M/S.

JAYANSREE PHARMA PRIVATE LIMITED

AT VIZAG, A.P

TENDER
FOR
CONSTRUCTION OF SODIUM SULPHIDE PROJECT

MAIN ABSTRACT
Rev-00 - Dated:03.01.19
TITLE AMOUNT (RS.)

PLANT AND NON PLANT

PART-I : CIVIL WORKS
STRUCTURES

PART-II : STRUCTURAL PLANT AND NON-PLANT

STEEL WORKS STRUCTURES

GRAND TOTAL:

RS. IN WORDS:

DATE :
PLACE :
 M/S. JAYANSREE PHARMA PRIVATE LIMITED

AT VIZAG, A.P

TENDER
FOR
CONSTRUCTION OF SODIUM SULPHIDE PROJECT

PART-I : CIVIL WORKS

PLANT AND NON-PLANT STRUCTURES

ABSTRACT

S No SECTION TITLE

1 SECTION 'A' EARTHWORK/SOLING

2 SECTION 'B' CONCRETE PLAIN & REINFORCED

3 SECTION 'C' MASONRY & PLASTER

4 SECTION 'D' FLOORING

5 SECTION 'E ' PAINTING

6 SECTION ' F' DOORS, WINDOWS & VENTILATORS

7 SECTION 'G' WATERPROOFING

8 SECTION 'H' MISCELLANEOUS

9 SECTION 'I' ROAD & DRAINAGES

GRAND TOTAL

RS. IN WORDS:
ATE LIMITED

E PROJECT

KS
TURES

Rev-00 - Dated:03.01.19

AMOUNT (RS.)
 M/S. JAYANSREE PHARMA PRIVATE LIMITED

AT VIZAG, A.P

TENDER
FOR
CONSTRUCTION OF SODIUM SULPHIDE PROJECT

PART-II : STRUCTURAL STEEL WORKS

PLANT AND NON-PLANT STRUCTURES

ABSTRACT

S No SECTION TITLE

1 SECTION 'A' STRUCTURAL STEEL WORK

2 SECTION 'B' ROOFING & ACCESSORIES

GRAND TOTAL

RS. IN WORDS:
ATE LIMITED

E PROJECT

L WORKS

TURES

Rev-00 - Dated: 03.01.19

AMOUNT(RS.)
 PART-I

M/S. JAYANSREE PHARMA PRIVATE LIMITED

AT VIZAG, A.P

TENDER
FOR
CONSTRUCTION OF SODIUM SULPHIDE PROJECT

PART-I : CIVIL WORKS

PLANT AND NON-PLANT STRUCTURES

BILL OF QUANTITIES
Rev-00 - Dated: 03.01.19
Notes: 1.' Rates of all items must be filled in.

2. 'Quantities are probable and may vary.

3. 'Rates shall include whether stated in the item or not, cutting, chases, holes, etc. in walls and floors wherever
necessary and reinstating them to original conditions.

4.The contractor may use batching plant or weigh batchers.

5.The rates shall include slush removing, side dressing, cleaning the foundation pits for concreting and dewatering
arrangement and other miscellaneous works till pouring of concrete.

6. Q.R.O. means Quote Rate Only.

NOTE:
Cement & Rebars Supplied by JPPL at agreed price.

S.No. Description QTY UNIT Rate AMOUNT

(RS.) (RS.)
Section 'A"-Earthwork :

A01 Excavation in all types of soils viz.black cotton soil, clay, sand,
murrum etc but other than soft and hard rock for foundations of
walls, columns, trenches, equipments etc. as per drawings including
strutting, shoring of sides and dewatering where ever required and
stacking/spreading of excavated materials within 200M.

a) From average ground level to 1.0 m depth 2000 Cu.m.

b) From 1.0M to 2.0M depth 2000 Cu.m.
c) From 2.0M to 3.0M depth 2000 Cu.m.

A02 Same as in Item No A01 but in Soft Rock and loose boulders
a) Upto 1.0M depth from ground level 200 Cu.m.
b) From 1.0M to 2.0M depth 200 Cu.m.
c) From 2.0M to 3.0M depth 200 Cu.m.

A03 Same as in Item No A01 but in Hard Rock by controlled blasting,

chiselling.
a) Upto 1.0M depth from ground level 100 Cu.m.
b) From 1.0M to 2.0M depth 100 Cu.m.

