Controlled Form MAA.

MTO-QP13F-50

Basic Practical Training Logbook

B1.1
About this document

This logbook is supported by EASA and Mid-East Aviation Academy MAA It provides the recommended means of recording basic practical maintenance training in order to
support an application to the authority for the issue or variation of an Aircraft Maintenance License in accordance with EASA Part-66 and related guidance. Its structure guides the
applicant's recordings in view of a quick and accurate assessment of his/ her training and technical knowledge. In order to make it a widely used reference, this document provides evidence
of practical Training gained on the mentioned aircraft/ Workshop / category/module.

Family & first name:

Nationality: Date of Birth:

Full address:

License Category applied for (EASA Form…) your category is B1.1 The required tasks for the encircled category have
Been performed and assessed where appropriate.
Name and signature of approved Assessor
Logbook Owner’s Signature:

Date:

Issue (1) Feb.2020 Revision: 01 Page 1 of1 2

 Controlled Form MAA.MTO-QP13F-50

General Information
1. All entries in this logbook shall be made in ink.
2. When used in support of an application for a license, any false entry in the logbook will constitute a legal offence.
3. Entries in the logbook shall be made personally by the logbook holder and confirmed / certified by an authorised person
(e.g., instructor or assessor, Part-147, -145, authorised person).
Completion of the Log pages: The log pages of this book have the following general format:
Part 66 License Category A/C Registration Date
Index ATA Task/ Competence Instructor / Assessor and Company
Module B1.1 or Workshop (ddmmyy)

The following information and instruction for each column shall be observed:

Index Numbering of the items for easy reference

ATA chapter Reference to ATA 100 classification
Task/ Competence: Describes the task to be performed or competence to be obtained. The tasks identified in this section are agreed between
EASA and MAA, to satisfy EASA Part66 basic practical knowledge and experience requirements. The training and assessment may be carried
out on in-service aircraft in workshops, on training equipment or on simulators I.A.W. the attached assessment forms License Category the
references in this column indicate for which license category the task / competence described is required. Circle the license category for which
your basic training is intended in the header of each page.
A/C Registration or The entries made in this column state where the task has been performed, to allow traceability, In case of extensive work, it
may be Workshop: useful to add a detailed work report to the logbook folder.
Instructor/Assessor and Company
Each entry must be signed by an instructor/assessor, with full name and organization, to certify that the logbook owner has achieved the
required competence on the subject or that the task has been carried out correctly under his supervision I.A.W. the attached assessment
forms.

Date: Indicates the date of closure/certifying by the authorized person.

Issue (1) Feb.2020 Revision: 01 Page 2 of 12

 Controlled Form MAA.MTO-QP13F-50

Index ATA Part-66 License A/C Registry Inst.

Task / competence Category Hrs. Date
No. Chapter Module or Workshop Name
B1.1
Mod 3
1. --- 3.6 Using the multimeter B1.1 Av.workshop1 3
2. ---- 3.6 Use test meters to measure - (voltage). B1.1 Av.workshop1 3
3. ---- 3.6 Use test meters to measure - (current). B1.1 Av.workshop1 3
4. ---- 3.7 Measuring Resistance characteristics B1.1 Av.workshop1 3
5. ---- 3.7 Voltage characteristics of short and an open B1.1 Av.workshop1 3
6. ---- 3.7 Bridge circuit B1.1 Av.workshop1 3
7. ---- 3.9 Series and parallel capacitors B1.1 Av.workshop1 3
8. ---- 3.13 How to use the oscilloscope B1.1 Av.workshop1 3
9. ----- 3.14 (LC- filter circuit). B1.1 Av.workshop1 3
10. ---- 3.15 (Transformer - characteristics). B1.1 Av.workshop1 3
Total = 30
Mod 4Electronic fundamentals
11. ---- 4.1 Use test meter to check the Diode Characteristics B1.1 Av.workshop1 2
12. ---- 4.1 Diode application As Rectifier B1.1 Av.workshop1 2
13. ---- 4.1 Zener-diode as regulator B1.1 Av.workshop1 2
Use test meter to check /test the bipolar (NPN) and
14. ---- 4.1
(PNP)transistor
B1.1 Av.workshop1 2
15. ---- 4.1 SCR –Testing &function B1.1 Av. workshop1 2
Total = 10
Mod 5Digital Techniques /Electronic Instrument System (M5)
16. ---- 5.1 Aircraft basic classic T instrument exploitation B1.1 B737-200 2
Use the electronics lab to apply logic gates and perform the
17. ---- 5.5
following experiments: basic logic gates experiments and, or, not
B1.1 Av.Workshop1 3
Use the electronics lab to apply logic gates and perform the following
18. ---- 5.5 experiments: basic logic gates experiments NAND, NOR, and XOR B1.1 Av.Workshop1 3
Characteristics
19. ----- 5.6 Identify basic computer structure components B1.1 Av.Workshop1 2
Total = 10

