G050VTN01.

■Preliminary Specifications
□Final Specifications

Module 5.0 Inch Color TFT-LCD

Model Name G050VTN01.0

24
3/
Customer Date Approved by Date

/0
14
20
Grace Hung 2013/12/16

On
ly
On
Checked &
Prepared by
Approved by
se
lU
na

Christine Huang 2013/12/16

er
nt
EI

Note: This Specification is subject to change Audio-Video Business Unit /

AS

without notice. AU Optronics corporation

IB
or
lF
tia
en
id
nf
Co
O
AU

G050VTN01.0 rev. 0.4

1/23

For IBASE Internal Use Only - Provided By stoneyshi On 2014/03/24

 G050VTN01.0

Contents
1. Operating Precautions ..................................................................................... 4
2. General Description ......................................................................................... 5
2.1 Display Characteristics ...................................................................................................... 5
2.2 Optical Characteristics ....................................................................................................... 6
3. Functional Block Diagram ............................................................................... 9
4. Absolute Maximum Ratings........................................................................... 10
4.1 Absolute Ratings of TFT LCD Module.............................................................................. 10
5. Electrical Characteristics............................................................................... 11
5.1 TFT LCD Module ............................................................................................................. 11
5.2 Backlight Unit ................................................................................................................... 13

24
6. Signal Characteristic...................................................................................... 14

3/
6.1 Pixel Format Image.......................................................................................................... 14

/0
6.2 Signal Description ............................................................................................................ 15

14
6.3 Interface Timing ............................................................................................................... 17

20
6.4 Power ON/OFF Sequence ............................................................................................... 19

On
7. Reliability Test Criteria................................................................................... 20
8. Mechanical Characteristics ........................................................................... 21

ly
8.1 LCM Outline Dimension ................................................................................................... 21

On
9. Label and Packaging...................................................................................... 22
se
9.1 Shipping Label (on the rear side of TFT-LCD display) ..................................................... 22
lU
9.2 Carton Package ............................................................................................................... 22
10 Safety.............................................................................................................. 23
na

10.1 Sharp Edge Requirements............................................................................................. 23

er

10.2 Materials ........................................................................................................................ 23

nt

10.3 Capacitors...................................................................................................................... 23
EI

10.4 National Test Lab Requirement...................................................................................... 23

AS
IB
or
lF
tia
en
id
nf
Co
O
AU

G050VTN01.0 rev. 0.4

2/23

For IBASE Internal Use Only - Provided By stoneyshi On 2014/03/24

 G050VTN01.0

Record of Revision

Version Date Page Old description New Description

V 0.1 All First Edition
V 0.2 6 Uniformity Condition: 5 Points Uniformity Conditions: 9 Points
Uniformity Max Value: 1.3 Delete Uniformity Max Value
7 Note 3: Uniformity 5 Points Note 3: Uniformity 9 Points
21 Thermal Cycle: -30 (1 hour) ~ 80 (1 hour), Thermal Cycle: -30 (30mins) ~ 80 (30
Total 50 cycles mins), Total 50 cycles
Ver 0.3 5 40 pins RGB 40 pins RGB (8-bits)
6 Response Time Delete Response time for Rising & Falling
only
9 Functional Block Diagram Update Functional Block Diagram

24
14 Pixel Format Image Update Pixel Format Image

3/
15~16 Pin assignment Pin assignment update

/0
17 Signal AC Characteristics Remove Hsync, Vsync

14
19 Power ON/OFF Sequence Remove Hsync, Vsync

20
21 LCM Outline dimension: TBD Add LCM Outline dimension 2D drawing

On
Ver 0.4 5 Real Outline Dimension: TBD Update Outline information
6 RGBW Chromaticity: TBD Update Simulation RGB Chromaticity

ly
20 RA Test criteria: THB & MTBF Add “ Power On” for THB & MTBF

On
21 LCM Outline Dimension Drawing Update Drawing

se
lU
na
er
nt
EI
AS
IB
or
lF
tia
en
id
nf
Co
O
AU

G050VTN01.0 rev. 0.4

3/23

For IBASE Internal Use Only - Provided By stoneyshi On 2014/03/24

 G050VTN01.0

1. Operating Precautions

1) Since front polarizer is easily damaged, please be cautious not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or soft cloth.
5) Since the panel is made of glass, it may be broken or cracked if dropped or bumped on hard
surface.
6) To avoid ESD (Electro Static Discharde) damage, be sure to ground yourself before handling
TFT-LCD Module.
7) Do not open nor modify the module assembly.

