Orthopaedic Research

Laboratory

LAB
ORIENTATION
MANUAL
by Shane Curtiss

Updated 1/06
 BASIC LABORATORY SAFETY
RULES
• NO EATING OR DRINKING IS ALLOWED IN THE
LAB AREAS
• NO OPEN TOE OR OPEN HEEL SHOES ARE
ALLOWED IN THE LAB AREAS
• PROTECTIVE GLOVES AND APPROPRIATE
PERSONAL PROTECTIVE EQUIPMENT ARE
REQUIRED WHEN HANDLING SPECIMENS AND
CHEMICALS
• NO GLOVES ARE ALLOWED IN THE
ADMINISTRATIVE AREAS
 BASIC PRINCIPLES OF
LABORATORY SAFETY
• Know your procedure
• Know your chemicals
• Reduce exposure potential
Substitute less hazardous materials
Use smaller quantities
Use a fume hood when needed
Reduce splash hazard
• Wear protective equipment
• Use common sense
 Student/Employees
Students who are also employees will be subject to the same risk assessment and
enrollment criteria as other employees. Some students, by virtue of
volunteering in laboratories, participating in 199 classes, or conducting
individual research projects, may be exposed to increased risk equal to that of
employees. Such students will be required to enroll in the Occupational
Health Program. In all cases, the decision to enroll or not to enroll will be
based on risk assessment of the work rather than on the employment status of
the worker.
A major health and safety concern in this lab is protection while working with
human/animal tissues. Therefore, nitrile gloves, lab coats or surgical gowns,
masks and shoe covers are provided for your use and are located in Room
2106. Please use these safety precautions when handling specimens.
WHENEVER YOU SUSTAIN AN INJURY, REPORT IT USING THE
ACCIDENT REPORT ONLINE AT:
http://safetyservices.ucdavis.edu/programs-and-services/injury-
illness-prevention-iipp/injury-illness-prevention-program-iipp-1
 EH&S classes
The UC Davis EH&S website http://safetyservices.ucdavis.edu/ or the UCDMC EH&S
website http://www.ucdmc.ucdavis.edu/medresearch/medsp/labsafety.html are the primary
resources for safety information

You can find and enroll in most all classes through the EH&S website
http://safetyservices.ucdavis.edu/training/environmental-health-safety-and-emergency-
management-training

ANIMAL CARE & USE 101

Learn about the laws and regulations relating to the use and care of animals in research and
teaching. Since the USDA requires that anyone working with animals be familiar with the
regulations covering their use, attendance to this seminar is required by anyone working with
animals in a teaching or research capacity. To enroll in this course and to view posted schedules
go to Learning Systems Website listed above.
LABORATORY ANIMAL SKILLS
The Office of the Campus Veterinarian regularly offers Laboratory Animal Skills classes.
The classes cover husbandry, handling, restraint, injection and bleeding techniques of the
various species of laboratory animals including mice, rodents and rabbits. Most of these
classes are open to any interested animal care staff or student workers and are free of
charge to UC Davis employees. You must attend the Animal Care and Use 101 class listed
above before you can sign up for Lab Animal Skills classes.

BIOLOGICAL SAFETY & MEDICAL WASTE MANAGEMENT

This course is required for anyone who handles human blood or body fluids or who generates medical
waste.
 More EH&S classes
CHEMICAL/LABORATORY SAFETY
This class satisfies initial awareness training specified by the laboratory safety standard for personnel
working in laboratories that use chemicals. This class is also appropriate for workers new to chemical
laboratory work and as a refresher for those who are returning to laboratory work or who want to brush up
their skills.

HAZARDOUS WASTE MANAGEMENT AND MINIMIZATION

This class is required for anyone who will be using chemicals or generating hazardous or chemical waste.

ANALYTICAL X-RAY SAFETY

This class is specifically tailored for people who will work with analytical X-ray units (faxitron cabinets) .
Completion of this class, along with the online Diagnostic X-Ray Safety class is required in order to be added
to lab MUA and to be able to receive lab training to operate X-Ray machines in the lab.

LABORATORY RADIATION SAFETY

This class discusses sources of ionizing, radiation exposure limits, risk evaluation and safety precautions.
Demonstrations of good health physics practices are stressed. This class is required for anyone using
radioactive isotopes in the lab. Completion of this class along is required to be added to the lab RUA and
receive training in radioactive isotope use.
 FIRE PLAN Intro
The Fire plan is to be used by the staff of SOM Research I to protect themselves and
visitors from fire emergencies. It is part of a larger disaster plan for the Medical
Center, which addresses all perils that could befall the facility.

The SOM Research I Fire plan consists of two essential elements, both of which must
be present for it to succeed:

1. Written guidelines and posted information -

The plan contains general information applicable to the
building, as well as specific guidelines and a floor plan
for the building. Fire evacuation signs are designed to
complement the plan.