Issue (1) Feb.2020 Revision: 01 Page 3 of 12

 Controlled Form MAA.MTO-QP13F-50

Module 7 Maintenance Practice

Practice safety precautions when working with fluids, gasses and
20. ---- 7.1
chemicals
B1.1 Paint & welding shop 2
Identify hazards and demonstrate safe working practices when
21. ---- 7.1
working on aircraft
B1.1 B737-200 2
22. ---- 7.2 Apply safety practices in work shop environment. B1.1 Airframe & general shop 2
23. ---- 7.2 Define proper care and control of tools and equipment. B1.1 Airframe & general shop 1
Using measuring equipment to check the size allowance, fit and
24. ---- 7.2
clearance on landing gear selector valve quadrant assembly
B1.1 B737-200 2
Use of measuring equipment e.g., Micrometers and Vernier
25. ---- 7.3
caliper
B1.1 Airframe & general shop 2
Proper Selecting and Use of Drilling, Reaming and Thread
26. ---- 7.3
Cutting Tool
B1.1 Airframe & general shop 2
27. ---- 7.3 The proper use of different types of files on metal sheets B1.1 Airframe & general shop 4
28. ---- 7.3 Identify tools and equipment B1.1 Airframe & general shop 2
29. ---- 7.3 Use the different types of Callipers and Dividers B1.1 Airframe & general shop 2
Use taps and dies to cut internal threads (in a drilled
30. ---- 7.3
hole)/external thread (on a metallic rod/shaft)
B1.1 Airframe & general shop 2
31. ---- 7.3 Use a torque meter with & without extension B1.1 Airframe & general shop 2
32. ---- 7.3 Drilling and reaming a hole in sheet metal B1.1 Sheetmetal shop 2
33. 34 7.4 Pitot static system - description and operation B1.1 B737-200 2
34. ------ 7.4 Use test meters to measure current B1.1 Avworkshop1 2
35. ------ 7.4 Use Test Meters (analogue meter) To Measure Resistance B1.1 Avworkshop1 2
36. ----- 7.4 Use Test Meters (analogue meter) To Measure Volts B1.1 Avworkshop1 1
Check an aircraft electrical circuit for continuity in conjunction
37. 20 7.4
with an electrical wiring diagram
B1.1 B737-200 2
Carry-out basic fault-finding techniques using range of test
38. ------ 7.4
meters (short or open)
B1.1 Avworkshop1 2
39. ---- 7.4 Test procedures for electrical bonds B1.1 B737-200 2
40. ---- 7.4 Carry out insulation test B1.1 B737-200 2
Demonstrate the correct use of a maintenance manual in Wheel B737-200
41. 7.5
and Breaks removal/installation
B1.1 2
42. ---- 7.5 Identify nose landing gear by using Illustrated Parts Catalog(IPC) B1.1 B737-200 2

