NAME: _______________________________________________________ BATCH: _________________DATE:_______________

CPP - CURRENT ELECTRICITY

* MARK IS MORE THAN ONE CORRECT QUESTIONS.
SECTION (A) : DEFINITION OF CURRENT
CURRENT,, CURRENT DENSITIES & DRIFT VEL OCITIES
VELOCITIES
A.1 Calculate the number of electrons crossing a given cross-section in 1 second to constitute a current of
1 A.

A.2 Estimate the average drift speed of conduction electrons in a copper wire of cross-sectional area 1.0 ×
10–7 m2 carrying a current of 1.5 A. Assume that each copper atom contributes roughly one conduction
electron. The density of copper is 9.0 × 103 kg m –3 and its atomic mass is 63.5 u.

A.3 The current through a wire depends on time as i = i0 + αt, where i0 = 10 A and α = 4 A/s. Find the charge
crossed through a section of the wire in 10 seconds, and average current for that interval.
A.4 A current of 1.0 A exists in a copper wire of cross-section 1.0 mm2. Assuming one free electron per atom
calculate the drift speed of the free electrons in the wire. The density of copper is 9000 km/m3. (atomic weight
of copper = 63.5 and Avagadro number = 6 × 1023)

A.5 Consider a wire of length 4m and cross-sectional area 1 mm2 carrying a current of 2A. If each cubic metre of
the material contains 1029 free electrons, find the average time taken by an electron to cross the length of
wire.

A.6 The drift velocity of electrons in a conducting wire is of the order of 1mm/s, yet the bulb glows very quickly
after the switch is put on because
(A) the random speed of electrons is very high, of the order of 106 m/s
(B) the electrons transfer their energy very quickly through collisions
(C) electric field is set up in the wire very quickly, producing a current through each cross section, almost
intantaneousty
(D) All of above

A.7 Read the following statements carefully :

Y : The resistivity of a semiconductor decreases with increase of temperature
Z : In a conducting solid, the rate of collisions between free electrons and ions increases with
increase of temperature
Select the correct statement from the following
(A) Y is true but Z is false (B) Y is false but Z is true
(C) Both Y and Z are true (D) Y is true and Z is the correct reason for Y

A.8 A silver wire of length 10 metre and cross-sectional area 10–8 m2 is suspended vertically and a weight of
10 N is attached to it. Young’s modulus of silver and its resistivity are 7 × 10 10 N/m2 and 1.59 × 10–8 Ω-
m respectively. The increase in its resistance is equal to
(A) 0.0455 Ω (B) 0.455 Ω (C) 0.91 Ω (D) 0.091 Ω

SECTION (B) : RESISTANCE

RESISTANCE
B.1 The resistance of an electric heater is 25 Ω. Its ends are connected to the poles of a 90 V battery. How
much current will flow in the heater wire ?

B.2 Calculate the resistance of an aluminium wire of length 50 cm and cross-sectional area 2.0 mm2. The
resistivity of aluminium is ρ = 2.6 × 10–8 Ω - m.

B.3 A potential difference of 200 volt is applied to a coil at a temperature of 15ºC and the current is 10 A.
What will be the mean temperature of the coil when the current has fallen to 5 A, the applied voltage
1
being the same as before? Given : α = ºC–1.
234

Page # 1
B.4 What length of a copper wire of cross-sectional area 0.01 mm2 will be needed to prepare a resistance of
1kΩ? Resistivity of copper = 1.7 × 10–8 Ω-m.

B.5 A rectangular carbon block has dimensions 1.0 cm × 1.0 cm ×

50 cm. Resistances are measured, first across two square
ends and then across two rectangular ends, respectively. If
resistivity of carbon is 3.5 × 10–5 Ω-m, then values of measured
resistances respectively are:
(A) 17.5 × 10–2 Ω, 7 × 10–5 Ω
(B) 7 × 10–5 Ω, 7.5 × 10 –2 Ω
(C) 17.5 × 10–4 Ω, 7 × 10–7 Ω
(D) 7.5 Ω, 7 × 10–2 Ω

B.6 A wire is in the form of a tetrahedron. The resistance of each edge is r. The equivalent resistances
between corners 1–2 and 1–3 are respectively
r r
(A) , (B) r, r
2 2
r r
(C) ,r (D) r,
2 2

B.7 The equivalent resistance between A and B will be (in Ω)

(A) 2/7 (B) 8
(C) 4/3 (D) 7/3

B.8 In the figure shown the current flowing through 2 R is :

(A) from left to right (B) from right to left

(C) no current (D) None of these

B.9 The equivalent resistance between the points A and B is :

36
(A) Ω (B) 10 Ω
7
85
(C) Ω (D) none of these
7

B.10 The equivalent resistance between points A and B is :

