Scribd
Upload
23 views

Note 10 en

Uploaded by

Idjosko
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
23 views

Note 10 en

Uploaded by

Idjosko
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 10

Infinix X693

User Manual (F)


Explosion diagram specification

1 (CTP+LCM) 6.95 HD 2 Front cover asm


3 Front cover asm 4 Card holder
5 PCBA MAIN 6 REC
7 CAM FF 2M 8 CAM AF 64M
9 CAM AF 8M 10 CAM FF 2M
11 Rear flash lens 12 Cam support
13 Rear cam deco 14 Cam lens ad
15 Cam lens 16 Screw
M1.4*L3.5*D2.5*H0.5
17 Coaxial cable 18 PCBA SUB
19 Motor 20 Battery
21 SPK 22 FPC MAIN
23 SPK frame asm 24 MIDDLE frame asm
25 Side key fpc 26 Fingerprint module
27 Screw M1.4*L2.5*D2.5*H0.5 28 Battery cover asm

1
Know your phone

1. Front camera
2. Volume + key
3. Volume - key
4. Power key

2
SIM/SD card installation
1. Power off mobile.
2. Refer to the following picture for SIM / SD card
installation.

3
Charging the phone
You can charge your device using a charger or by connecting
it to the computer using a USB cable (comes with the
phone).
1. Please remind the front and back of the plug.
2. Use only INFINIX charger and cables. Other chargers or
cables may damage the device. This will invalidate your
phone warranty.

4
FCC Statement
1.This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including
interference that may cause undesired operation.
2.Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
NOTE:
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:

5
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.`
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

SAR Information Statement


Your wireless phone is a radio transmitter and receiver. It is designed
and manufactured not to exceed the emission limits for exposure to
radiofrequency (RF) energy set by the Federal Communications
Commission of the U.S. Government. These limits are part of
comprehensive guidelines and establish permitted levels of RF energy
for the general population. The guidelines are based on standards that
were developed by independent scientific organizations through
periodic and thorough evaluation of scientific studies. The standards
include a substantial safety margin designed to assure the safety of all
persons, regardless of age and health. The exposure standard for
wireless mobile phones employs a unit of measurement known as the
Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6
W/kg. * Tests for SAR are conducted with the phone transmitting at its
highest certified power level in all tested frequency bands. Although
the SAR is determined at the highest certified power level, the actual
SAR level of the phone while operating can be well below the
maximum value. This is because the phone is designed to operate at
multiple power levels so as to use only the power required to reach
the network. In general, the closer you are to a wireless base station
antenna, the lower the power output. Before a phone model is
available for sale to the public, it must be tested and certified to the
FCC that it does not exceed the limit established by the government
adopted requirement for safe exposure. The tests are performed in
positions and locations (e.g., at the ear and worn on the body) as
required by the FCC for each model. The highest SAR value for this
model phone when tested for use at the ear is 1.156W/Kg and when
worn on the body, as described in this user guide, is
0.580W/Kg(Body-worn measurements differ among phone models,

6
depending upon available accessories and FCC requirements). The
maximum scaled SAR in hotspot mode is 1.184W/Kg. While there may
be differences between the SAR levels of various phones and at
various positions, they all meet the government requirement for safe
exposure. The FCC has granted an Equipment Authorization for this
model phone with all reported SAR levels evaluated as in compliance
with the FCC RFexposure guidelines. SAR information on this model
phone is on file with the FCC and can be found under the Display
Grant section of http://www.fcc.gov/ oet/fccid after searching on
FCC ID: 2AIZN-X693 Additional information on Specific Absorption
Rates (SAR) can be found on the Cellular Telecommunications Industry
Asso-ciation (CTIA) web-site at http://www.wow-com.com. * In the
United States and Canada, the SAR limit for mobile phones used by the
public is 1.6 watts/kg (W/kg) averaged over one gram of tissue. The
standard incorporates a sub-stantial margin of safety to give additional
protection for the public and to account for any variations in
measurements.
Body-worn Operation
This device was tested for typical body-worn operations. To comply
with RF exposure requirements, a minimum separation distance
of 10mm must be maintained between the user’s body and the
handset, including the antenna. Third-party belt-clips, holsters,
and similar accessories used by this device should not contain any
metallic components. Body-worn accessories that do not meet these
requirements may not comply with RF exposure requirements and
should be avoided. Use only the supplied or an approved

7
For DTS patents, see http://patents.dts.com. Manufactured under license
from DTS Licensing Limited. DTS, the Symbol, & DTS and the Symbol
together are registered trademarks or trademarks of DTS, Inc. in the
United States and/or other countries. © DTS, Inc. All Rights Reserved.

Operating System：AndroidTM
Android is a trademark of Google LLC.

You might also like