Seat No.: ________ Enrolment No.

___________

GUJARAT TECHNOLOGICAL UNIVERSITY

BE - SEMESTER–IV (NEW) EXAMINATION – SUMMER 2022
Subject Code:3141706 Date:23-06-2022
Subject Name:Analog Signal Processing
Time:10:30 AM TO 01:00 PM Total Marks: 70
Instructions:
1. Attempt all questions.
2. Make suitable assumptions wherever necessary.
3. Figures to the right indicate full marks.
4. Simple and non-programmable scientific calculators are allowed.
Marks
Q.1 (a) Define following. 03
1. Input Bias Current
2. Output voltage Swing
3. Total output offset Voltage.
(b) Enlist and draw the Differential Amplifier Configuration. 04
(c) Draw & Explain - 5 V Power supply using 7905 IC. 07

Q.2 (a) Draw pin diagram of 741 Op-Amp IC. 03

(b) Explain basic idea about compensating network for offset 04
voltage compensation.
(c) Enlist and draw the Block diagram representation of feedback 07
configuration.
OR
(c) Explain the Inverting Amplifier and also derive the equation 07
for Voltage gain.

Q.3 (a) Draw the circuit diagram for Current to Voltage Converter. 03
(b) Draw and explain in brief Non-Inverting Amplifier with 04
external offset voltage compensating network.
(c) Explain Voltage to Current Converter with its circuit diagram 07
and derivation.
OR
Q.3 (a) Explain limitation of OPAMP as a Comparator circuit. 03
(b) Draw and explain in brief: Small Signal Half wave rectifier 04
using an OPAMP.
(c) Explain Summing Amplifier for Differential Configuration of 07
an Op Amp.

Q.4 (a) Draw the circuit diagram of Active first order low pass Butter 03
worth filter.
(b) Draw and explain in brief Successive Approximation type 04
Analog to Digital Converter.
(c) Explain Practical Differentiator circuit with frequency 07
response.
OR
Q.4 (a) Enlist the various types of filter configuration. 03
(b) Draw and Explain Sample and Hold circuit using an OPAMP. 04
(c) Explain Practical Integrator circuit with frequency response. 07

Q.5 (a) Explain Wein bridge Oscillator. 03

1
 (b) Explain Voltage Controlled Oscillator (VCO). 04
(c) Explain Instrumentation Amplifier using three OPAMP with 07
resistance transducer and Bridge circuit.
OR
Q.5 (a) Explain Programmable Gain Amplifier 03
(b) Draw and Explain pin configuration of 555 timer IC with its 04
function.
(c) Explain the any one application of 555 timer IC for 07
Monostable Operation.
*********

2
Seat No.: ________ Enrolment No.___________

GUJARAT TECHNOLOGICAL UNIVERSITY

BE - SEMESTER–IV(NEW) EXAMINATION – WINTER 2022
Subject Code:3141706 Date:13-12-2022
Subject Name:Analog Signal Processing
Time:10:30 AM TO 01:00 PM Total Marks:70
Instructions:
1. Attempt all questions.
2. Make suitable assumptions wherever necessary.
3. Figures to the right indicate full marks.
4. Simple and non-programmable scientific calculators are allowed.
MARKS
Q.1 (a) State the characteristics of an ideal op amp. 03
(b) Define following terms with respect to op-amp: 04
(1) Input offset voltage
(2) Virtual ground
(3) Common Mode Rejection Ratio (CMRR)
(4) Slew Rate
(c) Discuss the design of three op-amp based instrumentation amplifier. 07
Derive the equation for its voltage gain.

Q.2 (a) Briefly discuss Wein bridge oscillator. 03

(b) Briefly explain the concept of peaking amplifier with its circuit diagram. 04
(c) Discuss voltage series feedback amplifier (closed loop non inverting 07
amplifier) with circuit diagram. Derive the equation for its voltage gain
and also exaplain its application as voltage follower.
OR
(c) Discuss voltage shunt feedback amplifier (closed loop inverting 07
amplifier) with circuit diagram. Derive the equation for its voltage gain
and also exaplain its application as inverter.

Q.3 (a) Briefly describe the circuit of zero crossing detector 03

(b) Explain the circuit of op-amp based precision half-wave rectifier. 04
(c) Discuss op-amp based basic and practical differentiator circuit with its 07
frequency response, necessary equation and waveforms.
OR
Q.3 (a) Give barkhausen criteria for oscillator design. 03
(b) Briefly explain Successive Approximation Register (SAR) type ADC. 04
(c) Discuss in detail the design of op-amp based Schmitt trigger circuit 07
along with necessary equations and waveforms.