(A) 32.5 Ω (B) 22.5 Ω

(C) 2.5 Ω (D) 45.5 Ω

B.11 In the circuit shown in figure

(A) power supplied by the battery is 200 watt

(B) current flowing in the circuit is 5 A
(C) potential difference across 4 Ω resistance is equal to
the potential difference across 6Ω resistance
(D) current in wire AB is zero

Page # 2
B.12 (a) The current density across a cylindrical conductor of radius R varies according to the equation
 r 
J = J0 1 −  , where r = distance from the axis. Thus the current density is a maximum J0 at the
 R
axis r = 0 and decreases linearly to zero at the surface r = R. Calculate the current in terms of J0 and
the conductor's cross-sectional area A = π R2.
(b) Suppose that instead the current density is a maximum J0 at the surface and decreases linearly to

zero at the axis so that J = J0 r . Calculate the current.

R
B.13 A network of resistance is constructed with R1 and R2 as shown in
the figure. The potential at the points 1, 2, 3,........, N are V1, V2,
V3,........., Vn respectively each having a potential K time smaller
than previous one. Find:
R1 R2
(i) R2 and R 3 in terms of K.
(ii) Current that passes through the resistance R2 nearest to the V0 in terms V0, K and R3.

B.14 The figure is made of a uniform wire and represents a regular five
pointed star. The resistance of a section EL is 2 ohm. Find the
1
resistance of the star across F and C. (sin 18º ~ )
3

B.15 The resistance of each resistor in the circuit diagram shown in figure
is the same and equal to R. The voltage across the terminals is U.
Determine the current I in the leads if their resistance can be
neglected.

B.16 A hemispherical network of radius a is made by using a conducting wire of resistance per unit length 'r'. Find
the equivalent resistance across OP.

B.17 In the circuit shown in figure, all wires have equal resistance r. The
equivalent resistance between A and B is ___________ .

SECTION (C) : POWER, ENER

POWER, ENERGGY, BATTER
BATTER
TTERYY, EMF
EMF,, TERMINAL VOL
VOL TAGE & KIR
OLT CHOFF’S LA
KIRCHOFF’S WS
LAW
C.1 In following diagram boxes may contain resistor or battery or any other element

then determine in each case

(a) E.m.f. of battery
(b) Battery is acting as a source or load
(c) Potential difference across each battery
(d) Power input to the battery or output by the battery.
(e) The rate at which heat is generaled inside the battery.
(f) The rate at which the chemical energy of the cell is consumed or increased.
(g) Potential difference across box
(h) Power output across box.

Page # 3
C.2 The figure shows the current Ι in a single-loop circuit with a battery B and resistance R (and wires of
negligible resistance).
(a) Should the emf arrow at B be drawn leftward or rightward?
At points a, b and c, rank
(b) The magnitude of the current,
(c) The electric potential, and
(d) The electric potential energy of the charge carriers
(electron), greatest first.

C.3 Figure shows a part of an electric circuit. The potentials

at the points a, b and c are 30 V, 12V and 2V respectively.
Find the currents through the three resistors.

C.4 For driving a current of 3 ampere for 5 minutes in an electrical circuit, 900 joule of work is to be done.
Find the emf of the source in the circuit.
C.5 (a) A car has a fresh storage battery of emf 12 V and internal resistance 5.0 × 10–2 Ω. If the starter
draws a current of 90 A, what is the terminal voltage of the battery when the starter is on ?
(b) After long use, the internal resistance of the storage battery increases to 500 Ω. What maximum
current can be drawn from the battery? Assume the emf of the battery to remains unchanged.
(c) If the discharged battery is charged by an external emf source, is the terminal voltage of the battery
during charging greater or less than its emf 12 V?

C.6 The potential difference between the terminals of a 6.0 V battery is 7.2 V when it is being charged by a
current of 2.0 A. What is the internal resistance of the battery ?

C.7 Find the current through the 10 Ω resistor shown in figure

C.8 In following circuit potential of point ‘A’ is zero then determine

(a) Potential of each point
(b) Potential difference across each resistance
(c) Identify the battery which act as a source
(d) Current in each battery
(e) Which resistance consume maximum power
(f) Which battery consume or increased maximum energy.

C.9 One kilowatt electric heater is to be used with 220 V D.C. supply.
(a) What is the current in the heater.
(b) What is its resistance.
(c) What is the power dissipated in the heater.
(d) How much heat in calories is produced per second.
(e) How many grams of water at 100º C will be converted per minute into steam at 100º C
with the heater. (latent heat of vaporisation of water = 540 cal/g)]

C.10 The efficiency of a cell when connected to a resistance R is 60%.

What will be its efficiency if the external resistance is increased to
six times.