24
8) Do not press the reflector sheet at the back of the module to any direction.
9) In case if a module has to be put back into the packing container slot after it was taken out

3/
from the container, do not press the center of the LED Reflector edge. Instead, press at the

/0
far ends of the LED Reflector edge softly. Otherwise the TFT Module may be damaged.

14
10)At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the

20
Interface Connector of the TFT Module.

On
11)After installation of the TFT Module into an enclosure (Notebook PC Bezel, for example), do
not twist nor bend the TFT Module even momentary. At designing the enclosure, it should be

ly
taken into consideration that no bending/twisting forces are applied to the TFT Module from

On
outside. Otherwise the TFT Module may be damaged.
12)Small amount of materials having no flammability grade is used in the LCD module. The LCD
se
module should be supplied by power complied with requirements of Limited Power Source
lU
(IEC60950 or UL1950), or be applied exemption.
na

13)Severe temperature condition may result in different luminance, response time.

er

14)Continuous operating TFT-LCD Module under high temperature environment may accelerate
nt

LED light bar exhaustion and reduce luminance dramatically.

EI

15)The data on this specification sheet is applicable when LCD module is placed in landscape
AS

position.
IB

16)Continuous displaying fixed pattern may induce image sticking. It is recommended to use
or

screen saver or shuffle content periodically if fixed pattern is displayed on the screen.
lF
tia
en
id
nf
Co
O
AU

G050VTN01.0 rev. 0.4

4/23

For IBASE Internal Use Only - Provided By stoneyshi On 2014/03/24

 G050VTN01.0

2. General Description
This specification applies to the 5.0 inch color TFT LCD module G050VTN01.0.
G050VTN01.0 is built in timing controller and TTL interface. The screen format is intended to
support the WVGA (800(H) x 480(V)) screen and 16.2M (RGB 8-bits) G050VTN01.0 is a RoHS
product.

2.1 Display Characteristics

The following items are characteristics summary on the table under 25 ℃ condition:

Items Unit Specifications

24
Screen Diagonal [inch] 5.0

3/
Active Area [mm] 108.0(W) x 64.8(H)

/0
Pixels H x V 800 x 3(RGB) x 480

14
Pixel Pitch [mm] 0.135(W) x 0.135(H)

20
Pixel Arrangement R.G.B. Vertical Stripe

On
Display Mode TN, Normally White

ly
Nominal Input Voltage VDD [Volt] 3.3 typ.

On
LCD Typical Power Consumption [Watt] TBD

Back Light Power Consumption [Watt] 0.54 typ. se

lU
Weight [Grams] TBD
na

Physical Size [mm] 120.7(W) x 76.3(H)x 3.1(D)

er
nt

Electrical Interface 40 pins RGB 8-bits

EI

Surface Treatment Anti-glare, Hardness 3H

AS

Support Color 16.2M(8-bit with dithering)

IB

Temperature Range
or

o
Operating [ C] -20 to +70
o
Storage (Non-Operating) [ C] -30 to +80
lF

RoHS Compliance RoHS Compliance

tia

Viewing Direction 12 o’clock

en

Gray Scale Inversion Direction 6” o’clock

id
nf
Co
O
AU

G050VTN01.0 rev. 0.4

5/23

For IBASE Internal Use Only - Provided By stoneyshi On 2014/03/24

 G050VTN01.0

2.2 Optical Characteristics

The optical characteristics are measured under stable conditions at 25℃ (Room Temperature):
Item Unit Conditions Min. Typ. Max. Note
IF= 20mA
White Luminance [cd/m2] 260 350 - 1
(center point)
Uniformity % 9 Points 75% 80% 1.2.3

Contrast Ratio 500 600 - 4

Response Time [msec] Rising + Falling - 20 30

[degree] Horizontal (Right) 60 70 -

CR ≧ 10 (Left)

