SAFETY DATA SHEET

Delmax Lube HD 80W-90

Section 1. Identification
Product name : Delmax lube HD 80W-90
Product description : base oil and additives

Relevant identified uses of the substance or mixture and uses advised against
Identified uses : Gear oil
Uses advised against : This product is not recommended for any industrial, professional or consumer use
other than the Identified Uses above.

Supplier : MAL PAKISTAN LTD

D-46, BLOCK 5, KDA SCHEME # 5
CLIFTON KARACHI
KARACHI 75600 Pakistan
Contact : (92-21) 111-840-840

Section 2. Hazards identification

Classification of the : Not classified.
substance or mixture
This material is considered to be NON-HAZARDOUS according to regulatory
guidelines.

Other hazards which do not : None known.

result in classification
Nota : This material should not be used for any other purpose than the intended use in
Section 1 without expert advice. Health studies have shown that chemical exposure
may cause potential human health risks which may vary from person to person.

Section 3. Composition/information on ingredients

Substance/mixture : Mixture

Ingredient name % CAS number

distillates (petroleum), hydrotreated heavy paraffinic ≥50 - ≤75 64742-54-7

distillates (petroleum), solvent-dewaxed heavy paraffinic ≥50 - ≤75 64742-65-0

residual oils (petroleum), solvent-dewaxed ≥10 - ≤25 64742-62-7

residual oils (petroleum), hydrotreated ≥10 - ≤25 64742-57-0

alkyl polysulfides ≤2.3 68937-96-2

amines, c12-14-tert-alkyl ≤0.17 68955-53-3

There are no additional ingredients present which, within the current knowledge of the supplier and in the
concentrations applicable, are classified as hazardous to health or the environment and hence require
reporting in this section.
Occupational exposure limits, if available, are listed in Section 8.

1/9
Delmax lube HD 80W-90

Section 4. First-aid measures

Description of necessary first aid measures
Eye contact : Immediately flush eyes with plenty of water, occasionally lifting the upper and lower
eyelids. Check for and remove any contact lenses. Get medical attention if irritation
occurs.
Inhalation : Remove victim to fresh air and keep at rest in a position comfortable for breathing.
Skin contact : Flush contaminated skin with plenty of water. Remove contaminated clothing and
shoes. Get medical attention if symptoms occur. If product is injected into or under
the skin, or into any part of the body, regardless of the appearance of the wound or
its size, the individual should be evaluated immediately by a physician as a surgical
emergency. Even though initial symptoms from high pressure injection may be
minimal or absent, early surgical treatment within the first few hours may
significantly reduce the ultimate extent of injury.
Ingestion : Wash out mouth with water. If material has been swallowed and the exposed
person is conscious, give small quantities of water to drink. Do not induce vomiting
unless directed to do so by medical personnel.

Most important symptoms/effects, acute and delayed

Potential acute health effects
Eye contact : No known significant effects or critical hazards.
Inhalation : No known significant effects or critical hazards.
Skin contact : No known significant effects or critical hazards.
Ingestion : No known significant effects or critical hazards.
Over-exposure signs/symptoms
Eye contact : No specific data.
Inhalation : No specific data.
Skin contact : Local necrosis as evidenced by delayed onset of pain and tissue damage a few
hours after injection.
Ingestion : No specific data.

Indication of immediate medical attention and special treatment needed, if necessary

Notes to physician : Treat symptomatically. Contact poison treatment specialist immediately if large
quantities have been ingested or inhaled.
Specific treatments : No specific treatment.
Protection of first-aiders : No action shall be taken involving any personal risk or without suitable training.

See toxicological information (Section 11)

Section 5. Firefighting measures

Extinguishing media
Suitable extinguishing : Use dry chemical, CO₂, water spray (fog) or foam.
media
Unsuitable extinguishing : Do not use water jet.
media

Specific hazards arising : In a fire or if heated, a pressure increase will occur and the container may burst.
from the chemical This material is harmful to aquatic life with long lasting effects. Fire water
contaminated with this material must be contained and prevented from being
discharged to any waterway, sewer or drain.
Hazardous combustion : Aldehydes, Incomplete combustion products, Oxides of carbon, Smoke, Fume,
products sulfur oxides

2/9
Delmax lube HD 80W-90

Section 5. Firefighting measures

Special protective actions : Use standard firefighting procedures and consider the hazards of other involved
for fire-fighters materials. Promptly isolate the scene by removing all persons from the vicinity of
the incident if there is a fire. Assure an extended cooling down period to prevent re-
ignition. Prevent run-off from fire control or dilution from entering streams, sewers
or drinking water supply. No action shall be taken involving any personal risk or
without suitable training.
Special protective : Fire-fighters should wear appropriate protective equipment and self-contained
equipment for fire-fighters breathing apparatus (SCBA) with a full face-piece operated in positive pressure
mode.

