Scribd
Upload
43 views3 pages

Nasarc Technologies Intelliream MP Data Sheet

Intelliream torch maintenance center datasheet

Uploaded by

jjrice
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
43 views3 pages

Nasarc Technologies Intelliream MP Data Sheet

Intelliream torch maintenance center datasheet

Uploaded by

jjrice
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

intelliream mp ®

robotic torch maintenance center


Designed to improve overall welding equipment effectiveness
Extend the life of your robotic MIG torch and improve cycle time in
your robotic welding cell with the next generation Intelliream® MP.
This robotic torch maintenance center system-atically removes and
limits spatter accumulation for enhanced productivity.
The Intelliream® MP is designed with reliability in mind.
The internal components are modular and protected from the
environment.

Product advantageS
01
The Intelliream® EIP controller features a simple “No Trial - No Error” programming technique and constant process monitoring.

02
Self-centering grip design for positive traction on all nozzle sizes.

03
Complete enclosure seals out small particles and contaminants.

04
On-board diagnostics indicate position and fault codes for ease of trouble-shooting.

05
A status light signals when the unit is operating and flashes diagnostic codes if a fault occurs.

06
Dry run and sensor override modes make setting up and trouble-shooting easier.

07
The Intelliream® is the only reamer to offer an automatic retry feature.

08
De-ringer: A pilot reaming stroke removes the spatter ring that forms on the end of the weld nozzle.

TECHNICAL DATA
Footprint Size: 25” H x 13” L x 10” W
Cutter Speed: 1100 RPM
Air Driven Motor: 0.60 HP
Wire Cutter Diameter: 0.030” - 1/16”
Air Supply: 80 PSI, 16.5 SCFM
Power Supply: 24 VDC, 0.75 A
process highlights
01 High strength coated reaming bit provides enhanced wear resistance.
Precision machined to tight tolerances for optimized performance.
02 Vortex action sprayer delivers a radial spray pattern to uniformly coat
the interior surface of the nozzle. Post flow logic enables self-cleaning.
03 Pinch off wire cutter is integrated in the clamp housing for easy and
quick access, minimizing robot movement. (Optional)
04 Tapered cone provides a visual check to ensure positional accuracy of
the TCP (tool center point).

performance
The Intelliream® MP controls the entire reaming process. Every aspect
of the reaming cycle is commanded, monitored, and verified.

The feedback signal to the robot is a true cycle complete signal


indicating that the entire sequence has been executed without error.

features & benefits


01 Reset push-button overrides the Intelliream® MP commands to the cylinders and sends them
back to their home position. 3) 1)
02 Indicator LED’s are visible to an operator and show the position of air cylinders. If a fault
occurs, the on-board diagnostics report the error via flashing LED codes so the problem can be
resolved faster.
03 The settings button is used to configure several features in the Intelliream® that will optimize 2)
performance and assist in maintenance. 4)
04 Actuator pushbuttons for manual operation will assist in safely programming robot positions
and troubleshooting.
05 Auto configuration of signal polarity: no need to set DIP switches! The Intelliream® MP senses
both the input and output type of the robot and sets its I/O immediately.
06 Error signal feedback to the robot: if an error occurs in the process, the Intelliream® MP returns
to its home position and sends an error signal to the robot.
07 The electronics are enclosed in the RCM-2 control module. The control module is easily
removed from the side of the machine and disconnected without removing the front or rear
panels.
08 Magnetic sensors are utilized for optimum position accuracy and reliability
09 Hinged back door/panel for ease of access.
10 Gripper guard helps keep area clear of spatter.
11 Nozzle detect ensures that the nozzle is on the torch thus eliminating “bad” welds because
of contamination. (Optional)
ordering information
Standard Equipment

INTELLIREAM® MP IRM030001-MP
Spray System
TCP Check

Request any of the following options when ordering:


Wire Cutter Module IRW010099-00
Nozzle Detect Assembly IRE120099-02
Spray Containment Assembly II IRS020099-00
Nozzle Gas Flow Sensor IRE060099-00

Accessories
Reaming Bit, 1/2" IRB010500-00
Reaming Bit, 1/2" bottleneck
Re IRB010501-00
Reaming Bit, 15.5mm IRB01M155-00
Reaming Bit, 5/8" IRB020625-00
Reaming Bit, 3/4" IRB010750-00
Robot control cable, 20ft IRE010090-20
Robot control cable, 30ft IRE010090-30
Robot control cable, 50ft IRE010090-50
Test Box IRT020001-00
Adapter Plate IRF020002-01
Floor Mount Stand IRX010001-00
Anti Spatter Bulk Feed IRS010099-09

You might also like