WTS700

Wireless Touchscreen

Quick User Guide

General Information
The WTS700 is a wireless Touchscreen that allows you to perform system arming and disarming functions, as well as to monitor the status of your security
system.
Navigating Menus
System Status is displayed at the top of each screen and the time and date are displayed at the bottom of the Security Screen. The Security Screen displays the
system status and selection “icons”. The displayed pages and options may vary slightly depending upon the devices and services that are installed in or
connected to the system.

Ready To Arm

System Tools
Ready To Arm

Arm Away Arm Stay Arm Custom Zones Scenes

9:11 AM Jauary 20, 2018

Home Screen

Function Icons
Arm the System
1 Select arming mode.
Selection Icon Function
Used to Arm the system in Away mode Arm Away (when you’re out) OR
Arm Away (displayed on both Home Screen pages).
Arm Stay (when you’ll be home) OR
Used to Arm the system in Stay mode Arm Custom (bypass selected zones)
Arm Stay (displayed on both Home Screen pages).

Used to Arm the system in Custom mode

Arm Custom 2 Enter user code.
(displayed on both Home Screen pages). 1 2 3
• System arms in selected mode
4 5 6
• Exit Delay countdown begins
Provides information about system status.
System 7 8 9 • Keypad beeps begin, if enabled
Clear
0 (Silent Exit mutes countdown beeps)
Provides access to Video cameras.
Video
Disarm the System
Provides access to Home Automation 1 Press Disarm icon.
Automation features.

Provides access to Zone information and Disarm

Zones options. 2 Enter user code.
1 2 3
• System disarms
Provides access to User Programming 4 5 6
• Entry Delay beeps stop (if beeps enabled)
Tools Menus (Master User Code required for 7 8 9
access). Clear
0
Provides access to Voice Command feature.
Voice
(Refer to the full User Guide for information
Command
regarding this feature.) Configure Wi-Fi
Provides access to Wi-Fi Configuration Connect the control to your local network router.
WiFi Config feature. (Refer to the full User Guide for 1 Select the WiFi Config Icon.
additional information regarding this feature.)
Used to advance to next screen OR return to
Next/Back WiFi Config
previous screen
2 Select from the following options:
Provides access to Panic functions.
Panic Scan for Network (to automatically display aviailble networks)
Manually Connect to the Network (Manually connect to a WiFi
Provides access to Home screen. network)
Home WPS (connect to a network via Wi-Fi Protected Setup)
Note : This option requires a WPS capable router.

Panic Icons 3a a. Select the desired network.

Scan for Network b. Enter the required information.
Selection Icon Function c. Select OK
Alerts the monitoring company that a fire 3b a. Enter the required information.
Manually Connect
Fire condition exists. Temporal (pulsing) sound. to the Network
(Displays zone 995) b. Select OK
Alerts the monitoring company that a police 3c WPS Follow the prompts.
Police emergency exists.
(Displays zone 999, default is silent)
If programmed, alerts the monitoring Panic Alarms
company to other types of emergency. See your installer for types of Panic alarms programmed for your system.
Personal
Steady alarm sound at keypad(s). Select the Panic Icon.
(Displays zone 996) Panic Then select the desired panic icon to activate that panic
alarm.
Assign User Codes Voice Command
Voice Command offers control of Z-Wave devices and Video functions by speaking in plain
1 Select the Tools Icon.
language. User-selected trigger phrases spoken near the Controller alert the system to
listen for further instructions. Refer to the system’s User Guide for additional information
Tools regarding this feature.
2 Enter Master User code.
1 2 3

4 5 6
View Cameras (if installed)
7 8 9

Clear
0 1 Select the Video Icon.

3 Select Users icon.

Video
2 Scan for cameras.
Users

4 Master To assign a Master, Guest, or Duress code, press
3 Select up top 4 cameras.
Guest the desired option then press Edit.
Duress To assign a regular user code, press Add New.
Add New
5 Name Select Name to assign a personal name to this 4 Display Select Display to view video from selected
Z-Wave Lock user. Follow the prompts. cameras.
User Code If desired, select Z-Wave Lock Control to set
whether entering this code at the Z-Wave door lock 5 Use zoom in, zoom out, and pan & tilt controls.
will disarm the system. Follow the prompts.
Select User Code to assign a 4-digit code to this Scan
6 Select Scan to list newly-installed cameras
user.
6 Assign 4-digit code and select Save.
1 2 3

4 5 6

7 8 9
Test the System
Clear
0 Disarm the system and close all protected windows and doors.
NOTE: Alarm messages are NOT sent to your alarm monitoring company during these tests.
1 Select the Tools Icon.

Bypass Zones
Tools
1 Press Zones icon. 2 1 2 3 Enter the Master user code
4 5 6

7 8 9
2 Select zones to bypass from list. Clear
0

3 Select Advanced icon, then select Walk Test

3 BYPASS Select BYPASS.
Advanced
4 Enter user code.
4 Trigger Zones Trigger (open and close) all zones.
5 Bypassed zones appear in list with icon. Listen for three beeps from the controller when each
zone is triggered
- 5 Exit Test mode When testing is completed, press the Home button on
6 1 2 3 Arm the system as usual. the controller and enter the Master User Code if
prompted.
4 5 6

7 8 9

Clear
0

Settings
1 Select the Settings Icon.
Activate Automation Devices (Z-Wave)
Z-Wave device (for Lights, Locks, Thermostats and Garage Doors), inclusion
and exclusion is via the ADC and/or ADT Pulse app. Refer to the systems Settings
User Guide for additional information. Brightness
2 + Adjust screen brightness and Voice/Chime volume.
1 Select the Scenes Icon. Volume
+

Brightness
Scenes Volume
2 Select type of device.
3 Select VOICE or CHIME to mute voice announcements
Brightness

Volume
+ and/or chime sounds if desired (highlighted [blue] button
+
VOICE
indicates active).
CHIMES

Clean

3 Select a specific device from the list.

VOICE / CHIME
4 Select Clean icon before cleaning the screen; use a
damp, soft cloth while screen is disabled for 15
seconds.
4 Select Desired Action Select the desired action for that device.
Actions vary based on the device selected. Clean

FOR MORE DETAILED INFORMATION

These instructions provide a brief overview of common system functions. For full details of all user functions, please see the system’s User Guide located online at:
https://www.adt.com/help/faq/system-user-guides (see ADT7AIO User Guide P/N 800-24122 or higher).
Refer to Installation Instructions PN 800-24298 for more detailed information.

Warning – 5G Band 5150-5250MHz is only for indoor use.

ADT Securit y Servi ces Ê800-243262Š

1501 Yamato Road (BETA) 800-24326 4/18 Rev A Part 1
Boca Raton, FL 33431
© 2018 ADT Securit y Services