Section 6. Accidental release measures

NOTIFICATION PROCEDURES
In the event of a spill or accidental release, notify relevant authorities in accordance with all applicable regulations.
Personal precautions, protective equipment and emergency procedures
For non-emergency : No action shall be taken involving any personal risk or without suitable training.
personnel Evacuate surrounding areas. Keep unnecessary and unprotected personnel from
entering. Do not touch or walk through spilt material. Put on appropriate personal
protective equipment.
For emergency responders : If specialised clothing is required to deal with the spillage, take note of any
information in Section 8 on suitable and unsuitable materials. See also the
information in "For non-emergency personnel".

Environmental precautions : Avoid dispersal of spilt material and runoff and contact with soil, waterways, drains
and sewers. Inform the relevant authorities if the product has caused environmental
pollution (sewers, waterways, soil or air). Water polluting material. May be harmful
to the environment if released in large quantities.

Methods and material for containment and cleaning up

Small spill : Stop leak if without risk. Move containers from spill area. Dilute with water and mop
up if water-soluble. Alternatively, or if water-insoluble, absorb with an inert dry
material and place in an appropriate waste disposal container. Dispose of via a
licensed waste disposal contractor.
Large spill : Stop leak if without risk. Move containers from spill area. Approach the release
from upwind. Prevent entry into sewers, water courses, basements or confined
areas. Wash spillages into an effluent treatment plant or proceed as follows.
Contain and collect spillage with non-combustible, absorbent material e.g. sand,
earth, vermiculite or diatomaceous earth and place in container for disposal
according to local regulations (see Section 13). Dispose of via a licensed waste
disposal contractor. Contaminated absorbent material may pose the same hazard
as the spilt product. Confine the spill immediately with booms. Remove from the
surface by skimming or with suitable absorbents. Seek the advice of a specialist
before using dispersants. Warn other shipping. Note: see Section 1 for emergency
contact information and Section 13 for waste disposal.
Water spill and land spill recommendations are based on the most likely spill scenario for this material; however,
geographic conditions, wind, temperature, (and in the case of a water spill) wave and current direction and speed may
greatly influence the appropriate action to be taken. For this reason, local experts should be consulted. Note: Local
regulations may prescribe or limit action to be taken.

Section 7. Handling and storage

Precautions for safe handling
Protective measures : Put on appropriate personal protective equipment (see Section 8). Do not ingest.
Avoid contact with eyes, skin and clothing. Avoid breathing vapour or mist. Avoid
release to the environment. Keep in the original container or an approved
alternative made from a compatible material, kept tightly closed when not in use.
Empty containers retain product residue and can be hazardous. Do not reuse
container.

3/9
Delmax lube HD 80W-90

Section 7. Handling and storage

Advice on general : Eating, drinking and smoking should be prohibited in areas where this material is
occupational hygiene handled, stored and processed. Workers should wash hands and face before
eating, drinking and smoking. Remove contaminated clothing and protective
equipment before entering eating areas. See also Section 8 for additional
information on hygiene measures.
Static Accumulator : This material is a static accumulator. A liquid is typically considered a
nonconductive, static accumulator if its conductivity is below 100 pS/m (100x10E-12
Siemens per meter) and is considered a semiconductive, static accumulator if its
conductivity is below 10,000 pS/m. Whether a liquid is nonconductive or
semiconductive, the precautions are the same. A number of factors, for example
liquid temperature, presence of contaminants, anti-static additives and filtration can
greatly influence the conductivity of a liquid.

Conditions for safe storage, : Store in accordance with local regulations. Store in original container protected
including any from direct sunlight in a dry, cool and well-ventilated area, away from incompatible
incompatibilities materials (see Section 10) and food and drink. Keep container tightly closed and
sealed until ready for use. Containers that have been opened must be carefully
resealed and kept upright to prevent leakage. Do not store in unlabelled containers.
Use appropriate containment to avoid environmental contamination. See Section 10
for incompatible materials before handling or use.

