84 52 65C
84 52 65C
NOTE: If an operator has already procured the ModKit for this service
bulletin and has not installed the kit, parts of the Modkit may be used
to accomplish the Service Bulletin 84-52-73 by procuring only
necessary kits as described in SB 84-52-73.
NOTE: No action is required for operators who have already installed this
service bulletin.
1. PLANNING INFORMATION
A. Effectivity
Aircraft Affected:
In-Service: DHC-8 Aircraft Models 401 and 402 Serial Numbers 4001 thru
4346.
Verification: ModSum 4-190235 has been installed on DHC-8 Aircraft
Model 402 Serial Number 4262.
Removed reference to Production
NOTE: The instructions in this service bulletin are only applicable to the systems
and parts installed at the time of delivery on the aircraft or as changed by
Bombardier Aerospace Service Bulletin(s). Before you do this bulletin,
examine all STC or equivalent action changes to make sure this bulletin
can be completed.
Spares Affected:
None
B. Reason
Problem: Refer to enclosed Shorts Service Bulletin D8400-52-0004.
Solution: This Service Bulletin provides instructions to relocate the door locked
sensor on the aft passenger door and therefore improve the operational
integrity.
C. Description
The procedures in this service bulletin give the instructions to do the tasks that
follow:
- aircraft is put into standard configuration for maintenance
- aircraft electrical power is removed
- the nose landing gear lock is engaged
- the main landing gear lock pins are installed thru each main gear and main gear
door mechanism
- the door locked sensor on the aft passenger door is relocated
- an operational test of the door is done
- close out.
D. Compliance
Installation of ModSum 4-190235 may be done at the operator’s discretion.
E. Approval
The technical content of this service bulletin has been approved under the
authority of the Transport Canada Civil Aviation (TCCA) Design Approval
Organization No: DAO #93-Q-02.
This Service Bulletin does not affect Airworthiness Limitations (AWLs) or Damage
Tolerance Inspections (DTIs).
F. Manpower
It will take an estimated 9 man-hours to complete this service bulletin. The
breakdown of the man-hours is shown in the table that follows:
TASK MAN-HOURS
Job Set-Up 0.25
Procedure 8.00
Test / RTS 0.50
Close-Out 0.25
For any on-site labor assistance, please speak with a Fleet Services representative
for a quote. The Fleet Services group can be contacted via the Q Series Technical
Help Desk by telephone at 416-375-4000 or email at :
[email protected]
Bombardier Aerospace
Customer Accounts Services Team (Mail Stop N11-32)
123 Garratt Blvd.
Toronto
Ontario
Canada M3K-1Y5
K. Publications Affected
Maintenance Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PSM 1-84-2
Dash 8 Illustrated Parts Catalogue . . . . . . . . . . . . . . . . . . . . PSM 1-84-4
Wiring Diagrams Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . PSM 1-84-2W
ModSums Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PSM 1-84-12
L. References
Revision ‘C’ of this service bulletin was prepared to the engineering drawings and
related data that follows:
2. MATERIAL INFORMATION
In addition to the parts in the kit, the following material is required for the
completion of this service bulletin and may be procured as single items from
Bombardier Aerospace Regional Aircraft or purchased directly from industry
sources.
Addresses of manufacturers and suppliers not shown below are listed in either
Maintenance Manual Chapter 20 or in Structural Repair Manual Chapter 51 or, for
400 Series Aircraft, in Consumable Products Manual PSM 1-84-18.
3. ACCOMPLISHMENT INSTRUCTIONS
A. Job Set-Up
(1) Placard and select all aircraft electrical power to OFF. Obey all relevant
WARNINGS and CAUTIONS (refer to AMM TASK’S 24-00-00-861-802 and
24-00-00-910-801).
(2) Make sure that lock pins are installed thru each main gear and main gear door
mechanism.
(3) Make sure the nose gear ground lock is engaged.
(4) Set up the work platforms or ladders as required to gain access to the rear
passenger door. Make sure the work platforms or ladders are electrically
grounded.
B. Procedure
(1) Refer to the enclosed Shorts Service Bulletin D8400-52-0004 and relocate the
door locked sensor on the aft passenger door.
C. Close Out
(1) Remove all tools and equipment from the work area.
(2) On incorporation of this ModSum, make an entry that conforms to local
regulatory requirements in the applicable logbook(s). Enter component serial
numbers if applicable. Enter this ModSum number only after complete and
functional incorporation of all work defined in this service bulletin.
From:
Company:
Phone: Extn:
Facsimile: Date:
E-- mail:
The data that you provide below will help us record the incorporation of this ModSum
and the aircraft effectivity in the maintenance manual.
Fax this sheet to (1) 416 375 4538 or Email PDF to:
[email protected] Jan 2009
SERVICE BULLETIN (SB) --- COMMENT SHEET --- Q SERIES DASH 8 AIRCRAFT
To: SB Focal (Toronto), Bombardier Aerospace Commercial Aircraft
Phone: (1) 416 375 4078 Facsimile: (1) 416 375 4538
E-- mail: [email protected]
From:
Company:
Phone: Extn:
Facsimile: Date:
E-- mail:
Select appropriate box(es) and add comments or suggestions you would like us to know
that may enhance the quality of our service bulletins.
Service Bulletin: Revision: ModSum:
1. PLANNING INFORMATION
V Effectivity V Reason V Description V Compliance
V Approval V Manpower V Material V Weight and Balance
V Electrical Load V Tooling V References V Publications Affected
2. MATERIAL INFORMATION
V Kit Content V Special Tools/Equipment V Parts to Modify Spares
V Consumables V Disposition of Existing Parts V Other
3. ACCOMPLISHMENT INSTRUCTIONS
V Job Set---Up V Procedure V Close---Out V Test
V Illustration(s) V Other
Fax this sheet to (1) 416 375 4538 or Email PDF to:
[email protected] Feb 2009