Page 1
 PART-I

S.No. Description QTY UNIT Rate AMOUNT

(RS.) (RS.)
c) From 2.0M to 3.0M depth 100 Cu.m.

A04 a) Filling and Backfilling in plinth, around footings, pits, foundation

etc. with excavated earth lying in and around work site, laid in layers
not exceeding 200mm thickness watering, compacting by
ramming/rolling, levelling etc. complete as directed.

3500 Cu.m.
b) Same as item No 4a but with murrum brought from outside the
Owner's property
100 Cu.m.
c) Same as in item No 4a but filling with medium sand brought
from outside the Owner's property,
100 Cu.m.

A05 Disposing of surplus excavated materials by carting away, spreading

evenly and levelling at selected places or as directed within a lead of
1.0 KM 3500 Cu.m.

A06 Extra over Item No A05 above for every additional lead of 1.0 KM
QRO Cu.m.

A07 Providing and laying rubble soling including hand packing, filling
with interstices with chips and sand, watering and compacting etc.
complete.

a) 230 mm thick soling 800 Sq.m

b) 150 mm thick soling 100 Sq.m

A08 Same as above A07, but with Owner's rubble

a) 230 mm thick soling QRO Sq.m
b) 150 mm thick soling QRO Sq.m

A09 Plinth protection alround the building as per Engineering drawing 300 Sq.m
Total of Section 'A' :

Section 'B' Plain and Reinforced Concrete:

B01 Providing and laying Plain Cement Concrete in foundations with 40

mm coarse aggregate of approved quality including levelling,
compacting, curing etc. complete

a) Mix 1:4:8 (M-7.5 grade) 250 Cu.m.

b) Mix 1:3:6 (M-10 grade) 90 Cu.m.
c) mix 1:2:4 (M-15 grade) QRO Cu.m.

Page 2
 PART-I

S.No. Description QTY UNIT Rate AMOUNT

(RS.) (RS.)
B02 Providing and laying Reinforced cement concrete with 20 mm and
downgraded stone metal aggregate in all types of work in
foundations/plinth/superstructure like pedestals, columns, slabs,
beams, walls, hoppers, chajjas, canopies etc. slipped formed shell
wall etc. including vibrating, consolidating, finishing curing etc.,
complete but excluding formwork and reinforcement.

a) in foundation and upto plinth

i) M20 Grade 100 Cu.m.
ii) M25 Grade 2300 Cu.m.
iii) M30 Grade QRO Cu.m.
b) in superstructure
i) M20 Grade QRO Cum
ii) M25 Grade 600 Cum
iii) M-30 Grade QRO Cum

B03 Extra over item B02above for Lifts for concreting from
a) 0.0 M to 3.60 M 200 Cu.m.
b) 3.60 M to 7.20 M 200 Cu.m.
c) 7.20 M to 10.80 M 200 Cu.m.

B04 Providing and fixing in position Rough Formwork/Shuttering

including necessary alignment and levels to all RCC work and
removing the same after specified period etc complete.

i) For plain surface upto +/-0.0M 3500 Sq.m.

B05 Providing and fixing in position form Finished Form

work( Exposed) including necessary alignment and levels to all
RCC work and including all necessary scaffolding,
propping/staging required for the form work at any heights and
removing the same after specified period etc. complete.

i) For plain surface

a) Upto 0.00m lvl. 900 Sq.m
b) 0.0 M to 3.60M 1400 Sq.m
c) 3.60 M to 7.20M 1400 Sq.m
d) 7.20 M to 10.80M 1400 Sq.m

ii) For curved surface

a) upto ± 0.00 M Level 600 Sq.m
b) 0.0 M to 3.60 M QRO Sq.m
c) 3.60 M to 7.20 M QRO Sq.m
d) 7.20 M to 10.80 M QRO Sq.m

Providing and fixing in position form finished form work/shuttering

for cones/inclined hoppers concreting work, including all necessary
scaffolding, propping/stagging required for the form work at any
B06 heights and removing the same after specified period, all as per
drawing and as directed.

QRO Sq.m

Page 3
 PART-I

S.No. Description QTY UNIT Rate AMOUNT

(RS.) (RS.)