Issue (1) Feb.2020 Revision: 01 Page 4 of 12

 Controlled Form MAA.MTO-QP13F-50

43. ---- 7.6 Demonstrate / explain use of feeler gauge B1.1 B737-200 2
Drill and ream perpendicular holes in ferrous and non-ferrous
44. ---- 7.6
material
B1.1 Sheetmetal shop 2
45. ---- 7.6 Drill and tap a threaded hole B1.1 Sheetmetal shop 2
46. ---- 7.6 Fit and remove thread inserts B1.1 Sheetmetal shop 2
47. ------ 7.7 Perform wire splicing B1.1 Av. Workshop 1 3
48. ------ 7.7 Using crimping tool to insert terminal lug or splices. B1.1 Av. Workshop 1 3
49. 7.7 Carry out pre –use checks of digital multi-meter B1.1 Av. Workshop1 3
To check wires continuity in looms or connector using multi-
50. ------ 7.7
meter.
B1.1 Av. Workshop 1 3
Extract electrical inserts (pins) in a variety of electrical
51. 20 7.7
connectors
B1.1 Av. Workshop 1 3
52. 20 7.7 Insert electrical inserts(pins)in electrical connectors B1.1 Av. Workshop 1 3
Contact crimping& insert/ extract electrical inserts (pins) in
53. ------ 7.7
electrical connectors
B1.1 Av. Workshop 1 4
54. Reserved
Inspect Electrical Cable Looms and Bundles condition And
55. 20 7.7
Correct Them If Necessary
B1.1 B737-200 2
56. ----- 7.7 Install Heat Shrink Sleeves in Cables B1.1 Av. Workshop 1 4
57. 20 7.7 Installation of split sleeve for protection of a wire harness B1.1 Av. Workshop 1 2
58. 20 7.7 Replacement of a Damaged Cable. B1.1 Av. Workshop 1 4
59. ----- 7.7 Install wiring clamp B1.1 Av. Workshop 1 2
60. ----- 7.7 Continuity Checking for wires and circuit B1.1 Av. Workshop 1 4
Interpret typical electrical wiring diagrams and schematics
61. ----- 7.7
circuits
B1.1 Av. Workshop 1 3
62. 20 7.7 Repair or replace an electrical connector locking wire. B1.1 Av. Workshop 1 2
63. ----- 7.7 Wire stripping for soldering B1.1 Av. Workshop 1 2
64. ----- 7.7 Joining Wires Together with Solder B1.1 Av. Workshop 1 3
Use pneumatic drill & tools to perform riveting holes in sheet
65. ---- 7.8
metal
B1.1 Sheetmetal shop 3
66. ---- 7.8 Identify arrange of solid and blind rivets and fasteners B1.1 Sheetmetal shop 2
67. ---- 7.8 Perform Patch repair on a metal sheet B1.1 Sheetmetal shop 8
68. ---- 7.8 Install universal and countersunk rivets in aluminum sheet using B1.1 Sheetmetal shop 4

