Using this Manual,

Contents 10.4

Ordering Information 10.7

®
Tools 10.8
10.4
Floor Stands, Covers,
The Global Leader in Food Cutting Technology And Guards 10.10
10.4
Safety Signs and
Machine Labels 10.14
10.4

Section 10
Slice Gate And
Related Parts 10.18
10.4

Parts Dicing 10.20

10.4

Strip Cutting 10.22

10.4

Slicing 10.26
10.4

Shredding 10.28
10.4
Water Spray System
For The Cutting Unit 10.30
10.4
Impellers And Impeller
Cone Assemblies 10.32
10.4
Circular Spindle
Support Assemblies 10.36
10.4
Slicing Knife Holders,
Inserts, 1 Piece Knives 10.42
10.4
Circular Knife Spindles
Feed Spindles, .038" 10.46
10.4
Circular Knife Spindles
Feed Spindles, .058" 10.56
10.4
Stripper Plates,
Spacers And Shims 10.64
10.4
Crosscut Knife Spindle
Assemblies 10.70
10.4
Shred Spindle Assy's,
Rotating Deflector 10.78
10.4

Diversacut 2110A® Dicer Spindle Assemblies 10.80

10.4

Model DC2110A Lubrication Assembly 10.92

10.4

Parts Manual Motor And Motor

Pulley, Drive Parts 10.98
10.4

2019 Edition Electrical Assemblies 10.102

10.4
Guard lock Switches,
Language Enclosure Fittings 10.134
10.4
Code

E
English
Dimensional Drawings,
Center Of Gravity 10.142
10.2

This page intentionally left blank.

 10.3

Diversacut 2110A® Dicer

Model DC2110A
Parts Manual, 2019 Edition
Publication Description: MANUAL, ENGLISH, PARTS, DC2110A, 2019 EDITION
Publication Number: L3397
Date issued: December 2019

URSCHEL
CORPORATE HEADQUARTERS
1200 Cutting Edge Drive
Chesterton, Indiana 46304 U.S.A.
Corporate: +1.219.464.4811
Fax: +1.219.462.3879
Toll Free: +1.844.URSCHEL (877.2435)
www.urschel.com
Inquiries regarding Technical Publications: [email protected]
All other inquiries: [email protected]

Subsidiaries and sales offices are located in principal cities worldwide. See the website for the location of the
nearest office.

This instruction manual contains the most recent information available and represents the machine as it is
currently manufactured at the time of publication. Urschel Laboratories reserves the right to make changes at
any time without notice. If your machine contains parts not shown, or if there are any questions regarding the
safe operation of this machine, contact Urschel Laboratories or your Urschel representative.

COPYRIGHT© 2019 Urschel Laboratories, Inc., Chesterton, Indiana. All rights reserved. No part of this
manual may be reproduced or transmitted in any form or by any means, electronic or mechanical, including
photocopying and recording, for any purpose without the express written permission of Urschel Laboratories,
Inc.

® Urschel, Diversacut, and Urschelube are registered trademarks of Urschel Laboratories, Inc.
® Acetron is a registered trademark of Quadrant EPP.
® Adobe is a registered trademark of Adobe Systems, Inc.
® Loctite is a registered trademark of Henkel Corp.
® Never-Seez is a registered trademark of Bostik, Inc.
® Nylok is a registered trademark of Nylok Fastener Corp.
 10.4 Parts: Using this Manual
10

Message to the User Instruction and Parts Manuals

Use this Parts Manual with the This Instruction Manual is supplied with
Instruction Manual. The Instruction Manual a Parts Manual. These manuals may be
contains safety, installation, operation updated independently. Visit the Urschel
and service information and must be read website at urschel.com to check for the
and understood by all persons using this latest publications for your machine.
machine.
Learn and follow all the safety rules Ordering Technical Publications
and operating principles in the Instruction
Manual. Follow all warnings, cautions, and To obtain a manual, contact your Urschel
other safety messages in this manual and representative or request a manual through
on the machine. Recognize the safety alert the company website at urschel.com.
symbol m, which indicates a potential You can also email your request to
personal safety hazard. [email protected]. Please include the
If there are any questions regarding the machine model, serial number, the name of
safe operation of this machine, contact your your company and the language required.
Urschel representative. Manuals are available in printed and
electronic forms. Most manuals are
Messages in the Manual available in several languages. Printed
manuals and electronic media (USB drives)
The following messages may be used in are free of charge and postage paid.
this manual: Publications are reviewed and updated
regularly. Check the Urschel website for
m CAUTION the latest publications for your machine
This alert is followed by a statement that
describes a potential hazard which may
result in minor injury.

m WARNING
This alert is followed by a statement that
describes a potential hazard that could
result in serious injury or death.

m DANGER
This alert is followed by a statement that
describes a potential hazard that will result
in serious injury or death.
NOTICE
This word is followed by a statement that
alerts you to key information or instructions.
IMPORTANT
This word is followed by a statement that
alerts you to machine conditions that must
be verified or corrected, or damage to the
machine may occur.
 Parts: Contents 10.5
10

Section 10 Parts
Message to the user, Messages in the Manual,
Instruction and Parts Manuals, Ordering Technical Publications. . . 10.4
Ordering Parts, Returning Parts for Credit
or Repair, Motor Warranty and Repair. . . . . . . . . . . . . . . . . . . 10.7
Tools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.8
Floor Stand, Covers and Guards. . . . . . . . . . . . . . . . . . . . . . . . 10.10
Feed Cover with Discharge Chute. . . . . . . . . . . . . . . . . . . . . . . . 10.12
Safety Signs and Machine Labels, two piece feed/discharge. . . . . 10.14
Safety Signs and Machine Labels, one piece feed/discharge.. . . . 10.16
Slice Gate and Related Parts. . . . . . . . . . . . . . . . . . . . . . . . . . 10.18
Dicing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.20
Strip Cutting with the Circular Knife Spindle Assembly. . . . . . . . . 10.22
Strip Cutting with the Crosscut Knife Spindle Assembly. . . . . . . . 10.24
Slicing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.26
Shredding. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.28
Water Spray System for the Cutting Unit.. . . . . . . . . . . . . . . . . . 10.30
Impellers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.32
Impeller Cone Assemblies.. . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.34
Circular Spindle Support Assembly. . . . . . . . . . . . . . . . . . . . . . 10.36
Circular Spindle Support Assembly with Grease Fittings. . . . . . . . 10.38
Circular Spindle Support Assembly for Granulation. . . . . . . . . . . 10.40
Slicing Knife Holders and Insert Knives. . . . . . . . . . . . . . . . . . . 10.42
Slicing Knives, one piece. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.44
Circular Knife Spindle Assemblies,
.038" thick knives, 1.4" diameter spacers. . . . . . . . . . . . . . . . . 10.46
Circular Knife Spindle Assemblies with
Large Diameter Spacers, .038" thick knives. . . . . . . . . . . . . . . 10.48
Circular Knife Spindle Assemblies with
Feed Discs, .038" thick knives.. . . . . . . . . . . . . . . . . . . . . . . . 10.50
Feed Spindle Assemblies, .038" thick feed discs. . . . . . . . . . . . . 10.52
Feed Discs, .038" thick. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.54
Circular Knife Spindle Assemblies,
.058" thick knives, 1.4" diameter spacers. . . . . . . . . . . . . . . . . 10.56
Circular Knife Spindles with
Large Diameter Spacers, .058" thick knives. . . . . . . . . . . . . . . 10.58
Feed Spindle Assemblies, .058" thick feed discs. . . . . . . . . . . . . 10.60
Feed Discs, .058" thick. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.62
Stripper Plates.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.64
Stripper Plates, secondary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.66
Stripper Plate Spacers and Shims. . . . . . . . . . . . . . . . . . . . . . . 10.68

(continued on the following page)

 10.6 Parts: Contents
10

Section 10 Parts (continued)

Crosscut Knife Spindle Assemblies, 3/32"-1/4" (2.4-6.4mm). . . . . 10.70
Crosscut Knife Spindle Assemblies, 9/32"-.583" (7.1-14.8mm). . . 10.72
Crosscut Knife Spindle Assemblies, .583"-1-1/2" (14.8-38.1mm).. 10.74
Crosscut Knife Spindle Assemblies, heavy duty. . . . . . . . . . . . . . 10.76
Shred Spindle Assemblies and Rotating Deflector. . . . . . . . . . . . 10.78
Spindle Assembly, Impeller Shaft.. . . . . . . . . . . . . . . . . . . . . . . 10.80
Spindle Assembly, Circular Shaft and Drive Couplings. . . . . . . . . 10.82
Spindle Assembly, Circular Shaft and Flexible Coupling. . . . . . . . 10.84
Spindle Assembly, Circular Shaft with Integrated Coupling. . . . . . 10.86
Spindle Assembly, Crosscut Shaft. . . . . . . . . . . . . . . . . . . . . . . 10.88
Spindle Assembly, Jack Shaft. . . . . . . . . . . . . . . . . . . . . . . . . . 10.90
Lubrication Assembly, with circular and crosscut spindles. . . . . . . 10.92
Lubrication Assembly, without crosscut spindles. . . . . . . . . . . . . 10.94
Lubrication Assembly, without circular and crosscut spindles. . . . 10.96
Motor and Motor Pulley.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.98
Drive Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.100
Electrical Assembly Charts. . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.102
Electrical Assembly, with VFD, low/high voltage. . . . . . . . . . . . . 10.104
Electrical Enclosure, with VFD, low/high voltage. . . . . . . . . . . . . 10.106
Electrical Enclosure, with VFD, Door Parts, low/high voltage. . . . . 10.108
Electrical Schematic 43267, with VFD, without CE. . . . . . . . . . . . 10.110
Electrical Assembly, with VFD, CE Compliant. . . . . . . . . . . . . . . 10.114
Electrical Enclosure, with VFD, CE Compliant. . . . . . . . . . . . . . . 10.116
Electrical Enclosure, Door Parts, with VFD, CE Compliant. . . . . . 10.118
Electrical Schematic 43278, with VFD, CE Compliant.. . . . . . . . . 10.120
Electrical Assembly, with Soft Start. . . . . . . . . . . . . . . . . . . . . . 10.124
Electrical Enclosure, with Soft Start. . . . . . . . . . . . . . . . . . . . . . 10.126
Electrical Enclosure, Door Parts, with Soft Start.. . . . . . . . . . . . . 10.128
Electrical Schematic 43281, with Soft Start. . . . . . . . . . . . . . . . . 10.130
Guard Locking Switches, two piece feed/discharge. . . . . . . . . . . 10.134
Guard Locking Switches, one piece feed/discharge. . . . . . . . . . . 10.136
Guard Locking Switch For A Collection Device. . . . . . . . . . . . . . 10.138
Enclosure Fittings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.140
Dimensional Drawing, one piece feed/discharge, wide discharge.. 10.142
Dimensional Drawing, two piece feed/discharge,
small dice discharge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.143
Center Of Gravity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.144
 Parts: Ordering Information 10.7

10
Ordering Parts Customers outside the U.S.A., Canada
and Mexico: Contact your nearest Urschel
Include the following information when representative. Urschel has repair facilities
ordering parts: in several regions around the world. Visit
the website at urschel.com for the address of
• Machine Model and Serial Number the nearest representative.
• Part Quantity
• 5 Digit Part Number Motor Warranty and Repair
• Part Description
The motor has a one-year limited
The serial number of your machine is warranty covering materials and
on the name plate located on the support workmanship. If a motor fails within the
housing above the motor. Do not use the warranty period, contact the nearest
item numbers on the illustrations when Urschel office. Your Urschel service
ordering parts. representative will work with the motor
Customers in the U.S.A.: Orders are manufacturer on warranty claims.
accepted by mail, telephone, facsimile and Unauthorized repair work may void the
email. warranty.
Stainless Motors, Inc. (SMI): If a
Urschel Laboratories, Inc. motor fails outside the warranty period,
1200 Cutting Edge Drive instruct the service center to contact the
Chesterton, Indiana 46304 U.S.A. manufacturer prior to disassembling the
motor. The disassembly procedure for
Telephone: 219-464-4811 stainless steel motors differs from standard
Toll free: 844-877-2435 steel motors. Improper disassembly may
Facsimile: 219-462-3879 damage the motor beyond repair. Contact
Email: [email protected] the company at stainlessmotors.com.
Baldor Electric Company, Inc.: If a
Customers outside the U.S.A.: Contact motor fails outside the warranty period,
your nearest Urschel representative. contact Baldor for the location of an
Urschel has parts inventories in several authorized service center. Contact the
regions around the world. Visit the website company at baldor.com.
at urschel.com for the address of the nearest
representative. Cleaning the Machine and Parts
Before Use
Returning Parts for Credit or Repair
Parts and equipment supplied by
Items must be returned within 30 days of Urschel have not been sanitized. Urschel
purchase and be in their original condition for recommends that the supplied parts
credit. Pack parts securely to avoid damage and equipment be properly cleaned and
during shipment. sanitized prior to use and in accordance
Customers in the U.S.A., Canada with the requirements of the application.
and Mexico: Customers must obtain
a Return Merchandise Authorization
(RMA) number before returning any parts,
exchanging parts and sending parts for
repair. Urschel contact information and
address are listed above.
 10.8 Parts: Tools

10
 Parts: Tools 10.9

Item Quantity Part Number and Description

1 1 11010 - Wrench, combination, 9/16", chrome plated
2 1 98129 - Wrench, combination, 5/8" chrome plated
3 1 98130 - Wrench, combination, 1/2" chrome plated
10
4 1 98132 - Wrench, combination, 3/4" chrome plated
5 1 98304 - Allen Wrench, 3/16", short
6 1 98137 - Wrench, 13 piece set, chrome plated, ball end
7 1 11032 - Socket, 7/16", 6 point, 3/8" drive
8 1 11021 - Socket, 1/2", 12 point, 3/8" drive
9 1 11011 - Socket, 9/16", 12 point, 3/8" drive
10 1 11042 - Feeler Gauge
11 1 62297 - Wrench, “L” handle
12 1 11085 - Tamper Resistant Torx L-Key, T20
13 1 11086 - Tamper Resistant Torx L-Key, T25
14 1 11983 - Torque Wrench, “L” handle, 65 in-lbs., 3/8" drive
15 1 11984 - Hex Bit, 3/16", 3/8" drive
16 1 98136 - Wrench, 8 piece set, “T” handle
17 1 11067 - Torque Wrench, “T” handle, 40 in-lbs.
18 1 11876 - Hex Bit, 3/16", 1/4" drive
19 1 11012 - Hex Bit, 5/16"
20 2 17453 - Protective Glove, medium, 1 glove only (fits hand size 8)
21 1 42939 - Wrench, open end, 1-5/16" x 1-1/2"
22 1 11087 - Release Tool with Handle (includes items 23–24)
23 1 11987 - Release Tool Key
24 1 11988 - Release Tool Bit Holder
25 1 42467 - Wrench, motor tension
26 1 11070 - Grease Gun
27 1 42389 - Tool, shaft extension, DC
28 1 42468 - Bearing Seating Tool
29 1 42567 - Handle For Insert Knife (includes item 30)
30 1 42568 - Pin, locking, 1/4"
31 1 11979 - Wrench, open end, 5/16", long
32 1 98096 - Belt Tension Tester
33 1 43338 - Key, 7mm triangle, s.s.
– 1 11071 - Tool Box (not shown)
– 1 98280 - Grease, ‘0’, Urschelube FDA, cartridge (not shown)

Optional Tools
– 2 17567 - Protective Glove, X-small, 1 glove only (fits hand size 6, not shown)
2 17497 - Protective Glove, small, 1 glove only (fits hand size 7, not shown)
2 17498 - Protective Glove, large, 1 glove only (fits hand size 9, not shown)
2 17566 - Protective Glove, X-large, 1 glove only (fits hand size 10, not shown)
– 1 42425 - Torque Wrench with 5/16" Open End Head Drive (includes items 34–35,
200 inch pounds, used to tighten fastening posts)
34 1 11830 - Torque Wrench
35 1 42424 - Head Drive, open end, 5/16"
36 1 43238 - Crosscut Setting Tool (for adjusting the crosscut bearing spindle)
37 1 98264 - Shim Reference Tool, small (includes item 38; for rebuilding the circular
and crosscut bearing spindles)
38 3 10508 - Socket Head Cap Screw, 10-24 x 3/4", steel
39 1 98265 - Shim Reference Tool, large (includes item 40; for rebuilding the impeller bearing
spindle)
40 3 10509 - Socket Head Cap Screw, 1/4-20 x 3/4", steel
41 1 11671 - Wrench, open end, 7/16" x 1/2", thin (for knife bolts on 3/8" and 1/2" heavy duty
crosscut knife spindles)
42 1 98290 - Wrench, open end, 36 mm (for 43098 circular spindle nut)
– 1 98321 - Universal Joint, 3/8" drive (not shown)
– 1 98331 - Socket, 1/4", 6 point, 3/8" drive (for 43206 fastening posts, not shown)
 10.10 Parts: Floor Stands, Covers and Guards

10
 Parts: Floor Stands, Covers and Guards 10.11

Item Quantity Part Number and Description

1 1 43294 - Floor Stand**, 15" height (381 mm), wide
1 43293 - Floor Stand**, 15" height (381 mm), casters, wide
– 1 12384 - Caster Assembly, plate, set of 4 with fasteners (includes items 2–5)
2 2 12477 - Caster, swivel, plate type
3 2 12528 - Caster, rigid, plate type 10
4 16 10058 - Hex Head Cap Screw, 3/8-16 x 1", s.s.
5 16 10249 - Hex Nut, 3/8-16, s.s., locking, thick
6 1 43127 - Support Housing
7 1 43332 - Guard, electrical box mounting
8 2 * - Washer, flat
9 1 42238 - Handle, knob
10 1 42239 - Handle, latch
11 1 42920 - Case Reinforcement
12 1 10429 - Flat Head Socket Cap Screw, 3/8-16 x 1", s.s.
13 4 10460 - Hex Head Cap Screw, 3/4-10 x 3-3/4", s.s.
14 4 10399 - Hex Nut, 3/4-10, locking
15 1 53247 - Hopper Extension
16 4 10039 - Hex Head Cap Screw, 1/4-20 x 1", s.s.
17 4 19603 - Spacer, 7/16"
18 4 10230 - Hex Nut, 1/4-20, s.s., locking, thick
19 1 42929 - Discharge Chute, slice/small dice
20 1 10075 - Hex Head Cap Screw, 1/2-13 x 1-3/4", s.s.
21 1 10016 - Lock Washer, 1/2", s.s.
22 1 10059 - Hex Head Cap Screw, 3/8-16 x 1-1/4", s.s.
23 1 10270 - Washer, flat, 3/8", s.s., thick
24 1 10015 - Lock Washer, 3/8", s.s.
25 1 43203 - Feed Cover (includes items 26–31)
26 1 42255 - Hinge, feed cover
27 2 42257 - Washer, flat, .630" I.D. x 1.00" O.D. x .100"
28 3 10429 - Flat Head Socket Cap Screw, 3/8-16 x 1", s.s.
29 1 42259 - Hinge, feed cover
30 3 10058 - Hex Head Cap Screw, 3/8-16 x 1", s.s.
31 3 10374 - Hex Cap Nut, 3/8-16, s.s., Nylok
32 1 55211 - Draw Latch
33 2 10037 - Hex Head Cap Screw, 1/4-20 x 1/2", s.s.
34 2 10365 - Hex Nut, 1/4-20, s.s., locking, thin
35 1 55118 - Strike Latch
36 2 10089 - Socket Head Cap Screw, 1/4-20 x 1/2", s.s.
37 1 42895 - Discharge Chute, multi-purpose, wide (includes items 38–39)
38 1 42972 - Baffle, lower, multi-purpose
39 2 10307 - Hex Head Cap Screw, 5/16-18 x 1/2", Nylok

* Contact an Urschel representative.

** Use floor stands on page 10.138 for machines equipped with the guard locking switch for a collection device.
 10.12 Parts: Feed Cover with Discharge Chute

10
 Parts: Feed Cover with Discharge Chute 10.13

Item Quantity Part Number and Description

1 1 43156 - Feed Cover/Discharge, wide (includes items 2–9)
2 1 42973 - Baffle, lower, feed cover/discharge
3 2 10037 - Hex Head Cap Screw, 5/16-18 x 1/2", Nylok
4 1 42259 - Hinge, feed cover
5 3 10058 - Hex Head Cap Screw, 3/8-16 x 1", s.s. 10
6 3 10374 - Hex Cap Nut, 3/8-16, s.s., Nylok
7 1 42255 - Hinge, feed cover
8 3 10429 - Flat Head Socket Cap Screw, 3/8-16 x 1", s.s.
9 2 42257 - Washer, flat, .630" I.D. x 1.00" O.D. x .100"
10 1 42922 - Baffle, inner
11 2 10074 - Hex Head Cap Screw, 1/2-13 x 1-1/2", s.s.
12 2 10016 - Lock Washer, 1/2", s.s.
 10.14 Parts: Safety Signs and Machine Labels, two piece feed/discharge

Item 3 label is located

behind the belt guard.

10
 Parts: Safety Signs and Machine Labels, two piece feed/discharge 10.15

Part Number
Language
Language* Item 1 Item 2 Item 3 Item 4 Item 5 Item 6** Item 7
Code* Feed Opening Discharge Chute Removed Guard Caution Label External/Internal Danger Label Warning Label,
Disconnect Current Release Tool

English/Spanish – 11662 11663 11665 11666 21361 12821 98141

Arabic AR 98113 98115 98117 98125 21570 21594 21651
Chinese CH 11724 11725 11727 11723 21360 98030 21564
Croatian CR 98112 98114 98116 98126 98185 – 98186 10
Czech CZ 11868 11869 11871 11872 11999 98023 98148
Danish DA 11793 11794 11796 11797 98074 12830 21652
Dutch DU 11716 11717 11719 11720 21367 12824 98181
Estonian ES 98166 98165 98168 98167 – – –
Finnish FI 11758 11759 11761 11762 21422 12829 98223
French F 11674 11675 11677 11678 21362 12822 21565
German GE 11681 11682 11684 11685 21363 12823 98142
Greek GR 11737 11738 11740 11741 21394 12828 21567
Hungarian HU 11772 11773 11775 11776 98261 98263 98262
Indonesian IN 11751 11752 11754 11755 21358 98226 21653
Italian IT 11702 11703 11705 11706 21365 12826 98149
Japanese J 11688 11689 11691 11692 21364 98240 98179
Korean KO 98228 98229 98230 98231 98232 98235 98233
Polish POL 11730 11731 11733 11734 21395 21228 98150
Portuguese PO 11695 11696 11698 11699 21388 12827 98175
Russian RU 11744 11745 11747 11748 21387 21467 21654
Serbian SB 11109 11110 11112 11108 98108 21382 98109
Slovenian SL 98348 98347 98350 98349 – – –
Swedish SW 11709 11710 11712 11713 21366 12825 21411
Thai TH 11946 11947 11949 11950 98013 98227 98224
Turkish TU 11765 11766 11768 11769 21464 98097 23892
Quantity 4 2 3 1 1 1 2

Item Quantity Part Number and Description

8 § 12714 - Hazard Alert Label, electrical, 200 volts
12715 - Hazard Alert Label, electrical, 208 volts
12716 - Hazard Alert Label, electrical, 220 volts
12717 - Hazard Alert Label, electrical, 230 volts
12718 - Hazard Alert Label, electrical, 240 volts
12719 - Hazard Alert Label, electrical, 380 volts
12720 - Hazard Alert Label, electrical, 400 volts
12721 - Hazard Alert Label, electrical, 415 volts
12723 - Hazard Alert Label, electrical, 460 volts
12724 - Hazard Alert Label, electrical, 575 volts
9 § 21641 - Hazard Alert Label, electrical, 380Y/220
21642 - Hazard Alert Label, electrical, 400Y/230
21643 - Hazard Alert Label, electrical, 415Y/240
21640 - Hazard Alert Label, electrical, 460Y/266
10 2 42297 - Label, guard locking switch
11 1 11326 - Urschel Label, 1.5" x 8.25"
12 1 43240 - Label, DiversaCut 2110A
13 1 53360 - Label, manual release tool (located inside electrical enclosure)

* The English/Spanish label has English in the top language area. All other labels are bilingual with English in
the bottom language area. These labels also have a language code.
** Used only on CE compliant enclosure with variable frequency drive, located inside the electrical enclosure.
§ One Hazard Alert Label of corresponding voltage is supplied with the machine.
 10.16 Parts: Safety Signs and Machine Labels, one piece feed/discharge

Item 3 label is located

behind the belt guard.

