5.756 = 32.165
0.300 6.056 0.2794 x 20 x 6.056 = 33.841
0.250 6.306 0.2794 x 20 x 6.306 = 35.238

Submerged Earth Pressure at Rest

Height from top Intensity of Earth pressure
(m) (KN/m2)
0.306 0.306 0.5 x 18 x 0.306 = 2.754
0.250 0.556 0.5 x 18 x 0.556 = 5.004
0.300 0.856 0.5 x 18 x 0.856 = 7.704
1.225 2.081 0.5 x 18 x 2.081 = 18.729
1.225 3.306 0.5 x 18 x 3.306 = 29.754
1.225 4.531 0.5 x 18 x 4.531 = 40.779
1.225 5.756 0.5 x 18 x 5.756 = 51.804
0.300 6.056 0.5 x 18 x 6.056 = 54.504

0.250 6.306 0.5 x 18 x 6.306 = 56.754

 3X10X5.5 BOX CELL

Submerged Active Earth Pressure

Height from top Intensity of Earth pressure
(m) (KN/m2)
0.306 0.306 0.2794 x 18 x 0.306 = 1.54
0.250 0.556 0.2794 x 18 x 0.556 = 2.80
0.300 0.856 0.2794 x 18 x 0.856 = 4.30
1.225 2.081 0.2794 x 18 x 2.081 = 10.47
1.225 3.306 0.2794 x 18 x 3.306 = 16.63
1.225 4.531 0.2794 x 18 x 4.531 = 22.79
1.225 5.756 0.2794 x 18 x 5.756 = 28.95
0.300 6.056 0.2794 x 18 x 6.056 = 30.46
0.250 6.306 0.2794 x 18 x 6.306 = 31.71

2.4 LIVE LOAD SURCHARGE

Equivalent height = 1.20 m
2
Uniform Intensity of loading (Considering coefficient of active earth pressure)= 0.2794 x 1.2 x 20 = 6.71 kN/m
2
Uniform Intensity of loading (Considering coefficient of earth pressure at rest)= 0.5 x 1.2 x 20 = 12.00 kN/m

2.5.1 BRAKING LOAD (Cl. 211.2, IRC: 6-2017)

Load for one lane 70R T 0.2 * 700 = 140 KN

Load for one lane Class A 0.1 * 364 + 0.05 * 364 = 54.6 KN
Carriageway Live Load = 194.6 kN
Width of the box = 12.50 m
Braking Load = 1 x 194.6 / 12.50 = 15.57 kN

BRAKING + CENTRIFUGAL FORCE = 15.57 kN

2.6 CALCULATING BRIDGE TEMPERATURE :

Maximum air shade temperature = 47.5 oC
Minimum air shade temperature = 0 oC
Bridge Temperature = 33.75 oC
 3X10X5.5 BOX CELL

CHECK FOR TEMPERATURE EFFECT; As per IRC - 6:-

Effect of temperature gradient

F = Ec a t A

2
Ec = Modulus of Elasticity of concrete = 3.20E+06 t/m

a = Co-efficient of thermal expansion = 1.20E-05 t/m2

t = Temperature differential

A = Sectional area of section where temperature differential is t

Average thickness of deck slab = 0.5 m

Effect of temperature Rise :-

4 13.8

0.15 1 2

0.15 3

0.15
4
2.1

Sr No. t Factor b d A=bxd Force Acting at Ecc.

1 4.00 1.0 1.0 0.15 0.150 23.04 0.075 -0.075
2 13.80 0.5 1.0 0.15 0.075 39.74 0.050 -0.050
3 4.00 0.5 1.0 0.15 0.075 11.52 0.200 -0.200
4 2.10 0.5 1.0 0.15 0.075 6.05 0.050 0.050
Sum=F 80.352 Sum=F*e -5.72

e* = Eccentricity of force from the centroidal axis of force

M = F*e = Ecat/2Ae

Effect of Temperature Fall :-

9.9 0.7
2 1 0.100

3 0.125

6 0.125

4 5 0.100
5.8 0.8
 3X10X5.5 BOX CELL

Sr No. t Factor b d A=bxd Force Acting at Ecc.

1 0.70 1.0 1.0 0.100 0.100 2.69 0.050 -0.050

2 9.90 0.5 1.0 0.100 0.050 19.01 0.033 -0.033

4 5.80 0.5 1.0 0.100 0.050 11.14 0.033 0.033
5 0.80 1.0 1.0 0.100 0.100 3.07 0.050 0.050
6 0.80 0.5 1.0 0.125 0.063 1.92 0.142 0.142
Sum=F 39.504 Sum=F*e -0.209

Effect of Uniform Temperature:-

(As per Clause - 218.2,IRC-6)

Maximum temperature of the region = 47.5 degree

Minimum temperature of the region = 2.50 degree

Difference between Maximum & Minimum Air temperature = 45.0 degree

So,the bridge temperature at the time of constraint Max = 32.5 degree

So,the bridge temperature at the time of constraint Min = 12.5 degree

Variation in temperature fall/rise to be taken = 32.5 degree

say (+/-) 35.0 degree

While applying it to STAAD file, as E values are to be taken half for long time effect, temp. is reduced to half
while keeping E value as full. i.e 17.5 degree.
 3X10X5.5 BOX CELL

Creep Coefficent

fck = 35 Mpa
fcm = 45 Mpa
t = 25550 days
to = 90 days
Φ (t, to) = Φo βc ( t , to )
Φo = ΦRH β(fcm) β(to)

ΦRH = Factor to allow for the effect of relative humidity on the notional creep coefficient
= 1+ 1 - RH/100 for fcm ≤ 45 Mpa
0.1 ( ho )1/3
=
1+ 1 - RH/100 for fcm > 45 Mpa
α1 * α2
1/3
0.1 ( ho )

RH = Relative humidity of the ambient environment in percent = 80 %

α = coefficient to consider the influence of the concrete strength
α1 = [ 43.75 / fcm ]0.7 α2 = [ 43.75 / fcm ]0.2 α3 = [ 43.75 / fcm ]0.5

β(fcm) = factor to allow for the effect of concrete strength on the notional creep coefficient = 18.78 / √fcm
β(to) = factor to allow for the effect of concrete age at loading on the notional
creep coefficient = 1/ ( 0.1+ to 0.2)
Φo = ΦRH x β(fcm) x β(to)
βc( t , to) = coefficient to describe the development of creep with time after loading
= [ (t - to) / (βH + t - to) ]0.3
βH = coefficient depending on the relative humidity(RH in percent) and the notional member size(ho in mm)
Min 1.5 [ 1+ (0.012 RH)18 ] ho +250 for fcm ≤ 45 Mpa
1500
=
Min 1.5 [ 1+ (0.012 RH)18 ] ho +250 α3
for fcm > 45 Mpa
1500* α3

Summary of Creep Coefficent

Element ho (mm) α1 α2 β(fcm) ΦRH β(to) Φo α3 βH βc( t , to) Φ (t, to)
Top Slab 476.19 0.980 0.994 2.800 1.256 0.391 1.374 0.986 1307 0.985 1.353
Side Wall 458.33 0.980 0.994 2.800 1.259 0.391 1.378 0.986 1267 0.986 1.358
Bottom Slab 476.19 0.980 0.994 2.800 1.256 0.391 1.374 0.986 1307 0.985 1.353
FINAL BENDING MOMENT AND SHEAR FORCE
Summary of Bending Moment and Shear Force from STAAD File
Distance from edge of side Bending Moment (kN/m) Shear Force (kN)
Member Case Section wall (m)
ULS SLS (Rare) SLS (QP) ULS

Mid Span 5.250 264.940 182.462 64.142 7.617

Curtailment 3.250 218.685 150.723 54.760 42.833
Sagging
Face of Haunch 1.150 45.556 32.806 7.306 78.245
Top Slab

Face of Support 0.250 67.082 47.619 8.694 94.230

Face of Support 0.250 334.949 228.242 107.270 94.230
Face of Haunch 1.150 182.867 122.760 55.753 78.245
Hogging
Curtailment 3.250 42.483 38.670 31.045 42.833
Mid Span 5.250 72.843 53.705 15.430 7.617

Mid Span 3.000 119.1 97.799 80.149 7.752

Curtailment 1.775 84.1 73.538 65.263 66.948
Sagging
Face of Haunch 0.550 21.8 19.817 15.929 181.856
Side Wall

Face of Support 0.250 23.3 21.475 17.900 213.991

Face of Support 0.250 195.8 132.903 79.163 213.991
Face of Haunch 0.550 140.1 95.974 47.770 181.856
Hogging
Curtailment 1.775 125.8 87.255 37.751 66.948
Mid Span 3.000 159.4 110.509 46.646 7.752

Mid Span 5.250 66.755 46.574 24.236 5.953

Curtailment 3.250 102.753 71.505 33.097 50.928
Sagging
Face of Haunch 1.150 96.141 66.657 29.786 92.350
Bottom Slab

Face of Support 0.250 36.523 31.055 20.117 105.457

Face of Support 0.250 196.832 131.987 91.562 105.457
Face of Haunch 1.150 112.356 80.660 64.322 92.350
Hogging
Curtailment 3.250 22.963 20.820 16.532 50.928
Mid Span 5.250 2.600 1.950 0.650 5.953

Mid Span 3.000 55.539 38.308 3.845 9.966

Curtailment 1.775 94.082 72.494 29.319 9.966
Intermediate Wall

Sagging
Face of Haunch 0.550 72.100 56.162 24.287 9.966
Face of Support 0.250 84.088 65.070 27.032 9.966
Face of Support 0.250 159.438 105.784 29.736 9.966
Face of Haunch 0.550 136.764 90.767 26.536 9.966
Hogging
Curtailment 1.775 44.570 29.708 13.467 9.966
Mid Span 3.000 34.588 23.458 4.395 9.966
Temperature leading
Summary of Bending Moment and Shear Force from STAAD File
Distance from edge of side
Member Case Section wall (m) Bending Moment

ULS SLS (Rare) ULS

Sagging Mid Span 5.250 88.171 64.617 7.617
Curtailment 3.250 76.245 55.763 42.833
Face of Haunch 1.400 7.306 7.306 78.245
Top Slab

Face of Support 0.500 8.694 8.694 94.230

Hogging Face of Support 0.500 195.071 134.990 94.230
Face of Haunch 1.400 117.457 79.153 78.245
Curtailment 3.250 31.045 31.045 42.833
Mid Span 5.250 15.430 15.430 7.617

Sagging Mid Span 3.500 92.686 80.149 7.752

Curtailment 2.150 72.759 65.263 66.948
Side Wall

Face of Haunch 0.800 15.929 15.929 181.856

Face of Support 0.500 17.900 17.900 213.991
Hogging Face of Support 0.500 141.481 96.703 213.991
Face of Haunch 0.800 82.132 57.339 181.856
Curtailment 2.150 52.853 38.644 66.948
Mid Span 3.500 64.558 47.273 7.752

Sagging Mid Span 5.250 35.763 25.912 5.953

Curtailment 3.250 46.844 34.232 50.928
Bottom Slab

Face of Haunch 1.400 43.708 31.702 92.350

Face of Support 0.500 20.117 20.117 105.457
Hogging Face of Support 0.500 172.409 115.705 105.457
Face of Haunch 1.400 90.148 64.322 92.350
Curtailment 3.250 16.532 16.532 50.928
Mid Span 5.250 0.650 0.650 5.953

Sagging Mid Span 3.500 3.845 3.845 9.966

Curtailment 2.150 29.319 29.319 9.966
Intermediate Wall

Face of Haunch 0.800 24.287 24.287 9.966

Face of Support 0.500 27.032 27.032 9.966
Hogging Face of Support 0.500 61.882 40.746 9.966
Face of Haunch 0.800 55.242 36.419 9.966
Temperature accompanying
Summary of Bending Moment and Shear Force from STAAD File
Distance from centreline of side
Member Case Section wall (m) Bending Moment

ULS SLS (Rare) SLS (QP) ULS

Sagging Mid Span 5.250 87.602 64.237 64.142 7.617
Curtailment 3.250 75.041 54.960 54.760 42.492
Face of Haunch 1.400 7.306 7.306 7.306 77.904
Top Slab

Face of Support 0.500 8.694 8.694 8.694 93.889

Hogging Face of Support 0.500 192.861 133.517 107.270 93.889
Face of Haunch 1.400 115.554 77.885 55.753 77.904
Curtailment 3.250 31.045 31.045 31.045 42.492
Mid Span 5.250 15.430 15.430 15.430 7.617

Sagging Mid Span 3.500 92.590 80.149 80.149 7.752

Curtailment 2.150 71.688 65.263 65.263 66.151
Face of Haunch 0.800 15.929 15.929 15.929 181.059
Side Wall

Face of Support 0.500 17.900 17.900 17.900 213.194

Hogging Face of Support 0.500 139.194 95.178 79.163 213.194
Face of Haunch 0.800 80.084 55.974 47.770 181.059
Curtailment 2.150 51.781 37.930 37.751 66.151
Mid Span 3.500 63.806 46.771 46.646 7.752

Sagging Mid Span 5.250 35.724 25.886 24.236 5.586

Curtailment 3.250 46.053 33.705 33.097 50.193
Face of Haunch 1.400 41.410 30.169 29.786 92.081
Bottom Slab

Face of Support 0.500 20.117 20.117 20.117 105.242

Hogging Face of Support 0.500 169.869 114.012 91.562 105.242
Face of Haunch 1.400 87.850 64.322 64.322 92.081
Curtailment 3.250 16.532 16.532 16.532 50.193
Mid Span 5.250 0.650 0.650 0.650 5.586

Sagging Mid Span 3.500 3.845 3.845 3.845 9.476

Curtailment 2.150 29.319 29.319 29.319 9.476
Intermediate Wall

Face of Haunch 0.800 24.287 24.287 24.287 9.476

Face of Support 0.500 27.032 27.032 27.032 9.476
Hogging Face of Support 0.500 60.532 39.846 29.736 9.476
Face of Haunch 0.800 54.039 35.617 26.536 9.476
Curtailment 2.150 27.526 18.345 13.467 9.476
Mid Span 3.500 6.013 4.408 4.395 9.476
Only Live load
Summary of Bending Moment and Shear Force from STAAD File
Distance from centreline of side
Member Case Section wall (m) Bending Moment

Acc Acc LL
Leading Leading LL Leading LL Leading Acc Factor ( LL Accompanying
70RT KN 40T KN Impact Factor LL Factor ( Factor ( Accompanying
Factor(ULS) Factor (RARE) (ULS) (Rare) ULS) (ULS)
ULS) rare) (Rare)

Sagging Mid Span 5.250 94.580 -7.169 -1.000 -7.169 71.690 1.250 118.225 1.500 1.000 177.338 118.225 1.150 0.400 0.750 135.959 88.669 0.750 88.669

Curtailment 3.250 76.610 -6.004 -1.000 -6.004 60.040 1.250 95.763 1.500 1.000 143.644 95.763 1.150 0.900 0.750 110.127 71.822 0.750 71.822

Face of Haunch 1.400 20.030 -2.040 -1.000 -2.040 20.400 1.250 25.500 1.500 1.000 38.250 25.500 1.150 1.400 0.750 29.325 19.125 0.750 19.125

Face of Support 0.500 31.140 -2.346 -1.000 -2.346 23.460 1.250 38.925 1.500 1.000 58.388 38.925 1.150 1.500 0.750 44.764 29.194 0.750 29.194
Top Slab

Hogging Face of Support 0.500 75.780 5.225 -1.000 5.225 52.250 1.250 94.725 1.500 1.000 142.088 94.725 1.150 1.500 0.750 108.934 71.044 0.750 71.044

Face of Haunch 1.400 35.900 2.504 -1.000 2.504 25.040 1.250 44.875 1.500 1.000 67.313 44.875 1.150 1.400 0.750 51.606 33.656 0.750 33.656

Curtailment 3.250 5.800 0.406 -1.000 0.406 4.060 1.250 7.625 1.500 1.000 11.438 7.625 1.150 0.900 0.750 8.769 5.719 0.750 5.719

Mid Span 5.250 30.620 2.212 -1.000 2.212 22.120 1.250 38.275 1.500 1.000 57.413 38.275 1.150 0.400 0.750 44.016 28.706 0.750 28.706

Sagging Mid Span 3.500 14.120 -1.025 -1.000 -1.025 10.250 1.250 17.650 1.500 1.000 26.475 17.650 1.150 0.400 0.750 20.298 13.238 0.750 13.238

Curtailment 2.150 6.620 -0.470 -1.000 -0.470 4.700 1.250 8.275 1.500 1.000 12.413 8.275 1.150 0.900 0.750 9.516 6.206 0.750 6.206

Face of Haunch 0.800 3.110 -0.238 -1.000 -0.238 2.380 1.250 3.888 1.500 1.000 5.831 3.888 1.150 1.400 0.750 4.471 2.916 0.750 2.916
Side Wall

Face of Support 0.500 2.860 -0.249 -1.000 -0.249 2.490 1.250 3.575 1.500 1.000 5.363 3.575 1.150 1.500 0.750 4.111 2.681 0.750 2.681

Hogging Face of Support 0.500 30.180 2.626 -1.000 2.626 26.260 1.250 37.725 1.500 1.000 56.588 37.725 1.150 1.500 0.750 43.384 28.294 0.750 28.294

Face of Haunch 0.800 32.000 2.598 -1.000 2.598 25.980 1.250 40.000 1.500 1.000 60.000 40.000 1.150 1.400 0.750 46.000 30.000 0.750 30.000

Curtailment 2.150 39.460 2.607 -1.000 2.607 26.070 1.250 49.325 1.500 1.000 73.988 49.325 1.150 0.900 0.750 56.724 36.994 0.750 36.994

Mid Span 3.500 50.990 3.475 -1.000 3.475 34.750 1.250 63.738 1.500 1.000 95.606 63.738 1.150 0.400 0.750 73.298 47.803 0.750 47.803

Sagging Mid Span 5.250 12.210 0.832 -1.000 0.832 8.320 1.250 20.688 1.500 1.000 31.031 20.688 1.150 0.254 0.750 23.791 15.516 0.750 15.516

Curtailment 3.250 30.000 1.984 -1.000 1.984 19.840 1.250 37.800 1.500 1.000 56.700 37.800 1.150 0.272 0.750 43.470 28.350 0.750 28.350

Face of Haunch 1.400 29.190 1.958 -1.000 1.958 19.580 1.250 36.488 1.500 1.000 54.731 36.488 1.150 0.450 0.750 41.961 27.366 0.750 27.366
Bottom Slab

Face of Support 0.500 8.750 0.626 -1.000 0.626 6.260 1.250 10.938 1.500 1.000 16.406 10.938 1.150 0.700 0.750 12.578 8.203 0.750 8.203

Hogging Face of Support 0.500 13.010 -1.438 -1.000 -1.438 14.380 1.250 17.975 1.500 1.000 26.963 17.975 1.150 0.700 0.750 20.671 13.481 0.750 13.481

Face of Haunch 1.400 13.070 -1.027 -1.000 -1.027 10.270 1.250 16.338 1.500 1.000 24.506 16.338 1.150 0.450 0.750 18.788 12.253 0.750 12.253

Curtailment 3.250 3.070 -0.343 -1.000 -0.343 3.430 1.250 4.288 1.500 1.000 6.431 4.288 1.150 0.272 0.750 4.931 3.216 0.750 3.216

Mid Span 5.250 0.810 -0.075 -1.000 -0.075 0.750 1.250 1.300 1.500 1.000 1.950 1.300 1.150 0.254 0.750 1.495 0.975 0.750 0.975

Sagging Mid Span 3.500 27.570 -2.003 -1.000 -2.003 20.030 1.250 34.463 1.500 1.000 51.694 34.463 1.150 0.339 0.750 39.632 25.847 0.750 25.847

Curtailment 2.150 34.540 -2.297 -1.000 -2.297 22.970 1.250 43.175 1.500 1.000 64.763 43.175 1.150 0.339 0.750 49.651 32.381 0.750 32.381

Face of Haunch 0.800 25.500 -1.700 -1.000 -1.700 17.000 1.250 31.875 1.500 1.000 47.813 31.875 1.150 0.339 0.750 36.656 23.906 0.750 23.906
Intermediate Wall

Face of Support 0.500 30.430 -2.026 -1.000 -2.026 20.260 1.250 38.038 1.500 1.000 57.056 38.038 1.150 0.339 0.750 43.743 28.528 0.750 28.528

Hogging Face of Support 0.500 52.750 3.819 -1.000 3.819 38.190 1.250 65.938 1.500 1.000 98.906 65.938 1.150 0.339 0.750 75.828 49.453 0.750 49.453

Face of Haunch 0.800 44.120 3.190 -1.000 3.190 31.900 1.250 55.150 1.500 1.000 82.725 55.150 1.150 0.339 0.750 63.423 41.363 0.750 41.363

Curtailment 2.150 9.090 0.642 -1.000 0.642 6.420 1.250 11.363 1.500 1.000 17.044 11.363 1.150 0.339 0.750 13.067 8.522 0.750 8.522

Mid Span 3.500 15.240 1.014 -1.000 1.014 10.140 1.250 19.050 1.500 1.000 28.575 19.050 1.150 0.339 0.750 21.908 14.288 0.750 14.288
Temperature Leading+Live Load accompanying
Summary of Bending Moment and Shear Force from STAAD File
Distance from edge of side wall (m)
Member Case Section

ULS SLS Rare

Sagging Mid Span 5.250 224.130 153.286
Curtailment 3.250 186.372 127.585
Face of Haunch 1.400 36.631 26.431
Top Slab

Face of Support 0.500 53.458 37.888

Hogging Face of Support 0.500 304.005 206.034
Face of Haunch 1.400 169.063 112.809
Curtailment 3.250 39.814 36.764
Mid Span 5.250 59.446 44.136

Sagging Mid Span 3.500 112.984 93.387

Curtailment 2.150 82.275 71.469
Face of Haunch 0.800 20.400 18.845
Side Wall

Face of Support 0.500 22.011 20.581

Hogging Face of Support 0.500 184.865 124.997
Face of Haunch 0.800 128.132 87.339
Curtailment 2.150 109.577 75.638
Mid Span 3.500 137.856 95.076

Sagging Mid Span 5.250 59.554 41.428

Curtailment 3.250 90.314 62.582
Face of Haunch 1.400 85.669 59.068
Bottom Slab

Face of Support 0.500 32.695 28.320

Hogging Face of Support 0.500 193.080 129.186
Face of Haunch 1.400 108.936 76.575
Curtailment 3.250 21.463 19.748
Mid Span 5.250 2.145 1.625

Sagging Mid Span 3.500 43.477 29.692

Curtailment 2.150 78.970 61.700
Intermediate Wall

Face of Haunch 0.800 60.943 48.193

Face of Support 0.500 70.775 55.560
Hogging Face of Support 0.500 137.710 90.199
Face of Haunch 0.800 118.665 77.782
Curtailment 2.150 41.197 27.270
Mid Span 3.500 27.997 18.746
Temperature Accompanying+Live Load(Live Load leading)
Summary of Bending Moment and Shear Force from STAAD File
Distance from centreline of side
Member Case Section wall (m) Bemding Moment

ULS SLS Rare

Sagging Mid Span 5.250 264.940 182.462
Curtailment 3.250 218.685 150.723
Face of Haunch 1.400 45.556 32.806
Top Slab

Face of Support 0.500 67.082 47.619

Hogging Face of Support 0.500 334.949 228.242
Face of Haunch 1.400 182.867 122.760
Curtailment 3.250 42.483 38.670
Mid Span 5.250 72.843 53.705

Sagging Mid Span 3.500 119.065 97.799

Curtailment 2.150 84.101 73.538
Face of Haunch 0.800 21.760 19.817
Side Wall

Face of Support 0.500 23.263 21.475

Hogging Face of Support 0.500 195.782 132.903
Face of Haunch 0.800 140.084 95.974
Curtailment 2.150 125.769 87.255
Mid Span 3.500 159.412 110.509

Sagging Mid Span 5.250 66.755 46.574

Curtailment 3.250 102.753 71.505
Face of Haunch 1.400 96.141 66.657
Bottom Slab

Face of Support 0.500 36.523 31.055

Hogging Face of Support 0.500 196.832 131.987
Face of Haunch 1.400 112.356 80.660
Curtailment 3.250 22.963 20.820
Mid Span 5.250 2.600 1.950

Sagging Mid Span 3.500 55.539 38.308

Curtailment 2.150 94.082 72.494
Intermediate Wall

Face of Haunch 0.800 72.100 56.162

Face of Support 0.500 84.088 65.070
Hogging Face of Support 0.500 159.438 105.784
Face of Haunch 0.800 136.764 90.767
Curtailment 2.150 44.570 29.708
Mid Span 3.500 34.588 23.458
 3X10X5.5 BOX CELL

DESIGN OF TOP SLAB

MIDSPAN - SAGGING
Depth of member (D) = 500.00 mm
Width of the member (b) = 1000.00 mm

MATERIAL PROPERTIES :
Grade of concrete, fck = 35 MPa
Mean value of concrete compressive strength, fcm = 45 MPa
Grade of Reinforcement = 500 MPa
fywd 0.8 fyk = 400 MPa
Clear cover of top slab = 40 mm
Modulus of Elasticity steel Es = 200000 MPa
For short Term loading Ecm = 32308 MPa
For long Term loading Ecm' = 13728 MPa
fctm = 2.80 MPa
fcteff = Max of 2.9 Mpa or fctm = 2.90 MPa
fcd = 15.75 MPa
Cross sectional Area, Ac = 5.000 m2
Perimeter in contact with atmosphere u = 21.00 m
Notational size ho = 476.19 mm
Age of concrete at the time of loading = 90 days
t∞ considered = 25550 days
Creep factor Φ= 1.3534
εuk = 0.00450
εud = 0.00405
εcu2 = 0.0035
xumax/d = 0.4636

PERMISSIBLE STRESSES
1) Permissble concrete compressive stresses
Load Combination Permissble Stress
SLS Rare 0.48 fck = 16.8 MPa
SLS QP 0.36 fck = 12.6 MPa

2) Permissble Tensile stress in steel (Rare) 0.6 fy = 300 MPa

0.8 fy = 400 MPa
3) Permissible crack width wk
SLS QP Load combination = 0.3 mm

Maximum Reinforcement
[ Tension Reinf. ] ≤ 0.025AC At section other than Laps
[ Tension + Compression ] ≤ 0.04AC At any section
Where AC = Gross Cross section Area of Concrete

Minimum Reinforcement :
Ast min = Max [ 0.26 fctm / fyk bt d , 0.0013 bt d ] (Refer IRC:112 clause 16.5.1.1)
bt = Mean width of Tension zone.
 3X10X5.5 BOX CELL

A) ULS CAPACITY CHECK (Top Slab Sagging)

Section Mid Span Curtailment point Face of Haunch Face of Support

Distance from centreline of side wall m 5.250 3.250 1.150 0.250

MED (Sagging) kNm 264.940 218.685 45.556 67.082
Width (b) mm 1000.000 1000.000 1000.000 1000.000
Overall depth D mm 500.000 500.000 500.000 500.000
d mm 452.000 452.000 452.000 452.000
Diameter mm 16 12 16 12 16 0 16 0
Area of steel
Spacing mm 200 200 200 200 200 200 200 200
provided
Ast, Provided mm2 1570.796 1570.796 1005.310 1005.310
Reinforcement (%)
xmax mm 209.536 209.536 209.536 209.536
xu = 0.87 fyk Ast / 0.362 fck b mm 53.930 53.930 34.515 34.515
Check UR, OK UR, OK UR, OK UR, OK
Ast,cal =M/ 0.87 fyk (d'-0.416 xu) mm2 1417.844 1170.308 239.297 352.367
Ast Max mm2 200000.000 200000.000 200000.000 200000.000
Check Ast Calc. < Ast Provided < Ast Max OK OK OK OK
Ast min mm2 678.000 678.000 678.000 678.000
∆Fd kN 3.809 21.417 39.123 47.115
z = d- 0.416 xu m 429.565 429.565 437.642 437.642
MED/z +∆Fd kN 620.571 530.501 143.217 200.395
MRd =0.87 fyk Ast (d-0.416 xu) kNm 293.520 293.520 191.385 191.385
MRD/z kNm/m 683.296 683.296 437.310 437.310
Check MRD/z > MED/z + ∆Fd OK OK OK OK

Distribution steel at bottom of top slab: (Refer IRC:112 clause 16.6.1.1)

Distribution Reinforcement : At Least 20% of the main Reinforcement = 314.16 mm2
Provide 12 @ 125 mm c/c = 904.78 mm2 OK
 3X10X5.5 BOX CELL

B) SLS STRESS CHECK

Rare Load combination. Quasi Permanent Load Combination
Ec,eq = Ecm*(MQP+MST) m = Es / Ecm'
MST + (1+ Φ)* MQP
MST = MRARE -MQP
m = Es / Ec,eq
Flexural tensile Strength:
where,

fctm,fl = mean Flexural tensile strength of solid beam

h = total depth of member in mm
Formula used for calculation of stress
dc (depth of neutral axis) = .-m x As + √ ( m2 x AS2 + 2 x m x As x b x d )
b
INA (Transformed) = bx dc3/3 + m x As x (d - dc)2

Compressive stress in concrete σc = MRARE x dc / INA

Tensile stress in steel σs = m x MRARE x (d - dc ) / INA

Stress Check for SLS Load Combinations

SLS (Rare Combination)
Curtailment
Section Mid Span Face of Support Face of Supportr
point
Distance from centreline of side wall m 5.250 3.250 1.150 0.250
MED (Sagging) kNm 182.462 150.723 32.806 47.619
Width (b) mm 1000.000 1000.000 1000.000 1000.000
d mm 452.000 452.000 452.000 452.000
Ast, Provided mm2 1570.796 1570.796 1005.310 1005.310
Checking Section: Cracked or Uncracked
I mm4 7.695E+09 7.695E+09 7.695E+09 7.695E+09
Y = d/2 mm 250.000 250.000 250.000 250.000
σ (Stress) Mpa 5.928 4.896 1.066 1.547
fctm,fl Mpa 3.080 3.080 3.080 3.080
Cracked/Uncracked Cracked Cracked Uncracked Uncracked
Finding Stresses considering Cracked Section
Modular ratio 9.136 9.234 8.056 7.720
N.A. depth (dc) mm 100.448 100.921 77.849 76.359
INA mm4 2.111E+09 2.130E+09 1.291E+09 1.244E+09
Compressive stress Mpa 8.681 7.140 1.978 2.924
Max Compressive Stress Mpa 16.800 16.800 16.800 16.800
Check OK OK OK OK
Tensile stress Mpa 277.549 229.355 76.594 111.049
Maximum Tensile Stress Mpa 400.000 400.000 400.000 400.000
Check OK OK OK OK
 3X10X5.5 BOX CELL

SLS (Quasi Permanent Combination)

Curtailment
Section Mid Span Face of Haunch Face of Support
point
Distance from centreline of side wall m 5.250 3.250 1.150 0.250
MED (Sagging) kNm 64.142 54.760 7.306 8.694
Width (b) mm 1000.000 1000.000 1000.000 1000.000
d mm 452.000 452.000 452.000 452.000
Ast, Provided mm2 1570.796 1570.796 1005.310 1005.310
Checking Section: Cracked or Uncracked
I mm4 7.695E+09 7.695E+09 7.695E+09 7.695E+09
Y = d/2 mm 250.000 250.000 250.000 250.000
σ (Stress) Mpa 2.084 1.779 0.237 0.282
fctm,fl Mpa 3.080 3.080 3.080 3.080
Cracked/Uncracked Uncracked Uncracked Uncracked Uncracked
Finding Stresses considering Cracked Section
Modular ratio 14.569 14.569 14.569 14.569
N.A. depth (dc) mm 122.756 122.756 101.348 101.348
INA mm4 3.097E+09 3.097E+09 2.148E+09 2.148E+09
Compressive stress Mpa 2.542 2.170 0.345 0.410
Max Compressive Stress Mpa 12.600 12.600 12.600 12.600
Check OK OK OK OK
Tensile stress Mpa 99.333 84.804 17.377 20.678
Maximum Tensile Stress Mpa 400.000 400.000 400.000 400.000
Check OK OK OK OK

C) SLS CRACK WIDTH CHECK (QUASI PERMANENT LOAD COMBINATION)

1) CHECK Ast,min for crack control
Curtailment
Section Mid Span Face of Haunch Face of Support
point
Distance from centreline of side wall m 5.250 3.250 1.150 0.250

b mm 1000.000 1000.000 1000.000 1000.000

h mm 500.000 500.000 500.000 500.000
d mm 452.000 452.000 452.000 452.000
Act =bh/2 mm2 250000 250000 250000 250000
σs = fyk Mpa 500.000 500.000 500.000 500.000
k 1.000 1.000 1.000 1.000
kc 0.400 0.400 0.400 0.400
As,min =kc k fct,eff Act /σs 2
mm 580 580 580 580
As,provided mm2 1570.80 1570.80 1005.31 1005.31
Check OK OK OK OK

h 0.00 0.30 0.80 3.00

k 1.00 1.00 0.65 0.65
 3X10X5.5 BOX CELL

2) CHECK FOR MAXIMUM SPACING b/w bars.

