€ PARASON vonparason com Ij Low-Consistency Pulping Loop SMe sacra gan i Oem kets * Junk Trap Oars Oe Racer SNC eud Oey t OCLOW CONSISTENCY PULPER Results of Flow simulation performed using latest computational fluid dynamics software Operating Principles 'D' Section of tub is to increase the turbulence in the Tub causing bales/bundles to submerge rapidly thus, reduce the dwelling time suitable for continuous operations. Suitable for furnish of OCC, AOC, Box Board and to separate the reject and fiber. The Fiber discharge line is connected to the pulp suction pump or directly fed to the storage towers. Application & Features > The model 'D' refers to the shape of Tub ~ Continuous Operation > Operating consistency 4-696 > Higher capacity (TPD) with reduced power input compared to normal vertical Pulper SS. Cast Rotor of special design for handling different grade of raw material 'D'Pulper can be operated at ambient temp . as well as at elevated temp. upto 70°C — Heavy duty sturdy bearings take impact load of bales/waste paper bundles > Removes plastic in large pieces with little degradation — Reduce burden on downstream equipment — Decreases/eliminates clean out down time Technical Specification Motor RPM = 980 Capacitym? 6 8 10 2 16 18 20 2 PD 25-30 40:50 70-75 70-90 110-120 429-140 140-150 150-160 Power (kw) 75 90 110 132 150 180 200 20 Capacity m* 26 oa 35 40 50 60 70 PD 200-250 250-300 300-330 «350-400 400-450 450-500 600-650 Power (kw) 250 315 355 400 450 550 600Application & Features Removal of spinning contaminants such as wires, rags, strings, plastics by means of ragger rope. Easy installation with horizontal and vertical type of pulper. Adjustable time delay for intervals and running time of the drive motor, the speed of ragger can be matched to the level of contaminants of the waste paper and the production rate required. Pneumatic loading and relieving of the loading rope. Ragger control panel is designed to ~ Loading and lifting of the roller in auto mode ~ Speed control at 0-10RPM = Emergency stop - Visual indications of ragger motor ‘ON’ and air pressure Main Specification PRG Model 1 2 RPM 0.19 0.19 Geared Motor 14 22 ROPE CUTER It is an integral part of Ragger system whereby the ragger rope string is cut at regular interval Application & Salient Features — Used for cutting ragger rope ~ Double hydraulic cylinders give it a strong cutting abilityES Results of Flow simulation performed using latest computational fluid dynamics software Advantages — Uncut contaminants from low-consistency pulper are removed with negligible fiber loss > The Fiber saver works as continuous cleaning equipment for pulper and helps in throughput increase — Removal of large foreign contaminants eliminates the risk of pulp jamming in successive operation > The contaminants discharge cycle can be operated through PLC based (Time control) panel Main Specification ‘Motor RPM = 1470 DFS MODEL 7 9 R 1215 15 15.18 Capacity (m*) os 1 23 4 45 6 Power(kw) 25 35 75 90 125 132 P&I Diagram of \OW-Consistency Pulper & Loop mer ACCEPT Grapple REJECT HB DLUTION water Junk TrapMMEL SCREEN Application & Features To lessen the contaminant load on Fiber Saver (PFS), the light rejects normally directed to Trommel Screen. Special heavy duty perforated drum with hole size in ascending order and aided by suitable shower in side & out side allowing the recovery of fibers. The coarse contaminants getting rejected and accept is returned to the pulper. Advantages Easy Installation. > Perforated drum of $5-304, drive arrangement, inside helical screw, out let chute of SS-304 and Supporting Structure of MS. > Drumis driven through Geared Motor, Pulleys and Belts > Cldrive and driven pulleys properly machined > Shower pipe with nozzles of SS-304 Technical Specification ‘TSR MODEL, 1 2 PD 8:15 15-20 POWER(KW) 37 55 MOTOR RPM = 1500 3 4 7 20-25 25-30 35-40 75 95 11 GRAPPLE > Adopts stainless steel material, long ser Grapple is mainly used in continuous pulping system for grappling heavy and large impurities from sediment well. Application & Salient Feature — Mainly used for grappling heavy and large impurities from sediment well. Four “petal” is air pressure type operation. > Easy to maintain and operate. life.Dt ty eas PTET Tee ras) Features & Benefits Superior Metallurgy of refiner disc adopted in the impellers The special heat treatment with same hardness throughout the cross section No harsh hardfacing which leads to fast wear of the screen plates Extended life for the screen plates. After first use, rebuilding possible ( good weldability) Optimum mechanical strength for wear and tear with toughness The surface colour is grayish due to heat treatment having self protective layer of passivated surface Electro-Dynamically balanced bibidod Reduce Power Consumption by 20-30% Results of Flow simulation performed using atest computational fluid dynamics software Less Power, More open aresBIGGEST DIAMETER ROTOR (2150 MM} NOW AVAILABLE Rotor for 70m* Pulper MOC: Duplex 2205 (Weight 1000 ke) Advantages ~ Parason has different metallurgy & geometry of rotors for different furnishes > Uniform agitation, better pulping ~ Computational fluid dynamics simulation for better pulping IS LC Pulper Rotor Fiber Saver Impeller x ater Before Dynamo Rotor Series RebuildingSS a GUARANTEES THE BEST PERFORMANCE Manufactured with CNC machines to ensure high accuracy LC Pulper Screen Plate Fiber Saver Screen Plate 1 Ke Rotating Assembly For Dynamo Rotor Series Fiber Saver Impeller LC Pulper & Fiber Saver the refining perple Corporate Office: Golden Dreams IT Park, &th Floor, €-27, Chikalthana MIDC Beside Millennium Park, Aurangabad (MH), India - 431006 Tel: 91(0) 240 - 2339234/35/36/37 Email: [email protected] Customer Service No: +91 (0) 240 - 6644 218 Web : www.parason.com Customer Service Email: [email protected] FOLLOW US| e000 Note: Content subject te change without any rior notice | Power cansumed may vary as per furnish combinations “No partaf this catalog may be reproduced or coped in any farm or by any means Igraphic, electronic or mechanical, including photocopying recording, ‘ping or information retrieval system] or reproduced on any isc tape, perforated media or ether information storage device, etc, without the writen permission ofthe company, Breach ofthis consition ie able for legal action.”