8th-Order, Lowpass, Bessel,

Switched-Capacitor Filters
ABSOLUTE MAXIMUM RATINGS
MAX7401/MAX7405

VDD to GND Continuous Power Dissipation (TA = +70°C)

MAX7401 ..............................................................-0.3V to +6V 8-Pin SO (derate 5.88mW/°C above +70°C)................471mW
MAX7405 ..............................................................-0.3V to +4V 8-Pin DIP (derate 9.09mW/°C above +70°C) ...............727mW
IN, OUT, COM, OS, CLK ...........................-0.3V to (VDD + 0.3V) Operating Temperature Ranges
SHDN........................................................................-0.3V to +6V MAX740 _C_A ....................................................0°C to +70°C
OUT Short-Circuit Duration...................................................1sec MAX740 _E_A .................................................-40°C to +85°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10sec) .............................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.

ELECTRICAL CHARACTERISTICS—MAX7401
(V DD = +5V, filter output measured at OUT, 10kΩ || 50pF load to GND at OUT, OS = COM, 0.1µF from COM to GND,
SHDN = VDD, fCLK = 100kHz, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
FILTER CHARACTERISTICS
Corner Frequency fC (Note 1) 0.001 to 5 kHz
Clock-to-Corner Ratio fCLK / fC 100:1
Clock-to-Corner Tempco 10 ppm/°C
Output Voltage Range 0.25 VDD - 0.25 V
Output Offset Voltage VOFFSET VIN = VCOM = VDD / 2 ±5 ±25 mV
DC Insertion Gain with
VCOM = VDD / 2 (Note 2) -0.1 0.15 0.3 dB
Output Offset Removed
Total Harmonic Distortion fIN = 200Hz, VIN = 4Vp-p,
THD+N -82 dB
plus Noise measurement bandwidth = 22kHz
OS Voltage Gain to OUT AOS 1 V/ V
Input Voltage Range at OS VOS VCOM ±0.1 V
VDD / 2 VDD / 2
Input, COM externally driven VDD / 2
- 0.5 + 0.5
COM Voltage Range VCOM V
VDD / 2 VDD / 2
Output, COM internally biased VDD / 2
- 0.2 + 0.2
Input Resistance at COM RCOM 75 125 kΩ
Clock Feedthrough 10 mVp-p
Resistive Output Load Drive RL 10 1 kΩ
Maximum Capacitive Load at
CL 50 500 pF
OUT
Input Leakage Current at COM SHDN = GND, VCOM = 0 to VDD ±0.1 ±10 µA
Input Leakage Current at OS VOS = 0 to (VDD - 1V) (Note 3) ±0.1 ±10 µA
CLOCK
Internal Oscillator Frequency fOSC COSC = 1000pF (Note 4) 29 38 48 kHz
Clock Input Current ICLK VCLK = 0 or 5V ±15 ±30 µA
Clock Input High VIH VDD - 0.5 V
Clock Input Low VIL 0.5 V

2 _______________________________________________________________________________________