Scribd
Upload
12 views

G11 Term 2

Uploaded by

msonindeuleted
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
12 views

G11 Term 2

Uploaded by

msonindeuleted
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 7

Name ………………………………………………………………..

11

MINISTRY OF EDUCATION
KAFUMBWE BOARDING SECONDARY SCHOOL
Examination for General Certificate of Education Ordinary Level
END OF TERM 2 EXAMINATION
Design and Technology 6045/1
Paper 1 (Theory & Design)
Grade 11 – 2024.
Additional Materials:
A3 Drawing paper
Drawing Instruments

Time: 2 hour 30 minutes Marks: 120


Instructions to candidates
1. Write your name, center number and candidate number, in the spaces at the top of this
page and on the separate Answer booklet provided by yourself.
2. If working is needed for any question, it must be shown in the spaces provided in the
question paper and answer booklet.
3. There are two sections in this paper. Section A and B. answer all questions.
4. Section B has three parts I, II and III. ANSWER ALL THE QUESTIONS
5. The question in part III should be answered on the A3 drawing paper you have provided
6. Where a freehand sketch is required, it must be drawn to half full size
k with good line work.
7. At the end of the examination fasten the answer booklet and drawing paper used securely
to the question paper,
Information for candidates
1. The number of marks is given in brackets [ ] at the end of each question or part of
question.
2. Use of color is allowed.
3. All dimensions are in millimeters
4. Cell phones and calculators are not allowed in the
examination room.
For Examiner’s use
Section A
Section B
@KSS/D&T/6045/1/2021/MWAMBA EF This question paper consists of 11 printed pages
Part I
Part II
Part III
Total

Page 1 of 7
Section A [30 marks]
Answer all the question in the spaces provided on this question paper.
If working is needed for any question, it must be shown in the space below that question.

1. (a)Figure 1 shows one of the holding tools used in the Design and Technology workshop.

i) Give the name of the tool in figure …………………………………………………………….


……………………………..……. [1]
ii) State one reason why it is necessary to place scrap wood underneath the work piece when drilling. .
……………….…..…………………………………………………….
………......................................................................................................................................................................
... [1]
iii) In what group does the tool mentioned in figure 1 belong to?
..…………………………………………………………………………………………………. [1]
(b) i) State the function of a mallet …………….
……………………………………………………………………………… [1]

ii. State any one suitable material used in making the head of a mallet.
…………………………………………………………………………………………………….... [1]
iii. One of the safety precautions to observe when working with a mallet is to use a correct mallet for the right
job. Suggest one other safety rule to observe.
…………………………………………………………………………………………… [1]

[Total: 6 marks]

Page 2 of 7
2. a) Figure 2 below shows a bicycle.

Fig. 2

I. If the direction of input is as shown, what will be the resultant motion on the wheels?
……………………………………………………………………………………… [1]
II. One type of mechanism is rack and pinion. Name one other type and give an example were

it is used

a) Mechanism: ………………………………………………………….. [1]

b) Use: ………………………………………………………………..………. [1]

b) Figure 3 shows an electric circuit diagram.

Identify the components labeled A, B and c

A ………………………………………………………………….. [1]

B ………………………………………………………………………… [1]

C ………………………………………………… [1]

Page 3 of 7
3. a) Figure. 4 shows views of a smart phone desk stand

Fig.4

i. Suggest the material from which the above stand can be realized.

…………………………………………………………………………………….… [1]

ii. State two reasons for your choice of materials

…………………………………………………………..……………………

………………………………………………………………….…… [2]

iii. draw and label a mallet [5]

4. (a)
The figure below shows an incomplete table of electronic symbols. (i)Complete the table by filling in the
blanks with right answers. [28marks]
S/N Symbol Name Function
i.

ii. Capacitor

iii. Path of electrical current from one part to another

iv. Supplies electrical energy

v. Transformer

vi.

vii. Restrict the flow of current

Page 4 of 7
[14]

5. There are many tools and equipment used in design and technology. The figure below shows one of
them.

i) Classify the tool …………………………………………………………………[1]


ii) Record any two uses of the tool.
a) ………………………………………………………………………………...[1]
b) ………………………………………………………………………………...[1]
iii) K what is the purpose of the hole? ……………………………………………………………………...[1]
iv) Why is it necessary to start measuring from zero 0? …………………………………………...[1]

Section B
1.With aid of drawing explain step by step how to prepare scotch glue.
i.List down three disadvantages of scotch glue

ii Hook and band

Use.........................................................................................................................................

Page 5 of 7
Section c
CHOOSE ONE QUESTION FROM THIS SECTION
1. Draw surface development of figure shown below

AC=40

2. Draw surface development of figure shown below

AC=50

BEST WISHES

Page 6 of 7
Page 7 of 7

You might also like