C.11 An electric heating element consumes 500 W when connected to a 100 V line. If the line voltage
becomes 150 V, the power consumed will be :
(A) 500 W (B) 750 W (C) 1000 W (D) 1125 W

Page # 4
C.12 If internal resistance of a cell is proportional to current drawn from the cell. Then the best representation
of terminal potential difference of a cell with current drawn from cell will be:

(A) (B) (C) (D)

C.13 A resistor of resistance R is connected to a cell of internal resistance 5 Ω. The value of R is varied from
1 Ω to 5 Ω. The power consumed by R:
(A) increases continuously (B) decreases continuously
(C) first decreases then increases (D) first increases then decreases.

C.14 In the figure shown the thermal power generated in ' y ' is
maximum when y = 4 Ω. Then X is:
(A) 2 Ω (B) 3 Ω
(C) 1 Ω (D) 6 Ω

C.15 A cell of emf E having an internal resistance r is connected to

an external resistance R. The potential difference V across the
resistance R varies with R as shown in figure by the curve :
(A) A (B) B
(C) C (D) D

C.16 In the figure shown part of circuit :

(A) current will flow from A to B (B) current may flow from A to B
(C) current will flow from B to A (D) the direction of current will depend on r.

C.17 A battery of emf E and internal resistance r is connected across a resistance R. Resistance R can be
adjusted to any value greater than or equal to zero. A graph is plotted between the current passing through
the resistance (i) and potential difference (V) across it. Select the correct alternative (s)
(A) internal resistance of the battery is 5Ω
(B) emf of the battery is 10 V

(C) maximum current which can be taken from the battery is 2 A

(D) V-i graph can never be a straight line as shown in figure.

C.18 Potential difference across the terminals of a non ideal battery is

(A) zero when it is short circuited
(B) less than its emf when current flows from negative terminal to positive terminal inside the battery
(C) zero when no current is drawn from the battery
(D) greater than its emf when current flows from positive terminal to negative inside the battery.

SECTION : (D) EQUIVALENT OF RESIST

EQUIVALENT ANCE
RESISTANCE
D.1 In given circuit determine
(a) Equivalent resistance (Including internal resistance).
(b) Current in each resistance
(c) Potential difference across each resistance
(d) The rate at which the chemical energy of the cell is consumed
(e) The rate at which heat is generated inside the battery
(f) Electric power output
(g) Potential difference across battery
(h) Which resistance consumes maximum power
(i) Power dissipated in 3 Ω resistance.

Page # 5
D.2 In given circuit determine
(a) Equivalent resistanace (Including internal resistance).
(b) Current i, i1, i2 and i3
(c) Potential difference across battery and each resistance
(d) The rate at which the chemical energy of the cell is consumed
(e) The rate at which heat is generated inside the battery
(f) Electric power output
(g) Which resistance consumes maximum power ?
(h) Power dissipated across 4Ω resistance

D.3 Three equal resistors connected in series across a source of emf together dissipate 10 watts of power.
What would be the power dissipated if the same resistors are connected in parallel across the same
source of emf ? [JEE - 72]

D.4 If the reading of ammeter A1 in figure is 2.4 A, what will

the ammeters A2 and A3 read ? Neglect the resistance
of the ammeters.

D.5 The resistance of the rheostat shown in figure is 30 Ω. Neglecting

the meter resistance, find the minimum and maximum currents
through the ammeter as the rheostat is varies.

D.6 Figure shows a part of a circuit. If a current of 12 mA exists in the

5kΩ resistor, find the currents in the other three resistors. What is
the potential difference between the points A and B ?

D.7 The given Wheatstone bridge is showing no deflection in the

galvanometer joined between the points B and D (Figure).
Calculate the value of R.

D.8 A wire of resistance 0.1 ohm cm–1 bent to form a square ABCD of side 10 cm. A similar wire is connected
between the corners B and D to form the diagonal BD. Find the effective resistance of this combination
between corners A and C. IF a 2V battery of neglgible internal resistance is connected across A and C
calculate the total power dissipated.
10Ω 20Ω
D.9 Consider the circuit shown in figure. Find the current
through the 10Ω resistor when the switch S is S
(a) open (b) closed.
3V
D.10 Find the equivalent resistance of the circuit given in figure between the following point:
(i) A and B (ii) C and D
(iii) E and F (iv) A and F
(v) A and C

Page # 6
D.11 An infinite ladder network of resistances is constructed with 1 ohm and 2 ohm resistances. The 6 V
battery between A and B has negligible internal resistance.

Show that effective resistance between A and B is 2 ohm.