Section 8. Exposure controls/personal protection

Control parameters
Occupational exposure limits
Ingredient name Exposure limits
distillates (petroleum), hydrotreated heavy Workplace Safety and Health Act (Pakistan, 2/2006). [Oil Mist,
paraffinic mineral]
PEL (long term): 5 mg/m³ 8 hours. Form: Mist
PEL (short term): 10 mg/m³ 15 minutes. Form: Mist
ACGIH TLV (United States, 1/2022). [Mineral Oil, pure, highly
and severely refined]
TWA: 5 mg/m³ 8 hours. Form: Inhalable fraction
ACGIH TLV (United States, 1/2023). [Mineral Oil, pure, highly
and severely refined]
TWA: 5 mg/m³ 8 hours. Form: Inhalable fraction
distillates (petroleum), solvent-dewaxed heavy Workplace Safety and Health Act (Pakistan, 2/2006). [Oil Mist,
paraffinic mineral]
PEL (long term): 5 mg/m³ 8 hours. Form: Mist
PEL (short term): 10 mg/m³ 15 minutes. Form: Mist
ACGIH TLV (United States, 1/2022). [Mineral Oil, pure, highly
and severely refined]
TWA: 5 mg/m³ 8 hours. Form: Inhalable fraction
ACGIH TLV (United States, 1/2023). [Mineral Oil, pure, highly
and severely refined]
TWA: 5 mg/m³ 8 hours. Form: Inhalable fraction
residual oils (petroleum), solvent-dewaxed Workplace Safety and Health Act (Pakistan, 2/2006). [Oil Mist,
mineral]
PEL (long term): 5 mg/m³ 8 hours. Form: Mist
PEL (short term): 10 mg/m³ 15 minutes. Form: Mist
ACGIH TLV (United States, 1/2023). [Mineral Oil, pure, highly
and severely refined]
TWA: 5 mg/m³ 8 hours. Form: Inhalable fraction
residual oils (petroleum), hydrotreated Workplace Safety and Health Act (Pakistan, 2/2006). [Oil Mist,
mineral]
PEL (long term): 5 mg/m³ 8 hours. Form: Mist
PEL (short term): 10 mg/m³ 15 minutes. Form: Mist
ACGIH TLV (United States, 1/2023). [Mineral Oil, pure, highly

4/9
Delmax lube HD 80W-90

Section 8. Exposure controls/personal protection

and severely refined]
TWA: 5 mg/m³ 8 hours. Form: Inhalable fraction
NOTE: Limits/standards shown for guidance only. Follow applicable regulations.

Appropriate engineering : Good general ventilation should be sufficient to control worker exposure to airborne
controls contaminants.
Environmental exposure : Emissions from ventilation or work process equipment should be checked to ensure
controls they comply with the requirements of environmental protection legislation. In some
cases, fume scrubbers, filters or engineering modifications to the process
equipment will be necessary to reduce emissions to acceptable levels.

Individual protection measures

Hygiene measures : Wash hands, forearms and face thoroughly after handling chemical products, before
eating, smoking and using the lavatory and at the end of the working period.
Appropriate techniques should be used to remove potentially contaminated clothing.
Wash contaminated clothing before reusing. Ensure that eyewash stations and
safety showers are close to the workstation location.
Eye/face protection : Safety eyewear complying with an approved standard should be used when a risk
assessment indicates this is necessary to avoid exposure to liquid splashes, mists,
gases or dusts. If contact is possible, the following protection should be worn,
unless the assessment indicates a higher degree of protection: safety glasses with
side-shields.
Skin protection
Hand protection : Chemical-resistant, impervious gloves complying with an approved standard should
be worn at all times when handling chemical products if a risk assessment indicates
this is necessary. Considering the parameters specified by the glove manufacturer,
check during use that the gloves are still retaining their protective properties. It
should be noted that the time to breakthrough for any glove material may be
different for different glove manufacturers. In the case of mixtures, consisting of
several substances, the protection time of the gloves cannot be accurately
estimated.
Body protection : Personal protective equipment for the body should be selected based on the task
being performed and the risks involved and should be approved by a specialist
before handling this product.
Other skin protection : Appropriate footwear and any additional skin protection measures should be
selected based on the task being performed and the risks involved and should be
approved by a specialist before handling this product.
Respiratory protection : Based on the hazard and potential for exposure, select a respirator that meets the
appropriate standard or certification. Respirators must be used according to a
respiratory protection program to ensure proper fitting, training, and other important
aspects of use.

Section 9. Physical and chemical properties and safety

characteristics
Note: Physical and chemical properties are provided for safety, health and environmental considerations only
and may not fully represent product specifications. Contact the Supplier for additional information.
The conditions of measurement of all properties are at standard temperature and pressure unless otherwise indicated.

