PRODUCED GAS RECYCLING

FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50

Datasheet for Manual Valves

CW2368055-EPF-PI-DAT-001

Issued for Yiwei Zhao

0 16/1/2024 Ying Ying Dafei Liang
Information
Prepared Revised Approved
REV Date Reason for Issue By By By
 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50

TABLE OF CONTENTS

1. GENERAL........................................................................................................................................ 4
1.1 Purpose.................................................................................................................................. 4
2. DESIGN............................................................................................................................................ 4
2.1 General................................................................................................................................... 4
2.2 Valve Coding rules.............................................................................................................. 6
2.3 Gear operator....................................................................................................................... 7
2.4 Specific Requirements for Various Valves...................................................................7
2.4.1 Specific Requirements For Ball Valves..................................................................... 7
2.4.2 Specific requirements for globe valves..................................................................... 8
2.4.3 Specific requirements for check valves.................................................................... 9
2.4.4 Abbreviations....................................................................................................................9
2.4.5 Code and Standards....................................................................................................... 9
3. CONFORMITIES AND DEVIATIONS........................................................................................10
4. SCOPE OF WORK....................................................................................................................... 11
4.1 Spare Parts and Special Tools.......................................................................................11
4.2 Data Required with Quotation........................................................................................11
5. TECHNICAL REQUIREMENTS................................................................................................. 12
5.1 Materials...............................................................................................................................12
5.2 Coating................................................................................................................................. 12
5.3 Material Certifications...................................................................................................... 12
5.4 Other Terms and Conditions.......................................................................................... 12
6. QUALITY CONTROL QUALITY ASSURANCE...................................................................... 12
7. IDENTIFICATION AND MARKING............................................................................................12
7.1 Valve Tagging.....................................................................................................................12
7.2 Identification and Marking Requirements...................................................................13
8. INSPECTION AND TEST............................................................................................................ 13
8.1 Inspection and Test Items...............................................................................................13
8.2 Non-destructive Examination for Cast and Forged Valve...................................... 14
 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50
8.3 Additional Non-destructive Examination for Valves................................................15
8.4 Procedure and acceptance standards shall be as follows.................................... 15
APPENDIX A---DOCUMENTS LIST SUBMITTED BY VENDOR.............................................17
APPENDIX B---TABLE OF COMPLIANCE..................................................................................18
APPENDIX C--- VALVE CLASSES SPECIFICATION............................................................... 19
 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50

1. GENERAL

1.1 Purpose

This datasheet, together with the referenced Specification for Piping Materials, describes the
minimum requirements for the manual and gear operated valves (Ball, Gate, Globe, Check, Butterfly
and Needle valves) to be used for Project.

2. DESIGN

2.1 General

Corrosion allowance for all valves with carbon steel bodies is 3mm.All valves with stainless steel
bodies have a corrosion margin of 0mm.
Valve pressure-temperature rating shall be in accordance with the applicable rating table for the
appropriate material group in ASME B16.34, and shall be full pressure rating design.

For Flanged end valves, Valve body welded with end flanges should not be used as much as
possible.

All material shall be new and the interior and exterior surface shall be free of dirt, sand, debris
and excessive rust.

If any impact testing or heat treatment is required for any of the materials as per ASTM / ASME
codes, VENDOR shall perform accordingly & shall meet the code requirements.

VENDOR shall be fully responsible to meet the design requirements indicated in this
specification, and guarantee the same.

1-1/2" and below valves should be forged; valves may be cast or forged for 2" and above.

All forgings shall be fine grain. Carbon steel used in the manufacture of bulk valves shall be
fully killed.

Soft seat and seals materials shall be suitable for the design conditions. Pressure-Temperature
rating chart or table for soft seats and seals shall be submitted by VENDOR.

Body seat rings of valves (gate, globe, needle, check and ball) shall be type seats. Soft seats
shall be fire safe design and performance tested per API 607, related test certificates and
reports shall be submitted by VENDOR.

Lifting lugs and valve supports should be provided for valves 8" and above. Lifting points on the
gear box or actuator shall never be used for lifting the actuated valve.
 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50
Uni-directional valves or valves with a preferred direction of flow shall have a flow direction
arrow cast or stamped on the body.

Trim materials, particularly stainless steels, should be carefully selected to prevent galling. Low
melting point alloys shall not be used.

Globe and gate valves shall have outside stem and yoke with bolted bonnets. Bonnets on check
valves shall be bolted.

All Valves having external threads on the Gear Operator, Gland, etc shall be provided with a
suitable thread protection device to protect the thread from the sand.

In higher temperature services, steel gate valves are recommended.

Valves with non-rising stem or valves with gear operators shall have position indicators, which
cannot be wrongly oriented, either on initial assembly or during subsequent dismantling and re-
assembly. These shall be clearly graduated and visible to show the open and closed position of
the fully assembled valve. The VENDOR shall include details of the proposed indicator at the bid
stage.

Stem design shall be blow out proof. The anti blowout stem configuration shall be capable of
withstanding the full internal pressure of the valve. Stem retention by means of threads is not
acceptable. The stem retainer ring or collar shall be integral with the stem.

Antistatic design - When valves are provided with soft seats, their design shall ensure electric
continuity between the obturator and the body, by means of an antistatic device.

For all metal to metal seated valves, the maximum hardness of the body seats, body back seats
and the closure (gate, wedge, disc, blade, etc.) seating surfaces shall be suitable for the required
service. There shall be minimum hardness differential of 50 BHN between body and closure
seating surfaces on stainless steel valves and 20 to 30 BHN for carbon steel valves.

Valves shall be designed to operate freely after the stem has remained in one position for an
extended period of service or till the next periodic maintenance.

Weld overlay on valve trims shall be performed as per ASME Section VIII Div. 1 and Welding
Procedures to be used shall be qualified in accordance with ASME Section IX.

Separate removable valve parts shall be positively secured against loosening. Spring tension pins
are prohibited for locking of internal valve components.

Valve painting requirements see Specification for Painting(CW2368055-EPF-PI-SPC-005).

 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50
2.2 Valve Coding rules

Valves are identified using as shown below

Example B G R - 1 P F

Number 1 2 3 4 5 6

First number:Type

Ball valve B Globe valve J

Check valve C

Second number:Actuator

Gear G Handwheel/Lever H

When check valve ,second number can be omitted.

Third number:Connection Type

Thread T Flange(RJ) J

Flange(RF) R Flange(FF) F

Fourth number:Pressure Rating

Class 150 1 Class 300 3

Class 600 6 Class 800 8

Class 900 9 Class1500 15

Class 2500 25

Fifth number:Material

C A105/A216 WCB P F304/CF8

X F316/316L

Sixth number:Additonal Note

Ball valve Ball valve

F R
(Full Bore ) (Reduce Bore )
 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50

DBB D

Senventh number:Additonal Note

valve
(Used for produced W
oil&water)

2.3 Gear operator

Gear operators shall be of a design and so installed on the valve that normal valve
operation is not impaired and all gear-operated valves shall be capable of being fully
opened and closed.