Curtailment
Section Mid Span Face of Haunch Face of Support
point
Distance from centreline of side wall m 5.250 3.250 1.150 0.250
Bar diameter mm 16 16 16 16
Cover mm 40 40 40 40
Provided mm 100 100 100 100
Spacing b/w
bars Calculated mm 240 240 240 240
Check OK OK OK OK

3) CHECK FOR CRACK WIDTH ( IRC 112 / clause 10.3.2 (2) )

Curtailment
Section Mid Span Face of Haunch Face of Support
point
Distance from centreline of side wall m 5.250 3.250 1.150 0.250
hc,eff = Min [2.5 (h - d), (h - x)/3 ,
mm 96.82 96.82 96.82 96.82
h/2]
Aceff = hc,eff x b mm2 96821.19 96821.19 96821.19 96821.19
As provided mm2 1570.80 1570.80 1005.31 1005.31
ρpeff = As/Ac,eff 0.0162 0.0162 0.0104 0.0104
Srmax =3.4c + 0.17 Φ /ρPeff mm 303.66 303.66 397.96 397.96
σsc Mpa 99.33 84.80 17.38 20.68
x = neutral axis depth mm 122.76 122.76 101.35 101.35
kt 0.500 0.500 0.500 0.500
αe = Es/Ecm' 14.57 14.57 14.57 14.57
esm - ecm =Max [ [ σsc - kt fct,eff ( 1+ αe ρP,eff ) /
0.00030 0.00025 0.00005 0.00006
ρP,eff ] /Es , 0.6 σsc/Es ]
wk mm 0.0905 0.0773 0.0207 0.0247
Check OK OK OK OK

D) CHECK FOR SHEAR : ( IRC 112 / clause 10.3.2 (2) )

Check of Shear Reinforcement Requirement
Load combination ULS
Curtailment
Section Mid Span Face of Haunch Face of Support
point
VED kN 7.62 42.83 78.25 94.23
β 1.0000 1.0000 1.0000 0.5000
βVED kN 7.62 42.83 78.25 47.12
d mm 452.00 452.00 452.00 452.00
bw mm 1000.00 1000.00 1000.00 1000.00
k= Min [ 1 + √200/d , 2 ] 1.665 1.665 1.665 1.665
Asl 2 1570.796 1570.796 1005.310 1005.310
mm
ρ1 = Min [ Asl/bw d , 0.02 ] 0.003 0.003 0.002 0.002
νmin = 0.031 k3/2 fck1/2 0.394 0.394 0.394 0.394
σcp Mpa 0 0 0 0
VRdc =Max [ ( 0.12 k (80 ρ1 fck
)0.33 + 0.15 σcp ) bw d , (νmin kN 191.368 191.368 178.127 179.443
+0.15σcp ) bw d ]
No Shear reinf. No Shear reinf. No Shear reinf. No Shear reinf.
Check
Required Required Required Required
 3X10X5.5 BOX CELL

DESIGN OF TOP SLAB

SUPPORT - HOGGING
Depth of member (D) = 500.00 mm
Width of the member (b) = 1000.00 mm

MATERIAL PROPERTIES :
Grade of concrete, fck = 35 MPa
Mean value of concrete compressive strength, fcm = 45 MPa
Grade of Reinforcement = 500 MPa
fywd 0.8 fyk = 400 MPa
Clear cover of top slab = 40 mm
Modulus of Elasticity steel Es = 200000 MPa
For short Term loading Ecm = 32308 MPa
For long Term loading Ecm' = 13728 MPa
fctm = 2.80 MPa
fcteff = Max of 2.9 Mpa or fctm = 2.90 MPa
fcd = 15.75 MPa
Cross sectional Area, Ac = 5.000 m2
Perimeter in contact with atmosphere u = 21.00 m
Notational size ho = 476.19 mm
Age of concrete at the time of loading = 90 days
t∞ considered = 25550 days
Creep factor Φ= 1.3534
εuk = 0.00450
εud = 0.00405
εcu2 = 0.0035
xumax/d = 0.4636

PERMISSIBLE STRESSES
1) Permissble concrete compressive stresses
Load Combination Permissble Stress
SLS Rare 0.48 fck = 16.8 MPa
SLS QP 0.36 fck = 12.6 MPa

2) Permissble Tensile stress in steel (Rare) 0.6 fy = 300 MPa

(QP) 0.8 fy = 400 MPa
3) Permissible crack width wk
SLS QP Load combination = 0.3 mm

Maximum Reinforcement
[ Tension Reinf. ] ≤ 0.025AC At section other than Laps
[ Tension + Compression ] ≤ 0.04AC At any section
Where AC = Gross Cross section Area of Concrete

Minimum Reinforcement :
Ast min = Max [ 0.26 fctm / fyk bt d , 0.0013 bt d ] (Refer IRC:112 clause 16.5.1.1)
bt = Mean width of Tension zone.
 3X10X5.5 BOX CELL

A) ULS CAPACITY CHECK (Top Slab Hogging)

Section Face of Support Face of Haunch Curtailment point Mid Span

Distance from centreline of side wall m 0.250 1.150 3.250 5.250

MED (Hogging) kNm 334.949 182.867 42.483 72.843
Width (b) mm 1000.000 1000.000 1000.000 1000.000
Overall depth D mm 800.000 500.000 500.000 500.000
d mm 752.000 452.000 452.000 452.000
Diameter mm 16 12 16 12 16 0 16 0
Area of steel
Spacing mm 200 200 200 200 200 200 200 200
provided 2
Ast, Provided mm 1570.796 1570.796 1005.310 1005.310
Reinforcement (%) 0.209 0.209 0.209 0.209
xmax mm 348.609 209.536 209.536 209.536
xu = 0.87 fyk Ast / 0.362 fck b mm 53.930 53.930 34.515 34.515
Check UR, OK UR, OK UR, OK UR, OK
Ast,cal =M/ 0.87 fyk (d'-0.416 xu) mm2 1055.419 978.624 223.153 382.628

Check Ast Calc. < Ast Provided < Ast Max OK OK OK OK

Ast min mm2 1128.000 678.000 678.000 678.000
Check Ast,provided > Ast min OK OK OK OK
∆Fd kN 47.115 39.123 21.417 3.809
z = d- 0.416 xu m 729.565 429.565 437.642 437.642
MED/z +∆Fd kN 506.222 464.824 118.488 170.252
MRd =0.87 fyk Ast (d-0.416 xu) kNm 498.509 293.520 191.385 191.385
MRD/z kNm/m 683.296 683.296 437.310 437.310
Check MRD/z > MED/z + ∆Fd OK OK OK OK

Distribution steel at top of top slab: (Refer IRC:112 clause 16.6.1.1)

Distribution Reinforcement : At Least 20% of the main Reinforcement = 314.16 mm2
Provide 12 @ 125 mm c/c = 904.7787 mm2 OK

B) SLS STRESS CHECK

Rare Load combination. Quasi Permanent Load Combination
Ec,eq = Ecm*(MQP+MST) m = Es / Ecm'
MST + (1+ Φ)* MQP
MST = MRARE -MQP
m = Es / Ec,eq
Flexural tensile Strength:
where,

fctm,fl = mean Flexural tensile strength of solid beam

h = total depth of member in mm
 3X10X5.5 BOX CELL

Formula used for calculation of stress

dc (depth of neutral axis) = .-m x As + √ ( m2 x AS2 + 2 x m x As x b x d )
b
INA (Transformed) = bx dc3/3 + m x As x (d - dc)2

Compressive stress in concrete σc = MRARE x dc / INA

Tensile stress in steel σs = m x MRARE x (d - dc ) / INA

Stress Check for SLS Load Combinations

SLS (Rare Combination)
Section Face of Support Face of Haunch Curtailment point Mid Span

Distance from centreline of side wall m 0.250 1.150 3.250 5.250

MED (Hogging) kNm 228.242 122.760 38.670 53.705
Width (b) mm 1000.000 1000.000 1000.000 1000.000
d mm 752.000 452.000 452.000 452.000
Ast, Provided mm2 1570.796 1570.796 1005.310 1005.310
Checking Section: Cracked or Uncracked
I mm4 3.544E+10 7.695E+09 7.695E+09 7.695E+09
Y = d/2 mm 400.000 250.000 250.000 250.000
σ (Stress) Mpa 2.576 3.988 1.256 1.745
fctm,fl Mpa 3.080 3.080 3.080 3.080
Cracked/Uncracked Uncracked Cracked Uncracked Uncracked
Finding Stresses considering Cracked Section
Modular ratio 10.128 9.995 12.917 8.598
N.A. depth (dc) mm 139.591 104.466 96.135 80.172
INA mm4 6.873E+09 2.276E+09 1.941E+09 1.367E+09
Compressive stress Mpa 4.635 5.634 1.916 3.150
Max Compressive Stress Mpa 16.800 16.800 16.800 16.800
Check OK OK OK OK
Tensile stress Mpa 205.967 187.334 91.595 125.616
Maximum Tensile Stress Mpa 400.000 400.000 400.000 400.000
Check OK OK OK OK

SLS (Quasi Permanent Combination)

Section Face of Support Face of Haunch Curtailment point Mid Span

Distance from centreline of side wall m 0.250 1.150 3.250 5.250

MED (Hogging) kNm 107.270 55.753 31.045 15.430
Width (b) mm 1000.000 1000.000 1000.000 1000.000
d mm 752.000 452.000 452.000 452.000
Ast, Provided mm2 1570.796 1570.796 1005.310 1005.310
Checking Section: Cracked or Uncracked
I mm4 3.544E+10 7.695E+09 7.695E+09 7.695E+09
Y = d/2 mm 400.000 250.000 250.000 250.000
σ (Stress) Mpa 1.211 1.811 1.009 0.501
fctm,fl Mpa 3.080 3.080 3.080 3.080
Cracked/Uncracked Uncracked Uncracked Uncracked Uncracked
 3X10X5.5 BOX CELL

Finding Stresses considering Cracked Section

Modular ratio 14.569 14.569 14.569 14.569
N.A. depth (dc) mm 164.043 122.756 101.348 101.348
INA mm4 9.382E+09 3.097E+09 2.148E+09 2.148E+09
Compressive stress Mpa 1.876 2.210 1.465 0.728
Max Compressive Stress Mpa 12.600 12.600 12.600 12.600
Check OK OK OK OK
Tensile stress Mpa 97.933 86.342 73.840 36.700
Maximum Tensile Stress Mpa 400.000 400.000 400.000 400.000
Check OK OK OK OK

C) SLS CRACK WIDTH CHECK (QUASI PERMANENT LOAD COMBINATION)

1) CHECK Ast,min for crack control
Section Face of Support Face of Haunch Curtailment point Mid Span

Distance from centreline of side wall m 0.250 1.150 3.250 5.250

b mm 1000.000 1000.000 1000.000 1000.000

h mm 800.000 500.000 500.000 500.000
d mm 752.000 452.000 452.000 452.000
Act =bh/2 mm2 400000 250000 250000 250000
σs = fyk Mpa 500.000 500.000 500.000 500.000
k 1.000 1.000 1.000 1.000
kc 0.400 0.400 0.400 0.400
As,min =kc k fct,eff Act /σs 2
mm 928 580 580 580
As,provided mm2 1570.80 1570.80 1005.31 1005.31
Check OK OK OK OK

h 0.00 0.30 0.80 3.00

k 1.00 1.00 0.65 0.65

2) CHECK FOR MAXIMUM SPACING b/w bars.

Section Face of Support Face of Haunch Curtailment point Mid Span

Distance from centreline of side wall m 0.250 1.150 3.250 5.250

Bar diameter mm 16 16 16 16
Cover mm 40 40 40 40
Provided mm 100 100 100 100
Spacing b/w
bars Calculated mm 240 240 240 240
Check OK OK OK OK
 3X10X5.5 BOX CELL

3) CHECK FOR CRACK WIDTH ( IRC 112 / clause 10.3.2 (2) )

Section Face of Support Face of Haunch Curtailment point Mid Span

Distance from centreline of side wall m 0.250 1.150 3.250 5.250

hc,eff = Min [2.5 (h - d), (h - x)/3 ,
mm 50.46 96.82 96.82 96.82
h/2]
Aceff = hc,eff x b mm2 50463.58 96821.19 96821.19 96821.19
As provided mm2 1570.80 1570.80 1005.31 1005.31
ρpeff = As/Ac,eff 0.0311 0.0162 0.0104 0.0104
Srmax =3.4c + 0.17 Φ /ρPeff mm 223.38 303.66 397.96 397.96
σsc Mpa 97.93 86.34 73.84 36.70
x = neutral axis depth mm 164.04 122.76 101.35 101.35
kt 0.500 0.500 0.500 0.500
αe = Es/Ecm' 14.57 14.57 14.57 14.57
esm - ecm =Max [ [ σsc - kt fct,eff ( 1+ αe ρP,eff ) /
0.00029 0.00026 0.00022 0.00011
ρP,eff ] /Es , 0.6 σsc/Es ]
wk mm 0.0656 0.0787 0.0882 0.0438
Check OK OK OK OK

D) CHECK FOR SHEAR : ( IRC 112 / clause 10.3.2 (2) )

Check of Shear Reinforcement Requirement
Load combination ULS
Section Face of Support Face of Haunch Curtailment point Mid Span

VED kN 94.23 78.25 42.83 7.62

β 0.5000 1.0000 1.0000 1.0000
βVED kN 47.12 78.25 42.83 7.62
d mm 752.00 452.00 452.00 452.00
bw mm 1000.00 1000.00 1000.00 1000.00
k= Min [ 1 + √200/d , 2 ] 1.516 1.665 1.665 1.665
Asl 2 1570.796 1570.796 1005.310 1005.310
mm
ρ1 = Min [ Asl/bw d , 0.02 ] 0.002 0.003 0.002 0.002
3/2
νmin = 0.031 k fck1/2 0.342 0.394 0.394 0.394
σcp Mpa 0 0 0 0
VRdc =Max [ ( 0.12 k (80 ρ1 fck
)0.33 + 0.15 σcp ) bw d , (νmin kN 257.358 191.368 178.127 179.443
+0.15σcp ) bw d ]
No Shear reinf. No Shear reinf. No Shear reinf. No Shear reinf.
Check
Required Required Required Required
 3X10X5.5 BOX CELL

DESIGN OF SIDE WALL

MIDSPAN - SAGGING
Depth of member (D) = 500.00 mm
Width of the member (b) = 1000.00 mm

MATERIAL PROPERTIES :
Grade of concrete, fck = 35 MPa
Mean value of concrete compressive strength, fcm = 45 MPa
Grade of Reinforcement = 500 MPa
fywd 0.8 fyk = 400 MPa
Clear cover of top slab = 40 mm
Modulus of Elasticity steel Es = 200000 MPa
For short Term loading Ecm = 32308 MPa
For long Term loading Ecm' = 13704 MPa
fctm = 2.80 MPa
fcteff = Max of 2.9 Mpa or fctm = 2.90 MPa
fcd = 15.75 MPa
Cross sectional Area, Ac = 2.750 m2
Perimeter in contact with atmosphere u = 12.00 m
Notational size ho = 458.33 mm
Age of concrete at the time of loading = 90 days
t∞ considered = 25550 days
Creep factor Φ= 1.3576
εuk = 0.00450
εud = 0.00405
εcu2 = 0.0035
xumax/d = 0.4636

PERMISSIBLE STRESSES
1) Permissble concrete compressive stresses
Load Combination Permissble Stress
SLS Rare 0.48 fck = 16.8 MPa
SLS QP 0.36 fck = 12.6 MPa

2) Permissble Tensile stress in steel (Rare) 0.6 fy = 300 MPa

(QP) 0.8 fy = 400 MPa
3) Permissible crack width wk
SLS QP Load combination = 0.3 mm

Maximum Reinforcement
[ Tension Reinf. ] ≤ 0.025AC At section other than Laps
[ Tension + Compression ] ≤ 0.04AC At any section
Where AC = Gross Cross section Area of Concrete

Minimum Reinforcement :
Ast min = Max [ 0.26 fctm / fyk bt d , 0.0013 bt d ] (Refer IRC:112 clause 16.5.1.1)
bt = Mean width of Tension zone.
 3X10X5.5 BOX CELL

A) ULS CAPACITY CHECK (Side Wall Sagging)

Section Mid Span Curtailment point Face of Haunch Face of Support

Distance from centreline of side wall m 3.000 1.775 0.550 0.250

MED (Sagging) kNm 119.065 84.101 21.760 23.263
Width (b) mm 1000.000 1000.000 1000.000 1000.000
Overall depth D mm 500.000 500.000 500.000 500.000
d mm 452.000 452.000 452.000 452.000
Diameter mm 16 0 16 0 16 0 16 0
Area of steel
Spacing mm 200 200 200 200 200 200 200 200
provided
Ast, Provided mm2 1005.310 1005.310 1005.310 1005.310
Reinforcement (%) 0.222 0.222 0.222 0.222
xmax mm 209.536 209.536 209.536 209.536
xu = 0.87 fyk Ast / 0.362 fck b mm 34.515 34.515 34.515 34.515
Check UR, OK UR, OK UR, OK UR, OK
Ast,cal =M/ 0.87 fyk (d'-0.416 xu) mm2 625.426 441.764 114.303 122.194
Ast Max mm2 110000.000 110000.000 110000.000 110000.000
Check Ast Calc. < Ast Provided < Ast Max OK OK OK OK
Ast min mm2 678.000 678.000 678.000 678.000
Check Ast,provided > Ast min OK OK OK OK
∆Fd kN 3.876 33.474 90.928 106.996
z = d- 0.416 xu m 437.642 437.642 437.642 437.642
MRd =0.87 fyk Ast (d-0.416 xu) kNm 191.385 191.385 191.385 191.385
MRD/z kNm/m 437.310 437.310 437.310 437.310
Check MRD/z > MED/z + ∆Fd OK OK OK OK

Distribution steel at innerside of side wall: (Refer IRC:112 clause 16.6.1.1)

Distribution Reinforcement : At Least 20% of the main Reinforcement = 201.06 mm2
Provide 12 @ 125 mm c/c = 904.78 mm2 OK

B) SLS STRESS CHECK

Rare Load combination. Quasi Permanent Load Combination
Ec,eq = Ecm*(MQP+MST) m = Es / Ecm'
MST + (1+ Φ)* MQP
MST = MRARE -MQP
m = Es / Ec,eq
Flexural tensile Strength:
where,

fctm,fl = mean Flexural tensile strength of solid beam

h = total depth of member in mm
 3X10X5.5 BOX CELL

Formula used for calculation of stress

dc (depth of neutral axis) = .-m x As + √ ( m2 x AS2 + 2 x m x As x b x d )
b
INA (Transformed) = bx dc3/3 + m x As x (d - dc)2

Compressive stress in concrete σc = MRARE x dc / INA

Tensile stress in steel σs = m x MRARE x (d - dc ) / INA

Stress Check for SLS Load Combinations

SLS (Rare Combination)
Curtailment
Section Mid Span Face of Haunch Face of Support
point
Distance from centreline of side wall m 3.000 1.775 0.550 0.250
MED (Sagging) kNm 97.799 73.538 19.817 21.475
Width (b) mm 1000.000 1000.000 1000.000 1000.000
d mm 452.000 452.000 452.000 452.000
Ast, Provided mm2 1005.310 1005.310 1005.310 1005.310
Checking Section: Cracked or Uncracked
I mm4 7.695E+09 7.695E+09 7.695E+09 7.695E+09
Y = d/2 mm 250.000 250.000 250.000 250.000
σ (Stress) Mpa 3.177 2.389 0.644 0.698
fctm,fl Mpa 3.080 3.080 3.080 3.080
Cracked/Uncracked Cracked Uncracked Uncracked Uncracked
Finding Stresses considering Cracked Section
Modular ratio 13.078 13.649 12.946 13.195
N.A. depth (dc) mm 96.661 98.494 96.230 97.043
INA mm4 1.961E+09 2.033E+09 1.944E+09 1.976E+09
Compressive stress Mpa 4.820 3.562 0.981 1.055
Max Compressive Stress Mpa 16.800 16.800 16.800 16.800
Check OK OK OK OK
Tensile stress Mpa 231.746 174.511 46.942 50.903
Maximum Tensile Stress Mpa 400.000 400.000 400.000 400.000
Check OK OK OK OK

SLS (Quasi Permanent Combination)

Curtailment
Section Mid Span Face of Haunch Face of Support
point
Distance from centreline of side wall m 3.000 1.775 0.550 0.250
MED (Sagging) kNm 80.149 65.263 15.929 17.900
Width (b) mm 1000.000 1000.000 1000.000 1000.000
d mm 452.000 452.000 452.000 452.000
Ast, Provided mm2 1005.310 1005.310 1005.310 1005.310
Checking Section: Cracked or Uncracked
I mm4 7.695E+09 7.695E+09 7.695E+09 7.695E+09
Y = d/2 mm 250.000 250.000 250.000 250.000
σ (Stress) Mpa 2.604 2.120 0.517 0.582
fctm,fl Mpa 3.080 3.080 3.080 3.080
Cracked/Uncracked Uncracked Uncracked Uncracked Uncracked
 3X10X5.5 BOX CELL

Finding Stresses considering Cracked Section

Modular ratio 14.594 14.594 14.594 14.594
N.A. depth (dc) mm 101.426 101.426 101.426 101.426
INA mm4 2.151E+09 2.151E+09 2.151E+09 2.151E+09
Compressive stress Mpa 3.779 3.077 0.751 0.844
Max Compressive Stress Mpa 12.600 12.600 12.600 12.600
Check OK OK OK OK
Tensile stress Mpa 190.644 155.236 37.889 42.577
Maximum Tensile Stress Mpa 400.000 400.000 400.000 400.000
Check OK OK OK OK

C) SLS CRACK WIDTH CHECK (QUASI PERMANENT LOAD COMBINATION)

1) CHECK Ast,min for crack control
Curtailment
Section Mid Span Face of Haunch Face of Support
point
Distance from centreline of side wall m 3.000 1.775 0.550 0.250

b mm 1000.000 1000.000 1000.000 1000.000

h mm 500.000 500.000 500.000 500.000
d mm 452.000 452.000 452.000 452.000
Act =bh/2 mm2 250000 250000 250000 250000
σs = fyk Mpa 500.000 500.000 500.000 500.000
k 1.000 1.000 1.000 1.000
kc 0.400 0.400 0.400 0.400
As,min =kc k fct,eff Act /σs 2
mm 580 580 580 580
As,provided 2
mm 1005.31 1005.31 1005.31 1005.31
Check OK OK OK OK

h 0.00 0.30 0.80 3.00

k 1.00 1.00 0.65 0.65

2) CHECK FOR MAXIMUM SPACING b/w bars.

Curtailment
Section Mid Span Face of Haunch Face of Support
point
Distance from centreline of side wall m 3.000 1.775 0.550 0.250
Bar diameter mm 16 16 16 16
Cover mm 40 40 40 40
Provided mm 200 200 200 200
Spacing b/w
bars Calculated mm 240 240 240 240
Check OK OK OK OK
 3X10X5.5 BOX CELL

3) CHECK FOR CRACK WIDTH ( IRC 112 / clause 10.3.2 (2) )

Curtailment
Section Mid Span Face of Haunch Face of Support
point
Distance from centreline of side wall m 3.000 1.775 0.550 0.250
hc,eff = Min [2.5 (h - d), (h - x)/3 ,
mm 96.82 96.82 96.82 96.82
h/2]
Aceff = hc,eff x b mm2 96821.19 96821.19 96821.19 96821.19
As provided mm2 1005.31 1005.31 1005.31 1005.31
ρpeff = As/Ac,eff 0.0104 0.0104 0.0104 0.0104
Srmax =3.4c + 0.17 Φ /ρPeff mm 397.96 397.96 397.96 397.96
σsc Mpa 190.64 155.24 37.89 42.58
x = neutral axis depth mm 101.43 101.43 101.43 101.43
kt 0.500 0.500 0.500 0.500
αe = Es/Ecm' 14.59 14.59 14.59 14.59
esm - ecm =Max [ [ σsc - kt fct,eff ( 1+ αe ρP,eff ) /
0.00057 0.00047 0.00011 0.00013
ρP,eff ] /Es , 0.6 σsc/Es ]
wk mm 0.2276 0.1853 0.0452 0.0508
Check OK OK OK OK

D) CHECK FOR SHEAR : ( IRC 112 / clause 10.3.2 (2) )

Check of Shear Reinforcement Requirement
Load combination ULS
Curtailment
Section Mid Span Face of Haunch Face of Support
point
VED kN 7.75 66.95 181.86 213.99
β 1.000 1.000 0.608 0.500
βVED kN 7.75 66.95 110.64 107.00
d mm 452.00 452.00 452.00 452.00
bw mm 1000.00 1000.00 1000.00 1000.00
k= Min [ 1 + √200/d , 2 ] 1.665 1.665 1.665 1.665
Asl 2 1005.310 1005.310 1005.310 1005.310
mm
ρ1 = Min [ Asl/bw d , 0.02 ] 0.002 0.002 0.002 0.002
3/2
νmin = 0.031 k fck1/2 0.394 0.394 0.394 0.394
σcp Mpa 0 0 0 0
VRdc =Max [ ( 0.12 k (80 ρ1 fck
)0.33 + 0.15 σcp ) bw d , (νmin kN 178.127 178.127 178.127 179.443
+0.15σcp ) bw d ]
No Shear reinf. No Shear reinf. No Shear reinf. No Shear reinf.
Check
Required Required Required Required
 3X10X5.5 BOX CELL

DESIGN OF SIDE WALL

SUPPORT - HOGGING
Depth of member (D) = 500.00 mm
Width of the member (b) = 1000.00 mm

MATERIAL PROPERTIES :
Grade of concrete, fck = 35 MPa
Mean value of concrete compressive strength, fcm = 45 MPa
Grade of Reinforcement = 500 MPa
fywd 0.8 fyk = 400 MPa
Clear cover of top slab = 75 mm
Modulus of Elasticity steel Es = 200000 MPa
For short Term loading Ecm = 32308 MPa
For long Term loading Ecm' = 13704 MPa
fctm = 2.80 MPa
fcteff = Max of 2.9 Mpa or fctm = 2.90 MPa
fcd = 15.75 MPa
Cross sectional Area, Ac = 2.750 m2
Perimeter in contact with atmosphere u = 12.00 m
Notational size ho = 458.33 mm
Age of concrete at the time of loading = 90 days
t∞ considered = 25550 days
Creep factor Φ= 1.3576
εuk = 0.00450
εud = 0.00405
εcu2 = 0.0035
xumax/d = 0.4636

PERMISSIBLE STRESSES
1) Permissble concrete compressive stresses
Load Combination Permissble Stress
SLS Rare 0.48 fck = 16.8 MPa
SLS QP 0.36 fck = 12.6 MPa

2) Permissble Tensile stress in steel (Rare) 0.6 fy = 300 MPa

(QP) 0.8 fy = 400 MPa
3) Permissible crack width wk
SLS QP Load combination = 0.3 mm

Maximum Reinforcement
[ Tension Reinf. ] ≤ 0.025AC At section other than Laps
[ Tension + Compression ] ≤ 0.04AC At any section
Where AC = Gross Cross section Area of Concrete

Minimum Reinforcement :
Ast min = Max [ 0.26 fctm / fyk bt d , 0.0013 bt d ] (Refer IRC:112 clause 16.5.1.1)
bt = Mean width of Tension zone.
 3X10X5.5 BOX CELL

A) ULS CAPACITY CHECK (Side Wall Hogging)

Section Face of Support Face of Haunch Curtailment point Mid Span

Distance from centreline of side wall m 0.250 0.550 1.775 3.000

MED (Hogging) kNm 195.782 140.084 125.769 159.412
Width (b) mm 1000.000 1000.000 1000.000 1000.000
Overall depth D mm 800.000 500.000 500.000 500.000
d mm 717.000 417.000 417.000 417.000
Diameter mm 16 12 16 12 16 0 16 0
Area of steel
Spacing mm 200 200 200 200 200 200 200 200
provided
Ast, Provided mm2 1570.796 1570.796 1005.310 1005.310
Reinforcement (%) 0.219 0.219 0.219 0.219
xmax mm 332.384 193.311 193.311 193.311
xu = 0.87 fyk Ast / 0.362 fck b mm 53.930 53.930 34.515 34.515
Check UR, OK UR, OK UR, OK UR, OK
Ast,cal =M/ 0.87 fyk (d'-0.416 xu) mm2 647.992 816.170 718.065 910.152
Ast Max mm2 110000.000 110000.000 110000.000 110000.000
Check Ast Calc. < Ast Provided < Ast Max OK OK OK OK
Ast min mm2 1075.500 625.500 625.500 625.500
Check Ast,provided > Ast min OK OK OK OK
∆Fd kN 106.996 90.928 33.474 3.876
MED/z +∆Fd kN 388.872 445.962 345.832 399.792
MRd =0.87 fyk Ast (d-0.416 xu) kNm 474.594 269.605 176.079 176.079
MRD/z kNm/m 683.296 683.296 437.310 437.310
Check MRD/z > MED/z + ∆Fd OK OK OK OK