10
 Parts: Safety Signs and Machine Labels, one piece feed/discharge 10.17

Part Number
Language
Language* Item 1 Item 2 Item 3 Item 4 Item 5 Item 6** Item 7
Code* Feed Opening Discharge Chute Removed Guard Caution Label External/Internal Danger Label Warning Label,
Disconnect Current Release Tool

English/Spanish – 11662 11663 11665 11666 21361 12821 98141

Arabic AR 98113 98115 98117 98125 21570 21594 21651
Chinese CH 11724 11725 11727 11723 21360 98030 21564
Croatian CR 98112 98114 98116 98126 98185 – 98186 10
Czech CZ 11868 11869 11871 11872 11999 98023 98148
Danish DA 11793 11794 11796 11797 98074 12830 21652
Dutch DU 11716 11717 11719 11720 21367 12824 98181
Estonian ES 98166 98165 98168 98167 – – –
Finnish FI 11758 11759 11761 11762 21422 12829 98223
French F 11674 11675 11677 11678 21362 12822 21565
German GE 11681 11682 11684 11685 21363 12823 98142
Greek GR 11737 11738 11740 11741 21394 12828 21567
Hungarian HU 11772 11773 11775 11776 98261 98263 98262
Indonesian IN 11751 11752 11754 11755 21358 98226 21653
Italian IT 11702 11703 11705 11706 21365 12826 98149
Japanese J 11688 11689 11691 11692 21364 98240 98179
Korean KO 98228 98229 98230 98231 98232 98235 98233
Polish POL 11730 11731 11733 11734 21395 21228 98150
Portuguese PO 11695 11696 11698 11699 21388 12827 98175
Russian RU 11744 11745 11747 11748 21387 21467 21654
Serbian SB 11109 11110 11112 11108 98108 21382 98109
Slovenian SL 98348 98347 98350 98349 – – –
Swedish SW 11709 11710 11712 11713 21366 12825 21411
Thai TH 11946 11947 11949 11950 98013 98227 98224
Turkish TU 11765 11766 11768 11769 21464 98097 23892
Quantity 4 2 3 1 1 1 2
Item Quantity Part Number and Description
8 § 12714 - Hazard Alert Label, electrical, 200 volts
12715 - Hazard Alert Label, electrical, 208 volts
12716 - Hazard Alert Label, electrical, 220 volts
12717 - Hazard Alert Label, electrical, 230 volts
12718 - Hazard Alert Label, electrical, 240 volts
12719 - Hazard Alert Label, electrical, 380 volts
12720 - Hazard Alert Label, electrical, 400 volts
12721 - Hazard Alert Label, electrical, 415 volts
12723 - Hazard Alert Label, electrical, 460 volts
12724 - Hazard Alert Label, electrical, 575 volts
9 § 21641 - Hazard Alert Label, electrical, 380Y/220
21642 - Hazard Alert Label, electrical, 400Y/230
21643 - Hazard Alert Label, electrical, 415Y/240
21640 - Hazard Alert Label, electrical, 460Y/266
10 2 42297 - Label, guard locking switch
11 1 11326 - Urschel Label, 1.5" x 8.25"
12 1 43240 - Label, DiversaCut 2110A
13 1 53360 - Label, manual release tool (located inside electrical enclosure)

* The English/Spanish label has English in the top language area. All other labels are bilingual with English in
the bottom language area. These labels also have a language code.
** Used only on CE compliant enclosure with variable frequency drive, located inside the electrical enclosure.
§ One Hazard Alert Label of corresponding voltage is supplied with the machine.
 10.18 Parts: Slice Gate and Related Parts

10
 Parts: Slice Gate and Related Parts 10.19

Item Quantity Part Number and Description

1 1 43140 - Case, crinkle (includes items 3–4)
1 43139 - Case, straight (not shown, includes items 3–4)
2 1 43193 - Case, crinkle, heavy duty (not shown, includes items 3–4; see detail, requires
one 42875 flat head screw, item 33 for the center hole)
1 43192 - Case, straight, heavy duty (includes items 3–4; see detail, requires
one 42875 flat head screw, item 33 for the center hole)
3 2 22081 - Dowel Pin, 3/8" x 31/32"
4 2 42772 - Dowel Pin, 1/4", threaded
5 7 10061 - Hex Head Cap Screw, 3/8-16 x 1-3/4", s.s.
6 7 10015 - Lock Washer, 3/8", s.s. 10
7 1 43129 - Slice Gate, crinkle
1 43128 - Slice Gate, straight (not shown)
8 1 43130 - Guard, slice gate
9 2 10307 - Hex Head Cap Screw, 5/16-18 x 1/2", Nylok
10 1 53007 - Hinge Plate
11 8 10307 - Hex Head Cap Screw, 5/16-18 x 1/2", Nylok
12 8 38064 - Washer, flat, 5/16", s.s.
13 1 43131 - Chip Guard, left, extended (includes item 14)
14 1 43133 - Bushing, chip guard
15 1 10635 - Hex Head Cap Screw, 3/8-16 x 1", s.s., Nylok
16 1 10638 - Washer, flat, 3/8", s.s., oversized
17 1 43132 - Chip Guard, right, extended (includes item 18)
18 1 43133 - Bushing, chip guard
19 1 43194 - Chip Guard, right, extended, metric (includes item 20)
20 1 43133 - Bushing, chip guard
21 4 10402 - Flat Head Socket Cap Screw, 5/16-18 x 3/4", s.s.
22 1 42640 - Drive Coupling*, 2.3" O.D. (includes item 23)
23 2 37040 - Dowel Pin, 1/4" x 5/8", 416, s.s.
24 3 10593 - Lock Washer, 1/4", vibration resistant
25 3 10592 - Button Head Screw, 1/4-20 x 5/8"
26 1 43134 - Bar, chip guard
27 1 43135 - Knob, slice gate adjustment
28 2 43247 - Washer, bronze, .65" I.D. x 1.00" O.D. x .06"
29 1 43136 - Adjustment Shaft, slice gate (includes item 30)
30 1 10137 - Socket Set Screw, 1/4-20 x 3/8", cup point, s.s.
31 1 43137 - Knob, locking, slice gate
32 1 43138 - Bar, slice gate
33 1 42875 - Flat Head Screw, 3/8-16 x 11/16", s.s.
34 1 43228 - Handle, short (replaces 2 of items 11 and 12; part numbers 10307 and 38064)
35 2 43229 - Handle, long (replaces 2 of items 11 and 12; part numbers 10307 and 38064)

* For optional drive couplings and circular shaft spindle assemblies, see Spindle Assembly, Circular Shaft, and
Drive Couplings and the pages following.
See Section 6: Machine Setup for information on the use of crinkle and straight slice cases and gates.
 10.20 Parts: Dicing

10
 Parts: Dicing 10.21

Item Quantity Part Number and Description

Dicing only
1 1 * - Knife, slicing
2 2 42672 - Fastening Post
3 1 * - Stripper Plate
4 3 10044 - Hex Head Cap Screw, 5/16-18 x 5/8", s.s.
5 1 * - Stripper Plate Spacer
6 3 10424 - Socket Head Cap Screw, 1/4-20 x 3/8", s.s., low head
7 1 * - Feed Spindle and Circular Support Assembly
8 2 10249 - Hex Nut, 3/8-16, s.s., locking, thick
9 1 * - Crosscut Knife Spindle Assembly
10 3 24138 - Socket Head Cap Screw, 3/8-16 x 1-1/4", hard
10
Alternate parts
11 2 43206 - Fastening Post (replaces item 2)

* Cutting parts begin on page 10.42. Cutting parts are listed in the order that product flows through the
machine: slicing knives, circular knife and feed spindle assemblies, stripper plates, and crosscut knife and
shred spindle assemblies.
 10.22 Parts: Strip Cutting with the Circular Knife Spindle Assembly

10
 Parts: Strip Cutting with the Circular Knife Spindle Assembly 10.23

Item Quantity Part Number and Description

Strip cutting with the circular knife spindle
1 1 * - Knife, slicing
2 2 42672 - Fastening Post
3 1 * - Stripper Plate
4 3 10044 - Hex Head Cap Screw, 5/16-18 x 5/8", s.s.
5 1 * - Stripper Plate Spacer
6 3 10424 - Socket Head Cap Screw, 1/4-20 x 3/8", s.s., low head
7 1 * - Circular Knife Spindle and Circular Support Assembly (use with 42575 inner guide)
8 1 42575 - Inner Guide, slice/circular only
9 2 10249 - Hex Nut, 3/8-16, s.s., locking, thick

Alternate parts
10 2 43206 - Fastening Post (replaces item 2)

NOTICE 10
The crosscut bearing spindle may be replaced by 42658 plug (see Slicing on the following pages); use 42659
timing belt if the crosscut bearing spindle is not installed.

Strip cutting with the circular knife spindle and rotating deflector
11 1 * - Knife, slicing
12 2 42672 - Fastening Post
13 1 * - Stripper Plate
14 3 10044 - Hex Head Cap Screw, 5/16-18 x 5/8", s.s.
15 1 * - Stripper Plate Spacer
16 3 10424 - Socket Head Cap Screw, 1/4-20 x 3/8", s.s., low head
17 1 * - Circular Knife Spindle and Circular Support Assembly
18 2 10249 - Hex Nut, 3/8-16, s.s., locking, thick
19 1 43025 - Rotating Deflector (mounts to the crosscut shaft spindle assembly; used to deflect
product away from the spindle housing when no crosscut knife spindle is used)
20 3 24138 - Socket Head Cap Screw, 3/8-16 x 1-1/4", hard

Alternate parts
21 2 43206 - Fastening Post (replaces item 12)

* Cutting parts begin on page 10.42. Cutting parts are listed in the order that product flows through the
machine: slicing knives, circular knife and feed spindle assemblies, stripper plates, and crosscut knife and
shred spindle assemblies.
 10.24 Parts: Strip Cutting with the Crosscut Knife Spindle Assembly

10
 Parts: Strip Cutting with the Crosscut Knife Spindle Assembly 10.25

Item Quantity Part Number and Description

Strip cutting with the crosscut knife spindle and a feed spindle to aid product flow
1 1 * - Knife, slicing
2 2 42672 - Fastening Post
3 1 * - Stripper Plate
4 3 10044 - Hex Head Cap Screw, 5/16-18 x 5/8", s.s.
5 1 * - Stripper Plate Spacer
6 3 10424 - Socket Head Cap Screw, 1/4-20 x 3/8", s.s., low head
7 1 * - Feed Spindle and Circular Support Assembly
8 2 10249 - Hex Nut, 3/8-16, s.s., locking, thick
9 1 * - Crosscut Knife Spindle Assembly
10 3 24138 - Socket Head Cap Screw, 3/8-16 x 1-1/4", hard

Alternate parts
11 2 43206 - Fastening Post (replaces item 2)
10
* Cutting parts begin on page 10.42. Cutting parts are listed in the order that product flows through the
machine: slicing knives, circular knife and feed spindle assemblies, stripper plates, and crosscut knife and
shred spindle assemblies.
 10.26 Parts: Slicing

10
 Parts: Slicing 10.27

Item Quantity Part Number and Description

Slice only, circular and crosscut shaft spindle assemblies replaced with plugs
1 1 42826 - Plug, circular spindle (includes item 2)
2 1 71068 - O-ring, 1/16" x 4-1/4" x 4-3/8", Viton
3 4 10110 - Socket Head Cap Screw, 3/8-16 x 3/4", s.s.
4 1 42658 - Plug, crosscut spindle (includes item 5)
5 1 42210 - O-ring, 3/32" x 5-1/2" x 5-11/16", Viton
6 4 10113 - Socket Head Cap Screw, 3/8-16 x 1-1/4", s.s.
7 1 * - Slicing Knife Holder
8 1 * - Slicing Knife
9 1 42631 - Inner Guide, slice only
10 2 10110 - Socket Head Cap Screw, 3/8-16 x 3/4", s.s.

NOTICE
Use 42659 timing belt when the crosscut bearing spindle or the circular bearing spindle has been replaced by a
plug.

Slice only, circular and crosscut shaft spindle assemblies in place 10

11 1 * - Slicing Knife Holder
12 1 * - Slicing Knife
13 1 42631 - Inner Guide, slice only
14 2 10110 - Socket Head Cap Screw, 3/8-16 x 3/4", s.s.
2 10326 - Socket Head Cap Screw, 3/8-16 x 1/2", s.s. (for the slicing knife holder when used
without the Inner Guide, item 13)

* Cutting parts begin on page 10.42. Cutting parts are listed in the order that product flows through the
machine: slicing knives, circular knife and feed spindle assemblies, stripper plates, and crosscut knife and
shred spindle assemblies.
 10.28 Parts: Shredding

10
 Parts: Shredding 10.29

Item Quantity Part Number and Description

Typical setup for shredding meat; other setups may be required for best results
1 1 * - Slicing Knife, scalloped
2 1 * - Slicing Knife Holder
3 2 42672 - Fastening Post
4 1 * - Circular Knife Spindle and Circular Support Assembly
5 2 10249 - Hex Nut, 3/8-16, s.s., locking, thick
6 1 * - Spindle Assembly, crosscut, shred
7 3 24138 - Socket Head Cap Screw, 3/8-16 x 1-1/4", hard

Alternate parts
8 2 43206 - Fastening Post (replaces item 3)

* Cutting parts begin on page 10.42. Cutting parts are listed in the order that product flows through the
machine: slicing knives, circular knife and feed spindle assemblies, stripper plates, and crosscut knife and
shred spindle assemblies.

10
 10.30 Parts: Water Spray System for the Cutting Unit

REF. 4

REF. 8

REF. 9

C
Drill 35/64" (.546", 13.9 mm)
B 2 holes centered on feed cover
C
10 B 1.50"
(38.1 mm)

Water Spray System

comes fully assembled A
Measure between nozzles
 Parts: Water Spray System for the Cutting Unit 10.31

Item Quantity Part Number and Description

1 1 43251 - Water Spray System Assembly* (includes items 2–9)

2 1 53545 - Valve, ball
3 1 53547 - Pipe Nipple, 1/4" x 1-1/2" long, s.s.
4 2 53549 - Fitting, 90 degree, elbow, s.s.
5 1 43250 - Pipe Nipple, 1/4" x 3-1/2" long, s.s.
6 1 53548 - Fitting, tee, s.s.
7 1 42480 - Pipe Nipple, 1/4" x 3" long, s.s.
8 * 42497 - Washer, Teflon, .50" I.D. x .75" O.D. x .031"
9 2 53550 - Nozzle, 80 degree, flat spray, s.s.

* The water spray assembly can be added to a machine that was not originally so equipped. The assembly can
also be used with air for dry products. The water spray system comes fully assembled and ready for installation.
Install the assembly as follows:

(A) Measure the distance between the nozzles. (B) Drill 2 holes, 35/64" (.546", 13.9 mm) diameter, at the
measured distance apart, 1.50" (38.1mm) from the edge of the feed cover and centered side-to-side as shown.
(C) Remove the nozzles and install the pipe assembly. Use up to two Teflon washers at each nozzle location if
necessary. Tighten the spray nozzles into the tee and elbow and orient the direction of spray.

10
 10.32 Parts: Impellers

53075 - Impeller, 4 paddle, 14.8" opening 42863 - Impeller, 4 paddle, 14.8" opening, heavy duty

53076 - Impeller, 6 paddle, 14.8" opening 53077 - Impeller, 8 paddle, 14.8" opening

10

53362 - Impeller, 10 paddle, 14.8" opening 53523* - Impeller, 10 paddle, 14.8" angled

42668 - Impeller, 12 paddle, 14.8" opening 53487 - Impeller, 14 paddle, 14.8" opening
 Parts: Impellers 10.33

53514* - Impeller, 4 paddle, 2 channel 53517* - Impeller, 4 paddle, 3 channel

* Contact an Urschel representative for information on the use of this impeller.

Item Quantity Part Number and Description

1 1 ** - Impeller
2 8 10058 - Hex Head Cap Screw, 3/8-16 x 1", s.s.

** See the previous page and above.

10
 10.34 Parts: Impeller
subtitle Cone Assemblies

10
 Parts: Impeller Cone
Parts:
Assemblies
subtitle 10.35

Item Quantity Part Number and Description

1 1 * - Impeller Cone Assembly (Acetron® GP plastic; includes items 2–5)
2 1 42964 - Impeller Cone Detail, mounting plate
3 1 42894 - Impeller Cone Detail, shaft
4 1 * - Impeller Cone Detail
5 1 42959 - Impeller Cone Detail, cap
6 4 10058 - Hex Head Cap Screw, 3/8-16 x 1", s.s.

* See chart below.

Item 1 Item 4, Impeller Cone Detail

Impeller Cone
Diameter Part Number
Assembly
Part Number inch mm
42965 7.6 193 42960
42966 10 254 42961
42967 12 305 42962
42968 15 381 42963

10
 10.36 Parts: Circular Spindle Support Assembly

10
 Parts: Circular Spindle Support Assembly 10.37

Item Quantity Part Number and Description

1 1 * - Circular Knife Spindle Assembly
2 1 * - Circular Knife Spindle Assembly with Feed Discs
3 1 * - Circular Knife Spindle Assembly, feed
4 1 42284 - Circular Support Assembly (includes items 5–16)
5 1 42287 - Circular Support Assembly Detail, top
6 1 42286 - Circular Support Assembly Detail, side (includes item 7)
7 2 42304 - Dowel Pin, 5/16" x 1", 416 s.s.
8 4 10059 - Hex Head Cap Screw, 3/8-16 x 1-1/4", s.s.
9 4 10015 - Lock Washer, 3/8", s.s.
10 1 42285 - Circular Support Assembly Detail, side (includes item 11)
11 2 42304 - Dowel Pin, 5/16" x 1", 416 s.s.
12 2 42261 - Ball Bearing, s.s.
13 2 42506 - Slice Guide
14 4 10086 - Socket Head Cap Screw, 10-24 x 5/8", s.s.
15 1 42260 - Baffle, circular
16 3 10251 - Hex Head Cap Screw, 1/4-20 x 1/2", Nylok

* Cutting parts begin on page 10.42. Cutting parts are listed in the order that product flows through the
machine: slicing knives, circular knife and feed spindle assemblies, stripper plates, and crosscut knife and
shred spindle assemblies.

Alternate parts
17 2 42575 - Inner Guide, slice/circular only
18 2 42860 - Slice Guide**, long (replaces item 13)
– 2 43258 - Ball Bearing, s.s., hybrid (not shown, replaces item 12)

** Used to help prevent product from escaping the cutting zone and building up on the circular support assembly.
Do not use with thick slicing knives and knife holders, crinkle slicing knives and the large diameter circular
10
spindle nut.
 10.38 Parts: Circular
subtitle Spindle Support Assembly with Grease Fittings

10
 Parts: Circular Spindle Support Assembly with Grease
Parts: Fittings
subtitle 10.39

Item Quantity Part Number and Description

1 1 * - Circular Knife Spindle Assembly
2 1 * - Circular Knife Spindle Assembly with Feed Discs
3 1 * - Circular Knife Spindle Assembly, feed
4 1 42903 - Circular Support Assembly, grease (includes items 5–18)
5 1 42287 - Circular Support Assembly Detail, top
6 1 42904 - Circular Support Assembly Detail, left (includes items 7–8)
7 2 42304 - Dowel Pin, 5/16" x 1", 416 s.s.
8 1 11401 - Grease Fitting, 1/8", straight, s.s.
9 4 10059 - Hex Head Cap Screw, 3/8-16 x 1-1/4", s.s.
10 4 10015 - Lock Washer, 3/8", s.s.
11 1 42905 - Circular Support Assembly Detail, right (includes item 12–13)
12 2 42304 - Dowel Pin, 5/16" x 1", 416 s.s.
13 1 11401 - Grease Fitting, 1/8", straight, s.s.
14 2 42906 - Ball Bearing, s.s., grease
15 2 42506 - Slice Guide
16 4 10086 - Socket Head Cap Screw, 10-24 x 5/8", s.s.
17 1 42260 - Baffle, circular
18 3 10251 - Hex Head Cap Screw, 1/4-20 x 1/2", Nylok

* Cutting parts begin on page 10.42. Cutting parts are listed in the order that product flows through the
machine: slicing knives, circular knife and feed spindle assemblies, stripper plates, and crosscut knife and
shred spindle assemblies.

Alternate parts
19 2 42860 - Slice Guide**, long (replaces item 15)

** Used to help prevent product from escaping the cutting zone and building up on the circular support assembly.
Do not use with thick slicing knives and knife holders, crinkle slicing knives and the large diameter circular
10
spindle nut.

IMPORTANT
The 43258 hybrid bearings (listed as alternate parts on the previous and following pages) cannot be used with
this assembly.
 10.40 Parts: Circular Spindle Support Assembly for Granulation

10
 Parts: Circular Spindle Support Assembly for Granulation 10.41

Item Quantity Part Number and Description

1 1 * - Circular Knife Spindle Assembly
2 1 42985 - Circular Support Assembly, granulation (includes items 3–15)
3 1 42982 - Circular Support Assembly, top, granulation
4 1 42286 - Circular Support Assembly Detail, side (includes item 5)
5 2 42304 - Dowel Pin, 5/16" x 1", 416 s.s.
6 4 10059 - Hex Head Cap Screw, 3/8-16 x 1-1/4", s.s.
7 4 10015 - Lock Washer, 3/8", s.s.
8 1 42285 - Circular Support Assembly Detail, side (includes item 9)
9 2 42304 - Dowel Pin, 5/16" x 1", 416 s.s.
10 2 42261 - Ball Bearing, s.s.
11 2 42983 - Slice Guide, tall (do not use with heavy duty slicing knives or holders)
12 4 10086 - Socket Head Cap Screw, 10-24 x 5/8", s.s.
13 1 42260 - Baffle, circular
14 5 10251 - Hex Head Cap Screw, 1/4-20 x 1/2", Nylok
15 1 42984 - Cover, circular support assembly, 3/4"
16 1 42849 - Cover, circular support, 1" (optional, replaces item 15 for larger slice setting)

Alternate parts
– 2 43258 - Ball Bearing, s.s., hybrid (not shown, replaces item 10)

* Cutting parts begin on page 10.42. Cutting parts are listed in the order that product flows through the
machine: slicing knives, circular knife and feed spindle assemblies, stripper plates, and crosscut knife and
shred spindle assemblies.

10
 10.42 Parts: Slicing Knife Holders and Insert Knives

Insert Knives
53178 - Knife, slicing, straight, replaceable insert (use with
knife holder for straight knife)
42650 - Knife, slicing, scalloped, replaceable insert (use with
.076" (1.9mm)
knife holder for straight knife)
53481 - Knife, slicing, crinkle, replaceable insert (.076" deep
.125" (3.2mm) crinkle; use with knife holder for crinkle knife)
53561 - Knife, slicing, deep crinkle, replaceable .125" (use
.145" (3.7mm) with 42671 or 42974 holders; see charts 3 and 4)
42847 - Knife, slicing, deep crinkle, replaceable .125" (use
with 42845 or 42846 holders; see charts 3 and 4)
Chart 1 - Knife Holder Feature, Abbreviation and Description Restrictions
2 STD - Standard Do not use with .058" thick circular
3 The standard knife holder (straight and crinkle) is .312" thick (1), knives and feed discs. Straight and
slots (2) are .070" wide and clearance from the shear edge (3) to the crinkle insert knives require different
crosscut knives is .025" (.635 mm). In Chart 2, knife holder features knife holders; do not use crinkle
are standard unless otherwise indicated. For example, a holder listed crosscut knives with a straight slicing
as WS125 (Wide Slot, .125") is standard thickness and crosscut knife holder.
1 clearance.

4 WS - Wide Slot
Not recommended for soft products
Slots (4) are wider than .070" (1.8 mm); slot width in decimal inches that have incomplete cuts due to
follows the abbreviation in Chart 2, for example WS125 indicates a slot product deforming into the slots.
width of .125".

RC - Reduced Clearance Use with crosscut knife spindles with

6 Used to reduce the clearance between the crosscut knives (5) and narrow knives (sizes 3/32"–1/4";
the shear edge (6) of the slicing knife to .012"–.015" (.30–.38 mm); 2.4–6.4 mm) and heavy duty crosscut
standard is .025" (.64 mm) spindles only.
10 5
7 HD - Heavy Duty Slices will be .050"–.060" (1.3–1.5 mm)
This knife holder is thicker in the area that holds the knife (7). thinner than the slice setting indicates.