Q.4 (a) Explain the circuit of op-amp based phase shift oscillator. 03
(b) Briefly explain the block diagram of Voltage Controlled Oscillator 04
(VCO) ?
(c) Explain first order high pass filter operation with frequency response curve. 07
Design first order high pass filter with a cut-off frequency of 1.25kHz and
passband gain of 2.Assume C=0.01μf.
OR
Q.4 (a) Draw and explain Notch filter in brief. 03
(b) Briefly discuss the circuit of all pass filter. 04
(c) Explain the operation of IC 555 timer based astable multivibrator circuit. 07

1
Q.5 (a) What is the use of ICs 78XX and 79XX ? 03
(b) Discuss the circuit of voltage to current converter with grounded load 04
and derive the relation between input voltage and output current.
(c) Discuss the design of monostable multivibrator circuit along with 07
waveforms. Also derive the equation tp = 1.1RC
OR
Q.5 (a) Draw the pin diagram and internal block diagram of IC 555 timer. 03
(b) Briefly explain the circuit of logarithmic amplifier with its equation. 04
(c) Explain the operation of R-2R ladder type DAC. 07

*************

2
Seat No.: ________ Enrolment No.___________

GUJARAT TECHNOLOGICAL UNIVERSITY

BE - SEMESTER–IV (NEW) EXAMINATION – SUMMER 2021
Subject Code:3141706 Date:03/09/2021
Subject Name:Analog Signal Processing
Time:02:30 PM TO 05:00 PM Total Marks: 70
Instructions:
1. Attempt all questions.
2. Make suitable assumptions wherever necessary.
3. Figures to the right indicate full marks.
4. Simple and non-programmable scientific calculators are allowed.

MARKS
Q.1 (a) Draw and Explain equivalent circuit of the Op-Amp. 03
(b) Define and explain the terms of op-amp as:- Input offset voltage, Input 04
bias current, Common mode rejection ratio, Output resistance.
(c) Explain the Voltage series feedback amplifier (Non-inverting amplifier 07
with feedback) and derive the equation of close loop voltage gain.

Q.2 (a) Explain voltage follower and its application. 03

(b) Explain the differential amplifier with one op-amp. 04
(c) Explain summing, scaling and averaging amplifier using inverting 07
configuration of operational amplifier.
OR
(c) Derive the gain formula of Voltage shunt feedback amplifier. 07
Q.3 (a) Explain how an operational amplifier is used as integrator. 03
(b) Draw the circuit: (1) Narrow Band Reject filter (2)Low pass filter. 04
(c) Discuss briefly about D/A converter with binary - weighted resistor. 07
OR
Q.3 (a) Explain Passive high pass circuit. 03
(b) Describe the working of Zero crossing detector 04
(c) Explain Schmitt trigger circuit along with circuit diagram. 07
Q.4 (a) Draw and explain the circuit diagram of the Negative Clipper. 03
(b) Explain the offset voltage compensating network for non-inverting 04
amplifier.
(c) Explain the Sample and hold circuit. 07
OR
Q.4 (a) Explain the Phase shift oscillator.. 03
(b) Write a short note on instrumentation amplifier using three op-amps. 04
(c) Explain basic comparator with its input and output waveforms. 07
Q.5 (a) Explain Logarithmic amplifier. 03
(b) Explain Wien bridge oscillator. 04
(c) Explain the monostable multivibrator using 555 timer with its internal 07
block diagram and its timing waveforms.
OR
Q.5 (a) Enlist Ideal characteristics of an Op-Amp. 03
(b) Explain voltage to current converter with grounded load. 04
(c) Explain the astable multivibrator using 555 timer with its internal 07
block diagram and its timing waveforms.

*************

1
Seat No.: ________ Enrolment No.___________

GUJARAT TECHNOLOGICAL UNIVERSITY

BE - SEMESTER–IV (NEW) EXAMINATION – WINTER 2021
Subject Code:3141706 Date:31/12/2021
Subject Name:Analog Signal Processing
Time:10:30 AM TO 01:00 PM Total Marks: 70
Instructions:
1. Attempt all questions.
2. Make suitable assumptions wherever necessary.
3. Figures to the right indicate full marks.
4. Simple and non-programmable scientific calculators are allowed.