Distribution steel at outer side of side wall: (Refer IRC:112 clause 16.6.1.1)
Distribution Reinforcement : At Least 20% of the main Reinforcement = 314.16 mm2
Provide 12 @ 125 mm c/c = 904.779 mm2 OK

B) SLS STRESS CHECK

Rare Load combination. Quasi Permanent Load Combination
Ec,eq = Ecm*(MQP+MST) m = Es / Ecm'
MST + (1+ Φ)* MQP
MST = MRARE -MQP
m = Es / Ec,eq
Flexural tensile Strength:
where,

fctm,fl = mean Flexural tensile strength of solid beam

h = total depth of member in mm
 3X10X5.5 BOX CELL

Formula used for calculation of stress

dc (depth of neutral axis) = .-m x As + √ ( m2 x AS2 + 2 x m x As x b x d )
b
INA (Transformed) = bx dc3/3 + m x As x (d - dc)2

Compressive stress in concrete σc = MRARE x dc / INA

Tensile stress in steel σs = m x MRARE x (d - dc ) / INA

Stress Check for SLS Load Combinations

SLS (Rare Combination)
Section Face of Support Face of Haunch Curtailment point Face of Support

Distance from centreline of side wallm 0.250 0.550 1.775 3.000

MED (Hogging) kNm 132.903 95.974 87.255 110.509
Width (b) mm 1000.000 1000.000 1000.000 1000.000
d mm 717.000 417.000 417.000 417.000
Ast, Provided mm2 1570.796 1570.796 1005.310 1005.310
Checking Section: Cracked or Uncracked
I mm4 3.072E+10 6.043E+09 6.043E+09 6.043E+09
Y = d/2 mm 400.000 250.000 250.000 250.000
σ (Stress) Mpa 1.731 3.971 3.610 4.572
fctm,fl Mpa 3.080 3.080 3.080 3.080
Cracked/Uncracked Uncracked Cracked Cracked Cracked
Finding Stresses considering Cracked Section
Modular ratio 11.196 10.373 9.826 9.738
N.A. depth (dc) mm 142.191 101.413 81.425 81.096
INA mm4 6.769E+09 1.971E+09 1.292E+09 1.282E+09
Compressive stress Mpa 2.792 4.939 5.497 6.989
Max Compressive Stress Mpa 16.800 16.800 16.800 16.800
Check OK OK OK OK
Tensile stress Mpa 126.356 159.446 222.630 281.882
Maximum Tensile Stress Mpa 300.000 300.000 300.000 300.000
Check OK OK OK OK

SLS (Quasi Permanent Combination)

Section Face of Support Face of Haunch Curtailment point Mid Span

Distance from centreline of side wall

m 0.250 0.550 1.775 3.000
MED (Hogging) kNm 79.163 47.770 37.751 46.646
Width (b) mm 1000.000 1000.000 1000.000 1000.000
d mm 717.000 417.000 417.000 417.000
Ast, Provided mm2 1570.796 1570.796 1005.310 1005.310
Checking Section: Cracked or Uncracked
I mm4 3.072E+10 6.043E+09 6.043E+09 6.043E+09
Y = d/2 mm 400.000 250.000 250.000 250.000
σ (Stress) Mpa 1.031 1.976 1.562 1.930
fctm,fl Mpa 3.080 3.080 3.080 3.080
Cracked/Uncracked Uncracked Uncracked Uncracked Uncracked
 3X10X5.5 BOX CELL

Finding Stresses considering Cracked Section

Modular ratio 14.594 14.594 14.594 14.594
N.A. depth (dc) mm 159.831 117.235 96.915 96.915
INA mm4 8.478E+09 2.597E+09 1.807E+09 1.807E+09
Compressive stress Mpa 1.492 2.156 2.025 2.502
Max Compressive Stress Mpa 12.600 12.600 12.600 12.600
Check OK OK OK OK
Tensile stress Mpa 75.930 80.470 97.614 120.614
Maximum Tensile Stress Mpa 400.000 400.000 400.000 400.000
Check OK OK OK OK

C) SLS CRACK WIDTH CHECK (QUASI PERMANENT LOAD COMBINATION)

1) CHECK Ast,min for crack control
Section Face of Support Face of Haunch Curtailment point Mid Span

Distance from centreline of side wall m 0.250 0.550 1.775 3.000

b mm 1000.000 1000.000 1000.000 1000.000

h mm 800.000 500.000 500.000 500.000
d mm 717.000 417.000 417.000 417.000
Act =bh/2 mm2 400000 250000 250000 250000
σs = fyk Mpa 500.000 500.000 500.000 500.000
k 1.000 1.000 1.000 1.000
kc 0.400 0.400 0.400 0.400
As,min =kc k fct,eff Act /σs 2
mm 928 580 580 580
As,provided 2
mm 1570.80 1570.80 1005.31 1005.31
Check OK OK OK OK

h 0.00 0.30 0.80 3.00

k 1.00 1.00 0.65 0.65

2) CHECK FOR MAXIMUM SPACING b/w bars.

Section Face of Support Face of Haunch Curtailment point Mid Span

Distance from centreline of side wall m 0.250 0.550 1.775 3.000

Bar diameter mm 16 16 16 16
Cover mm 75 75 75 75
Provided mm 200 200 200 200
Spacing b/w
bars Calculated mm 415 415 415 415
Check OK OK OK OK
 3X10X5.5 BOX CELL

3) CHECK FOR CRACK WIDTH ( IRC 112 / clause 10.3.2 (2) )

Section Face of Support Face of Haunch Curtailment point Mid Span

Distance from centreline of side wall m 0.250 0.550 1.775 3.000

hc,eff = Min [2.5 (h - d), (h - x)/3 ,
mm 55.87 102.23 102.23 102.23
h/2]
Aceff = hc,eff x b mm2 55871.96 102229.58 102229.58 102229.58
As provided mm2 1570.80 1570.80 1005.31 1005.31
ρpeff = As/Ac,eff 0.0281 0.0154 0.0098 0.0098
Srmax =3.4c + 0.17 Φ /ρPeff mm 351.75 432.02 531.60 531.60
σsc Mpa 75.93 80.47 97.61 120.61
x = neutral axis depth mm 159.83 117.24 96.91 96.91
kt 0.500 0.500 0.500 0.500
αe = Es/Ecm' 14.59 14.59 14.59 14.59
esm - ecm =Max [ [ σsc - kt fct,eff ( 1+ αe ρP,eff ) /
0.00023 0.00024 0.00029 0.00036
ρP,eff ] /Es , 0.6 σsc/Es ]
wk mm 0.0801 0.1043 0.1557 0.1924
Check OK OK OK OK

D) CHECK FOR SHEAR : ( IRC 112 / clause 10.3.2 (2) )

Check of Shear Reinforcement Requirement
Load combination ULS
Section Face of Support Face of Haunch Curtailment point Mid Span

VED kN 213.99 181.86 66.95 7.75

β 0.5000 0.6595 1.0000 1.0000
βVED kN 107.00 119.93 66.95 7.75
d mm 717.00 417.00 417.00 417.00
bw mm 1000.00 1000.00 1000.00 1000.00
k= Min [ 1 + √200/d , 2 ] 1.528 1.693 1.693 1.693
Asl 2 1570.796 1570.796 1005.310 1005.310
mm
ρ1 = Min [ Asl/bw d , 0.02 ] 0.002 0.004 0.002 0.002
3/2
νmin = 0.031 k fck1/2 0.346 0.404 0.404 0.404
σcp Mpa 0 0 0 0
VRdc =Max [ ( 0.12 k (80 ρ1 fck
)0.33 + 0.15 σcp ) bw d , (νmin kN 248.406 184.287 168.400 172.803
+0.15σcp ) bw d ]
No Shear reinf. No Shear reinf. No Shear reinf. No Shear reinf.
Check
Required Required Required Required
 3X10X5.5 BOX CELL

DESIGN OF BOTTOM SLAB

MIDSPAN - SAGGING
Depth of member (D) = 500.00 mm
Width of the member (b) = 1000.00 mm

MATERIAL PROPERTIES :
Grade of concrete, fck = 35 MPa
Mean value of concrete compressive strength, fcm = 45 MPa
Grade of Reinforcement = 500 MPa
fywd 0.8 fyk = 400 MPa
Clear cover of top slab = 40 mm
Modulus of Elasticity steel Es = 200000 MPa
For short Term loading Ecm = 32308 MPa
For long Term loading Ecm' = 13728 MPa
fctm = 2.80 MPa
fcteff = Max of 2.9 Mpa or fctm = 2.90 MPa
fcd = 15.75 MPa
Cross sectional Area, Ac = 5.000 m2
Perimeter in contact with atmosphere u = 21.00 m
Notational size ho = 476.19 mm
Age of concrete at the time of loading = 90 days
t∞ considered = 25550 days
Creep factor Φ= 1.3534
εuk = 0.00450
εud = 0.00405
εcu2 = 0.0035
xumax/d = 0.4636

PERMISSIBLE STRESSES
1) Permissble concrete compressive stresses
Load Combination Permissble Stress
SLS Rare 0.48 fck = 16.8 MPa
SLS QP 0.36 fck = 12.6 MPa

2) Permissble Tensile stress in steel (Rare) 0.6 fy = 300 MPa

(QP) 0.8 fy = 400 MPa
3) Permissible crack width wk
SLS QP Load combination = 0.3 mm

Maximum Reinforcement
[ Tension Reinf. ] ≤ 0.025AC At section other than Laps
[ Tension + Compression ] ≤ 0.04AC At any section
Where AC = Gross Cross section Area of Concrete

Minimum Reinforcement :
Ast min = Max [ 0.26 fctm / fyk bt d , 0.0013 bt d ] (Refer IRC:112 clause 16.5.1.1)
bt = Mean width of Tension zone.
 3X10X5.5 BOX CELL

A) ULS CAPACITY CHECK (Bottom Slab Sagging)

Section Mid Span Curtailment point Face of Haunch Face of Support

Distance from centreline of side wall m 5.250 3.250 1.150 0.250

MED (Sagging) kNm 66.755 102.753 96.141 36.523
Width (b) mm 1000.000 1000.000 1000.000 1000.000
Overall depth D mm 500.000 500.000 500.000 500.000
d mm 452.000 452.000 452.000 452.000
Diameter mm 16 12 16 12 16 0 16 0
Area of steel
Spacing mm 200 200 200 200 200 200 200 200
provided
Ast, Provided mm2 1570.796 1570.796 1005.310 1005.310
Reinforcement (%) 0.348 0.348 0.348 0.348
xmax mm 209.536 0.000 209.536 209.536
xu = 0.87 fyk Ast / 0.362 fck b mm 53.930 53.930 34.515 34.515
Check UR, OK OR,Revise UR, OK UR, OK
Ast,cal =M/ 0.87 fyk (d'-0.416 xu) mm2 357.246 549.891 505.012 191.850
Ast Max mm2 200000.000 200000.000 200000.000 200000.000
Ast Calc. < Ast Provided < Ast Max OK OK OK OK
Ast min mm2 678.000 678.000 678.000 678.000
Check Ast,provided > Ast min OK OK OK OK
∆Fd kN 2.977 25.464 46.175 52.729
MED/z +∆Fd kN 158.378 264.666 265.855 136.183
MRd =0.87 fyk Ast (d-0.416 xu) kNm 293.520 293.520 191.385 191.385
MRD/z kNm/m 683.296 683.296 437.310 437.310
Check MRD/z > MED/z + ∆Fd OK OK OK OK

Distribution steel at top of bottom slab: (Refer IRC:112 clause 16.6.1.1)

Distribution Reinforcement : At Least 20% of the main Reinforcement = 314.16 mm2
Provide 12 @ 125 mm c/c = 904.78 mm2 OK

B) SLS STRESS CHECK

Rare Load combination. Quasi Permanent Load Combination
Ec,eq = Ecm*(MQP+MST) m = Es / Ecm'
MST + (1+ Φ)* MQP
MST = MRARE -MQP
m = Es / Ec,eq
Flexural tensile Strength:
where,

fctm,fl = mean Flexural tensile strength of solid beam

h = total depth of member in mm
Formula used for calculation of stress
 3X10X5.5 BOX CELL

dc (depth of neutral axis) = .-m x As + √ ( m2 x AS2 + 2 x m x As x b x d )

b
INA (Transformed) = b x dc3/3 + m x As x (d - dc)2

Compressive stress in concrete σc = MRARE x dc / INA

Tensile stress in steel σs = m x MRARE x (d - dc ) / INA

Stress Check for SLS Load Combinations

SLS (Rare Combination)
Curtailment
Section Mid Span Face of Haunch Face of Support
point
Distance from centreline of side wall m 5.250 3.250 1.150 0.250
MED (Sagging) kNm 46.574 71.505 66.657 31.055
Width (b) mm 1000.000 1000.000 1000.000 1000.000
d mm 452.000 452.000 452.000 452.000
Ast, Provided mm2 1570.796 1570.796 1005.310 1005.310
Checking Section: Cracked or Uncracked
I mm4 7.695E+09 7.695E+09 7.695E+09 7.695E+09
Y = d/2 mm 250.000 250.000 250.000 250.000
σ (Stress) Mpa 1.513 2.323 2.165 1.009
fctm,fl Mpa 3.080 3.080 3.080 3.080
Cracked/Uncracked Uncracked Uncracked Uncracked Uncracked
Finding Stresses considering Cracked Section
Modular ratio 10.550 10.068 9.934 11.618
N.A. depth (dc) mm 106.943 104.797 85.554 91.736
INA mm4 2.381E+09 2.290E+09 1.550E+09 1.773E+09
Compressive stress Mpa 2.092 3.272 3.680 1.607
Max Compressive Stress Mpa 16.800 16.800 16.800 16.800
Check OK OK OK OK
Tensile stress Mpa 71.213 109.147 156.570 73.301
Maximum Tensile Stress Mpa 400.000 400.000 400.000 400.000
Check OK OK OK OK

SLS (Quasi Permanent Combination)

Curtailment
Section Mid Span Face of Haunch Face of Support
point
Distance from centreline of side wall m 5.250 3.250 1.150 0.250
MED (Sagging) kNm 24.236 33.097 29.786 20.117
Width (b) mm 1000.000 1000.000 1000.000 1000.000
d mm 452.000 452.000 452.000 452.000
Ast, Provided mm2 1570.796 1570.796 1005.310 1005.310
Checking Section: Cracked or Uncracked
I mm4 7.695E+09 7.695E+09 7.695E+09 7.695E+09
Y = d/2 mm 250.000 250.000 250.000 250.000
σ (Stress) Mpa 0.787 1.075 0.968 0.654
fctm,fl Mpa 3.080 3.080 3.080 3.080
Cracked/Uncracked Uncracked Uncracked Uncracked Uncracked
 3X10X5.5 BOX CELL

Finding Stresses considering Cracked Section

Modular ratio 14.569 14.569 14.569 14.569
N.A. depth (dc) mm 122.756 122.756 101.348 101.348
INA mm4 3.097E+09 3.097E+09 2.148E+09 2.148E+09
Compressive stress Mpa 0.961 1.312 1.405 0.949
Max Compressive Stress Mpa 12.600 12.600 12.600 12.600
Check OK OK OK OK
Tensile stress Mpa 37.533 51.256 70.845 47.848
Maximum Tensile Stress Mpa 400.000 400.000 400.000 400.000
Check OK OK OK OK

C) SLS CRACK WIDTH CHECK (QUASI PERMANENT LOAD COMBINATION)

1) CHECK Ast,min for crack control
Curtailment
Section Mid Span Face of Haunch Face of Support
point
Distance from centreline of side wall m 5.250 3.250 1.150 0.250

b mm 1000.000 1000.000 1000.000 1000.000

h mm 500.000 500.000 500.000 500.000
d mm 452.000 452.000 452.000 452.000
Act =bh/2 mm2 250000 250000 250000 250000
σs = fyk Mpa 500.000 500.000 500.000 500.000
k 1.000 1.000 1.000 1.000
kc 0.400 0.400 0.400 0.400
As,min =kc k fct,eff Act /σs 2
mm 580 580 580 580
As,provided 2
mm 1570.80 1570.80 1005.31 1005.31
Check OK OK OK OK

h 0.00 0.30 0.80 3.00

k 1.00 1.00 0.65 0.65

2) CHECK FOR MAXIMUM SPACING b/w bars.

Curtailment
Section Mid Span Face of Haunch Face of Support
point
Distance from centreline of side wall m 5.250 3.250 1.150 0.250
Bar diameter mm 16 16 16 16
Cover mm 40 40 40 40
Provided mm 200 200 200 200
Spacing b/w
bars Calculated mm 240 240 240 240
Check OK OK OK OK
 3X10X5.5 BOX CELL

3) CHECK FOR CRACK WIDTH ( IRC 112 / clause 10.3.2 (2) )

Curtailment
Section Mid Span Face of Haunch Face of Support
point
Distance from centreline of side wall m 5.250 3.250 1.150 0.250
hc,eff = Min [2.5 (h - d), (h - x)/3 ,
mm 96.82 120.00 96.82 96.82
h/2]
Aceff = hc,eff x b mm2 96821.19 120000.00 96821.19 96821.19
As provided mm2 1570.80 1570.80 1005.31 1005.31
ρpeff = As/Ac,eff 0.0162 0.0131 0.0104 0.0104
Srmax =3.4c + 0.17 Φ /ρPeff mm 303.66 343.79 397.96 397.96
σsc Mpa 37.53 51.26 70.85 47.85
x = neutral axis depth mm 122.76 122.76 101.35 101.35
kt 0.500 0.500 0.500 0.500
αe = Es/Ecm' 14.57 14.57 14.57 14.57
esm - ecm =Max [ [ σsc - kt fct,eff ( 1+ αe ρP,eff ) /
0.00011 0.00015 0.00021 0.00014
ρP,eff ] /Es , 0.6 σsc/Es ]
wk mm 0.0342 0.0529 0.0846 0.0571
Check OK OK OK OK

D) CHECK FOR SHEAR : ( IRC 112 / clause 10.3.2 (2) )

Check of Shear Reinforcement Requirement
Load combination ULS
Curtailment
Section Mid Span Face of Haunch Face of Support
point
VED kN 5.95 50.93 92.35 105.46
β 1.000 1.000 1.000 0.500
βVED kN 5.95 50.93 92.35 52.73
d mm 452.00 452.00 452.00 452.00
bw mm 1000.00 1000.00 1000.00 1000.00
k= Min [ 1 + √200/d , 2 ] 1.665 1.665 1.665 1.665
Asl 2 1570.796 1570.796 1005.310 1005.310
mm
ρ1 = Min [ Asl/bw d , 0.02 ] 0.003 0.003 0.002 0.002
3/2
νmin = 0.031 k fck1/2 0.394 0.394 0.394 0.394
σcp Mpa 0 0 0 0
VRdc =Max [ ( 0.12 k (80 ρ1 fck
)0.33 + 0.15 σcp ) bw d , (νmin kN 191.368 191.368 178.127 179.443
+0.15σcp ) bw d ]
No Shear reinf. No Shear reinf. No Shear reinf. No Shear reinf.
Check
Required Required Required Required
 3X10X5.5 BOX CELL

DESIGN OF BOTTOM SLAB

SUPPORT - HOGGING
Depth of member (D) = 500.00 mm
Width of the member (b) = 1000.00 mm

MATERIAL PROPERTIES :
Grade of concrete, fck = 35 MPa
Mean value of concrete compressive strength, fcm = 45 MPa
Grade of Reinforcement = 500 MPa
fywd 0.8 fyk = 400 MPa
Clear cover of top slab = 40 mm
Modulus of Elasticity steel Es = 200000 MPa
For short Term loading Ecm = 32308 MPa
For long Term loading Ecm' = 13728 MPa
fctm = 2.80 MPa
fcteff = Max of 2.9 Mpa or fctm = 2.90 MPa
fcd = 15.75 MPa
Cross sectional Area, Ac = 5.000 m2
Perimeter in contact with atmosphere u = 21.00 m
Notational size ho = 476.19 mm
Age of concrete at the time of loading = 90 days
t∞ considered = 25550 days
Creep factor Φ= 1.3534
εuk = 0.00450
εud = 0.00405
εcu2 = 0.0035
xumax/d = 0.4636

PERMISSIBLE STRESSES
1) Permissble concrete compressive stresses
Load Combination Permissble Stress
SLS Rare 0.48 fck = 16.8 MPa
SLS QP 0.36 fck = 12.6 MPa

2) Permissble Tensile stress in steel (Rare) 0.6 fy = 300 MPa

(QP) 0.8 fy = 400 MPa
3) Permissible crack width wk
SLS QP Load combination = 0.3 mm

Maximum Reinforcement
[ Tension Reinf. ] ≤ 0.025AC At section other than Laps
[ Tension + Compression ] ≤ 0.04AC At any section
Where AC = Gross Cross section Area of Concrete

Minimum Reinforcement :
Ast min = Max [ 0.26 fctm / fyk bt d , 0.0013 bt d ] (Refer IRC:112 clause 16.5.1.1)
bt = Mean width of Tension zone.
 3X10X5.5 BOX CELL

A) ULS CAPACITY CHECK (Top Slab Hogging)

Section Face of Support Face of Haunch Curtailment point Mid Span

Distance from centreline of side wall m 0.250 1.150 3.250 5.250

MED (Hogging) kNm 196.832 112.356 22.963 2.600
Width (b) mm 1000.000 1000.000 1000.000 1000.000
Overall depth D mm 800.000 500.000 500.000 500.000
d mm 752.000 452.000 452.000 452.000
Diameter mm 16 12 16 12 16 0 16 0
Area of steel
Spacing mm 200 200 200 200 200 200 200 200
provided
Ast, Provided mm2 1570.796 1570.796 1005.310 1005.310
Reinforcement (%) 0.209 0.209 0.209 0.209
xmax mm 348.609 209.536 209.536 209.536
xu = 0.87 fyk Ast / 0.362 fck b mm 53.930 53.930 34.515 34.515
Check UR, OK UR, OK UR, OK UR, OK
Ast,cal =M/ 0.87 fyk (d'-0.416 xu) mm2 620.214 601.283 120.622 13.657
Ast Max mm2 200000.000 200000.000 200000.000 200000.000
Check Ast Calc. < Ast Provided < Ast Max OK OK OK OK
Ast min mm2 1128.000 678.000 678.000 678.000

Check Ast,provided > Ast min OK OK OK OK

z = d- 0.416 xu m 729.565 429.565 437.642 437.642
MED/z +∆Fd kN 322.521 307.733 77.934 8.917
MRd =0.87 fyk Ast (d-0.416 xu) kNm 498.509 293.520 191.385 191.385
MRD/z kNm/m 683.296 683.296 437.310 437.310
Check MRD/z > MED/z + ∆Fd OK OK OK OK

Distribution steel at bottom of bottom slab: (Refer IRC:112 clause 16.6.1.1)

Distribution Reinforcement : At Least 20% of the main Reinforcement = 314.16 mm2
Provide 12 @ 125 mm c/c = 904.7787 mm2 OK

B) SLS STRESS CHECK

Rare Load combination. Quasi Permanent Load Combination
Ec,eq = Ecm*(MQP+MST) m = Es / Ecm'
MST + (1+ Φ)* MQP
MST = MRARE -MQP
m = Es / Ec,eq
Flexural tensile Strength:
where,

fctm,fl = mean Flexural tensile strength of solid beam

h = total depth of member in mm
 3X10X5.5 BOX CELL

Formula used for calculation of stress

dc (depth of neutral axis) = .-m x As + √ ( m2 x AS2 + 2 x m x As x b x d )
b
INA (Transformed) = bx dc3/3 + m x As x (d - dc)2

Compressive stress in concrete σc = MRARE x dc / INA

Tensile stress in steel σs = m x MRARE x (d - dc ) / INA

Stress Check for SLS Load Combinations

SLS (Rare Combination)
Section Face of Support Face of Haunch Curtailment point Mid Span

Distance from centreline of side wallm 0.250 1.150 3.250 5.250

MED (Hogging) kNm 131.987 80.660 20.820 1.950
Width (b) mm 1000.000 1000.000 1000.000 1000.000
d mm 752.000 452.000 452.000 452.000
Ast, Provided mm2 1570.796 1570.796 1005.310 1005.310
Checking Section: Cracked or Uncracked
I mm4 3.544E+10 7.695E+09 7.695E+09 7.695E+09
Y = d/2 mm 400.000 250.000 250.000 250.000
σ (Stress) Mpa 1.490 2.620 0.676 0.063
fctm,fl Mpa 3.080 3.080 3.080 3.080
Cracked/Uncracked Uncracked Uncracked Uncracked Uncracked
Finding Stresses considering Cracked Section
Modular ratio 12.003 12.872 12.843 8.983
N.A. depth (dc) mm 150.590 116.480 95.894 81.774
INA mm4 7.958E+09 2.803E+09 1.931E+09 1.420E+09
Compressive stress Mpa 2.498 3.352 1.034 0.112
Max Compressive Stress Mpa 16.800 16.800 16.800 16.800
Check OK OK OK OK
Tensile stress Mpa 119.728 124.281 49.304 4.567
Maximum Tensile Stress Mpa 400.000 400.000 400.000 400.000
Check OK OK OK OK

SLS (Quasi Permanent Combination)

Section Face of Support Face of Haunch Curtailment point Mid Span

Distance from centreline of side wall

m 0.250 1.150 3.250 5.250
MED (Hogging) kNm 91.562 64.322 16.532 0.650
Width (b) mm 1000.000 1000.000 1000.000 1000.000
d mm 752.000 452.000 452.000 452.000
Ast, Provided mm2 1570.796 1570.796 1005.310 1005.310
Checking Section: Cracked or Uncracked
I mm4 3.544E+10 7.695E+09 7.695E+09 7.695E+09
Y = d/2 mm 400.000 250.000 250.000 250.000
σ (Stress) Mpa 1.033 2.090 0.537 0.021
fctm,fl Mpa 3.080 3.080 3.080 3.080
Cracked/Uncracked Uncracked Uncracked Uncracked Uncracked
 3X10X5.5 BOX CELL

Finding Stresses considering Cracked Section

Modular ratio 14.569 14.569 14.569 14.569
N.A. depth (dc) mm 164.043 122.756 101.348 101.348
INA mm4 9.382E+09 3.097E+09 2.148E+09 2.148E+09
Compressive stress Mpa 1.601 2.549 0.780 0.031
Max Compressive Stress Mpa 12.600 12.600 12.600 12.600
Check OK OK OK OK
Tensile stress Mpa 83.592 99.612 39.321 1.546
Maximum Tensile Stress Mpa 400.000 400.000 400.000 400.000
Check OK OK OK OK

C) SLS CRACK WIDTH CHECK (QUASI PERMANENT LOAD COMBINATION)

1) CHECK Ast,min for crack control
Section Face of Support Face of Haunch Curtailment point Mid Span

Distance from centreline of side wall m 0.250 1.150 3.250 5.250

b mm 1000.000 1000.000 1000.000 1000.000

h mm 800.000 500.000 500.000 500.000
d mm 752.000 452.000 452.000 452.000
Act =bh/2 mm2 400000 250000 250000 250000
σs = fyk Mpa 500.000 500.000 500.000 500.000
k 1.000 1.000 1.000 1.000
kc 0.400 0.400 0.400 0.400
As,min =kc k fct,eff Act /σs 2
mm 928 580 580 580
As,provided 2
mm 1570.80 1570.80 1005.31 1005.31
Check OK OK OK OK

h 0.00 0.30 0.80 3.00

k 1.00 1.00 0.65 0.65

2) CHECK FOR MAXIMUM SPACING b/w bars.

