Scribd
Upload
58 views15 pages

Teco Motor Lubrication

D

Uploaded by

FRANCO BTZ
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
58 views15 pages

Teco Motor Lubrication

D

Uploaded by

FRANCO BTZ
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 15

Lubrication Instruction

Motors – TECO
Lubrication Instruction – Motor TECO
Table of Contents
1.0 Details of Grease & Greasing system

2.0 Details – Motor Grease points & Greasing

3.0 Greasing Schedule – 1, for Motors (Before first operation)

4.0 Greasing Schedule – 2, for Motors (Based on Lubrication Interval)

5.0 Long Storage Instructions.

6.0 Procedure to load 390g grease cartridge into Grease Gun

2 © Metso
RESTRICTED

TECO Motors Greasing


1.0 Details of Grease & Greasing system

• Following is recommended grease to be


used for TECO motor Lubrication:
- Unirex R3, Make : Mobil
- Metso part code for 390 gram standard Metso part code for suitable hand
cartridge is MM045637 grease gun 705600441000 with
mouth piece/ coupler of DIN1283.

3 © Metso
TECO Motors
2.0 Details – Motor Grease points & Greasing
Motors are fitted with snap on greasing nipples and an outlet at the bottom of the
bearing housing to let out any overfill of grease. As shown in photo below
Greasing Points

Greasing of Motors

4 © Metso
TECO Motors
3.0 Greasing Schedule – 1, (Before first operation / new bearing)
This Greasing schedule 1 has to be followed before the first operation of the motor Or after installing new
bearings, the details of which are as below:
The bearing have to greased with the recommended grease prior to the first operation of the motor. During
the process of greasing the shaft needs to be intermittently rotated . If grease overflows via grease relief
opening during greasing , stop doing it immediately.

5 © Metso
TECO Motors
4.0 Greasing Schedule – 2, for Motors (Based on Lubrication Interval)
The Greasing schedule 2 needs to be followed when the motors is put to operation and the lubrication has
to be done as per the lubrication interval cycle .

Attention:
• For re-greasing use only the grease specified on the re-greasing nameplate . (Don’t mix with different
grade or make)
• Grease nipples must be clean to avoid dirt penetrating the bearings during re-greasing
• Grease relief openings must be open and have free access so that used grease can escape unhindered
• It is preferable to re-grease the bearings during operation for better grease distribution.
• Make sure that this work is done by trained personnel only and live and moving parts are safely covered.
• If this is impossible (i.e. danger from rotating parts) re-grease when stationary. In this case use only half
of the grease amount specified on the re-greasing nameplate. Restart the equipment for at least one
minute of operation. Shut down again and re-grease with the remaining half of the grease amount
specified. Restart for operation

6 © Metso
TECO Motors
4.0 Greasing Schedule – 2, for Motors (Based on Lubrication Interval)
Follow the greasing cycle as per the Lubrication interval cycle along with the recommended grease as
shown in the table below. Also note Pole of the motor, Normally it is 4 pole

7 © Metso
TECO Motors
4.0 Greasing Schedule – 2, for Motors (Based on Lubrication Interval)
Follow the greasing cycle as per the Lubrication interval cycle along with the recommended grease as
shown in the table below. Also note Pole of the motor, Normally it is 4 pole

8 © Metso
TECO Motors
5.0 Long storage Instructions

When motors if not installed for a long period of time must be


• Stored in High and dry , well ventilated place and without direct sun.
• The motor has to be covered and should be put on pallet to prevent moisture.

• If the Motor is not used for about three months , the shaft has to be rotated .

• If the motors has not been operated for more that six months from the date of supply from
the factory, the grease needs to be replaced.

9 © Metso
6.0 Procedure to load 380g grease cartridge into Grease Gun
Grease gun nomenclature - Lever type

10 © Metso
Steps to load 380g grease cartridge into Grease Gun

1
1
2

1. Pull back the Plunger Rod Handle all the way back & lock it with the End cap.
2. Unscrew Grease Gun Head from the Barrel counter-clockwise

11 © Metso
Steps to load 380g grease cartridge into Grease Gun
Plastic cap
3

Grease Cartridge
3. Remove the plastic cap from the open end of the Grease Cartridge & fully
insert into empty Grease Barrel. Make sure the rim of the Cartridge is seated
on the rim of the Barrel.

12 © Metso
Steps to load 380g grease cartridge into Grease Gun

4 5

4. Remove the metal Pull tab seal from the Grease Cartridge
5. Screw back the Grease gun Head onto the Barrel.

13 © Metso
Steps to load 380g grease cartridge into Grease Gun

6 7

6. Disconnect the Plunger Rod from the End Cap.


7. Bleed out trapped air in the grease to come.
8. Start operating the Grease Gun Handle till grease starts flowing out continuously.
(Note that the first discharge of grease may have some air bubbles). If grease is
accompanied with air bubbles, repeat step 7 to Prime the Grease Gun

14 © Metso
www.metso.com

company/metso metsoworld metsogroup metsoworld metsogroup

You might also like