Scribd
Upload
11 views

Component DTC Error Code Description: Injector

eicher

Uploaded by

rubelhoque2013
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
11 views

Component DTC Error Code Description: Injector

eicher

Uploaded by

rubelhoque2013
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Component DTC Error code description

Injector P0274-00 Injector 5 Short Circuit High.

Sensor location Sensor view

It is located on engine.

Error occurring
Effect on the vehicle Probable causes Remedial actions
condition
• Low power. • Connector. • Check whether the
Injector Activated. • Uneven operation. • Wiring harness. connecter is properly
• Abnormal noise. • Nozzle. connected to the 5th injector.
• Engine is operating on • Check for the continuity
only 5 cylinders. between 5th injector
connector pins and ECU
connector pins.
• Change the injector.
Connector view
ECU connector Sensor connector

Circuit diagram
Circuit description:

From pin no To pin no


Component Wiring color code Wiring function
(sensor) (ECU)J1
1 49 1.0 V Signal
Injector 1
2 50 1.0 R/B Signal

1 75 1.0 R Signal
Injector 2
2 51 1.0 Y Signal

1 73 1.0 O Signal
Injector 3
2 74 1.0 GR Signal

1 27 1.0 GR/G Signal


Injector 4
2 03 1.0 W/R Signal

1 25 1.0 G Signal
Injector 5
2 01 1.0 B Signal

1 26 1.0 L Signal
Injector 6
2 02 1.0 W Signal

Circuit Inspection

Type of Pre- From pin Interconnector To pin no Expected


Component
inspection condition no pin ECU J1 result
1 14 49
Injector 1
2 13 50
1 12 75
Injector 2
2 11 51
1 10 73
Injector 3
2 09 74 Beep from
Continuity Ignition Off
1 08 27 multimeter
Injector 4
2 05 03
1 04 25
Injector 5
2 03 01
1 02 26
Injector 6
2 01 02
Pre- From pin
Type of inspection To pin no Expected result
condition no
Voltage Ignition On 5 Ground 4.75 to 5.75
Resistance Ignition off 1 2 1.5 to 2.5 Ohms

General Inspection:

Visual inspection (Electrical):

1. Check that the connectors are properly connected and locked into position
2. Disconnect and check the component connector
3. Inspect pins and terminals for oxidations or corrosion
4. Ensure that the pins and terminals are locked into the connectors and that they are not pushed
back out of the sockets
5. Check the pins and terminal are not damaged (which can cause poor connection)

Visual inspection (Mechanical):

• Check injector solenoid operation using Injector cutoff test and Injector click test in Techtool

Inspection using Fault code status check:

A) If there is a Short circuit DTC in the ECU, to identify whether the fault is in wiring harness or the
sensor, disconnect the component connector, (creating open circuit) and re-read fault code
status to see if status changes (where applicable).

o If the fault code changes i.e. open circuit DTC occurs, issue is with the internal circuit of
the component
o If the fault code does not change, issue is with the wiring harness

B) Connect a new sensor with the ECU and check whether the fault gets erased
o If the fault code gets erased, issue is with the internal circuit of the component
o If the fault code does not change, issue is with the wiring harness

You might also like