Table-1: Manual Gear Operator Requirements for Valves

Valve Type Rating Gear Operator

Class 150
8" & Larger
Class 300
Ball Valves
Class 600 6" & Larger
Class 2500 4" & Larger
Class 150
14" & Larger
Gate Valves Class 300
Class 600 10" & Larger
Class 2500 8" & Larger
Class 150
8" & Larger
Class 300
Globe Valves 6" & Larger
Class 600

Class 2500 4" & Larger

2.4 Specific Requirements for Various Valves

2.4.1 Specific Requirements For Ball Valves

Effective API 6D certification shall be submitted by VENDOR.

The design of ball valves for sizes 1-1/2" and below shall be according to API 608 and for sizes 2"
and above shall be according to API 6D.
 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50
The ball and stem of all ball valves shall be of solid construction of the material specified. Fabricated
type ball (i.e. with welded in line) are not acceptable.

Ball valves shall be designed to seal in both directions, i.e. bi-directional, against all pressures up to
the maximum service pressure rating for the class unless specified otherwise in the material
requisition or the valve data sheet.

The design of valve seal / seat arrangement shall be such that the soft seal shall not displace or get
out of shape both under pressure and during the depressurization of the piping system.

Trunnion ball valve shall have injection points and drain.

The design of ball as either floating or trunnion depends on valve size and rating. Generally small
bore valves can be accepted as floating ball design. Table-2 below serves as a guide for the design
of ball as either floating or trunnion mounted design:

Table-2: Guide for the Design of Ball

Rating Floating Trunnion

Class 150
½” to 2” 3” and larger
Class 300

Class 600 ½” to 2” 3” and larger

Class 900 ½” to 2” 3” and larger

Class 1500 ½” to 2” 3” and larger

Class 2500 ½” to 1-1/2” 2” and larger

Support Legs to be provided for valves 8" and above to facilitate the support beneath the valve.

2.4.2 Specific requirements for globe valves

The design of globe valves of size 1-1/2” and below shall be to API 602 and 2” & above shall be to
BS 1873, unless noted otherwise on the valve data sheets.

All globe valves shall be suitable for throttling duties. An arrow, to indicate the correct flow directions
shall be part of the body casting or forging or shall be embossed on the valve body.

Gear operated globe valves shall have operators of a design that will allow the valve to be set in
intermediate throttling positions for long periods without having to lash down the hand wheel.

All globe valves shall be provided with back seating facility.

 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50
2.4.3 Specific requirements for check valves

The design of check valves of size 1-1/2” and below shall be to API 602 and 2” & above shall be to
API 594 unless noted otherwise on the valve data sheets.

The design, construction and material requirements shall be as specified or in the valve data sheet.

Dual plate check valves shall be of retainer less design. Flow direction of check valves shall be
marked on body with permanent arrow.

2.4.4 Abbreviations

API American Petroleum Institute

ASTM American Society for Testing and Materials

ASME American Society of Mechanical Engineers

DGM General Directorate of Mines

MR Material Requisition

MTC Material Test Certificate

VDRF VENDOR Drawing and Data Requirement Form

MTO Material Take Off

NDT Non-Destructive Test

PWHT Post Weld Heat Treatment

DGM General Directorate of Mines

2.4.5 Code and Standards

API STD 594 Check Valves: Flanged, Lug, Wafer, and Butt-welding

API STD 598 Valve Inspection & Testing

API STD 602 Steel Gate, Globe and Check Valves for sizes NPS 4 (DN100) and
smaller for the Petroleum and Natural Gas Industries
 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50

API STD 607 Fire testing for Soft-Seated quarter-turn valves

API STD 608 Metal Ball valves-Flanged, Threaded and Welding Ends

API SPEC 6D Specification for pipe line valves (Gate, Plug, Ball and Check valves)

API SPEC 6FA Specification for Fire Testing of Valves

BS 1873 Specification for Steel globe and globe stop and check valves (flanged
and butt-welding ends) for the petroleum, petrochemical and allied
industries

ASME B16.34 Valves - Flanged,Threaded,and Welding End

NACE MR Petroleum,petrochemical,and natural gas industries-Materials for use

0175/ISO15156 in H2S-containing environments in oil and gas production

Note: This list covers the majority of references, but it is not exhaustive.

3. CONFORMITIES AND DEVIATIONS

Exception or deviation per each requisition shall be clarified one by one in vendor’s proposal. Any
exceptions, deviations, alternatives and omissions shall be clearly identified in the exception and
deviation list . This list shall be filled out and submitted by vendor together with vendor’s proposal at
bid stage for purchaser’s review and approval.

Purchaser has no responsibility to discover any deviations entered in Vendor’s proposal other than
the deviations specifically listed in the form and those deviations which are not listed in the
consolidated deviation list shall be disregarded.

No deviations from the requirements of this specification are allowed after issue of the letter of intent.

Compliance with the material requisition does not relieve vendor responsibility to furnish proper
design of commodity and mechanically suited to meet the operating quarantines at specified service
condition indicated in the data sheets and/or specification.

As an alternative to the quotation submitted in accordance with the enclosed documents, it is

purchaser’s objective to achieve the commercially most attractive solution for the entire required
scope within the requirements of this inquiry. Bidder is therefore requested to carefully analyze the
enclosed documents and to submit additionally an alternative quotation highlighting cost affected
items considering the codes standards and Manufacturer’s standards only.
 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50
Purchaser's acceptance of vendor’s drawings or data with or without comments does not relieve the
Vendor of the responsibility of complying with all terms, conditions, codes, standards, requirements
of this requisition and project specifications. Purchaser reserves the right to review and comment on
drawings that have previously been accepted with or without comments.

4. SCOPE OF WORK

The scope of work is to supply Manual Valve in the quantity and type as described in the attached
MTO / Datasheets. This scope of work, together with the referenced specifications and data sheets,
describes the minimum requirements for the Manual Valve.

4.1 Spare Parts and Special Tools

The Vendor must provide with the list of parts recommended spares for two years of operations. If
need,Spare parts relating to the startup and commission will be supplied by the Vendor.

Spare operational parts will be supplied by Vendor to have their availability on site before
preparation for commissioning of the facility if need.

The inspection, receipt, storage and protection of spare parts and any special tools shall be in
accordance with conditions required by the Employer.

4.2 Data Required with Quotation

The Vendor shall provide the following along with the bid:

●Comments / Deviations / Exceptions taken by the Vendor with respect to Project Specifications, Data
Sheets, Codes, Standards and Regulations shall be explained with technical justification for
evaluation;

●Detailed description of scope of supply;

●Valid API 6D, API 607 / API 6FA certificates;

●Valid pressure piping components construction organization safety registered certification by national
authority agency (TS certification, for Chinese manufacture only) & related reports and ISO 9001
certification shall be submitted;

● Proposed manufacturing / delivery schedule;

● Proposed Quality Assurance/ Safety Plan;

●Inspection and Test Plan;

● Recommended start-up and commissioning spare parts;

 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50
● List of references;

● List of proposed Subvendor (if any).

5. TECHNICAL REQUIREMENTS

5.1 Materials

Materials selection for Manual Valves refers to MTO/Data sheet/Specification.

5.2 Coating

Coating for valves should be performed as Specification for Painting(CW2368055-EPF-PI-SPEC-

0005).Austenitic stainless steel valves should not be coated.

