Scribd
Upload
232 views3 pages

Precedure To Fit A Used MFP Board Revision 6

Uploaded by

unfatarat
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
232 views3 pages

Precedure To Fit A Used MFP Board Revision 6

Uploaded by

unfatarat
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

27th November 2013

Revision 6
UK Technical Support Group
Doc ID –TNGB1200135EN

Products: C224e C284e C364e C454e C554e C654e C754e


C224 C284 C364 C454 C554 C654 C754
Mono 224e 284e 364e 454e 554e
Mono 654(e) 754(e)

Procedure to Fit a Used MFP Board for Testing

It is only possible to exchange a used MFPB board from one machine to another for
testing purposes if you follow the procedure below.

If the procedure is not followed the data will be corrupted, Counters may be lost or
corrupted, and permanent data loss could result in a dead device!

(If you are fitting a new MFPB board, follow the installation instructions detailed in the
latest service manual.)

Before you start, please ensure you have the correct “


MFP reset”Tool:

Colour Products ~ A145FW.TAR


Mono 654(e) to 754(e) ~ A55VFW.TAR
Mono 224e to 554e ~ A61FFW.TAR

Please note that the SSD board must never be exchanged from one machine to
another as this will cause the corruption of data.

Related Part Numbers: (always double check the part number in the latest Parts Guide!)

Machine MFP Board part number


C224 A4FMH02204
C284 \ C364 A161H02204
C454 \ C554 \ C654 \ C754 A2XKH02004
C224e \ C284e \ C364e \ C454e \C554e A5C1H02007
C654e\C754e A2X0H02001
MONO 224e 284e 364e 454e 554e A161FH02001
MONO 654 \ 754 A55VH02001
MONO 654e \ 754e A55VH02301

Note: Always label boards and components when removing and fitting to
another machine.

1
Procedure
1. Fit the used MFP board to the machine and refit all components.

At this point do not power up the machine as the previously used MFPB now
needs the Firmware to be installed.

2. Turn ON the MFP, and close the front door within 3 seconds….
3. Install Firmware taking care to set the “
machine”and “ type”as per the table below:

Firmware Update Screen: Enter correct “


Machine”and “
type”
–Press “
Machine Type Select” Information”

Latest “
machine”and “
type”information:

4. Continue to complete the FW upgrade as normal.

When completed - Turn the main SW OFF. Do NOT power the machine back ON!

At this point do not power up the machine as the previously used MFP Board now
needs to be reset using the “MFP reset tool”by the following procedure…..
2
MFP Reset Procedure:

5. Copy "AxxxxFW.tar" in the root folder of USB flash memory.

Colour Products ~ A145FW.TAR


Mono 654(e) to 754(e) ~ A55VFW.TAR
Mono 224e to 554e ~ A61FFW.TAR

6. Install the USB flash memory into USB slot for FW download.
7. Turn the main SW ON.
8."Data initialization completed!" is shown.

9. Turn the main SW OFF.

10. Pull the USB flash memory out of the Firmware Slot

11. Turn the main SW ON.

12. C-D390 is shown on the operation panel and the writing will be in Japanese! –DO
NOTHING YET…..

At this point the machine may reboot 2 times, Wait until the “
Recover Data" button is
shown as in the picture below.

13. Touch the "Recover Data" button to restore the data from SSD board to MFP board.

14. When complete turn OFF the main power switch.

15. Switch the machine back on and check the Serial Numbers and Meter readings and
counters match your device
End.
3
Related Information –TNGB1301569EN –Procedures and Guidelines for Board Replacement

You might also like