DataSheet

MT-X552
This document contains the specifications for MT-X552.Specifications are typical at 25°C
unless otherwise noted.

Caution Using the MT-X552 in a manner not described in this document

may impair the protection the MT-X552 provides.
Analog Input
Number of channels 16 single-end
ADC resolution 16 bits
Type of ADC Successive approximation register (SAR)
Input range ±10V
Input Voltage Ranges
Measurement Voltage (AI+ to AI-)
Minimum(V) ±10.2V
Typical(V) ±10.4V
Maximum ±10.6V
Overvoltage protection ±30 V
Conversion time 5 μs minimum
Sample rate 200 kS/s maximum per channel
Table 1. Accuracy
Percent of Reading Percent of Range
Measurement Conditions
(Gain Error) (Offset Error)

Maximum (-40 °C to 70 °C) 0.142% ±0.070%

Calibrated
Typical (23 °C ±5 °C) 0.010% ±0.007%
CMRR 120 dB minimum
-3 dB bandwidth >10 kHz
Input impedance >1 GΩ
Crosstalk -90 dB
Total Harmonic Distortion(THD) -107dB
No missing codes 16 bits
DNL ±0.5LSB
INL ±0.5LSB
SNR 90 dB
SFDR 109 dB
Analog Output
Number of channels 8
DAC resolution 16 bits
Type of DAC String
Output voltage range ±10V
Current drive ±10 mA per channel maximum
Output impedance 375 Ω
Sample rate 200KS/s maximum per channel
Table 2. Accuracy
Percent of Reading Percent of Range
Measurement Conditions
(Gain Error) (Offset Error)

Maximum (-40 °C to 70 °C) 0.214% 0.075%

Calibrated
Typical (25 °C, ±5 °C) 0.010% 0.007%
Gain drift ±0.1 ppm/°C
Zero-code drift ±0.05 ppm/°C
Protection
Overvoltage ±30V
Short-circuit Indefinitely
Noise
Output noise 10nV / √Hz
Slew rate 25V/us
Crosstalk 74dB
Capacitive drive 1nF
DNL ±1 LSB maximum
INL (endpoint) ±1 LSB maximum
Counter
Voltage Level 5V
Number of Channels 4
Counter measurements Edge counting,pulse,pulse width,frequency
Maximum input frequency 2MHz

PWM
Voltage Level 5V
Number of Channels 4
Maximum output frequency 500kHz

Encoder
Voltage Level 5V
Number of Channels 2 (each with A,B,Z)
Position measurements Quadrature encoding
Figure 1. Quadrature encoding

Digital Trigger
Voltage Level 5V
Number of Channels 2

Digital Waveform Input/Output

Voltage Level 5V
Number of Channel 2 Digital Waveform In, 2 Digital Waveform Out
Maximum update rate 5MHz

Digital Input/Output
Voltage Level 5V
Number of Channel 6 Digital Input,6 Digital Output
Maximum update rate 500Hz

External Digital Triggers

Number of triggers 12
Source Digital Triggers,TRIG,PXI_TRIG<0..7>,
PXI_STAR

Maximum Power Requirements

Power requirements are dependent on the digital output loads and configuration of the
LabVIEW FPGA VI used in your application.
+3.3V 1.23 A
+12 V 0.57 A

Physical Characteristics
Weight 200g
Dimensions See end of this document

Safety Voltages
This product is designed to meet the requirements of the following electrical equipment safety
standards for measurement, control, and laboratory use:
• IEC 61010-1, EN 61010-1
• UL 61010-1, CSA C22.2 No. 61010-1
CE Compliance
This product meets the essential requirements of applicable European Directives, as follows:
• 2014/35/EU; Low-Voltage Directive (safety)
• 2014/30/EU; Electromagnetic Compatibility Directive (EMC)
• 2014/34/EU; Potentially Explosive Atmospheres (ATEX)

Shock and Vibration

To meet these specifications, you must panel mount the system.
Operating vibration
Random (IEC 60068-2-64) 5 grms, 10 Hz to 500 Hz
Sinusoidal (IEC 60068-2-6) 5 g, 10 Hz to 500 Hz
Operating shock (IEC 60068-2-27) 30 g, 11 ms half sine; 50 g, 3 ms half sine;
18 shocks at 6 orientations

Environmental
Refer to the manual for the chassis you are using for more information about meeting these
specifications.
Operating temperature -40 °C to 70 °C
(IEC 60068-2-1, IEC 60068-2-2)