What is the current that passes through 2 Ω resistance nearest to the battery?
D.12 As shown in figure a variable rheostat of 2 k Ω is used to control the potential difference across 500
ohm load. (i) If the resistance AB is 500 Ω, what is the potential difference across the load ? (ii) If the
load is removed, what should be the resistance at BC to get 40 volt between B and C ?

D.13 An electric current of 5 amp. is divided in three branches forming a parallel combination. The length of
the wire in the three branches are in the ratio, 2,3 and 4; their diameters are in the ratio 3, 4 and 5. Find
the currents in each branch if the wire of the same material.

D.14 Two electric bulbs, each designed to operate with a power of 500 watts in 220 volt line, are in series
with a 110 volt line. What will be the power generated by each bulb ?

D.15 All resistance in diagram (fig.) are in ohms. Find the

effective resistance between the points A and B.

D.16 Three equal resistance each of R ohm are connected as shown

R R R
in figure. A battery of 2 volts of internal resistance 0.1 ohm is
connected across the circuit. Calculate the value of R for which
the heat generated in the circuit is maximum.
2V
D.17 A battery of internal resistance 4 ohm is connected to the
network of resistance as shown. In the order that the maximum
power can be delivered to the network, the value of R in ohm
should be :
(A) 4/9 (B) 2
(C) 8/3 (D) 18

D.18 Two coils connected in series have resistances 600 Ω and 300 Ω and temperature coefficient of resistivity
0.001 k–1 and 0.004 k–1 respectively at 200C.
(a) The resistance of the combination at temperature 50°C is
(A) 426 Ω (B) 954 Ω (C) 1806 Ω (D) 214 Ω
(b) The effective temperature coefficient of the combination is
(A) 0.001 degree–1 (B) 0.003 degree–1
–1
(C) 0.002 degree (D) 0.004 degree–1

Page # 7
D.19 Equivalent resistance between point C and D
in the combination of resistance shown is :
(A) 3 Ω (B) 1 Ω
(C) 1.5 Ω (D) 0.5 Ω
D.20 In the ladder network shown, current through the resistor 3 Ω is 0.25 A. The input voltage ‘V’ is equal to
(A) 10 V
(B) 20 V
(C) 5 V
(D) 7.5 V
D.21 An electric tea kettle has two electric heating coils. When one of the coils is switched on the tea
begins to boil in 6 minutes. When the other is switched on, the boiling begins in
8 minutes.
(a) If both the coils are now arranged in series and switched on, boiling starts in
(A) 24/7 minutes (B) 12 minutes
(C) 14 minutes (D) 4 minutes
(b) If the coils are arranged in parallel and switched on, then boiling starts in
(A) 24/7 minutes (B) 12 minutes
(C) 14 minutes (D) 4 minutes
D.22 If 2 bulbs rated 2.5 W – 110 V and 100 W – 110 V are connected in series to a 220 V supply then
(A) 2.5 W bulb will fuse (B) 100 W bulb will fuse
(C) both will fuse (D) both will not fuse

D.23 The current through the circuit shown in figure is 1 A. If each of the 4Ω
resistor is replaced by 2Ω resistor, the current in circuit will become
nearly :
(A) 1.11 A (B) 1.25
(C) 1.34 A (D) 1.68 A

D.24 A 50 W bulb is in series with a room heater and the combination is connected across the mains. To get max.
heater output, the 50 W bulb should be replaced by
(A) 25 W (B) 10 W (C) 100 W (D) 200 W

D.25 Five resistance are connected as shown in fig. The effective resistance between the points A and B is -

(A) 10/3 Ω (B) 20/3 Ω (C) 15 Ω (D) 6 Ω

D.26 Four identical bulbs each rated 100 watt, 220 volts
are connected across a battery as shown. The total
electric power consumed by the bulbs is: 220V
(A) 75 watt (B) 400 watt
(C) 300 watt (D) 400/3 watt

D.27 The current i in the circuit of fig. is -

1 1
(A) amp. (B) amp.
45 15
1 1
(C) amp. (D) amp.
10 5

Page # 8
SECTION (E) : COMBINATION OF CELLS
COMBINATION
E.1 Six lead-acid type of secondary cells, each of emf 2.0 V and internal resistance 0.015 Ω, are joined in
series to provide a supply to a resistance of 8.5 Ω. Determine : (i) the current drawn from the supply
and (ii) its terminal voltage.
Ι
A > B

E.2 In the figure each cell has an emf of 1.5 V and

internal resistance of 0.40 Ω. Calculate:
12W 18W 36W 1.8W
(i) current Ι
(ii) current in the 36 Ω resistor
(iii) potential difference across A and B. D C

E.3 12 cells each having the same emf are connected in series and are kept in a closed box. Some of the cells
are wrongly connected. This battery is connected in series with an ammeter and two cells identical with each
other and also identical with the previous cells. The current is 3 A when the external cells aid this battery and
is 2 A when the cells oppose the battery. How many cells in the battery are wrongly connected?

