Dell EMC Simple Support Matrix

Dell EMC RecoverPoint 4.1.x

DECEMBER 2016
REV 16

© 2014 - 2016 EMC Corporation. All Rights Reserved.

EMC believes the information in this publication is accurate as of its publication date. The information is subject to change without
notice.

THE INFORMATION IN THIS PUBLICATION IS PROVIDED “AS IS.” EMC CORPORATION MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WITH RESPECT TO THE INFORMATION IN THIS PUBLICATION, AND SPECIFICALLY
DISCLAIMS IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Use, copying, and distribution of any EMC software described in this publication requires an applicable software license.

EMC2, EMC, and the EMC logo are registered trademarks or trademarks of EMC Corporation in the United State and other countries.
All other trademarks used herein are the property of their respective owners.

For the most up-to-date regulatory document for your product line, go to EMC Online Support (https://support.emc.com).
Table 1 through Table 6 provide interoperability and system limits information for EMC® RecoverPoint ® 4.1.x with EMC
arrays.

Table 1 EMC RecoverPoint 4.1.x interoperability and system limits

EMC arrays a Supported Patch System limits

versions b
Array-specific limits General limits
VMAX 40K ®
EMC Symmetrix® 5876.229.145 Number of: Number of:
Enginuity™ version 5876.159.102 • RP clusters connected to splitter = 6 • RPAs per site = 8
VMAX 20K/VMAX 5876 5876.251.161 • GK devices = 8 per RPA • CGs (including disabled)
VMAX 10K (SN xxx987xxxx) 5876.268.174 Minimal number of: per RPA = 64; 128 in
5876.269.175 • GK devices = 2 per RPA disaster. All should be able
VMAX 10K (SN xxx959xxxx)/ 5876.272.177
VMAXe to transfer.
5876.286.194 • CGs (including disabled)
5876.288.195 per Cluster= 128
VMAXe Enginuity 5875 5875.267.201e • Distributed CGs = 8
• Replication sets = 8k
VPLEX® EMC GeoSynchrony® Number of:
• Maximum replication
5.2, 5.3, 5.4.1.x, • RP clusters connected to splitter = 6 limit = 2 petabytes
5.5.1.x, 5.5.2.x, and • Number of splitters per RPA cluster = 10 • Maximum size of
6.0.1 • Replication sets = 8K replicated volume = 32 TB
• DR1 Replication sets = 1.2K • Number of volumes per
cluster = 16k
XtremIO™e 4.0.0-64, 4.0.1-x, Number of:
• Volumes per CG = 64 • Number of paths per
4.0.2-x, 4.0.4-x, RP cluster= 200,000
4.0.10-x • Number of volumes + snapshots per array =
8K
• # of replicated volumes per array & Per RP
Cluster = 500
• RP clusters connected to splitter = 4
• Number of replicated arrays per cluster = 4
• Number of snapshots per CG on target = 500
Unified VNX® Series VNX-OE 33 c, d 015 and later Number of:
• RP clusters connected to splitter= 6
VNX-OE 32 d 011 and later
• Number of splitters per RPA cluster = 10
VNX-OE 31 008 and later
® Series Number of:
Unified VNXe VNXe 3200 OE v3.x 4993502 and
MR 1.1 f later • RP clusters connected to splitter= 1
• Number of splitters per RPA cluster = 10
CLARiiON® CX4 EMC FLARE® 30 526 and later Number of:
• Attached LUNs = 2048
• RP clusters = 4
Footnotes:
a. EMC RecoverPoint array-based splitters are supported with all operating systems that are supported by the corresponding arrays, as documented in the EMC Support Matrix,
as long as they are 512K block size.
b. When not using the latest version, please refer to any older versions of the EMC RecoverPoint ESSM posted on the E-Lab Navigator, https://elabnavigator.emc.com for
limitations.
c. VNX 5200/5400/5600/5800/7600/8000.
d. Snap Based Replication limitation: Support with VNX Flare 32 Patch 05.32.000.5.215 and later. Support with VNX Flare 33 Patch 015 and later.
e. XtremIO array is only supported with RecoverPoint 4.1 SP2 and later.
f. Customers upgrading to OE MR1 SP1 (3.1.5.6801782) or later must first upgrade to RecoverPoint 4.1.2 or later to avoid connectivity issues.
Note: ScaleIO-to-ScaleIO replication is only supported on fresh installs of RecoverPoint "rel4.1.SP1_s.71" and ScaleIO version 1.31.1/2.

Table 2 RecoverPoint 4.1.x hardware

Hardware supported Hardware not supported
GEN-6 GEN-1 or DELL2950 phase-2
GEN-5 GEN-3 or DELL2950
GEN-4 Legacy hardware
Footnotes:
2/24/16 a. The Gen 6 appliance is only supported from 4.1.3 and above.
 Table 3 RecoverPoint 4.1.x application interoperability
Application Version
CE - RP/CE Not supported
DM rel4.4.SP1.HF130502_h.148
KVSS Match the installed RP version

Table 4 RecoverPoint 4.1.x interoperability with VMware

,b
VMware version SRM SRA vSphere Supported splitters
e
ESX 4.0 All splitters supported by
5.1 2.1 5.1
RecoverPoint 4.1.x
ESX/ESXi 4.1 e All splitters supported by
5.1 2.1 5.1
RecoverPoint 4.1.x
ESXi 5.0 e All splitters supported by
5.1 2.1 5.1
RecoverPoint 4.1.x
ESXi 5.1 e 2.1 / 2.2 / 2.2.0.1 c / All splitters supported by
5.1 5.1
2.2.0.3 c RecoverPoint 4.1.x
ESXi 5.5 e 5.5 2.1 / 2.2 / 2.2.0.1 c / All splitters supported by
5.5
5.8 2.2.0.3 c RecoverPoint 4.1.x
ESXi 6.0 e 6.0 d All splitters supported by
2.2.0.3 6.0
6.1 d RecoverPoint 4.1.x
Footnotes:
a. For more information regarding SRM supported versions, refer to the VMware Product Interoperability Matrixes at
http://partnerweb.vmware.com/comp_guide2/sim/interop_matrix.php.
b. PPVE multipath is recommended when working with SRM on VPLEX storage.
c. When upgrading to SRA v2.2.0.1 and above, RPA security setting should be configured to https mode. See the EMC
RecoverPoint Storage Replication Adapter for VMware vCenter Site Recovery Manager Release Notes for more details at
https://support.emc.com.
d. SRM 6.0 is supported only with SRA 2.2.0.3 and above.
e. All released updates of VMware ESX/ESXi versions are supported unless specified by another footnote. Contact the server
vendor for the update level required for a specific server.

Table 5 Web browser support for VNX Unisphere

Web browser Unisphere 1.0 Unisphere 1.5
Google Chrome Supported Supported
Internet Explorer Supported Supported
Mozilla Firefox Supported Supported

Table 6 Web browser support for Unisphere for RecoverPoint

Web Browser Version Win Linux Mac
Internet explorer 7 and later Supported Supported —
Google Chrome 2.0 and later Supported — —
Mozilla Firefox 4.0 and later Supported Supported —
Safari on MAC 5.0 and later — — Supported
Notes:
Minimum Flash version for Unisphere for RecoverPoint GUI is 10 and later.

Table 7 vRPA configuration

CPU Memory iSCSI Adapter
Minimum 2 CPUs 4 GB 1G
Maximum 8 CPUs 8 GB 10 G
Notes:
• Supported on ESX 5.0 and above.
• Only supported on VNX Inyo MR1 SP1(iSCSI splitter support) and later.
2/24/16