THK - Thick Slices will be .050"–.060" (1.3–1.5 mm)

This knife holder is .372" (9.4 mm) thick (8); standard knife holder is thinner than the slice setting indicates.
.312" (7.9 mm) thick. Do not use 42860 long slice guides.
(slice guides mount to the circular
8 support sides).

9 GR - Grooved None
The grooves (9) help prevent the product from sticking to the knife
surface.

INS - Slicing Knife Holder with Insert Important restrictions apply; contact an
Reduces clearance to the crosscut knives to .003"–.005" (.08–.13 mm). Urschel representative before ordering
42957 - Slicing Knife Holder Insert, -.020" these parts.
42957 42958 - Slicing Knife Holder Insert, -.025"
42958 10479 (5) 10479 - Flat Head Socket Cap Screw, 10-24 x 5/16", s.s.

No Slots Do not use with circular knives; use the

For slice only or use with crosscut knife spindle; grooved or flat knife holder and corresponding insert
(shown); use with feed discs if necessary to aid product feed. See knife listed in chart 3 only.
chart 3.

See Section 6 Machine Setup for additional information about slicing knife features.
 Parts: Slicing Knife Holders and Insert Knives 10.43

Item Quantity Part Number

Slicing Knife Holders withand Description
slots
Chart 2 Example:
Slot Feature
Part Number is followed by the slot spacing in inches and the following abbreviations.
Circular Part
Spacing Abbreviation
STD = Standard THK = Thick GR - Grooved Number
Knife and (inch) (see previous page)
HD = Heavy Duty RC = Reduced Clearance INS - Insert
Feed Disc WS = Wide Slot , slot width, decimal inch
Spacing All features are standard (STD) unless otherwise indicated. 42945 - 1/8 (HD, THK, RC)
inch mm Straight Cut Crinkle Cut .076"
42372 - 1/8 (STD) 42550 - 1/8 (RC) 42945 - 1/8 (HD, THK, RC) 43027 - 1/8 (GR)
1/8 3.2 42423 - 1/8 (STD)
43075 - 1/8 (INS)
.150 3.8 ---- 42950 - .150 (STD)
42439 - 5/32 (STD) 42636 - 5/32 (WS 093) 43024 - 5/32 (HD, THK, RC) 43044 - 5/32 (GR)
5/32 4.0 ----
42956 - 5/32 (INS) 42600 - 5/32 (RC)
42373 - 3/16 (STD) 42637 - 3/16 (WS 125) 42647 - 3/16 (RC) 42944 - 3/16 (GR)
3/16 4.8 42942 - 3/16 (STD)
43252 - 3/16 (HD, THK, RC)
7/32 5.6 43249 - 7/32 (STD) ----
42372 - 1/8 (STD) 42550 - 1/8 (RC) 42945 - 1/8 (HD, THK, RC) 43075 - 1/8 (INS) 42444 - 1/4 (STD)
1/4 6.4
42374 - 1/4 (STD) 42629 - 1/4 (WS 125) 42979 - 1/4 (HD, THK, RC) 43255 - 1/4 (WS 125)
9/32 7.1 42641 - 9/32 (STD) 42836 - 9/32 (WS 125) 42818 - 9/32 (STD)
.290 7.4 42764 - .290 (STD) ----
19/64 7.5 42591 - 19/64 (STD) ----
42745 - .300 (STD)
.300 7.6 42744 - .300 (STD) 42861 - .300 (WS 125) 43058* - .300
(See Chart 4)
5/16 7.9 42375 - 5/16 (STD) 43044 - 5/32 (GR) 42747 - 5/16 (WS 188) 43091 - 5/16 (WS 125) ----
11/32 8.7 42799 - 11/32 (STD) ----
42372 - 1/8 (STD) 42550 - 1/8 (RC) 42945 - 1/8 (HD, THK, RC) 43075 - 1/8 (INS) 42942 - 3/16 (STD)
3/8 9.5 42373 - 3/16 (STD) 42637 - 3/16 (WS 125) 42647 - 3/16 (RC) 42445 - 3/8 (STD)
42376 - 3/8 (STD) 42630 - 3/8 (WS 188) 43028 - 3/8 (GR)
7/16 11.1 43249 - 7/32 (STD) 42634 - 7/16 (STD) 43043 - 7/16 (RC) 43298 - 7/16 (STD)
42372 - 1/8 (STD) 42550 - 1/8 (RC) 42945 - 1/8 (HD, THK, RC) 43075 - 1/8 (INS)
42444 - 1/4 (STD)
1/2 12.7 42374 - 1/4 (STD) 42629 - 1/4 (WS 125) 42979 - 1/4 (HD, THK, RC)
43255 - 1/4 (WS)
42377 - 1/2 (STD) 10
9/16 14.3 42836 - 9/32 (WS 125) 42373 - 3/16 (STD) 42647 - 3/16 (RC) 42840 - 9/16 (WS 125) ----
19/32 15.1 42591 - 19/64 (STD) 42827 - 19/32 (WS 125) ----
42372 - 1/8 (STD) 42550 - 1/8 (RC) 42945 - 1/8 (HD, THK, RC) 42375 - 5/16 (STD)
5/8 15.9 42423 - 1/8 (STD)
42747 - 5/16 (WS 188) 42378 - 5/8 (STD)
42372 - 1/8 (STD) 42550 - 1/8 (RC) 42945 - 1/8 (HD, THK, RC) 43075 - 1/8 (INS)
42942 - 3/16 (STD)
42373 - 3/16 (STD) 42637 - 3/16 (WS 125) 42647 - 3/16 (RC) 42444 - 1/4 (STD)
3/4 19.1
42374 - 1/4 (STD) 42629 - 1/4 (WS 125) 42979 - 1/4 (HD, THK, RC) 43255 - 1/4 (WS 125)
42376 - 3/8 (STD) 42630 - 3/8 (WS 188) 43252 - 3/16 (HD, THK, RC) 42445 - 3/8 (STD)
7/8 22.2 42388 - 7/8 (STD) 42423 - 1/8 (STD)
42444 - 1/4 (STD)
1 25.4 42374 - 1/4 (STD) 42629 - 1/4 (WS 125) 42979 - 1/4 (HD, THK, RC) 42377 - 1/2 (STD)
43255 - 1/4 (WS 125)
42444 - 1/4 (STD)
1-1/2 38.1 42374 - 1/4 (STD) 42629 - 1/4 (WS 125) 42979 - 1/4 (HD, THK, RC) 42377 - 1/2 (STD) 42942 - 3/16 (STD)
43255 - 1/4 (WS 125)
42444 - 1/4 (STD)
1-3/4 44.5 42374 - 1/4 (STD) 42629 - 1/4 (WS 125) 42979 - 1/4 (HD, THK, RC) 42388 - 7/8 (STD)
43255 - 1/4 (WS 125)
42444 - 1/4 (STD)
2 50.8 42374 - 1/4 (STD) 42629 - 1/4 (WS 125) 42979 - 1/4 (HD, THK, RC) 42377 - 1/2 (STD)
43255 - 1/4 (WS 125)
Chart 3 * Use with straight crosscut knives for cut sizes up to 5/8".
Slicing Knife Holders, No Slots (no circular knives) Chart 4
Type of Knife Holder Insert Knife Slicing Knife Holders, Deep Crinkle, .300" slot spacing
Slice Part Number Part Number
Type Knife Holder Insert
42441 53178
Straight of Part Slot Knife
(grooved) 42650 Number Spacing Part Number
Slice
Crinkle, .076" 42443 53481
Deep Crinkle, .125" 42974 .300" 53561
Deep Crinkle, .125" 42671 53561
Deep Crinkle, .145" 42845 42847 Deep Crinkle, .145" 42846 .300" 42847
 10.44 Parts: Slicing Knives, one piece

Chart 1 - Knife Feature, Abbreviation and Description Restrictions

STD - Standard Do not use with .058" thick circular knives
2 The standard knife (straight and crinkle) is .312" thick (1), slots and feed discs (use with .038" thick parts).
(2) are .070" wide and clearance from the shear edge (3) to the Do not use crinkle crosscut knives with a
crosscut knives is .025" (.635 mm). In Chart 2, knife features are straight slicing knife.
3 standard unless otherwise indicated. For example, a knife listed as
1 WS125 (Wide Slot, .125") is standard thickness and clearance.

SC - Scalloped Do not use crinkle crosscut knives with a

Scalloped knife edge recommended for products with skin. scalloped slicing knife.

WS - Wide Slot Use with .058" thick circular knives and

Slots (4) are wider than .070"; slot width in decimal inches follows feed discs, and with products that cause
the abbreviation in Chart 2, for example WS125 indicates a slot knife deflection.
width of .125".
4
6 RC - Reduced Clearance Use with crosscut knife spindles with
Used to reduce the clearance between the crosscut knives (5) and narrow knives (sizes 3/32"–1/4") and
the shear edge (6) of the slicing knife to .012"–.015" (standard is heavy duty crosscut spindles only.
5 .025").

7 HD - Heavy Duty Slices will be .050"-.060" (1.27-1.52 mm)

The knife edge (7) is thicker and knife bevel more blunt than the thinner than the slice setting indicates.
standard knife. Standard bevel is 23°, heavy duty bevel is 30°.
HD25 - Heavy Duty 25°
The knife bevel is 25°, for dicing frozen products such as ham.
THK - Thick Slices will be .050"-.060" (1.27-1.52 mm)
This knife is .372" (9.45 mm) thick (8); standard knife is .312" thinner than the slice setting indicates.
(7.92 mm) thick. Do not use 42860 long slice guides (slice
10 guide mounts to the circular support
8 sides).
3HL - 3 Hole Requires the heavy duty slice case (3
Use with 43192 and 43193 Heavy Duty Slice Cases with 3 mounting holes for slicing knife).
mounting holes for the knife; one 42875 Flat Head Screw, 3/8-16 x
9 11/16", s.s., is used in the center hole (9).

BOW - Bowed None

Knife is bowed slightly to insure proper seating.

10 Long Slot May produce incomplete cuts when used

These knives have a single long slot (10). with circular knives; use with circular feed
42663 - Knife, slicing, straight, heavy duty, long slot assemblies (feed disc spindle).
43037 - Knife, slicing, straight, heavy duty, long slot, 3 hole

Blunt This knife has a blunt edge and is

This knife has a blunt edge; used for fracturing frozen product that intended for special applications.
would damage a sharpened edge; also has a long slot (see above).
42924 - Knife, slicing, straight, heavy duty, blunt

No Slots Cannot be used with circular knives.

For slice only or use with crosscut knife spindle; straight cut has
grooves (shown), crinkle knife is smooth; can be used with a feed
spindle.
42440 - Knife, slicing, straight, no slots
42442 - Knife, slicing, straight, no slots (.076" deep crinkle)
See Section 6 Machine Setup for additional information about slicing knife features.
 Parts: Slicing Knives, one piece 10.45

Item Quantity Part Knives

One piece Slicing Number and
withDescription
slots Example:
Chart 2 Part
Slot Feature
Part Number is followed by the slot spacing in inches and the following abbreviations.
Circular Number
Spacing Abbreviation
STD = Standard WS = Wide Slot , slot width, decimal inch BOW = Bowed (inch) (see previous page)
Knife and
HD = Heavy Duty SC = Scalloped THK = Thick
Feed Disc
Spacing
3HL = 3 Hole (requires HD slice case) RC = Reduced Clearance HD25 = 25° Bevel 42761 - 1/4 (HD, THK, RC)
All features are standard (STD) unless otherwise indicated.
inch mm Straight Cut Crinkle Cut .076"
42355 - 1/8 (STD) 42551 - 1/8 (RC) 42940 - 1/8 (HD, THK, RC)
1/8 3.2 ----
43099 - 1/8 (HD, THK, RC, SC) 43100 - 1/8 (HD, THK, RC, HD25)
42438 - 5/32 (STD) 42571 - 5/32 (HD) 42638 - 5/32 (HD, WS 093)
5/32 4.0 ----
43052 - 5/32 (SC, HD, THK, RC) 43239 - 5/32 (HD25)
42356 - 3/16 (STD) 42588 - 3/16 (HD) 42639 - 3/16 (HD, WS 125)
42787 - 3/16 (HD, THK, RC) 42953 - 3/16 (HD, BOW) 43056 - 3/16 (HD, RC, WS 110)
3/16 4.8 ----
43059 - 3/16 (SC, HD, THK, RC) 42941 - 3/16 (HD, 3HL) 42946 - 3/16 (HD, WS 125, 3HL)
43257 - 3/16 (HD25)
42355 - 1/8 (STD) 42551 - 1/8 (RC) 42940 - 1/8 (HD, THK, RC)
42357 - 1/4 (STD) 42532 - 1/4 (HD) 43099 - 1/8 (HD, THK, RC, SC)
1/4 6.4 42363 - 1/4 (STD)
42623 - 1/4 (HD, WS 125) 42761 - (HD, THK, RC) 43040 - 1/4 (SC, HD, THK, RC)
42869 - 1/4 (HD, WS 125, 3HL) 43048 - (RC, 3HL)
.300 7.6 42663 - (HD, Long Slot) 42924 - (HD, Blunt) ----
42438 - 5/32 (STD) 42571 - 5/32 (HD) 42638 - 5/32 (HD, WS 093)
5/16 7.9 42358 - 5/16 (STD) 42746 - 5/16 (HD, WS 188) 43052 - 5/32 (SC, HD, THK, RC) ----
42841 - 5/16 (HD, THK, RC, WS 110) 42874 - 5/16 (HD, WS 188, 3HL) 43305 - 5/16 (HD, THK, RC)
42355 - 1/8 (STD) 42551 - 1/8 (RC) 42940 - 1/8 (HD, THK, RC)
42356 - 3/16 (STD) 42588 - 3/16 (HD) 43099 - 1/8 (HD, THK, RC, SC)
42639 - 3/16 (HD, WS 125) 42787 - 3/16 (HD, THK, RC) 42953 - 3/16 (HD, BOW)
3/8 9.5 42364 - 3/8 (STD)
43056 - 3/16 (HD, RC) 43059 - 3/16 (SC, HD, THK, RC) 42359 - 3/8 (STD)
42533 - 3/8 (HD) 42624 - 3/8 (HD, WS 188) 43041 - 3/8 (SC, HD, THK, RC)
42871 - 3/8 (HD, WS 188, 3HL) 43263 - 3/8 (HD, WS 110, THK, RC)
42355 - 1/8 (STD) 42551 - 1/8 (RC) 42940 - 1/8 (HD, THK, RC)
42357 - 1/4 (STD) 42532 - 1/4 (HD) 43099 - 1/8 (HD, THK, RC, SC)
1/2 12.7 42623 - 1/4 (HD, WS 125) 42761 - 1/4 (HD, THK, RC) 43040 - 1/4 (SC, HD, THK, RC) 42363 - 1/4 (STD)
42869 - 1/4 (HD, WS 125, 3HL) 43048 - 1/4 (RC, 3HL) 42360 - 1/2 (STD)
42657 - 1/2 (HD, WS 250) 42870 - 1/2 (HD, WS 250, 3HL) 10
42355 - 1/8 (STD) 42551 - 1/8 (RC) 42940 - 1/8 (HD, THK, RC)
43099 - 1/8 (HD, THK, RC, SC) 42358 - 5/16 (STD) 42746 - 5/16 (HD, WS 188)
5/8 15.9 ----
42841 - 5/16 (HD, THK, RC) 43305 - 5/16 (HD, THK, RC) 42361 - 5/8 (STD)
42652 - 5/8 (HD, WS 250) 42877 - 5/8 (HD, WS 125, 3HL) 42872 - 5/8 (HD, WS 250, 3HL)
42355 - 1/8 (STD) 42551 - 1/8 (RC) 42940 - 1/8 (HD, THK, RC)
42356 - 3/16 (STD) 42588 - 3/16 (HD) 43099 - 1/8 (HD, THK, RC, SC)
42639 - 3/16 (HD, WS 125) 42787 - 3/16 (HD, THK, RC) 42953 - 3/16 (HD, BOW)
43056 - 3/16 (HD, RC) 43059 - 3/16 (SC, HD, THK, RC) 42532 - 1/4 (HD)
42363 - 1/4 (STD)
3/4 19.1 42357 - 1/4 (STD) 42623 - 1/4 (HD, WS 125) 42761 - 1/4 (HD, THK, RC)
42364 - 3/8 (STD)
42359 - 3/8 (STD) 42533 - 3/8 (HD) 43040 - 1/4 (SC, HD, THK, RC)
42653 - 3/4 (HD, WS 250) 42624 - 3/8 (HD, WS 188) 43041 - 3/8 (SC, HD, THK, RC)
42869 - 1/4 (HD, WS 125, 3HL) 43048 - 1/4 (RC, 3HL) 42871 - 3/8 (HD, WS 188, 3HL)
43263 - 3/8 (HD, WS 110, THK, RC)
7/8 22.2 42391 - 7/8 (STD) 42355 - 1/8 (STD) 43307 - 7/8 (HD, WS 125, 3HL) ----
42357 - 1/4 (STD) 42532 - 1/4 (HD) 42623 - 1/4 (HD, WS 125)
42761 - 1/4 (HD, THK, RC) 43040 - 1/4 (SC, HD, THK, RC) 42360 - 1/2 (STD)
1 25.4 42363 - 1/4 (STD)
42657 - 1/2 (HD, WS 250) 42869 - 1/4 (HD, WS 125, 3HL) 43048 - 1/4 (RC, 3HL)
42870 - 1/2 (HD, WS 250, 3HL)
42357 - 1/4 (STD) 42532 - 1/4 (HD) 42623 - 1/4 (HD, WS 125)
42761 - 1/4 (HD, THK, RC) 43040 - 1/4 (SC, HD, THK, RC) 42360 - 1/2 (STD)
1-1/2 38.1 42363 - 1/4 (STD)
42657 - 1/2 (HD, WS 250) 42653 - 3/4 (HD, WS 250) 42869 - 1/4 (HD, WS 125, 3HL)
43048 - 1/4 (RC, 3HL) 42870 - 1/2 (HD, WS 250, 3HL)
42357 - 1/4 (STD) 42532 - 1/4 (HD) 42623 - 1/4 (HD, WS 125)
1-3/4 44.5 42391 - 7/8 (STD) 42761 - 1/4 (HD, THK, RC) 43040 - 1/4 (SC, HD, THK, RC) 42363 - 1/4 (STD)
42869 - 1/4 (HD, WS 125, 3HL) 43048 - 1/4 (RC, 3HL)
42357 - 1/4 (STD) 42532 - 1/4 (HD) 42623 - 1/4 (HD, WS 125)
42761 - 1/4 (HD, THK, RC) 43040 - 1/4 (SC, HD, THK, RC) 42360 - 1/2 (STD)
2 50.8 42363 - 1/4 (STD)
42657 - 1/2 (HD, WS 250) 43048 - 1/4 (RC, 3HL) 42869 - 1/4 (HD, WS 125, 3HL)
42870 - 1/2 (HD, WS 250, 3HL) 43037 - (HD, Long Slot, 3HL)
 10.46 Parts: Circular Knife Spindle Assemblies, .038" thick knives,
1.4" diameter spacers

10
 Parts: Circular Knife Spindle Assemblies, .038" thick knives, 10.47
1.4" diameter spacers
Item Quantity Part Number and Description
1 1 * - Spindle Assembly, circular (includes items 2–7)
2 1 42806 - Shaft, circular knife, hard, .038" knife, ACME thread
3 2 42489 - O-ring, 1/16" x 7/8" x 1", Viton
4 * 42265 - Knife, circular, 3.5", serrated, double bevel, .038" thick
5 * * - Spacer, 1.4" O.D., .038" thick knife
6 1 * - Spacer, 1.4" O.D., .038" thick knife (some assemblies require a final spacer;
see chart below)
7 1 42264 - Nut, circular shaft, ACME

Alternate parts
8 1 43038 - Shaft, circular knife, 17-4, .038" knife, ACME thread
9 1 43076 - Shaft, circular knife, 17-4, .038" knife, fine thread
1 43839 - Shaft, circular knife, hard, .038" knife, fine thread
10 1 42820 - Nut, circular shaft, large O.D., fine thread (for heavy duty applications; do not exceed
1/2" slice thickness; do not use with a secondary stripper plate)
11 1 43098 - Nut, circular shaft, fine thread (requires a 36 mm open end wrench,
part number 98290)
12 42490 - Knife, circular, 3.5", double bevel, .038" thick (plain edge, no serrations)
13 42555 - Knife, circular, 3.5", serrated, double bevel, heavy duty, .038" (thicker at the knife edge
than the standard knife; see dimension “D” on the opposite page)
14 43101 - Knife, circular, 3.5", serrated, single bevel, heavy duty, .038" (for compressible
products such as greens)
15 42649 - Spacer, filler, .038" thick, 1.40" O.D. (use in place of knives to change the size of cut)

* See chart below.

Circular Knife Spindle Assemblies,

.038" thick knives, 1.40" diameter spacers
Circular Item 4 Item 6
Item 5
Size of Cut Knife Spindle 42265 Knife, Final
Assembly .038" thick Spacer, 1.4" O.D. Spacer
Part
inch mm Part Number Quantity Number Quantity Quantity: 1
1/8 3.2 42428 85 42319 84 – 10
.150 3.8 42948 71 42947 70 –
5/32 4.0 42437 68 42402 67 –
3/16 4.8 42429 57 42320 56 –
7/32 5.6 – 49 43230 48 –
1/4 6.4 42430 43 42321 42 –
9/32 7.1 42646 38 42644 36 42323
.290 7.4 42766 37 42762 35 42765
19/64 7.5 42592 36 42589 34 42838
5/16 7.9 42431 34 42322 32 42324
11/32 8.7 42804 31 42802 29 42803
3/8 9.5 42432 29 42323 28 –
7/16 11.1 42632 25 42633 24 –
1/2 12.7 42433 22 42324 21 –
9/16 14.2 43312 20 42821 18 42323
5/8 15.9 42434 18 42325 16 42324
3/4 19.1 42435 15 42326 14 –
7/8 22.2 42481 13 42482 12 –
1/ 25.4 42436 12 42327 10 42324
1-1/2 38.1 42561 8 42560 7 –
1-3/4 44.5 42484 7 42485 6 –
 10.48 Parts: Circular Knife Spindles with Large Diameter Spacers,
.038" thick knives

10

Item Quantity Part Number and Description

1 1 * - Spindle Assembly, circular (includes items 2–7)
2 1 42806 - Shaft, circular knife, hard, .038" knife, ACME thread
3 2 42489 - O-ring, 1/16" x 7/8" x 1", Viton
4 * 42265 - Knife, circular, 3.5", serrated, double bevel, .038" thick
5 * * - Spacer, large diameter, .038" thick knife
6 1 * - Spacer, large diameter, .038" thick knife (some assemblies require a final spacer;
see Chart 1)
7 1 42264 - Nut, circular shaft, ACME

* See charts on the next page.

See Circular Knife Spindle Assemblies, .038" thick knives, 1.4" diameter spacers for alternate shafts, nuts and
knives.

Alternate parts
8 43235 - Spacer, filler, .038" thick, 1.80" O.D. (use in place of knives to change the size of cut)
9 43236 - Spacer, filler, .038" thick, 2.08" O.D. (use in place of knives to change the size of cut)
 Parts: Circular Knife Spindles with Large Diameter Spacers, 10.49
.038" thick knives
Ordering a spindle with Alternate Parts
Spindles with large diameter spacers do not have assembly numbers. Follow these steps when ordering:
1. See the column titled “Reference Spindle Assembly” in Chart 1, and select the appropriate knife and/or feed
disc spacing. The Reference Spindle Assembly contains all knives (42265) and 1.40" diameter spacers.
2. Choose corresponding large diameter spacers.
3. Substitute large diameter spacers into the reference assembly.

Restrictions for Large Diameter Spacers

Slice Opening: the slice opening is restricted, see Chart 2
Stripper Plates: do not use stripper plate shims; do not use secondary stripper plates.
Feed Discs: the points on discs with small diameters will not protrude beyond the stripper plate.