E.4 How would you connect (series and parallel) 24 cells, each of internal resistance 1 ohm, so as to get
maximum output across the load of 10 ohm.

E.5 Two nonideal batteries are connected in parallel. Consider the following statements
(I) The equivalent emf is smaller than either of the two emfs.
(II) The equivalent internal resistance is smaller than either of the two internal resistance.
(A) Both I and II are correct (B) I is correct but II is wrong
(C) II is correct but I is wrong (D) Each of I and II is wrong.

E.6 A series parallel combination battery consisting of a large number N = 300 of identical cells, each with
an internal resistances r = 0.3 Ω, is loaded with an external resistance R = 10 Ω. The number ‘n’ of
parallel groups consisting of an equal number of cells connected in series, at which the external
resistance generates the highest thermal power is
(A) 2 (B) 3 (C) 4 (D) 6

E.7 A galvanometer together with an unknown resistance in series

is connected across two identical batteries of each 1.5 V. When
the batteries are connected in series, the galvanometer records
a current 1 A and when the batteries are in parallel, the current
s 0.6 A. The internal resistance of the batteries is

E.8 N cells each of e.m.f. E & identical resistance r are grouped into sets of K cells connected in series.
The (N/K) sets are connected in parallel to a load of resistance R, then;
NR
(A) Maximum power is delivered to the load if K = .
r
r
(B) Maximum power is delivered to the load if K =
NR
NE2
(C) Maximum power delivered to the load is
4r
E2
(D) Maximum power delivered to the load is
4Nr

E.9 Two cells of e.m.f. 10 V & 15 V are connected in parallel to

each other between points A & B. The cell of e.m.f. 10 V is
ideal but the cell of e.m.f. 15 V has internal resistance 1 Ω.
The equivalent e.m.f. between A and B is:
(A) 12.5 V (B) not defined
(C) 15 V (D) 10 V

Page # 9
E.10 A battery is made by joining m rows of identical cells in parallel. Each row consists of n cells joined in series.
This battery sends a maximum current I in a given external resistor. Now the cells are so arranged that
instead of m rows, n rows are joined in parallel and each row consists of m cells joined in series. Find the
current through the same external resistor

E.11 In the circuit shown in fig. E1 = 3 volt, E2 = 2 volt, E3 = 1 volt

and R = r1 = r2 = r3 = 1 ohm.
(i) Find potential difference between the points A and
B and the currents through each branch.
(ii) If r2 is short circuited and the point A is connected to
point B, find the currents through E1, E2, E3 and the resistor R.
[JEE - 81]

E.12 In the circuit shown in fig. E, F, G and H are cells of emf 2, 1,3
and 1 volts and their internal resistances are 2, 1, 3 and 1 ohm
respectively. Calculate.
[JEE - 81]
(i) The potential difference between B and D and
(ii) The potential difference across the terminals of each of the cells G and H.
2 4 1
(A) Ω (B) 1 Ω (C) Ω (D) Ω
3 3 3

SECTION (F) INSTRUMENTS

F.1 A galvanometer having 30 divisions has current sensitivity of 20 µA/div. It has a resistance of 25 ohm. How
will you convert it to an ammeter measuring upto 1 ampere ? How will you now convert this ammeter into a
voltmeter reading upto 1 volt ?

F.2 A galvanometer has a resistance of 30 ohm and a current of 2 mA is needed to give a full scale deflection.
What is the resistance needed and how is it to be connected to convert the galvanometer.
(a) Into an ammeter of 0.3 ampere range
(b) Into a voltmeter of 0.2 volt range ?
+ – 120 V –
F.3 A D.C. supply of 120 volt is connected to a large registance X.
A volt meter of resistance 10 kΩ. Placed in series in the circuit
reads 4 volts. What is the value of X? What do you think is the
purpose in using a voltmeter, instead of an ammeter, to X 10kΩ
determine the large resistance X? V

F.4 A voltmeter of resistance 400Ω is used to measures the potential

difference across the 100Ω resistor in the circuit shown in the
figure. (a) What will be the reading of the voltmeter ? (b) What
was the potential difference across 100 Ω before the voltmeter
was connected ?

F.5 The ammeter shown in figure consists of a 480 Ω coil connected

in parallel to a 20 Ω shunt. Find the reading of the ammeter.

Page # 10
F.6 Figure shows a potentiometer with a cell of emf 2.0 V and internal resistance 0.04 Ω maintaining a
potential drop across the resistor wire AB. A standard cell which maintains a constant emf of 1.02 V
(for very moderate currents up to a few ampere) gives a balance point of 67.3 cm length of the wire. To
ensure very low currents drawn from the standard cell, a very high resistance of 600 kΩ is put in series
with it which is shorted close to the balance point. The standard cell is then replaced by a cell of
unknown emf E and the balance point found similarly turns out to be at 82.3 cm length of the wire.
(a) What is the value of E ?

