Scribd
Upload
19 views

How To Configure An SSH Tunnel On Putty

Uploaded by

fitra.natan
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
19 views

How To Configure An SSH Tunnel On Putty

Uploaded by

fitra.natan
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 7

How to Configure an SSH Tunnel on PuTTY

Most of you have probably used a tunnel with an SSH


connection. What you probably weren’t aware of is
YOU CAN USE A DYNAMIC that you can use a dynamic tunnel to access all remote
TUNNEL TO ACCESS infrastructure. Furthermore, you can specify a port and a
ALL REMOTE destination IP to have direct access. This process is achieved

INFRASTRUCTURE. through your PuTTY configuration.

In this procedure, we will use Internet Explorer, Firefox


and an RDP connection to demonstrate the use of a
tunnel with an SSH connection, as well as configuring the
tunnel with several other protocol types.
LOCAL PORT FORWARDING

STEP 1 – Load the Session

In your PuTTY configuration, configure the Host Name


and Port of your remote SSH computer­. Enter your Saved
Sessions name, and click Save. If your session already
exists, Load it as shown below:

STEP 2 – Configure PuTTY for RDP

In the Tunnels section in PuTTY, configure a specific Local


port, such as 50001, that will redirect to 3389 of your
destination server.

In the Source Port field, enter the local port that will be
redirected. In the Destination field, enter the IP address
as well as the destination port. Select Local and Auto to
activate IPv4 and IPv6. Here is an example from my local
machine I would like to go to 172.128.123.10, server port
3389.

2
Please note that you may configure your ports for multiple
servers simultaneously. Configuring a specific Local port such
as 50002 will redirect to 80 of your destination server. Doing
so will allow you to configure PuTTY to your web browser.

Once the configuration setup is complete, open an RDP


connection and enter your local IP (127.0.0.1), along with the
local port configuration in PuTTY.

As illustrated above, if I enter 127.0.0.1:50001, my connection


will translate to the server 172.128.123.10:3389.

If I enter 127.0.0.1:50003, my connection will translate to the


server 172.128.123.11:3389.

STEP 3 – Configure the SSH Tunnel

In the Category menu, drill down to Connection --> SSH --> Tunnels. There are several ways to configure a Tunnel. We shall
proceed with a browser tunnel configuration.

3
ADVANCED SCENARIO (DYNAMIC PORT FORWARDING)

STEP 4 – Configure PuTTY for a Web


Browser Tunnel

At the Tunnels page, configure a Dynamic port between


the ranges of 49152-65535. For additional information,
refer to https://en.wikipedia.org/wiki/List_of_TCP_and_UDP_
port_numbers 49152–65535.

STEP 5 – Configure Your Software

Further information for Internet Explorer, Chrome or Edge can be seen in Step 5.1. For Firefox, refer to Step 5.2, and for RDP
usage, refer to Step 2.

STEP 5.1 – Configure Internet


Explorer to Pass Through
an SSH Tunnel
As previously noted, configuring a tunnel through Internet
Explorer will affect Google Chrome and Microsoft Edge.

1- Click on Internet options by navigating through your


Control Panel in your Internet Explorer browser.

4
2- The following illustration displays the Control 4- Check the Use a proxy server for your LAN box, and
Panel Home. click Advanced.

3- Select the Connections tab and click on LAN settings.

5- Enter 127.0.0.1 of the host IP in the Socks field, with the


configured Port of 4567, and click OK.

5
You should see a grey Address bar. If your remote segment
IP differs from internal segment, please check the Bypass
proxy server for local addresses box.

Once complete, you will be able to access Internet Explorer, Edge or Chrome to navigate onto an IIS server by entering the IP in
your navigator. You may open a browser tab and visit http://172.128.123.10 in this example. Doing so will allow you to view the
service from the Destination server.

YOUR CONFIGURATION SHOULD LOOK LIKE THE FOLLOWING FIGURE.

6
STEP 5.2 – Configure your Firefox
Browser

1- In your Firefox browser, click on the Menu button in the


top-right corner of the screen, and select Options. Then,
navigate to the Advanced tab.

2- Within the Advanced tab, select the Network tab and click
on Settings in the Connection section.

Once complete, you will be able to access Internet Explorer, Edge or Chrome to navigate onto an IIS server, by
entering the IP in your navigator. You may open a browser tab and visit http://172.128.123.10 in this example. Doing
so will allow you to view the service from the Destination server.

You might also like