Chart 1 Chart 2
Reference Assemblies and large diameter spacers, Maximum slice opening with large
.038" thick knives diameter circular knife spacers
Space between Reference Item 4 Items 5 and 6 Circular Knife Stripper Maximum
Knives or Feed Spindle Knife, Large Diameter Spacers Spacer Plate Spacer Slice Opening
Discs Assembly .038" thick Diameter (D) (S) (M)
inch mm Part Number Quantity Part No. Diameter Quantity Part Number inch mm
Standard Stripper Plate**
1/8 3.2 42428 85 42603 2.08 84
5/32 4.0 42437 68 42604 2.08 67
3/16 4.8 42429 57 42605 2.08 56
42606 2.08 42
1/4 6.4 42430 43
42976 1.80 42
42643 2.08 36
9/32 7.1 42646 38
42977 2.08 1
42665 1.80 32
42609 1.80 1 42394 1/4 6.4
5/16 7.9 42431 34
42607 2.08 32 1.80" 42393 1/2 12.7 10
42392 1/2 12.7
42978 2.08 1
42394 3/16 4.8
42608 1.80 28 2.08"
3/8 9.5 42432 29 42393 5/16 7.9
42977 2.08 28 Relieved Stripper Plate*
7/16 11.1 42632 25 42660 1.80 24
42609 1.80 21
1/2 12.7 42433 22
42978 2.08 21

42394 1/4 6.4

1.80" 42393 3/8 9.5
42392 1/2 12.7
42394 1/4 6.4
2.08" 42393 1/4 6.4
42392 5/16 7.9
** See Stripper Plates and Stripper Plate
Spacers and Shims.
 10.50 Parts: Circular Knife Spindles with Feed Discs, .038" thick knives

10

Item Quantity Part Number and Description

1 1 * - Spindle Assembly, circular, with feed discs (includes items 2–7)
2 1 42806 - Shaft, circular knife, hard, .038" knife, ACME thread
3 2 42489 - O-ring, 1/16" x 7/8" x 1", Viton
4 * 42265 - Knife, circular, 3.5", serrated, double bevel, .038" thick
5 * * - Feed Disc, .038" thick (see “Feed Discs, .038" thick” on the following pages)
6 * * - Spacer, 1.4" O.D., .038" thick knife
7 1 42264 - Nut, circular shaft, ACME

* See charts on the next page.

See Circular Knife Spindle Assemblies, .038" thick knives, 1.4" diameter spacers for alternate shafts, nuts and
knives.
 Parts: Circular Knife Spindles with Feed Discs, .038" thick knives 10.51

Chart 1 Circular spindle assemblies with knives and feed discs, .038" thick
Item 1 Item 6
Item 4
Size of Circular Knife Item 5 Spacer, 1.4" O.D.
42265 Knife
Cut Spindle Feed Disc
.038" thick
Assembly Size
inch mm Part Number Quantity Part Number Quantity Part Number inch mm Quantity

3/4 19.1 42543 15 42527 14 42323 3/8 9.5 28

2 50.8 42544 6 42507 37 42321 1/4 6.4 42

Ordering a spindle with Alternate Parts

Spindles with knife and feed disc combinations do not have assembly numbers with the exception of the
assemblies in Chart 1. To order a spindle with a customized set of knives, feed discs and spacers, follow these
steps when ordering:
1. See the column titled “Reference Spindle Assembly” in Chart 2, and select the appropriate knife and feed disc
spacing. The Reference Spindle Assembly contains all knives (42265) and 1.40" diameter spacers.
2. Choose knives, feed discs and spacers from the previous and following pages.
3. Substitute parts into the reference assembly.

Restrictions apply to some parts; see the instructions on the corresponding pages.

Chart 2 Reference Assemblies for Spindles with

Knives and Feed Discs, .038" thick
Space Between Item 4 Knife Item 6
Knives Reference and Spacer*
and Spindle Item 5 Feed Disc, (final spacer required
Feed Discs Assembly .038" thick on some spindles)
inch mm Part Number Total Quantity Quantity Final Spacer
1/8 3.2 42428 85 84 –
.150 3.8 42948 71 70 –
5/32 4.0 42437 68 67 – 10
3/16 4.8 42429 57 56 –
7/32 5.6 – 49 48 –
1/4 6.4 42430 43 42 –
9/32 7.1 42646 38 36 1
.290 7.4 42766 37 35 1
19/64 7.5 42592 36 34 1
5/16 7.9 42431 34 32 1
11/32 8.7 42804 31 29 1
3/8 9.5 42432 29 28 –
7/16 11.1 42632 25 24 –
1/2 12.7 42433 22 21 –
5/8 15.9 42434 18 16 1
3/4 19.1 42435 15 14 –
7/8 22.2 42481 13 12 –
1 25.4 42436 12 10 1
1-1/2 38.1 42561 8 7 –
1-3/4 44.5 42484 7 6 –
* 1.40" diameter spacers are standard on the reference spindle assembly.
Spindles can also be assembled with 1.80" and 2.08" diameter spacers.
 10.52 Parts: Feed Spindle Assemblies, .038" thick feed discs

10
Item Quantity Part Number and Description
1 1 * - Spindle Assembly, feed (includes items 2–7)
2 1 42806 - Shaft, circular knife, hard, .038" knife, ACME thread
3 2 42489 - O-ring, 1/16" x 7/8" x 1", Viton
4 * * - Feed Disc, .038" thick (see “Feed Discs, .038" thick” on the following pages)
5 * * - Spacer, .038" thick knife
6 1 * - Spacer, .038" thick knife (some assemblies require a final spacer; see Chart 2)
7 1 42264 - Nut, circular shaft, ACME

Alternate parts
8 1 43038 - Shaft, circular knife, 17-4, .038" knife, ACME thread
9 1 43076 - Shaft, circular knife, 17-4, .038" knife, fine thread
1 42839 - Shaft, circular knife, hard, .038" knife, fine thread
10 1 42820 - Nut, circular shaft, large O.D., fine thread (do not exceed 1/2" slice thickness
– 1 43098 - Nut, circular shaft, fine thread (not shown; requires a 36 mm open end wrench,
part number 98290)
11 * - Spacer, large diameter (see Chart 3 for important restrictions)
12 42844 - Knife Disc, 3.5" (used to produce a torn appearance)

* See charts on the next page.

 Parts: Feed Spindle Assemblies, .038" thick feed discs 10.53

Chart 1 Feed Spindle Assembly, .038" thick feed discs

Item 4 Item 5 .300"
Space Between Spindle
Feed Disc, Spacer, 1.4" O.D.
Feed Discs Assembly
.038" thick Part
inch mm Part Number Quantity Number Quantity
.300 7.6 42545* 36 (42528) 42525 35
*For producing crinkle cut French fries; slice thickness is set at .344" (8.7 mm);
feed discs are spaced .300" (7.6 mm) apart to contact the bottom of the crinkle.
Ordering a feed spindle
Feed spindles do not have assembly numbers (except for .300" spindle in Chart 1). Follow these steps when
ordering a customized feed spindle:
1. See the column titled “Reference Spindle Assembly” in Chart 2, and select the appropriate feed disc spacing.
The Reference Spindle Assembly contains all knives (42265) and 1.40" diameter spacers.
2. See “Feed Discs, .038" thick” on the following pages and choose a feed disc with the appropriate diameter.
Also choose the spacer with the appropriate diameter from Chart 2.
3. Substitute feed discs and spacers into the reference assembly.

Restrictions for Large Diameter Spacers

Slice Opening: the slice opening is restricted, see Chart 3
Stripper Plates: do not use stripper plate shims; do not use secondary stripper plates.
Feed Discs: the points on discs with small diameters will not protrude beyond the stripper plate.
Chart 2 Chart 3
Reference Assemblies for Feed Spindles, .038" thick feed discs Maximum slice opening with large
Space Reference Item 4 Items 5 and 6 Item 11Large Diameter diameter spacers
Between Feed Spindle Feed Spacer, 1/4" O.D. Spacers (optional) Circular Knife Stripper Maximum
Discs Assembly Disc Part (substitute for items 5 and 6) Spacer Plate Spacer Slice Opening
inch mm Part Number Quantity Number Quantity Part No. Diameter Quantity Diameter (D) (S) (M)
1/8 3.2 42428 85 42319 84 42603 2.08 84 Part Number inch mm
.150 3.8 42948 71 42947 70 – – – Standard Stripper Plate*
5/32 4.0 42437 68 42402 67 42604 2.08 67
3/16 4.8 42429 57 42320 56 42605 2.08 56
7/32 5.6 – 49 43230 49 – – –
1/4 6.4 42430 43 42321 42 42606 2.08 42 10
42644 36 42643 2.08 36
9/32 7.1 42646 38
42323 1 42977 2.08 1
42762 35 – – –
.290 7.4 42766 37
42765 1 – – –
42589 34 – – –
19/64 7.5 42592 36
42838 1 – – –
42665 1.80 32 42394 1/4 6.4
42322 32 42609 1.80 1 1.80" 42393 1/2 12.7
5/16 7.9 42431 34
42324 1 42607 2.08 32 42392 1/2 12.7
42978 2.08 1
42394 3/16 4.8
42802 29 – – – 2.08"
11/32 8.7 42804 31 42393 5/16 7.9
42803 1 – – –
Relieved Stripper Plate*
42608 1.80 28
3/8 9.5 42432 29 42323 28 42394 1/4 6.4
42977 2.08 28
7/16 11.1 42632 25 42633 24 42660 1.80 24 1.80" 42393 3/8 9.5
42609 1.80 21 42392 1/2 12.7
1/2 12.7 42433 22 42324 21
42978 2.08 21 42394 1/4 6.4
42325 16 – – – 2.08" 42393 1/4 6.4
5/8 15.9 42434 18
42324 1 – – –
42392 5/16 7.9
3/4 19.1 42435 15 42326 14 – – –
7/8 22.2 42481 13 42482 12 – – – * See Stripper Plates and Stripper Plate
42327 10 – – – Spacers and Shims.
1 25.4 42436 12
42324 1 – – –
1-1/2 38.1 42561 8 42560 7 – – –
1-3/4 44.5 42484 7 42485 6 – – –
 10.54 Parts: Feed Discs, .038" thick

6 Point 12 Point 26 Point 28 Point

20 Point

10
 Parts: Feed Discs, .038" thick 10.55

Selecting Feed Discs

Dimension (D) in the chart below is the minimum penetration
into the product for a given slice thickness and feed disc.
Discs with larger diameters (B) can be used for increased
penetration. To calculate penetration into the product for a
disc, take the slice thickness (A) you wish to cut and subtract
Distance from Slicing Knife (C) for that disc.
For example:

.50" (slice thickness)

– .40" (dimension “C” for disc 42349)
.10" (penetration into product)

12.7 mm (slice thickness)

– 10.2 mm (dimension “C” for disc 42349)
2.5 mm (penetration into product)

Chart 1

(A) Feed Disc, .038" thick (D)

Slice Thickness (C) Minimum
(B) Number Penetration
Item Part Distance from
inch mm Diameter of
Number Number Slicing Knife into product
Points
fraction decimal – inch mm inch mm inch mm
3/32 .09 2.3 1 42612 3.33 84.6 .05 1.1 28 .04 1.0 10
1/8 .13 3.2 2 42507 3.24 82.3 .09 2.3 6 .04 1.0
5/32 .16 4.0 3 42969 3.15 80.0 .14 3.5 28 .02 .5
3/16 .19 4.8 4 42351 3.10 78.7 .16 4.1 6 .03 .8
7/32 .22 5.6 5 42530 3.04 77.2 .19 4.8 28 .03 .8
1/4 .25 6.4 6 42570 2.98 75.5 .22 5.6 12 .03 .8
.29 7.4 .02 .5
.30 7.5 7 42529 2.88 73.2 .27 6.9 26 .03 .8
5/16 .31 7.9 .05 1.3
5/16 .31 7.9 8 42578 2.86 72.6 .28 7.1 12 .03 .8
11/32 .34 8.7 9 42528 2.80 71.1 .31 7.9 26 .04 1.0
3/8 .38 9.5 10 42350 2.74 69.6 .34 8.6 6 .04 1.0
3/8 .38 9.5 11 42776 2.72 69.1 .35 8.9 12 .03 .8
7/16 .44 11.1 12 42349 2.62 66.5 .40 10.2 6 .04 1.0
1/2 .50 12.7 13 42293 2.49 63.2 .46 11.7 6 .04 1.0
9/16 .56 14.2 14 42775 2.40 61.0 .51 13.0 12 .05 1.3
5/8 .63 15.9 15 42648 2.24 56.9 .59 15.0 6 .04 1.0
11/16 .69 17.5 16 42732 2.21 56.1 .62 15.7 12 .07 1.8
3/4 .75 19.1 17 42527 2.00 50.8 .71 18.0 20 .04 1.0
 10.56 Parts: Circular Knife Spindle Assemblies, .058" thick knives,
1.4" diameter spacers

10

IMPORTANT
When assembling the spindle, alternate the flat area (A) on the
inside diameter of the knives from side-to-side on the shaft. The shaft
for .058" thick knives has flats (B) on opposite sides. Assemble the
spindle in this manner to ensure that knives align with the slots in the
stripper plate.
 Parts: Circular Knife Spindle Assemblies, .058" thick knives, 10.57
1.4" diameter spacers
Item Quantity Part Number and Description
1 1 * - Spindle Assembly, circular, .058" Knife (includes items 2–7)
2 1 42807 - Shaft, circular knife, hard, .058" knife, ACME
3 2 42489 - O-ring, 1/16" x 7/8" x 1", Viton
4 * 42661 - Knife, circular, 3.5", plain, double bevel, .058" thick
5 * * - Spacer, 1.4" O.D., .058" thick knife
6 1 * - Spacer, 1.4" O.D., .058" thick knife (some assemblies require a final spacer;
see Chart 1)
7 1 42264 - Nut, circular shaft, ACME

Alternate parts
8 1 43039 - Shaft, circular knife, 17-4, .058" Knife, ACME
9 1 43077 - Shaft, circular knife, 17-4, .058" Knife, fine thread
1 42819 - Shaft, circular knife, hard, .058" Knife, fine thread
10 1 42820 - Nut, circular shaft, large O.D., fine thread (do not exceed 1/2" slice thickness)
11 1 43098 - Nut, circular shaft, fine thread (requires a 36 mm open end wrench,
part number 98290)
12 42759 - Knife, circular, 3.5", serrated, double bevel, .058" thick
13 43259 - Knife, circular, 3.5", serrated, double bevel, .058" thick (17-4 version of 42759;
harder and more durable, used for tougher applications)
14 42773 - Spacer, filler, .058" thick, 1.40" O.D. (use in place of knives to change the size of cut)
– ** - Feed Disc, .058" thick

* See chart below.

** Circular spindles can be assembled with a combination of knives and feed discs. These spindles do not
have part numbers. See the following pages for feed discs and ordering information.

Chart 1 Circular Knife Spindle Assemblies,

.058" thick knives, 1.40" diameter spacers
Circular Item 4 Item 6
42265 Knife, Item 5
Size of Cut Knife Spindle Final
Assembly .038" thick Spacer, 1.4" O.D. Spacer
inch mm Part Number Quantity Part Number Quantity Quantity: 1

1/8 3.2 § 85 42723 84 –

1/4 6.4 42706 43 42684 42 – 10
9/32 7.1 42707 38 42685 36 42687
5/16 7.9 42708 34 42686 32 42689
3/8 9.5 42709 29 42687 28 –
7/16 11.1 42710 25 42688 24 –
1/2 12.7 42711 22 42689 21 –
§§
9/16 14.2 42834 20 42832 18 42687
19/32 15.1 42829 19§§ 42828 17 42831
5/8 15.9 42712 18 42690 16 42689
3/4 19.1 42713 15 42691 14 –
7/8 22.2 42714 13 42692 12 –
1/ 25.4 42715 12 42693 10 42689
1-1/2 38.1 42716 8 42694 7 –
1-3/4 44.5 42717 7 42695 6 –
§
Slight variations in knife and spacer thickness combined with the large number of knives and spacers may prevent the
knives from properly aligning with the slots in the stripper plate. Consult an Urschel representative for additional information
on the use of these parts.
§§
These assemblies use circular knife 42759.
 10.58 Parts: Circular Knife Spindles with Large Diameter Spacers,
.058" thick knives

10

Item Quantity Part Number and Description

1 1 * - Spindle Assembly, circular, .058" knife (includes items 2–7)
2 1 42807 - Shaft, circular knife, hard, .058 knife, ACME
3 2 42489 - O-ring, 1/16" x 7/8" x 1", Viton
4 * 42661 - Knife, circular, 3.5", plain, double bevel, .058" thick
5 * * - Spacer, .058" thick knife
6 1 * - Spacer, .058" thick knife (some assemblies require a final spacer; see Chart 1)
7 1 42264 - Nut, circular shaft, ACME

* See charts on the next page.

See Circular Knife Spindle Assemblies, .058" thick knives, 1.4" diameter spacers for alternate shafts, nuts and
knives.

Alternate parts
8 43233 - Spacer, filler, .058" thick, 1.80" O.D. (use in place of knives to change the size of cut)
9 43234 - Spacer, filler, .058" thick, 2.08" O.D. (use in place of knives to change the size of cut)
 Parts: Circular Knife Spindles with Large Diameter Spacers, 10.59
.058" thick knives
Restrictions for Large Diameter Spacers
Slice Opening: the slice opening is restricted, see Chart 2
Stripper Plates: do not use stripper plate shims; do not use secondary stripper plates.
Feed Discs: the points on discs with small diameters will not protrude beyond the stripper plate (see
“Feed Spindle Assemblies, .058" thick feed discs” on the following pages).

Chart 1 Chart 2
Circular Knife Spindle Assemblies with Maximum slice opening with large
Large Diameter Spacers, .058" thick knives diameter circular knife spacers
Size Circular Item 4 Item 5 Item 6 Circular Knife Stripper Maximum
Spacer Spacer Plate Spacer Slice Opening
of Cut Knife Spindle 42261 Knife Final
Diameter (D) (S) (M)
Assembly .058" thick Part Quantity Diameter Spacer
Part Number inch mm
inch mm Part Number Quantity Number (inch) Quantity: 1
Standard Stripper Plate*
1/8 3.2 * 85 42724 84 2.08 –
3/16 4.8 42235 57 42767 56 2.08 –
– 43 42930 42 1.80 –
1/4 6.4
42718 43 42696 42 2.08 –
9/32 7.1 42719 38 42697 36 2.08 42837
5/16 7.9 42720 34 42698 32 2.08 42725
3/8 9.5 42721 29 42699 28 1.80 –
42722 22 42700 21 1.80 – 42394 1/4 6.4
1/2 12.7
– 22 42725 21 2.08 – 1.80" 42393 1/2 12.7
3/4 19.1 – 15 43078 14 1.80 – 42392 1/2 12.7
* Slight variations in knife and spacer thickness combined with the large 42394 3/16 4.8
2.08"
number of knives and spacers may prevent the knives from properly aligning 42393 5/16 7.9
with the slots in the stripper plate. Consult an Urschel representative for Relieved Stripper Plate*
additional information.

10

42394 1/4 6.4

1.80" 42393 3/8 9.5
42392 1/2 12.7
42394 1/4 6.4
2.08" 42393 1/4 6.4
42392 5/16 7.9
* See Stripper Plates and Stripper Plate
Spacers and Shims.
 10.60 Parts: Feed Spindle Assemblies, .058" thick feed discs

10

Item Quantity Part Number and Description

1 1 * - Spindle Assembly, feed (includes items 2–7)
2 1 42807 - Shaft, circular knife, hard, .058" knife, ACME thread
3 2 42489 - O-ring, 1/16" x 7/8" x 1", Viton
4 * * - Feed Disc, .058" thick (see “Feed Discs, .058" thick” on the following pages)
5 * * - Spacer, .058" thick knife
6 1 * - Spacer, .058" thick knife (some assemblies require a final spacer; see Chart 1)
7 1 42264 - Nut, circular shaft, ACME

Alternate parts
8 1 43039 - Shaft, circular knife, 17-4, .058" Knife, ACME
9 1 43077 - Shaft, circular knife, 17-4, .058" Knife, fine thread
1 42819 - Shaft, circular knife, hard, .058" Knife, fine thread
10 1 42820 - Nut, circular shaft, large O.D., fine thread (do not exceed 1/2" slice thickness)
1 43098 - Nut, circular shaft, fine thread (requires a 36 mm open end wrench,
part number 98290)

* See charts on the next page.

 Parts: Feed Spindle Assemblies, .058" thick feed discs 10.61

Ordering a feed spindle

Feed spindles do not have assembly numbers. Follow these steps when ordering:
1. See the column titled “Reference Spindle Assembly” in Chart 1, and select the appropriate feed disc spacing
and spacer diameter. The Reference Spindle Assembly contains all knives (42261).
2. See “Feed Discs, .058" thick” on the following pages and choose a feed disc with the appropriate diameter.
3. Substitute feed discs and spacers into the reference assembly.

Restrictions for Large Diameter Spacers

Slice Opening: the slice opening is restricted, see Chart 2
Stripper Plates: do not use stripper plate shims; do not use secondary stripper plates.
Feed Discs: the points on discs with small diameters will not protrude beyond the stripper plate.

Chart 1 Chart 2
Reference Assemblies for Feed Spindles, .058" thick feed discs Maximum slice opening with large
Space Between Reference diameter spacers
Item 5 Item 6
Feed Discs Spindle Item 4 Circular Knife Stripper Maximum
Spacer Final
Assembly Feed Disc Spacer
Spacer Plate Spacer Slice Opening
Part Quantity Diameter
inch mm Part Number Quantity Quantity: 1 Diameter (D) (S) (M)
Number (inch)
Part Number inch mm
* 85 42723 – 1.40 –
1/8 3.2 Standard Stripper Plate
* 85 42724 – 2.08 –
3/16 4.8 42235 57 42767 56 2.08 –
42706 43 42684 42 1.40 –
1/4 6.4 – 43 42930 42 1.80 –
42718 43 42696 42 2.08 –
42707 38 42685 36 1.40 42687
9/32 7.1
42719 38 42697 36 2.08 42837
42708 34 42686 32 1.40 42689
5/16 7.9
42720 34 42698 32 2.08 42725 42394 1/4 6.4
42709 29 42687 28 1.40 – 1.80" 42393 1/2 12.7
3/8 9.5
42721 29 42699 28 1.80 – 42392 1/2 12.7 10
7/16 11.1 42710 25 42688 24 1.40 – 42394 3/16 4.8
2.08"
42711 22 42689 21 1.40 – 42393 5/16 7.9
Relieved Stripper Plate
1/2 12.7 42722 22 42700 21 1.80 –
42394 1/4 6.4
– 22 42725 21 2.08 –
1.80" 42393 3/8 9.5
9/16 14.3 42834 20 42832 18 1.40 42687 42392 1/2 12.7
19/32 15.1 42829 19 42828 17 1.40 42831 42394 1/4 6.4
5/8 15.9 42712 18 42690 16 1.40 42689 2.08" 42393 1/4 6.4
42713 15 42691 14 1.40 – 42392 5/16 7.9
3/4 19.1
– 15 43078 14 1.80 –
7/8 22.2 42714 13 42692 12 1.40 –
1 25.4 42715 12 42693 10 1.40 42689
1-1/2 38.1 42716 8 42694 7 1.40 –
1-3/4 44.5 42717 7 42695 6 1.40 –
* Slight variations in disc and spacer thickness combined with the large number
of discs and spacers may prevent the discs from properly aligning with the slots
in the stripper plate. Consult an Urschel representative for additional information.
 10.62 Parts: Feed Discs, .058" thick

6 Point 9 Point 20 Point 28 Point

26 Point

12 Point

10
 Parts: Feed Discs, .058" thick 10.63

Selecting Feed Discs

Dimension (D) in the chart below is the minimum penetration
into the product for a given slice thickness and feed disc.
Discs with larger diameters (B) can be used for increased
penetration. To calculate penetration into the product for a
disc, take the slice thickness (A) you wish to cut and subtract
Distance from Slicing Knife (C) for that disc.
For example:

.50" (slice thickness)

– .40" (dimension “C” for disc 42736)
.10" (penetration into product)

12.7 mm (slice thickness)

– 10.2 mm (dimension “C” for disc 42736)
2.5 mm (penetration into product)

Chart 1

(A) Feed Disc, .058" thick (D)

Slice Thickness (C) Minimum
(B) Number Penetration
Item Part Distance from
inch Diameter of
Number Number Slicing Knife into product
fraction decimal mm Points inch mm
inch mm inch mm
For granulating 1 43061 3.54 89.9 – – 28 – –
3/32 .09 2.3 2 42741 3.33 84.6 .05 1.1 28 .04 1.0 10
3 42740 3.24 82.3 .09 2.3 6 .04 1.0
1/8 .13 3.2
4 43054 3.24 82.3 .09 2.3 9 .04 1.0
3/16 .19 4.8 5 42866 3.10 78.7 .16 4.1 6 .03 .8
1/4 .25 6.4 6 42854 2.98 75.5 .22 5.6 12 .03 .8
.29 7.4 .02 .5
.30 7.5 7 42731 2.88 73.2 .27 6.9 26 .03 .8
5/16 .31 7.9 .05 1.3
5/16 .31 7.9 8 42730 2.86 72.6 .28 7.1 12 .03 .8
11/32 .34 8.7 9 42738 2.80 71.1 .31 7.9 26 .04 1.0
3/8 .38 9.5 10 42737 2.74 69.6 .34 8.6 6 .04 1.0
7/16 .44 11.1 11 42736 2.62 66.5 .40 10.2 6 .04 1.0
1/2 .50 12.7 12 42735 2.49 63.2 .46 11.7 6 .04 1.0
5/8 .63 15.9 13 42734 2.24 56.9 .59 15.0 6 .04 1.0
5/8 .63 15.9 14 42733 2.21 56.1 .61 15.5 12 .02 .5
3/4 .75 19.1 15 42743 2.00 50.8 .71 18.0 20 .04 1.0
 10.64 Parts: Stripper Plates

See chart 1 below for stripper plate features and restrictions.

