Prepared by: Lenovo

Date: Sunday, July 21, 2024

 Prepared by: Lenovo

Report Contents
Design 1___________________________________________________________________________________________________ 2
Scenario 1 ................................................................................................................................................................................................ 2
Materials ............................................................................................................................................................................................. 2
boundary conditions ..................................................................................................................................................................... 3
Initial Conditions ............................................................................................................................................................................ 3
mesh ..................................................................................................................................................................................................... 4
Physics ................................................................................................................................................................................................. 5
Solver Settings .................................................................................................................................................................................. 6
Convergence ...................................................................................................................................................................................... 6
Results ................................................................................................................................................................................................. 7

Decision Center _________________________________________________________________________________________ 10

Page 1 Generated with Autodesk CFD 2024

 Prepared by: Lenovo

Design 1
Length units cm
Coordinate system Cartesian 3D

SCENARIO 1
MATERIALS

Page 2 Generated with Autodesk CFD 2024

 Prepared by: Lenovo

NAME ASSIGNED TO PROPERTIES

Aluminum NICKS SIDE 2:1 X-Direction 204.0 W/m-K
rear mount:2 Y-Direction Same as X-dir.
blade:1
rear mount:2_U_blade:1 Z-Direction Same as X-dir.
blade:1@blade with internals - Density 2707.0 kg/m3
Copy:1 Specific heat 896.0 J/kg-K
supports:3@blade with internals Emissivity 0.2
- Copy:1
Transmissivity 0.0
supports:3
rear mount:1 Electrical resistivity 2.7e-08 ohm-m
rear mount:1_U_blade:1 Wall roughness 0.0 meter
supports:2@blade with internals
- Copy:1
supports:2
NICKS SIDE:1
Volume
Volume
Volume
Volume
Volume
Volume

BOUNDARY CONDITIONS
TYPE ASSIGNED TO
Velocity Normal(30 m/s) Surface:10
Surface:2218

Velocity Normal(100 km/h) Surface:36

Surface:38
Surface:46
Surface:2193
Surface:2195
Surface:2197
Surface:2199

INITIAL CONDITIONS
TYPE ASSIGNED TO

Page 3 Generated with Autodesk CFD 2024

 Prepared by: Lenovo

MESH
Automatic Meshing Settings
Surface refinement False
Gap refinement False
Resolution factor 1.0
Edge growth rate 1.1
Minimum points on edge 2
Points on longest edge 10
Surface limiting aspect ratio 20

Mesh Enhancement Settings

Mesh enhancement True
Enhancement blending False
Number of layers 3
Layer factor 0.45
Layer gradation 0.0

Page 4 Generated with Autodesk CFD 2024

 Prepared by: Lenovo

Meshed Model

Number of Nodes 6022

Number of Elements 19929

PHYSICS
Flow On
Compressibility
Heat Transfer On
Auto Forced Convection On
Gravity Components 0.0, 0.0, 0.0
Radiation Off
Scalar No scalar
Turbulence On

Page 5 Generated with Autodesk CFD 2024

 Prepared by: Lenovo

SOLVER SETTINGS
Solution mode Steady State
Solver computer MyComputer
Intelligent solution control On
Advection scheme ADV 5
Turbulence model k-epsilon

CONVERGENCE
Iterations run 9
Solve time -1721523762 seconds
Solver version 24.1.10

Energy Balance

Mass Balance
IN OUT
Mass flow 2649100.0 g/s N.A.
Volume flow 978611.0 cm^3/s N.A.

Page 6 Generated with Autodesk CFD 2024

 Prepared by: Lenovo

RESULTS

Inlets and Outlets

inlet 1 inlet bulk pressure 0.0 dyne/cm^2

inlet bulk temperature 0.0 C
inlet mach number 0.0
mass flow in 1252020.0 g/s
minimum x,y,z of 0.0
opening
node near minimum 2991.0
x,y,z of opening
reynolds number 0.0
surface id 2193.0
volume flow in 462511.0 cm^3/s
inlet 2 inlet bulk pressure 0.0 dyne/cm^2
inlet bulk temperature 0.0 C
inlet mach number 0.0
mass flow in 1397080.0 g/s
minimum x,y,z of 0.0
opening

Page 7 Generated with Autodesk CFD 2024

 Prepared by: Lenovo

node near minimum 79.0

x,y,z of opening
reynolds number 0.0
surface id 10.0
total mass flow in 2649100.0 g/s
total vol. flow in 978611.0 cm^3/s
volume flow in 516100.0 cm^3/s

Field Variable Results

VARIABLE MAX MIN
cond 2.04 W/cm-K 2.04 W/cm-K
dens 2.707 g/cm^3 2.707 g/cm^3
econd 0.0 W/cm-K 0.0 W/cm-K
emiss 0.0 0.0
evisc 0.0 g/cm-s 0.0 g/cm-s
gent 0.0 1/s 0.0 1/s
press 0.0 dyne/cm^2 0.0 dyne/cm^2
ptotl 12181500.0 dyne/cm^2 0.0 dyne/cm^2
scal1 0.0 0.0
seebeck 0.0 V/K 0.0 V/K
shgc 0.0 0.0
spech 0.896 J/g-K 0.896 J/g-K
temp 0.0 C 0.0 C
transmiss 0.0 0.0
turbd 0.0 cm^2/s^3 0.0 cm^2/s^3
turbk 0.0 cm^2/s^2 0.0 cm^2/s^2
ufactor 0.0 0.0
visc 0.0 g/cm-s 0.0 g/cm-s
vx vel 1566.85 cm/s 0.0 cm/s
vy vel 0.0 cm/s -2293.7 cm/s
vz vel 2777.78 cm/s -3000.0 cm/s
wrough 0.0 cm 0.0 cm

Component Thermal Summary

PART MINIMUM MAXIMUM VOLUME AVERAGED
TEMPERATURE TEMPERATURE TEMPERATURE
NICKS SIDE 2:1 0 0 0
rear mount:2 0 0 0
blade:1 0 0 0
rear mount:2_U_blade:1 0 0 0
blade:1@blade with 0 0 0
internals - Copy:1
supports:3@blade with 0 0 0
internals - Copy:1
supports:3 0 0 0
rear mount:1 0 0 0
rear mount:1_U_blade:1 0 0 0

Page 8 Generated with Autodesk CFD 2024

 Prepared by: Lenovo

supports:2@blade with 0 0 0
internals - Copy:1
supports:2 0 0 0
NICKS SIDE:1 0 0 0
Volume 0 0 0
Volume 0 0 0
Volume 0 0 0
Volume 0 0 0
Volume 0 0 0
Volume 0 0 0

Fluid Forces on Walls

pressx 0.0 dynes
pressy 0.0 dynes
pressz 0.0 dynes
shearx 0.0 dynes
sheary 0.0 dynes
shearz 0.0 dynes

Page 9 Generated with Autodesk CFD 2024

 Prepared by: Lenovo

Decision Center

Page 10 Generated with Autodesk CFD 2024