MARKS
Q.1 (a) Draw a block diagram of typical OP-AMP 03
(b) Define (i) CMRR (ii) Slew Rate (iii) Input Bias Current (iv) Input 04
Offset Current
(c) Draw voltage series feedback amplifier using op-amp & derive the 07
equation of closed loop voltage gain.

Q.2 (a) Design a summing amplifier circuit using an op-amp (in inverting 03
configuration) to give output as bellow : (Consider value of 𝑅𝑓 = 2 𝑘Ω
& 𝑉1 , 𝑉2 , 𝑉3 are positive supplies)
𝑉𝑜𝑢𝑡 = − (𝑉1 + 𝑉2 + 𝑉3 )

(b) List out different types feedback configuration. Also Draw any two 04
block diagram representation of feedback configuration.

(c) In integrator circuit using op-amp, the value of 𝑅1 ∗ 𝐶𝐹 = 1 𝑠𝑒𝑐𝑜𝑛𝑑. 07

Now, input of a step (dc) voltage as shown in figure is applied to
circuit. Determine the output voltage and draw it. Assume that op-amp
is initially null.

OR
(c) In a differentiator circuit using op-amp, the value of 𝑅𝐹 = 07
1.5 𝑘Ω & 𝐶1 = 0.1 µ𝐹. Now, sine wave of 1 V peak at 1000 Hz is
applied to circuit. Determine the output voltage and draw it. Assume
that op-amp is initially null.
Q.3 (a) Explain positive clipper using op-amp with necessary figure & 03
waveform.
(b) Describe peaking amplifier using op-amp with necessary circuit & 04
waveform.
(c) Explain Schmitt trigger (inverting configuration) with input & output 07
waveform. Also derive the expression for hysteresis voltage.

1
 OR
Q.3 (a) Explain positive clamper using op-amp with necessary figure & 03
waveform.
(b) Describe currant to voltage converter using op-amp with necessary 04
circuit & equation.
(c) Explain 4 bit D/A converter with binary-weighted resistors with 07
necessary diagram. Also derive the expression for output voltage.

Q.4 (a) Draw circuit of wide band-pass filter using op-amp & narrow band 03
pass-filter using op-amp.
(b) Describe the scaling amplifier (inverting configuration) using op-amp 04
with deriving output voltage equation.
(c) Explain active first order low pass Butterworth filter with its transfer 07
function.
OR
Q.4 (a) Draw circuit of wide band-reject filter using op-amp & narrow band- 03
reject filter using op-amp.
(b) Describe the averaging amplifier(inverting configuration) using op- 04
amp with deriving output voltage equation.
(c) Explain active first order high pass Butterworth filter with its transfer 07
function.
Q.5 (a) Describe the 78XX series fixed voltage regulator. 03
(b) Explain phase shift oscillator with necessary diagram. 04
(c) Draw internal block diagram & timing waveform of monostable 07
multivibrator using 555 timer & explain each blocks in detail.

OR
Q.5 (a) Describe the LM317 series adjustable voltage regulator. 03
(b) Explain wien bridge oscillator with necessary diagram. 04
(c) Draw instrumentation amplifier using three op-amp with resistor 07
transducer bridge & derive the output voltage equation.

*************

2
Seat No.: ________ Enrolment No.___________

GUJARAT TECHNOLOGICAL UNIVERSITY

BE - SEMESTER– IV EXAMINATION – SUMMER 2020
Subject Code: 3141706 Date:26/10/2020
Subject Name: Analog Signal Processing
Time: 10:30 AM TO 01:00 PM Total Marks: 70
Instructions:
1. Attempt all questions.
2. Make suitable assumptions wherever necessary.
3. Figures to the right indicate full marks.

MARKS
Q.1 (a) Define Following terms: 03
1. CMRR
2. SVRR
3. Slew Rate
(b) Draw and explain in brief the internal block diagram of an 04
Op-Amp.
(c) Derive the equation of voltage gain of differential 07
amplifier using one Op-Amp (Closed loop configuration)
with its circuit diagram.

