Final Wallap Output File
Final Wallap Output File
SOIL PROFILE
Stratum Elevation of ------------------ Soil types -------------------
no. top of stratum Active side Passive side
1 0.00 1 Soil Type 1 1 Soil Type 1
2 -3.00 2 Soil Type 2 2 Soil Type 2
3 -16.50 3 Soll Type 3 3 Soll Type 3
4 -22.50 4 Soil Type 4 4 Soil Type 4
SOIL PROPERTIES
Bulk Young's At rest Consol Active Passive
-- Soil type -- density Modulus coeff. state. limit limit Cohesion
No. Description kN/m3 Eh,kN/m2 Ko NC/OC Ka Kp kN/m2
(Datum elev.) (dEh/dy ) (dKo/dy) ( Nu ) ( Kac ) ( Kpc ) ( dc/dy )
1 Soil Type 1 18.10 0 0.500 NC 0.285 4.287
( 11000) (0.300) (0.000) ( 0.000)
2 Soil Type 2 18.10a 0 0.500 NC 0.285 4.264
10.00b ( 31500) (0.300) (0.000) ( 0.000)
3 Soll Type 3 21.30a 36400 0.593 NC 0.368 3.051 85.00d
11.30b (0.300) (1.420) ( 4.607)
4 Soil Type 4 24.20a 0 0.500 NC 0.285 4.287
14.20b ( 43200) (0.300) (0.000) ( 0.000)
Note: (a) and (b) are Bulk Densities above and below the water table
WALL PROPERTIES
Type of structure = Fully Embedded Wall
Elevation of toe of wall = -18.75
Maximum finite element length = 1.00 m
Youngs modulus of wall E = 2.6500E+07 kN/m2
Moment of inertia of wall I = 0.010417 m4/m run
E.I = 276042 kN.m2/m run
Yield Moment of wall = Not defined
STRUTS and ANCHORS
Strut/ X-section Inclin Pre-
anchor Strut area Youngs Free -ation stress Tension
no. Elev. spacing of strut modulus length (degs) /strut allowed
m sq.m kN/m2 m kN
1 -3.00 2.00 0.000592 2.100E+08 3.00 25.00 500.0 No
2 -7.50 2.00 0.000592 2.100E+08 2.50 25.00 500.0 No
3 -11.00 2.00 0.000592 2.100E+08 2.00 25.00 500.0 No
SURCHARGE LOADS
Surch Distance Length Width Surcharge Equiv. Partial
-arge from parallel perpend. ----- kN/m2 ----- soil factor/
no. Elev. wall to wall to wall Near edge Far edge type Category
1 0.00 1.00(A) 100.00 1.00 70.00 = N/A N/A
CONSTRUCTION STAGES
Construction Stage description
stage no. --------------------------------------------------------
1 Apply surcharge no.1 at elevation 0.00
2 Apply water pressure profile no.1
3 Excavate to elevation -3.30 on PASSIVE side
4 Install strut or anchor no.1 at elevation -3.00
5 Change properties of soil type 1 to soil type 2
Ko pressures will be reset
6 Excavate to elevation -7.80 on PASSIVE side
7 Install strut or anchor no.2 at elevation -7.50
8 Apply water pressure profile no.2
9 Excavate to elevation -11.30 on PASSIVE side
10 Install strut or anchor no.3 at elevation -11.00
11 Excavate to elevation -13.75 on PASSIVE side
Stability analysis:
Method of analysis - Burland-Potts
Factor on passive for calculating wall depth = 1.50
Boundary conditions:
Length of wall (normal to plane of analysis) = 100.00 m
Maximum and minimum bending moment and shear force at each stage
Stage --------- Bending moment -------- ---------- Shear force ----------
no. maximum elev. minimum elev. maximum elev. minimum elev.
kN.m/m kN.m/m kN/m kN/m
1 7.8 -3.30 0.0 0.00 5.3 -3.00 -3.4 -16.50
2 7.8 -3.30 0.0 0.00 5.3 -3.00 -3.4 -16.50
3 111.3 -5.00 0.0 0.00 44.5 -22.50 -31.5 -16.50
4 99.3 -3.00 -0.0 0.00 98.3 -3.00 -128.2 -3.00
5 102.0 -3.00 -0.0 0.00 100.5 -3.00 -130.7 -3.00
6 108.5 -3.00 -11.7 -6.00 103.4 -3.00 -152.9 -3.00
7 99.1 -7.50 -13.3 -5.00 115.5 -7.50 -149.5 -3.00
8 104.5 -7.50 -13.2 -5.00 141.3 -22.50 -151.0 -3.00
9 115.4 -7.50 -26.5 -10.00 184.0 -22.50 -153.9 -3.00
10 101.5 -3.00 -12.2 -5.00 184.0 -22.50 -151.8 -3.00
11 107.3 -7.50 -12.6 -5.00 180.2 -22.50 -154.0 -3.00