MAHARASHTRA JEEVAN PRADHIKARAN DIVISION, JALGAON

Name of scheme-Mohide & 25 Villages RRWSS, Dist Nandurbar

Raw water pumping machinery (Zone 1 Stage 2)
ABSTRACT

Qty. Items Rate Unit Amount

In figures
AGREEMENT NO - B1/50 FOR 2022/23
DATE OF WORK ORDER - 25/01/2023
Part A :- Work Completed and Payment
Total A Part 0 Rs. 0.00
Total A Part Rs. 0 Rs. 0.00

AGREEMENT NO - B1/50 FOR 2022/23

DATE OF WORK ORDER - 25/01/2023
Part B :- Balance work and payment (Shedule A
Part)

Item No. 1 A -VT Pump

Providing, erecting and giving satisfactory test and trial of
3.00 VT pump set (Water Lubricated) with following 20,48,395.50 Nos 61,45,186.50
parameters
Discharge = 156100LPH Head =173m
Item No. 1 B - VHS Motor

Providing, erecting and giving test and trial of vertical

hollow shaft motor 1500 RPM, squirrel cage induction
motor, conforming to IS 12615, class IE3 premium, having
continuous rating suitable for operation at 415 Volts +/-
10%, 3 Phase, 50 Hz +/-5% with "F" class insulation
temperature rise limited to class "B" insulation. With TPI
3.00 170 HP VHS Motor 6,49,637.00 Nos 19,48,911.00
Item No. 2 -AT Starter

Providing erecting and giving test and trial of Fully

Automatic, Auto Transformer Starter with Air Break
Contactor, assembled locally with contactors of
approved make in 14 SWG sheet steel fabricated, floor
mounted type cubical panel, suitable for operation on 380 -
440 Volts, 3 Phase, 50 Hz, fitted with accessories as below.
The incoming and outgoing cable end boxes shall be on
either sides of main panel. The cable entries from auto
transformer shall be totally enclosed in sheet metal. The
starter shall have screened louvers on both sides
 1) Oil immersed copper wound auto transformer with
50%,65%, and 80% tapping including first fill of oil.
2) All Air Break Contactors of AC 3 duty of suitable rating
as mentioned.
3) Bimetallic overload relay.
4) Timer ON and OFF delay.
5) Master timer.
6) Ammeter with CTs and selector switch.
7) No Volt release.
8) Motor 'ON", "OFF" and "TRIP" indication lamp.
9) Motor Protection Relay, solid state with protection CTs.
10) Thermostat with 1 NO + 1 NC for Oil temperature.
11) Door interlock switch with 1 NO + 1 NC.
12) Control fuse.
(With TPI)
3.00 180 HP (400/170/170) 2,59,841.00 Nos 7,79,523.00
Item No. 3 -Glandless Sluice Valve
Providing erecting Cast Steel/ Spheroidal Graphite (S.G)
Iron D/F Sluice Valves with jointing to pipe work
(including all hardware and packing) water works quality,
having non-rising spindle with hand wheel and without
bypass arrangement, spindle of stainless steel as per
requirement, inspection charges, transportation upto
departmental store, unloading, stacking, excluding GST
levied by GOI & GOM in all respect etc. excluding C. C.
foundation / structural steel support.

3.00 200 mm dia Sluice Valve CS 150 47,137.00 Nos 1,41,411.00

Item No 3B : Valve Actuator

Providing, erecting electric Valve actuators totally

enclosed, weather-proof and dust proof construction with
IP-67, protection class suitable for installation in any
position without lubrication, leakage or other operational
difficulty with special grease filled gear box and hand
wheel for emergency manual operation which will
automatically dis-engage on restoration of power to motor
and with 10 watt single phase space heater and continuous
local mechanical position indicator and individually
replaceable counter gear assembly and with two torque and
four limit switches with S.S. flap and operated with gear
driven cams and of rating 250 Volt, 5 Amp, AC/DC, torque
switch dial and with TEFC squirrel cage induction motor
working on 440 Volts +/- 10%, 3 phase, 50 Hz AC of
intermittent duty rating S-2, insulation class "F" and temp
rise restricted to class "B" with IP - 67 protection class
suitable for DOL starting and with three thermostat and
30% over load margin. The torque rating of reduction gear
box shall be atleast 1.5 times max. torque required for
opening and closing of valve with integral starter for ON &
OFF operation (With TPI)

3.00 200 mm dia 98,403.00 Nos 2,95,209.00

 Item No. 4 - Reflux Valve

Providing erecting Cast Steel /Spheroidal Graphite (S.G.) Iron

D/F Reflux Valves Single Door with jointing to pipe work
(including all hardware and packing) water works quality with
jointing to pipe without bypass arrangement, with gunmental
seats including inspection charges, transportation upto
departmental store, unloading, stacking excluding GST levied by
GOI & GOM in all respect etc. completed but excluding C. C.
foundation / structural steel support.