Section Face of Support Face of Haunch Curtailment point Mid Span

Distance from centreline of side wall m 0.250 1.150 3.250 5.250

Bar diameter mm 16 16 16 16
Cover mm 40 40 40 40
Provided mm 200 200 200 200
Spacing b/w
bars Calculated mm 240 240 240 240
Check OK OK OK OK
 3X10X5.5 BOX CELL

3) CHECK FOR CRACK WIDTH ( IRC 112 / clause 10.3.2 (2) )

Section Face of Support Face of Haunch Curtailment point Mid Span

Distance from centreline of side wall m 0.250 1.150 3.250 5.250

hc,eff = Min [2.5 (h - d), (h - x)/3 ,
mm 50.46 96.82 96.82 96.82
h/2]
Aceff = hc,eff x b mm2 50463.58 96821.19 96821.19 96821.19
As provided mm2 1570.80 1570.80 1005.31 1005.31
ρpeff = As/Ac,eff 0.0311 0.0162 0.0104 0.0104
Srmax =3.4c + 0.17 Φ /ρPeff mm 223.38 303.66 397.96 397.96
σsc Mpa 83.59 99.61 39.32 1.55
x = neutral axis depth mm 164.04 122.76 101.35 101.35
kt 0.500 0.500 0.500 0.500
αe = Es/Ecm' 14.57 14.57 14.57 14.57
esm - ecm =Max [ [ σsc - kt fct,eff ( 1+ αe ρP,eff ) /
0.00025 0.00030 0.00012 0.00000
ρP,eff ] /Es , 0.6 σsc/Es ]
wk mm 0.0560 0.0907 0.0469 0.0018
Check OK OK OK OK

D) CHECK FOR SHEAR : ( IRC 112 / clause 10.3.2 (2) )

Check of Shear Reinforcement Requirement
Load combination ULS
Section Face of Support Face of Haunch Curtailment point Mid Span

VED kN 360.00 249.00 159.00 89.00

β 0.5000 1.0000 1.0000 1.0000
βVED kN 180.00 249.00 159.00 89.00
d mm 752.00 452.00 452.00 452.00
bw mm 1000.00 1000.00 1000.00 1000.00
k= Min [ 1 + √200/d , 2 ] 1.516 1.665 1.665 1.665
Asl 2 1570.796 1570.796 1005.310 1005.310
mm
ρ1 = Min [ Asl/bw d , 0.02 ] 0.002 0.003 0.002 0.002
3/2
νmin = 0.031 k fck1/2 0.342 0.394 0.394 0.394
σcp Mpa 0 0 0 0
VRdc =Max [ ( 0.12 k (80 ρ1 fck
)0.33 + 0.15 σcp ) bw d , (νmin kN 257.358 191.368 178.127 179.443
+0.15σcp ) bw d ]
No Shear reinf. Provide shear No Shear reinf. No Shear reinf.
Check
Required reinf. Required Required
 3X10X5.5 BOX CELL

Check for Maximum Shear Capacity :

Section Face of Support Face of Haunch Curtailment point Mid Span

Distance from centreline of side wall m 0.250 1.150 3.250 5.250

VED kN 105.46 92.35 50.93 5.95
bw mm 1000.00 1000.00 1000.00 1000.00
d mm 752.00 452.00 452.00 452.00
z = 0.9d mm 676.8 406.8 406.8 406.8
αcw 1.000 1.000 1.000 1.000
ν1 0.600 0.600 0.600 0.600
Vrd max = αcw * bw * z *ν1 * fcd /2 kN 3197.88 1922.13 1922.13 1922.13
Check OK OK OK OK
-1
θ = 0.5 sin [ 2*VNS/(αcw* bw* z*
deg 0.94 1.38 0.76 0.09
v1* fcd)]
θ adopted deg 45 45 45 45
∆Fd = 0.5 VED cot θ kN 52.7285 46.175 25.464 2.9765
∆Fd = Additional Tensile force, to be accounted in longitudinal reinforcement
Design tensile strength of stirrups Mpa 435 435 435 435
Diameter of stirrups mm 10 10 10 10
Type of stirrups legged 1 1 1 1
Area of one stirrups mm2 78.5 78.5 78.5 78.5
Maximum spacing of stirrups in long. Direction, Cl 16.5.2
sl.max (0.75d) mm 564.0 564.0 564.0 564.0
Maximum spacing of stirrups in Trans. Direction, Cl 16.5.2
sl.max 0.75d ≤ 600 mm mm 564 564 564 564
Spacing of stirrups considered in
longitudinal & transverse mm 200 200 200 200
Check OK OK OK OK
Number of stirrups per width of slab in transverse direction
No. 5.0 5.0 5.0 5.0
Total area of stirrups per m width
of slab in transverse direction mm2 392.5 392.5 392.5 392.5
Minimum shear reinforcement,Ref 10.3.3.5 of IRC 112
Shear resistance of stirrups,Cl KN 1605.05 964.74 964.74 964.74
Check OK OK OK OK
 3X10X5.5 BOX CELL

DESIGN OF SIDE WALL

MIDSPAN - SAGGING
Depth of member (D) = 400.00 mm
Width of the member (b) = 1000.00 mm

MATERIAL PROPERTIES :
Grade of concrete, fck = 35 MPa
Mean value of concrete compressive strength, fcm = 45 MPa
Grade of Reinforcement = 500 MPa
fywd 0.8 fyk = 400 MPa
Clear cover of top slab = 40 mm
Modulus of Elasticity steel Es = 200000 MPa
For short Term loading Ecm = 32308 MPa
For long Term loading Ecm' = 13704 MPa
fctm = 2.80 MPa
fcteff = Max of 2.9 Mpa or fctm = 2.90 MPa
fcd = 15.75 MPa
Cross sectional Area, Ac = 2.750 m2
Perimeter in contact with atmosphere u = 12.00 m
Notational size ho = 458.33 mm
Age of concrete at the time of loading = 90 days
t∞ considered = 25550 days
Creep factor Φ= 1.3576
εuk = 0.00450
εud = 0.00405
εcu2 = 0.0035
xumax/d = 0.4636

PERMISSIBLE STRESSES
1) Permissble concrete compressive stresses
Load Combination Permissble Stress
SLS Rare 0.48 fck = 16.8 MPa
SLS QP 0.36 fck = 12.6 MPa

2) Permissble Tensile stress in steel (Rare) 0.6 fy = 300 MPa

(QP) 0.8 fy = 400 MPa
3) Permissible crack width wk
SLS QP Load combination = 0.3 mm

Maximum Reinforcement
[ Tension Reinf. ] ≤ 0.025AC At section other than Laps
[ Tension + Compression ] ≤ 0.04AC At any section
Where AC = Gross Cross section Area of Concrete

Minimum Reinforcement :
Ast min = Max [ 0.26 fctm / fyk bt d , 0.0013 bt d ] (Refer IRC:112 clause 16.5.1.1)
bt = Mean width of Tension zone.
 3X10X5.5 BOX CELL

A) ULS CAPACITY CHECK (Side Wall Sagging)

Section Mid Span Curtailment point Face of Haunch Face of Support

Distance from centreline of side wall m 3.000 1.775 0.550 0.250

MED (Sagging) kNm 55.539 94.082 72.100 84.088
Width (b) mm 1000.000 1000.000 1000.000 1000.000
Overall depth D mm 400.000 400.000 400.000 400.000
d mm 352.000 352.000 352.000 352.000
Diameter mm 16 0 16 0 16 0 16 0
Area of steel
Spacing mm 200 200 200 200 200 200 200 200
provided
Ast, Provided mm2 1005.310 1005.310 1005.310 1005.310
Reinforcement (%) 0.286 0.286 0.286 0.286
xmax mm 163.179 163.179 163.179 163.179
xu = 0.87 fyk Ast / 0.362 fck b mm 34.515 34.515 34.515 34.515
Check UR, OK UR, OK UR, OK UR, OK
Ast,cal =M/ 0.87 fyk (d'-0.416 xu) mm2 378.138 640.559 490.893 572.519

Check Ast Calc. < Ast Provided < Ast Max OK OK OK OK

Ast min 2
mm 528.000 528.000 528.000 528.000
Check Ast,provided > Ast min OK OK OK OK
∆Fd kN 4.983 4.983 4.983 4.983
z = d- 0.416 xu m 337.642 337.642 337.642 337.642
MED/z +∆Fd kN 169.473 283.626 218.522 254.029
MRd =0.87 fyk Ast (d-0.416 xu) kNm 147.654 147.654 147.654 147.654
MRD/z kNm/m 437.310 437.310 437.310 437.310
Check MRD/z > MED/z + ∆Fd OK OK OK OK

Distribution steel at innerside of side wall: (Refer IRC:112 clause 16.6.1.1)

Distribution Reinforcement : At Least 20% of the main Reinforcement = 201.06 mm2
Provide 10 @ 150 mm c/c = 523.6 mm2 OK

B) SLS STRESS CHECK

Rare Load combination. Quasi Permanent Load Combination
Ec,eq = Ecm*(MQP+MST) m = Es / Ecm'
MST + (1+ Φ)* MQP
MST = MRARE -MQP
m = Es / Ec,eq
Flexural tensile Strength:
where,

fctm,fl = mean Flexural tensile strength of solid beam

h = total depth of member in mm
Formula used for calculation of stress
dc (depth of neutral axis) = .-m x As + √ ( m2 x AS2 + 2 x m x As x b x d )
b
INA (Transformed) = b x dc3/3 + m x As x (d - dc)2

Compressive stress in concrete σc = MRARE x dc / INA

Tensile stress in steel σs = m x MRARE x (d - dc ) / INA
 3X10X5.5 BOX CELL

Stress Check for SLS Load Combinations

SLS (Rare Combination)
Curtailment
Section Mid Span Face of Haunch Face of Support
point
Distance from centreline of side wall m 3.000 1.775 0.550 0.250
MED (Sagging) kNm 38.308 72.494 56.162 65.070
Width (b) mm 1000.000 1000.000 1000.000 1000.000
d mm 352.000 352.000 352.000 352.000
Ast, Provided mm2 1005.310 1005.310 1005.310 1005.310
Checking Section: Cracked or Uncracked
I mm4 3.635E+09 3.635E+09 3.635E+09 3.635E+09
Y = d/2 mm 200.000 200.000 200.000 200.000
σ (Stress) Mpa 2.108 3.989 3.090 3.581
fctm,fl Mpa 3.360 3.360 3.360 3.360
Cracked/Uncracked Uncracked Cracked Uncracked Cracked
Finding Stresses considering Cracked Section
Modular ratio 7.034 9.589 9.825 9.682
N.A. depth (dc) mm 63.838 73.303 74.092 73.614
INA mm4 6.739E+08 8.801E+08 8.984E+08 8.873E+08
Compressive stress Mpa 3.629 6.038 4.632 5.399
Max Compressive Stress Mpa 16.800 16.800 16.800 16.800
Check OK OK OK OK
Tensile stress Mpa 115.219 220.142 170.684 197.659
Maximum Tensile Stress Mpa 400.000 400.000 400.000 400.000
Check OK OK OK OK

SLS (Quasi Permanent Combination)

Curtailment
Section Mid Span Face of Haunch Face of Support
point
Distance from centreline of side wall m 3.000 1.775 0.550 0.250
MED (Sagging) kNm 3.845 29.319 24.287 27.032
Width (b) mm 1000.000 1000.000 1000.000 1000.000
d mm 352.000 352.000 352.000 352.000
Ast, Provided mm2 1005.310 1005.310 1005.310 1005.310
Checking Section: Cracked or Uncracked
I mm4 3.635E+09 3.635E+09 3.635E+09 3.635E+09
Y = d/2 mm 200.000 200.000 200.000 200.000
σ (Stress) Mpa 0.212 1.613 1.336 1.488
fctm,fl Mpa 3.360 3.360 3.360 3.360
Cracked/Uncracked Uncracked Uncracked Uncracked Uncracked
Finding Stresses considering Cracked Section
Modular ratio 14.594 14.594 14.594 14.594
N.A. depth (dc) mm 88.013 88.013 88.013 88.013
INA mm4 1.250E+09 1.250E+09 1.250E+09 1.250E+09
Compressive stress Mpa 0.271 2.065 1.710 1.904
Max Compressive Stress Mpa 12.600 12.600 12.600 12.600
Check OK OK OK OK
Tensile stress Mpa 11.854 90.386 74.873 83.336
Maximum Tensile Stress Mpa 400.000 400.000 400.000 400.000
Check OK OK OK OK
 3X10X5.5 BOX CELL

C) SLS CRACK WIDTH CHECK (QUASI PERMANENT LOAD COMBINATION)

1) CHECK Ast,min for crack control
Curtailment
Section Mid Span Face of Haunch Face of Support
point
Distance from centreline of side wall m 3.000 1.775 0.550 0.250

b mm 1000.000 1000.000 1000.000 1000.000

h mm 400.000 400.000 400.000 400.000
d mm 352.000 352.000 352.000 352.000
Act =bh/2 2
mm 200000 200000 200000 200000
σs = fyk Mpa 500.000 500.000 500.000 500.000
k 1.000 1.000 1.000 1.000
kc 0.400 0.400 0.400 0.400
As,min =kc k fct,eff Act /σs 2
mm 464 464 464 464
As,provided 2
mm 1005.31 1005.31 1005.31 1005.31
Check OK OK OK OK

h 0.00 0.30 0.80 3.00

k 1.00 1.00 0.65 0.65

2) CHECK FOR MAXIMUM SPACING b/w bars.

Curtailment
Section Mid Span Face of Haunch Face of Support
point
Distance from centreline of side wall m 3.000 1.775 0.550 0.250
Bar diameter mm 16 16 16 16
Cover mm 40 40 40 40
Provided mm 200 200 200 200
Spacing b/w
bars Calculated mm 240 240 240 240
Check OK OK OK OK

3) CHECK FOR CRACK WIDTH ( IRC 112 / clause 10.3.2 (2) )

Curtailment
Section Mid Span Face of Haunch Face of Support
point
Distance from centreline of side wall m 3.000 1.775 0.550 0.250
hc,eff = Min [2.5 (h - d), (h - x)/3 ,
mm 78.94 78.94 78.94 78.94
h/2]
Aceff = hc,eff x b mm2 78940.40 78940.40 78940.40 78940.40
As provided mm2 1005.31 1005.31 1005.31 1005.31
ρpeff = As/Ac,eff 0.0127 0.0127 0.0127 0.0127
Srmax =3.4c + 0.17 Φ /ρPeff mm 349.58 349.58 349.58 349.58
σsc Mpa 11.85 90.39 74.87 83.34
x = neutral axis depth mm 88.01 88.01 88.01 88.01
kt 0.500 0.500 0.500 0.500
αe = Es/Ecm' 14.59 14.59 14.59 14.59
esm - ecm =Max [ [ σsc - kt fct,eff ( 1+ αe ρP,eff ) /
0.00004 0.00027 0.00022 0.00025
ρP,eff ] /Es , 0.6 σsc/Es ]
wk mm 0.0124 0.0948 0.0785 0.0874
Check OK OK OK OK
 3X10X5.5 BOX CELL

D) CHECK FOR SHEAR : ( IRC 112 / clause 10.3.2 (2) )

Check of Shear Reinforcement Requirement
Load combination ULS
Curtailment
Section Mid Span Face of Haunch Face of Support
point
VED kN 9.97 9.97 9.97 9.97
β 1.000 1.000 0.781 0.500
βVED kN 9.97 9.97 7.79 4.98
d mm 352.00 352.00 352.00 352.00
bw mm 1000.00 1000.00 1000.00 1000.00
k= Min [ 1 + √200/d , 2 ] 1.754 1.754 1.754 1.754
Asl 2 1005.310 1005.310 1005.310 1005.310
mm
ρ1 = Min [ Asl/bw d , 0.02 ] 0.003 0.003 0.003 0.003
νmin = 0.031 k3/2 fck1/2 0.426 0.426 0.426 0.426
σcp Mpa 0 0 0 0
VRdc =Max [ ( 0.12 k (80 ρ1 fck
)0.33 + 0.15 σcp ) bw d , (νmin kN 149.934 149.934 149.934 159.837
+0.15σcp ) bw d ]
No Shear reinf. No Shear reinf. No Shear reinf. No Shear reinf.
Check
Required Required Required Required
 3X10X5.5 BOX CELL

DESIGN OF SIDE WALL

SUPPORT - HOGGING
Depth of member (D) = 400.00 mm
Width of the member (b) = 1000.00 mm

MATERIAL PROPERTIES :
Grade of concrete, fck = 35 MPa
Mean value of concrete compressive strength, fcm = 45 MPa
Grade of Reinforcement = 500 MPa
fywd 0.8 fyk = 400 MPa
Clear cover of top slab = 40 mm
Modulus of Elasticity steel Es = 200000 MPa
For short Term loading Ecm = 32308 MPa
For long Term loading Ecm' = 13704 MPa
fctm = 2.80 MPa
fcteff = Max of 2.9 Mpa or fctm = 2.90 MPa
fcd = 15.75 MPa
Cross sectional Area, Ac = 2.750 m2
Perimeter in contact with atmosphere u = 12.00 m
Notational size ho = 458.33 mm
Age of concrete at the time of loading = 90 days
t∞ considered = 25550 days
Creep factor Φ= 1.3576
εuk = 0.00450
εud = 0.00405
εcu2 = 0.0035
xumax/d = 0.4636

PERMISSIBLE STRESSES
1) Permissble concrete compressive stresses
Load Combination Permissble Stress
SLS Rare 0.48 fck = 16.8 MPa
SLS QP 0.36 fck = 12.6 MPa

2) Permissble Tensile stress in steel (Rare) 0.6 fy = 300 MPa

(QP) 0.8 fy = 400 MPa
3) Permissible crack width wk
SLS QP Load combination = 0.3 mm

Maximum Reinforcement
[ Tension Reinf. ] ≤ 0.025AC At section other than Laps
[ Tension + Compression ] ≤ 0.04AC At any section
Where AC = Gross Cross section Area of Concrete

Minimum Reinforcement :
Ast min = Max [ 0.26 fctm / fyk bt d , 0.0013 bt d ] (Refer IRC:112 clause 16.5.1.1)
bt = Mean width of Tension zone.
 3X10X5.5 BOX CELL

A) ULS CAPACITY CHECK (Side Wall Hogging)

Curtailment
Section Face of Support Face of Haunch Mid Span
point
Distance from centreline of side wall m 0.250 0.525 1.900 0.702
MED (Hogging) kNm 159.438 136.764 44.570 34.588
Width (b) mm 1000.000 1000.000 1000.000 1000.000
Overall depth D mm 400.000 400.000 400.000 400.000
d mm 352.000 352.000 352.000 352.000
Diameter mm 16 12 16 12 16 0 16 0
Area of steel
Spacing mm 200 200 200 200 200 200 200 200
provided
Ast, Provided mm2 1570.796 1570.796 1005.310 1005.310
Reinforcement (%) 0.446 0.446 0.446 0.446
xmax mm 163.179 163.179 163.179 163.179
xu = 0.87 fyk Ast / 0.362 fck b mm 53.930 53.930 34.515 34.515
Check UR, OK UR, OK UR, OK UR, OK
Ast,cal =M/ 0.87 fyk (d'-0.416 xu) mm2 1112.147 953.985 303.455 235.494

Check Ast Calc. < Ast Provided < Ast Max OK OK OK OK

Ast min 2
mm 528.000 528.000 528.000 528.000
Check Ast,provided > Ast min OK OK OK OK
∆Fd kN 4.983 4.983 4.983 4.983
z = d- 0.416 xu m 329.565 329.565 337.642 337.642
MED/z +∆Fd kN 488.767 419.966 136.986 107.423
MRd =0.87 fyk Ast (d-0.416 xu) kNm 225.191 225.191 147.654 147.654
MRD/z kNm/m 683.296 683.296 437.310 437.310
Check MRD/z > MED/z + ∆Fd OK OK OK OK

Distribution steel at outer side of side wall: (Refer IRC:112 clause 16.6.1.1)
Distribution Reinforcement : At Least 20% of the main Reinforcement = 314.16 mm2
Provide 12 @ 100 mm c/c = 1131 mm2 OK

B) SLS STRESS CHECK

Rare Load combination. Quasi Permanent Load Combination
Ec,eq = Ecm*(MQP+MST) m = Es / Ecm'
MST + (1+ Φ)* MQP
MST = MRARE -MQP
m = Es / Ec,eq
Flexural tensile Strength:
where,

fctm,fl = mean Flexural tensile strength of solid beam

h = total depth of member in mm
Formula used for calculation of stress
dc (depth of neutral axis) = .-m x As + √ ( m2 x AS2 + 2 x m x As x b x d )
b
INA (Transformed) = b x dc3/3 + m x As x (d - dc)2

Compressive stress in concrete σc = MRARE x dc / INA

Tensile stress in steel σs = m x MRARE x (d - dc ) / INA
 3X10X5.5 BOX CELL

Stress Check for SLS Load Combinations

SLS (Rare Combination)
Curtailment
Section Face of Support Face of Haunch Mid Span
point
Distance from centreline of side wall m 0.250 0.525 1.900 0.702
MED (Hogging) kNm 105.784 90.767 29.708 23.458
Width (b) mm 1000.000 1000.000 1000.000 1000.000
d mm 352.000 352.000 352.000 352.000
Ast, Provided mm2 1570.796 1570.796 1005.310 1005.310
Checking Section: Cracked or Uncracked
I mm4 3.635E+09 3.635E+09 3.635E+09 3.635E+09
Y = d/2 mm 200.000 200.000 200.000 200.000
σ (Stress) Mpa 5.821 4.995 1.635 1.291
fctm,fl Mpa 3.360 3.360 3.360 3.360
Cracked/Uncracked Cracked Cracked Uncracked Uncracked
Finding Stresses considering Cracked Section
Modular ratio 8.553 8.647 10.000 7.765
N.A. depth (dc) mm 84.741 85.144 74.673 66.735
INA mm4 1.162E+09 1.173E+09 9.120E+08 7.343E+08
Compressive stress Mpa 7.712 6.588 2.432 2.132
Max Compressive Stress Mpa 16.800 16.800 16.800 16.800
Check OK OK OK OK
Tensile stress Mpa 208.010 178.556 90.339 70.762
Maximum Tensile Stress Mpa 400.000 400.000 400.000 400.000
Check OK OK OK OK

SLS (Quasi Permanent Combination)

Curtailment
Section Face of Support Face of Haunch Mid Span
point
Distance from centreline of side wall m 0.250 0.525 1.900 0.702
MED (Hogging) kNm 29.736 26.536 13.467 4.395
Width (b) mm 1000.000 1000.000 1000.000 1000.000
d mm 352.000 352.000 352.000 352.000
Ast, Provided mm2 1570.796 1570.796 1005.310 1005.310
Checking Section: Cracked or Uncracked
I mm4 3.635E+09 3.635E+09 3.635E+09 3.635E+09
Y = d/2 mm 200.000 200.000 200.000 200.000
σ (Stress) Mpa 1.636 1.460 0.741 0.242
fctm,fl Mpa 3.360 3.360 3.360 3.360
Cracked/Uncracked Uncracked Uncracked Uncracked Uncracked
Finding Stresses considering Cracked Section
Modular ratio 14.594 14.594 14.594 14.594
N.A. depth (dc) mm 106.167 106.167 88.013 88.013
INA mm4 1.784E+09 1.784E+09 1.250E+09 1.250E+09
Compressive stress Mpa 1.769 1.579 0.948 0.310
Max Compressive Stress Mpa 12.600 12.600 12.600 12.600
Check OK OK OK OK
Tensile stress Mpa 59.791 53.357 41.517 13.549
Maximum Tensile Stress Mpa 400.000 400.000 400.000 400.000
Check OK OK OK OK
 3X10X5.5 BOX CELL

C) SLS CRACK WIDTH CHECK (QUASI PERMANENT LOAD COMBINATION)

1) CHECK Ast,min for crack control
Curtailment
Section Face of Support Face of Haunch Mid Span
point
Distance from centreline of side wall m 0.250 0.525 1.900 0.702

b mm 1000.000 1000.000 1000.000 1000.000

h mm 400.000 400.000 400.000 400.000
d mm 352.000 352.000 352.000 352.000
Act =bh/2 2
mm 200000 200000 200000 200000
σs = fyk Mpa 500.000 500.000 500.000 500.000
k 1.000 1.000 1.000 1.000
kc 0.400 0.400 0.400 0.400
As,min =kc k fct,eff Act /σs 2
mm 464 464 464 464
As,provided 2
mm 1570.80 1570.80 1005.31 1005.31
Check OK OK OK OK

h 0.00 0.30 0.80 3.00

k 1.00 1.00 0.65 0.65

2) CHECK FOR MAXIMUM SPACING b/w bars.

Curtailment
Section Face of Support Face of Haunch Mid Span
point
Distance from centreline of side wall m 0.250 0.525 1.900 0.702
Bar diameter mm 16 16 16 16
Cover mm 40 40 40 40
Provided mm 200 200 200 200
Spacing b/w
bars Calculated mm 240 240 240 240
Check OK OK OK OK

3) CHECK FOR CRACK WIDTH ( IRC 112 / clause 10.3.2 (2) )

Curtailment
Section Face of Support Face of Haunch Mid Span
point
Distance from centreline of side wall m 0.250 0.525 1.900 0.702
hc,eff = Min [2.5 (h - d), (h - x)/3 ,
mm 78.94 78.94 78.94 78.94
h/2]
Aceff = hc,eff x b mm2 78940.40 78940.40 78940.40 78940.40
As provided mm2 1570.80 1570.80 1005.31 1005.31
ρpeff = As/Ac,eff 0.0199 0.0199 0.0127 0.0127
Srmax =3.4c + 0.17 Φ /ρPeff mm 272.69 272.69 349.58 349.58
σsc Mpa 59.79 53.36 41.52 13.55
x = neutral axis depth mm 106.17 106.17 88.01 88.01
kt 0.500 0.500 0.500 0.500
αe = Es/Ecm' 14.59 14.59 14.59 14.59
esm - ecm =Max [ [ σsc - kt fct,eff ( 1+ αe ρP,eff ) /
0.00018 0.00016 0.00012 0.00004
ρP,eff ] /Es , 0.6 σsc/Es ]
wk mm 0.0489 0.0437 0.0435 0.0142
Check OK OK OK OK
 3X10X5.5 BOX CELL

D) CHECK FOR SHEAR : ( IRC 112 / clause 10.3.2 (2) )

Check of Shear Reinforcement Requirement
Load combination ULS
Curtailment
Section Face of Support Face of Haunch Mid Span
point
VED kN 9.97 9.97 9.97 9.97
β 0.5000 0.7457 1.0000 0.9972
βVED kN 4.98 7.43 9.97 9.94
d mm 352.00 352.00 352.00 352.00
bw mm 1000.00 1000.00 1000.00 1000.00
k= Min [ 1 + √200/d , 2 ] 1.754 1.754 1.754 1.754
Asl 2 1570.796 1570.796 1005.310 1005.310
mm
ρ1 = Min [ Asl/bw d , 0.02 ] 0.004 0.004 0.003 0.003
νmin = 0.031 k3/2 fck1/2 0.426 0.426 0.426 0.426
σcp Mpa 0 0 0 0
VRdc =Max [ ( 0.12 k (80 ρ1 fck
)0.33 + 0.15 σcp ) bw d , (νmin kN 170.460 170.460 149.934 159.837
+0.15σcp ) bw d ]
No Shear reinf. No Shear reinf. No Shear reinf. No Shear reinf.
Check
Required Required Required Required
 3X10X5.5 BOX CELL

Calculation of Base Pressure

Load Factor for Base Pressure

IRC 6:2014 Table 3.4 Column 2

Permanent Loads (Dead Load, SIDL except Surfacing = 1

Surfacing = 1
Live Load(Leading Load) = 1

Overall Span of Box = 17.750 m

Box Barrel Length Considered = 12.500 m
Unit Weight of Concrete = 25.000 kN/m3

1) Self Weight of Box:

Box cross sectional area = 25.630 m2
Total Box Weight = 8009.375 kN
Factored Total Weight of Box = 8009.375 kN

2) SIDL (Wearing Coat,Crash Barrier, Footpath etc)

Earth Fill/Wearing Coat = 1.232 kN/m2
Crash Barrier = 20.000 kN/m
Width of Crash Barrier = 0.500 m
Total Weight of Wearing Coat over box = 273.350 kN
Total Weight of Crash barrier = 710.000 kN
Total SIDL = 983.350 kN
Factored SIDL Load = 983.350 kN

3) Live Load
(70R Bogie Load) = 400.000 kN
Factored Live Load = 400.000 kN
Maximum Eccentricity of LL from c/l of carriageway = 2.405 m
Eccentric Moment in Transverse Direction = 962 kNm
Inertia of base about Longitudinal axis = 2888.997 m4
Area of Base = 221.875 m2

Maximum Base Pressure due to Live Load = 400.000 + 962 x 6.25

221.875 2888.997
= 3.88 kN/m2
= 4.85 kN/m2 (Increased by 25%)