Issue (1) Feb.2020 Revision: 01 Page 5 of 12

 Controlled Form MAA.MTO-QP13F-50

various methods
69. ---- 7.8 Riveting inspection for improper forming (defective) B1.1 Sheetmetal shop 1
70. ---- 7.8 Remove defective rivets without causing further damage to skin B1.1 Sheetmetal shop 4
71. ---- 7.9 Bending a rigid pipe B1.1 Sheetmetal shop 2
72. ---- 7.9 Flaring rigid pipe B1.1 Sheetmetal shop 2
73. ---- 7.10 Visual inspection of springs condition B1.1 Sheetmetal shop 2
74. ---- 7.11 Inspection of Ball/Roller Bearings B1.1 Sheetmetal shop 2
75. ---- 7.11 Lubricate aircraft main landing gear B1.1 Sheetmetal shop 2
Chain visually inspection for cracks, wear, corrosion, damage,
76. ---- 7.12
twist
B1.1 Sheetmetal shop 2
77. ---- 7.13 Visual inspection of control cable systems and pulleys B1.1 Sheetmetal shop 2
78. ---- 7.14 Bending metal sheet using bend bar B1.1 Sheetmetal shop 2
79. ---- 7.14 Sheet metal cutting B1.1 Sheetmetal shop 3
80. ---- 7.14 Cutting, drilling, reaming and thread cutting metal sheet B1.1 Sheetmetal shop 5
81. ---- 7.14 Practice the correct procedure when using hacksaw B1.1 Sheetmetal shop 2
82. ---- 7.14 Smoothing metal edges by using file or grinder B1.1 Sheetmetal shop 2
83. ---- 7.15 Perform welding / Soldering B1.1 Paint &Welding shop 2
84. ---- 7.15 Perform bonding method B1.1 Sheetmetal shop 3
85. Reserved
86. ---- 7.16 Prepare aircraft for weighing B1.1 A/C Sama 4
87. ---- 7.17 Aircraft jacking B1.1 A/C Sama 6
88. ---- 7.17 Park, chock and grounding the aircraft B1.1 A/C Sama 4
89. ---- 7.17 Perform long time parking B1.1 A/C Sama 4
90. ---- 7.17 Aircraft towing B1.1 A/C Sama 2
91. ---- 7.17 Aircraft refueling \defueling B1.1 A/C Sama 4
92. --- 7.17 Hydraulic ground servicing filter Removal / installation B1.1 B737-200 3
93. 12 7.17 Perform lubrication of bearing (flight control /landing gear) B1.1 B737-200 3
94. 54 7.17 Engine-to-wing forward fairing - removal/installation B1.1 B737-200 3
95. 36 7.17 Remove and install ducts and clamps B1.1 B737-200 3
96. ---- 7.18 Adjust, Set and Use Torque for Tightening of Bolts B1.1 B737-200 1
Identify part and serial numbers from a component overhaul
97. 56 7.18
manual or IPC
B1.1 B737-200 1

Issue (1) Feb.2020 Revision: 01 Page 6 of 12

 Controlled Form MAA.MTO-QP13F-50

98. 20 7.18 Lock Wire–removal and installation B1.1 Airframe & general shop 1
Measure shafts, bores, and adjacent surfaces using precision
99. ---- 7.18
measuring instruments
B1.1 Sheetmetal shop 2
100. 74 7.18 Inspect engine using borescope B1.1 Engine shop 2 2
101. 5 7.18 Visual Dimension Inspections for Tires, Wheels B1.1 Airframe shop 2 1
Hard landing or high drag / side load landing condition
102. 5 7.19
inspection
B1.1 B737-200 2
Explain the required inspection following a lightning strike or
103. 5 7.19
static discharges
B1.1 B737-200 2
104. ---- 7.20 Perform the procedure for material storage B1.1 MAA Store 2
105. 71 7.20 Perform 50 hrs inspection B1.1 A/C Sama 6
Total = 215
Module 11
106. 27 11.1 Flight control description B1.1 B737-200 3
107. 27 11.1 Aileron balance tab – removal installation B1.1 Airframe shop 2 3
108. 52 11.2 Galley servicing door insp. B1.1 B737-200 3
109. 52 11.2 Tire burst protector - removal/installation B1.1 B737-200 3
110. 52 11.3 Inspection /check of cargo compartment doors B1.1 B737-200 2
111. 25 11.3 1st observers seat removal /installation B1.1 B737-200 2
112. 21 11.4 Air mix valve - removal/installation B1.1 B737-200 3
113. 21 11.4 Modulating and shutoff valve - Removal/Installation B1.1 B737-200 3
114. 21 11.4 Pressure regulator - Removal/Installation B1.1 B737-200 2
115. 21 11.4 Air cleaner purge valve - Removal/Installation B1.1 B737-200 3
116. 21 11.4 Air cycle machine (ACM) - removal/installation B1.1 B737-200 12
117. 21 11.4 Water separator - removal/installation B1.1 B737-200 3
118. 34 11.5 Air Data computers removal /installation B1.1 B737-200 2
119. 23 11.5 HF communication description B1.1 B737-200 3
120. 23 11.5 Vhf antenna removal/installation B1.1 B737-200 3
121. 23 11.5 VHF communication systems - description and operation B1.1 B737-200 3
122. 34 11.5 VHF NAV control panel - removal/installation B1.1 B737-200 3
123. 34 11.5 GPWS control module - removal/installation B1.1 B737-200 2