5.3 Material Certifications

The VENDOR shall furnish manufacturer's material test reports showing actual results of chemical
analysis and mechanical tests in compliance with the referenced specification. Valve materials shall
be certified in accordance to BS EN10204 type 3.1.

5.4 Other Terms and Conditions

The dimensions, heat treatment, and other related requirements shall comply with ASME series
standards.

Emergence seat sealant injection port, vent and drain port for trunnion ball valves should be provided.

Ball valves shall be designed as long pattern type.

Gear drives shall be enclosed in weatherproof boxes, packed with suitable lubricant, equipped with
one or more grease fittings for packing in-situ, and equipped with open/close end-stops.

6. QUALITY CONTROL QUALITY ASSURANCE

The Vendor shall maintain and use a Quality System which is based on ISO 9001 to control the work.
If the Vendor selects sub-contracts for part of the work, he shall ensure that only those Subvendor's or
Vendor's are used who can demonstrate that they operate Quality Systems based on ISO 9001. The
Vendor shall give his Subvendor or Vendors assistance in attaining the required standard, if
necessary. This shall not relieve the Vendor of his responsibility for the quality of the finished work.
Contractor reserve the right to audit the Vendor 'S Quality System.

7. IDENTIFICATION AND MARKING

7.1 Valve Tagging

 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50
All valves shall be tagged using a stainless steel SS. 316 tag, hard stamped with the size and number
as specified on the Material Requisition. Tag shall be securely attached with multi-stand SS 316 wire,
such that the Tag cannot be easily removed. This tagging should be separated from any nameplate
affixed to the valves.

7.2 Identification and Marking Requirements

The following requirements supplement the marking and identification requirements relevant reference
codes, standards and material specification, the marking should be in English and the size should be
in NPS.

The following markings are required as a minimum:

● Manufacture's Name, Model Number & Year of Manufacturing; Standards, Valve Coding;

● Size;

● Rating;

● Body Material;

● Trim Material;

● Flange Facing Type;

● Body Seat Material;

Etc.

The nameplate and tagging drawings should be submitted for approval.

8. INSPECTION AND TEST

Manufacturing data and records, such as material test reports or certificates, results of non-
destructive examinations, records of visual examinations and dimensional inspection, and etc.
shall be available for inspection by purchaser and/or it's representative upon request.

8.1 Inspection and Test Items

The following inspection and test template, shown on Table 8.1-1, shall be as a minimum and
completed by Vendor.The final ITP

shall be subject to the approval of Employer/Contractor.

 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50
Table 8.1-1

Applicable Key
Description of Verifying
Item Spec/Procedu Inspectio Inspection Point REMARK
Activity Doc
re/Code n Items

8.2 Non-destructive Examination for Cast and Forged Valve

Non-destructive examination of valves shall be performed in accordance with the requirements of

Table 8.2-2.

Table 8.2-2

Cast Valves Forged Valves

RT MT or PT MT or PT
Note (1), (2), (3), 5) Note (1), (2), (4) Note (1), (2), (4)

Carbon Steel Rating class 900 & over Rating class 900 & over Rating class 1500 & over

Al-killed Carbon Steel (6) Rating class 600 & over Rating class 150 & over Rating class 300 & over

L Rating class 150 & over Rating class 150 & over Rating class 300 & over
Austenitic Stainless M Rating class 900 & over Rating class 900 & over Rating class 1500 & over

H Rating class 600 & over Rating class 600 & over Rating class 600 & over
Notes:

(1) Examination shall be performed on minimum one valve per one lot.

(2) Lot means the valves of same size, rating and type produced from same heat of material.

(3) RT shall be required for all critical area specified in Para. 8.3.1 of ASME B16.34, including
bevel surface of butt-welding end with class 900 and over.

(4) MT or PT shall be required for all accessible interior and exterior surfaces including all
welds of body and bonnet.

(5) UT may be applied instead of RT with Purchaser’s approval.

Abbreviation

RT: Radiographic Test

 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50
L: Low Temperature Service (below -100℃)

MT: Magnetic Particle Test

M: Medium Temperature Service (427℃and under)

PT: Liquid-Penetrate Test

H: High Temperature Service (above 427℃)

UT: Ultrasonic Test

8.3 Additional Non-destructive Examination for Valves

Additional non-destructive examination for valves shall be performed in accordance with the
requirements of Table 8.3-3

Table 8.3-3

Inspection Groove Weld Fillet Weld (2) Butt-Weld End Weld Overlay

RT 100% (1) - 100% -

MT or PT 100% (3) 100% (3) 100% 100%

Notes:

(1)Where RT is impractical, other appropriate non-destructive examination, such as UT shall be

done.

(2)Fillet weld includes socket and seal welds, and attachment for slip-on flanges and branch
reinforcement.

(3)MT or PT shall be performed for both root pass and final weld surface.

8.4 Procedure and acceptance standards shall be as follows.

Minimum examination of steel materials shall conform to the procedures and acceptance
standards outlined in Table 8.4-4.
 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50
Table 8.4-4

Examination Standards and Specifications

Radiographic Test (RT) ASTM E 94 Note (1)

Magnetic Particle Test (MT) ASTM E709 Note (2) ASTM A275 Note (2)

Liquid-Penetrate Test (PT) ASTM E165 Note (3)

Ultrasonic Test (UT) ASTM A609 Note (4) ASTM A388

Note (4)

Notes:

(1)Where the methods according to ASTM E 94 are applied, acceptance standards shall be given in
ASME B16.34 APPENDIX I.

(2)Acceptance standards shall be given in ASME B16.34 APPENDIX II.

(3)Acceptance standards shall be given in ASME B16.34 APPENDIX III.

(4)Acceptance standards shall be given in ASME B16.34 APPENDIX IV.

Minimum examination of welds shall conform to the procedures and acceptance standards outlined in
Table 8.4-5.

Table 8.4-5

Examination Standards and Specifications

Radiographic Test (RT) ASME Code Sec. VIII Div.1 UW 51

Magnetic Particle Test (MT) ASME Code Sec. VIII Div. 1 Appendix 6

Liquid-Penetrate Test (PT) ASME Code Sec. VIII Div. 1 Appendix 8

Ultrasonic Test (UT) ASME Code Sec. VIII Div. 1 Appendix 12

 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50

APPENDIX A---DOCUMENTS LIST SUBMITTED BY VENDOR

● Inspection and Test Plan

● Manufacture, Quality Surveillance and Delivery Schedule

● List of any and all exceptions/deviations

● Document Index and Submission Schedule

● NDE Reports (if applicable)

● Hydrotest Reports

● Surface preparation and Painting/Galvanizing Reports

● Material Certificates / Mill Certificates

● Heat Treatment Reports (if applicable)

● Final documentation

● Project Quality Plan, QC Procedures

Notes:

●The list will be disscussed by design, quality, and procurement engineers of Contractor in
consultation with the Vendor before the PO issued and subject for approval of Employer.

●All the documents shall be in English language;

●All deliverables shall be submitted by official Transmittals;

●The submitted documents shall be accurate, checked and signed by responsible Engineer(s).

●All revisions to documents must be clouded and identified with the revision number contained within
a triangle placed beside the cloud

●The above item is a minimum requirement.

