Scribd
Upload
17 views

Lab Assignment - 3

Uploaded by

somu ghorai
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
17 views

Lab Assignment - 3

Uploaded by

somu ghorai
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

E&HV Lab Assignment: 3

Course No: AEZG518/AELZG518


Course Title: Electric & Hybrid Vehicles Lab
Date assigned: 19-02-2024
Instruction to be followed while submitting the assignment:
1. Upload your submission through the Taxila system as per the deadline noted above. The system will
only accept submissions by the deadline.
2. Your submission MUST be a SINGLE FILE (in pdf format) – the system will accept only a single
file towards your submission. The system will allow you to submit ONLY once – no changes are
possible after you upload.
3. Submissions outside the Taxila system (such as e-mails, WhatsApp, etc.) will be neither
acknowledged nor considered for evaluation.
4. Before you upload, ensure that (i) you are submitting the correct document, (ii) the pages of your
document are correctly sequenced, (iii) the document is a clear scan (if scanned), and legible if
handwritten, (iv) the question numbers are marked, and (v) your name & BITS ID are indicated.
5. Please DO NOT submit your Simulink model files.
If you face system difficulties with your submission, please contact the student help desk for support.

1. Perform the E.V. model with different speeds, Battery Pack, and vehicle tire radius for both the
modes as in Load and No-load condition, and prepare an observation table with necessary
screenshots. Hint: Refer to Lab lecture 4 for the successful completion of the task
a) Plot a graph by using the below-mentioned table 1&2
Table: 1(a)_ VBattery pack_1 = 24V and Tire radius = 18

Motor Operating Mode


Sl.No n-ref (RPM) Pin(w) Vehicle speed Current SOC
PM_1 PM_2 Km/hr Drawn
1.

2.

3.

4.

5.

6.

7.

8.

9.

10.
Table: 1(b) _ VBattery pack_2 = 48V and Tire radius = 16

Motor Operating Mode


Sl.No n-ref (RPM) Pin(w) Vehicle speed Current SOC
PM_1 PM_2 Km/hr Drawn
1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

Table: 1 (a),(b) Observation table without enabling the PM_2 Load

Table: 2 (a) _ VBattery pack_1 = 24V and Tire radius = 18

Motor Operating Mode


Sl.No n-ref (RPM) Pin(w) Vehicle speed Current SOC
PM_1 PM_2 Km/hr Drawn
1.

2.

3.

4.

5.

6.

7.

8.

9.

10.
Table: 2 (b) _ VBattery pack_1 = 48V and Tire radius = 16

Motor Operating Mode


Sl.No n-ref (RPM) Pin(w) Vehicle speed Current SOC
PM_1 PM_2 Km/hr Drawn
1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

Table: 2 (a), (b) Observation table with enabling the PM_2 Load

Note: Try to find the bug while experimenting on the E.V. Model with different speed
combinations

2. Design a vehicle with Sizing scaling with different drive cycles and explain co-relating with
the theory using Dorleco Sim EV for the below
a) Sizing scaling of the power train only with battery
b) Sizing scaling of the power train only with motor
c) Sizing scaling of the power train complete vehicle. Take necessary screenshots if required
and submit them. Hint: Refer Lab lecture 4

$$$$$$$$$$$$$

You might also like