Chart 2 on the next page lists stripper plates for use at different circular knife or feed disc spacing.
The following pages show stripper plates and spacers used at different slice settings.
See Section 6 Machine Setup for a description of stripper plates and application information.

Chart 1
Abbreviations and Descriptions Restrictions
STD - Standard Profile Maximum slice opening is 3/4" (19.1 mm)
The standard stripper plate has the profile shown at the with 1.4" diameter circular spacers.
Other restrictions apply when using large diameter
left. The slots are .085" (2.2 mm) wide unless otherwise
circular spacers. See charts on the following pages.
indicated.

R - Relieved Profile Maximum slice opening is 1/2" (12.7 mm)

This stripper plate has slots that are relieved (1), or with 1.4" diameter circular spacers.
Other restrictions apply when using large diameter
1 partially cut through, to the trailing edge. The slots are
circular spacers. See charts on the following pages.
.085" (2.2 mm) wide unless otherwise indicated.

WS - Wide Slot None

The abbreviation is followed by the slot width, for example
WS125 indicates a slot width of .125"

OE - Open End Maximum slice opening is 1/2" (12.7 mm)

The slots are completely cut through to the trailing with 1.4" diameter circular spacers.
Other restrictions apply when using large diameter
2 edge (2).
circular spacers. See charts on the following pages.

G - Guide For 5/8"---3/4" (15.9-19.1 mm) slice opening.

The stripper plate guide has the profile shown. The slots
are .085" wide unless otherwise indicated. The guide is
typically used with the extended secondary stripper plate.
(See the following pages).
10
 Parts: Stripper Plates 10.65

Chart 2 Stripper Plates Example:

Slot Feature
Circular Part Number is followed by the slot spacing in inches and the following abbreviations. Part
Spacing Abbreviation
Number
Knife and STD = Standard Profile R = Relieved Profile (inch) (see previous page)
Feed Disc WS = Wide Slot, slot width, decimal inch OE = Open End
Spacing G = Guide
43172 - 1/4 (STD, WS 125)
inch mm Stripper Plate (mounts to the slice gate)
43080 - 1/8 (STD) 43087 - 1/8 (R)
1/8 3.2
IMPORTANT Do not use 1/8" stripper plates at larger cut sizes; the ribs may be damaged.
.150 3.8 43182 - .150 (STD)
5/32 4.0 43081 - 5/32 (STD) 43084 - 5/32 (R) 43090 - 5/32 (R, OE)
3/16 4.8 43082 - 3/16 (STD) 43085 - 3/16 (R) 43088 - 3/16 (R, WS 110)
43226 - 3/16 (G) 43254 - 3/16 (OE)
7/32 5.6 43231 - 7/32 (STD)
43083 - 1/4 (STD) 43086 - 1/4 (R) 43172 - 1/4 (STD, WS 125)
1/4 6.4
43089 - 1/4 (R, OE)
9/32 7.1 43175 - 9/32 (STD)
.290 7.4 42763 - .290 (STD)
19/64 7.5 43171 - 19/64 (STD)
.300 7.6 43168 - .300 (STD)
43166 - 5/16 (STD) 43207 - 5/16 (R) 43177 - 5/16 (STD, WS 188)
5/16 7.9
43184 - 5/16 (STD, WS 125) 43186 - 5/16 (G, WS 125)
11/32 8.7 43179 - 11/32 (STD)
43082 - 3/16 (STD) 43085 - 3/16 (R) 43226 - 3/16 (G)
43254 - 3/16 (OE) 43088 - 3/16 (R, WS 110) 43164 - 3/8 (STD)
3/8 9.5
43208 - 3/8 (R) 43173 - 3/8 (STD, WS 188) 43183 - 3/8 (STD, WS 125)
43176 - 3/8 (OE) 43188 - 3/8 (G) 43185 - 3/8 (G, WS 125)
7/16 11.1 43231 - 7/32 (STD) 43174 - 7/16 (STD)
43083 - 1/4 (STD) 43086 - 1/4 (R) 43172 - 1/4 (STD, WS 125)
1/2 12.7 43089 - 1/4 (R, OE) 43162 - 1/2 (STD, WS 188)
43167 - 1/2 (STD) 43209 - 1/2 (R) 43204 - 1/2 (G)
9/16 14.3 43175 - 9/32 (STD) 43181 - 9/16 (STD, WS 188)
19/32 15.1 43171 - 19/64 (STD) 43180 - 19/32 (WS 188)
43166 - 5/16 (STD) 43207 - 5/16 (R) 43177 - 5/16 (STD, WS 188)
5/8 15.9 43184 - 5/16 (STD, WS 125) 43143 - 5/8 (STD) 43210 - 5/8 (R)
43144 - 5/8 (OE) 10
43082 - 3/16 (STD) 43085 - 3/16 (R) 43088 - 3/16 (R, WS 110)
43226 - 3/16 (G) 43254 - 3/16 (OE) 43172 - 1/4 (STD, WS 125)
43089 - 1/4 (R, OE) 43083 - 1/4 (STD) 43086 - 1/4 (R)
3/4 19.1
43164 - 3/8 (STD) 43173 - 3/8 (STD, WS 188) 43183 - 3/8 (STD, WS 125)
43208 - 3/8 (R) 43176 - 3/8 (OE) 43188 - 3/8 (G)
43185 - 3/8 (G, WS 125) 43169 - 3/4 (STD)
7/8 22.2 43174 - 7/16 (STD)
43083 - 1/4 (STD) 43086 - 1/4 (R) 43172 - 1/4 (STD, WS 125)
1 25.4 43089 - 1/4 (R, OE) 43167 - 1/2 (STD) 43209 - 1/2 (R)
43162 - 1/2 (STD, WS 188) 43204 - 1/2 (G)
43083 - 1/4 (STD) 43086 - 1/4 (R) 43172 - 1/4 (STD, WS 125)
1-1/2 38.1 43089 - 1/4 (R, OE) 43167 - 1/2 (STD) 43209 - 1/2 (R)
43162 - 1/2 (STD, WS 188) 43204 - 1/2 (G) 43169 - 3/4 (STD)
1-3/4 44.5 43083 - 1/4 (STD) 43172 - 1/4 (WS 125) 43174 - 7/16 (STD)
43083 - 1/4 (STD) 43086 - 1/4 (R) 43172 - 1/4 (WS 125)
2 50.8 43089 - 1/4 (R, OE) 43167 - 1/2 (STD) 43209 - 1/2 (R)
43162 - 1/2 (STD, WS 188) 43204 - 1/2 (G)
 10.66 Parts: Stripper Plates, secondary

See chart 1 below for stripper plate features and restrictions.

Chart 2 on the next page lists stripper plates for use at different circular knife or feed disc spacing.
The following pages show stripper plates used at different slice settings.
See Section 6 Machine Setup for a description of stripper plates and application information.

Chart 1
Abbreviations and Descriptions Restrictions
STD - Standard (secondary) The secondary stripper plates cannot be used with
Standard profile for the secondary stripper plate. The large diameter circular knife spacers.
slots are .093" (2.4 mm) wide unless otherwise indicated;
available with wide slots (WS), see below.

EXT - Extended (secondary) The secondary stripper plates cannot be used with
The profile of the extended secondary stripper large diameter circular knife spacers.
plate (3) is wider at the base compared to the profile of
the standard secondary stripper plate (4). The slots are
4 3
.093" (2.4 mm) wide unless otherwise indicated; available
with wide slots (WS), see below.

WS - Wide Slot The secondary stripper plates cannot be used with

The abbreviation is followed by the slot width, for large diameter circular knife spacers.
example: WS125 indicates a slot width of .125".

10
 Parts: Stripper Plates, secondary 10.67

Item Quantity Part Number and

Secondary Description
Stripper Plates
Chart 2 Example:
Slot Feature
Circular Part Number is followed by the slot spacing in inches and the following abbreviations. Part
Spacing Abbreviation
Number
Knife and STD = Standard Profile (inch) (see previous page)
Feed Disc WS = Wide Slot, slot width, decimal inch
Spacing 42777 - 1/4 (STD, WS 125)
EXT = Extended
inch mm Secondary Stripper Plate (mounts to the circular support)
1/8 3.2 42594 - 1/8 (STD)
5/32 4.0 42595 - 5/32 (STD)
3/16 4.8 42596 - 3/16 (STD) 43227 - 3/16 (EXT) 42908 - 3/16 (STD, WS 110)
1/4 6.4 42597 - 1/4 (STD) 42777 - 1/4 (STD, WS 125)
19/64 7.5 42784 - 19/64 (STD)
.300 7.6 42621 - .300 (STD)
5/16 7.9 42598 - 5/16 (STD) 43097 - 5/16 (EXT, WS 125)
11/32 8.7 42817 - 11/32 (STD)
42596 - 3/16 (STD) 43227 - 3/16 (EXT) 42908 - 3/16 (STD, WS 110)
3/8 9.5 42599 - 3/8 (STD) 42808 - 3/8 (STD, WS 250) 43023 - 3/8 (EXT)
43096 - 3/8 (EXT, WS 125) 43342 - 3/8 (STD, WS 125)
7/16 11.1 42494 - 7/16 (STD)
42597 - 1/4 (STD) 42777 - 1/4 (STD, WS 125) 42654 - 1/2 (STD, WS 250)
1/2 12.7
43253 - 1/2 (EXT, WS 250)
9/16 14.3 42835 - 9/16 (STD, WS 250)
19/32 15.1 42943 - 19/32 (STD, WS 250)
42598 - 5/16 (STD) 43097 - 5/16 (EXT, WS 125) 42770 - 5/8 (STD)
5/8 15.9
42655 - 5/8 (STD, WS 250)
42596 - 3/16 (STD) 42908 - 3/16 (STD, WS 110) 43227 - 3/16 (EXT)
42597 - 1/4 (STD) 42777 - 1/4 (STD, WS 125) 42599 - 3/8 (STD)
3/4 19.1
42808 - 3/8 (STD, WS 250) 43023 - 3/8 (EXT) 43096 - 3/8 (EXT, WS 125)
42656 - 3/4 (STD, WS 250) 42556 - 3/4 (STD, 1" Slice)
7/8 22.2 42494 - 7/16 (STD) 42473 - 7/8 (STD) 42809 - (STD, WS 250)
42597 - 1/4 (STD) 42777 - 1/4 (STD, WS 125) 42654 - 1/2 (STD, WS 250)
1 25.4
42470 - 1 (STD) 42495 - 1 (For Feed Discs) 43253 - 1/2 (EXT, WS 250)
42597 - 1/4 (STD) 42777 - 1/4 (STD, WS 125) 42654 - 1/2 (STD, WS 250)
1-1/2 38.1
42656 - 3/4 (STD, WS 250) 42556 - 3/4 STD, 1" Slice) 43253 - 1/2 (EXT, WS 250)
1-3/4 44.5 42494 - 7/16 (STD) 42473 - 7/8 (STD) 42809 - 7/8 (STD, WS 250)

2 50.8
42597 - 1/4 (STD) 42777 - 1/4 (STD, WS 125) 42654 - 1/2 (STD, WS 250) 10
42470 - 1 (STD) 43253 - 1/2 (EXT, WS 250)
 10.68 Parts: Stripper Plate Spacers and Shims

10
Item Quantity Part Number and Description
1 1 * - Stripper Plate (mounts to the slice gate)
2 3 10044 - Hex Head Cap Screw, 5/16-18 x 5/8", s.s.
3 1 42394 - Stripper Plate Spacer, 0"-1/4" (0-6 mm, includes items 8–9)
4 1 42393 - Stripper Plate Spacer, 1/4"-1/2" (6-13 mm, includes items 8–9)
5 1 42392 - Stripper Plate Spacer, 1/2"-3/4" (13-19 mm, includes items 8–9; can be used above 3/4"
slice thickness if a circular spindle is not used)
6 1 42498 - Stripper Spacer, leafy product (up to 3/16"; includes items 8–9)
7 1 43205 - Stripper Spacer, 3/16"-1/2", leafy product (includes items 8–9; used for increased
capacity on cabbage shreds)
8 2 10271 - Dowel Pin, 5/16" x 1/2", s.s.
9 2 10221 - Dowel Pin, 1/4" x 1/2", s.s.
10 3 10424 - Socket Head Cap Screw, 1/4-20 x 3/8", s.s., low head
11 1 42491 - Shim, .048", stripper spacer (for cutting leafy or compressible product; decreases the
maximum slice opening)
12 1 42492 - Shim, .077", stripper spacer (for cutting leafy or compressible product; decreases the
maximum slice opening)
13 1 * - Stripper Plate, secondary (mounts to the circular support)
14 3 10047 - Hex Head Cap Screw, 5/16-18 x 1", s.s.

* See charts on the next page.

 Parts: Stripper Plate Spacers and Shims 10.69

Stripper Plate Spacers and Slice Setting

The stripper plate spacer (1) is installed between the stripper plate and slice 2 1
gate. Choose a spacer based on the slice setting. A shim can be used as shown
in the illustration on the previous page (typically used with leafy or compressible
products). The use of a shim will restrict the slice opening.
Charts 1, 2 and 3: the slice range (2) is marked on the spacer. The top of the
range applies when using 1.4" diameter circular knife spacers.
Chart 4: the slice setting is restricted when using large diameter circular knife
spacers. 2
Chart 1 Chart 2
Standard Spacer Slice Opening Relieved Stripper Spacer Slice Opening
Stripper (S) Range (A) Plate (R) (S) Range (A)
Plate (STD) Part Number inch mm Part Number inch mm
Without Standard Secondary Stripper Plate With Standard Secondary Stripper Plate

42394 0 - 1/4 0-6 42394 0 - 1/4 0-6

42393 1/4 - 1/2 6 - 13 42393 1/4 - 1/2 6 - 13

42392 1/2 - 3/4 13 - 19 42392 1/2 - 9/16 13 - 14

With Standard Secondary Stripper Plate

42498 0 - 3/16 0-5
42394 0 - 1/4 0-6

42393 1/4 - 1/2 6 - 13 43205 3/16 - 3/8 5 - 10

43205 3/16 - 3/8 5 - 10

42392 1/2 - 5/8 13 - 16
Chart 4
Chart 3 Maximum slice opening with large diameter circular knife spacers
Secondary Stripper Spacer Slice Opening Circular Stripper Maximum Circular Stripper Maximum
Plates (S) Range (A) Knife Plate Slice Knife Plate Slice
Part Number inch mm Spacer Spacer Opening Spacer Spacer Opening 10
Secondary Stripper Plate, Standard (STD) (D) (S) (M) (D) (S) (M)
Diameter Part Number inch mm Diameter Part Number inch mm
---- 3/4 - 1 19 - 25
Standard Stripper Plate Relieved Stripper Plate

Secondary Stripper Plate, Extended (EXT) with Guide (G)

42392 5/8 - 3/4 16 - 19

42394 1/4 6.4 42394 1/4 6.4
1.80" 42393 1/2 12.7 1.80" 42393 3/8 9.5
42392 1/2 12.7 42392 1/2 12.7
42394 3/16 4.8 42394 1/4 6.4
2.08" 42393 5/16 7.9 2.08" 42393 1/4 6.4
42392 ---- ---- 42392 5/16 7.9
 10.70 Parts: Crosscut Knife Spindle Assemblies,
3/32"–1/4" (2.4mm–6.4mm)

Use 65 in/lb
Torque Wrench

10
 Parts: Crosscut Knife Spindle Assemblies, 10.71
3/32"–1/4" (2.4mm–6.4mm)
Item Quantity Part Number and Description
– 1 * - Crosscut Knife Spindle Assembly, narrow knife (includes items 1–5)
1 1 * - Spindle, crosscut
2 * 42460 - Knife, crosscut, straight, narrow
3 2 42554 - Retaining Ring, small cuts 3/32" to 1/4" (for narrow knife spindles)
4 12 10090 - Socket Head Cap Screw, 1/4-20 x 5/8", s.s.
5 1 42315 - Protective Sleeve, crosscut spindle, DC (supplied with spindle assembly)

* See Chart 1 below.

Alternate retaining ring

6 2 42458 - Retaining Ring

Chart 1 3/32"–1/4", Straight Cut, narrow knife

*Size of Cut Item 1 Item 2

Spindle
Crosscut Knife
Assembly
inch mm Spindle Quantity
3/32 2.4 42752 42751 114
1/8 3.2 42461 42459 82
5/32 4.0 42463 42462 66
3/16 4.8 42476 42475 55
7/32 5.6 42500 42499 48
1/4 6.4 42465 42464 41
* See Drive Parts for other crosscut sizes that can be
produced by changing the timing pulley on the bearing
spindle.

Actual Product Dimensions from Crosscut Spindle Assembly on Potatoes and Carrots: Crosscut size may
vary from the dimensions listed in Chart 1 above. Chart 2 below lists the actual size of crosscut produced for
these products. Potatoes are peeled and soaked in hot water for 15 minutes. If feed discs are used, they should
be selected based on slice thickness. Properly sized feed discs will produce the best alignment of the product as
it enters the crosscut knives.
10
Chart 2 Actual Product Dimension from Crosscut (straight cut)
Spindle Peeled
Size of Cut Assembly Carrots
Potatoes
inch mm Part Number inch mm inch mm
3/32 2.4 42752 0.097 2.46 0.097 2.46
1/8 3.2 42461 0.132 3.35 --- ---
5/32 4.0 42463 0.167 4.24 --- ---
3/16 4.8 42476 0.199 5.05 --- ---
7/32 5.6 42500 0.213 5.41 --- ---
1/4 6.4 42465 0.279 7.09 0.267 6.78
 10.72 Parts: Crosscut Knife Spindle Assemblies,
9/32"–.583" (7.1mm–14.8mm)

.125" (3.2 mm)

.145" (3.7 mm)

.076" (1.9 mm)

10
Use 40 in/lb
Torque Wrench
 Parts: Crosscut Knife Spindle Assemblies, 10.73
9/32"–.583" (7.1mm–14.8mm)
Item Quantity Part Number and Description
– 1 * - Crosscut Knife Spindle Assembly, standard knife (includes items 1–6)
1 1 * - Spindle, crosscut
2 * 42281 - Knife, crosscut, straight (use in straight cut assemblies)
3 * 42267 - Knife, crosscut, crinkle (.076" deep, use in crinkle cut assemblies)
4 2 42553 - Retaining Ring, flanged, medium cut
5 12 10090 - Socket Head Cap Screw, 1/4-20 x 5/8", s.s.
6 1 42315 - Protective Sleeve, crosscut spindle, DC (supplied with spindle assembly)

Alternate crinkle knives and retaining ring

7 1 42664 - Knife, crosscut, deep crinkle, .125" (requires slicing knife/holder for .125" crinkle)
1 42848 - Knife, crosscut, deep crinkle, .145" (requires slicing knife/holder for .145" crinkle)
– 2 42279 - Retaining Ring (not shown)

* See chart 1 below.

Chart 1
9/32"–.583", Straight and Crinkle Knives, standard width knives NOTICE
*Size of Cut Spindle Spindle Item 1 Items 2, 3, 7 The straight and crinkle crosscut
Assembly Assembly Crosscut Knife knife assemblies require different
inch mm (straight cut) (crinkle cut) Spindle Quantity slicing knives and holders. Use
the correct slicing knife or holder
9/32 7.1 42406 42417 42337 36
or damage to parts will occur.
19/64 7.5 42611 ---- 42610 35
5/16 7.9 42407 42418 42338 33
11/32 8.7 42800 ---- 42801 31
3/8 9.5 42408 42419 42341 28
7/16 11.1 42409 42420 42340 24
15/32 11.9 ---- 42426 42774 23
1/2 12.7 42410 42421 42339 21
9/16 14.3 42411 42422 42336 19
.583 14.8 ---- 42586 42585 18
* See Drive Parts for other crosscut sizes that can be produced by
changing the timing pulley on the bearing spindle.
Actual Product Dimensions from Crosscut Spindle Assembly on Potatoes and Carrots:
Crosscut size may vary from the dimensions listed in Chart 1 above. Chart 2 below lists the overall
thick
actual size of crosscut produced for these products. Potatoes are peeled and soaked in hot
water for 15 minutes. If feed discs are being used, they should be selected based on slice
thickness. Properly sized feed discs will produce the best alignment of the product as it enters
the crosscut knives. The thick and overall dimensions are given for crinkle cuts. 10
Chart 2
Item 1 Actual Product Dimensions from Crosscut
Crosscut Straight Cut Crinkle Cut (.076") Deep Crinkle Cut (.125") Deep Crinkle Cut (.145")
Size of Cut
Spindle Peeled Peeled Potatoes Peeled Potatoes Peeled Potatoes
Carrots
Part Potatoes inch mm inch mm inch mm
inch mm Number inch mm inch mm thick/overall thick/overall thick/overall thick/overall thick/overall thick/overall
9/32 7.1 42337 0.275 6.99 0.270 6.86 .263/.315 6.68/8.00 --- --- --- ---
19/64 7.5 42610 0.291 7.39 0.285 7.24 --- --- --- --- --- ---
5/16 7.9 42338 0.322 8.18 0.319 8.10 .296/.356 7.52/9.04 --- --- --- ---
11/32 8.7 42801 0.336 8.53 --- --- --- --- --- --- --- ---
3/8 9.5 42341 0.391 9.93 0.387 9.83 .349/.398 8.86/10.11 .344/.442 8.74/11.23 .323/.431 8.20/10.95
7/16 11.1 42340 0.433 11.00 --- --- .413/.459 10.49/11.66 .399/.502 10.13/12.75 .353/.496 8.97/12.60
15/32 11.9 42774 0.468 11.89 --- --- .420/.465 10.67/11.81 --- --- .373/.524 9.47/13.31
1/2 12.7 42339 0.529 13.44 --- --- .485/.529 12.32/13.44 .478/.558 12.14/14.17 .434/.545 11.02/13.84
9/16 14.3 42336 0.540 13.72 --- --- .525/.566 13.33/14.38 --- --- --- ---
.583 14.8 42585 0.569 14.45 --- --- .561/.595 14.25/15.11 --- --- --- ---
 10.74 Parts: Crosscut Knife Spindle Assemblies,
.583"–1-1/2" (14.8mm–38.1mm)

Use 40 in/lb
Torque Wrench

10
 Parts: Crosscut Knife Spindle Assemblies, 10.75
.583"–1-1/2" (14.8mm–38.1mm)
Item Quantity Part Number and Description
– 1 * - Crosscut Knife Spindle Assembly, wide knife (includes items 1, 2, 6 and 7, and
one set of items 3, 4 or 5 retaining rings; See chart below)
1 1 * - Spindle, crosscut
2 * 42446 - Knife, crosscut, straight, wide (used only for cuts larger than 9/16")
3 2 42552 - Retaining Ring, flanged, large cuts (used only for cuts larger than 9/16")
4 2 42680 - Retaining Ring, large cuts, 6 holes (used only with 42679 spindle)
5 2 42810 - Retaining Ring, large cuts, 7 holes (used only with 42812 spindle)
6 * 10090 - Socket Head Cap Screw, 1/4-20 x 5/8", s.s.
7 1 42315 - Protective Sleeve, crosscut spindle, DC (supplied with spindle assembly)

* See chart below.