(b) What purpose does the high resistance of 600 kΩ have ?

(c) Is the balance point affected by this high resistance?

(d) Is the balance point affected by the internal resistance of the driver cell?
(e) Would the method work in the above situation if the driver cell of the potentiometer had an emf of 1.0
V instead of 2.0 V?
(f) Would the circuit work well for determining externally small emf, say, of the order of few mV (such
typical emf of thermocouple)?

F.7 Figure shows a metre bridge (which is nothing but a practical Wheatstone Bridge) consisting of two
resistors X and Y together in parallel with a metre long constantan wire of uniform cross-section. With
the help of a movable contact D, one can change the ratio of the resistances of the two segments of the
wire until a sensitive galvanometer G connected across B and D shows no deflection. The null point is
found to be at a distance of 33.7 cm from the end A. The resistor Y is shunted by a resistance of 12.0
Ω and the nul point is found to shift by a distance of 18.2 cm. Determine the resistance of X and Y.

F.8 The meter-bridge wire AB shown in figure is 50 cm

long. When AD = 30 cm, no deflection occurs in
the galvanometer. Find R.

F.8 A battery of emf 1.4 V and internal resistance 2 Ω is connected to a resistor of 100 Ω through an ammeter.
The resistance of the ammeter is 4/3 Ω. A voltmeter has also been connected to find the potential difference
across the resistor.
(i) Draw the circuit diagram.
(ii) The ammeter reads 0.02 A. What is the resistance of the voltmeter.
(iii) The voltmeter read 1.10 V, what is the zero error in the voltmeter.

F.9 The reading of voltmeter is

(A) 50V
(B) 60 V
(C) 40V
(D) none

Page # 11
F.10 When a galvanometer is shunted with a 4Ω resistance, the deflection is reduced to one - fifth. If the
galvanometer is further shunted with a 2Ω wire, the further reduction (find the ratio of decrease in
current to the previous current) in the deflection will be (the main current remains the same).
(A) (8/13) of the deflection when shunted with 4Ω only
(B) (5/13) of the deflection when shunted with 4Ω only
(C) (3/4) of the deflection when shunted with 4Ω only
(D) (3/13) of the deflection when shunted with 4Ω only

F.11 In the circuit shown, reading of the voltmeter connected across 60V
400 Ω resistance is 30 V. If it is connected across 300 Ω
resistance then reading will be 300W 400W
(A) 45 V (B) 32.5 V
(C) 22.5 V (D) 18 V
V
F.12 Select the correct alternative(s):
A micrometer has a resistance of 100 Ω and a full scale range of 50 µ A. It can be used as a voltmeter
or as a higher range ammeter provided a resistance is added to it. Pick the correct range and resistance
combination(s).
(A) 50 V range with 10 K Ω resistance in series
(B) 10 V range with 200 K Ω resistance in series
(C) 5 mA range with 1 Ω resistance in parallel
(D) 10 mA range with 1 Ω resistance in parallel.

F.13 In the circuit shown the readings of ammeter and voltmeter are 4A
and 20V respectively. The meters are non-ideal, then R is
(A) 5 Ω (B) less than 5Ω
(C) greater than 5Ω (D) between 4Ω and 5Ω.

F.14 In the fig. the potentiometer wire AB of length L & resistance 9

r is joined to the cell D of e.m.f. ε & internal resistance r. The
cell C's e.m.f. is ε/2 and its internal resistance is 2 r.
The galvanometer G will show no deflection when the length AJ is:
(A) 4L/9 (B) 5L/9
(C) 7L/18 (D) 11L/18

F.15 In the circuit shown in figure reading of voltmeter is V1 when only

S1 is closed, reading of voltmeter is V2 when only S2 is closed and
reading of voltmeter is V3 when both S1 and S2 are closed. Then
(A) V3 > V2 > V1 (B) V2 > V1 > V3
(C) V3 > V1 > V2 (D) V1 > V2 > V3

F.16 In the given circuit the ammeter A1 and A2 are ideal and the ammeter
A3 has a resistance of 1.9 x 10 -3 Ω. Find the readings of all three
meters.