Collecting from Storage Yard, transportation, fabricating, laying and

fixing in position Reinforcement for all RCC work at all heights
including straightening, cutting, bending and binding with 16 gauge
B07 annealed black wire, spacer blocks of CM 1:2 embedded with
binding wire etc.(chairs, pins, authorised laps will be measured and
paid for)

i)Upto +/- 0.00 M 270 MT

ii) 0.0M to 3.60 M 30 MT
iii)3.60 M to 7.20 M 30 MT
iv) 7.20 M to 10.80 M 30 MT

B08 Providing and fixing pockets of various sizes and depths in position
in PCC/RCC work at all levels and carefully removing the same for
anchor, HD bolts, equipment foundations etc all as per drawing and
as directed by the Engineer.

10 Sq.m

B09 Providing and grouting under base plates of equipment foundation,

pockets for HD bolts with cement mortar 1:1 inclusive of approved
non-shrinkage additive compound, formwork if any, finishing,
curing etc complete.
1 Cum

B10 Same as above but grouting with non-shrink grout. 1 Cum

B11 a) Providing and placing plum concrete (50:50) consisting of 50%

1:4:8 PCC and 50% rubble pieces of size between 150mm and
200mm complete as per drawing, specifications and as directed by
the Engineer.
90 Cu.m.
b) Same as Item No.B14a but in ratio of 70:30 i.e. 70% of PCC
1:5:10 and 30% of plum. 10 Cu.m.

B12 Same as in Item No B14 above but with Owner's Rubble

a) 70:30 ratio with 70% 1:5:10 PCC and 30 % plum QRO Cum
b) 50:50 ratio with 50% 1:4:8 PCC and 50% plum QRO Cum

B13 Providing and laying 40 mm thick screed concrete in Mix M15 with
20 mm downgraded stone metal aggregate laid to required slope
over concrete surface including hacking of concrete, formwork if
any, curing etc complete.
800 Sq.m

B14 Extra over Item No B.02 for providing and mixing admixture like
plasticiser and retarding agent in cement concrete as directed by the
Engineer. (Measurement for concrete work for which admixture is
added).
QRO Cum

Page 4
 PART-I

S.No. Description QTY UNIT Rate AMOUNT

(RS.) (RS.)
Total of Section 'B':

Section 'C' Masonry and Plaster:

C01 Providing and constructing random rubble masonry in CM 1:5

including sunk pointing on the outer face, scaffolding, raking out
joints, curing etc complete.

a) In foundation and plinth 120 Cum

b) In superstructure 60 Cum

C02 Providing and constructing brick masonry in 230/115 MM and

above thick in foundation and superstructure including scaffolding,
raking out joints, curing etc complete as per drawing and as directed
by the Engineer at all heights.
500 Cum

C03 Providing and applying smooth plaster in CM1:4 for walls, beams,
columns and around openings in jambs, soffits and cills including
scaffolding, hacking of concrete surfaces, curing etc complete at all
heights.

a) 8 mm to ceiling 700 Sq.m

b) 12 mm thick to wall etc. 4300 Sq.m

C04 Providing and applying 20 mm thick sand faced cement plaster in

two coats in CM1:4 to external concrete surface and masonry work
etc including scaffolding, hacking of concrete surfaces, curing etc
complete at all heights.

50 Sq.m

C05 Providing and laying cement plaster in CM 1:4 at all heights to

internal/external surfaces of walls, RCC work etc. rubbed
smooth/Smooth Cement finish including hacking of concrete
surfaces raking of joints, scaffolding, curing etc. complete.

a) 20 mm thick 25 Sq.m

C06 Providing and fixing in position 24 gauge chicken wire mesh at

junctions of concrete and brick wall or on cement and brick surfaces
for plaster at all heights including scaffolding etc complete.

75 Sq.m

Total of Section 'C':

SECTION 'D' - Flooring:

D01 a) 'Providing and laying 50 mm thick I.P.S. flooring in cement

concrete 1:2:4 using 12 mm down graded stone metal laid to level or
slope in alternate bays with 3 mm x 50 mm glass strips in between
panels and finished smooth as directed including compaction,
curing, etc. complete.
QRO Sq.m

Page 5
 PART-I

S.No. Description QTY UNIT Rate AMOUNT

(RS.) (RS.)

b) Same as in Item No D01 a but without glass strips 850 Sq.m

D02 All as per item 1 but with chequered finish. QRO Sq.m

D03 All as per item 1 above but for treads of staircase with IPS finish
CM 15mm thk. For risers (Note:-Both tread & riser to be measured
together as Sq.m)
QRO Sq.m