 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50
APPENDIX B---TABLE OF COMPLIANCE

If VENDOR has no exceptions to any aspects of this Engineering Requisition and its associated
references, attachments and Appendices, then VENDOR shall specifically state that their bid is in Full
Compliance by either ticking the box (for full compliance) or completing the table below where full
compliance is not offered.

Bid is in Full Compliance (VENDOR to tick box is in Full Compliance)

All be provided by completing the table below.

S.No. Document Paragraph / Deviation / Justification Jereh

Number / Clause Number Exceptions Remarks
Document Title (and Page
Number)

Notes:

Exception: VENDOR cannot meet the requirement specified.

Format:

- VENDOR shall prepare A4 format of the above table and shall clearly state any exceptions. If
exceptions are not stated, it shall be interpreted by Contractor as full compliance.

- Each page of the form shall be signed and stamped by VENDOR.

 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50

APPENDIX C VALVE CLASSES SPECIFICATION

This document should be read in conjunction with other project specifications as mentioned below:

CW2368055-EPF-PI-BOD-001 Piping Design Basis

CW2368055-EPF-PI-SPEC-003 Specification for Piping Materials

CW2368055-EPF-PI-SPEC-005 Specification for Painting

 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50

Valve Specification

Test and Inspection

Pressure Rating CL800
API 598

Design Code API 608

Carbon Steel
Body Material
Forged-ASTM A105 Hot Dipped Galvanized

Trim Material Ball:316L, Stem: A182 F6a, Seat and Seal: RPTFE

Bolting Bolt to ASTM A193-B7, Nut to ASTM A194-2H

End Connection NPT(F) ASME B16.11

Temperature
-29~200°C
Limitations

Valve Operation Lever

Body Construction Full Bore, Floating

Trim Anti-Static device & Fire-Resistance StructureAPI 607&Anti-Blow off

Type/Function Structure

Notes:
Packing Material:
1. Valves to be Asbestos Free.
Graphite/MFR’s Advice
2. Face to face dimensions to ASME B16.10.
3. Hydraulic Test According to API 598.
4. Valves Shall Have Position Indicator Showing Open
Gasket Material:
and Close Positions.
Graphite/MFR’s Advice
5. Valve Nameplate Shall be 316SS.
6. With A Lockable Device.

Nominal Size Range

1/2”-2”

Valve Type Valve Coding

Ball BHT-8CF
 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50

Valve Specification

Test and Inspection

Pressure Rating CL150
API 598

Design Code API 608

Body Material Carbon Steel Forged-ASTM A105N

Trim Material Ball: 316L, Stem: A182 F6a, Seat and Seal: RPTFE

Bolting Bolt to ASTM A193-B7M, Nut to ASTM A194-2HM

End Connection RF ASME B16.5

Temperature
-29~200°C
Limitations

Valve Operation Lever

Body Construction Full Bore, Floating

Trim Anti-Static device & Fire-Resistance StructureAPI 607&Anti-Blow off

Type/Function Structure

Notes:
Packing Material:
1.Valves to be Asbestos Free.
Graphite/MFR’s Advice
2.Face to face dimensions to ASME B16.10.
3.Hydraulic Test According to API 598.
4. Valves Shall Have Position Indicator Showing Open
and Close Positions.
Gasket Material:
5.Valve Nameplate Shall be 316SS.
Graphite/MFR’s Advice
6. With A Lockable Device.
7.All Material Shall Meet The Requirements OF NACE MR
0175/ISO15156.

Nominal Size Range

1/2"-2”

Valve Type Valve Coding

Ball BHR-1CF
 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50

Valve Specification

Test and Inspection

Pressure Rating CL150
API 598

Design Code API 6D

Body Material Carbon Steel Cast-ASTM A216-WCB

Trim Material Ball: 316L, Stem: A182 F6a, Seat and Seal: RPTFE

Bolting Bolt to ASTM A193-B7M, Nut to ASTM A194-2HM

End Connection RF ASME B16.5

Temperature
-29~200°C
Limitations

Valve Operation Lever

Body Construction Full Bore, Trunnion

Trim Anti-Static device & Fire-Resistance StructureAPI 607&Anti-Blow off

Type/Function Structure

Notes: Packing Material:

1. Valves to be Asbestos Free. Graphite/MFR’s Advice
2.Face to face dimensions to ASME B16.10.
3. Hydraulic Test According to API 598.
4.Valves Shall Have Position Indicator Showing Open
and Close Positions. Gasket Material:
5.Valve Nameplate Shall be 316SS. Graphite/MFR’s Advice
6.With A Lockable Device.
7.All Material Shall Meet The Requirements OF NACE MR
0175/ISO15156.
Nominal Size Range

3”-6”

Valve Type Valve Coding

Ball BHR-1CF
 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50

Valve Specification

Test and Inspection

Pressure Rating CL150
API 598

Design Code API 6D

Body Material Carbon Steel Cast-ASTM A216-WCB

Trim Material Ball: 316L, Stem: A182 F6a, Seat and Seal: RPTFE

Bolting Bolt to ASTM A193-B7M, Nut to ASTM A194-2HM

End Connection RF ASME B16.5

Temperature
-29~200°C
Limitations

Valve Operation Lever

Body Construction Reduced Bore,Trunnion

Trim Anti-Static device & Fire-Resistance StructureAPI 607&Anti-Blow off

Type/Function Structure

Notes:
Packing Material:
1.Valves to be Asbestos Free.
Graphite/MFR’s Advice
2.Face to face dimensions to ASME B16.10.
3. Hydraulic Test According to API 598.
4.Valves Shall Have Position Indicator Showing Open
and Close Positions.
Gasket Material:
5.Valve Nameplate Shall be 316SS.
Graphite/MFR’s Advice
6.With A Lockable Device.
7.All Material Shall Meet The Requirements OF NACE MR
0175/ISO15156.

Nominal Size Range

3”-6”

Valve Type Valve Coding

Ball BHR-1CR
 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50

Valve Specification

Test and Inspection

Pressure Rating CL150
API 598

Design Code API 608

Body Material Stainless Steel Forged-ASTM A182 F304

Trim Material Ball: 304, Stem: 304, Seat and Seal: PEEK

Bolting Bolt to ASTM A320-B8M CL.2, Nut to ASTM A194-8M

End Connection RF ASME B16.5

Temperature
-46~250°C
Limitations

Valve Operation Lever

Body Construction Full Bore, Floating

Trim Anti-Static device & Fire-Resistance StructureAPI 607&Anti-Blow off

Type/Function Structure

Notes:
Packing Material:
1.Valves to be Asbestos Free.
Graphite/MFR’s Advice
2.Face to face dimensions to ASME B16.10.
3.Hydraulic Test According to API 598.
4. Valves Shall Have Position Indicator Showing Open
and Close Positions.
Gasket Material:
5.Valve Nameplate Shall be 316SS.
Graphite/MFR’s Advice
6. With A Lockable Device.
7.All Material Shall Meet The Requirements OF NACE MR
0175/ISO15156.