F.17 In a potentiometer circuit, two wires of same material of resistivity ρ, one of required radius of
cross-section ' a ' and other of radius of cross-section ' 2 a ' are joined in series. They are of length and 2
respectively. This combination acts as the potentiometer wire of length 3 . The emf of the cell in the primary
ρλ
circuit is ε and internal resistance is . This cell is connected to the potentiometer wire by a conducting
2πa 2
wire of negligible resistance with positive terminal of the cell connected to one end (call it A) of longer wire.
The negative terminal of the cell is connected to one and of the smaller wire. The remaining ends of the two

Page # 12
 wires are joined togethor. Find:
(i) The maximum voltage which can be balanced on the potentiometer wire.
ε
(ii) The balancing length, measured from point A, obtained in measurement of emf of cell of emf .
2
ε ρλ
(iii) If positive terminal of cell of emf and internal resistance is connected to point A and other
2 2πa 2
terminal is joined to the junction of the two wires, then find the current through this cell.

ONE OR MORE THAN ONE CORRECT

1. Electrons are emitted by a hot filament and are accelerated by an electric field as shown in fig. The two stops
at the left ensure that the electron beam has a uniform cross-section.

(A) The speed of the electron is more at B than at A.

(B) The electric current is from left to right
(C) The magnitude of the current is larger at B than at A.
(D) The current density is more at B than at A.
2. A current passes through a wire of nonuniform cross-section. Which of the following quantities are indepen-
dent of the cross-section?
(A) the charge crossing in a given time interval (B) drift speed
(C) current density (D) free-electron density.
3. The conductivity current density in a wire is 10 A/cm2 and the electric field in the wire is 5 V/cm. If ρ =
resistivity of material, σ = of the material then (in S.Ι. units):
(A) ρ = 5 x 10 −3 (B) ρ = 200 (C) σ = 5 x 10 −3 (D) σ = 200
4. A bulb is connected to a battery of emf 10 V so that the resulting current is 10 mA. When the bulb is
connected to 220 V mains, the current is 50 mA. Choose the correct alternative (s)
(A) In the first case, the resistance of the bulb is 1kΩ and in second case, it is 4.4 kΩ.
(B) It is not possible since ohm’s law is not followed
(C) the increase in resistance is due to heating of the filament of the bulb when it is connected to 220 V mains
(D) None of these
5. Choose the correct alternatives
(A) It is easier to start a car engine on a warm day than on a chilly cold day because the internal resistance
of battery decreases with rise in temperature
(B) It is more economical to transmit electric power at high voltage and low current rather than at low voltage
and high current because heat loss is proportional to square of current.
(C) The heating coil of an electric iron is enclosed in mica sheets because mica is a bad conductor of heat
and good conductor of electricity
(D) The heating coil of an electric iron is enclosed in mica sheets because mica is a good conductor of heat
and bad conductor of electricity.
6. In a potentiometer wire experiment the emf of a battery in the primary circuit is 20volt and its internal
resistance is 5Ω. There is a resistance box (in series with the battery and the potentiometer wire)
whose resistance can be varied from 120Ω to 170Ω. Resistance of the potentiometer wire is 75Ω. The
following potential differences can be measured using this potentiometer
(A) 5V (B) 6V (C) 7V (D) 8V
7. By mistake, a voltmeter is placed in series and an ammeter is parallel with a resistance in an electric circuit,
with a cell in series.

(A) If the devices are ideal, ammeter will read zero current and voltmeter will read the emf of cell
B) If the devices are ideal, a large current will flow through the ammeter and it will be damaged
(C) The main current in the circuit will be very low and practically all current will flow through the ammeter, if
resistance of ammeter is much smaller than the resistance in parallel.
(D) The devices may get damaged if emf of the cell is very high and the meters are nonideal.