24
[degree]
60 70 -
Viewing Angle 6

3/
[degree] Vertical (Upper) 40 50 -

/0
[degree] CR ≧ 10 (Lower)
60 70 -

14
TBD TBD TBD
Red x

20
(0.606)

On
TBD TBD TBD
Red y
(0.323)

ly
On
TBD TBD TBD
Green x
(0.353)
Color / Chromaticity
TBD se
TBD TBD
lU
Coordinates Green y 1&7
(CIE 1931) (0.576)
na

TBD TBD TBD

er

Blue x
nt

(0.178)
EI

TBD TBD TBD

Blue y
AS

(0.123)
IB

White x 0.26 0.31 0.36

or

White y 0.28 0.33 0.38

lF

Color Gamut % - 50 - 1
tia

Note 7: RGBW Color Coordinates are based on the simulation result

en
id
nf
Co
O
AU

G050VTN01.0 rev. 0.4

6/23

For IBASE Internal Use Only - Provided By stoneyshi On 2014/03/24

 G050VTN01.0

Note 1: Measurement method

Equipment: Pattern Generator, Power Supply, Digital Voltmeter, Luminance meter (BM-5A or equivalent)
Scanning Direction : Normal Scan
Aperture 1∘with 50cm viewing distance
Test Point Center,
Environment < 1 lux

LCD Module
BM-5A or
equivalent

Measuring distance

24
3/
Module Driving Equipment

/0
14
Note 2: Definition of 9 points position (Display active area: 108.0(H) x 64.8(V)) mm

20
On
ly
On
se
lU
na
er
nt
EI
AS
IB

Note 3:
or

The luminance uniformity of 9 points is defined by dividing the maximum luminance value by the minimum
luminance value at full white condition.
lF

Minimum Brightness of nine points

tia

Uniformity (%) =
en
id
nf

Note 4： Definition of contrast ratio (CR):

Co

Brightness on the “White” state

O

Contrast ratio (CR)=

Brightness on the “Black” state
AU

G050VTN01.0 rev. 0.4

7/23

For IBASE Internal Use Only - Provided By stoneyshi On 2014/03/24

 G050VTN01.0

Note 5: Definition of response time:

The output signals of photo detector are measured when the input signals are changed from “White” to “Black”
(falling time) and from “Black” to “White” (rising time), respectively. The response time interval is between 10% and
90% of amplitudes. Please refer to the figure as below.

% Tf Tr

100
90
Optical
White Black White
response
10

24
0

3/
/0
14
Note 6: Definition of viewing angle

20
Viewing angle is the measurement of contrast ratio ≧10, at the screen center, over a 180° horizontal and 180°
vertical range (off-normal viewing angles). The 180° viewing angle range is broken down as below: 90° (θ)

On
horizontal left and right, and 90° (Φ) vertical high (up) and low (down). The measurement direction is typically
perpendicular to the display surface with the screen rotated to its center to develop the desired measurement

ly
On
viewing angle.

se
lU
na
er
nt
EI
AS
IB
or
lF
tia
en
id
nf
Co
O
AU

G050VTN01.0 rev. 0.4

8/23

For IBASE Internal Use Only - Provided By stoneyshi On 2014/03/24

 G050VTN01.0

3. Functional Block Diagram

The following diagram shows the functional block of the 5.0 inch color TFT/LCD module:

GATE

24
3/
/0
14
20
On
ly
On
se
lU
na
er
nt
EI
AS
IB
or
lF
tia
en
id
nf
Co
O
AU

G050VTN01.0 rev. 0.4

9/23

For IBASE Internal Use Only - Provided By stoneyshi On 2014/03/24

 G050VTN01.0

4. Absolute Maximum Ratings

4.1 Absolute Ratings of TFT LCD Module

Item Symbol Min Max Unit Conditions

LCD Drive Voltage VDD -0.3 +5 [Volt]

Input signal Voltage Vin -0.3 +5 [Volt]