Nominal Size Range

1/2"-2”

Valve Type Valve Coding

Ball BHR-1PF
 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50

Valve Specification

Test and Inspection

Pressure Rating CL150
API 598

Design Code API 6D

Body Material Stainless Steel Cast-ASTM A351 CF8

Trim Material Ball: 304, Stem: 304, Seat and Seal: PEEK

Bolting Bolt to ASTM A320-B8M CL.2, Nut to ASTM A194-8M

End Connection RF ASME B16.5

Temperature
-46~250°C
Limitations

Valve Operation Lever

Body Construction Full Bore, Trunnion

Trim Anti-Static device & Fire-Resistance StructureAPI 607&Anti-Blow off

Type/Function Structure

Notes:
Packing Material:
1.Valves to be Asbestos Free.
Graphite/MFR’s Advice
2.Face to face dimensions to ASME B16.10.
3.Hydraulic Test According to API 598.
4. Valves Shall Have Position Indicator Showing Open
and Close Positions.
Gasket Material:
5.Valve Nameplate Shall be 316SS.
Graphite/MFR’s Advice
6. With A Lockable Device.
7.All Material Shall Meet The Requirements OF NACE MR
0175/ISO15156.

Nominal Size Range

3"-4”

Valve Type Valve Coding

Ball BHR-1PF
 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50

Valve Specification

Test and Inspection

Pressure Rating CL150
API 598

Design Code API 6D

Body Material Stainless Steel Cast-ASTM A351 CF8

Trim Material Ball: 304, Stem: 304, Seat and Seal: PEEK

Bolting Bolt to ASTM A320-B8M CL.2, Nut to ASTM A194-8M

End Connection RF ASME B16.5

Temperature
-46~250°C
Limitations

Valve Operation Lever

Body Construction Reduced Bore,Trunnion

Trim Anti-Static device & Fire-Resistance StructureAPI 607&Anti-Blow off

Type/Function Structure

Notes:
Packing Material:
1.Valves to be Asbestos Free.
Graphite/MFR’s Advice
2.Face to face dimensions to ASME B16.10.
3.Hydraulic Test According to API 598.
4. Valves Shall Have Position Indicator Showing Open
and Close Positions.
Gasket Material:
5.Valve Nameplate Shall be 316SS.
Graphite/MFR’s Advice
6. With A Lockable Device.
7.All Material Shall Meet The Requirements OF NACE MR
0175/ISO15156.

Nominal Size Range

3"-4”

Valve Type Valve Coding

Ball BHR-1PR
 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50

Valve Specification

Test and Inspection

Pressure Rating CL150
API 598

Design Code BS 1873

Carbon Steel
Body Material
Cast-ASTM A216-WCB

Trim Material Trim: 13Cr/STL

Bolting Bolt to ASTM A193-B7M, Nut to ASTM A194-2HM

End Connection RF ASME B16.5

Temperature
-29~200°C
Limitations

Valve Operation Handwheel

Body Construction Bolted Bonnet, Rising Stem Outside Screw and Yoke

Trim Type/Function Plug

Notes: Packing Material:

1. Valves to be Asbestos Free. Graphite/MFR’s Advice
2. Face to face dimensions to ASME B16.10.
3. Hydraulic Test According to API 598.
4. Valve Nameplate Shall be 316SS. Gasket Material:
5. Valve to be provided sand prevention component Graphite/MFR’s Advice
6.All Material Shall Meet The Requirements OF NACE MR
0175/ISO15156.

Nominal Size Range

2"-6”

Valve Type Valve Coding

Globe JHR-1C
 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50

Valve Specification

Test and Inspection

Pressure Rating CL150
API 598

Design Code BS 1873

Stainless Steel
Body Material
Cast-ASTM A351 CF8

Trim Material Trim: 304/STL

Bolting Bolt to ASTM A320-B8M CL.2, Nut to ASTM A194-8M

End Connection RF ASME B16.5

Temperature
-46~250°C
Limitations

Valve Operation Handwheel

Body Construction Bolted Bonnet, Rising Stem Outside Screw and Yoke

Trim Type/Function Plug

Notes: Packing Material:

3. Valves to be Asbestos Free. Graphite/MFR’s Advice
4. Face to face dimensions to ASME B16.10.
3. Hydraulic Test According to API 598.
4. Valve Nameplate Shall be 316SS. Gasket Material:
5. Valve to be provided sand prevention component Graphite/MFR’s Advice
6.All Material Shall Meet The Requirements OF NACE MR
0175/ISO15156.

Nominal Size Range

2"-6”

Valve Type Valve Coding

Globe JHR-1P
 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50

Valve Specification

Test and Inspection

Pressure Rating CL150
API 598

Design Code API 594

Carbon Steel
Body Material
Cast-ASTM A216 WCB

Trim Material Trim: 13Cr/STL

Bolting Bolt to ASTM A193-B7M, Nut to ASTM A194-2HM

End Connection RF ASME B16.5

Temperature
-29~200°C
Limitations

Valve Operation

Body Construction Wafer Type

Trim
Dual Plate
Type/Function

Notes: Packing Material:

1. Valves to be Asbestos Free.
Graphite/MFR’s Advice
2. Hydraulic Test According to API 598.
3. Valve Nameplate Shall be 316SS. Gasket Material:
4.All Material Shall Meet The Requirements OF NACE MR Graphite/MFR’s Advice
0175/ISO15156.

Nominal Size Range

2”-2”

Valve Type Valve Coding

Wafer Check, D-PL CR-1C
 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50

Valve Specification

Test and Inspection

Pressure Rating CL150
API 598

Design Code API 608

Body Material Carbon Steel Forged-ASTM A105N

Trim Material Ball: 316L, Stem: 316, Seat and Seal: RPTFE

Bolting Bolt to ASTM A193-B7M, Nut to ASTM A194-2HM

End Connection RF ASME B16.5

Temperature
-29~200°C
Limitations

Valve Operation Lever

Body Construction Full Bore, Floating

Trim Anti-Static device & Fire-Resistance StructureAPI 607&Anti-Blow off

Type/Function Structure

Notes:
Packing Material:
1.Valves to be Asbestos Free.
Graphite/MFR’s Advice
2.Face to face dimensions to ASME B16.10.
3.Hydraulic Test According to API 598.
4. Valves Shall Have Position Indicator Showing Open
and Close Positions.
Gasket Material:
5.Valve Nameplate Shall be 316SS.
Graphite/MFR’s Advice
6. With A Lockable Device.
7.All Material Shall Meet The Requirements OF NACE MR
0175/ISO15156.

Nominal Size Range

1/2"-2”

Valve Type Valve Coding

Ball BHR-1CFW
 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50

Valve Specification

Test and Inspection

Pressure Rating CL150
API 598

Design Code API 6D

Body Material Carbon Steel Cast-ASTM A216 WCB

Trim Material Ball: 316L, Stem: 316, Seat and Seal: RPTFE

Bolting Bolt to ASTM A193-B7M, Nut to ASTM A194-2HM

End Connection RF ASME B16.5

Temperature
-29~200°C
Limitations

Valve Operation Lever

Body Construction Full Bore, Trunnion

Trim Anti-Static device & Fire-Resistance StructureAPI 607&Anti-Blow off

Type/Function Structure

Notes:
Packing Material:
1.Valves to be Asbestos Free.
Graphite/MFR’s Advice
2.Face to face dimensions to ASME B16.10.
3. Hydraulic Test According to API 598.
4.Valves Shall Have Position Indicator Showing Open
and Close Positions.
Gasket Material:
5.Valve Nameplate Shall be 316SS.
Graphite/MFR’s Advice
6.With A Lockable Device.
7.All Material Shall Meet The Requirements OF NACE MR
0175/ISO15156.