Page # 13
Exercise - 1 SECTION : (D)
SECTION (A) : D.1 (a) R = 10 Ω (b) 1A in each (c) V3 = 3V, V2
A.1 6.25 × 1018 electrons/second. = 2V, V4 = 4V (d) 10 W (e) 1 W (f) 9W
A.2 1.1 × 10 –3 ms –1 or 1.1 mm s–1 (g) 9V (h) 4 Ω resistance (i) 3 W.
A.3 300 C, 30 A 1 1
A.4 0.074 mm/s D.2 (a) R = 3 (b) i = 2A, i1 = A i2 = 1A i3 = A
2 2
A.5 3.2 × 104 s ≈ 8.9 hours.
(c) V = 4V in each (d) 12 W (e) 4W (f) 8 W
A.6 C A.7 C A.8 B
(g) 4Ω (h) 4W
SECTION (B) :
B.1 3.6 A B.2 0.0065 Ω B.3 249ºC D.3 90 watt.
B.4 0.6 km. B.5 A B.6 A D.4 1.6 A, 4.0 A.
B.7 D B.8 B B.9 C D.5 0.15 A, 0.83 A
B.10 B B.11 AC D.6 4 mA in 20 kΩ resistor, 8 mA in 10 kΩ resistor and
B.12 (a) J0 A/3 (b) 2 J0 A/3 12 mA in 100 kΩ resistor, 1340 V
D.7 25 Ω
( K −1) 2 K  (K − 1)  V0 D.8 4 watt.
B.13 (i) ; (ii)  
K (K − 1)  K 2  R3 D.9 (a) 0.1 A (b) 0.3 A
D.10 (i) RAB = 5/6 Ω (ii) RCD = 1.5 Ω
15 U
B.14 2 Ω B.15 Ι= (iii) REF = 1.5 Ω (iv) RAF = 5/6 Ω
7 R (v) RAC = 4/3 Ω
3r D.11 1.5 A
( 2 + π)ar
B.16 B.17
8 5 D.12 (i) 21.43 V, (ii) 1600 Ω
SECTION (C) : D.13 i1 = 1.40 amp. , i2 = 1.66 amp. , i 3 = 1.94 amp.
D.14 31.25 watt.
C.1 (a) E = 10 V each D.15 Rf = 2Ω.
(b) (A) act as a source and (B) act as load D.16 0.3 Ω
(c) VA = 9V, VB = 11 V D.17 B D.18 (a) B (b) C
(d) PA = 9 W, PB = 11 W D.19 C D.20 B D.21 (a) C (b) A
(e) Heat rate = 1 W each D.22 A D.23 A D.24 D
(f) 10 watt.
D.25 A D.26 A
(g) 9V, 11V (h) 9W, 11 W
SECTION (E) :
C.2 (a) rightward (b) all tie (c) b, then a and c tie (d) a, E.1 1.4 A, 11.9 V
then c and b tie. E.2 (i) 0.5 A (ii) 0.0833 A (iii) 1.7 V
C.3 1 A, 0.4 A , 0.6 A E.3 One
E.4 2 rows of cells, each containing 12 cells in
C.4 1 volt series must be connected in parallel
C.5 (a) 7.5 V, (b) 24 mA (c) greater than 12 V. E.5 C E.6 B E.7 D E.8 C
C.6 0.6 Ω 2mn
C.7 zero E.9 D E.10 Ι
m 2 + n2
C.8 (a) VA = VB = VC = VD = 0 V, VE = 10 V = VF = VG =
VH VΙ = 15 V, VJ = 15 V, VK = 15 V E.11 (i) 2 volt (ii) 2 amp.
(b) V1 = 15 V, V2 = 5V, V3 = 15 V 2
(c) each act as a source E.12 (i) volt. (ii) 1.46V
13
(d) 17.5 A (↑), 15A(↓) 2.5 A (↑), 5A (↓) from left to
SECTION (F)
right in given circuit.
(e) 1 Ω resistance F.1 R = 0.015 Ω in parallel ; R = 0.985 Ω in series.
(f) left most battery.
C.9 (a) 4.55 A (b) 48.4 Ω
(c) 1000 W (d) 240 cal s-1
(e) 80/3 gm F.2 (a) S = 0.2013 Ω (b) R

C.10 90% C.11 D C.12 D

C.13 A C.14 B C.15 B
C.16 B C.17 ABC C.18 ABD = 70 Ω

Page # 14
F.3 290 kΩ , Due to very small value of current,
Ammeter has not been used. The ammeter
reading would have been very small. Note that
this is unusual use of a voltmeter. It is meant
only for the measurement of high registance.
F.4 (a) 24 V, (b) 28 V
F.5 0.125 A.
F.6 (a) 1.25 V
(b) The high resistance to keep the initial
current low when null point is being located.
This saves the standard cell from damage.
(c) This high resistance does not affect the
balance point because then there is no flow of
current through the standard cell branch.
(d) The internal resistance of driver cell affects
the current through the potentiometer wire.
Since potential gradient is changed, therefore,
the balance point must be affected.
(e) No. It is necessary that the emf of the driver
cell is more than the emf of the cells.
(f) This circuit will not work well for meaurement
of small emf. (mV) because the balanced point
will be very near to end A, and percentage error
in EMF measured due to length measument
V dE
would be very large E = ⇒
100 E
dλ
= will be large if is very small.
λ
F.7 6.86 Ω , 13.5 Ω
F.8 4 Ω.

F.8 (i)

(ii) 200 Ω (iii) 0.23 V

F.9 C
F.10 A F.11 C
F.12 BC F.13 C
F.14 B F.15 B
F.16 Ι1 = 82/27, Ι2 = 34/27, Ι3 = 0
3ε 5λ
F.17 (i) v0 = (ii)
4 2
ε ρλ
(iii) , where R = and A = 2πa2
7R A
ONE OR MORE THAN ONE CORRECT
1. CD 2. AD 3. AD
4. AC 5. ABD 6. ABC
7. ACD

Page # 15