24
3/
/0
14
20
On
ly
On
se
lU
na
er
nt
EI
AS
IB
or
lF
tia
en
id
nf
Co
O
AU

G050VTN01.0 rev. 0.4

10/23

For IBASE Internal Use Only - Provided By stoneyshi On 2014/03/24

 G050VTN01.0

5. Electrical Characteristics
5.1 TFT LCD Module
5.1.1 Power Specification

Symbol Parameter Min Typ Max Units Remark

Logic/LCD Drive ±10%
VDD Voltage
3.0 3.3 3.6 [Volt]
All Black Pattern
IVDD VDD Current - TBD TBD [mA]
(VDD=3.3V, at 60Hz)
All Black Pattern
PVDD VDD Power - TBD TBD [Watt]
(VDD=3.3V, at 60Hz)
Note 1

24
Irush LCD Inrush Current - - TBD [A]

3/
/0
Note 1: Measurement condition:

14
20
90% 3.3V

On
10%

ly
0V

On
0.5ms

se
lU
VDD rising time
na
er
nt
EI
AS
IB
or
lF
tia
en
id
nf
Co
O
AU

G050VTN01.0 rev. 0.4

11/23

For IBASE Internal Use Only - Provided By stoneyshi On 2014/03/24

 G050VTN01.0

5.1.2 Signal Electrical Characteristics

Input signals shall be low or Hi-Z state when VDD is off.

Parameter Symbol Min. Typ. Max. Unit Remarks

Logic Input Voltage for High VIH 0.7VDD - VDD Volt

Display Signals Low VIL 0 - 0.3VDD Volt

24
3/
/0
14
20
On
ly
On
se
lU
na
er
nt
EI
AS
IB
or
lF
tia
en
id
nf
Co
O
AU

G050VTN01.0 rev. 0.4

12/23

For IBASE Internal Use Only - Provided By stoneyshi On 2014/03/24

 G050VTN01.0

5.2 Backlight Unit

5.2.1 Parameter guideline for LED
Following characteristics are measured under a stable condition using an inverter at 25℃ (Room Temperature):The
backlight (LED module, Note 1) is suggested to drive by constant current 140mA.

Parameter Symbol Min. Typ. Max. Unit Remark

LED light bar Voltage VL 8.4 9 9.9 V
Current of Each LED ILED 20 mA
Power Consumption PBL 0.504 0.540 0.594 W Note 1
LED Life Time LL 20,000 -- -- Hr Note 2

Note 1: The LED driving condition is defined for LED module (9 LED). The voltage range will be up to 9.9V based

24
on suggested driving current set as 60mA.

3/
/0
14
20
On
ly
On
Note 2: Define “LED Lifetime”: brightness is decreased to 50% of the initial value. LED Lifetime is restricted under
normal condition, ambient temperature = 25℃ . se
lU
na
er
nt
EI
AS
IB
or
lF
tia
en
id
nf
Co
O
AU

G050VTN01.0 rev. 0.4

13/23

For IBASE Internal Use Only - Provided By stoneyshi On 2014/03/24

 G050VTN01.0

6. Signal Characteristic
6.1 Pixel Format Image
Following figure shows the relationship between input signal and LCD pixel format.

R G B … … … … … … … … … … … … . R G B

… … … … …
R G B
… … …
… … …

24
3/
/0
R G B … … … … … … … … … … … … . R G B

14
20
(1 2 3… .… … … … . 2398 2399 2400)

On
ly
On
se
lU
na
er
nt
EI
AS
IB
or
lF
tia
en
id
nf
Co
O
AU

G050VTN01.0 rev. 0.4

14/23

For IBASE Internal Use Only - Provided By stoneyshi On 2014/03/24

 G050VTN01.0

6.2 Signal Description

The connector pin definition is as below.

