+86 755 8455 7891

PROS MINI Series Quick Start Guide [email protected] LAUNCH

Product Profile 1 Charging & Turning On

X-431 PROS MINI series are stylish Android-based diagnostic devices developed by LAUNCH. 1. Open the cover of the charging port located on the top of the tool.
They inherit from LAUNCH's advanced diagnosing technology and are characterized by covering
a wide range of vehicle models, featuring powerful functions, and providing precise test result.
Through simple wireless(BT) communication, they achieve full car model and full system vehicle
trouble diagnosis. They support WLAN connection, which enables you to access the Internet,
Charging port
update online and perform remote diagnosis etc, getting your job fixed faster and easier.

2. Connect one end of the included charging cable into the charging port of the tool, and
Display Tablet the other end to the power adaptor.
3. Plug the power adaptor into the AC outlet.
(Decodes the vehicle data sent from the
VCI device and indicates the test result.) 4. If the tool is being charged, a charging indicator displays . Once the indicator turns ,
charging is complete.
Vehicle's DLC 5. Pressing the POWER button will start the tool and enter the home screen.

Wireless(BT) communication

VCI Device
(Collects vehicle POWER button
data.)

VCI Device

The VCI(Vehicle Communication Interface) device works as a vehicle communication Note:On first use of the tool, or if the tool remains idle for a long period of time, there may be
interface device, which is designed to read the vehicle data and then send it to the tablet insufficient battery power to start the tool. Please charge for a minimum of 5 minutes before
via wireless (BT) communication. attempting to turn it on again. Please use the power adaptor included within the kit to charge the
tool. No responsibility can be assumed for any damage or loss caused as a result of using any power
adaptor other than the one supplied.

Notes: Notes:
2 Network Setup
Ÿ It only applies to passenger Ÿ It illuminates RED when the VCI
To enable you to surf the Internet, register App, launch remote diagnosis and update the
vehicles with 12V battery device is plugged into the vehicle’s diagnostic software etc, please follow the steps below to configure the network:
voltage. DLC.
1. On the home screen, tap “Settings” > WLAN.
Ÿ Remember to remove the VCI Ÿ BLUE indicates that the VCI device

is working in wireless (BT) 2. Slide the WLAN switch to ON, the system starts searching for available wireless
device from the DLC if it is
communication mode. networks.
not in use.
3. Select a wireless network. If the chosen network is open, the tablet will connect
Ÿ Please re-insert the VCI

device into the docking slot automatically, if the selected network is encrypted, a network password will need to be
on the back of the tablet after entered.
use to avoid loss. 4. When “Connected” appears, it indicates the tablet is properly connected to the
Internet.
3 Register & Update 4 Preparation & Connections
DLC Location
1. Launch App -> 2. Create an App Account -> 3. Activate VCI Connector -> 4. Download 1. Preparation
Diagnostic Software) 1) Switch the ignition on .
2 ) The vehicle battery voltage should be 9 - 18V.
1. Launch App: Tap the application icon on the 3 ) Throttle should be in a closed position.
Login
home screen and some illustrations that 2.Locate vehicle’s DLC socket
guide you through some of important Username The DLC(Data Link Connector) provides standard
operations appear. Scroll the screen and tap 16 pins and is generally located on driver’s side,
on “Start Now” to enter the Job menu. Tap Password about 12 inch away from the center of dashboard. Near center of dashboard
“Login” on the upper right corner of the See Figure DLC Location. If DLC is not equipped under dashboard, a label indicating its
screen. Login
position will be given. In case no DLC is found, please refer to Automobile Repair Manual.
a.For initial use, tap “New registration” to Retrieve password New Registration 3.Connection
open a sign-up page, refer to steps 2~4.
b.If you have an account, tap “Login” to Select the desired diagnostic connector according to the vehicle DLC type and then follow
the steps below to proceed:
login directly.
1.For vehicles equipped with universal OBD-II diagnostic socket, plug the VCI device into
c.If you forgot the password, tap “Retrieve
the vehicle’s DLC directly or use the OBD II extension cable to connect the VCI device
password” to retrieve it.
and the DLC.
2.For vehicles not equipped with OBD-II management system, do the following:
1). Select the corresponding non-16pin connector.
3. Activate VCI module: Input the 2. Create an Account: Fill in each 2). Plug the non-16pin end of the connector into the DLC socket, then connect the other
Product S/N and Activation Code field and tap “Register” to go to step end to the OBD I adaptor, and then tighten the captive screws.
(can be obtained from the password 3. (Note: To obtain more functions and 3). Connect the other end of the adaptor to the VCI device.
envelope), and then tap “Activate”. better service, please enter the real 4). To supply power to OBD I adaptor from:
information.) A. Battery Clamps Cable(optional): Connect one end of the battery clamps cable to
The right figure Product S/N Register Create an account vehicle's battery, and the other end to the power jack of OBD I adaptor, Or
displays the B. Cigarette Lighter Cable(optional): Connect one end of the cigarette lighter cable
location of the Username to vehicle's cigarette lighter receptacle, and the other end to the power jack of OBD
product S/N and I adaptor.
activation code. Activation Code Password

Confirm Password

Register Activate connector

Email 5 Start Diagnostics
Serial Number Select Country For new users, follow the sequence below to start a new diagnostic session.
Activation Code CAPTCHA CAPTCHA Tap “Tradition Select vehicle model Select software
Diagnose” (See Note*1) version (See Notes)
Activate
Register
> > Skip
Note*1: If “VINScan” is
performed, this step shall Select test function Select test system
not apply.
4. Download Diagnostic Software: Tap “Yes”
Register Finish registration Notes:
on the left figure to enter diagnostic software
Congratulations! You have successfully completed your * 1. To start diagnosing a vehicle, you have to activate the VCI device and download the
download screen. (Note: To download the
registration. Do you want to download the diagnostic diagnostic software. For details, please refer to Section 3 in this Quick Start Guide.
software now? software later, tap “No”. In this case, tap “Software
* 2. All software is updated from time to time. To enjoy more better capabilities and functions,
Yes Upgrade” on the function menu to download it.)
you are strongly suggested to keep synchronized with the latest version.
Tap “Update” to download and install the
No diagnostic software.(Note: Be sure that the tool
has a strong WLAN signal during downloading.) All pictures and illustrations are for reference purpose only, please refer to the actual tool.
This Quick Start Guide is subject to change without notice. For more detailed operations, please refer to
the user manual.