Issue (1) Feb.2020 Revision: 01 Page 7 of 12

 Controlled Form MAA.MTO-QP13F-50

124. 23 11.5 Voice recorder Control unit - removal/installation B1.1 B737-200 3

125. 23 11.5 Flight recorder - removal/installation B1.1 B737-200 3
126. 34 11.5 Directional gyro Removal & insulation B1.1 B737-200 3
127. 34 11.5 Total air temperature probe - removal/installation B1.1 B737-200 4
128. 34 11.5 Pitot -static probes cleaning B1.1 B737-200 3
129. 34 11.5 Total air temperature probe test B1.1 B737-200 3
130. 34 11.5 Voice recorder unit removal & installation B1.1 B737-200 3
131. 24 11.6 Manual control - maintenance practices (apply power) B1.1 B737-200 5
132. 24 11.6 Electrical power (description) B1.1 B737-200 4
133. 24 11.6 Transformer rectifier unit removal/Installation B1.1 B737-200 6
134. 24 11.6 D.C – generation sys. (description) B1.1 B737-200 4
135. 24 11.6 Remove / installation of Main storage Batteries B1.1 B737-200 5
136. 24 11.6 Generator drive and standby power Module (ps-5) Rem./Inst. B1.1 B737-200 5
137. 24 11.6 Current Transformer Removal /Installation B1.1 B737-200 5
138. 24 11.6 Generator control unit - removal/installation B1.1 B737-200 6
139. 25 11.7 Window shades - removal/installation B1.1 B737-200 4
140. 25 11.7 Window panels - removal/installation B1.1 B737-200 4
141. 26 11.8 Test the Fire Detection Elements B1.1 B737-200 4
142. 26 11.8 Operational Test of the Engine Fire Detection System B1.1 B737-200 3
143. 27 11.9 Flight controls hydraulic modular package – Rem./Inst. B1.1 B737-200 4
144. 27 11.9 Flight control shut off valve and valve motor Rem./Inst B1.1 B737-200 4
145. 27 11.9 Leading edge flap flow limiting valve Rem./Inst. B1.1 B737-200 2
146. 27 11.9 Standby rudder actuator shut off valve B1.1 B737-200 3
147. 27 11.9 Control column shaker rem. / inst. B1.1 B737-200 2
148. 28 11.10 Description for fuel system B1.1 B737-200 2
149. 28 11.10 Fuel Booster Pump– removal installation B1.1 B737-200 3
150. 28 11.10 Fueling manifold Rem./Inst. B1.1 B737-200 3
151. 28 11.10 Fuel shut off valve Rem. / Inst. B1.1 B737-200 3
152. 28 11.10 Remove/install fuel receptacle B1.1 B737-200 3
153. 28 11.10 Using fuel measuring stick B1.1 B737-200 1