Appearance
Physical state : Liquid.
Colour : Yellow to Brown
Odour : Characteristic
Odour threshold : Not available.
pH : Not applicable.
Melting point/freezing point : Not available.

5/9
Delmax lube HD 80W-90

Section 9. Physical and chemical properties and safety

characteristics
Boiling point, initial boiling : >315.56°C (>600°F)
point, and boiling range
Flash point : Open cup: 213°C (415.4°F) [ASTM D-92]
Evaporation rate : Not available.
Flammability : Ignitable
Lower and upper explosion : Lower: 0.9%
limit/flammability limit Upper: 7%
Vapour pressure : <0.1 mm Hg [20 °C]
Relative vapour density : >2 [Air = 1]
Relative density : 0.8897
Solubility in water : Negligible
Partition coefficient: n- : >3.5
octanol/water
Auto-ignition temperature : Not available.
Decomposition temperature : Not available.
Viscosity : 131.6 cSt [40 °C] [ASTM D 445]
14.12 cSt [100 °C] [ASTM D 445]
Particle characteristics
Median particle size : Not applicable.
Pour point : -24°C [ASTM D97]
DMSO Extract (mineral oil : <3 % by weight
only), IP-346

Section 10. Stability and reactivity

Reactivity : No specific test data related to reactivity available for this product or its ingredients.

Chemical stability : The product is stable.

Possibility of hazardous : Under normal conditions of storage and use, hazardous reactions will not occur.
reactions

Conditions to avoid : High energy sources of ignition. Excessive heat.

Incompatible materials : Strong oxidisers

Hazardous decomposition : Under normal conditions of storage and use, hazardous decomposition products
products should not be produced.

Section 11. Toxicological information

Information on toxicological effects
Acute toxicity
Product/ingredient name Test Species Result Duration
amines, c12-14-tert-alkyl LC50 Inhalation Vapour Rat 1.19 mg/l 4 hours
LD50 Dermal Rat 251 mg/kg -
LD50 Oral Rat 612 mg/kg -
Conclusion/Summary
Inhalation : Minimally Toxic. No end point data for material. Based on assessment of the
components.

6/9
Delmax lube HD 80W-90

Section 11. Toxicological information

Dermal : Minimally Toxic. No end point data for material. Based on assessment of the
components.
Oral : Minimally Toxic. No end point data for material. Based on assessment of the
components.
Irritation/Corrosion
Conclusion/Summary
Skin : Negligible irritation to skin at ambient temperatures. No end point data for material.
Based on assessment of the components.
Eyes : May cause mild, short-lasting discomfort to eyes. No end point data for material.
Based on assessment of the components.
Respiratory : Negligible hazard at ambient/normal handling temperatures. No end point data for
material.
Sensitisation
Conclusion/Summary
Skin : Not expected to be a skin sensitizer. No end point data for material. Based on
assessment of the components.
Respiratory : Not expected to be a respiratory sensitizer. No end point data for material.
Mutagenicity
Conclusion/Summary : Not expected to be a germ cell mutagen. No end point data for material. Based on
assessment of the components.
Carcinogenicity
Conclusion/Summary : Not expected to cause cancer. No end point data for material. Based on assessment
of the components.
Reproductive toxicity
Conclusion/Summary : Not expected to be a reproductive toxicant. No end point data for material. Based on
assessment of the components.
Specific target organ toxicity (single exposure)
Conclusion/Summary : Not expected to cause organ damage from a single exposure. No end point data for
material.
Specific target organ toxicity (repeated exposure)
Conclusion/Summary : Not expected to cause organ damage from prolonged or repeated exposure. No end
point data for material. Based on assessment of the components.
Aspiration hazard
Conclusion/Summary : Not expected to be an aspiration hazard. Based on physico-chemical properties of
the material. Data available.

Other information
Contains : Base oil severely refined: Not carcinogenic in animal studies. Representative material
passes IP-346, Modified Ames test, and/or other screening tests. Dermal and
inhalation studies showed minimal effects; lung non-specific infiltration of immune
cells, oil deposition and minimal granuloma formation. Not sensitising in test animals.
Product : Component concentrations in this formulation would not be expected to cause skin
sensitization, based on tests of the components, this formulation, or similar
formulations.

Section 12. Ecological information

The information given is based on data for the material, components of the material, or for similar materials, through
the application of bridging principals.
Toxicity
Conclusion/Summary
Acute toxicity : Harmful to aquatic life.
Chronic toxicity : Harmful to aquatic life with long lasting effects.