D04 Providing and laying in position approved make first quality 6mm
thick Vertified tiles in required pattern at all levels on cement mortar
bedding with waterproofing additive, to true plane and level or to
slope, close jointed and pointed with white cement slurry including
cutting the tiles, providing holes for pipe line & fixtures, curing,
cleaning, etc. complete.

a) In floors over and including a bed of 20mm thick C.M. 1:3

i) 600mm x 600mm size 800 Sq.m
b) For dado over and including base coat of plaster 12mm thick and
neat cement paste (Item rate includes centre punching as per
requirement)

152mm x 152mm size 50 Sq.m

D05 Providing & laying 8mm thk Ceramic decorative tiles of approved
manufacturer in 1:3 C.M. closed jointed and pointed with matching
cement slurry finished to line & levels as required including
cleaning, curing etc. complete.

a) For flooring
(i) 600 mm x 600 mm size tiles 100 Sq.m
ii) 400mm x 400 mm size QRO Sq.m
b) For skirting & Dado over & including CM backing of 12mm
thick with 200 mm x 200 mm size tiles 20 Sq.m

D06 Providing and laying polished kotah stones flooring at all levels of
uniform tint and 450mm x 450mm size, hand dressed, laid on av.
25mm thick lime mortar 1 : 1 : 1 ( 1 lime : 1 surkhi : 1 coarse sand )
or cement mortar 1 : 4 (1 cement : 4 coarse sand ) bedding to a true
plane and level, or to slopes, closed jointed and pointed with
matching cement paste, including curing, machine polishing,
finishing, cleaning, etc. complete as per drawings and specifications.

a) For flooring with 25mm to 38mm thickness QRO Sq.m

b) For skirting with 20mm to 30mm thickness QRO Sq.m

Page 6
 PART-I

S.No. Description QTY UNIT Rate AMOUNT

(RS.) (RS.)
D07 a) Providing and laying 25 mm to 30 mm thick Marble flooring of
required size, machine cut, machine polished in including 25 mm
thick bedding cement mortar 1:4 and filling joints with neat white
cement slurry with matching colour, curing, polishing and cleaning
etc. complete

800 Sq.m
b) Same as in Item No D.07 a) but for skirting/dado over 12 mm
thick backing coat 20 Sq.m

D08 Providing and fixing 40 mm thick Cudappa stone slab in CM 1:4 for
Platform including laying inline, levels, curing polishing etc
complete
QRO Sq.m
D09 Providing and laying black/grey coloured Granite stone slabs 25 mm
thick in and including 25 mm thick cement mortar 1:4 bedding on
floor/ Platform including laying in line, levels, curing polishing,
cleaning etc complete
5 Sq.m

Total of Section 'D':

Section 'E' Painting:

E01 Providing and applying three coats of white or colour wash

including cleaning the surfaces scaffolding etc. complete.
3000 Sq.m

E02 Providing and applying two coats of oil bound distemper of

approved make and shade over one coat of cement primer including
cleaning the surfaces scaffolding etc. complete.
500 Sq.m

E03 Providing and applying two coats of “SNOWCEM PLUS” cement

based paint of approved shade over a coat of CEMPROVER primer
and / or a diluted coat of Snowcem plus including cleaning the
surfaces, scaffolding, curing, etc. complete.

1000 Sq.m

E04 Providing and applying two coats of Super Acrylic Emulsion paint
of 'APCOLITE' of approved equivalent make and shade over one
coat of cement primer including cleaning the surfaces at all levels,
preparing the base to receive the primer, cleaning the surfaces,
scaffolding etc. complete.

500 Sq.m

Total of Section 'E':

Section-'F' Doors, Windows & Ventilators:

Page 7
 PART-I

S.No. Description QTY UNIT Rate AMOUNT

(RS.) (RS.)
F01 Providing and fixing in position approved quality MS rolling shutter
fabricated from 18 gauge MS sheets, including all necessary fittings
and fixtures, standard ball bearings, drum top cover from 18 gauge
MS sheet, Side guide channels fabricated from 10 Gauge MS sheet,
suspension shaft with tested springs, MS bracket plate with clamp,
MS stoppers, lock plate and locking arrangements, handles, etc.,
painted with one coat of red oxide primer and two coats of synthetic
enamel paint of approved manufacture, quality and shade, etc.
complete as per drawing, specifications and as directed by the
Engineer. (Measurements for clear wall openings) for the following :

a) Pull and Push type Rolling shutters. 20 Sq,.m

b) Hand gear operated Rolling shutters. 20 Sq,.m
c) Extra for providing Grills in Rolling Shutters QRO Sq,.m

F02 Providing and fixing in position MS door made out of standard press
metal steel frames 120mmx60mmx1.25mm thick of TRIGON or
equivalent make and 18 gauge MS sheet on both sides with 16
gauge pressed metal channel stiffeners including all MS fittings and
fixtures, painted with two coats of synthetic enamel paint of
approved make and shade, tint over one coat of red oxide primer etc.
complete as per drawings and specification.