3.00 200 mm dia Reflux Valve CS 150 48,610.00 Nos 1,45,830.00

350 mm dia Reflux Valve CS 150 for common header
1.00 1,11,510.00 Nos 1,11,510.00
Item No. 5 - Kinetic Air Valve
Providing, erecting Kinetic Double Orifice Cast Steel Air
Valves with an isolating Sluice Valve mounted in
horizontal position operated by wheel gear suitable for
working
pressure of Class 150 rating
1.00 100 mm dia CS 150 42,467.00 Nos 42,467.00
Item No. 6 - MS DF /CI DF/ Piping specials
Providing, lowering, laying, jointing and testing MS DF/CI
DF/GI piping as per detailed specifications and approval
layout of pumping machinery and of size as per required.

3000.00 MS DF Pipes & Specials. 95.00 Kg 2,85,000.00

Item No. 7 - Concrete Foundation
Providing CC foundation in 1:2:4 ratio as per detailed
specifications. M-150
1.00 CC foundation 1:2:4 5,640.00 Cum 5,640.00
Item No. 8 - Pressure Gauges
Providing and erecting Pressure gauge Glycerine filled
Bourdon type IS 3624:1987
4.00 Pressure gauge 150 mm dia. 2,005.00 No. 8,020.00
Item No 9- Structural steel
ISMB/Chequered Plates/ Angles/ Channels of suitable size
for any purpose as per detailed design and drawing or as
directed by Engineer-in-charge including cutting, bending,
welding, fabrication, hoisting, erecting, fixing in position,
1.00 making riveted / bolted / welded connections and one coat 70,017.000 MT 70,017.00
of anticorrosive paint and over it two coats of oil painting,
etc. complete.

Item No. 10 - LT Panel

Supplying & erecting automatic control panel as per
1.00 3,56,114.55 Each 3,56,114.55
detailed specifications.
Item No 11A : Transformer
 Supplying, installing, testing & commissioning 3 phase,
11/0.433 kV, 50 Hz., 400 kVA, Mineral oil immersed and
naturally cooled outdoor type, Copper wound Non-sealed
transformer delta/star connected with additional neutral
brought out on load side, temperature rise should not
exceed 45℃ by thermometer in oil and 50℃ by the
resistance method in winding at full load rating, using type
A winding insulation (kraft paper) with HV tapping (with
1.00 off load tap changer) off load +5 to -10 in steps of 2.5%, 10,67,793.30 Each 10,67,793.30
having 7 number of tap positions withstandard accessories
complete with test certificate with losses below 1225 Watts
at 50% load, 3450 Watts at 100% load as per IS:1180 (part
1) : 2014 with necessary permissions of Electrical
Inspector, as per specification no SS- TR NSL.

Item No 11B : Substation

Providing, erecting, commissioning and testing of 11 kV
substation with all required accessories and necessary
1 7,47,168.69 Job 7,47,168.69
permissions of MSEDCL and Electrical Inspector etc
complete
Item No. 12 - Cable
A) Supplying and erecting XLPE armoured cable 1100
V grade with ISI mark
i)FR XLPE insulated, galvanised steel formed wire
30 1,065.00 rmt 31,950.00
armoured (strip) cable 1100 V, 3 core 185 sqmm
ii)FR XLPE insulated, galvanised steel formed wire
150 771.00 rmt 1,15,650.00
armoured (strip) cable 1100 V, 1 core 400 sqmm
iii)FR XLPE insulated, galvanised steel formed wire
50 617.00 rmt 30,850.00
armoured (strip) cable 1100 V, 1 core 300 sqmm
iv) Cable for actuator-FR XLPE insulated, galvanised steel
formed wire armoured (strip) cable 1100 V, 3 core 2.5 sq.
30 173.00 rmt 5,190.00
mm. copper conductor

Item No. 13 - Earthing

A)Providing earthing with Galvanized cast iron earth plate
size 60 x 60 x 0.6 cm with funnel with a wire mesh for
5.00 watering and brick masonry block C.l. covercomplete with 6,357.75 No. 31,788.75
all materials, testing & recording the results as per
specification No. EA-EP
B)Supplying and erecting GI strip of required size used for
earthing on wall and/or any other purpose with necessary
250 GI clamps fixed on wall painted with bituminous paint in 233.10 kg 58,275.00
an approved manner with joints required. As per
specification No EA-EP.
Item No. 14 - Tools
Providing tools of standard make as per detailed
1 23,048.00 Set 23,048.00
specifications.
Item No. 15 -Electromagnetic Flowmeter
 Supply, install and commission Electromagnetic Flow
Meter (EMF) As Per ISO 4064, for Raw/Pure water with
accuracy +/-0.5% of measured value & protection as per
given specifications for size 100 mm-1000mm including
sensor, transmitter surge arrestor, cable suitable size for 25
mtrs built in GSM ( with Simcard and its charges,valid for
36 months) including the pipe cutting, leveling and
installation of flow meter in the pipelines with necessary
tool tackles, cranes including 36 months guarantee etc
complete, as may be required at site & based on technical
specifications and with third party inspection