7/9
Delmax lube HD 80W-90

Section 12. Ecological information

Persistence and degradability

Biodegradability : Base oil component -- Expected to be inherently biodegradable

Bioaccumulative potential
Conclusion/Summary : Base oil component -- Has the potential to bioaccumulate, however metabolism or
physical properties may reduce the bioconcentration or limit bioavailability.

Mobility in soil
Mobility : Base oil component -- Expected to partition to sediment and wastewater solids. Low
solubility and floats and is expected to migrate from water to the land.

Other ecological information

Other adverse effects : No known significant effects or critical hazards.

Section 13. Disposal considerations

Disposal methods : The generation of waste should be avoided or minimised wherever possible.
Disposal of this product, solutions and any by-products should at all times comply
with the requirements of environmental protection and waste disposal legislation and
any regional local authority requirements. Dispose of surplus and non-recyclable
products via a licensed waste disposal contractor. Waste should not be disposed of
untreated to the sewer unless fully compliant with the requirements of all authorities
with jurisdiction. Waste packaging should be recycled. Incineration or landfill
should only be considered when recycling is not feasible. Avoid dispersal of spilt
material and runoff and contact with soil, waterways, drains and sewers.

Empty Container Warning (where applicable): Empty containers may contain

residue and can be dangerous. Do not attempt to refill or clean containers without
proper instructions. Empty drums should be completely drained and safely stored
until appropriately reconditioned or disposed. Empty containers should be taken for
recycling, recovery, or disposal through suitably qualified or licensed contractor and
in accordance with governmental regulations. DO NOT PRESSURISE, CUT,
WELD, BRAZE, SOLDER, DRILL, GRIND, OR EXPOSE SUCH CONTAINERS TO
HEAT, FLAME, SPARKS, STATIC ELECTRICITY, OR OTHER SOURCES OF
IGNITION. THEY MAY EXPLODE AND CAUSE INJURY OR DEATH.

Section 14. Transport information

ADR IMDG IATA
UN number Not regulated. Not regulated. Not regulated.

UN proper - - -
shipping name
Transport hazard - - -
class(es)
Packing group - - -
Environmental No. No. No.
hazards

Special precautions for user : Transport within user’s premises: always transport in closed containers that are
upright and secure. Ensure that persons transporting the product know what to do in
the event of an accident or spillage.

8/9
Delmax lube HD 80W-90

Section 14. Transport information

Transport in bulk according : Not applicable.
to IMO instruments

Section 15. Regulatory information

This material is considered to be NON-HAZARDOUS according to regulatory guidelines.
Inventory list
Australia inventory (AIIC) : All components are listed or exempted.
Canada inventory (DSL-NDSL) : All components are listed or exempted.
China inventory (IECSC) : All components are listed or exempted.
Japan inventory (CSCL) : All components are listed or exempted.
Japan inventory (Industrial Safety and : All components are listed or exempted.
Health Act)
New Zealand Inventory of Chemicals : All components are listed or exempted.
(NZIoC)
Philippines inventory (PICCS) : All components are listed or exempted.
Korea inventory (KECI) : All components are listed or exempted.
Taiwan Chemical Substances Inventory : All components are listed or exempted.
(TCSI)
United States inventory (TSCA 8b) : All components are active or exempted.

Section 16. Other information

History
Date of issue/Date of : 25 January 2024
revision
Date of previous issue : No previous edition
Version : 1
Key to abbreviations : ATE = Acute Toxicity Estimate
BCF = Bioconcentration Factor
GHS = Globally Harmonized System of Classification and Labelling of Chemicals
IATA = International Air Transport Association
IBC = Intermediate Bulk Container
IMDG = International Maritime Dangerous Goods
LogPow = logarithm of the octanol/water partition coefficient
MARPOL = International Convention for the Prevention of Pollution From Ships,
1973 as modified by the Protocol of 1978. ("Marpol" = marine pollution)
N/A = Not available
SGG = Segregation Group
UN = United Nations
References : Not available.

Notice to reader
"The information and recommendations contained herein are, to the best of MAL Pakistan Limited
knowledge and belief, accurate and reliable as of the date issued. You can contact MAL Pakistan Limited to
insure that this document is the most current available from MAL Pakistan Limited. The information and
recommendations are offered for the user's consideration and examination. It is the user's responsibility to
satisfy itself that the product is suitable for the intended use. If buyer repackages this product, it is the
user's responsibility to insure proper health, safety and other necessary information is included with and/or
on the container. Appropriate warnings and safe-handling procedures should be provided to handlers and
users. Alteration of this document is strictly prohibited.

9/9