Maximum Base Pressure due to DL = 8009.375 = 36.099 kN/m2

221.875

Maximum Base Pressure due to SIDL = 983.350 = 4.432 kN/m2

221.875

Total Base Pressure = 45.39 kN/m2 < 100.00 kN/m2

SAFE
STAAD ULS Temperature Leading

STAAD PLANE
START JOB INFORMATION
ENGINEER DATE 20-08-2021
END JOB INFORMATION
INPUT WIDTH 79
UNIT METER KN
JOINT COORDINATES
1 0 0 0; 2 0.25 0 0; 3 1.15 0 0; 4 3.2 0 0; 5 5.25 0 0; 6 7.3 0 0; 7 9.35 0 0;
8 10.25 0 0; 9 10.5 0 0; 11 0.25 6 0; 12 1.15 6 0; 13 3.2 6 0; 14 5.25 6 0;
15 7.3 6 0; 16 9.35 6 0; 17 10.25 6 0; 18 10.5 6 0; 20 0 0.25 0; 21 0 0.55 0;
22 0 1.775 0; 23 0 3 0; 24 0 4.225 0; 25 0 5.45 0; 26 0 5.75 0; 27 0 6 0;
28 10.5 0.25 0; 29 10.5 0.55 0; 30 10.5 1.775 0; 31 10.5 3 0; 32 10.5 4.225 0;
33 10.5 5.45 0; 34 10.5 5.75 0; 36 10.75 0 0; 37 11.65 0 0; 38 13.7 0 0;
39 15.75 0 0; 40 17.8 0 0; 41 19.85 0 0; 42 20.75 0 0; 43 21 0 0; 45 10.75 6 0;
46 11.65 6 0; 47 13.7 6 0; 48 15.75 6 0; 49 17.8 6 0; 50 19.85 6 0;
51 20.75 6 0; 52 21 6 0; 54 21 0.25 0; 55 21 0.55 0; 56 21 1.775 0; 57 21 3 0;
58 21 4.225 0; 59 21 5.45 0; 60 21 5.75 0; 62 21.25 0 0; 63 22.15 0 0;
64 24.2 0 0; 65 26.25 0 0; 66 28.3 0 0; 67 30.35 0 0; 68 31.25 0 0;
69 31.5 0 0; 80 31.5 0.25 0; 81 31.5 0.55 0; 82 31.5 1.775 0; 83 31.5 3 0;
84 31.5 4.225 0; 85 31.5 5.45 0; 86 31.5 5.75 0; 87 31.5 6 0; 88 21.25 6 0;
89 22.15 6 0; 90 24.2 6 0; 91 26.25 6 0; 92 28.3 6 0; 93 30.35 6 0;
94 31.25 6 0;
MEMBER INCIDENCES
1 27 11; 2 11 12; 3 12 13; 4 13 14; 5 14 15; 6 15 16; 7 16 17; 8 17 18;
9 18 34; 10 34 33; 11 33 32; 12 32 31; 13 31 30; 14 30 29; 15 29 28; 16 28 9;
17 9 8; 18 8 7; 19 7 6; 20 6 5; 21 5 4; 22 4 3; 23 3 2; 24 2 1; 25 1 20;
26 20 21; 27 21 22; 28 22 23; 29 23 24; 30 24 25; 31 25 26; 32 26 27; 33 18 45;
34 45 46; 35 46 47; 36 47 48; 37 48 49; 38 49 50; 39 50 51; 40 51 52; 41 52 88;
42 88 89; 43 89 90; 44 90 91; 45 91 92; 46 92 93; 47 93 94; 48 94 87; 49 87 86;
50 86 85; 51 85 84; 52 84 83; 53 83 82; 54 82 81; 55 81 80; 56 80 69; 57 69 68;
58 68 67; 59 67 66; 60 66 65; 61 65 64; 62 64 63; 63 63 62; 64 62 43; 65 43 42;
66 42 41; 67 41 40; 68 40 39; 69 39 38; 70 38 37; 71 37 36; 72 36 9; 73 43 54;
74 54 55; 75 55 56; 76 56 57; 77 57 58; 78 58 59; 79 59 60; 80 60 52;
MEMBER PROPERTY INDIAN
1 8 33 40 41 48 PRIS YD 0.8 ZD 1
2 7 34 39 42 47 PRIS YD 0.65 ZD 1
3 TO 6 35 TO 38 43 TO 46 PRIS YD 0.5 ZD 1
11 TO 14 75 TO 78 PRIS YD 0.4 ZD 1
10 31 50 79 PRIS YD 0.95 ZD 1
27 TO 30 51 TO 54 PRIS YD 0.5 ZD 1
17 24 57 64 65 72 PRIS YD 0.8 ZD 1
18 23 58 63 66 71 PRIS YD 0.65 ZD 1
19 TO 22 59 TO 62 67 TO 70 PRIS YD 0.5 ZD 1
15 26 55 74 PRIS YD 0.95 ZD 1
9 16 25 32 49 56 73 80 PRIS YD 1.4 ZD 1
DEFINE MATERIAL START
ISOTROPIC CONCRETE
E 2.21467e+006
POISSON 0.17
DENSITY 2.40262
ALPHA 1e-005
DAMP 0.05
G 946439
TYPE CONCRETE
STRENGTH FCU 2812.28
END DEFINE MATERIAL
CONSTANTS
MATERIAL CONCRETE ALL
SUPPORTS
1 FIXED BUT FZ MX MY MZ KFY 416.667
9 FIXED BUT FX FZ MX MY MZ KFY 416.667
2 8 36 42 62 68 FIXED BUT FX FZ MX MY MZ KFY 1916.67
3 7 FIXED BUT FX FZ MX MY MZ KFY 4916.67
4 TO 6 FIXED BUT FX FZ MX MY MZ KFY 6833.33
1 FIXED BUT FZ MX MY MZ KFY 416.667
43 FIXED BUT FX FZ MX MY MZ KFY 416.667
37 41 FIXED BUT FX FZ MX MY MZ KFY 4916.67
38 TO 40 FIXED BUT FX FZ MX MY MZ KFY 6833.33
1 FIXED BUT FZ MX MY MZ KFY 416.667
69 FIXED BUT FX FZ MX MY MZ KFY 416.667
2 8 FIXED BUT FX FZ MX MY MZ KFY 1916.67
63 67 FIXED BUT FX FZ MX MY MZ KFY 4916.67
64 TO 66 FIXED BUT FX FZ MX MY MZ KFY 6833.33
LOAD 1 SELFWEIGHT
SELFWEIGHT Y -1
LOAD 2 SIDL
MEMBER LOAD
1 TO 8 33 TO 48 UNI GY -10
LOAD 3 SIDL (WC + EARTH FILL )
MEMBER LOAD
1 TO 8 33 TO 48 UNI GY -1.23
LOAD 4 REST EP (IN DRY CONDITION)
MEMBER LOAD
25 TRAP GX 65.56 63.06
26 TRAP GX 63.06 60.56
27 TRAP GX 60.56 45.31
28 TRAP GX 45.31 33.06
29 TRAP GX 33.06 20.81
30 TRAP GX 20.81 8.56
31 TRAP GX 8.56 5.56
32 TRAP GX 5.56 3.06
56 TRAP GX -63.06 -65.56
55 TRAP GX -60.56 -63.06
54 TRAP GX -45.31 -60.56
53 TRAP GX -33.06 -45.31
52 TRAP GX -20.81 -33.06
51 TRAP GX -8.56 -20.81
50 TRAP GX -5.56 -8.56
49 TRAP GX -3.06 -5.56
LOAD 5 ACTIVE EP (IN SUBMERGED CONDITION)
MEMBER LOAD
25 TRAP GX 31.71 30.46
26 TRAP GX 30.46 28.95
27 TRAP GX 28.95 22.79
28 TRAP GX 22.79 16.63
29 TRAP GX 16.63 10.47
30 TRAP GX 10.47 4.3
31 TRAP GX 4.3 2.8
32 TRAP GX 2.8 1.54
56 TRAP GX -30.46 -31.71
55 TRAP GX -28.95 -30.46
54 TRAP GX -22.79 -28.95
53 TRAP GX -16.63 -22.79
52 TRAP GX -10.47 -16.63
51 TRAP GX -4.3 -10.47
50 TRAP GX -2.8 -4.3
49 TRAP GX -1.54 -2.8
LOAD 8 LL ACTIVE SURCHARGE (BS)
MEMBER LOAD
25 TO 32 UNI GX 6.71
49 TO 56 UNI GX -6.71
LOAD 9 LL ACTIVE SURCHARGE (LEFT SIDE)
MEMBER LOAD
25 TO 32 UNI GX 6.71
LOAD 10 LL ACTIVE SURCHARGE (RIGHT SIDE)
MEMBER LOAD
49 TO 56 UNI GX -6.71
LOAD 11 LL REST SURCHARGE (BS)
MEMBER LOAD
25 TO 32 UNI GX 12
49 TO 56 UNI GX -12
LOAD 12 LL REST SURCHARGE (LEFT SIDE)
MEMBER LOAD
25 TO 32 UNI GX 12
LOAD 13 LL REST SURCHARGE (RIGHT SIDE)
MEMBER LOAD
49 TO 56 UNI GX -12
LOAD 14 BRAKING FORCES (LEFT SIDE)
JOINT LOAD
27 FX 15.57
LOAD 15 BRAKING FORCES (RIGHT SIDE)
JOINT LOAD
87 FX -15.57
*TEMPERATURE CASE
LOAD 17 UNIFORM TEMP. RISE
TEMPERATURE LOAD
1 TO 8 33 TO 48 TEMP 17.5
LOAD 18 UNIFORM TEMP. FALL
TEMPERATURE LOAD
1 TO 8 33 TO 48 TEMP -17.5
************* FOR POSITIVE TEMPERATURE GRADIENT *************
LOAD 19 TEMPERATURE RISE
JOINT LOAD
27 FX 80.35 MZ -5.72
87 FX -80.35 MZ 5.72
************* FOR NEGATIVE TEMPERATURE GRADIENT *************
LOAD 20 TEMPERATURE FALL
JOINT LOAD
27 FX 39.5 MZ -0.21
87 FX -39.5 MZ 0.21
LOAD COMBINATION 100
1 1.35 2 1.35 3 1.75 17 1.5 4 1.5
LOAD COMBINATION 101
1 1.35 2 1.35
LOAD COMBINATION 102
1 1.35 2 1.35
LOAD COMBINATION 103
1 1.35 2 1.35 3 1.75 9 1.2 4 1.5 14 1.5 17 1.5
LOAD COMBINATION 104
1 1.35 2 1.35
LOAD COMBINATION 105
1 1.35 2 1.35
LOAD COMBINATION 106
1 1.35 2 1.35 3 1.75 12 1.2 4 1.5 14 1.5 17 1.5
LOAD COMBINATION 107
1 1.35 2 1.35 3 1.75 4 1.5 15 1.5 17 1.5
LOAD COMBINATION 108
1 1.35 2 1.35 3 1.75 17 1.5 5 1.5
LOAD COMBINATION 109
1 1.35 2 1.35 3 1.75 17 1.5 5 1.5
LOAD COMBINATION 110
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 17 1.5
LOAD COMBINATION 111
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 17 1.5
LOAD COMBINATION 112
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 17 1.5
LOAD COMBINATION 113
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 17 1.5
LOAD COMBINATION 114
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 17 1.5
LOAD COMBINATION 115
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 17 1.5
LOAD COMBINATION 116
1 1.35 2 1.35 3 1.75 17 1.5 4 1.5
LOAD COMBINATION 117
1 1.35 2 1.35 3 1.75 17 1.5 4 1.5
LOAD COMBINATION 118
1 1.35 2 1.35 3 1.75 8 1.2 4 1.5 17 1.5
LOAD COMBINATION 119
1 1.35 2 1.35 3 1.75 9 1.2 4 1.5 14 1.5 17 1.5
LOAD COMBINATION 120
1 1.35 2 1.35 3 1.75 4 1.5 15 1.5 17 1.5
LOAD COMBINATION 121
1 1.35 2 1.35 3 1.75 11 1.2 4 1.5 17 1.5
LOAD COMBINATION 122
1 1.35 2 1.35 3 1.75 12 1.2 4 1.5 14 1.5 17 1.5
LOAD COMBINATION 123
1 1.35 2 1.35 3 1.75 4 1.5 15 1.5 17 1.5
LOAD COMBINATION 124
1 1.35 2 1.35 3 1.75 17 1.5 5 1.5
LOAD COMBINATION 125
1 1.35 2 1.35 3 1.75 17 1.5 5 1.5
LOAD COMBINATION 126
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 17 1.5
LOAD COMBINATION 127
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 17 1.5
LOAD COMBINATION 128
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 17 1.5
LOAD COMBINATION 129
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 17 1.5
LOAD COMBINATION 130
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 17 1.5
LOAD COMBINATION 131
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 17 1.5
LOAD COMBINATION 132
1 1.35 2 1.35 3 1.75 17 1.5 5 1.5
LOAD COMBINATION 133
1 1.35 2 1.35 3 1.75 17 1.5 5 1.5
LOAD COMBINATION 134
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 17 1.5
LOAD COMBINATION 135
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 17 1.5
LOAD COMBINATION 136
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 17 1.5
LOAD COMBINATION 137
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 17 1.5
LOAD COMBINATION 138
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 17 1.5
LOAD COMBINATION 139
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 17 1.5
LOAD COMBINATION 140
1 1.35 2 1.35 3 1.75 17 1.5
LOAD COMBINATION 141
1 1.35 5 1.5
LOAD COMBINATION 142
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 17 1.5
LOAD COMBINATION 143
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 17 1.5
LOAD COMBINATION 144
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 17 1.5
LOAD COMBINATION 145
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 17 1.5
LOAD COMBINATION 146
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 17 1.5
LOAD COMBINATION 147
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 17 1.5
LOAD COMBINATION 148
1 1.35 2 1.35 3 1.75 17 1.5 5 1.5
LOAD COMBINATION 149
1 1.35 2 1.35 3 1.75 17 1.5 5 1.5
LOAD COMBINATION 150
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 17 1.5
LOAD COMBINATION 151
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 17 1.5
LOAD COMBINATION 152
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 17 1.5
LOAD COMBINATION 153
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 17 1.5
LOAD COMBINATION 154
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 17 1.5
LOAD COMBINATION 155
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 17 1.5
LOAD COMBINATION 156
1 1.35 2 1.35 3 1.75 17 1.5 5 1.5
LOAD COMBINATION 157
1 1.35 2 1.35 3 1.75 17 1.5 5 1.5
LOAD COMBINATION 158
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 17 1.5
LOAD COMBINATION 159
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 17 1.5
LOAD COMBINATION 160
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 17 1.5
LOAD COMBINATION 161
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 17 1.5
LOAD COMBINATION 162
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 17 1.5
LOAD COMBINATION 163
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 17 1.5
LOAD COMBINATION 166
1 1.35 2 1.35 3 1.75 18 1.5 4 1.5
LOAD COMBINATION 167
1 1.35 2 1.35 3 1.75 18 1.5 4 1.5
LOAD COMBINATION 168
1 1.35 2 1.35 3 1.75 8 1.2 4 1.5 18 1.5
LOAD COMBINATION 169
1 1.35 2 1.35 3 1.75 9 1.2 4 1.5 14 1.5 18 1.5
LOAD COMBINATION 170
1 1.35 2 1.35 3 1.75 4 1.5 15 1.5 18 1.5
LOAD COMBINATION 171
1 1.35 2 1.35 3 1.75 11 1.2 4 1.5 18 1.5
LOAD COMBINATION 172
1 1.35 2 1.35 3 1.75 12 1.2 4 1.5 14 1.5 18 1.5
LOAD COMBINATION 173
1 1.35 2 1.35 3 1.75 4 1.5 15 1.5 18 1.5
LOAD COMBINATION 174
1 1.35 2 1.35 3 1.75 18 1.5 5 1.5
LOAD COMBINATION 175
1 1.35 2 1.35 3 1.75 18 1.5 5 1.5
LOAD COMBINATION 176
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 18 1.5
LOAD COMBINATION 177
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 18 1.5
LOAD COMBINATION 178
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 18 1.5
LOAD COMBINATION 179
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 18 1.5
LOAD COMBINATION 180
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 18 1.5
LOAD COMBINATION 181
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 18 1.5
LOAD COMBINATION 182
1 1.35 2 1.35 3 1.75 18 1.5 4 1.5
LOAD COMBINATION 183
1 1.35 2 1.35 3 1.75 18 1.5 4 1.5
LOAD COMBINATION 184
1 1.35 2 1.35 3 1.75 8 1.2 4 1.5 18 1.5
LOAD COMBINATION 185
1 1.35 2 1.35 3 1.75 9 1.2 4 1.5 14 1.5 18 1.5
LOAD COMBINATION 186
1 1.35 2 1.35 3 1.75 4 1.5 15 1.5 18 1.5
LOAD COMBINATION 187
1 1.35 2 1.35 3 1.75 11 1.2 4 1.5 18 1.5
LOAD COMBINATION 188
1 1.35 2 1.35 3 1.75 12 1.2 4 1.5 14 1.5 18 1.5
LOAD COMBINATION 189
1 1.35 2 1.35 3 1.75 4 1.5 15 1.5 18 1.5
LOAD COMBINATION 190
1 1.35 2 1.35 3 1.75 18 1.5 5 1.5
LOAD COMBINATION 191
1 1.35 2 1.35 3 1.75 18 1.5 5 1.5
LOAD COMBINATION 192
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 18 1.5
LOAD COMBINATION 193
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 18 1.5
LOAD COMBINATION 194
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 18 1.5
LOAD COMBINATION 195
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 18 1.5
LOAD COMBINATION 196
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 18 1.5
LOAD COMBINATION 197
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 18 1.5
LOAD COMBINATION 198
1 1.35 2 1.35 3 1.75 18 1.5 5 1.5
LOAD COMBINATION 199
1 1.35 2 1.35 3 1.75 18 1.5 5 1.5
LOAD COMBINATION 200
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 18 1.5
LOAD COMBINATION 201
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 18 1.5
LOAD COMBINATION 202
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 18 1.5
LOAD COMBINATION 203
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 18 1.5
LOAD COMBINATION 204
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 18 1.5
LOAD COMBINATION 205
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 18 1.5
LOAD COMBINATION 206
1 1.35 2 1.35 3 1.75 18 1.5
LOAD COMBINATION 207
1 1.35 5 1.5
LOAD COMBINATION 208
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 18 1.5
LOAD COMBINATION 209
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 18 1.5
LOAD COMBINATION 210
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 18 1.5
LOAD COMBINATION 211
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 18 1.5
LOAD COMBINATION 212
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 18 1.5
LOAD COMBINATION 213
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 18 1.5
LOAD COMBINATION 214
1 1.35 2 1.35 3 1.75 18 1.5 5 1.5
LOAD COMBINATION 215
1 1.35 2 1.35 3 1.75 18 1.5 5 1.5
LOAD COMBINATION 216
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 18 1.5
LOAD COMBINATION 217
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 18 1.5
LOAD COMBINATION 218
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 18 1.5
LOAD COMBINATION 219
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 18 1.5
LOAD COMBINATION 220
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 18 1.5
LOAD COMBINATION 221
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 18 1.5
LOAD COMBINATION 222
1 1.35 2 1.35 3 1.75 18 1.5 5 1.5
LOAD COMBINATION 223
1 1.35 2 1.35 3 1.75 18 1.5 5 1.5
LOAD COMBINATION 224
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 18 1.5
LOAD COMBINATION 225
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 18 1.5
LOAD COMBINATION 226
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 18 1.5
LOAD COMBINATION 227
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 18 1.5
LOAD COMBINATION 228
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 18 1.5
LOAD COMBINATION 229
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 18 1.5
LOAD COMBINATION 232
1 1.35 2 1.35 3 1.75 19 1.5 4 1.5
LOAD COMBINATION 233
1 1.35 2 1.35 3 1.75 19 1.5 4 1.5
LOAD COMBINATION 234
1 1.35 2 1.35 3 1.75 8 1.2 4 1.5 19 1.5
LOAD COMBINATION 235
1 1.35 2 1.35 3 1.75 9 1.2 4 1.5 14 1.5 19 1.5
LOAD COMBINATION 236
1 1.35 2 1.35 3 1.75 4 1.5 15 1.5 19 1.5
LOAD COMBINATION 237
1 1.35 2 1.35 3 1.75 11 1.2 4 1.5 19 1.5
LOAD COMBINATION 238
1 1.35 2 1.35 3 1.75 12 1.2 4 1.5 14 1.5 19 1.5
LOAD COMBINATION 239
1 1.35 2 1.35 3 1.75 4 1.5 15 1.5 19 1.5
LOAD COMBINATION 240
1 1.35 2 1.35 3 1.75 19 1.5 5 1.5
LOAD COMBINATION 241
1 1.35 2 1.35 3 1.75 19 1.5 5 1.5
LOAD COMBINATION 242
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 19 1.5
LOAD COMBINATION 243
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 19 1.5
LOAD COMBINATION 244
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 19 1.5
LOAD COMBINATION 245
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 19 1.5
LOAD COMBINATION 246
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 19 1.5
LOAD COMBINATION 247
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 19 1.5
LOAD COMBINATION 248
1 1.35 2 1.35 3 1.75 19 1.5 4 1.5
LOAD COMBINATION 249
1 1.35 2 1.35 3 1.75 19 1.5 4 1.5
LOAD COMBINATION 250
1 1.35 2 1.35 3 1.75 8 1.2 4 1.5 19 1.5
LOAD COMBINATION 251
1 1.35 2 1.35 3 1.75 9 1.2 4 1.5 14 1.5 19 1.5
LOAD COMBINATION 252
1 1.35 2 1.35 3 1.75 4 1.5 15 1.5 19 1.5
LOAD COMBINATION 253
1 1.35 2 1.35 3 1.75 11 1.2 4 1.5 19 1.5
LOAD COMBINATION 254
1 1.35 2 1.35 3 1.75 12 1.2 4 1.5 14 1.5 19 1.5
LOAD COMBINATION 255
1 1.35 2 1.35 3 1.75 4 1.5 15 1.5 19 1.5
LOAD COMBINATION 256
1 1.35 2 1.35 3 1.75 19 1.5 5 1.5
LOAD COMBINATION 257
1 1.35 2 1.35 3 1.75 19 1.5 5 1.5
LOAD COMBINATION 258
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 19 1.5
LOAD COMBINATION 259
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 19 1.5
LOAD COMBINATION 260
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 19 1.5
LOAD COMBINATION 261
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 19 1.5
LOAD COMBINATION 262
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 19 1.5
LOAD COMBINATION 263
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 19 1.5
LOAD COMBINATION 264
1 1.35 2 1.35 3 1.75 19 1.5 5 1.5
LOAD COMBINATION 265
1 1.35 2 1.35 3 1.75 19 1.5 5 1.5
LOAD COMBINATION 266
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 19 1.5
LOAD COMBINATION 267
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 19 1.5
LOAD COMBINATION 268
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 19 1.5
LOAD COMBINATION 269
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 19 1.5
LOAD COMBINATION 270
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 19 1.5
LOAD COMBINATION 271
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 19 1.5
LOAD COMBINATION 272
1 1.35 2 1.35 3 1.75 19 1.5
LOAD COMBINATION 273
1 1.35 5 1.5
LOAD COMBINATION 274
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 19 1.5
LOAD COMBINATION 275
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 19 1.5
LOAD COMBINATION 276
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 19 1.5
LOAD COMBINATION 277
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 19 1.5
LOAD COMBINATION 278
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 19 1.5
LOAD COMBINATION 279
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 19 1.5
LOAD COMBINATION 280
1 1.35 2 1.35 3 1.75 19 1.5 5 1.5
LOAD COMBINATION 281
1 1.35 2 1.35 3 1.75 19 1.5 5 1.5
LOAD COMBINATION 282
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 19 1.5
LOAD COMBINATION 283
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 19 1.5
LOAD COMBINATION 284
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 19 1.5
LOAD COMBINATION 285
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 19 1.5
LOAD COMBINATION 286
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 19 1.5
LOAD COMBINATION 287
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 19 1.5
LOAD COMBINATION 288
1 1.35 2 1.35 3 1.75 19 1.5 5 1.5
LOAD COMBINATION 289
1 1.35 2 1.35 3 1.75 19 1.5 5 1.5
LOAD COMBINATION 290
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 19 1.5
LOAD COMBINATION 291
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 19 1.5
LOAD COMBINATION 292
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 19 1.5
LOAD COMBINATION 293
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 19 1.5
LOAD COMBINATION 294
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 19 1.5
LOAD COMBINATION 295
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 19 1.5
LOAD COMBINATION 298
1 1.35 2 1.35 3 1.75 20 1.5 4 1.5
LOAD COMBINATION 299
1 1.35 2 1.35 3 1.75 20 1.5 4 1.5
LOAD COMBINATION 300
1 1.35 2 1.35 3 1.75 8 1.2 4 1.5 20 1.5
LOAD COMBINATION 301
1 1.35 2 1.35 3 1.75 9 1.2 4 1.5 14 1.5 20 1.5
LOAD COMBINATION 302
1 1.35 2 1.35 3 1.75 4 1.5 15 1.5 20 1.5
LOAD COMBINATION 303
1 1.35 2 1.35 3 1.75 11 1.2 4 1.5 20 1.5
LOAD COMBINATION 304
1 1.35 2 1.35 3 1.75 12 1.2 4 1.5 14 1.5 20 1.5
LOAD COMBINATION 305
1 1.35 2 1.35 3 1.75 4 1.5 15 1.5 20 1.5
LOAD COMBINATION 306
1 1.35 2 1.35 3 1.75 20 1.5 5 1.5
LOAD COMBINATION 307
1 1.35 2 1.35 3 1.75 20 1.5 5 1.5
LOAD COMBINATION 308
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 20 1.5
LOAD COMBINATION 309
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 20 1.5
LOAD COMBINATION 310
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 20 1.5
LOAD COMBINATION 311
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 20 1.5
LOAD COMBINATION 312
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 20 1.5
LOAD COMBINATION 313
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 20 1.5
LOAD COMBINATION 314
1 1.35 2 1.35 3 1.75 20 1.5 4 1.5
LOAD COMBINATION 315
1 1.35 2 1.35 3 1.75 20 1.5 4 1.5
LOAD COMBINATION 316
1 1.35 2 1.35 3 1.75 8 1.2 4 1.5 20 1.5
LOAD COMBINATION 317
1 1.35 2 1.35 3 1.75 9 1.2 4 1.5 14 1.5 20 1.5
LOAD COMBINATION 318
1 1.35 2 1.35 3 1.75 4 1.5 15 1.5 20 1.5
LOAD COMBINATION 319
1 1.35 2 1.35 3 1.75 11 1.2 4 1.5 20 1.5
LOAD COMBINATION 320
1 1.35 2 1.35 3 1.75 12 1.2 4 1.5 14 1.5 20 1.5
LOAD COMBINATION 321
1 1.35 2 1.35 3 1.75 4 1.5 15 1.5 20 1.5
LOAD COMBINATION 322
1 1.35 2 1.35 3 1.75 20 1.5 5 1.5
LOAD COMBINATION 323
1 1.35 2 1.35 3 1.75 20 1.5 5 1.5
LOAD COMBINATION 324
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 20 1.5
LOAD COMBINATION 325
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 20 1.5
LOAD COMBINATION 326
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 20 1.5
LOAD COMBINATION 327
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 20 1.5
LOAD COMBINATION 328
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 20 1.5
LOAD COMBINATION 329
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 20 1.5
LOAD COMBINATION 330
1 1.35 2 1.35 3 1.75 20 1.5 5 1.5
LOAD COMBINATION 331
1 1.35 2 1.35 3 1.75 20 1.5 5 1.5
LOAD COMBINATION 332
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 20 1.5
LOAD COMBINATION 333
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 20 1.5
LOAD COMBINATION 334
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 20 1.5
LOAD COMBINATION 335
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 20 1.5
LOAD COMBINATION 336
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 20 1.5
LOAD COMBINATION 337
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 20 1.5
LOAD COMBINATION 338
1 1.35 2 1.35 3 1.75 20 1.5
LOAD COMBINATION 339
1 1.35 5 1.5
LOAD COMBINATION 340
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 20 1.5
LOAD COMBINATION 341
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 20 1.5
LOAD COMBINATION 342
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 20 1.5
LOAD COMBINATION 343
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 20 1.5
LOAD COMBINATION 344
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 20 1.5
LOAD COMBINATION 345
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 20 1.5
LOAD COMBINATION 346
1 1.35 2 1.35 3 1.75 20 1.5 5 1.5
LOAD COMBINATION 347
1 1.35 2 1.35 3 1.75 20 1.5 5 1.5
LOAD COMBINATION 348
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 20 1.5
LOAD COMBINATION 349
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 20 1.5
LOAD COMBINATION 350
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 20 1.5
LOAD COMBINATION 351
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 20 1.5
LOAD COMBINATION 352
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 20 1.5
LOAD COMBINATION 353
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 20 1.5
LOAD COMBINATION 354
1 1.35 2 1.35 3 1.75 20 1.5 5 1.5
LOAD COMBINATION 355
1 1.35 2 1.35 3 1.75 20 1.5 5 1.5
LOAD COMBINATION 356
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 20 1.5
LOAD COMBINATION 357
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 20 1.5
LOAD COMBINATION 358
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 20 1.5
LOAD COMBINATION 359
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 20 1.5
LOAD COMBINATION 360
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 20 1.5
LOAD COMBINATION 361
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 20 1.5
PERFORM ANALYSIS
FINISH
Staad SLS TL