Storage temperature -40 °C to 85 °C

(IEC 60068-2-1, IEC 60068-2-2)
Ingress protection IP40
Operating humidity (IEC 60068-2-78) 10% RH to 90% RH, noncondensing Storage
humidity (IEC 60068-2-78) 5% RH to 95% RH, noncondensing Pollution
Degree 2
Maximum altitude 4,000 m
Indoor use only.
DAQMode Support
通用模式（DAQMode=0）包括：AI、AO、Counter、PWM、Encoder、Digital Input、Digital
Output、Digital Waveform Input、Digital Waveform Output、Temperature。
通用模式适用所有的MT-DAQ设备，该模式下用户可以开发使用设备数据手册中说明的全
部功能，不同设备支持的功能不同。本设备通用模式支持的功能如下表所示，对应功能为绿色
则支持，红色则不支持。
本设备通用模式（DAQMode=0）支持的功能：
AI AO
Counter PWM
Encoder Temperature
Digital Input Digital Output
Digital Waveform Input Digital Waveform Output
特殊模式包括：AI/AO同步（AIO Sync）、编码器触发AI（Encoder Trigger AI）、AI触发
编码器（AI Trigger Encoder）、DI触发AI/AO同步（DI Trigger AIO）、DI触发AI（DI Trigger AI）、
DI触发AO（DI Trigger AO）。
如果需要使用特殊模式下的模式，用户需要确认购买设备是否支持该模式，本设备支持的
特殊模式如下表所示，对应模式为绿色则支持，红色则不支持；Customer是定制DAQ模式，正

常用户无法使用。如果模式配置错误，会导致设备无法正常运行。
本设备支持的特殊模式：
AO-Sync-AI (DAQMode=1) AI-Trigger-Encoder (DAQMode=2)
Encoder-Trigger-AI (DAQMode=3) DI-Trigger-AI-Sync-AO (DAQMode=4)
DI-Trigger-AI (DAQMode=5) DI-Trigger-AO (DAQMode=6)
Config文本
MT-DAQ设备的开发和使用依赖于Config配置文本，只有正确配置该文本，才能保证设备
的正常运行。不同型号的设备或板卡对应的配置参数是不同的。Python、LabVIEW和C#三种
编程语言的Config配置文本完全相同。
通用Config配置文本通过MT-Master软件主页导出获得，用户可以根据实际设备或板卡的
参数对配置文本进行修改配置，或者按照文本默认参数配置运行。
Config配置文本中的各项参数含义及其具体配置可以参考MT-DAQ上手指南，指南链接附
于下文Support板块。
使用MT产品过程中如有任何疑问，可以通过访问官网：http://www.mangotree.cn联系专业
客服咨询。
Support
MT-Master上手指南：
https://server.mangotree.cn:9900/WebFile/Downloads/上手指南/MT-Master/

MT-Master视频教程：
https://server.mangotree.cn:9900/WebFile/Downloads/视频教程/MT-Master/

MT-DAQ上手指南：
https://server.mangotree.cn:9900/WebFile/Downloads/上手指南/MT-DAQ/

MT-DAQ视频教程：
https://server.mangotree.cn:9900/WebFile/Downloads/视频教程/MT-DAQ/
MT-X552 Pinout

CONNECTOR 0 CONNECTOR 1

AI 0 68 34 NC +5 V 1 35 +5 V
A GND 67 33 A GND D GND 2 36 Encoder1.A
AI 1 66 32 NC D GND 3 37 Encoder1.B
AI 2 65 31 NC D GND 4 38 Encoder1.Z
A GND 64 30 A GND D GND 5 39 PWM 2
AI 3 63 29 NC D GND 6 40 PWM 3
AI 4 62 28 NC D GND 7 41 Counter 2
A GND 61 27 A GND D GND 8 42 Counter 3
AI 5 60 26 NC D GND 9 43 Digital Input 3
AI 6 59 25 NC Digital Input 4 10 44 Digital Input 5
A GND 58 24 A GND Digital Output 3 11 45 Digital Output 4
AI 7 57 23 NC TERMINAL 68 TERMINAL 35 Digital Output 5 12 46 Digital Waveform In 1
A GND 56 22 A GND Digital Waveform Out 1 13 47 Digital Trigger 1
AI 8 55 21 AO 0 TERMINAL 34 TERMINAL 1 NC 14 48 NC
AI 9 54 20 AO 1 NC 15 49 NC
AI 10 53 19 AO 2 NC 16 50 NC
AI 11 52 18 AO 3 NC 17 51 NC
AI 12 51 17 AO 4 NC 18 52 NC
AI 13 50 16 AO 5 NC 19 53 NC
AI 14 49 15 AO 6 NC 20 54 NC
AI 15 48 14 AO 7 NC 21 55 NC
TERMINAL 1 TERMINAL 34
Digital Trigger 0 47 13 Digital Waveform Out 0 NC 22 56 NC
Digital Waveform In 0 46 12 Digital Output 2 TERMINAL 35 TERMINAL 68 NC 23 57 NC
Digital Output 1 45 11 Digital Output 0 NC 24 58 NC
Digital Input 2 44 10 Digital Input 1 NC 25 59 NC
Digital Input 0 43 9 D GND NC 26 60 NC
Counter 1 42 8 D GND NC 27 61 NC
Counter 0 41 7 D GND NC 28 62 NC
PWM 1 40 6 D GND NC 29 63 NC
PWM 0 39 5 D GND NC 30 64 NC
Encoder0.Z 38 4 D GND NC 31 65 NC
Encoder0.B 37 3 D GND NC 32 66 NC
Encoder0.A 36 2 D GND NC 33 67 NC
+5 V 35 1 +5 V NC 34 68 NC

NC = No Connect NC = No Connect
Dimensions:(mm)

20.02±0.20 175.08±0.20

162.29±0.20

TRIG

100.00±0.20
130.50±0.20

CONNECTOR 0

CONNECTOR 1

210.45±0.20

TRIG