Nominal Size Range

3”-6”

Valve Type Valve Coding

Ball BHR-1CFW
 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50

Valve Specification

Test and Inspection

Pressure Rating CL150
API 598

Design Code API 6D

Body Material Carbon Steel Cast-ASTM A216 WCB

Trim Material Ball: 316L, Stem: 316, Seat and Seal: RPTFE

Bolting Bolt to ASTM A193-B7M, Nut to ASTM A194-2HM

End Connection RF ASME B16.5

Temperature
-29~200°C
Limitations

Valve Operation Lever

Body Construction Reduced Bore,Trunnion

Trim Anti-Static device & Fire-Resistance StructureAPI 607&Anti-Blow off

Type/Function Structure

Notes:
Packing Material:
1.Valves to be Asbestos Free. Graphite/MFR’s Advice
2.Face to face dimensions to ASME B16.10.
3. Hydraulic Test According to API 598.
4.Valves Shall Have Position Indicator Showing Open
and Close Positions.
Gasket Material:
5.Valve Nameplate Shall be 316SS.
Graphite/MFR’s Advice
6.With A Lockable Device.
7.All Material Shall Meet The Requirements OF NACE MR
0175/ISO15156.

Nominal Size Range

3”-6”

Valve Type Valve Coding

Ball BHR-1CRW
 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50

Valve Specification

Test and Inspection

Pressure Rating CL300
API 598

Design Code BS 1873

Body Material Carbon Steel Cast-ASTM A216 WCB

Trim Material Trim: 316L,Stem:316

Bolting Bolt to ASTM A193-B7M, Nut to ASTM A194-2HM

End Connection RF ASME B16.5

Temperature
-29~200°C
Limitations

Valve Operation Handwheel

Body Construction Bolted Bonnet, Rising Stem Outside Screw and Yoke

Trim Type/Function Plug

Notes: Packing Material:

1. Valves to be Asbestos Free. Graphite/MFR’s Advice
2. Hydraulic Test According to API 598.
3. Valve Nameplate Shall be 316SS.
4. Valve to be provided sand prevention component Gasket Material:
5.All Material Shall Meet The Requirements OF NACE MR Graphite/MFR’s Advice
0175/ISO15156.
6.Face to face dimensions to ASME B16.10.

Nominal Size Range

2"-6”

Valve Type Valve Coding

Globe JHR-3CW
 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50

Valve Specification

Test and Inspection

Pressure Rating CL150
API 598

Design Code API 602

Body Material Carbon Steel Cast-ASTM A216 WCB

Trim Material Trim: 316L

Bolting Bolt to ASTM A193-B7M, Nut to ASTM A194-2HM

End Connection RF ASME B16.5

Temperature
-29~200°C
Limitations

Valve Operation

Body Construction Lift Piston

Trim
Lift with Spring,Piston
Type/Function

Notes: Packing Material:

1. Valves to be Asbestos Free.
Graphite/MFR’s Advice
2. Hydraulic Test According to API 598.
3.Valve Nameplate Shall be 316SS. Gasket Material:
Graphite/MFR’s Advice
4.All Material Shall Meet The Requirements OF NACE MR
0175/ISO15156.
5.Face to face dimensions to ASME B16.10.

Nominal Size Range

1/2”-1 1/2”

Valve Type Valve Coding

Check CR-1CW
 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50

Valve Specification

Test and Inspection

Pressure Rating CL150
API 598

Design Code API 594

Body Material Carbon Steel Cast-ASTM A216 WCB

Trim Material Trim: 316L

Bolting Bolt to ASTM A193-B7M, Nut to ASTM A194-2HM

End Connection RF ASME B16.5

Temperature
-29~200°C
Limitations

Valve Operation

Body Construction Wafer Type

Trim
Dual Plate
Type/Function

Notes: Packing Material:

1. Valves to be Asbestos Free.
Graphite/MFR’s Advice
2. Hydraulic Test According to API 598.
3.Valve Nameplate Shall be 316SS. Gasket Material:
Graphite/MFR’s Advice
4.All Material Shall Meet The Requirements OF NACE MR
0175/ISO15156.

Nominal Size Range

2”-2”

Valve Type Valve Coding

Wafer Check, D-PL CR-1CW
 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50

Valve Specification

Test and Inspection

Pressure Rating CL300
API 598

Design Code API 594

Body Material Carbon Steel Cast-ASTM A216 WCB

Trim Material Trim: 316L

Bolting Bolt to ASTM A193-B7M, Nut to ASTM A194-2HM

End Connection RF ASME B16.5

Temperature
-29~200°C
Limitations

Valve Operation

Body Construction Wafer Type

Trim
Dual Plate
Type/Function

Notes: Packing Material:

1. Valves to be Asbestos Free.
Graphite/MFR’s Advice
2. Hydraulic Test According to API 598.
3.Valve Nameplate Shall be 316SS. Gasket Material:
Graphite/MFR’s Advice
4.All Material Shall Meet The Requirements OF NACE MR
0175/ISO15156.

Nominal Size Range

2”-4”

Valve Type Valve Coding

Wafer Check, D-PL CR-3CW
 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50

Valve Specification

Test and Inspection

Pressure Rating CL300
API 598

Design Code API 608

Body Material Carbon Steel Forged-ASTM A105N

Trim Material Ball: 316L, Stem: 316, Seat and Seal: RPTFE

Bolting Bolt to ASTM A193-B7M, Nut to ASTM A194-2HM

End Connection RF ASME B16.5

Temperature
-29~200°C
Limitations

Valve Operation Lever

Body Construction Full Bore, Floating

Trim Anti-Static device & Fire-Resistance StructureAPI 607&Anti-Blow off

Type/Function Structure

Notes:
Packing Material:
1.Valves to be Asbestos Free.
Graphite/MFR’s Advice
2.Face to face dimensions to ASME B16.10.
3.Hydraulic Test According to API 598.
4. Valves Shall Have Position Indicator Showing Open
and Close Positions.
Gasket Material:
5.Valve Nameplate Shall be 316SS.
Graphite/MFR’s Advice
6. With A Lockable Device.
7.All Material Shall Meet The Requirements OF NACE MR
0175/ISO15156.

Nominal Size Range

1/2"-2”

Valve Type Valve Coding

Ball BHR-3CFW
 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50

Valve Specification

Test and Inspection

Pressure Rating CL300
API 598

Design Code API 6D

Body Material Carbon Steel Cast-ASTM A216-WCB

Trim Material Ball: 316L, Stem: 316, Seat and Seal: RPTFE

Bolting Bolt to ASTM A193-B7M, Nut to ASTM A194-2HM

End Connection RF ASME B16.5

Temperature
-29~200°C
Limitations

Valve Operation Lever

Body Construction Reduced Bore,Trunnion

Trim Anti-Static device & Fire-Resistance StructureAPI 607&Anti-Blow off

Type/Function Structure

Notes:
Packing Material:
1.Valves to be Asbestos Free. Graphite/MFR’s Advice
2.Face to face dimensions to ASME B16.10.
3. Hydraulic Test According to API 598.
4.Valves Shall Have Position Indicator Showing Open
and Close Positions.
Gasket Material:
5.Valve Nameplate Shall be 316SS.
Graphite/MFR’s Advice
6.With A Lockable Device.
7.All Material Shall Meet The Requirements OF NACE MR
0175/ISO15156.