(Measurement for clear unfinished size of opening).

a) MS Single shutter door 20 Sq.m
b) MS Double shutter door 10 Sq.m
F03 Providing, making and fixing in position teak wood panelled door
with 120mm x 60mm teak wood frame, shutter 100mm x 38mm teak
wood top rail and styles, 150mm x 38mm teak wood lock rail and
bottom rail and 12mm thick T.W. panels of approved quality
properly inserted in to the styles and rails, including necessary MS
hold fasts grouted in wall, brass oxidised hinges, fittings & fixtures
of approved quality, necessary fasteners, painting door with one coat
of wood primer and two coats of flat oil paint of approved make and
shade, all complete as per drawings and specifications (Rear side of
T.W. frame to be painted with bitumen paint).

a) Single shutter door 20 Sq.m

F04 Providing and fixing in position silver grey matt finish anodised
Aluminium Fixed Glazing of approved make using 6mm thick wired
glass panel with all fixtures fastening, weathering strips, PVC or
Neoprene rubber glazing clip, necessary fixtures and fastenings, etc.
complete as per drawing, specification and as directed by the
Engineer.

QRO Sq.m

Page 8
 PART-I

S.No. Description QTY UNIT Rate AMOUNT

(RS.) (RS.)
F05 Providing and fixing in position Silver grey matt finish anodised (15
microns) aluminium glazed sliding windows of approved make
using 5mm thick dark brown tinted float glass panels fixed to shutter
by means of Neoprene rubber beading or equivalent PVC beading
including silver grey matt finish outer frame, all necessary fixtures,
fastenings, locking devices, PVC weathering strips, nylon gliders,
etc. complete as per drawings, specifications and as directed by the
Engineer. The rate shall include supplying and fixing on site and
putting the glazed sliding windows in operation. All visible and
flush type locking devices shall be made of silver grey matt finish
anodised aluminium.

Three track ( ¾” series )

Sub frame
Rectangular tube - 100 x 25 x 1.2mm

Outer frame
Bottom track box section with water drainage arrangement
92 x 45.5 x 1.5

Top and sides

92 x 31.75 x 1.3

Shutter
Top and Bottom 40 x 18 x 1.25mm

Inter lock 40 x 18 x 1.1mm

Vertical Handle 40 x 18 x 1.25 50 Sq.m

Total of Section 'F':

Section 'G' Water Proofing:

G01 Providing and laying cement based water proofing treatment for
terraces with brick bats laid to slopes and grouted with cement
mortar mixed with proprietary products and weaving IPS layer on
top all laid as per manufacturer's specifications.

( A ten years guarantee is to be furnished for this treatment in

favour of Employer ) 900 Sq.m.

G02 Providing and laying cement based waterproofing treatment to

trenches, raft, walls by "Box Type Water proofing" laid as per
manufacturer's specification complete

i) on raff 75 mm thick 5 Sq.m.

ii) on vertical surfaces of walls 50 mm thick 5 Sq.m.

Page 9
 PART-I

S.No. Description QTY UNIT Rate AMOUNT

(RS.) (RS.)
G-03 Providing and fixing in position WATER STOPS 5 to 6mm thick of
approved make and shape along construction joints including
necessary arrangement for holding in position during concreting
necessary readjustment of reinforcement to suit proper positioning
of stop, including proper lapping, etc. complete as per drawings,
specifications and as directed by the Engineer.

a) 150mm wide PVC water stop. QRO RM.

b) 230mm wide PVC water stop. QRO RM.