1.00 350 mm dia 3,07,184.00 No 3,07,184.00

Item No 16 : Dismantling Joints
Providing, erecting, commissioning and testing Dismantling
Joits of following diameter etc complete.
1.00 350 mm dia for flowmeter 27,718.00 No 27,718.00
3.00 200 mm dia for pumps 12,290.00 No 36,870.00
Item No 17 : Valve Chamber
:Valve Chamber With Cast Iron Manhole Frame And
Covers Providing and constructing B.B masonary valve
chamber with 15 cm thick 1:2:4 proportion PCC bedding,
excluding excavation, B.B masonary in CM 1:5 proportion,
12 mm thick cement plaster in CM 1:4 proportion on both
sides with providing and fixing C.I. manhole frame and
cover in RCC 1:1.5:3 coping or RCC 1:1.5:3 proportion
1 x15 cm thick slab, etc. complete as directed by Engineer-in- 29,656.00 No 29,656.00
charge.
As above of 1.5 x1.5 M internal size and depth upto1.5 m
with 53 cm dia CI manhole frame and cover of 90 Kg.
fixed in RCC Slab.

Item No 18 : Lifting arrangement

A) HOT : Providing , erecting and commissioning Single
Girder Hand Operated Circular / Rectangular Travelling
Crane with 6 m lift complete with chain pulley block ISI
marked and travelling trolley both tested for 50 % overload
including arrangement
for longitudinal travel / circular travel and cross travel with
wheel, hand chain, etc complete. With TPI
1.00 5 Ton Capacity Above 6m upto 8m span 3,62,164.00 Each 3,62,164.00
B) Square Bar / Rail : Providing, erecting and fixing
square bar of EN 8 as rail for over head crane on provided
track, girder / continuous corbel beam, including
supporting plate and "J" bolts.
23 50 x 50 mm (EN 8) 2,231.00 m 51,313.00
Item No 19: APFC Panel
Supplying and erecting 125 kVAr, 440 V 3 phase, 50 Hz.,
Contactor Logic & Intelligent Relay micro APFC passive
filter panel, consisting of suitable steps of APP/MPP type
1.00 3,47,338.95 Each 3,47,338.95
capacitor units with Detuned (harmonic filter) reactors of
suitable rating
 APFC panel shall be compliance to IEC 61439 and power
quality IEC 61921 standard as per specification no CP-
ED/APFC
Item No.20 : Electrification
Carrying out electrification of pump house internally and
1.00 41766.00 Job 41,766.00
externally as per detailed specifications
Item No 21: Surge vessel

Providing, fabricating, erecting, testing and commissioning

as per IS 2825 (code for unfired pressure vessels) Surge
vessel / Air Vessel fabricated in boiler quality plate
2500.00 conforming to grade I of IS 2002 with radiography testing 327.00 kg 8,17,500.00
on provided foundation including epoxy painting.
Boiler quality Plate for surge vessel
Note (Provision for foundation made in estimate for
Approach Bridge)
Total 1,44,68,062.74
Total B Part 14468062.74
Total B Part Rs. 14468062.74

AGREEMENT NO - B1/50 FOR 2022/23

DATE OF WORK ORDER - 25/01/2023
Part C :- Balance work and payment
Under Clause-38 and EIRL
Total C Part 0.00
Total C Part Rs. 0.00

AGREEMENT NO - B1/50 FOR 2022/23

DATE OF WORK ORDER - 25/01/2023
Part D :- Additional Work Required Other than
Tender
Total D Part 0.00
Total D Part Rs. 0.00

Part A :- Work Completed and Payment-Total Rs 0.00

Part B :- Balance work and payment
14468062.74
(Shedule A Part)-Total Rs
Part C :- Balance work and payment
-
Under Clause-38
Up To 25%-Total Rs. 0.00
Under Clause 38-Total Rs. 0.00
Part D :- Additional Work Required Other
0.00
than Tender (EIRL)-Total Rs

Total of Part A+B+C+D - Rs. 14468062.74

SUB DIVISONAL ENGINEER EXECUTIVE ENGINEER

MAHARASHTRA JEEVAN PRADHIKARAN MAHARASHTRA JEEVAN PRADHIKARAN
SUB DIVISON NANDURBAR DIVISION JALGAON