Pin No. Symbol I/O Description

1 VLED- P Black light for cathode

2 VLED+ P Back light for anode

3 VDD P Power supply

4 GND G Ground
Stand by mode. (Internal pull low)
STBYB=“1”: Normally operation.
5 Display_EN I STBYB=“0”: Standby mode. Timing controller, source driver will

24
turn off, all output are High-Z

3/
6 R0 I Red Data input (LSB)

/0
7 R1 I Red Data input

14
8 R2 I Red Data input

20
9 R3 I Red Data input
GND G Ground

On
10
11 R4 I Red Data input

ly
12 R5 I Red Data input

On
13 R6 I Red Data input

14 R7 I Red Data input (MSB)

GND G Ground se
lU
15
16 G0 I Green Data input (LSB)
na

17 G1 I Green Data input

er

18 G2 I Green Data input

nt

19 G3 I Green Data input

EI

20 GND G Ground
AS

21 G4 I Green Data input

IB

22 G5 I Green Data input

or

23 G6 I Green Data input

lF

24 G7 I Green Data input (MSB)

tia

25 GND G Ground
en

26 B0 I Blue Data input (LSB)

id

27 B1 I Blue Data input

nf

28 B2 I Blue Data input

Co

29 B3 I Blue Data input

O

30 GND G Ground
AU

31 B4 I Blue Data input

G050VTN01.0 rev. 0.4

15/23

For IBASE Internal Use Only - Provided By stoneyshi On 2014/03/24

 G050VTN01.0

32 B5 I Blue Data input

33 B6 I Blue Data input
34 B7 I Blue Data input (MSB)
35 GND G Ground

36 DCLK I Clock for input data. Data latched at falling edge of this signal.

37 GND G Ground
Data input enable. Active high to enable the data input bus under
38 DE I
“DE Mode “.
39 HSYNC I Horizontal sync input (Only use DE mode, please pull low)

40 VSYNC I Vertical sync input (Only use DE mode, please pull low)

Note1 : I/O Definition, I = Input, P = Power, G = Ground.

24
Note2 : “Low” stands for 0V. “High” stands for 3.3V.

3/
/0
14
20
On
ly
On
se
lU
na
er
nt
EI
AS
IB
or
lF
tia
en
id
nf
Co
O
AU

G050VTN01.0 rev. 0.4

16/23

For IBASE Internal Use Only - Provided By stoneyshi On 2014/03/24

 G050VTN01.0

6.3 Interface Timing

6.3.1 Signal AC Characteristics
Parameter Symbol Min. Typ. Max. Unit Remark
DCLK duty cycle D cw 40 50 60 % tcw / tDCLK x100%
Data Setup Time tdst 12 -- -- ns
Data Hold Time tdhd 12 -- -- ns
DE Setup Time tdest 12 -- -- ns
DE Hold Time tdehd 12 -- -- ns

24
3/
/0
14
20
On
ly
On
se
lU
na
er
nt
EI
AS
IB
or
lF
tia
en
id
nf
Co
O
AU

G050VTN01.0 rev. 0.4

17/23

For IBASE Internal Use Only - Provided By stoneyshi On 2014/03/24

 G050VTN01.0

6.3.2 Input Timing Characteristics

DE mode
Parameter Symbol Min. Typ. Max. Unit. Remark

DCLK Frequency 1/tDCLK 25 30 36 MHz

Frame Rate Frequency 55 60 65 Hz
Cycle tv 484 525 735 tH
1 Frame
Display Period tvd 480 tH
Scanning Time
Blanking tvbl 4 45 255 tH
Cycle tH 885 928 1312 tDCLK
1 Line Scanning
Display Period thd 800 tDCLK
Time
Blanking thbl 85 128 512 tDCLK

24
Vertical timing (DE mode):

3/
/0
14
20
On
ly
On
Horizontal timing (DE mode):

se
lU
na
er
nt
EI
AS
IB
or
lF
tia
en
id
nf
Co
O
AU

G050VTN01.0 rev. 0.4

18/23

For IBASE Internal Use Only - Provided By stoneyshi On 2014/03/24

 G050VTN01.0

6.4 Power ON/OFF Sequence

VDD power and backlight on/off sequence is as below. Interface signals are also shown in the chart. Signals from any
system shall be Hi-Z state or low level when VDD is off.

24
3/
The above on/off sequence should be applied to avoid abnormal function in the display. Please make sure to turn off

/0
the power when you plug the cable into the input connector or pull the cable out of the connector.

