CertaDrive

LED driver

Datasheet

CertaDrive LED drivers – Linear HV non-isolated

CertaDrive 44W 200/350mA 125V 230V
9290 028 74480
Fixed current/voltage LED drivers for high volume LED propositions
The CertaDrive LED drivers are designed to fulfill the market need for essential lighting. The CertaDrive LED drivers offer basic specifications
such as specific current and voltage settings, optimal to operate CertaFlux LED modules. Life time of the driver is set at 50,000 hours. Philips
will extend the portfolio of CertaDrive LED drivers to match high volume CertaFlux LED line propositions as well as high volume opportunities
of other LED board manufactures.

Benefits Features Application

• Design freedom • Small dimensions • Waterproof luminaires
• Optimized to operate CertaFlux LED • Specific current and voltage • Recessed, surface and suspended
lines • 50,000 hours life time luminaires in offices
• 3-years warranty • Fast Time to Market

September 2021
Electrical input data

Specification item Value Unit Condition

Rated input voltage range 220...240 Vac Performance range
Rated input voltage 230 Vac
Rated input frequency range 50...60 Hz Performance range
Rated input current 0.23 A @ rated output power @ rated input voltage
Rated input power 48 W @ rated output power @ rated input voltage
Power factor 0.9 @ rated output power @ rated input voltage
Total harmonic distortion 20 % @ rated output power @ rated input voltage
Efficiency 91.8 % typical value @ 230V, full output power
Input voltage AC range 198...264 Vac Operational range
Input frequency AC range 45...66 Hz Operational range
Isolation input to output No

Electrical output data

Specification item Value Unit Condition

Regulation method Constant Current
Output voltage 75...125 Vdc
Output voltage max. 200 V Maximum output voltage (rms)
Output current 0.2 / 0.35 A Depends on the selected output LED- wire
Output current tolerance ± 8 %
Output current ripple LF ≤4 % Ripple = peak / average, < 3kHz. Rd = 50Ω
Output current ripple HF ≤ 15 %
Output PstLM ≤ 0.07
Output SVM ≤ 0.07
Output power 15...43.75 W

Electrical data controls input

Specification item Value Unit Condition

Control method Fixed

Wiring and Connections

Specification item Value Unit Type

Input wire cross-section 0.5...1.5 mm2 / AWG solid / stranded wire
Input wire strip length 8.5...9.5 mm
Output wire cross-section 0.5...1.5 mm2 / AWG solid / stranded wire
Output wire strip length 8.5...9.5 mm
Maximum cable length 2 m Total length of wiring including LED module, one way

2/7 CertaDrive 44W 200/350mA 125V 230V September 2021

Insulation

Insulation per IEC61347-1 Input Output Housing

Input Non Basic
Output Non Basic
Housing Basic Basic

Dimensions and weight

Specification item Value Unit Tolerance (mm)

Length (A1) 210 mm ± 0.3
Mounting hole distance (A2) 198.5 mm ± 0.3
Width (B1) 30 mm ± 0.5
Height (C1) 21 mm ± 0.5
Mounting hole diameter (D1) 4.1 mm ± 0.2
Mounting hole diameter (D2) 4.1 mm ± 0.2
Weight 130 gram

Logistical data

Specification item Value

Product name CertaDrive 44W 200/350mA 125V 230V
Logistic code 12NC 9290 028 74480
Pieces per box 20

Operational temperatures and humidity

Specification item Value Unit Condition

Ambient temperature -20...+50 ºC Higher ambient temperature allowed as long as Tcase-max is not
exceeded
Tcase-max 85 ºC Maximum temperature measured at Tcase-point
Tcase-life 75 ºC Measured at Tcase-point
Maximum housing temperature 110 ºC In case of a failure, inherent by design
Relative humidity 10...90 % Non-condensing

3/7 CertaDrive 44W 200/350mA 125V 230V September 2021

Lifetime

Specification item Value Unit Condition

Driver lifetime 50,000 hours Measured temperature at Tcase-point is Tcase-life. Maximum
failures = 10%

Storage temperature and humidity

Specification item Value Unit Condition

Ambient temperature -25...+85 ºC
Relative humidity 5...95 % Non-condensing

Programmable features

Specification item Available Default setting Condition

LED Module Temperature Protection (MTP) No
Constant Light Output (CLO) No
Corridor Mode No
DC emergency (DCemDim) No

Features

Specification item Value Condition

Open load protection Yes Automatic recovering
Short circuit protection Yes Automatic recovering
Over power protection Yes Automatic recovering
Hot wiring No
Suitable for fixtures with protection class I per IEC60598
Overtemperature protection No Automatic recovering
Overheating protection No

4/7 CertaDrive 44W 200/350mA 125V 230V September 2021

Inrush current

Specification item Value Unit Condition

Inrush current 14.2 A Input voltage 230V
Inrush peak width 222 µs Input voltage 230 V, measured at 50% height
Drivers / MCB 16A type B ≤ 36 pcs Indicative value

Please refer to the driver design in guide if you use other MCB-types.

Driver touch current / protective conductor current

Specification item Value Unit Condition

Typical Touch Current (ins. Class II) 0.7 mA peak Acc. IEC61347-1. LED module contribution not included

Surge immunity

Specification item Value Unit Condition

Mains surge immunity (diff. mode) 1 kV Acc. IEC61000-4-5. 2 Ohm, 1.2/50us, 8/20us
Mains surge immunity (comm. mode) 2 kV Acc. IEC61000-4-5. 12 Ohm, 1.2/50us, 8/20us

Application Info

Specification item Value

Approval marks CB / CCC / CE / ENEC / RCM / TISI
Ingress Protection classification (IP) 20
Application Indoor Linear
Mounting Type Built-in

5/7 CertaDrive 44W 200/350mA 125V 230V September 2021

Graphs

Operating window

Power factor versus output power

Efficiency versus output power

6/7 CertaDrive 44W 200/350mA 125V 230V September 2021

THD versus output power

©2021 Signify Holding, IBRS 10461, 5600 VB, NL. All rights reserved.
UK importer address: Signify Commercial UK Limited, 3, Guildford Business Park, GU2 8XG.

The information provided herein is subject to change without notice. Signify does not give any representation or warranty as to the accuracy or
completeness of the information included herein and shall not be liable for any action in reliance thereon. The information presented in this document
is not intended as any commercial offer and does not form part of any quotation or contract, unless otherwise agreed by Signify.

Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. All other trademarks are owned by Signify Holding or their
respective owners.
Date of release: September 13, 2021 v1

www.philips.com/oem