Q.2 (a) Draw and explain Voltage follower circuit using an Op- 03
Amp.
(b) Explain Bandwidth and Total output offset voltage for 04
Inverting Amplifier with feedback.
(c) Derive the equation of voltage gain of Non-Inverting 07
Summing amplifier using an Op-Amp with its circuit
diagram.
OR
(c) Draw and explain Voltage to Current converter with 07
floating load using an Op-Amp.
Q.3 (a) Explain Subtractor circuit using an Op-amp. 03
(b) Explain Zero Crossing detector circuit using an Op-Amp 04
with input/output waveforms.
(c) Explain Practical Differentiator circuit using an Op-Amp 07
with its circuit diagram. Frequency response, input/output
waveforms.
OR
Q.3 (a) Draw and Explain Voltage limiter circuit using an Op- 03
Amp.
(b) Draw and explain Sample and Hold circuit using an Op- 04
Amp.
(c) Draw Op-amp based full wave rectifier (absolute value 07
output) circuit. Explain its working with necessary
input/output waveforms.
Q.4 (a) Design + 5V power supply using 7805 with its circuit 03
diagram
(b) Explain adjustable voltage regulator using LM 317. 04

1
 (c) Explain Instrumentation Amplifier using three Op-Amp 07
Configuration and also derive the equation for the output
voltage.
OR
Q.4 (a) Explain Voltage controlled Oscillator (VCO) using IC 03
566.
(b) Draw and explain Square wave generator circuit using an 04
Op-Amp.
(c) Explain Successive Approximation type Analog to Digital 07

Q.5 (a) Explain All Pass filter. 03

(b) Draw and explain Programmable Gain Amplifier. 04
(c) Explain first order Low pass Butterworth Active filter 07
with circuit diagram and derivation of its transfer function.
OR
Q.5 (a) Explain Notch filter with its circuit diagram and necessary 03
waveforms.
(b) Explain Ramp Generator circuit using 555 timer in 04
Astable mode operation.
(c) Explain Monostable operation of 555 timer with its 07
internal block diagram with its output voltage and
capacitor voltage waveforms.

*************

2
 Seat No.: ________ Enrolment No.___________

GUJARAT TECHNOLOGICAL UNIVERSITY

BE- SEMESTER–IV (NEW) EXAMINATION – WINTER 2020
Subject Code:3141706 Date:09/02/2021
Subject Name:Analog Signal Processing
Time:02:30 PM TO 04:30 PM Total Marks:56
Instructions:
1. Attempt any FOUR questions out of EIGHT questions.
2. Make suitable assumptions wherever necessary.
3. Figures to the right indicate full marks.

Q.1 (a) Explain the following terms:

1) CMRR 02
2) Input Bias Current 01
(b) Define Input Offset Voltage and Slew Rate 04
(c) Describe the basic integrator circuit using opamp. Mention the problems 07
associated with the basic integrator and the methods to eliminate them. Also
derive the formula for fb and fa.

Q.2 (a) Explain the working of the I-V converter circuits with necessary derivations 03
(b) Explain the working of the V-I converter circuit with grounded load 04
with necessary derivations.
(c) Define Negative Feedback. Mention all the four basic configurations for negative 07
feedback. Describe opamp in voltage series configuration and derive the
expression for closed loop voltage gain.

Q.3 (a) Explain the working of Sample and Hold circuit with necessary diagrams. 03
(b) Explain positive and negative clampers with necessary diagrams. 04
(c) Explain the working of D/A converter with Binary weighted resistors. 07

Q.4 (a) Explain positive clippers with necessary diagrams. 03

(b) Explain the working of Schmitt Trigger circuits with necessary diagrams and 04
derivations.
(c) Explain the working of D/A converter with R-2R ladder network. 07

Q.5 (a) Define instrumentation amplifier. where it is used? 03

(b) Describe instrumentation amplifier using Resistive Transducer Bridge 04
(c) Explain the working of 555 timer in Monostable mode with necessary equations 07
and waveforms.

Q.6 (a) Explain Isolation amplifier. 03

(b) Explain Logarithmic amplifier. 04
(c) Explain the working of 555 timer as Astable multivibrator with necessary 07
equations and waveforms.
Q.7 (a) Give the necessary conditions for sustaining oscillations. 03
(b) Draw the circuit for Wein-Bridge oscillator and derive expression for output 04
frequency of oscillation.
(c) Describe 1st order active Butterworth low-pass filter and derive its transfer 07
function.
Q.8 (a) Explain the working of Notch Filter. 03
(b) Design a Narrow Band-Pass filter such that fc=1Khz, Q=3,Af =10. Assume the 04
value of capacitors to be 0.01uF.
(c) Explain Square wave generator using opamp. Using it, explain how we can 07
generate a triangular wave.

*************