Familiarization -
Being familiar with the locations of doors and windows and
how they unlock is essential to the success of this plan. Know
where the doors are…know how the locking mechanisms
work. You should be able to find an exit in the dark!
 FIRE PLAN
If a fire occurs, you should know the R.A.C.E. procedure:
This consists of Rescue, Alarm, Confine, Extinguish

RESCUE: Rescue anyone (this includes yourself) who is in immediate

danger from the fire. Remove these people to the closest safe area,
simultaneously notifying other staff of the fire and its location. Know
where the alternate exits are located.
ALARM: If you are the first person to discover a fire, alert the people in the area
so that you can take proper action together. Immediately pull a fire alarm
manual pull station and call 9-1-1 from the nearest safe location. If you are
involved in a rescue, send someone to pull a manual fire alarm pull station and
call 9-1-1.
CONFINE : Confine the fire by closing all of the doors in and around
the fire area. This will keep fire and smoke out of the exit way
during evacuation. The doors are programmed to
automatically shut and lock when the alarm goes off. Please do not try to get
back into the rooms when they are closed.
EXTINGUISH: There is no better time to control and extinguish a fire than in its
early stage. Utilize fire extinguishers if you discover a fire in its earliest stage. If
a fire is well developed, however, the best thing to do is to get out safely. Do not
place yourself at unnecessary risk.
FIRE PLAN EVACUATION
If a fire occurs, all personnel will evacuate the building
immediately. Use the nearest safe exit. Do not use the elevator.
Staff using the rear (east) exit should be alert for vehicular
traffic, particularly fire vehicles using the driveway to access fire
hydrants and fire sprinkler connections. After evacuation,
everyone will assemble in the parking lot in the front (west side)
of the building.

 Account for all employees and report to Matthew Anderson or

Blaine Christiansen. Missing persons should be reported to
responding emergency personnel.
 FIRE PROTECTION COMPONENTS
Building 97 has been designed with specific features that will impede the spread of fire. It
is important that you understand these features so that you (1) effectively use these fire
protection components during an actual fire, and (2) don't inadvertently neutralize or
override the components as you carry out your daily duties.
Building construction and related passive fire protection features
This building is constructed of noncombustible structural materials, principally concrete
and steel. Each floor is constructed with fire-rated (fire resistant) walls, floors and corridors
in such a way that the building is compartmentalized. This is the passive method of fire
protection designed to keep the fire from spreading throughout the building.
Fire sprinkler systems
Fire sprinklers are designed to open when exposed to heat (not smoke) from a nearby fire.
These systems are the most effective means of stopping a fire from spreading throughout a
building. The Research Laboratory is protected by an automatic sprinkler fire system with
sprinkler heads in every room.
Fire alarm system
There is a complete fire alarm system in this building. Pull the fire alarm manual pull
station and dial 911 to report any fire, even if the fire is immediately contained. Dial 911
from a safe location, and do so as soon as possible. There are pull stations at the end of each
exit corridor. If you use a pull station, be sure that you or someone else calls 911 as well.
Fire extinguishers
Class ABC fire extinguishers are provided in the building for your use. Class ABC fire
extinguishers are for use on fires involving ordinary combustible materials (wood, paper,
plastic and textiles), flammable liquids, and energized electrical equipment. Be sure that
you know where the fire extinguishers are located and how to operate them.
 If you are injured in the lab
If you sustain an injury/illness while working in the lab, REPORT
the incident IMMEDIATELY to your supervisor.
The supervisor will arrange for you to get appropriate medical care or provide
first aid treatment.

Even if the injury seems minor, it should be reported. There is a injury report
form in each lab area. The slightest cut with a scalpel or even a paper cut should
be reported.

An employee claim form MUST be provided to the employee within ONE

working day if the injury/illness results in:
*medical treatment beyond first aid,
*lost time beyond the day of injury,
*the request of an Employee Claim Form.
As is required by law, your supervisor will give you the Employee Claim Form. If
there are questions, the Workers Comp can be contacted at 734-6180.
FIRST AID: Electrical Burns
1. Make sure that the electrical power is turned off
before attempting to assist the victim.
2. Remove the victim from any potential threat of
fire.
3. If the victim is pulse less, CALL 911!
CPR SHOULD BE ADMINISTERED
4. If the victim has signs of life, conscious or
unconscious, place victim in shock position
(feet elevated above heart) and seek prompt
medical attention.
Most damage from electrical burns is internal and
should be treated at the hospital.
 FIRST AID: Chemical Burns
Chemical burns of the skin and eyes are caused by caustic chemicals such as strong
acids, alkalis and other caustic agents.
Skin
1. Remove any contaminated clothing from the burn area.
2. Flush affected area with copious amounts of water at least 15 minutes. If a large
body surface area is affected, use the emergency shower located in the hallway.
If burns are caused by strong acid, neutralize with bicarbonate of soda.
If burns are caused by dry lime, brush off powder and flush with phenol.
DO NOT USE WATER IN THESE CASES!
3. Cover the affected area with a dry sterile dressing.
4. Observe for signs of shock and seek medical help.
Eyes
1. Flush the eye(s) with eyelids open for a minimum of 20 minutes with large
volumes of water. Eyewash stations are in each hallway. Use them!
2. Bandage the affected eye with a moist, sterile dressing, then cover both eyes.
3. Observe for signs of shock and seek medical help.