STAAD PLANE
START JOB INFORMATION
ENGINEER DATE 20-08-2021
END JOB INFORMATION
INPUT WIDTH 79
UNIT METER KN
JOINT COORDINATES
1 0 0 0; 2 0.25 0 0; 3 1.15 0 0; 4 3.2 0 0; 5 5.25 0 0; 6 7.3 0 0; 7 9.35 0 0;
8 10.25 0 0; 9 10.5 0 0; 11 0.25 6 0; 12 1.15 6 0; 13 3.2 6 0; 14 5.25 6 0;
15 7.3 6 0; 16 9.35 6 0; 17 10.25 6 0; 18 10.5 6 0; 20 0 0.25 0; 21 0 0.55 0;
22 0 1.775 0; 23 0 3 0; 24 0 4.225 0; 25 0 5.45 0; 26 0 5.75 0; 27 0 6 0;
28 10.5 0.25 0; 29 10.5 0.55 0; 30 10.5 1.775 0; 31 10.5 3 0; 32 10.5 4.225 0;
33 10.5 5.45 0; 34 10.5 5.75 0; 36 10.75 0 0; 37 11.65 0 0; 38 13.7 0 0;
39 15.75 0 0; 40 17.8 0 0; 41 19.85 0 0; 42 20.75 0 0; 43 21 0 0; 45 10.75 6 0;
46 11.65 6 0; 47 13.7 6 0; 48 15.75 6 0; 49 17.8 6 0; 50 19.85 6 0;
51 20.75 6 0; 52 21 6 0; 54 21 0.25 0; 55 21 0.55 0; 56 21 1.775 0; 57 21 3 0;
58 21 4.225 0; 59 21 5.45 0; 60 21 5.75 0; 62 21.25 0 0; 63 22.15 0 0;
64 24.2 0 0; 65 26.25 0 0; 66 28.3 0 0; 67 30.35 0 0; 68 31.25 0 0;
69 31.5 0 0; 80 31.5 0.25 0; 81 31.5 0.55 0; 82 31.5 1.775 0; 83 31.5 3 0;
84 31.5 4.225 0; 85 31.5 5.45 0; 86 31.5 5.75 0; 87 31.5 6 0; 88 21.25 6 0;
89 22.15 6 0; 90 24.2 6 0; 91 26.25 6 0; 92 28.3 6 0; 93 30.35 6 0;
94 31.25 6 0;
MEMBER INCIDENCES
1 27 11; 2 11 12; 3 12 13; 4 13 14; 5 14 15; 6 15 16; 7 16 17; 8 17 18;
9 18 34; 10 34 33; 11 33 32; 12 32 31; 13 31 30; 14 30 29; 15 29 28; 16 28 9;
17 9 8; 18 8 7; 19 7 6; 20 6 5; 21 5 4; 22 4 3; 23 3 2; 24 2 1; 25 1 20;
26 20 21; 27 21 22; 28 22 23; 29 23 24; 30 24 25; 31 25 26; 32 26 27; 33 18 45;
34 45 46; 35 46 47; 36 47 48; 37 48 49; 38 49 50; 39 50 51; 40 51 52; 41 52 88;
42 88 89; 43 89 90; 44 90 91; 45 91 92; 46 92 93; 47 93 94; 48 94 87; 49 87 86;
50 86 85; 51 85 84; 52 84 83; 53 83 82; 54 82 81; 55 81 80; 56 80 69; 57 69 68;
58 68 67; 59 67 66; 60 66 65; 61 65 64; 62 64 63; 63 63 62; 64 62 43; 65 43 42;
66 42 41; 67 41 40; 68 40 39; 69 39 38; 70 38 37; 71 37 36; 72 36 9; 73 43 54;
74 54 55; 75 55 56; 76 56 57; 77 57 58; 78 58 59; 79 59 60; 80 60 52;
MEMBER PROPERTY INDIAN
1 8 33 40 41 48 PRIS YD 0.8 ZD 1
2 7 34 39 42 47 PRIS YD 0.65 ZD 1
3 TO 6 35 TO 38 43 TO 46 PRIS YD 0.5 ZD 1
11 TO 14 75 TO 78 PRIS YD 0.4 ZD 1
10 31 50 79 PRIS YD 0.95 ZD 1
27 TO 30 51 TO 54 PRIS YD 0.5 ZD 1
17 24 57 64 65 72 PRIS YD 0.8 ZD 1
18 23 58 63 66 71 PRIS YD 0.65 ZD 1
19 TO 22 59 TO 62 67 TO 70 PRIS YD 0.5 ZD 1
15 26 55 74 PRIS YD 0.95 ZD 1
9 16 25 32 49 56 73 80 PRIS YD 1.4 ZD 1
DEFINE MATERIAL START
ISOTROPIC CONCRETE
E 2.21467e+006
POISSON 0.17
DENSITY 2.40262
ALPHA 1e-005
DAMP 0.05
G 946439
TYPE CONCRETE
STRENGTH FCU 2812.28
END DEFINE MATERIAL
CONSTANTS
MATERIAL CONCRETE ALL
SUPPORTS
1 FIXED BUT FZ MX MY MZ KFY 416.667
9 FIXED BUT FX FZ MX MY MZ KFY 416.667
2 8 36 42 62 68 FIXED BUT FX FZ MX MY MZ KFY 1916.67
3 7 FIXED BUT FX FZ MX MY MZ KFY 4916.67
4 TO 6 FIXED BUT FX FZ MX MY MZ KFY 6833.33
1 FIXED BUT FZ MX MY MZ KFY 416.667
43 FIXED BUT FX FZ MX MY MZ KFY 416.667
37 41 FIXED BUT FX FZ MX MY MZ KFY 4916.67
38 TO 40 FIXED BUT FX FZ MX MY MZ KFY 6833.33
1 FIXED BUT FZ MX MY MZ KFY 416.667
69 FIXED BUT FX FZ MX MY MZ KFY 416.667
2 8 FIXED BUT FX FZ MX MY MZ KFY 1916.67
63 67 FIXED BUT FX FZ MX MY MZ KFY 4916.67
64 TO 66 FIXED BUT FX FZ MX MY MZ KFY 6833.33
LOAD 1 SELFWEIGHT
SELFWEIGHT Y -1
LOAD 2 SIDL
MEMBER LOAD
1 TO 8 33 TO 48 UNI GY -10
LOAD 3 SIDL (WC + EARTH FILL )
MEMBER LOAD
1 TO 8 33 TO 48 UNI GY -1.23
LOAD 4 REST EP (IN DRY CONDITION)
MEMBER LOAD
25 TRAP GX 65.56 63.06
26 TRAP GX 63.06 60.56
27 TRAP GX 60.56 45.31
28 TRAP GX 45.31 33.06
29 TRAP GX 33.06 20.81
30 TRAP GX 20.81 8.56
31 TRAP GX 8.56 5.56
32 TRAP GX 5.56 3.06
56 TRAP GX -63.06 -65.56
55 TRAP GX -60.56 -63.06
54 TRAP GX -45.31 -60.56
53 TRAP GX -33.06 -45.31
52 TRAP GX -20.81 -33.06
51 TRAP GX -8.56 -20.81
50 TRAP GX -5.56 -8.56
49 TRAP GX -3.06 -5.56
LOAD 5 ACTIVE EP (IN SUBMERGED CONDITION)
MEMBER LOAD
25 TRAP GX 31.71 30.46
26 TRAP GX 30.46 28.95
27 TRAP GX 28.95 22.79
28 TRAP GX 22.79 16.63
29 TRAP GX 16.63 10.47
30 TRAP GX 10.47 4.3
31 TRAP GX 4.3 2.8
32 TRAP GX 2.8 1.54
56 TRAP GX -30.46 -31.71
55 TRAP GX -28.95 -30.46
54 TRAP GX -22.79 -28.95
53 TRAP GX -16.63 -22.79
52 TRAP GX -10.47 -16.63
51 TRAP GX -4.3 -10.47
50 TRAP GX -2.8 -4.3
49 TRAP GX -1.54 -2.8
LOAD 8 LL ACTIVE SURCHARGE (BS)
MEMBER LOAD
25 TO 32 UNI GX 6.71
49 TO 56 UNI GX -6.71
LOAD 9 LL ACTIVE SURCHARGE (LEFT SIDE)
MEMBER LOAD
25 TO 32 UNI GX 6.71
LOAD 10 LL ACTIVE SURCHARGE (RIGHT SIDE)
MEMBER LOAD
49 TO 56 UNI GX -6.71
LOAD 11 LL REST SURCHARGE (BS)
MEMBER LOAD
25 TO 32 UNI GX 12
49 TO 56 UNI GX -12
LOAD 12 LL REST SURCHARGE (LEFT SIDE)
MEMBER LOAD
25 TO 32 UNI GX 12
LOAD 13 LL REST SURCHARGE (RIGHT SIDE)
MEMBER LOAD
49 TO 56 UNI GX -12
LOAD 14 BRAKING FORCES (LEFT SIDE)
JOINT LOAD
27 FX 15.57
LOAD 15 BRAKING FORCES (RIGHT SIDE)
JOINT LOAD
87 FX -15.57
*TEMPERATURE CASE
LOAD 17 UNIFORM TEMP. RISE
TEMPERATURE LOAD
1 TO 8 33 TO 48 TEMP 17.5
LOAD 18 UNIFORM TEMP. FALL
TEMPERATURE LOAD
1 TO 8 33 TO 48 TEMP -17.5
************* FOR POSITIVE TEMPERATURE GRADIENT *************
LOAD 19 TEMPERATURE RISE
JOINT LOAD
27 FX 80.35 MZ -5.72
87 FX -80.35 MZ 5.72
************* FOR NEGATIVE TEMPERATURE GRADIENT *************
LOAD 20 TEMPERATURE FALL
JOINT LOAD
27 FX 39.5 MZ -0.21
87 FX -39.5 MZ 0.21
LOAD COMBINATION 500
1 1 2 1 3 1.2 17 1 4 1
LOAD COMBINATION 501
1 1 2 1 3 1.2 17 1 4 1
LOAD COMBINATION 502
1 1 2 1 3 1.2 8 0.8 4 1 17 1
LOAD COMBINATION 503
1 1 2 1 3 1.2 9 0.8 4 1 14 1 17 1
LOAD COMBINATION 504
1 1 2 1 3 1.2 4 1 15 1 17 1
LOAD COMBINATION 505
1 1 2 1 3 1.2 11 0.8 4 1 17 1
LOAD COMBINATION 506
1 1 2 1 3 1.2 12 0.8 4 1 14 1 17 1
LOAD COMBINATION 507
1 1 2 1 3 1.2 4 1 15 1 17 1
LOAD COMBINATION 508
1 1 2 1 3 1.2 17 1 5 1
LOAD COMBINATION 509
1 1 2 1 3 1.2 17 1 5 1
LOAD COMBINATION 510
1 1 2 1 3 1.2 8 0.8 5 1 17 1
LOAD COMBINATION 511
1 1 2 1 3 1.2 9 0.8 5 1 14 1 17 1
LOAD COMBINATION 512
1 1 2 1 3 1.2 5 1 15 1 17 1
LOAD COMBINATION 513
1 1 2 1 3 1.2 11 0.8 5 1 17 1
LOAD COMBINATION 514
1 1 2 1 3 1.2 12 0.8 5 1 14 1 17 1
LOAD COMBINATION 515
1 1 2 1 3 1.2 5 1 15 1 17 1
LOAD COMBINATION 516
1 1 2 1 3 1.2 17 1 4 1
LOAD COMBINATION 517
1 1 2 1 3 1.2 17 1 4 1
LOAD COMBINATION 518
1 1 2 1 3 1.2 8 0.8 4 1 17 1
LOAD COMBINATION 519
1 1 2 1 3 1.2 9 0.8 4 1 14 1 17 1
LOAD COMBINATION 520
1 1 2 1 3 1.2 4 1 15 1 17 1
LOAD COMBINATION 521
1 1 2 1 3 1.2 11 0.8 4 1 17 1
LOAD COMBINATION 522
1 1 2 1 3 1.2 12 0.8 4 1 14 1 17 1
LOAD COMBINATION 523
1 1 2 1 3 1.2 4 1 15 1 17 1
LOAD COMBINATION 524
1 1 2 1 3 1.2 17 1 5 1
LOAD COMBINATION 525
1 1 2 1 3 1.2 17 1 5 1
LOAD COMBINATION 526
1 1 2 1 3 1.2 8 0.8 5 1 17 1
LOAD COMBINATION 527
1 1 2 1 3 1.2 9 0.8 5 1 14 1 17 1
LOAD COMBINATION 528
1 1 2 1 3 1.2 5 1 15 1 17 1
LOAD COMBINATION 529
1 1 2 1 3 1.2 11 0.8 5 1 17 1
LOAD COMBINATION 530
1 1 2 1 3 1.2 12 0.8 5 1 14 1 17 1
LOAD COMBINATION 531
1 1 2 1 3 1.2 5 1 15 1 17 1
LOAD COMBINATION 532
1 1 2 1 3 1.2 17 1 5 1
LOAD COMBINATION 533
1 1 2 1 3 1.2 17 1 5 1
LOAD COMBINATION 534
1 1 2 1 3 1.2 8 0.8 5 1 17 1
LOAD COMBINATION 535
1 1 2 1 3 1.2 9 0.8 5 1 14 1 17 1
LOAD COMBINATION 536
1 1 2 1 3 1.2 5 1 15 1 17 1
LOAD COMBINATION 537
1 1 2 1 3 1.2 11 0.8 5 1 17 1
LOAD COMBINATION 538
1 1 2 1 3 1.2 12 0.8 5 1 14 1 17 1
LOAD COMBINATION 539
1 1 2 1 3 1.2 5 1 15 1 17 1
LOAD COMBINATION 540
1 1 2 1 3 1.2 17 1
LOAD COMBINATION 541
11 51
LOAD COMBINATION 542
1 1 2 1 3 1.2 8 0.8 5 1 17 1
LOAD COMBINATION 543
1 1 2 1 3 1.2 9 0.8 5 1 14 1 17 1
LOAD COMBINATION 544
1 1 2 1 3 1.2 5 1 15 1 17 1
LOAD COMBINATION 545
1 1 2 1 3 1.2 11 0.8 5 1 17 1
LOAD COMBINATION 546
1 1 2 1 3 1.2 12 0.8 5 1 14 1 17 1
LOAD COMBINATION 547
1 1 2 1 3 1.2 5 1 15 1 17 1
LOAD COMBINATION 548
1 1 2 1 3 1.2 17 1 5 1
LOAD COMBINATION 549
1 1 2 1 3 1.2 17 1 5 1
LOAD COMBINATION 550
1 1 2 1 3 1.2 8 0.8 5 1 17 1
LOAD COMBINATION 551
1 1 2 1 3 1.2 9 0.8 5 1 14 1 17 1
LOAD COMBINATION 552
1 1 2 1 3 1.2 5 1 15 1 17 1
LOAD COMBINATION 553
1 1 2 1 3 1.2 11 0.8 5 1 17 1
LOAD COMBINATION 554
1 1 2 1 0 3 1.2 12 0.8 5 1 14 1 17 1
LOAD COMBINATION 555
1 1 2 1 3 1.2 5 1 15 1 17 1
LOAD COMBINATION 556
1 1 2 1 3 1.2 17 1 5 1
LOAD COMBINATION 557
1 1 2 1 3 1.2 17 1 5 1
LOAD COMBINATION 558
1 1 2 1 3 1.2 8 0.8 5 1 17 1
LOAD COMBINATION 559
1 1 2 1 3 1.2 9 0.8 5 1 14 1 17 1
LOAD COMBINATION 560
1 1 2 1 3 1.2 5 1 15 1 17 1
LOAD COMBINATION 561
1 1 2 1 3 1.2 11 0.8 5 1 17 1
LOAD COMBINATION 562
1 1 2 1 3 1.2 12 0.8 5 1 14 1 17 1
LOAD COMBINATION 563
1 1 2 1 3 1.2 5 1 15 1 17 1

LOAD COMBINATION 566

1 1 2 1 3 1.2 18 1 4 1
LOAD COMBINATION 567
1 1 2 1 3 1.2 18 1 4 1
LOAD COMBINATION 568
1 1 2 1 3 1.2 8 0.8 4 1 18 1
LOAD COMBINATION 569
1 1 2 1 3 1.2 9 0.8 4 1 14 1 18 1
LOAD COMBINATION 570
1 1 2 1 3 1.2 4 1 15 1 18 1
LOAD COMBINATION 571
1 1 2 1 3 1.2 11 0.8 4 1 18 1
LOAD COMBINATION 572
1 1 2 1 3 1.2 12 0.8 4 1 14 1 18 1
LOAD COMBINATION 573
1 1 2 1 3 1.2 4 1 15 1 18 1
LOAD COMBINATION 574
1 1 2 1 3 1.2 18 1 5 1
LOAD COMBINATION 575
1 1 2 1 3 1.2 18 1 5 1
LOAD COMBINATION 576
1 1 2 1 3 1.2 8 0.8 5 1 18 1
LOAD COMBINATION 577
1 1 2 1 3 1.2 9 0.8 5 1 14 1 18 1
LOAD COMBINATION 578
1 1 2 1 3 1.2 5 1 15 1 18 1
LOAD COMBINATION 579
1 1 2 1 3 1.2 11 0.8 5 1 18 1
LOAD COMBINATION 580
1 1 2 1 3 1.2 12 0.8 5 1 14 1 18 1
LOAD COMBINATION 581
1 1 2 1 3 1.2 5 1 15 1 18 1
LOAD COMBINATION 582
1 1 2 1 3 1.2 18 1 4 1
LOAD COMBINATION 583
1 1 2 1 3 1.2 18 1 4 1
LOAD COMBINATION 584
1 1 2 1 3 1.2 8 0.8 4 1 18 1
LOAD COMBINATION 585
1 1 2 1 3 1.2 9 0.8 4 1 14 1 18 1
LOAD COMBINATION 586
1 1 2 1 3 1.2 4 1 15 1 18 1
LOAD COMBINATION 587
1 1 2 1 3 1.2 11 0.8 4 1 18 1
LOAD COMBINATION 588
1 1 2 1 3 1.2 12 0.8 4 1 14 1 18 1
LOAD COMBINATION 589
1 1 2 1 3 1.2 4 1 15 1 18 1
LOAD COMBINATION 590
1 1 2 1 3 1.2 18 1 5 1
LOAD COMBINATION 591
1 1 2 1 3 1.2 18 1 5 1
LOAD COMBINATION 592
1 1 2 1 3 1.2 8 0.8 5 1 18 1
LOAD COMBINATION 593
1 1 2 1 3 1.2 9 0.8 5 1 14 1 18 1
LOAD COMBINATION 594
1 1 2 1 3 1.2 5 1 15 1 18 1
LOAD COMBINATION 595
1 1 2 1 3 1.2 11 0.8 5 1 18 1
LOAD COMBINATION 596
1 1 2 1 3 1.2 12 0.8 5 1 14 1 18 1
LOAD COMBINATION 597
1 1 2 1 3 1.2 5 1 15 1 18 1
LOAD COMBINATION 598
1 1 2 1 3 1.2 18 1 5 1
LOAD COMBINATION 599
1 1 2 1 3 1.2 18 1 5 1
LOAD COMBINATION 600
1 1 2 1 3 1.2 8 0.8 5 1 18 1
LOAD COMBINATION 601
1 1 2 1 3 1.2 9 0.8 5 1 14 1 18 1
LOAD COMBINATION 602
1 1 2 1 3 1.2 5 1 15 1 18 1
LOAD COMBINATION 603
1 1 2 1 3 1.2 11 0.8 5 1 18 1
LOAD COMBINATION 604
1 1 2 1 3 1.2 12 0.8 5 1 14 1 18 1
LOAD COMBINATION 605
1 1 2 1 3 1.2 5 1 15 1 18 1
LOAD COMBINATION 606
1 1 2 1 3 1.2 18 1
LOAD COMBINATION 607
11 51
LOAD COMBINATION 608
1 1 2 1 3 1.2 8 0.8 5 1 18 1
LOAD COMBINATION 609
1 1 2 1 3 1.2 9 0.8 5 1 14 1 18 1
LOAD COMBINATION 610
1 1 2 1 3 1.2 5 1 15 1 18 1
LOAD COMBINATION 611
1 1 2 1 3 1.2 11 0.8 5 1 18 1
LOAD COMBINATION 612
1 1 2 1 3 1.2 12 0.8 5 1 14 1 18 1
LOAD COMBINATION 613
1 1 2 1 3 1.2 5 1 15 1 18 1
LOAD COMBINATION 614
1 1 2 1 3 1.2 18 1 5 1
LOAD COMBINATION 615
1 1 2 1 3 1.2 18 1 5 1
LOAD COMBINATION 616
1 1 2 1 3 1.2 8 0.8 5 1 18 1
LOAD COMBINATION 617
1 1 2 1 3 1.2 9 0.8 5 1 14 1 18 1
LOAD COMBINATION 618
1 1 2 1 3 1.2 5 1 15 1 18 1
LOAD COMBINATION 619
1 1 2 1 3 1.2 11 0.8 5 1 18 1
LOAD COMBINATION 620
1 1 2 1 3 1.2 12 0.8 5 1 14 1 18 1
LOAD COMBINATION 621
1 1 2 1 3 1.2 5 1 15 1 18 1
LOAD COMBINATION 622
1 1 2 1 3 1.2 18 1 5 1
LOAD COMBINATION 623
1 1 2 1 3 1.2 18 1 5 1
LOAD COMBINATION 624
1 1 2 1 3 1.2 8 0.8 5 1 18 1
LOAD COMBINATION 625
1 1 2 1 3 1.2 9 0.8 5 1 14 1 18 1
LOAD COMBINATION 626
1 1 2 1 3 1.2 5 1 15 1 18 1
LOAD COMBINATION 627
1 1 2 1 3 1.2 11 0.8 5 1 18 1
LOAD COMBINATION 628
1 1 2 1 3 1.2 12 0.8 5 1 14 1 18 1
LOAD COMBINATION 629
1 1 2 1 3 1.2 5 1 15 1 18 1
LOAD COMBINATION 632
1 1 2 1 3 1.2 19 1 4 1
LOAD COMBINATION 633
1 1 2 1 3 1.2 19 1 4 1
LOAD COMBINATION 634
1 1 2 1 3 1.2 8 0.8 4 1 19 1
LOAD COMBINATION 635
1 1 2 1 3 1.2 9 0.8 4 1 14 1 19 1
LOAD COMBINATION 636
1 1 2 1 3 1.2 4 1 15 1 19 1
LOAD COMBINATION 637
1 1 2 1 3 1.2 11 0.8 4 1 19 1
LOAD COMBINATION 638
1 1 2 1 3 1.2 12 0.8 4 1 14 1 19 1
LOAD COMBINATION 639
1 1 2 1 3 1.2 4 1 15 1 19 1
LOAD COMBINATION 640
1 1 2 1 3 1.2 19 1 5 1
LOAD COMBINATION 641
1 1 2 1 3 1.2 19 1 5 1
LOAD COMBINATION 642
1 1 2 1 3 1.2 8 0.8 5 1 19 1
LOAD COMBINATION 643
1 1 2 1 3 1.2 9 0.8 5 1 14 1 19 1
LOAD COMBINATION 644
1 1 2 1 3 1.2 5 1 15 1 19 1
LOAD COMBINATION 645
1 1 2 1 3 1.2 11 0.8 5 1 19 1
LOAD COMBINATION 646
1 1 2 1 3 1.2 12 0.8 5 1 14 1 19 1
LOAD COMBINATION 647
1 1 2 1 3 1.2 5 1 15 1 19 1
LOAD COMBINATION 648
1 1 2 1 3 1.2 19 1 4 1
LOAD COMBINATION 649
1 1 2 1 3 1.2 19 1 4 1
LOAD COMBINATION 650
1 1 2 1 3 1.2 8 0.8 4 1 19 1
LOAD COMBINATION 651
1 1 2 1 3 1.2 9 0.8 4 1 14 1 19 1
LOAD COMBINATION 652
1 1 2 1 3 1.2 4 1 15 1 19 1
LOAD COMBINATION 653
1 1 2 1 3 1.2 11 0.8 4 1 19 1
LOAD COMBINATION 654
1 1 2 1 3 1.2 12 0.8 4 1 14 1 19 1
LOAD COMBINATION 655
1 1 2 1 3 1.2 4 1 15 1 19 1
LOAD COMBINATION 656
1 1 2 1 3 1.2 19 1 5 1
LOAD COMBINATION 657
1 1 2 1 3 1.2 19 1 5 1
LOAD COMBINATION 658
1 1 2 1 3 1.2 8 0.8 5 1 19 1
LOAD COMBINATION 659
1 1 2 1 3 1.2 9 0.8 5 1 14 1 19 1
LOAD COMBINATION 660
1 1 2 1 3 1.2 5 1 15 1 19 1
LOAD COMBINATION 661
1 1 2 1 3 1.2 11 0.8 5 1 19 1
LOAD COMBINATION 662
1 1 2 1 3 1.2 12 0.8 5 1 14 1 19 1
LOAD COMBINATION 663
1 1 2 1 3 1.2 5 1 15 1 19 1
LOAD COMBINATION 664
1 1 2 1 3 1.2 19 1 5 1
LOAD COMBINATION 665
1 1 2 1 3 1.2 19 1 5 1
LOAD COMBINATION 666
1 1 2 1 3 1.2 8 0.8 5 1 19 1
LOAD COMBINATION 667
1 1 2 1 3 1.2 9 0.8 5 1 14 1 19 1
LOAD COMBINATION 668
1 1 2 1 3 1.2 5 1 15 1 19 1
LOAD COMBINATION 669
1 1 2 1 3 1.2 11 0.8 5 1 19 1
LOAD COMBINATION 670
1 1 2 1 3 1.2 12 0.8 5 1 14 1 19 1
LOAD COMBINATION 671
1 1 2 1 3 1.2 5 1 15 1 19 1
LOAD COMBINATION 672
1 1 2 1 3 1.2 19 1
LOAD COMBINATION 673
11 51
LOAD COMBINATION 674
1 1 2 1 3 1.2 8 0.8 5 1 19 1
LOAD COMBINATION 675
1 1 2 1 3 1.2 9 0.8 5 1 14 1 19 1
LOAD COMBINATION 676
1 1 2 1 3 1.2 5 1 15 1 19 1
LOAD COMBINATION 677
1 1 2 1 3 1.2 11 0.8 5 1 19 1
LOAD COMBINATION 678
1 1 2 1 3 1.2 12 0.8 5 1 14 1 19 1
LOAD COMBINATION 679
1 1 2 1 3 1.2 5 1 15 1 19 1
LOAD COMBINATION 680
1 1 2 1 3 1.2 19 1 5 1
LOAD COMBINATION 681
1 1 2 1 3 1.2 19 1 5 1
LOAD COMBINATION 682
1 1 2 1 3 1.2 8 0.8 5 1 19 1
LOAD COMBINATION 683
1 1 2 1 3 1.2 9 0.8 5 1 14 1 19 1
LOAD COMBINATION 684
1 1 2 1 3 1.2 5 1 15 1 19 1
LOAD COMBINATION 685
1 1 2 1 3 1.2 11 0.8 5 1 19 1
LOAD COMBINATION 686
1 1 2 1 3 1.2 12 0.8 5 1 14 1 19 1
LOAD COMBINATION 687
1 1 2 1 3 1.2 5 1 15 1 19 1
LOAD COMBINATION 688
1 1 2 1 3 1.2 19 1 5 1
LOAD COMBINATION 689
1 1 2 1 3 1.2 19 1 5 1
LOAD COMBINATION 690
1 1 2 1 3 1.2 8 0.8 5 1 19 1
LOAD COMBINATION 691
1 1 2 1 3 1.2 9 0.8 5 1 14 1 19 1
LOAD COMBINATION 692
1 1 2 1 3 1.2 5 1 15 1 19 1
LOAD COMBINATION 693
1 1 2 1 3 1.2 11 0.8 5 1 19 1
LOAD COMBINATION 694
1 1 2 1 3 1.2 12 0.8 5 1 14 1 19 1
LOAD COMBINATION 695
1 1 2 1 3 1.2 5 1 15 1 19 1

LOAD COMBINATION 698

1 1 2 1 3 1.2 20 1 4 1
LOAD COMBINATION 699
1 1 2 1 3 1.2 20 1 4 1
LOAD COMBINATION 700
1 1 2 1 3 1.2 8 0.8 4 1 20 1
LOAD COMBINATION 701
1 1 2 1 3 1.2 9 0.8 4 1 14 1 20 1
LOAD COMBINATION 702
1 1 2 1 3 1.2 4 1 15 1 20 1
LOAD COMBINATION 703
1 1 2 1 3 1.2 11 0.8 4 1 20 1
LOAD COMBINATION 704
1 1 2 1 3 1.2 12 0.8 4 1 14 1 20 1
LOAD COMBINATION 705
1 1 2 1 3 1.2 4 1 15 1 20 1
LOAD COMBINATION 706
1 1 2 1 3 1.2 20 1 5 1
LOAD COMBINATION 707
1 1 2 1 3 1.2 20 1 5 1
LOAD COMBINATION 708
1 1 2 1 3 1.2 8 0.8 5 1 20 1
LOAD COMBINATION 709
1 1 2 1 3 1.2 9 0.8 5 1 14 1 20 1
LOAD COMBINATION 710
1 1 2 1 3 1.2 5 1 15 1 20 1
LOAD COMBINATION 711
1 1 2 1 3 1.2 11 0.8 5 1 20 1
LOAD COMBINATION 712
1 1 2 1 3 1.2 12 0.8 5 1 14 1 20 1
LOAD COMBINATION 713
1 1 2 1 3 1.2 5 1 15 1 20 1
LOAD COMBINATION 714
1 1 2 1 3 1.2 20 1 4 1
LOAD COMBINATION 715
1 1 2 1 3 1.2 20 1 4 1
LOAD COMBINATION 716
1 1 2 1 3 1.2 8 0.8 4 1 20 1
LOAD COMBINATION 717
1 1 2 1 3 1.2 9 0.8 4 1 14 1 20 1
LOAD COMBINATION 718
1 1 2 1 3 1.2 4 1 15 1 20 1
LOAD COMBINATION 719
1 1 2 1 3 1.2 11 0.8 4 1 20 1
LOAD COMBINATION 720
1 1 2 1 3 1.2 12 0.8 4 1 14 1 20 1
LOAD COMBINATION 721
1 1 2 1 3 1.2 4 1 15 1 20 1
LOAD COMBINATION 722
1 1 2 1 3 1.2 20 1 5 1
LOAD COMBINATION 723
1 1 2 1 3 1.2 20 1 5 1
LOAD COMBINATION 724
1 1 2 1 3 1.2 8 0.8 5 1 20 1
LOAD COMBINATION 725
1 1 2 1 3 1.2 9 0.8 5 1 14 1 20 1
LOAD COMBINATION 726
1 1 2 1 3 1.2 5 1 15 1 20 1
LOAD COMBINATION 727
1 1 2 1 3 1.2 11 0.8 5 1 20 1
LOAD COMBINATION 728
1 1 2 1 3 1.2 12 0.8 5 1 14 1 20 1
LOAD COMBINATION 729
1 1 2 1 3 1.2 5 1 15 1 20 1
LOAD COMBINATION 730
1 1 2 1 3 1.2 20 1 5 1
LOAD COMBINATION 731
1 1 2 1 3 1.2 20 1 5 1
LOAD COMBINATION 732
1 1 2 1 3 1.2 8 0.8 5 1 20 1
LOAD COMBINATION 733
1 1 2 1 3 1.2 9 0.8 5 1 14 1 20 1
LOAD COMBINATION 734
1 1 2 1 3 1.2 5 1 15 1 20 1
LOAD COMBINATION 735
1 1 2 1 3 1.2 11 0.8 5 1 20 1
LOAD COMBINATION 736
1 1 2 1 3 1.2 12 0.8 5 1 14 1 20 1
LOAD COMBINATION 737
1 1 2 1 3 1.2 5 1 15 1 20 1
LOAD COMBINATION 738
1 1 2 1 3 1.2 20 1
LOAD COMBINATION 739
11 51
LOAD COMBINATION 740
1 1 2 1 3 1.2 8 0.8 5 1 20 1
LOAD COMBINATION 741
1 1 2 1 3 1.2 9 0.8 5 1 14 1 20 1
LOAD COMBINATION 742
1 1 2 1 3 1.2 5 1 15 1 20 1
LOAD COMBINATION 743
1 1 2 1 3 1.2 11 0.8 5 1 20 1
LOAD COMBINATION 744
1 1 2 1 3 1.2 12 0.8 5 1 14 1 20 1
LOAD COMBINATION 745
1 1 2 1 3 1.2 5 1 15 1 20 1
LOAD COMBINATION 746
1 1 2 1 3 1.2 20 1 5 1
LOAD COMBINATION 747
1 1 2 1 3 1.2 20 1 5 1
LOAD COMBINATION 748
1 1 2 1 3 1.2 8 0.8 5 1 20 1
LOAD COMBINATION 749
1 1 2 1 3 1.2 9 0.8 5 1 14 1 20 1
LOAD COMBINATION 750
1 1 2 1 3 1.2 5 1 15 1 20 1
LOAD COMBINATION 751
1 1 2 1 3 1.2 11 0.8 5 1 20 1
LOAD COMBINATION 752
1 1 2 1 3 1.2 12 0.8 5 1 14 1 20 1
LOAD COMBINATION 753
1 1 2 1 3 1.2 5 1 15 1 20 1
LOAD COMBINATION 754
1 1 2 1 3 1.2 20 1 5 1
LOAD COMBINATION 755
1 1 2 1 3 1.2 20 1 5 1
LOAD COMBINATION 756
1 1 2 1 3 1.2 8 0.8 5 1 20 1
LOAD COMBINATION 757
1 1 2 1 3 1.2 9 0.8 5 1 14 1 20 1
LOAD COMBINATION 758
1 1 2 1 3 1.2 5 1 15 1 20 1
LOAD COMBINATION 759
1 1 2 1 3 1.2 11 0.8 5 1 20 1
LOAD COMBINATION 760
1 1 2 1 3 1.2 12 0.8 5 1 14 1 20 1
LOAD COMBINATION 761
1 1 2 1 3 1.2 5 1 15 1 20 1