Total of Section 'G':

Section 'H' Miscellaneous:

H01 Providing and erecting in position Pre-cast RCC work M20 grade
using 20 mm and downgraded stone metal aggregates including all
formwork, vibrating, compacting, curing, lifting hook arrangement
etc. complete but excluding cost of reinforcement paid for
separately.

a) 50 mm thick cover for trenches, ducts etc 10 Sq.m

b) 75 mm thick QRO Sq.m
c) 100 mm thick QRO Sq.m

H02 Providing and fixing in position 100 mm thick rain proof pre cast
RCC Jali block with 40 % openings in C.M.1:3 in including
necessary reinforcement, filling joints with 1:2 C.M, necessary
scaffolding, curing etc complete

QRO Sq.m

H03 Providing and fixing in position 25mm thick SHALITEX or

equivalent expansion joint filler Board dipped in bitumen including
cutting to required size etc. complete.

QRO Sq.m

H04 Providing and fixing in position to true horizontal line and level
false ceiling using 12mm thick semi perforated Nova Teak particle
board panel 600mm x 600mm and silver grey matt finish anodised
Aluminium framing consist of main bulbed tee 38 x 38 x 1.5mm
suspended from RCC slab or MS runners by means of 10 gauge GI
wire or 6mm MS bar, secondary cross tee (bulbed) 25 x 25 x
1.5mm, wall perimeter angle 25 x 25 x 1.5mm with MS hooks, nuts,
etc. including making necessary cut outs with additional Aluminium
frame work for fixing electrical fittings, air conditioning, diffusers,
etc. painting ceiling with two coats of plastic emulsion paint of
approved make and shade, all complete as per drawings.

Page 10
 PART-I

S.No. Description QTY UNIT Rate AMOUNT

(RS.) (RS.)
( In case of Aluminium grid work suspended from MS runners, the
same shall be paid under structural steel Item in the tender )
350 Sq.m

H05 Providing and fixing in position suspended metal framed plain false
ceiling using GI perimeter channels, GI Intermediate channels at
1200mm centers, GI hangers 25mm wide x 0.50mm thick, GI cross
channels at 600mm centers, connecting clips, 12.5mm thick tapered
edge GYPBOARD ( Conforming to IS : 2095, 1982 ) with 25mm
dry wall screws at 300mm centers including treating joints with
jointing compound and paper tape to give jointless finished surface
with one coat of Gypsum base top coat, painting the ceiling with two
coats of Acrylic Emulsion paint of approved make and shade, all
complete as per manufacturer’s specifications.

QRO Sq.m

Total of Section 'H':

Section 'I' Roads & Drainages:

Cutting in ordinary soil for 300 mm deep and carting away

excavated materials for filling in low lying areas including spreading
levelling and compacting it to a desired compaction or disposing it
I01 off to a lead of 750M etc including grass clearing,levelling etc and 6200 SQ.M
dewatering

Filling in Road sub-base with Gravel and sand 1:1mix in layers of

300 mm thick and rolling using vibromax TEN ton power roller
including wet rolling etc complete to given line and levels to acieve
I02 a compaction of 95% of standard proctor density test 6200 SQ.M

Providing and laying soling stone to a consolidated thickness of 230

mm thick properly handpacked interstices filled with spalls and
chips, and gravel surface formed and water rolled to required slopes
I03 and camber as specified and directed(RATE including DRY and 6200 SQ.M
WET Rolling)

Providing and laying WBM 100 mm thick using stone metal 50 mm

to 65 mm size with gravel over a stone soling including watering
I04 and rolling with 10 ton power roller to required slope and camber as 6200 SQ.M
specified and directed

Page 11
 PART-I

S.No. Description QTY UNIT Rate AMOUNT

(RS.) (RS.)
Providing and laying the concrete roads of total consolidated
thickness 180 mm using 20 mm and below size coarse aggregate
and using M250 grade of concrete including expansion joints,
contraction joints, providing the steel reinforcement as per the local
Govt. specifications and ceiling the expansion joints with ceilents as
directed by the engineer incaharge, including the form work to to
I05 cast the concrete as per the specified sizes of the panes and finally 6200 SQ.M
rolling to required slopes and camber etc complete as specified and
as directed.