Issue (1) Feb.2020 Revision: 01 Page 8 of 12

 Controlled Form MAA.MTO-QP13F-50

154. 28 11.10 De fueling Valve Rem./Inst. B1.1 B737-200 8

155. 29 11.11 Ground servicing hand pump Rem./Inst. B1.1 B737-200 4
156. 29 11.11 Hyd. Ground servicing filter Rem./Inst. B1.1 B737-200 3
157. 29 11.11 Hyd. Reservoir pressurization relief valve Rem./Inst. B1.1 B737-200 3
158. 29 11.11 Hyd. System (A) check valves - Rem./Inst. B1.1 B737-200 3
159. 29 11.11 System a hydraulic pump case drain filter - Rem./Inst. B1.1 B737-200 2
160. 29 11.11 System (A) hyd. Return filter Rem./Inst. B1.1 B737-200 2
161. 29 11.11 System (B) pressure relief valve Rem./Inst. B1.1 B737-200 3
162. 30 11.12 Wing thermal anti- icing shut off valve Rem./Inst. B1.1 B737-200 3
163. 30 11.12 Wind shield wiper assembly Rem./Inst. B1.1 B737-200 2
164. 30 11.12 Remove wind shield wiper blade B1.1 B737-200 2
165. 32 11.13 Disassembly and reassembly of multi disc brake B1.1 Airframe shop 2 8
166. 32 11.13 Main gear damper - Removal/Installation B1.1 Airframe shop 2 6
167. 32 11.13 Nose gear torsion link –removal/installation B1.1 Airframe shop 2 2
168. 32 11.13 Inspection/check main landing gear tire/wheel B1.1 B737-200 2
169. 32 11.13 Build up main landing gear wheel B1.1 Airframe shop 2 6
170. 32 11.13 Landing Gear Brake- removal/ installation B1.1 Airframe shop 2 3
171. 32 11.13 Autobrake shuttle valve - removal/installation B1.1 B737-200 2
172. 32 11.13 Antiskid valve - removal/installation B1.1 B737-200 3
173. 32 11.13 Main gear wheel well blade-type seal – Rem./Inst. B1.1 B737-200 2
174. 33 11.14 Landing and runway turnoff lights - description and operation B1.1 B737-200 3
175. 33 11.14 Lower beacon light - removal/installation B1.1 B737-200 3
176. 33 11.14 Ceiling light ballast - removal/installation B1.1 B737-200 3
177. 33 11.14 Ceiling mounted exit sign - removal/installation B1.1 B737-200 3
178. 12 11.15 Remove And Install Oxygen Cylinder B1.1 B737-200 3
179. 35 11.15 Crew oxygen pressure reducing regulator - Rem./Inst. B1.1 B737-200 3
180. 35 11.15 Passenger oxygen continuous flow control unit - Rem./Inst. B1.1 B737-200 4
181. 36 11.16 Engine bleed air valve Rem./Inst. B1.1 B737-200 3
182. 36 11.16 Bleed air pre-cooler valve Removal/Installation B1.1 B737-200 2
183. 36 11.16 Engine bleed air check valve Rem./Inst. B1.1 B737-200 2
184. 38 11.17 Water fill and overflow valve - removal/installation B1.1 B737-200 2

