Vane Pump Type V3

Hal Automation Ltda

Size 12 - 63 Up to 10Mpa Up to 63 L/min

Features:

- Low noise level.

- Long service life.
- Easy commissioning due to automatic bleed facility.
- Lubricated bearings for long bearing life.
- Good sliding characteristics of control discs due to bronze coating and semi-fluid friction.

Functional, section, symbol

Hydraulic pumps type V3 are vane pumps with variable displacement and pressure
control, can be installed in any desired position. The pump may be connected to systems
only by means of flexible lines hydraulics. The pump may be connected to motor only by
means of a flexible coupling. All the coaxial conditions formulated by the coupling
manufacturer must be maintained. Pumps type V3 are composed of a housing, rotor with
simple vanes, stator, pressure regulator, volume screw, valve for automatic air bleed and
control discs. They decrease their volume and thus fluid is pushed to the pressure channel P
and into the system.
 Suction and delivery

The pumps are delivered in the assemble state, primed. The pump top coat can be
carried out in agreement with the producer. The spare parts, fastening bolts and
connections are not parts of delivery. Instruction manual is delivered with each pump.
Production materials used are cast iron, steel and non-ferrous metals.

PRESSURE REGULATION

The circular stator ring is kept in an eccentric position by means of the spring 10.
Maximum working pressure required in the system is adjusted by the spring 10. On
reaching the set pressure the stator 4 (overcoming resistance of the spring 10) moves out
of its eccentric position. The eccentricity decreases till the minimum flow replacing the
leakage oil is obtained. After a pressure drop in the system the stator 4 returns to the
eccentric position and the pump delivers the full value of the set output flow.

OIL TANK AND FILTRATION

The tank capacity must be properly selected so that the working temperatures of oil
do not exceed recommendations. If that is impossible a cooler must be installed. The
contents of the tank must accomplish the drive requirements, so that the working
temperature must not exceed recommended level. If necessary a cooler must be fitted.
Usage of a pressure oil filter or a filter in return channel T is recommended. If a suction
filter is used then an under pressure switch must be fitted.

ATTENTION!

In case that difference of temperature of the hydraulic oil is more than 20°C during a
start the pump, it is recommended to start the pump by short pulses (switch on approx. 1
sec. and switch off approx. 5 sec.) to prevent of seizure. In the case that hydraulic oil is
heated by meaning of heater it is necessary to switch on the pump in the same time.
 HD 1 PV V3
01 02 03 04 05 06 07 08 09 10 11 12 13 14

01 HD - Technology of Beijing Huade Hydraulic

02 1PV - One-flow pump with variable geometrical displacement

Mounting Method
03 2 – Flange (Standard)
6 - Subplate

Pump
04 V3 - Vane pump type V3

Series Number
05 30 - Series 30; nominal size 40 - 63
40 - Series 40; nominal size 12 - 25

Nominal Size
12 - Nominal size 12 – 8.5 cm3 /rev
06 25 - Nominal size 25 – 19 cm3 /rev
30 - Nominal size 40 – 32 cm3/rev
40 - Nominal size 63 – 47 cm3 /rev

Rotation Direction
R – Right (Standard)
07 L - Left
D – Model with double shaft

Connections Method
08 1 - Threaded connections (Standard)
8 - Subplate
Sealing
09 M - For fluids on mineral oil base (Standard)
V - For fluids on phosphate ester base
Pressure Setting
C - With hexagon end screw (Standard)
10 H - With square end screw
S – Lockable pressure regulator

Zero stroke pressure range

100 – 100 bar zero stroke pressure
63 - 63 bar zero stroke pressure
11 40 - 40 bar zero stroke pressure
25 - 25 bar zero stroke pressure

Flow setting
A - With hexagon end screw (Standard)
12 H - With square end screw
S – Lockable pressure regulator
13 Air bleed valve