Nominal Size Range

3”-6”

Valve Type Valve Coding

Ball BHR-3CRW
 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50

Valve Specification

Test and Inspection

Pressure Rating CL600
API 598

Design Code API 6D

Body Material Carbon Steel Forged-ASTM A105N

Trim Material Ball: 316L, Stem: 316, Seat and Seal: PEEK

Bolting Bolt to ASTM A193-B7M, Nut to ASTM A194-2HM

End Connection RF ASME B16.5

Temperature
-29~200°C
Limitations

Valve Operation Lever

Body Construction Full Bore, Floating

Trim Anti-Static device & Fire-Resistance StructureAPI 607&Anti-Blow off

Type/Function Structure

Notes: Packing Material:

Graphite/MFR’s Advice
1.Valves to be Asbestos Free.
2.Face to face dimensions to ASME B16.10.
3. Hydraulic Test According to API 598.
4.Valves Shall Have Position Indicator Showing Open
and Close Positions. Gasket Material:
5.Valve Nameplate Shall be 316SS. Graphite/MFR’s Advice

6.With A Lockable Device.

7.All Material Shall Meet The Requirements OF NACE MR
0175/ISO15156.

Nominal Size Range

1/2"-2”

Valve Type Valve Coding

Ball BHR-6CFW
 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50

Valve Specification

Test and Inspection

Pressure Rating CL2500
API 598

Design Code API 608

Body Material Stainless Steel Forged-ASTM A182 F304

Trim Material Ball: 304, Stem: F51, Seat and Seal: PEEK

Bolting Bolt to ASTM A320-B8M CL.2, Nut to ASTM A194-8M

End Connection RJ ASME B16.5

Temperature
-29~200°C
Limitations

Valve Operation Lever

Body Construction Full Bore, Floating

Trim Anti-Static device & Fire-Resistance StructureAPI 607&Anti-Blow off

Type/Function Structure

Notes:
Packing Material:
1.Valves to be Asbestos Free.
Graphite/MFR’s Advice
2.Face to face dimensions to ASME B16.10.
3. Hydraulic Test According to API 598.
4.Valves Shall Have Position Indicator Showing Open
and Close Positions.
Gasket Material:
5.Valve Nameplate Shall be 316SS.
Graphite/MFR’s Advice
6.With A Lockable Device.
7.All Material Shall Meet The Requirements OF NACE MR
0175/ISO15156.

Nominal Size Range

1/2”-1 1/2”

Valve Type Valve Coding

Ball BHJ-25PF
 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50

Valve Specification

Test and Inspection

Pressure Rating CL2500
API 598

Design Code API 6D

Body Material Stainless Steel Forged-ASTM A182 F304

Trim Material Ball: 304, Stem: F51, Seat and Seal: PEEK

Bolting Bolt to ASTM A320-B8M CL.2, Nut to ASTM A194-8M

End Connection RJ ASME B16.5

Temperature
-29~200°C
Limitations

Valve Operation Lever

Body Construction Full Bore, Trunnion

Trim Anti-Static device & Fire-Resistance StructureAPI 607&Anti-Blow off

Type/Function Structure

Notes: Packing Material:

Graphite/MFR’s Advice
1.Valves to be Asbestos Free.
2.Face to face dimensions to ASME B16.10.
3. Hydraulic Test According to API 598.
4.Valves Shall Have Position Indicator Showing Open
and Close Positions. Gasket Material:
5.Valve Nameplate Shall be 316SS. Graphite/MFR’s Advice

6.With A Lockable Device.

7.All Material Shall Meet The Requirements OF NACE MR
0175/ISO15156.

Nominal Size Range

2”-3”

Valve Type Valve Coding

Ball BHJ-25PF
 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50

Valve Specification

Test and Inspection

Pressure Rating CL2500
API 598

Design Code API 602

Stainless Steel
Body Material
Forged-ASTM A182 F304

Trim Material Trim: 304,Stem: F6a

Bolting Bolt to ASTM A320-B8M CL.2, Nut to ASTM A194-8M

End Connection RJ ASME B16.5

Temperature
-29~200°C
Limitations

Valve Operation Handwheel

Body Construction Bolted Bonnet, Rising Stem Outside Screw and Yoke

Trim Type/Function Plug

Notes: Packing Material:

1. Valves to be Asbestos Free. Graphite/MFR’s Advice
2.Face to face dimensions to ASME B16.10.
3. Hydraulic Test According to API 598.
Gasket Material:
4. Valve Nameplate Shall be 316SS.
Graphite/MFR’s Advice
5. Valve to be provided sand prevention component

Nominal Size Range

2"-2”

Valve Type Valve Coding

Globe JHJ-25P
 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50

Valve Specification

Test and Inspection

Pressure Rating CL2500
API 598

Design Code ASME B16.34

Body Material Stainless Steel Forged-ASTM A182 F304

Trim Material Ball: 304, Stem: F51, Seat and Seal: PEEK

Bolting Bolt to ASTM A320-B8M CL.2, Nut to ASTM A194-8M

End Connection RJ ASME B16.5

Temperature
-29~200°C
Limitations

Valve Operation Lever

Body Construction Full Bore, Floating

Trim Anti-Static device & Fire-Resistance StructureAPI 607&Anti-Blow off

Type/Function Structure

Notes:
Packing Material:
1. Valves to be Asbestos Free. Graphite/MFR’s Advice
2. Hydraulic Test According to API 598.
3.Valves Shall Have Position Indicator Showing Open
and Close Positions.
4. Valve Nameplate Shall be 316SS.
Gasket Material:
5.Double ball and bleed.
Graphite/MFR’s Advice
6.All Material Shall Meet The Requirements OF NACE MR
0175/ISO15156.
7.Bleed size is recommended by vendor.

Nominal Size Range

1/2”-1 1/2”

Valve Type Valve Coding

DBB Ball BHJ-25PD
 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50

Valve Specification

Test and Inspection

Pressure Rating CL2500
API 598

Design Code ASME B16.34

Body Material Stainless Steel Forged-ASTM A182 F304

Trim Material Ball: 304, Stem: F51, Seat and Seal: PEEK

Bolting Bolt to ASTM A320-B8M CL.2, Nut to ASTM A194-8M

End Connection RJ ASME B16.5

Temperature
-29~200°C
Limitations

Valve Operation Lever

Body Construction Full Bore, Trunnion

Trim Anti-Static device & Fire-Resistance StructureAPI 607&Anti-Blow off

Type/Function Structure

Notes:
Packing Material:
1. Valves to be Asbestos Free. Graphite/MFR’s Advice
2. Hydraulic Test According to API 598.
3.Valves Shall Have Position Indicator Showing Open
and Close Positions.
4. Valve Nameplate Shall be 316SS.
Gasket Material:
5.Double ball and bleed.
Graphite/MFR’s Advice
6.All Material Shall Meet The Requirements OF NACE MR
0175/ISO15156.
7.Bleed size is recommended by vendor.