Alternate Retaining Ring

8 2 42280 - Retaining Ring, large cuts

.583"–1-1/2", Straight Cut, wide knife

**Size of Cut Crosscut Item 1 Item 2 Items 3, 4, 5 Item 6, Screw
Knife Spindle Crosscut Knife Retaining For Retaining Rings
inch mm Assembly Spindle Quantity Rings Quantity
.583 4.8 42412 42344 18 42552 10
5/8 15.9 42413 42450 17 42552 10
3/4 19.1 42414 42342 14 42552 10
7/8 22.2 42505 42504 12 42552 10
1 25.4 42416 42343 10 42552 10
1-3/16 30.2 42681 42679 9 42680 12
1-1/2 38.1 42811 42812 7 42810 14
** See Drive Parts for other crosscut sizes that can be produced by changing the timing pulley
on the bearing spindle.

10
 10.76 Parts: Crosscut Knife Spindle Assemblies, heavy duty

10
 Parts: Crosscut Knife Spindle Assemblies, heavy duty 10.77

Item Quantity Part Number and Description

– 1 * - Crosscut Knife Spindle Assembly, heavy duty (includes items 1–6)
1 1 * - Spindle, crosscut, heavy duty
2 * 42537 - Knife, crosscut, heavy duty
3 * 45372 - Hex Head Screw, special
4 2 42587 - Retaining Ring, heavy duty spindle
5 6 10235 - Socket Head Cap Screw, 10-24 x 1/2", s.s.
6 1 42315 - Protective Sleeve, crosscut spindle, DC (supplied with spindle assembly)

– 1 ** - Crosscut Knife Spindle Assembly, heavy duty (includes items 7–12)

7 1 ** - Spindle, crosscut, heavy duty
8 * 45089 - Knife, crosscut, wide width
9 * 17370 - Hex Head Screw, special, 5/16-18 x 5/8", s.s.
10 2 ** - Retaining Ring
11 * 10235 - Socket Head Cap Screw, 10-24 x 1/2", s.s.
12 1 42315 - Protective Sleeve, crosscut spindle, DC (supplied with spindle assembly)

* See chart 1 below.

** See chart 2 below.

Chart 1 3/8"–1/2", Crosscut Knife Spindle Assembly, Heavy Duty

Size of Cut§ Crosscut Item 1 Item 2 Item 3
Knife Spindle Crosscut Knife Screw
inch mm Assembly Spindle Quantity Quantity
3/8 9.5 42541 42539 28 112
1/2 12.7 42542 42540 21 84

Chart 2 3/4"–3-1/2", Crosscut Knife Spindle Assembly, Heavy Duty

Size of Cut § Crosscut Item 7 Item 8 Item 9 Item 10 Item 11
Knife Spindle Crosscut Knife Screw Retaining Screw
inch mm Assembly Spindle Quantity Quantity Ring Quantity
3/4 19.1 42757 42758 14 56 42756 6
1 25.4 42628 42627 10 40 42593 6
1.16 29.5 42955 42954 9 36 42756 6
1-5/16 33.3 42683 42682 8 32 42786 8
1-1/2 38.1 42448 42447 7 28 42593 6 10
§§
1-3/4 44.5 42448 42447 7 28 42593 6
2 50.8 42858 42856 5 20 --- ---
2 50.8 42859 42856 5 20 42857 10
2-1/2 63.5 42620 42619 4 16 --- ---
3-1/2 88.9 42952 42951 3 12 --- ---
§
See Drive Parts for other crosscut sizes that can be produced by changing the timing
pulley on the bearing spindle.
§§
This size requires changing the crosscut pulley; replace the 42244 pulley with 42486
Pulley, timing, 63 teeth, Dayco.
 10.78 Parts: Shred Spindle Assemblies and Rotating Deflector

Use 65 in/lb
Torque Wrench
for Item 8

30 Point

Item 5 Shred Discs

10 (20 Point Shred Spindle
Assembly 42778 shown above)

4 Point 10 Point 12 Point 16 Point 20 Point

 Parts: Shred Spindle Assemblies and Rotating Deflector 10.79

Item Quantity Part Number and Description

1 3 24138 - Socket Head Cap Screw, 3/8-16 x 1-1/4", hard
2 1 * - Spindle Assembly, crosscut, shred (includes items 3–8)
3 1 42779 - Spindle, crosscut, shred
4 1 42782 - Alignment Rod, shredding, crosscut
5 * * - Shredding Disc, crosscut
6 * * - Spacer, shredding, crosscut (.25" thick)
7 2 42280 - Retaining Ring, large cuts
8 10 10090 - Socket Head Cap Screw, 1/4-20 x 5/8", s.s.
9 2 42552 - Retaining Ring, flanged, large cut (alternate part for item 7, part number 42280)

* See chart below.

Item 2 Item 5 Shredding Disc Shredding Item 6 Shredding

Shred Spindle Shredding Thickness And Disc Shredding Spacer
Assembly** Disc Number Of Points Quantity Spacer Quantity
43306 43304 .25" (6.35 mm) x 4 21 42781 21
43224 43223 .25" (6.35 mm) x 10 21 42781 21
43301 43299 .25" (6.35 mm) x 12 21 42781 21
43302 43300 .25" (6.35 mm) x 16 21 42781 21
42778 42780 .25" (6.35 mm) x 20 21 42781 21
43303 43062 .125" (3.18 mm) x 30 36 43225 36
** The shredding spindle can be assembled with other quantities of discs and spacers. The total number of
.25" thick discs and spacers must equal 42; the total number of .125" thick discs and spacers must equal 72.
The number and arrangement of discs will affect the shred; consult an Urschel representative for additional
information.

Rotating deflector
10 – 43025 - Rotating Deflector (for slicing and strip cutting applications)
11 – 24138 - Socket Head Cap Screw, 3/8-16 x 1-1/4", hard

10
 10.80 Parts: Spindle Assembly, Impeller Shaft

10
 Parts: Spindle Assembly, Impeller Shaft 10.81

Item Quantity Part Number and Description

1 1 * - Spindle Assembly, jack shaft
2 6 10430 - Hex Head Cap Screw, 3/8-16 x 1-3/8", s.s.
3 1 43212 - Spindle Assembly, impeller shaft (includes items 4–17)
4 1 43213 - Impeller Shaft
5 1 19182 - Key, 1/4" x 1/4" x 2-3/8"
6 1 43215 - Seal
– 1 24053 - Roller Bearing (includes items 7–8)
7 1 24054 - Roller Bearing Cup, 3-7/16" O.D.
8 1 24058 - Roller Bearing Cone, 1-3/4" I.D.
9 1 43214 - Bearing Housing, impeller
10 1 11401 - Grease Fitting, 1/8", straight, s.s. (shipping only; remove when installing spindle)
– 1 24052 - Roller Bearing (includes items 11–12)
11 1 24054 - Roller Bearing Cup, 3-7/16" O.D.
12 1 24056 - Roller Bearing Cone, 1-5/8" I.D.
13 1 42677 - Hub, impeller shaft (includes item 14)
14 1 10141 - Socket Set Screw, 5/16-18 x 1/2", Nylok, s.s.
15 1 24140 - Shims, set of six
16 1 24046 - End Cap
17 3 10407 - Socket Head Cap Screw, 1/4-20 x 3/4", Nylok

* See Spindle Assembly, jack shaft.

10
 10.82 Parts: Spindle Assembly, Circular Shaft and Drive Couplings

10
 Parts: Spindle Assembly, Circular Shaft and Drive Couplings 10.83

Item Quantity Part Number and Description

1 4 10110 - Socket Head Cap Screw, 3/8-16 x 1-1/4", s.s.
2 1 43190 - Spindle Assembly, circular shaft (includes items 3–16)
3 1 42583 - Shaft, circular spindle, 1/4-20 holes
4 1 18066 - Key, 1/4" x 1/4" x 2"
5 1 42221 - Seal
– 1 42218 - Roller Bearing (includes items 6–7)
6 1 42216 - Roller Bearing Cup, 2-7/16" O.D.
7 1 42220 - Roller Bearing Cone, 1-1/4" I.D.
8 1 43189 - Bearing Housing, circular shaft
9 1 43191 - O-Ring, 3/32" x 4-1/4" x 4-7/16"
– 1 42215 - Roller Bearing (includes items 10–11)
10 1 42216 - Roller Bearing Cup, 2-7/16" O.D.
11 1 42217 - Roller Bearing Cone, 1-3/16" I.D.
12 1 42222 - Hub, circular spindle shaft (includes item 13)
13 1 10141 - Socket Set Screw, 5/16-18 x 1/2", Nylok, s.s.
14 1 42457 - Shims, set of six
15 1 53036 - End Cap
16 3 10406 - Socket Head Cap Screw, 10-24 x 3/4", Nylok
17 1 42640 - Drive Coupling, 2.3" O.D. (includes item 18)
18 2 37040 - Dowel Pin, 1/4" x 5/8", 416 s.s.
19 3 10593 - Lock Washer, 1/4", vibration resistant
20 3 10592 - Button Head Screw, 1/4-20 x 5/8"
21 1 43126 - Ring, circular spindle assembly (includes item 22)
22 4 10499 - Socket Set Screw, 3/8-16 x 3/4", s.s., brass tip
23 4 10112 - Socket Head Cap Screw, 3/8-16 x 1", s.s.

Drive coupling for heavy duty applications

24 1 42823 - Drive Coupling*, 2.3" O.D., hard (use with 42806 heavy duty circular knife shaft,
includes item 25)
25 2 37040 - Dowel Pin, 1/4" x 5/8", 416 s.s.

IMPORTANT
* Using this drive coupling in applications where cutting parts are slowed or stopped abruptly may cause other
components to fail. Contact an Urschel representative for more information before ordering.

10
 10.84 Parts: Spindle Assembly, Circular Shaft and Flexible Coupling

10
 Parts: Spindle Assembly, Circular Shaft and Flexible Coupling 10.85

Item Quantity Part Number and Description

1 4 10110 - Socket Head Cap Screw, 3/8-16 x 1-1/4", s.s.
2 1 43241 - Spindle Assembly*, circular shaft (includes items 3–20)
3 1 42217 - Shaft, circular spindle (includes item 4)
4 2 38065 - Dowel Pin, 5/16" x 5/8", 416 s.s.
5 1 18066 - Key, 1/4" x 1/4" x 2"
6 1 42221 - Seal
– 1 42218 - Roller Bearing (includes items 7–8)
7 1 42216 - Roller Bearing Cup, 2-7/16" O.D.
8 1 42220 - Roller Bearing Cone, 1-1/4" I.D.
9 1 43243 - Bearing Housing, circular shaft
10 1 43191 - O-Ring, 3/32" x 4-1/4" x 4-7/16"
– 1 42215 - Roller Bearing (includes items 11–12)
11 1 42216 - Roller Bearing Cup, 2-7/16" O.D.
12 1 42217 - Roller Bearing Cone, 1-3/16" I.D.
13 1 42222 - Hub, circular spindle shaft (includes item 14)
14 1 10141 - Socket Set Screw, 5/16-18 x 1/2", Nylok, s.s.
15 1 42457 - Shims, set of six
16 1 53036 - End Cap
17 3 10406 - Socket Head Cap Screw, 10-24 x 3/4", Nylok
18 1 43219 - Key, drive coupling
19 1 10441 - Flat Head Screw, 10-24 x 1/2", s.s., Nylok
20 1 43216 - Drive Coupling
21 1 43126 - Ring, circular spindle assembly (includes item 22)
22 4 10499 - Socket Set Screw, 3/8-16 x 3/4", s.s., brass tip
23 4 10112 - Socket Head Cap Screw, 3/8-16 x 1", s.s.

* This assembly can be used if mechanical wear causes slight misalignment of the circular spindle resulting in
reduced life of the circular shaft.

10
 10.86 Parts: Spindle Assembly, Circular Shaft with Integrated Coupling

10
 Parts: Spindle Assembly, Circular Shaft with Integrated Coupling 10.87

Item Quantity Part Number and Description

1 4 10110 - Socket Head Cap Screw, 3/8-16 x 1-1/4", s.s.
2 1 43244 - Spindle Assembly*, circular shaft, drive coupling (includes items 3–16)
3 1 42864 - Shaft, circular spindle, drive coupling
4 1 18066 - Key, 1/4" x 1/4" x 2"
5 1 42221 - Seal
– 1 42218 - Roller Bearing (includes items 6–7)
6 1 42216 - Roller Bearing Cup, 2-7/16" O.D.
7 1 42220 - Roller Bearing Cone, 1-1/4" I.D.
8 1 43189 - Bearing Housing, circular shaft
9 1 43191 - O-Ring, 3/32" x 4-1/4" x 4-7/16"
– 1 42215 - Roller Bearing (includes items 10–11)
10 1 42216 - Roller Bearing Cup, 2-7/16" O.D.
11 1 42217 - Roller Bearing Cone, 1-3/16" I.D.
12 1 42222 - Hub, circular spindle shaft (includes item 13)
13 1 10141 - Socket Set Screw, 5/16-18 x 1/2", Nylok, s.s.
14 1 42457 - Shims, set of six
15 1 53036 - End Cap
16 3 10406 - Socket Head Cap Screw, 10-24 x 3/4", Nylok
17 1 43126 - Ring, circular spindle assembly (includes item 18)
18 4 10499 - Socket Set Screw, 3/8-16 x 3/4", s.s., brass tip
19 4 10112 - Socket Head Cap Screw, 3/8-16 x 1", s.s.

* This assembly can be used in heavy duty applications such as frozen meat where excessive wear or fracture
of the standard coupling may occur.

IMPORTANT
Using this assembly in applications where cutting parts are slowed or stopped abruptly may cause other
components to fail. Contact an Urschel representative for more information before ordering.

10
 10.88 Parts: Spindle Assembly, Crosscut Shaft

10
 Parts: Spindle Assembly, Crosscut Shaft 10.89

Item Quantity Part Number and Description

1 4 10113 - Socket Head Cap Screw, 3/8-16 x 1-1/4", s.s.
2 1 42205 - Spindle Assembly, crosscut shaft (includes items 3–17)
3 1 42207 - Shaft, crosscut (includes item 4)
4 1 24139 - Stud, 1/2-13 x 2-1/16", special
5 1 19182 - Key, 1/4" x 1/4" x 2-3/8"
6 1 42208 - Seal
– 1 24053 - Roller Bearing (includes items 7–8)
7 1 24054 - Roller Bearing Cup, 3-7/16" O.D.
8 1 24058 - Roller Bearing Cone, 1-3/4" I.D.
9 1 42206 - Spindle Housing, crosscut
10 1 42210 - O-ring, 3/32" x 5-1/2" x 5-11/16", Viton
– 1 22037 - Roller Bearing (includes items 11–12)
11 1 22183 - Roller Bearing Cup, 2-5/8" O.D.
12 1 22184 - Roller Bearing Cone, 1-3/8" I.D.
13 1 42209 - Hub, crosscut spindle shaft (includes item 14)
14 1 10141 - Socket Set Screw, 5/16-18 x 1/2", Nylok, s.s.
15 1 53042 - Shims, set of six
16 1 53036 - End Cap
17 3 10406 - Socket Head Cap Screw, 10-24 x 3/4", Nylok
18 1 43125 - Ring, crosscut spindle assembly (includes item19)
19 2 10499 - Socket Set Screw, 3/8-16 x 3/4", s.s., brass tip
20 4 10113 - Socket Head Cap Screw, 3/8-16 x 1-1/4", s.s.

10
 10.90 Parts: Spindle Assembly, Jack Shaft

10
 Parts: Spindle Assembly, Jack Shaft 10.91

Item Quantity Part Number and Description

1 4 42223 - Spindle Assembly, jack shaft (includes items 2–15)
2 1 42224 - Spindle Housing, jack shaft (includes items 3–4)
3 1 10120 - Socket Head Cap Screw, 1/2-13 x 1-1/4", s.s.
4 1 11401 - Grease Fitting, 1/8", straight, s.s. (for shipping only; remove when installing spindle)
5 1 42225 - Shaft, jack
6 1 42366 - Key, 1/4" x 1/4" x 3.69"
– 1 22037 - Roller Bearing (includes items 7–8)
7 1 22138 - Roller Bearing Cup, 2-5/8" O.D.
8 1 22184 - Roller Bearing Cone, 1-3/8" I.D.
– 1 53431 - Roller Bearing (includes items 9–10)
9 1 22183 - Roller Bearing Cup, 2-5/8" O.D.
10 1 53432 - Timken Bearing Cone, modified bore
11 1 42673 - Hub, spindle assembly, jack shaft (includes item 12)
12 1 10141 - Socket Set Screw, 5/16-18 x 1/2", Nylok, s.s.
13 1 53042 - Shims, set of six
14 1 53036 - End Cap
15 1 10406 - Socket Head Cap Screw, 10-24 x 3/4", Nylok

Optional Parts
16 1 43051 - Stop, jack shaft (includes items 17–21; prevents the jack shaft assembly from
rotating under heavy loads or an abrupt stop. Contact an Urschel representative
for additional information before ordering)
17 1 43050 - Stop, jack shaft, sliding plate
18 1 43049 - Stop, jack shaft, lower plate
19 3 10110 - Socket Head Cap Screw, 3/8-16 x 3/4", s.s.
20 3 10009 - Washer, flat, 3/8", s.s., thin
21 1 10395 - Hex Head Cap Screw, 3/4-10 x 4-1/4", s.s. (replaces 1 of 10460 hex head cap
screw, 3/4-10 x 3-3/4", s.s.; See Floor Stands, Covers and Guards, item 9)

Items 22–24 prevent the jack shaft assembly from rotating under high surging heavy loads or from an abrupt
stop. These parts are used with the high speed pulleys only. Contact an Urschel representative for additional
information before ordering.
22 1 10046 - Hex Head Cap Screw, 5/16-18 x 7/8", s.s.
23 1 10014 - Lock Washer, 5/16", s.s.
24 1 13365 - Mounting Lug, 3/4"

10
 10.92 Parts: Lubrication Assembly, with circular and crosscut spindles

10
 Parts: Lubrication Assembly, with circular and crosscut spindles 10.93

Item Quantity Part Number and Description

– 42301 - Lubrication Assembly (includes items 1–8)
1 4 45195 - Bulkhead, connector, female
2 4 11401 - Grease Fitting, 1/8", straight, s.s.
3 2 11419 - Nipple, 1/8", 2" long
4 2 11427 - Elbow, male, 1/4" tube to 1/8" pipe
5 2 11425 - 1/4" Tube To 1/8" Pipe, female
6 4 11411 - Elbow, 45 degree, 1/8", male/female, grease
7 1 42298 - Grease Tube, 20" long
8 3 42299 - Grease Tube, 27" long

10
 10.94 Parts: Lubrication Assembly, without crosscut spindle

10
 Parts: Lubrication Assembly, without crosscut spindle 10.95

Item Quantity Part Number and Description

1 4 45195 - Bulkhead, connector, female
2 1 28132 - Pipe Plug, 1/8"
3 3 11401 - Grease Fitting, 1/8", straight, s.s.
4 1 11419 - Nipple, 1/8", 2" long
5 2 11427 - Elbow, male, 1/4" tube to 1/8" pipe
6 1 11425 - 1/4" Tube To 1/8" Pipe, female
7 2 11411 - Elbow, 45 degree, 1/8", male/female, grease
8 1 42298 - Grease Tube, 20" long
9 2 42299 - Grease Tube, 27" long

10
 10.96 Parts: Lubrication Assembly, without circular and
crosscut spindles

10
 Parts: Lubrication Assembly, without circular and 10.97
crosscut spindles
Item Quantity Part Number and Description
1 4 45195 - Bulkhead, connector, female
2 2 28132 - Pipe Plug, 1/8"
3 2 11401 - Grease Fitting, 1/8", straight, s.s.
4 2 11427 - Elbow, male, 1/4" tube to 1/8" pipe
5 2 42299 - Grease Tube, 27" long

10
 10.98 Parts: Motor and Motor Pulley

10
 Parts: Motor and Motor Pulley 10.99

Item Quantity Part Number and Description

1 1 * - Motor, stainless steel, 1.375" shaft diameter
2 1 23566 - Key, 5/16" x 5/16" x 2-13/32"
3 4 10074 - Hex Head Cap Screw, 1/2-13 x 1-1/2", s.s.
4 4 10016 - Lock Washer, 1/2", s.s.
5 4 10010 - Washer, flat, 1/2", s.s.
6 1 ** - Pulley, timing, RPP 8mm, 1.375" I.D. (includes item 7)
7 2 10139 - Socket Set Screw, 5/16-18 x 5/16", 17-4, Nylok
8 1 42251 - Bracket, belt guard
9 2 10038 - Hex Head Cap Screw, 1/4-20 x 3/4", s.s.
10 1 42250 - Belt Guard
11 1 63825 - Hand Knob, 5/16-18 thread, s.s.
12 1 42249 - Timing Belt, 1600-8M 35 (motor)
13 1 21813 - Fan, SMI, 184/213 frame (for 42579 Stainless Motors, Inc. stainless steel motor, 5 hp)
1 21812 - Fan, SMI, 184/213 frame (for 42579 Baldor stainless steel motor, 5 hp, not shown)

* See charts 1 and 2.

** See charts 3 and 4.

Optional pulleys and belts

14 1 42867 - Pulley, Micro-V, 2.55" O.D., 1.375" I.D., 10 groove (60 Hz single speed and all VFD
supplied machines, includes items 15, 16; speed is similar to 42353, 26 tooth pulley)
1 42851 - Pulley, Micro-V, 3.05" O.D., 1.375" I.D., 10 groove (50 Hz single speed supplied
machines only, includes items 15, 16; speed is similar to 42472, 31 tooth pulley)
15 1 10451 - Socket Set Screw, 1/4-20 x 3/8", Nylok, s.s.
16 1 10450 - Socket Set Screw, 1/4-20 x 1/4", Nylok, s.s.
17 1 42931 - Micro-V-Belt, 610J10 (use with 42867, 60 Hz)
1 42853 - Micro-V-Belt, 650J10 (use with 42851, 50 Hz)
18 1 42852 - Pulley, Micro-V, 8.46" O.D., 2.00" I.D., 10 groove
19 1 42675 - Pulley, timing, 26 teeth, RPP 8mm, 1.375" (narrow, 60 Hz, includes item 20)
1 42670 - Pulley, timing, 31 teeth, RPP 8mm, 1.375" (narrow, 50 Hz, includes item 20)
20 2 10139 - Socket Set Screw, 5/16-18 x 5/16", 17-4, Nylok
21 1 42676 - Timing Belt, 1600-8M 22, narrow

Repair parts for motor 42579, (item 1; see chart 1).