14
20
On
ly
On
se
lU
na
er
nt
EI
AS
IB
or
lF
tia
en
id
nf
Co
O
AU

G050VTN01.0 rev. 0.4

19/23

For IBASE Internal Use Only - Provided By stoneyshi On 2014/03/24

 G050VTN01.0

7. Reliability Test Criteria

Items Required Condition Note

Temperature
Humidity Bias 60℃/90%,240 hours, Power On
High Temperature
Operation 70℃,240 hours
Low Temperature
Operation -20℃,240 hours
Hot Storage 80℃,240 hours
Cold Storage -30℃,240 hours
Thermal Cycle -30℃(30mins)<- -> + 80 ℃(30 mins) Total 50 Cycles

24
Shock Test
(Non-Operating) 60G,6ms, 3 times for each direction

3/
Frequency Range : 10 ~ 55 Hz

/0
Vibration Test
(Non-Operating) Stroke : 1.5mm Sweep : 10 Hz ~ 55 Hz ~ 10 Hz

14
2 hours for each direction of X, Y, Z(6 hours of total)

20
Acceleration :2.0G
Vibration Test

On
(Packaging Box) Frequency Range : 10 ~ 100 Hz
2 hours for each direction of X, Y, Z.(6 hours of total)

ly
On/off test On/10 sec, Off/10 sec, 30,000 cycles

On
Height: 750mm

Drop Test
Drop test must be done 6 times
se
lU
Once corner each time
na

One flat sides each time

er

MTBF sample qty 10 pcs, 504s Hrs, 60 ℃ 90% RH, Power On

nt
EI

Contact Discharge: ± 4KV, 150pF(330Ω )

ESD Air Discharge: ± 8KV, 150pF(330Ω ) Note 1
AS

6 times at each test point

IB
or

Note1: According to EN61000-4-2, ESD class B: Some performance degradation allowed. No data lost
lF

. Self-recoverable. No hardware failures.

tia
en
id
nf
Co
O
AU

G050VTN01.0 rev. 0.4

20/23

For IBASE Internal Use Only - Provided By stoneyshi On 2014/03/24

 G050VTN01.0

8. Mechanical Characteristics
8.1 LCM Outline Dimension

24
3/
/0
14
20
On
ly
On
se
lU
na
er
nt
EI
AS
IB
or
lF
tia
en
id
nf
Co
O
AU

G050VTN01.0 rev. 0.4

21/23

For IBASE Internal Use Only - Provided By stoneyshi On 2014/03/24

 G050VTN01.0

9. Label and Packaging

9.1 Shipping Label (on the rear side of TFT-LCD display)

G050VTN01.0
G070VTN01.0

24
9.2 Carton Package

3/
/0
14
20
On
ly
On
se
lU
na
er

(25+1)trays
nt
EI

6 pcs/tray
AS

(25+1)trays/carton
IB

Total 150 pcs panel/carton

or

Carton size:520*340*250mm
lF

Total Weight：TBD
tia
en
id
nf
Co
O
AU

G050VTN01.0 rev. 0.4

22/23

For IBASE Internal Use Only - Provided By stoneyshi On 2014/03/24

 G050VTN01.0

10 Safety

10.1 Sharp Edge Requirements

There will be no sharp edges or corners on the display assembly that could cause injury.

10.2 Materials
10.2.1 Toxicity
There will be no carcinogenic materials used anywhere in the display module. If toxic materials are
used, they will be reviewed and approved by the responsible AUO toxicologist.
10.2.2 Flammability

24
All components including electrical components that do not meet the flammability grade UL94-V1 in the

3/
module will complete the flammability rating exception approval process.

/0
The pRxINted circuit board will be made from material rated 94-V1 or better. The actual UL

14
flammability rating will be pRxINted on the pRxINted circuit board.

20
10.3 Capacitors

On
If any polarized capacitors are used in the display assembly, provisions will be made to keep them from

ly
being inserted backwards.

On
10.4 National Test Lab Requirement
The display module will satisfy all requirements for compliance to: se
lU
na

UL 1950, First Edition U.S.A. Information Technology Equipment

er
nt
EI
AS
IB
or
lF
tia
en
id
nf
Co
O
AU

G050VTN01.0 rev. 0.4

23/23

For IBASE Internal Use Only - Provided By stoneyshi On 2014/03/24