IN ALL CASES, TRY TO IDENTIFY THE CHEMICAL INVOLVED,

BUT ONLY AFTER VICTIM HAS BEEN TREATED!!!!!
FIRST AID: Thermal Burns
Thermal Burns: Burns of the skin and/or eyes caused by heat, fire
or explosion.

1) Remove victim from the source of the heat and observe the
type of burn involved:

a) 1st degree = skin reddened

b) 2nd degree = skin reddened with blister formation
c) 3rd degree = skin is charred

2) 1st degree - Rinse with cool water.

2nd degree and 3rd degree - Cool with sterile water or saline
while covered with a sterile sheet or towel. Remove clothing
from around the burn site, but not clothing that has been
burned into the site. Do not use any kind of ointment on the
burn and do not rupture any blisters.
Treat for shock for 2nd and 3rd degree burns.
Call 911!
 FIRST AID: Poisoning
Inhalation Poisoning
1) Remove the victim from the source of the chemical.
2) Observe the victim for spontaneous respiration. If none is observed, have
someone call 911 for medical assistance and start artificial respiration:
a) Tilt victim’s head back to open airway.
b) Look and listen for respiration. If none continue.
c) Pinch nostrils closed and breath four full breaths of air into the victim’s
mouth. Observe for respiration.
d) Breath into the victim’s mouth once every 5 seconds until the victim
breaths spontaneously or until medical assistance arrives.
3) When the victim is breathing spontaneously, insure adequate ventilation
with oxygen or fresh air.
Ingestion Poisoning
1) Look for any identification of the chemical involved and read the label for any
specific antidote (check Material Safety Data Sheets). Have someone call the
POISON CONTROL CENTER AT 9-1-800-876-4766 or call 911 !
2) Note if the victim is conscious or unconscious. If unconscious then start
artificial respiration and/or CPR.
General rule - Induce vomiting ASAP by using the gag reflex and/or administering some type of
emetic such as Syrup of Ipecac or Saltwater. Exceptions are when the victim has acid or caustic
burns around their mouth or has a petroleum breath odor. In these cases DO NOT INDUCE
VOMITING - DILUTE WITH WATER OR MILK ! Do not attempt to neutralize unless
specified by the poison control center.
FIRST AID: Eye Injuries
May be caused by shrapnel from
milling, grinding or drilling equipment.
1) Pull upper eyelid down over the eye to the lower
eyelid to dislodge any particle from the cornea. Repeat
if necessary. If the object can be seen, it may be able to
be removed by using a piece of tissue paper.
2) If this doesn’t work, try washing out the eye with
saline or water from one of the many eyewash stations
in the lab.
3) If this still doesn’t work, bandage both eyes and
have the patient transported to the hospital emergency
room for a more thorough examination.
4) If an object has been impaled into the orbit, seek
medical attention at once. Call 911 ! Do not attempt to
remove the impaled object. Bandage both eyes and
treat for shock.
Miscellaneous Injuries
Bleeding
1) Control hemorrhage from injuries such as deep cuts and
avulsions by applying direct pressure to the injury site with any
type of absorbent cloth material.
If the bleeding is severe call 911 !
2) Continue to apply fresh cloth or gauze as needed to control the
hemorrhaging without removing any previously applied material.
Be sure to evaluate the injury site if possible.
3) If direct pressure and elevation above the heart doesn’t control
the bleeding, apply pressure to the pressure point proximal to the
injury site. Apply a tourniquet only as a last resort and only when
a decision between life or limb exists.
4) Place the victim in shock position with their legs elevated above
their heart and kept warm.
5) In the case of amputation, a tourniquet may be required.
Additionally, place any avulsed pieces/parts in saline in a freezer
bag and label it for material testing or transport to the hospital with
the victim.
Miscellaneous Injuries
Heart Attacks and Strokes

1) Seek medical attention at once.

Call 911 !