14 Additional requirements in clear text (to be agreed with the manufacturer)

 Technical Data Symbol Units Nominal Sizes
V3/12 V3/25 V3/40 V3/63
Nominal displacement Vg cm³/rev 8.5 19 32 47
Nominal output flow at n = 1450 rpm Qn L/min 13 27.5 47 67
Speed range n Min-¹ 950 up to 1800
Spring type C25, C40, C63, C100
Pressure range p bar 12 … 25 20 … 40 30 … 63 50 … 100
Operating pressure: Input P bar 0.2 (underpressure) up to 5 (overpressure)
Output p bar max. 100 – continuous op. pressure
Leakage port p bar Max.2
Hydraulic medium Mineral oils HLP DIN 51 524 part 2
Temperature range °C -10 up to +70
Fluid filtration 25 absolute (ß20 ≥ 100) We recommend 10 µm
in order to achieve long working life, with heavy
loading, high duty and low viscosity
Oil viscosity range ν
- at pzero stroke < 6.3 MPa mm² /s 16 to 160
- at pzero stroke > 6.3 MPa mm² /s 25 to 160
Efficiency see curves

Weight m kg 6.25 11.1 26.5 29.5

Pipe connections threaded connections

Shaft loading radial or axial loads can’t be transferred

Rotation direction right (or left for 1 PV6 only)

INSTALLATION DIMENSIONS V3/12
 PERFORMANCE CURVES V3/12

EFFICIENCY CURVE V3/12 - (n = 1500 rpm, t = 50°C)

INSTALLATION DIMENSIONS V3/25
 PERFORMANCE CURVES V3/25

EFFICIENCY CURVE V3/25 - (n = 1500 rpm, t = 50°C)

INSTALLATION DIMENSIONS V3/40
 PERFORMANCE CURVES V3/40

EFFICIENCY CURVE V3/25 - (n = 1500 rpm, t = 50°C)

INSTALLATION DIMENSIONS V3/63
 PERFORMANCE CURVES V3/63

EFFICIENCY CURVE V3/25 - (n = 1500 rpm, t = 50°C)

 DATA FOR ORDERING MULTIPLE PUMPS – REAR PUMP

The pump combination V3 + V3 is

composed of two variable displacement
vane pumps. The front pump is flange or
subplate mounted for systems hydraulics.
Variable flow displacement is gained by
means of the pressure compensator.
Because of this, loss of power in the circuit
is kept to a minimum. For further details
on the individual pumps see the data cards of pumps V3. Both pumps are works from one
common shaft. Their delivery flow varies from Qmin (zero) to Qmax as required by the user.
 HD 1 PV 2 V3 R G 1
01 02 03 04 05 06 07 08 09 10 11 12 13 14

01 HD - Technology of Beijing Huade Hydraulic

02 1PV - One-flow pump with variable geometrical displacement

Mounting Method
03 2 – Flange (Standard)
6 - Subplate

Series Number
05 for V3/12 i 25 (30 − 39) Connection and installation dimensions remain
for V3/40 i 63 (20 − 29) unchanged

Nominal Size
WN12 + WN12 WN40 + WN40
WN25 + WN12 WN63 + WN12
06 WN25 + WN25 WN63 + WN25
WN40 + WN12 WN63 + WN40
WN40 + WN25 WN63 + WN63

Connection
1 – Threads
9 8 - Subplate

Sealing
M - For fluids on mineral oil base (Standard)
10 V - For fluids on phosphate ester base

Pressure Setting
C - With hexagon end screw (Standard)
11 H - With square end screw
S – Lockable pressure regulator

Zero stroke pressure range

100 – 100 bar zero stroke pressure
63 - 63 bar zero stroke pressure
12 40 - 40 bar zero stroke pressure
25 - 25 bar zero stroke pressure

Flow setting
A - With hexagon end screw (Standard)
13 H - With square end screw
S – Lockable pressure regulator

14 Air bleed valve

Overall dimensions for pump combination V3/12 + V3/12

Overall dimensions for pump combination V3/25 + V3/12

Overall dimensions for pump combination V3/25 + V3/25

Overall dimensions for pump combination V3/40 + V3/12

Overall dimensions for pump combination V3/40 + V3/25

Overall dimensions for pump combination V3/40 + V3/40

Overall dimensions for pump combination V3/63+ V3/12

Overall dimensions for pump combination V3/63 + V3/25

Overall dimensions for pump combination V3/63 + V3/40

Overall dimensions for pump combination V3/63 + V3/63

ANNOTATIONS :

HUADE AMÉRICA
CEP : 03162-020
RUA HIPÓDROMO 1445 – MOOCA, SÃO PAULO, SP, BRASIL
TEL : (11) 3186-5959
[email protected]
www.huade.com.br

Huade América