Providing and laying the storm water drains in the block work
maintaining the slope as per the drawing and providing the man
holes as needed at 30 M interval and at the road crossing including
I06 plastering ,finishing --- etc complete as per the specifications and as
directed by the engineer in charge

a) 500 x 500 mm depth 600 RM

b) 600 x750 mm depth 600 RM
c) 750 x 1000 mm depth QRO RM
d) 1000 x 1200 mm depth QRO RM
I07 providing and fixing the hume pipes with proper levelling and
grading embedded in concrete as per the specifications

a) 300 dia 50 RM
b) 400 dia 50 RM
c) 500 dia QRO RM
d) 600 dia QRO RM

Total of Section 'I'

Page 12
 PART-II

M/S. JAYANSREE PHARMA PRIVATE LIMITED

AT VIZAG, A.P

TENDER
FOR
CONSTRUCTION OF SODIUM SULPHIDE PROJECT

PART-II : STRUCTURAL STEEL WORKS

PLANT AND NON-PLANT STRUCTURES

BILL OF QUANTITIES
Rev-00 - Dated: 03.01.19
Notes: 1.' Rates of all items must be filled in.

2. 'Quantities are probable and may vary.

3. Q.R.O. means Quote Rate Only.

NOTE:
Structural Steel Supplied by JPPL at agreed price.

S.No. Description QTY UNIT Rate AMOUNT

(RS.) (RS.)

Section 'I' - Structural Steel Work:

A01 Collecting from the stores, transporting to site, fabricating, welding

or bolting structural steel work, transporting to site, erecting and
fixing in position at all heights with two coats of synthetic enamel
oil paint over one coat of red oxide primer as per drawing,
specifications etc. complete and as directed

30 MT

A02 Collecting from the stores, transporting to site, fabricating and fixing
in position at al heights hand railing consisting of 40 mm dia M.S.
Class pipe in horizontals and verticals to give 1 m height railing
above finished floor level including all required fittings like bends,
couplings, caps etc. fixing or grouting to concrete, masonry, steel
surfaces and painted with two coats of synthetic enamel oil paint
over one coat of red oxide primer as per details and as directed by
the Engineer (Measurement for each running length of pipes and not
for full railing )

50 RM

A03 Collecting from the stores to site, fabricating and fixing in position
40 mm Thick MS Gratings for platforms/;staircases including
cutting to proper sizes, levellling and painting with two coats of
approved synthetic enamel oil paint and one coat of red oxide primer
at fabrication shop.

1 MT

Page 1
 PART-II

S.No. Description QTY UNIT Rate AMOUNT

(RS.) (RS.)
A04 Collecting from the stores, transporting to site, fabricating and
fixing in position MS Chequered plates (6/8 mm Thick) for
platforms/;staircases including cutting to proper sizes, levellling and
painting with two coats of approved synthetic enamel oil paint and
one coat of red oxide primer at fabrication shop.

1 MT
A05 Collecting from the stores, transporting to site, fabricating and
fixing in position in the concrete work/masonry work etc. inserts,
Embedments etc.
1 MT
A06 Providing, fabricating and fixing in position 2 mm thick Rola Deck
M.S.Profile as permanent, unremovable shuttering for roof slab at
any height resting on MS joists spaced at suitable intervals on steel
girders (Structural steel supplied by the Owner)

QRO Sq.m

Total of Section 'A':

Section 'J' Roofing & Accessories:

B01 Collecting from the stores, transporting to site, cutting, placing and
fixing in position at all heights ‘EVEREST’ make or equivalent
make asbestos cement corrugated sheets 6mm thick for following,
including accessories such as GI ‘J’ or ‘L’ 8mm dia bolts, seam
bolts, nuts, bituminous and GI washers, drilling holes by mechanical
hand drill with 200mm lap on steel purlins or runners, etc. complete
as per drawings, specifications and as directed by the Engineer.

a) In Roofing QRO Sq.m

b) In cladding QRO Sq.m

B02 Collecting from the stores, transporting to site, cutting, placing and
fixing to structural member GI Corrugated sheet in Roofing with
accessories consisting of poly cap, polymer washer, seal washer,
polycoated ‘J’ or ‘L’ bolts of required height etc all as per
manufacturer’s specification and as directed by the Engineer.

a) Corrugated sheet in Roofing 950 Sq.m

b) Adjustable Ridges in pairs 50 RM

B03 Providng and fixing in position PVC rain water pipes 2.5 Kg/
Sq.cm. rating of approved make with shoes, bends couplers, tees and
other specials as required including making hole in RCC / brick
work and grouting the same, jointing pipe with suitable synthetic
resin adhesive as per manufacturer’s specification, GI clamps, etc.
complete

a) 110mm dia pipe 50 RM

b) 160mm dia pipe 60 RM

Total of Section 'B':

Page 2