2) Start CPR.
3) In the case of a stroke, insure that the
victim has an adequate airway. Keep the
victim calm and treat for shock.
Miscellaneous Injuries
Shock
1) Signs of shock are:
a) Pale with cool and clammy skin.
b) Varying degrees of sweating.
c) An increased respiration rate as the blood pressure
drops and the pulse rises.
CALL 911
2) Place the victim lying down on their back with their legs
and feet raised 6-8 inches above the ground.
3) Place a blanket over the victim to keep them warm. Also
place a blanket under them to decrease the conduction heat
loss into the ground.
4) Do not give anything by mouth to a person with a severe
abdominal injury, or to a person who has no gag reflex or to an
unconscious person.
 Human Tissue Handling
Speak to Safety Coordinator about precautions and equipment before
commencing work for the first time.

2) Always wear gloves, protective clothing and face mask. Remove your gloves
before touching anything other than your contaminated tools or specimens.
Remove them before answering the phone, opening the door, operating a
computer keyboard, opening a drawer, turning on a light, etc., etc. If you use a
pen or pencil with contaminated gloves on, it must be decontaminated; it is
expensive to dispose of contaminated waste and it can not be left as a hazard for
other workers.
3) Hepatitis B Vaccination is required. Talk to the Lab Coordinator about
getting the vaccination series.
4) All Tissue that is brought into this lab has been screened and test non-reactive
for Hepatitis and HIV. However, treat all human tissue as though it contains a
transmissible virus.
5) Dispose of all human tissue into the waste freezer, rm. 2210 with ID tag.
6) Dispose of all paper and dirty gloves into one of the red biological waste
cans.
7) Dispose of any sharp objects into a Sharps container (located in every room).
Dispose of the Sharps container when it is 2/3 full by sealing it, writing the date
and room number on it then place it in a red biological waste can.
 Specimen Exposure
Students whose only exposure to animals or cadaveric specimens will be participation in a
teaching exercise will not normally be required to enroll in the Occupational Health
Program, but they should be provided with information about any health considerations
relative to the specimen with which they will be working.
All specimens received by ORL test non-reactive for HIV, Hepatitis B and C. However,
treat all human tissue as if it contains a transmissible virus.
Always wear gloves and a gown or lab coat when handling cadaveric specimens.
All specimens must be placed in a secondary container when transporting them.
Make sure specimen is identified with an ID tag at all times containing the following info:
Specimen ID# assigned by donated body program
Name of Principle Investigator
Description of specimen including species -ex. human rt. lower limb
Date last used
THERE IS ABSOLUTELY NO HUMAN TISSUE ALLOWED IN THE WASTE CANS!
Dispose of all human tissue into the waste freezer (Rm 2210) and mark “waste” on tag
Dispose of all paper and soiled gloves into Red Biological Waste cans.
Dispose of any sharp object into sharps container (in every room).
Dispose of Sharps container when 2/3 full into Red Biohazard Waste container.
DO NOT REMOVE TISSUE FROM ORL. PERIOD!
 Disposal of Cadaveric Waste
CADAVERIC SPECIMENS
Cadaveric waste is classed with blood borne pathogen waste
material. Place cadaveric waste in a plastic bags with ID tag.
Write date / specimen ID # and description / PI name / and
“waste”on tag.Place in Human Waste Freezer (Rm. 2210).
When freezer is full, the mortuary service will be contacted.
BLOOD AND BODY FLUIDS
Non-infectious blood and body fluids in tubes, bags,
vacutainers, etc.
Treat with bleach (10% final volume) and pour into a sink
drain connected to the campus sewage system. DO NOT pour
into a storm drain. DO NOT dispose of containers of liquids in
garbage cans, dumpsters or red biohazard cans.
Non-infectious blood or fluid soaked materials
Place bandages, gauze, paper towels, etc. in the red
biohazard bags. There should be no dripping or leakage of
liquid from bagged waste.
 Needle and Sharps Disposal
Sharps waste is composed of instruments used to puncture, cut, or scrape body
parts, that when disposed of can cause punctures or cuts. DO NOT throw sharps
containers or sharps directly into garbage cans or dumpsters.