PERFORM ANALYSIS
FINISH
STAAD SLS Temp Acc

STAAD PLANE
START JOB INFORMATION
ENGINEER DATE 20-08-2021
END JOB INFORMATION
INPUT WIDTH 79
UNIT METER KN
JOINT COORDINATES
1 0 0 0; 2 0.25 0 0; 3 1.15 0 0; 4 3.2 0 0; 5 5.25 0 0; 6 7.3 0 0; 7 9.35 0 0;
8 10.25 0 0; 9 10.5 0 0; 11 0.25 6 0; 12 1.15 6 0; 13 3.2 6 0; 14 5.25 6 0;
15 7.3 6 0; 16 9.35 6 0; 17 10.25 6 0; 18 10.5 6 0; 20 0 0.25 0; 21 0 0.55 0;
22 0 1.775 0; 23 0 3 0; 24 0 4.225 0; 25 0 5.45 0; 26 0 5.75 0; 27 0 6 0;
28 10.5 0.25 0; 29 10.5 0.55 0; 30 10.5 1.775 0; 31 10.5 3 0; 32 10.5 4.225 0;
33 10.5 5.45 0; 34 10.5 5.75 0; 36 10.75 0 0; 37 11.65 0 0; 38 13.7 0 0;
39 15.75 0 0; 40 17.8 0 0; 41 19.85 0 0; 42 20.75 0 0; 43 21 0 0; 45 10.75 6 0;
46 11.65 6 0; 47 13.7 6 0; 48 15.75 6 0; 49 17.8 6 0; 50 19.85 6 0;
51 20.75 6 0; 52 21 6 0; 54 21 0.25 0; 55 21 0.55 0; 56 21 1.775 0; 57 21 3 0;
58 21 4.225 0; 59 21 5.45 0; 60 21 5.75 0; 62 21.25 0 0; 63 22.15 0 0;
64 24.2 0 0; 65 26.25 0 0; 66 28.3 0 0; 67 30.35 0 0; 68 31.25 0 0;
69 31.5 0 0; 80 31.5 0.25 0; 81 31.5 0.55 0; 82 31.5 1.775 0; 83 31.5 3 0;
84 31.5 4.225 0; 85 31.5 5.45 0; 86 31.5 5.75 0; 87 31.5 6 0; 88 21.25 6 0;
89 22.15 6 0; 90 24.2 6 0; 91 26.25 6 0; 92 28.3 6 0; 93 30.35 6 0;
94 31.25 6 0;
MEMBER INCIDENCES
1 27 11; 2 11 12; 3 12 13; 4 13 14; 5 14 15; 6 15 16; 7 16 17; 8 17 18;
9 18 34; 10 34 33; 11 33 32; 12 32 31; 13 31 30; 14 30 29; 15 29 28; 16 28 9;
17 9 8; 18 8 7; 19 7 6; 20 6 5; 21 5 4; 22 4 3; 23 3 2; 24 2 1; 25 1 20;
26 20 21; 27 21 22; 28 22 23; 29 23 24; 30 24 25; 31 25 26; 32 26 27; 33 18 45;
34 45 46; 35 46 47; 36 47 48; 37 48 49; 38 49 50; 39 50 51; 40 51 52; 41 52 88;
42 88 89; 43 89 90; 44 90 91; 45 91 92; 46 92 93; 47 93 94; 48 94 87; 49 87 86;
50 86 85; 51 85 84; 52 84 83; 53 83 82; 54 82 81; 55 81 80; 56 80 69; 57 69 68;
58 68 67; 59 67 66; 60 66 65; 61 65 64; 62 64 63; 63 63 62; 64 62 43; 65 43 42;
66 42 41; 67 41 40; 68 40 39; 69 39 38; 70 38 37; 71 37 36; 72 36 9; 73 43 54;
74 54 55; 75 55 56; 76 56 57; 77 57 58; 78 58 59; 79 59 60; 80 60 52;
MEMBER PROPERTY INDIAN
1 8 33 40 41 48 PRIS YD 0.8 ZD 1
2 7 34 39 42 47 PRIS YD 0.65 ZD 1
3 TO 6 35 TO 38 43 TO 46 PRIS YD 0.5 ZD 1
11 TO 14 75 TO 78 PRIS YD 0.4 ZD 1
10 31 50 79 PRIS YD 0.95 ZD 1
27 TO 30 51 TO 54 PRIS YD 0.5 ZD 1
17 24 57 64 65 72 PRIS YD 0.8 ZD 1
18 23 58 63 66 71 PRIS YD 0.65 ZD 1
19 TO 22 59 TO 62 67 TO 70 PRIS YD 0.5 ZD 1
15 26 55 74 PRIS YD 0.95 ZD 1
9 16 25 32 49 56 73 80 PRIS YD 1.4 ZD 1
DEFINE MATERIAL START
ISOTROPIC CONCRETE
E 2.21467e+006
POISSON 0.17
DENSITY 2.40262
ALPHA 1e-005
DAMP 0.05
G 946439
TYPE CONCRETE
STRENGTH FCU 2812.28
END DEFINE MATERIAL
CONSTANTS
MATERIAL CONCRETE ALL
SUPPORTS
1 FIXED BUT FZ MX MY MZ KFY 416.667
9 FIXED BUT FX FZ MX MY MZ KFY 416.667
2 8 36 42 62 68 FIXED BUT FX FZ MX MY MZ KFY 1916.67
3 7 FIXED BUT FX FZ MX MY MZ KFY 4916.67
4 TO 6 FIXED BUT FX FZ MX MY MZ KFY 6833.33
1 FIXED BUT FZ MX MY MZ KFY 416.667
43 FIXED BUT FX FZ MX MY MZ KFY 416.667
37 41 FIXED BUT FX FZ MX MY MZ KFY 4916.67
38 TO 40 FIXED BUT FX FZ MX MY MZ KFY 6833.33
1 FIXED BUT FZ MX MY MZ KFY 416.667
69 FIXED BUT FX FZ MX MY MZ KFY 416.667
2 8 FIXED BUT FX FZ MX MY MZ KFY 1916.67
63 67 FIXED BUT FX FZ MX MY MZ KFY 4916.67
64 TO 66 FIXED BUT FX FZ MX MY MZ KFY 6833.33
LOAD 1 SELFWEIGHT
SELFWEIGHT Y -1
LOAD 2 SIDL
MEMBER LOAD
1 TO 8 33 TO 48 UNI GY -10
LOAD 3 SIDL (WC + EARTH FILL )
MEMBER LOAD
1 TO 8 33 TO 48 UNI GY -1.23
LOAD 4 REST EP (IN DRY CONDITION)
MEMBER LOAD
25 TRAP GX 65.56 63.06
26 TRAP GX 63.06 60.56
27 TRAP GX 60.56 45.31
28 TRAP GX 45.31 33.06
29 TRAP GX 33.06 20.81
30 TRAP GX 20.81 8.56
31 TRAP GX 8.56 5.56
32 TRAP GX 5.56 3.06
56 TRAP GX -63.06 -65.56
55 TRAP GX -60.56 -63.06
54 TRAP GX -45.31 -60.56
53 TRAP GX -33.06 -45.31
52 TRAP GX -20.81 -33.06
51 TRAP GX -8.56 -20.81
50 TRAP GX -5.56 -8.56
49 TRAP GX -3.06 -5.56
LOAD 5 ACTIVE EP (IN SUBMERGED CONDITION)
MEMBER LOAD
25 TRAP GX 31.71 30.46
26 TRAP GX 30.46 28.95
27 TRAP GX 28.95 22.79
28 TRAP GX 22.79 16.63
29 TRAP GX 16.63 10.47
30 TRAP GX 10.47 4.3
31 TRAP GX 4.3 2.8
32 TRAP GX 2.8 1.54
56 TRAP GX -30.46 -31.71
55 TRAP GX -28.95 -30.46
54 TRAP GX -22.79 -28.95
53 TRAP GX -16.63 -22.79
52 TRAP GX -10.47 -16.63
51 TRAP GX -4.3 -10.47
50 TRAP GX -2.8 -4.3
49 TRAP GX -1.54 -2.8
LOAD 8 LL ACTIVE SURCHARGE (BS)
MEMBER LOAD
25 TO 32 UNI GX 6.71
49 TO 56 UNI GX -6.71
LOAD 9 LL ACTIVE SURCHARGE (LEFT SIDE)
MEMBER LOAD
25 TO 32 UNI GX 6.71
LOAD 10 LL ACTIVE SURCHARGE (RIGHT SIDE)
MEMBER LOAD
49 TO 56 UNI GX -6.71
LOAD 11 LL REST SURCHARGE (BS)
MEMBER LOAD
25 TO 32 UNI GX 12
49 TO 56 UNI GX -12
LOAD 12 LL REST SURCHARGE (LEFT SIDE)
MEMBER LOAD
25 TO 32 UNI GX 12
LOAD 13 LL REST SURCHARGE (RIGHT SIDE)
MEMBER LOAD
49 TO 56 UNI GX -12
LOAD 14 BRAKING FORCES (LEFT SIDE)
JOINT LOAD
27 FX 15.57
LOAD 15 BRAKING FORCES (RIGHT SIDE)
JOINT LOAD
87 FX -15.57
*TEMPERATURE CASE
LOAD 17 UNIFORM TEMP. RISE
TEMPERATURE LOAD
1 TO 8 33 TO 48 TEMP 17.5
LOAD 18 UNIFORM TEMP. FALL
TEMPERATURE LOAD
1 TO 8 33 TO 48 TEMP -17.5
************* FOR POSITIVE TEMPERATURE GRADIENT *************
LOAD 19 TEMPERATURE RISE
JOINT LOAD
27 FX 80.35 MZ -5.72
87 FX -80.35 MZ 5.72
************* FOR NEGATIVE TEMPERATURE GRADIENT *************
LOAD 20 TEMPERATURE FALL
JOINT LOAD
27 FX 39.5 MZ -0.21
87 FX -39.5 MZ 0.21
LOAD COMBINATION 100
1 1.35 2 1.35 3 1.75 17 0.9 4 1.5
LOAD COMBINATION 101
1 1.35 2 1.35 3 1.75 17 0.9 4 1.5
LOAD COMBINATION 102
1 1.35 2 1.35 3 1.75 8 1.2 4 1.5 17 0.9
LOAD COMBINATION 103
1 1.35 2 1.35 3 1.75 9 1.2 4 1.5 14 1.5 17 0.9
LOAD COMBINATION 104
1 1.35 2 1.35 3 1.75 4 1.5 15 1.5 17 0.9
LOAD COMBINATION 105
1 1.35 2 1.35 3 1.75 11 1.2 4 1.5 17 0.9
LOAD COMBINATION 106
1 1.35 2 1.35 3 1.75 12 1.2 4 1.5 14 1.5 17 0.9
LOAD COMBINATION 107
1 1.35 2 1.35 3 1.75 4 1.5 15 1.5 17 0.9
LOAD COMBINATION 108
1 1.35 2 1.35 3 1.75 17 0.9 5 1.5
LOAD COMBINATION 109
1 1.35 2 1.35 3 1.75 17 0.9 5 1.5
LOAD COMBINATION 110
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 17 0.9
LOAD COMBINATION 111
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 17 0.9
LOAD COMBINATION 112
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 17 0.9
LOAD COMBINATION 113
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 17 0.9
LOAD COMBINATION 114
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 17 0.9
LOAD COMBINATION 115
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 17 0.9
LOAD COMBINATION 116
1 1.35 2 1.35 3 1.75 17 0.9 4 1.5
LOAD COMBINATION 117
1 1.35 2 1.35 3 1.75 17 0.9 4 1.5
LOAD COMBINATION 118
1 1.35 2 1.35 3 1.75 8 1.2 4 1.5 17 0.9
LOAD COMBINATION 119
1 1.35 2 1.35 3 1.75 9 1.2 4 1.5 14 1.5 17 0.9
LOAD COMBINATION 120
1 1.35 2 1.35 3 1.75 4 1.5 15 1.5 17 0.9
LOAD COMBINATION 121
1 1.35 2 1.35 3 1.75 11 1.2 4 1.5 17 0.9
LOAD COMBINATION 122
1 1.35 2 1.35 3 1.75 12 1.2 4 1.5 14 1.5 17 0.9
LOAD COMBINATION 123
1 1.35 2 1.35 3 1.75 4 1.5 15 1.5 17 0.9
LOAD COMBINATION 124
1 1.35 2 1.35 3 1.75 17 0.9 5 1.5
LOAD COMBINATION 125
1 1.35 2 1.35 3 1.75 17 0.9 5 1.5
LOAD COMBINATION 126
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 17 0.9
LOAD COMBINATION 127
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 17 0.9
LOAD COMBINATION 128
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 17 0.9
LOAD COMBINATION 129
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 17 0.9
LOAD COMBINATION 130
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 17 0.9
LOAD COMBINATION 131
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 17 0.9
LOAD COMBINATION 132
1 1.35 2 1.35 3 1.75 17 0.9 5 1.5
LOAD COMBINATION 133
1 1.35 2 1.35 3 1.75 17 0.9 5 1.5
LOAD COMBINATION 134
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 17 0.9
LOAD COMBINATION 135
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 17 0.9
LOAD COMBINATION 136
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 17 0.9
LOAD COMBINATION 137
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 17 0.9
LOAD COMBINATION 138
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 17 0.9
LOAD COMBINATION 139
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 17 0.9
LOAD COMBINATION 140
1 1.35 2 1.35 3 1.75 17 0.9
LOAD COMBINATION 141
1 1.35 5 1.5
LOAD COMBINATION 142
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 17 0.9
LOAD COMBINATION 143
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 17 0.9
LOAD COMBINATION 144
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 17 0.9
LOAD COMBINATION 145
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 17 0.9
LOAD COMBINATION 146
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 17 0.9
LOAD COMBINATION 147
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 17 0.9
LOAD COMBINATION 148
1 1.35 2 1.35 3 1.75 17 0.9 5 1.5
LOAD COMBINATION 149
1 1.35 2 1.35 3 1.75 17 0.9 5 1.5
LOAD COMBINATION 150
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 17 0.9
LOAD COMBINATION 151
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 17 0.9
LOAD COMBINATION 152
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 17 0.9
LOAD COMBINATION 153
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 17 0.9
LOAD COMBINATION 154
1 1.35 2 1.35 0 3 1.75 12 1.2 5 1.5 14 1.5 17 0.9
LOAD COMBINATION 155
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 17 0.9
LOAD COMBINATION 156
1 1.35 2 1.35 3 1.75 17 0.9 5 1.5
LOAD COMBINATION 157
1 1.35 2 1.35 3 1.75 17 0.9 5 1.5
LOAD COMBINATION 158
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 17 0.9
LOAD COMBINATION 159
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 17 0.9
LOAD COMBINATION 160
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 17 0.9
LOAD COMBINATION 161
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 17 0.9
LOAD COMBINATION 162
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 17 0.9
LOAD COMBINATION 163
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 17 0.9

LOAD COMBINATION 166

1 1.35 2 1.35 3 1.75 18 0.9 4 1.5
LOAD COMBINATION 167
1 1.35 2 1.35 3 1.75 18 0.9 4 1.5
LOAD COMBINATION 168
1 1.35 2 1.35 3 1.75 8 1.2 4 1.5 18 0.9
LOAD COMBINATION 169
1 1.35 2 1.35 3 1.75 9 1.2 4 1.5 14 1.5 18 0.9
LOAD COMBINATION 170
1 1.35 2 1.35 3 1.75 4 1.5 15 1.5 18 0.9
LOAD COMBINATION 171
1 1.35 2 1.35 3 1.75 11 1.2 4 1.5 18 0.9
LOAD COMBINATION 172
1 1.35 2 1.35 3 1.75 12 1.2 4 1.5 14 1.5 18 0.9
LOAD COMBINATION 173
1 1.35 2 1.35 3 1.75 4 1.5 15 1.5 18 0.9
LOAD COMBINATION 174
1 1.35 2 1.35 3 1.75 18 0.9 5 1.5
LOAD COMBINATION 175
1 1.35 2 1.35 3 1.75 18 0.9 5 1.5
LOAD COMBINATION 176
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 18 0.9
LOAD COMBINATION 177
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 18 0.9
LOAD COMBINATION 178
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 18 0.9
LOAD COMBINATION 179
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 18 0.9
LOAD COMBINATION 180
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 18 0.9
LOAD COMBINATION 181
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 18 0.9
LOAD COMBINATION 182
1 1.35 2 1.35 3 1.75 18 0.9 4 1.5
LOAD COMBINATION 183
1 1.35 2 1.35 3 1.75 18 0.9 4 1.5
LOAD COMBINATION 184
1 1.35 2 1.35 3 1.75 8 1.2 4 1.5 18 0.9
LOAD COMBINATION 185
1 1.35 2 1.35 3 1.75 9 1.2 4 1.5 14 1.5 18 0.9
LOAD COMBINATION 186
1 1.35 2 1.35 3 1.75 4 1.5 15 1.5 18 0.9
LOAD COMBINATION 187
1 1.35 2 1.35 3 1.75 11 1.2 4 1.5 18 0.9
LOAD COMBINATION 188
1 1.35 2 1.35 3 1.75 12 1.2 4 1.5 14 1.5 18 0.9
LOAD COMBINATION 189
1 1.35 2 1.35 3 1.75 4 1.5 15 1.5 18 0.9
LOAD COMBINATION 190
1 1.35 2 1.35 3 1.75 18 0.9 5 1.5
LOAD COMBINATION 191
1 1.35 2 1.35 3 1.75 18 0.9 5 1.5
LOAD COMBINATION 192
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 18 0.9
LOAD COMBINATION 193
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 18 0.9
LOAD COMBINATION 194
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 18 0.9
LOAD COMBINATION 195
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 18 0.9
LOAD COMBINATION 196
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 18 0.9
LOAD COMBINATION 197
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 18 0.9
LOAD COMBINATION 198
1 1.35 2 1.35 3 1.75 18 0.9 5 1.5
LOAD COMBINATION 199
1 1.35 2 1.35 3 1.75 18 0.9 5 1.5
LOAD COMBINATION 200
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 18 0.9
LOAD COMBINATION 201
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 18 0.9
LOAD COMBINATION 202
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 18 0.9
LOAD COMBINATION 203
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 18 0.9
LOAD COMBINATION 204
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 18 0.9
LOAD COMBINATION 205
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 18 0.9
LOAD COMBINATION 206
1 1.35 2 1.35 3 1.75 18 0.9
LOAD COMBINATION 207
1 1.35 5 1.5
LOAD COMBINATION 208
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 18 0.9
LOAD COMBINATION 209
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 18 0.9
LOAD COMBINATION 210
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 18 0.9
LOAD COMBINATION 211
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 18 0.9
LOAD COMBINATION 212
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 18 0.9
LOAD COMBINATION 213
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 18 0.9
LOAD COMBINATION 214
1 1.35 2 1.35 3 1.75 18 0.9 5 1.5
LOAD COMBINATION 215
1 1.35 2 1.35 3 1.75 18 0.9 5 1.5
LOAD COMBINATION 216
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 18 0.9
LOAD COMBINATION 217
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 18 0.9
LOAD COMBINATION 218
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 18 0.9
LOAD COMBINATION 219
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 18 0.9
LOAD COMBINATION 220
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 18 0.9
LOAD COMBINATION 221
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 18 0.9
LOAD COMBINATION 222
1 1.35 2 1.35 3 1.75 18 0.9 5 1.5
LOAD COMBINATION 223
1 1.35 2 1.35 3 1.75 18 0.9 5 1.5
LOAD COMBINATION 224
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 18 0.9
LOAD COMBINATION 225
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 18 0.9
LOAD COMBINATION 226
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 18 0.9
LOAD COMBINATION 227
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 18 0.9
LOAD COMBINATION 228
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 18 0.9
LOAD COMBINATION 229
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 18 0.9
LOAD COMBINATION 232
1 1.35 2 1.35 3 1.75 19 0.9 4 1.5
LOAD COMBINATION 233
1 1.35 2 1.35 3 1.75 19 0.9 4 1.5
LOAD COMBINATION 234
1 1.35 2 1.35 3 1.75 8 1.2 4 1.5 19 0.9
LOAD COMBINATION 235
1 1.35 2 1.35 3 1.75 9 1.2 4 1.5 14 1.5 19 0.9
LOAD COMBINATION 236
1 1.35 2 1.35 3 1.75 4 1.5 15 1.5 19 0.9
LOAD COMBINATION 237
1 1.35 2 1.35 3 1.75 11 1.2 4 1.5 19 0.9
LOAD COMBINATION 238
1 1.35 2 1.35 3 1.75 12 1.2 4 1.5 14 1.5 19 0.9
LOAD COMBINATION 239
1 1.35 2 1.35 3 1.75 4 1.5 15 1.5 19 0.9
LOAD COMBINATION 240
1 1.35 2 1.35 3 1.75 19 0.9 5 1.5
LOAD COMBINATION 241
1 1.35 2 1.35 3 1.75 19 0.9 5 1.5
LOAD COMBINATION 242
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 19 0.9
LOAD COMBINATION 243
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 19 0.9
LOAD COMBINATION 244
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 19 0.9
LOAD COMBINATION 245
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 19 0.9
LOAD COMBINATION 246
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 19 0.9
LOAD COMBINATION 247
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 19 0.9
LOAD COMBINATION 248
1 1.35 2 1.35 3 1.75 19 0.9 4 1.5
LOAD COMBINATION 249
1 1.35 2 1.35 3 1.75 19 0.9 4 1.5
LOAD COMBINATION 250
1 1.35 2 1.35 3 1.75 8 1.2 4 1.5 19 0.9
LOAD COMBINATION 251
1 1.35 2 1.35 3 1.75 9 1.2 4 1.5 14 1.5 19 0.9
LOAD COMBINATION 252
1 1.35 2 1.35 3 1.75 4 1.5 15 1.5 19 0.9
LOAD COMBINATION 253
1 1.35 2 1.35 3 1.75 11 1.2 4 1.5 19 0.9
LOAD COMBINATION 254
1 1.35 2 1.35 3 1.75 12 1.2 4 1.5 14 1.5 19 0.9
LOAD COMBINATION 255
1 1.35 2 1.35 3 1.75 4 1.5 15 1.5 19 0.9
LOAD COMBINATION 256
1 1.35 2 1.35 3 1.75 19 0.9 5 1.5
LOAD COMBINATION 257
1 1.35 2 1.35 3 1.75 19 0.9 5 1.5
LOAD COMBINATION 258
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 19 0.9
LOAD COMBINATION 259
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 19 0.9
LOAD COMBINATION 260
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 19 0.9
LOAD COMBINATION 261
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 19 0.9
LOAD COMBINATION 262
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 19 0.9
LOAD COMBINATION 263
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 19 0.9
LOAD COMBINATION 264
1 1.35 2 1.35 3 1.75 19 0.9 5 1.5
LOAD COMBINATION 265
1 1.35 2 1.35 3 1.75 19 0.9 5 1.5
LOAD COMBINATION 266
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 19 0.9
LOAD COMBINATION 267
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 19 0.9
LOAD COMBINATION 268
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 19 0.9
LOAD COMBINATION 269
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 19 0.9
LOAD COMBINATION 270
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 19 0.9
LOAD COMBINATION 271
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 19 0.9
LOAD COMBINATION 272
1 1.35 2 1.35 3 1.75 19 0.9
LOAD COMBINATION 273
1 1.35 5 1.5
LOAD COMBINATION 274
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 19 0.9
LOAD COMBINATION 275
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 19 0.9
LOAD COMBINATION 276
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 19 0.9
LOAD COMBINATION 277
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 19 0.9
LOAD COMBINATION 278
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 19 0.9
LOAD COMBINATION 279
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 19 0.9
LOAD COMBINATION 280
1 1.35 2 1.35 3 1.75 19 0.9 5 1.5
LOAD COMBINATION 281
1 1.35 2 1.35 3 1.75 19 0.9 5 1.5
LOAD COMBINATION 282
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 19 0.9
LOAD COMBINATION 283
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 19 0.9
LOAD COMBINATION 284
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 19 0.9
LOAD COMBINATION 285
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 19 0.9
LOAD COMBINATION 286
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 19 0.9
LOAD COMBINATION 287
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 19 0.9
LOAD COMBINATION 288
1 1.35 2 1.35 3 1.75 19 0.9 5 1.5
LOAD COMBINATION 289
1 1.35 2 1.35 3 1.75 19 0.9 5 1.5
LOAD COMBINATION 290
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 19 0.9
LOAD COMBINATION 291
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 19 0.9
LOAD COMBINATION 292
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 19 0.9
LOAD COMBINATION 293
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 19 0.9
LOAD COMBINATION 294
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 19 0.9
LOAD COMBINATION 295
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 19 0.9

LOAD COMBINATION 298

1 1.35 2 1.35 3 1.75 20 0.9 4 1.5
LOAD COMBINATION 299
1 1.35 2 1.35 3 1.75 20 0.9 4 1.5
LOAD COMBINATION 300
1 1.35 2 1.35 3 1.75 8 1.2 4 1.5 20 0.9
LOAD COMBINATION 301
1 1.35 2 1.35 3 1.75 9 1.2 4 1.5 14 1.5 20 0.9
LOAD COMBINATION 302
1 1.35 2 1.35 3 1.75 4 1.5 15 1.5 20 0.9
LOAD COMBINATION 303
1 1.35 2 1.35 3 1.75 11 1.2 4 1.5 20 0.9
LOAD COMBINATION 304
1 1.35 2 1.35 3 1.75 12 1.2 4 1.5 14 1.5 20 0.9
LOAD COMBINATION 305
1 1.35 2 1.35 3 1.75 4 1.5 15 1.5 20 0.9
LOAD COMBINATION 306
1 1.35 2 1.35 3 1.75 20 0.9 5 1.5
LOAD COMBINATION 307
1 1.35 2 1.35 3 1.75 20 0.9 5 1.5
LOAD COMBINATION 308
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 20 0.9
LOAD COMBINATION 309
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 20 0.9
LOAD COMBINATION 310
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 20 0.9
LOAD COMBINATION 311
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 20 0.9
LOAD COMBINATION 312
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 20 0.9
LOAD COMBINATION 313
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 20 0.9
LOAD COMBINATION 314
1 1.35 2 1.35 3 1.75 20 0.9 4 1.5
LOAD COMBINATION 315
1 1.35 2 1.35 3 1.75 20 0.9 4 1.5
LOAD COMBINATION 316
1 1.35 2 1.35 3 1.75 8 1.2 4 1.5 20 0.9
LOAD COMBINATION 317
1 1.35 2 1.35 3 1.75 9 1.2 4 1.5 14 1.5 20 0.9
LOAD COMBINATION 318
1 1.35 2 1.35 3 1.75 4 1.5 15 1.5 20 0.9
LOAD COMBINATION 319
1 1.35 2 1.35 3 1.75 11 1.2 4 1.5 20 0.9
LOAD COMBINATION 320
1 1.35 2 1.35 3 1.75 12 1.2 4 1.5 14 1.5 20 0.9
LOAD COMBINATION 321
1 1.35 2 1.35 3 1.75 4 1.5 15 1.5 20 0.9
LOAD COMBINATION 322
1 1.35 2 1.35 3 1.75 20 0.9 5 1.5
LOAD COMBINATION 323
1 1.35 2 1.35 3 1.75 20 0.9 5 1.5
LOAD COMBINATION 324
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 20 0.9
LOAD COMBINATION 325
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 20 0.9
LOAD COMBINATION 326
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 20 0.9
LOAD COMBINATION 327
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 20 0.9
LOAD COMBINATION 328
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 20 0.9
LOAD COMBINATION 329
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 20 0.9
LOAD COMBINATION 330
1 1.35 2 1.35 3 1.75 20 0.9 5 1.5
LOAD COMBINATION 331
1 1.35 2 1.35 3 1.75 20 0.9 5 1.5
LOAD COMBINATION 332
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 20 0.9
LOAD COMBINATION 333
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 20 0.9
LOAD COMBINATION 334
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 20 0.9
LOAD COMBINATION 335
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 20 0.9
LOAD COMBINATION 336
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 20 0.9
LOAD COMBINATION 337
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 20 0.9
LOAD COMBINATION 338
1 1.35 2 1.35 3 1.75 20 0.9
LOAD COMBINATION 339
1 1.35 5 1.5
LOAD COMBINATION 340
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 20 0.9
LOAD COMBINATION 341
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 20 0.9
LOAD COMBINATION 342
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 20 0.9
LOAD COMBINATION 343
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 20 0.9
LOAD COMBINATION 344
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 20 0.9
LOAD COMBINATION 345
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 20 0.9
LOAD COMBINATION 346
1 1.35 2 1.35 3 1.75 20 0.9 5 1.5
LOAD COMBINATION 347
1 1.35 2 1.35 3 1.75 20 0.9 5 1.5
LOAD COMBINATION 348
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 20 0.9
LOAD COMBINATION 349
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 20 0.9
LOAD COMBINATION 350
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 20 0.9
LOAD COMBINATION 351
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 20 0.9
LOAD COMBINATION 352
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 20 0.9
LOAD COMBINATION 353
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 20 0.9
LOAD COMBINATION 354
1 1.35 2 1.35 3 1.75 20 0.9 5 1.5
LOAD COMBINATION 355
1 1.35 2 1.35 3 1.75 20 0.9 5 1.5
LOAD COMBINATION 356
1 1.35 2 1.35 3 1.75 8 1.2 5 1.5 20 0.9
LOAD COMBINATION 357
1 1.35 2 1.35 3 1.75 9 1.2 5 1.5 14 1.5 20 0.9
LOAD COMBINATION 358
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 20 0.9
LOAD COMBINATION 359
1 1.35 2 1.35 3 1.75 11 1.2 5 1.5 20 0.9
LOAD COMBINATION 360
1 1.35 2 1.35 3 1.75 12 1.2 5 1.5 14 1.5 20 0.9
LOAD COMBINATION 361
1 1.35 2 1.35 3 1.75 5 1.5 15 1.5 20 0.9

