Scribd
Upload
3 views

04 Adding POTS Users

Uploaded by

elahi elahi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
3 views

04 Adding POTS Users

Uploaded by

elahi elahi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Configuring the PSTN User Data

This topic describes how to configure the PSTN user data (the same as the corresponding data on
the IMS) on the SIP interface so that the POTS terminal can access the network to implement the
VoIP service.

Prerequisite

The POTS service board must be inserted into the planned slot.

NOTE:

You can add a service board in two ways (see the Usage Guideline of the board add command).
It is recommended that you insert the service board into the planned slot and then confirm the
board.

Context

Table 1 lists the default settings of the attributes of the PSTN user. When configuring the
attributes of the PSTN user, you need to modify them according to the service requirements.

Table 1 Default settings of the attributes of the PSTN user


Parameter Default Setting
Priority cat3
PotsLineType DEL
Sequence of sending the phone number Ringing and then sending the phone number
of the calling party
Format of the phone number of the SDMF(FSK)
calling party
Power-off interval 100ms
FSK delay interval 800ms
Whether to enable or disable VQE Disable
automatic gain
Whether to enable or disable VQE Disable
noise suppression
Target value of VQE automatic gain -22 dBm0
Target value of VQE noise suppression 12 dB
Input gain of the DSP chip 0 dB

1
Table 1 Default settings of the attributes of the PSTN user
Parameter Default Setting
Output gain of the DSP chip 0 dB
Name of the DSP parameter profile - (Indicates that the DSP parameter profile is not
configured.)
Whether to support the detection of the Not support
ANSbar signal through monophony
Whether to support the bell ANS signal Not support
Display mode of the FSK phone BELL_202
number of the calling party
TAS CID mode NO-TAS

Procedure

1. In global config mode, run the board confirm command to confirm the service board.

NOTE:

You need not run this command if the board is integrated in the mother board.

2. Add a PSTN user.


a. In global config mode, run the esl user command to enter the ESL user mode.
b. Run the sippstnuser add or sippstnuser batadd command to add a PSTN user or
add PSTN users in batches.

CAUTION:

When adding a user, you can configure the phone number (parameter telno).
When the public ID is generated by phone number, you must enter the phone
number. It is recommended that you configure this phone number to be the same
as the phone number configured on the IMS. In addition, ensure that the phone
number is unique on the AG.

c. Run the display sippstnuser command to check whether the PSTN user data is
the same as the planned data.
3. (Optional) Configure the attributes of a PSTN user.

The attributes of a PSTN user need to be configured when the default settings are
inconsistent with the actual application.

2
a. Run the sippstnuser attribute set or sippstnuser attribute batset command to
configure the attributes of a PSTN user.
b. Run the display sippstnuser attribute command to check whether the attributes
of the PSTN user are the same as the planned data.

Example

Assume that the phone numbers of 16 PSTN users are 83120000-83120015 and the default
values are used for other attributes. To add the 16 PSTN users in slot 0/3 on SIP interface 0 in
batches, do as follows:

huawei(config)#esl user
huawei(config-esl-user)#sippstnuser batadd 0/3/0 0/3/15 0 telno 83120000
step 1
huawei(config-esl-user)#display sippstnuser 0/3
---------------------------------------
F /S /P MGID TelNo
---------------------------------------
0 /3 /0 0 83120000
......
0 /3 /14 0 83120014
0 /3 /15 0 83120015
---------------------------------------

3
‫پایان‬

‫‪4‬‬

You might also like