Nominal Size Range

2”-3”

Valve Type Valve Coding

DBB Ball BHJ-25PD
 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50

Valve Specification

Test and Inspection

Pressure Rating CL150
API 598

Design Code API 608

Body Material Stainless Steel Forged-ASTM A182 F316/316L

Trim Material Ball: 316/316L, Stem: 316/316L, Seat and Seal: RPTFE

Bolting Bolt to ASTM A320-B8M CL.2, Nut to ASTM A194-8M

End Connection RF ASME B16.5

Temperature
-29~200°C
Limitations

Valve Operation Lever

Body Construction Full Bore, Floating

Trim Anti-Static device & Fire-Resistance StructureAPI 607&Anti-Blow off

Type/Function Structure

Notes:
Packing Material:
1.Valves to be Asbestos Free.
Graphite/MFR’s Advice
2.Face to face dimensions to ASME B16.10.
3.Hydraulic Test According to API 598.
4. Valves Shall Have Position Indicator Showing Open
and Close Positions.
Gasket Material:
5.Valve Nameplate Shall be 316SS.
Graphite/MFR’s Advice
6. With A Lockable Device.
7.All Material Shall Meet The Requirements OF NACE MR
0175/ISO15156.

Nominal Size Range

1/2"-2”

Valve Type Valve Coding

Ball BHR-1XF
 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50

Valve Specification

Test and Inspection

Pressure Rating CL150
API 598

Design Code API 602

Body Material Carbon Steel Cast-ASTM A182 F316/316L

Trim Material Trim: 316/316L

Bolting Bolt to ASTM A320-B8M CL.2, Nut to ASTM A194-8M

End Connection RF ASME B16.5

Temperature
-29~200°C
Limitations

Valve Operation

Body Construction Lift Piston

Trim
Lift with Spring, Piston
Type/Function

Notes: Packing Material:

1. Valves to be Asbestos Free.
Graphite/MFR’s Advice
2. Hydraulic Test According to API 598.
3.Valve Nameplate Shall be 316SS. Gasket Material:
Graphite/MFR’s Advice
4.All Material Shall Meet The Requirements OF NACE MR
0175/ISO15156.
5.Face to face dimensions to ASME B16.10.

Nominal Size Range

1/2”-1 1/2”

Valve Type Valve Coding

Check CR-1X
 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50

Valve Specification

Test and Inspection

Pressure Rating CL600
API 598

Design Code ASME B16.34

Body Material Stainless Steel Forged-ASTM A182 F316/316L

Trim Material Ball: 316/316L, Stem: 316/316L, Seat and Seal: PEEK

Bolting Bolt to ASTM A320-B8M CL.2, Nut to ASTM A194-8M

End Connection RF ASME B16.5

Temperature
-29~200°C
Limitations

Valve Operation Lever

Body Construction Full Bore, Trunnion

Trim Anti-Static device & Fire-Resistance StructureAPI 607&Anti-Blow off

Type/Function Structure

Notes:
Packing Material:
1. Valves to be Asbestos Free. Graphite/MFR’s Advice
2. Hydraulic Test According to API 598.
3.Valves Shall Have Position Indicator Showing Open
and Close Positions.
4. Valve Nameplate Shall be 316SS.
Gasket Material:
5.Double ball and bleed.
Graphite/MFR’s Advice
6.All Material Shall Meet The Requirements OF NACE MR
0175/ISO15156.
7.Bleed size is recommended by vendor.

Nominal Size Range

4”-4”

Valve Type Valve Coding

DBB Ball BHR-6XFD
 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50

Valve Specification

Test and Inspection

Pressure Rating CL600
API 598

Design Code ASME B16.34

Body Material Carbon Steel Cast-ASTM A216-WCB

Trim Material Ball: 316L, Stem: 316, Seat and Seal: PEEK

Bolting Bolt to ASTM A193-B7M, Nut to ASTM A194-2HM

End Connection RF ASME B16.5

Temperature
-29~200°C
Limitations

Valve Operation Lever

Body Construction Full Bore, Trunnion

Trim Anti-Static device & Fire-Resistance StructureAPI 607&Anti-Blow off

Type/Function Structure

Notes:
Packing Material:
1. Valves to be Asbestos Free. Graphite/MFR’s Advice
2. Hydraulic Test According to API 598.
3.Valves Shall Have Position Indicator Showing Open
and Close Positions.
4. Valve Nameplate Shall be 316SS.
Gasket Material:
5.Double ball and bleed.
Graphite/MFR’s Advice
6.All Material Shall Meet The Requirements OF NACE MR
0175/ISO15156.
7.Bleed size is recommended by vendor.

Nominal Size Range

4”-4”

Valve Type Valve Coding

DBB Ball BHR-6CFD
 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50

Valve Specification

Test and Inspection

Pressure Rating CL150
API 598

Design Code API 608

Body Material Stainless Steel Forged-ASTM A182 F316/316L

Trim Material Ball: 316L, Stem: 316L, Seat and Seal: RPTFE

Bolting Bolt to ASTM A320-B8M CL.2, Nut to ASTM A194-8M

End Connection RF ASME B16.5

Temperature
-29~200°C
Limitations

Valve Operation Lever

Body Construction Full Bore, Floating

Trim Anti-Static device & Fire-Resistance StructureAPI 607&Anti-Blow off

Type/Function Structure

Notes:
Packing Material:
1.Valves to be Asbestos Free.
Graphite/MFR’s Advice
2.Face to face dimensions to ASME B16.10.
3.Hydraulic Test According to API 598.
4. Valves Shall Have Position Indicator Showing Open
and Close Positions.
Gasket Material:
5.Valve Nameplate Shall be 316SS.
Graphite/MFR’s Advice
6. With A Lockable Device.
7.All Material Shall Meet The Requirements OF NACE MR
0175/ISO15156.

Nominal Size Range

1/2"-2”

Valve Type Valve Coding

Ball BHR-1XF
 PRODUCED GAS RECYCLING
FACILITY- SCOPE 3
Rev.:0
Project No.: CW2368055
Total Page:50

Valve Specification

Test and Inspection

Pressure Rating CL1500
API 598

Design Code API 608

Body Material Stainless Steel Forged-ASTM A182 F304

Trim Material Ball: 304, Stem: F51, Seat and Seal: PEEK

Bolting Bolt to ASTM A320-B8M CL.2, Nut to ASTM A194-8M

End Connection RJ ASME B16.5

Temperature
-29~200°C
Limitations

Valve Operation Lever

Body Construction Full Bore, Floating

Trim Anti-Static device & Fire-Resistance StructureAPI 607&Anti-Blow off

Type/Function Structure

Notes:
Packing Material:
1.Valves to be Asbestos Free. Graphite/MFR’s Advice
2.Face to face dimensions to ASME B16.10.
3. Hydraulic Test According to API 598.
4.Valves Shall Have Position Indicator Showing Open
and Close Positions.
Gasket Material:
5.Valve Nameplate Shall be 316SS.
Graphite/MFR’s Advice
6.With A Lockable Device.
7.All Material Shall Meet The Requirements OF NACE MR
0175/ISO15156.

Nominal Size Range

1/2”-2”

Valve Type Valve Coding

Ball BHJ-15PF