Mi Robot Builder Rover

User Manual

This version is for private use only and should not be distributed.
Specifications
Name: Mi Robot Builder Rover Battery capacity: 18.3 Wh
Model: JMJQR03IQI Intelligent brick: Bluetooth
Materials: ABS, PC Wireless connectivity: Bluetooth 4.0
Number of pieces: 978 BLE operatingfrequency: 2402 MHz-2483 MHz
Weight: 2500 g Transmit power: 0 dbm
Dimensions: 380x320x95 mm 2.4G Radio frequency: 2402 MHz-2483 MHz
Age: 10 years+ Transmit power: 0 dbm
Input voltage: 14 V Storage temperature: -10°C~45°C
Input: 1.0 A Operating temperature: 0°C~55°C
Battery: Li - polymer

Motor 1 Intelligent brick Motor 2

Storage box Adapter

Building bricks Building instruction

01

This version is for private use only and should not be distributed.
Product Overview
1. Intelligent Brick

 Microphone
 Indicator
 Power Button
 Speaker
 Motor Ports
 Expansion Ports
 Pin Holes
 Reset Hole

2. Adapter
Use only the provided power adapter.

Ports А, В, C, D can be used for charging

Adapter Model: AD10002 Charging: Indicator light is red.

Input: 100 - 240 V ~ 50 / 60 Hz 0.5 A MAX Fully charged: Indicator light is off.
Output: 14V 1 A / 5V 1A The light is green when turning on the
intelligent brick.

02

This version is for private use only and should not be distributed.
3. Motor
Transmission shaft

Connectors

Assembling Mi Robot Builder Rover

1. Before you start
Put small bricks in the storage box, and large bricks in the bag.
2. Build your robot
Follow the building instruction or download the e-version from the Help in the Mi Robot
Builder app to assemble the bricks.
3. Inspectyour robot
Make sure the controller is fully charged when the robot is on its first use.
Make sure the motors are tightly connected with blocks.
Make sure you followed the building instruction when you were assembling your robot.

Turning on/off
Turning on: press the power button
Turning off: press and hold the power button for 3 seconds until you hear a sound prompt

03

This version is for private use only and should not be distributed.
Installing the app
1. Download the app
Scan the QR code below or go to App store to download and install "Mi Robot Builder".

2. Connecting your robot

Make sure your phone's Bluetooth is turned on. Open the Mi Robot Builder app and tap
the Bluetooth icon in the upper left corner to connectyour robot.

Bluetooth Help Settings

Connected
Battery 65%

3. Firmware updates and support

Make sure your phone is connected to the internet (preferably via Wi-Fi).
Open the app and connectyour robot, and then go to Settings > System updates >
Firmware updates.
It takes about 20 minutes to update the firmware.
Please note following:
• Make sure the motor is off during the updates. Otherwise, the parameters may be reset
and which may result in malfunction.
• Make sure the controller is fully charged before the update.
• Keep your phone away from the controller during the update.
• Refer to the "Help" in the app to learn more.

04

This version is for private use only and should not be distributed.
Precaution
• Do not disassemble the controller and the motor.
• Do not expose the product to sunlight, fire, heat or environments where temperature is
above 60°C (140°F).
• Do not short circuit the product in any way.
• Do not crush, puncture or strike the product.
• Children under 10 years old must be accompanied by adults while playing the product.
• Children under 3 years old must not use the product, as it contains small parts that can
cause suffocation.
• During charging, the battery must be placed in a well-ventilated area.
• Regularly check the charger for damages in the cord, plug, enclosure, and other parts.
If damage is detected, stop using the charger before it's repaired.
• Batteries are only to be charged by adults.

Declaration of Conformity
• We Beijing AIQI Technology Co., Ltd., hereby, declares that this equipment is in
compliance with the applicable Directives and European Norms, and amendments.
• WEEE Disposal and Recycling Information Correct Disposal of this product. This marking
indicates that this product should not be disposal with other household wastes
throughoutthe EU.
• To prevent possible harm to the environment or human health from uncontrolled waste
disposal, recycle it responsible to promote the sustainable reuse of materials resources.
To return your used device, please use the return and collection systems or contact the
retailer where the product was purchased. They can take this product for environmental
safe recycling.

Acceptable flexible cords for cord connected power units

Flexible cord type Maximum length, feet (m)
NISPT-2 2X18AWG 1.5 (m)

05

This version is for private use only and should not be distributed.
We declare that Toys is in compliance with the essential requirement and relevant
provisions of Directive 2009/48/EU.
Environmentally friendly disposal
Old electrical appliances must not be disposed of together with the residual waste, but
have to be disposed of separately. The disposal at the communal collecting point via
private persons is for free. The owner of old appliances is responsible to bring the
appliances to these collecting points or to similar collection points. With this little
personal effort, you contribute to recycle valuable raw materials and the treatment of
toxic substances.

Troubleshooting
Issues Possible reasons Solutions

Power button doesn't respond The controller's battery is low Charge the controller

The controller is off Turn the controller on

Can't connect via Bluetooth
Your phone's Bluetooth is off Turn on Bluetooth on your phone

Indicator lightturns red after Bluetooth disconnected Connect via Bluetooth again
a firmware upgrade and an error
sound prompt is played The controller's battery is low Charge the controller

Bluetooth disconnected Connect via Bluetooth again

The program doesn't run You haven't tapped the Play button Tap the Play button

You turned off the Programming mode Turn on Programming mode

The indicator light doesn't turn The power adapter isn't Connect the power adapter properly
red when charging connected properly
Read building instruction to make sure
The robot walks shakily The robot isn't assembled properly
you've assembled the robot properly

Can't use the app to control the robot Bluetooth disconnected Connect via Bluetooth again
You're using an incompatible
Can't charge Use a compatible power adapter
power adapter

Press the Reset button if you can't solve the issues using the solutions above.

06

This version is for private use only and should not be distributed.
 Read this manual carefully before use, and retain it for future reference.

Principal: Xiaomi Communications Со., Ltd.

Manufacturer: Beijing AIQI Technology Co., Ltd.
(a Mi Ecosystem Company)
Address: Room 1203, Block D, No. 9/11 Shangdi 3rd St., Haidian District, Beijing

07

This version is for private use only and should not be distributed.