NEEDLES AND SYRINGES

Containing nonhazardous substances
Place into a hardwalled sharps container (non-red without biohazard
label). When 2/3 full, seal the container, mark it with the date and
room number and place the sharps container in red biohazard trash
bin.
Containing biohazardous materials (blood etc)
Place into a hardwalled sharps container (red with biohazard label).
When 2/3 full, seal the container, mark it with the date and room
number and place the sharps container in red biohazard trash bin.
Containing chemical carcinogens
Place into a hardwalled sharps container. Label with a hazardous
waste label, and contact EH&S for pick-up as a hazardous chemical
waste (4-7324).
Containing radioactive materials
Place into a hardwalled sharps container (non-red without biohazard
label). Label with radioactive tape, and place full sealed container in
a dry radioactive waste box. Contact EH&S for pick-up as
radioactive waste (4-3355).
 GLASS DISPOSAL
LABORATORY GLASS
Any item that could puncture regular waste bags and endanger waste handlers. DO
NOT pick up broken glass with your hands, if possible. Wear cut-resistance gloves
and use a broom. Collect broken glass as carefully and completely as possible.
Contaminated with nonhazardous substances
Place clean glass and triple rinsed glass bottles into the lined
cardboard glass container or glass waste can in rm 2110.
Custodial staff will dispose as nonhazardous waste. Call Env.
Svcs 4-2855 for pickup.
Contaminated with biohazardous agent (blood etc)
Place into a hardwalled sharps container (red with biohazard
label). Seal and label with room number and building and place in
red biohazard can.
Contaminated with toxic or hazardous chemicals
Place into a hardwalled sharps container (non-red without
biohazard label). Label with a hazardous waste label, and contact
EH&S for pick-up as a hazardous chemical waste.
Contaminated with radioactive waste
Place into a hardwalled sharps container (non-red without
biohazard label). Label with radioactive tape, and place full sealed
container in a dry radioactive waste box.
Contact EH&S for pick-up as radioactive waste.
 General Chemical Safety
Proper chemical storage is essential in assuring a safe work environment for
students, staff, faculty, and visitors. These guidelines will help you store chemicals
safely in your work place.
Inventory
Federal, state and local regulations require that the campus
maintain chemical inventories. ORL does an internal audit of all
chemicals every year, so please keep track of the chemicals if you
order them.
Labeling
All chemical containers must be clearly labeled. These labels should
include the chemical name, chemical manufacturer, major hazard(s), and
date received and/or prepared.
Storage
Chemicals should be stored according to compatibility and hazard
classification. Storage areas must be clearly labeled. Laboratories must
establish separate storage areas for each of the following:
Flammable and combustible organic solvents.
Corrosive inorganic acids.
Dry poisons, dry salts and dry oxidizers.
Corrosive bases.
Corrosive organic acids such as acetic acid.
CHECK YOUR LAB AREA FOR THE STORAGE
LOCATION OF CHEMICALS!!!
Chemical Safety Guidelines
– Know the location of all Eyewash/
Shower stations and fire extinguishers:
– Eyewash/Shower Locations
• Hall alcove outside Rm. 2101
• Hallway outside Rm. 2108
• Room 2206
• Hall outside 2212
Fire Extinguisher Locations (in Hall)
Room 2002
Room 2111
Room 2202
 CHEMICAL SAFETY/ MSDS
Locations: Material Safety Data Sheets are located in each laboratory
area where chemicals are stored. You are responsible to know the
chemicals you are working with. All MSDS are available online.
Locations:
Room 2107- Above the sink (3 binders)
Room 2109- Histology Desk
Room 2208- Bookshelf above desk
Room 2204 (Electronics Room)- Bookshelf above bench
If you intend to work with a specific chemical, read the MSDS. Knowing
the properties of your chemicals will make a safer environment.
For more information about safety, access the Environmental Health and
Safety website. http://ehs.ucdavis.edu/chem/chem_links.cfm or
http://www.tomescps.com/ Disclaimer.asp for chemical lookup.
Disposal of Chemical Waste
All hazardous chemical waste must be picked up by Environmental Health
and Safety (EH&S) technicians (4-7324)

Empty chemical containers may be disposed of as ordinary laboratory

trash if the chemical is not classified as an extremely hazardous material,
each container is triple-rinsed, allowed to air dry, all labels are defaced,
and the cap removed. Custodians are instructed not to dispose of any
chemical bottles unless the bottles have been properly cleaned. At no
time should full, partially full, or unrinsed containers be thrown in the
trash.

Empty extremely hazardous materials containers should not be triple-

rinsed. These must be disposed of as hazardous waste.

All sharp objects such as needles, syringes, and broken glassware must
be placed in a hard-walled container and labeled with the hazardous waste
label. All fluorescent, metal halide and mercury vapor bulbs are considered
hazardous waste and must be disposed of properly. Please contact
Facilities Services at 4-7324 to arrange pickup of your used light bulbs.

The form used for chemical waste disposal is located in Room 2208.
 FORMALIN USE
Formaldehyde is a colorless, flammable gas with a strong pungent odor that can be detected at less than 0.5 parts per
million (ppm). The aqueous solution formalin is 37-40 percent formaldehyde. Common uses of formalin and
formaldehyde include tissue fixing and preservation, disinfection, and fumigation. Formaldehyde is a suspected human
carcinogen. Exposure to formaldehyde vapors can be irritating to the eyes, nose, and upper respiratory tract. In certain
individuals, repeated skin exposure to the liquid can cause sensitization that may result in allergic dermatitis.