Issue (1) Feb.2020 Revision: 01 Page 9 of 12

 Controlled Form MAA.MTO-QP13F-50

185. 38 11.17 Water tank drain valve - removal/installation B1.1 B737-200 3

186. 38 11.17 Water tank pressurization system filter - Rem./Inst. B1.1 B737-200 3
187. 38 11.17 Water tank pressure relief valve - removal/installation B1.1 B737-200 3
188. 38 11.17 Water tank rem./inst. B1.1 B737-200 12
189. 31 11.18 Audio selecting system - description and operation B1.1 B737-200 4
190. 34 11.19 Air data computer-removal/installation B1.1 B737-200 3
191. 23 11.20 Passenger address loudspeakers - removal/installation B1.1 B737-200 5
192. 34 11.21 Air traffic control (ATC) antenna - Rem./Inst. B1.1 B737-200 2
Total = 300
Module 15
193. 71 15.1 Identify and locate engine main components B1.1 Engine shop 2 2
194. 72 15.2 B737-200-200/JT8D-17 general specifications B1.1 B737-200-200/JT8D 2
195. 72 15.3 Nose cowl ant-icing duct- removal/installation B1.1 B737-200-200/JT8D 6
196. 72 15.4 Inspect Compressor 1st Stage by Borescope B1.1 Engine shop 2 2
197. 72 15.5 Combustion chamber numbering B1.1 Engine shop 2 1
198. ---- 15.5 Identify & distinguish types of combustion chamber B1.1 Engine shop 2 2
199. 75 15.6 Turbine blades / visual inspection B1.1 Engine shop 2 2
200. 72 15.7 Exhaust cone removal and installation B1.1 B737-200-JT8D 2
201. ---- 15.8 Distinguish between ball & roller bearings B1.1 Engine shop 2 2
202. 79 15.9 Removal and installation of fuel-cooled oil cooler. B1.1 B737-200/JT8D 3
203. 79 15.9 Removal and installation of oil filter. B1.1 B737-200/JT8D 3
204. ---- 15.9 Perform fuel contamination- water detection B1.1 B737-200/JT8D 3
205. 79 15.9 Removal and installation of oil pump B1.1 B737-200/JT8D 3
206. 79 15.10 Engine Oil Tank – Removal / installation B1.1 B737-200/JT8D 3
Description & operation of engine oil distribution system (Oil
207. 79 15.10 B1.1 B737-200/JT8D 2
system follow-up)
208. 79 15.11 Removal and installation of fuel nozzle. B1.1 B737-200/JT8D 3
209. 73 15.11 Fuel control main filter group – removal / installation B1.1 B737-200/JT8D 4
210. 75 15-12 Nose cowl anti-icing shutoff valve Removal / installation B1.1 B737-200/JT8D 6
211. ---- 15.12 Explain engine intake hot air anti-ice system function B1.1 Engine shop 2 2
212. 74 15.13 Describe The Layout and Components of Ignition System B1.1 B737-200/JT8D 2
213. 74 15.13 Replace igniter plug B1.1 B737-200/JT8D 4

Issue (1) Feb.2020 Revision: 01 Page 10 of 12

 Controlled Form MAA.MTO-QP13F-50

214. 80 15.13 Starter Motor - Removal/Installation B1.1 B737-200 5

215. 74 15.13 High tension leads - removal/installation B1.1 B737-200/JT8D 3
216. 74 15.13 High tension leads - adjustment/test B1.1 B737-200/JT8D 3
217. 77 15.14 Exhaust gas temperature indicator - Rem./Inst. B1.1 B737-200 3
218. 77 15.14 Exhaust gas temperature thermocouple probe - Rem./Inst. B1.1 B737-200/JT8D 5
219. 79 15.14 Oil temperature bulb - removal/installation B1.1 B737-200 3
220. 73 15.14 Fuel flow power supply - removal/installation B1.1 B737-200 4
221. ---- 15.15 Identify reheat system components B1.1 Engine shop 2 2
222. ---- 15.16 locate Turboprop engine main components B1.1 Engine shop 1 2
223. ---- 15.17 Identify main parts of turboshaft engine B1.1 Engine shop 2 2
224. 49 15.18 Perform APU’s oil tank oil change B1.1 Engine shop 2 2
225. ---- 15.19 Explain the purpose of engine cowling door B1.1 B737-200/JT8D 2
226. 77 15.20 Engine/APU Fire Control Module - Removal/Installation B1.1 B737-200 3
227. 26 15.20 Do the Operational Test of the Engine Fire Detection System B1.1 B737-200 4
228. ---- 15.21 Commonly Used Hand Signals for Ground Running B1.1 B737-200/JT8D 3
229. ---- 15.21 Engine preparation Before Starting the Engine B1.1 B737-200/JT8D 4
230. 72 15.22 Demonstrate engine preservation B1.1 Engine shop 2 2
Total =111
Module 17
231. 61 17.1 Propeller Identification and Description and classifications B1.1 Engine shop 2 2
Visually inspect propeller blades and front spinner for cracks,
232. 61 17.2
dents….
B1.1 Engine shop 2 3
233. 61 17.6 Propeller Blade Damage Repair B1.1 Engine shop 2 6
234. 61 17.6 Propeller removal/installation B1.1 Engine shop 2 6
235. 61 17.6 Propeller tracking B1.1 Engine shop 2 4
236. 61 17.7 Propeller Storage & Preservation Procedure B1.1 MAA Store 3
Total = 24

Total = 700 Hrs

Issue (1) Feb.2020 Revision: 01 Page 11 of 12