22 1 21899 - Bearing, opposite drive end, Sterling
23 1 21900 - Bearing, drive end, Sterling
24 1 21901 - Seal, opposite drive end, Sterling
25 1 21902 - Slinger, drive end, Sterling
26 1 21903 - Seal, drive end, Sterling
Chart 1 Chart 2 Chart 3
5 hp (3.7 kW) 10 hp (7.5 kW) Motor Pulley, for 5 hp (3.7 kW) motor with VFD
Motor, VFD and Motor, Single Speed Item 6 Running Impeller Circular Crosscut
Motor Pulley Number
Single Speed of Input Speeds Speed Speed Speed
Item 1 Motor Voltage Input Teeth Hertz
Item 1 Motor Voltage Input Part Number Hertz Part Number Hertz RPM RPM RPM
Part Number Hertz 200 50 75 155 1142 994
200 50 208 50 65 134 990 861
208 50 60 124 914 795
220 50 42353 26 50/60
55 113 838 729
220 50 400 50 50 103 762 663
400 50 42332 416 50 45 93 685 596
42579 416 50 380 50
Chart 4
380 50 440 50
440 50 Motor Pulley,for 5 hp (3.7 kW) and
230 60
10 hp (7.5 kW) motors, single speed
230 60 460 60
Item 6 Number Running
10
Input Speeds, Hertz Impeller
460 60 Circular Crosscut
42333 200-208 60 Motor Pulley of Speed Speed Speed
42580 200-208 60 42334 380 60 Part Number Teeth Hertz (for comparison) RPM RPM RPM
42581 380 60 42335 575 60 50 50 103 762 663
42353 26
42582 575 60 60 60 (Standard) 124 914 795
(Single Motor Speed Only) 50 60 (Standard) 124 914 795
42472 31
60 71 148 1090 941
42488 32 60 75 155 1142 994
 10.100 Parts: Drive Parts

10
 Parts: Drive Parts 10.101

Item Quantity Part Number and Description

1 1 42825 - Gear, 10P, 120 teeth, 2.5" I.D., nylon, with inserts
2 6 10132 - Socket Head Cap Screw, 3/8-16 x 1-1/4", Nylok
3 6 10009 - Washer, flat, 3/8", s.s., thin
4 1 53050 - Gear, 10P, 27 teeth, 1.125" I.D., s.s. (includes item 5)
5 2 10397 - Socket Set Screw, 1/4-20 x 3/8", flat point, Nylok
6 1 42223 - Spindle Assembly, jack shaft (includes item 7)
7 2 10120 - Socket Head Cap Screw, 1/2-13 x 1-1/4", s.s.
8 1 19182 - Key, 1/4" x 1/4" x 2-3/8"
9 1 42702 - Pulley, timing, 78 teeth, RPP 8mm
10 1 42703 - Pulley, timing, 85 teeth, RPP 8mm
11 6 10434 - Hex Head Flange Screw, 5/16-18 x 4", s.s., G8
12 6 10288 - Washer, flat, 5/16", s.s., thin
13 6 10306 - Hex Nut, 5/16-18, s.s., locking
14 1 * - Pulley, timing, 54 teeth
15 2 42705 - Flange
16 3 10051 - Hex Head Cap Screw, 5/16-18 x 2", s.s.
17 3 10014 - Lock Washer, 5/16", s.s.
18 2 42243 - Flange
19 1 ** - Pulley, timing, 47 teeth
20 3 10051 - Hex Head Cap Screw, 5/16-18 x 2", s.s.
21 3 10014 - Lock Washer, 5/16", s.s.
22 1 42248 - Timing Belt, 1360-8M 35
23 1 42249 - Timing Belt, 1600-8M 35

Alternate Parts
24 1 42794 - Gear, 10P, 120 teeth, 2.5" I.D., nylon, 2.00" wide (shorter gear teeth are intended to
fail if foreign material stops the cutting parts abruptly)
25 1 42795 - Gear, 10P, 27 teeth, 1.125" I.D., s.s.
26 1 42868 - Gear, 10P, 120 teeth, 2.5" I.D., s.s. (difficult-to-cut products, heavy applications only)
27 1 42932 - Gear, 10P, 27 teeth, 1.125" I.D., s.s.
28 1 42852 - Pulley, Micro-V, 8.46" O.D., 2.00" I.D., 10 groove (use with Micro-V motor pulley and belt)
– 1 42659 - Timing Belt, 1200-8MPT-35 (not shown; use when the crosscut bearing spindle
is not installed)
– 1 43256 - Gear, 10P, 120 teeth, Nylon, with inserts, reduced O.D. (not shown; used in hot and
high ambient temperature locations. Replaces 42825, item 1 or 42868, item 26)
IMPORTANT
Operating in high ambient temperatures (100°F/38°C) may cause gear failure. Contact Urschel for more
information about operating in high temperature environments.

Chart 1* Item 14 Crosscut Pulleys Crosscut pulleys and size of cut: cutting products with
characteristics such as hardness or compressibility may not result
Pulley Number Percent of
in the desired size of cut. By speeding or slowing the spindle,
Part of Standard
the desired size of cut can be produced. Use the pulleys listed to
Number Teeth Speed
increase or decrease the speed of the crosscut spindle.
42244 54 100% (Standard) Dimensional sizes that are not available with the crosscut spindle
42520 40 135% can also be produced. For example, to produce a crosscut
42521 44 123% dimension of .36", the 3/8" crosscut spindle speed can be
42242 47 115% increased to 104% of standard speed with pulley 42522.
To calculate the size of cut that can be produced, use the size of
42522 52 104% the crosscut spindle divided by the percentage from the chart. For
42523 56 96% example, .375" divided by 1.04 = .360".
42524 58 93%
42486 63 86% 10
Chart 2** Item 19 Circular Pulleys
Pulley Number Percent of
Part of Standard
Number Teeth Speed
42242 47 100% (Standard)
42520 40 117%
 10.102 Parts: Electrical Assembly Charts

Electrical Enclosure Assemblies with VFD

Voltage Motor Electrical Assembly Electrical Enclosure Electrical Schematic
Part Number Assembly
Part Feed/Discharge* Page Part Page Part Page
Number One Two Number Number Number Number Number
Piece Piece
5 hp (3.7 kW) Motor, 50 Hertz**
Low Voltage:
42579 43269 43271 10.104 43330 10.106 43267 10.110
200, 220, 230
High Voltage:
42579 43269 43271 10.104 43331 10.106 43267 10.110
380, 415
5 hp (3.7 kW) Motor, 60 Hertz
Low Voltage:
42580 43269 43271 10.104 43330 10.106 43267 10.110
200, 208
Low Voltage:
42579 43269 43271 10.104 43330 10.106 43267 10.110
220, 230, 240
High Voltage:
42581 43269 43271 10.104 43331 10.106 43267 10.110
380
High Voltage:
42579 43269 43271 10.104 43331 10.106 43267 10.110
460

CE Compliant, Electrical Enclosure Assemblies with VFD

Voltage Motor Electrical Assembly Electrical Enclosure Electrical Schematic
Part Number Assembly
Part Feed/Discharge* Page Part Page Part Page
Number One Two Number Number Number Number Number
Piece Piece
5 hp (3.7 kW) Motor, 50 Hertz
380, 400, 415 42579 43269 43271 10.114 43329 10.116 43278 10.120

* The Feed Cover (1) is available with the discharge chute (2) integrated into a one-piece unit or with a separate
discharge chute (3) attached to the support housing (two piece). These feed covers have different safety switch
arrangements and require corresponding electrical assemblies.
** Not CE compliant. See the lower chart for CE compliant assemblies.
One Piece Two Piece
Feed/Discharge Feed/Discharge

10 3
 Parts: Electrical Assembly Charts 10.103

Electrical Enclosure Assemblies with Soft Start

Voltage Motor Electrical Assembly Electrical Enclosure Electrical Schematic
Part Number Assembly
Part Feed/Discharge* Page Part Page Part Page
Number One Two Number Number Number Number Number
Piece Piece
5 hp (3.7 kW) Motor, 50 Hertz**
Low Voltage:
42579 43269 43271 10.124 43328 10.126 43281 10.130
200, 220, 230,240
High Voltage:
42579 43269 43271 10.124 43333 10.126 43281 10.130
380, 400, 415
10 hp (7.5 kW) Motor, 50 Hertz**
Low Voltage:
42332 43269 43271 10.124 43328 10.126 43281 10.130
200, 220, 230, 240
High Voltage:
42332 43269 43271 10.124 43328 10.126 43281 10.130
380, 415
5 hp (3.7 kW) Motor, 60 Hertz
Low Voltage
42580 43269 43271 10.124 43328 10.126 43281 10.130
200, 208
Low Voltage
42579 43269 43271 10.124 43328 10.126 43281 10.130
220, 230, 240
High Voltage:
42581 43269 43271 10.124 43333 10.126 43281 10.130
380
High Voltage:
42579 43269 43271 10.124 43333 10.126 43281 10.130
460
High Voltage:
42582 43269 43271 10.124 43333 10.126 43281 10.130
575
10 hp (7.5 kW) Motor, 60 Hertz
Low Voltage:
42332 43269 43271 10.124 43328 10.126 43281 10.130
220, 230, 240
High Voltage:
42334 43269 43271 10.124 43328 10.126 43281 10.130
380
High Voltage:
42332 43269 43271 10.124 43328 10.126 43281 10.130
460
High Voltage:
42335 43269 43271 10.124 43333 10.126 43281 10.130
575

* See the footnote on the previous page.

** The 50 hertz soft start assemblies listed in the chart are CE compliant.

10
 10.104 Parts: Electrical Assembly, with VFD, low/high voltage

The electrical assembly is

supplied with either mini
circuit breakers or fuses.

10
 Parts: Electrical Assembly, with VFD, low/high voltage 10.105

Item Quantity Part Number and Description

– 1 43269 - Electrical Assembly*, DCA, one piece feed/discharge (includes items 1–4)
1 43271 - Electrical Assembly*, DCA, two piece feed/discharge (includes items 1–4)
1 1 11593 - Breather/Drain, 1/4"
2 1 13408 - Padlock with Chain
3 1 21499 - Split Ring, s.s.
4 1 21778 - Padlock Retainer
– 1 43330 - Electrical Enclosure Assembly**, DCA, with VFD, low voltage (includes items 5–9)
1 43331 - Electrical Enclosure Assembly**, DCA, with VFD, high voltage (includes items 5–7
and circuit breakers or fuses listed below, see items 10–15)
5 1 *** - Control Circuit Transformer, 50 VA (T1)
6 4 10625 - Round Head Machine Screw, with washer, 10-32 x 1/2"
7 1 21618 - Circuit Breaker, mini, 1 pole, 3 amp (MCB3)
8 1 21613 - Circuit Breaker, mini, 2 pole, 1 amp (MCB2)
9 1 21610 - Circuit Breaker, mini, 3 pole, 30 amp (MCB1)

Overcurrent Protection Device (OCPD), choose circuit breakers (items 10–11) or fuses (items 12–15)
10 1 *** - Circuit Breaker, mini, 3 pole (MCB1)
11 1 *** - Circuit Breaker, mini, 2 pole (MCB2)
12 3 *** - Fuse, cube (FU1)
13 3 21349 - Fuse Base, 30 amp, cube (for FU1)
14 2 *** - Fuse (FU2)
15 1 12930 - Modular Fuse Holder, 2 pole (for FU2)

* See Guard Lock Switches, two piece on page 10.134, Guard Lock Switches, one piece on page 10.136, and
Enclosure Fittings on page 10.140 for additional parts in this assembly.
** Electrical enclosure assembly parts list continues on the following pages.
*** See Overcurrent Protection Device (OCPD) in the chart below.

5 hp (3.7 kW) Motor, VFD

Voltage Motor Electrical Electrical Item 5 Overcurrent Protection Device (OCPD)
Assembly Enclosure Control
Mini Circuit Breakers Cube Fuses
Part Number Assembly Circuit
Part Number Part Number
Transformer
(amps) (amps)
Part Feed/Discharge Part Part Item 9, LV Item 8, LV Item 12 Item 14
Number One Two Number Number Item 10, HV Item 11, HV FU1 FU2
Piece Piece MCB1 MCB2
50 Hertz
Low Voltage: 21610 21613
42579 43269 43271 43330 12927 – –
200, 220, 230 (30) (1)
High Voltage: 21608 21612 21327 21919
42579 43269 43271 43331 12928
380, 415 (20) (.5) (20) (.5)
60 Hertz
Low Voltage: 21610 21613
42580 43269 43271 43330 12927 – –
200, 208 (30) (1)
Low Voltage: 21610 21613
42579 43269 43271 43330 12927 – –
220, 230, 240 (30) (1)
High Voltage: 21608 21612 21327 21919
42581 43269 43271 43331 12928
380 (20) (.5) (20) (.5)
High Voltage: 21608 21612 21327 21919
10
42579 43269 43271 43331 12927
460 (20) (.5) (20) (.5)
NOTICE
These assemblies are not CE Compliant, see page 10.114 for CE compliant assemblies.
 10.106 Parts: Electrical Enclosure, with VFD, low/high voltage

The electrical assembly is

supplied with either mini
circuit breakers or fuses.

10
 Parts: Electrical Enclosure, with VFD, low/high voltage 10.107

Item Quantity Part Number and Description

Parts list for these assemblies continued from the previous page
– 1 43330 - Electrical Enclosure Assembly, DCA, with VFD, low voltage (includes items 1–27)
1 43331 - Electrical Enclosure Assembly, DCA, with VFD, high voltage (includes items 1–27)
1 1 43327 - Electrical Enclosure, DCA with VFD (includes latches, gaskets and windows,
see the following page)
2 2 21557 - Disconnect Switch, 3 pole, 40 amp (DISC1 and DISC2)
3 1 12943 - Auxiliary Contact, normally open (for DISC2)
4 1 21559 - Disconnect Shaft, extended, 10.4" long (for DISC2)
5 1 * - Variable Frequency Drive (VFD1, includes item 6)
6 1 21655 - Digital Operator, V1000
7 4 10415 - Round Head Machine Screw, with washer, 8-32 x 1/2"
8 1 21781 - Control Relay, 2 normally open, 2 normally closed, 24 volt (CR1)
9 1 21676 - Front Mount Auxiliary Contact, 2 normally open (for CR1)
10 4 21926 - Control Relay Socket, PCB, 2 changeover contacts (CR2, CR3, CR4 and CR5)
11 4 21927 - Control Relay, PCB, 2 form C (for CR2, CR3, CR4 and CR5)
12 4 21928 - Control Relay Function, LED, green 24 VAC (for CR2, CR3, CR4 and CR5)
13 1 21515 - Standstill Monitor, PILZ/PSWZ (SSM1)
14 1 21883 - Safety Relay, SCR-31-i, Viper (SR1)
15 3 21678 - Terminal Block, IEC, #18-6 AWG
16 18 21673 - Terminal Block, 4 spring clamp, 2 circuits
17 3 21861 - Terminal End Section, 2 circuit, 4 connection point (for 21673)
18 5 21875 - Jumper Bar, 2 pole, for 21673
19 11 21943 - Terminal Block, 6 spring clamp, 1 circuit
20 1 21944 - Terminal End Section, 6 connection point (for 21943)
21 1 21908 - Jumper Bar, 3 pole, for 21673 (used with 21943)
22 2 21875 - Jumper Bar, 2 pole, for 21673 (used with 21943)
23 3 21439 - End Anchor
24 7 21442 - Grounding Block, size 4
25 2 21443 - Grounding Block, size 10
26 1 43275 - Electrical Enclosure Panel, DCA
27 1 43267 - Electrical Schematic, DCA, with VFD, without CE
28 1 43288 - VFD Chart, MDCA (see VFD constant chart below)

* See variable frequency drive chart below.

The Electrical Schematic is illustrated on the following pages.

Optional meter to track operating hours

29 1 21894 - Hour Meter, 24 VAC (HM)

Parts list for these assemblies continues on the following pages.

Item 5
Variable Frequency Drive (VFD) Chart
Voltage VFD Part Number
200-240 21524
380-460 21525

10
 10.108 Parts: Electrical Enclosure, with VFD (Door Parts), low/high voltage

10
Parts: Electrical Enclosure, with VFD (Door Parts), low/high voltage 10.109

Item Quantity Part Number and Description

Parts list for these assemblies continued from the previous page.
– 1 43330 - Electrical Enclosure Assembly, DCA, with VFD, low voltage (includes items 1–28)
1 43331 - Electrical Enclosure Assembly, DCA, with VFD, high voltage (includes items 1–28)
1 1 21560 - Disconnect Switch Handle (includes O-ring)
2 1 21460 - Disconnect Rod Guide
– 1 21763 - Push Button Assembly, E-Stop, 2 normally closed (includes items 3–7)
3 1 21427 - Push Button, E-Stop, red, 40 mm
4 2 21429 - Contact Block, normally closed, with latch
5 1 21428 - Legend Plate, yellow, round
6 1 21578 - Washer, push button, anti-rotation
7 1 21572 - Push Button Nut, metal
– 1 21424 - Push Button Assembly, start (includes items 8–11)
8 1 21425 - Push Button, start
9 1 21430 - Contact Block, normally open, with latch
10 1 21572 - Push Button Nut, metal
11 1 21431 - Boot, push button
– 1 21723 - Push Button Assembly, stop, standard (includes items 12–15)
12 1 21487 - Push Button, stop
13 1 21429 - Contact Block, normally closed, with latch
14 1 21572 - Push Button Nut, metal
15 1 21721 - Boot, extended, push button, A-B
– 1 21648 - Pilot Light Assembly, 24 volt, green (includes items 16–19)
16 1 21434 - Pilot Light, lens, green
17 1 21491 - Pilot Light, Lamp, green, 24 VAC/VDC
18 1 21432 - Latch, push button
19 1 21572 - Push Button Nut, metal
– 1 21622 - Push Button Assembly, reset (includes items 20–23)
20 1 21623 - Push Button, reset
21 1 21430 - Contact Block, normally open, with latch
22 1 21572 - Push Button Nut, metal
23 1 21431 - Boot, push button
24 1 49637 - Potentiometer, 2500 Ohms
25 1 49638 - Legend Plate, graduated markings
– 1 43327 - Electrical Enclosure, DCA with VFD (includes items 26–28)
26 1 * - Door Gasket (fitting and adhesive required)
27 4 43339 - Latch, quarter turn, 7mm triangle, s.s.
28 4 74009 - Gasket for 1/4 Turn Latches
29 1 43338 - Key, 7 mm triangle

* Contact an Urschel representative.

10
 10.110 Parts: Electrical Schematic 43267, with VFD, without CE

10
Parts: Electrical Schematic 43267, with VFD, without CE 10.111

10
 10.112 Parts: Electrical Schematic 43267, with VFD

10
Parts: Electrical Schematic 43267, with VFD 10.113

10
 10.114 Parts: Electrical Assembly, with VFD, CE Compliant

10
 Parts: Electrical Assembly, with VFD, CE Compliant 10.115

Item Quantity Part Number and Description

– 1 43269 - Electrical Assembly*, DCA, one piece feed/discharge (includes items 1–4)
1 43271 - Electrical Assembly*, DCA, two piece feed/discharge (includes items 1–4)
1 1 11593 - Breather/Drain, 1/4"
2 1 13408 - Padlock with Chain
3 1 21499 - Split Ring, s.s.
4 1 21778 - Padlock Retainer
5 1 43329 - Electrical Enclosure Assembly**, DCA, with VFD, CE

* See Guard Lock Switches, two piece on page 10.134, Guard Lock Switches, one piece on page 10.136, and
Enclosure Fittings on page 10.140 for additional parts in this assembly.
** Electrical enclosure assembly parts list begins on the following page.

5 hp (3.7 kW) Motor, 50 Hertz, CE Compliant,

Electrical Enclosure Assemblies with VFD
Voltage Motor Electrical Electrical Electrical
Assembly Enclosure Schematic
Part Number Assembly
Part Feed/Discharge* Part Part
Number One Two Number Number
Piece Piece

380, 400, 415 42579 43269 43271 43329 43278

10
 10.116 Parts: Electrical Enclosure, with VFD, CE Compliant

10
 Parts: Electrical Enclosure, with VFD, CE Compliant 10.117

Item Quantity Part Number and Description

– 1 43329 - Electrical Enclosure Assembly, DCA, with VFD, CE (includes items 1–36)
1 1 43327 - Electrical Enclosure, DCA with VFD (includes latches, gaskets and windows,
see the following page)
2 2 21557 - Disconnect Switch, 3 pole, 40 amp (DISC1 and DISC2)
3 1 12943 - Auxiliary Contact, normally open (for DISC2)
4 1 21559 - Disconnect Shaft, extended, 10.4" long (for DISC2)
5 1 21242 - Power Line Filter, 16 amp, 3 phase
6 8 10415 - Round Head Machine Screw, with washer, 8-32 x 1/2"
7 1 21525 - Variable Frequency Drive, 460 volt, 9.2 amp (VFD1, includes item 8)
8 1 21655 - Digital Operator, V1000
9 4 10415 - Round Head Machine Screw, with washer, 8-32 x 1/2"
10 1 12813 - Ferrite
11 1 10415 - Round Head Machine Screw, with washer, 8-32 x 1/2"
12 1 12928 - Control Circuit Transformer, 50 VA (T1)
13 4 10625 - Round Head Machine Screw, with washer, 10-32 x 1/2"
14 1 21781 - Control Relay, 2 normally open, 2 normally closed, 24 volt (CR1)
15 1 21676 - Front Mount Auxiliary Contact, 2 normally open (for CR1)
16 4 21926 - Control Relay Socket, PCB, 2 changeover contacts (CR2, CR3, CR4 and CR5)
17 4 21927 - Control Relay, PCB, 2 form C (for CR2, CR3, CR4 and CR5)
18 4 21928 - Control Relay Function, LED, green 24 VAC (for CR2, CR3, CR4 and CR5)
19 1 21515 - Standstill Monitor, PILZ/PSWZ (SSM1)
20 1 21883 - Safety Relay, SCR-31-i, Viper (SR1)
21 1 21608 - Circuit Breaker, mini, 3 pole, 20 amp (MCB1)
22 1 21612 - Circuit Breaker, mini, 2 pole, 50 amp (MCB2)
23 1 21618 - Circuit Breaker, mini, 1 pole, 3 amp (MCB3)
24 3 21678 - Terminal Block, IEC, #18-6 AWG
25 18 21673 - Terminal Block, 4 spring clamp, 2 circuits
26 3 21861 - Terminal End Section, 2 circuit, 4 connection point (for 21673)
27 5 21875 - Jumper Bar, 2 pole, for 21673
28 11 21943 - Terminal Block, 6 spring clamp, 1 circuit
29 1 21944 - Terminal End Section, 6 connection point (for 21943)
30 1 21908 - Jumper Bar, 3 pole, for 21673 (used with 21943)
31 2 21875 - Jumper Bar, 2 pole, for 21673 (used with 21943)
32 3 21439 - End Anchor
33 7 21442 - Grounding Block, size 4
34 2 21443 - Grounding Block, size 10
35 1 43275 - Electrical Enclosure Panel, DCA
36 1 43278 - Electrical Schematic, DCA, with VFD, CE
37 1 43288 - VFD Chart, MDCA (see VFD constant chart)

The Electrical Schematic is illustrated on the following pages.

Optional meter to track operating hours

38 1 21894 - Hour Meter, 24 VAC (HM)

Parts list for these assemblies continues on the following pages.

10
 10.118 Parts: Electrical Enclosure, with VFD, CE Compliant (Door Parts)

10
 Parts: Electrical Enclosure, with VFD, CE Compliant (Door Parts) 10.119

Item Quantity Part Number and Description

Parts for this assembly continued from the previous page.
– 1 43329 - Electrical Enclosure Assembly, DCA, with VFD, CE (includes items 1–28)
1 1 21560 - Disconnect Switch Handle (includes O-ring)
2 1 21460 - Disconnect Rod Guide
– 1 21763 - Push Button Assembly, E-Stop, 2 normally closed (includes items 3–7)
3 1 21427 - Push Button, E-Stop, red, 40 mm
4 2 21429 - Contact Block, normally closed, with latch
5 1 21428 - Legend Plate, yellow, round
6 1 21578 - Washer, push button, anti-rotation
7 1 21572 - Push Button Nut, metal
– 1 21424 - Push Button Assembly, start (includes items 8–11)
8 1 21425 - Push Button, start
9 1 21430 - Contact Block, normally open, with latch
10 1 21572 - Push Button Nut, metal
11 1 21431 - Boot, push button
– 1 21723 - Push Button Assembly, stop, standard (includes items 12–15)
12 1 21487 - Push Button, stop
13 1 21429 - Contact Block, normally closed, with latch
14 1 21572 - Push Button Nut, metal
15 1 21721 - Boot, extended, push button, A-B
– 1 21648 - Pilot Light Assembly, 24 volt, green (includes items 16–19)
16 1 21434 - Pilot Light, lens, green
17 1 21491 - Pilot Light, Lamp, green, 24 VAC/VDC
18 1 21432 - Latch, push button
19 1 21572 - Push Button Nut, metal
– 1 21622 - Push Button Assembly, reset (includes items 20–23)
20 1 21623 - Push Button, reset
21 1 21430 - Contact Block, normally open, with latch
22 1 21572 - Push Button Nut, metal
23 1 21431 - Boot, push button
24 1 49637 - Potentiometer, 2500 Ohms
25 1 49638 - Legend Plate, graduated markings
– 1 43327 - Electrical Enclosure, DCA with VFD (includes items 26–28)
26 1 * - Door Gasket (fitting and adhesive required)
27 4 43339 - Latch, quarter turn, 7mm triangle, s.s.
28 4 74009 - Gasket for 1/4 Turn Latches
29 1 43338 - Key, 7 mm triangle

* Contact an Urschel representative.