Cal/OSHA has adopted an airborne formaldehyde permissible exposure limit (PEL) of 0.75 ppm averaged over an 8-
hour work shift. The agency has also established a short-term exposure limit (STEL) of 2 ppm over a 15 minute period.
The American Conference of Governmental Industrial Hygienists (ACGIH) has established a more restrictive Threshold
Limit Value-Ceiling (TLV-C) for formaldehyde of 0.3 ppm based on its sensory irritation properties.

If you use or store formaldehyde (or formalin) you need a Carcinogen Use Authorization. Application packets are
available from EH&S at 752-3732. Application forms are also available on the EH&S web site or in the Chemical
Carcinogen Safety Manual.

Minimizing Exposure To Formaldehyde For Health Protection

ALL WORK with formalin must be done in a chemical fume hood. If work cannot be done in a hood, contact EH&S
to take air measurements assuring that exposures are below Cal/OSHA's 0.5 ppm action level and 2 ppm STEL. EH&S
will make additional recommendations based on sampling results.

WEAR PROTECTIVE CLOTHING. Gloves must be worn whenever formalin or tissues preserved with and/or fixed
with formalin are handled. Safety goggles or a face shield must be worn whenever work activities create a potential for
splashing.
 Formaldehyde Precautions
Special Safety Precautions

If Formaldehyde contacts the body, especially the eyes, flush the affected area with water for at least 15
minutes and report to Employee Health Services. Contact lenses must not be worn in areas where formalin is
used because trapped vapors can cause irritation to the eyes. If contact lenses are required for medical
reasons, contact
EH&S at 530-752-1493.

ALL SOLUTIONS of formalin and tissues preserved in formalin must be stored in tightly sealed
containers to prevent leaks, spills, and airborne exposure.

DO NOT pour formalin waste into laboratory sinks. Formalin waste solutions must be placed in
tightly sealed, labeled waste containers. For waste pickup call EH&S Occupational Safety at 734-7324 to
submit waste disposal requests.

Small spills of dilute formalin solutions must be cleaned up immediately. Cover the spill with paper
towels or other absorbent material. Do not mop up a spill. Using a dust pan, scoop the absorbed formalin into
a plastic bag. Be sure to wear gloves and eye protection. Double bag, seal, and label the waste. Contact
EH&S for pickup. Use bleach to neutralize the formalin on any contaminated surfaces afterwards.

CAUTION: If spilled formalin causes eye, nose, or throat irritation, immediately evacuate the area, close all
doors to contain vapors, and call the UC Fire Department at 911.
Be prepared to give the location of the spill, approximate amount involved, your name, and phone number.
Have someone wait for emergency response personnel outside the building and direct them to the spill area.
 Chemical Spill Control
General Steps to follow:
1.When 1 pint or more of a hazardous substance or any amount of an extremely toxic substance is spilled or when in
doubt, call Fire Department (911). Evacuate the room, close the door, and wait for emergency personnel.
2. If the substance spilled is flammable, turn off all ignition sources before securing the room.
3. All contaminated clothing must be removed immediately. Clothes must be laundered before reuse or disposed of as
hazardous waste.
4. In case of chemical contact with skin or eyes, flood the affected area immediately with water; continue for at least 15
minutes. Seek medical assistance at Employee Health Services or for skin irritation, contact with an extremely toxic
substance, or any eye injury.
5.When incidental to one's duties, small spills (1 pint or less) may be cleaned up by laboratory personnel. It is good
laboratory practice to keep spill absorbents on hand. Absorbent material is available in Room 2107, atop the yellow
cabinets on the east side of the room.
a.Most strong acids may be absorbed and then neutralized with aqueous solutions of sodium bicarbonate,
calcium hydroxide(slaked lime), or sodium carbonate (soda ash). (Note: DO NOT attempt to absorb
hydrofluoric acid (HF). Skip this step and neutralize immediately only if you are familiar with proper
neutralization procedures for HF; otherwise, return to step one.)
b.Caustic solutions and flammable liquids may be absorbed with an inert absorbent.
c.DO NOT attempt to blot cryogenic liquid spills with unprotected hands. Wear gloves. If the cryogenic
fluid evaporates to a flammable or toxic gas, follow procedures (1) and (2) for large spills.
d.Formaldehyde spills may be absorbed with an inert absorbent. See online SafetyNet 11: "Guidelines for
the Safe Use of Formaldehyde", for more information.
e.For mercury spills, see SafetyNet 16: "Guidelines for Mercury Spill Control", for more information.
http://www.ehs.ucdavis.edu/sftynet/sn_mlist_num.cfm
f.Solid spills are not usually emergencies. If the material spilled is toxic, use dampened cloths or paper
towels to transfer it to plastic bags Brushing dry material may cause dust to become airborne.
6. .All absorbed spill material must be collected in double plastic bags or plastic containers with secure lids and
disposed of as hazardous waste. Label the container with a hazardous waste label and call Ram Naidu (916) 734-7325.If
the absorbent has been used for a flammable or volatile compound, it must be stored in a well-ventilated area away from
sources of ignition while awaiting pickup. A fume hood is a good temporary storage area. Information on the proper
procedures for handling, storage, and disposal of most common laboratory chemicals is available from EH&S at
734-7325.
 Solid Spills
Solid spills are not usually emergencies. If the material spilled is toxic, use
dampened cloths or paper towels to transfer it to plastic bags. Brushing dry
material may cause dust to become airborne.