PERFORM ANALYSIS
FINISH
Staad QLS Tem Acc

STAAD PLANE
START JOB INFORMATION
ENGINEER DATE 20-08-2021
END JOB INFORMATION
INPUT WIDTH 79
UNIT METER KN
JOINT COORDINATES
1 0 0 0; 2 0.25 0 0; 3 1.15 0 0; 4 3.2 0 0; 5 5.25 0 0; 6 7.3 0 0; 7 9.35 0 0;
8 10.25 0 0; 9 10.5 0 0; 11 0.25 6 0; 12 1.15 6 0; 13 3.2 6 0; 14 5.25 6 0;
15 7.3 6 0; 16 9.35 6 0; 17 10.25 6 0; 18 10.5 6 0; 20 0 0.25 0; 21 0 0.55 0;
22 0 1.775 0; 23 0 3 0; 24 0 4.225 0; 25 0 5.45 0; 26 0 5.75 0; 27 0 6 0;
28 10.5 0.25 0; 29 10.5 0.55 0; 30 10.5 1.775 0; 31 10.5 3 0; 32 10.5 4.225 0;
33 10.5 5.45 0; 34 10.5 5.75 0; 36 10.75 0 0; 37 11.65 0 0; 38 13.7 0 0;
39 15.75 0 0; 40 17.8 0 0; 41 19.85 0 0; 42 20.75 0 0; 43 21 0 0; 45 10.75 6 0;
46 11.65 6 0; 47 13.7 6 0; 48 15.75 6 0; 49 17.8 6 0; 50 19.85 6 0;
51 20.75 6 0; 52 21 6 0; 54 21 0.25 0; 55 21 0.55 0; 56 21 1.775 0; 57 21 3 0;
58 21 4.225 0; 59 21 5.45 0; 60 21 5.75 0; 62 21.25 0 0; 63 22.15 0 0;
64 24.2 0 0; 65 26.25 0 0; 66 28.3 0 0; 67 30.35 0 0; 68 31.25 0 0;
69 31.5 0 0; 80 31.5 0.25 0; 81 31.5 0.55 0; 82 31.5 1.775 0; 83 31.5 3 0;
84 31.5 4.225 0; 85 31.5 5.45 0; 86 31.5 5.75 0; 87 31.5 6 0; 88 21.25 6 0;
89 22.15 6 0; 90 24.2 6 0; 91 26.25 6 0; 92 28.3 6 0; 93 30.35 6 0;
94 31.25 6 0;
MEMBER INCIDENCES
1 27 11; 2 11 12; 3 12 13; 4 13 14; 5 14 15; 6 15 16; 7 16 17; 8 17 18;
9 18 34; 10 34 33; 11 33 32; 12 32 31; 13 31 30; 14 30 29; 15 29 28; 16 28 9;
17 9 8; 18 8 7; 19 7 6; 20 6 5; 21 5 4; 22 4 3; 23 3 2; 24 2 1; 25 1 20;
26 20 21; 27 21 22; 28 22 23; 29 23 24; 30 24 25; 31 25 26; 32 26 27; 33 18 45;
34 45 46; 35 46 47; 36 47 48; 37 48 49; 38 49 50; 39 50 51; 40 51 52; 41 52 88;
42 88 89; 43 89 90; 44 90 91; 45 91 92; 46 92 93; 47 93 94; 48 94 87; 49 87 86;
50 86 85; 51 85 84; 52 84 83; 53 83 82; 54 82 81; 55 81 80; 56 80 69; 57 69 68;
58 68 67; 59 67 66; 60 66 65; 61 65 64; 62 64 63; 63 63 62; 64 62 43; 65 43 42;
66 42 41; 67 41 40; 68 40 39; 69 39 38; 70 38 37; 71 37 36; 72 36 9; 73 43 54;
74 54 55; 75 55 56; 76 56 57; 77 57 58; 78 58 59; 79 59 60; 80 60 52;
MEMBER PROPERTY INDIAN
1 8 33 40 41 48 PRIS YD 0.8 ZD 1
2 7 34 39 42 47 PRIS YD 0.65 ZD 1
3 TO 6 35 TO 38 43 TO 46 PRIS YD 0.5 ZD 1
11 TO 14 75 TO 78 PRIS YD 0.4 ZD 1
10 31 50 79 PRIS YD 0.95 ZD 1
27 TO 30 51 TO 54 PRIS YD 0.5 ZD 1
17 24 57 64 65 72 PRIS YD 0.8 ZD 1
18 23 58 63 66 71 PRIS YD 0.65 ZD 1
19 TO 22 59 TO 62 67 TO 70 PRIS YD 0.5 ZD 1
15 26 55 74 PRIS YD 0.95 ZD 1
9 16 25 32 49 56 73 80 PRIS YD 1.4 ZD 1
DEFINE MATERIAL START
ISOTROPIC CONCRETE
E 2.21467e+006
POISSON 0.17
DENSITY 2.40262
ALPHA 1e-005
DAMP 0.05
G 946439
TYPE CONCRETE
STRENGTH FCU 2812.28
END DEFINE MATERIAL
CONSTANTS
MATERIAL CONCRETE ALL
SUPPORTS
1 FIXED BUT FZ MX MY MZ KFY 416.667
9 FIXED BUT FX FZ MX MY MZ KFY 416.667
2 8 36 42 62 68 FIXED BUT FX FZ MX MY MZ KFY 1916.67
3 7 FIXED BUT FX FZ MX MY MZ KFY 4916.67
4 TO 6 FIXED BUT FX FZ MX MY MZ KFY 6833.33
1 FIXED BUT FZ MX MY MZ KFY 416.667
43 FIXED BUT FX FZ MX MY MZ KFY 416.667
37 41 FIXED BUT FX FZ MX MY MZ KFY 4916.67
38 TO 40 FIXED BUT FX FZ MX MY MZ KFY 6833.33
1 FIXED BUT FZ MX MY MZ KFY 416.667
69 FIXED BUT FX FZ MX MY MZ KFY 416.667
2 8 FIXED BUT FX FZ MX MY MZ KFY 1916.67
63 67 FIXED BUT FX FZ MX MY MZ KFY 4916.67
64 TO 66 FIXED BUT FX FZ MX MY MZ KFY 6833.33
LOAD 1 SELFWEIGHT
SELFWEIGHT Y -1
LOAD 2 SIDL
MEMBER LOAD
1 TO 8 33 TO 48 UNI GY -10
LOAD 3 SIDL (WC + EARTH FILL )
MEMBER LOAD
1 TO 8 33 TO 48 UNI GY -1.23
LOAD 4 REST EP (IN DRY CONDITION)
MEMBER LOAD
25 TRAP GX 65.56 63.06
26 TRAP GX 63.06 60.56
27 TRAP GX 60.56 45.31
28 TRAP GX 45.31 33.06
29 TRAP GX 33.06 20.81
30 TRAP GX 20.81 8.56
31 TRAP GX 8.56 5.56
32 TRAP GX 5.56 3.06
56 TRAP GX -63.06 -65.56
55 TRAP GX -60.56 -63.06
54 TRAP GX -45.31 -60.56
53 TRAP GX -33.06 -45.31
52 TRAP GX -20.81 -33.06
51 TRAP GX -8.56 -20.81
50 TRAP GX -5.56 -8.56
49 TRAP GX -3.06 -5.56
LOAD 5 ACTIVE EP (IN SUBMERGED CONDITION)
MEMBER LOAD
25 TRAP GX 31.71 30.46
26 TRAP GX 30.46 28.95
27 TRAP GX 28.95 22.79
28 TRAP GX 22.79 16.63
29 TRAP GX 16.63 10.47
30 TRAP GX 10.47 4.3
31 TRAP GX 4.3 2.8
32 TRAP GX 2.8 1.54
56 TRAP GX -30.46 -31.71
55 TRAP GX -28.95 -30.46
54 TRAP GX -22.79 -28.95
53 TRAP GX -16.63 -22.79
52 TRAP GX -10.47 -16.63
51 TRAP GX -4.3 -10.47
50 TRAP GX -2.8 -4.3
49 TRAP GX -1.54 -2.8
LOAD 8 LL ACTIVE SURCHARGE (BS)
MEMBER LOAD
25 TO 32 UNI GX 6.71
49 TO 56 UNI GX -6.71
LOAD 9 LL ACTIVE SURCHARGE (LEFT SIDE)
MEMBER LOAD
25 TO 32 UNI GX 6.71
LOAD 10 LL ACTIVE SURCHARGE (RIGHT SIDE)
MEMBER LOAD
49 TO 56 UNI GX -6.71
LOAD 11 LL REST SURCHARGE (BS)
MEMBER LOAD
25 TO 32 UNI GX 12
49 TO 56 UNI GX -12
LOAD 12 LL REST SURCHARGE (LEFT SIDE)
MEMBER LOAD
25 TO 32 UNI GX 12
LOAD 13 LL REST SURCHARGE (RIGHT SIDE)
MEMBER LOAD
49 TO 56 UNI GX -12
LOAD 14 BRAKING FORCES (LEFT SIDE)
JOINT LOAD
27 FX 15.57
LOAD 15 BRAKING FORCES (RIGHT SIDE)
JOINT LOAD
87 FX -15.57
*TEMPERATURE CASE
LOAD 17 UNIFORM TEMP. RISE
TEMPERATURE LOAD
1 TO 8 33 TO 48 TEMP 17.5
LOAD 18 UNIFORM TEMP. FALL
TEMPERATURE LOAD
1 TO 8 33 TO 48 TEMP -17.5
************* FOR POSITIVE TEMPERATURE GRADIENT *************
LOAD 19 TEMPERATURE RISE
JOINT LOAD
27 FX 80.35 MZ -5.72
87 FX -80.35 MZ 5.72
************* FOR NEGATIVE TEMPERATURE GRADIENT *************
LOAD 20 TEMPERATURE FALL
JOINT LOAD
27 FX 39.5 MZ -0.21
87 FX -39.5 MZ 0.21
LOAD COMBINATION 500
1 1 2 1 3 1.2 17 0.5 5 1
LOAD COMBINATION 501
1 1 2 1 3 1.2 17 0.5 5 1
LOAD COMBINATION 502
1 1 2 1 3 1.2 17 0.5
LOAD COMBINATION 503
1 1 2 1 3 1.2 18 0.5 4 1
LOAD COMBINATION 504
1 1 2 1 3 1.2 18 0.5 5 1
LOAD COMBINATION 505
1 1 2 1 3 1.2 18 0.5
LOAD COMBINATION 506
11 51
LOAD COMBINATION 507
1 1 2 1 3 1.2 19 0.5 4 1
LOAD COMBINATION 508
1 1 2 1 3 1.2 19 0.5 5 1
LOAD COMBINATION 509
1 1 2 1 3 1.2 19 0.5
LOAD COMBINATION 510
1 1 2 1 3 1.2 20 0.5 4 1
LOAD COMBINATION 511
1 1 2 1 3 1.2 20 0.5 5 1
LOAD COMBINATION 512
1 1 2 1 3 1.2 20 0.5
LOAD COMBINATION 513
11 51
LOAD COMBINATION 514
1 1 2 1 3 1.2 5 1 20 0.5

PERFORM ANALYSIS
FINISH
Live Load

STAAD PLANE
START JOB INFORMATION
ENGINEER DATE 20-08-2021
END JOB INFORMATION
INPUT WIDTH 79
UNIT METER KN
JOINT COORDINATES
1 0 0 0; 2 0.25 0 0; 3 1.15 0 0; 4 3.2 0 0; 5 5.25 0 0; 6 7.3 0 0; 7 9.35 0 0;
8 10.25 0 0; 9 10.5 0 0; 11 0.25 6 0; 12 1.15 6 0; 13 3.2 6 0; 14 5.25 6 0;
15 7.3 6 0; 16 9.35 6 0; 17 10.25 6 0; 18 10.5 6 0; 20 0 0.25 0; 21 0 0.55 0;
22 0 1.775 0; 23 0 3 0; 24 0 4.225 0; 25 0 5.45 0; 26 0 5.75 0; 27 0 6 0;
28 10.5 0.25 0; 29 10.5 0.55 0; 30 10.5 1.775 0; 31 10.5 3 0; 32 10.5 4.225 0;
33 10.5 5.45 0; 34 10.5 5.75 0; 36 10.75 0 0; 37 11.65 0 0; 38 13.7 0 0;
39 15.75 0 0; 40 17.8 0 0; 41 19.85 0 0; 42 20.75 0 0; 43 21 0 0; 45 10.75 6 0;
46 11.65 6 0; 47 13.7 6 0; 48 15.75 6 0; 49 17.8 6 0; 50 19.85 6 0;
51 20.75 6 0; 52 21 6 0; 54 21 0.25 0; 55 21 0.55 0; 56 21 1.775 0; 57 21 3 0;
58 21 4.225 0; 59 21 5.45 0; 60 21 5.75 0; 62 21.25 0 0; 63 22.15 0 0;
64 24.2 0 0; 65 26.25 0 0; 66 28.3 0 0; 67 30.35 0 0; 68 31.25 0 0;
69 31.5 0 0; 80 31.5 0.25 0; 81 31.5 0.55 0; 82 31.5 1.775 0; 83 31.5 3 0;
84 31.5 4.225 0; 85 31.5 5.45 0; 86 31.5 5.75 0; 87 31.5 6 0; 88 21.25 6 0;
89 22.15 6 0; 90 24.2 6 0; 91 26.25 6 0; 92 28.3 6 0; 93 30.35 6 0;
94 31.25 6 0;
MEMBER INCIDENCES
1 27 11; 2 11 12; 3 12 13; 4 13 14; 5 14 15; 6 15 16; 7 16 17; 8 17 18;
9 18 34; 10 34 33; 11 33 32; 12 32 31; 13 31 30; 14 30 29; 15 29 28; 16 28 9;
17 9 8; 18 8 7; 19 7 6; 20 6 5; 21 5 4; 22 4 3; 23 3 2; 24 2 1; 25 1 20;
26 20 21; 27 21 22; 28 22 23; 29 23 24; 30 24 25; 31 25 26; 32 26 27; 33 18 45;
34 45 46; 35 46 47; 36 47 48; 37 48 49; 38 49 50; 39 50 51; 40 51 52; 41 52 88;
42 88 89; 43 89 90; 44 90 91; 45 91 92; 46 92 93; 47 93 94; 48 94 87; 49 87 86;
50 86 85; 51 85 84; 52 84 83; 53 83 82; 54 82 81; 55 81 80; 56 80 69; 57 69 68;
58 68 67; 59 67 66; 60 66 65; 61 65 64; 62 64 63; 63 63 62; 64 62 43; 65 43 42;
66 42 41; 67 41 40; 68 40 39; 69 39 38; 70 38 37; 71 37 36; 72 36 9; 73 43 54;
74 54 55; 75 55 56; 76 56 57; 77 57 58; 78 58 59; 79 59 60; 80 60 52;
MEMBER PROPERTY INDIAN
1 8 33 40 41 48 PRIS YD 0.8 ZD 1
2 7 34 39 42 47 PRIS YD 0.65 ZD 1
3 TO 6 35 TO 38 43 TO 46 PRIS YD 0.5 ZD 1
11 TO 14 75 TO 78 PRIS YD 0.4 ZD 1
10 31 50 79 PRIS YD 0.95 ZD 1
27 TO 30 51 TO 54 PRIS YD 0.5 ZD 1
17 24 57 64 65 72 PRIS YD 0.8 ZD 1
18 23 58 63 66 71 PRIS YD 0.65 ZD 1
19 TO 22 59 TO 62 67 TO 70 PRIS YD 0.5 ZD 1
15 26 55 74 PRIS YD 0.95 ZD 1
9 16 25 32 49 56 73 80 PRIS YD 1.4 ZD 1
DEFINE MATERIAL START
ISOTROPIC CONCRETE
E 2.21467e+006
POISSON 0.17
DENSITY 2.40262
ALPHA 1e-005
DAMP 0.05
G 946439
TYPE CONCRETE
STRENGTH FCU 2812.28
END DEFINE MATERIAL
CONSTANTS
MATERIAL CONCRETE ALL
SUPPORTS
1 FIXED BUT FZ MX MY MZ KFY 416.667
9 FIXED BUT FX FZ MX MY MZ KFY 416.667
2 8 36 42 62 68 FIXED BUT FX FZ MX MY MZ KFY 1916.67
3 7 FIXED BUT FX FZ MX MY MZ KFY 4916.67
4 TO 6 FIXED BUT FX FZ MX MY MZ KFY 6833.33
1 FIXED BUT FZ MX MY MZ KFY 416.667
43 FIXED BUT FX FZ MX MY MZ KFY 416.667
37 41 FIXED BUT FX FZ MX MY MZ KFY 4916.67
38 TO 40 FIXED BUT FX FZ MX MY MZ KFY 6833.33
1 FIXED BUT FZ MX MY MZ KFY 416.667
69 FIXED BUT FX FZ MX MY MZ KFY 416.667
2 8 FIXED BUT FX FZ MX MY MZ KFY 1916.67
63 67 FIXED BUT FX FZ MX MY MZ KFY 4916.67
64 TO 66 FIXED BUT FX FZ MX MY MZ KFY 6833.33
DEFINE MOVING LOAD
**TYPE 1 LOAD 7.7
**DIST
**TYPE 2 LOAD 3.29 6.98
**DIST -0.914
**TYPE 3 LOAD 2.52 3.2 6.14
**DIST -0.914 -0.914
**TYPE 4 LOAD 2.26 2.47 3.12 5.49
**DIST -0.914 -0.914 -0.914
**TYPE 5 LOAD 2.1 2.24 2.44 3.04 4.97
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 6 LOAD 1.99 2.09 2.22 2.41 2.96
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 7 LOAD 1.92 1.98 2.08 2.21 2.39
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 8 LOAD 1.87 1.91 1.98 2.07 2.2
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 9 LOAD 1.86 1.87 1.91 1.97 2.06
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 10 LOAD 1.86 1.86 1.87 1.9 1.96
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 11 LOAD 1.9 1.87 1.86 1.87 1.9
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 12 LOAD 1.95 1.9 1.87 1.86 1.87
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 13 LOAD 2.05 1.96 1.9 1.87 1.86
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 14 LOAD 2.18 2.06 1.97 1.91 1.87
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 15 LOAD 2.37 2.19 2.07 1.97 1.91
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 16 LOAD 2.88 2.39 2.21 2.08 1.98
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 17 LOAD 4.46 2.95 2.41 2.22 2.09
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 18 LOAD 4.07 4.87 3.02 2.43 2.24
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 19 LOAD 2.8 3.79 5.36 3.1 2.46
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 20 LOAD 2.35 2.74 3.64 5.98 3.18
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 21 LOAD 2.16 2.33 2.68 3.52 6.76
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 22 LOAD 2.03 2.15 2.31 2.63 3.42
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 23 LOAD 1.95 2.03 2.14 2.29 2.58
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 24 LOAD 1.89 1.94 2.02 2.13 2.28
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 25 LOAD 1.86 1.89 1.94 2.01 2.11
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 26 LOAD 1.86 1.86 1.88 1.93 2
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 27 LOAD 1.88 1.86 1.86 1.88 1.92
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 28 LOAD 1.92 1.88 1.86 1.86 1.88
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 29 LOAD 1.95 1.93 1.88 1.86 1.86
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 30 LOAD 1.89 1.94 1.93 1.89 1.86
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 31 LOAD 1.86 1.89 1.94 1.94 1.89
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 32 LOAD 1.86 1.86 1.89 1.93 1.95
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 33 LOAD 1.88 1.86 1.86 1.88 1.93
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 34 LOAD 1.92 1.88 1.86 1.86 1.88
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 35 LOAD 2 1.93 1.88 1.86 1.86
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 36 LOAD 2.11 2 1.93 1.89 1.86
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 37 LOAD 2.27 2.12 2.01 1.94 1.89
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 38 LOAD 2.54 2.28 2.13 2.02 1.94
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 39 LOAD 3.35 2.59 2.3 2.14 2.03
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 40 LOAD 7.4 3.45 2.65 2.32 2.15
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 41 LOAD 3.24 6.47 3.56 2.7 2.33
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 42 LOAD 2.49 3.15 5.75 3.68 2.76
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 43 LOAD 2.25 2.44 3.07 5.18 3.88
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 44 LOAD 2.09 2.23 2.42 2.99 4.72
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 45 LOAD 1.99 2.08 2.22 2.4 2.92
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 46 LOAD 1.92 1.98 2.07 2.2 2.38
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 47 LOAD 1.87 1.91 1.97 2.06 2.19
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 48 LOAD 1.86 1.87 1.91 1.96 2.05
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 49 LOAD 1.86 1.86 1.87 1.9 1.96
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 50 LOAD 1.9 1.87 1.86 1.87 1.9
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 51 LOAD 1.96 1.9 1.87 1.86 1.86
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 52 LOAD 2.05 1.96 1.91 1.87 1.86
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 53 LOAD 2.19 2.06 1.97 1.91 1.87
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 54 LOAD 2.38 2.2 2.07 1.98 1.91
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 55 LOAD 2.92 2.4 2.22 2.08 1.99
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 56 LOAD 4.69 2.99 2.42 2.23 2.09
**DIST -0.914 -0.914 -0.914 -0.914
**TYPE 57 LOAD 5.14 3.07 2.44 2.25
**DIST -0.914 -0.914 -0.914
**TYPE 58 LOAD 5.7 3.15 2.49
**DIST -0.914 -0.914
**TYPE 59 LOAD 6.41 3.23
**DIST -0.914
**TYPE 60 LOAD 7.33
**DIST
*TYPE 61 LOAD 12
*DIST
*TYPE 62 LOAD 5.26
*DIST
*TYPE 63 LOAD 3.99 5.69
*DIST -1.22
*TYPE 64 LOAD 3.57 4.2
*DIST -1.22
*TYPE 65 LOAD 3.32 3.64
*DIST -1.22
*TYPE 66 LOAD 3.15 3.37
*DIST -1.22
*TYPE 67 LOAD 3.03 3.18
*DIST -1.22
*TYPE 68 LOAD 2.96 3.05
*DIST -1.22
*TYPE 69 LOAD 2.93 2.97
*DIST -1.22
*TYPE 70 LOAD 2.94 2.94
*DIST -1.22
*TYPE 71 LOAD 3 2.94
*DIST -1.22
*TYPE 72 LOAD 3.09 2.98
*DIST -1.22
*TYPE 73 LOAD 3.24 3.06
*DIST -1.22
*TYPE 74 LOAD 3.45 3.2
*DIST -1.22
*TYPE 75 LOAD 3.76 3.4
*DIST -1.22
*TYPE 76 LOAD 4.58 3.68
*DIST -1.22
*TYPE 77 LOAD 6.87 4.32
*DIST -1.22
*TYPE 78 LOAD 6.28 5.94
*DIST -1.22
*TYPE 79 LOAD 4.46 7.77
*DIST -1.22
*TYPE 80 LOAD 3.72 4.74
*DIST -1.22
*TYPE 81 LOAD 3.43 3.8
*DIST -1.22
*TYPE 82 LOAD 3.22 3.48
*DIST -1.22
*TYPE 83 LOAD 3.08 3.26
*DIST -1.22
*TYPE 84 LOAD 2.99 3.1
*DIST -1.22
*TYPE 85 LOAD 2.94 3
*DIST -1.22
*TYPE 86 LOAD 2.94 2.95
*DIST -1.22
*TYPE 87 LOAD 2.97 2.93
*DIST -1.22
*TYPE 88 LOAD 3.04 2.96
*DIST -1.22
*TYPE 89 LOAD 3.08 3.02
*DIST -1.22
*TYPE 90 LOAD 2.99 3.11
*DIST -1.22
*TYPE 91 LOAD 2.94 3.01
*DIST -1.22
*TYPE 92 LOAD 2.93 2.95
*DIST -1.22
*TYPE 93 LOAD 2.96 2.93
*DIST -1.22
*TYPE 94 LOAD 3.04 2.95
*DIST -1.22
*TYPE 95 LOAD 3.16 3.02
*DIST -1.22
*TYPE 96 LOAD 3.33 3.12
*DIST -1.22
*TYPE 97 LOAD 3.59 3.29
*DIST -1.22
*TYPE 98 LOAD 4.04 3.53
*DIST -1.22
*TYPE 99 LOAD 5.35 3.86
*DIST -1.22
*TYPE 100 LOAD 11.32 4.98
*DIST -1.22
*TYPE 101 LOAD 5.17 9.45
*DIST -1.22
*TYPE 102 LOAD 3.95 5.59
*DIST -1.22
*TYPE 103 LOAD 3.56 4.15
*DIST -1.22
*TYPE 104 LOAD 3.31 3.63
*DIST -1.22
*TYPE 105 LOAD 3.14 3.36
*DIST -1.22
*TYPE 106 LOAD 3.03 3.17
*DIST -1.22
*TYPE 107 LOAD 2.96 3.05
*DIST -1.22
*TYPE 108 LOAD 2.93 2.97
*DIST -1.22
*TYPE 109 LOAD 2.95 2.94
*DIST -1.22
*TYPE 110 LOAD 3 2.94
*DIST -1.22
*TYPE 111 LOAD 3.1 2.98
*DIST -1.22
*TYPE 112 LOAD 3.25 3.07
*DIST -1.22
*TYPE 113 LOAD 3.46 3.21
*DIST -1.22
*TYPE 114 LOAD 3.77 3.41
*DIST -1.22
*TYPE 115 LOAD 4.64 3.7
*DIST -1.22
*TYPE 116 LOAD 7.22 4.38
*DIST -1.22
*TYPE 117 LOAD 6.07
*DIST
TYPE 121 LOAD 10.2
DIST
TYPE 122 LOAD 4.47
DIST
TYPE 123 LOAD 3.39 5.13
DIST -1.37
TYPE 124 LOAD 3.04 3.71
DIST -1.37
TYPE 125 LOAD 2.82 3.14
DIST -1.37
TYPE 126 LOAD 2.68 2.89 5.24
DIST -1.37 -3.05
TYPE 127 LOAD 2.58 2.72 3.76 7.62
DIST -1.37 -3.05 -1.37
TYPE 128 LOAD 2.52 2.61 3.15 4.18
DIST -1.37 -3.05 -1.37
TYPE 129 LOAD 2.49 2.54 2.91 3.27 6.47
DIST -1.37 -3.05 -1.37 -2.13
TYPE 130 LOAD 2.5 2.5 2.73 2.99 3.07
DIST -1.37 -3.05 -1.37 -2.13
TYPE 131 LOAD 2.55 2.5 2.61 2.79 2.35 3.73
DIST -1.37 -3.05 -1.37 -2.13 -1.52
TYPE 132 LOAD 2.63 2.53 2.54 2.65 2.13 2.67
DIST -1.37 -3.05 -1.37 -2.13 -1.52
TYPE 133 LOAD 2.75 2.59 2.5 2.56 1.98 2.23
DIST -1.37 -3.05 -1.37 -2.13 -1.52
TYPE 134 LOAD 2.93 2.7 2.5 2.51 1.88 2.05
DIST -1.37 -3.05 -1.37 -2.13 -1.52
TYPE 135 LOAD 3.19 2.86 2.52 2.49 1.81 1.93 2.45
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 136 LOAD 3.89 3.09 2.59 2.51 1.78 1.85 1.76
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 137 LOAD 5.84 3.54 2.69 2.56 1.76 1.79 1.48
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 138 LOAD 5.33 4.77 2.85 2.65 1.77 1.76 1.37
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 139 LOAD 3.79 7.93 3.07 2.78 1.8 1.76 1.28
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 140 LOAD 3.16 4.22 3.5 2.98 1.86 1.78 1.23
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 141 LOAD 2.91 3.28 4.68 3.26 1.95 1.83 1.19
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 142 LOAD 2.74 2.99 8.5 4.14 2.08 1.9 1.18
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 143 LOAD 2.62 2.79 4.28 7.34 2.27 2.01 1.17
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 144 LOAD 2.54 2.65 3.3 4.88 2.81 2.16 1.19
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 145 LOAD 2.5 2.56 3.01 3.59 4.47 2.46 1.22
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 146 LOAD 2.49 2.51 2.8 3.1 3.62 3.28 1.27
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 147 LOAD 2.52 2.49 2.66 2.87 2.62 6.18 1.34
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 148 LOAD 2.58 2.51 2.57 2.71 2.22 3.04 1.45
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 149 LOAD 2.62 2.56 2.51 2.6 2.04 2.34 1.65
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 150 LOAD 2.54 2.64 2.49 2.53 1.92 2.13 2.22
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 151 LOAD 2.5 2.57 2.51 2.5 1.84 1.98 3.89
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 152 LOAD 2.49 2.51 2.55 2.5 1.79 1.88 2
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 153 LOAD 2.52 2.49 2.64 2.53 1.76 1.81 1.55
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 154 LOAD 2.58 2.51 2.57 2.6 1.76 1.77 1.41
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 155 LOAD 2.68 2.55 2.51 2.6 1.78 1.76 1.32
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 156 LOAD 2.83 2.64 2.49 2.53 1.83 1.77 1.25
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 157 LOAD 3.05 2.77 2.51 2.5 1.84 1.8 1.21
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 158 LOAD 3.43 2.96 2.55 2.5 1.79 1.86 1.18
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 159 LOAD 4.55 3.23 2.63 2.53 1.76 1.82 1.17
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 160 LOAD 9.62 4.04 2.76 2.6 1.76 1.78 1.18
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 161 LOAD 4.4 6.68 2.95 2.71 1.78 1.76 1.2
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 162 LOAD 3.36 5.03 3.22 2.87 1.83 1.77 1.24
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 163 LOAD 3.03 3.66 3.98 3.11 1.9 1.8 1.21
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 164 LOAD 2.82 3.12 6.33 3.61 2.01 1.86 1.18
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 165 LOAD 2.67 2.88 5.13 4.91 2.17 1.95 1.17
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 166 LOAD 2.57 2.72 3.71 7.16 2.47 2.08 1.18
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 167 LOAD 2.52 2.6 3.14 4.11 3.3 2.27 1.2
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 168 LOAD 2.49 2.53 2.89 3.25 6 2.79 1.24
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 169 LOAD 2.5 2.5 2.72 2.98 3.02 4.38 1.3
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 170 LOAD 2.55 2.5 2.61 2.78 2.33 3.65 1.39
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 171 LOAD 2.63 2.53 2.54 2.65 2.12 2.63 1.52
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 172 LOAD 2.76 2.6 2.5 2.56 1.98 2.22 1.88
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 173 LOAD 2.94 2.71 2.5 2.51 1.88 2.05 3.04
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 174 LOAD 3.21 2.87 2.53 2.49 1.81 1.93 2.4
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 175 LOAD 3.95 3.1 2.59 2.51 1.77 1.84 1.74
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 176 LOAD 6.14 3.58 2.7 2.56 1.76 1.79 1.47
DIST -1.37 -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 177 LOAD 4.86 2.86 2.65 1.77 1.76 1.36
DIST -3.05 -1.37 -2.13 -1.52 -3.96
TYPE 178 LOAD 3.09 2.79 1.8 1.76 1.28
DIST -1.37 -2.13 -1.52 -3.96
TYPE 179 LOAD 3.54 2.99 1.86 1.78 1.23
DIST -1.37 -2.13 -1.52 -3.96
TYPE 180 LOAD 4.77 3.28 1.96 1.83 1.19
DIST -1.37 -2.13 -1.52 -3.96

**LOAD GENERATION 1
**TYPE 1 0 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 2 1 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 3 2 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 4 3 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 5 4 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 6 5 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 7 6 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 8 7 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 9 8 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 10 9 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 11 10 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 12 11 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 13 12 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 14 13 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 15 14 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 16 15 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 17 16 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 18 17 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 19 18 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 20 19 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 21 20 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 22 21 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 23 22 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 24 23 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 25 24 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 26 25 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 27 26 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 28 27 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 29 28 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 30 29 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 31 30 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 32 31 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 33 32 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 34 33 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 35 34 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 36 35 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 37 36 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 38 37 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 39 38 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 40 39 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 41 40 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 42 41 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 43 42 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 44 43 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 45 44 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 46 45 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 47 46 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 48 47 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 49 48 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 50 49 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 51 50 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 52 51 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 53 52 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 54 53 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 55 54 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 56 55 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 57 56 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 58 57 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 59 58 6 0 XINC 0.0001
**LOAD GENERATION 1
**TYPE 60 59 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 61 0 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 62 1 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 63 2 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 64 3 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 65 4 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 66 5 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 67 6 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 68 7 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 69 8 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 70 9 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 71 10 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 72 11 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 73 12 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 74 13 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 75 14 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 76 15 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 77 16 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 78 17 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 79 18 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 80 19 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 81 20 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 82 21 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 83 22 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 84 23 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 85 24 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 86 25 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 87 26 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 88 27 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 89 28 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 90 29 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 91 30 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 92 31 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 93 32 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 94 33 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 95 34 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 96 35 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 97 36 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 98 37 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 99 38 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 100 39 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 101 40 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 102 41 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 103 42 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 104 43 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 105 44 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 106 45 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 107 46 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 108 47 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 109 48 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 110 49 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 111 50 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 112 51 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 113 52 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 114 53 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 115 54 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 116 55 6 0 XINC 0.0001
*LOAD GENERATION 1
*TYPE 117 56 6 0 XINC 0.0001

LOAD GENERATION 1
TYPE 121 0 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 122 1 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 123 2 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 124 3 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 125 4 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 126 5 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 127 6 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 128 7 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 129 8 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 130 9 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 131 10 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 132 11 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 133 12 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 134 13 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 135 14 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 136 15 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 137 16 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 138 17 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 139 18 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 140 19 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 141 20 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 142 21 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 143 22 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 144 23 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 145 24 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 146 25 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 147 26 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 148 27 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 149 28 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 150 29 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 151 30 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 152 31 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 153 32 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 154 33 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 155 34 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 156 35 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 157 36 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 158 37 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 159 38 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 160 39 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 161 40 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 162 41 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 163 42 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 164 43 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 165 44 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 166 45 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 167 46 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 168 47 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 169 48 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 170 49 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 171 50 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 172 51 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 173 52 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 174 53 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 175 54 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 176 55 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 177 56 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 178 57 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 179 58 6 0 XINC 0.0001
LOAD GENERATION 1
TYPE 180 59 6 0 XINC 0.0001

PERFORM ANALYSIS
FINISH