10
 10.120 Parts: Electrical Schematic 43278, with VFD, CE Compliant

10
Parts: Electrical Schematic 43278, with VFD, CE Compliant 10.121

10
 10.122 Parts: Electrical Schematic 43278, with VFD, CE Compliant

10
Parts: Electrical Schematic 43278, with VFD, CE Compliant 10.123

10
 10.124 Parts: Electrical Assembly, with Soft Start

The electrical assembly is

supplied with either mini
circuit breakers or fuses.

10
 Parts: Electrical Assembly, with Soft Start 10.125

Item Quantity Part Number and Description

– 1 43269 - Electrical Assembly*, DCA, one piece feed/discharge (includes items 1–4)
1 43271 - Electrical Assembly*, DCA, two piece feed/discharge (includes items 1–4)
1 1 11593 - Breather/Drain, 1/4"
2 1 13408 - Padlock With Chain
3 1 21499 - Split Ring, s.s.
4 1 21778 - Padlock Retainer
– 1 43328 - Electrical Enclosure Assembly**, DCA, with soft start, 37 Amp (includes items 5–7)
1 43333 - Electrical Enclosure Assembly**, DCA, with soft start, 16 Amp (includes items 5–7 and
circuit breakers or fuses listed below, see items 8–13)
5 1 *** - Control Circuit Transformer, 50 VA (T1)
6 4 10625 - Round Head Machine Screw, with washer, 10-32 x 1/2"
7 1 21618 - Circuit Breaker, mini, 1 pole, 3 amp

Overcurrent Protection Device (OCPD), choose circuit breakers (items 8–9) or fuses (items 10–13).
8 1 *** - Circuit Breaker, mini, 3 pole (MCB1)
9 1 *** - Circuit Breaker, mini, 2 pole (MCB2)
10 3 *** - Fuse, cube (FU1)
11 3 21349 - Fuse Base, 30 amp, cube (for FU1)
12 2 *** - Fuse (FU2)
13 1 12930 - Modular Fuse Holder, 2 pole (for FU2)

* See Guard Lock Switches, two piece on page 10.134, Guard Lock Switches, one piece on page 10.136, and
Enclosure Fittings on page 10.140 for additional parts in this assembly.
** Electrical enclosure assembly parts list continues on the following pages.
*** See Overcurrent Protection Device (OCPD) in the chart below.
Voltage Motor Electrical Electrical Item 5 Overcurrent Protection Device (OCPD)
Assembly Enclosure Control Circuit Mini Circuit Breakers Cube Fuses
Part Number Assembly Transformer Part Number (amps) Part Number (amps)
Part Feed/Discharge Part Part Item 8 Item 9 Item 10 Item 12
Number One Two Number Number MCB1 MCB2 FU1 FU2
Piece Piece
5 hp (3.7 kW) Motor, 50 Hertz (CE Compliant)
200 42579 43269 43271 43328 12927 21610 (30) 21613 (1) – –
220, 230 42579 43269 43271 43328 12927 21609 (25) 21613 (1) – –
240 42579 – 43271 43328 12927 21609 (25) 21613 (1) – –
380, 415 42579 43269 43271 43333 12928 21607 (15) 21612 (.5) 21325 (15) 21919 (.5)
10 hp (7.5 kW) Motor, 50 Hertz (CE Compliant)
200 42332 43269 43271 43328 12927 – – 21335 (60) 12693 (1)
220, 230 42332 43269 43271 43328 12927 – – 21333 (50) 12693 (1)
240 42332 – 43271 43328 12927 – – 21332 (45) 12693 (1)
380 42332 43269 43271 43328 12928 21610 (30) 21612 (.5) 21329 (30) 21919 (.5)
415 42332 43269 43271 43328 12928 21609 (25) 21612 (.5) 21328 (25) 21919 (.5)
5 hp (3.7 kW) Motor, 60 Hertz
200, 208 42580 – 43271 43328 12927 21609 (25) 21613 (1) – –
220 42579 43269 43271 43328 12927 21610 (30) 21613 (1) – –
230, 240 42579 43269 43271 43328 12927 21609 (25) 21613 (1) – –
380 42581 43269 43271 43333 12928 21607 (15) 21612 (.5) 21325 (15) 21919 (.5)
460 42579 43269 43271 43333 12927 21607 (15) 21612 (.5) 21325 (15) 21919 (.5)
575 42582 43269 43271 43333 12310 – – 21339 (10) 21509 (4/10)
10 hp (7.5 kW) Motor, 60 Hertz
220 42332 43269 43271 43328 12927 – – 21333 (50) 12693 (1) 10
230, 240 42332 43269 43271 43328 12927 – – 21332 (45) 12693 (1)
380 42334 43269 43271 43328 12928 21610 (30) 21612 (.5) 21329 (30) 21919 (.5)
460 42332 43269 43271 43328 12927 21609 (25) 21612 (.5) 21328 (25) 21919 (.5)
575 42335 43269 43271 43333 12310 – – 21327 (20) 21509 (4/10)
 10.126 Parts: Electrical Enclosure, with Soft Start

The electrical assembly is

supplied with either mini
circuit breakers or fuses.

10
 Parts: Electrical Enclosure, with Soft Start 10.127

Item Quantity Part Number and Description

Parts list for these assemblies continued from the previous page.
– 1 43328 - Electrical Enclosure Assembly, DCA, with soft start, 37 Amp (includes items 2–28)
1 43333 - Electrical Enclosure Assembly, DCA, with soft start, 16 Amp (includes items 2–28)
1 1 43326 - Electrical Enclosure, DCA with soft start (includes latches, gaskets and windows,
see the following page)
2 2 21557 - Disconnect Switch, 3 pole, 40 amp (DISC1 and DISC2)
3 1 12943 - Auxiliary Contact, normally open (for DISC2)
4 1 21559 - Disconnect Shaft, extended, 10.4" long (for DISC2)
5 1 21837 - Contactor, 50 amp, 24 volt 50/60 Hz coil (M1)
6 2 21839 - Auxiliary Contact Block, front mount, normally open (for M1)
7 1 21840 - Auxiliary Contact Block, front mount, normally closed (for M1)
8 3 21926 - Control Relay Socket, PCB, 2 changeover contacts (CR1, CR2, and CR3)
9 3 21927 - Control Relay, PCB, 2 form C (for CR1, CR2, and CR3)
10 3 21928 - Control Relay Function, LED, green 24 VAC (for CR1, CR2, and CR3)
11 1 21596 - Soft Start Controller, 37 amp (SST1)
1 21668 - Soft Start Controller, 16 amp, 24 volt (SST1)
12 1 21601 - Soft Start Overload Reset Solenoid (for SST1)
13 1 21515 - Standstill Monitor, PILZ/PSWZ (SSM1)
14 1 21883 - Safety Relay, SCR-31-i, Viper (SR1)
15 1 21618 - Circuit Breaker, mini, 1 pole, 3 amp (MCB3)
16 3 21438 - Terminal Block, IEC, #22-10 AWG
17 18 21673 - Terminal Block, 4 spring clamp, 2 circuits
18 3 21861 - Terminal End Section, 2 circuit, 4 connection point (for 21673)
19 5 21875 - Jumper Bar, 2 pole, for 21673
20 9 21943 - Terminal Block, 6 spring clamp, 1 circuit
21 1 21944 - Terminal End Section, 6 connection point (for 21943)
22 1 21908 - Jumper Bar, 3 pole, for 21673 (use with 21943)
23 1 21875 - Jumper Bar, 2 pole, for 21673 (use with 21943)
24 5 21439 - End Anchor
25 7 21442 - Grounding Block, size 4
26 2 21443 - Grounding Block, size 10
27 1 43275 - Electrical Enclosure Panel, DCA
28 1 43281 - Electrical Schematic, DCA, with soft start
29 1 43289 - Soft Start Chart, MDCA (see the soft start dip switch chart below)

The Electrical Schematic is illustrated on the following pages.

Optional meter to track operating hours

30 1 21894 - Hour Meter, 24 VAC (HM)

Parts list for these assemblies continues on the following pages.

10
 10.128 Parts: Electrical Enclosure, with Soft Start (Door Parts)

10
 Parts: Electrical Enclosure, with Soft Start (Door Parts) 10.129

Item Quantity Part Number and Description

Parts list for these assemblies continued from the previous page.
– 1 43328 - Electrical Enclosure Assembly, DCA, 37 Amp (includes items 1–26)
1 43333 - Electrical Enclosure Assembly, DCA, 16 Amp (includes items 1–26)
1 1 21560 - Disconnect Switch Handle (includes O-ring)
2 1 21460 - Disconnect Rod Guide
– 1 21763 - Push Button Assembly, E-Stop, 2 normally closed (includes items 3–7)
3 1 21427 - Push Button, E-Stop, red, 40 mm
4 2 21429 - Contact Block, normally closed, with latch
5 1 21428 - Legend Plate, yellow, round
6 1 21578 - Washer, push button, anti-rotation
7 1 21572 - Push Button Nut, metal
– 1 21424 - Push Button Assembly, start (includes items 8–11)
8 1 21425 - Push Button, start
9 1 21430 - Contact Block, normally open, with latch
10 1 21572 - Push Button Nut, metal
11 1 21431 - Boot, push button
– 1 21723 - Push Button Assembly, stop, standard (includes items 12–15)
12 1 21487 - Push Button, stop
13 1 21429 - Contact Block, normally closed, with latch
14 1 21572 - Push Button Nut, metal
15 1 21721 - Boot, extended, push button, A-B
– 1 21648 - Pilot Light Assembly, 24 volt, green (includes items 16–19)
16 1 21434 - Pilot Light, lens, green
17 1 21491 - Pilot Light, Lamp, green, 24 VAC/VDC
18 1 21432 - Latch, push button
19 1 21572 - Push Button Nut, metal
– 1 21622 - Push Button Assembly, reset (includes items 20–23)
20 1 21623 - Push Button, reset
21 1 21430 - Contact Block, normally open, with latch
22 1 21572 - Push Button Nut, metal
23 1 21431 - Boot, push button
– 1 43326 - Electrical Enclosure, DCA with soft start (includes items 24–26)
24 1 * - Door Gasket (fitting and adhesive required)
25 4 43339 - Latch, quarter turn, 7mm triangle, s.s.
26 4 74009 - Gasket for 1/4 Turn Latches
27 1 43338 - Key, 7 mm triangle

* Contact an Urschel representative.

10
 10.130 Parts: Electrical Schematic 43281, with Soft Start

10
Parts: Electrical Schematic 43281, with Soft Start 10.131

10
 10.132 Parts: Electrical Schematic 43281, with Soft Start

10
Parts: Electrical Schematic 43281, with Soft Start 10.133

10
 10.134 Parts: Guard Locking Switches, two piece feed/discharge

10
 Parts: Guard Locking Switches, two piece feed/discharge 10.135

Item Quantity Part Number and Description

– 1 43271 - Electrical Assembly, DCA, two piece feed/discharge (includes items 1–23)
1 1 21784 - Sensor, 24 VAC, dual channel (includes sensor and actuator)
2 1 12482 - Actuator, 24 VAC, dual channel (actuator only, for repairs)
– 1 42309 - Guard Lock Switch, assembled, DC 1 (includes items 3–12)
3 2 10006 - Washer, flat, #10, s.s., thin
4 2 10232 - Hex Head Cap Screw, 10-24 x 5/8", s.s.
5 1 21419 - Cord Connector, straight, .276"/.512"
6 1 21351 - O-ring, 1/16" x 11/16" x 13/16", Viton
7 2 55245 - Screw, titan switch
8 2 21274 - Button Head Screw, T25 Torx, 10-24 x 7/8"
2 21357 - Button Head Screw, T25 Torx, 10-24 x 1" (only if spacer is used)
9 1 21420 - Guard Locking Switch (includes items 10–11)
10 1 21811 - Cover, guard lock switch, A-B
11 1 12983 - Guard Locking Switch, flexible actuator
12 2 10231 - Hex Nut, 10-24, s.s., locking
– 1 42310 - Guard Lock Switch, assembled, DC 2 (includes items 13–23)
13 6 10006 - Washer, flat, #10, s.s., thin
14 2 10351 - Hex Head Cap Screw, 10-24 x 7/8", s.s.
15 4 10231 - Hex Nut, 10-24, s.s., locking
16 1 21419 - Cord Connector, straight, .276"/.512"
17 1 21351 - O-ring, 1/16" x 11/16" x 13/16", Viton
18 2 42483 - Screw, titan switch
19 2 21274 - Button Head Screw, T25 Torx, 10-24 x 7/8"
20 1 21420 - Guard Locking Switch (includes items 21–22)
21 1 21811 - Cover, guard lock switch, A-B
22 1 12983 - Guard Locking Switch, flexible actuator
23 16 11534 - Cable Tie
– 1 43335 - Electrical Assembly, machine, DCA, two-piece feed/discharge (includes items 24–31)
24 2 10232 - Hex Screw
25 4 10231 - Hex Nut, 10-24, s.s., locking
26 2 10433 - Flat Head Cap Screw, 10-24 x 1/2", s.s., undercut
27 1 21416 - Spacer, 1/8" (3.2 mm), for magnetic sensor
28 5 10236 - Hex Head Cap Screw, 1/4-20 3/8", s.s.
29 5 42668 - Loop Strap, rubber cushion, for 1/2" O.D.
30 16 11513 - Cable Tie
31 16 13465 - Cable Tie Clip
32 1 53391 - Spacer, 3/32" (2.4 mm)
33 1 42238 - Handle, knob
34 1 42239 - Handle, latch

Optional spacers used to properly position the switch parts, use as needed
– 1 21512 - Spacer, 1/4" (6.4 mm), magnetic sensor (replaces item 27)
1 21513 - Spacer, 3/8" (9.5 mm), magnetic sensor (replaces item 27)
1 21514 - Spacer, 1/2" (12.7 mm), magnetic sensor (replaces item 27)
– 1 53390 - Spacer, 1/16" (1.6 mm) (replaces item 32)
1 53392 - Spacer, 1/8" (3.2 mm) (replaces item 32)

Additional parts for 43271 assembly are shown on page 10.140.

10
 10.136 Parts: Guard Locking Switches, one piece feed/discharge

10
 Parts: Guard Locking Switches, one piece feed/discharge 10.137

Item Quantity Part Number and Description

– 1 43269 - Electrical Assembly, DCA, one piece feed/discharge (includes items 1–23)
1 1 21784 - Sensor, 24 VAC, dual channel (includes sensor and actuator)
2 1 12482 - Actuator, 24 VAC, dual channel (actuator only, for repairs)
– 1 42513 - Guard Lock Switch, assembled, DC 1 (includes items 3–12)
3 2 10006 - Washer, flat, #10, s.s., thin
4 2 10232 - Hex Head Cap Screw, 10-24 x 5/8", s.s.
5 1 21419 - Cord Connector, straight, .276"/.512"
6 1 21351 - O-ring, 1/16" x 11/16" x 13/16", Viton
7 2 55245 - Screw, Titan switch
8 2 21357 - Button Head Screw, T25 Torx, 10-24 x 1"
9 1 21420 - Guard Locking Switch (includes items 10–11)
10 1 21811 - Cover, guard lock switch, A-B
11 1 12983 - Guard Locking Switch, flexible actuator
12 2 10231 - Hex Nut, 10-24, s.s., locking
– 1 42310 - Guard Lock Switch, assembled, DC 2 (includes items 13–22)
13 6 10006 - Washer, flat, #10, s.s., thin
14 2 10351 - Hex Head Cap Screw, 10-24 x 7/8", s.s.
15 4 10231 - Hex Nut, 10-24, s.s., locking
16 1 21419 - Cord Connector, straight, .276"/.512"
17 1 21351 - O-ring, 1/16" x 11/16" x 13/16", Viton
18 2 42483 - Screw, titan switch
19 2 21274 - Button Head Screw, T25 Torx, 10-24 x 7/8"
20 1 21420 - Guard Locking Switch
21 1 21811 - Cover, guard lock switch, A-B
22 1 12983 - Guard Locking Switch, flexible actuator
23 16 11534 - Cable Tie
– 1 43334 - Electrical Assembly, Machine, DCA, one-piece feed/discharge (includes items 24–32)
24 2 10008 - Washer, flat, 5/16", s.s., thick
25 2 10045 - Hex Head Cap Screw, 5/16-18 x 3/4", s.s.
26 4 10231 - Hex Nut, 10-24, s.s., locking
27 2 10232 - Hex Head Cap Screw, 10-24 x 5/8", s.s.
28 2 10433 - Flat Head Cap Screw, 10-24 x 1/2", s.s., undercut
29 1 21416 - Spacer, 1/8" (3.2 mm), for magnetic sensor
30 1 42519 - Bracket, guard-lock
31 16 11513 - Cable Tie
32 16 13465 - Cable Tie Clip
33 1 53391 - Spacer, 3/32" (2.4 mm)
34 1 42238 - Handle, knob
35 1 42239 - Handle, latch

Optional spacers used to properly position the switch parts, use as needed
– 1 21512 - Spacer, 1/4" (6.4 mm), magnetic sensor (replaces item 31)
1 21513 - Spacer, 3/8" (9.5 mm), magnetic sensor (replaces item 31)
1 21514 - Spacer, 1/2" (12.7 mm), magnetic sensor (replaces item 31)
– 1 53390 - Spacer, 1/16" (1.6 mm) (replaces item 33)
1 53392 - Spacer, 1/8" (3.2 mm) (replaces item 33)

Additional parts for 43269 assembly are shown on page 10.140.

10
 10.138 Parts: Guard Locking Switch for a Collection Device

24

10
 Parts: Guard Locking Switch for a Collection Device 10.139

Item Quantity Part Number and Description

– 1 43291 - Electrical Assembly*, DCA, GLS3 (includes items 1–21)
1 1 11877 - Cord Connector, straight, .236"/.472"
2 1 11900 - Seal Washer, 3/16" x 7/8" x 1-9/32"
3 1 11611 - Lock Nut, 1/2"
4 1 43290 - Guard Lock Switch, assembled DC3 (includes items 5–11)
5 1 21420 - Guard Locking Switch (includes item 6)
6 1 21811 - Cover, guard lock switch, A-B
7 2 10006 - Washer, flat, #10, s.s., thin
8 2 10232 - Hex Head Cap Screw, 10-24 x 5/8", s.s.
9 2 55245 - Screw, Titan switch
10 1 21419 - Cord Connector, straight, .276"/.512"
11 1 21351 - O-ring, 1/16" x 11/16" x 13/16", Viton
– 1 43292 - Electrical Assembly*, machine, DCA, GLS3 (includes items 12–21)
12 1 34213 - Standard Actuator, Titan
13 2 10155 - Flat Head Screw, 10-24 x 5/8", s.s.
14 2 10231 - Hex Nut, 10-24, s.s., locking
15 2 34199 - Bracket, key and shackle, conveyor interlock
16 1 34212 - Shackle, guard lock switch (includes hardware)
17 1 34211 - Chain, guard lock switch
18 1 42297 - Label, guard locking switch
19 1 98250 - Special Machine Plate
20 3 21474 - Wire Tie Clip, 1 wire
21 3 11513 - Cable Tie
22 1 ** - Warning Label, release tool
23 1 43296 - Floor Stand, 15" height (381 mm), wide, guard lock
1 43295 - Floor Stand, 15" height (381 mm), casters, wide, guard lock
24 1 43323§ - Feed Cover/Discharge, wide, no bars
– 1 43314§ - Discharge Chute, small dice, no bars (not shown, use with 43203 feed cover)

* See the Instruction manual, Section 3 Installation: Installation Information for a Machine with Special Parts for
additional information.
** See Safety Signs and Machine Labels for available languages.
§
See Important message and Warning below.

The assemblies and parts listed above are used with 43269 or 43271 electrical assemblies, see pages 10.102-
10.103.

IMPORTANT
A MACHINE EQUIPPED WITH THESE PARTS HAS NO SAFETY BARS IN THE DISCHARGE OPENING.
ADDITIONAL CUSTOMER GUARDING AND/OR INTERLOCKING IS REQUIRED. A CERTIFIED PRINT
SIGNED BY THE CUSTOMER IS REQUIRED FOR MACHINES SOLD WITH THESE PARTS. A Certified Print
(CP) is a document that describes these special parts. A special machine has important installation instructions
included on the Certified Print that are used in addition to or in place of the instructions in the manual. The
installation described on the Certified Print may be required to eliminate or minimize certain risks to persons
operating the machine. Contact your Urschel representative for more information about a machine with special
parts and the Certified Print process.

m WARNING
Failure to properly install and provide safeguards may result in serious injury, amputation or death.
Contact an Urschel representative with any questions concerning the safe installation of the machine.

10
 10.140 Parts: Electrical Enclosure Fittings

10
 Parts: Electrical Enclosure Fittings 10.141

Item Quantity Part Number and Description

– 1 43269 - Electrical Assembly, DCA, one piece feed/discharge (includes items 1–4)
1 43271 - Electrical Assembly, DCA, two piece feed/discharge (includes items 1–4)
1 2 11877 - Cord Connector, straight, .236"/.472"
2 1 11901 - Cord Connector, straight, .190"/.250"
3 3 11900 - Seal Washer, 3/16" x 7/8" x 1-9/32"
4 3 11611 - Lock Nut, 1/2"
– 1 43334 - Electrical Assembly, machine, DCA, one-piece feed/discharge (includes items 5–6)
1 43335 - Electrical Assembly, machine, DCA, two-piece feed/discharge
5 4 10045 - Hex Head Cap Screw, 5/16-18 x 3/4", s.s.
6 4 21982 - Sealing Ring, 1.6mm x 21mm, 17mm

All machines contain the following items 7–12 (not included with the electrical assembly).
7 1 11877 - Cord Connector, straight, .236"/.472"
8 1 11901 - Cord Connector, straight, .190"/.250"
9 2 11611 - Lock Nut, 1/2"
10 2 11956 - Cord Connector, straight, .748"/1.00" (10 HP machines, 200-240 volts only)
2 21563 - Cord Connector, straight, .551"/.827" (5 HP machines, all voltages; 10 HP machines,
380-575 volts only)
11 1 11966 - Seal Washer, 3/16" x 1-5/16" x 1-3/4"
12 1 11957 - Lock Nut, 1" NPT

Items below are not included with the electrical assembly; use at the power source entry point.
13 1 11582 - Conduit Hub, 1" (includes O-ring and lock nut)
– 1 11626 - Cord Connector Assembly, 90 degree, .437"/.562" (includes items 14, 18, 19)
14 1 11625 - Cord Connector, 90 degree, .437"/.562"
– 1 21370 - Cord Connector Assembly, 90 degree, .63"/.75" (includes items 15, 18, 19)
15 1 21368 - Cord Connector, 90 degree, .63"/.75"
– 1 21371 - Cord Connector Assembly, 90 degree, .75"/.88" (includes items 16, 18, 19)
16 1 21369 - Cord Connector, 90 degree, .75"/.88"
– 1 21372 - Cord Connector Assembly, 90 degree, .88"/1.00" (includes items 17, 18, 19)
17 1 11972 - Cord Connector, 90 degree, .88"/1.00"
18 1 11966 - Seal Washer, 3/16" x 1-5/16" x 1-3/4"
19 1 11624 - Lock Nut
20 1 11591 - Hole Seal, 1-3/8"
21 1 10231 - Hex Nut, 10-24, s.s., locking

10
 10.142 Parts: Dimensional Drawing, one piece feed/discharge,
wide discharge

10
Parts: Dimensional Drawing, two piece feed/discharge, 10.143
small dice discharge

10
 10.144 Parts: Center Of Gravity

NOTICE
A machine with a one piece feed/discharge
cover is shown. The center of gravity for a
machine with any standard one or two piece
feed cover and discharge chute is within .5"
(13 mm) of the location shown.

10
This page intentionally left blank.
w w w . u r s c h e l . c o m

CORPORATE HEADQUARTERS
1200 Cutting Edge Drive
Chesterton, Indiana 46304 U.S.A.
Corporate: +1.219.464.4811 Fax: +1.219.462.3879
Toll Free: +1.844.URSCHEL (877.2435)
www.urschel.com
Technical Publication inquiries: [email protected]
Other inquiries: [email protected]
Subsidiaries and sales offices in principal cities worldwide.

The Global Leader in Food Cutting Technology®

Publication Number Publication Description

L3397 MANUAL, ENGLISH, PARTS, DC2110A, 2019 EDITION