1. All absorbed spill material must be collected in double plastic bags or plastic
containers with secure lids and disposed of as hazardous waste. Label the
container with a hazardous waste label and request a hazardous waste pickup at
4-7324. If the absorbent has been used for a flammable or volatile compound, it
must be stored in a well-ventilated area away from sources of ignition while
awaiting pickup. A fume hood is a good temporary storage area.

A general-purpose spill absorbent is available in Room 2208. Use it!

 Radiation Safety
YOU MUST BE CERTIFIED BEFORE USING ANY
XRAY EQUIPMENT IN THE LAB
1) Strict adherence to all radiation safety procedures as
defined in the UCD Radiation Safety Manual (located in
room 2107) is required.
2) A radiation safety course is required every three years if
you are going to be using any radioisotopes or radiation
producing machines.
3) Talk to the Lab Coordinator if you need to get certified
for any radiation use.
4) Always wear your dosimetry badge when using any
ionizing radiation producing machine or isotopes.
5) Always wear gloves and protective clothing when using
radioactive isotopes.
6) Always wear lead apron and gloves if you are going to
be located near a specimen that is being X-rayed.
Radiation Waste Minimization
Use smaller (3 ml) scintillation vials instead of the larger (10 ml) vials.

Use radioisotopes with half lives less than 90 days.

Dry waste contaminated with short-lived radioisotopes is incorporated into the EH&S
decay-in-storage program. This reduces the amount of waste at radioactive waste
disposal sites. Separate short-lived radioisotopes (half-life less than 90 days) from
long-lived radioisotopes in dry waste.

Separate organic, toxic, or corrosive solutions from aqueous nontoxic or noncorrosive

solutions.

Do not put dry radioactive waste containers near regular trash containers. This will
reduce the possibility that non radioactive waste will be inadvertently put into the
radioactive waste container.

If applicable, carefully run a meter at a rate of two inches per second and one-half
inch above the surface of potentially contaminated dry waste. If the surface dry waste
is less than two times background, deface all radioactive symbols and put in regular
trash container.

Aqueous solutions with pH between 2 and 5 or 9 and 12.5 should be normalized

prior to placement in the approved Office of Environmental Health and Safety/UCDHS
Health Physics waste jug.
 Disposal of Radioactive Waste
Scintillation Vials
Separate scintillation vials with activities less than 0.05 µCi/ml of 3H or 14C from
other scintillation vials.
If you buy vials in bulk and need empty flats or boxes, call Health Physics
at 4-3355. Pack the vials in the original shipping boxes or strap up to five
flats together. Avoid placing tape directly on the vials by using a cardboard
or stiff paper cover or wrapping the flats in absorbent paper. Clearly
identify the radionuclides and activities contained in each box on the
Radioactive Waste Label.
Nonradioactive, environmentally safe scintillation cocktails may NOT be
disposed of down sink drains. Call Health Physics at 4-3355 to
request a waste pickup.

Radioactive Waste Containing Biologicals

Double-bag biological waste in 4-mil, clear plastic bags for disposal. Seal
the bags and attach a completed Radiation Waste label. Clearly identify
the radionuclide, activity and weight (in pounds) contained in each bag. |

Biological waste bagged as biohazardous must be sterilized or

autoclaved before disposal as radioactive waste.

Freeze the biological waste until pickup.

 Animal Projects
Animal Project Requirements for Participants

Participants must do the following before working on an animal project:

• Complete Animal Care and Use 101
• Complete and submit Occupational Health forms
• Use the Hazard Analysis Tools from EH&S http://ehs.ucdavis.edu/animal/risk/index.cfm
• Have your name on or have it amended to the Animal Use Protocol
• Receive training on proper handling of the animal species used in the project
• Receive training on personal hygiene and the personal protective equipment to be used
• Receive training in Aseptic Technique and any special procedures related to the project
• Read and understand the procedures approved for the project in the Animal Use Protocol
• Receive instructions in proper completion and storage of Animal Surgery Logs
• Update Training Records
• “Everyone working on live vertebrate animals must be qualified, informed and trained.”
– SafetyNet#116
 Things to Know About Animal
Projects
• You can submit an Animal Use Protocol BEFORE you’ve taken the animal classes or
have funding for the project. HOWEVER, training for everyone listed on the Protocol
must be completed BEFORE the protocol is approved.
• IACUC normal turnaround time for Protocol approval is 6 to 8 weeks.
• All Animal Use Protocols need to be reviewed by Shane Curtiss before being submitted
to IACUC.
• Copies of all Active Animal Use Protocols are kept in Room 2208 in the lab.
• You should call the Campus Vet for help whenever one of your animals is sick or you
are having trouble or have questions about anesthesia, surgical techniques or post op
care.
• Rodent Survival Surgery requires aseptic technique, sterile instruments for each animal
and the surgical site must be clipped and scrubbed. Surgeons must wear a minimum of a
mask, sterile gloves and a clean scrub shirt or lab coat.
• Nonsurvival Rodent Surgeries require a minimum of clean instruments, a clipped
surgical site and the surgeon must wear gloves.
• Exposed sutures and staples must be removed from the incision site within 7 to 10 days.
• “Laboratory Study Areas” are rooms animals can be housed for up to 12 hours.
Disposal of Animal Waste
Healthy animals not treated with chemicals,
radioisotopes, or biohazardous agents
Place animal parts, tissue, waste and carcasses
(small and large animals) in tightly sealed plastic
bags in the Dead Animal Waste freezer in the
basement of Research 3. Carcasses will be sent off
campus to a rendering company or incinerated.

Animals treated with chemical, radioactive, or

biohazardous agents
Contact EH&S (4-3355) to develop a written
handling, transportation and treatment and/or
disposal procedure.
Specialized Equipment Use
Talk to a staff member prior to using any equipment for the first time

Histology Lab
Microtomes
Embedding
Diamond Saws
Staining
Blade Sharpening

Biochemistry Lab
Balances
Centrifuges
Chemicals ( Acid, Base, Teratogen, etc.)
Glassware use
Ph Meter / Ion Meter
Stir Plates/ Hot plates
Fume Hoods
 Specialized Equipment Use
Tissue Culture Lab
Sterile procedures
Glassware use
Incubator operation
Autoclave
Microscope use
Hemocytometer
Centrifugation
Cell Isolation
Bio Hoods
Media Preparation
Machine, Material Testing
& Electronics Shops
Band saws
Mills
Lathe
Drill press
Hand Drills
Tap & Dye Set
Soldering
Sanding
Vacuum System
Instron Machine & Computers
 Effective Use of Autoclaves
Steam sterilization of materials is a dependable procedure for the destruction
of all forms of microbial life. They are common laboratory tools that must
be properly used to be effective. This establishes guidelines for the
effective use of steam sterilizers (autoclaves) for the decontamination of
cultures and other potentially biohazardous materials.
Containers: Materials that are to be decontaminated should be carried to the
autoclave in leak-proof containers.
Personnel should wear proper personal protective equipment, i.e. heat
resistant gloves, eye protection and a lab coat, particularly when
unloading the autoclave.
At the end of a decontamination cycle make sure that the pressure in the
autoclave chamber is near zero before opening the door. Slowly crack
open the autoclave door and allow the steam to gradually escape from
within the autoclave.
Machine Shop & Material
Testing Safety
1) Get checked out by the biomechanics technician before using
any equipment for the first time.

2) Always wear protective eyewear. Goggles or facemasks are

acceptable, regular prescription eyeglasses are not. Don’t wear
loose clothing or jewelry when operating equipment.

3) You can not operate equipment alone in the lab, especially after
hours or on holidays.

4) If you are working with human tissue refer to the above section
on handling human tissue.

5) Use only the designated band saw and be sure to use the
vacuum dust collection system when cutting bone.
ORL Golden Rules
1. If you open it, close it.
2. If you turn it on, turn it off.
3. If you unlock it, lock it
4. If you break it, fix it.
5. If you can’t fix it, find someone who can.
6. If you borrow it, return it.
7. If you use it, take care of it
8. If you make a mess, clean it up.
9. If you take it out or move it, put it back.
10. If it belongs to someone else and you want to use it, get
permission
If you have a question about…
Personnel ask Kim Pierson 4-3311
Accounts ask Jackie Dalke 4-8650
Ordering Supplies ask Jackie Dalke 4-8650
Safety ask M Anderson 4-5760
Cadaveric Specimens ask M Anderson 4-5760
Animal Protocols ask M Anderson 4-5760
X-rays ask M Anderson 4-5760
Histology ask M Anderson 4-5760
Materials Testing ask M Anderson 4-5760
 Orthopaedic Research lab
My signature indicates that I have read and understand the health and
safety policies and procedures in the Orientation manual at SOM:
Orthopaedic Research Laboratories. This form has also been signed by
the administrator and the Principal Investigator.
Name- Print:
Sign: Date:
Email:
Duties:
Principal Investigator:

Administrator:

Turn in this completed form to Lab Coordinator.